Samsung BD-E5400 User manual

BD-E5400
Blu-ray™ Disc Player
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Downloaded From DvDPlayer-Manual.com Samsung Manuals
ENGLISH
Safety Information
CLASS 1 LASER product
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lighting flash and Arrowhead within the CAUTION: TO REDUCE THE RISK OF
The explanation point within the triangle
triangle is a warning sign alerting you of
ELECTRIC SHOCK, DO NOT REMOVE
is a warning sign alerting you of important
dangerous voltage inside the product.
COVER (OR BACK) NO USER SERVICEABLE instructions accompanying the product.
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
WARNING
• To reduce the risk of fire or electric shock,
do not expose this appliance to rain or
moisture.
FCC NOTE (for U.S.A)
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on.
The user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect this equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
This class B digital product meets all
requirements of the Canadian Interference Causing Equipment Regulations.
Note to CATV system installer
This reminder is provided to call CATV
system installer's attention to Article 82040 of the National Electrical Code (Section
54 of Canadian Electrical Code, Part I) that
provides guidelines for proper grounding and,
in particular, specifies that the cable ground
shall be connected to the grounding system
of the building as close to the point of cable
entry as practical.
Downloaded
From DvDPlayer-Manual.com Samsung Manuals
2
This Compact Disc player is classified as a
CLASS 1 LASER product. Use of controls,
adjustments or performance of procedures
other than those specified herein may result in
hazardous radiation exposure.
Complies with 21CFR 1040.10 except for
deviations pursuant to Laser Notice No. 50,
dated June 24, 2007.
DANGER :
• VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. AVOID DIRECT
EXPOSURE TO BEAM. (FDA 21 CFR)
CAUTION :
• CLASS 3B VISIBLE AND INVISIBLE
LASER RADIATION WHEN OPEN. AVOID
EXPOSURE TO THE BEAM. (IEC 60825-1)
• THIS product UTILIZES A LASER. USE
OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVER AND
DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1 PRODUCTO
✎✎ NOTE
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
LÁSER CLASE 1
`` If the Region number of a Blu-ray Disc/DVDs
does not correspond to the Region number of
this player, the player cannot play the disc.
Precautions
Important Safety Instructions
Read these operating instructions carefully
before using the unit. Follow all the safety
instructions listed below.
Keep these operating instructions handy for
future reference.
1.
Read these instructions.
3.
Heed all warnings.
2.
4.
5.
6.
7.
8.
9.
Keep these instructions.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including AV
receivers) that produce heat.
Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or
the third prong are provided for your
safety. If the provided plug does not fit
into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where it exits the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart,
stand, tripod, bracket,
or table specified by
the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as when the power-supply
cord or plug is damaged, liquid has
been spilled or objects have fallen into
the apparatus, the apparatus has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
Disc Storage & Management
• Holding Discs
-- Fingerprints or scratches
on a disc may reduce
sound and picture quality
or cause skipping
-- Avoid touching the surface of a disc
where data has been recorded.
-- Hold the disc by the edges so that
fingerprints will not get on the surface.
-- Do not stick paper or tape on the disc.
• Cleaning Discs
-- If you get fingerprints or dirt
on a disc, clean it with a mild
detergent diluted in water
and wipe with a soft cloth.
-- When cleaning, wipe gently
from the inside to the outside of the disc.
• Disc Storage
`` Do not keep in direct sunlight.
`` Keep in a cool ventilated area.
`` Keep in a clean protection jacket and
store vertically.
Handling Cautions
• Do not expose this apparatus to dripping
or splashing. Do not put objects filled with
liquids, such as vases on the apparatus.
• To turn this apparatus off completely, you
must pull the power plug out of the wall
socket. Consequently, the power plug must
be easily and readily accessible at all times.
• Do not plug multiple electric devices into
the same wall socket. Overloading a socket
can cause it to overheat, resulting in a fire.
• Maintenance of Cabinet.
-- Before connecting other components to
this player, be sure to turn them off.
-- If you move your player suddenly from a
cold place to a warm place, condensation
may occur on the operating parts and
lens and cause abnormal disc playback. If
this occurs, unplug the player, wait for two
hours, and then connect the plug to the
power outlet. Then, insert the disc, and try
to play back again.
• If the product makes an abnormal noise
or produces a burning smell or smoke,
turn off the power switch immediately and
disconnect the power plug from the wall
outlet. Then, contact the nearest customer
service center for technical assistance. Do
not use the product. Using the product as
it is may cause a fire or an electric shock.
Copyright
© 2012 Samsung Electronics Co.,Ltd.
All rights reserved; No part or whole of this
user's manual may be reproduced or copied
without the prior written permission of
Samsung Electronics Co.,Ltd.
Downloaded From DvDPlayer-Manual.com Samsung Manuals
Contents
Safety Information
Language Settings...................................... 13
Precautions.................................................. 2
General Settings......................................... 13
Warning........................................................ 2
Disc Storage & Management........................ 3
Security Settings........................................ 13
Support Settings........................................ 13
Handling Cautions........................................ 3
Media Play
Getting Started
Insert a USB Device.................................... 14
Copyright..................................................... 3
Before using the User Manual....................... 4
Logos of Discs the player can play............... 4
Accessories.................................................. 5
Front Panel................................................... 6
Rear Panel.................................................... 6
Remote Control............................................ 6
Connections
Insert a Disc............................................... 14
Controlling Video Playback......................... 15
Controlling Music Playback......................... 15
Playing Photo Contents.............................. 16
Appendix
Troubleshooting.......................................... 16
Specifications............................................. 18
A. Connecting to a TV.................................. 7
B. Connecting to an Audio System............... 7
C. Connecting to a Network......................... 7
Settings
The Initial Settings Procedure....................... 8
Menu Navigation........................................... 8
Accessing the Settings Menu....................... 9
Display Settings............................................ 9
Audio Settings............................................ 10
Network Settings........................................ 10
System Settings......................................... 12
3
Getting Started
Region Code
Before using the User Manual
Disc Types and Contents your player can play
Media
VIDEO
MUSIC
PHOTO
✎✎ NOTE
Disc Type
Blu-ray Disc
DVD-VIDEO
DVD-RW
DVD-R
DVD+RW
DVD+R
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Details
BD-ROM or BD-RE/-R recorded in the BD-RE format.
DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R that have
been recorded and finalized, or a USB storage media containing MKV
or MP4 contents.
Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB
storage media containing MP3 or WMA contents.
Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB
storage media containing JPEG contents.
Both players and discs are coded by region.
These regional codes must match for a disc
to play. If the codes do not match, the disc
will not play.
The Region Code for this player is displayed
on the rear panel of the player.
Disc Type
Region
Code
Blu-ray
Disc
a
DVDVIDEO
North America, Central
America, South America,
Korea, Japan, Taiwan, Hong
Kong and South East Asia.
1
The U.S., U.S. territories and
Canada
Area
Logos of Discs the player can play
`` The player may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.
`` If a DVD-RW/-R has not been recorded properly in DVD video format, it will not be playable.
`` Your player will not play content that has been recorded on a DVD-R at a bit-rate that exceeds 10 Mbps.
Blu-ray Disc
BD-LIVE
`` Your player will not play content that has been recorded on a BD-R or USB device at a bitrate that exceeds
25 Mbps.
`` Playback may not work for some types of discs, or when you use specific functions, such as angle change
and aspect ratio adjustment. Information about the discs is written in detail on the disc box. Please refer to
this if necessary.
`` When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.
Disc types your player cannot play
• HD DVD
• DVD-ROM/PD/
MV, etc
• DVD-RAM
• Super Audio CD
(except CD layer)
• DVD-RW(VR mode) • 3.9 GB DVD-R for
Authoring.
• CVD/CD-ROM/
CDV/CD-G/CD-I/LD
(CD-Gs play audio
only, not graphics.)
Downloaded
From DvDPlayer-Manual.com Samsung Manuals
4
NTSC broadcast system in U.S.A, Canada, Korea, Japan
Supported File Formats
Notes on the USB connection
• Your player supports USB storage media,
MP3 players, digital cameras, and USB
card readers.
• The player does not support folder or file
names longer than 128 characters.
• Some USB/External HDD/digital camera
devices may not be compatible with the player.
• Your player supports the FAT16, FAT32,
and NTFS file systems.
• Connect USB devices directly to the player’s
USB port. Connecting through a USB cable
may cause compatibility problems.
