Manual - Audio General Inc.

Communicator Touch Panel
Installation manual
For DP-1200, DP-1500, DP-2000, DP2K-xxC and DPxK-xxB
R9855910
R59770149/02
25/04/2012
Barco nv Entertainment Division
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.36.883.86
Support: www.barco.com/esupport
Visit us at the web: www.barco.com
Printed in Belgium
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco web site
https://my.barco.com.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may
cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense
EN55022/CISPR22 Class A ITE (Information Technology Equipment)
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such equipment should not
be restricted in its sale but the following warning shall be included in the instructions for use:
Warning : This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not
agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are
system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as
well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be complied with by
the customer.
Software License Agreement
You should carefully read the following terms and conditions before using this software. Your use of this software indicates your acceptance
of this license agreement and warranty.
Terms and Conditions:
1.
No redistribution of the software is allowed.
2.
Reverse-Engineering. You may not reverse engineer, decompile, disassemble or alter anyhow this software product.
Disclaimer of Warranty:
This software and the accompanying files are sold “as is” and without warranties as to performance or merchantability or any other warranties whether expressed or implied. In no event shall Barco be liable for damage of any kind, loss of data, loss of profits, business
interruption or other pecuniary loss arising directly or indirectly. Any liability of the seller will be exclusively limited to replacement of the
product or refund of purchase price.
Disposal Information
This equipment has required the extraction and use of natural resources for its production. It may contain hazardous substances for health
and environment. In order to avoid the dissemination of those substances in the environment and to diminish the pressure on natural
resources, we encourage you to use the appropriate take-back systems. Those systems will reuse or recycle most of the materials of your
end of- life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those systems. If you need more information on the collection, reuse and recycling
systems, please contact your local or regional waste administrator. You can also contact us for more information on the environmental
performances of our products.
Disposal of batteries in the product
This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately from
municipal waste.
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols will appear
below the crossed-out wheeled bin symbol.
By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects on the
environment and human health.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufacturers.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
1. Communicator Touch Panel
1. COMMUNICATOR TOUCH PANEL
Purpose of the Communicator Touch Panel
The Communicator Touch Panel is exclusively designed for the Barco DP-1200, DP-1500, DP-2000, DP2K C series, DP2K B series
and DP4K B series Digital Cinema projectors and can thus not be used on any other equipment.
About this document
This document describes how to install the Communicator Touch Panel on the Barco DP-1200, DP-1500, DP-2000, DP2K C series,
DP2K B series and DP4K B series Digital Cinema projector. It does not describe the functionality of the user interface of the Communicator Touch Panel.
The latest version of the user guide which describes the functionality of the Communicator Touch Panel can
be downloaded from https://my.barco.com.
Check for the latest software version of the Communicator Touch Panel on https://my.barco.com.
Overview
1.1
•
Introduction
•
Content of the kit
Introduction
Communicator Touch Panel for digital cinema projectors
The Communicator Touch Panel is designed for multi-user command and control, the Communicator enables users to learn quickly
and operate efficiently - using an elegant and flexible Touch Panel interface. The interface’s commonality means that operators
can intuitively use any model in the product line, without restriction, and its user-friendly nature translates directly into a short and
enjoyable learning curve.
Image 1-1
Flexible Touch Panel interface
The Touch Panel interface can be mounted upon a swivel arm which easily fits on top of the Digital Cinema projector. One central
locking mechanism of the swivel arm allows an instant fixation of the Touch Panel interface in any position.
The Touch Panel interface can also be installed further away from the Digital Cinema projector. For that you can use a serial (RS232)
cable up to 10 meter or an Ethernet cable up to 50 meter to realize a direct data communication between the Digital Cinema projector
and the Communicator Touch Panel.
The Touch Panel interface can also be connected with a Local Area Network (LAN) just like the Digital Cinema projector. In this
case both devices can communicate with each other as well.
The Touch Panel interface requires a voltage supply +12 VDC and 1,5 ampere. Note that the Digital Cinema projector has a 12 VDC
output which can be used to power up the Touch Panel interface. Nevertheless, the use of a separate +12 VDC adaptor (1,5 ampere
minimum) is required in case the Touch Panel interface is installed more then a few meters away from the Digital Cinema projector.
