ACCO Brands NOBO X20P User`s guide

Table of Contents
Table of Contents ......................................................................................... 1
Usage Notice ................................................................................................ 2
Precautions...........................................................................................................2
Introduction................................................................................................... 4
Product Features ..................................................................................................4
Package Overview................................................................................................5
Product Overview .................................................................................................6
Main Unit ........................................................................................................................6
Control Panel .................................................................................................................7
Connection Ports ...........................................................................................................7
Remote Control with Laser Pointer ................................................................................8
Installation .................................................................................................... 9
Connecting the Projector ......................................................................................9
Powering On/Off the Projector............................................................................10
Powering On the Projector ...........................................................................................10
Powering Off the projector ........................................................................................... 11
Warning Indicator ......................................................................................................... 11
Adjusting the Projected Image............................................................................12
Adjusting the Projector Image Height ..........................................................................12
Adjusting the Projector Zoom / Focus ..........................................................................13
Adjusting Projected Image Size ...................................................................................13
User Controls ............................................................................................. 14
Control Panel & Remote Control ........................................................................14
On-Screen Display Menus..................................................................................16
How to Operate ...........................................................................................................16
Menu Tree ..........................................................................................................17
Language .....................................................................................................................18
Image-I ........................................................................................................................19
Image-II (Computer Mode)...........................................................................................21
Image-II (Video Mode) .................................................................................................23
Audio ............................................................................................................................25
Management ................................................................................................................26
Lamp Setting ................................................................................................................27
Appendices................................................................................................. 28
Troubleshooting ..................................................................................................28
Replacing the Lamp............................................................................................32
Compatibility Modes ...........................................................................................33
1
English
Usage Notice
Precautions
Follow all warnings, precautions and maintenance as recommended in this user’s guide to maximize the life of your unit.
Warning- Do not look into the projector’s lens when the lamp is
on. The bright light may hurt your eyes.
Warning- To reduce the risk of !re or electric shock, do not expose
this product to rain or moisture.
Warning- Please do not open or disassemble the product as this
may cause electric shock.
Warning- When changing the lamp, please allow unit to cool
down, and follow all changing instructions.
Warning- This product will detect the life of the lamp itself.
Please be sure to change the lamp when it shows warning messages.
Warning- Reset the “Lamp Reset” function from the On Screen
Display “Lamp Setting” menu after replacing the lamp
module (refer to page 27).
Warning- When switching the projector off, please ensure the
projector completes its cooling cycle before disconnecting power.
Warning- Turn on the projector !rst and then the signal sources.
Warning- Do not use lens cap when projector is in operation.
Warning- When the lamp reaches the end of its life, it will burn
out and may make a loud popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow
the procedures listed under “Replacing the Lamp”. (see
page 32)
English
2
Usage Notice
Do:
!"Turn off the product before cleaning.
!"Use a soft cloth moistened with mild detergent to clean the
display housing.
!"Disconnect the power plug from AC outlet if the product is not
being used for a long period of time.
Don’t:
!"Block the slots and openings on the unit provided for ventilation.
!"Use abrasive cleaners, waxes or solvents to clean the unit.
!"Use under the following conditions:
- In extremely hot, cold or humid environments.
- In areas susceptible to excessive dust and dirt.
- Near any appliance that generates a strong magnetic !eld.
- In direct sunlight.
3
English
Introduction
Product Features
Congratulations and Thank You for choosing an X20P projector, an NOBO Product. This product is a XGA single chip
0.55” DLPTM projector. Outstanding features include:
# True XGA, 1024 x 768 addressable pixels
# Texas Instruments Single chip DLPTM Technology
# NTSC/NTSC4.43/PAL/PAL-M/PAL-N/SECAM and
HDTV compatible (480i/p, 576i/p, 720p, 1080i)
# Multi-Auto functions: Auto detection, Automatic saving
of user adjustments
# IR remote control with laser pointer
# User friendly multilingual on screen menu
# Advanced digital keystone correction and high quality
full screen image re-scaling
# User friendly control panel
# One built-in speaker
# UXGA, SXGA+, SXGA compression and SVGA, VGA resizing
# Mac compatible
English
4
Introduction
Package Overview
This projector comes with all the items shown below. Check to
make sure your unit is complete. Contact your dealer immediately if anything is missing.
!"Due to the difference in applications
for each country,
some regions may
have different accessories.