• Inserting more than one memory device
into a multi-card reader may cause the
reader to operate improperly.
• The player does not support the PTP protocol.
• Do not disconnect a USB device during a
“loading” process.
• The bigger the image resolution, the longer
the image takes to display.
• This player cannot play MP3 files with DRM
(Digital Rights Management) downloaded
from commercial sites.
• Your player only supports video with a
frame rate under 30fps (frames per second).
• Your player only supports USB Mass
Storage Class (MSC) devices such as
thumb drives and USB HDD. (HUB is not
supported.)
• Certain USB HDD Devices, multi-card
readers and thumb drives may not be
compatible with this player.
• If some USB devices require excessive
power, they may be limited by the circuit
safety device.
• If playback from a USB HDD is unstable,
provide additional power by plugging the
HDD into a wall socket.
If the problem continues, contact the USB
HDD manufacturer.
• You must remove the USB storage device
safely. (by performing the "Safely Remove
USB" function to prevent possible damage
to the USB memory.)
Press the HOME button to move to the
home screen, press the YELLOW (C)
button, and then press the v button.
• SAMSUNG is not responsible for any data file damage or data loss.
• Your player does not support NTFS compressed files, sparse files, or encrypted files.
• You can repair or format a USB device on your Desktop PC. (MS-Windows OS only)
•• Audio decoder
Video File Support
Music File Support
File Extension
*.avi
Container
AVI
*.mkv
MKV
*.wmv
WMV (wmv9)
*.mp4
MP4
*.mpg
*.mpeg
PS
•• Limitations
Video Codec
MP4v3
H.264 BP/MP/HP
VC-1 AP
H.264 BP/MP/HP
VC-1 AP
VC-1 SM
MP4 (mp4v)
H.264 BP/MP/HP
MPEG1
MPEG2
H.264 BP/MP/HP
Audio Codec
MP3
Dolby Digital
DTS
WMA
PCM
MP3
Dolby Digital
DTS
WMA
AAC
MP1, 2
Dolby Digital
DTS
Resolution
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
-- Even when a the file is encoded by a supported codec mentioned above, the file might not
be played if its content has a problem.
-- Normal playback is not guaranteed if the file’s container information is wrong or the file
itself is corrupted.
-- Files having higher Bit rate/frame rate than standard may stutter during sound/video playback.
-- The Seek (skip) function is not available if the file’s index table is damaged.
•• Video decoder
-- Supports up to H.264 Level 4.1 and AVCHD
-- Does not support H.264 FMO/ASO/RS and VC1 SP/MP/AP L4
-- MPEG4 SP, ASP :
Below 1280 x 720 : 60 frames max
Above 1280 x 720 : 30 frames max
-- Does not support GMC 2 or higher
Downloaded From DvDPlayer-Manual.com Samsung Manuals
-- Supports WMA 7, 8, 9 and STD
-- Does not support WMA sampling rate of 22050Hz mono.
File Extension
*.mp3
*.wma
Container
MP3
WMA
Audio Codec
Support Range
WMA
* Sampling rates (in kHz) - 8, 11, 16, 22, 32, 44.1, 48
* Bit rates - All bit-rates from 5kbps to 384kbps
MP3
-
AVCHD (Advanced Video Codec High Definition)
• This player can play back AVCHD format discs. These discs are normally recorded and used
in camcorders.
• The AVCHD format is a high definition digital video camera format.
• The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the
conventional image compressing format.
• Some AVCHD discs use the “x.v.Color” format. This player can play back AVCHD discs that
use “x.v.Color” format.
• “x.v.Color” is a trademark of Sony Corporation.
• “AVCHD” and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd.
and Sony Corporation.
✎✎ NOTE
`` Some AVCHD format discs may not play, depending on the recording condition.
AVCHD format discs need to be finalized.
`` “x.v.Color” offers a wider color range than normal DVD camcorder discs.
`` Some MKV and MP4 format discs may not play, depending on the video resolution and frame rate condition.
Accessories
Check for the supplied accessories shown below.
Batteries for Remote Control
(AAA Size) (BN43-00004A)
User Manual
(AK68-02273A)
Remote Control
(AK59-00146A)
5
Front Panel
Remote Control
PLAY/PAUSE BUTTON
STOP BUTTON
Tour of the Remote Control
OPEN/CLOSE BUTTON
Turn the player on and off.
POWER BUTTON
Press to eject a disc.
Turn the TV on and off.
After setup, allows you to set the input
source on your TV.
TV volume adjustment.
Press numeric buttons to operate options.
Use to enter the popup menu/title menu.
Use to enter the disc menu.
✎✎ NOTE
REMOTE CONTROL SENSOR
DISC TRAY
`` When the player displays the Blu-ray Disc menu, you cannot start the movie by pressing the Play button
on the player or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and
then press the v button.
Rear Panel
Press to search a disc backwards or
forwards.
Press to pause a disc.
Press to skip backwards or forwards.
Press to stop a disc.
Press to use Netflix.
Press to play a disc.
Press to use Pandora.
Press to move to the home menu.
Press to use Tools menu.
Use to display the playback information
when playing a Blu-ray Disc/DVDs.
Use to select menu items and change menu
values.
Press to exit the menu.
Return to the previous menu.
These buttons are used both for menus on the
player and also several Blu-ray Disc functions.
Allows you to repeat a title, chapter, track or
disc.
Use to access various audio functions on a
disc (Blu-ray Disc/DVD).
Installing batteries
✎✎ NOTE
HDMI OUT
Press to see the full screen on a TV.
Press to switch the Blu-ray Disc/DVD’s
subtitle language.
✎✎ NOTE
USB HOST
`` You can perform software upgrades using the USB Host jack with a USB flash memory stick only.
Downloaded
From DvDPlayer-Manual.com Samsung Manuals
6
!!
`` If the remote does not operate properly:
• Check the polarity (+/–) of the batteries.
• Check if the batteries are drained.
• Check if the remote sensor is blocked by
obstacles.
• Check if there is any fluorescent lighting nearby.
CAUTION
`` Dispose of batteries according to local environmental
regulations. Do not put them in the household trash.
Connections
Connecting to an Audio System (HDMI supported AV receiver)
A. Connecting to a TV
Connecting to a TV with an HDMI Cable
1.
2.
3.
4.
Using an HDMI cable, connect the HDMI OUT terminal on the rear of the player to the
HDMI IN terminal of your TV. See page 8.
Turn on the player and TV.
Press the input selector on your TV remote control until the HDMI signal from the player
appears on your TV screen.
1.
2.
3.
4.
5.
Using an HDMI cable, connect the HDMI OUT terminal on the rear of the player to the
HDMI IN terminal of your AV receiver. See page 8.
Using an HDMI cable, connect the HDMI OUT terminal of the AV receiver to the HDMI IN
terminal of your TV.
Turn on the player, TV, and AV receiver.
Using the input select button of the AV receiver and TV, select the correct HDMI input or
source on each to hear sound and see video from the player. Refer to your AV receiver’s
user manual to set the AV receiver’s audio input.
If this is the first time you have turned on the Blu-ray player, the Initial Settings screen
appears. See page 8.
If this is the first time you have turned on the Blu-ray player, the Initial Settings screen
appears. See page 8.
✎✎ NOTE
`` An HDMI cable outputs digital video/audio, so you don’t need to connect an audio cable.
`` If the player is connected to your TV in the HDMI 720p, 1080i, or 1080p output mode, you must use a
High speed (category 2) HDMI cable.
`` HDMI outputs only a pure digital signal to the TV.
If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on
the screen.
`` Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of
your TV.
`` When you connect the player to the TV using the HDMI cable for the first time or to a new TV, the HDMI
output resolution will be automatically set to the highest supported by the TV.
`` A long HDMI cable may cause screen noise. If this occurs, set Deep Color to Off in the menu.
`` If you use an HDMI-to-DVI cable to connect to your display device, you must also connect the Digital Audio
Out to an audio sytem to hear audio.
B. Connecting to an Audio System
• Please turn the volume down when you turn on the AV receiver. A sudden loud sound
may cause damage to the speakers and your ears.
• Please set the audio format according to the capabilities of your AV receiver.
• The position of HDMI input terminals may vary depending on your AV receiver. Please
refer to the user manual of your AV receiver.
