STC-GE33A / GEC33A
STC-GE83A / GEC83A
STC-GE152A / GEC152A
STC-GE202A / GEC202A
Product Specification
GigE Vision
Color / Monochrome CCD Camera Series
STC-GE Series
Safety Precautions
CAUTION
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
OPEN SHOCK
RISK DO
OF NOT
ELECTRIC
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT OPEN
For U.S.A.
For U.S.A.
For U.S.A.
Warning:
Warning:
Warning:
This equipment generates and uses radio frequency energy and if
This
equipment
generates
and uses
radio
frequency
energy
and
not
installed
and used
properly,
I.e.,
strict
accordance
with
the ifand if
This equipment
generates
andin
uses
radio
frequency
energy
not installed
and used
I.e., inI.e.,
strict
accordance
with the
instruction
manual,
mayproperly,
causeproperly,
harmful
interference
to radio
not installed
and
used
in strict
accordance
with the
instruction
manual,
maybeen
cause
harmful
interference
to radio
communications.
It has
tested
and
found
to comply
with
the
instruction
manual,
may
cause
harmful
interference
to radio
communications.
It
has
been
tested
and
found
to
comply
with
the
communications.
It has been
and found
to comply
with the
limits for
a Class A computing
devicetested
pursuant
to Subpart
J of Part
for a Class
A computing
devicedevice
to Subpart
J of Part
limits
for a which
Class
A
pursuant
to Subpart
J of Part
15limits
of FCC
Rules,
arecomputing
designed
topursuant
provide
reasonable
15 of 15
FCC
Rules,
which
are
designed
to
provide
reasonable
FCC Rules,
which are designed
to provide
protectionof
against
such interference
when operated
in a reasonable
commercial
protection
against
such interference
when when
operated
in a commercial
protection
against
such interference
operated
in a commercial
environment.
environment.
environment.
!! !
CAUTION:
CAUTION:
CAUTION:
TO REDUCE
THE RISK OF ELECTRIC SHOCK, DO NOT
TO REDUCE
THE(OR
RISK
OF ELECTRIC
SHOCK,
DO NOT
REMOVE
COVER
BACK).
SERVICEABLE
TO
REDUCE
THE
RISKNO
OF USER
ELECTRIC
SHOCK, DO NOT
REMOVE
COVER (OR BACK). NO USER SERVICEABLE
PARTS
INSIDE.
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE.
PARTS INSIDE.
REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
For
ForCanada
Canada
For Canada
Warning:
Warning:
Warning:
This
apparatus
does
exceed the
AAlimits
for
Thisdigital
digital
apparatus
doesnot
not
theClass
Class
limits
forradio
radio
This digital
apparatus
doesexceed
not exceed
the Class
A limits
for radio
noise
from
apparatus
set
ininthe
noiseemissions
emissions
fromdigital
digital
apparatus
setout
outset
theRadio
Radio
noise
emissions
from digital
apparatus
out
in
the Radio
Interference
Regulations
of
the
Canadian
Department
of
Interference
Regulations
of theof
Canadian
Department
of of
Interference
Regulations
the Canadian
Department
Communications.
Communications.
Communications.
The
flash
arrowhead
Thelightning
lightning
flashwith
with
The lightning
flasharrowhead
with arrowhead
symbol,
within
ananequilateral
triangle,
symbol,
withinwithin
equilateral
triangle,
symbol,
an equilateral
triangle,
isisintended
totoalert
the
user
totothe
intended
alert
the
user
theto the
is intended to alert the user
presence
ofofuninsulated
“dangerous
presence
uninsulated
“dangerous
presence
of uninsulated
“dangerous
voltage”
within
the
voltage”
withinwithin
theproduct’s
product’s
voltage”
the product’s
enclosure
that
may
be
of
sufficient
enclosure
that
may
be
of
sufficient
enclosure that may be of sufficient
magnitude
totoconstitute
a arisk
magnitude
constitute
riskof
magnitude
to constitute
aofrisk of
electric
shockto
topersons.
persons.
electric
shock
electric
shock
to persons.
!!
Theexclamation
exclamation
pointwithin
withinwithin
The
point
anan an
The exclamation
point
equilateral
triangle
intended
alert
equilateral
triangle
isisintended
totoalert
equilateral
triangle
is intended
to alert
theuser
user
thepresence
presence
important
the
totouser
the
ofofimportant
the
to
the presence
of important
operating
andmaintenance
maintenance
(servicing)
operating
and
(servicing)
operating
and maintenance
(servicing)
instructions
theliterature
literature
instructions
in
the literature
instructions
ininthe
accompanying
the
appliance.
accompanying
the appliance.
accompanying
the appliance.