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
1
1. Communicator Touch Panel
1.2
Content of the kit
Order info & content of the kit
When ordering the Communicator Touch Panel for the Barco DP-1200, DP-1500, DP-2000, DP2K C series, DP2K B series and
DP4K B series Digital Cinema projectors, refer to article number R9855910.
The table below gives an overview of the content of the kit.
2
Article number
Description
R59770149
1
image 1-2
R765314
Installation manual (this
document)
Touch Panel unit
Image
1
image 1-3
Z3499792
Multi cable
1
image 1-4
R856887
Mounting plate
1
image 1-5
B359907
Swivel arm
1
image 1-6
V3675041
Spring washer (D6.4D11)
1
image 1-7
V367513
Spring washer (D10.5D18)
1
image 1-8
Quantity
R366105
Nut (M6)
1
image 1-9
B362175
Velcro strip
2
image 1-10
B364267
Spacer
1
image 1-11
Image 1-2
Image 1-3
Image 1-4
Image 1-5
Image 1-6
Image 1-7
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
1. Communicator Touch Panel
Image 1-8
Image 1-9
Image 1-10
Image 1-11
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
3
1. Communicator Touch Panel
4
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
2. Installation procedures (for DP-1200, DP-1500, DP-2000 and DP2K-xxC)
2. INSTALLATION PROCEDURES (FOR DP-1200,
DP-1500, DP-2000 AND DP2K-XXC)
2.1
Installing the Touch Panel interface
Necessary tools
•
17 mm wrench.
•
10 mm wrench.
How to install the Touch Panel interface upon the projector?
1. Assemble the mounting plate and the swivel arm together as illustrated. First place the nut (N) upon the rod of the mounting
plate, then add the lock washer (L), then fasten the mounting plate and the swivel arm together. When the arm is mounted, turn
nut (N) against the arm to secure the position. (image 2-1)
2. Slide a washer (M) over the base of the swivel arm and Insert the base of the swivel arm into the mounting hole at the top of the
projector as illustrated. (image 2-2)
3. Place the Touch Panel interface upon the mounting plate of the swivel arm and fasten the two wing nuts (W) as illustrated.
(image 2-3)
4. Connect the circular plug of the multi cable with the circular socket at the rear side of the projector. (image 2-4)
5. Attach the multi cable to the swivel arm using the two Velcro strips.
6. Connect the DC plug, the RJ45 Ethernet plug and the D-SUB plug into their respective sockets on the Touch Panel interface.
(image 2-5)
N
L
Image 2-1
Assemble swivel arm
M
Image 2-2
Mount swivel arm
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
5
2. Installation procedures (for DP-1200, DP-1500, DP-2000 and DP2K-xxC)
W
Image 2-3
Mount Touch Panel
Image 2-4
Connections
Image 2-5
Connections
2.2
Reposition the Touch Panel interface
How to reposition the Touch Panel interface?
1. Hold fast the Touch Panel interface.
2. Release the central swivel clamp by turning the big black knob (K) counterclockwise. (image 2-6)
3. Move the Touch Panel interface into the desired position.
4. Fasten the central swivel clamp by turning the big black knob clockwise.
6
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
2. Installation procedures (for DP-1200, DP-1500, DP-2000 and DP2K-xxC)
K
Image 2-6
CAUTION: Never release the central swivel lock without supporting the Touch Panel interface.
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
7
2. Installation procedures (for DP-1200, DP-1500, DP-2000 and DP2K-xxC)
8
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
3. Installation procedures (for DPxK-xxB)
3. INSTALLATION PROCEDURES (FOR DPXK-XXB)
3.1
Installing the Touch Panel interface
Necessary tools
•
17mm open end wrench.
•
10mm open end wrench.
How to install the Touch Panel interface upon the projector?
1. Assemble the mounting plate and the swivel arm together as illustrated. First the nut (N) upon the rod of the mounting plate, then
the lock washer (L), and then fasten mounting plate and swivel arm together. When arm is mounted, turn nut (N) against the arm
to secure the position. (image 3-1)
2. Slide the 10mm spacer (reference 1 ) over the base of the swivel arm and insert he base of the swivel arm into one of the mounting
holes at the rear top side of the projector. (image 3-2)
3. Place the Touch Panel interface upon the mounting plate of the swivel arm and fasten the two wing nuts (W) as illustrated.
