Prism Sound Atlas System information

230W 7R Moving Head Beam
WARNINGS:PLEASE READ THIS CAREFULLY BEFORE USE
1.Inspect the device carefully before installation in case of loose during transportation.
2.Don’t put the product on the shakable or moist place.
3.Please keep the voltage stable, otherwise it will destroy the parts easily.
4.Check the voltage before turning on lamp. While power off, it needs 15minutes to
cool before reconnecting the power.
5.Please keep the lamp dry and cool, .avoid working at 40℃ or above to guarantee its
lifespan.
6.Disconnect the power before installation or removing and ask professional
technician to repair in case of malfunction.
7.Turn on the lock of the Pan and Tilt before turn on the light!
 menu structure
Notice:You can touch the Touch screen or rotate the round button to select the
functions(rotate the round button=UP/DOWN,press the round button=ENTER).
 The main interface
---- Set up
---- Run mode
---- DMX address
---- Channel mode
---- X reversal
----Y reversa
--- XY Encoder
---- No DMX signal
---- Screen saver
---- Power lamp on / off
-- Linear change color wheel
-- Restore Default Settings
-- Manual
-- System
-- Software Version
-- DMX channel value monitoring
-- System Error Log
-- Total time
-- The use of time
-- Total bright bubble time
-- The bright bubble time
-- Advanced -- Reset calibration
-- Maximum light bulbs time
-- Bright bubble time cleared
-- Sensors monitor
-- Chinese / English switch
-- Screen Rotation
 Set
Options
Explanation
DMX
Slave Status: receiving a signal from DMX console or
host
Auto 1
Auto 2
Auto 3
Run mode
Auto 4
Effect 1
Host Status: automatically run and send a signal to the
Effect 2
slave DMX
Effect 3
Effect 4
Random
Run
Sound
Press "OK" button to enter the edit mode. At this point is
to select one hundred and press "up" "down" key to
DMX
1~512
address
change the address code. Press the "OK" button to
select ten editing. Press the "OK" button to select a digit
to edit. Press again to exit edit mode
Standard
Channel
16CH
mode
Extended
Standard 16-channel mode, the first 17
Extended 20-channel mode, the first 17
20CH
X reversal
Y Reversa
to 20
channels control the speed (see channel list)
OFF
ON
OFF
ON
XY
OFF
Exchange
ON
XY Encoder
to 20
channels invalid
Exchange channel XY axes (including trim)
Use encoder (opto) judge out of step and automatically
ON
correct the position
OFF
Without encoder (optocoupler) to correct position
No DMX
Keeping
Original state continues to run
signal
Cleared
Motor return, stop running
ON
Idle 30 seconds after turning off the backlight
OFF
Anthony backlight
Screen saver
Power light
bulbs
Linear
change color
wheel
Directly after power-on reset, no light bulbs (need to use
OFF
the menu or console to manually light bulbs)
Automatically after power light bulbs, and to wait until the
ON
lamp is lit successfully reset
ON
Linear change color wheel
OFF
Nonlinear changes color wheel, half color change
Restore
Press the "OK" button to see the confirmation dialog box,
Default
press the "OK" key to restore the default settings
Settings
manual control
This interface is used to control the current lighting, and automatically enters the host
state (does not receive DMX signals emitted from the machine to the DMX signal to the
bus)。
According to the standard settings menu to manually set menu or extended 16-channel
20-channel mode, the corresponding display 16 channels or 20 channels。
Options
17CH. XY speed
Explanation
0~25
Channel mode is displayed as "extended CH20"
5
18CH. Color wheel speed
0~25
5
Channel mode is displayed as "extended CH20"
19CH Dimmer -. Prism -
0~25
fog, speed
5
20CH. Gobo wheel speed
0~25
Channel mode is displayed as "extended CH20"
Channel mode is displayed as "extended CH20"
5
DMX Channels:
CHANNEL MODE
CHANNE
L
16CH
20CH
1
PAN(X)
PAN(X)
2
TILT(Y)
TILT(Y)
3
PAN FINE
PAN FINE
4
TILT FINE
TILT FINE
5
DIMMER
DIMMER
6
STOP/STROBE
STOP/STROBE
7
COLOR WHEEL
COLOR WHEEL
8
GOBO WHEEL
GOBO WHEEL
9
FOCUS
FOCUS
10
PRISM INSERTION
PRISM INSERTION
11
PRISM ROTATION
PRISM ROTATION
12
FROST
FROST
13
X/Y MOVEMENT SPEED
X/Y MOVEMENT SPEED
14
MARCO FUNCTION
MARCO FUNCTION
15
RESET
RESET
LAMP
16
CONTROL
ON
101-255
OFF
10-100
LAMP
CONTROL
ON
101-255
OFF
10-100
17
----------------------------------------------
PRISM/FROST MAGNIFY
18
----------------------------------------------
COLOR WHEEL SPEED
19
----------------------------------------------
DIMMER-PRISM-FROST TIME
20
----------------------------------------------
GOBO WHEEL SPEED
System Information
Options
Software
Explanation
The current software version
Version
DMX
channel
values
System
Log
Thus entered the sub-interface, numerical and percentage values
for the viewing channel
Error
If the red ERR indicator lights, indicating lamps run error, the details
can thus enter the sub-screen viewing. When you are finished press
the "Clear" button to clear the error log
Note: Sometimes the problem is not really install or optocoupler Hall,
but the motor lines reversed
Total time
Cumulative usage time (accurate to the minute)
The use of time
The boot time since (to the minute)
Total
bright Cumulative bright bubble time (accurate to the minute)
bubble time
The
bright
The light bulb time (accurate to the minute)
bubble time
Options
Explanation
Explanation
Motor
failed,
error
reset Driver board did not respond. Connecting the display panel and the
serial driver board serial communication lines have a problem, or a problem
with the drive plate.
X-axis
reset
X-axis photoelectric switch, or the X-axis motor problems
reset
Y-axis photoelectric switch, or the Y-axis motor problems
fails
X-axis
fails
X-axis
Hall
X-axis Hall problem
Hall
Y-axis Hall problem
error
Y-axis
error
Color
Wheel
Hall color wheel or color wheel motor problems
fail reset
Gobo
reset
Gobo Hall, or gobo wheel motor problems
Focusing reset
Focusing Hall, or focusing motor problems
fails
failed
Prism focusing
Prism focusing Hall, or prism focusing motor problems
reset fails
Lamp
control
Light bulbs or bulbs off failed igniter or bulb problem
bubble
Cumulative time exceeds the maximum bright light bulb bubble time
long,
"Advanced" menu settings, prompts the user to swap guns. After
please change
changing light bulbs clear bubble time in the "Advanced" menu, light
bulbs!
bulbs time to re-timing.
failure
Bright
too
Advanced
Here a layer of password settings to prevent the misuse of non-professionals.Press "OK" key
to enter the password after password verification.
Options
Reset calibration
Explanation
After entering the sub-interface, adjustable reset position X-axis,
Y-axis motor, etc., in order to compensate for the error on the
hardware installation, adjustment range of -128 to +127, +0
means no adjustment.
Maximum
light
0-9999 hours operating time of maximum light bulb will alert
bulbs time
notification system
Bright bubble time
Later cleared, bright bubble time re-timing
cleared
Sensors monitor
Real-time monitoring of light on a variety of photoelectric
switches, Hall sensors, such as state