WARNING:
WARNING:
WARNING:
TOPREVENT
PREVENT
FIREOR
ORSHOCK
SHOCK
HAZARD,
DONOT
NOT
EXPOSE
TO
FIRE
HAZARD,
DO
TO PREVENT
FIRE
OR SHOCK
HAZARD,
DOEXPOSE
NOT
EXPOSE
THISAPPLIANCE
APPLIANCE
TORAIN
RAIN
ORMOISTURE.
MOISTURE.
THIS
TO
THIS
APPLIANCE
TO OR
RAIN
OR MOISTURE.
Product Precautions








Handle the camera with care. Do not abuse the camera; avoid striking or shaking it. Improper handling
or storage could damage the camera.
Do not pull or damage the camera cable.
During camera use, do not wrap he unit in any material. This will cause the internal temperature of the
unit to increase.
Do not expose the camera to moisture, or do not try to operate it in wet areas.
Do not operate the camera beyond its temperature, humidity and power source ratings.
While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or
contamination from getting in the CCD or filter area and scratching or damaging this area.
Do not keep the camera under the following conditions:
 In wet, moist, and high humidity areas
 Under hot, direct sunlight
 In high temperature areas
 Near an object that releases a strong magnetic or electric field
 Areas with strong vibrations
Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO not
scratch the surface of the glass.
Product Specifications
2
Rev 3.01
STC-GE Series
Copyright & Disclaimer
Sensor Technologies America, Inc. (DBA Sentech America) believes the contents and specifications of its website, catalog,
documentation and ads are correct; however, Sentech America provides no representation or warranty regarding such information or
product(s) contained therein. It is requested that Sentech America be given appropriate acknowledgement in any subsequent use of
such work by a third party.
While every effort has been made to ensure that the details contained in Sentech America’s website and all documentation are correct
and up-to-date, Sentech America assumes no liability, legal or otherwise for any errors in listings, specifications, part numbers,
process, software or model applications. Sentech America reserves the right to change specifications, product descriptions, product
quality, pricing and application at any time without prior written or oral notice. Any party using such information assumes all risk for
any and all damaged caused to themselves, a third party and/or property by virtue of incorrect information and/or failure of these
products. By installing and/or using a Sentech America software development kit or other similar product and/or information obtained
from Sentech America’s website, catalog, documentation or ads, you hereby accept and understand these stated terms and conditions.
Product Specifications
3
Rev 3.01
STC-GE Series
Contents
I. Specifications ..................................................................................................................................................... 5-16
A. Electronic Specifications / Mechanical Specifications / Environmental Specifications ............................................. 5-14
1. STC-GE33A / STC-GEC33A ........................................................................................................................................ 5-7
2. STC-GE83A / STC-GEC83A ...................................................................................................................................... 8-10
4. STC-GE152A / STC-GEC152A ................................................................................................................................ 11-13
5. STC-GE202A / STC-GEC202A ................................................................................................................................ 14-16
B. Connector Specifications ......................................................................................................................................... 17-18
1. RJ45 Connector ......................................................................................................................................................... 17
2. Power/IO Connector ............................................................................................................................................ 18-19
3. DC IRIS Lens Connector ............................................................................................................................................. 19
II. I/O Circuits........................................................................................................................................................... 20
