ACTi ACM-3001 User`s manual

ACM-3001
IP PoE Fixed Dome Camera
Hardware User’s Manual
(DC 12V / PoE)
Ver. 2012/3/12
ACM-3001 Hardware User’s Manual
Table of Contents
0.
Precautions
3
1.
Introduction
4
Package Contents ........................................................................... 4
Features and Benefits ..................................................................... 5
Safety Instructions .......................................................................... 6
Physical description ........................................................................ 8
Installation Procedure .................................................................. 11
Ceiling Mount ............................................................................... 11
Wall Mount ................................................................................... 14
Basic Connections ......................................................................... 17
Product Specification .................................................................... 18
2.
Accessing Camera
19
If you have DHCP server / router in your network: ...................... 19
If you do NOT have DHCP server / router in your network: ......... 19
2
www.acti.com
ACM-3001 Hardware User’s Manual
0. Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to follow
the safety instruction given may directly endanger people, cause damage to the system or to
other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your local
office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
FCC/CE Regulation
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the users will be required to correct the interference at their own
expense.
3
www.acti.com
ACM-3001 Hardware User’s Manual
1. Introduction
Package Contents
ACM-3001
Product CD
Warranty Card
Accessories
Drill Template
Drill template
4
www.acti.com
ACM-3001 Hardware User’s Manual
Features and Benefits
This is a cutting-edge digital video surveillance camera. It can compress and transmit real time
images with outstanding image quality (30 FPS @ VGA, 640x480) through a standard TCP/IP
network. This camera is your best choice to build an intelligent IP surveillance system.
MPEG-4/MJPEG Dual Codec Compression
This device supports two compression formats, MPEG-4 and MJPEG. It brings superior image
quality at 30 frames per second in resolutions VGA (640 x 480) / QVGA (320 x 240)/ QQVGA
(160 x 112).
Built-in Hardware Motion Detection
No more external motion sensors are required. You may assign up to 3 video motion detection
areas. By tuning the object size and sensitivity, it will reliably detect objects passing though in view.
Hardware motion detection also offers better sensitivity and faster response time than software
motion detection.
Powerful Bundled Surveillance Software
To extend the capabilities of the IP Camera series, a powerful surveillance program is included in
the package for free. Users can easily use an existing PC as a digital video recorder. Scheduled
recording and manual recording keep every important video recorded in the local hard disk.
Reliable and accurate motion detection with instant warning enables immediate response in
every condition. Quick and simple search and playback function lets you easily find the images
and video you want.
Software Development Kit Support
This IP Camera can be integrated or controlled by applications from third party software
developers. Software developers can save considerable efforts by using our Streaming Library or
ActiveX control. Please contact us for details on integration support.
Digital Time Code Embedded
The “Digital Time Code Embedded” function records video time in the video stream. Therefore,
each image frame is marked with its original recording time. It is very useful when users want to
find the video at an exact time or between a certain time intervals.
5
www.acti.com
ACM-3001 Hardware User’s Manual
Safety Instructions
Don’t use the power supply with other voltages
This device is likely to be damaged or damage other equipments / personnel, if you use a power
supply with different voltage than the one included with this device. All warranty of this product will
be voided in the situations above.
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may cause
hazards.
Water and Moisture
Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming pool and the like.
Don’t use accessories not recommended by the manufacturer
Only install this device and the power supply in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in this
manual. Adjust only those controls that are covered by the instruction manual, as an improper
adjustment of other controls may result in damage, and will often require extensive work by a
qualified technician to restore the video product to its normal operation.
6
www.acti.com
ACM-3001 Hardware User’s Manual
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
7
www.acti.com
ACM-3001 Hardware User’s Manual
Physical description
1) Ethernet Port
The IP PoE Fixed Dome Camera connects to the Ethernet via a standard RJ45 connector.
Supporting NWAY, this IP PoE Fixed Dome Camera can auto detect the speed of local network
segment (10Base-T/100Base-TX Ethernet).
2) Power Input
Connect the power adaptor here if your power input is DC12V.
PIN
NAME
DESCRIPTION
1
12V
DC Power Input
2
GND
Ground Pin
3) Reset Button
Step 1: Switch off IP PoE Fixed Dome Camera by disconnecting the power cable
8
www.acti.com
ACM-3001 Hardware User’s Manual
Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen.)
Step 3: Reconnect the power cable while continuing to hold the reset button. The red
Power LED light will flash on for 3 second first, turn off for about 15 seconds, flash on for another
second and turn off again. By this time the reset to default operation is already completed. This
will take around 20 seconds from power up. You may then release the reset button. This
length of time fluctuates slightly with the environment. The Power LED light will come back on
and stay on after a few more seconds. The unit will start up with factory default settings
automatically.
Restore to Default
Complete
Power On
On (3s)
On
1s
Off (about 15s)
Off (10~15s)
Stay On
About 20 Seconds
4) Digital Input / Output *
The IP PoE Fixed Dome Camera supports Digital Input / Output with terminal block connections.
