advertisement
Two-Way Ceiling Speaker Pairs
NEW!
All models feature a polypropylene cone woofer with rubber surround, coupled with a 1 ⁄
2
" polymer dome tweeter for very good sound performance for the dollar. White ABS frame and micro perforated grill compliments any décor and is easily mounted to any ceiling without the need for additional hardware. Features:
•6dB/octave crossover (#50-14000 high pass tweeter capacitor only)
•8ohm impedance •Color coded push terminals accept up to 14AWG cable •Sold in pairs
Order #
50-14000
50-14005
50-14010
50-14015
Speaker
Size
4"
5.25"
6.5"
8"
Power Capacity
RMS/peak
20W/35W
25W/50W
30W/60W
40W/80W
Frequency
Response
50Hz~20KHz
45Hz~20KHz
45Hz~20KHz
30Hz~20KHz
Overall
Diameter
6.73"
7.95
9.02"
10.71
Required
Cutout
5.39"
6.46
7.60
9.29"
MSRP
$44.95
59.95
64.95
89.95
AUDIO/VIDEO
Whole House Audio
ONLY
$20 .49
23 .49
25 .49
30 .49
Section
01
Ceiling Speakers . . . . . . . . . . . . . . . . . . . . . . 5~7, 9, 18
In Wall Speakers . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7, 9
MCM Custom Audio . . . . . . . . . . . . . . . . 5, 11~15, 18, 19
Stellar Labs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5~7, 11
Speco Technologies . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Channel Vision . . . . . . . . . . . . . . . . . . . . . . . . 8, 10, 15
A-Bus Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Amplifiers . . . . . . . . . . . . . . . . . . . . . . . . . . 10~12, 14
Speaker Selectors . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Breathe Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
IR Remote Distribution . . . . . . . . . . . . . . . . . . . . . 15~17
Knoll Systems . . . . . . . . . . . . . . . . . . . . . . . . . 9, 10, 16
Outdoor Speakers . . . . . . . . . . . . . . . . . . . . . . . . 18, 19
Yorkville . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Speakercraft . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 17
LCD Video Monitors . . . . . . . . . . . . . . . . . . . . . . . . . .20
Pyle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 20~22
Equalizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Volume Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 18
Sherwood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
6
1
⁄
2
" Single Point Stereo™ Ceiling Speaker
Intended for small areas that do not justify installation of two speakers, this single stereo speaker provides both left and right audio channels from a single point.
Features: •Two independent 6dB/octave crossover channels •Dual 1 ⁄
2
" polymer dome tweeters •Dual voice coil 6 1 ⁄
2
" woofer •Polypropylene cone woofer •Rubber surround •Micro perforated grill Specifications: •Power capacity: 50W RMS per channel •Frequency response:
35Hz~20KHz •Impedance: 8ohm per channel •Overall frame diameter: 9.01" •Required cutout: 7.60"
•Mounting depth: 2.91" •Sold individually
NEW!
Order #
50-14020
MSRP
$44.95
ONLY
$18 .49
Ceiling Mount Speaker Pair
4 Efficient dual cone design
4 Round ceiling mount
Low cost dual cone speaker pair is ideal for background music, paging and general audio applications. White plastic frame and painted steel grill compliments any decor. Attached mounting brackets easily mount in ceiling or wall board without additional hardware. 8ohm. Sold in pairs.
Order #
50-6240
50-6241
50-6242
Speaker Power Capacity Frequency
Size
5 1
6 1 ⁄
⁄
8"
4
2
"
"
RMS/Peak
15W/30W
15W/30W
20W/40W
Response SPL
Overall Frame Cutout Mounting
Diameter
110Hz~20KHz 90dB 8"
100Hz~18KHz 90dB 9"
80Hz~20KHz 91dB 10 3 ⁄
4
"
Hole
6 1
7 1 ⁄
9 3 ⁄
⁄
2
2
8
"
"
"
Depth
2 1
2
2 5 ⁄
3 3 ⁄
⁄
8
8
"
"
"
MSRP ONLY
$44.95 $34 .49
59.95 45 .49
74.95 56 .99
Impedance Matching Volume Controls
•These in-wall volume controls utilize high quality multitap audio transformers and feature a smooth 12 position rotary switch
•Designed for use in distributed audio systems, the impedance matching feature of these volume controls allow for the connection of up to 16 pairs of speakers to a single amplifier, and appear as a
4ohm load Features: •Detachable terminal strips accept up to
14AWG wire •May be mounted in a single gang box or low voltage bracket •Matching decora wall plates included Specifications:
•Frequency response: 35Hz~20KHz •Attenuation: -34~0dB, in 12 steps •Impedance matching: x2, x4 and x 8ohm
Order #
50-7820
50-7821
50-7822
50-7823
50-7840
50-7841
50-7842
50-7843
Color
White
Ivory
Almond
Black
White
Ivory
Almond
Black
Power Capacity (RMS/Max)
25W/100W
25W/100W
25W/100W
25W/100W
100W/300W
100W/300W
100W/300W
100W/300W
ONLY
$29 .99
29 .99
29 .99
29 .99
39 .99
39 .99
39 .99
39 .99
Compact Ceiling Speaker System
4 Mounts in standard round ceiling box
4 Aluminum cone
4 Rubber surroud
Rugged 2
1
⁄
2
" driver is mounted in an attractive round faceplate that is compatible with commonly available ceiling fan electrical boxes, such as the B618R series from Carlon (MCM #28-17060). Specifications: •Power capacity: 20W/30W RMS/peak •Frequency response:
100Hz~20KHz •Sensitivity: 85dB (W/M) •Nominal impedance: 8ohm •Front panel diameter: 5
•Mounting depth: 1
3
⁄
4
" •Sold individually
3
⁄
8
"
Order #
50-9045
MSRP
$59.95
(1-3)
$39 .99
(4-up)
$36 .83
NEW!
Amplified
In-Wall
NEW!
Volume Control
Unique in-wall volume control fits amazingly in a single gang electrical box, yet houses a powerful 50W RMS amplifier. It is perfect for simple self contained audio in a single room, expanding a system to add another zone, or adding to an existing system to play a local source.
Highly efficient Class D amplifier accepts standard line level input, and provides 25W RMS x 2CH, with full
20Hz ~ 20KHz response. Separately available DC power supply allows power to be applied from a remote location, increasing installation flexibility. Rotary encoder provides noise free control and five segment
LED display indicates ON/OFF status and volume setting. Power and speaker connections are stripped tinned leads, L:/R inputs are RCA female.
Order #
50-7830
50-7835
Description
Volume control
15VDC, 4A power supply
ONLY
$116 .00
57 .56
www.
MCM electronics.com
.
/
1-800-543-4330 5
Section
01
AUDIO/VIDEO
Whole House Audio
Contractor Series In-Wall and Ceiling Speakers
This cost effective series of architectural speaker systems are designed to provide very good sound performance for the cost. Despite their “entry level” position in the Stellar Labs ® line-up, these speakers match performance of others mid level and even some premium installed systems. Installation in existing wallboard is fast and easy using proven rotating plastic clips. And using a connection method borrowed from the commercial sound industry, detachable screw terminal strips greatly ease installation while providing a far superior connection to push terminals. Features: •Polypropylene cone woofer with butyl rubber surround •Pivoting silk dome tweeter •6dB/octave crossover •Rust proof perforated aluminum grill •Detachable phoenix style connector •Ceiling and in-wall speakers are sold in pairs, center channel speaker is sold individually
Dual 5
1
⁄
4
" In-Wall
Center Channel Speaker
Intended for use in home theater installations as a horizontal center channel speaker, this dual woofer system is also perfectly suitable in vertical arrangement as a front or rear speaker in the home theater, as well as whole house distributed audio. Shielded woofers solve issues with older CRT monitors, and independent high and low frequency compensation enable tailoring to the individual environment. Features: •Dual 5 1 ⁄
4
" poly cone woofers with rubber surrounds •1" pivoting silk dome tweeter •Treble compensation selector +/0/–3dB •Bass compensation selector +/0/–3dB •Microperforated aluminum grill Specifications: •Power capacity:
55W/80W RMS/peak •Frequency response:
60Hz~22KHz (±3dB) •Sensitivity: 90dB (W/M)
•Impedance: 8ohm Mounting: •Overall frame: 7 1 ⁄
2
" (H) x 16 5 ⁄
8
" (W) •Required cutout: 5 1 ⁄
2
" (H) x 15" (W)
•Depth: 3 1 ⁄
2
" •Sold individually
Order # MSRP
50-10520 $99.00
Replacement Grill (sold individually)
50-13640 -
ONLY
$56.99
8.98
8" Single
Point Stereo
Ceiling
Speaker
Intended for small areas that do not justify installation of two speakers, this single stereo speaker provides both left and right audio channels, from a single point. Two independent crossover channels, two separately mounted tweeters, and a dual voice coil woofer provide an outlet for both left and right channels, from one 8" mounted speaker. It is perfect in entryways, bathrooms, hallways and similar areas for background or foreground music in whole house distributed audio and home theater environments.
8" Single Point Stereo Ceiling Speaker
•Provides both left and right audio channels
•Dual 3 ⁄
4
" pivoting silk dome tweeters
•Power capacity: 40W/60W RMS/peak per channel
•Frequency response: 50Hz~22KHz (±3dB)
•Impedance: 8ohm per channel
•Sold individually
Order # MSRP
50-10580 $119.00
Replacement Grill (sold individually)
50-13636 -
ONLY
$68.49
8.57
6
1
⁄
2
" Single Point Stereo Ceiling Speaker
•Provides both left and right audio channels
•Dual 3 ⁄
4
" pivoting silk dome tweeters
•Power capacity: 35W/50W RMS/peak per channel
•Frequency response: 55Hz~22KHz (±3dB)
•Impedance: 8ohm per channel
•Sold individually
Order # MSRP
50-10581 $119.00
Replacement Grill (sold individually)
50-13635 -
ONLY
$62.49
7.06
6
1
⁄
2
" Ceiling Speaker Pair
Popular size ceiling speaker is perfect for background or foreground music in whole house distributed audio and home theater environments. Their low cost also makes them suitable in large scale commercial music and paging environments. The mounting frame has a 30° offset, allowing proper aim when mounted close to walls and corners. Features: •6 1 ⁄
2
" poly cone woofer with rubber surround •1" pivoting silk dome tweeter •Cloth backed micro-perforated aluminum grill Specifications:
•Power capacity: 40W/60W RMS/peak •Frequency response: 65Hz~20KHz (±3dB) •Sensitivity: 88dB
(W/M) •Impedance: 8ohm Mounting: •Overall frame:
9.375" (dia) •Required cutout: 8.10" (dia)
•Depth: 5" •Speaker system is sold in pairs
Order # MSRP
50-10510 $119.00
Replacement Grill (sold individually)
50-13636 -
ONLY
$68.49
7.06
6
1
⁄
2
" In-Wall Speaker Pair
Compact in–wall speaker is perfect for background or foreground music in whole house distributed audio and as front or rear speakers in home theater environments. Their low cost also makes them suitable in large scale commercial music and paging environments. Features: •6 1 ⁄
2
" poly cone woofer with rubber surround •1" pivoting silk dome tweeter •Cloth backed micro-perforated aluminum grill Specifications:
•Power capacity: 40W/60W RMS/peak •Frequency response: 65Hz~20KHz (±3dB) •Sensitivity: 88dB
(W/M) •Impedance: 8ohm Mounting: •Overall frame:
12" (H) x 8.25" (W) •Required cutout: 10.25" (H) x
6.5" (W) •Depth: 3" •Speaker system is sold in pairs
Order # MSRP ONLY
50-10500 $119.00
Replacement Grill (sold individually)
50-13630 -
$68.49
6.86
8" Ceiling Speaker Pair
Full size ceiling speaker is perfect for background or foreground music in whole house distributed audio and home theater environments. Their low cost also makes them suitable in large scale commercial music and paging environments. The mounting frame has a 30° offset, allowing proper aim when mounted close to walls and corners. Features: •8" poly cone woofer with rubber surround •1" pivoting silk dome tweeter •Microperforated aluminum grill Specifications: •Power capacity: 80W/55W RMS/peak •Frequency response:
60Hz~20KHz (±3dB) •Sensitivity: 89dB (W/M)
•Impedance: 8ohm Mounting: •Overall frame:
11.5" (dia) •Required cutout: 10" (dia) •Depth:
5.25" •Speaker system is sold in pairs
Order # MSRP
50-10511 $159.00
Replacement Grill (sold individually)
50-13636 -
ONLY
$90.99
8.57
8" In-Wall Speaker Pair
Full size in–wall speaker is perfect for background or foreground music in whole house distributed audio and as front and rear speakers home theater environments.
Their low cost also makes them suitable in large scale commercial music and paging environments. Features:
•8" poly cone woofer with rubber surround •1" pivoting silk dome tweeter •Cloth backed micro-perforated aluminum grill Specifications: •Power capacity:
55W/80W RMS/peak •Frequency response:
60Hz~20KHz (±3dB) •Sensitivity: 89dB (W/M)
•Impedance: 8ohm Mounting: •Overall frame:
14.25" (H) x 10.25" (W) •Required cutout: 12.25" (H) x
8.75" (W) •Depth: 3.5" •Speaker system is sold in pairs
Order # MSRP
50-10501 $159.00
Replacement Grill (sold individually)
50-13631 -
ONLY
$90.99
8.07
6 www.
MCM electronics.com /
1-800-543-4330
Follow us on: &
AUDIO/VIDEO
Whole House Audio
Section
01
8" Premium Ceiling Speaker Pair
Full size ceiling speaker size is perfect for background or foreground music in whole house distributed audio and as front or rear speakers in home theater environments. High excursion woofers with extremely rigid aluminum cones combine to provide very good low frequency extension. The large vented magnet provides increased power capacity. The mounting frame features a 30° offset, allowing proper aim when mounted close to walls and corners. Features:
•8" aluminum cone woofer with rubber surround •1" aluminum dome tweeter •Cloth backed microperforated aluminum grill •12dB/octave crossover •Selectable bass and treble compensation +3/0/–3dB Specifications:
•Power capacity: 70W/100W RMS/peak •Frequency response: 45Hz~22KHz (±3dB) •Sensitivity: 89dB
(W/M) •Impedance: 8ohm •Magnet size: 30 oz.
