Chery V5 User`s manual

Preface
ADVICE
User’s Manual clarifies the agreement between Chery Automobile Co., Ltd. and the User on the product
quality warranty responsibility and the establishment and termination of after-sales service rights and responsibilities.
Please read this User’s Manual carefully before using our products.
User’s Manual for Chery V5
Sincere congratulations on your own of one Chery V5! Also, with great appreciation on your great favor on our company and our products.
The personnel of Chery authorized service station are trained with good professional trainings, which will sincerely provide you with the top
quality services.
Chery V5 features advanced technology and prominent performances. Your choice of Chery V5 will prove that you have extra-high
requirements on the vehicle performance and design.
Please read this manual carefully, since the information contained in this manual can let you understand how to operate and maintain your
vehicle properly so as to achieve the driving pleasure to the maximum extent.
This user’s manual applies to the Chery V5.
Chery Automobile Co., Ltd.
1
Preface
This manual is established based on the
detailed conditions of V5 vehicles
manufactured by Chery Automobile Co.,
Ltd., which only applies to the V5 vehicles
manufactured by Chery Automobile Co.,
Ltd. This manual included the latest
information up to the date when this
manual is printed. Chery Automobile Co.,
Ltd. will be wholly responsible for the
modification and explanation of this
manual and reserved the rights for product
replacement after the print of this manual
without any prior notice. Some pictures in
this manual are illustrations for reference
only. The real article should take
precedence in case of any conflict between
the pictures and the real articles.
This manual is the main evidence for
vehicle quality warranty and first free
maintenance. Please keep this manual in
your vehicle so that it’s available
whenever you need it. When to resell this
vehicle, please hand over this manual and
all the documentation attached with this
vehicle to the new owner so that they are
available whenever the new owner needs
them.
not be accepted by the Chery authorized
service station.
Special Statement
Please make sure to read this manual
before using this product.
Chery Automobile Co., Ltd. (hereafter
referred as “Our Company” or “Chery
Company”)
defined
the
technical
maintenance regulations of the new
vehicle run in and of maintenance at
various stages for the products, of which
including the first 5,000 km maintenance.
Please make sure to abide by above
regulations
since
above
defined
maintenances are vital to the safety
operation and the maintaining of good
running conditions of your vehicle.
Your claim right will be forfeited in case
of the failure of your vehicle or vehicle
parts that arising from the abuse,
negligence, improper use, the maintenance
not in accordance with the specified
mileage/period, or the warranty evidence
not signed or stamped in accordance with
the requirements, or any unauthorized
refit/attachment. Therefore, any direct or
indirect warranty application thereof will
Any problems of Our Company’s products
during use must be overhauled by the
Chery authorized service station. During
the overhaul process, Chery authorized
service station is entitled to decide based
on the conditions to perform the repair by
means of repair or the replacement of
equivalent parts.
If you encountered anything unclear
during the careful reading of this manual,
Chery Company and Chery authorized
service station will give you the detailed
explanation. Also, the precious advices of
vast users are highly welcomed.
Wish you pleasant driving!
Chery Automobile Co., Ltd. reserved all
copyrights of this menu
2
Summary
Chapter 1
Summary
3
Summary
vehicle driving as well as enjoy the
Before
reading
this
User’s
Manual,
you
should
understand
following things.
pleasure thereof.
This
Any improper operation may damage your
claim right.
The
periodical
maintenance
to your
In order to operate your vehicle properly
performance and used value of your
and guarantee your rights and benefits,
vehicle. The Chery authorized service
please spend some time to read this
stations all over the country boasted
manual carefully.
numerous repair experts to provide you
with service anytime. The repair personnel
and regular maintenance and care, with the
purpose for your familiarity with the
operation of your vehicle. Only the more
understanding
to
your
vehicle
can
guarantee the safety and economy of the
manual
defined
the
maximum
equipment
scope
installed in accordance with the
series V5 model plan till the print date,
vehicle will help maintain the driving
instructions and hints on the daily driving
Equipment Scope
possible
vehicle as well as may be deprived of your
Thanks for your purchase of Chery vehicle.
This manual provides the important
„
of all authorized service stations, who
passed the professional trainings, can
properly repair your vehicle and vehicle
equipment. The spare parts in Chery
authorized service station are of Chery
genuine spare parts.
namely for all the standard equipment and
optional equipment in series V5 model,
some equipment may be supplied in the
future or may be only available in certain
markets. Therefore, some items in this
manual may not apply to your vehicle.
„
Alarm
Symbols
within This Manual
During the vehicle operation, how to
reduce the damage to the vehicle and the
vehicle equipment and how to avoid the
person injury? In this manual, the answer
for such question is included in the
4
Summary
explanation for the alarm symbols with
disposing the used cleaning articles and
The dealer should verify the entire vehicle
triangle. Please read carefully and abide
lubricating materials in accordance with
performance and introduce the operation
by the contents thereof.
the laws and regulations. This manual
knowledge of the vehicle against the
displayed the information on this aspect by
“Chery Vehicle Sale & Delivery Card”
means of tree symbol.
that to be dually signed by the salesman
The
equipment
marked
with
asterisk (*) is only used in lot
and the user.
size on certain model structures, which is
supplied as optional equipment for some
models or is only available in certain
markets.
„
New
Inspection
Vehicle
„
Run in of New Vehicle
Due to the manufacture and assembling
Before deliver the vehicle to you, the
deviations,
When this symbol is present on
dealer of Chery Company has already
between the moving components of the
the vehicle, make sure to read
performed
in
new vehicle at the initial stage of
accordance with the regulations of Chery
operation will be much greater than the
Automobile Co., Ltd. The dealer of Chery
ones of normal condition. The run in
Company should fill in the vehicle
effects of the vehicle at the initial stage of
delivery date in the "Vehicle Delivery
operation will exert great influence on the
Inspection Certificate” column of this
use lifetime, working reliability and
manual and seal with the stamp of dealing
economy of the vehicle, therefore, the use
agency.
of new vehicle must abide by the run in
the related chapters of this manual before
any operations.
We
must
contribute
our
responsibility and liability in the working
of environmental protection.
It’s the
important step to achieve such objective
by operating your vehicle properly and
the
vehicle
inspection
the
frication
resistances
5
Summary
tachometer, the allowed short period top
the beginning of use; therefore, the tires
engine speed is 6,000 r/min. During the
also need run in. The vehicle speed should
Run in Regulation within 1,000
km
manual gearshift, make sure to shift to the
be relative low during first 100 km driving
next high gear when the engine tachometer
and the driving should be extremely
y
Full speed driving is absolutely
indicator reached red indication area at the
careful.
prohibited.
latest.
regulations strictly.
y
y
Avoid the running of engine at
run in, since the brake doesn't have ideal
the speed above 100 km/h.
unnecessary high speed. The
friction force during first 200 km driving.
Avoid driving at the top speed at
earliest shift to high gear will help save the
During this period the brake effects are a
whichever gear.
fuel, reduce the working noise as well as
little poor, therefore the pressure on brake
diminish the environmental pollution.
pedal may be reasonably increased. Such
Run in Regulation from 1,000 km
to 1,500 km
y
The new brake friction lining also needs
Generally, do not drive the vehicle at
Increase to the top speed gradually or
drive at the allowable max engine
speed.
The engine speed should not be excessive
low during driving. Shift to proper gear at
reasonable time.
When at cold condition, do not run the
engine at top speed no matter at neutral
Notice during Run in Period
gear or any other drive gear.
For the driving of vehicles with engine
The new tires don’t have best adhesion at
condition also applies to the each time
when replaced with new friction lining.
When the new vehicle traveled for 800km,
the wheel nuts must be re-tightened to the
specified torque. Please refer to the
chapter “Specification and Parameters” of
this manual for correct torque values. Also,
6
Summary
if the wheel has been replaced or the
wheel nuts have been loosened, then the
wheel nuts should be re-tightened in
accordance with the specified torque after
traveled for 800km.
„
“One-To-One” Service
In order to provide you with better service
and vehicle use, the dealer of Chery
Company will appoint one service counsel
to serve you at the purchase of your
vehicle. In case of any problems during
your vehicle use, you may contact your
service counsel, who will provide you
with best services.
7
Summary
Vehicle Delivery Inspection Evidence
This is to certify that this vehicle has completed the
vehicle delivery inspection defined by Chery Automobile Co., Ltd.
and its quality met with the technical specification of Chery
Automobile Co., Ltd.
Vehicle Register No.:
Vehicle Owner Name (Unit) Responsible Service Station Name
——————————————————
—————————————————————
——————————————————
—————————————————————
Vehicle Delivery Date: _____________
Address————————————— Responsible————————————
Dealer Stamp:
——————————————————————
Tel:—————————————————
Tel:——————————————
8
Summary
Vehicle Delivery Date
Dealer Stamp
Model:
Body VIN No:
Engine Serial No.:
Transmission Serial No.:
9
Summary
Chery Vehicle Sale & Delivery Sheet
Entire Vehicle Performance
Catego
ry
No.
Item
Whether inspected OK and
clearly explained
1
Engine
Yes
□
No
□
2
Engine oil, brake liquid, steering liquid, coolant, battery liquid, windscreen
cleaning liquid.
Yes
□
No
□
3
VIN number, engine serial number, nameplate and other identifications
Yes
□
No
□
4
Entire vehicle locks
Yes
□
No
□
5
Entire vehicle lamps, including head lamp, turn lamp, fog lamp, combined lamp,
compartment lamp, brake lamp, backup lamp, tail lamp, reading lamp, door
lamp, and instrument lamp.
Yes
□
No
□
6
Windscreen glass and body paint
Yes
□
No
□
7
Speedometer, engine tachometer, odometer
Yes
□
No
□
8
Hub cap, spare tire in luggage boot, vehicle attached tools and entire vehicle
operation manual
Yes
□
No
□
9
Safety belt, seat, cigarette lighter, A/C switch and vent, glove box and sun visor.
Yes
□
No
□
10
Glass lifter, rear view mirror, wiper, washer, horn, sunroof, backup radar, vehicle
telephone, radio (CD player) and antenna.
Yes
□
No
□
10
Summary
1
93# gasoline fuel
Yes
□
No
□
2
Normal operation during run in.
Yes
□
No
□
3
Operation of entire vehicle lamps
Yes
□
No
□
4
Meaning of alarm indicators
Yes
□
No
□
5
Correct maintenance period and mileage
Yes
□
No
□
wled
6
Vehicle maintenance items in winter and summer.
Yes
□
No
□
ge
7
Correct understanding of cooling system/coolant usage.
Yes
□
No
□
8
Correct operation of A/C
Yes
□
No
□
9
Notices for vehicle start
Yes
□
No
□
10
Correct operation of audio equipment
Yes
□
No
□
11
Correct operation of sunroof
Yes
□
No
□
Oper
ation
Kno
Salesman Signature:
Date:
User Signature:
Date:
11
Summary
Vehicle Purchase Date
Model:
Following items should be validated by the user:
I. Related items confirmation at vehicle delivery (“√" for Yes as
“×” for No)
□ Basic vehicle operation method has been introduced and the
onsite delivery inspection is certified OK.
□ Quality warranty policy has been introduced.
□ Vehicle driving notices has been introduced.
□ The importance of vehicle periodical maintenance and
maintenance period/mileage has been introduced.
□ The importance of vehicle maintenance/repair at Chery
authorized service station has been noted.
□ User’s Manual has been handed over and the reading is
reminded.
□ The function and operation method of service hotline of Chery
Company has been noted.
II. “One-To-One” counseling service mode introduction (“√” for
Yes as “×” for No)
□ Contact the service counsel instead of anyone else in case of any
problems or needs.
□ The service counsel appointed by the service station is the
exclusive person to communicate and contact with the user.
□ One user is only served by one service counsel: "One-To-One”
User may choose other service counsel when dissatisfied with
current service counsel.
III. Major job introduction of service counsel (“√” for Yes as “×”
for No).
□ Repair maintenance service reception
□ Complaint acceptance
□ Periodical maintenance reminding visits
□ Repair/Maintenance counsel explanation
□ Periodical greeting visits
□ Repair/maintenance reservation acceptance
□ Service activity reminding visits
□ Annual authentication reminding/acceptance
□ Important festival greeting
□ Other activities of user’s needs
IV. Establishment of “One-To-One” counseling service
relationship.
□
Form One
“One-To-One” Counseling Service Card
User Name:
Sales Agency:
Vehicle VIN Number:
Service Counsel Card
User Signature/Date:
Service Counsel Signature/Date:
12
Summary
User Name:
Sales Agency:
Vehicle VIN Number:
Vehicle Purchase Date
Model:
Following items should be validated by the user:
I. Related items confirmation at vehicle delivery (“√" for Yes as
“×” for No)
□ Basic vehicle operation method has been introduced and the
onsite delivery inspection is certified OK.
□ Quality warranty policy has been introduced.
□ Vehicle driving notices has been introduced.
□ The importance of vehicle periodical maintenance and
maintenance period/mileage has been introduced.
□ The importance of vehicle maintenance/repair at Chery
authorized service station has been noted.
□ User’s Manual has been handed over and the reading is
reminded.
□ The function and operation method of service hotline of Chery
Company has been noted.
II. “One-To-One” counseling service mode introduction (“√” for
Yes as “×” for No)
□ Contact the service counsel instead of anyone else in case of any
problems or needs.
□ The service counsel appointed by the service station is the
exclusive person to communicate and contact with the user.
□ One user is only served by one service counsel: "One-To-One”
□ User may choose other service counsel when dissatisfied with
current service counsel.
III. Major job introduction of service counsel (“√” for Yes as “×”
for No).
□ Repair maintenance service reception
□ Complaint acceptance
□ Periodical maintenance reminding visits
□ Repair/Maintenance counsel explanation
□ Periodical greeting visits
□ Repair/maintenance reservation acceptance
□ Service activity reminding visits
□ Annual authentication reminding/acceptance
□ Important festival greeting
□ Other activities of user’s needs
IV. Establishment of “One-To-One” counseling service
relationship.
Form Two
“One-To-One” Counseling Service Card
Service Counsel Card
User Signature/Date:
Service Counsel Signature/Date:
13
Interior Device Operation and Adjustment
Common Vehicle Symbol Instruction
Symbol
A/C
Definition
Symbol
Definition
Symbol
Definition
Engine
self-examination
trouble light
Anti-lock
system
Glass lifter switch
prohibited
Safety warning
Engine oil pressure
alarm lamp
Rear fog light
Throttle
indicator
Coolant
temperature
overheating alarm
(red indicator)
brake
trouble
Position lamp
Front fog light
Cigarette lighter
Coolant
temperature
normal indicator
(green indicator)
A/C system
Brake
trouble
lamp
Luggage boot door
opened
system
alarm
15
Interior Device Operation and Adjustment
Symbol
Definition
Symbol
Definition
Symbol
Definition
Battery
Fasten the safety
belt
Windscreen
cleaning
High beam lamp
Danger
alarm lamp
Horn
Low beam lamp
Power + pole
Seat heating
Head lamp switch
Air bag trouble
indicator
Windscreen
defrosting
Parking
indicator
Low fuel level
alarm indicator
Rear windscreen
heating indicator
External rear view
mirror heating
External
circulation
Lock indicator
brake
flash
air
16
Interior Device Operation and Adjustment
Symbol
Definition
Symbol
Definition
Symbol
Definition
Unlock indicator
Interior
lamp
switch indicator
Internal
circulation
Door and luggage
boot cover not
closed alarm lamp
Sound alarm
Air
bag
identification
Vehicle
maintenance
indicator
Right
indicator
turn
air
Left turn indicator
17
Interior Device Operation and Adjustment
Symbol
Definition
Transmission
gear
position indicator
Backup
radar
distance display
Fuel
consumption
display
18
Interior Device Operation and Adjustment
Chapter 2
Interior Device Operation and Adjustment
19
Interior Device Operation and Adjustment
Steering
Wheel/
Ignition Switch
The
combined
steering
wheel
lock/ignition switch has following key
positions:
LOCK - Ignition switch is turned off
as the steering wheel is locked.
When the key is pulled out from the
ignition switch, the steering wheel lock
will actuate to lock the steering wheel.
In order to lock the steering wheel,
rotate the steering wheel once after the
withdrawal of the key, till the
engagement sound as the steering
wheel is locked.
ACC – Unlock of steering system.
When the circuits of the electrical
accessories are turned on, the small
electrical appliances such as interior
lamp can be operated, however the
ignition switch and the main electrical
circuits are all turned off.
The ignition switch is equipped with
repeated start proof device internally.
Once the engine is running, such
device can prevent the mis-start of the
starter so as to avoid the damage to the
starter and the engine flywheel.
If it fails or has difficulty to rotate the
key from the LOCK position to such
position, the lock mechanism of the
steering wheel can be released by rotate
the steering wheel around slightly.
If the start fails, then it’s must to rotate
the ignition key to LOCK position
before rotate to this position for restart.
After start, the key will bounce back to
ON position when the key is released
The ignition switch key should not be
left at such position overlong so as to
avoid the depletion of the battery
power.
ON – All electrical circuits can operate
once the ignition circuit is turned on.
The alarm lamp and the indicator will
light. This is the normal position of key
during driving as well as the position
must be selected during vehicle towing.
The key must be released
once the engine is started.
Do not hold at the START
position for much longer.
Adjustment of Steering
Wheel
START – Turn on the start motor and
start the engine.
When the key is at such position, the
front headlamp and the electrical
devices
with
higher
power
consumption will be turned off.
20
Interior Device Operation and Adjustment
Horn
In order to drive the vehicle safely and
comfort, sometimes the height of the
steering wheel should be adjusted. At
such time, pull downward the
adjustment handle under the steering
pillar cover to release the handle and
then the steering wheel can slide
up-and-down. After adjusted to
position, pull upward the adjustment
handle to lock position and lock the
position of steering wheel.
Do not adjust the steering wheel
during driving.
Press the button with
Windscreen Wiper and
Washing System
mark on
the steering wheel to operate the horn.
The horn is still operational under the
status that the ignition switch is turned
off.
In cold season, make sure to
check if the wiper blade is
frozen onto the windscreen
before using the wiper. If frozen onto
the windscreen, then it’s the must to
defreeze the blade before use;
otherwise it will cause the damage of
the wiper motor.
If the windscreen has obstacles such
as snow accumulation, the operation
of wiper will also cause the damage
of the wiper motor.
Please remove the obstacles before
the operation of the wiper.
Do not operate the wiper on the dry
windscreen; otherwise the windscreen
glass will be scratched and it will
cause permanent damage to the wiper.
The wiper can be actuated only when
21
Interior Device Operation and Adjustment
the ignition switch is turned on. The
Move the control lever downward from
front windscreen switch totally has 5
OFF position to INT gear after passing
positions and will stop at OFF position
through one position.
when unused.
The wiper controller will operate
automatically once for every certain
Single Wiping
interval.
Move the control lever downward from
OFF position to HI gear after passing
through three positions.
Water Spray Switch
Normal Wiping
Pull the control lever upward to MIST
gear and the control lever will return to
When pull the switch handle toward the
OFF
steering wheel and hold, the cleaning
position
automatically
upon
release. The wiper will operate only
Move the control lever downward from
liquid will be sprayed out from the
once.
OFF position to LO gear after passing
water spray opening in front of the
Intermitted Wiping
through two positions.
windscreen and the wiper will operate
High Speed Wiping
accordingly. The water spray will stop
spray upon release of the switch and
the wiper will continue the operation
for several cycles.
22
Interior Device Operation and Adjustment
The operation period of
water spray should not
exceed 10 s for each time.
This operation is absolutely
prohibited when the reservoir has no
cleaning liquid; otherwise it may
cause the damage of the water spray
motor.
Rear Windscreen
Switch
Interior Review View
Mirror
window.
The back of the sun visor can store the
things such as driving license and
Dazzling proof fork
bridge & road passage fee invoice.
Door Control Switch
Rear
Wiper
Rear
Interior armrest
window
window safety
safety switch
switch
Driver side switch
Daytime driving
Nighttime driving
The wiper will start working when
rotate the switch head to the ON
position and will stop working when
rotate to the OFF position. When rotate
the switch head downward from the
OFF position and hold, the rear
windscreen water spray will start
working and the rear windscreen wiper
will act accordingly. The switch will
return to OFF position automatically
upon release of the switch.
Central lock switch
Electrical rear view mirror
switch
When to reduce the dazzling during
driving at night, pull the adjustment
lever backward to adjust the angle of
the rear view mirror.
Rear row passenger switch
Interior armrest
Window regulator
Sun Visor
The sun visor can be released from the
fixing clip and rotate towards the side
23
Interior Device Operation and Adjustment
Electrical External
View Mirror
Rear
it may fold the external rear view
the right side.
mirror inward manually. When to
After rotate the adjustment switch
leftward or rightward to position, pull
Middle Position
Left rear view mirror
adjustment position
adjust the external rear view mirror at
Right rear view
mirror
adjustment
position
the switch toward front, rear, left, or
right direction to adjust the up, down,
left or right position of the mirror. At
the finish of mirror position adjustment,
rotate the switch back to the middle
restore original position, fold the rear
view mirror outward till clip into the
correct position.
The images in the convex
rear view mirror seem
smaller and further than the
rear things. Notice not to
overestimate the real distance of the
things.
position.
Electrical Window
The electrical rear view mirror can be
Left Front Door
adjusted by the adjustment switch on
the driver side door. The adjustment
Left rear door window
regulator switch
switch will be operational only when
Left front door window
regulator switch
the ignition switch is turned on.
Rotate
the
adjustment
switch
Right rear door window
regulator switch
counter-clockwise to position to adjust
the external rear view mirror at the left
Right front door window
regulator switch
If necessary, such in the narrow space,
side; rotate clockwise to position to
24
Interior Device Operation and Adjustment
Rear Door
Door window regulator
switch
Interior armrest
function, namely the glass regulator
switch is still operational within 60 s
after the key is pulled out.
The driver side door trim panel also has
The
electrical
window
will
be
operational only when the ignition
switch is turned on.
Each window can be operated by the
control switch on the corresponding
door trim panel.
