Total Access 900 Series
Hardware Installation Guide
Total Access 912
Total Access 916
Total Access 924
61210916L1-34A
May 2005
Trademarks
Total Access 900 Series Hardware Installation Guide
Trademarks
Any brand names and product names included in this manual are trademarks, registered trademarks, or
trade names of their respective holders.
Total Access® is a registered trademark of ADTRAN, Inc.
To the Holder of the Manual
The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change
the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential damages or for
commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
Software Licensing Agreement
Each ADTRAN product contains a single license for ADTRAN supplied software. Pursuant to the
Licensing Agreement, you may: (a) use the software on the purchased ADTRAN device only and (b) keep
a copy of the software for backup purposes. This Agreement covers all software installed on the system as
well as any software available on the ADTRAN website. In addition, certain ADTRAN systems may
contain additional conditions for obtaining software upgrades.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: (256) 963-8000
Copyright © 2005 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.
2
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
Conventions
Conventions
Notes provide additional useful information.
Cautions signify information that could prevent service interruption or damage to
equipment.
Warnings provide information that could prevent endangerment to human life.
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
3
Safety Instructions
Total Access 900 Series Hardware Installation Guide
Safety Instructions
When using your telephone equipment, please follow these basic safety precautions to reduce the risk of
fire, electrical shock, or personal injury:
1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote
risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of
batteries in a fire. They may explode. Check with local codes for special disposal instructions.
5. The socket-outlet shall be installed near the equipment and shall be easily accessible.
Save These Important Safety Instructions
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
4
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
FCC-Required Information
FCC-Required Information
FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of FCC rules and requirements adopted by ACTA. Each
registered interface has a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, provide this information to the telephone company.
2. If this equipment causes harm to the telephone network, the telephone company may temporarily
discontinue service. If possible, advance notification is given; otherwise, notification is given as
soon as possible. The telephone company will advise the customer of the right to file a complaint
with the FCC.
3. The telephone company may make changes in its facilities, equipment, operations, or procedures
that could effect the proper operation of this equipment. Advance notification and the opportunity
to maintain uninterrupted service are given.
4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty
information. The telephone company may require this equipment to be disconnected from the
network until the problem is corrected or it is certain the equipment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. This equipment is designed to connect to the telephone network or premises wiring using an
FCC-compatible modular jack, which is compliant with Part 68 and requirements adopted by ACTA.
7. The following information may be required when applying to the local telephone company for
leased line facilities:
Part Number
Registration
Number
4210912L1
4210916L1
4210924L1
US: HDCDENAN4213616L1
Service Type
1.544 Mbps - SF
1.544 Mbps - SF and B8ZS
1.544 Mbps - ESF
1.544 Mbps - ESF and B8ZS
REN/SOC
FIC
USOC
6.0N
04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN
RJ-21X
8. The REN is useful in determining the quantity of devices you may connect to your telephone line
and still have all of those devices ring when your number is called. In most areas, the sum of the
RENs of all devices should not exceed five. To be certain of the number of devices you may
connect to your line as determined by the REN, call your telephone company to determine the
maximum REN for your calling area.
9. This equipment may not be used on coin service provided by the telephone company. Connection
to party lines is subject to state tariffs. Contact your state public utility commission or corporation
commission for information.
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
5
FCC Radio Frequency Interference Statement
Total Access 900 Series Hardware Installation Guide
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
6
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
Industry Canada Compliance Information
Industry Canada Compliance Information
Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the
“IC:” in front of the certification/registration number) signifies that the Industry Canada technical
specifications were met.
Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the
documentation or on the product labeling/markings. The REN assigned to each terminal device indicates
the maximum number of terminals that can be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the
RENs of all the devices should not exceed five (5).
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Department of Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques
de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee
par le ministre des Communications
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
7
Affidavits
Total Access 900 Series Hardware Installation Guide
Affidavits
Affidavit Requirements for Connection to Digital Services
• An affidavit is required to be given to the telephone company whenever digital terminal equipment
without encoded analog content and billing protection is used to transmit digital signals containing
encoded analog content which are intended for eventual conversion into voiceband analog signals and
transmitted on the network.
• The affidavit shall affirm that either no encoded analog content or billing information is being
transmitted or that the output of the device meets Part 68 encoded analog content or billing protection
specifications.
• End user/customer will be responsible for filing an affidavit with the local exchange carrier when
connecting unprotected customer premise equipment (CPE) to 1.544 Mbps or subrate digital services.
• Until such time as subrate digital terminal equipment is registered for voice applications, the affidavit
requirement for subrate services is waived.
8
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
Affidavits
Affidavit for Connection Of Customer Premises Equipment to 1.544 Mbps And/or Subrate Digital
Services
For the work to be performed in the certified territory of ___________________(telco name)
State of ________________
County of ________________
I, _______________________ (name), _____________________________(business address),
____________________ (telephone number) being duly sworn, state:
I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544 Mbps and/or ________ subrate
digital services. The terminal equipment to be connected complies with Part 68 of the FCC rules except for the encoded analog content and
billing protection specifications. With respect to encoded analog content and billing protection:
( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the digital CPE with respect to
analog content and encoded billing protection information continuously complies with Part 68 of the FCC Rules and
Regulations.