Projector with lens cap
Power Cord 1.8m
VGA Cable 1.8m
Composite Video Cable
1.8m
Wireless Remote
Controller
SCART VGA/S-Video
Adaptor
(available in European
region only)
2 x AA Batteries
Carry Bag
Documents :
User’s Guide
$"
Quick Start Card
$"
Warranty Card
$"
Quick Troubleshooting Guide
$"
5
English
Introduction
Product Overview
Main Unit
2
1
3
7
6
8
6
7
8
4
5
2
1
9
English
6
1.
2.
3.
4.
5.
6.
7.
8.
9.
Control Panel
Zoom Lever
Power Socket
Speaker
Elevator Button
Zoom Lens
Focus Ring
IR Receivers
Connection Ports
Introduction
Control Panel
4
3
5
1.
2.
3.
4.
6
Enter
Menu (On/Off)
Power
Four Directional Select
Keys
2
7
5.
6.
7.
8.
9.
1
8
9
Source Select
Resync
Power LED
Lamp Indicator LED
Temp Indicator LED
Connection Ports
6
5
4
3
2
1
1. VGA-In Connector (PC Analog signal/SCART RGB/
HDTV/Component Video Input)
2. Composite Video Input Connector
3. S-Video Input Connector
4. Audio Input Connector
5. Service Connector
6. KensingtonTM Lock Port
7
English
Introduction
Remote Control with Laser Pointer
8
1
9
2
3
English
8
10
4
11
5
12
6
13
7
1. Laser Button
2. Four Directional Select
Keys
3. Keystone +/4. Page Up
5. Page Down
6. Source Select
7. Freeze
8. Power
9. Menu
10. Enter
11. Mute
12. Resync
13. Hide
Installation
Connecting the Projector
RGB
1
2
!"Due to the difference in applications
for each country,
some regions may
have different accessories.
1
7
S-Video Output
5
4
3
Video Output
6
DVD Player, Settop Box,
HDTV receiver
1................................................................................................................ VGA Cable
2.............................................................Audio Input Cable (Optional Accessory)
3.......................................................................................... Composite Video Cable
4.....................................................................S-Video Cable (Optional Accessory)
5......................................................... Audio Output Cable (Optional Accessory)
6.......................................SCART VGA/S-Video Adaptor (For European Only)
7..................................... D-15 to RCA Adapter for YPbPr (Optional Accessory)
! To ensure the projector works well with your computer,
please set the display mode of your graphic card less than
or equal to 1600 x 1200 resolution. Make sure the timing of
the display mode is compatible with the projector. Refer to
the “Compatibility Modes” section on page 33.
9
English
Installation
Powering On/Off the Projector
Powering On the Projector
1. Remove the lens cap. %
2. Ensure that the power cord and signal cable are securely
connected. The Power LED will !ash green.
3. Turn on the lamp by pressing “Power” button on the control
panel.& And the Power LED will turn green.
4. Turn on your source (computer, notebook, video player,
etc.). The projector will detect your source automatically
within “Management” menu; check that “Source Lock” has
been set to “Off”.
!"If you connect multiple sources at the same time, use the
“Source” button on the control panel or on remote control to
switch.
2
Power
!"Turn on the projector !rst and then
the signal sources.
1
English
10
Lens Cap
Installation
Powering Off the Projector
1. Press the “Power” button to turn off the projector lamp; you
will see a message
displayed on the projector’s screen. Press the “Power” button again to con!rm, otherwise the message will disappear
after 5 seconds.
Please note that if the key is pressed instead, the projector will enter the “Picture Mute” mode and no image will
be displayed. To exit the “Picture Mute” mode, press the
“Power” button again.
2. The cooling fans continue to operate for about 20 seconds
for cooling cycle and the Power LED will turn green. When
the Power LED begins "ashing, the projector has entered
standby mode.
If you wish to turn the projector back on, you must wait
until the projector has completed the cooling cycle and has
entered standby mode. Once in standby mode, simply press
“Power” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and the
projector.
4. Do not turn on the projector immediately following a power
off procedure.
Warning Indicator
! When the “LAMP” indicator lights solid red, the projector
will automatically shut itself down. Please contact your local
reseller or service center.
! When the “TEMP” indicator lights solid red for about 60
seconds, it indicates the projector has been overheated. The
projector will automatically shut itself down.
