CARE FITNESS ERGOS III - PART 1 Specifications

TEMPUR ERGO System
®
™
COMPLETE REFERENCE GUIDE
© 2010 Tempur-Pedic Management, Inc. 1713 Jaggie Fox Way, Lexington, KY 40511. All Rights Reserved.
TPNA-CRG-TES-0310
TEMPUR ERGO System
®
20-YEAR LIMITED WARRANTY
TEMPUR-PEDIC NORTH AMERICA, INC. (“TEMPUR-PEDIC”) GUARANTEES THAT WE WILL, AT TEMPUR-PEDIC’S OPTION,
REPLACE OR REPAIR PURCHASER’S TEMPUR® ERGO SYSTEM™ IF IT IS DEFECTIVE DUE TO FAULTY WORKMANSHIP OR
MATERIALS, SUBJECT TO THE LIMITATIONS DESCRIBED IN THIS WARRANTY.
YEAR 1 - FULL COVERAGE OF PARTS AND LABOR
Your TEMPUR® Ergo System™ is warranted against defects in the workmanship or materials for a period of one (1) year from the warranty
commencement date. Electronics, electrical components, drive motors and massage motors are included. Upon notice during the first year from the
warranty commencement date, Tempur-Pedic will send replacement parts (at no cost to the purchaser) for any defective part to the purchaser, and
Tempur-Pedic will pay all authorized labor and transportation costs associated with the repair or replacement of any parts Tempur-Pedic determines
to be defective. This one (1) year warranty shall not apply if purchaser does not return any and all defective parts to Tempur-Pedic within 15 days of
purchaser’s receipt of replacement part.
YEARS 2 AND 3 – FULL COVERAGE OF PARTS ONLY
Upon notice during the years two and three (2 - 3) from the warranty commencement date, Tempur-Pedic will offer replacement parts for any
defective part to the purchaser. Electronics, electrical components, drive motors and massage motors are included. This two (2) year warranty shall not
apply if purchaser does not return any and all defective parts to Tempur-Pedic within 15 days of purchaser’s receipt of replacement part. Purchaser shall
bear all service, transportation, labor, and shipping costs related to the delivery and/or replacement of the defective part.
YEARS 4 THROUGH 20 – PRORATED COVERAGE OF PARTS ONLY
Upon notice during the fourth through the twentieth (4 – 20) years from the warranty commencement date, Tempur-Pedic will offer replacement
parts (upon terms and conditions set forth in this paragraph) for any mechanical bed part found to be defective. Electronics, electrical components,
drive motors and massage motors are excluded. Purchaser shall pay 1/17th of the then current replacement cost of the defective part multiplied
by the number of years after three (3) years from the warranty commencement date, and Tempur-Pedic shall bear the remainder of the cost of the
replacement part. This seventeen (17) year warranty shall not apply if purchaser does not return any and all defective parts to Tempur-Pedic within 15
days of purchaser’s receipt of replacement part. Purchaser shall bear all service, transportation, labor, and shipping costs related to the delivery and/
or replacement of the defective part. After the 20th year, purchaser shall bear the entire cost of repair and replacement of all parts and materials,
including labor and transportation.
ADDITIONAL TERMS AND CONDITIONS
This warranty does not apply; (a) to any damage caused by the purchaser; (b) if there has been any unauthorized repair or replacement of the unit’s
parts; (c) if the unit has been mishandled (whether in transit or by other means), subjected to physical or electrical abuse or misuse, or otherwise
operated in any way inconsistent with the operation and maintenance procedures outlined in the Complete Reference Guide, this warranty, and any
other applicable document published or approved by Tempur-Pedic; (d) to damage to mattresses, fabric, cables, electrical cords or items supplied by
Resellers. Contact the Reseller or relevant party for warranty information on these items.; (e) if there has been any unnecessary service calls, including
costs for in-home service calls solely for the purpose of educating the consumer about the unit for finding an unsatisfactory power connection; (g) if
the recommended weight restrictions are not followed (Twin Long, Split/Dual CA King – 300 lbs., Queen – 425 lbs.), the warranty will be void.
Repairs to or replacement of the TEMPUR Ergo System or its components under the terms of this limited warranty will apply to the original warranty
period and will not serve to extend such period.