( ) The digital CPE does not transmit digital signals containing encoded analog content or billing information which is intended to
be decoded within the telecommunications network.
( ) The encoded analog content and billing protection is factory set and is not under the control of the customer.
I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, maintenance, and adjustment of the
encoded analog content and billing information has (have) been trained to perform these functions by successfully having completed one
of the following (check appropriate blocks):
( ) A training course provided by the manufacturer/grantee of the equipment used to encode analog signals; or
( ) A training course provided by the customer or authorized representative, using training materials and instructions provided by
the manufacturer/grantee of the equipment used to encode analog signals; or
( ) An independent training course (e.g., trade school or technical institution) recognized by the manufacturer/grantee of the
equipment used to encode analog signals; or
( ) In lieu of the preceding training requirements, the operator(s)/maintainer(s) is (are) under the control of a supervisor trained in
accordance with _________ (circle one) above.
I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate compliance with the information as
provided in the preceding paragraph, if so requested.
_________________________________Signature
_________________________________Title
_________________________________ Date
Transcribed and sworn to before me
This ________ day of _______________, _______
_________________________________
Notary Public
My commission expires:
_________________________________
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
9
Warranty and Customer Service
Total Access 900 Series Hardware Installation Guide
Warranty and Customer Service
ADTRAN will repair and return this product within the warranty period if it does not meet its published
specifications or fails while in service. Warranty information can be found at: http://support.adtran.com
(Click on Warranty and Repair Information, under Support.)
Product Registration
Registering your product helps ensure complete customer satisfaction. Please take time to register your
products on line at http://support.adtran.com. Click on Service/Support and then on Product Registration
under Support.
Product Support Information
A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service,
RMA requests, training, or more information, use the following contact information:.
Repair and Return
If you determine that a repair is needed, please contact our Customer and Product Service (CaPS)
department to have an RMA number issued. CaPS should also be contacted to obtain information
regarding equipment currently in house or possible fees associated with repair.
CaPS Department
(256) 963-8722
Identify the RMA number clearly on the package (below address), and return to the following address:
ADTRAN Customer and Product Service
901 Explorer Blvd. (East Tower)
Huntsville, Alabama 35806
RMA # _____________
10
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
Product Support Information
Pre-Sales Inquiries and Applications Support
Your reseller should serve as the first point of contact for support. If additional pre-sales support is needed,
the ADTRAN Support website provides a variety of support services such as a searchable knowledge base,
latest product documentation, application briefs, case studies, and a link to submit a question to an
Applications Engineer. All of this, and more, is available at:
http://support.adtran.com
When needed, further pre-sales assistance is available by calling our Applications Engineering
Department.
Applications Engineering (800) 615-1176
Post-Sale Support
Your reseller should serve as the first point of contact for support. If additional support is needed, the
ADTRAN Support website provides a variety of support services such as a searchable knowledge base,
updated firmware releases, latest product documentation, service request ticket generation and troubleshooting tools. All of this, and more, is available at:
http://support.adtran.com
When needed, further post-sales assistance is available by calling our Technical Support Center. Please
have your unit serial number available when you call.
Technical Support
(888) 4ADTRAN
International Technical Support
1-256-963-8716
Installation and Maintenance Support
The ADTRAN Custom Extended Services (ACES) program offers multiple types and levels of installation
and maintenance services which allow you to choose the kind of assistance you need. This support is
available at:
http://support.adtran.com
For questions, call the ACES Help Desk.
ACES Help Desk
61210916L1-34A
(888) 874-ACES (2237)
Copyright © 2005 ADTRAN, Inc.
11
Product Support Information
Total Access 900 Series Hardware Installation Guide
Training
The Enterprise Networks (EN) Technical Training Department offers training on our most popular
products. These courses include overviews on product features and functions while covering applications
of ADTRAN's product lines. ADTRAN provides a variety of training options, including customized
training and courses taught at our facilities or at your site. For more information about training, please
contact your Territory Manager or the Enterprise Training Coordinator.
12
Training Phone
(800) 615-1176, ext. 7500
Training Fax
(256) 963-6700
Training Email
training@adtran.com
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Table of Contents
Introduction to the Total Access 900 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Features and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Unpack and Inspect the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Contents of ADTRAN Shipments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Reviewing the Front Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Reviewing the Rear Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Rear Panel Interfaces and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Rackmounting Total Access 900 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Grounding for AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Supplying Power to the Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Total Access 900 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Battery Backup Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Unpack and Inspect the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Battery Pack Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
ADTRAN OS Supported MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
13
Table of Contents
14
Total Access 900 Series Hardware Installation Guide
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Total Access 900 Series Front Panel Layouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total Access 900 Series Rear Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voice Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wallmounting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Pack Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
21
23
24
26
30
15
List of Figures
16
Total Access 900 Series Hardware Installation Guide
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
List of Tables
Table 1.
Table 2.
Table A-1.
Table A-2.
Table A-3.
Table A-4.
Table A-5.
Table B-1.
Table B-2.
Table B-3.