Under normal conditions, the projector can be switched on
again after it has cooled down. If the problem persists, you
should contact your local dealer or our service center.
! When the “TEMP” indicator lights solid red, it indicates the
fan failed. Please contact your local dealer or our service
center.
11
English
Installation
Adjusting the Projected Image
Adjusting the Projector Image Height
The projector is equipped with elevator foot for adjusting the
image height.
To raise the image:
1. Press the elevator button %.
2. Raise the image to the desired height angle &, then release
the button to lock the elevator foot into position.
3. Use screw in feet ' to !ne-tune the display angle.
To lower the image:
1. Press the elevator button.
2. Lower the image, then release the button to lock the elevator foot into position.
3. Use screw in feet ' to !ne-tune the display angle.
Elevator Button
1
3
2
Tilt Adjusting Foot
Elevator Foot
English
12
Installation
Adjusting the Projector Zoom / Focus
You may turn the zoom lever to zoom in or out. To focus the
image, rotate the focus ring until the image is clear. The projector will focus at distances from 4.9 to 39.4 feet (1.5 to 12.0
meters) with mechanical travel.
Zoom Lever
Focus Ring
Adjusting Projection Image Size
Screen
(Diagonal)
Max.
38.1”(96.8cm)
76.2”(193.6cm)
127.1”(322.7cm)
177.9”(451.8cm)
228.7”(580.9cm)
304.9”(774.5cm)
Min.
34.7”(88.1cm)
69.3”(176.1cm)
115.6”(293.5cm)
161.8”(410.9cm)
208.0”(528.3cm)
277.3”(704.4cm)
Screen
Max.
30.5”x 22.9”
61.0” x 45.7”
101.7” x 76.3”
142.3” x 106.7”
183.0” x 137.2”
243.9” x 182.9”
(WxH)
77.4 x 58.1cm
154.9 x 116.2cm
258.2 x 193.6cm
361.4 x 271.1cm
464.7 x 348.5cm
619.6 x 464.7cm
Size
Hd
Distance
Min.
27.8” x 20.8”
55.4” x 41.6”
92.5” x69.4”
129.4” x 97.1”
166.4” x 124.8”
221.8” x 166.4”
(WxH)
70.5 x 52.9cm
140.9 x 105.7cm
234.8 x 176.1cm
328.7 x 246.5cm
422.6 x 317.0cm
563.5 x 422.6cm
Max.
3.4” (8.7cm)
6.9” (17.4cm)
11.4” (29.0cm)
16.0” (40.7cm)
20.6” (52.3cm)
27.4” (69.7cm)
Min.
3.1” (7.9cm)
6.2” (15.9cm)
10.4” (26.4cm)
14.6” (37.0cm)
18.7” (47.6cm)
25.0” (63.4cm)
4.9’ (1.5m)
9.8’ (3.0m)
16.4’ (5.0m)
22.3’ (7.0m)
29.5’ (9.0m)
39.4’ (12.0m)
!This graph is for user’s reference only.
13
English
User Controls
Control Panel & Remote Control
There are two ways for you to control the functions: Remote
Control and Control Panel.
Using the Control Panel
1
Power
Source
14
Refer to the “Power On/Off the Projector” section
on pages 10-11.
1
Press “Source” to select an input signal.
Menu
Turns the menu On or Off.
Four Directional Select
Keys
Use
Enter
Con!rm your item selection.
Resync
English
2
2
to navigate through the menus.
Automatically synchronizes the projector to the
input source.
User Controls
Using the Remote Control
Power
Refer to the “Power On/Off the Projector” section
on pages 10-11.
Resync
Automatically synchronizes the projector to the
input source.
Laser Button
Aim the remote at the viewing screen, press and
hold this button to activate the laser pointer.
Source
Press “Source” to select an input signal.
Keystone
Adjusts image distortion caused by tilting the
projector (±16 degrees).
Mute
Momentarily turns off the audio.
Hide
Momentarily turns off the picture.
Freeze
Press “Freeze” to pause the screen image.
Page Up
Use this button to page up.
Page Down
Use this button to page down.
Four Directional Select
Keys
Use
Menu
Display or exits the on-screen display menus for
projector.
Enter
Con!rm your item selection.
to navigate through the menus.
15
English
User Controls
On Screen Display Menus
The Projector has multilingual On Screen Display menus that
allow you to make image adjustments and change a variety of
settings. The projector will automatically detect the source.