Downloaded From DvDPlayer-Manual.com Samsung Manuals
C. Connecting to a Network
This player lets you use network based services, such as BD-LIVE, and download software
upgrades when it is connected to a network. We recommend using a Broadband modem (with
integrated router) or an IP router for the connection. For more information on router connections,
refer to the user manual of the router or contact the router manufacturer for technical assistance.
Wireless Network
1.
2.
You can connect this unit to a network via a wireless connection. See page 8.
Set the network options. See pages 10~12.
✎✎ NOTE
`` If your wireless router supports DHCP, this player can use a DHCP or static IP address to connect to the
wireless network.
`` Set your wireless router to Infrastructure mode. Adhoc mode is not supported.
`` The player supports only the following wireless security key protocols:
-- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES), WPA2-PSK (TKIP/AES)
`` Select a channel on the wireless router that is not currently being used. If the channel set for the wireless
router is currently being used by another device nearby, it will result in interference and communication
failure.
`` If you select the Pure High-throughput (Greenfield) 802.11n mode and set the Encryption type on your
router to WEP, TKIP or TKIP-AES (WPS2Mixed), the player will not support a connection in compliance with
new Wi-Fi certification specifications.
`` Wireless LAN, by its nature, may cause interference, depending on the operating conditions (router
performance, distance, obstacles, interference by other radio devices, etc).
7
A Connecting to a TV
Settings
The Initial Settings Procedure
B Connecting to an Audio System
HDMI cable
(not included)
HDMI cable
(not included)
`` If you leave the player in the stop mode for
more than 5 minutes without using it, a screen
saver will appear on your TV. If the player is
left in the screen saver mode for more than 25
minutes, the power will automatically turn off.
• The Home screen will not appear if you do not
configure the initial settings.
• The OSD (On Screen Display) may change in this
player after you upgrade the software version.
• The access steps may differ depending on the
menu you selected.
• After the loading process of this product is
finished, the panel buttons and remote control
can be operated.
Menu Navigation
1
The Initial Settings Procedure lets you set
the OSD and menu languages, configure
the connection to your home network, and
choose the aspect ratio output (screen size
and format) that is correct for your TV.
✎✎ NOTE
HDMI cable
(not included)
C Network
Wireless Router
Broadband service
✎✎ NOTE : You can only connect this unit to a network via a wireless connection.
Downloaded
From DvDPlayer-Manual.com Samsung Manuals
8
`` The Home menu will not appear if you do not
configure the initial settings except as noted below.
`` If you press the BLUE (D) button during
network setup, you can access the Home menu
even if the network setup is not completed yet.
`` When you return to the Home menu, the full
screen mode is cancelled automatically.
`` If you want to display the Initial Setting screen
again to make changes, press the @ button on
the front panel of the player for more than 5
seconds with no disc inserted. This resets the
player to its default settings.
`` After the loading process of this product is
finished, you can operate the HDMI-CEC function.
`` If you want to use an Anynet+(HDMI-CEC)
function, please follow the instructions below.
1) Connect the player to an Anynet+(HDMICEC) compliant Samsung TV using HDMI Cable.
2) Set the Anynet+(HDMI-CEC) feature to On in
both the TV and the player.
3) Set the TV to the Initial Settings Procedure.
3
2
1
2
3
4
4
HOME Button : Press to move to the Home
menu.
RETURN Button : Return to the previous menu.
v (Enter) / DIRECTION Button :
Move the cursor or select an item.
Activate the currently selected item.
Confirm a setting.
EXIT Button : Press to exit the current menu.
• Home Menu
3
4
5
2
PANDORA
®
HD Movies
CinemaNow
internet radio
YouTube
6
7
8
Videos
1
9
No Disc
a Change Device
d View Devices " Enter
0
1
Selects Videos.
2
Selects Netflix.
3
Selects VUDU HD Movies.
4
Selects CinemaNow.
5
Selects Pandora® Internet Radio.
6
Selects YouTube.
7
Selects Photos.
8
Selects Music.
9
Selects Settings.
0
Displays the buttons you can use on the
remote to access functions.
✎✎ NOTE
`` The Videos, Photos, and Music options require
that you have an appropriate disc inserted into the
player or a USB flash device attached to the player.
`` The Netflix, VUDU, Cinema Now, Pandora, and
YouTube options require a working Internet
connection.
Accessing the Settings Menu
To access the Settings menu and sub-menus,
follow these steps:
1.
2.
3.
4.
5.
Press the POWER button.
The Home Menu appears.
Press the ◄► buttons to select Settings,
and then press the v button.
Press the ▲▼ buttons to select the
desired submenu, and then press the
v button.
Press the ▲▼ buttons to select the desired
item, and then press the v button.
Press the EXIT button to exit the menu.
✎✎ NOTE
`` The access steps may differ depending on
the menu you selected. The OSD (On Screen
Display) may change in this player after you
upgrade the software version.
Display Settings
You can configure various display options
such as the TV Aspect Ratio, Resolution, etc.
TV Aspect Ratio
Depending on the type of television you have,
you may want to adjust the screen size setting.
✎✎ NOTE
`` Depending on the disc type, some aspect
ratios may not be available.
`` If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
the picture might appear to be distorted.
`` If you select the 4:3 Pan-Scan or 4:3 Letter
Box, pressing the FULL SCREEN button on the
remote will not bring up a full screen picture.
`` If you select the 16:9 Original, your TV may display
4:3 Pillarbox (black bars on sides of picture). If this
occurs, pressing the FULL SCREEN button on the
remote will not bring up a full screen picture.
BD Wise (Samsung TVs only)
BD Wise is Samsung’s latest inter-connectivity feature.
When you connect a Samsung player and a Samsung TV
with BD Wise to each other via HDMI, and BD Wise is on
in both the player and TV, the player outputs video at the
video resolution and frame rate of the Blu-ray Disc/DVDs.
✎✎ NOTE
`` When BD Wise is on, the Resolution setting
automatically defaults to BD Wise and BD Wise
appears in the Resolution menu.
`` If the player is connected to a device that does not
support BD Wise, you can not use the BD Wise function.
`` For proper operation of BD Wise, set the BD
Wise menu of both the player and the TV to On.
Downloaded From DvDPlayer-Manual.com Samsung Manuals
Resolution
Lets you set the output resolution of the HDMI
video signal to Auto, 1080p, 1080i, 720p or
480p. The number indicates the number of
lines of video per frame. The i and p indicate
interlaced and progressive scan, respectively.
The more lines, the higher the quality.
Resolution according to the output
mode
• Blu-ray Disc/E-contents/Digital Contents
playback
Setup
Output
BD Wise
Auto
1080p@60F
(Movie Frame : Off)
Movie Frame :
Auto (24Fs)
1080i
720p
480p
HDMI / connected
HDMI Mode
E-contents/
Blu-ray Disc
Digital
contents
Resolution of
1080p
Blu-ray Disc
Max. Resolution Max. Resolution
of TV input
of TV input
• DVD playback
Output
Setup
BD Wise
Auto
1080p
1080i
720p
480p
1080@60F
1080@60F
1080@24F
1080p@24F
1080i
720p
480p
1080i
720p
480p
HDMI / connected
HDMI Mode
480i
Max. Resolution of TV input
1080p
1080i
720p
480p
✎✎ NOTE
`` If the TV you connected to the player does not
support Movie Frame or the resolution you
selected, the message “If no pictures are shown
after selecting ‘Yes’, please wait for 15 seconds
to return to the previous resolution. Do you
want to change the resolution?” appears. If you
select Yes, the TV’s screen will go blank for 15
seconds, and then the resolution will revert to
the previous resolution automatically.
`` If the screen stays blank after you have
changed the resolution, remove all discs,
and then press and hold the @ button on the
front of the player for more than 5 seconds.
All settings are restored to the factory default.
Follow the steps on the previous page to
access each mode and select the Display Setup
that your TV will support.
`` When the factory default settings are restored,
all stored user BD data is deleted.
`` The Blu-ray Disc must have the 24 frame feature
for the player to use the Movie Frame (24Fs) mode.
Movie Frame (24Fs)
Setting the Movie Frame (24Fs) feature to
Auto allows you to adjust the player’s HDMI
output to 24 frames per second for improved
picture quality.
You can enjoy the Movie Frame (24Fs) feature
only on a TV supporting this frame rate.
You can select Movie Frame only when the
player is in the HDMI 1080i or 1080p output
resolution modes.
HDMI Color Format
Lets you set the color space format for
HDMI output to match the capabilities of the
connected device (TV, monitor, etc).