Mounting: •Overall frame: 11 1 ⁄
2
" (dia) •Required cutout: 10" (dia) •Depth: 5 1 ⁄
4
" •Sold in pairs
Order # MSRP
50-10561 $199.00
Replacement Grill (sold individually)
50-13636 -
ONLY
$137.00
8.57
Dual 6
1
⁄
2
"
Premium In-Wall Center Channel Speaker
Intended for use in home theater installations as a horizontal center channel speaker, this dual woofer system is also perfectly suitable in vertical arrangement as a front or rear speaker in the home theater, as well as whole house distributed audio. Large dual 6 1 ⁄
2
" aluminum cone woofers provide tremendous mid bass and low frequency response, from a relatively narrow footprint. Shielded woofers solve issues with older CRT monitors, and independent high and low frequency compensation enable tailoring to the individual environment. Features: •Dual 6.5" aluminum cone woofers with rubber surrounds •1" pivoting aluminum dome tweeter •Treble compensation selector +3/0/–3dB
•Bass compensation selector +/0/–3dB •Cloth backed micro-perforated aluminum grill Specifications: •Power capacity: 55W/80W RMS/peak •Frequency response:
60Hz~22KHz (±3dB) •Sensitivity: 90dB (W/M)
•Magnet size: 18 oz. on each woofer •Impedance:
8ohm Mounting: •Overall frame: 8.5" (H) x 18.75" (W)
•Required cutout: 6.5" (H) x 17" (W) •Depth: 3.75"
•Speaker system is sold individually
Order # MSRP
50-10570 $135.00
Replacement Grill (Sold Individually)
50-13645 -
ONLY
$79.49
9.79
6
1
⁄
2
" Premium Ceiling Speaker Pair
Highly popular ceiling speaker size is perfect for background or foreground music in whole house distributed audio and as front or rear speakers in home theater environments. High excursion woofers with extremely rigid aluminum cones combine to provide very good low frequency extension. The mounting frame features a 30° offset, allowing proper aim when mounted close to walls and corners. Features: •6 1 ⁄
2
" aluminum cone woofer with rubber surround •1" aluminum dome tweeter •Cloth backed microperforated aluminum grill •12dB/octave crossover •Selectable bass and treble compensation +3/0/–3dB Specifications:
•Power capacity: 55W/80W RMS/peak •Frequency response: 50Hz~22KHz (±3dB) •Sensitivity: 90dB
(W/M) •Impedance: 8ohm •Magnet size: 17 oz.
Mounting: •Overall frame: 9 3 ⁄
8
" (dia) •Required cutout: 7 5 ⁄
8
" (dia) •Depth: 5" •Sold in pairs
Order # MSRP ONLY
50-10560 $119.00
Replacement Grill (sold individually)
50-13635 -
$115.00
7.06
8" Premium
In-Wall
Speaker Pair
Full size in–wall speaker is perfect for background or foreground music in whole house distributed audio and as front or rear speakers in home theater environments. High excursion woofer with extremely rigid aluminum cone combines to provide very good low frequency extension.
The oversized magnet assembly is vented to provide increased power capacity. This speaker will exceed the performance of bookshelf speakers of over twice the cost. Features: •8" aluminum cone woofer with rubber surround •1" aluminum dome tweeter •Cloth backed microperforated aluminum grill •12dB/octave crossover
•Selectable bass and treble compensation +3/0/–3dB
Specifications: •Power capacity: 70W/100W RMS/peak
•Frequency response: 45Hz~22KHz (±3dB) •Sensitivity:
89dB (W/M) •Magnet size: 30 oz. •Impedance: 8ohm
Mounting: •Overall frame: 14 1 ⁄
4
" (H) x 10 1 ⁄
4
" (W)
•Required cutout: 12 1 ⁄
4
" (H) x 8 3 ⁄
4
" (W) •Depth: 3 1 ⁄
2
"
•Sold in pairs
Order # MSRP
50-10551 $199.00
Replacement Grill (sold individually)
50-13631 -
ONLY
$137.00
8.07
Micro In-Wall Speaker System
✔ Mounts in a single gang box
✔ Includes high pass capacitor
A rugged 2" full range driver is mounted in an attractive rectangular faceplate that is the same size as a standard wall switch or AC outlet. When used alone, it is perfect for voice reproduction in public areas, on kiosks or retail displays.
Used in pairs, and combined with a subwoofer, it is perfect for any high fidelity audio application including home theater and whole-house audio. Specifications:
•Power capacity: 10W/20W RMS/peak •Frequency response: 300Hz~20KHz
•Sensitivity: 85dB (W/M) •Nominal impedance: 8ohm •Front panel dimensions:
4
5
⁄
8
" (H) x 3" (W) •Mounting depth: 1
3
⁄
Order #
4
" •Sold individually
MSRP
50-7907 $39.95
Enclosed Two–Way In–Wall Speaker Pairs
Easy to install in–wall speakers are ideal for background music, paging, home theater or any general music application. Their wide frequency response and above average power capacity make them ideal as main, surround or background speakers. System consists of a woven fiberglass, blue cone woofer, with rubber surround, and a 1" titanium swivel dome tweeter. The addition of a molded
PVC back–box ensures uniform sound quality regardless of mounting location, while protecting the speaker from insulation debris and temperature extremes.
Rotating mounting clips allow fast installation in to drywall with no additional hardware. All will mount in a standard 2 x 4 studded wall. Each speaker is
8ohm. Sold in pairs.
Order #
Woofer
Size
Power Capacity Frequency
RMS/Peak Response
SPL
(W/M)
Overall Frame
Dimensions
50-6547
50-6548
50-6549
5 1
6 1 ⁄
⁄
4
8"
2
"
"
40W/80W
60W/100W
80W/120W
55Hz~20KHz
50Hz~20KHz
50Hz~20KHz
88dB
88dB
88dB
11.75" (H) x 8.3" (W) x 3.6" (D)
12.0" (H) x 8.6" (W) x 4.25" (D)
14.0" (H) x 10.0" (W) x 4.1" (D) www.
MCM electronics.com /
1-800-543-4330
ONLY
$30.99
ONLY
$101.00
128.00
153.00
7
Section
01
AUDIO/VIDEO
Whole House Audio
NEW!
NEW!
NEW!
Complete Four
Zone A-BUS System
Complete package provides virtually everything needed to install a single source, four zone distributed audio system, and is designed for installation in any of
Channel Visions structured wiring panels. Entire system may be controlled from each zone, via include single gang decora keypads, and multiple systems may be interfaced together, allowing additional zones. Keypads connect to the system hub via unterminated Cat 5 cable, and remote speakers connect to keypads via standard in-wall speaker wire (both available separately) Kit
includes: •AB-404 hub •AB-202 line level interface which allows connection of a single source and four
IR emitters •Four AB-124 amplified keypads •Power supply •Four IR emitters •Programmable IR remote control •Mfr. #AB-902
Order #
50-13150
ONLY
$706.00
NEW!
A-BUS Local Source Input
Designed for use in any A-BUS distributed environment, this module provides line level input connection. This unit may be connected to the input of any
A-BUS hub, to act as a standard source input. It may also be located in an individual zone, and connected between the output of the hub and a keypad, allowing connection of a local input source.
This is perfect when a system contains a zone that occasionally has need to listen to an independent source. Device mounts in a single gang opening and is compatible with decora cover plates. Mfr. #AB-301.
Order #
50-13120
ONLY
$92.99
NEW!
Complete Four Source
Four Zone A-BUS System
Complete package provides virtually everything needed to install a four source, four zone distributed audio system. A single gang decora keypad in each zone provides independent source selection, IR remote control and volume adjustment within that zone.
Keypads connect to the system hub via standard
Cat5 cable, and remote speakers connect to keypads via standard in-wall speaker wire (both available separately)
Kit includes: •P-1044 hub, which allows connection of four line level sources, and acts as the system distribution point and power source •Four AB-124 amplified keypads •Power supply •Four IR emitters
•Programmable IR remote control system
•Mfr. #AB-904
Order #
50-13170
ONLY
$989.00
NEW!
Designed for use in any A-BUS distributed environment, this wall mount iPod ® dock serves as one line level audio input source. Compatible with most iPod ® models, including
3rd and 4th generation, this dock provides charge function and supports IR control. Standard single gang device is compatible with decora devices and includes white cover plate, and connects to, and is powered by the A-BUS system via terminated or unterminated Cat 5 cable. Mfr. #AB-313.
Order #
50-13130
iBus
®
iPod
®
Dock
ONLY
$137.00
Crescendo™ Four Source,
Four Zone Cat 5 Audio Distribution Hub
Four source, four zone interface acts as the central hub for a Cat5 audio distributed system. Entire system may be controlled from each zone, via separately available keypads, and multiple systems may be interfaced together, allowing additional zones. Interface also provides connections for up to four IR emitters, allowing it to act as an IR control hub. •Includes
24VDC system power supply •Mfr. #P-2044
Order #
50-13050
ONLY
$262.00
Crescendo™
Single Source,
Four Zone
Cat 5 Audio
Distribution Hub
Single source, four zone interface acts as the central hub for a CAT5 audio distribution system audio system.
Entire system may be controlled from each zone, via separately available keypads, and multiple systems may be interfaced together, allowing additional zones. Interface also provides connections for up to four IR emitters, allowing it to act as an IR control hub. •Includes
24VDC system power supply •Mfr. #P-2014
Order #
50-13040
ONLY
$161.00
NEW!
Order #
50-13100
A-BUS System
Amplfied Keypad
NEW!
Designed for use in any A-BUS distributed environment, this keypad can be used to expand an existing system or as a component in a custom package. Standard single gang device is compatible with decora devices and includes white cover plate.
Mfr. #AB-124.
ONLY
$141.00
A-BUS Source Input Module
Designed for use in any A-BUS distributed environment, this module provides line level input connection, and acts as the IR hub, providing four emitter outputs. A-BUS system output is provided via female RJ45 jack, and IR status is available via 12VDC input connection. This device may be used to expand an existing system or as a component in a custom package.
Mfr. #AB-202.
Order #
50-13110
ONLY
$107.00
8
A-BUS Distribution Module
Designed for installation in Channel Vision structured wiring panels, this module accepts source input from any A-BUS interface device and provides outputs for up to four keypad zones. Multiple modules may be cascaded for additional zones. Requires 24VDC power supply, all connections accept unterminated Cat 5 cable.
Mfr. #AB-404.
Order #
50-13140
ONLY
$70.99
www.
MCM electronics.com /
1-800-543-4330
Follow us on: &
Mini Series
®
Enclosed Ceiling Speakers
The round flush design can be mounted in-ceiling or in-wall to stealthily produce crystal clear sound. The ABS Acou-Seal back box is sealed for improved acoustical response and is especially useful in combating or stopping the transfer of sound through the wall into an adjacent area.
These very small yet durable custom designs use moisture-resistant materials suitable for use in bathrooms, kitchens, saunas, and under outdoor eaves Features: •Ultra small Point Source design •Fast installation for small spaces and background fill
•Back cans for R-rating codes •Shielded magnets •Shallow ABS enclosure for limited depth applications •Sold individually
Order #
50-13270
50-13275
Mfr. #
SML-2
SML-3
Power
Size
2"
3"
Required
Handling (RMS)
20W
30W
NEW!
Frequency
Cutout
4"
4 1 ⁄
2
"
Mura Series
®
In-Wall Speakers
Enclosed metal baffle speakers feature a swiveling titanium dome tweeter, and pearl white, poly-woofers with rubber surrounds. Dual-level controls permit boundary compensation and sound shaping. They are paintable to match your décor, which makes them practically disappear. Speakers are suitable for left, right, front, rear or even center-channel applications.
Features: •Home theater performance in in-wall designs
•Integrated IR mounting hoole for Knoll IR-230 “Peep”
IR receiver (#50-13395) •Designed for horizontal or vertical installation •Front located switches for mid- and high-frequency adjustments •Shielded magnetics •Removable sealed highdensity metal enclosure minimizes sound transfer through walls and floors into adjacent areas R-rating codes
Order #
50-13300
50-13305
50-13310
Mfr. #
SDM-5
SDM-6
SDM-8
Size
5¼"
6½"
8"
Power
Handling (RMS)
80W
100W
120W
Frequency
Response
55Hz~22KHz
45Hz~23KHz
40Hz~23KHz
NEW!
Response
70Hz~21KHz
65Hz~22KHz
Required
Cutout
14 1
14
⁄
8
1
" x 7¼"
⁄
8
" x 8"
20¼" x 10 3 ⁄
8
"
NEW!
Zante Series
®
Ceiling Speakers
Deliver high-definition sound to any room in your home without taking valuable space. Removable back box minimizes sound transmission to adjacent rooms.
Features: •Easy “Dog Leg” installation •Removable back boxes for R-rating codes •Shielded magnets •Pivoting neo-titanium tweeter improves off-axis imaging and high frequencies •Moisture resistant titanium poly cone design suitable for use in kitchens, bathrooms, saunas, and under outdoor eaves
Order #
50-13325
50-13330
Mfr. #
SRZ-5
SRZ-6
Size
5"
6"
Power
Handling (RMS)
80W
100W
Frequency
Response
60Hz~21KHz
50Hz~22KHz
Required
Cutout
7¼" diameter
8¾" diameter
AUDIO/VIDEO
Whole House Audio
ONLY
$70.99
80.99
NEW!
Section
01
Alta
®
Series
Ceiling Speaker
Enclosed speakers feature a pivoting titanium dome tweeter, and pearl white,
WPC poly-woofers. Widedispersion design means you’ll enjoy even coverage across small and large rooms. Alta series speakers are constructed with moisture-resistant materials suitable for use in bathrooms, kitchens, and saunas. Speakers are also suitable for left, right, front, rear or even center-channel applications in any home theater. Features: •Front located switches for mid and high frequency adjustments •Shielded magnets •Removable metal enclosure minimizes sound transfer through walls and floors •Pivoting tweeter improves off-axis imaging and high frequencies •Sold individually
Required Frequency
Order # Mfr. # Size Cutout Response ONLY
50-13285 SRA-6 6½" 10¼" 45Hz~23KHz $132.00
50-13290 SRA-8 8" 123⁄8" 40Hz~23KHz 152.00
NEW!
