Affinity LE3261 User`s manual

Meijer.com
LE3261
USER’S MANUAL
32
32” LED HDTV
Safety Instructions
Meijer.com
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Safety:
TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS ARE INSIDE. REFER TO QUALIFIED PERSONNEL ONLY.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the television.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code
(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the building, as close to the point of the cable entry as practical.
FCC REGULATORY INFORMATION:
This television has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This television generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this television does cause interference
to other electronic equipment, which can be determined by turning the television off and on, then the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and television.
- Connect the equipment into an outlet on a circuit different from that to which the television is connected.
- Consult your dealer or an experienced radio/TV technician for assistance.
1
Any changes or modifications not expressly approved by the party responsible for compliance may void the user’s
authority to operate the equipment.
Meijer.com
Safety Instructions
2
Safety Instructions
Meijer.com
KCPI/Affinity
3
Meijer.com
Introduction / What’s In the Box ........................................................................... 5
Remote Control
Sound Settings
Bass / Treble / Balance ......................................................................................... 18
Surround ............................................................................................................... 18
Audio Language .................................................................................................... 18
Remote Control Battery Install ............................................................................. 6
Remote Control Overview .................................................................................... 7
TV Overview
Side Panel ............................................................................................................ 8
Rear Panel ........................................................................................................... 9
Pedestal Removal / Wall Mounting ...................................................................... 9
Channel Settings
Favorite ................................................................................................................. 19
Show/Hide ............................................................................................................ 19
Channel Label ...................................................................................................... 19
DTV Signal ........................................................................................................... 19
Zoom Modes ........................................................................................................ 19
Table of Contents
Safety Instructions ................................................................................................ 1-3
Table of Contents ................................................................................................. 4
Parental Controls
Installation
Connection to Antenna & Cable / Satellite Box...................................................... 10
Connection to HDMI Inputs ................................................................................... 11
Connection to Component (YPbPr) Input ............................................................. 12
Connection to AV Composite Input........................................................................ 13
Connection to a Personal Computer ..................................................................... 14
Connection to a Receiver / Amp ........................................................................... 15
Initial TV Setup
Initial Setup Wizard ............................................................................................... 16
Parental Lock ........................................................................................................ 20
Parental Control - US ............................................................................................ 21
Parental Control - Canada .................................................................................... 22
Setup Settings
Closed Caption ..................................................................................................... 23
Menu Language .................................................................................................... 23
Clock ..................................................................................................................... 23
Others Settings
Blue Background .................................................................................................. 24
Reset ....................... ............................................................................................ 24
Picture Settings
Contrast ................................................................................................................ 17
Brightness ............................................................................................................. 17
Color ..................................................................................................................... 17
Specifications ..................................................................................................... 26
Tint (AV mode only)............................................................................................... 17
Troubleshooting .................................................................................................. 27
Sharpness ............................................................................................................. 17
Warranty .............................................................................................................. 28
Color Temperature ................................................................................................ 17
4
Introduction
Meijer.com
Thank you for purchasing the energy efficient Affinity LE3261 HD LED television.
It has been designed to enjoy today’s high definition television experience. With a
display resolution of 1,366 x 768 (720p) you are assured of one of the finest quality
televisions available today. View HDTV and digital broadcasts over-the-air when
connected to an antenna. Choose an outdoor antenna for the best possible reception. Visit www.antennaweb.org.
Your television offers both analog and digital inputs including three High Definition
Multimedia Interface (HDMI) interconnects that offer the purest audio and video
digital signal when connected to compatible HD sources (ie: HD set-top box, high
definition blu-ray player or gaming console). Other video inputs include an HD
component, composite, and VGA terminal for connection to a computer. A coaxial
digital audio (SPDIF) jack is included to connect through your home amplifier/receiver to provide a spectacular home theater sound experience.
What’s In The Box
Your new television is an ENERGY STAR certified device which meets energy
saving standards to reduce power consumption and the associated cost of use.