HDMI Deep Color
Lets you output video from the HDMI OUT jack with
Deep Color. Deep Color provides more accurate
color reproduction with greater color depth.
9
Progressive Mode
Lets you improve picture quality when viewing DVDs.
Audio Settings
Digital Output
Set the Digital Output to match the capabilities of the AV receiver you’ve connected to the
player : For more details, please refer to the Digital Output Selection table below.
Digital Output Selection
Audio Stream
on Blu-ray
Disc
Bitstream
(Unprocessed)
PCM
Up to PCM 7.1ch
PCM
DTS re-encoded
Dolby Digital
PCM 2ch
Dolby Digital
DTS re-encoded
Dolby Digital Plus
PCM 2ch
Dolby Digital Plus
DTS re-encoded
Dolby TrueHD
PCM 2ch
Dolby TrueHD
DTS re-encoded
DTS
PCM 2ch
DTS
DTS re-encoded
PCM 2ch
DTS-HD Hi Resolution Audio
DTS re-encoded
PCM 2ch
DTS-HD Master Audio
DTS re-encoded
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
Dolby Digital
DTS
PCM 2ch
Dolby Digital
DTS
DTS-HD Hi
Resolution Audio
DTS-HD Master
Audio
PCM
Audio Stream
Dolby Digital
on DVD
DTS
Definition for
Blu-ray Disc
Bitstream
(Re-encoded
DTS)
PCM
Setup
Any
Decodes the main feature
audio and BONUSVIEW
audio stream together
into PCM audio and adds
Navigation Sound Effects.
Decodes the main
feature audio and
Outputs only the main feature
BONUSVIEW audio
audio stream so that your
stream together into
AV receiver can decode the
PCM audio and adds
audio bitstream.
Navigation Sound
You will not hear BONUSVIEW
Effects, then reaudio or Navigation Sound
encodes the PCM
Effects.
audio into DTS
bitstream.
Downloaded
From DvDPlayer-Manual.com Samsung Manuals
10
Bitstream
(Re-encoded
Dolby D)
Re-encoded
Dolby Digital *
Re-encoded
Dolby Digital *
Re-encoded
Dolby Digital *
Re-encoded
Dolby Digital *
Re-encoded
Dolby Digital *
Re-encoded
Dolby Digital *
Re-encoded
Dolby Digital *
PCM 2ch
Dolby Digital
DTS
Decodes the main
feature audio and
BONUSVIEW audio
stream together
into PCM audio and
adds Navigation
Sound Effects, then
re-encodes the PCM
audio into Dolby
Digital bitstream or
PCM.
* If the Source Stream is 2ch, “Re-encoded Dolby D” Setting is not applied. Output will be PCM 2ch.
Blu-ray Discs may include three audio
streams :
-- Main Feature Audio : The audio soundtrack
of the main feature.
-- BONUSVIEW audio : An additional
soundtrack such as the director or actor’s
commentary.
-- Navigation Sound Effects : When you
choose a menu navigation selection, a
Navigation Sound Effect may sound.
Navigation Sound Effects are different on
each Blu-ray Disc.
✎✎ NOTE
`` Be sure to select the correct Digital Output or
you will hear no sound or just loud noise.
`` If the HDMI device (AV receiver, TV) is not
compatible with compressed formats (Dolby
Digital, DTS), the audio signal outputs as PCM.
`` Regular DVDs do not have BONUSVIEW audio
and Navigation Sound Effects.
`` Some Blu-ray Discs do not have BONUSVIEW
audio and Navigation Sound Effects.
`` If you play MPEG audio soundtracks, the audio
signal outputs as PCM regardless of your
Digital Output selections (PCM or Bitstream).
PCM Downsampling
Lets you set 48kHz and 96kHz PCM downsampling on or off.
HDMI
• If your TV is not compatible with
compressed multi-channel formats (Dolby
Digital, DTS), the player may output PCM
2ch downmixed audio even though you
selected Bitstream (either Re-encoded or
Unprocessed) in the setup menu.
• If your TV is not compatible with PCM
sampling rates over 48kHz, the player may
output 48kHz downsampled PCM audio
even though you set PCM Downsampling
to Off.
Dynamic Range Control
You can listen at low volumes, but still hear
dialog clearly.
This is only active if your player detects a
Dolby Digital signal.
Downmixing Mode
Select the Downmix method for stereo output.
Network Settings
Please contact your ISP to find out if your IP
address is static or dynamic. If it is dynamic
- and most are - we recommend using the
Auto procedure for network setup. This is
easiest and will work in the majority of cases.
If it is static, you must use the manual set up
procedure. (See page 11.)
Network setup directions start below.
✎✎ NOTE
`` This unit can only be connected to a Network
via a wireless connection.
Automatic Network Setup
1.
2.
3.
In the Home menu, press the ◄►
buttons to select Settings, and then
press the v button.
Press the ▲▼ buttons to select Network,
and then press the v button.
Press the ▲▼ buttons to select
Network Setting, and then press the
v button. The Network Setting screen
appears.
Settings
Display
Audio
• Use the arrow keys on your remote
to move from button to button on the
Security Key screen.
Network Setting
Access Point Selection
Internet Protocol Setup
Network IP Address
System Subnet Mask
: Not Selected
: Auto
: 0
0
0
Language Gateway:
0
0
0
0
: 0
SecurityDNS
:Auto
General DNS Server
Support
: 0
0
0
0
0
0
\
• To change the kind of characters
you are entering, move to the button
labeled a/A/1/, and then press the
v button. Each time you press the
v button, you change the kind of
characters you can enter (a/A/1/).
0
0
a WPS(PBC) > Move " Select ' Return
4.
5.
6.
7.
Select Access Point Selection, and
then press the v button.
The Network function searches for
available wireless networks.
When done, it displays a list of the
available networks.
• You can also change the kind of
character by pressing the DISC
MENU button on the remote.
• To enter a letter, press the number
button that corresponds to the
letter. Pressing the button repeatedly
changes the letter.
In the list of networks, press the ▲▼
buttons to select a network, and then
press the v button.
• To enter a number or symbol when
the Security Key screen is displaying
numbers or symbols, press the
corresponding number button once.
If the Security Key screen appears, go
to Step 7. If the Network Connecting
Screen appears, go to Step 10.
• To delete the last letter, number, or
symbol you entered, move to the
Delete button, and then press the
v button.
On the Security Key screen, enter your
network’s Pass Phrase.
✎✎ NOTE
Display
Audio
Security Key
Network 1
System
Language
Security
General
Support
8.
4
7
.,@
ghi
pqrs
a/A/1/
a Clear All
Security Key
2
5
8
0
a b c
abc
jkl
tuv
b Space
(0)
3
6
9
def
mno
wxyz
Delete
c Done
(/) Cursor " Select ' Return
To enter the Pass Phrase, follow these
general directions:
11. To test the connection, press the ▼
button to select Network Test, and then
press the v button.
Manual Network Setup
If the Auto Setting does not work, you need
to enter the Network settng values manually.
Before you start manual network setup, you
need the network setting values.
To get the Network setting values, contact
your ISP or your network administrator.
To Enter the Network settings into your player,
follow these steps:
1.
2.
9.
• To clear all entered letters, numbers,
and symbols, move to the Clear
All button, and then press the v
button. You can also just press the
RED (A) button on your remote.
When done, press the YELLOW (C)
button on your remote, or move to the
Done button, and then press the v
button.
The Network Connecting screen
appears.
Downloaded From DvDPlayer-Manual.com Samsung Manuals
On the Internet Protocol Setup screen,
press the v button.
Press the ▲▼ buttons to select Manual,
and then press the v button.
Settings
• To see and use additional symbols,
press the [ or ] button when
the Security Key screen is displaying
symbols.
`` You should be able to find the Pass Phrase on
one of the set up screens you used to set up
your router or modem.
Settings
10. Wait until the connection confirmation
message is displayed, and then press
the v button. The Network Settings
screen reappears.
Display
Audio
Network Setting
Access Point Selection
Internet Protocol Setup
Network IP Address
System Subnet Mask
: Not Selected
: Manual
0
0
Language Gateway:
0
0
0
0
SecurityDNS
General DNS Server
Support
: 0
0
: 255 255 255
:Manual
: 0
0
0
\
6.
7.
8.
9.
4.
1.
2.
3.
0
5.
Use the number buttons to enter
numbers.