Total Access 900 Series LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Pack Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VOICE Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSX-1 (T1 0/2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NET (T1 0/1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ETH 0/1 (10/100BaseT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CRAFT Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MIBs Supported in the AOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes Regarding MIB Exclusions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Traps Supported in the AOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
22
31
33
34
34
34
35
37
38
41
17
List of Tables
18
Total Access 900 Series Hardware Installation Guide
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
1.
INTRODUCTION TO THE TOTAL ACCESS 900 SERIES
The Total Access 900 Series products are Integrated Access Devices (IAD) designed for cost-effective
deployment of up to 1.536 Mbps of Session Initiation Protocol (SIP), PPP, or Frame Relay voice and data
services. The Total Access 900 Series combines voice and data services into a single platform creating the
4th generation of ADTRAN IADs for IP Telephony service providers (such as CLECs, ILECs, and ISPs).
Total Access 900 Series products are built on the ADTRAN Operating System (AOS) platform and include
the AOS built-in IP router and firewall features. The units include a network interface
(NET T1 0/1), a DSX-1 interface (T1 0/2), a VOICE interface (up to 24 FXS ports), a 10/100BaseT
interface, and a CRAFT port (management interface). An optional battery backup is also available for the
Total Access 900 Series. The last two digits of the product name indicate the number of on-board FXS
ports. The Total Access 912 contains twelve FXS ports, the Total Access 916 contains sixteen FXS ports,
and the Total Access 924 contains twenty-four FXS ports. The units can provision, test, and provide status
for any of the voice and data interfaces. All connections are made via the rear panel.
In common packet-based applications, the WAN (NET T1 0/1) connects to the ISP or Carrier’s network and
transmits packetized voice and data over a SIP trunk. The customer’s voice is presented as TDM to the
FXS ports or DSX-1 interface, and the data is routed out the LAN (ETH 0/1).
Features and Specifications
The Total Access 900 Series products have the following features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Support for up to 24 FXS ports with octal FXS daughter board
Support for a single DS-1 interface and a single DSX-1 interface
Support for a single auto MDI/MDX 10/100 Ethernet port (RJ-48C)
Full-featured AOS IP router/firewall
QOS/NAT/DHCP client, server, and relay
Support for SIP trunks
Support for up to 1.536 Mbps of Frame Relay or PPP
Support for Caller ID, Message Waiting, and stutter dial tone
Fax and analog modem compatible (V.90)
Support for local station to station calls
Up to 26 channels of G.711 (µ-law)
Up to 26 channels on G.729
Up to 26 channels of DTMF detection/generation
Support for 8 ms Echo Cancellation
Support for up to 26 channels of Caller ID
100 ms jitter buffer per channel
User-friendly web GUI and a familiar CLI interface
LEDs for system status information
Chassis dimensions: 1.75 inches H x 17.0 inches W x 8.5 inches D
AC power information: 90-120 VAC 60 Hz
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
19
Introduction to the Total Access 900 Series
Total Access 900 Series Hardware Installation Guide
This hardware installation guide describes the Total Access 900 Series units, details basic functionality,
gives installation instructions, and lists unit specifications. For more information on a specific application,
refer to the quick start documents provided on your ADTRAN OS Documentation CD.
The Total Access 900 SeriesSystem is intended to be installed, maintained, and
serviced by qualified personnel only.
Unpack and Inspect the System
Each Total Access 900 Series unit is shipped in its own cardboard shipping carton. Open the carton
carefully and avoid deep penetration into the carton with sharp objects.
After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in
transit, immediately file a claim with the carrier and contact ADTRAN Customer and Product Service (see
Customer Service, Product Support Information, and Training, on page 10).
Contents of ADTRAN Shipments
Total Access 912
Shipments of the Total Access 912 include the following items:
• Total Access 912
• Documentation CD or Reference sheet
• IEC 3-prong power cord
• Two brackets and six screws for wallmounting
Total Access 916
Shipments of the Total Access 916 include the following items:
• Total Access 916
• Documentation CD or Reference sheet
• IEC 3-prong power cord
• Two brackets and six screws for wallmounting
Total Access 924
Shipments of the Total Access 924 include the following items:
• Total Access 924
• Documentation CD or Reference sheet
• IEC 3-prong power cord
• Two brackets and six screws for wallmounting
20
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
2.
Physical Description
PHYSICAL DESCRIPTION
Reviewing the Front Panel Design
Figure 1 shows the Total Access 900 Series products front panels (the Total Access 912 contains twelve
FXS ports, the Total Access 916 contains sixteen FXS ports, and the Total Access 924 contains twentyfour FXS ports).
TOTAL ACCESS 912
Total Access 912
TOTAL ACCESS 916
Total Access 916
TOTAL ACCESS 924
Total Access 924
Figure 1. Total Access 900 Series Front Panel Layouts
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
21
Physical Description
Total Access 900 Series Hardware Installation Guide
Front Panel LEDs
Table 1 describes the front panel LEDs.
Table 1. Total Access 900 Series LEDs
For these
LEDs…
This activity…
Indicates that…
Off
Bootstrap mode - The boot code cannot be booted. During
Bootstrap mode, VOICE, DATA, NET, and DSX-1 LEDs will be
red.