How to Operate
1. To open the OSD menu, press “Menu” on the Remote Control or
Control Panel.
2. When OSD is displayed, use
keys to select any item in the
main menu. While making a selection on a particular page, press
key to enter sub menu.
3. Use
by
keys to select the desired item and adjust the settings
key.
4. Select the next item to be adjusted in the sub menu and adjust as
described above.
5. Press “Menu” to con!rm, and the screen will return to the main
menu.
6. To exit, press “Menu” again. The OSD menu will close and the
projector will automatically save the new settings.
Main Menu
English
16
Sub Menu
Setting
User Controls
Menu Tree
17
English
User Controls
Language
Language
Choose the multilingual OSD menu. Use the
your preferred language.
Press “Enter” to !nalize the selection.
English
18
or
key to select
User Controls
Image-I
Display Mode
There are many factory presets optimized for various types of images.
! PC: For computer or notebook. (brightest image)
! Movie: For home theater.
! sRGB: For standard PC color. (best color reproduction)
! Bright: For bright mode.
! User: Memorize user’s settings.
Brightness
Adjust the brightness of the image.
! Press the
to darken image.
! Press the
Contrast
to lighten the image.
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
! Press the to decrease the contrast.
! Press the to increase the contrast.
Keystone (Keystone Correction)
Adjusts image distortion caused by tilting projector. (±16 degrees)
Color
Press “Enter” to adjust the red, green and blue colors.
White Peaking
Use the white peaking control to set the white peaking level of
DMD chip. 0 stands for minimal peaking, and 10 stands for maxi-
19
English
User Controls
mum peaking. If you prefer a brighter image, adjust towards the
maximum setting. For a smooth and more natural image, adjust
towards the minimum setting.
Color Temp.
Adjusts the color temperature. At higher temperature, the screen
looks colder; at lower temperature, the screen looks warmer.
English
20
User Controls
Image-II
(Computer Mode)
Frequency
“Frequency” changes the display data frequency to match the frequency of your computer’s graphic card. If you experience a vertical
"ickering bar, use this function to make an adjustment.
Tracking
“Tracking” synchronizes the signal timing of the display with the
graphic card. If you experience an unstable or "ickering image, use
this function to correct it.
H Position (Horizontal Position)
! Press the to move the image left.
! Press the to move the image right.
V Position (Vertical Position)
! Press the to move the image down.
! Press the to move the image up.
Degamma
This allows you to choose a degamma table that has been !ne-tuned
to bring out the best image quality for the input.
Aspect Ratio
Use this function to choose your desired aspect ratio.
!
4:3 : The input source will be scaled to !t the projection
screen.
!
16:9 : The input source will be scaled to !t the width of the
screen.
!
Window: When a 4:3 image is bigger than a 16:9 screen, select the “Window” mode to !t the image onto the screen without
changing the projection distance.
21
English
User Controls
Display area
Picture area
Input Signal
Display on Screen
16:9 Image Position
Adjust the image position up or down, when you select the aspect
ratio of 16:9.
! Press the
! Press the
!"“16:9 Image Position” function is
supported under
16:9 aspect ratio.
English
22
to move the image down.
to move the image up.
User Controls
Image-II
(Video Mode)
Degamma
This allows you to choose a degamma table that has been !ne-tuned
to bring out the best image quality for the input.
Saturation
Adjusts a video image from black and white to fully saturated color.
! Press the
! Press the
Tint
to decrease the amount of saturation in the image.
to increase the amount of saturation in the image.
Adjusts the color balance of red and green.
! Press the to decrease the amount of green in the image.
! Press the to increase the amount of red in the image.
Sharpness
Adjusts the sharpness of the image.
!"“Saturation”,
“Tint” and “Sharpness” function is
not supported under DVI-D mode.
! Press the to decrease the sharpness.
! Press the to increase the sharpness.
Aspect Ratio
Use this function to choose your desired aspect ratio.
!
4:3 : The input source will be scaled to !t the projection
screen.
!
16:9 : The input source will be scaled to !t the width of the
screen.
!
Window: When a 4:3 image is bigger than a 16:9 screen, select the “Window” mode to !t the image onto the screen without
changing the projection distance.
23
English
User Controls
Display area
Picture area
Input Signal
Display on Screen
16:9 Image Position
Adjust the image position up or down, when you select the aspect
ratio of 16:9.