When done with each field, use the ► button
to move successively to the next field.
You can also use the other arrow
buttons to move up, down, and back.
Press the ▼ button to go to the first
DNS entry field. Enter the numbers as
above.
When done, press the ▲ button to return
to Access Point Selection. Select the
network, and then press the v button.
The easiest way to set up the wireless
network connection is using the WPS(PBC)
function.
If your wireless router has a WPS(PBC)
button, follow these steps:
0
Press the ▼ button to go to the first
entry field (IP Address).
Press the ▼ to go to DNS.
WPS(PBC) function
a WPS(PBC) > Move " Select ' Return
3.
Enter the IP Address, Subnet Mask,
and Gateway values.
4.
In the Network Settings menu, press the
▲▼ buttons to select Network Setting,
and then press the v button.
The Internet Protocol Setup screen
appears.
Press the RED (A) button on the remote
control.
Press the WPS(PBC) button on your
router within two minutes. Your player
displays the Network Selection Screen,
and automatically acquires all the
network setting values it needs and
connects to your network. When it is
done, it displays an OK button. Press
the v button on your remote.
After the network connection is set up,
press the RETURN button to exit the
Network Setting screen.
✎✎ NOTE
`` To comply with the revised Wi-Fi standard
specifications, WEP encryption of the wireless
router does not support WPS connections.
11
Network Test
Use this menu item to check whether your
network connection is working or not.
Network Status
Use to check whether a connection to a
network and the Internet have been established.
BD-Live Internet Connection
Set to allow or prohibit an Internet connection
when you use the BD-LIVE service.
• Allow (All) : The Internet connection is
allowed for all BD-LIVE contents.
• Allow (Valid Only) : The Internet
connection is allowed only for BD-LIVE
contents containing a valid certificate.
• Prohibit : No Internet connection is allowed
for any BD-LIVE content.
✎✎ NOTE
`` What is a valid certificate?
When the player uses BD-LIVE to send the
disc data and a request to the server to certify
the disc, the server uses the transmitted data
to check if the disc is valid and sends the
certificate back to the player.
`` The Internet connection may be restricted
while you are using BD-LIVE contents.
Using the BD-LIVE™
Once the player is connected to the network,
you can enjoy various movie-related service
contents using a BD-LIVE compliant disc.
1.
2.
3.
Insert a Blu-ray Disc that supports BDLIVE.
Select an item from various BD-LIVE
service contents provided by the disc
manufacturer.
✎✎ NOTE
`` The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
Playing content located in your
PC on the Blu-ray Disc Player
You can view shared files from your computer
on your Blu-ray Disc Player.
You can get detailed instructions for using
AllShare from the Samsung.com web site.
Blu-ray Disc Player
Using the AllShare Function
AllShare lets you play music, video, and photo
files located in your PC or NAS on the player.
To use AllShare with your player, you must
connect the player to your network (See
pages 10~12).
To use AllShare with your PC, you must install
AllShare software on your PC.
If you have NAS, you can use AllShare without
any additional software.
To download AllShare software
1.
Go to Samsung.com
3.
On the next screen, click Get downloads
under Downloads.
2.
4.
5.
Click Support, enter your player’s
product number in the field that
appears, and then click Product.
Click Software on the next page.
Click the icon in the AllShare line under
File to start the download.
Attach a USB memory stick to the USB
jack on the back of the player, and
then check its remaining memory. The
memory device must have at least 1GB
of free space to accommodate the BDLIVE services.
Downloaded
From DvDPlayer-Manual.com Samsung Manuals
12
AllShare Connection
Play back
PC’s files
System Settings
Initial Settings
By using the Initial Settings function, you can
set the language, Network Settings, etc.
For more information about the Initial Settings
function, refer to the Initial Settings section of
this user manual (page 8).
Anynet+ (HDMI-CEC)
Anynet+ is a convenient function that offers
linked operations with other Samsung players
that have the Anynet+ feature.
To operate this function, connect this player to
an Anynet+ Samsung TV with an HDMI cable.
With Anynet+ on, you can operate this player
using a Samsung TV remote control and start
disc playback simply by pressing the PLAY
) button on the TV’s remote control.
(
For more information, please see the TV user
manual.
✎✎ NOTE
`` This function is not available if the HDMI cable
does not support CEC.
`` If your Samsung TV has an Anynet+ logo, then
it supports the Anynet+ function.
`` Depending on your TV, certain HDMI output
resolutions may not work.
Please refer to the user manual of your TV.
`` After the product was turned off, disconnecting and
connecting the power cable turns it on automatically.
At the moment, it automatically turns off in about
15 seconds for re-establishing Anynet+ connection.
`` For some TV products, if connected to this
product with Anynet+ function, turning the TV on
may display a warning popup message saying no
connection was found. Still, Anynet+ connection
is properly established and available to use.
BD Data Management
Enables you to manage the downloaded
contents you accessed through a Blu-ray disc
that supports the BD-LIVE service and stored
on a flash drive.
You can check the device’s information
including the storage size, delete the BD data,
or change the Flash memory device.
✎✎ NOTE
`` In the external memory mode, disc playback
may be stopped if you disconnect the USB
device in the middle of playback.
`` Your player supports the FAT16, FAT32, and
NTFS file systems. We recommend you use
USB devices that support USB 2.0 protocol
with 4 MB/sec or faster read/write speed.
`` The Resume Play function may not work after
you format the storage device.
`` The total memory available to BD Data
Management may differ, depending on the
conditions.
Language Settings
You can select the language you prefer for the
Home menu, disc menu, etc.
✎✎ NOTE
`` The selected language will only appear if it is
supported on the disc.
Security Settings
When you access this function for the first
time, the PIN screen appears. Enter the
default PIN - 0000 - using the number
buttons. To change the PIN, use the Change
PIN function (page 13). Each time you access
the Security Settings hereafter, you must
enter that four digit PIN. If you don’t change
the PIN, continue using the default PIN.
BD Parental Rating
Prevent playback of Blu-ray Discs with specific
age ratings unless the 4 digit PIN is entered.
DVD Parental Rating
This function works in conjunction with DVDs
that have been assigned an age rating or
numeric rating that indicates the maturity level
of the content. These numbers help you control
the types of DVDs that your family can watch.
Select the rating level you want to set. For example, if you select Level 6, discs rated
above 6 - Level 7 and 8 - will not play.
A larger number indicates more mature content.
CinemaNow Lock
Netflix Lock
Restrict the use of the Netflix service unless
the 4 digit PIN is entered.
VUDU Lock
Restrict the use of the VUDU service unless
the 4 digit PIN is entered.
Pandora Lock
Restrict the use of the Pandora service unless
the 4 digit PIN is entered.
YouTube Lock
Restrict the use of the YouTube service unless
the 4 digit PIN is entered.
Change PIN
Change the 4-digit password used to access
security functions.
To change the PIN, follow these steps:
1.
2.
3.
4.
5.
Select Change PIN, and then press the
v button. The Enter old PIN screen
appears.
Enter the old PIN. If you never changed
the PIN, enter the default PIN: 0000. The Enter new PIN screen appears.
Enter the new PIN in the Enter new PIN
fields.
Re-enter the new PIN in the Confirm
new PIN fields. The “PIN is changed
successfully.” message appears.
Press the v button.
Restrict the use of the CinemaNow service
unless the 4 digit PIN is entered
Downloaded From DvDPlayer-Manual.com Samsung Manuals
If you forgot your password
1.
2.
Remove any discs.
Press and hold the @ button on the
front panel for 5 seconds or more.
All settings will revert to the factory settings.
✎✎ NOTE
4.
5.
`` The Update is complete when the player turns
off after restarting. Press the POWER button to
turn on the updated player for your use.
`` Never turn the player off or back on manually
during the update process.
General Settings
`` Samsung Electronics takes no legal
responsibility for player malfunction caused by
an unstable Internet connection or consumer
negligence during a software upgrade.
Time Zone
You can specify the time zone that is
applicable to your area.
Software Upgrade
The Software Upgrade menu allows you to
upgrade the player’s software for performance
improvements or additional services.
By Online
To upgrade By Online, follow these steps:
1.
2.
3.
Select By Online, and then press the
v button. The Connecting to Server
message appears.
A popup message will appear if an
update is available.
If you select Yes, the player will turn off
automatically before restarting.
(Never turn the player on during an
upgrade.)
Press the POWER button to turn on the
player.