Each window glass has one-touch
one safety switch button. When this
function during the descending of the
button is pressed, the function of the
window glass, namely the glass will
electrical windows for right front door
descend to the end if the descending
and two rear doors will be disabled. At
switch is pressed for 1 s before release.
that time, the open/close of the
Besides the control switch for the
windows is only controlled by the
driver side window, the driver side door
switches
trim panel still has the control switches
recommended
for other three windows.
operation when there has child sitting
will stop at current position when the
switch is released during the ascending
or descending process of the window
glass.
the
to
driver
side.
conduct
It's
such
at the rear row seat.
Push down or lift up the switch to open
or close the window. The window glass
at
Rear
Switch
Window
Safety
Notice:
Cautions should be taken when closing
the window! The observation should be
noticed to avoid the occurrence of the
squeezing accident.
The glass regulator switch has time lag
25
Interior Device Operation and Adjustment
The heater of each seat will work when
before releasing. When to empty the
the corresponding switch is pressed.
ashtray, remove the internal ashtray
The further press of the switch will
case to empty.
stop the heating.
Driver Seat
Switch (
)
Driver
side
heater
switch
Rear row
seat
heater
switch
Heating
Secondar
y driver
side
heater
switch
Front Row Ashtray/
Cigarette Lighter
Front row
ashtray
Cigarette
lighter
Located in front of the gearshift lever.
The ashtray will eject out automatically
by pulling the cover plate forward once
The cigarette lighter is located at the
right side of the ashtray. When to use
the cigarette lighter, push it in and wait
it to eject out. The cigarette lighter is
still operational even when the ignition
26
Interior Device Operation and Adjustment
switch is turned off.
Backup Radar System
(
)
Do not leave the cigarette
lighter at the inserted
status for long period so
as to avoid the danger. Please
remove the cigarette lighter when
leaving the child alone in the
vehicle.
sound from approximate 90 cm and the
left/right rear corner radar probe will
The backup radar assistant system is
have rapid intermitted sound from
the device to inform the driver when
approximate 60 cm.(It may place the
the rear of the vehicle closes to the
hand at the probe to confirm the
obstacles by means of the alarm sound
detection scope)
rapid intermitted sound when the hand
reaches
the
central
radar
probe
approximate 60 cm.
Make sure it will change to
continual sound when the hand reaches
the radar probe approximate 35 cm.
The further approach will have no
sound or change to intermitted sound.
The rear of the vehicle is equipped
(buzzer) and distance display (display
with 4 probes. The detection distance
screen). (The following illustrations
of central parking radar probe is 0~150
may differ from the real articles and the
cm with the alarm sound comprised of
real articles should take precedence).
4 phases; The detection distance of the
left/right backup radar probe is 0~90
Before use, rotate the ignition key to
ON position and pull the gearshift lever
to the position of reverse gear. When
Confirm detection scope
Conform the detection scope
approach to the obstacle, the central
Make
radar probe will have slow intermitted
sure
that
the
cm with the alarm sound comprised of
3 phases. The detailed explanation is as
slow
intermitted sound will change to the
follows: (C: Central radar probe; L/R:
Left/right radar probe; the distance
27
Interior Device Operation and Adjustment
display will take 5 cm as one jump
grade. The display will be 120 cm if the
real distance is 123 cm.
The parking radar probe will
detect the nearest object.
It should
be noted that it may not detect the
bumper of the vehicles with higher
body height.
Backup
Radar
Probe
Position
C
Based on the change of the
specification, the contents of this
manual may differ from the real
vehicle. Please accept our apology.
Wipe with cloth or wash with
water (low pressure) the snow or mud
that stuck on the surface of backup
radar
probe.
C/L/R
Obstacle
Distance
Approximate
within 150
cm
Approximate
within 90 cm
C/L/R
Approximate
within 60 cm
C/L/R
Approximate
within 35 cm
Alarm Sound
The
high
pressure
water
flow such as
squirt gun or the
great
foreign
force
may
result
the
malfunctions.
Slow intermitted
sound of “dee…
dee… dee…”
High pressure
water flow
Slow intermitted
sound of “dee…
dee… dee…”
Rapid intermitted
sound of “dee
Do not apply squeezing or impact on
dee dee…”
the surface of the radar probe.
Continuous
sound
of
If the radar doesn’t alarm even closing
“Dee............."
to the obstacles, please check
following items:
28
Interior Device Operation and Adjustment
Whether the surface of radar
probe is stuck with snow or mud.
● Whether the surface of the radar
probe is frozen.
● Whether parked the vehicle in hot
or cold weather for a long period.
If all above items are excluded, please
deliver your vehicle to Chery
authorized service station for checking
and repair.
●
Please notice the following conditions, of
which the radar probe may not alarm even
closing to the obstacles.
●
The radar probe may
not function below -20
℃ or above 50℃.
●
The short objects such as rock.
●
The soft objects that easily absorb
the ultrasonic wave such as snow,
cotton or sponge.
●
When the splashed water is frozen
on the surface of the radar probe.
●
When the radar probe is stuck
with snow or mud that covered the
backup radar probe.
The thin objects such as steel wire,
rope, wire net.
29
Interior Device Operation and Adjustment
It will not alarm the obstacles out of
the detection scope.
When having several
obstacles, the backup
radar probe will only alarm the
obstacle with nearest distance.
During the vehicle movement,
please notice that the backup radar
probe at another side may
approach to other obstacles.
Please notice the following conditions,
which may result the wrong detection
alarm.
● The thin objects such as steel wire,
rope, wire net.
● When using the equipped high
output wireless or antenna.
●
When driving in the jelly rain or
snow.
● When encountered the horn of
other vehicles, the engine sound of the
motorcycle, and the approach of the
objects with the issuance of pneumatic
braking sound.
30
Interior Device Operation and Adjustment
●
For the objects that hardly reflect
the ultrasonic (as shown in figure
below), it may not alarm
depending on the shape of the
obstacle.
Pillar
柱
Thin
细tree
的树
Corrugated
瓦 楞 纸
paper
Bicycle
自 行 车tire
胎
角材
Corner
material
基
石 stone
Base
Front Passenger
Bag (PAB) Switch
Air
It’s not allowed to take child at the
front row passenger seat since the
blown-out of the air bag will cause
certain injury to the child. Therefore,
it’s recommended not to place the child
at the front row passenger seat when
taking the vehicle. Please operate in
accordance with the following items
when it’s must to place the child at the
front row passenger seat.
Open the glove box before driving,
plug one half of the key into the hole of
the front row passenger air bag (PAB)
and rotate clockwise to ON position,
which indicates that the passenger side
air bag circuit is connected and will
blow when certain conditions are met;
when rotate counter-clockwise to OFF
position, it indicates that the passenger
side air bag is turned off and will not
blow.
In order to remind the driver of the
ON/OFF status of the driver/passenger
air bag switch before driving, the
instrument is equipped with PAB
working indicator lamp, which will
light to remind the driver of noticing
the position of the PAB switch when
the ignition switch is turned on.
31
Driving
Chapter 3
Driving
33
Driving
compartment and the exhaust pipe that
may cause fire.
Driving
Start
Preparation before Start
The engine start is controlled by the
engine electrical control system.
Do not step the accelerator before start
and during start when start the
electrical injection engine. The
accelerator should be used only when
having difficult start. Please refer to the
section “Engine Start” for the details of
vehicle start.
The long period high speed
idling running of the engine
will result the overheating of
the engine and the exhaust system,
which may result the danger of fire or
other damages. Therefore, do not park,
idling run or driving on the ground
covered with dry grass and other dry
coverings. The exhaust system will
increase the temperature of the engine
Do not start the vehicle in the
closed garage or other closed
locations since the vehicle
exhaust gas is poisonous. Make sure to
open the garage gate before the engine
start. Refer to the section “Caution of
Vehicle Exhaust Fume” for details.
Safety Notice
The idle speed of the engine is
controlled by the electrical control
system. The idle speed at engine start is
relevant high to help increase the
engine temperature. The idle speed
should reduce automatically when the
engine temperature is increased. Please
deliver your vehicle to the Chery
authorized service station for overhaul
if the idle speed can’t reduce
automatically. Do not run the engine at
the speed higher than specified idle
speed for more than 10 min.
Before Vehicle Start
1.
Make sure all passengers are
fastened with safety belt. Please
refer to the chapter "Seat and
Safety Protection Device” for the
details of safety belt and its
correct operation method.
2.
Make sure the front head lamp
and other electrical fittings are
turned off.
3.
Make sure
handbrake.
4.
Make sure that the gear selector
lever is at neutral gear or parking
gear.
5.
Switch the ignition switch to
(ON), but not to (START).
to
lift
up
the
If the rotation of the key needs great
effort, it may rotate the steering around,
till the key can rotate freely. The
occurrence of such condition may have
following causes:
y
Deflection of front wheel.
y
The front wheel touched with the
road curb.
34
Driving
y
The steering wheel is rotated
during get-on and get-off
(self-lock of the steering wheel).
6.
At the same time when the
ignition key is turned on, make
sure that the dashboard alarm
lamp lights shortly. If negative,
then it needs to deliver your
vehicle to the Chery authorized
service station for overhaul.
the first start. Instead, it should
rotate the key to the OFF position
and wait for 10 s before retry.
3.
If the driver safety belt is fastened
before turn on the ignition key, then the
safety belt alarm lamp won’t light.
Engine Start
1.
2.
Rotate the ignition switch to the
START position but not step
down the accelerator (if equipped
with automatic transmission,
make sure to confirm that the
gearshift lever is at P or N gear
before start), release the key after
the engine start, and the key will
return to ON position.
IF the temperature is higher than
-12° C, then the engine should
not be started within 5 s during
IF the temperature is lower than
-12° C, then the engine should
not be started within 15 s during
the first start. Instead, it should
rotate the key to the OFF position
and wait for 10 s before retry. If
the two consecutive starts all fails,
then step the accelerator to the
end and hold before rotate the
key to the START position. After
the engine start, release the key
and release the accelerator pedal
slowly following the increasing
of the engine speed.
4.
After the engine start, run at idle
speed for several seconds, step
down the clutch, shift to the drive
gear, release the handbrake and
prepare the driving.
5.
The
normal
environment
temperature condition of the
engine start is -25℃~40℃ (it
may present other abnormal
conditions when the environment
temperate is out of such scope).
Caution of Vehicle
Exhaust Fume
In despite of without color or smell, the
vehicle exhaust fume contains the
carbon monoxide, of which the danger
must be cautioned. The certain contents
in the engine exhaust gas and the
certain chemicals contained or emitted
by certain vehicle components may
result the carcinogen, the defect of the
new born or other damage of the
genital system.
If smelled the fume
peculiar smell within the
vehicle, please deliver your
vehicle to the Chery
authorized service station for
overhaul immediately. Do not
continue to drive. The exhaust fume is
one poisonous substance that may
endanger the life.
The exhaust system and the vehicle
ventilation system should be checked
under following conditions:
y
When the vehicle is lifted for
overhaul.
35
Driving
y
When the sound of exhaust
system is changed.
Engine Speed Limit
y
When the vehicle is damage due
to the collision.
The engine speed is limited by the
electrical control unit (ECU) so as to
protect the engine.
Ventilation Notice
When the vehicle is parked in the open
field for long period idle or when the
persons rest in the vehicle, the window
should be opened for at lease 2.5 cm.
Or open the A/C system ventilation
function to let the fresh air into the
vehicle.
通风口
Engine Turn-Off
Clean the snow, leaf fall or
other foreign articles that
stocked in the air inlet so
as to improve the vehicle ventilation
capability.
Engine Control System
Adaptive Function
Release the accelerator pedal. Wait the
engine to lower to idle speed and then
turn off the ignition switch.
If the battery cable is once removed
from the battery before refit, then the
vehicle may present some abnormal
evidences during the initial period of
the driving. This is the engine control
system is re-learn to adapt to the engine,
which belongs to normal condition.
Please do not step down the
accelerator pedal before
turn off the engine.
After long period high speed driving,
do not turn off the engine immediately
after parking. Run the engine at the
speed higher than idle speed for two
36
Driving
more minutes so as to lower the engine
temperature gradually.
Turn off the ignition switch, the
temperature will still be
very high after the turn-off
of the engine and the
radiator electrical cooling fan will still
keep running. Even the cooling fan
stops running, it may run suddenly
again due to excessive high
temperature. Therefore, cautions
should be taken when working near
the engine so as to avoid the scalding.
In case of the failure of one
brake circuit, it will needs
more force to step down
the brake pedal and the stop distance
will be lengthened. In case of the
occurrence of such condition, please
deliver your vehicle to the Chery
authorized service station for
overhaul before you continue your
journey.
Operation Instruction of
Brake System
If the brake system alarm lamp doesn’t
turn off upon the release of the
handbrake, it indicates that the brake
system has trouble or the brake liquid
level is too low.
Dual-Circuit Brake System
vehicle
vehicle to the Chery authorized
service station for the checking of the
brake system.
Brake Liquid
Brake
Your
dual-corner dual-circuit brake system.
The remaining circuit will still keep
effective operation even if one circuit
has fault.
is
equipped
with
The brake liquid level should be
checked periodically in accordance
with the requirements.
Please refill with brake
liquid
immediately
to
maintain the liquid level at
MAX marking and deliver your
It’s quite normal if the brake system
issues noise occasionally. The long
period grinding or screaming noise
between the metal and the metal may
indicate that the brake disc was
severely worn out and should be
replaced. At that time, please deliver
your vehicle to the Chery authorized
service station for overhaul.
If there have consecutive shake or
shock transmitted to the steering wheel
during braking, please deliver your
vehicle to Chery authorized service
station for overhaul immediately.
The new brake lining can achieve best
brake effects only after run in. The
brake effects may be slightly lowered
within the initial 200 km. Under such
condition, the brake effects can be
compensated by enhancing the proper
force on the pedal. This essential point
also applies to the new brake lining
37
Driving
after replacement.
The worn-out status of the brake lining
depends on the working condition and
driving method to large extent. For the
vehicles mainly for city transportation,
the working condition of the brake
lining is relatively poor due to the
frequent start and stop. Therefore,
make sure to deliver your vehicle to the
Chery authorized service station for the
checking of brake lining thickness or
the replacement of brake lining in
accordance with the maintenance
mileage specified in the Maintenance.
For downward slope driving, it should
shift to low gear at proper time so as to
sufficiently take advantage of the brake
effects of the engine and reduce the
load of brake system. At that moment,
the brake pedal should be stepped
down all the time even the braking is
required.
The moisture brake disc will reduce the
brake efficiency. After paddling, heavy
rain or car wash, it should step down
the brake pedal slightly to generate
friction heat between the brake disc and
the brake lining so as to evaporate the
water and resume brake effects.
If the vehicle is equipped
with front boiler, it should
ensure the free airflow to the front
brake; otherwise the brake system may
overheats due to poor heat radiation to
reduce the brake effects.
Brake Booster:
If the brake booster can’t function
because the vehicle is trailed or due to
its own fault, then it needs to enhance
the stepping force to compensate the
boosting effects of the booster.
Therefore, it’s preferable not to place
the foot cushion or other covering on
the floor around the pedal. If really
needed, then make sure that the
placement of foot cushion won’t
obstruct the pedal movement without
any sliding.
All pedals should be
stepped down to the
end and should fully
return
with
free
The brake booster is subject to the
control of engine vacuum
booster. This device will act
only when the engine is
running. Therefore, do not turn off the
engine for sliding when driving on
downward slopes.
Anti-lock
(ABS)
Brake
System
The anti-lock brake system can avoid
the lock of the wheels that can keep the
steering performance of the vehicle
even under emergent braking so as to
escape the obstacles.
Reaction of ABS
38
Driving
The anti-lock brake system will not
effect under normal brake period and
will effect only when the wheels are
almost locked. During braking, the
pulse movement of the brake pedal
together with the noise indicates that
the ABS is under working. Such pulse
movement and noise are normal. At
such moment, do not release the pedal.
Braking Taking Advantage of
ABS
The consecutive stepping down of the
brake pedal with full force under
emergent condition will actuate the
antilock brake system immediately to
keep the control of steering. If with
enough space, you still can escape the
obstacles.
It’s recommended that you should get
familiar with this brake technology
firstly; however, any unnecessary
adventures should be avoided.
Though ABS can ensure
the best brake effects,,
the stop distance will
have great difference depending
on the road conditions. The ABS
can’t always make sure to reduce
the braking distance, such as on
sand or snow ground, the braking
distance of the vehicle with ABS
may be much longer than the one
of the vehicle without ABS. Also,
taking advantage of ABS can’t
eliminate the dangers arising
from the excessive short distance
with foregoing vehicle, paddling,
excessive fast turn or poor road as
well as avoid the accidents arising
from the careless and incorrect
driving. Please drive carefully and
decelerate the driving at turns.
which should be noticed during
driving. Please contact with Chery
authorized service station timely to
repair the ABS system.
ABS Self-Examination
The
ABS
will
conduct
the
self-examination after the vehicle start.
The mechanical noise can be heard
during this period, which is quite
normal.
The lighting of ABS alarm
lamp during driving indicates
the fault in the ABS system,
at that moment the mechanical system
can function the normal brake effects,
39
Driving
Important Principle of
Taking Advantage of
ABS for Braking.
Handbrake
handbrake much easier.
Operation of Automatic
Transmission ( )
The automatic transmission in your
vehicle is one kind of electrical
controlled four-speed transmission with
automatic gearshift mode.
1.Step down brake
pedal and hold with
full efforts.
Pull up the handbrake handle after
parking so as to avoid the humping due
to temporary carelessness.
The parking brake lamp will light when
applied with handbrake under the
condition that the ignition switch is
turned on.
Pull up the handbrake lever when to
use handbrake.
2. Rotate the steering
wheel to round the
obstacle.
You
can
maintain the turn control
capability no mater how
violent the braking is.
When to release the handbrake, pull up
the handbrake lever slightly, push down
the release button at the end of the
handle and push downward.
The handbrake is applied on the rear
wheels. It can step down the brake
pedal at the same time the handbrake is
pulled up so that it can pull up the
40
Driving
Gear Selector Lever Position
41
Driving
Make sure to pull up the
handbrake
handle
before
leaving the vehicle.
P = Parking
R = Reverse Gear
SHIFT
Lock
LOCK
=
Gearshift
When to move the gearshift lever
without the stepping down of the brake
pedal, please push down SHIFT LOCK
(gearshift lock) key.
N = Neutral Gear
D = Drive Gear
R = Reverse Gear
+ = Upshift
This position must be shifted to during
backup.
- = Downshift
This position can be shifted to
only when the vehicle is
completely still.
P = Parking
Under such position, the output shaft of
the transmission is locked and drive
wheel can’t rotate.
The gear selector lever can move out
from such parking position only when
the brake pedal is stepped down and
the ignition switch key is at ON
position.
When need to use gear R,
please shift gear R position
after
the
vehicle
is
completely still; otherwise it may
damage the transmission. Chery
Automobile Co., Ltd. will not be
liable for the warranty of such
malfunctions.
N = Neutral Gear
Such position can be shifted to only
when at engine start or idle speed. At
such time, no power will be transmitted
to the drive wheel.
D = Drive
The gear selector lever position during
automatic driving.
Manual Gearshift Mode
+ = Upshift
- = Downshift
The gear selector lever shift
position under manual drive
mode.
Operation Notices:
1. The engine can start only when the
transmission is at “P” or “N” position.
2. The manual gearshift mode can only
be shifted to when the gear selector
lever is at position D.
3. When to shift to manual gearshift
mode, please shift the gearshift lever
rightward to position; It will be
automatic gearshift mode if the
gearshift lever is always at left.
4. Under the manual gearshift mode,
shift the gear selector lever towards +
mark to upshift the transmission to the
next high gear; shift the gear selector
lever towards – mark to downshift the
transmission to the next low gear.
42
Driving
5. Under manual gearshift mode, the
selected gear can be accepted only
when the gearshift request conforms
with the requirements of the
transmission controller.
6. The braking no matter under manual
gearshift mode or the automatic
gearshift mode can achieve the
automatic gearshift function without
any gearshift operation;
7. The gear selector lever at “N” or “P”
position during driving is strictly
prohibited; otherwise the transmission
will be damaged, for that Chery
Automobile Co., Ltd. will not be liable
for warranty.
8. In order to avoid the mis-operation
of the gearshift lever, please check if
the operating lever is shifted to the
correct position; After operation, make
sure to check the position of gear
selector lever by means of the
instrument display.
Gear Selector Lever Lock
brake
pedal,
disregarding
the
push-down of the stop button on the
gearshift lever handle; It’s unnecessary
to push down the stop button when
shift the gearshift lever within other
positions.
Gear Display
Stop Button
When the ignition switch is turned on,
the gear selector lever position will be
displayed on the central screen of the
dashboard.
The display of various gears is shown
in following figures:
Display of P Position:
When to shift the gearshift lever from
“P” to “R”, from “N” to “R”, or from
“R” to “P”, make sure to step down the
brake and push down the stop button
(shown in above figure) on the
gearshift lever handle to relieve the
gearshift lever lock. When to shift from
“N” to “D”, make sure to step down the
43
Driving
Display of R Position:
Forced Downshift (Kick Down)
Start
Display of N Position:
Display of D Position:
Display of Manual Mode:
Under manual gearshift mode, the
selected gear by the driver will be
displayed in digit type in the display
screen. The figure takes gear 2 for
instance.
Keep the engine at idle speed, step
down the brake pedal, move the
gearshift lever to drive gear, release the
brake pedal slowly, at the same time
step down the accelerator pedal slightly
and the vehicle will start drive slowly.
Under special conditions (such as on
the road covered with snow and ice), it
may select gear 2 under manual
gearshift mode as the start gear.
The vehicles with automatic
transmission can’t be started
by trailing or pulling the
vehicles. Please conduct jumper start
by means of connecting the jumper
cable to the support battery.
This automatic transmission has
internal nominal Kick Down mode.
When on upward abrupt slopes or at
overdrive, the transmission will shift to
low speed gear from high speed gear
automatically by stepping down and
holding the accelerator pedal to the end
at gear D so as to achieve the require
great torque.
The vehicle will shock slightly at the
same time when at forced downshift for
acceleration, which is the effects of
forced downshift instead of the engine
acceleration tremble. All above are
related to the rapid stepping down of
accelerator, which are the important
driving essentials the driver must
master.