The decision to repair or to replace defective parts under this warranty shall be made, or case to be made, by Tempur-Pedic at its option and in its sole
discretion.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE PURCHASER. THERE SHALL BE NO LIABILITY ON THE PART OF TEMPUR-PEDIC
FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OR FOR ANY OTHER DAMAGE, CLAIM, OR LOSS NOT EXPRESSLY
COVERED BY THE TERMS OF THIS WARRANTY. THIS LIMITED WARRANTY DOES NOT INCLUDE REIMBURSEMENT FOR INCONVENIENCE, REMOVAL,
INSTALLATION, SETUP TIME, LOSS OF USE, SHIPPING, OR ANY OTHER COSTS OR EXPENSES. TEMPUR-PEDIC MAKES NO OTHER WARRANTY
WHATSOEVER, EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED BY TEMPUR-PEDIC AND EXCLUDED FROM THIS AGREEMENT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to
every purchaser. This warranty gives the purchaser specific legal rights, and the purchaser may also have other rights, which may vary from state to
state. This warranty is valid in all 50 states, Puerto Rico, and Canada. This warranty is valid only for the original purchaser of the product. An original
purchaser is one who purchases the product directly from Tempur-Pedic North America, Inc. or an authorized Reseller of Tempur-Pedic North America,
Inc. If you are not the original purchaser of this product, you take it “as is” and “with all faults.” If you did not purchase this TEMPUR Ergo System
directly from Tempur-Pedic North America, Inc., we will require proof of purchase from you demonstrating that you are the original purchaser and
eligible to make a valid claim under this warranty. This warranty begins on the “warranty commencement date” which is the date of purchase for new
unused units, and the date of manufacture for units that have been used as floor or display models. Thus, on a floor model unit, the warranty is a
portion of the limited 20-year warranty. If original proof of purchase is not provided by purchaser, Tempur-Pedic reserves the right to determine if the
unit is not covered by this warranty or to use the manufacturing date as the warranty commencement date. This limited warranty gives you specific
legal rights. You may also have other rights that vary from state to state.
If you experience any trouble with your TEMPUR Ergo System during the warranty period, please consult the troubleshooting section of your Reference
Guide. If problems persist after following these instructions, please call: 1-800-979-1457
PLEASE RETAIN THIS WARRANTY AND YOUR ORIGINAL PROOF OF PURCHASE FOR AT LEAST 20 YEARS FROM THE DATE OF PURCHASE.
2
™
TEMPUR ERGO System
®
™
Table of Contents
SAFETY PRECAUTIONS .............................................................................................. 4
COMMONLY ASKED QUESTIONS AND ANSWERS .................................................... 8
SPECIFICATIONS......................................................................................................... 9
INSTALLATION ......................................................................................................... 10
OPERATION
WIRED REMOTE CONTROL FEATURES .............................................................. 18
TROUBLESHOOTING ................................................................................................ 19
SERIAL NUMBER:
Customer Service: 1–800–979–1457
3
TEMPUR ERGO System
®
SAFETY PRECAUTIONS
WARNING!
IMPORTANT SAFETY
INSTRUCTIONS.
PLEASE READ THESE
INSTRUCTIONS
THOROUGHLY BEFORE
USING THIS PRODUCT.
• Keep the cord away from heated surfaces.
SAVE THESE INSTRUCTIONS!
foot support (or other similar parts).
provide you with the reliable operation and durability you
Risk of electric shock — Connect this furnishing to a
Your TEMPUR® Ergo System™ has been designed to
expect. This product has been inspected and tested prior
• Never operate the furnishing with the air openings blocked.
Keep the air openings free of lint, hair and the like.
• Never drop or insert any object into any opening.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are
being used or where oxygen is being administered.
• To disconnect, turn all controls to the off position, then
remove plug from outlet.
WARNING:
Risk of Injury — Keep children away from extended
WARNING!
properly grounded outlet only. See Grounding instructions.
to shipment.
When using an electrical furnishing, basic precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING YOUR
TEMPUR® ERGO SYSTEM™
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction
or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric
shock. This product is equipped with a cord having an
DANGER:
equipment-grounding conductor and a grounding plug.
To reduce the risk of electric shock
• Always unplug this furnishing from the electrical outlet
before cleaning.
The plug must be plugged into an appropriate outlet that
is properly installed and grounded in accordance with all
local codes and ordinances.