✎✎ NOTE
`` When the factory default settings are restored,
all the user stored BD data will be deleted.
Support Settings
The update progress popup will appear.
When the update is completed, the
player will turn off automatically.
`` If you want to cancel the upgrade while the
upgrade software is downloading, press the
v button.
By USB
To upgrade by USB, follow these steps:
1.
Visit www.samsung.com/bluraysupport.
3.
Unzip the zip archive to your computer.
You should have a single RUF file with
the same name as the zip file.
2.
4.
5.
6.
7.
Download the latest USB software
upgrade zip archive to your computer.
Copy the RUF file to a USB flash drive.
Make sure there is no disc in the player,
and then insert the USB flash drive into
the USB port of the player.
In the player’s menu, go to Settings >
Support > Software Upgrade.
Select By USB.
13
✎✎ NOTE
`` No disc should be in the product when you
upgrade the software using the USB Host jack.
`` When the software upgrade is done, check the
software details in the software Upgrade menu.
`` Do not turn off the player during the software
upgrade. It may cause the player to malfunction.
`` Software upgrades using the USB Host jack
must be performed with a USB flash memory
stick only.
Auto Upgrade Notification
If you have connected the player to your
network, and then set Auto Upgrade
Notification on, the player automatically
notifies you when a new software version is
available for the player.
To set Auto Upgrade Notification on, follow
these steps:
1.
Select Auto Upgrade Notification, and
then press the v button.
2. Use the ▲▼ buttons to select On, and
then press the v button.
If there is a new software version available,
the player notifies you with a popup message.
1.
2.
3.
4.
✎✎ NOTE
`` The update is complete when the player turns
off after restarting. Press the POWER button to
turn on the updated player for your use.
`` Never turn the player off or on manually during
the update process.
`` Samsung Electronics takes no legal
responsibility for player malfunction caused by
an unstable Internet connection or consumer
negligence during software upgrade.
Contact Samsung
Provides contact information for assistance
with your player.
Media Play
Insert a Disc
1.
2.
3.
4.
Terms of Service Agreement
View the general disclaimer regarding third
party contents and services.
Reset
All settings will revert to the factory default
except for the network settings.
To upgrade the firmware, select Yes
in the Pop-up. The player turns off
automatically, then restarts, and begins
the download. (Never turn on the player
manually here.)
The update progress popup appears.
When the update is complete, the player
turns off again automatically.
Press the POWER button to turn on the
player.
Downloaded
From DvDPlayer-Manual.com Samsung Manuals
14
Push a disc gently into the disc tray with
the disc's label facing up.
Press the 8 button to close the disc
tray. Playback starts automatically.
If playback does not start automatically,
select the Videos option on the Main
screen, and then press the v button.
You can play multimedia files located on a
USB storage device.
2.
3.
4.
CinemaNow
internet radio
YouTube
Press the 8 button to open the disc
tray.
Insert a USB Device
1.
PANDORA
HD Movies
No Disc
123
DLNA
123 a Change Device
5.
6.
Press the ◄► buttons to select Videos,
Music or Photos, then press the v
button. Go to Step 7.
4-1. If you pressed the BLUE (D) button, the
screen below appears. Go to 5-1.
Move to the Home menu.
PANDORA
HD Movies
In Stop mode, connect the USB storage
device to the USB port on the back
panel of the player.
The message “Do you want to access
the device?” will be displayed.
Press the ◄► button to select Yes,
then press the v button.
If you have a disc in the Blu-ray player,
press the RED (A) or BLUE (D) button.
If you do not, go to Step 6.
If you pressed the RED (A) button, go to
Step 5.
If you pressed the BLUE (D) button, go
to Step 4-1.
c Safely Remove USB d View Devices " Enter
Press the ▲▼ buttons to select USB,
then press the v button.
CinemaNow
internet radio
YouTube
123
123
d Home
" Enter
5-1. Press the ◄► buttons to select USB,
then press the v button.
6-1. Press the ▲▼ buttons to select Videos,
Music or Photos, then press the v
button.
7.
The controls and tools you use to play
videos, music, and pictures located on
a USB device are identical to those you
use to play videos, music, and pictures
on a disc. (See pages 15~16)
✎✎ NOTE
`` You must remove the USB storage device
safely (by performing the “Safely Remove USB”
function) in order to prevent possible damage
to the USB memory. Press the MENU button to
move to the Home menu, select the YELLOW
(C) button, and then press the v button.
`` When Audio-CD (CD-DA), MP3 or JPEG files
are in stop mode, pressing the FULL SCREEN
button on the remote will not bring up a full
screen picture.
`` If you insert a disc when playing a USB storage
device, the device mode changes to “DVD or
CD” automatically.
Controlling Video Playback
You can control the playback of video content
located on a DVD, CD, or USB storage device.
Depending on the disc, some of the functions
described in this manual may not be available.
Buttons on the Remote Control
used for Video Playback
2
6 button
Starts playback.
7 button
Pauses playback.
5 button
Stops playback.
Fast Motion
Play
During playback, press the 3 or
4 button.
Each time you press the 3 or
4 button, the playback speed
will change.
Slow Motion
Play
In pause mode, press the 4
button.
Each time you press the 4
button, the playback speed will
change.
Step Motion
Play
In pause mode, press the 7
button.
Each time you press the 7
button, a new frame appears.
Skip Motion
Play
During playback, press the 1 or
2 button.
Each time you press 1 or 2
button, the disc moves to the
previous or next chapter or file.
wwUsing the disc menu, title menu,
popup menu, and title list
1
qqPlayback related buttons
The player does not play sound in Search,
Slow or Step mode.
• To return to normal speed playback, press
the 6 button.
DISC MENU
button
During playback, press this button
to start the disc menu function.
POPUP MENU
button
During playback, press this button
to start the popup menu function.
TITLE MENU
button
During playback, press this button
to start the title menu function.
Downloaded From DvDPlayer-Manual.com Samsung Manuals
Controlling Music Playback
You can control the playback of music
content located on a DVD, USB, or PC.
Buttons on the Remote Control
used for Music Playback
Repeat an Audio CD (CD-DA)/
MP3
1.
During Playlist playback, press the
TOOLS button.
TRACK 001
Playlist
Tools
TRACK 001
Repeat Mode
? Off
1/6
\05:57
TRACK 002
Information
< Adjust > Move ' Return04:27
TRACK 003
1
+
00:08 / 05:57
04:07
TRACK 004
03:41
TRACK 005
03:17
TRACK 006
4
2
5
6
3
1
NUMBER buttons (Audio CD (CD-DA) only) :
During Playlist playback, press the desired
track number.
The selected track is played.
2
Skip : During playback, press the 1 or 2
button to move to the previous or next file of
the playlist.
3
5 button : Stops a track.
4
5
6
2.
3.
CD
" Pause
Tools
03:35
' Return
Press the ◄► buttons to select Repeat
Mode.
Press the v button.
Off
Songs are played in the order
in which they were recorded.
(
) One Song
The current song is repeated.
(
) All
All songs are repeated.
(
)Shuffle Mode
The random option plays
songs in random order.
Fast Play (Audio CD (CD-DA) only)
During playback, press the 3 or 4
button.
Each time you press the 3 or 4 button,
the playback speed will change.
Pause : Pauses a track.
6 button : Plays the currently selected
track.
15
Playlist
1.
Playing Photo Contents
To move to the Music List, press the 5
or RETURN button.
The Music List screen appears.
Music TRACK 001
1/2 Page
TRACK 001
TRACK 001
02:38
02:38
TRACK 001
TRACK 001
02:38
02:38
02:38
02:38
TRACK 001
TRACK 001
02:38
02:38
TRACK 001
TRACK 001
02:38
02:38
2.
3.
4.
5.
CD
c Select
( ) Jump Page
' Return
Press the ▲▼◄► buttons to move
to a desired track, and then press the
YELLOW (C) button. A check appears
on the track.
Repeat this procedure to select
additional tracks.
To remove a track from the list, move to
the track, and then press the YELLOW
(C) button again.
The check on the track is cancelled.
When done, press the v button.
To go to the Music List, press the
RETURN button.
✎✎ NOTE
Using the Tools Menu
During playback, press the TOOLS button.
Slide Show
Select to start the slide show.
Zoom
Select to enlarge the current
picture. (Enlarge up to 4 times)
Rotate
Select to rotate the picture. (This
will rotate the picture either
clockwise or counter clockwise.)