ONLY
$152.00
162.00
233.00
ONLY
$69.99
80.99
Alta
®
Series Single
Point Stereo
Ceiling Speaker
The Alta single point stereo in-ceiling speaker model SRA-26 reproduces both channels of sound from a single speaker location, which permits great sound even when the décor or layout allows only one speaker. Features: •Moisture resistant design allows installation in bathrooms, kitchens, saunas, and under outdoor eaves •Removable backbox
•Dual push terminal inputs provide stereo sound through two tweeters •Power handling: 110W RMS
•Frequency response: 45Hz~23KHz •Required cutout:
10¼" diameter
Order #
50-13295
ONLY
$182.00
Six Pair Speaker
Distribution Strip
•Allows for connection of up to six speaker pairs to a single amplifier •Removable screw terminal strips accept up to 14AWG wire •Attached mounting plate allows this to be easily mounted to a wall, or installed in most structured wiring panels •Dimensions: 6½" (L) x 2" (W) x 1¼" (H) Note: •Unit provides no impedance protection, and is intended for use with 70V distributed speakers, or 8ohm systems that utilize impedance matching volume controls •Mfr. #WT6
Order #
50-13440
ONLY
$59.99
Zante Series
®
In-Wall 6½" Speaker
Deliver high-definition sound to any room in your home without taking valuable space. Removable back box minimizes sound transmission to adjacent rooms. Features: •Easy “Dog Leg” installation
•Removable back boxes for R-rating codes
•Shielded magnets •Pivoting neo-titanium tweeter improves off-axis imaging and high frequencies
•Moisture resistant titanium poly cone design suitable for use in kitchens, bathrooms, saunas, and under outdoor eaves •Power handling: 100W (RMS)
•Frequency response: 50Hz~21KHz •Required cutout: 9" (L) x 11" (W) •Mfr. #SSZ-6
Order #
50-13320
ONLY
$90.99
NEW!
www.
MCM electronics.com /
1-800-543-4330 9
Section
01
AUDIO/VIDEO
Whole House Audio
Back
Aria
®
Six Zone Whole
House Audio Amplifier
NEW!
This powerhouse is perfect for use as a stand alone amplifier to power six stereo zones in any whole house environment, or it may be used to expand an existing
Channel Vision Aria system. 12 channel amplifier delivers 60W RMS per channel, continuous duty, even with full load on all channels. Features: •Auto turn-on for each channel pair •Each channel pair may select individual source or global input •Quiet fanless convection cooling •Mfr. #A1260
Order #
50-13020
ONLY
$884.00
Multi Zone Audio
Distribution Amplifiers
Back
NEW!
Available in either four zone (8 channel) or six zone (12 channel) configurations, the these amplifiers are designed to meet the needs of custom installed multi-zone systems where high quality sound is a specific requirement. Features: •Protection circuitry protects against low impedance, overheating, overloading, overvoltage and undervoltage •Individual channel gain adjustment •One RCA input per zone •Power can be controlled by external controllers •Channel link: Allows the installer to link any or all of stereo channels to channel one (left and right) without using Y cords or external adapters •Quiet internal fan •Power capacity:
50W/100W (RMS/peak) per channel at 8ohm
Order #
50-13200
50-13205
Mfr. #
MA850
MA1250
Zones
4
6
ONLY
$908.00
1009.00
NEW!
Back
Aria
®
Six Zone A/V Controller/Amplifier
The A4623 is a four input, six zone matrix A/V controller with an integrated audio amplifier, designed for whole house A/V distribution. Any of four inputs can be selected and routed to any of the six stereo zones independently. Separately available keypads allow remote operation of each zone, and are connected to the amplifier via standard Cat5 network cable. In addition to amplifier control, the each keypad acts as a target, providing an IR control path to optional emitters connected to the amplifier. Features: •20W
RMS per channel amplifier in each zone •Pre amp outputs for additional amplification in each zone
•Provides composite video path for each source and output channel •IR and serial control options •Mfr. #A4623
Order #
50-13030
ONLY
$908.00
#50-13000
NEW!
#50-13001
Aria
®
Keypads
Designed specifically for use with the Aria ® model
A4623 six zone amplifier, these keypads are designed to be installed within each zone, and are connected to the central amplifier via standard
Cat 5 cable. Each unit provides source selection, power on/off and volume control for each zone.
Keypads also function as an IR target, with
IR emitter ports being located in the central amplifier.
This allows IR control of source gear from the remote location. Units are single gang size and are compatible with Decora faceplates. Model A0127W is white color,
A0127IA is shipped as ivory, but includes an almond color change kit.
Order #
50-13000
50-13001
Mfr. #
A0127W
A0127IA
ONLY
$36.49
36.49
NEW!
NEW!
Two Channel Stereo Amplifier
4 2ohm stable
4 Auto Power On/Off
High quality discrete audiophile grade amplifier is
2ohm stable, allowing connection of up to four pairs of speakers without impedance concerns, making it ideal for any audio distribution system. Features: •Rear mounted individual gain controls •2 sets of L/R inputs
•Voltage trigger for remote turn on and turn off
•Frequency response: 10Hz~40KHz •Power output
(stereo): 90W RMS x 2 at 8ohm •Power output (mono):
180W RMS x2 at 8ohm •2, 4, and 8ohm stable
•Dimensions (non-rackmount version): 17" (W) x 3.5" (H) x 11.5" (D) •Mfr. #21K
Order #
50-13240
50-13241
Description
Shelf top amplifier
2RU rack mount amplifier
ONLY
$1211.00
1312.00
Illusion 1 Compact
Two Channel
Stereo Amplifier
Ideal for use in a kiosk, for upgrading the sound of a television, in a whole house audio system, or for amplifying speakers for a computer, this amplifier provides terrific sound quality and is extremely compact in design. Features: •Power output: 15W/20W (RMS/ peak) @ 8ohm •Frequency response: 10Hz~40KHz
•2ohm stable •Inputs: one gold plated RCA •Outputs:
Detachable phoenix style •Required power: 15VDC,
2.4A (power supply included) •Dimensions: 4½" (L) x 1¾" (D) x 4" (H)
Order #
50-13220
ONLY
$161.00
NEW!
Order #
50-13230
10
NEW!
Wall Mount
Stereo Amplifier
Ideal for use in a kiosk, for upgrading the sound of a television, in a whole house audio system, or for amplifying speakers for a computer, this amplifier provides terrific sound quality and is extremely compact in design.
Features: •Power output: 15W/24W (RMS/peak) @ 8ohm
•Frequency response: 10Hz~40KHz •2ohm stable •Inputs:
One L/R RCA •Outputs: Detachable phoenix style
•Adjustable bass, treble, and balance •Required power:
15VDC, 2.4A (power supply included) •Dimensions:
6 ½" (L) x 2 ½" (D) x 2 ½" (H) •Mfr. #MA215
ONLY
$181.00
Illusion 2 Compact
Two Channel Stereo Amplifier
4 Bass and treble controls
Ideal for use in a kiosk, for upgrading the sound of a television, in a whole house audio system, or for amplifying speakers for a computer, this amplifier provides terrific sound quality and is extremely compact in design. Features: •Power output: 15W/20W (RMS/ peak) @ 8ohm •Frequency response: 10Hz~40KHz
•2ohm stable •Inputs: One gold plated RCA •Outputs:
Detachable phoenix style •Adjustable bass, treble, and balance •Required power: 15VDC, 2.4A (power supply included) •Dimensions: 4 ½" (L) x 1 ¾" (D) x 4" (H)
Order #
50-13225
ONLY
$191.00
www.
MCM electronics.com /
1-800-543-4330
Follow us on: &
AUDIO/VIDEO
Whole House Audio
Section
01
Compact Stereo Amplifier
This extremely small amplifier chassis is perfect for permanent installations. Typical applications include use with flat panel televisions to drive one or two pairs of speakers, digital signage installations, kiosk, POS and similar retail environments. Features: •20W RMS
8ohm stereo, bridgeable to 40W RMS mono •Fanless cooling for silent operation •Bass and treble controls
•RCA unbalanced line level inputs •Detachable screw terminal speaker outputs •Detachable screw terminal balanced inputs, mic/line switchable Specifications:
•Frequency response: 20Hz~25KHz •Total harmonic distortion (THD): 0.05% •Dimensions: 2 1 ⁄
4
" (H) x 7 3 ⁄
4
"
(W) x 4 1 ⁄
2
" (D) •Mfr. #SLA40
Order #
50-4608
MSRP
$129.99
ONLY
$88.99
Back
Distributed Audio
Stereo Receiver
This receiver is perfect for music listening in any room of the home, with conventional left/right stereo output.
What sets this apart is four amplifier output channels, creating a self contained, four-zone distributed audio receiver. Up to four pairs of bookshelf, in-wall, in-ceiling or outdoor speakers may be driven directly from this unit, with independent selection of any or all pairs. It is perfect in small residential or commercial background music applications. Features: •AM/FM tuner with 30 station presets •Five audio inputs
(including tuner) •Phono input •IR remote control
•Volume, bass and treble controls •Headphone jack
•Power output: 70W RMS x 4 (8ohm), 100W RMS x 4 (4ohm) •THD: <0.2%, 20Hz~20KHz into 8ohm
•Dimensions: 5" (H) x 17
•Mfr. #RX-5502
3
⁄
8
" (W) x 13" (D)
Order #
50-4640
ONLY
$160.00
Stereo Power Amplifiers
•Remote on/off triggering and signal sensing •Front panel controls for level, balance and A/B speaker selection •Two sets of L/R inputs •SLA 150 power output: 7W RMS x 2 channels •SLA 250 power output: 125W RMS x 2 channels
Order #
50-4610
50-4620
Mfr. #
SLA-150
SLA-250
MSRP
$449.00
599.00
ONLY
$227.00
283.00
TM
Compact Stereo Amplifier with Auto On/Off
This extremely small amplifier chassis is perfect for permanent installations. Typical applications include use with flat panel televisions to drive one or two pairs of speakers, digital signage installations, kiosk, POS and similar retail environments. Auto on/off provides convenience, as well as energy savings. Features: •20W
RMS x 2 channels at 8ohm •Automatic on/off with adjustable sensitivity •Off delay: 10~11 minutes •Fanless cooling for silent operation •Bass and treble controls
•RCA unbalanced line level inputs •Push terminal speaker outputs Specifications: •Frequency Response:
20Hz ~ 25KHz •Total Harmonic Distortion (THD):
0.05% •Dimensions: 2 1 ⁄
4
" (H) x 7 3 ⁄
4
" (W) x 4 1 ⁄
2
" (D)
•Mfr. #SLA40AUTO
Order #
50-4609
MSRP
$129.99
ONLY
$80.99
Ultra Compact 40W Stereo Amplifier
Weighing in at less than 6 oz., this miniature stereo amplifier is smaller than a deck of cards, yet delivers an incredible 20W RMS per channel. It is perfect for driving a pair of speakers directly from a portable
MP3 player or PC, flat panel TV or any other line or headphone level source. 92% efficient digital amplifier circuit is housed in a rugged extruded aluminum enclosure and is convection cooled, ensuring whisper quiet operation. Features: •3.5mm input •Included
3.5mm male/male cable •Detachable Phoenix style speaker connections •LED power indicator •Includes
AC adapter Specifications: •Output: 20W x 2CH @
8ohm •THD 0.11% at 50% rated power •S/N ratio:
>99dB •Requires 24VDC, 2A •Dimensions: 1.0" (H)
x 2.2" (W) x 2.78" (D).
Order #
50-4600
ONLY
$82.49
Compact Stereo Amplifier with USB Input
Designed specifically to power a pair of speakers from a standard line level source, such as a CD player, television, and MP3 player. A USB input also allows connection to a desktop or laptop PC to power a set of bookshelf speakers. Features: •20W RMS, 40W peak at
8ohm •Heavy-duty brushed aluminum faceplate •Three position input selector •Stereo 3.5mm line level input
•RCA unbalanced line level subwoofer output •Heavyduty binding post speaker outputs Specifications:
•Frequency response: 20Hz~20KHz •Total harmonic distortion (THD): 0.1% •Dimensions: 3.0" (H) x
10.8" (W) x 7.3" (D) •Mfr. #SLA 100
Order #
50-4606
MSRP
$149.99
ONLY
$112.00
160W Stereo Power Amplifier
4 A/B Speaker Selector
Featuring two auto-switching line level inputs and auto on/off switching, this versatile amplifier is suitable for a number of applications. Features: •A/B speaker selection •Binding post terminals •One stereo line output •Stereo/bridged mode selector •Balance control and volume control •Power output: 80W RMS x 2 channels •Dimensions: 16 ½" (W) x 2 3 ⁄
8
" (H) x 8 ¼" (D)
•Mfr. #PAMP1000
Order #
50-13700
ONLY
$107.00
Six Pair Speaker
Distribution Strip
NEW!
•Allows for connection of up to six speaker pairs to a single amplifier •Removable screw terminal strips accept up to 14AWG wire •Attached mounting plate allows this to be easily mounted to a wall, or installed in most structured wiring panels •Dimensions: 6½" (L) x 2" (W) x 1¼" (H) Note: •Unit provides no impedance protection, and is intended for use with 70V distributed speakers, or 8ohm systems that utilize impedance matching volume controls •Mfr. #WT6
Order #
50-13440
ONLY
$59.99
Single
Channel
Amplifier Module
Compact amplifier is perfect for any general purpose application where a speaker needs to be driven from a line level signal. Its compact size allows it to be mounted most any place, and may be directly attached to the rear of a speaker enclosure. It is ideal for a wide variety of hobby, service and prototype applications. Features: •RCA female input •Accepts line level or headphone level signal •12" attached speaker leads •Barrel type power connector Specifications:
•Input: Line level (80mV) •Output: 12W @ 4ohm
•Requires 6~16VDC, 800mA •Dimensions: 1 x 2
7
⁄
8
" (W) x 2" (D)
5
⁄
8
" (H)
Order #
50-4605
MSRP
$29.95
ONLY
$17.49
www.