III. Dimensions ......................................................................................................................................................... 21
Product Specifications
4
Rev 3.01
STC-GE Series
I. Specifications
A. Electronic Specifications / Mechanical Specifications / Environmental Conditions
1. STC-GE33A / STC-GEC33A
Product
Electronic
Specifications
STC-GEC33A
1/3” Interline VGA color
progressive CCD: ICX424AQ
Imager
Total Picture Elements
Active Picture Elements
Chip Size
Cell Size
Scanning System
Vertical Frequency (Frame Rate)
Horizontal Frequency
Pixel Frequency
@ 8bit output
Noise Level
@ 10bit output
@ 12bit output
Minimum Scene Illumination
Sync. System
Video Output
Interface
Protocol
Exposure Time
ALC
Gain
Gamma
AOI Function
Smear Reduction
Color Interpolation
White Balance Function
Trigger Mode
Communication
I/Os
Auto IRIS lens control
Power
Product Specifications
Input Voltage
Consumption
STC-GE33A
1/3” Interline VGA monochrome
progressive CCD: ICX424AL
692 (H) x 504 (V)
VGA: 648 (H) x 494 (V)
5.79 (H) x 4.89 (V) mm
7.4 (H) x 7.4 (V) µm
Progressive
89.91172 Hz at full resolution
0.72028 to 360.33325 Hz adjustable via the communication
Maximum frame rate depends on the AOI setting
Maximum frame rate of the camera(360.33325) is 104 vertical resolution AOI setting
47.2028 kHz
36.8181 MHz
≤ 3 Digit (Gain 0 dB)
≤ 12 Digit (Gain 0 dB)
≤ 48 Digit (Gain 0 dB)
25.75 Lux at F1.2, 89.91172 Hz
0.58 Lux at F1.2, 89.91172 Hz
Internal
Digital 8, 10 or 12 bit Raw Data
or
Digital 8, 10 or 12 bit Raw Data
RGB 8 bit
IEEE802.3 (1000BASE-T)
GigE Vision® 1.2 and GenICam™ 2.0 compliant
Preset continuous mode: 10 useconds to 16,777,216 useconds
Preset trigger mode: 10 useconds to 16,777,216 useconds
Pulse width mode: 10 useconds to Unlimited
Auto iris lens, electronic iris and AGC (ON/OFF)
0 to 20.4 dB
Gamma 1.0 (Factory default) or uploadable gamma table
Programmable AOI setting via the communication
Selectable ON/OFF via the communication
Available on RGB output
N/A
Auto, manual and push-to-set white balance
is available on both Raw data output
N/A
and RGB output
Edge preset trigger, Pulse width trigger (unlimited long exposure)
UART communication through Ethernet port
One opto-isolated input and two LVTTL outputs
DC IRIS control input with video level target, peak/average and zone weight settings
via the communication
+10.8 to +26.4 Vdc
Less than 5.0 W
5
Rev 3.01
STC-GE Series
Product
Mechanical
Specifications
Dimensions
Optical Filter
Optical Center Accuracy
Material
Lens Mount
Connectors
Camera Mount Screws
Weight
Environmental
Specifications
Operational
Temperature
Minimum
Maximum
Storage Temperature
Vibration
Shock
Standard Compliancy
RoHS
STC-GEC33A
STC-GE33A
35 (W) x 35 (H) x 50.6 (D) mm excluding connectors
IR cut filter on
No filter
Positional accuracy in H and V directions: +/- 0.3 mm
Rotational accuracy of H and V: +/- 1.5 deg.
Aluminum (AC)
C mount
RJ45 connector
Power/IO connector: HR10A-7R-6PB (Hirose) or equivalent
DC IRIS lens connector: M1951 (EMUDEN) or equivalent
Two 1/4” Tripod screw holes: (One on each top and bottom plate),
Twelve M4 screws holes: (Four on each top and bottom plate, two on each side plate)
Approximately 120 g
Environmental Temperature -5⁰C
Camera housing temperature (top plate) shall not exceed 65⁰C
(This corresponds to an environmental temperature of approximately 35⁰C)
Environmental Temperature -30⁰C to 65⁰C
20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each
Acceleration 38G, half amplitude 6ms, 3 directions 3 times each
EMS: EN61000-6-2, EMI: EN55011
RoHS Compliant
Note: Please use this camera in surrounding temperature conditions that are less than 35⁰C or in conditions where the
camera’s top case plate is less than 65⁰C.
When the camera is used in surrounding temperatures that exceed 35⁰C, please make sure that the camera is set
up to properly radiate heat (maintaining the camera’s top case plate’s temperature to be less than 65⁰C).
Taking these steps will maintain the heat rating of the electronic components of the camera.
Product Specifications
6
Rev 3.01
STC-GE Series
Spectral Sensitivity Characteristics
STC-GE33A
1
Relative Response
0.8
0.6
0.4
0.2
0
400
500
600
700
Wave length [nm]
800
900
1000
STC-GEC33A (with IR cut filter)
1
G
R
0.8
Relative Response
B
0.6
IR cut filter
0.4
0.2
0
400
500
600
700
Wave length [nm]