Green (flashing)
Unit is powering up. On power-up the STATUS LED flashes
rapidly for 5 seconds, during which time the user may escape to
Bootstrap mode from the CRAFT port.
Green (solid)
Power is on and the unit is functioning normally.
Off
No power.
Green
AC power is operational.
Amber
AC power has failed. Battery backup is active.
Off
All ports are inactive.
Green (solid)
At least one port is off-hook.
Green (flashing)
At least one port is ringing.
Amber
At least one port is in test.
Red
Fault condition.
Off
Administratively shut down.
Green
Layer 2 is up on the NET interface.
Red
Layer 2 is down on the NET interface.
Off
Port is administratively shut down.
Green
Link is up and in normal operation.
Amber
Port is in test.
Red
An alarm condition is present.
Off
Link is down or port is administratively shut down.
Green
10BaseT link is up.
Amber
100BaseT link is up.
Off
No traffic or port is administratively shut down.
Green (flashing)
Data traffic is flowing.
ETH 0/1
Green (off)
Link is down or port is administratively shut down.
(Rear Panel)
Green (solid)
Link is up.
Amber (off)
No traffic or port is administratively shut down.
Amber (flashing)
Data traffic is flowing.
STATUS
POWER
VOICE
DATA
NET / DSX-1
LINK
TD / RD
22
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
Physical Description
Reviewing the Rear Panel Design
Figure 2 shows the Total Access 900 Series products’ rear panel, which contain identical interfaces
regardless of the model (Total Access 912/916/924).
Figure 2. Total Access 900 Series Rear Panel Layout
Rear Panel Interfaces and LEDs
Power Supply
The Total Access 900 Series products have a 90-120 VAC power supply with an IEC connector. The
appropriate three-prong cable is included in the shipment. Please refer to 10/100BaseT Ethernet
Interface and Activity LEDs for connection details.
Battery Backup Connection
An optional battery backup system (P/N 1175044L1, 2, or 4) is available for the Total Access 900
Series products. Refer to the documentation available for your specific battery backup unit for more
information on this connection, or see Battery Backup Unit on page 29 for a more details.
CRAFT Interface
The CRAFT interface is an EIA-232 serial port (DCE) which provides for local management and
configuration (via a DB-9 female connector). Table A-5 on page 35 shows the CRAFT port pinouts.
Connection directly to an external modem requires a cross-over cable.
10/100BaseT Ethernet Interface and Activity LEDs
The Ethernet port (ETH 0/1) is an RJ-48C connector with LEDs. The amber activity LED flashes when
data traffic is being sent or received on the Ethernet port. The green link LED is on when the unit has a
good connection to the LAN. See Table A-4 on page 34 for the Ethernet port pinout.
Network Interface
The NET T1 0/1 interface is a DS-1 RJ-48C pin connection. See Table A-3 on page 34 for the network
interface pinout.
DSX-1 Interface
The DSX-1 T1 0/2 interface is a DSX-1 RJ-48C pin connection. See Table A-2 on page 34 for the
network interface pinout.
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
23
Physical Description
Total Access 900 Series Hardware Installation Guide
VOICE Connection
A single 50-pin female amphenol connector provides the interconnect wiring for the analog circuits
(FXS). Figure 3 shows the VOICE connector pinout.
25
50
24
49
23
48
22
47
21
46
20
45
19
44
18
43
17
42
16
41
15
40
14
39
13
38
12
37
11
36
10
35
9
34
8
33
7
32
6
31
5
30
4
29
3
28
2
1
27
26
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
NC
NC
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
Circuit 24
Circuit 23
Circuit 22
Circuit 21
Circuit 20
Circuit 19
Circuit 18
Circuit 17
Circuit 16
Circuit 15
Circuit 14
Circuit 13
Circuit 12
Circuit 11
Circuit 10
Circuit 9
Circuit 8
Circuit 7
Circuit 6
Circuit 5
Circuit 4
Circuit 3
Circuit 2
Circuit 1
50 PIN
AMP
RECEPTACLE
Figure 3. Voice Connector Pin Assignments
The Total Access 912 only uses circuits 1-12. The Total Access 916 only uses circuits 1-16.
The Total Access 924 uses all circuits (1-24).
24
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
3.
Unit Installation
UNIT INSTALLATION
The instructions and guidelines provided in this section cover hardware installation topics such as
wallmounting/rackmounting the unit and installing the unit. See Unpack and Inspect the System on page 20
before getting started. These instructions are presented as follows:
•
•
•
•
Tools Required on page 25
Mounting Options on page 26
Grounding Instructions on page 27
Supplying Power to the Unit on page 28
For information on configuration for a specific application, refer to the quick configuration documents
provided on your ADTRAN OS Documentation CD. For details on the command line interface, refer to the
AOS Command Reference Guide (also included on your CD).
To prevent electrical shock, do not install equipment in a wet location or during an
electrical storm.
Tools Required
The following customer-provided tools are required for the hardware installation of the Total Access 900
Series:
•
•
•
•
•
Two wood screws, 3/32-inch to 1/8-inch (1 1/2-inches length)
Drill and drill bit set
Screwdriver (medium)
25-pair male amphenol cable (customer connection)
Selected punch-down block and tool
To access the command line interface (CLI) of the Total Access 900 Series, you must have
a VT100 terminal or PC with terminal emulation software and a CRAFT port cable.