! Press the
! Press the
!"“16:9 Image Position” function is
supported under
16:9 aspect ratio.
English
24
to move the image down.
to move the image up.
User Controls
Audio
Volume
! Press
! Press
Mute
to decrease the volume.
to increase the volume.
! Choose the left icon to turn mute on.
! Choose the right icon to turn mute off.
25
English
User Controls
Management
Menu Location
Choose the menu location on the display screen.
Projection
!
Front-Desktop
The factory default setting.
!
Rear-Desktop
When you select this function, the projector reverses the image
so you can project from behind a translucent screen.
Signal Type
Select signal type RGB or Video sources.
Source Lock
! Off: The projector will search for other signals if the current
input signal is lost.
! On: The projector will search speci!ed connection port.
Reset
Return the adjustments and settings to the factory default values.
! Yes (Execute): Returns the settings for all menus to factory default values.
! No (Cancel): Cancel the revised settings.
English
26
User Controls
Lamp Setting
Lamp Hours
Displays the cumulative lamp operating time.
Lamp Reset
Resets the lamp life hour counter after replacing the lamp.
Lamp Reminder
Choose this function to show or to hide the warning message
when the changing lamp message is displayed. The message will
appear 30 hours before end of life.
ECO Mode
Choose “On” to dim the projector lamp which will lower power
consumption and extend the lamp life by up to 130%. Choose
”Off” to return to normal mode.
Auto Power Off
Sets the countdown timer interval. The countdown timer will start,
when there is no signal being sent to the projector. Then projector
will automatically power off when the countdown has !nished.
27
English
Appendices
Troubleshooting
If you experience trouble with the projector, refer to the following information. If the problem persists, please contact your
local reseller or service center.
Problem: No image appears on screen
! Ensure all the cables and power connections are correctly and
!
!
!
securely connected as described in the “Installation” section.
Ensure the pins of connectors are not crooked or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp” section.
Make sure you have removed the lens cap and the projector is
switched on.
! Ensure that the “Hide” feature is not turned on.
Problem: Left of right edge of the image is missing or the image is unstable or noisy
! Press “Resync” on the remote control or press “ ” on control
panel.
! If you are using a PC:
For Windows 3.x:
1. In the Windows Program Manager, double click the “Windows
Setup” icon in the Main group.
2. Verify that your display resolution setting is less than or equal
to 1600 x 1200.
For Windows 95, 98, 2000, XP:
1. From the “My Computer” icon, open the “Control Panel”
folder, and double click the “Display” icon.
2. Select the “Settings” tab.
3. Click on the “Advanced Properties” button.
If the projector is still not projecting the whole image, you will
also need to change the monitor display you are using. Refer to
the following steps.
English
28
4. Verify the resolution setting is less than or equal to 1600 x 1200
resolution.
Appendices
5. Select the “Change” button under the “Monitor” tab.
6. Click on “Show all devices.” Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
! If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the computer.
2. Press the toggle output settings. Example: [Fn]+[F4]
Compaq=> [Fn]+[F4]
HewlettDell =>
[Fn]+[F8]
Packard => [Fn]+[F4]
Gateway=> [Fn]+[F4]
NEC=>
[Fn]+[F3]
IBM=>
[Fn]+[F7]
Toshiba => [Fn]+[F5]
Mac Apple:
System Preference-->Display-->Arrangement-->Mirror
display
! If you experience dif!culty changing resolutions or your monitor
freezes, restart all equipment including the projector.
Problem: The screen of the Notebook or PowerBook computer
is not displaying a presentation
! If you are using a Notebook PC:
Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each has a different way to be
reactivated. Refer to your computer’s documentation for detailed
information.
Problem: Image is unstable or !ickering
! Use “Tracking” to correct it.
! Change the monitor color setting on your computer.
Problem: Image has vertical !ickering bar
! Use “Frequency” to make an adjustment.
! Check and recon!gure the display mode of your graphic card to
make it compatible with the product.
Problem: Image is out of focus
! Adjusts the Focus Ring on the projector lens.
29
English
Appendices
! Make sure the projection screen is between distance 4.9 to 39.4 feet
(1.5 to 12.0 meters) from the projector. See page 13.
Problem: The image is stretched when displaying 16:9 DVD
The projector automatically detects 16:9 DVD and adjusts the aspect
ratio by digitizing to full screen with 4:3 default setting.