5
We recommend that you read the user manual thoroughly before use to
familiarize yourself with the installation and adjustment options available to
you, thereby enjoying all the features of the LE3261 for many years to come.
LED TV
with
Pedestal Stand
For peace of mind and valuable services, please take a moment to register your
product at www.kcpi.us
The LE3261 package includes the
following items. Save the carton
& packing for future shipping.
•
•
•
•
•
•
Pedestal Base / Hardware
Pedestal Instructions
Remote Control
AAA Batteries (2)
Quick Start Guide
User Manual
• Remote Control
• AAA Batteries x 2
Meijer.com
• Place two (2) AAA batteries into the
compartment with correct polarity.
•
When pointed towards the television, the effective range is approximately 12 feet from the
front of the IR receiver, 30° to the left and right, 20° up and down.
•
To avoid damage from possible battery chemical leakage, remove the batteries if you do
not plan to use the remote control handset for an extended period of time. Do not mix batteries of different age and/or type. Always discard used batteries safely.
•
Do not expose remote control to liquids, direct sunlight or sources of excessive heat.
•
The IR receiver will not work properly if TV is in direct sunlight, the remote control is
pointed off-axis or an object is in the IR path.
• Replace the cover.
Battery Install
• To insert batteries, turn the remote
control over and remove the battery
cover.
Remote Control
Your remote control handset is powered by two (2) AAA type batteries
30°
30°
IR Receiver
NOTE: Improper use of batteries can result in a chemical leakage or explosion.
6
Remote Control
Meijer.com
Functions Using the Remote Control Handset
1. Power – Turn the television display On/Off.
2. Mute – Press to temporarily turn sound off. Press again to resume.
3. Info – Press to view programming information.
4. Numbers / Dash – Select desired TV channel directly. For example: to select digital channel four,
1
2
5
press “4” “-” “1” (4-1).
5. Source – Press to display all input sources on screen.
6
6. Picture Mode – Select from various preset picture modes: Dynamic > Standard > Movie > User
7
7. Sound Mode – Select Dynamic, Standard, Movie or User sound modes.
4
8. Last – Press to select between the current and previously viewed TV channel.
8
9. Sleep – Press to activate the Sleep function to turn off the TV automatically; 5 Min > 10 Min > 15 Min >
30 Min > 45 Min > 60 Min > 90 Min > 120 Min > 180 Min > 240 Min > OFF.
10. Volume + – Adjust volume up.
3
9
13
10
11. Volume - – Adjust volume down.
12
12. qpt uArrows/ MENU – Navigate menus to make selections. Press MENU to display the Main menu.
13. Channel+ – Scan channels up.
Overview
14. Channel+ – Scan channels down.
15. CC – Select closed caption subtitles (if available) OFF > ON > CC on Mute
16. MTS – Press to select an alternate audio language (if applicable)
17. Enter – Press to confirm selection
18. Exit – Press to exit a menu that is displayed.
19. EPG/Guide – Press to review scheduled programming for the current channel viewed.
20. FAV – Press to display a list of favorite TV channels you have added.
21. FAV+ – Press to scan to a higher channel from your list of favorites.
22. FAV- – Press to scan to a lower channel from your list of favorites.
7
NOTE: When using the remote control, point it directly at the TV.
14
11
15
16
17
18
19
20
21
22
Meijer.com
1. Source - After connecting your DVD, cable box, etc., select
the appropriate input source to view. Press the SOURCE button to
display input options.
I
Source Select
TV
AV
TV Overview
Side Panel
Component
HDMI 1
HDMI 2
Stand by - Red light
TV on - Blue light
HDMI 3
IR Receiver
1
2
3
4
5
6
7
2. Menu - Press the MENU button to display menu settings. .
3/4. Channel (CH+ / CH-) - Press the CH+ / CH- buttons to
select a channel in TV mode.
5/6. Volume (VOL+ / VOL-) - Press the VOL+ / VOL- buttons
to adjust volume up or down.
Front & Side Panel
PC
7. Power - Press the POWER button to turn the LCD display ON/
OFF (standby). When the power is on, the green LED illuminates.