Instructions on how to access the CLI are given in the AOS Command Reference Guide
(provided on the ADTRAN OS Documentation CD).
To access the Web-Based GUI of the Total Access 900 Series, you must have a PC
connected to an IP network. Instructions on how to access the Web-Based GUI are given in
the Web GUI Configuration Guide, document number 61210916L1-42.1 (provided on the
ADTRAN OS Documentation CD).
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
25
Unit Installation
Total Access 900 Series Hardware Installation Guide
Mounting Options
The Total Access 900 Series may be installed in a wallmount, rackmount, or tabletop configuration. The
following sections provide step-by-step instructions for rackmounting and wallmounting.
Wallmounting Total Access 900 Series
Instructions for Wallmounting Total Access 900 Series
Step
Action
1
Attach the wallmount brackets to the unit using the supplied screws.
2
Decide on a location for the Total Access 900 Series. Keep in mind that the unit needs to be
mounted at or below eye level so that the LEDs are visible.
Warning! Do not mount the chassis with the LEDs facing up (see Figure 4).
3
Prepare the mounting surface by attaching a board (typically plywood, 3/4-inch to 1-inch thick)
to a wall stud. Important! Mounting to a stud ensures stability. Using sheetrock anchors may
not provide sufficient long-term stability.
4
Have an assistant hold the unit in position as you install two 3/32-inch up to 1/8-inch
(1 1/ 2-inch or greater length) wood screws through the unit’s brackets and into the mounted
board.
5
Proceed to the steps given in Grounding Instructions on page 27.
LEDs Pointing Down
Step 1: Prepare the
mounting surface by
attaching a board
(typically plywood, 3/4"
to 1" thick) to the wall.
(The board must be
attached to a stud in
the wall for stability.)
LEDs Pointing Sideways
Step 2: Wallmount the
Total Access 900 Series
unit using two 3/32" to
1/8" (1 1/2" or greater in
length) wood screws.
Figure 4. Wallmounting the Unit
26
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
Unit Installation
Rackmounting Total Access 900 Series
The Total Access 900 Series products are housed in a 1U-high, rackmountable chassis which can be
installed into 19-inch or 23-inch equipment racks. For a rackmount installation, optional rackmount
brackets must be purchased (19” – P/N 1200927L19, 23” – P/N 1200927L23).
The Total Access 912/916/924 mount and connect with standard fasteners and hand tools.
Follow these steps to rackmount the Total Access 912/916/924:
Instructions for Rackmounting Total Access 900 Series
Step
Action
1
Position the Total Access 900 Series in a stationary equipment rack. This unit takes up 1U of
space. To allow proper grounding, scrape the paint from the rack around the mounting holes
where the Total Access 900 Series will be positioned.
2
Have an assistant hold the unit in position as you install two mounting bolts through the unit’s
brackets and into the equipment rack.
3
Proceed to the steps given in Grounding Instructions on page 27.
Be careful not to compromise the stability of the equipment mounting rack when installing
this product.
Grounding Instructions
The following provides grounding instructions for the Underwriters’ Laboratory UL 60950 Standard for
Safety of Information Technology Equipment Including Electrical Business Equipment, with revisions
dated March 15, 2002.
A supplementary equipment grounding conductor shall be installed between the product or system and
ground that is in addition to the equipment grounding conductor in the power supply cord. The
supplementary equipment grounding conductor shall not be smaller in size than the ungrounded branchcircuit supply conductors. The supplementary equipment grounding conductor shall be connected to the
product at the terminal provided, and shall be connected to ground in a manner that will retain the ground
connection when the product is unplugged from the receptacle. The connection to ground of the
supplementary equipment grounding conductor shall be in compliance with the rules for terminating
bonding jumpers at Part K or Article 250 of the National Electrical Code, ANSI/NFPA 70. Termination of
the supplementary equipment grounding conductor is permitted to be made to building steel, to a metal
electrical raceway system, or to any grounded item that is permanently and reliably connected to the
electrical service equipment ground.
The supplemental grounding conductor shall be connected to the equipment using a number 8 ring terminal
and should be fastened to the grounding lug provided on the rear panel of the equipment. The ring terminal
should be installed using the appropriate crimping tool (AMP P/N 59250 T-EAD Crimping Tool or
equivalent).
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
27
Unit Installation
Total Access 900 Series Hardware Installation Guide
Grounding for AC Power
The attachment-plug receptacles in the vicinity of the product or system are all to be of a grounding type,
and the equipment grounding conductors serving these receptacles are to be connected to earth ground at
the service equipment.
Supplying Power to the Unit
As shipped, each Total Access 900 Series product is set to factory default conditions. After installing the
unit, the Total Access 900 Series product is ready for power-up. To power the unit, ensure that the unit is
properly connected to an appropriate power source (as outlined in the sections below).
Total Access 900 Series
The Total Access 900 Series comes equipped with a 90 -120 VAC, 60 Hz power supply. The maximum
power consumption is 50 W. A grounded, three-plug detachable cable is included with the shipment.