DANGER
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons:
• Unplug from outlet before putting on or taking off parts.
• Close supervision is necessary when this furnishing is
used by, or near children, invalids, or disabled persons.
• Use this furnishing only for its intended use as described
in these instructions. Do not use attachments not
recommended by the manufacturer.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with
a qualified electrician or serviceman if you are In doubt
as to whether the product is properly grounded. Do not
modify the plug provided with the product — if it will not
fit the outlet, have a proper outlet installed by a qualified
electrician.
• Never operate this furnishing if it has a damaged cord
or plug, if it is not working properly, if it has been
dropped or damage, or dropped into the water. Return
the furnishing to a service center for examination and repair.
SAVE THESE INSTRUCTIONS!
Customer Service: 1–800–979–1457
4
™
Safety Precautions
GROUNDING SAFETY
WARRANTY PRECAUTION!
This product is for use on a nominal 120-volt circuit, and
Do not open control box, motors or wired remote
has a grounding plug that looks like the plug illustrated
control. The warranty is void if these units are tampered
in sketch A (see Figure). A temporary adapter that looks
with. Any repair or replacement of Ergo System parts must
like the adapter illustrated in sketches B and C is able to
be performed by an authorized person.
be used to connect this plug to a 2-pole receptacle as
shown in sketch B if a properly grounded outlet is not
available. The temporary adapter should be used only until
a properly grounded outlet (sketch A) can be installed by a
qualified electrician.
IN-HOME USE AND HOSPITAL DISCLAIMER
Your Ergo System is strictly designed for in-home use
only. It is NOT designed for hospital use and is NOT
designed to meet hospital standards. DO NOT USE this
bed with TENT TYPE oxygen therapy equipment or near
This product is for use on a circuit having a nominal
explosive gases.
rating more than 120 volts and is factory equipped with
WARNING:
a specific electric cord and plug to permit connection to
a proper electric circuit. Make sure that the product is
DO NOT USE NEAR PEOPLE USING OR WEARING
connected to an outlet having the same configuration as
MEDICAL DEVICES. FOR HOUSEHOLD / RESIDENTIAL USE
the plug. No adapter should be used with this product. If
ONLY. DO NOT USE OUTDOORS.
the product must be reconnected for use on a different
This product conforms to UL STD 962
type of electric circuit, the reconnection should be made
by qualified service personnel.
Unauthorized modifications could void the electrical
portion of your warranty. Failure to use a properly
grounded outlet for this product or modification of the
plug will compromise this important grounding safety
feature and may result in electrical shock, electrical fire, or
faulty operation of the product.
FOR BEST RESULTS, YOUR ERGO SYSTEM SHOULD BE
PLUGGED INTO A SURGE PROTECTOR (not included).
Customer Service: 1–800–979–1457
5
TEMPUR ERGO System
®
IMPORTANT SAFETY FEATURES
USER-SERVICEABLE PARTS
Use this furnishing only for its intended use as described
This product is specifically designed to have no
in these instructions. Do not use attachments not
maintenance by you, the user. Therefore, you are
recommended by the manufacturer.
encouraged not to open any motors, alter the wiring, or
If there is an overload weight condition on the head or
adjust, modify or change the structure of the product, as
foot mechanism, the control unit will automatically stop
it will void the warranty.
all functions. Once the excess weight is removed, the
POWER RATINGS:
MODEL NO: T120-24-2
INPUT: AC 120V - 60Hz
OUTPUT: DC 24V
RATED CURRENT : 3A
CONTROL ACTUATOR : 2
control system will automatically allow all functions to
resume operation.
For your safety, the Ergo System is equipped with special
locking casters. In order to prevent the movement of this
product, all four casters should be in the locked position.
This can be accomplished by pushing down the locking
latch on the caster. To resume mobility of the product, lift
the locking latch up. You are strongly encouraged to place
rubber caster cups or carpet squares under the casters
in addition to locking them in place if the product is
The input transformer voltage is AC120V (1 Amp) 60HZ,
and the output voltage is DC24V (3Amp). When there
is a short-circuit, the customer should seek assistance by
contacting customer service at 1-800-979-1457.
roll, they may slide.