It’s difficult to downshift for
acceleration if stepping down the
accelerator slowly. If stepping down
the accelerator to the half or two third
of stroke, it’s impossible to obtain
sufficient acceleration horsepower
(torque), even though it can obtain the
increasing of some horsepower (torque).
That’s the cause why the customers
44
Driving
complained low horsepower (torque)
during driving. In addition, when
stepping down the accelerator slowly
for acceleration, the engine tremble
will even get bigger. Therefore, it
should be avoided.
Midway Stop
When encountered with the red light or
any other conditions that required the
temporary stop, release the accelerator
pedal and step down the brake pedal,
with the gear selector lever remained at
current position. When start again,
release the brake pedal and step down
the accelerator pedal.
Driving Essentials on Various
Road Conditions
It’s recommended to use gear D and
step down the accelerator to the end
rapidly to obtain better acceleration
performance on the flat roads with
small gradient.
It’s recommended to use gear 3 or gear
2 under manual gearshift mode and
step down the accelerator pedal rapidly
to
obtain
better
acceleration
performance on the roads with medium
gradient.
It’s recommended to use gear 1 or gear
2 under manual gearshift mode instead
of gear D and step down the accelerator
pedal rapidly to obtain better
acceleration performance on the roads
with large gradient.
On downward slopes, the overlong
persistent braking period will result the
weakening of the brake performance
due to overheating. At that moment, the
engine brake should be sufficiently
utilized to reduce the vehicle speed.
The engine brake is the braking effects
achieved by means of the low gear
speed ratio of the engine deceleration
and transmission in such manner of
shifting the transmission to low gear
and releasing the accelerator pedal
during journey. The lower the gear is,
the better the engine braking effects are.
It’s recommended to use gear 2 or gear
1 under manual gearshift mode on the
downward slopes with extreme large
gradient or length.
For the downward slopes with extreme
large gradient, in order to obtain the
bigger braking effects, please use
manual gearshift mode and shift to
lowest gear before downward slopes.
If the drive wheel is entrapped in the
mud or the snow, try to shake the
vehicle by repeated forward/backup.
Shift the gear selector lever between
“D” and “R” repeatedly and step down
the accelerator pedal slightly. In order
to enhance the effects, it may shift to
“R” when the vehicle is still moving
forward and vice versa. The long
period gearshift (shaking) between
forward and backup should be avoided,
which will result the excessive
worn-out of the transmission. The
shaking period should not exceed one
minute. Try to keep the engine at low
speed as far as possible during shaking.
During the high speed
vehicle
driving,
the
gearshift to the low gear
will result the great impact to the
engine and the transmission that will
result the damage of the engine and
the transmission. The low gear should
be shifted to only when the vehicle
speed is lowered to the speed
45
Driving
allowable for downshift.
y
Operation of Automatic
Transmission ( )
Use/Operation Method and Notices:
y
y
y
y
During gearshift, fully step down
the clutch pedal to release the
driver from the engine torque and
then operate the gearshift lever
for gearshift rapidly.
The low speed gear should be
used for downward slopes and
turns. The slide with disengaged
clutch is not allowed.
When shift the transmission from
low gear to high gear, do not
conduct gear skip operation;
otherwise the service life of the
synchronizer will be affected.
The forced gearshift by means of
synchronizer to start the engine
under neutral gear and engine
flameout status is strictly
prohibited; otherwise the service
life of the synchronizer will be
y
y
affected.
steering system:
The flap method (namely the
operation method of one pulling
and one releasing) is strictly
prohibited
during
gearshift.
Please
always
hold
the
transmission lever with hand so
as to greatly reduce the slide and
friction time and the worn-out of
the synchronizer lock ring.
y
The time when rotating the
steering wheel to the end (to left
dead point and right dead point)
should not exceed 10 s during
engine running.
y
When the power steering liquid in
the power steering liquid reservoir
is lower than MIN mark, please
refill with power steering liquid
immediately. Do not drive the
vehicle before refill.
Do not leave your hand on the
gear selector lever during driving;
otherwise it will result the early
worn-out of the gearshift fork.
In case of the detection of any
abnormal evidences such as
abnormal
noise
of
the
transmission or the obvious
heavier operation during use,
please stop the vehicle for
inspection
immediately
and
continue the driving once the
trouble is resolved.
Steering
In order to avoid the damage of power
In case of trouble of power steering
system or the turn-off of the engine, the
vehicle will lose the steering boost. You
still can rotate the steering wheel,
provided with great strength.
In case of vehicle deflection or tremble
during the driving, please check the
following items:
y
Whether the tire pressure is
insufficient.
y
Whether the tire is worn evenly.
y
Whether
the
suspension
components is loosened or worn
out.
46
Driving
y
Whether the steering components
is loosened or worn out.
y
Whether the wheel alignment is
correct.
Paddling
If it’s must to paddle during journey,
make sure to drive slowly and carefully,
especially when having no knowledge
of the water conditions. Do not drive
forward further if the water can
submerge the wheel hub.
During paddling, the traction force and
the brake performance of the vehicle
will be lowered and the vehicle will
have the danger of flameout.
In case of the water ingress into the
intake pipe of the engine, it will cause
the serious damage of the engine. The
deeper paddling will result the water
ingress into the transmission through
the transmission air vent, which will
result the damage of the transmission.
water from the brake. The water on the
brake
will
lower
the
brake
performance.
Three-Way
Converter
Unleaded Gasoline
Catalytic
The catalytic converter will help reduce
the pollution of exhaust gas.
Make sure to use unleaded
fuel. The leaded fuel will
result
the
permanent
damage of the catalytic converter
and the oxygen sensor. Chery
Automobile Co., Ltd. will not be
liable for any damages arisen from
the use of leaded fuel. Such
damages are excluded from the
warranty scope. If you refill with
leaded fuel accidentally, please
contact with the nearest Chery
authorized service station.
The vehicles with gasoline engine are
equipped with narrow refill opening
that only accommodates the unleaded
gasoline pump refuelling gun nozzle.
During the running of the
gasoline
engine,
it’s
absolutely not allowable to
pull out the high voltage line of the
ignition coil. Check if the engine
functions normally by means of
cylinder flameout method or observe
the jump spark condition of the spark
plug; otherwise the three-way
catalytic converter will be damaged.
After paddling, make sure to drive
slowly and step down the brake pedal
slightly for several times to remove the
47
Driving
Notice:
the engine.
Chassis Protection
The three-way catalytic converter will
be getting very hot if the engine is
under continuous running, therefore,
notice to wear the protective glove
during repair so as to avoid the
scalding.
y
Run the engine under the
condition that one spark plug
cable terminal is removed.
y
Start the vehicle with the engine
still at working temperature by
means of pulling or hauling.
Your vehicle is equipped with heat
insulation plate. Do not apply the paint
on the body of heat insulation plate,
exhaust pipe or catalytic converter or
the surrounding areas. Do not
disassemble the heat insulation plate.
Drive the Vehicle Equipped
with Catalytic Converter
y
Turn off the ignition switch
during driving.
Fuel Consumption
Please avoid the condition that will
result the ingress of the un-combusted
or partial un-combusted fuels into the
catalytic converter, especially when the
engine is at high temperature.
The following conditions should
be avoided:
y
Run out of fuel.
y
Unnecessary long period start of
Parking
Do not park, idle or drive the vehicle
on the dry leaves or grass. Even the
engine is turned off, the exhaust within
short period will continue the radiation
of equivalent heat, and therefore, it still
has potential fire danger.
Make sure to turn off the ignition
switch before leaving the vehicle. Do
not run the engine when no one in the
vehicle. The negligence of this point
may result the accident movement of
the vehicle, which will result the body
injury or property damage.
The fuel consumption is
influenced by following
factors:
Selection of Vehicle Speed or
Gear
Fuel consumption
In case of the evidence of
poor engine ignition or the
lowered performance during
driving, please drive at low speed to
the nearest Chery authorized service
station. Do not drive at large
accelerator.
Vehicle speed
48
Driving
The above figure illustrates
how the fuel consumption is
influenced by the selection of
vehicle speed and gear. Maintaining at
low gear to improve the acceleration
performance will result the obvious
higher fuel consumption.
Stroke
Temperature
Distance/Engine
The frequent cold vehicle start and the
short distance journeys will result the
obvious increasing of the fuel
consumption.
Traffic and Road Condition
The crowded traffic, upward slopes,
multi curved routines and rough roads
will cause detrimental influence on the
fuel consumption.
consumption but also reduce
wearing and noise of the brake.
the
It’s recommended to turn off
the engine during traffic jam
or long period waiting such
as red light.
The 3 min engine idle is equivalent to
driving for 1 km.
vehicle.
y
Use the accelerator smoothly.
y
Shift to next higher gear as soon
as possible so as to achieve lower
engine speed.
y
Prediction of traffic condition.
y
Turn off A/C and rear windscreen
heating immediately whenever
unnecessary.
y
Check/adjust the tire pressure
periodically.
y
Conduct vehicle maintenance
periodically, preferable conducted
by Chery authorized service
station.
Vehicle Load Status
The increasing of vehicle load will
result the higher fuel consumption.
Vehicle Technical Status
The low tire pressure or improper
engine and vehicle maintenance also
will result higher fuel consumption.
Essentials for Fuel- Saving
Driving and Environmental
Protection:
Good Driving Habits
y
The prediction of danger and keeping
safe driving distance with foregoing
vehicle will not only reduce the fuel
Fuel-saving driving, and use
supplementary electrical loads
only when needed.
y
Start without the heating of the
Radiator Fan
The radiator fan is of electrical fan with
the working condition is controlled by
the engine ECU. This switch will
automatically turn on the fan circuit
when the coolant or the engine
compartment
reached
certain
temperature.
49
Driving
After stop the vehicle and
the engine, the radiator fan
will continue running for
certain period since the engine is still
under hot condition and will stop
running when the engine is cooled to
certain temperature. Even though, the
fan may still start suddenly in case of
the sudden temperature increasing of
the engine compartment due to the
influence
of
the
ambient
environmental temperature (sunshine
exposure or high temperature region).
Therefore, cautions should be taken
when operate in the engine
compartment so as to avoid the
accident.
and the vehicle speed has no obvious
reduction on upward slopes.
Instruction:
If the fan isn’t running when the
coolant temperature reached the fan
start temperature, then check the fan
fuse for burn-out. Replace the fuse if
necessary.
The fan speed is independent of the
engine speed and the gearshift to low
gear will not promote the cooling
effects of the fan. Therefore, it’s
unnecessary to shift to low gear
provide that the engine runs smoothly
50
Instrument Panel
Chapter 4
Instrument Panel
51
Instrument Panel
Instrument
Cigar Lighter
Horn switch
Wiper switch Instrument
Audio system
A/C vent
Steering wheel
Panel
Head Lamp Switch
Dimmer
control
switch
Adjustment switch
of
electrical
regulated head lamp
Coin box
Air bag identification
Front Fog Light Switch
Front compartment cover pull-up switch
Glove box
A/C system
Ashtray
Rear Fog Light Switch
Danger Alarm Lamp Switch
Heating of rear windscreen
52
Instrument Panel
Instrument (
Coolant
temperature
normal indicator lamp
)
Door Ajar indicator
Rear fog light
Position lamp Front fog light lamp
Brake system trouble alarm lamp
Right turn indicator lamp
High
beam
indicator lamp
Left turn indicator lamp
Engine trouble alarm lamp Maintenance
EPC trouble alarm lamp
reminding lamp
ABS alarm lamp
Coolant
temperature
high alarm lamp
Parking indicator lamp
Fuel gau
Air bag alarm lamp
Speedometer
Gear display
53
Low fuel level alarm lamp
Instrument Panel
related system if certain alarm lamp does
When the ignition switch is turned on,
not light or certain alarm lamp lights or
this lamp will light shortly and at the
flashes persistently after the engine is
same time the ABS system will perform
started.
self-examination to determine if the
system is capable of normal operation. It
indicates that the ABS system has trouble
Low Fuel Level Alarm Lamp
if this lamp lights persistently or flashes
when the ignition switch is turned on or
Alarm Device
when during driving. However, the
The alarm device is used to indicate the
vehicle still has conventional brake
running status of the driver’s vehicle and
capability (without ABS), unless the
whether the vehicle presents any problem
When the fuel volume in the fuel tank is
that will result severe damage or injury.
less than 10 L, this lamp will light for
If certain system function of the vehicle
alarm and the fuel gage indicator will
has fault, the corresponding alarm lamp
point to the red alarm line.
will light or flash.
When the ignition switch is turned on,
deliver
the
vehicle
to
the
Chery
Under such case, please deliver the
vehicle to the Chery authorized service
station for overhaul as soon as possible.
However, please drive carefully and
Please refill the fuel as soon as possible
avoid high speed driving. Please refer to
when the alarm lamp lights.
the “Brake” section for the important
most alarm lamps will light shortly to
conduct system self-examination. Please
brake system alarm lamp is lighting.
ABS Alarm Lamp
notices related to the ABS system
operation.
authorized service station to overhaul
54
Instrument Panel
Parking Brake Alarm Lamp
send to the Chery authorized service
station for checking.
This lamp will take effect when the
ignition switch is turned on.
This lamp will keep light when the
handbrake is pulled.
Brake System Alarm Lamp
This lamp will take effect when the
The lighting of brake system
alarm lamp during the
driving indicates the trouble
in one line of the dual brake circuits. In
such case, please drive carefully to the
nearest Chery authorized service
station and ask for the professional
personnel
for
overhaul.
In
consideration
of
the
severe
deterioration of the brake performance
and the lengthened brake distance,
please keep more distance from the
forgoing vehicle during the driving and
enhance the pedal pressure accordingly
during the braking.
Parking/Position
Lamp
Indicator
This indicator lamp will light when the
position lamp is turned on.
Seat Safety Belt Reminder
Lamp
If the ABS alarm lamp and brake
This alarm lamp will light to remind the
system alarm lamp light persistently
driver to fasten the safety belt if the
at the same time, stop the vehicle
driver safety belt is not fastened under
immediately on the premise of
the condition that the ignition switch is
Please check if the brake liquid level is
ensuring the safety. Before continue
turned on.
too low when this lamp lights. When the
your journey, please deliver the
liquid level is low, please immediately
vehicle to the Chery authorized
refill with the brake liquid to between
service station to check the brake
MIN marking and MAX marking and
system.
ignition switch is turned on. This lamp
will light when the brake system has
trouble or the brake liquid level is low.
Engine Trouble Alarm Lamp
55
Instrument Panel
When the ignition switch is turned on,
Turn Signal Indicator Lamp
Air Bag Alarm Lamp (
)
this alarm lamp will light and the engine
electrical
control
system
is
under
self-examination status. The alarm lamp
will turn off within 6 s if such system has
Comprised of left turn signal indicator
lamp and right turn signal indicator lamp.
When the ignition switch is turned on,
At the same time when the left turn lamp
the trouble alarm lamp will light 3-4 s
or right turn lamp is turned on, the
before turn-off, which indicates that the
The lighting of this alarm lamp during
corresponding turn signal indicator lamp
safety air bag system functions normally.
driving indicates the trouble of engine
will flash accordingly (relevant slow).
It indicates that there has trouble code if
electrical control system. Please deliver
The left/right turn lamps and left/right
the trouble alarm lamp lights persistently.
the vehicle to the Chery authorized
turn signal indicator lamps will flash at
service station for overhaul as soon as
It indicates the trouble if this lamp lights
the same time when the danger flashing
possible.
during the driving. Please deliver the
alarm lamp is turned on.
vehicle to the Chery authorized service
High Beam Indicator Lamp
It indicates the trouble of corresponding
station for the checking of this system.
no trouble. The engine must be checked
if the alarm lamp lights persistently.
turn lamp if the flashing frequency of the
turn signal indicator lamp is increased
two times.
This lamp will light when using the high
Low Engine Oil Pressure
Alarm Lamp
beam lamp or when the front head lamp
is flashing.
56
Instrument Panel
When the ignition switch is turned on,
Generator Alarm Lamp
this indicator lamp will light before
turn-off 3 s later.
If this lamp does not turn off 3 s later or
This alarm lamp will light when the
this lamp lights during the driving, please
ignition switch is turned on and will turn
stop the vehicle immediately, stop the
off when the engine is started.
engine and check the engine oil level.
Temperature
Alarm (Red
After the ignition switch is turned on,
If this lamp does not turn off or this lamp
The indicator lamp will flash for alarm
lights during driving, please stop the
when the engine oil is less than 0.3 Bar
vehicle immediately, stop the engine and
and the engine speed is less than 300
check the generator belt.
rpm.
Coolant
Overheating
Indicator)
this lamp will light before turn-off
several seconds later. If this lamp does
not turn off several seconds later, or this
lamp flashes together with buzzer alarm
due to overheat coolant temperature or
If the generator belt is normal, then
low coolant level during driving, then
The indicator lamp will flash for alarm
continue to drive to the nearest Chery
make sure to stop the vehicle, stop the
when the engine oil is less than 0.3 Bar
authorized service station for overhaul;
engine, check the coolant level, and refill
and the engine speed is less than 300
however,
with the coolant in accordance with the
rpm.
devices (including A/C) should be turned
Please refill with oil immediately if the
oil lever is too low.
Please deliver the vehicle to
the
Chery
authorized
service station for checking
if the engine oil consumption is too
fast.
all
unnecessary
electrical
off since the battery will discharge
persistently during driving.
If the generator belt is damaged, then do
not continue to drive the vehicle. Make
sure to ask for professional personnel for
overhaul.
regulations.
Scalding Caution!
The cooling system is under
high temperature and high
pressure status when the engine is hot.
Therefore, make sure to open the
radiator cover after the engine is
cooled. Do not touch the radiator
fan!
57
Instrument Panel
Door Ajar indicator Lamp
self-examination on the electrical throttle.
the user to perform entire vehicle care
The alarm lamp will turn off if such
and maintenance in the service station.
system has no trouble. The electrical
throttle must be checked if the alarm
Located in the centre of instrument
central clock display screen. When the
ignition switch is turned on, this lamp
will light if whichever one of the four
doors is not closed properly.
lamp lights persistently.
Such alarm symbol can be cleared
manually
at
the
finish
of
the
maintenance.
The lighting of this alarm lamp during
driving indicates the trouble of engine
electrical throttle. Please deliver the
vehicle to the Chery authorized service
Engine Coolant Temperature
Normal Indicator Lamp
(Green Indicator)
station for overhaul as soon as possible.
Electrical Throttle Trouble
Maintenance
Indicator
When the ignition switch is turned on,
this lamp will keep lighting status that
Alarm Lamp
Lamp
indicates the normal engine coolant
temperature, and will turn off till the
coolant temperature is overheating. If
this lamp does not turn on, please stop
the vehicle immediately, stop the engine,
check
the
coolant
for
overheating
When the ignition switch is turned on,
When the odometer mileage reached the
temperature or low coolant level, and
this alarm lamp will light and the engine
preset mileage setting (5,000 km), this
refill with coolant in accordance with the
electrical control system will perform
alarm indicator lamp will light to remind
regulations.
58
Instrument Panel
Passenger
Side
Air
Bag
Speedometer
Indicator Lamp
Standard fuel tank capacity: 61 L
PAB
When the pointer reached the fuel empty
When the ignition switch is turned on,
this lamp will light to remind the driver
position “E” (as pointed by the arrow),
the fuel tank has approximate 10 L fuel.
to notice the switch position of the
The pointer will move from full position
passenger side air bag. If the passenger
“F” after the vehicle with fully filled fuel
side air bag switch is at ON position,
drives for certain distance.
then this lamp will turn off within 4-5 s
During the refuelling, the fuel volume
after the ignition switch is turned on. If
that capable of refuelling will be lower
the passenger side air bag is at OFF
than the nominal capacity since the fuel
position, then this lamp will keep lighting
tank has residue fuel.
after the ignition switch is turned on.
Fuel Gauge
To indicate the current vehicle speed.
If the low fuel lever alarm lamp lights,
please refill with fuel as soon as possible.
Refer to “Low Fuel Level Alarm Lamp”.
)
Notice:
The speedometer is affect by the tire size.
Please use Chery genuine size tires,
otherwise the speedometer will not
display the correct vehicle speed.
59
Instrument Panel
Transmission
Range
indicator, Odometer, and
Digital Clock
The adjustment method
The
switch
method
of clock is as follows:
between the clock, fuel
consumption per 100 km
Under the clock display status, the clock
can be adjusted by pressing and holding
the clock adjustment button on the
The left upper corner will display the
current transmission range .
The right upper corner will display the
clock, fuel consumption per 100 km, and
the trip odometer (switchable). The clock
time can be displayed by means of two
methods: pointer type and digital type.
The right lower corner will display the
total mileage. If the vehicle is quipped
with backup radar, the left lower corner
will display the distance between the
speedometer. Press the adjustment button
and the trip odometer is
as follows:
to adjust when the hour display is
flashing. At the finish of hour adjustment,
When the ignition switch is at ON, it can
the minute display will flash after several
switch the display between clock, fuel
seconds. At that time, press adjustment
consumption per 100 km and the trip
button to adjust. At the finish of the
odometer
adjustment,
adjustment button on the speedometer.
it
will
exit
the
clock
adjustment status after several seconds.
by
pressing
the
clock
Under the display status of trip odometer ,
the single journey mileage can be reset
by pressing and holding the clock
adjustment button.
vehicle and the object at the rear of the
vehicle when shifted to the rear gear.
60
Instrument Panel
Tachometer
The early shift to the high gear will help
save the fuel and reduce the driving
noise.
Please shift to the next low gear
immediately in case of the detection of
unstable engine running.
Do not run the engine at high
speed during run in period.
To display the engine speed ( r/min).
The red area at the right side of the dial
indicates the max allowable speed scope
within short period under the engine
working temperature after run in period.
However, it’s recommended to shift the
gearshift operating lever to the next high
gear or remove the foot from the
accelerator pedal at the latest when the
pointer reached this area.
Notice:
61
Lamp Control
Chapter 5
Lamp Control
63
Lamp Control
Lamp Control
Headlamp High /Low
Beam Selector Switch
Please abide by related traffic regulations
when using the following illuminating
equipment.
Headlamp Switch
Under the condition that the lamp gear 2
is turned on, pull the handle towards the
console direction to shift into the high
beam lamp after passing through the
force application point. When the
headlamp high beam is turned on, the
OFF – Turn off the external lamp.