Pushing down the tab above will reveal a small slot for you to insert the end of wire. Release the
tab and the wire will be fastened by the internal spring. The connection pins are as shown in this
image:
Digital Input / Output include the following:
•1 transistor output - For connecting external devices such as relays and LEDs. Connected
devices can be activated by Output buttons on the Live View page or through video management
software.
9
www.acti.com
ACM-3001 Hardware User’s Manual
•1 Digital Input - An alarm input for connecting devices that can toggle between an open and
closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. The device
will detect the change in digital input and transmit the signal to video surveillance servers.
Terminal Pin Define is described as below:
Pin Name
Description
Spec
DIO PW
Electrically connected in parallel with the con-
Voltage: 12V DC,
nector for the power supply, this pin provides an
Max: 1.2W
auxiliary connector for mains power to the unit.
This pin can also be used to power auxiliary
equipment, with a maximum current of 100mA.
DIO GND
Ground
Description
DO
Uses an open-collector NPN transistor with the
Max load = <100mA
(Transistor
emitter connected to the GND pin. If used with an
Max voltage = 24V
Output)
external relay, a diode must be connected in
DC (to the
parallel with the load, for protection against
transistor)
transient voltages.
DI
Connect to GND to activate, or leave floating (or
Must not be
(Digital
unconnected) to deactivate.
exposed to
Input)
voltages greater
than 30V DC.
* Available only for device versions with enhancements
5) Audio Input / Output
The IP PoE Fixed Dome Camera supports Audio input / output with terminal block connections.
Pushing down the tab above will reveal a small slot for you to insert the end of wire. Release the
tab and the wire will be fastened by the internal spring. The connection pins are as shown in this
image:
10
www.acti.com
ACM-3001 Hardware User’s Manual
Installation Procedure
Ceiling Mount
Use the drill template, and drill a hole with φ35 on the ceiling
Tighten the plate to ceiling with M4*20 screws
11
www.acti.com
ACM-3001 Hardware User’s Manual
Connect cables through the hole on the ceiling and plate, or on the side of casing
Fasten the camera to ceiling by turning clockwise direction
12
www.acti.com
ACM-3001 Hardware User’s Manual
Insert the cables (Power/Network/DIO/Audio) through the mounting plate and connect to
the camera. Then use the little strap in bundled accessory to fasten the network cable.
1.6.1.6 Done
13
www.acti.com
ACM-3001 Hardware User’s Manual
Wall Mount
Tighten wall mount bracket to the wall by 3 PAN Head Tapping screws
3-PAN HEAD SCREW TAPPING
Tighten the plate to wall mount bracket with M4*10 screws, and connect all necessary
cables through the hole on the plate and wall mount kit
2-FLAT HEAD SCREW TAPPING(M4x10)
14
www.acti.com
ACM-3001 Hardware User’s Manual
Note: that there’s a triangle mark on both plate and wall mount kit. Those triangle marks
need to be fixed to the same direction.
Insert the cables (power/Network/audio) through the mounting plate and connect to the
camera. Then use the little strap in bundled accessory to fasten the network cable.
15
www.acti.com
ACM-3001 Hardware User’s Manual
Fasten the camera to wall mount kit by turning clockwise direction
Done
16
www.acti.com
ACM-3001 Hardware User’s Manual
Basic Connections
Follow the procedures below to connect the IP PoE Fixed Dome Camera to the respective
apparatuses.
If you have a PoE(Power over Ethernet) supported switch or injector:
1) Connect your IP Camera to the Switch / Injector by CAT5 or CAT6 cables with RJ45
connector.
2) Connect your Switch / Injector to PC with another CAT5 / CAT6 network cable.
If your switch does not support PoE, and you are powering the camera with power
adaptor:
1) Connect the power adaptor to IP Camera
2) Connect IP PoE Fixed Dome Camera’s Ethernet port to Network switch (via RJ45
connectors).
3) Connect a PC to the Ethernet switch (via RJ45 connectors)
17
www.acti.com
ACM-3001 Hardware User’s Manual
Please refer our PoE Guide for more details on Power over Ethernet related concepts.