SMALL CHILDREN AND
PETS WARNING
CONSUMERS WITH PACEMAKERS
dispose of packaging as it can smother small children
As with any product that produces a vibrating motion, it is
and pets. To avoid injury, children and pets should not
possible that some pacemakers may interpret this motion
be allowed to play on or under the bed. Children should
as a false sense of movement and/or exercise. This may or
not operate this product without adult supervision. Close
may not affect your pacemaker. If you have any concerns,
supervision is necessary when this furnishing is used
please consult your physician.
by, or near children, invalids, or disabled persons.
positioned on a hard surface floor such as hardwood, tile
or linoleum. Although the casters are locked and will not
After your Ergo System has been unboxed, immediately
SAVE THESE INSTRUCTIONS!
Your Ergo System has been designed to provide
you with the reliable operation and durability you
expect. This product has been inspected and tested
prior to shipment.
Customer Service: 1–800–979–1457
6
™
Safety Precautions
PRODUCT RATINGS
INTENDED USAGE
The lift motors in your Ergo System are NOT designed for
The electric adjustable bed should be installed with
continuous use. Reliable operation and full life expectancy
the head board bracket and/or the head of the
will be attained as long as the lift motors do not operate
frame should be positioned close to a wall.
more than two (2) minutes over a eighteen (18) minute
period, or approximately 10% duty cycle. Any attempt
to circumvent or exceed this rating will shorten the life
expectancy of this product and may void the warranty. The
recommended weight restrictions on our Ergo Systems
are as follows: Twin Long, Split/Dual CA King – 300 lbs.,
Queen – 425 lbs. This Ergo System will structurally support
the recommended weight distributed evenly across the
head and foot sections. Maximum weight per person is
250 pounds. This product is not designed to support or lift
this amount of weight in the head or foot sections alone.
NOTE: Exceeding the recommended weight
restrictions could damage your Ergo System and
void your warranty.
For best performance, you should enter and exit the Ergo
System while it is in the flat or fully lowered position.
Customer Service: 1–800–979–1457
7
TEMPUR ERGO System
®
™
Commonly asked Questions and Answers
WHAT IS THE HEIGHT OF THE ERGO SYSTEM BASE?
With standard legs and casters installed, the overall
height is approximately 15" from the floor to the
bottom of the mattress. The distance between the
floor and the bottom edge of the base, with standard
legs and casters installed, is approximately 9".
IS IT POSSIBLE TO RAISE THE HEIGHT OF THE ERGO
SYSTEM BASE?
Yes, you can add up to 4" to the overall height of the
Ergo System by ordering the riser leg set. These include
replacement legs with casters, and come with either an
overall height of approximately 8" or 10". Please note
that the riser leg set replaces the standard leg set that
comes with the Ergo System. They are not used together.
DOES THE ERGO SYSTEM BASE COME WITH
HEADBOARD AND FOOTBOARD ATTACHMENTS?
The Ergo System does not come with headboard or
footboard brackets. Headboard brackets are available
as optional accessories. A footboard cannot be
attached directly to the Ergo System Base. However,
you can use a “freestanding” bed including headboard,
footboard and side rails by placing the complete Ergo
System within the assembled bed. It may be easiest to
assemble the bed around the Ergo System. You should
measure the inside dimensions of the assembled bed
to be sure the Ergo System will fit. One of our riser leg
sets may be required in some cases.
WILL THE ERGO SYSTEM FIT INSIDE EXISTING
FURNITURE?
The Ergo System is designed to fit into most
“freestanding” beds. We always recommend you
measure the inside dimensions of the assembled bed
to be sure the Ergo System will fit. One of our riser leg
sets may be required in some cases.
WHERE IS THE SERIAL NUMBER ON THE ERGO
SYSTEM?
The serial number can be found on the law tag
attached to the cover and on the frame right below
the foot end of the base. It may be easier to see by
lifting the foot section slightly if possible. The serial
number is also located on the Complete Reference
Guide (owner’s manual) shipped with the base.
WHO DO I CALL FOR SERVICE OR SUPPORT IF NEEDED?
Service and technical support is available by calling
our dedicated customer service group at 1-800-9791457. An owner’s manual is included with each base
including other information for making claims.
WHAT IS THE LIFT CAPACITY OF THE ERGO SYSTEM?
Please see the chart below for Tempur-Pedic’s
recommended and approved “total people weight” limits
per the available mattress and Ergo Base combinations.