Gear 1
will light the parking
lamp/position lamp, the component
illuminating lamp such as instrument and
switch, and license plate lamp. At the
same time, the
instrument will light.
indicator in the
high beam indicator
in the
instrument will light. Pull the handle
towards the steering wheel direction to
return to the original position so as to
resume the low beam lamp.
Flash
of
Headlamp
When need the flash of headlamp during
the driving, it only pull the handle
towards the steering wheel direction to
the force application point and then
release the handle, which will return
position automatically. Repeat such
action
to
flash
the
headlamp
consecutively.
Front Fog Light Switch
Rear Fog Light Switch
Front
Gear 2
will light the front
headlamp (low beam or high beam).
The front fog light and the rear fog light
64
Lamp Control
are located on the central console of the
dashboard, the position between the
audio equipment control panel and A/C
control panel.
When the headlamp switch is at gear 1 or
gear 2 position, push down the front fog
light switch to turn on the front fog light,
but it can’t turn on the rear fog light
directly. It needs to turn on the front fog
light before turn on the rear fog light.
When the front fog light is turned on, the
indicator in the instrument will turn
on.
The front fog light should only be used
under the conditions that severely
affected the visibility, such as fog, snow
or rain.
When the rear fog light is turned on, the
indicator in the instrument will turn
on.
Since the rear fog light has strong
dazzling, it's allowed to use only under
the conditions with poor visibility.
Dimmer control Switch
The turn signal lamp will operate only
when the ignition switch is turned on.
Left turn signal lamp – pull the handle
downward.
Right turn signal lamp – pull the handle
upward.
When the turn signal lamp is turned on,
the turn signal indicator in the instrument
will also flash.
Buttons on Left Lower
Corner of Dashboard
During the working period of the
external lamp, it can use the light dimmer
to adjust the instrument illumination
strength. Such adjustment switch is
located near the adjustment knob of
electrical regulated headlamp on the left
lower corner of the dashboard.
Adjustment Switch of
Electrical
Regulated
Headlamp
Turn Signal Lamp
Dimmer control
仪表照明
Switch
调节开关
Electric regulated
电调大灯
headlamp
adjustment
调节开关
switch
65
Lamp Control
Press again to turn off the lamp.
The adjustment switch of electrical
regulated headlamp is located on the left
lower corner of the dashboard.
Such switch has four gears of 0, 1, 2, and
3. The adjustment of four gears can
adjust the light type of the electrical
regulated headlamp.
Interior Front Ceiling
Lamp
and
Sunroof
Switch (
)
1
Left lamp
Right lamp
Left lamp switch
Sunroof
Switch
Right lamp switch
Sunglass intake case
2
Press of left switch: The left illuminating
lamp will keep illumination. Press again
to turn off the lamp.
Press of right switch: The right
illuminating lamp will keep illumination.
Sunroof Operating Switch
The sunroof can be lifted, opened or
closed by means of the sunroof operating
switch on the ceiling lamp only when the
vehicle key is at vehicle load powered
position (namely the vehicle key is
shifted to ON position).
—
Sunroof from Open to Close
Press operating switch once to open
automatically (One-touch Open): press
and hold button ① for 0.5 s and the
sunroof will start tilt-down to open
automatically. If need to stop the sunroof
at certain position in the middle, press
the operating switch once again to finish.
Press operating switch once to close
automatically (One-touch Close): press
and hold button ② for 0.5 s and the
sunroof will close automatically. If need
to stop the sunroof at certain position in
the middle, press the operating switch
once again to finish.
—
Sunroof Anti-clip Function
(A.T.S)
The sunroof will return automatically
when subject to certain resistance force
during the sunroof movement from open
position (sunroof glass slides into the
vehicle top cover) to close position. The
anti-clip function will be actuated when
the glass is subject to certain resistance
force during the glass movement from
open position to close position, in order
to prevent the human body portions such
as head or hand or other foreign objects
from passing through the sunroof during
the sunroof movement.
Even though, nobody should protrude the
head or hand out from the sunroof during
the opening or closing of the sunroof.
!
Warning:
Do not protrude the body portion such
as head or hand out of the sunroof
when the sunroof is at open status
during the driving of the vehicle, since
at that time the sudden brake of the
vehicle will result sudden safety
accident.
—
Sunroof Tilt Up/Down
Sunroof tilt up: Under closed status of
the sunroof, press and hold the button ②
for 0.5 s and then the rear part of sunroof
glass will tilt up automatically.
Sunroof tilt down: Under opened
66
Lamp Control
status of the sunroof, press and hold the
button ① for 0.5 s and then the rear part
of sunroof glass will tilt down
automatically (till closed position).
—
Operation of Sunroof Sun
Visor
—
3
!
Notice:
▲ The sunroof can’t actuate the slide
down and the tilt up at the same
time, therefore, it can’t tilt up when
under slide down status as well as
can’t slide down when under tilt up
status. It can actuate the tilt up or
slide down after the sunroof is
closed.
▲ When the sunroof is fully opened or
close, do not continue to hold the
button, otherwise it may result the
damage of sunroof motor and the
module.
▲ Clean the dust and foreign matters
remained inside of the sunroof track
and rubber strip with water
periodically.
▲ The start of sunroof under the
condition that the sunroof glass is
frozen or covered with snow may
damage the sunroof glass and
motor.
Please contact with the Chery
authorized sales and service
station when you found
following evidences (The
evidences resulted from the
loss of initial memory of
sunroof module):
① Sunroof can’t be fully closed and
The position of sunroof sun visor is as
shown in figure 3. The sun visor will
open automatically following the sunroof
when the sunroof is opened. If needed,
please open or close manually the sun
visor when the sunroof is fully closed.
(Note: Do not close the sunroof sun visor
with force when the sunroof is opened.)
!
Notice:
Make sure to close the sun roof
properly when leaving from the
vehicle, otherwise it will leak
under raining.
▲ Wipe dry the water on the
sunroof glass before use after
the vehicle washing or raining.
The water accumulated on the
▲
opened or expanded. Some had
shaking evidence during the
movement from open position to
close position.
② The open or expansion or close of
the sunroof can reach the original
preset position.
③ The sunroof can’t conduct
one-touch open and one-touch close
functions.
④ The sunroof module can’t control
the movement of the sunroof.
67
Lamp Control
Interior
Lamp
Rear
Ceiling
Such lamp will light when the luggage
boot cover is opened (This lamp is not
subject to the control of ignition switch).
Please notice to close the luggage boot
cover securely after parking.
!
Notice: The following
operations will result the lost of
sunroof module initial memory.
During the vehicle maintenance,
such problem will present when the
battery is replaced or the power
supply is pulled out under the
condition that the sunroof not at
initial position.
▲ When plug/unplug the power
supply of the module during the
sunroof movement.
▲ When the sunroof controller failed
to resume its normal position.
▲ There are many causes that may
result the lost of module initial
memory, which are omitted herein.
▲
—
When the ignition switch is
turned off and the ignition key
is pulled out, the sunroof will
close automatically if the
sunroof is at open position.
Luggage
Boot
Illuminating Lamp
Key Hole Illuminating
Lamp
When the slide switch is at OFF position:
The illuminating lamp turns off.
When the slide switch is at ON position:
The illuminating lamp will keep
illuminating.
When the slide switch is at middle
position (door control position): The
interior lamp will light when the door is
opened and the interior lamp will keep
illuminating for 15s before turn off when
the door is closed so as to facilitate the
seating of the passengers. If the key is at
ON position, the interior lamp will light
when the door is opened and will turn off
immediately without any time lag
function when the door is closed.
The key hole illuminating lamp is
installed neighbouring the ignition key
hole. When whichever front door is
opened, the illuminating lamp will light
before turn off 6s later so as to assist the
driver to insert the ignition switch, or
such lamp will turn off when the key is
rotated to “ON” position.
Danger Flash
Lamp Switch
Alarm
68
Lamp Control
This switch is located on the instrument
central console, the position between the
audio equipment panel and A/C control
panel.
This alarm lamp should be used only
under emergent conditions so as to alarm
the following vehicles that this vehicle
has trouble or danger. Push down this
switch to turn on/turn off this system.
The danger flash lamp is operational
when the ignition switch is turned off.
The indicator on the switch will flash
after the alarm lamp is turned on. Also,
the left/right turn indicator lamps of the
combined instrument will flash at the
same time.
Brake Lamp
The brake lamp will light when the brake
pedal is stepped down and will turn off
when the brake pedal is released.
Backup Lamp
The backup lamp will light after the
ignition switch is turned and the vehicle
is shifted to reverse gear and will turn off
when the ignition switch is turned off or
the vehicle is shifted to other gear
Cosmetic Lamp
When the driver/passenger side sun visor
is lowered, this cosmetic lamp will light
once cosmetic mirror cover is opened.
69
Door Lock and Anti-Theft
Chapter 6
Door Lock and Anti-Theft
71
Door Lock and Anti-Theft
Door Lock and
Anti-Theft
Vehicle
Key
and
Remote Controller
key popup key on the remote controller.
At the complete of use, you may fold
the key back to facilitate your carrying.
Lock
Central Lock System
Unlock
move downward during lock. Also, it
can lock the door by pushing down the
safety switch.
In order to avoid the ingress
of foreign force into the
vehicle during driving,
please drive your vehicle with the
doors fully locked.
Door Lock
All doors of this vehicle can be
operated by means of the key, remote
controller or the control switch at the
driver side door trim simultaneously.
All doors can be opened or locked
outside of the driver side door by
means of the key.
The key and remote controller adopted
the integrated design that capable of
operating all locks on your vehicle. The
new key is available in Chery
authorized service station in case you
lost your key. The second key should
be kept in the safe place for emergent
need.
The key will pop up from the inside of
the remote controller by pressing the
All doors will be locked at the same
on
time when the lock button
the driver side door trim is pressed. All
doors will be unlocked at the same time
The front doors can be locked and
unlocked from outside by means of the
key. It can use the door handle to
unlock from the inside of the vehicle.
When to lock the rear doors, push
down the safety switch and close the
doors when leaving the vehicle.
However, in consideration of the safety,
it’s preferable to close the doors by
means of the remote controller.
when the unlock button
on the
driver side door trim is pressed.
The safety switch button of all doors
will move upward during unlock. The
safety switch button of all doors will
72
Door Lock and Anti-Theft
the vehicle.
Child safety lock
The doors will be locked
automatically when the
vehicle
speed
reached
35~45 km/h. Each engine start will
only have once automatic lock
function. If the central lock function
is activated or relieved when stop the
vehicle during driving, then it has no
automatic lock function when the
vehicle reached 35~45 km/h again.
The lock will be automatically
relieved after parking and engine
flameout.
Rear Door Child Safety
Lock
The upward switch of the rear door
child safety lock switch can activate the
child safety lock, in such case the door
can only be opened from the outside.
The downward switch of child safety
lock switch can cancel the child safety
lock.
The figure illustrates the unlock
position of the child safety lock. The
child safety lock will be locked when
switch the child safety lock fork
upward. Only the two rear doors have
the child safety lock.
In hot days, the vehicle interior
temperature will increase rapidly after
the engine flameout. The person or
animal may be injured or event to
death (including brain death) when
left in hot environment, even within
short period. This is extremely
dangerous to the baby and child.
Therefore, The vehicle interior should
be checking before lock and do not
leave the bay and child or animal in
Open
Door
Luggage
boot
The
or
key can be used to lock
or unlock the doors and the luggage
boot at the same time. However, when
to open the luggage boot door, it’s the
must to open the door by opening the
pulling handle of the luggage boot door
lock manually.
The luggage boot can be unlocked or
locked by using the key. When at
unlock, rotate the luggage boot lock
with key in clockwise direction; Rotate
in reverse direction when at lock.
However, it’s the must to pull open the
opening handle of the luggage boot
with hand when to open the luggage
boot.
The luggage boot lamp will
automatically light after the luggage
boot is opened.
73
Door Lock and Anti-Theft
Release Rod of Filler
Cap
fuel tank cap can be placed on the filler
cap.
Open
Engine
Compartment Cover
3.
4.
Pull up the release rod at the left of the
driver seat to open the filler cap.
1.
2.
As shown in the figure, the screwed off
Pull up here
outward
The pulling handle of engine
compartment cover is located on
the left lower corner of the
instrument panel. The engine
compartment cover will bounce
up for certain length by pulling
the pulling handle rearward.
Stand at the front of the vehicle,
dive into the hand from the lower
portion of frond end of the engine
compartment cover till touch the
5.
pulling handle of the engine
compartment cover, pull the
pulling handle upward and at the
same time lift up the engine
compartment cover. Pull up the
release handle to open the engine
compartment cover lock.
Lift up the engine compartment
cover and support securely with
support rod.
When
close
the
engine
compartment cover, firstly lower
the engine compartment cover to
approximate 20~30 cm to the
cover lock and then release to fall
into the claw to close.
After the engine compartment
cover is closed, make sure to try
to lift up the compartment cover
to ensure if the engine
compartment cover lock is fully
74
Door Lock and Anti-Theft
engaged.
Make sure to lock the
engine compartment cover
securely during driving. In
case of the detection that the engine
compartment cover is not closed
securely during driving, stop the
vehicle immediately and close it
securely.
Remote Control System
with
Anti-Theft
Function ( )
The effects of this system are to stop
the unauthorized personnel to open the
door, luggage boot or the engine cover.
If the
or
key is
pressed accidentally (it’s
not necessary to point the
key to the vehicle, such as in the
pocket), the door or luggage boot
door will be opened.
The operation distance of the remote
controller is approximate 6 m. The
remote controller may not function
normally when the distance between
the vehicle and the remote controller is
above such distance.
The
interfered
remote
control frequency may
result the unlock failure of
the vehicle; under such case, you may
lock/unlock the vehicle by using the
key. Other short-distance wireless
emitters may also use the emission
frequency (such as amateur wireless
radio, medical equipment, wireless
earphone, remote controller, alarm
system).
Door Lock & Unlock
When press
key on the remote
controller once, all doors and the
luggage boot will be locked, at the
same time the direction lamp will flash
once and the alarm horn will alarm
once. So that the anti-theft function is
The vehicle can’t not actuate the
anti-theft function when pressing the
remote controller if the doors, front
compartment
cover
or
luggage boot is not fully
closed.
The actuation failure of anti-theft
system will have following evidence:
① Left/right turn lamps will flash
twice consecutively.
② Body anti-theft horn has no alarm.
Alarm
The left/right turn lamp will flash for
consecutive 28 s and the body anti-theft
horn will alarm for consecutive 28 s
when any unauthorized persons tried to
open the door, luggage boot and engine
hood.
activated. When press key, all doors
and luggage boot will be unlocked and
at the same time the direction lamp will
flash twice. So that, the anti-theft
system is disabled.
75
Door Lock and Anti-Theft
Remote Controller Battery
Replacement
The battery should be replaced if the
action distance of the remote controller
is shortened gradually (battery type: 3V
CR 2032).
Perform in accordance with following
steps:
1.
Open the remote controller unit
from the side clip with flat nose
tool.
2.
Pry out the battery carefully.
Install the new battery between
the two terminals with the
symbol (+) facing upward.
3.
Install the remote controller unit
in reverse order.
The anti-theft system will
enter anti-theft mode only
under the conditions that all
doors, engine hood and luggage boot
are properly closed. After the vehicle
body entered into normal anti-theft
mode, ① Four doors are locked;②
Front anti-theft indicator of the
dashboard will flash consecutively.
The used lithium battery can’t
be disposed as household waste. Please
dispose the used battery in accordance
with the regulations of environmental
protection.
76
Seat and Safety Protection
Chapter 7
Seat and Safety Protection Device
77
Seat and Safety Protection
Seat and Safety Protection
Rear
Seat
Row
Central Row
Seat
Front
Seat
Row
78
Seat and Safety Protection
y
Seat and Safety
Protection
y
Seat
Max. 25°
y
Adjust the headrest properly to
level the top end of headrest to the
top end of the head.
Do not make the front seat close to
the dashboard too much. Grasp the
steering wheel with slightly bended
arm during driving. The foot should
also be slightly bended so that it's
capable of stepping down the pedal
to the end.
The seat shoulder safety belt should
cline and pass aslant through the
chest after passing through the
middle of external shoulder. Do not
pass the safety belt through the
neck; the waist safety belt should
cline transversely through the hip
instead of the stomach.
Driver Side Seat Adjustment
Correct Sitting Posture
Seat, headrest, seat safety belt and air bag
can help protect the passenger and will
provide you with multi protection if
utilized sufficiently. Therefore, please
abide by following items:
y
Adopt vertical sitting posture; the
lower end of the back should lean
backward as far as possible with the
seatback inclination should not
exceed 25 degrees.
Knob 3
The external side of the driver side seat
cushion has three adjustment knobs with
the detailed functions as follows:
Knob 1: Used to adjust the elevation of
cushion front end.
y
Rotate the knob clockwise with
hand to move the cushion front end
upward as rotate the knob counter
clockwise to move the cushion
front end downward.
Knob 2: Used to adjust the elevation of
cushion rear end.
y
Rotate the knob clockwise with
hand to move the cushion rear end
upward as rotate the knob counter
clockwise to move the cushion rear
end downward.
Knob 3: Located at the external side of
the seatback to adjust the waist cushion.
y
The waist cushion can be jacked or
retracted by rotating the knob, till
reach the ideal position.
The seat adjustment during
driving may result the
out-of-control of the vehicle
that may result car accident, therefore
make sure to adjust when the vehicle is
stopped.
79
Seat and Safety Protection
Front Row Passenger Seat
Adjustment
Adjustment of front row seat
seatback inclination degree
Firstly, lean on the seat seatback with the
body, trip the seat right seatback
adjustment handle, and adjust the
seatback to the needed angle by changing
the body inclination angle. (The driver
seat seatback adjustment handle is at the
left side)
Seat
Fore-and-After
Adjustment
Slide
As shown in the figure, pull upward the
adjustment lever located at the seat
external front edge to move the seat
fore-and-after. Release the adjustment
lever after adjust the seat into position
and then shake the seat fore-and-after to
make sure that the seat is locked in the
slide track.
However, it will exert the protection
effects only by adjusting the headrest to
the correct position.
Front Headrest
Spring Clip
Seat
Fore-and-After
Adjustment
The top of the front row seat seatback is
installed with height adjustable headrest.
The passenger should adjust the seat
headrest to the proper height in
accordance with the body height so as to
achieve effective protection effects.
座椅靠
背调
Seat
Seatback
整手柄
Adjustment
Handle
Headrest Adjustment Method:
Headrest
The headrest can confine the movement
of the head so as to protect the cervical
vertebra in case of rear-end collision by
following vehicle during the driving.
Pull upward or push down the headrest to
the proper position after pressing and
holding the spring clip;
The best headrest height is that its top
end is level with the top end of the head.
Headrest Remove/ Assembling
Method:
During the removal of the headrest, push
down and hold the spring clip at the
80
Seat and Safety Protection
external side of the headrest guiding
element and at the same time pull out the
headrest from the guiding element.
During the assembling of the headrest,
firstly distinguish the front/rear seat
headrest (the front seat headrest is bigger
than the rear seat headrest) and then push
the headrest pin into the guiding element,
till the spring clip on the guiding element
engages with the pin correctly.
Front Row Seat Armrest
Middle Row Seat
Seat
Fore-and-After
Adjustment
Slide
As shown in the figure, pull upward the
adjustment lever located at the seat
external front edge to move the seat
fore-and-after. The adjustment method is
same with the one of front row seat
fore-and-after slide.
Rear Headrest
The adjustment method of rear headrest
is same with the one of front headrest.
Notice: Do not remove the
headrest or adjust it to the
excessive low position so as to avoid
the neck damage due to lacking of
support to the head during the
collision. It should adjust the
headrest to the proper position.
As shown in the figure, the armrest of
front row seat can be let down from the
seat side so as to promote the comfort.
Seat
Fore-and-After
Adjustment
Lever
81
Seat and Safety Protection
position by pulling the pull belt.
Adjustment of Seat Seatback
Inclination Angle
Trip the seat seatback adjustment handle
to change the central row seat seatback
inclination angle. The method is same
with the one of front row seat seatback
inclination angle.
Seatback Adjustment Handle
Folding of Central Row Seat
This vehicle can realize the multi space
combination to satisfy various demands
based on the folding combination of the
vehicle seats.
Seat Folding
Cushion Flip:
Folding of Seatback:
Pull Belt
Seat Seatback Adjustment
Handle
The cushion can be flipped to the shown
82
Seat and Safety Protection
The seatback can be folded to the shown
position by pulling the seat seatback
adjustment handle.
Rear Row Seat
Folding of Rear Row
Seat
Seat Reset
According to the following illustration,
reset the central row seat to the original
status.
Central Row Seat Armrest
The middle of central row seat seatback
has armrest that can be rolled over on the
cushion from the seatback by pulling the
pull belt. The forced rollover without
pulling the pull belt will result the
damage of the seat.
It only needs to pull it back to the
original position during armrest reset.
Pull
Belt
83
Seat and Safety Protection
The back of the rear row seat has the pull
belt that facilitating the lift of seatback
from the rear.
Please fix the articles
securely from movement if
the articles must be placed
inside the vehicle.
Try to load the luggage and
other loading articles as
forward as possible in the
luggage boot. It’s extremely dangerous
to drive the vehicle with opened
tailgate. The excessive exhaust gas
may be inhaled into the vehicle
through the opened luggage boot door.
Pull Belt
Reset of Rear Row Seat
Lift the seat seatback in accordance with
the shown direction.
Luggage Conveyance
The rear of the vehicle will have enough
space to accommodate the luggage by
folding the central row seat and the rear
row seat.
Notice: Do not exceed
the height of front row
seat when stacking the
articles such as luggage.
Do not let the passenger sit on the
folded seatback during driving,
since the luggage not bonded on the
folded seatback and the passengers
without protection device may
84
Seat and Safety Protection
the central row seat themselves and at the
same time the seat will slide forward
automatically to make space for the
get-off of rear row passengers.
collide inside the vehicle or may be
thrown out of the vehicle in sudden
brake or accident, which may result
the severe injury or death.
Get-on/Get-off of Rear Row
Passenger
Fold the central row seat seatback
forward by pulling the central row seat
seatback adjustment handle and at the
same time the seat will slide forward
automatically to make space. Therefore,
the passengers can enter into the rear row
space as pointed by the dashed arrow in
the figure.