The screen image will appear within a few seconds.
8
Meijer.com
Rear Panel
& Pedestal Removal
TV Overview
TV REAR PANEL
5
100x100mm
1
2
3
4
5
1. SPDIF/Coax - Connect an optional coaxial digital cable through a
compatible amp/receiver to enjoy superior audio sound.
2. RF Input - Connect antenna or cable for television reception.
Note: Use an outdoor antenna, cable or satellite for best reception.
3. VGA Input - Connect an optional VGA cable from your personal
computer.
4. PC-Audio Jack- An optional 3.5mm audio cable for sound when using
VGA.
5. HDMI Input - Supports enhanced high definition video and up to 5.1
channel digital audio from one cable.
9
5
6
7
8
9
6. Component YPbPr - Connect to an AV device that features component (YPbPr) video and audio output jacks. NOTE: There is one set of
audio L/R input jacks for use with either your Component YPbPr or AV
installation.
7. Video L/R – AV input - Connect an external device to the composite
VIDEO (Y) and AUDIO (L/R) output jacks found on most video equipment
NOTE: There is one set of audio L/R input jacks for use with either
your Component YPbPr or AV installation.
8. SERVICE - For service technician use only.
9. Headphone - An optional 3.5mm audio cable for headphones.
Meijer.com
Installation
Roof Antenna / Cable Outlet Installation
TV REAR PANEL
How to connect with an indoor or rooftop antenna
• Connect the RF coaxial (75 ohm) cable from your existing roof top
antenna or wall outlet. Finger tighten the F-Connector end to the
RF IN on the rear panel.
•
Tune to TV programming directly from the television tuner.
Ant./Cable
Wall Outlet
F - Connector
Digital Cable / Satellite Set Top Box
Cable / Satellite set top box
TV REAR PANEL
How to connect with Digital Cable / Satellite Set Top Box
• Connect the RF coaxial (75 ohm) cable from the video outlet of your cable /
Satellite box to the RF IN on the TV’s rear panel. Select Ch. 3 or 4 on the TV
and select a channel.
•
Refer to your cable or satellite set top box user manual.
•
See pages 16-17 for TV setup and Channel Auto Scan.
F - Connector to RF out
Connection to
Antenna Cable/Satellite Box
Optional HDMI cable
10
Installation
Meijer.com
Connecting to an HD Set-Top Box, Game Console or Blu-ray Player Using HDMI
TV REAR PANEL
Digital set top box, gaming console,
or blu-ray w/ HDMI interface
HDMI
Optional HDMI cable
For BEST video performance
Connection to HDMI Inputs
Connect to external devices that feature HDMI, an uncompressed, all digital
video / audio interface found on today’s high definition devices. Use of this
pure digital technology offers optimal high definition video and digital audio all
via a single cable.
There is an HDMI input available for use with HD set top boxes, gaming consoles and blu-ray players.
How to Connect HDMI
• From your external device, connect an HDMI cable from the HDMI OUTPUT to the HDMI INPUT on the TV’s rear panel.
How To Use
• Press the SOURCE button on the remote control. Use qp arrow buttons
to highlight the input to view (HDMI 1) then press OK.
Source Select
TV
AV
Component
HDMI 1
HDMI 2
HDMI 3
PC
11
Meijer.com
Installation
Connecting External Equipment to Component Video IN (YPbPr) on
your television
TV REAR PANEL
For BETTER video performance
Optional
Component cables
Connect to external equipment that features component video output jacks
for great performance. Use Component YPbPr component video and audio
inputs with a set top box, gaming console or DVD player.
•
Connect optional component video cables (blue, green, red) from the
video output jacks (Y, Pb, Pr) on your external equipment to the Component YPbPr input on the TV’s rear panel.
•
Connect white/red audio cables for sound from the audio (L/R) output
jacks on your external equipment to the Component YPbPr L/R input on
the TV’s rear panel.