Total People Weight
Product
Single Base
Dual Bases
OriginalBed
! 500 lbs.
500 lbs. - 1000 lbs.
AdvantageBed
! 500 lbs.
500 lbs. - 1000 lbs.
TEMPUR-Cloud
! 500 lbs.
500 lbs. - 1000 lbs.
ClassicBed
! 500 lbs.
500 lbs. - 1000 lbs.
TEMPUR-Cloud Supreme
! 500 lbs.
500 lbs. - 1000 lbs.
DeluxeBed
! 500 lbs.
500 lbs. - 1000 lbs.
BellaFina Bed
! 500 lbs.
500 lbs. - 1000 lbs.
RhapsodyBed
! 500 lbs.
500 lbs. - 1000 lbs.
TEMPUR-Cloud Luxe
Not Available
Not Available
CelebrityBed
Not Available
Not Available
AlluraBed
Not Available
Not Available
BellaSonna Bed
Not Available
Not Available
GrandBed
Not Available
Not Available
IS AN EXTENDED WARRANTY AVAILABLE?
No.
IS THE WARRANTY ON A FLOOR MODEL
TRANSFERABLE TO ONE OF OUR CUSTOMERS?
Floor models should only be sold in sets to include
both the mattress and foundation. If you choose to sell
a floor model to a customer, the date of manufacture
is the warranty start date.
WHAT ARE THE ELECTRICAL REQUIREMENTS OF
THE ERGO SYSTEM BASE?
During normal operation, the base will typically draw
1.0 Amp of electricity from a normal AC wall outlet. It
is highly recommended that the customer use a power
surge protector (not included with the base).
DOES THE UNIT HAVE AC OR DC MOTORS?
The lift motors used on the Ergo System base are DC
motors. The base’s power supply converts the AC
power from the wall outlet to DC power.
CAN THE TEMPUR® ERGO SYSTEM™ BE USED WITH
ALL ERGO COMPATIBLE MATTRESSES?
No, due to their increased weight and thickness, the
TEMPUR® Advanced Ergo System™ is recommended for
use with the TEMPUR-Cloud™ Luxe, The CelebrityBed
by Tempur-Pedic® and The AlluraBed by Tempur-Pedic®.
The BellaSonna Bed by Tempur-Pedic™ and The
GrandBed by Tempur-Pedic® are NOT Ergo compatible.
Customer Service: 1–800–979–1457
8
Q&A / Specifications
Bed Type
Specifications
A. Frame
width
B. Base
Width
C. Base
Length
Weight
Twin Long
30"
37 1/2"
79"
128 lbs.
Queen
40"
58 1/2"
79"
167 lbs.
Split CA King
30"
35 3/4"
83"
115 lbs.
38 1/10"
62.9˚
19 3/10"
37.9˚
12 1/10"
A
60 1/5"
C
B
4 9/10"
14 2/5"
53 2/5"
Measurements are approximate and based on standard leg with caster.
No Leg
(rest on frame)
Caster Only
Standard Leg Standard Leg
8" Riser Leg
8" Riser Leg
(without caster)
(without caster)
(with caster)
(with caster)
10" Riser Leg 10" Riser Leg
(without caster)
(with caster)
F
F
F
E
F
E
E
E
E
F
E
F
F
F
E
D
D
D
E
D
D
D
D
D) To Frame
0"
2 3/5"
4 1/10"
6 3/5"
6.0"
8 7/10"
7 3/5"
10 1/5"
E) To Base
2 7/10"
5 3/10"
6 9/10"
9 1/2"
8 9/10"
11 1/2"
10 2/5"
13.0"
F) To Mattress
7 7/10"
10 1/5"
11 9/10"
14 2/5"
13 4/5"
16 2/5"
15 3/10"
17 9/10"
Customer Service: 1–800–979–1457
9
TEMPUR ERGO System
®
Installation Instructions
Before discarding any packing materials, check your
A.*
B.*
C.
D.*
E.*
F.
G.*
H.