Do not let the child sit on the
knees of the adult during
vehicle moving. This adult will
not protect the child from injury in
case of accident.
Pull Ring
For the get-off of rear row passengers,
the rear row passengers can fold the
central row seat seatback forward by
pulling the pull ring at the rear portion of
Seat Safety Belt
Make sure to use the seat safety belt/
child safety seat all the time. The seat
85
Seat and Safety Protection
safety belt can’t be shared by multi
persons. Make sure the safety belt is
fastened without any looseness, twist or
obstacle.
The driver and the passenger
at the front row are required
to fasten the safety belt
securely during driving. Avoid wearing
the wide and thick clothes. In order to
achieve best protection effects, the seat
safety belt should cling to the body.
Seat Safety Belt Alarm Lamp
This alarm lamp will light when the
ignition switch is turned on. This lamp
will keep lighting and signal the hint
sound of “dee” to remind the passenger
to fasten the seat safety belt. This lamp
will turn off when the driver side safety
belt is fastened.
Fastening Seat Safety Belt
Pull out the safety belt stably. The safety
belt may be locked when applied with
excessive force or when the vehicle is on
the slopes. The seat safety belt should be
placed on the middle of the shoulder
external side. The waist belt portion
should cling to the hip instead of the
stomach.
to the vertical position.
Insert the lock bolt into the
buckle till one click,
otherwise the safety belt is
not fastened correctly.
When to release the safety belt, push
down the red button on the buckle and let
the safety belt to retract smoothly.
Make sure that each seat safety belt uses
the correct buckle.
If the safety belt can’t be
pulled out, please pull once
with force before release.
Then the safety belt can be pulled out
smoothly.
Adjustment of Front Seat
Safety Belt Height
Central Row Seat Middle
2-Point Safety Belt
This safety belt can’t adjust the length
automatically. During use, insert the lock
bolt into the buckle till one click before
adjust the length manually to cling the
safety belt to the hip.
Do not lean the front seat too much, since
the safety belt will provide max
protection only when the seat is closing
Lock Button
The seat safety belt should absolutely not
round the neck. When to adjust the
height, push down the lock button on the
height adjuster, move the adjuster
up-and-down so that the safety belt can
86
Seat and Safety Protection
cross the middle of the external shoulder,
then release the lock button and shake the
adjuster to make sure the adjuster is
locked.
Maintenance of Seat Safety
Belt
Checking of Seat Safety Belt
Do not try to repair or
lubricate the safety belt
retractor or the buckle
mechanism and do not change the
safety belt with any means, otherwise
Chery Automobile Co., Ltd. will not be
liable for the problems arisen.
Cleaning of Seat Safety Belt
Clean with interior cleaner or clean warm
water and dry naturally. Do not use the
man-made heating method.
The safety belt should be checked
periodically for damage or worn-out.
The safety belt after stretching (such as
after the accident) should be replaced
immediately in the Chery authorized
service station and the related
components should be checked.
Do not use chemical cleaner,
boiled
water,
bleaching
powder or dye. Do not let the
water into the seat safety belt retractor
mechanism.
Air Bag (
)
The combined use of air bag and safety
belt can help reduce the danger of severe
injury in case of severe collision
accident.
Notice:
The inflation of the air bag will issue big
noise. In addition, there will have the
residue of harmless powder that similar
with smoke. All above these are normal
phenomenon.
The front row passenger can achieve the
effective protection only when at the
sitting posture as vertical as possible.
Fasten the safety belt and
keep proper distance with the
steering wheel at any time.
Only the use of the safety belt can
87
Seat and Safety Protection
guarantee that the body is at such
position that the air bag can exert the
best effects.
Front Air Bag
Extreme danger! Do not use
the reverse direction child
seat on the seat equipped
with front air bag.
posture with the lower end of the back
clings to the seatback as tight as possible
and the rearward inclination angle of the
seatback should not exceed 25 degrees.
Do not make the front seat close to the
instrument panel too much. Grasp the
steering wheel with slightly bended arm
during driving. This is the ideal driving
status that help reduce the injury danger
to the driver when the air bag is
expanding.
collision.
Keep the net space of the
front area of the air bag at
any time and do not place
anything in such area or at the top of
such area.
Only
the
trained
technicians in the Chery
authorized service station
can repair the steering wheel,
steering pillar and the air bag
system. The accident actuation of
the air bag may result the injury.
Air Bag Alarm Lamp
The seat and seatback must be correctly
positioned to coordinate in such manner
that the safety belt can achieve best
protection effects. Adopt vertical sitting
The severe frontal collision (frontal or
within 30º leftward and rightward) will
actuate the front air bag. Within the one
thousandth second of the collision, the air
bag will inflate to swell and then will
deflate when contacted with the
passenger body so as to buffer the
forwarding movement of the passenger.
The air bag will not be actuated during
the slight collision and rear or side
When the ignition switch is shifted to ON,
the indicator lamp on the instrument
panel will light approximate 3-4 s before
turn-off so as to indicate that eh system is
operational.
If the indicator lamp does not light, or
this lamp keeps intermitted lighting or
consecutive lighting during the driving, it
indicate the occurrence of the trouble. In
consideration with your safety, please
deliver the vehicle to the Chery
88
Seat and Safety Protection
authorized service station for checking.
The manufacturer for the air bag that
equipped on this vehicle recommends
renewing the air bag after equipped for
10 years, at that moment the efficiency of
the inflating agent and the effectiveness
of the air bag is deteriorated.
If you have any doubts against the
service length of your vehicle/air bag,
Chery authorized service station is
willing to query the related data for you.
The air bag system can only be dealt with
by the Chery authorized service station.
Child Safety Seat
Make sure to read carefully and abide by
the instructions of the manufacturer
during the installation of the child safety
child.
Do not hold the child on the
knees during the vehicle
driving.
baby safety seat.
Extreme danger! Do not use
the reverse direction child
seat on the seat equipped
with front air bag.
When it’s must to use child safety seat
on the front row seat, the vehicle with
PAB lock function should shift the
PAB switch to the OFF gear to disable
the secondary driver side air bag.
Please refer to the Chapter II Interior
Device Operation and Adjustment
The children less than 12 years old or
less than 150 cm height should be
securely fixed with special child safety
seat (such as baby seat, child safety seat
or heightened cushion).
The child safety belt must be suitable and
obtain the approval of the authority.
Such safety seat combined with the seat
safety belt will help provide the
maximum safety to the children.
y
The baby that less than 10 kg
weight or less than 1 year old
should be placed in the baby bed at
the rear seat, letting him/her lying
horizontal in the bed before
constrained or fixed. The best
protection method to the baby and
child is to use the reverse direction
Driving Direction
Driving Direction
y
The child less than 4 years old and
between 10 kg and 18 kg weight
should sit in the child safety seat on
the rear vehicle seat.
89
Seat and Safety Protection
Driving Direction
y
The child between 4 years and 12
years old or between 18 kg and 36
kg weight should sit on the rear seat
with heightened cushion. The
adjustable assistant safety belt that
fixed on the heightened cushion can
ensure that the diagonal safety belt
crosses the shoulder properly. The
heightened sitting position can
ensure that the adult seat safety belt
guides through the shoulder middle
correctly instead of the neck and
the waist safety belt clings to the
hip instead of the stomach.
Driving Direction
Each safety seat can only
accommodate one child.
In accordance with the
regulations of road traffic safety law,
the sitting of the child in the front seat
is prohibited. Suitable safety seat
should be used.
90
Audio
Chapter 8
Audio Part
Please read the user’s manual for audio system onboard carefully if the vehicle is
equipped with other than following audio system.
91
Audio
DVD Part (
)
92
Audio
Main Function
★ Five wave bands of FM1, FM2, FM3,
AM1 and AM2 that capable of saving 6
radio channels each.
★ Auto/manual channel search
★
Automatic
channel
saving/
programmed channel saving
★ Preview of saved channels
Play
of
Multi-Media
DVD/VCD/CD/MP3
★ Sequent play to play each song in turn.
★ Capable of power cut memory point
play function.
★ Capable of multi-media entertainment
function and identifying automatically the
media discs in DVD, VCD, CD and MP3
format.
Others:
★ Adopted high quality color LCD
screen that features clear and beautiful
image.
★ Text display and graphic expression is
correct, understandable and outstanding
and the interface color is clear, soft and
legible.
★ Capable of mute function.
Operation Safety Notices:
1) Make sure to use 12V vehicle power
supply; otherwise it may have the danger
of fire or electrical shock.
2) Do not place or install this device on
the locations that obstructed the front view
field and interfered the operation of
steering wheel, transmission lever and
brake pedal, the location that endangered
the passengers, or the locations that
obstructed the operation of the air bag
system
without
explicit
approval;
otherwise it may cause the danger of
traffic accident or body injuries.
3) Do not operate this device or replace
the CD disc during driving. If need to
conduct such operations, make sure to stop
the vehicle on safe place before such
operations; otherwise it may cause the
danger of traffic accident.
4) If the driver wants to watch DVD, make
sure to stop the vehicle on safe place
before such operations; otherwise it may
cause the danger of traffic accident.
5) Please do not disassemble or refit this
device. Otherwise it may cause the danger
of accident, fire or electrical shock.
6) In case of the occurrence of following
abnormal conditions, please stop the
operation immediately and contact with
the dealer. The continual operation may
cause the danger of accident, fire or
electrical shock.
① Foreign articles enter.
② Smoking
③ Splash of water or beverage.
④ Abnormal smell.
⑤ Occurrence of malfunction (without
image and sound)
7) In case of the breakage of the LCD
panel, please absolutely not to contact
with the liquid inside the panel. Otherwise
it may cause the dermatitis.
8) In case of the liquid ingress into the
mouth, please perform mouth wash
immediately and ask for medical
treatment.
9) In case of the liquid ingress into the
eyes or contamination on the skin, please
wash and clean with clean water and then
ask for medical treatment.
Operation Instructions
93
Audio
1. Temperature Issue
1) This device may not function normally
under extreme cold and hot conditions and
this device will resume operation when the
temperature
restores
to
ambient
temperature.
2) Do not place the device in the hot
places (such as the places with direct
sunshine and inside the vehicle under hot
summer days) and cold places; otherwise
the device may have malfunction or
deformation.
3) The normal operating temperature
range of this device is -10℃~+50 ℃.
Please operate this device within this
temperature range; otherwise it may have
malfunction.
2. Condensate Issue
In raining days, or the days with high
humidity or within short period after
heated by heater in winter, the internal
optical lens of this device will condensate
dews (water drops). It can’t use laser to
read the data under such condition and the
device also can’t conduct normal
operations.
Though subject to the
influence of the ambient environment,
under general conditions, remove the disc
and the condensates will disappear in
approximate 1 hour. Then the device can
conduct normal operation.
3. Vibration Issue
This device will result following
conditions if subject to vibration:
Music CD: The sound will be interrupted
and will resume normal operation if the
vibration disappears.
DVD-ROM Disc: Basically, it’s free of
the influence of the vibration; however,
there will be occasional evidence of image
response delay. It will resume to normal
working status once the vibration is
stopped.
4. Display Screen Issue
1) The image on the display screen may be
illegible for reading due to the light
reflection when exposed under direct
sunshine. Please avoid the direct exposure
of the sunshine.
2) The image on the display screen will be
clearest when observed from the front
direction. Please watch the image within
the range of vertical 45º and horizontal
60º.
3. The LCD screen is the product
produced by extreme high precision
technology. Its effective pixels account for
above 99.9% and there is 0.01% pixels
having defect or persistent lighting
problem. The display of red dot and green
dot within same place of the display
screen is caused from the property of the
LCD screen, instead of the fault.
4) The backlight of the LCD screen
adopted mini-scale fluorescent lamp.
Please contact with after-sales service
station if the fluorescent lamp has darker
lightness or can't light.
5. Operation Problem when
Vehicle Engine is Stopped (When
Using Vehicle Battery Power
Supply)
The operation of this device under the
condition that the vehicle engine is
stopped will have the possibility of run out
of the vehicle battery power. Therefore, do
not operate this device for a long period
when the vehicle engine is stopped.
6. Maintenance Issue
1) Please clean frequently since the screen
94
Audio
is easy to contaminate the dust. Cut the
power supply during cleaning and wipe
with soft cotton cloth. Please do not use
the wet wiping cloth nor wipe or knock
with hard object.
2) The surface of the cabinet and panel
will be corroded if contaminated with
gasoline, thinner and volatile agents such
as pesticide. Please do not use such things.
About CD
Multi-Media, DVD, CD,
MP3
DVD
left logo.
CD
Please use the discs with
Please use the discs with left
logo.
CD Operation Method
1) During the holding of the CDs, keep
your hands off from the record surface of
the CDs.
2) The CDs is rotating at high speed
during operation, please do not use the
damaged CDs or the CDs with severe
deformation.
3) Do not use the CDs with special shapes.
This kind of CDs will not only cause the
malfunction of this device, but also have
the danger of finger cut arising from the
thrown out CDs due to high speed rotation
during the removal of the CDs.
4) The CDs should be placed in the CD
case flatly and then kept in the locations
without the direct exposure of the sunshine.
Especially in summer, do not place the
CDs on the locations that exposed to direct
sunshine such as vehicle seat or the
dashboard.
5) Before use, wipe the dust, dirt and
fingerprint contaminated on the record
surface slightly from the inside to outside
with soft cotton cloth.
6) Do not use CD cleaners and static proof
agent. Also, do not wipe with the volatile
medical agents such as gasoline and
thinner; otherwise the CDs will be
damaged.
disc compartment.
1) For CD insertion: keep the print surface
facing upward and insert the CD into the
CD-ROM drive “disc compartment”
directly. At that time, the system will
automatically identify the CD and then the
user can perform corresponding operation
based on the real demands.
2) For CD removal: Press
key to
eject the CD.
Notice:
Notice to face the print surface upward
during the CD insertion.
CD Insertion/Removal
After press the
on the panel, the
device body will incline certain angle
automatically. Then, insert the CD into the
95
Audio
Operation Panel Illustration
Panel Illustration and Illustration
Automatic light measurement receiver.
The function definition for keys is shown in
the right table.
Icon Display Illustration
DVD: Indicated that DVD function is
currently in use.
96
Audio
Power
On/Power
Operation Illustration
Radio: Indicated
currently in use.
that
radio
is
Stereo: Indicated that the radio
currently plays stereo programs.
CD: Indicate that the DVD_ROM
player currently has disc inside.
Vehicle Alarm: Indicated that some
vehicle functions currently have faults.
Mute: Indicated that the system is
under mute mode;
Remote: Indicated that the current
playing radio is other than local radio
programs.
Local: Indicated that the current
playing radio is the local radio programs.
Off
Power On/Power Off Function
1. Power on and power off operation
Status description:
This product adopted electrical flexible
LCD screen with total three preset
positions:
1) The display screen will retract to the
position that parallel with the panel at
power off;
2) The display screen will protrude
automatically to form 10° inclination
angle with the panel and at the same time
display the system power on interface at
power on.
)
3) After the user presses open key (
under system working status, the display
screen will protrude out automatically and
form 45° with the panel and at the same
time the disc will be automatically ejected
from the disc compartment.
4) Under open status, place the disc and
the display screen will automatically
retract to power on status; or under open
status, press open key (
) to retract the
display screen to open status.
Notice:
1) In order to avoid the collision with the
obstacles that will cause the damage of
electrical servo mechanism during
protrusion of the display screen, please
make sure that there is free of obstacles
within 15cm of the protrusion direction of
the display screen during installation.
2) This player is equipped with system
disc jam proof function. When the disc is
at the disc opening or under disc ejection,
the system motor will automatically stop
movement to avoid the scratch on record
surface of the disc.
3) When the system motor encounters the
obstruction of obstacles during movement,
the motor will automatically stop running
after 10 s.
2. Power On Function
The normal system power on condition is
as follows:
1) When the user presses power (
) key
and the vehicle circuits are connected
(vehicle key signal is effective), then the
system will power on automatically.
2) When the user presses the power (
)
key but the vehicle circuits are not
97
Audio
connected (vehicle key signal is
ineffective), the system can power on for
operation. After power on, the system will
run no more than 1 hour; otherwise the
system will power off automatically.
Before the vehicle circuits are connected,
the system will not respond to any
operation of the POWER key so as to
protect the vehicle battery power from
excessive consumption.
3) When the user selects backup system,
the vehicle will enter into backup status
provided that the vehicle key signal is
effective and then the system will power
on automatically and enter.
Under whichever above conditions, press
power key (
status.
) to enter into power on
The power on menu needs to display the
welcome interface and hold for
approximate 2 s with the power on menu
shown in following figure:
and the display screen will retract to the
power off position;
Illustration:
The interface will display text at the same
time when the panel motor slide outward
for 10 degrees at power on. After the
display of such interface, the system will
automatically enter into the working status
before power off. If the system is powered
on for the first time, then the system will
work at radio FM1 wave band 87.5 MHz.
Notice: When power on this product for
the first time, please turn on the vehicle
circuits (vehicle key signal is effective).
3. Power Off Function
The system power off condition is as
follows:
1) When the user presses power key (
)
for 1 s, the system will turn off normally
2) Before the user presses power key (
)
to power off, the system will automatically
power off when upon the vehicle flameout
(vehicle key signal is ineffective) and the
display screen will retract to power off
position;
3) When the vehicle circuits are not
connected (vehicle key signal is
ineffective), the system will enter into
protective automatic power off when the
system is powered on and working for
more than 1 hour.
4) When the vehicle circuits are not
connected (vehicle key signal is
ineffective), the system should be powered
on by pressing and holding the power key
for 2 s so as to avoid the accident power
on that causes the consumption of the
vehicle battery power.
Notice: The sudden cut of the power
supply (BATTERY) may result the losses
of the current data and also result that the
display screen can’t retract to the normal
position. Therefore, please operate in
accordance with the normal power off
98
Audio
procedure before the power cut.
Radio
Press
key to enter into radio mode
and play the current channel with the
menu shown in following figure:
Please refer to the table for the operations
of function keys. The keys not included in
the table will have no response.
99
Audio
Preview of Saved Channels
Under radio interface, press
key
and the device will enter into the browse
status of the saved channels to browse the
saved channels under current waveband.
During the preview of saved channels, the
device will automatically search the
information of saved 6 radio channels
under current waveband with 5 seconds
play for each channel. When to receive the
radio channel currently in preview status
key
during the preview, press the
once (or the saved unit key corresponded
to the current radio channel) to cancel the
preview function and continue the
reception of the radio.
Please refer to the table for the operations
of function keys. The keys not included in
the table
100
Audio
will have no response.
of function keys. The keys not included in
the table will have no response.
Automatic Search
Under the radio interface, press key and
the device will automatically search the
radio channels under current wave band.
During the automatic search, the device
will automatically conduct one overall
search of the current radio waveband and
automatically save the searched radio
channels in the 1~6 memory units. At the
finish of automatic search, the system will
automatically enter into the preview status
of the saved channels and play the radio
channels saved in the 1~6 memory units
with 5 seconds play for each radio channel.
Please refer to the table for the operations
101
Audio
Information Menu
Press
key to enter into information
menu with the menu display shown in the
following figure:
Please refer to the table for the operations
of function keys. The keys not included in
the table will have no response.
Note: The information menu will
automatically return to original
function after 5 seconds. It also can
directly exit the information menu by
function key to
pressing the
return to original main function.
102
Audio
default setup).
Audio Setup
Under information menu, press
key to enter into audio setup interface with
the menu shown in following figure:
The setup of audio effects will directly
affect the audio output of system all
products.
Please refer to the table for the operations of function keys. The keys not
included in the table will have no response.
Audio function setup includes following
contents:
1) Audio effects adjustment
Standard (default), pop, jazz, classic, beat,
and rock.
2) Left/right balance (default: in the
middle)
3) Front/rear balance (default: in the
middle)
4) Left/right track (default: stereo)
5) Restore to default (restore to factory
Note: The color of selected item is golden.
103
Audio
the visual difference so as to achieve
Video Setup
Under information menu, press
key to enter into video setup interface with
the menu shown in following figure:
Auto light
Hue
Palette
The video function can adjust the
automatic light measurement, palette, hue,
brightness, contrast, saturation, and restore
to default.
Automatic light measurement: To detect
the ambient light strength and adjust the
display brightness automatically to reduce
104
Audio
Time Setup
Under information menu, press
key to enter into time setup interface with
the menu shown in following figure:
The time setup function is for the
adjustment of the time.
Time: Including the selection of 12-Hour
and 24-Hour (24-Hour in default). Also it
can calibrate the year, month, day, hour,
and minute.
Please refer to the table for the operations
of function keys. The keys not included in
the table will have no response.
Note: The color of selected item is golden
TFT screen light strength adjustment instruction:
User may press
key to conduct 2-level control on the light strength of the
display screen, including:
Normal
Dark
Off
105
Audio
Disc Play
When press
key, the system will
enter into disc play function and will
automatically detect the disc contents in
the DVD-ROM drive. During this period,
the system pre-reading time will be much
longer. At that moment, there has one
transitional interface as shown in
following figure.
This device may not respond to the user’s operation during loading disc
data. Please refer to the table for the operations of function keys. The keys
not included in the table will have no response.
When the drive has no disc, the system
will display “No Disc” symbol as shown
in the following figure.
106
Audio
DVD/VCD Function
DVD_ROM DVD/VCD DVD/VCD
If place the DVD disc into the DVD, the
system will start normal play.
Please refer to the table for the operations
of function keys. The keys not included in
the table will have no response.
Note: The color of selected item is golden
107
Audio
CD Function
If place CD disc into the DVD_ROM, the
system will start normal play with the
interface as shown in the following figure.
(The time and song number are shown in
the left upper corner)
Please refer to the table for the operations
of function keys. The keys not included in
the table will have no response.
108
Audio
MP3 Function
If place the MP3 disc in the DVD_ROM,
the system will display the folders of
current disc.
Please refer to the table for the
operations of function keys. The
keys not included in the table will
have no response.
109
Audio
After enter into the folder where the songs
locate, it will display the songs in MP3
format under current folder.
Please refer to the table for the operations
of function keys. The keys not included in
the table will have no response.