MCM electronics.com /
1-800-543-4330 11
Section
01
AUDIO/VIDEO
Whole House Audio
Two Channel Stereo Contractor Amplifier
Highly versatile amplifier is designed to power additional zones in an existing whole house audio system, or multiple zones, with external impedance matching. Because it also includes speaker level inputs, and auto switching, it can also be used to place a local source on a pair of speakers connected to a separate whole-house system. Four trigger modes:
•Audio sensing from a line or speaker level source
•Video sensing at composite video loop-through jack
•12VAC/DC trigger input •Current sensing AC accessory outlet Features: •Speaker and line input
•12VDC trigger output •Recessed front panel gain controls with rear bypass •Heavy-duty binding post speaker outputs •Available in shelf top or 2RU rack mount configurations Specifications: •Power output:
50W RMS (8ohm), 65W RMS (4ohm) per channel
•THD: 0.08% (8ohm load) •Dimensions: 3 1 ⁄
2
" (H) x 17" (W) x 8 1 ⁄
2
" (D)
Order #
50-8845
50-8846
Mfr. #
AMP-BB50S
AMP-BB50S -R
Enclosure
Shelf top
Rack mount
ONLY
$499.00
519.00
#50-8850, 50-8851
#50-8855, 50-8856
Two Channel Stereo Contractor Amplifiers
Highly versatile amplifiers are designed to individual or multiple zones in whole house audio system. High current design makes these amplifiers stable to 2ohm, allowing connection of up to four pairs of speakers without impedance concerns. Units may be manually powered on/off, controlled via external trigger, or set for auto sensing on the line level input. Features: •Line level input with loop-through output •12VDC trigger output
•Front panel gain controls •Heavy-duty binding post speaker outputs •Available in shelf top or rack mount configurations Specifications: •Power output assumes
4ohm load •THD: 0.08% (8ohm load) •Dimensions: see below 3 1 ⁄
2
(H) x 17" (W) x 14 1 ⁄
2
" (D)
Order # Mfr. #
Output Power
RMS x 2CH Enclosure ONLY
50-8850 AMP-BB275S 100W Shelf top $699.00
50-8851 AMP-BB275S-R 100W 2RU rack mount 719.00
50-8855 AMP-BB2125 180W Shelf top 999.00
50-8856 AMP-BB2125-R 180W 3RU rack mount 1019.00
Multi Zone
Multi Channel Contractor Amplifiers
Highly versatile amplifiers are available in four zone (eight channel) and six zone (12 channel) configurations, with either 35W or 65W per channel output, to suite a variety of needs. Additionally, all models are available with tabletop or rack mount chassis, providing a total of eight solutions for a wide range of installation requirements. Features:
•Independent line inputs for each channel pair
•Selectable main bus input with loop through output
•Each amplifier input can be set to left, right or summed mono source •Independent level trim for each amplifier channel •Bridging capability between channel pairs •3~30VAC/DC trigger input •Selectable autosensing or 3~30VAC/DC trigger power ON/OFF
•Heavy-duty binding post speaker outputs
Specifications: •Power output assumes 8ohm load
•See MCMelectronics.com for specific dimensions and distortion specifications
Order # Mfr. # Zones Output Power ONLY
Shelf Top
50-8860 AMP-BB835
50-8865 AMP-BB865
Four 35W RMS x 8CH $1079.00
Four 65W RMS x 8CH 2149.00
50-8870 AMP-BB1235 Six 35W RMS x 12CH 1279.00
50-8875 AMP-BB1265 Six 65W RMS x 12CH 2699.00
Rack Mount
50-8861 AMP-BB835-R Four 35W RMS x 8CH 1099.00
50-8866 AMP-BB865-R Four 65W RMS x 8CH 2169.00
50-8871 AMP-BB1235-R Six 35W RMS x 12CH 1289.00
50-8876 AMP-BB1265-R Six 65W RMS x 12CH 2709.00
Front
Electronic System Cooler
Designed for use with SpeakerCraft multi zone amplifiers, this cooling system can be used with any electronic equipment with heat dissipation issues.
Simply mount above item in the rack, or place directly on top of equipment for highly effective cooling.
Remote trigger accepts 3~24VDC signal from other equipment to turn on fans. Temperature sensing, variable speed fans detect the amount of heat being generated by components, adjusting speed accordingly.
Features : •Completely automatic operation •3.5mm trigger in and out connections •Dual whisper quiet brushless fans •Red LED power indicator •Green LED fan “ON” indicator •Available shelf top or rack mount versions •Two minute shutoff delay Specifications:
•Air volume: 150CFM •Dimensions (shelf): 1
3
⁄
4 x 17" (W) x 10 x 19" (W) x 10
1
1
⁄
⁄
4
4
" (D) •Dimensions (rack): 1
3
⁄
4
" (D)
" (H)
" (H)
Order #
50-8840
50-8841
Enclosure
Shelf top
Rack mount
ONLY
$299.00
349.00
Back
AMP100 Stereo Power Amplifier
Perfect for high fidelity situations needing an independent audio amplifier. Use as part of a multi– amp configuration in home theater systems, a zone amplifier in distributed sound applications, or as a monitor amp in the studio. This solid no–nonsense amplifier provides 50W RMS per channel, at 8ohm, with less than 0.04% THD, and may be bridged for
100W RMS mono. Additional features include A/B speaker outputs, with front panel control, individual
L/R level controls, and heavy-duty five–way binding post outputs. Dimensions: 2.75" (H) x 16.5" (W) x 8" (D).
Order #
50-6062
MSRP
$219.00
ONLY
$147.00
160W Stereo Power Amplifier
4 A/B Speaker Selector
NEW!
Featuring two auto-switching line level inputs and auto on/off switching, this versatile amplifier is suitable for a number of applications. Features: •A/B speaker selection •Binding post terminals •One stereo line output •Stereo/bridged mode selector •Balance control and volume control •Power output: 80W RMS x 2 channels •Dimensions: 16 ½" (W) x 2 3 ⁄
8
" (H) x 8 ¼" (D)
•Mfr. #PAMP1000
Order #
50-13700
ONLY
$107.00
Eight Position Input Selector
Compact table top selector provides cost effective selection of up to eight stereo sources into the line level input of an amplifier. Ideal when multiple sources are present, such as television, computer, portable media players, CD or DVD players, and similar devices, and all need to be switched into a single sound system
Features: •Rugged metal enclosure •Non skid rubber feet •Color coded R/L RCA female input connections
•Individual pushbuttons for each input •Dimensions:
2 1 ⁄
2
" (H) x 12" (W) x 4 1 ⁄
4
" (W)
Order #
50-6202
ONLY
$34.49
12
Automatic A/B
Line Level Switch
This switching device automatically selects between two line level sources to a single input. L/R RCA female input/ output connections accommodate left and right channels, making it perfect for all consumer electronic devices. Default input-A is selected when no signal is present. When a signal is sensed at input-B, the selector automatically switches to that input. A separate
12VDC, 100mA signal is also provided to trigger other external devices. Trigger sensitivity is fully adjustable from 10~100mV. Off delay (from B back to A after absence of signal) is adjustable in eight steps from
0.5 seconds to 10 minutes. This unit requires 12VDC.
Optional AC adapter available (#50-8362).
Order #
50-8385
ONLY
$59.99
www.
MCM electronics.com /
1-800-543-4330
NEW!
Mini Stereo Amplifier with USB Input
Compact amplifier easily drives a moderate pair of speakers and will play MP3 files directly from USB thumb drives or SD cards. •30W x 2CH max output
•Three line level input selector •ID3 tag display
•Repeat play and shuffle functions •Includes: IR remote control •Independent bass and treble controls
•Dimensions: 2.5" (H) x 7.8" (W) x 5.9" (D)
•Mfr. #PVA3U
Order #
50-13825
ONLY
$101.00
Follow us on: &
Multi–Zone Speaker Selectors
Ideal for controlling multiple pairs of installed speaker systems from a single location. Four and eight zone models are available with simple pushbutton on/off control for each zone. Six zone version feature on/off selectors as well as 12 step volume controls for each zone. Features: •Rugged 17" wide metal housing (S4DC is 8
3
⁄
8
") •Front panel impedance protection switch, with rear panel override •Suction feet to hold unit firmly to shelf during use •Removable screw terminal connections accept up to 14AWG wire •100 room labels to customize to any application Specifications: •Power capacity: 125W RMS per channel (all zones combined)
•Frequency response: 20Hz~20KHz ±0dB •Dimensions
(S4DC): 2
3
⁄
(others): 2
3
⁄
16
" (H) x 8
3
⁄
8
" (W) x 6
1
⁄
16
" (H) x 17" (W) x 6
1
⁄
2
2
" (D) •Dimensions
" (D)
Order #
50-8400
50-8430
Mfr. #
S8DC
S6VC
Description
Eight zone
Six zone with volume controls
ONLY
$250.00
425.00
In–Wall A/B Speaker Switch
Simple pushbutton A/B operation allows selection of two speaker pairs from a single amplifier, or a single pair of speakers to select between two separate sources.
Ideal when a pair of in–wall or ceiling speakers is needed for a local stereo or home theater system, and whole house audio. Mounts in standard single gang electrical boxes or low voltage brackets, units include decora cover plate and all hardware.
Order #
50-8440
50-8441
50-8442
Description
White
Bone
Almond
ONLY
$34.99
34.99
34.99
Table-Top Speaker Volume Control
✔ Single speaker pair control
✔ Headphone jack
✔ 100W RMS capacity
Table-top control center provides external volume adjustment for a single pair of speakers. 12 position rotary control utilizes multi tapped transformers for efficient power transfer, with no heat build-up.
Order #
50-6216
ONLY
$39.99
Two-Way
Speaker
Switch Box
Tabletop control box allows selection of A/B speaker pairs. Internal 220ohm resistors ensure that amplifier always sees a load, even with both switches off. With both speaker switches in “on” position, speaker pairs are connected in series, allowing use of 4ohm or 8ohm speaker systems, without damage to amplifier. 200W maximum power capacity. All connections are push type. Metal case has non-skid rubber feet and stays securely in place. Dimensions: 6.9" (W) x 2.2" (H) x
3.9" (D). Sloped front, black color.
Order #
50-6185
ONLY
$21.99
AUDIO/VIDEO
Whole House Audio
Section
01
NEW!
Speaker Selectors
Compact shelf top selectors allow zone control of up to four, six or eight pairs of speakers. Internal impedance protection circuit ensures your amplifier sees a safe load, even when all pairs are playing. Resistor type impedance matching allows full 20Hz~20KHz frequency response. •Pushbutton control for each speaker pair •Push terminals accept up to 14AWG cable •Handles total of 100W per channel
Order #
50-13770
50-13375
50-13380
Mfr. #
PSS4
PSS6
PSS8
Pairs
Four
Six
Eight
ONLY
$38.49
151.00
45.49
Speaker Selectors with Volume Control
Compact shelf top selectors allow zone control of up to four or six pairs of speakers, with individual level control of each pair. “A” and “B” amplifier input allows connection of two separate stereo sources, with independent A/B source selection at each pair. Internal impedance protection circuit ensures your amplifier sees a safe load, even when all pairs are playing. Resistor type impedance matching allows full 20Hz~20KHz frequency response. •Push terminals accept up to
14AWG cable •Handles total of 100W per channel
Order #
50-13760
50-13365
Mfr. #
PSPVC4
PSPVC6
Pairs
Four
Six
ONLY
$147.00
163.00
Speaker Selectors
✔ Volume adjustment in each zone
✔ A/B source selection
✔ 100W RMS capacity
Versatile speaker switches allows connection of up two six pairs of speakers, to two different stereo sources, with individual volume control of each pair.
Volume adjustment and impedance matching is accomplished through internal heavy-duty multitrapped transformers. Rear screw terminal strips accept up to 14AWG wire, and are removable, allowing easy connection of multiple cables. Power capacity:
18W/50W RMS/program per speaker, 100W/150W
RMS/program total. Dimensions: 3" (H) x 17" (W) x 7" (D), including knobs.
Order #
50-6675
50-6676
Speaker Pairs
Four
Six
ONLY
$206.00
247.00
Eight Position Speaker Selector
Compact table top selector provides cost effective selection of up to eight pairs of speakers, from one location. It provides a perfect solution to the need for low cost distributed audio in residential audio or commercial sound applications. Internal switching uses a combination of series and parallel wiring, ensuring that the connected amplifier sees a minimum of a 4ohm load (when 8ohm speakers are used). This means that any conventional amplifier or stereo receiver can drive multiple sets of speakers, without the need for external impedance matching devices. Features: •Rugged metal enclosure •Non skid rubber feet •Color coded push terminals for all speaker connections •Heavy-duty rocker switches •Attractive sloped top panel •Power capacity: 50W RMS per channel •Frequency response: 10Hz~50KHz •Dimensions: 2 1 ⁄
2
" (H) x 12" (W) x 4 1 ⁄
4
" (W)
Order #
50-6225
ONLY
$39.99
Five-Way Speaker Switch Box
✔ On/off control for five zones
✔ Headphone jack
✔ Compact size
Maintains 8ohm load when up to five sets of 8ohm speakersare used. Places 100ohm load when all speakers are switched off. Front panel x 2
1
⁄
4
" (H) x 3
5
⁄
8
1
⁄
4
" headphone jack allows monitoring of the source. 200W maximum power capacity. Metal case has non-skid rubber feet and stays securely in place. Dimensions: 8
1
⁄
8
" (W)
" (D). Sloped front, black color.
Order #
50-6200
ONLY
$28.49
Free Standing Stereo Volume Control
Intended for use when in-wall type controls are not practical, this control is ideal for use with free standing remote speaker systems. Features: •Removable terminal strip for greatly eased installations •12 step attenuation
•Suction cup feet to hold the unit secure during use
Specifications: •Power capacity: 60W RMS •Frequency response: 20Hz~20KHz •Dimensions: Overall depth:
2.19" (H) x 8.5" (W) x 6.5" (D) •Call for larger quantity pricing
Order #
50-8275
ONLY
$92.99
Automatic A/B
Speaker Level Switch
This switching device automatically selects between two stereo amplifiers to a single pair of speakers. It is perfect in situations where installed speakers are used with both a local stereo or home theater system, and a distributed audio system. Default input-A is selected when no signal is present. When a signal is sensed at input-B, the selector automatically switches to that input. A separate 12VDC, 100mA signal is also provided to trigger other external devices. Trigger sensitivity is fully adjustable from 30~300mV. Off delay
(from B back to A after absence of signal) is adjustable in eight steps from 0.5 seconds to 10 minutes. Relay contacts are 4PDT, with isolated L/R ground paths.
Music power capacity is 100W. This unit requires
12VDC. Optional AC adapter available (#50-8362).
Order #
50-8390
ONLY
$90.49
www.