TEMPUR® Ergo System™ carton and verify the following
items in the parts list are included:
PARTS LIST
A. Wired Remote Control – hardwired to bed (1)*
B. Mattress Retainer Bar (1)*
C. Bed Leg with Caster (4)
D. Retainer Bar Bolt (4)*
E. Retainer Bar Plate (2)*
F. Allen Wrench (1)
G. Y-Cable (For use with King and CA King)*
H. 9-Volt Batteries (2)
*Attached to base
for shipping
Customer Service: 1–800–979–1457
10
™
Installation
STEP 1
STEP 3
Carefully lift your Ergo System out of the shipping
Remove and extend the power cord and wired
carton, keeping the unit top side down. For safety
remote from the frame.
reasons, this should be performed by 2 people.
WARNING! POWER CORDS AND WIRED CORDS
MUST NOT INTERFERE WITH ANY ERGO SYSTEM
MECHANISMS.
STEP 4
Install 9-volt batteries in the control box.
STEP 5
STEP 2
Carefully flip the Ergo System over to the “topside
Attach Ergo System Legs:
Open the accessories box, take out the 4 legs, and
thread them in a clockwise direction into the
up” position and remove the plastic packaging from
the product.
pre-threaded holes in the frame.
NOTE: DO NOT lean the bed against the installed
legs to flip it over.
NOTE: Hand tighten the legs securely to the
frame. Do NOT over tighten. Make sure the legs
.
322412501&.&56$"#$%"&'()*+,)-
are screwed completely into the frame. Legs that
/0&102%
are not securely attached may become unsafe.
/'0$%-.'%&'(%010,$2-%-.'%
DO NOT unscrew a leg to compensate for an
uneven floor.
,$2-0//'(%/'12%-)%4/,5%,-%)*'#3%
NOTE: Your Ergo System is equipped with
special locking casters. In order to prevent the
movement of this product, all four casters should
be in the locked position. You are strongly
encouraged to place rubber caster cups or
.
!"#$%"&'()*+,)-&
!"#$%&'(%)*'#%+,-.)"-%/'0$,$1%010,$2-%-.'%
,$2-0//'(%/'123
carpet squares (not provided)
under the casters in addition
to locking them in place.
Although the casters lock and
will not roll, they may slide.
Customer Service: 1–800–979–1457
11
TEMPUR ERGO System
®
STEP 6
STEP 10
Plug the power cord into a grounded electrical outlet.
Install the Mattress Retainer Bar (B):
Using the Retainer Bar Bolts (D), Retainer Bar Plates
NOTE: An electrical surge protection unit is
(E) and the Allen Wrench (F), fasten the Mattress
recommended (not included).
Retainer Bar upright to the foot of the Ergo System
frame.
STEP 7
This hand unit is a wired unit, and does not require
batteries.
Briefly activate all functions on the wired
remote control to verify that all of the features
are operational. If the bed does NOT operate,
please refer to the TROUBLESHOOTING section
of this manual.
NOTE: Use ONLY a manual Allen Wrench to
install the Retainer Bar Bolts. DO NOT use a
STEP 8
power tool to tighten the bolts. DO NOT over
Return your Ergo System to the flat position by
tighten the mattress retainer hardware!
pressing and holding the Flat button until the Ergo
System base returns to the flat position.
NOTE: If the Ergo System is to be set up without
a headboard, simply place your Tempur-Pedic
mattress onto the frame. Installation is now
complete. If a headboard is to be installed,
proceed to the next page.
NOTE: If the Ergo System is to be used with a
complete headboard, footboard and side rail
combination, assemble the furniture around the
Ergo System base. DO NOT attach the furniture
STEP 9
Detach the Mattress Retainer Bar (B):
to the Ergo System base. DO NOT use slats.
For shipping purposes the Mattress Retainer Bar
comes installed upside down. Using the Allen
Wrench (F) loosen the Retainer Bar Bolts (D) and
remove the Retainer Bar Plates (E) and Mattress
Retainer Bar. Keep all parts for final installation.
Customer Service: 1–800–979–1457
12
™
Installation
HEADBOARD INSTALLATION
NOTE: This step is only needed if installing a
STEP 1
headboard with optional brackets available
Assemble the Headboard Bracket:
separately.
STEP 1A
NOTE: Failure to follow the proper headboard
Use the remote to raise the head of the bed in order
bracket installation instructions may result in
to gain access to the Ergo System frame.
damage to your Ergo System.
WARNING: The bottom of the headboard cross
member must be positioned so that there is
no more than 3 inches between the bottom
of the headboard and the top of the mattress.