110
Audio
Front/Rear Balance
Options STEREO【Stereo】
L-CH【Left Mono】
R-CH【Right Mono】
3) Automatic power off of the device:
Please check if the vehicle key is inserted
properly or if using this device for 1 hour
without the vehicle key.
Please conduct adjustment or
selection in accordance with
following operations:
4) After press
key, the display
screen of the device will automatically
return within 15 s. The disc jam should be
noticed.
FADER
AUDIO
When playing the disc, press and hold
key for several seconds to display the
adjustment menu on the display screen, as
shown in the following figure:
1.
Please press these two
keys to conduct item selection.
2.
Please adjust or select the
selected item by means of these two keys.
3. At the finish of adjustment, the
adjustment
menu
will
disappear
automatically if without any operation
within 5 seconds.
BRIGHT
Brightness
CONTRAST
Contrast
COLOUR
Color
EQ
Options: FLAT【Standard】
POP【Pop】
JAZZ【Jazz】
CLASSIC【Classic】
BEAT【Beat】
ROCK【Rock】
BALANCE
Left/Right Balance
Common
Analysis
Malfunction
1) If the player can’t power on normally,
please check if the 12V vehicle power
supply, system connecting terminal or
system fuse is normal.
2) Automatic reset or power off of the
device: The system will automatically
reset or power off in case of system error.
5) When there has disc at disc opening or
the system is under disc ejection, the
motor of this device won’t start.
6) When adjust the motor to protrusion
position manually, please notice if there
has the symbol that indicated the
DVD_ROM player currently has disc
inside.
7) If the DVD_ROM player can’t eject the
disc normally, please contact with the
local dealer.
8) If the radio can’t function normally,
please check if the radio antenna is
connected properly.
111
Audio
9) When at power off, the display screen
of this device will not retract normally if
10) If the device has operation function
failure or abnormal conditions, please
conduct device reset in accordance with
the following operations. The device will
resume normal after power on.
encountered with disc jam or obstacles in
movement direction.
112
A/C System
C
113
A/C System
hapter 9 A/C System
114
A/C System
A/C System
Ventilation
The outside air enters into the vehicle via
the air inlet located in the front of
windscreen. Please keep the air inlet
under the windscreen without snow, tree
leaves and etc. in order to ensure that the
warming and ventilation function can
normally, effectively works.
115
A/C System
Windscreen vent
Side defrost vent
Side defrost vent
Instrument panel vent
Floor vent
116
A/C System
Max. airflow
air flow and direction.
Air cleaner
The air cleaner can guarantee that the
deleterious particles such as flower
powder, industrial dust fall, road dust
and etc are removed from the air before
Precautions on the regulation of
vent (the vent is regulated on
demand): the air passage and vent
jammed enable the air output to
be bad
Shut down the center and lateral vents
to make the max. airflow flow to the
pedal or windscreen.
it enters into the vehicle.
When the vehicle passes by the
automatic
car
washer,
it
is
recommended to shut down the blower
so as to avoid that the wax accumulates
Center vent and lateral
vent
on the air cleaner.
Air blowing
direction
regulation
The air cleaner shall be replaced
according to the travel environment
and the customer’s habit.
Airflow distribution
OFF
ON
The buttons on the A/C control panel
and the control device of the lateral and
A user can regulate the center and
center vents are applied to regulate the
lateral vents as required.
117
A/C System
Electronic control AUTO A/C System
Internal/external cycle
Outside Temp
AUTO mode
A/C Display Panel
OFF
Air volume +
Mode Control
A/C Compressor Defrost
ON/OFF
Air volume -
118
A/C System
A/C display panel
Temp Display
Defrost
AUTO Mode
Internal
Cycle
External
Cycle
Foot
Face
COOL mode
Blower
Run
Blower
Position
Note: A part of symbols of A/C system are displayed in the figure above. When the A/C system runs, some symbols will not appear.
The related symbol appears only in case of the corresponding run mode. So, these symbols represent the current run mode of A/C
System, which will be described in the following.
119
A/C System
The A/C system is controlled by the
electronic circuit and micro motor
which are designated to determine the
position of inlet and outlet of A/C
system.
The electronic circuit is also designated
to control the following functions
• Mode operation
• A/C compressor clutch operation
• Fan operation
• Exhaust temperature
A driver can use the A/C control panel
to select any of the following functions
• Inside temperature
• Blower speed
• Five different operation modes
1. Internal/External cycle
pushbutton
Press down this switch to circulate the
air inside the vehicle. Press up the
switch to introduce the filtered outside
air into the vehicle.
2. Temp regulating knob
This knob is designated to change the
temperature of the blew-out air. If the
knob is turned in the anticlockwise
direction to (the blue area), the air
become cold; and if it is turned in the
clockwise direction to (the red area),
the air become hot.
3. Outside
pushbutton
Press the pushbutton, the A/C panel
display will display the current outside
ambient temperature.
4. AUTO mode pushbutton
Press this switch, the A/C system will
enter into the automatic run mode.
5. OFF pushbutton
temperature
Press this switch, the A/C system will
enter into the OFF state, the display
120
A/C System
closes and all actuating mechanisms
shut down at the same time and stop
operating.
6. Mode control pushbutton
Use the pushbutton to select one of five
settings (one setting is selected every
press) to control the direction of air
flow:
(Face)
This setting is designated to introduce
the air and guide it to flow across the
vent of instrument panel;
(Face & Foot)
This setting is used to introduce the air
and guide it to flow across the vent of
instrument panel and the channel near
the floor at the same time;
(Foot)
This setting is used to introduce the air
and guide it to flow across the channel
near the floor;
(Foot & Defrost)
This setting is used to introduce the air
and guide it to flow across the channel
near the floor and the front defroster at
the same time;
To start the A/C system, press the A/C
switch. The A/C compressor will
operate automatically in the case of set
mode, unless the outside temperature is
less than 2℃.
8. Defrost pushbutton
Press this pushbutton to enable
the system to forcefully switch
into the DEFROST mode.
(Defrost)
This setting is used to introduce the air
and guide it to flow across the front
defroster.
7.A/C compressor ON/OFF
pushbutton
9.
/
(air volume +/pushbutton)
The air volume increases by one
gear every one press of the
pushbutton until up to the 6th gear
(max.);
121
A/C System
The air volume decreases one gear
every one press of the pushbutton
until down to ZERO gear (min.).
122
Emergency Procedures
Economy run of A/C system
The A/C compressor consumes the power of engine during cooling, and thus enables the fuel consumption to increase.
To save the energy and reduce the fuel consumption, please SHUTDOWN the A/C system when it is not on demand.
If there is high temperature in the compartment of parked vehicle due to the sunshine, it is recommended to open the
windows or doors to dissipate the hot air. It is helpful to improve the cooling effect and reduce the fuel consumption.
DO NOT turn on the A/C system when any window opens during the traveling.
General description
The A/C system can remove the moisture from the cooled air and the moisture will condense into water in the evaporator. So, when
the vehicle stops for a short time, there is a few water accumulation under the bottom of vehicle. It is normal.
The warming effect depends on the temperature of engine coolant. So, the warming system can fully play its role only after the
engine reaches the warm-up state.
To avoid the glass catches mist, it is recommended to place the blower on the low-speed gear position when the vehicle travels at
low speed.
It is recommended not to let the cold air directly blow to your body.
Simple operation description of the AUTO A/C system in hot whether
1.
Press the “AUTO”.
123
Emergency Procedures
2.
Press the “Internal Cycle” pushbutton, and select the inside air cycle mode.
3.
Set the temperature to “LO”.
4.
Reset the temperature to the comfort temperature after the temperature decreases.
Recommendation:
If the AUTO A/C system is used in the hot whether, please keep it on the inside air cycle state, which may reach the best cooling
effect and separate it from the outside foreign odor.
Troubleshooting
Cooling system out of service
y
The ambient temperature may be below 4℃.
y
The fuse may be burnt out.
Check the fuse, and replace it, if necessary. If the trouble is not resulted due to the fuse, shut down the A/C cooling system (press
the cooling ON/OFF button), and then let the professionals to check the system.
Cooling efficiency low
Shut down the cooling system once it is found that the cooling efficiency is low and the air volume decreases, and let the
professionals to check the system.
124
Emergency Procedures
Rear windscreen defrosting
Press the defrost heater switch to remove the cat ice and mist from the rear windscreen.
The rear windscreen-defrosting heater can work only after the ignition circuit turns on. Press the electric heater switch to turn
ON/OFF the heating system. After the heater turns on, the indicator light on the switch lights, which shows that the heater is
heating.
CAUTION:
Shut down the heater as soon as the rear windscreen is transparent in order to reduce the current consumption and save the fuel.
After defrosting for 10 minutes, or when the ignition switch is turned to the OFF position, the rear windscreen defrosting function
will automatically closes. When defrosting for below 10 minutes, please press the Defrost switch once in order to manually stop
the rear windscreen defrosting.
Activate the rear windscreen defrosting, and activate the exterior rear-view mirror to be heated at the same time.
125
Emergency Procedures
Chapter 10 Emergency Procedures
126
Emergency Procedures
Emergency
flasher light. When the ignition switch
When the fuel level is extremely low,
turns off, the hazard warning flasher
the engine will operate unsteadily
light still can operate.
within a period of time after the low
fuel indicator lamp lights, which is
Procedures
Partial operation
served as an additional alarm. In this
The engine control system of the
case, please drive your vehicle to the
vehicle
nearest gas station to refuel.
has
the
partial
operation
function. The engine still can operates
The failure to duly refuel
will make the engine
automatically extinguish and
also result the difficult start of the
engine as well as require the
emergency assistance from the
Chery’s special service station. In
addition, it may damage the engine.
when the system has fault, but the
Hazard warning flasher
light
This light is used only in case of
emergency event so as to alarm the
other
vehicle.
If
your
vehicle
extinguishes or approaches the hazard,
press this switch to turn on or off the
performance
of
the
engine
may
decrease.
Please immediately send the
vehicle to the Chery’s special
service station to have it
examined.
Duly refuel
If the fuel gauge points to
the low fuel area or if the
low fuel indicator lamp
lights, please immediately refuel.
Please
properly
use
the
compressor gun when refueling.
y
Fully insert the compressor gun
into the fuel tank. DO NOT lean
the gun on the edge of fuel filler
opening.
127
Emergency Procedures
y
If the automatic compressor gun
avoid that the fuel overflows from
DO NOT directly hold the glass of bulb
is
automatic
the fuel can and thus a fire
by hand, otherwise the fingerprints
shutdown of the gun during
available,
the
disaster occurs when an accident
remained on the glass will be heated
refueling indicates that the fuel
is met.
and volatilize after the lamp lights, and
tank is fully refueled. In this case,
then deposit on the surface of mirror to
DO NOT try to continuously
make the reflector blacken.
refuel, otherwise there is no
When the bulb is replaced, the same
swelling space in the tank, and the
fuel will overflow from the tank if
the temperature increases.
y
y
y
Replace the bulb
model of bulb must be used. Please
Unless the event is very emergent, it is
before installation.
check the specification of the bulb
Please tighten the tank cup after
unallowable that the owner himself
refueling.
replace the bulbs of headlamp unit.
Please
keep
to
the
local
Since the front bumper shall be
regulations and rules concerned
removed
when the canned spare fuel is
replaced, it is very difficult to do it if
carried.
there is no special tools. If it is
For the sake of safety, it is
recommended not to carry the
canned spare fuel in order to
Headlamp bulb:
before
the
headlamp
is
12V 55W
necessary to replace these bulbs, please
turn off these lamps and disconnect the
ignition switch before any bulb is
replaced.
128
Emergency Procedures
Turn signal, back-up,
Stop/position
rear fog lamps bulb:
bulb:
lamp
after the headlamp unit is removed.
1.
bonnet.
2.
12V 21W
12V 21W/ 5W
License plate, position,
turn
signal
bulb:
Unscrew the protecting hoods
from the low beam and the
high
beam bulb in the anticlockwise
Front fog lamp bulb:
direction
according
to
the
position as shown in the diagram.
and
high-mount stop lamps
Open the engine compartment
Remove the harness connector
12V 55W
from the bulb, press downward
After the headlamp bulb is
replaced
every
time,
calibrate the headlamp. The
Chery’s special service station can
offer you the service.
the clip of bulb holder by hand so
as to make the clip get through
the location groove and split
towards the both sides, take out
12V 5W
Headlamp
unit
beam/low
beam/position/turn
lamps inclusive)
the bulb, and pay more attention
(high
signal
Any bulb above can be removed only
to the location mark of the bulb.
3.
CAUTION:DO NOT touch the
surface of new bulb by hand in order to
avoid it affects the brightness of the
129
Emergency Procedures
bulb. The lighting system is a safety
component, please pay more attention
on the replacement of it and ensure that
any detail must be proper in case of
Front fog lamp bulb
anticlockwise
direction,
remove the harness connector
Please get to the Chery’s special
from the tail lamp, and take out
service station to replace the front fog
the tail lamp.
lamp bulb.
replacement. Get to the Chery’s special
service station to have it repaired, if
the
2.
Tail lamp bulb
Unscrew the protecting hoods
from
necessary.
the
bulb
in
the
anticlockwise direction according
Stop Lamp Holder
to the position as shown in the
diagram.
Position Lamp Holder
3.
High Beam
Holder
Turn Signal Lamp
Holder
Remove the harness connector
from the bulb, press downward
the clip of bulb holder by hand so
as to make the clip get through
1.
Turn Signal
Lamp Holder
Low Beam Holder
The position lamp bulb can’t be
replaced. If the bulb fails to work,
please immediately get to the Chery’s
special service station to have it
repaired.
Open the tail door, and unscrew
the location groove and split
the two nuts (under the plate
towards the both sides, take out
guard) used to fix the tail lamp
the bulb, and pay more attention
from the internal side of luggage
to the location mark of the bulb.
boot
in
the
anticlockwise
direction. Then, unscrew three
4.
CAUTION:DO NOT touch the
surface of new bulb by hand in
fixing bolts from the tail lamp in
130
Emergency Procedures
order to avoid it affects the
brightness of the bulb. The
lighting
system
is
a
safety
component, please pay more
attention on the replacement of it
and ensure that any detail must be
High-mount stop lamp bulb
The high-mount stop lamp bulb can’t
be replaced. If the bulb fails to work,
please immediately get to the Chery’s
station to have it repaired, if
necessary.
The position lamp bulb can’t be
replaced. If the bulb fails to work,
1.
Turn off the interior lights.
repaired.
2.
Insert the screwdriver into the
6.
license plate.
1.
and take out these screws.
2.
take out the lampshade.
3.
Remove the self-tapping screws
used to fix the license plate lamp,
Replace the bulb, and install the
reflector.
4.
Reinstall the lampshade into the
installation hole located on the
Draw out the holder and take out
lamp housing.
the bulb damaged.
Install it in reverse order.
After installation, check whether
and lampshade, and carefully
Installation position: On the top of
special service station to have it
5.
gap between the lamp housing
License plate lamp bulb
please immediately get to the Chery’s
repaired.
Internal front/rear ceiling
lamp bulb
special service station to have it
proper in case of replacement.
Get to the Chery’s special service
tighten the lamp.
3.
the lamp works normally.
4.
Install the new bulb into the
Sun visor mirror light:
holder, and then install the holder
Installation position:On the rear of sun
well.
visor.
Use the self-tapping screws to
Take out the mirror and then replace
131
Emergency Procedures
the bulb.
relation with the safety of travel. So, it
spare fuses with the vehicle in order to
is allowable to regulate the beam only
prevent some unexpected events.
Luggage boot lamp bulb
using the special instrument. During
Installation position: On the side of
adjustment, please abide by the laws
luggage boot.
and regulations concerned.
1.
Insert the screwdriver into the
gap between the lamp housing
and lampshade, and carefully
take out the lampshade.
2.
Replace the bulb.
3.
Reinstall the lampshade into the
Fuse and relay
There are various specifications of
fuses stocked in the Chery’s special
service station.
The fuse burnt can be identified using
the fuse disconnection method. All
Before the fuse and relay are
replaced, shut down the
ignition switch and all
electrical equipment.
fuses are push-on type ones.
Fuse
installation hole located on the
lamp housing.
Replace the fault fuse with the new
fuse of the same rated value. The
position of the fuse box containing the
main fuse and relay is shown in the
figure.
Regulate the
headlamp
beam
of
Whether or not the adjustment of
headlamp beam is proper has the direct
The professional knowledge is required
Cartridge fuse
to replace the relay.
It is recommended to carry several
132
Emergency Procedures
Replace the fuse
Fuse Color Code
Any unauthorized alteration
of the vehicle’s electrical or
fuel system may make an
influence on the performance of the
vehicle and cause the fire disaster or
potential
hazard.
So,
it
is
recommended that any work related
to the removal of fuel or electrical
system and the replacement of relay
shall be conducted by the Chery’s
special service station.
Color
Current (A)
Tan
5
Brown
7.5
Red
10
Blue
15
Yellow
20
Your vehicle is accompanied by a fuse
puller. You can find it from the engine
compartment fuse box.
Cartridge Fuse Color Code
Color
Current (A)
Green
30
Pink
40
Yellow
60
133
Emergency Procedures
Engine compartment fuse box:
The fuse box is located at the right side of engine compartment and at the rear of battery. When the fuse is checked or replaced,
loosen the claw and then pull up the bonnet to remove the fuse box cover plate (“B+” is the main power supply of fuse box).
134
Emergency Procedures
Replace the wheel
Before the vehicle is lifted
up, please stick to the
following precautions.
Stop your vehicle on a proper location,
please make sure that it neither affect
the traffic, nor endanger your safety
Spare wheel
unscrew the glove box fixing
bolts (each one at right and left
If the dimension of some one
wheel (either steel ring or
tire) is different from that of
other wheels installed, please abide
by the following regulations.
sides)
in
the
anticlockwise
direction., and take out the glove
box.
The spare wheel is located under
the chassis and at the rear of rear
axle.
during the replacement of tire.
Please ensure that the vehicle is placed
on a stable, level ground. If necessary,
a proper wedge is used to block the
wheel in order to further secure your
2.
vehicle.
Please make sure that the
Take out the spongy cushion
under the glove box, and use the
driver tool – socket wrench to
front wheel
faces to the right ahead.
If the vehicle is equipped with the
automatic transmission, please select
the P gear position.
unscrew the spare tire towing
Procedure to replace spare tire:
hook nuts in the anticlockwise
1.
direction.
Take out the cover plate of
luggage boot glove box, use the
driver tool -- cross screwdriver to
135
Emergency Procedures
To lift up the vehicle using a
jack is suitable for the
replacement of wheel only.
In this case, DO NOT operate under
the bottom of vehicle.
convex part.
The position shall be close to the wheel
to be repaired A.S.A.P.
Groove
3.
When the towing hook bolt is
unscrewed, detach the towing
hook from the support used to fix
the tire and then take out the
spare tire.
(Reinstall the tire in
The max. working load of
jack is 1,000Kg.
the reverse order.)
Front wheel jack lift
point
Rear wheel jack lift
point
Remove the wheel
The jack is located at the front of
luggage boot spare wheel.
1.
Make sure that the vehicle is
placed on a stable, level ground
and the front wheel faces to the
Jack lift point
right ahead.
The jack can push against only the
Jack
special position of bottom of the
2.
Turn off the ignition switch.
vehicle shown in the figure below. The
3.
Please select the P position of
groove of jack pushes against the
automatic transmission.
136
Emergency Procedures
4.
Install the wheel
Tell the passengers to leave the
vehicle.
5.
6.
1.
If necessary, use the proper wheel
tighten the wheel nut in the
stopper to secure the vehicle in
clockwise direction and make
order to avoid the roll or slide.
sure that the tip of wheel nut
faces to the wheel.
Insert the flat head screwdriver
2.
into the gap between the steel
Lower the vehicle and remove
the jack.
ring and hub cap, and carefully
turn it to remove the hub cap.
7.
Push the wheel to the rim bolt,
3.
Utilize the diagonal tightening
Place the jack, and ensure that the
method to fully tighten wheel
the special tool to unscrew the
whole seat is located on a solid
nuts (the tightening torque is
wheel nuts.
ground.
110±10 Nm).
As shown in the figure below, use
8.
9.
The jack must vertically lift up to
4.
your both hands.
the jack lift point.
10.
Lift up the vehicle until the wheel
5.
them.
Remove the wheel nuts and then
take out the wheel.
Collect the jack and fault wheel,
in the reverse order and fasten
departures from the ground.
11.
Steadily press the hub cap by
6.
Do best to send them to the
137
Emergency Procedures
Chery’s special service station to
on the glove and safety goggles.
check the tightening torque of
DO NOT let the acid or lead
wheel nut and the tire pressure.
touch your skin or clothes. DO
y
Keep the children away from the
battery acid.
NOT tilt the battery, otherwise the
acid may flow out from the vent.
Battery
If the acid splashes into your eye,
Recommendations on safety
to wash your eye for several
When
the
battery
is
delivered, take the following
countermeasures.
immediately use the clean water
minutes
and
take
y
When the battery is charged, it
can emit the highly-explosive gas.
medical
treatment at once. If the acid
splashes to the skin or clothes, use
the alkaline water (soapy water)
to neutralize it and then use the
y
Open flames, sparks and smoking
clean water to rinse it. If you
prohibited. When the wiring and
unfortunately
electrical
eat
the
acid,
operation
conduct,
immediately get to hospital to see
please avoid the spark generation.
doctor.
Please DO NOT connect the
electrical terminals. Any short
circuit caused may create spark
y
The battery acid is corrosive. Put
and give rise to injury.
138
Emergency Procedures
current and capacity of new
battery must be the same as that
of old battery or conform the
Chery’s specifications. For the
y
There is high voltage in the
proper
electronic ignition system. Please
please contact the Chery’s special
DO NOT touch these components
service station.
when the engine is operating or
y
the ignition switch turns on.
y
y
specifications,
After the ignition switch and all
y
After the battery is removed and
reconnected, the performance of
the vehicle may be somewhat
abnormal at the early stage. This
is the engine control system is
readapting the engine. It can’t be
considered.
electrical equipment turn off,
The used battery contains the
please remove the negative (-)
Removal and Installation
When the removal and installation of
the battery, take the following
countermeasures:
battery
and then the negative (-) cable.
cables first.
y
sulphuric acid and lead. DO
NOT dispose them as the common
Carefully operate in order to
household waste. Please send them to
avoid that the metal tool touches
the local qualified waste disposal
Your vehicle is equipped with the
the both electrical terminals of
station.