DIMMER - channel 5
BIT
EFFECT
255
100%
……
……
0
0%

STOP/STOBE - channel 6
BIT
EFFECT
252-255
OPEN
239-251
RANDOM FAST STROBE
226-238
RANDOM MEDIUM STROBE
213-225
RANDOM SLOW STROBE
208-212
OPEN
207
FAST PULSATION
……
……
108
SLOW PULSATION
104-107
OPEN
103
FAST STROBE
……
……
4
SLOW STROBE
0-3
CLOSED

COLOUR WHEEL - channel 7
BIT
EFFECT
Remark
255
FAST ROTATION
……
……
150
SLOW ROTATION
145
BLUE + WHITE
In
140
BLUE
memory, the color value
135
CTB 8000 + BLUE
is always a multiple of 5.
130
CTB 8000
125
CTO 190 + CTB 8000
Linear change:
120
CTO 190
Adjustable color scale, for
115
CTO 260 + CTO 190
example: the value of
110
CTO 260
5:00 Crimson 50% white
105
CYAN + CTO 260
50%, if the number is four
100
CYAN
white Crimson 40% to
95
MAGENTA + CYAN
60%; If the value of 40%
90
MAGENTA
85
YELLOW + MAGENTA
80
YELLOW
75
PINK + YELLOW
70
PINK
65
LAVENDER + PINK
60
LAVENDER
55
LIGHT GREEN + LAVENDER
50
LIGHT GREEN
45
GREEN + LIGHT GREEN
40
GREEN
35
AQUAMARINE + GREEN
30
AQUAMARINE
25
ORANGE + AQUAMARINE
20
ORANGE
15
RED + ORANGE
10
RED
5
WHITE + RED
0
WHITE
order
to
facilitate
for the six white Crimson
60%.
Nonlinear changes:
Adjust colors with color
units.
Color film can be "linear"
and "non-linear" Select
the setup menu.