Failure to follow this instruction could result in
serious injury or death to a person or pet caught
between the mattress and the headboard.
STEP 1B
Bolt the Leg Clamp Bracket (A) to the leg using the 45L
OPTIONAL PARTS LIST
A. Leg Clamp Bracket (2)
Bracket Bolts (E), and the 5/16" Locking Nuts (G).
B. Inner Headboard Bracket (2)
Repeat for the other side of the frame.
C. Outer Headboard Bracket (2)
D. 40L Bracket Bolt (6)
E. 45L Bracket Bolt (4)
F. 5/16 Inch Washer (12)
G. 5/16 Inch Locking Nut (10)
H. Wrench (1)
I. Allen Wrench (1)
A.
B.
E
C.
D.
E.
E
G
E
F.
G.
H.
I.
E
G
A
Customer Service: 1–800–979–1457
13
TEMPUR ERGO System
®
STEP 1C
Place Bracket Bolts (D) with a 5/16 inch washer (F)
Place the open side of the the Inner Headboard Bracket
through the Outer Headboard Bracket (C) and into
(B) into the open side of the Leg Clamp Bracket (A).
the Inner Headboard Bracket (B). Use 5/16 inch
washers (F) and 5/16 inch nuts (G) and hand tighten
to allow for adjustment.
Place Bracket Bolts (D) with a 5/16 inch washer (F)
through the Leg Clamp Bracket (A) and into the Inner
Headboard Bracket (B). Use 5/16 inch washers (F) and
5/16 inch nuts (G) and hand tighten to allow for
adjustment.
Repeat on the other side.
Repeat for the other side of the frame.
STEP 1E
Ensure the Headboard Bracket is assembled with a
STEP 1D
distance of 1.5 (38.1 mm) to 2 inches (50.8 mm)
Place the open side of the Outer Headboard Bracket
between the edge of the Ergo Base and the
(C) onto the exposed square tube of the Inner
headboard bracket assemblies.
Headboard Bracket (B). This will create a tight fit
between (B) and (C).
Customer Service: 1–800–979–1457
14
™
Installation
STEP 2
STEP 3
Attach your headboard to the Headboard Brackets
Place your Tempur-Pedic mattress on top of your Ergo
following the steps below:
System Base.
STEP 2A
Measure the center-to-center distance of the
mounting holes in your headboard.
STEP 2B
Measure the center-to-center distance of the
mounting holes in the Headboard Bracket Assemblies.
WARNING: Verify the space between the
headboard cross member and the top of the
STEP 2C
If the Headboard Brackets require adjustment, loosen
the bolts that are holding the Outer Headboard
Brackets and move them so that the mounting holes
on the Outer Headboard Bracket align with the
mattress is no more than 3 inches.
Your TEMPUR® Ergo System™ installation is now complete.
Refer to the Remote Control Guide on pg. 18.
mounting holes on your headboard. Reinstall the bolts
on the Outer Headboard Bracket and firmly tighten
using the Wrench (H) and Allen Wrench (I).
STEP 2D
Place your headboard bolts through the mounting
holes on both the Outer Headboard Bracket and your
headboard. Firmly tighten.
Customer Service: 1–800–979–1457
15
TEMPUR ERGO System
®
Pairing Instructions For Joining Two Bases
FOR 2 BASES TO OPERATE WITH 1 CONTROL
STEP 5
Remove the hardwired remote controls and set aside.
Assembling Split Dual Ergo Bases (Base A and Base B) to
Place the spare remote control in a safe place for any
be used together as a single King or CA King system.
future use.
NOTE: the use of “Base A” and “Base B” is for
STEP 6
description purposes only and the beds will not
Remove and extend one of the provided Y-cables
actually be labeled “Base A” or “Base B”
from the base frame.
STEP 7
STEP 1
Plug in the “A” output of the Y-Cable into Base A
Cut the straps on the boxes of Base A and Base B.
STEP 2
Carefully remove the box covers on Base A and Base B.
control port.
STEP 8
Plug in the “B” output of the Y-Cable into Base B
control port.
STEP 3
Before the bases are removed from their boxes, cut
STEP 9
the plastic strapping on each wired remote control
Plug one of the provided hardwired remote controls
and remove the control from the base frame.
into the “Control Input” side of the Y-Cable.