Source Select
TV
AV
Component
HDMI 1
How to Use
• Press the SOURCE button on the TV remote control. Use qp arrow buttons to highlight the input to view (Component) then press OK.
HDMI 2
HDMI 3
Connection to Component
YPbPr Input
How to Connect Component
• When connecting external equipment to your television, match the colors
of the connecting jacks (Video: Blue, Green, Red; Audio: White/Red).
Digital set top
box, gaming console or DVD
PC
12
Installation
Meijer.com
Connecting External Equipment to AV Composite IN on your television
TV SIDE PANEL
Optional cables
For GOOD video performance
Connection to a
Composite Input
Connect to external equipment using optional video and audio cables. Composite
output jacks are available on most set top boxes and DVD players. (Component and
HDMI connections are recommended for best performance, if possible).
How to Connect Composite AV
• When connecting external equipment to your television, match the colors of the
connecting jacks (Video: Yellow; Audio: White/Red).
•
Connect the yellow video cable from the video output jack on your external A/V
equipment (ie: DVD player, set top box) to AV input on the TV’s rear panel.
•
Connect the white/red audio cables for sound from the audio (L/R) output jacks
on your external equipment (ie: DVD Player, set top box) to the AV (L/R) jacks
on the TV’s rear panel.
How to Use
• Press the SOURCE button on the remote control. Use qp arrow buttons to
highlight the input to view (AV) then press OK.
13
Set top box, gaming console, DVD
Source Select
TV
AV
Component
HDMI 1
HDMI 2
HDMI 3
PC
Meijer.com
TV REAR PANEL
Installation
Connecting a Personal Computer with VGA to your television
Optional cables
Recommended computer display resolution:1,920 x 1,080 @ 60 HZ
How to Connect Audio sound
• Connect an optional 3.5mm audio cable from the computer’s mini
audio output jack to the PC-Audio jack on the TV’s rear panel.
How to Use
• Press the SOURCE button on the remote control. Use qp arrow
buttons to highlight the input to view (VGA) then press OK.
NOTE: If your PC uses a standard signal mode, the screen will adjust
automatically.
Source Select
TV
AV
Component
Connection to a
Personal Computer
How to Connect a PC
• Connect using an optional male to male VGA cable from your PC to
the VGA input on the TV’s rear panel.
HDMI 1
HDMI 2
HDMI 3
PC
14
Meijer.com
Installation
Connection to a Home Theater Audio System
TV REAR PANEL
TV REAR PANEL
Optional digital cable
optional cables
For BEST audio performance
Connection to a Home
Theater System
Connecting to a Home Theater System
Dolby Digital can deliver optimal 2-channel stereo or 5.1 surround
sound with five discrete full range channels separate channel for a
subwoofer.
15
Dolby Prologic
Surround Receiver
Front Right
Speaker
Front Left
Speaker
Digital set top box, gaming console or DVD
Center Channel
Dolby Surround
Connection Illustration
Enjoy optimal sound reproduction from your system with a Dolby
Digital amplifier that incorporates a digital coaxial input. Connect an
optional digital cable directly to the television’s COAX audio output
to listen through all inputs except VGA. (VGA input does not support
digital audio)
Connecting to a Stereo
Receiver/Amplifier
How To Setup Digital Output*
• Press the MENU button on the remote control.
Example: Diagram illustrates the connection of audio cables from
your AV equipment to a stereo receiver instead of the audio (L/R)
jacks on the TV’s rear panel.
•
Press the right u arrow button to select SOUND.
•
Press the down q arrow button to highlight Digital Audio Output
type Raw or PCM*
Surround Left
Speaker
Surround Right
Speaker
Enjoy realistic sound from a stereo / receiver amplifier or Dolby Pro
Logic sound system when connected to your AV equipment.
NOTE: When audio cables are connected to a stereo / receiver amplifier, no audio sound will be heard from the TV’s built-in speakers.
How to Use (Video)
Press the appropriate INPUT button on the remote control. Use qp
arrow buttons to highlight the input to view then press OK.