28
•
•
•
Use only copper conductors when making power connections.
Install unit in accordance with Article 400 and 364.8 of the NEC NFPA 70.
A readily accessible disconnect device, that is suitably approved and rated, shall be
incorporated in the field wiring.
•
Maximum recommended ambient operating temperature is 50°C.
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
4.
Battery Backup Unit
BATTERY BACKUP UNIT
The ADTRAN Battery Backup Unit is an optional device designed as a backup DC power supply for the
Total Access 900 Series. The Battery Pack connects to the Total Access 900 Seriesthrough a 6-foot charge/
discharge, 2-conductor wire with a keyed modular plug (included with the Battery Backup Unit). The
1175044L1 Battery Backup Unit is a low profile wallmount configuration. It can be rackmounted with the
appropriate 19-inch or 23-inch rackmount adapter brackets. The 1175044L2 is an equivalent Battery
Backup Unit with a hinged front access door.
Features
Features of the Battery Pack, P/N 1175044L1/L2, include the following:
•
•
•
•
•
•
No-spill battery design
Compact wallmount or rackmount box
Double Battery Pack rackmounting available
7 A/hr batteries (up to 8 hours of backup, depending on load)
Modular plug (provides quick and easy installation)
All mounting hardware included
Unpack and Inspect the Battery Pack
Removing the Battery Pack covers could allow batteries to fall out.
After unpacking the Battery Pack unit, inspect it for damage. If damage is noted, file a claim with the
carrier; then contact ADTRAN Customer Service (see page 10).
The Battery Pack weighs in excess of 30 pounds. Arrange for assistance when
handling the Battery Pack for mounting.
Batteries are retained and pre-wired in the Battery Pack in a specific pattern. Battery position is maintained
by foam spacers press-fitted against the housing walls. Removing batteries or disconnecting wires
compromises correct reassembly and should not be attempted.
Battery Pack Safety Notices
The Battery Pack should only be used in specified ADTRAN applications.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
29
Battery Backup Unit
Total Access 900 Series Hardware Installation Guide
• This device may not cause harmful interference
• This device must accept any interference received, including that which may cause undesired operation
Wallmounting the Battery Pack
Figure 5 shows the Battery Pack mounting dimensions.
Figure 5. Battery Pack Mounting Dimensions
For a wallmount installation, the Battery Pack installs on heavy plywood (3/4-inch minimum) using four
#10 x 3/4-inch pan-head wood screws. Install the Battery Pack as follows:
Wallmount Installation
Step
Action
1.
Determine the preferred unit layout to ensure cable plugs reach their designated sockets.
2.
Ensuring a plumb measurement, mark where the pilot holes are to be drilled according to the
dimensions given in the documentation included with your shipment.
3.
Drill all four pilot holes using a size 1/16-inch drill bit.
4.
Screw in the top two pan-head screws that fit the keyhole openings. Let the head of each
screw protrude 1/16 inch from the plywood to engage the keyhole slot.
Do not let the weight of the Battery Pack rest on the two keyhole screws. Maintain
support until the lower two screws are fully inserted.
5.
With an assistant, lift the Battery Pack and position to engage the screw heads. Allow the pack
to slide down until the slot end rests against the screws.
6.
Insert the two lower screws through the tabs and tighten securely.
7.
Use cable tie-downs as appropriate. The Total Access 900 Series battery connection from the
Battery Pack should be directly connected to the BATT port on the rear of the chassis.
30
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
Battery Backup Unit
Maintenance
• The Battery Pack does not require routine maintenance for normal operation. The life expectancy
of the Battery Pack is 3 to 5 years on standby use when used at room temperature.
•
Excessive heat decreases battery power and life. Ideal ambient temperature for battery life and
capacity is 20°C. Extreme low temperature also decreases battery capacity.
•
Battery shelf life is extended in cooler temperatures.
•
To order replacement batteries, reference the following part number: 1975044L1 (12 V replacement
batteries).
ADTRAN is an environmentally-friendly company. Therefore, we encourage the proper recycling and
handling of the batteries. Federal and state laws prohibit the improper disposal of all lead acid batteries.
The customer is responsible for the handling of their batteries from the day of purchase through their
ultimate disposal. For more information on battery replacement and recycling, reference ADTRAN
document number 60000120-36 online at www.adtran.com. (Enter the document number in the search
field to display a link to the document.)
Specifications
Table 2 provides Battery Pack specifications.
Table 2. Battery Pack Specifications
Battery
Part Number:
Suppliers:
Batteries:
Voltage:
Backup Time:
Wire Gauge:
311212V02
YUASA and Panasonic
7 A/hr per battery
-12 VDC per battery
Up to 8 hours
18 AWG
Environmental
Operating Temperatures:
Preferred:
Charge:-15°C to 50°C
Discharge: -20°C to 60°C
20°C
Physical
Dimensions:
Weight:
61210916L1-34A
17 inches W x 6.5 inches H x
3.5 inches D
30 lb.
Copyright © 2005 ADTRAN, Inc.
31
Battery Backup Unit
32
Total Access 900 Series Hardware Installation Guide
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Appendix A.