12 V 75A•h maintenance-free
batter at the same time or contacts
lead-acid battery.
the positive terminal and vehicle
body by accident.
Replace the battery with the
lead-acid one, and DO NOT use
other kinds of batteries. The
y
When the battery is reconnected,
connect the positive (+) cable,
139
Emergency Procedures
Engine battery-assisted
start method
1.
order to avoid that they don’t
Connect the down-lead
If there is no power in the vehicle’s
touch each other.
2.
battery, introduce the power of other
equipment.
engine to start.
3.
Connect the battery of the same
the jumper wire with the insulating clip,
battery from the electrical system of the
Connect the positive (+) terminal
of the low power battery to the
Low Power
Battery
positive (+) terminal of the
support battery via the wire A.
and the cable with proper dimension.
Please DO NOT remove the low power
Extinguish the engine, and turn
off any unnecessary electrical
vehicles into the vehicle and help the
nominal voltage (12V) only. Please use
Properly stop these vehicles in
Support
Battery
vehicle.
140
Emergency Procedures
4.
Connect one terminal of wire B
to the negative (-) terminal of the
support battery, the other terminal
to the metal part of the engine to
be started. Position the jumper
wire in order to avoid it contacts
the motion parts in the engine
To reduce the voltage surge
during removal, please turn
on the blower and electric
heating type rear windscreen of the
vehicle with low power battery.
Please DO NOT turn on the headlamp
to substitute the electric heating type
rear windscreen, otherwise the surge
voltage may burn out the bulb.
the low power battery, and start
compartment.
the vehicle with the low power
DO NOT connect to the
negative (-) terminal of the
low power battery.
5.
Make sure that the jumper cable
battery
within
one
second
A.S.A.P.
3.
Let the two engines of vehicles
can’t interfere with the motion
operate for three seconds before
parts of engine.
the down-lead is removed.
Start the engine
Remove the down-lead
1.
y
The engine of vehicle equipped
with the support battery operates
Remove the down-lead B(-), and
Tow truck
There are trunk rings equipped at the
front and rear of the vehicle in order to
install the tow cable.
During towing, slowly and smoothly
travel to avoid the tow truck bounces.
The big tow force may damage the
vehicle.
During towing, the ignition
switch of the vehicle to be
towed shall be placed on the
“ON” position to make the steering
wheel, turn signal lamp and stop lamp
work. Since the engine extinguishes,
there is no brake boost and steering
boost. The required operating force
need to be increased. So, the power of
brake
and
steering
shall
corresponding increases.
then the down-lead A (+).
at the proper high speed.
2.
Start the engine of vehicle with
141
Repair and Maintenance
Chapter 11
Repair and Maintenance
143
Repair and Maintenance
It is essential to take the regular
maintenance on your vehicle during the
Care
and
course of use. Please implement the
are recommended in the Instruction
Manual. Otherwise, it may damage
your vehicle.
maintenance strictly according to the
maintenance schedule provided in the
Instruction Manual in order to ensure
Maintenance
that your vehicle is kept the best
The Chery’s special service
station offers you the best
services
performance and better running state
Only the genuine spare parts and
and effectively extend the vehicle
materials can ensure the service life of
In addition, it also lets
The care and maintenance can be
your vehicle, and, here, please pay
you find and remove the potential
divided into two categories. One is the
more attention: the Chery Automobile
hazard in time to avoid the occurrence
routine care and maintenance which
Co., Ltd. offers the Chery’s special
of
following
can be implemented by the owner
service station nationwide the genuine
paragraphs, we will describe in detail
himself/herself, and the other is the
spare parts only. So, you get the
the routine maintenance, examination
regular
genuine spare parts from the Chery’s
and care method. Please read it
examination and repair, which shall be
special service station only.
carefully.
carried out by the Chery’s special
The Chery’s special service station is
service life.
the
fault.
In
the
care
and
maintenance,
service station.
the unique professional service station
Please strictly use the oil, gasoline,
authorized by the Chery Automobile
brake fluid and anti-freeze fluid, which
Co., Ltd.. The staffs have taken the
144
Repair and Maintenance
strict professional training organized
and braking function are normal. Check
by the Chery Automobile Co., Ltd..
the warning lights. (See the Regular
General maintenance for a
vehicle
They will do their best to offer you
Maintenance Schedule below for your
The washing area where the
the best high-quality after-sale service.
reference) .
ecological
If you dissatisfy the work of the
Chery’s special service station, please
feel
free
to
email
it
to:
Cheryservice@myChery.com. We will
response to your questions very
quickly. When emailing, please do not
forget to explicitly note the model,
chassis number, engine number, road
mileage, and delivery date in your
The
reservoirs for the brake fluid,
Regularly check the level of fluids and
refill the fluids concerned. Check
whether or not the tire pressure, lamps
system
can’t be damaged is available only.
coolant and power steering fluid are the
The used engine oil, brake
semi-transparent containers which are
fluid, anti-freeze fluid, battery
convenient to quickly, visually check
and tire are disposed by the qualified
these fluids.
waste disposal mechanism only or you
There is the high voltage in
the electronic ignition system.
Please DO NOT touch these
parts when the engine is operating or
the ignition switch turns on.
consult the related manufacturers about
Turn off the ignition switch
before working in the engine
compartment. Even if the
ignition switch turns off, the cooling
fan also operates automatically. So,
please take care of your clothes (tie)
not to be caught by the fan or driving
belt.
Everyone shall concern about the
email.
Items you must follow
drainage
the disposal method. DO NOT disposal
them as the household waste or drain
them into the public drainage system.
environmental protection and do our
best to protect environment.
145
Repair and Maintenance
Maintenance Schedule
CAUTION: *
Monthly check:
Daily check:
y
Coolant level (for engine cold
state)
Check the working condition of all
exterior and interior lamps and lights.
The air conditioner shall operate for
y
Whether or not there is leakage
Replace the damaged or dim bulbs,
in the assy., pipelines, hoses and
and make sure that all mirrors are
oil reservoirs
clean.
Please check the following
items when refueling:
y
Engine oil level
y
Brake fluid level
y
Windscreen cleaning fluid level
y
Tire pressure and status (for cold
y
Brake fluid level
y
Power steering fluid level
y
Whether
or
not
the
above 30 minutes every month.
Keep the vehicle oil, grease
lubricant and fluids out of the
reach of children. Abide by
the safety instructions on the
containers to avoid your skin contacts
the used oil.
air
conditioner works well*
y
Whether or not the hand brake
works well
y
Whether or not the horn works
well
state only)
146
Repair and Maintenance
Engine compartment maintenance items
Brake Fluid Reservoir
Engine Oil Dipstick
Coolant Reservoir
Power Steering
Fluid Reservoir
Air Cleaner
Fuse Box
Battery
Windscreen Cleaning
Fluid Reservoir
Engine Oil Filler
Cap
Automatic Transmission
Oil Dipstick
147
Repair and Maintenance
the normal working temperature of the
Engine oil dipstick
Engine oil filler cap
engine is still unavailable). Before the
engine oil is checked, DO NOT start the
engine at the cold state. Draw out the oil
dipstick
MAX MIN
The engine oil is affected by many
factors. A new engine reaches the normal
operating
specification
only
after
traveling approx. 5,000 Km. More engine
oil might be consumed when the engine
operates with high load.
Regularly check the engine oil, e.g. when
refueling or before a long-distance
journey.
and
clean
it
with
the
flannelette-free cloth. Carefully insert it
and draw it out again.
If the level of oil is between the MIN and
MAX marks on the lower of dipstick, DO
Turn the filler cap in the anticlockwise
NOT refill the oil. The hot oil may
direction and pull out it to open the filler
exceed
cap. Please DO NOT open the filler cap
the
MAX
mark
several
millimeters due to the thermal expansion.
when the engine is operating.
If the level of oil is located at the lower
MIN mark or below, refill the engine oil,
which
conforms
to
the
Chery’s
Stop the vehicle on a level ground before
specifications, to the position between the
the engine oil is checked. Turn off the
MIN and MAX marks only. For the
ignition switch and wait for several
details, see the chapter “Capacity and
minutes in order to let the engine oil flow
Specifications”.
Please DO NOT use the oil
additives or engine treating
compound. It is not only
unnecessary, but also may
damage the engine in certain cases,
without the warranty.
Turn the filler cap in clockwise direction
into the oil sump (It may need more time
until the “Kala” sound is heard. It means
when the outside temperature is low or
that the filler cap is closed.
148
Repair and Maintenance
The
household
waste
Engine coolant reservoir
is
unallowable to be placed into
the empty oil container and disposed.
When these wastes are disposed, please
储液壶位于 engine 仓右后部. 油位必
make use of the local waste disposal
The level of oil shall be between the MIN
facilities qualified.
and MAX marks at the reservoir side. If
the level of oil drops down to the MIN
Brake fluid/clutch oil
Please DO NOT let this fluid
contact your skin or eye. If
the occurrence of this case,
please use a lot of clean water to wash
the position affected and immediately
get to see a doctor.
The brake fluid and clutch oil (exclusive
at automatic gear position) are supplied
by the same reservoir.
mark, the brake fluid warning light will
light.
The brake fluid which conforms to the
Chery’s specifications is available only.
See
the
chapter
“Capacity
and
Specifications”. Send it to the Chery’s
special service station A.S.A.P. to check
the leakage of the system.
Ensure that the brake fluid refilled is
absolutely clean.
If the fluid contacts a surface
painted, please use a wet
sponge to remove the fluid or
use enough water to wash the surface
painted.
DO NOT open the cover of
reservoir
when
the
temperature of engine is
extremely high. Otherwise, the coolant
may spray out from the system and
result the scalding or corrode the other
parts and components.
The level of coolant can be seen through
the semi-transparent reservoir. When the
engine is in the cold state, the level of
coolant shall be between the MIN and
MAX marks. When the engine is in the
hot state, the level of coolant may exceed
the MAX mark due to the thermal
expansion.
Refill the coolant only when the engine is
in the cold state. If you have to refill it
while the engine is in the hot state, wait
for 10 minutes to cool the engine. Turn
149
Repair and Maintenance
the reservoir cap a quarter turn to relieve
the accumulated pressure. Then, fully
open the cap after a period of time. Refill
the coolant suitable for the specification
Please DO NOT use the
coolants with different colors
and specifications.
of the vehicle.
protection for a engine.
So,
please
use
the
drop down any more, and then screw on
coolant
which
conforms to the Chery’s specifications.
DO NOT use the tap water to substitute
the coolant.
For the capacity, please refer to the
The coolant is a kind of
noxious fluid. DO NOT use it
to wash your hand or clothes.
Carefully refill the coolant in order to
avoid it splashes on the any position of
engine. If the fluid contacts your skin
or eye by accident, please use enough
clean water to wash the position
affected and immediately get to see a
doctor.
the reservoir cap.
chapter “Capacity and Specification”.
Automatic transmission oil
level
Refill the coolant
1, Unscrew the reservoir cap, refill the
coolant up to the MAX mark, and operate
the Chery’s special service station will
the engine to make the temperature of
check the level of automatic transmission
water reach approx. 90℃. DO NOT
oil
unscrew the reservoir cap because there
The coolant with proper concentration
maintenance on your vehicle. Get to the
are some gases draining from the water
cannot only prevent the engine from be
Chery’s
passage. In this case, the level of fluid in
frozen in winter, but also provide the
recommended
the reservoir will drop down;
automatic transmission oil.
2, Turn off the engine, refill the coolant
Replace the transmission oil once every
into the reservoir and repeat the process
approx. 100,000 Km road mileage. In
above until the level of reservoir doesn’t
case of the severe condition, replace the
anti-corrosion protection all the year
around. The engine now operates at the
extremely high temperature, and the bad
coolant
cannot
provide
the
proper
when
it
conducts
special
the
service
station
to
routine
station
or
refill
the
150
Repair and Maintenance
automatic transmission oil once every
40,000 Km road mileage. During the
routine examination, if it is found that the
color of transmission oil becomes black,
brown or there are obvious foreign
materials
in
the
oil,
replace
level of fluid shall reach the MAX mark.
If the level is below the
new battery must be the same as that of
MIN mark,
please refill the specified fluids.
the used battery or conform to Chery’s
specifications. For the proper battery
specifications, please contact and consult
the Chery’s special service station.
Battery
the
Windscreen washer system
transmission oil.
Model of transmission oil: DIAMOND
ATF—SP-Ⅲ.
Check the level of power
steering fluid
Few maintenance is available for the
battery. The level of fluid will be checked
during the routine maintenance and
examination.
Your
vehicle
maintenance-free
is
equipped
battery.
It
with
is
a
not
recommended to use the other model of
When the engine is in the cold state, the
batteries. The current and capacity of a
The front and rear washer system are
watered by the same reservoir. If
necessary, mix the clean water and
windscreen
cleaning
fluid
in
the
concentration of 1:20.
151
Repair and Maintenance
Please screw up the reservoir cap after
refilling.
Replace the wiper blade
the details, refer to the tire pressure
recommended in the chapter “Capacity
and Specification”.
Check the wiper blade
Comply with the correct tire pressure in
particular when the vehicle travels at
heavy load and high speed.
The tire
pressure insufficient may reduce the
Raise
the
wiper
arm
until
it
is
perpendicular to the wiper blade. To
remove the wiper blade, press down the
stability of the vehicle, increase the
rolling resistance and quicken the wear of
tire, and also result the damage which
may cause the traffic accident.
Slide your fingertip on the edge of the
retaining clip in the arrow direction,
wiper blade to check its coarseness. The
release the wiper blade and then pull
If you have to drive your vehicle on the
butter, silicone resin and fuel may result
away the wiper arm in the reverse
edge of road, you slowly drive it only. If
the wiper blade failure to work. It is
direction.
possible, the wheel
approach
recommended to use the windscreen
cleaning fluid to clean the wiper blade.
Tire
the
shall vertically
roadside.
Avoid
the
upstanding obstacles with sharp edge.
Take care not to scratch the lateral wall of
For the sake of safety, when refueling,
please check the pressure of tires (incl.
spare tire) after these tires cool down. For
tire when the vehicle stops.
Regularly check whether there are the
flesh cut, foreign material and uneven
152
Repair and Maintenance
The improper tire and wheel
rim may result the traffic
accident,
without
the
warranty.
Dispose the worn tire according to local
use the genuine tire when the tire is
regulations on environmental protection.
installed
Change the winter tire to summer tire as
recommendation from the Chery’s special
soon as road condition permits, which
service station.
wear on the surface of tire. The uneven
can reduce fuel consumption and lower
wear of tire tread indicates that the wheel
the noise.
or
to
refer
to
the
alignment may be wrong.
Replace the tire
The tire available for your vehicle is
properly selected to provide the best
operation, comfort and safety. The above
specifications on the tire-wheel rim
combination are suitable for the steel or
The depth of the tire tread wear is
aluminum alloy wheel rim. To understand
illegally limited. After the wear reaches
whether the other kinds of tires
the limit value of 3 mm, there is a wear
wheel rims are used in this vehicle,
strip occurring on the tire tread,
please contact the Chery’s special service
which
indicates
that
the
and
station .
CAUTION:
The pedometer is affected by the
dimension of tire applicable for the
vehicle. If the tire dimension (diameter)
is different from that of the genuine tire,
the exact speed can’t be displayed.
Snow tire chain
performance and safety of the
The snow tire chain can be applicable for
tire reduce considerably and the tire must
the summer and winter tires while is used
be replaced.
It is strongly recommended to
on the driving wheel (front wheel) only.
153
Repair and Maintenance
When the snow tire chain is in service,
Drive belt
CAUTION:
the performance of the vehicle equipped
with the snow tire chain control system
The drive belt is one of the parts subject
may be somewhat abnormal, and this
to the most severe stress. Therefore, the
The driving belt may somewhat extend
symptom can be removed when the
belt must be of high quality and reliable
after it is in service for a certain time, and
system shuts down.
to meet operational needs.
the belt will be loose when the extension
reaches the limit, which may result the
To avoid the damage of the full-diameter
fault and damage the vehicle. So, the
wheel cap, remove the cap before the
When the drive belt is replaced, it cannot
tension of generator belt shall be checked
snow tire chain is installed.
meet the requirement if the belt with the
after the vehicle travels 1,000 Km.
Immediately install the wheel cap after
same dimension is selected only. For the
the snow tire chain is removed.
sake of safety, please use the Chery
Check the tension of drive belt
genuine belts only. The Chery’s special
1.
service station has the genuine driving
take out the key.
belt.
1. The speed shall not exceed
50 Km/h when the snow tire
chain is available.
2. The snow tire chair shall
be immediately removed in
case that there is no snow
on the road.
Turn off the ignition switch, and
If you want to install a
nonstandard tire or wheel
rim, (e.g., light alloy wheel
rim or wheel with winter tire), comply
with the related instructions or contact
the Chery’s special service station.
2.
Press the intermediate position of
the belt with your thumb (approx.
100 N), and check the flexibility of
154
Repair and Maintenance
Use the cold or slightly-warmed
water to wash the vehicle only.
the belt:
Max. allowable flexibility: 10 mm.
3.
If
the
flexibility
allowable
exceeds
value,
After the vehicle is cleaned,
step on the brake pedal service
times to remove the moisture
from the brake disc during the journey.
please
special service station to have it
regulated.
Clean the headlamp
Automatic vehicle washer
Wash the vehicle
DO NOT throw the cleaning materials
into the household waste. Please make
use of the local waste disposal facilities
qualified.
of headlamp, DO NOT use the corrosive
employ the brushless facilities in a good
abrasives or chemical solvents. DO NOT
vehicle-washing workshop. The powerful
wipe the lamps when the mirror is dry, or
waterflow may be sprayed into the
use a keen-edged object to clean the lens.
vehicle if the vehicle-washing system
with high-pressure water is available.
drainage
Before the automatic vehicle
washer is available, please
turn off the heating blower
system
can’t be damaged is available only. The
most important factor to protect the
painted surface of the vehicle is to use the
To avoid the damage of the plastic mirror
The best method to wash a vehicle is to
The washing area where the
clean water.
vehicle, and clean the vehicle with a dry
cloth.
the
immediately get to the Chery’s
ecological
please use a lot of water to wash the
first.
Clean the rear windscreen
When the rear windscreen is cleaned, use
the soft cloth to wipe it only in order to
avoid
the
damage
of
the
heating
components or radio antenna. DO NOT
Wash the vehicle manually
use the solvents or keen-edged objects to
If the vehicle cleaning fluid is available,
clean the windscreen.
155
Repair and Maintenance
Chassis anti-corrosion
The
vehicle’s
chassis
has
already
conducted the anti-corrosion treatment.
Regularly
anti-corrosion
check
the
protection,
chassis
and,
if
damage the special machined surface.
Paintwork protection
The cleaning products
Wax your vehicle once or twice every
year to keep the paintwork smooth,
To get the best effect, please properly use
better.
the vehicle care products.
necessary, get to the Chery’s special
Leather fabric care
service station to have it repaired.
Use the wet cotton cloth and tower to
wipe the leather surface, and dry it with a
clean soft cloth. Use such the neutral
cleaning agents as soap foaming agent to
clean the extremely dirty surface. During
To ensure the permanent the
paintwork of the vehicle, remove in
time the substances harmful to the
paintwork, such as: bird droppings,
resin, insect residuals, tar spots, road
snow-removing salt, industrial waste
and etc.
the normal service period, it is
recommended to use the special curing
agent for leather to care the leather once
every six months.
Clean the wheel
On the basis of the road mileage, clean
the wheel once every week in order to
avoid the dust accumulates on the brake.
Employ the wheel cleaning agent or
warm water and soft sponge to clean the
The proper leather cleaning
materials and cleaning agents are
available only.
Paint removing treatment
wheel. DO NOT use the abrasive
For the paintwork damage or slight
materials to clean it in order to avoid they
scratch created due to the ballast on the
When the vehicle is polished,
take care not to let the polishing
compound to contact the plastic
surface. Otherwise, it is difficult to
remove it. In addition, DO NOT polish
the vehicle in the strong sunshine.
road, please get to the Chery’s special
service station to have it treated.
DO NOT let the leather over-wet,
especially par more attention not to make
the water enter into the gaps.
156
Repair and Maintenance
Clean the radiator
After the vehicle travels for a period of
time, the windward side of the condenser
and radiator may be jammed by some
insects, tree leaves, and other foreign
materials. In this case, it will make an
influence on the performance of the air
conditioner and cooling system, which
results the air conditioner failure to
operate normally, cooling system
over-heat and etc. So, it is necessary to
clean the radiator and condenser.
It is advisable that the front surface of
radiator is cleaned once every year. Use
the compressed air or water to clean the
fins of radiator, blow by the small insects,
bugs, tree leaves and etc.
exceed 150 KPa. If the pressure exceeds
150 KPa, it may damage the fins o f
radiator.
Through the radiator, blow the gas from
the rear to the front of the radiator to
clean the condenser. When the engine is
in the cold state, use the water to wash
the radiator.
The pressure of air and water shall not
Regulations on the regular maintenance
Please get to the Chery’s special service station to have your vehicle maintained according to
the specified mileage.
The fins of radiator are
essential to conduct the better heat
conduction. DO NOT brush these fins.
Otherwise, it may damage the fins and
reduce the heat conduction.
DO NOT spray the water on the hot
radiator because the hot gas generated
will make people injured.
Use the water to wash the radiator only
when the engine stops operating and
cools down.