How to Use (Audio)
Select the appropriate input from your audio equipment.
*NOTE: Refer to the User Manual from your home theater equipment for recommended audio settings.
Meijer.com
After connecting your TV antenna or cable wire, turn the television ON. The initial setup wizard will display on-screen. Select your preferred Picture setting followed by antenna options
if you will view local over-the-air TV broadcasts from an antenna. Theses channels will be
stored in the TV tuner memory after performing Auto Channel Search.
TV Setup
Initial Setup Wizard
The wizard will direct you to the TV menu to select antenna options and perform Auto Channel
Scan. Channels found will be stored into the TV tuner memory.
How to Navigate:
•
Press the qp arrow button to highlight Menu Language and select your language of
choice.
•
Press the qp arrow button to highlight Signal Type and select your language of Air or
•
Press the qp arrow button highlight Auto Channel Search and press OK to start scan
*Auto Channel Search may take several minutes to complete.
Notice:
1. Channel scan starts from the analog channels and then ends with digital channels.
2. Channels found will automatically be stored.
3. You may press the MENU button to skip analog or digital channel search
4. You may press the OK button to end Auto Channel Scan.
Initial Setup Wizard
Cable.
16
16
TV Setup
Meijer.com
The PICTURE menu offers options to enhance and refine the picture displayed on your TV based on ambient room light and personal preferences. Adjustment options include contrast, brightness, color, sharpness, color temperature and Advanced Picture Settings.
How to Navigate:
Press the MENU button on the remote control. Navigate using t u arrow buttons to select PICTURE and press the OK button.
• Press the qp arrow button to highlight Picture Settings
In Picture Settings sub menu, press down q arrow button to highlight Picture Mode.
Navigate using the t u arrow buttons to select DYNAMIC > STANDARD > MOVIE >
USER*.
(*Select USER to manually adjust picture setting)
• Press down q arrow button to highlight Brightness. Navigate using the t u arrow
buttons to increase or decrease overall brightness.
Picture Settings
• Press down q arrow button to highlight Contrast. Navigate using the t u arrow
buttons to increase or decrease contrast intensity.
• Press down q arrow button to highlight Color. Navigate using the
t u arrow buttons to increase or decrease color intensity.
• Press down q arrow button to highlight Sharpness. Navigate using the t u arrow
buttons to soften or view crisper edges in the picture.
• Press the qp arrow button to highlight Screen Size. Navigate using the t u arrow
buttons to select Normal, Wide, Cinema, Zoom.
• Press the qp arrow button to highlight Color Temperature. Navigate using the t u
arrow buttons to select Normal, Warm, Cool.
• Press the qp arrow button to highlight Advanced Picture Settings and press the
OK button. Navigate using the qp arrow buttons to adjust Dynamic Contrast, Film Mode,
Noise Reduction, MPEG Noise Reduction.
17
Note: When adjustments are complete, you may select another menu by pressing the Menu button.
Meijer.com
How to Navigate:
Press the MENU button on the remote control. Navigate using t u arrow buttons to select SOUND and press the OK button.
• Press the qp arrow button to highlight Sound Settings
In Audio Settings sub menu, press down q arrow button to highlight Picture Mode. Navigate
using the t u arrow buttons to select DYNAMIC > STANDARD > SOFT > USER*.
(Select USER to manually adjust picture setting)
• Press down q arrow button to highlight Bass. Navigate using the
t u arrow buttons to increase or decrease low frequency intensity.
Menu Adjustments
The AUDIO menu offers options to make sound enhancements while listening through the built-in speakers or to select digital audio options
when connected to a Dolby Digital receiver though a (SPDIF) coaxial digital output.
• Press down q arrow button to highlight Treble. Navigate using the
t u arrow buttons to increase or decrease high frequency intensity.
• Press the qp arrow button to highlight Surround Mode and press the OK button to enable.
• Press the qp arrow button to highlight AVL and press the OK button to enable.
• Press the qp arrow button to highlight Analog Sound and press the OK button. Navigate
using the t u arrow buttons to select Mono, SAP, Stereo.