MCM electronics.com /
1-800-543-4330 13
Section
01
AUDIO/VIDEO
Whole House Audio
Elevate™ Whole Home Music System
This complete four zone sound system brings multi– zone, multi–source audio to a new price level. Features:
•Four independent stereo amplifier channels, one for each zone •Individual keypad control for each zone
•Independent selection from two input sources from each zone •Complete control of input source, volume level and system power on/off from each keypad
•Infrared repeating from each keypad to control source devices as well as the Elevate™ unit Elevate™ amplifier
includes: •Elevate base unit •Allport™ connection cable •Two IR emitters •IR remote control •Complete four-room kit also includes four remote keypads
Specifications: •Power output: 15W RMS x 8 CH
•THD: 0.4% •Frequency response: 30Hz~20KHz
•Power requirements: 110/220VAC, 50/60Hz, 166W
•Dimensions: 3.5" (H) x 8.5" (W) x 12.75" (D)
Order #
50-4650
Mfr. #
BA-2430S
ONLY
$494.00
A/B Input Source Switch Box
Compact control box allows selection of two input sources into a single auxiliary or tape input. Single push button switch selects source “A” or
“B”. Ideal when connecting audio devices such as CD players, VCRs, laser disk players and satellite receivers to home stereo equipment. Output connection is made via attached 5' lead, terminated with male RCA type connectors, color coded red and white.
Input connections are RCA type female. Rugged metal enclosure is black in color, dimensions: 3" (W) x 1" (H) x 3" (D) including switch and connections.
Order #
50-6220
ONLY
$10.49
Elevate™ 6.6 Whole Home Music System
This complete six zone, six source sound system brings multi-zone, multi-source audio to a new price level.
Purchase the BA-6640MS as the main unit, to drive up to six zones. Add the BA-6640XS Expander to the main unit, to control up to a total of 12 zones.
Features: •Six independent stereo amplifier channels, one for each zone •Individual keypad control for each zone •Independent selection from up to six input sources from each zone •Complete control of input source, volume level and system power on/off from each keypad •Infrared repeating from each keypad to control source devices as well as the Elevate™ unit.
Complete six zone kit includes: •Elevate 6.6 base unit
•Allport™ connection cable •IR emitters •IR remote control •Six remote keypads Specifications:
•Power output: 20W RMS x 12 CH •THD: 0.4%
•Frequency response: 30Hz~20KHz •Power requirements: 110/220VAC, 50/60Hz, 166W
•Dimensions: 3.5" (H) x 17" (W) x 12.75" (D)
Order # Mfr. # Description ONLY
50-4645 BA-6640MS Complete Six Zone Kit $988.00
50-4647 BA-6640XS Six Zone Expander 988.00
Three-Way Audio/Video Switch Box
Tabletop control box allows selection of multiple A/V sources. Ideal when connecting several devices, such as CCTV cameras, camcorders, VCRs, laser disk players and satellite receivers to a single video monitor or VCR. Accommodates video and left and right audio, all connections are all RCA type female.
Metal case has non-skid rubber feet and stays securely in place. Dimensions: 6.9" (W) x 2.2" (H) x 3.9" (D).
Sloped front, black color.
Order #
50-6195
ONLY
$22.99
Elevate™ Music System
Learning Remote Control
Learning IR remote control operates all functions of the Elevate™ Music
System, and may be programmed to operate source devices. This allows operation of tuners, satellite receivers,
CD or DVD players from any
Elevate™ zone, simply by pointing the remote at the wall mounted keypads.
Order #
50-4651
Mfr. #
BA-LRC1
ONLY
$35.49
Top
Input Source
Switch Boxes
Tabletop control box allows selection of multiple input sources.
Back
Ideal when connecting several audio devices, such as CD players, VCRs, laser disk players and satellite receivers to home stereo equipment. Models available to select from three, four or five sources. Internal PC board design provides quiet, reliable operation. All connections are all RCA type female. Metal case has non-skid rubber feet and stays securely fixed in place.
Dimensions: 6.9" (W) x 2.2" (H) x 3.9" (D).
Order #
50-6170
50-6175
50-6180
Positions
Three
Four
Five
ONLY
$16.49
17.99
19.49
Dual Channel
Ground Loop
Isolator
Ground loop problems in A/V systems normally appear as a hum in speakers or horizontal bars on video monitors. These problems typically occur when multiple components receive AC power from different locations, or because CATV, satellite or antenna systems provide a separate ground point. This isolator solves that problem by providing ground path isolation between components, while maintaining full frequency response. Features: •Rugged steel enclosure
•RCA input and output connections •Fully independent L/R channels Specifications: •Frequency response: 10Hz~50KHz •THD: 0.01% •Dimensions:
1.50" (H) x 3.50" (W) x 2.50" (D) •Passive device, requires no power
Order #
50-9040
MSRP
$49.95
ONLY
$36.49
14
Input Source Mixer/Headphone Amplifier
Versatile table-top device features two stereo line level inputs and a single line level output, allowing the user to mix two sources into one. Slide controls allow independent gain adjustment for each source. Front panel 3.5mm stereo headphone jack, with slide level control, is provided for monitoring of the mixed source. Compact unit is perfect for any application requiring a low cost line mixer, or headphone amplifier.
Metal case has non-skid rubber feet and stays securely in place. All connections, except headphone, are RCA type female. Requires 12VDC, 100mA. AC adapter included. Dimensions: 1
3
⁄
4
" (H) x 5" (W) x 4
1
⁄
2
" (D).
Black color.
Order #
50-6182
ONLY
$30.99
24 Bit/96K D/A Convertor
This compact unit will accept standard coax or Toslink
SPDIF signal, and convert it to line level audio. It is perfect when there is a need to send digital audio signal to an amplifier not having digital inputs, including home audio receivers, prosound amplifiers and mixing consoles. It is perfect when an unused digital output on a piece of home theater equipment needs to be sent to a separate whole house audio amplifier. Features: •Two
Toslink inputs •Two coax inputs •Four-position input selector with LED indication •
1
⁄
4
" headphone output with adjustable level •Separate REC and AMP line level L/R RCA outputs (both fixed level) •LED power indicator Specifications: •Digital input: 96KHz
(standard SPDIF) •Resolution capability: 24 bit
•Amplitude linearity: 1.06dB •Frequency response:
20Hz~20KHz •Channel separation: 100dB @ 1KHz
•S/N ratio: 103dB •THD: <0.0015% •Digital filter:
82dB •Headphone output: 700mW, 8~32ohm
•Power requirements: 12VDC, AC adapter included
•Dimensions: 1
1
⁄
2
" (H) x 9
3
⁄
4
" (W) x 4
1
⁄
2
" (D)
Order #
50-7774
MSRP
$179.00
ONLY
$121.00
www.
MCM electronics.com /
1-800-543-4330
Follow us on: &
Simple IR Hub
NEW!
Compact “Y” cable
“hub” allows simple connection of one IR emitter to one IR target.
Includes AC adapter: the only additional items required are the actual target and emitter. Connections are
3.5mm female. Mfr. #IR-1200.
Order #
50-13004
ONLY
$12.99
AUDIO/VIDEO
Whole House Audio
Section
01
NEW!
Universal IR Target
Ultra sleek and compact IR target features remote mounted electronics, allowing much greater flexibility when hiding among equipment. It is fully compatible with any Channel Vision IR distribution system and terminal strip connection allows use with conventional twisted pair cable. Mfr. #IR-2400
Order #
50-13015
ONLY
$68.99
NEW!
Keystone Mount
DC Power
Connection
This keystone insert features a standard barrel jack which accepts connection from most AC adapters. It is essential when low voltage must be inserted into a Cat 5 pair for remote distribution. It is ideal for remote powering of small
LCD monitors, video cameras, IR repeater systems and similar items. Rear mounted IDC connector allows simple, fast connection to unterminated 22~24AWG solid or stranded wire. Maximum voltage: 24VAC/DC,
1A. Barrel size: 2.1mm I.D., 5.5mm O.D.
•Sold individually
Order #
50-7752
MSRP
$11.95
ONLY
$8.07
NEW!
Expandable Amplified IR Hub
Compact hub acts as the central connection point for multiple IR emitters and targets in a distributed system.
IR target input accepts either a 3.5mm plug, or screw terminal connections for use with twisted pair cable.
Four 3.5mm IR outputs allow connection of multiple emitters. Two LEDs are provided for power and LED status indication. AC adapter is included as well.
Mfr. #IR-1203
Order #
50-13005
ONLY
$30.49
NEW!
Wall Mount IR Target
Decora style target is compatible with any Channel
Vision IR distribution system. Terminal strip connection allows use with conventional twisted pair cable, and decora style plate is compatible with standard wall plates. Attractive single gang snap-on cover plate attaches without hardware, for a sleek low profile look. Mfr. #IR-2005.
Order #
50-13010
ONLY
$70.99
All-In-One
Complete
IR System
NEW!
Complete IR system includes an
IR target, four-output distribution hub and four emitters, everything needed for complete IR remote control. It is perfect for use with wall mounted LCD or plasma displays, or in entertainment centers where components are located inside the cabinet. IR target cord length, 36", IR emitter cord length, 72". Kit includes mounting brackets, adhesive tape and AC adapter. Mfr. #IR-5000
Order #
50-13049
ONLY
$83.99
#50-13025
Universal IR Emitters
NEW!
Compact IR emitters utilize 3.5mm male plugs for compatibility with all Channel Vision IR distribution systems, and most others.
Units include adhesive mounting tape, allowing simple installation on the face of most equipment. Single head unit operates one device and includes 6' of attached cable. Dual head unit operates two devices simultaneously and includes 12' of attached cable.
Order #
50-13019
50-13025
Mfr. #
IR-3001
IR-3002
Type
Single head
Dual head
ONLY
$5.04
8.68
#50-13029
#50-13035
IR Over Coax
System Components
Individual IR engine components are useful when installing a custom IR system in an old-work or retrofit installation. The IR coax engine includes the necessary
AC adapter and features a 3.5mm female connector, for use with any Channel Vision IR emitter, allowing it to receive IR commands via the existing RG59/U or RG6/U coax. The IR target includes the matching coax engine, allowing the IR signal to be inserted into the RG59/U or RG6/U coax. Both items are sold separately.
Order #
50-13029
50-13035
Mfr. #
IR-4000
IR-4101
Description
IR Coax Engine
IR Coax Target
ONLY
$27.99
39.99
NEW!
Bypass Cable
Use with channel Vision coax IR engine products to bypass amplified couplers and other devices that do not pass DC. Must be used with IR-4000 and IR-4100 couplers, sold separately. Mfr. #IR-4180
Order #
50-13039
ONLY
$6.76
NEW!
Complete IR Over Coax System
In old-work and retrofit installations, the simplest method of sending IR remote control operation to another room, is over the coax cable already in use.
This complete IR coax engine system will allow just that. The kit includes an IR coax engine, with power supply, a dual head IR emitter, and plasma proof IR target. Components connect in-line with existing
RG59/U or RG6/U cable, with no effect on cable system performance. Note: Any splitters in the signal path between components must be DC passive.
Mfr. #IR-4500
Order #
50-13045
ONLY
$76.99
Keystone Mount
3.5mm Connector
This keystone insert features a standard
3.5mm threeconductor female jack which may be used in two or three conductor applications. It is ideal any time a 3.5mm connector is needed at a wall plate. Rear mounted IDC connector allows simple, fast connection to unterminated Cat 5 cable, or any 22~24AWG solid or stranded, UTP or shielded wire. Maximum voltage:
24VAC/DC, 1A. Applications: •Remote location of headphone jacks •Remote microphone connections
•Remote input from PC sound card, MP3 player or iPod™ •IR repeater connection •Remote triggering of A/V components •Low voltage DC connection
•Sold individually
Order #
50-7753
MSRP
$12.95
ONLY
$8.37
www.
MCM electronics.com /
1-800-543-4330 15
Section
01
IR Emitter
AUDIO/VIDEO
Whole House Audio
Micro receivers
Table Top
Mini Receiver
Peephole
IR Emitter
Shelf Top IR Receiver
Compact receiver is designed to be used on top of any piece of furniture, and features a standard three wire connection. Features:
•Up to 35' reception distance
•CFL proof and plasma friendly •Maximum cable length: One mile with 18 gauge three conductor cable •Nominal reception angle: 45° off axis •Required power: 12VDC, 35mA
•Dimensions: 2 5 ⁄
8
" (L) x 3" (W) x 1" (H) •Mfr. #IR100
Order #
50-13380
ONLY
$45.49
Power supply Connection block
Four Target IR
Repeater Kits
Ideal for controlling A/V products that may be hidden in a closet, enclosed in a cabinet, or in a different room, these infrared repeater kits include everything you need for a multi-room installation. Includes: •Four infrared receivers: Available with either four wall plates, or four micro receivers, in a variety of colors to match any decor. Micro receivers are smaller than a quarter, and ideal for a simple, yet stealthy installation. Wall plate receivers are standard single gang, decora style. Each receiver is CFL proof, and plasma friendly. •Connection block: Allows for connection of up to four emitters, and ten infrared receivers •Infrared emitters: Each kit includes two dual infrared emitters •Power supply:
12VDC, 200mA power supply will power up to five infrared receivers
Color ONLY Order # Mfr. #
Kits with Wall Plate Receivers
50-13350
50-13351
50-13352
50-13353
IR-JBOX-W
IR-JBOX-A
IR-JBOX-I
IR-JBOX-B
Kits with Micro Receivers
50-13360
50-13361
50-13362
IR-MICRO-4-W
IR-MICRO-4-S
IR-MICRO-4-B
White
Almond
Ivory
Black
White
Silver
Black
$373.00
373.00
373.00
373.00
503.00
503.00
503.00
Single Target
IR Repeater Kits
Ideal for controlling A/V products that may be hidden in a closet, enclosed in a cabinet, or in a different room, these infrared repeater kits include everything you need for a basic installation. Includes: •Infrared receiver: available in various configurations to suit your needs.