Product Specifications
7
Rev 3.01
STC-GE Series
2. STC-GE83A / STC-GEC83A
Product
Electronic
Specifications
STC-GEC83A
1/3” Interline XGA color
progressive CCD: ICX204AK
Imager
Total Picture Elements
Active Picture Elements
Chip Size
Cell Size
Scanning System
Vertical Frequency (Frame Rate)
Horizontal Frequency
Pixel Frequency
@ 8bit output
Noise Level
@ 10bit output
@ 12bit output
Minimum Scene Illumination
Sync. System
Video Output
Interface
Protocol
Shutter Speed
ALC
Gain
Gamma
AOI Function
Smear Reduction
Color Interpolation
White Balance Function
Trigger Mode
Communication
I/Os
Auto IRIS lens control
Power
Product Specifications
Input Voltage
Consumption
STC-GE83A
1/3” Interline XGA monochrome
progressive CCD: ICX204AL
1077 (H) x 788 (V)
XGA: 1024 (H) x 768 (V)
5.5 (H) x 4.92 (V) mm
4.65 (H) x 4.65 (V) µm
Progressive
36.42113 Hz at full resolution
0.44238 to 150.21358 Hz adjustable via the communication
Maximum frame rate depends on the AOI setting
Maximum frame rate of the camera(150.21358) is 146 vertical resolution AOI setting
28.9907 kHz
36.818175 MHz
≤ 3 Digit (Gain 0 dB)
≤ 12 Digit (Gain 0 dB)
≤ 48 Digit (Gain 0 dB)
24.70 Lux at F1.2, 36.42113 Hz
0.95 Lux at F1.2, 36.42113 Hz
Internal
Digital 8, 10 or 12 bit Raw Data
or
Digital 8, 10 or 12 bit Raw Data
RGB 8 bit
IEEE802.3 (1000BASE-T)
GigE Vision® 1.2 and GenICam™ 2.0 compliant
Preset continuous mode: 10 useconds to 16,777,216 useconds
Preset trigger mode: 10 useconds to 16,777,216 useconds
Pulse width mode: 10 useconds to Unlimited
Auto iris lens, electronic iris and AGC (ON/OFF)
0 to 20.4 dB
Gamma 1.0 (Factory default) or uploadable gamma table
Programmable AOI setting via the communication
Selectable ON/OFF via the communication
Available on RGB output
N/A
Auto, manual and push-to-set white balance
is available on both Raw data output
N/A
and RGB output
Edge preset trigger, Pulse width trigger (unlimited long exposure)
UART communication through Ethernet port
One opto-isolated input and two LVTTL outputs
DC IRIS control input with video level target, peak/average and zone weight settings
via the communication
+10.8 to +26.4 Vdc
Less than 5.0 W
8
Rev 3.01
STC-GE Series
Product
Mechanical
Specifications
Dimensions
Optical Filter
Optical Center Accuracy
Material
Lens Mount
Connectors
Camera Mount Screws
Weight
Environmental
Specifications
Operational
Temperature
Minimum
Maximum
Storage Temperature
Vibration
Shock
Standard Compliancy
RoHS
STC-GEC83A
STC-GE83A
35 (W) x 35 (H) x 50.6 (D) mm excluding connectors
IR cut filter on
No filter
Positional accuracy in H and V directions: +/- 0.3 mm
Rotational accuracy of H and V: +/- 1.5 deg.
Aluminum (AC)
C mount
RJ45 connector
Power/IO connector: HR10A-7R-6PB (Hirose) or equivalent
DC IRIS lens connector: M1951 (EMUDEN) or equivalent
Two 1/4” Tripod screw holes: (One on each top and bottom plate),
Twelve M4 screws holes: (Four on each top and bottom plate, two on each side plate)
Approximately 120 g
Environmental Temperature -5⁰C
Camera housing temperature (top plate) shall not exceed 65⁰C
(This corresponds to an environmental temperature of approximately 35⁰C)
-30⁰C to 65⁰C
20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each
Acceleration 38G, half amplitude 6ms, 3 directions 3 times each
EMS: EN61000-6-2, EMI: EN55011
RoHS Compliant
Note: Please use this camera in surrounding temperature conditions that are less than 35⁰C or in conditions where the
camera’s top case plate is less than 65⁰C.
When the camera is used in surrounding temperatures that exceed 35⁰C, please make sure that the camera is set
up to properly radiate heat (maintaining the camera’s top case plate’s temperature to be less than 65⁰C).
Taking these steps will maintain the heat rating of the electronic components of the camera.
Product Specifications
9
Rev 3.01
STC-GE Series
Spectral Sensitivity Characteristics
STC-GE83A
1
Relative Response
0.8
0.6
0.4
0.2
0
400
500
600
700
Wave length [nm]
800
900
1000
STC-GEC83A (with IR cut filter)
1
G
Relative Response
0.8
R
B
0.6
IR cut filter
0.4
0.2
0
400
500
600
700
Wave length [nm]
Product Specifications
10
Rev 3.01
STC-GE Series
3. STC-GE152A / STC-GEC152A
Product
Electronic
Specifications
STC-GEC152A
1/2” Interline SXGA color
progressive CCD: ICX205AK
Imager
Total Picture Elements
Active Picture Elements
Chip Size
Cell Size
Scanning System
Vertical Frequency (Frame Rate)
Horizontal Frequency
Pixel Frequency
@ 8bit output
Noise Level
@ 10bit output
@ 12bit output