• Press the qp arrow button to highlight Digital Sound and press the OK button. Navigate
using the t u arrow buttons to select English, Spanish, French.
Audio Settings
• Press down q arrow button to highlight Balance. Navigate using the
t u arrow buttons to adjust sound towards the left or right speaker.
• Press the qp arrow button to highlight Digital Audio Output and press the OK button.
Navigate using the t u arrow buttons to select Off, PCM, Raw.
• Press down qp arrow button to highlight Equalizer Settings and press the OK button.
Navigate using the t u arrow buttons to select Off > Rock > Pop > Jazz > User*.
(*Select USER to manually adjust picture setting)
Note: When adjustments are complete, you may select another menu by pressing the Menu button.
18
Menu Adjustments
Meijer.com
The CHANNEL menu enables you to search, view and edit channels. It is available in TV mode only.
How to Navigate:
Press the MENU button on the remote control. Navigate using t u arrow buttons to select CHANNEL and press the OK button.
• Press the qp arrow button to highlight Channel List and press the OK button to display
channel list. It will show the current channels.
• Press the qp arrow button to highlight Favorite List and press the OK button to display
favorite channel list.
• Press the qp arrow button to highlight Channel Settings and press the OK button to go to
channel setting sub-menu.
• Press the qp arrow button to highlight Signal Type. Navigate using the t u arrow buttons
to select Air or Cable.
Channel Settings
• Press the qp arrow button to highlight Auto Channel Search and press the OK button to
initial auto channel search.
19
Note: When adjustments are complete, you may select another menu by pressing the Menu button.
Meijer.com
How to Navigate:
Press the MENU button on the remote control. Navigate using arrow t u buttons to select PARENTAL and press OK to proceed to
PARENTAL menu.
• Press the qp arrow button to highlight Lock Parental Control and enter your four-digit
passwrd with numeric key 0-9. (Factory default code is “0000”). After unlocking, the items in
parental control menu can be used.
• Press the qp arrow button to highlight V-CHIP and press the OK button to enter V-chip
setting submenu. (Continued on the next page)
• Press the qp arrow button to highlight Change Password and press the OK button to go to
Change Password setting sub-menu.
Menu Adjustments
In the PARENTAL menu, you may block television and movie programming based on TV ratings and Motion Picture Association guidelines.
To gain access and select your preferences within the Parental menu make certain your input is set to TV.
• Press the qp arrow button to highlight Keypad Lock and press the OK button to block or
unblock the TV’s side panel buttons so they can’t be used.
Note: When adjustments are complete, you may select another menu by pressing the Menu button.
Parental Settings
This option allows you to lock or unlock the input source. The source blocked can not be
choosen from input list.
20
Parental Settings
Menu Adjustments
Meijer.com
21
In the PARENTAL menu, you may block television and movie programming based on TV ratings and Motion Picture Association guidelines.
To gain access and select your preferences within the Parental menu make certain your input is set to TV.
• Press OK or u arrow button to
enter US V-chip ratings menu,
which contains two sub-menus:
Movie Rating and TV.
• Block Unrated Show:
Block all the unrated programs.
• Highlight TV, then press the u arrow button to enter
the TV Ratings menu and select your preference.
TV -Y
TV -Y7
TV -G
TV - PG
TV - 14
TV - MA
Appropriate for all children
Appropriate for all children over 7
General Audience
Parental Guidance Suggested
Parents Strongly Cautioned
Mature Audience Only
• Highlight MPAA, then press the u arrow button repeatedly to select your movie rating preference.
G
General Audience
PG Parental Guidance Suggested
PG13 Parents Strongly Cautioned
R
Restricted
NC17 No One Under 17 Permitted
X
Adults Only
Note: When adjustments are complete, you may select another menu by pressing the Menu button.
Meijer.com
• Press OK or u arrow button
to enter CANADA V-chip
ratings menu, which contains
two sub-menus: English
Rating and French Rating.