PIN ASSIGNMENTS
Table A-1. VOICE Connector
Pins
50-pin
Amphenol
Connector
1, 26
Circuit 1
FXS 0/1 Ring, Tip
2, 27
Circuit 2
FXS 0/2 Ring, Tip
3, 28
Circuit 3
FXS 0/3 Ring, Tip
4, 29
Circuit 4
FXS 0/4 Ring, Tip
5, 30
Circuit 5
FXS 0/5 Ring, Tip
6, 31
Circuit 6
FXS 0/6 Ring, Tip
7,32
Circuit 7
FXS 0/7 Ring, Tip
8,33
Circuit 8
FXS 0/8 Ring, Tip
9, 34
Circuit 9
FXS 0/9 Ring, Tip
10, 35
Circuit 10
FXS 0/10 Ring, Tip
11, 36
Circuit 11
FXS 0/11 Ring, Tip
12, 37
Circuit 12
FXS 0/12 Ring, Tip
13, 38
Circuit 13
FXS 0/13 Ring, Tip
14, 39
Circuit 14
FXS 0/14 Ring, Tip
15, 40
Circuit 15
FXS 0/15 Ring, Tip
16, 41
Circuit 16
FXS 0/16 Ring, Tip
17, 42
Circuit 17
FXS 0/17 Ring, Tip
18, 43
Circuit 18
FXS 0/18 Ring, Tip
19, 44
Circuit 19
FXS 0/19 Ring, Tip
20, 45
Circuit 20
FXS 0/20 Ring, Tip
21, 46
Circuit 21
FXS 0/21 Ring, Tip
22, 47
Circuit 22
FXS 0/22 Ring, Tip
23, 48
Circuit 23
FXS 0/23 Ring, Tip
24, 49
Circuit 24
FXS 0/24 Ring, Tip
25, 50
61210916L1-34A
--
Description
NC
Copyright © 2005 ADTRAN, Inc.
33
Appendix A
Total Access 900 Series Hardware Installation Guide
Table A-2. DSX-1 (T1 0/2)
Pin
Name
Description
1
R
Transmit data toward the DTE (Ring)
2
T
Transmit data toward the DTE (Tip)
3
Unused
—
4
R1
Receive data from the DTE (Ring)
5
T1
Receive data from the DTE (Tip)
6-8
Unused
—
Table A-3. NET (T1 0/1)
Pin
Name
Description
1
R1
Receive data from the network (Ring)
2
T1
Receive data from the network (Tip)
3
Unused
—
4
R
Transmit data toward the network (Ring)
5
T
Transmit data toward the network (Tip)
6-8
Unused
—
Table A-4. ETH 0/1 (10/100BaseT)
Pin
34
Name
Description
1
TX1
Transmit Positive
2
TX2
Transmit Negative
3
RX1
Receive Positive
4,5
—
Unused
6
RX2
Receive Negative
7, 8
—
Unused
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
Appendix A
Table A-5. CRAFT Port
Pin
Name
Description
1
DCD
Data Carrier Detect (output)
2
RD
Receive Data (output)
3
TD
Transmitted Data (input)
4
DTR
Data Terminal Ready (input)
5
GND
Ground - connected to unit chassis
6
DSR
Data Set Ready (output)
7
RTS
Request To Send - flow control (input)
8
CTS
Clear To Send - flow control (output)
9
RI
Ring Indicate (output)
Connection directly to an external modem requires a cross-over cable.
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
35
Appendix A
36
Total Access 900 Series Hardware Installation Guide
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
APPENDIX A.
ADTRAN OS SUPPORTED MIBS
ADTRAN AOS platforms support the MIBs listed in Table B-1. For the most up-to-date MIB list, please visit our
website at www.adtran.com.
Table B-1. MIBs Supported in the AOS
Name
RFC
DS1-MIB
2495
Describes DS1, E1, DS2, and E2 interface objects.
1
Ether-like-MIB
2665
Describes generic objects for Ethernet-like network
interfaces.
2
FRAME-RELAY-DTE-MIB
2115
Describes the use of a Frame Relay interface by a DTE.
3
IF-MIB
2863
Describes generic objects for network interface sub-layers.
4
MAU-MIB
2668
Management information for 802.3 Media Access Units
(MAU or transceiver).
5
SNMPv2-MIB
1907
The MIB module for SNMPv2 entities.
6
IP-MIB
2011
Describes IP and ICMP implementations, excluding the
management of IP routes.
7
IP-FORWARD-MIB
2096
Describes CIDR multi-path IP Routes.
8
ADTRAN-AOS-VOICE-MIB
ADTRAN-AOS-MUX-MIB
ADTRAN-AOS-Media-Gateway-MIB
Description
Notes
ADTRAN enterprise MIB, for general configuration of
various voice interface types.
ADTRAN enterprise MIB, for the management of AOS
products supporting TDM groups and/or cross-connects.
ADTRAN enterprise MIB, for the statistics pertaining to
VoIP and the units Media Gateway.
Standard MIBs are supported with the following exclusions. These exclusions were agreed upon at the time the MIBs
were implemented and represent objects that have been made obsolete or depreciated, or objects we simply do not
support at this time.