Product Specification
ACM-3001
Device
Image
Micron Progressive Scan CMOS
Size
1/3 inch
Effective Pixels
Min. Scene
Illumination
640(H) x 480(V)
Color
0.5 Lux at F1.0 (2400 ºK, 30 IRE)
B/W
N/A
IR Sensitivity
N/A
CDS Sensor
N/A
Focal Length
f4.2 mm / F1.8
Viewing Angle
63.7º (Horizontal)
Camera Angle
Adjustment
X (Panning)
Y (Tilting)
0º ~90º
Synchronization
Sync. System
Mechanical IR Cut
Filter
Motion Detection
Internal
Yes (3 Windows)
Electronic Shutter
1/5 ~ 1/15,000 sec
Day/Night Functions
0º ~170º
N/A
Fixed Shutter (Manual)
Functions
AGC
White Balance
S/N Ratio
1/30 ~ 1/1,000 sec. (60Hz); 1/25 ~ 1/1,000 sec. (50Hz)
Flickerless
S/N Ratio
1/120 sec. (60Hz); 1/100 sec. (50Hz)
Automatic (User defined)
AUTO, INDOOR1, INDOOR2, OUTDOOR1, OUTDOOR2, HOLD
CURRENT, MANUAL
Better than 44 dB
Compression
Video Compression
MPEG-4 SP, MJPEG selectable
Picture Resolution
VGA (640x480); QVGA(320x240); QQVGA(160x112)
Bit Rate
28K ~ 3M bps
Image Frame Rate
Audio Input
Audio Output
External I/O
Alarm
Casing
Network
Compression
8kHz, Mono, PCM
Audio Line Input
Unbalanced, 1.4Vp-p, 1Vrms, terminal block
Compression
8kHz, Mono, PCM
Audio Line Output
Unbalanced, 1.4Vp-p, 1Vrms, terminal block
Reset Button
Factory default
Digital Input
1, TTL, terminal block *
Digital Output
1, TTL, terminal block *
Mount Types
Surface / Pendant* / Wall* / Corner* / Pole* / Flush*
Ethernet Port
Ethernet (10/100 Base-T), RJ-45 connector
TCP, UDP, HTTP, HTTPS, DHCP, PPPoE, RTP, RTSP, DNS, DDNS,
NTP, ICMP, ARP, IGMP, SMTP, FTP, UPnP
Microsoft Internet Explorer 6.0 or above
Protocol
Web Browser
Software
30 fps at VGA resolution
SDK
Security
Operating
Power
Physical
Approvals
ACTi SDK-10000
Password protection: configured by the administrator
Temperature
-10 ºC ~ 50 ºC (14 ºF ~ 122 ºF)
Power Requirement
PoE (IEEE802.3af) with Class 3
Power Consumption
3.3 W (DC 12V); 4.3 W (PoE)
130 mm x 99 mm (5.12” x 3.90”)
Dimensions (Ø xH)
Weight
350 g (0.7 lb)
Certificate
CE, FCC
* Available only for device versions with enhancements
18
www.acti.com
ACM-3001 Hardware User’s Manual
2. Accessing Camera
If you have DHCP server / router in your network:
Many network server / routers are able to automatically provide IP addresses through DHCP. If
you are using such a network, just plug in your computer and IP Camera into the network and
your IP PoE Fixed Dome Camera will acquire network address by itself. Find and access the
device with our IP Utility program. You may download it at:
http://www.acti.com/product/detail/Software/ACTi_Utility_Suite
If you do NOT have DHCP server / router in your
network:
1. Configure your PC to use the same subnet by changing your PC’s IP address to the
subnet with prefix 192.168.0.XXX. The last number should be anything from 1 to 254
except 100 and other occupied IP addresses. Subnet mask should be 255.555.255.0.
2. The default IP used by this device is 192.168.0.100. Please make sure your PC is
NOT using this address and that no two equipments use the same IP address in
the network.
3. Change your IP address by going to Control Panel ->Manage Network Connections ->
Right click on the connection to change -> Option -> TCP/IP IPv4 Properties.
19
www.acti.com
ACM-3001 Hardware User’s Manual
Please set the settings as below.


IP address: 192.168. 0.xxx

Subnet mask: 255.255.255.0
(NOTE: xxx should be a number
from 1 to 254 except 100, which is
used by the IP PoE Fixed Dome
Camera. Please also make sure that
no two equipments use the same IP
address in the same network.)
4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP:
192.168.0.100
5. When you see the login window, please input default user and password:
Default User: Admin
Password: 123456
6. After logging in, you will see the video from camera. To go to the main menu, click
the ”Setup” button on the top left.
20
www.acti.com
ACM-3001 Hardware User’s Manual
If you are using a single camera, this is enough to access the device.
If you are using multiple devices, you need to change the current device to another unused
IP address, so that when the next device is connected to the network, no two devices use
the same IP. Please perform the following steps.
7. Go to Setup -> WAN Setting
8. Choose Static IP Address.
9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP address
or 192.168.0.100.). If this is not the first device you add to the network, please also avoid
other devices’ IPs.
21
www.acti.com
ACM-3001 Hardware User’s Manual
10. Click “Apply”
11. Please go to Save Reboot, and click ”Apply”. Internet Explorer will close after a few
seconds. This is normal.
12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example,
192.168.0.101). For the second device or more you add into the network, please type the
correct IP.
13. Adjust the video stream by going to Video Setting
22
www.acti.com
ACM-3001 Hardware User’s Manual
23
www.acti.com