E
Appropriate for everyone
C
Appropriate for all children
C8+
Appropriate for everyone 8 years old and up
General Audience
PG Parental Guidance
14+ Appropriate for Children over 14 years old
18+ Mature Audience Only
E
G
Appropriate for everyone
General Audience
8 ans+ Appropriate for Children 8 years old and up
13 ans+ Appropriate for Children 13 years old and up
16 ans+ Appropriate for Children 16 years old and up
18 ans+ Mature Audience Only
Note: When adjustments are complete, you may select another menu by pressing the Menu button.
Parental Settings
G
Menu Adjustments
In the PARENTAL menu, you may block television and movie programming based on TV ratings and Motion Picture Association guidelines.
To gain access and select your preferences within the Parental menu make certain your input is set to TV.
22
Setup Settings
Menu Adjustments
Meijer.com
In the SETUP menu you may adjust the TV preferences.
How to Navigate:
Press the MENU button on the remote control. Navigate using t u arrow buttons to select SETUP and press the OK button.
• Press the qp arrow button to highlight Closed
Caption and press the OK button to go to Closed
Caption setting sub-menu.
• Press the qp arrow button to highlight Caption
Display and press the t ubutton to select caption
display on or off.
• Press the qp arrow button to highlight Analog
Caption Type and press the t ubutton to select
caption type: CC1, CC2, CC3, CC4, TEXT1, TEXT2,
TEXT3, TEXT4.
• Press the qp arrow button to highlight Digital
Caption Type and press the t ubutton to select
caption type: Service1, Service2, Service3, Service4,
Service5, Service6.
• Press the qp arrow button to highlight Digital
CC Style and press the t ubutton to select caption
style: Default, Custom. Only in custom mode you can
adjust the digital caption style.
• Press the qp arrow button to highlight Menu
Language and press the t ubutton to select menu
language: English, French, Spanish.
• Press the qp arrow button to highlight Clock and
press the OK button to select Clock adjustments.
(Time Zone, Auto Clock, Setup Time, Day of Week,
Daylight Saving Time.
23
Note: When adjustments are complete, you may select another menu by pressing the Menu button.
Meijer.com
How to Navigate:
Press the MENU button on the remote control. Navigate using t u arrow buttons to select OTHERS and press the OK button.
• Press the qp arrow button to highlight Blue Back and
press the OK button to select blue background on or off. If
the blue background is selected, the TV will display a blue
background when there is no signal.
• Press the qp arrow button to highlight No Signal
Power Off and press the OK button to turn on or off. If
turned on, the TV will shut off after 10 minutes if no signal
is found. We suggest you to turn on this function when
Blue Back is on.
Menu Adjustments
In the OTHERS menu you may adjust the TV preferences.
• Press the qp arrow button to highlight No Operation
Power Off and press the OK button to turn on or off.
If turned on, the TV will shut off after 4 hours of non
opreation time automatically.
Note: In PC mode, the monitor standby and power off
settings depend on the No Signal Off time.
Note: When adjustments are complete, you may select another menu by pressing the Menu button.
Others Settings
• Press the qp arrow button to highlight Audio Only
and press the OK button to activate audio only mode. The
TV will output only sound and the LED will be turned
off. to restore normal playing, hold POWER button for
three seconds.
24
Zoom
Meijer.com
The ZOOM function offers several viewing display options on the 16:9 screen. Press ZOOM to cycle through the following
widescreen settings.
Located in the Picture
Settings Menu
1. NORMAL
Recommended for viewing native widescreen content and
undistorted 4:3 images.
2. WIDE
Stretches certain 4:3 content and may reduce the black bars.
3. ZOOM
Zooms in to fill the screen when viewing widescreen content.
The zoom effect will crop images somewhat.
4. CINEMA
When viewing 4:3 content, Cinema mode will fill the entire
screen eliminating the side black bars. It may also eliminate or
reduce black bars on certain widescreen movies.