If the image is still stretched, you will also need to adjust the aspect
ratio by referring to the following:
! Please select 4:3 aspect ratio type on your DVD player if you are
playing a 16:9 DVD.
! If you can’t select 4:3 aspect ratio type on your DVD player, please
select 4:3 aspect ratio in the on screen menu.
Problem: Lamp burns out or makes a popping sound
! When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. If this happens, the projector will not
turn on until the lamp module has been replaced. To replace the
lamp, follow the procedures in the “Replacing the Lamp”.
Problem: LED lighting message
Power-LED
Message
(Green)
Standby state (Input power cord)
Lamp-LED
Temp-LED
Flashing 0.5Hz
Warming
Flashing 1Hz
Lamp lighting/Power on
Power off (Cooling)
Error (Lamp fail)
Error (Thermal fail)
Standby
mode
Operation
Mode
Flashing 2Hz
Thermal fail
Recovered
Thermal
fail
Recovered
Steady light =>
No light =>
30
T<3min.
(Fan cooling)
T>3min.
(Fan off)
Flashing 0.5Hz
Flashing 0.5Hz
Flashing 0.5Hz
Error (Fan fail)
Flashing 0.5Hz
Lamp fail retry
Flashing 0.5Hz
Flashing 0.5Hz
Error (Over temp.)
Error (Lamp breakdown)
English
Flashing 1Hz
Flashing 1Hz
Flashing 0.5Hz
Flashing 1Hz
Flashing 1Hz
Appendices
Problem: Message Reminders
! Fan fail:
! Over temperature:
! Power Off:
! Replace the lamp:
31
English
Appendices
Replacing the Lamp
The projector keeps track of the lamp usage. It will show you a
warning message
Warning: Lamp
compartment is hot!
Allow 30 minutes
to cool down before
changing lamp!
When you see this message, change the lamp as soon as possible. Make sure the projector has cooled down for at least 30
minutes before changing the lamp.
1
3
2
4
Lamp Replacement Procedure:
Warning: To
reduce the risk of
personal injury, do not
drop the lamp module
or touch the lamp bulb.
The bulb may shatter
and cause injury if it is
dropped.
1. Switch off the power to the projector by pressing the Power
button.
2. Allow the projector to cool down for at least 30 minutes.
3. Disconnect the power cord.
4. Use a screwdriver to remove the screws from the cover.%
5. Push up and remove the cover.&
6. Remove the 2 screws from the lamp module.'
7. Pull out the lamp module.(
To replace the lamp module, reverse the previous steps.
English
32
Appendices
Compatibility Modes
(ANALOG)
Mode
Resolution
V.Frequency
(Hz)
H.Frequency
(kHz)
VESA VGA
640 x 350
70
31.5
VESA VGA
640 x 350
85
37.9
VESA VGA
640 x 400
85
37.9
VESA VGA
640 x 480
60
31.5
VESA VGA
640 x 480
72
37.9
VESA VGA
640 x 480
75
37.5
VESA VGA
640 x 480
85
43.3
VESA VGA
720 x 400
70
31.5
VESA VGA
720 x 400
85
37.9
VESA SVGA
800 x 600
56
35.2
VESA SVGA
800 x 600
60
37.9
VESA SVGA
800 x 600
72
48.1
VESA SVGA
800 x 600
75
46.9
VESA SVGA
800 x 600
85
53.7
VESA XGA
1024 x 768
60
48.4
VESA XGA
1024 x 768
70
56.5
VESA XGA
1024 x 768
75
60.0
VESA XGA
1024 x 768
85
68.7
* VESA SXGA
1152 x 864
70
63.8
* VESA SXGA
1152 x 864
85
77.1
* VESA SXGA
1280 x 1024
60
63.98
* VESA SXGA
1280 x 1024
75
79.98
* VESA SXGA+
1400 x 1050
60
63.98
* VESA UXGA
1600 x 1200
60
75
MAC LC 13”
640 x 480
66.66
34.98
MAC II 13”
640 x 480
66.68
35
MAC 16”
832 x 624
74.55
49.725
MAC 19”
1024 x 768
75
60.24
* MAC
1152 x 870
75.06
68.68
MAC G4
640 x 480
60
31.35
i MAC DV
1024 x 768
75
60
* i MAC DV
1152 x 870
75
68.49
* i MAC DV
1280 x 960
75
75
Remark : “*”compressed computer
image.
33
English