Mini receiver is smaller than a quarter, and ideal for a simple, yet stealthy installation. Peephole receiver is ideal for custom installation, such as behind the grill of an in-wall speaker, or in a door, and includes interchangeable gold or white trim rings. Each receiver is CFL proof, and plasma friendly. •Connection block:
Allows for connection of up to four emitters, and 10 infrared receivers •Infrared emitters: Each kit includes two dual infrared emitters •Power supply: 12VDC,
200mA power supply will power up to 5 infrared receivers
Order # Mfr. #
Kits with Mini Receiver
50-13355
50-13356
Color
IR-MICRO-1-W White
IR-MICRO-1-B Black
Silver 50-13357 IR-MICRO-1-S
Kit with Peephole Receiver
50-13365 IR-PEEP Gold or white
Kits with Postage Stamp Receiver (not shown)
50-13370
50-13371
IR-POST-B
IR-POST-G
Black
Gray
Kit with Tabletop Receiver
50-13375 IR-TABLE Black
ONLY
$232.00
232.00
232.00
163.00
181.00
181.00
151.00
Decora Style Infrared
Receiver Wall Plates
Single gang decora style IR receivers provide an attractive, professional IR target. Blue IR activity LED provides feedback when IR signal is received.
Three screw terminal and RJ45 connector make installation a breeze in any standard three wire IR repeater system. Features:
•Up to 35' reception distance •CFL proof and plasma friendly •Maximum cable length: 1 mile with 18 gauge three conductor cable •Nominal reception angle: 45º off axis •Required power: 12VDC, 25mA •Dimensions:
4" (H) x 1 1 ⁄
2
" (W) x 1" (D)
Order #
50-13385
50-13386
50-13387
50-13388
Mfr. #
IR-210-W
IR-210-W
IR-210-W
IR-210-W
Color
White
Almond
Ivory
Black
ONLY
$59.99
59.99
59.99
59.99
A B
C D
Infrared Repeater System Connection Modules
Available in either a standard block style, or a stylish decora style wall plate design, these connection modules are the heart of any IR distribution system. Connection modules connect to up to ten IR receivers, and distribute the signal to up to four single or dual
IR emitters. •Decora cover not included
ONLY Order # Mfr. # Color
Wall plate style (single gang decora)
50-13405
50-13406
50-13407
50-13408
Block style
50-13410
IR54-W
IR54-A
IR54-I
IR54-B
IR55
White
Almond
Ivory
Black
Black
$35.49
35.49
35.49
35.49
35.49
Peephole Style Infrared Receiver
Ideal for any installation when a flush mounted IR receiver is necessary, this peephole style IR receiver comes with two interchangeable trim rings, gold and white. One possible application for this receiver is installation behind the grill of an in-wall speaker.
Features: •Up to 50' reception distance •CFL proof and plasma friendly •Maximum cable length: 1 mile with 18 gauge three conductor cable •Nominal reception angle:
45º off axis •Required power: 12VDC, 25mA
•Mounting diameter: ½" •Mounting depth: 1 1 ⁄
3
"
•Mfr. #IR230
Order #
50-13395
ONLY
$91.99
Infrared Emitters
Available with or without a status LED, and in a single or dual emitter configuration, these infrared emitters from Knoll simply attach to any standard terminator block with the attached 3.5mm plug (10' cord). Available individually, or in a money saving ten pack.
16
Order # Status LED
Single Emitter (sold individually)
50-13415
50-13425
50-13420
50-13430
No
Yes
Dual Emitter (sold individually)
50-13416
No
Yes
Single Emitter (10 per package)
50-13426
No
Yes
Dual Emitter (10 per package)
50-13421
50-13431
No
Yes www.
MCM electronics.com /
1-800-543-4330
ONLY
$14.49
14.49
16.49
19.49
99.99
111.00
121.00
151.00
E
Miniature IR Receivers
Extremely compact receivers can be used virtually anywhere. Features: •IR activity
LED provides feedback when IR signal is received
•Up to 30' reception distance •CFL proof and plasma friendly •Maximum cable length: One mile with 18 gauge three conductor cable •Nominal reception angle:
45 degrees off axis •Required power: 12VDC, 25mA
Color ONLY Fig. Order # Mfr. #
Micro receivers
A
B
C
50-13390
50-13391
50-13392
Postage stamp receivers
D 50-13400
E 50-13401
IR220-W
IR220-S
IR220-B
IR250-B
IR250-G
White
Silver
Black
Black
Gray
$99.99
99.99
99.99
99.99
99.99
Order #
50-13435
12VDC Power Supply
Plugs directly into any Knoll systems infrared connection module, and powers up to five
Knoll Systems IR receivers and up to four IR emitters.
•Current: 200mA
•Mfr. #PS1202
ONLY
$15.49
Follow us on: &
SmartPath Infrared Repeating System
SmartPath’s easy installation and configuration allow installers to quickly create a pathway of complete A/V system control. All components are available separately for versatile configuration of any custom system. Emitters and receivers may be connected with two pairs of 24AWG solid or stranded unshielded twisted pair wire, including standard Cat 5, for distances up to 1200'. Heavier gauge cable can be used for distances of up to 5000'. A complete system requires the following four basic components: •At least one infrared receiver •One connecting block •As many emitters as needed to control A/V components •One DC power supply
AUDIO/VIDEO
Whole House Audio
Section
01
Standard IR Emitters
Compact sensors attach via included double sided adhesive, and may be mounted near equipment to be controlled. Multiple configurations are available to suit a variety of applications. Dual emitter units allow placement in front of two pieces of equipment, from only one plug connection. Units with visible LEDs provide visible feedback of presence of IR signal.
Each includes an attached 8' lead, terminated with a two-conductor 3.5mm plug.
Order #
50-8356
50-8357
50-8358
50-8359
Mfr. #
IRE-1.0
IRE-2.0
IRE-3.0
IRE-4.0
Description
Single emitter
Dual emitter
Single emitter w/visible LED
Dual emitter w/visible LED
ONLY
$11.99
21.99
11.99
19.99
Wall Mount “Junction
Box” IR Receivers
Attractive receivers include clearly visible system status and IR activity LEDs, to provide positive feedback to the user, and mount in standard single gang junction boxes or low-voltage brackets.
Order #
50-8330
50-8332
Mfr. #
IRC-4.0
IRC-4.0
Color
White
Almond
ONLY
$120.00
120.00
High Power IR Blaster
Designed for installation into equipment rack, this unit is intended to provide sufficient output to control all components.
The unique 3" wand features two high output
IR emitters “flooding” the rack with the remote signal.
The wand can be adjusted above or below a rack of components to suit specific situation. Attached 8' lead is terminated with a two-conductor 3.5mm plug.
Order #
50-8360
Mfr. #
IRE-5.0
ONLY
$29.99
Surface Mount
Mini IR Receivers
Compact receivers are intended for surface mounting on cabinets, TV sets or the wall, with attached double sided adhesive. Clearly visible system status and IR activity LEDs provide positive feedback to the user. Black version, with stripped leads is also available with the ALR (ambient light restrictor) lens for use near plasma displays. Standard receivers provide a reception angle of 110°, the ALR version is 60°. Dimensions: 2
9
⁄
16
" (L) x
17
⁄
32
" (W) x
9
⁄
16
" (L)
Order # Mfr. # Color
50-8316 IRC-2.0
50-8317 IRC-2.1
Black
White
50-8318 IRC-2.1 Black
50-8319 IRC-2.1 ALR Black
Connection ONLY
3.5mm plug $121.00
Bare leads
Bare leads
Bare leads
121.00
127.60
127.65
SmartPath
Connecting Cables
Use to adapt components for use with other equipment, or to extend existing leads. Sets include:
•PTP-8: Set of six,
8' 2-conductor cables, male to male 3.5mm plugs •PTJ-40: 40' 2-conductor cable, male to female 3.5mm plugs •QIX-1.0: 15'
4-conductor cable, male to female 3.5mm plugs
•SAC-1.0: Diode protected “Y” cable, single female to two male 3.5mm plugs, allows connection of one emitter to two sources •PTS-3: Set of six, 36"
2-conductor cables, male 3.5mm plug to stripped leads •STS-4: Set of six, 48" 2-conductor cables, barrel type power plug to stripped leads.
Order #
50-8373
50-8375
50-8377
Mfr. #
PTP-8
QIX-1.0
PTS-3
ONLY
$32.99
8.50
12.49
Complete SmartPath
IR Repeater System
Take the guess work out of setting up a typical one room system with this complete
IR repeater kit, everything is included in one convenient package. System includes:
•One IRC-3.0 shelf top receiver •One AT-1.0 amplified terminator unit
•One PS-1.0 power supply
•Four IRE-1.0 IR emitters
Order #
50-8363
Mfr. #
IRC-3.0 KIT
ONLY
$215.00
Flush Mount
Mini IR Receivers
Compact receivers require only a
1
⁄
2
" hole, and may be mounted flush in cabinets or walls, leaving only a circular bezel exposed to the room.
They may also be mounted behind the grill of most in-wall speakers. Each includes a set of four color bezels (almond, black, bone and white), to match any décor. Also included are two specially designed ALR
(ambient light restrictor) bezels, for use near plasma displays. Clearly visible system status and IR activity
LEDs provide positive feedback to the user. Receivers provide a reception angle of 110° standard, 60° with
ALR bezel installed. Dimensions: •Unit:
2
5
⁄
8
47
⁄
64
" (L) •Cap bezel:
47
⁄
64
" diameter x
23
⁄
64
" diameter x
1
⁄
8
" (L)
15
⁄
32
" diameter x
" (L) •ALR bezel:
Order #
50-8310
Mfr. #
IRC-1.0
Connection
3.5mm plug
ONLY
$126.10
Passive Terminator
The PT-1.0 passive terminator functions as central control unit for compact, single room
IR systems, allowing connection of the power supply, up to two IR emitters and a single IR receiver, equipped with a four-conductor 3.5mm plug.
5~24VDC status input accepts status signal from IR controlled equipment, and provides visual indication at the IR receiver.
Order #
50-8340
Mfr. #
PT-1.0
ONLY
$11.49
Ultra Compact Plasma
Block Mini IR Receivers
These units are designed to block plasma, CFL, EMI, and ESI noise sources, using SpeakerCraft’s exclusive “smart” circuit (patent pending). The actual sensor and electronics are separated into separate “main” and
“pick-up” modules, enabling installation into very tiny spaces of furniture recesses, monitor panels and under shelves. Overall reception angle is 100°. Dimensions:
•Pick-up module: module: 2 9
7
⁄
16
" (L) x
⁄
8
" (L) x
9
13 ⁄
32
" (W) x
⁄
16
" (W) x 1 ⁄
2
" (D)
9 ⁄
32
" (D) •Main
Order #
50-8320
50-8321
Mfr. #
IRC-2P2.0
IRC-2P2.1
Connection
3.5mm plug
Bare leads
ONLY
$115.00
115.00
#50-8361
SmartPath IR System
Power Supplies
Supplies plug directly into SpeakerCraft terminator models
AT-1.0 or PT-1.0 to provide power to the entire IR repeater system. Current draw of
SpeakerCraft devices are as follows:
•IR emitters: 15mA •IR receivers:
6mA •IR blasters: 150mA •Terminator units AT-1.0 and PT-1.0 add no additional current draw
Order #
50-8361
50-8362
Mfr. #
PS-2.0
PS-1.0
Current
1200mA
200mA
#50-8362
ONLY
$55.49
13.49
Shelf Top
IR Receivers
Compact receivers are housed in an attractive case to sit on the surface of a cabinet or shelf. Clearly visible system status and IR activity LEDs provide positive feedback to the user. Models include an 8' attached lead, terminated with SpeakerCraft’s unique fourconductor 3.5mm plug. Provides a reception angle of
110°. Dimensions: 1 1
⁄
8
" (L) x 3
3
⁄
16
" (W) x 1
1
⁄
16
" (D)
Order #
50-8325
Mfr. #
IRC-3.0
ONLY
$75.49
www.
MCM electronics.com /
1-800-543-4330 17
Section
01
NEW!
AUDIO/VIDEO
Whole House Audio
50-13500
Coliseum Series 5"
Indoor/Outdoor Speakers
4 Available with or without 70V transformer
50-13501
The Coliseum C120 is a high-end, water resistant speaker featuring specially treated drivers and a sculpted ABS plastic enclosure. This compact speaker is ideally suited for many applications: commercial installations, home theatre, home stereo, mobile applications, reference monitor, personal stage monitor, etc. Features: •Pivoting tweeter •Power handling: 100W
RMS •Frequency response: 75Hz~19KHz •Microphone stand mountable •U-bracket included •Paintable enclosure •Inputs: Push terminals and ¼" •Dimensions
(H x W x D): 10¼" x 6½" x 6¾" •#50-13507 allows for more versatile mounting options •#50-13508 protects
¼" jacks from the elements when not in use
•Sold Individually
Order # Mfr. # Description Color ONLY
Indoor/Outdoor Speakers
50-13500 C120
50-13501 C120W
-
-
Black $80.49
White 80.49
Indoor/Outdoor Speakers with 70V Transformer
50-13505 C120/70 -
50-13506 C120W/70 -
Black 96.49
White 96.49
Accessories
50-13507 C120MOUNT Ceiling/Wall bracket Black 22.99
50-13508 MSC0016 ¼" jack cover Black 0.49
NEW!
Coliseum Series Amplified
5" Indoor/Outdoor Speaker
The Coliseum C120P is a high-end installation speaker, featuring specially treated drivers and a sculpted ABS plastic enclosure. This compact powered speaker is ideally suited for many applications: commercial installations, home theatre, home stereo, mobile applications, reference monitor, personal stage monitor and can be used outdoors. Features:
•80W RMS power output •Volume, bass and treble controls •Inputs: ¼" and 3.5mm •3.5mm output for pairing two together, providing true stereo operation
•U-bracket included •Frequency response:
75Hz~19KHz •Dimensions (H x W x D): 10 ¼" x 6 ½" x 6 ¾" •#50-13507 allows for more versatile mounting options •#50-13508 protects ¼" jacks from the elements when not in use •Sold Individually
Order # Mfr. # Description Color ONLY
Indoor/outdoor speaker
50-13510 C120P - Black $187.00
Accessories
50-13507 C120MOUNT Ceiling/wall bracket Black 22.99
50-13508 MSC0016 ¼" jack cover Black 0.49
NEW!