25
Meijer.com
LED
Size (inch)
31.6” Diagonal
Digital Compatibility
480i / 480p / 720p / 1080i
Resolution
1,366 x 768
Brightness (cd/m2)
300
Dynamic Contrast Ratio
1200:1
Vertical Viewing Angle (degrees)
176°
Horizontal Viewing Angle (degrees)
176°
Maximum Colors (millions)
16.7M
Power Consumption
< 55W
Power Supply
AC 120V, 60Hz
Dimension with Pedestal Installed
28.2” (W) x 19.4 (H) x 7.8” (D)
Weight with Pedestal
13.8 lbs.
Input Connections
Composite Video / Audio (L/R)
YPbPr / Component
HDMI
RF
SPDIF Coaxial Digital Output
PC/VGA
PC Audio IN
USB (For Technician Only)
Specifications
Display
(1)
(1)
(3)
(1)
(1)
(1)
(1)
(1)
26
Troubleshooting
Meijer.com
27
Check for a possible solution to a symptom before contacting a customer service representative.
Symptom
Remote codes for
cable / satellite box users
No color
Cannot receive certain
channels through the
antenna
TV signal blocked on certain
channels
Possible Solutions
• Call your satellite or cable provider for available codes.
• Check the video installation of your external A/V equipment.
•
•
•
•
Perform Channel Auto Scan to add channels to the TV tuner memory.
For best performance use an outdoor antenna.
Readjust your antenna and retry Channel Auto Scan.
Signal from the TV station may be weak in your area.
• Perform Channel Auto Scan to add channels into the TV tuner memory.
• Check whether the channel is hidden.
• Check parental control settings.
• Restore default settings.
Video noise or choppy picture
• Readjust antenna. Keep TV away from noise sources, neon lights,
and microwave appliances use and outdoor antenna.
No sound
• Check that connected audio cables are completely inserted.
• Verify you have selected the correct audio source from your
amplifier.
• Mute function may be enabled, press mute on the remote.
Black box on screen
• The “Text” option is enabled and no text is available.
• Press the CCD button on the remote control to turn off.
No power
• Check master power switch located on the bottom of tv bezel.
• Re-attach AC plug to wall outlet after 30 seconds.
• Batteries in the remote control may need replacing.
No picture
•
•
•
•
Remote control does not
function
• Replace batteries with new ones.
• Check that battery polarity is correct.
• Point remote directly at the TV’s IR receiver. See page 6.
Digital TV channel signal may be weak, try another channel.
Press INPUT button to verify the desired input selected.
Re-connect the antenna or cable wiring; use an outdoor antenna.
Restore default settings.
Meijer.com
LE3261
For peace of mind and valuable services, please take a moment to register your product at www.kcpi.us
Kith Consumer Products, Inc. (KCPI) expresses the following limited warranty on AFFINITY. This
warranty extends to a new television purchased from an authorized reseller/retailer within the U.S. by the original purchaser or consumer who received the
product as a gift. Retain and provide the original bill of sale (or photocopy) as proof of purchase. It is also recommended that you retain original box and
foam packaging.
Warranty
Limited North American Warranty
Limited One (1) Year Warranty on Parts and Labor
KCPI warrants the parts in this product against defects in material or workmanship for a period of one (1) year from the date of original purchase from
authorized retailers.
Your Responsibility
Warranty service shall be provided when a return authorization number (RMA#) is provided to you. Warranty extends to defects in materials or workmanship
and does not cover cosmetic imperfections, damages incurred during shipment to KCPI, misuse, natural disasters or accidents.
How to Obtain Warranty Service
, call 888-777-0450
representative.
Limitations
As such, it is NOT
a malfunction to view multiple non-performing pixels on your screen. All warranties implied by state law are expressly limited to the duration of the limited
warranties set forth above with the exception of warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other
warranties, guarantees, agreements, etc., with respect to repair or replacement of any parts. KCPI shall not be liable for consequential or incidental damage.
duration, exclusions or limitation of incidental or consequential damages, so the above may not apply.
28
Meijer.com
Meijer.com
Meijer.com