(image 3-3)
4. Connect the DC plug, the RJ45 Ethernet plug and the D-SUB plug into their respective sockets on the Touch Panel interface.
(image 3-4)
5. Connect the circular plug of the multi cable with the circular socket at the right side (reference 2) of the projector. (image 3-5)
6. Attach the multi cable to the swivel arm using the two Velcro strips.
N
L
Image 3-1
1
Image 3-2
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
9
3. Installation procedures (for DPxK-xxB)
W
Image 3-3
Image 3-4
2
Image 3-5
3.2
Reposition the Touch Panel interface
How to reposition the Touch Panel interface?
1. Hold fast the Touch Panel interface.
2. Release the central swivel clamp by turning the big black knob counterclockwise.
3. Move the Touch Panel interface into the desired position.
4. Fasten the central swivel clamp by turning the big black knob clockwise.
10
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
3. Installation procedures (for DPxK-xxB)
CAUTION: Never release the central swivel lock without supporting the Touch Panel interface.
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
11
3. Installation procedures (for DPxK-xxB)
12
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
4. Environmental information
4. ENVIRONMENTAL INFORMATION
4.1
Disposal information
Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2002/96/EC governing waste from electrical and
electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste
and recycle them responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service.
For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee
Disposal of batteries in the product
This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately
from municipal waste.
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols will
appear below the crossed-out wheeled bin symbol.
By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects
on the environment and human health.
4.2
Rohs compliance
中国大陆 RoHS (Information for China ROHS compliance)
根据中国大陆《电子信息产品污染控制管理办法》(也称为中国大陆RoHS), 以下部分列 出了Barco产品中可能包含的有毒和/或有
害物质的名称和含量。中国大陆RoHS指令包含在 中国信息产业部MCV标准:“电子信息产品中有毒物质的限量要求”中。
According to the “China Administration on Control of Pollution Caused by Electronic Information Products” (Also called RoHS of
Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may
contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the
section “Limit Requirements of toxic substances in Electronic Information Products”.
Table of toxic and hazardous substances/elements and their content, as required by China’s management methods for controlling
pollution by electronic information products
零件项目(名称)
有毒有害物质或元素
Component name
Hazardous substances and elements
铅
印制电路配件
汞
镉
六价铬
多溴联苯
多溴二苯醚
Pb
Hg
Cd
Cr6+
PBB
PBDE
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
Printed Circuit Assemblies
显示制电路裝配
Display Printed Circuit Assembly
液晶面板
LCD Panel
插入式插件
Plug assembly
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
13
4. Environmental information
零件项目(名称)
有毒有害物质或元素
Component name
Hazardous substances and elements
铅
外接电(线)缆
汞
镉
六价铬
多溴联苯
多溴二苯醚
Pb
Hg
Cd
Cr6+
PBB
PBDE
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
External Cables
內部线路
Internal wiring
底架
Chassis
电源供应器
Power Supply Unit
散热片(器)
Heatsinks
键盘
Keyboard
显示 (器)
Display
电池(组)
Batteries
塑胶外壳
Plastic Enclosure
螺帽,螺钉(栓),螺旋( 钉),垫圈, 紧 固件
Nuts, bolts, screws, washers, Fasteners
文件说明书
Paper Manuals
光盘说明书
CD Manual
装置配件
Installation kit
O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下.
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the
limit requirement in SJ/T11363-2006.
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is
above the limit requirement in SJ/T11363-2006
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子信息产品污染控制 标识要求》标准贴上环保使用期限(EFUP)
标签。Barco产品所采用的EFUP标签(请参阅 实例,徽标内部的编号使用于制定产品)基于中国大陆的《电子信息产品环保使用期
限通 则》标准。
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with the “Electronic Information Products
Pollution Control Labeling Standard” of Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The
number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “Standard of Electronic Information Products
Environmental Friendly Use Period” of Chinese Mainland.
14
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
4. Environmental information
10
R59770149 COMMUNICATOR TOUCH PANEL 25/04/2012
15