Minimum Scene Illumination
Sync. System
Video Output
Interface
Protocol
Shutter Speed
ALC
Gain
Gamma
AOI Function
Smear Reduction
Color Interpolation
White Balance Function
Trigger Mode
Communication
I/Os
Auto IRIS lens control
Power
Product Specifications
Input Voltage
Consumption
STC-GE152A
1/2” Interline SXGA monochrome
progressive CCD: ICX205AL
1434 (H) x 1050 (V)
SXGA: 1360 (H) x 1040 (V)
7.6 (H) x 6.2 (V) mm
4.65 (H) x 4.65 (V) µm
Progressive
19.25954 Hz at full resolution
0.31387 to 77.03817 Hz adjustable via the communication
Maximum frame rate depends on the AOI setting
Maximum frame rate of the camera(77.03817) is 200 vertical resolution AOI setting
20.5688 kHz
36.818175 MHz
≤ 3 Digit (Gain 0 dB)
≤ 12 Digit (Gain 0 dB)
≤ 48 Digit (Gain 0 dB)
15.49 Lux at F1.2, 19.25954 Hz
0.41 Lux at F1.2, 19.25954 Hz
Internal
Digital 8, 10 or 12 bit Raw Data
or
Digital 8, 10 or 12 bit Raw Data
RGB 8 bit
IEEE802.3 (1000BASE-T)
GigE Vision® 1.2 and GenICam™ 2.0 compliant
Preset continuous mode: 10 useconds to 16,777,216 useconds
Preset trigger mode: 10 useconds to 16,777,216 useconds
Pulse width mode: 10 useconds to Unlimited
Auto iris lens, electronic iris and AGC (ON/OFF)
0 to 20.4 dB
Gamma 1.0 (Factory default) or uploadable gamma table
Programmable AOI setting via the communication
Selectable ON/OFF via the communication
Available on RGB output
N/A
Auto, manual and push-to-set white balance
is available on both Raw data output
N/A
and RGB output
Edge preset trigger, Pulse width trigger (unlimited long exposure)
UART communication through Ethernet port
One opto-isolated input and two open-collector outputs
DC IRIS control input with video level target, peak/average and zone weight settings
via the communication
+10.8 to +26.4 Vdc
Less than 5.0 W
11
Rev 3.01
STC-GE Series
Product
Mechanical
Specifications
Dimensions
Optical Filter
Optical Center Accuracy
Material
Lens Mount
Connectors
Camera Mount Screws
Weight
Environmental
Specifications
Operational
temperature
Minimum
Maximum
Storage Temperature
Vibration
Shock
Standard Compliancy
RoHS
STC-GEC152A
STC-GE152A
35 (W) x 35 (H) x 50.6 (D) mm excluding connectors
IR cut filter on
No filter
Positional accuracy in H and V directions: +/- 0.3 mm
Rotational accuracy of H and V: +/- 1.5 deg.
Aluminum (AC)
C mount
RJ45 connector
Power/IO connector: HR10A-7R-6PB (Hirose) or equivalent
DC IRIS lens connector: M1951 (EMUDEN) or equivalent
Two 1/4” Tripod screw holes: (One on each top and bottom plate),
Twelve M4 screws holes: (Four on each top and bottom plate, two on each side plate)
Approximately 120 g
Environmental Temperature -5⁰C
Camera housing temperature (top plate) shall not exceed 65⁰C
(This corresponds to an environmental temperature of approximately 35⁰C)
-30⁰C to 65⁰C
20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each
Acceleration 38G, half amplitude 6ms, 3 directions 3 times each
EMS: EN61000-6-2, EMI: EN55011
RoHS Compliant
Note: Please use this camera in surrounding temperature conditions that are less than 35⁰C or in conditions where the
camera’s top case plate is less than 65⁰C.
When the camera is used in surrounding temperatures that exceed 35⁰C, please make sure that the camera is set
up to properly radiate heat (maintaining the camera’s top case plate’s temperature to be less than 65⁰C).
Taking these steps will maintain the heat rating of the electronic components of the camera.
Product Specifications
12
Rev 3.01
STC-GE Series
Spectral Sensitivity Characteristics
STC-GE152A
1
Relative Response
0.8
0.6
0.4
0.2
0
400
500
600
700
Wave length [nm]
800
900
1000
STC-GEC152A (with IR cut filter)
1
G
Relative Response
0.8
R
B
0.6
IR cut filter
0.4
0.2
0
400
500
600
700
Wave length [nm]
Product Specifications
13
Rev 3.01
STC-GE Series
4. STC-GE202A / STC-GEC202A
Product
Electronic
Specifications
STC-GEC202A
1/1.8” Interline UXGA color
progressive CCD: ICX274AQ
Imager
Total Picture Elements
Active Picture Elements
Chip Size
Cell Size
Scanning System
Vertical Frequency (Frame Rate)
Horizontal Frequency
Pixel Frequency
@ 8bit output
Noise Level
@ 10bit output
@ 12bit output
Minimum Scene Illumination
Sync. System
Video Output
Interface
Protocol
Shutter Speed
ALC
Gain
Gamma
AOI Function
Smear Reduction
Color Interpolation
White Balance Function
Trigger Mode
Communication
I/Os
Auto IRIS lens control
Power
Product Specifications
Input Voltage
Consumption
STC-GE202A
1/1.8” Interline UXGA monochrome
progressive CCD: ICX274AL
1688 (H) x 1246 (V)