Background
Music
TRACK 001
TRACK 001
You can play photo contents located on a
DVD, CD, or a USB storage device.
`` You can create a playlist with up to 99 tracks
on Audio CDs (CD-DA).
Information
✎✎ NOTE
Select to listen to music while
viewing a slide show.
Shows the picture information.
`` Depending on the disc or storage device, the
Tools menu may differ.
`` To enable the background music function, the
photo file must be in the same storage media
as the music file.
However, the sound quality can be affected
by the bit rate of the MP3 file, the size of the
photo, and the encoding method.
`` You can't enlarge the subtitle and PG graphic
in the full screen mode.
Downloaded
From DvDPlayer-Manual.com Samsung Manuals
16
Appendix
Troubleshooting
Before requesting service, please try the following solutions.
PROBLEM
SOLUTION
No operation can be
performed with the remote
control.
• Check the batteries in the remote control. They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several minutes
to drain the microprocessor inside the remote control to reset it. Reinstall
batteries and try to operate the remote control again.
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the Blu-ray Disc/DVD.
Disc Menu does not appear.
• Ensure that the disc has disc menus.
The prohibition message
appears on the screen.
• This message appears when an invalid button is pressed.
• The Blu-ray Disc/DVD’s software doesn’t support the feature (e.g., angles).
• You’ve requested a title or chapter number or search time that is out of range.
Play mode differs from the
Setup Menu selection.
• Some of the functions selected in the Setup Menu may not work properly if
the disc is not encoded with the corresponding function.
The screen ratio cannot be
changed.
• The Screen Ratio is fixed on your Blu-ray Disc/DVD.
• This is not a problem with the player.
No audio.
• Make sure you have selected the correct Digital Output in the Audio Options
Menu.
The screen is blank.
• If the HDMI output is set to a resolution your TV cannot support (for example,
1080p), you may not see a picture on your TV.
• Press the @ button (on front panel) for more than 5 seconds with no disc
inside. All settings will revert to the factory settings.
• When the factory default settings are restored, all stored user BD data is
deleted.
PROBLEM
SOLUTION
PROBLEM
SOLUTION
Forgot password
• Press the @ button (on front panel) for more than 5 seconds with no disc
inside. All settings including the password will revert to the factory settings.
Don’t use this unless absolutely necessary.
• When the factory default settings are restored, all stored user BD data is
deleted.
I cannot connect to the BDLIVE server.
If you experience other
problems.
• Go to the contents and find the section of the user manual that contains the
explanations regarding the current problem, and follow the procedure once
again.
• If the problem still cannot be solved, please contact your nearest Samsung
authorized service center.
• Check whether the network connection is working or not by using the
Network Status menu.
• Check whether the USB memory device is connected to the player.
• The memory device must have at least 1GB of free space to accommodate
the BD-LIVE service.
You can check the available size in BD Data Management.
• Check whether the BD-LIVE Internet Connection menu is set to Allow(All).
• If all above fails, contact the contents provider or update the player to the
latest firmware.
The picture is noisy or
distorted
• Make sure that the disc is not dirty or scratched.
• Clean the disc.
When using the BD-LIVE
service, an error occurs.
• The memory device must have at least 1GB of free space to accommodate
the BD-LIVE service.
You can check the available size in BD Data Management.
No HDMI output.
• Check the connection between the TV and the HDMI jack of the player.
• Check if your TV supports 480p, 720p, 1080i, or 1080p HDMI input
resolutions.
Abnormal HDMI output
screen.
• If random noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
AllShare function
I can see folders shared
• AllShares shows only files corresponding to the Image, Music, and Movie
through AllShare, but I cannot
categories. Files that do not correspond to these categories are not displayed.
see the files.
Video is played intermittently.
• Check if the network is stable.
• Check if the network cable is properly connected and if the network is not
overloaded.
AllShare connection between
Player and PC is unstable.
• The IP address under the same subnetwork should be unique. If they are not,
IP interference can cause this phenomenon.
• Check if you have a firewall enabled.
If so, disable the firewall function.
Downloaded From DvDPlayer-Manual.com Samsung Manuals
BD-LIVE
✎✎ NOTE
`` When the factory default settings are restored, all stored user BD data is deleted.
Repairs
If you contact us to repair your player, an administration fee may be charged if either:
1.
2.
An engineer is called out to your home at your request and there is no defect in the
product.
You bring the unit to a repair center and there is no defect in the product.
We will provide you with the amount of the administration fee before we make a home visit or
begin any work on your player.
We recommend you read this manually thoroughly, search for a solution on line at www.
samsung.com, or contact Samsung Customer Care at 1-800-SAMSUNG (726-7864) before
seeking to repair your player.
17
Specifications
Power Requirements
AC 120V, 60Hz
Weight
2.2 Ibs
Power Consumption
General
Dimensions
Operating Temperature Range
Operating Humidity Range
USB
HDMI
Network
-----
Type A
10.5W
10.6 (W) X 7.6 (D) X 1.6 (H) inches
+41°F to +95°F
10 % to 75 %
USB 2.0
DC output
5V 500mA Max.
Audio
PCM, Bitstream
Video
Wireless LAN
1080p, 1080i, 720p, 480p
Bulit-in
Network speeds equal to or below 10Mbps are not supported.
Design and specifications are subject to change without prior notice.
Weight and dimensions are approximate.
Dispose unwanted electronics through an approved recycler.
To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect
or call, (877) 278 - 0799
Downloaded
From DvDPlayer-Manual.com Samsung Manuals
18
Compliance and Compatibility Notice
NOT ALL discs are compatible
• Subject to the restrictions described below and those noted throughout this Manual,
including the Disc Type and Characteristics section of this user manual, disc types that can
be played are: pre-recorded commercial BD-ROM, DVD-VIDEO, and Audio CD (CD-DA)
discs; BD-RE/-R, DVD-RW/-R discs; and CD-RW/-R discs.
• Discs other than those listed above cannot be and are not intended to be played by this
player. Some of the discs listed above may not play due to one or more reasons provided
below.
• Samsung cannot assure that this player will play every disc bearing the BD-ROM, BD-RE/-R,
DVD-VIDEO, DVD-RW/-R, DVD+RW/+R and CD-RW/-R logos, and this player may not
respond to all operating commands or operate all features of every disc. These and other
disc compatibility and player operation issues with new and existing format discs are
possible because:
-- Blu-ray is a new and evolving format and this player may not operate all features of Bluray Discs because some features may be optional, additional features may have been
added to the Blu-ray Disc format after the production of this player, and certain available
features may be subject to delayed availability;
-- not all new and existing disc format versions are supported by this player;
-- new and existing disc formats may be revised, changed, updated, improved and/or
supplemented;
-- some discs are produced in a manner that allows specific or limited operation or restricts
features during playback;
-- some discs bearing the BD-ROM, BD-RE/-R, DVD-VIDEO, DVD-RW/-R, DVD+RW/+R
and CD-RW/-R logos may still be non-standardized discs;
-- some discs may not be played depending on their physical state or recording conditions;
-- problems and errors can occur during the creation of Blu-ray Disc or DVD software and/or
the manufacture of discs;
-- this player operates differently than a standard DVD player or other AV equipment; and/or
-- for reasons noted throughout this user manual and for other reason(s) discovered and
posted by SAMSUNG customer care center.
• If you encounter disc compatibility or player operation problems, please contact SAMSUNG
customer care center.
You may also contact SAMSUNG customer care center for possible updates on this player.
• For additional information on playback restrictions and disc compatibility, refer to the
Precautions, Before Reading the user manual, Disc Types and Characteristics, and Before
Playing sections of this user manual.
• For Blu-ray Disc Player progressive scan output : CONSUMERS SHOULD NOTE THAT
NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS
product AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF
PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE
QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS product, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.
Copy Protection
• Because AACS (Advanced Access Content System) is approved as the content protection
system for the Blu-ray Disc format, similar to use of CSS (Content Scramble System) for
the DVD format, certain restrictions are imposed on playback, analog signal output, etc., of
AACS protected contents.
The operation of this product and restrictions on this product may vary depending on your
time of purchase as those restrictions may be adopted and/or changed by AACS after the
production of this product. Furthermore, BD-ROM Mark and BD+ are additionally used as
content protection systems for the Blu-ray Disc format, which imposes certain restrictions
including playback restrictions for BD-ROM Mark and/or BD+ protected contents. To obtain
additional information on AACS, BD-ROM Mark, BD+, or this product, please contact
SAMSUNG customer care center.