Coliseum Series
6 ½" Indoor/Outdoor
Speakers
4 Available with or
without 70V transformer
The Coliseum C130 is a high-end, water resistant speaker featuring specially treated drivers and a sculpted ABS plastic enclosure. This compact speaker is ideally suited for many applications: commercial installations, home theatre, home stereo, mobile applications, reference monitor, personal stage monitor, etc. Features: •Pivoting tweeter •Power handling: 100W RMS •Frequency response:
85Hz~19KHz •Microphone stand mountable
•U-bracket included •Paintable enclosure Inputs: Push terminals and ¼" •Dimensions (H x W x D): 11 ½" x 8 ½" x 7 ½" •#50-13508 protects ¼" jacks from the elements when not in use •Sold individually
Order # Mfr. # Description Color ONLY
Indoor/Outdoor Speakers
50-13515 C130
50-13516 C130W
-
-
Black
White
Indoor/Outdoor Speakers with 70V Transformer
$107.00
107.00
50-13520 C130/70
50-13521 C130W/70
-
-
Black
White
Accessories
50-13508 MSC0016 ¼" jack cover Black
117.00
117.00
0.49
#50-13542
NEW!
Coliseum
Mini Series
5" Ceiling Speaker
4 70V or 8ohm
The CM5/70 is a 30W 5" performance ceiling mount loudspeaker ideal for any background music or paging system where superior sound quality is a priority. Features: 70V taps:
5W, 10W, 20W and 8ohm •Power handling: 30W RMS
•Frequency response: 150Hz~20KHz •Sold individually
Order #
50-13545
ONLY
$23.99
NEW!
8" Active Indoor/Outdoor ABS Speaker
4 100W RMS
The C170P is a compact 100W loudspeaker enclosure made from ABS plastic with an 8" driver and
1"Mylar tweeter. The C170P also features controls for gain, volume and tone, with a switchable mic/line input sensitivity, and a power switch. Features: •Wall or ceiling mount “U” bracket included •Power output
(RMS): 100W •Frequency response: 60Hz~20KHz
•Input: ¼" •Dimensions: 16¼" (H) x 9¾" (W) x 11¼" (D) •Sold individually
Order #
Speakers
50-13540
50-13541
1 3 ⁄
8
" pole mount
50-13542
Color
Black
White
Black
ONLY
$283.00
283.00
8.07
8" Indoor/Outdoor ABS Speaker
4 70V or 8ohm
NEW!
The C170 is a compact 100W loudspeaker enclosure made from ABS plastic with an 8" driver and 1" Mylar tweeter. Integrated 70V transformer allows multiple
C170’s to be connected together without danger of overloading the power amplifier due to impedance drop.
Features: •Wall or ceiling mount “U” bracket included
•70V transformer taps: 6W, 12.5W, 25W or bypass
•Power handling (RMS): 100W •Frequency response:
60Hz~20KHz •Inputs: Binding posts and ¼" •Output
(for 70V system): ¼" •Dimensions: 16 ¼" (H) x 9 ¾" (W) x 11 ¼" (D) •Sold individually
Order #
Speakers
50-13535
50-13536
1 3 ⁄
8
" pole mount
50-13542
Color
Black
White
Black
ONLY
$147.00
147.00
8.07
NEW!
Coliseum Series
4" Enclosed
Ceiling Speaker
Ideal for any paging or background music system, the C160W is a 10W, 4" diameter flush mount-ceiling speaker designed specifically for quick and simple installation in office and retail environments. Features:
•Built-in 70V transformer and taps at 2.5W, 5 or 10W
•Power handling: 10W RMS •Frequency response:
100Hz~16KHz •Sold individually
Order #
50-13525
ONLY
$23.99
18
Order #
50-7885
Outdoor Volume Control
Specifically designed for outdoor applications, this volume control features a specially designed gasketed PVC enclosure, and is ideally suited for use with landscaping “rock” speaker and other outdoor systems. The housing attaches to standard
3
⁄
4
" PVC conduit for simplified watertight installation. Internal jumpers are provided for x1, x2, x4, x8 and x16 impedance multipliers, allowing compatibility in standard and impedance matched installations. Features
•Detachable screw terminal strips accept up to 14AWG speaker cable •12 step attenuation
•May be anchored by PVC conduit alone or with the four attached wall mount tabs •Gray PVC enclosure with matching knob Specifications •Power capacity: 100W RMS •Frequency response: 35Hz~20KHz •Enclosure dimensions: 4
3
⁄
4
" (H) x 3" (W) x 3
1
⁄
4
" (D)
MSRP
$74.95
ONLY
$48.99
www.
MCM electronics.com /
1-800-543-4330
Follow us on: &
8" Two Way Outdoor
“Rock” Speaker
These simulated rocks will add a distinctive look to any outdoor landscaping arrangement, while providing outstanding music fidelity. Fully sealed enclosures are designed to provide years of trouble free service, and may be permanently installed and exposed to weather year round. Features: •70W RMS power capacity •8" injected polypropylene cone woofer
•25mm mylar tweeter •High-quality 12dB crossover
•55Hz~20KHz frequency response •88dB sensitivity
•8ohm impedance •Dimensions: 13.39" x
11.03" x 12.21"
Order #
50-10540
MSRP
$109.00
ONLY
$90.99
Indoor/Outdoor
Speaker with 70V
Transformer
Full range speaker is compatible with conventional 8ohm home audio, as well as commercial 70V distributed systems.
Treated dual cone driver provides outstanding sound quality with high immunity to moisture and humidity.
It is perfect in home or commercial installations, for background music, paging, and general public address applications on patios, poolside, outdoor restaurants etc. Included heavy duty mounting bracket allows easy wall, floor or ceiling mounting, and unique dispersion lens provides even 360° sound distribution. Recessed rotary switch allows easy selection of multiple transformer taps, 8ohm position fully bypasses transformer, allowing maximum frequency response in home systems. Specifications: •Power capacity: 20W
RMS •Frequency response: 80Hz~20KHz (excluding transformer) •Transformer taps: 2.5W, 5W, 10W, 20W
•SPL: 90dB 1W/1M •Driver: 6
1
⁄
2
" dual cone •Magnet size: 10 oz. •Dimensions: 8" (dia.) x 10" (H)
Order #
50-572
MSRP
$69.95
ONLY
$41.49
Weather Resistant Foreground/
Background Speaker Pair
✔ 4" woofer
✔ 6ohm use only
✔ Includes mounting brackets
This quality speaker pair is ideal for use on decks, patios, automobiles or in surround sound applications.
Included “U” brackets allow easy mounting on walls or from the ceiling. Moisture and weather resistant housing, and polypropylene components allow use indoors or out. 4" long excursion woofer, 2" midrange and
3
⁄
4
" tweeter offer 90Hz~20KHz frequency response,
25W/40W RMS/peak power capacity and 85dB sensitivity. Dimensions: 7
3
⁄
8
" (H) x 4
5
⁄
8
" (W) x 4
5
⁄
8
"
(D). 4~8ohm compatible. Nominal impedance
6ohm. Sold in pairs.
Order #
50-5995
50-5996
Color
Black
White
ONLY
$33.49
33.49
AUDIO/VIDEO
Whole House Audio
Section
01
6½" Two Way Outdoor
“Rock” Speaker
These simulated rocks will add a distinctive look to any outdoor landscaping arrangement, while providing outstanding music fidelity. Fully sealed enclosures are designed to provide years of trouble free service, and may be permanently installed and exposed to weather year round. Features: •60W RMS power capacity
•6 1 ⁄
2
" injected polypropylene cone woofer •13mm mylar tweeter •High-quality 6dB crossover •60Hz~20KHz frequency response •87dB Sensitivity •8ohm impedance
•Dimensions: 11.02" x 10.63" x 12.60"
Order #
50-10535
MSRP
$89.95
ONLY
$68.49
5¼" Two Way Outdoor
“Rock” Speaker
These simulated rocks will add a distinctive look to any outdoor landscaping arrangement, while providing outstanding music fidelity. Fully sealed enclosures are designed to provide years of trouble free service, and may be permanently installed and exposed to weather year round. Features: •50W RMS power capacity •5¼" injected polypropylene cone woofer •13mm mylar tweeter •75Hz~20KHz frequency response •87dB sensitivity •8ohm impedance
•Dimensions: 9.64" x 10.25" x 9.05"
Order #
50-10530
MSRP
$59.95
ONLY
$56.99
NEW!
Three-Way Indoor/
Outdoor Speaker Pair
These versatile speakers are designed to be used either indoors or outdoors.
Wide frequency response makes these suitable in main, satellite or monitor speaker situations. Features:
•Fully weatherproof design •Includes mounting brackets
•4" polypropylene cone woofer
•2" polycarbonate dome midrange
• 3 ⁄
4
" mylar dome piezoelectric tweeter
Specifications: • Power capacity: 20W/40W RMS/peak at 8ohm •Frequency response: 90Hz~20KHz
•Dimensions: 7 3 ⁄
8
" x 4 5 ⁄
8
" x 4 3 ⁄
8
"
Order #
50-10545
50-10546
Color
Black
White
MSRP
$39.99
39.99
ONLY
$28.49
28.49
Indoor/Outdoor
Speaker Pair
Compact speakers are ideal for use with a subwoofer in a compact home theater arrangement, or as satellites in remote locations including the patio, deck or near the pool. The fully weatherproof ABS housing, polypropylene cone woofer and mylar tweeter enable permanent mounting outdoors. Mounting brackets and hardware are included. Specifications: •Power capacity: 30W/50W RMS/peak each •Frequency response: 55Hz~20KHz •Impedance: 8ohm
•Dimensions: 7
1
⁄
4
" (H) x 4
1
⁄
2
" (W) x 4
3
⁄
8
" (D)
•Available in black or white •Sold in pairs
Order #
50-6580
50-6581
Color
Black
White
ONLY
$71.49
71.49
Single Stereo Indoor/
Outdoor Speaker
Often times a pair of outdoor speakers is impractical or undesired.
In some areas, actual stereo imaging may not be a possibility, yet both channels need to be heard. This speaker features a dual voice coil woofer and two tweeters, allowing it to provide both left and right channels from a single point. Highly versatile speakers include a base stand for bookshelf use, and a “U” bracket for wall mounting. Their rugged enclosures and stainless steel hardware make these suitable for indoor or outdoor use. Features: •6
1
⁄
2
" poly woofer with rubber surround
•Dual 13mm mylar tweeters •Gold plated connections
Specifications: •Power capacity: 40W RMS (each channel) •Frequency response: 60Hz~20KHz
•Sensitivity: 88dB (W/M) •Impedance: 8ohm (each channel) •Dimensions: 13" (H) x 7
5
⁄
8
" (W) x 7" (D)
•Sold individually
Order #
50-4672
50-4673
Mfr. #
BA-650-OSB
BA-650-OSW
Color
Black
White
ONLY
$107.00
107.00
Indoor/Outdoor
Speaker Pairs
Highly versatile speakers include a base stand for bookshelf use, and a
“U” bracket for wall mounting. Their rugged enclosures and stainless steel hardware make these suitable for outdoor use, while the superior quality components provide outstanding performance expected of a pair of bookshelf speakers. Features: •6
1
⁄
2
" poly woofer with rubber surround •13mm mylar tweeter
•Gold plated connections Specifications: •Power capacity: 50W RMS •Frequency response:
55Hz~20KHz •Sensitivity: 89dB (W/M) •Impedance:
8ohm •Dimensions: 13" (H) x 7
5
⁄
8
" (W) x 7" (D)
•Sold in pairs
Order #
50-4671
Mfr. #
BA-650OW www.
MCM electronics.com /
1-800-543-4330
Color
White
ONLY
$80.99
19
Section
01
AUDIO/VIDEO
Whole House Audio
15" In–Wall LCD Video Monitor
Flat panel LCD monitor mounts flush in virtually any wall, for sleek high end custom installations. Its slim design requires just over 1" depth, and included mounting flange allows easy attachment to standard drywall. White trim bezel provides attractive finished look. Composite video and VGA inputs allow use with whole house A/V systems as well as security applications. •Includes: IR remote •4:3 aspect ratio
•1024 x 768 resolution •PAL/NTSC compatible •400:1 contrast ratio •Requires 12VDC, optional AC adapter available •Mfr. #PLVW15IW
Order #
50-13740
ONLY
$218.00
17" In–Wall Wide Screen LCD Video Monitor
Flat panel LCD monitor mounts flush in virtually any wall, for sleek high end custom installations. Its slim design requires just over 1" depth, and included mounting flange allows easy attachment to standard drywall. White trim bezel provides attractive finished look. Composite video and VGA inputs allow use with whole house A/V systems as well as security applications. •Includes: IR remote •16:9 aspect ratio
•1280 x 800 resolution •PAL/NTSC compatible •300:1 contrast ratio •Requires 12VDC, optional AC adapter available •Mfr. #PLVW17IW
Order #
50-13745
ONLY
$288.00
19" In–Wall Wide Screen LCD Video Monitor
Flat panel LCD monitor mounts flush in virtually any wall, for sleek high end custom installations. Its slim design requires just over 1" depth, and included mounting flange allows easy attachment to standard drywall. White trim bezel provides attractive finished look. Composite video and VGA inputs allow use with whole house A/V systems as well as security applications. Includes: •IR remote •16:9 aspect ratio
•1440 x 900 resolution •PAL/NTSC compatible •300:1 contrast ratio •Requires 12VDC, optional AC adapter available •Mfr. #PLVW19IW
Order #
50-13750
ONLY
$339.00
10.4" In–Wall LCD Video Monitor
Flat panel LCD monitor mounts flush in virtually any wall, for sleek high end custom installations. Its slim design requires only 1" depth, and included mounting flange allows easy attachment to standard drywall.
White trim bezel provides attractive finished look.
Composite video and VGA inputs allow use with whole house A/V systems as well as security applications. •Includes: IR remote •4:3 aspect ratio
•640 x 480 resolution •PAL/NTSC compatible •300:1 contrast ratio •Requires 12VDC, optional AC adapter available •Mfr. #PLVW10IW
Order #
50-13735
ONLY
$197.00
9.2" In–Wall Wide Screen LCD Video Monitor
Flat panel LCD monitor mounts flush in virtually any wall, for sleek high end custom installations. Its slim design requires just over 1" depth, and included mounting flange allows easy attachment to standard drywall. White trim bezel provides attractive finished look. Composite video and VGA inputs allow use with whole house A/V systems as well as security applications. •Includes: IR remote •16:9 aspect ratio
•640 x 234 resolution •PAL/NTSC compatible •300:1 contrast ratio •Requires 12VDC, optional AC adapter available •Mfr. #PLVW9IW
Order #
50-13755
ONLY
$157.00
Stereo Receivers with
DVD Player and USB Reader
4 AM/FM tuner
4 Two microphone inputs
Combining the capabilities of a DVD player, CD player,
AM/FM tuner, powerful amplifier, and the ability to read MP3s directly from a thumb drive, these versatile receivers are ideal for any home or commercial installation. Features: •Auxiliary and MP3 input •Two subwoofer line audio outputs •Component, RCA, and
S-Video outputs •A/B speaker switch •Can read MP3 files stored on a USB thumb drive (navigation via attached television) •DVD/CD/VCD/CD-R/CD-RW support •Two ¼" microphone inputs •50 AM/FM station presets •Remote control included •19" rack mount ears included •AM/FM antennas included
•Dimensions: 17" (W) x 5" (H) x 12" (D)
Order #
50-10640
50-10645
Mfr. #
PD1000A
PD3000A
Power Handling (RMS) ONLY
100W x 2 channels $216.00
300W x 2 channels 272.00
20
Stereo Receiver
Basic function stereo receiver is perfect in applications where 5.1 or 7.1 systems are not required. Designed for home environments, it is also ideal background music in small commercial environments for background music, where up to four speakers are to be used. Amplifier provides 150W x 2Ch max output, and has four audio inputs, including one magnetic phono. AM/FM tuner.