UXGA: 1624 (H) x 1236 (V)
8.5 (H) x 6.8 (V) mm
4.4 (H) x 4.4 (V) µm
Progressive
15.31668 Hz at full resolution
0.29261 to 61.26674 Hz adjustable via the communication
Maximum frame rate depends on the AOI setting
Maximum frame rate of the camera(61.26674) is 230 vertical resolution AOI setting
19.1761 kHz
36.8181 MHz
≤ 3 Digit (Gain 0 dB)
≤ 12 Digit (Gain 0 dB)
≤ 48 Digit (Gain 0 dB)
7.27 Lux at F1.2, 15.31668 Hz
0.16 Lux at F1.2, 15.31668 Hz
Internal
Digital 8, 10 or 12 bit Raw Data
or
Digital 8, 10 or 12 bit Raw Data
RGB 8 bit
IEEE802.3 (1000BASE-T)
GigE Vision® 1.2 and GenICam™ 2.0 compliant
Preset continuous mode: 1 useconds to 16,777,216 useconds
Preset trigger mode: 1 useconds to 16,777,216 useconds
Pulse width mode: 1 useconds to Unlimited
Auto iris lens, electronic iris and AGC (ON/OFF)
0 to 20.4 dB
Gamma 1.0 (Factory default) or uploadable gamma table
Programmable AOI setting via the communication
Selectable ON/OFF via the communication
Available on RGB output
N/A
Auto, manual and push-to-set white balance
is available on both Raw data output
N/A
and RGB output
Edge preset trigger, Pulse width trigger (unlimited long exposure)
UART Communication through Ethernet port
One opto-isolated input and two open-collector outputs
DC IRIS control input with video level target, peak/average and zone weight settings
via the communication
+10.8 to +26.4 Vdc
Less than 5.00 W
14
Rev 3.01
STC-GE Series
Product
Mechanical
Specifications
Dimensions
Optical Filter
Optical Center Accuracy
Material
Lens Mount
Connectors
Camera Mount Screws
Weight
Environmental
Specifications
Operational
Temperature
Minimum
Maximum
Storage temperature
Vibration
Shock
Standard Compliancy
RoHS
STC-GEC202A
STC-GE202A
35 (W) x 35 (H) x 50.6 (D) mm excluding connectors
IR cut filter on
No filter
Positional accuracy in H and V directions: +/- 0.3 mm
Rotational accuracy of H and V: +/- 1.5 deg.
Aluminum (AC)
C mount
RJ45 connector
Power/IO connector: HR10A-7R-6PB (Hirose) or equivalent
DC IRIS lens connector: M1951 (EMUDEN) or equivalent
Two 1/4” Tripod screw holes: (One on each top and bottom plate),
Twelve M4 screws holes: (Four on each top and bottom plate, two on each side plate)
Approximately 120 g
Environmental Temperature -5⁰C
Camera housing temperature (top plate) shall not exceed 65⁰C
(This corresponds to an environmental temperature of approximately 35⁰C)
Environmental Temperature: -30⁰C to 65⁰C
20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each
Acceleration 38G, half amplitude 6ms, 3 directions 3 times each
EMS: EN61000-6-2, EMI: EN55011
RoHS Compliant
Note: Please use this camera in surrounding temperature conditions that are less than 35⁰C or in conditions where the
camera’s top case plate is less than 65⁰C.
When the camera is used in surrounding temperatures that exceed 35⁰C, please make sure that the camera is set
up to properly radiate heat (maintaining the camera’s top case plate’s temperature to be less than 65⁰C).
Taking these steps will maintain the heat rating of the electronic components of the camera.
Product Specifications
15
Rev 3.01
STC-GE Series
Spectral Sensitivity Characteristics
STC-GE202A
1
Relative Response
0.8
0.6
0.4
0.2
0
400
500
600
700
Wave length [nm]
800
900
1000
STC-GEC202A (with IR cut filter)
1
G
Relative Response
0.8
R
B
0.6
IR cut filter
0.4
0.2
0
400
500
600
700
Wave length [nm]
Product Specifications
16
Rev 3.01
STC-GE Series
B. Connector Specifications
1. RJ45 Connector:
Caution: This product is not a PoE type. Apply power (+10.8 to +26.4Vdc) only through the Power/IO connector.
Pin Assignment:
Pin No.
1
2
3
4
5
6
7
8
Signal Name
TA+
TATB+
TC+
TCTBTD+
TD-
LED Information:
Green LED
Green Light ON
Green Light ON
Light OFF
Yellow LED
Orange Light ON
Orange Light Blinking
Orange Light Blinking
Status
Power ON
1 Gb Transferring
100 Mb Transferring
Green light: ON
Yellow light: Blinking
1 Gb Transferring
The camera is powered-on
Green light: OFF
Yellow light: Blinking
100 Mb Transferring
Please use a 1Gb supported NIC, HUB and LAN cable. Check that the NIC and HUB being used is “1Gb
transferring”.
Damaging or mishandling the CAT5e cable may cause the transferring speed to change from 1Gb to
100Mb. If this happens, please replace the CAT5e cable.
Product Specifications
17
Rev 3.01
STC-GE Series
2. Power/IO Connector: Connector: HR10A-7R-6PB (Hirose) or equivalent.
This connector is for the DC power input and the input and output signals.
Pin Assignment:
Pin No.