STATIC GOBO CHANGE - channel 8
BIT
EFFECT
Remark
255
GOBO 17 SHAKE, FAST
Each value corresponds to a pattern of five
SPEED
……
……
251
GOBO 17 SHAKE, SLOW
SPEED
250
GOBO 16 SHAKE, FAST
SPEED
……
……
246
GOBO 16 SHAKE, SLOW
SPEED
……
……
180
GOBO
2
SHAKE,
FAST
SPEED
……
……
176
GOBO 2 SHAKE, SLOW
SPEED
175
GOBO
1
SHAKE,
FAST
SPEED
……
……
171
GOBO 1 SHAKE, SLOW
SPEED
170
FAST ROTATION
……
……
135
SLOW ROTATION
130-134
STOP
129
SLOW ROTATION
……
……
90
FAST ROTATION
85
GOBO 17
80
GOBO 16
75
GOBO 15
70
GOBO 14
65
GOBO 13
60
GOBO 12
55
GOBO 11
50
GOBO 10
45
GOBO 9
40
GOBO 8
35
GOBO 7
30
GOBO 6
25
GOBO 5
20
GOBO 4
Value is always a multiple of 5
15
GOBO 3
10
GOBO 2
5
GOBO 1
0
WHITE

FOCUS - channel 9
BIT
EFFECT
255
100%
……
……
0
0%

PRISM INSERTION - channel 10
BIT
EFFECT
128-255
PRISM INSERTED
0-127
PRISM EXCLUDED

EFFECT
255
FAST ROTATION
……
……
193
SLOW ROTATION
191-192
STOP
190
SLOW ROTATION
……
……
128
FAST ROTATION
0-127
POSITION
EFFECT
128-255
FROST INSERTED
0-127
FROST EXCLUDED
13

Remark
FROST - channel 12
BIT

Remark
PRISM ROTATION - channel 11
BIT

Remark
Remark
Pan-Tilt-TIME- channel 13
Timing Channel
Channel function
Remark
Pan-Tilt time
Pan-Tilt-(Pan fine-Tilt fine)
255
SLOW SPEED
……
……
0
FAST SPEED
MACRO FUNCTION - channel 14
备注
BIT
EFFECT
0-5
UNUSED RANGE
6-15
MARC FUCTION 1
1-15 macro functions act only on the
……
……
color wheel, gobo wheel, prism, prism
146-155
MARC FUCTION 15
rotation.
156-165
AUTO MODE 1
166-175
AUTO MODE 2
Macro function has priority compared
176-185
AUTO MODE 3
to other channels,
186-195
AUTO MODE 4
executing
196-205
AUTO DRAW UP8
channel1,
206-215
AUTO DRAW FORWARD 0
channel6 invalid.
216-225
AUTO DRAW FORWARD STAND8
226-235
AUTO DRAW FORWARD SLEEP8
236-245
AUTO RUN RANDOM MODE
246-255
SOUND CONTROL MODE

the
that is, when
macro
channel2,
function,
channel5,
RESET - channel 15
BIT
EFFECT
128-255
COMPLETE
77-127
Remark
RESET
Reset is activated passing through the unused range and
PAN/TILT
staying 5 seconds.
RESET
26-76
EFFECTS
RESET
0-25
UNUSED
RANGE

LAMP CONTROL- channel 16
BIT
EFFECT
Remark
101-255
LAMP ON
Lamp switch passing through the unused range and staying 5
10-100
LAMP OFF
seconds.
0-9
UNUSED
RANGE

EFFECTS MOVEMENT - channel 17
BIT
EFFECT
--------------------------
---------------------------------
--------------------------
---------------------------------
--------------------------
---------------------------------
--

TIMING CHANNELS
Timing Channel
Channel function
Remark
18
Colour time
Colour wheel
255
SLOW SPEED
19
Beam time
Dimmer-Prism -Frost
……
……
20
Gobo time
Static Gobo
0
FAST SPEED
Specifications:
Voltage: AC100V-240V 50/60Hz
Light source: 230W Osram lamp
Power consumption: 400W
Channel:16/20CHs
Color:14 colors & white
Gobo:17 gobos & open
Strobe:0-10 times/second
X axis: 540 degrees
Y axis: 270 degrees
LCD Touch display: ON/OFF
Protection:IP20 over heat protection
Prism: 8-facet prism
Ballast: electronic ballast
Beam angle: 0-3.8°
Control modes: DMX512,Auto,Sound active,Master/Slave
Carton Packing: 48x44x56 ; GW: 19kg
Please note: Every information is subject to change without prior notice.