STEP 10
STEP 4
Carefully unplug the control from Base A and Base B.
Route the control cable to your preferred side of the bed.
Emergency Power Down Cycle Instructions
In the event that your TEMPUR® ERGO System™ Base looses power, there is an Emergency Power Down function.
NOTE: This functions is only if there is no power at the Control Box.
STEP 1
Place two (2) new alkaline 9-volt batteries into the Control Box.
STEP 2
Press the “FLAT” Button on the wired remote control until the base fully lowers to the flat position.
NOTE: Lowering the Ergo System Base using this method is slower than the standard process.
Customer Service: 1–800–979–1457
16
™
Installation
Customer Service: 1–800–979–1457
17
TEMPUR ERGO System
®
Wired Remote Control Features
READ ADVISORY INFORMATION IN THE SAFETY PRECAUTIONS SECTION OF THIS GUIDE CAREFULLY BEFORE
USING THIS PRODUCT. THE POTENTIAL FOR ELECTRIC SHOCK EXISTS IF ELECTRICAL COMPONENTS ARE NOT
INSTALLED OR OPERATED PROPERLY.
LED SIGNATURE LIGHT
A. RAISE (+) HEAD SECTION
OF THE BASE
B. RAISE (+) FOOT SECTION
OF THE BASE
C. RETURN ALL SECTIONS
TO THE FLAT POSITION
D. LOWER (-) HEAD SECTION
OF THE BASE
E. LOWER (-) FOOT SECTION
OF THE BASE
Operating Instructions
HEAD AND FOOT ADJUSTMENTS (A, B, D, E)
• Adjusts the Head and Foot sections to the desired
positions. Press until the red LED Signature Light
illuminates and desired position is achieved.
BED “FLAT” BUTTON (C)
• To level the Ergo System to the Flat position,
press until the red LED Signature Light illuminates and
the bed reaches the flat position.
NOTE: An unintentional touch to any button
that does not illuminate the red LED Signature
Light on the wired remote control will cause
the keys to light up without performing the
associated function. Press the appropriate
wired remote control button until the red LED
Signature Light illuminates to activate the
desired function. This feature was installed to
prevent any undesired movement should the
wired remote control be dropped, etc.
Customer Service: 1–800–979–1457
18
™
Operation / Troubleshooting
Troubleshooting
In the event that your TEMPUR® Ergo System™ fails to operate properly, investigate the symptoms and possible solutions
provided in the chart below:
SYMPTOM
Hand control LED will not illuminate or LED
illuminates and appears to be operable but
will not activate the bed.
SOLUTION
• Verify that the power cord is plugged into a working,
grounded electrical outlet. A grounded, electrical
surge protection device is recommended. Test the
outlet by plugging in another working appliance.
• Verify that the wired remote control wire is securely
plugged into the wired remote control port located in
the control unit on bottom of bed or Y-Cable .
• Unplug the power cord, wait 45 seconds and plug it
in to reset the electronic components.
• The electrical circuit breaker may be tripped. Check
the electrical service breaker box to verify.
No features of the TEMPUR Ergo System will activate.
• The surge protection device or electrical outlet is
defective. Test the outlet by plugging in another
working appliance.
• If bed has been paired, confirm that all cables are
properly connected, especially the Y-Cable line that
plugs into the beds control port.
• The Ergo System may be obstructed. Elevate and
check for an obstruction. Remove the obstruction.
Head and/or Foot section will elevate but will
not return to the horizontal (flat) position.
• The head section may be too close to the wall.
• The headboard may be too close the edge of
the mattress. Verify that a 1.5" (38.1mm) to 2"
(50.8mm) distance is between the headboard
brackets and the mattress. Adjust if required.
Customer Service: 1–800–979–1457
19
TEMPUR ERGO System
®
FOR TECHNICAL SUPPORT OR SERVICE,
PLEASE CHOOSE FROM THE FOLLOWING NUMBERS:
QUESTIONS ABOUT YOUR ERGO SYSTEM BASE:
1-800-979-1457
QUESTIONS ABOUT YOUR TEMPUR-PEDIC MATTRESS
OR TO ORDER ERGO SYSTEM ACCESSORIES:
1-800-821-6621
OR VISIT WWW.TEMPURPEDIC.COM
20
™