1
2
3
4
5
6
Signal Name
GND
IO_OUT1
IO_OUT2
TRG_InTRG_In+
POWER IN
IN/OUT
IN
OUT
OUT
IN
IN
IN
Signals
GND
+3.3V LVTTL
+3.3V LVTTL
Isolated Isolated +
+10.8 to +26.4 Vdc
Initial Output
FrameTriggerWait
ExposureActive
a. Input Signal
TRG IN: Input the trigger signal
High: +3.0 to +26.4V
Low: Smaller than 1.0V
b. Output Signals
Set the output signals from the power/IO connector.
The following six output signals are selectable with the software or communication.
1) FrameTriggerWait
The user can check the camera condition (camera exposure and image output processing by the trigger
signal with this FrameTriggerWait signal).
a) High status (3.3V): No processing by the trigger signal. The camera accepts the trigger signal.
b) Low status (0V):
The camera is exposed and the image output processes by the trigger signal.
The camera default setting is the input trigger signal is INVALID while at the low status of this signal. When
the exposure starts while the image output by the next trigger signal, please change the camera setting
(Device code: 00H, Command: 13H) to accept the trigger signal while the image outputs.
The noise appears on the image when the exposure begins while the image is output. The noise appears on
the image when the start exposure while the image is output. In this case, please change the “H reset” for
the exposure start mode (Device code: 00H, Command: 12H) to change the exposure start point to the next
HD timing.
2) UserOutput
The status of the UserOutput signal can change with the “UserOutputValue”.
3) ExposureActive
The user can check the exposure time with the ExposureActive signal.
a) High status (3.3V): The camera is exposing
b) Low status (0V): The camera is not exposed
4) TriggerAuxiliary
The TriggerAuxiliary signal is the input trigger signal.
Product Specifications
18
Rev 3.01
STC-GE Series
5) TriggerInternal
The TriggerInternal signal is the input trigger signal with the trigger delay time.
6) SensorReadOut
The SensorReadOut signal is the FVAL signal, which is the image output period of the time.
3. DC IRIS Lens Connector:
M1951 (EMUDEN) or equivalent.
Pin Assignment:
Pin No.
1
2
3
4
Product Specifications
Signal Name
DAMPDAMP+
DRIVE+
DRIVE-
19
3 4
1 2
Rev 3.01
STC-GE Series
II. I/O Circuits
HR10A-7R-6PB (HIROSE)
or equivalent connector
6
5
4
+3.3V
3
2
2.2K
1
6
1
4
3
+10.8 to +26.4V
Trigger_In+
Trigger_InIO_Out
IO_Out
GND
+3 to +26.4V
3 to 5mA
Trigger Signal
Customer GND
TOSHIBA TLP181
+3.3V
3
1K
2
RN1105MFV
1
TOSHIBA
+3.3V
3
1K
2
RN1105MFV
1
TOSHIBA
Product Specifications
20
Rev 3.01
STC-GE Series
III. Dimensions
12
2-M4 depth 4 (Top and bottom sides)
15.5
16.8
30.2
15
25
14.5
Tripod depth 5 (Top and bottom sides)
2-φ2.0 depth 2.5 H8
50.6
35
14.5
25
φ30
35
1"-32UNF (C mount)
2-M4 depth 4 (All four sides)
Unit: mm
Product Specifications
21
Rev 3.01
STC-GE Series
Revision
Rev.
1.0
1.1
Date
Aug. 8, 2009
Aug. 18, 2009
1.2
Sept. 2, 2009
1.3
Sept. 8, 2009
1.4
Dec. 8, 2009
1.5
Mar. 13, 2010
1.6
May 6, 2010
1.7
May 17, 2010
1.8
May 21, 2010
1.9
July 28, 2010
2.0
Sept. 17, 2010
Product Specifications
Change
New Document
Update
1) Electronic Specifications
Update
1) Dimensions (Change drawing)
2) Mechanical Specifications (Change dimensions)
3) Mechanical Specifications (Change description of optical filter)
4) Electronic Specifications (Add CCD out method for STC-GE/GEC500A)
5) Electronic Specifications (Change description of plus width trigger)
Update
1) Imager for GE/GEC83A is XGA
2) Pixel Frequency for GE/GEC500A is 64MHz
3) Video output: “Digital 8, 10, or 12 bit Raw Data GigE Vision”
4) Power Supply  Power
5) Gamma: “Programmable gamma setting via the communication (Factory default as
1.0”
6) ROI function added
7) Communication: Communication through Ethernet Connector
8) Page 11: Description of Interface connector changed
Update
1) Change power/IO connector, IO configurations and related specifications.