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
37
Appendix B
Total Access 900 Series Hardware Installation Guide
Table B-2. Notes Regarding MIB Exclusions
Note 1: DS1 exclusions
dsx1FarEndCurrentTable
dsx1FarEndIntervalTable
dsx1FarEndTotalTable
dsx1FracTable
Note 2: EtherLike exclusions
dot3StatsTable
•
dot3StatsSQETestErrors
•
dot3StatsEtherChipSet
dot3CollTable
dot3ControlTable
•
dot3ControlInUnknownOpcodes
dot3PauseTable
•
dot3InPauseFrames
•
dot3OutPauseFrames
Note 3: FRAME-RELAY-DTE exclusions
frDlcmiTable
•
frDlcmiAddress
•
frDlcmiAddressLen
•
frDlcmiMulticast
frCircuitTable
•
frCircuitExcessBurst (set not allowed)
•
frCircuitLogicalIfIndex (set not allowed)
•
frCircuitRowStatus
frErrTable
frTrapState
frTrapMaxRate
Note 4: IF exclusions
IfTable
•
ifInNUcastPkts
•
ifOutNUcastPkts
•
ifOutQLen
•
ifSpecific
ifXTable
•
ifHCInUcastPkts
•
ifHCInMulticastPkts
•
ifHCInBroadcastPkts
•
ifHCOutUcastPkts
•
ifHCOutMulticastPkts
•
ifHCOutBroadcastPkts
ifStackTable
ifTestTable
IfRcvAddressTable
38
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
Appendix B
Table B-2. Notes Regarding MIB Exclusions (Continued)
Note 5: MAU exclusions
rpMauTable
rpJackTable
broadMauBasicTable
Note 6: SNMPv2 exclusions
sysORLastChange
sysORTable
snmpOutPkts
snmpInTooBigs
snmpInNoSuchNames
snmpInBadValues
snmpInReadOnlys
snmpInGenErrs
snmpInTotalReqVars
snmpInTotalSetVars
snmpInGetRequests
snmpInGetNexts
snmpInSetRequests
snmpInGetResponses
snmpInTraps
snmpOutTooBigs
snmpOutNoSuchNames
snmpOutBadValues
snmpOutGenErrs
snmpOutGetRequests
snmpOutGetNexts
snmpOutSetRequests
snmpOutGetResponses
snmpOutTraps
snmpTrapOID
snmpTrapEnterprise
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
39
Appendix B
Total Access 900 Series Hardware Installation Guide
Table B-2. Notes Regarding MIB Exclusions (Continued)
Note 7: IP exclusions
ipForwarding
ipDefaultTTL
ipInReceives
ipInHdrErrors
ipInAddrErrors
ipForwDatagrams
ipInUnknownProtos
ipInDiscards
Note 7: IP exclusions (Continued)
ipInDelivers
ipOutRequests
ipOutDiscards
ipOutNoRoutes
ipReasmTimeout
ipReasmReqds
ipReasmOKs
ipReasmFails
ipFragOKs
ipFragFails
ipFragCreates
ipNetToMediaTable
Note 8: IP-FORWARD exclusions
ipForwardNumber
ipForwardTable
ipCidrRouteNumber
40
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
Appendix B
Table B-3. Traps Supported in the AOS
Name
OID
Cold Start
1.3.6.1.6.3.1.1.5.1
Warm Start
1.3.6.1.6.3.1.1.5.2
Link Down
1.3.6.1.6.3.1.1.5.3
Link Up
1.3.6.1.6.3.1.1.5.4
Authentication Failure
1.3.6.1.6.3.1.1.5.5
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
41
Appendix B
42
Total Access 900 Series Hardware Installation Guide
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A
Total Access 900 Series Hardware Installation Guide
Index
INDEX
N
A
NET T1 0/1 23
pinout 34
AC power 28
affidavits 8
P
B
power 28
power supply 23
product registration 10
battery
backup unit 29
specifications 31
C
contents of shipment 20
craft port
EIA-232 serial port (DCE) 23
pinouts 35
customer service 10
D
DSX-1 (T1 0/2) 23
pinout 34
E
ethernet interface
10/100BaseT 23
pinout 34
exclusions (MIBs) 38
F
features of the Total Access 900 Series 19
front panel 21
R
rackmounting 27
rear panel 23
repair and return 10
S
safety instructions 4, 29
shipping contents 20
specifications
battery pack 31
Total Access 900 Series 19
T
tools required for installation 25
trademarks 2
traps 41
U
unit installation 25
unpacking and inspecting the system 20
the battery pack 29
V
grounding instructions 27
voice 24
pinout 24, 33
I
W
G
inspection 20
installation
general 25
rackmount 27
wallmount 30
installing 25
wallmounting 26
installation of battery pack 30
warranty 10
L
LEDs
front panel 22
rear panel 23
M
maintenance of Battery Pack 31
MIBs 37
mounting options 26
rack 27
wall 26
61210916L1-34A
Copyright © 2005 ADTRAN, Inc.
43
Index
44
Total Access 900 Series Hardware Installation Guide
Copyright © 2005 ADTRAN, Inc.
61210916L1-34A