Includes 49 button IR remote. A/B speaker outputs.
Tape in/out. EQ in/out. Mfr. #PT680A.
Order #
50-13785
ONLY
$59.99
Stereo Receiver
Basic function stereo receiver is perfect in applications where 5.1 or 7.1 systems are not required. Designed for home environments, it is also ideal in small commercial environments for background music, where up to four speakers are to be used. Amplifier provides 100W x 2Ch max output, and has three line level inputs. •AM/FM tuner with 50 station memory •Included IR remote
•A/B speaker outputs •Mfr. #PT260A
Order #
555-12090
ONLY
$90.99
www.
MCM electronics.com /
1-800-543-4330
Follow us on: &
Compact Stereo Amplifier
This small amplifier is perfect when multiple line level sources such as a CD, DVD or portable MP3 players need to be connected directly to a pair of speakers.
Features: •Very compact size •Rotary input selector for
CD, Aux1 and Aux2 inputs •L/R RCA line inputs •L/R
RCA tape output •
1
⁄
4
" mic input •Volume, balance, bass and treble controls •Independent mic level control
•Selectable “pager” or “mixer” mode for mic input
•Selectable 110/220VAC power Specifications: •Power output: 8W RMS x 2 channels, 40W x 2 channels max
(4ohm) •THD: 1% •Frequency response: 20Hz~20KHz
•Dimensions: 2.75" (H) x 7.5" (W) x 5.4" (D)
•Mfr. #PTA2
Order #
555-3192
ONLY
$73.99
AUDIO/VIDEO
Whole House Audio
Compact Stereo
Amplifier
This small amplifier is perfect when a line level source, such as a CD or DVD player, or portable MP3 player needs to be connected directly to a pair of speakers. Attached input cable is terminated with male L/R RCA connectors for connection to most devices. Optional RCA to 3.5mm adapter (#24-4590) allows easy connection to headphone output of iPods and similar devices. Features: •Very compact size •Push terminal speaker connections •110/220VAC selectable
Specifications: •Power output: 3W RMS two channels,
15W two channels max (4ohm) •THD: 1% •Frequency response: 40Hz~20KHz •Dimensions: 2.2" (H) x
5.6" (W) x 4.2" (D) •Mfr. #PCA1
Order #
555-3194
ONLY
$36.49
Section
01
Dual Cassette Deck
Dual cassette deck is the perfect addition to any home theater system requiring tape capability. Included mounting hardware also allows the unit to be easily installed in a standard 19" equipment rack. Features:
•Dynamic noise reduction •Normal and high speed dubbing •CrO 2 and normal tape selector •Three digit tape counter •LED level meters • Capability for use with IR remote when used with the matching PT600A integrated amplifier •110/220V switchable power input
•Dimensions (excluding rack ears): 5.5" (H) x 16.5" (W) x 9" (D) •Mfr. #PT649D
Order #
50-6650
ONLY
$108.00
Compact Stereo Amplifier with Mic Input
Small amplifier is perfect when multiple line level sources, such as a CD or DVD players, or portable
MP3 players need to be connected directly to a pair of speakers. Features: •Very compact size •Front panel selector for CD and AUX input • 1 ⁄
4
" microphone input with mic level control •Selectable mic “mix” or mic
“page” modes •Two sets of L/R RCA female input connections • 1 ⁄
4
" front panel headphone jack •Push terminal speaker connections •110/220VAC selectable
Specifications: •Power output: 3W RMS x 2 channels,
15W x 2 channels max (4ohm) •THD: 1% •Frequency response: 30Hz~20KHz •Dimensions: 2.5" (H) x "7.5"
(W) x 5.25" (D) •Mfr. #PTA1
Order #
555-9990
ONLY
$55.99
Compact Stereo Amplifier
Small amplifier is perfect when a line level source, such as a CD or DVD player, or portable MP3 player needs to be connected directly to a pair of speakers. It also ideal when an extra set of in-wall, in-ceiling or outdoor speakers, need to be connected to an existing sound system. Features: •Very compact size with relatively high output power •Five LED bargraph output indicator for each channel •Independent bass and treble controls •L/R RCA female input connections
•Push terminal speaker connections •110/220VAC selectable Specifications: •Power output: 15W RMS x 2 channels, 75W x 2 channels max (4ohm) •THD:
1% •Frequency response: 20Hz~40KHz •Dimensions:
2.5" (H) x 7.5" (W) x 5.5" (D) •Mfr. #PCA3
Order #
555-9980
ONLY
$79.49
Compact Stereo Amplifier
With Mic Input
Small amplifier is perfect when multiple line level sources, such as a CD or DVD players, or portable
MP3 players need to be connected directly to a pair of speakers. It also ideal when an extra set of in-wall, in-ceiling or outdoor speakers, need to be connected to an existing sound system. Features: •Very compact size with relatively high output power •Five LED bargraph output indicator for each channel •Independent bass and treble controls • 1 ⁄
4
" microphone input with mic level control •Selectable mic “mix” or mic “page” modes
•Three sets of L/R RCA female input connections •L/R
RCA female line level record output (fixed level) • 1 ⁄
4
" front panel headphone jack •Push terminal speaker connections •110/220VAC selectable Specifications:
•Power output: 15W RMS x 2 channels, 75W x 2 channels max (4ohm) •THD: 1% •Frequency response:
20Hz~40KHz •Dimensions: 2.5" (H) x 7.5" (W) x 5.5" (D) •Mfr. #PCA3
NEW!
Stereo Ten Band Equalizer
Attractive equalizer provides complete tonal control of L/R stereo audio channels. Each lighted slide allows
±12dB adjustment of ten frequencies between 32Hz and 1.6KHz, at one octave increments. Attractive fluorescent VU meter shows relative output. L/R RCA line level inputs and outputs. •Dimensions 2.2" (H) x
17" (W) x 9" (D) •Mfr. #PPEQ150
Order #
555-12080
Order #
555-12085
ONLY
$65.49
Stereo Ten Band Equalizer
Attractive equalizer provides complete tonal control of L/R stereo audio channels. Each lighted slide allows
±12dB adjustment of ten frequencies between 32Hz and 1.6KHz, at one octave increments. Attractive fluorescent spectrum display shows relative output.
Front panel pushbuttons select from four line level inputs, and two sets of stereo outputs are provided.
•Dimensions 2" (H) x 16.9" (W) x 9.3" (D)
•Mfr. #PPEQ100
Order #
555-12075
NEW!
ONLY
$78.49
Stereo Ten Band Equalizer
NEW!
Attractive equalizer provides complete tonal control of L/R stereo audio channels. Each lighted slide allows
±12dB adjustment of ten frequencies between 32Hz and
1.6KHz, at one octave increments. Attractive multi color
LED spectrum display shows relative output. Front panel pushbuttons select from four line level inputs, and three sets of stereo outputs are provided. •Dimensions 3.5" (H) x 19" (W) x 11.1" (D) •Mfr. #PPEQ200
Order #
555-9995
ONLY
$96.49
Compact Stereo Amplifier
Small amplifier is perfect when a line level source, such as a CD or DVD player, or portable MP3 player needs to be connected directly to a pair of speakers. It is perfect when an extra set of remote speakers, such as in-wall, in ceiling or outdoor, needs to be connected to an existing sound system. Features: •Very compact size
•Independent bass and treble controls •L/R RCA female input connections •Push terminal speaker connections
•110/220VAC selectable Specifications: •Power output:
8W RMS x 2 channels, 40W x 2 channels max (4ohm)
•THD: 1% •Frequency response: 20Hz~40KHz
•Dimensions: 2.5" (H) x 6.25" (W) x 4.75" (D)
•Mfr. #PCA2
ONLY
$121.00
Order #
555-9975 www.
MCM electronics.com /
1-800-543-4330
ONLY
$49.99
21
Section
1
AUDIO/VIDEO
Whole House Audio
NEW!
NEW!
NEW!
Two Channel Compact
Stereo Amplifier
4 120W per Channel @ 4ohm
Small form factor makes this versatile amplifier suitable for many applications, such as distributed audio systems, or even in the shop so you can listen to your
MP3 player. Features: •Power-on LED indicator
•Inputs: RCA L/R, 3.5mm •Master volume control
•Treble and bass level control •Dimensions: 8 ¼" (W) x 2 ¾" (H) x 5 7 ⁄
16
" (D) •Mfr. #PCA4
Order #
50-13705
ONLY
$78.99
30W Compact Stereo
Amplifier with USB Port
4 Plays back MP3 Files
Small amplifier is ideal when a line level source or
MP3 files need to be played through a pair of speakers.
Features: •Reads MP3 audio files from USB thumb drive •Front panel next, previous, and play/pause controls •One RCA L/R input •Master volume control
•Push terminal speaker outputs •Power output: 15W max two channels at 4ohm •Dimensions: 5 5 ⁄
8
" (W) x 2 ¼" (H)x 4 ¼" (D) •Mfr. #PCAU11
Order #
50-13710
ONLY
$40.49
NEW!
NEW!
80W Compact Stereo
Amplifier with USB Port
4 Plays back MP3 files
4 Bass and treble controls
Small amplifier is ideal when a line level source or
MP3 files need to be played through a pair of speakers.
Features: •Reads MP3 audio files from USB thumb drive •Front panel next, previous, and play/pause controls •One RCA L/R input •Master volume control
•Push terminal speaker outputs •Power output: 40W max two channels at 4ohm •Dimensions: 6 ¾" (W) x 2 ¾" (H) x 4 ¾" (D) •Mfr. #PCAU22
Order #
50-13715
ONLY
$54.99
NEW!
150W Compact Stereo
Amplifier with USB Port
4 Plays back MP3 files
4 Bass and treble controls
Small amplifier is ideal when a line level source or
MP3 files need to be played through a pair of speakers.
Features: •Reads MP3 audio files from USB thumb drive •Front panel next, previous, and play/pause controls •One RCA L/R input •Master volume control
•Push terminal speaker outputs •Power output: 75W max two channels at 4ohm •Dimensions: 7 ½" (W) x 2 ¾" (H) x 5 3 ⁄
8
" (D) •Mfr. #PCAU33
Order #
50-13720
ONLY
$80.99
240W Compact Stereo
Amplifier with USB Port
4 Plays back MP3 files
4 Bass and treble controls
4 Front panel 3.5mm input
Small amplifier is ideal when a line level source or
MP3 files need to be played through a pair of speakers.
Features: •Reads MP3 audio files from USB thumb drive •Front panel next, previous, and play/pause controls •One RCA L/R input, one front panel 3.5mm input •Master volume control •Push terminal speaker outputs •Power output: 120W max two channels at
4ohm •Dimensions: 8 ¼" (W) x 2 ¾" (H) x 5 3 ⁄
8
" (D)
•Mfr. #PCAU44
Order #
50-13725
ONLY
$92.99
Compact Stereo
Amplifier with USB Input
Small amplifier is perfect when various line level sources need to be connected directly to a pair of speakers. Mic input with separate level control enables use as small background music amplifier with paging. Built-in USB input accepts standard thumb drives and allows direct reading of MP3 music files. •40W x 2CH max output
•Three line level input selector •Rear panel 1 ⁄
4
" mic input •Front panel 1 ⁄
4
" headphone jack •Independent bass and treble controls •Tape output •Dimensions:
2.7" (H) x 7.4" (W) x 5.4" (D) •Mfr. #PTAU23
Order #
50-13795
ONLY
$77.99
NEW!
NEW!
NEW!
Compact Stereo Amplifier with USB Input
Small amplifier is perfect when various line level sources need to be connected directly to a pair of speakers. Mic input with separate level control enables use as small background music amplifier with paging. Built-in USB input accepts standard thumb drives and allows direct reading of MP3 music files. •75W x 2CH max output
•Three line level input selector •Rear panel 1 ⁄
4
" mic input •Front panel 1 ⁄
4
" headphone jack •Independent bass and treble controls •Dual 5-LED power output indicators •Tape output •Dimensions: 2.7" (H) x
7.4" (W) x 5.4" (D) •Mfr. #PTAU34
Order #
50-13800
ONLY
$96.99
Compact Stereo
Amplifier with USB Input
Small amplifier is perfect when various line level sources need to be connected directly to a pair of speakers. Mic input with separate level control enables use as small background music amplifier with paging. Built in USB input accepts standard thumb drives and allows direct reading of MP3 music files. •120W x 2CH max output
•Three line level input selector •Rear panel 1 ⁄
4
" mic input •Front panel 1 ⁄
4
" headphone jack •Front panel
3.5mmm input •Independent bass and treble controls
•Dual 5-LED power output indicators •Tape output
•Dimensions: 2.7" (H) x 8.3" (W) x 5.4" (D)
•Mfr. #PTAU45
Order #
50-13805
ONLY
$111.00
Compact Stereo
Amplifier with Mic Input
Small amplifier is perfect when various line level sources need to be connected directly to a pair of speakers.
Mic input with separate level control enables use as small background music amplifier with paging. •120W x 2CH max output •Three line level input selector
•Rear panel 1 ⁄
4
" mic input •Front panel 3.5mm input
•Independent bass and treble controls •Dual five-LED output power indicators •Tape output •Dimensions:
2.7" (H) x 8.3" (W) x 5.4" (D) •Mfr. #PTA4
Order #
50-13790
ONLY
$97.99
22 www.
MCM electronics.com /
1-800-543-4330
Follow us on: &
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project