Update
1) Deleted “STC-GE133A/GEC133A
2) Dimensions (Change Drawing)
3) Mechanical Specifications (Changed Dimensions)
4) Electronic Specifications (Delete RGB 10/12 bit from video output)
Update
1) Electronic Spec: Changed auto iris lens type from DC iris to Video Iris
2) Electronic Spec: Changed input power range from “9 to 28Vdc” to “10.8 to
26.4 Vdc”
3) Electronic Spec: Entered weight
4) Mechanical Spec: Changed auto iris lens type
5) Connector Spec: Changed input power range and auto iris lens type
Update
1) Electronic Spec: Changed S/N Ratio to Noise Level
Update
1) Electronic Spec: Changed Video Output
2) Electronic Spec: Changed ALC
3) Electronic Spec: Smear Reduction
4) Electronic Spec: Added Color Interpolation row
5) Electronic Spec: Added White Balance Function row
6) Electronic Spec: Added I/O’s row
7) Mechanical Spec: Dimension: Changed 49.5(D) to 49.6(D)
8) Mechanical Spec: Changed wording of Optical Filter
9) Mechanical Spec: Changed wording of Camera Mount Screws
10) Pg.15, Section 2.Power/IO Connector: Changed pin no. 4&5 last column
Update
1) Electronic specifications (Change minimum scene illumination)
2) Electronic specifications (Change power consumption)
3) Electronic specifications (Change the shutter speed)
4) Electronic specifications
(Change auto Iris lens type from Video iris to DC iris)
5) Change dimensions
6) Mechanical specifications
(Change optical filter, color model has IR cut filter)
7) Environmental specifications
(Delete humidity)
Udate
1) Add I/O circuits
2) Connector specifications
(Add the explanation of the TRG READY OUT and EXP OUT signal)
22
Notes
Note: Per STJ’s
noted changes to
ver 1.8. Changes
to the minimum
illumination and
the power
consumption were
not present. Both
are still TBD
status.
Rev 3.01
STC-GE Series
Rev.
2.3
Date
Nov. 29, 2010
(2.1~2.3)
2.4
2.5
2.6
March 3, 2011
2.7
March 15, 2011
2.8
April 1, 2011
2.9
July 8, 2011
3.0
July 27, 2011
3.01
August 24, 2011
Product Specifications
Change
Update
1) Electronic specifications (Delete the scanning method)
2) Electronic specifications (Change the frame rate)
3) Electronic specifications (Change the protocol)
4) Electronic specifications (Change the shutter speed)
5) Electronic specifications (Change the gain range)
6) Electronic specifications (Change ROI to AOI)
7) Electronic specifications (Change number of the input for I/O’s)
8) Mechanical specifications (Change the dimensions)
9) Mechanical specifications (Change the screw holes)
10) Environmental specifications (Change the temperature)
11) Connector specifications (Change the power/IO connector)
12) I/O circuits (Change the I/O circuits)
13) Dimensions (Change the drawing)
14) Change the dimension for STC-GE500A/GEC500A
Update
1) Connector spec (changed the description for the input and output signals)
2) Changed the I/O circuits
3) Electronic spec (Change horizontal and pixel frequency for the GE/GEC83A
4) Electronic spec (change frame rate)
5) Electronic spec (change the minimum scene illumination)
6) Environmental spec (Change operational temp)
7) Change note about the operational temp
8) Connector spec (Add the LED info for RJ45 connector)
Update
1) Connector spec (change the initial signal for the Power/IO connector)
Notes
Received revision
2.4 & 2.5 on 1/14
Update
1) Added the spectral sensitivity characteristics to each resolution.
Update
1) Mechanical Spec (Added Optical Center Accuracy)
2) Environmental Spec (Changed operational temperature)
3) Electronic Spec (Change the frame rate for the GE/GEC500A)
4) Environmental Spec (Revise shock and standard conformity)
Update
1) Connector specifications (Change the LED information for the RJ45 connector)
2) Environmental specifications(Changed the operational temperature)
Update
1) Change the I/O circuits
2) Electronic Spec (Change frame rate for 83 and 152)
3) Separate the STC-GE/GEC500A from document
Update
1) Electronic Spec (revised the imager part number for STC-GEC83A)
Update
Changed the output signal name (from FrameActive to SensorReadOut)
23
Rev 3.01
STC-GE Series
Sensor Technologies America, Inc.
1345 Valwood Pkwy, Suite 320
Carrollton, Texas 75006-6891
TEL (972) 481-9223 FAX (972) 481-9209
URL http://www.sentechamerica.com/
Sensor Technology Co., Ltd.
7F, Harada Center Building
9-17, Naka cho 4chrome
Atsugi-city, Kanagawa
243-0018 Japan
TEL +81-46-295-7061 FAX +81-46-295-7066
URL http://www.sentech.co.jp/
Taiwan Sensor Technology, Inc.
3F-6, No. 9, Aiguo W, Rd,. Jhong Jheng District
Taipei City 100, Taiwan, R.O.C.
TEL 886-2-2383-2331 FAX 886-2-2370-8775
EMAIL: sentech0501@yahoo.com.tw
Product Specifications
24
Rev 3.01