• Many Blu-ray Disc/DVDs are encoded with copy protection. Because of this, you should
only connect your Player directly to your TV, not to a VCR. Connecting to a VCR results in a
distorted picture from copy-protected Blu-ray Disc/DVDs.
• Under the U.S. Copyright laws and Copyright laws of other countries, unauthorized
recording, use, display, distribution, or revision of television programs, videotapes, Blu-ray
Discs, DVDs, and other materials may subject you to civil and/or criminal liability.
• Cinavia Notice : This product uses Cinavia technology to limit the use of unauthorized
copies of some commercially-produced film and videos and their soundtracks. When
a prohibitet use of an unauthorized copy is detected, a message will be displayed and
playback or copying will be interrupted. More information about Cinavia technology is
provided at the Cinavia Online Consumer Information Center at http://www.cinavia.com.
To request additional information about Cinavia by email, send a postcard with your mailing
address to: Cinavia Consumer Information Center, P.O. Box 86851, San Diego CA, 92138,
USA.
This product incorporates proprietary technology under licence from Verance Corporation
and is protected by U.S. Patent 7,369,677 and other U.S. and worldwide patens issued
and pending as well as copyright and trade secret protection for certain aspects of such
technology. Cinavia is a trademark of Verance Corporation. Copyright 2004-2010 Verance
Corporation. All right reserved by Verance. Reverse engineering or disassembly is prohibited.
Downloaded From DvDPlayer-Manual.com Samsung Manuals
Network Service Disclaimer
All content and services accessible through this device belong to third parties and are
protected by copyright, patent, trademark and/or other intellectual property laws. Such
content and services are provided solely for your personal noncommercial use. You may not
use any content or services in a manner that has not been authorized by the content owner or
service provider. Without limiting the foregoing, unless expressly authorized by the applicable
content owner or service provider, you may not modify, copy, republish, upload, post, transmit,
translate, sell, create derivative works, exploit, or distribute in any manner or medium any
content or services displayed through this device.
THIRD PARTY CONTENT AND SERVICES ARE PROVIDED “AS IS.” SAMSUNG DOES NOT
WARRANT CONTENT OR SERVICES SO PROVIDED, EITHER EXPRESSLY OR IMPLIEDLY,
FOR ANY PURPOSE. SAMSUNG EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. SAMSUNG DOES NOT GUARANTEE THE ACCURACY, VALIDITY,
TIMELINESS, LEGALITY, OR COMPLETENESS OF ANY CONTENT OR SERVICE MADE
AVAILABLE THROUGH THIS DEVICE AND UNDER NO CIRCUMSTANCES, INCLUDING
NEGLIGENCE, SHALL SAMSUNG BE LIABLE, WHETHER IN CONTRACT OR TORT,
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES,
ATTORNEY FEES, EXPENSES, OR ANY OTHER DAMAGES ARISING OUT OF, OR IN
CONNECTION WITH, ANY INFORMATION CONTAINED IN, OR AS A RESULT OF THE USE
OF ANY CONTENT OR SERVICE BY YOU OR ANY THIRD PARTY, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Third party services may be terminated or interrupted at any time, and Samsung makes no
representation or warranty that any content or service will remain available for any period
of time. Content and services are transmitted by third parties by means of networks and
transmission facilities over which Samsung has no control. Without limiting the generality of
this disclaimer, Samsung expressly disclaims any responsibility or liability for any interruption or
suspension of any content or service made available through this device.
Samsung is neither responsible nor liable for customer service related to the content and
services. Any question or request for service relating to the content or services should be made
directly to the respective content and service providers.
19
License
• Manufactured under license from Dolby Laboratories. Dolby and the
double-D symbol are trademarks of Dolby Laboratories.
• Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380;
6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the
Symbol & DTS and the Symbol together are registered trademarks & DTS
2.0+Digital Out is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights
2.0+Digital Out
Reserved.
• The terms HDMI and HDMI High-Definition Multimedia Interface, and
the HDMI Logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
• Oracle and Java are registered trademarks of Oracle and/or its affiliates.
Other names may be trademarks of their respective owners
• Open Source License Notice
-- In the case of using open source software, Open Source Licenses are available on the
product menu.
• Blu-ray Disc™, Blu-ray™ and the logos are trademarks of the Blu-ray Disc Association.
Downloaded
From DvDPlayer-Manual.com Samsung Manuals
20
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and
distributed by SAMSUNG and delivered new, in the
original carton to the original consumer purchaser,
is warranted by SAMSUNG against manufacturing
defects in materials and workmanship for a limited
warranty period of:
One (1) Year Parts and Labor*
(*90 Days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of
purchase, and is valid only on products purchased and
used in the United States. To receive warranty service,
the purchaser must contact SAMSUNG for problem
determination and service procedures. Warranty
service can only be performed by a SAMSUNG
authorized service center. The original dated bill of sale
must be presented upon request as proof of purchase
to SAMSUNG or SAMSUNG's authorized service
center. Transportation of the product to and from the
service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at
our option and at no charge as stipulated herein,
with new or reconditioned parts or products if
found to be defective during the limited warranty
period specified above. All replaced parts and
products become the property of SAMSUNG and
must be returned to SAMSUNG. Replacement
parts and products assume the remaining original
warranty, or ninety (90) days, whichever is longer.
SAMSUNG’s obligations with respect to software
products distributed by SAMSUNG under the SAMSUNG
brand name are set forth in the applicable end user
license agreement. Non-SAMSUNG hardware and
software products, if provided, are on an “AS IS” basis.
Non-SAMSUNG manufacturers, suppliers, publishers,
and service providers may provide their own warranties.
This limited warranty covers manufacturing defects
in materials and workmanship encountered in
normal, and except to the extent otherwise expressly
provided for in this statement, noncommercial use
of this product, and shall not apply to the following,
including, but not limited to: damage which occurs in
shipment; delivery and installation; applications and
uses for which this product was not intended; altered
product or serial numbers; cosmetic damage or
exterior finish; accidents, abuse, neglect, fire, water,
lightning or other acts of nature; use of products,
equipment, systems, utilities, services, parts,
supplies, accessories, applications, installations,
repairs, external wiring or connectors not supplied
and authorized by SAMSUNG, or which damage
this product or result in service problems; incorrect
electrical line voltage, fluctuations and surges;
customer adjustments and failure to follow operating
instructions, cleaning, maintenance and environmental
instructions that are covered and prescribed in the
instruction book; product removal or reinstallation;
reception problems and distortion related to noise,
echo, interference or other signal transmission and
delivery problems. SAMSUNG does not warrant
uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER
THAN THOSE LISTED AND DESCRIBED ABOVE, AND
NO WARRANTIES WHETHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER
THE EXPRESS WARRANTY PERIODS STATED ABOVE,
AND NO OTHER EXPRESS WARRANTY OR GUARANTY
GIVEN BY ANY PERSON, FIRM OR CORPORATION
WITH RESPECT TO THIS PRODUCT SHALL BE BINDING
ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE
FOR LOSS OF REVENUE OR PROFITS, FAILURE TO
REALIZE SAVINGS OR OTHER BENEFITS, OR ANY
OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT, REGARDLESS OF THE LEGAL
THEORY ON WHICH THE CLAIM IS BASED, AND EVEN
IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY
KIND AGAINST SAMSUNG BE GREATER IN AMOUNT
THAN THE PURCHASE PRICE OF THE PRODUCT SOLD
BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE.
WITHOUT LIMITING THE FOREGOING, PURCHASER
ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE
OR INJURY TO PURCHASER AND PURCHASER’S
PROPERTY AND TO OTHERS AND THEIR PROPERTY
ARISING OUT OF THE USE, MISUSE OR INABILITY TO
USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED
DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS
LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE
OTHER THAN THE ORIGINAL PURCHASER OF THIS
PRODUCT, IS NONTRANSFERABLE AND STATES YOUR
EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an
implied warranty lasts, or the exclusion or limitation of
incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This
warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
To obtain warranty service, please contact
SAMSUNG customer care center.
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
IN THE US
1-800-SAMSUNG
(726-7864)
www.samsung.com
WRITE
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park,
NJ 07660-2112
AK68-02273A-01
Downloaded From DvDPlayer-Manual.com Samsung Manuals
AK68-02273A-00