Mileage (Km)
Maintenance Item
5,000
15,000
30,000
157
Repair and Maintenance
Mileage (Km)
Maintenance Item
5,000
15,000
30,000
Lighting, warning flasher devices, horn: Check the performance
★
★
Wiper and cleaning equipment: Check the performance, and add the cleaning fluid, if necessary
★
★
Check the free travel of clutch and the clutch fluid level, and regulate it, if necessary
★
★
Engine oil: Replace it
★
★
★
Oil cleaner: Replace it
★
★
★
Transmission oil: Check the level of oil, color and quality of oil, and refill it, if necessary
★
★
★
Engine : Check the leakage (engine oil, anti-freeze fluid, fuel, A/C system and etc)
★
★
★
★
★
Battery : Check the level of electrolyte, and refill the distilled water, if necessary (equipped with the
non-maintenance-free battery)
Timing belt: Check the wear and tension, and regulate or replace it, if necessary
★
Engine compartment bonnet hinge and lock: Lubricate them
★
★
★
Door hinge and limiter: Lubricate them
★
★
★
★
★
★
★
★
★
★
★
Spark plug: Check it, and replace it, if necessary
Air cleaner: Clean the housing, clear up the cleaner element, and replace the element, if necessary
★
A/C cleaner: Check the cleanness, and replace it, if necessary
Ignition timing: Check it
★
158
Repair and Maintenance
Mileage (Km)
Maintenance Item
5,000
15,000
Fuel cleaner: Replace it
30,000
★
Wedge-shaped belt: Check the tension, and regulate or replace it, if necessary
★
★
Transmission: Check the leakage or damage
★
★
Dust cap of constant velocity universal joint: Check whether or not it is damaged
★
★
★
Steering tie rod end: Check the clearance and whether or not the dust cap is damaged
★
★
★
Protective sleeve of steering universal joint assy.: Check the malposition or damage
★
★
Hand brake : Check its travel, and regulate it, if necessary
★
★
★
★
★
★
Brake lining /brake shoe: Check its thickness, and replace it, if necessary
Brake disc/brake drum: Check whether or not it works normally or is damaged, and replace it, if
necessary
★
Body bottom protector: Visually check whether or not it is damaged
★
Seat belt: Check whether or not it is damaged
★
★
Toe-in value, wheel camber angle: Check them, and replace them, if necessary
★
★
Ball pin: Check the clearance
★
★
Rear shaft rubber hinge: Check whether or not it is damaged
★
★
159
Repair and Maintenance
Mileage (Km)
Maintenance Item
5,000
15,000
30,000
Universal joint/front wheel bearing: Check whether the connection is loose, and the abnormal sound
★
Engine oil sump bolt: Check whether or not it is loosen, and tighten it, if necessary
★
Control arm rubber sleeve: Check whether or not it is damaged
★
★
Brake hose: Check whether or not it is aged or damaged
★
★
Brake pipe: Check whether or not it is damaged or corroded, and the leakage of all joints
★
★
★
★
Suspension components: Check whether or not they are abnormally loosen or damaged due to friction,
and whether or not they normally work
★
Joints for fuel system: Check the aging, damage, abnormal loose or friction
★
Exhaust system: Check the leakage and damage, and regulate or replace it, if necessary
★
★
★
★
★
★
★
★
★
★
Steering system: Check the level of power steering fluid, whether or not the clearance of gear rack of
steering wheel is proper, the connection status of all adapting parts, whether or not the system works
normally, and repair or replace it, if necessary
Cooling system: Check the level of anti-freeze fluid, check the status of all connection pipes, leakage,
and replace it, if necessary
Braking system: Check the level of brake fluid, check the status of all connection pipes, the leakage and
damage, the working condition of the system, and repair or replace it, if necessary
160
Repair and Maintenance
Mileage (Km)
Maintenance Item
A/C system: Check whether or not its pressure is normal, check the leakage, abnormal sound, abnormal
odor, and whether or not the system works normally
Tire (incl. spare tire) : Check the depth of tread, regulate the pressure of tire, and check the tightening
torque of wheel bolt
5,000
15,000
30,000
★
★
★
★
★
★
★
★
Tire: Change the position of tire
Chassis and body connecting bolt: Check whether it is loose, and tighten it, if necessary
★
★
★
Wheel: Check whether or not it is loose
★
★
★
★
★
★
★
★
★
Engine idle speed check: Check the working state of engine at the idle speed, whether or not the
parameters of electronic fuel injection system and the exhaust are normal, and regulate it, if necessary
Trial driving: Check whether or not the function of any mechanism is normal, and regulate it, if
necessary
Note: For manual transmission, replace the transmission gear oil once every one(1) year or 30,000 Km road mileage, and replace the
brake fluid once every two(2) year or 50,000 Km road mileage.
161
Repair and Maintenance
Chery
First 5,000Km
Maintenance
Card
(Within
six(6)
months as of purchase
date)
Special service station (stamp)
Vehicle Profile
Date: _______________
Owner: ___________________
Company (Name: _________________
Address: ________________________
Telephone: ________________________
E-Mail: _____________________
Purchase Date: ____________________
Purpose: ____________________
License plate number: ____________________
Mileage:
Chassis No
_______________
Model
Purpose: ___________
License
plate
number:
___________
Model Description
Engine No/Transmission No
Paint No/Interior Equipment
Optional
Special
(stamp)
service
Owner’s
____________
station
Signature:
162
Repair and Maintenance
Fist 5,000 Km Maintenance Card (Within six(6) months as of purchase
date)
Date: ____________ Mileage: ____________
Items to be checked:
Yes
No
Items to be checked:
Yes
No
1. Check the leakage of lubricating system,
□
□
11. Check the tension of generator and air
□
□
cooling system and fuel system.
conditioner belts, and regulate the tension, if
□
□
12. Check the engine compartment bonnet
□
□
13. Check the leakage of A/C system.
□
□
14. Check the leakage of the power steering
□
□
□
□
□
□
□
□
□
□
□
□
□
□
hinge and lock tongue.
3. Check the transmission oil level, color and
□
□
quality of oil, and refill it, if necessary.
4. Check the coolant level, and refill the
□
□
pipes, and refill the power steering fluid.
coolant or regulate the coolant concentration,
15. Check the installation and damage of the
if necessary.
dust cap for steering universal joint.
5. Check the leakage of transmission.
□
□
16. Check whether or not all gear positions of
6. Check the damage of the dust cap for
□
□
the manual transmission are shifted smoothly.
□
□
Date:_______________
Mileage: _______________
necessary.
2. Replace the engine oil and oil cleaner.
Fist 5,000 Km
Maintenance
Card
Purpose: ___________
License
plate
number:
___________
Special service station (stamp)
steering tie rod.
7. Check whether or not the dust cap for drive
shaft constant velocity universal joint is
17. Check whether or not the chassis and
body connecting bolt is loose.
damaged.
8. Check the leakage of brake fluid, and the
□
□
18. Check whether or not the seat belt works
□□
□□
19. Check the working state of engine at the
damage of brake pipe.
9. Check whether or not any brake wheel
normally.
cylinder works effectively.
idle speed, whether or not the parameters of
10. Check whether or not the tire inflation
electronic fuel injection system and the
pressure conforms to the specified value.
exhaust are normal.
20. Test the vehicle to check whether or not
the function of any mechanism is normal.
Owner’s
Signature:
___________
163
Repair and Maintenance
Maintenance Record
Regular Maintenance
Regular Maintenance
For 10,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available
For 20,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available
Date: ________________
Mileage: ______________
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Date: ________________
Mileage:_______________
Regular Maintenance
For 15,000Km of road
mileage or within six(6)
months after the last service,
the 15,000Km maintenance
items are available
Date: ________________
Mileage: _______________
Date: _______________
Mileage: _______________
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Date: ________________
Mileage: _______________
Date: _______________
Mileage: _______________
164
The regular maintenance is available in accordance with the items specified in the V325 vehicle regular technical maintenance service.
Repair and Maintenance
Regular Maintenance
Regular Maintenance
Regular Maintenance
For 25,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available.
For 30,000Km of road
mileage or within six(6)
months after the last service,
the 30,000Km maintenance
items are available
For 35,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available
Date: ________________
Mileage: _______________
Date: _______________
Mileage: _______________
Date: ________________
Mileage: _______________
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Date: ________________
Mileage: _____________
Date: _______________
Mileage: ______________
Date: ________________
Mileage: _______________
The regular maintenance is available in accordance with the items specified in the V525 vehicle regular technical
maintenance service.
165
Repair and Maintenance
Regular Maintenance
Regular Maintenance
Regular Maintenance
For 40,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available
For 45,000Km of road
mileage or within six(6)
months after the last service,
the 15,000Km maintenance
items are available
For 50,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available
Date: ________________
Mileage: _______________
Date: _______________
Mileage: _______________
Date: ________________
Mileage: _______________
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Date: ________________
Mileage: _____________
Date: _______________
Mileage: _______________
Date: ________________
Mileage: ______________
The regular maintenance is available in accordance with the items specified in the V525 vehicle regular technical
maintenance service.
166
Repair and Maintenance
Regular Maintenance
Regular Maintenance
Regular Maintenance
For 55,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available
For 60,000Km of road
mileage or within six(6)
months after the last service,
the 30,000Km maintenance
items are available
For 65,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available
Date: ________________
Mileage: _______________
Date: _______________
Mileage: _______________
Date: ________________
Mileage: _______________
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Date: ________________
Mileage: _____________
Date: _______________
Mileage: ______________
Date: ________________
Mileage: ______________
The regular maintenance is available in accordance with the items specified in the V525 vehicle regular technical
maintenance service.
167
Repair and Maintenance
Regular Maintenance
Regular Maintenance
Regular Maintenance
For 70,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available
For 75,000Km of road
mileage or within six(6)
months after the last service,
the 15,000Km maintenance
items are available
For 80,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available
Date: ________________
Mileage: _______________
Date: _______________
Mileage: _______________
Date: ________________
Mileage: _______________
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Date: ________________
Mileage: ______________
Date: _______________
Mileage: ______________
Date: ________________
Mileage: ______________
The regular maintenance is available in accordance with the items specified in the V525 vehicle regular technical
maintenance service.
168
Repair and Maintenance
Regular Maintenance
Regular Maintenance
Regular Maintenance
For 85,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available
For 90,000Km of road
mileage or within six(6)
months after the last service,
the 30,000Km maintenance
items are available
For 95,000Km of road
mileage or within six(6)
months after the last service,
the 5,000Km maintenance
items are available
Date: ________________
Mileage: _______________
Date: _______________
Mileage: _______________
Date: ________________
Mileage: _______________
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Service Station (Stamp)
Owner’s Signature
Date or mileage for next
service
Date: ________________
Mileage: ______________
Date: _______________
Mileage: ______________
Date: ________________
Mileage: _____________
The regular maintenance is available in accordance with the items specified in the V525 vehicle regular
technical maintenance service.
169
Quality Warranty Service
Safety
System
Protection
If your vehicle is equipped with
the air bag system, you must replace
the complete air bag system every
ten(10) years as of the purchase date,
and it must be replaced by the Chery’s
special service station.
To ensure the normal operation of
the air bag system, please get to the
Chery’s special service station to have
the air bag system replaced within the
specified time.
If the air bag system is replaced
before the specified time (e.g., after the
occurrence of an accident), please
carefully fill out the replacement record
for future reference.
Air
Bag
System
Replacement Record
Air
Bag
System
Replacement Record
†
†
†
†
†
†
†
†
†
†
†
†
†
†
†
†
Driver air bag
Passenger air bag
left-side air bag
Right-side air bag
Air bag control module
Air bag harness
Pretensioner seat belt
Other parts
Driver air bag
Passenger air bag
left-side air bag
Right-side air bag
Air bag control module
Air bag harness
Pretensioner seat belt
Other parts
1, ---------------------------2, ---------------------------3, ---------------------------4, ---------------------------5, ---------------------------6, ---------------------------
1, ---------------------------2, ---------------------------3, ---------------------------4, ---------------------------5, ---------------------------6, ---------------------------
Date: -----------------------Special Service Station
Stamp:
Date: -----------------------Special Service Station
Stamp:
170
Quality Warranty Service
Air
Bag
System
Replacement Record
Air
Bag
System
Replacement Record
Air
Bag
System
Replacement Record
†
†
†
†
†
†
†
†
†
†
†
†
†
†
†
†
z
z
z
z
z
z
z
z
Driver air bag
Passenger air bag
left-side air bag
Right-side air bag
Air bag control module
Air bag harness
Pretensioner seat belt
Other parts
Driver air bag
Passenger air bag
left-side air bag
Right-side air bag
Air bag control module
Air bag harness
Pretensioner seat belt
Other parts
1, ---------------------------2, ---------------------------3, ---------------------------4, ---------------------------5, ---------------------------6, ---------------------------
1, ---------------------------2, ---------------------------3, ---------------------------4, ---------------------------5, ---------------------------6, ---------------------------
Date: -----------------------Special Service Station
Stamp:
Date: -----------------------Special Service Station
Stamp:
Driver air bag
Passenger air bag
left-side air bag
Right-side air bag
Air bag control module
Air bag harness
Pretensioner seat belt
Other parts
1, ---------------------------2, ---------------------------3, ---------------------------4, ---------------------------5, ---------------------------6, ---------------------------
Date: -----------------------Special Service Station
Stamp:
171
Quality Warranty Service
Chapter 12
Quality Warranty Service
172
Quality Warranty Service
vehicle
Warranty
for
an
complete vehicle
is
or
fault(s) and they are covered by the
100,000Km accumulated road mileage,
quality warranty, please get to the
whichever comes first (i.e., one of the
Chery’s special service station to have
both conditions comes, the vehicle isn’t
your vehicle examined and repaired.
twelve(12)
months
Any V525 vehicle sold by a
subject to the quality warranty), and the
authorized sales service center can
warranty period is calculated starting
enjoy the conditional quality warranty.
from the earliest among the date that
Within the warranty, if the quality fault
the owner receives the vehicle, the
of the vehicle occurs in case of the
owner information upload date, the
normal operation and maintenance, it is
invoice date of purchasing, and license
covered by the warranty, and the owner
receiving date. If the purpose of vehicle
12 months or 40,000 Km warranty
does not pay for the maintenance and
changes within the warranty period, the
for the oxygen sensor, injection nozzle,
repair. However, the vehicle must be
warranty
clutch plate, damper, damper rubber
repaired by the Chery’s special service
concerned doesn’t alter.
station.
duration
and
mileage
sleeve, dust cap, supporting block,
Within the warranty period, if
The quality warranty period for the
the vehicle is subject to regular
non-operational
maintenance
V525
vehicle
is
according
to
the
thirty-six(36) months or 60,000Km
requirements specified by the Chery
accumulated road mileage while the
Automobile
warranty period for the operational
complete vehicle or some parts have
Co.,
Ltd.
Quality
warranty
period of special parts
(limited to the original
quality problems only):
while
the
engine
timing
belt,
brake
disc,
tensioner pulley, and tensioner.
6 months or 30,000 Km warranty
for horn.
12 months or 60,000 Km warranty
for the generator belt.
173
Quality Warranty Service
12 months or 20,000 Km warranty
for the plastic parts, rubber parts,
switches, and lamps.
Quality warranty period of
the wearing parts (limited
to the original quality
problems only)
The quality warranty period of the
wearing parts is three(3) months or
5,000Km.
The wearing parts include: Bulb,
glass products, air cleaner element, fuel
cleaner, oil cleaner, wiper blade, tire,
clutch lining, brake shoe, spark plug,
high-voltage cable, and battery.
Parts not covered by the Warranty:
The
normal
consumption
of
lubricating oil (grease), brake fluid,
low power battery, engine coolant,
power steering fluid, engine oil and
etc., fuse.
Note: For the warranty period for the
wearing parts and special parts, it is
calculated on the duration and
mileage, whichever comes first. The
warranty period of the other parts is
the same as that of the complete
vehicle.
174
Capacity and Specification Parameters
„
Coverage of the warranty
Comply with the regulations specified in this instruction manual toe use, repair and maintain your vehicle. And bring this manual
that can prove your vehicle has been regularly examined and repaired.
The quality defects and damages caused by product design, manufacturing, assembly, raw material defect and other factors
If an owner reclaims the quality warranty, he/she shall protect the original status of the damaged parts in order to clarify what truly
happened.
The replacement and repair for parts within warranty period will not extend the warranty period for complete vehicle or
parts. The removed parts within warranty periodare subject to the Chery Automobile Co., Ltd..Items not covered by the
Warranty
1. The following faults are not covered by the Quality Warranty:
1) Faults occurred in the vehicle which is repaired or maintained by the owner himself/herself or by the service station other than
Chery’s special service stations.
2) The Chery Company will not be responsible for any direct or indirect damage caused due to the installed parts and components
not produced or provided by the Chery Automobile Co., Ltd.
Hint: To ensure the proper operating condition of this vehicle, the owner shall use the parts and components (genuine spare parts)
provided by the Chery Automobile Co., Ltd. and the Chery’s special service station will offer you the genuine spare parts
purchasing service.
3) The Chery Company will not be responsible for any direct or indirect damage caused due to the refitting or additional
installation of various equipment by the owner himself/herself, especially the reftting or additional installation of such system
175
Capacity and Specification Parameters
involving the product safety as electrical, braking, steering and other systems.
4) Faults caused due to no routine examination or regular maintenance conducted as required, or the examination, repaired and
maintenance conducted by the service station other than the Chery’s special service station.
Hint: To ensure the proper operating condition of this vehicle, the owner has the responsibility to conduct the necessary
examination, repair and maintenance. For example, the engine oil
has the crucial functions such as lubricating, cooling the engine, rust prevention and etc.
176
Capacity and Specification Parameters
The engine oil in service will be gradually contaminated, corroded or degenerated. So if you still continue to use such engine oil
for a long time, it may burn out the engine. And for this kind of fault caused due to the shortage of proper examination and
maintenance, the Chery Company will not be liable for the warranty service.
This instruction manual specifies the necessary maintenance items. After such items are executed, please record the results
in this instruction manual, and keep it carefully. When accepting warranty service, you must bring forth this instruction manual.
5) Severe failures result from the problems that owner should have discovered and handled, but ignored. Hint: For example,
during the routine inspection, it has been found that engine oil warning light gives an alarm, or the driver feels something abnormal
(noise, vibration) while the vehicle has not been overhauled in time and continues in service till severe failure occurs.
6) Faults caused due to the use of products other than the genuine spare parts and specified grease (including engine oil, brake
fluid, transmission oil, and fuel).
Hint: The prerequisite for this warranty is to properly use the genuine spare parts and specified grease so as to ensure the
normal operating of the vehicle. So, if the non-genuine spare parts is used, or they are genuine spare parts but not applicable to this
vehicle, or the grease not specified in the instruction manual is employed, all of these may make an influence on the vehicle's
original performance and decrease its durability.
For example, the oil cleaner not specified by Chery Company is utilized and then it result the cleaner jammed and the bearing
burnt.
7) Faults caused due to the malfunction of the vehicle and improper use of the Instruction Manual or due to the overuse of the
vehicle that exceeds the vehicle’s capabilities specified in the specification (the vehicle travels as a racing vehicle with the
overload, the engine overload, excessive loading capacity, passenger overload, excessive driving speed, etc).
Hint: The malfunction of the vehicle and improper use of the Instruction Manual or due to the overuse of the vehicle that exceeds
the vehicle’s capabilities specified in the specification are mainly as follows:
For example:
◆
◆
◆
Faults caused due to driving at harsh area or racing.
Overloading or excessively pressing chassis spring.
Engine failure caused due to the operation with overload, and the excess of the transmission limit specified in the Instruction
Manual when the vehicle travels at high speed.
2. The following symptoms cannot be deemed as faults, without the warranty.
177
Capacity and Specification Parameters
1) The symptoms caused due to the wear or the long period of service time. (Natural fading or degeneration of painted surface,
plating surface, resin parts and etc.)
Hint: Among the parts consisting of an automobile, some of them (such as clutch disc) are subject to be continuously worn
with the driving and repeated operating.
In addition, the brake lining and
other parts which implement its function by wearing itself, those consumptive parts for daily running, and the grease such as
engine oil or cooling water which plays the role of lubricating and cooling function, will be substantially consumed and
degenerated with the traveling of vehicle. The paint surface of exterior plate and the interior instrument panel surface would
gradually tarnish and slowly fade.
The consumption generated due to daily running and operating as well as the fading symptom will not be covered by the Warranty.
2) In general, those perceived occurrences that will not affect the vehicle quality and functions. (the operation feel, noise and etc)
Hint: Noise and vibration sometimes are caused by abnormal vehicle's condition while it is possible that normal operation
also causes noise and vibration occasionally. In this case, the vehicle's quality and function have no problem. For instance, the
178
Capacity and Specification Parameters
noise caused when the brake pedal is stepped on mostly comes from friction (usually called the braking noise) while it is not the
functional problem.
3. The following faults caused due to the exterior reasons are not the material and manufacturing problems, without the
warranty.
1). Faults caused due to the exterior reasons such as coal smoke, medicine, bird droppings, oil, acid rain, gravel, scrap iron, ash
falls, salt and etc.
Hint: Faults caused due to the exterior reasons such as glass broken by splashing gravels during traveling, compartment
scratched, paintwork fading resulted due to the bird dropping or acid rain attaching.
2) Faults caused due to the natural disaster such as earthquake, strong wind, flood and fire or other accidents.
4, The Chery Company will not be liable for the expenditures in case of the following conditions:
1) Some parts of the vehicle are the wearing parts, such as: friction lining, wiper blade, spark plug, cleaner, tire, bulb, lubricating
oil (grease), brake fluid, low power battery, engine coolant, power steering fluid, oil. The costs generated due to the normal
consumption of these parts and the expenditures caused by the replacement and supplement of grease or oil.
Hint: The wearing parts and grease will be consumed and degenerated along with daily driving. Owners themselves pay
for the cost for such kind of products' replacement and supplement.
2) Expenditure for the overhaul and regular replacement of parts and components specified by the Chery Company.
(Except for the items which its first inspection cost is for free)
Hint: The consumption and degeneration will be inevitable during the course of the use of the vehicle. So, the proper
overhaul and daily/regular inspection must be done on schedule according to the service condition.
3) Expenditure for your vehicle repaired in the other service station other than the Chery’s special service station.
The Chery Company will not pay for repair in the other service station other than the Chery’s special service station.
4) The expenditure generated by normal inspection and adjustment (fuel consumption, CO content, lighting, inspection and
adjustment of four-wheel calibrating mechanism, dynamic balance of tires, and etc.).
5. Additional Expenditure
The economic loss or additional expenditure caused due to the vehicle failure to be employed is not covered by the quality
warranty. For instance, it includes:
z The economic loss and time loss caused due to the vehicle failure to be used
179
Capacity and Specification Parameters
z The expenditure for the storage of the vehicle
z The expenditure for the rent or lease of the vehicle
z The expenditure for the accommodation, food or other items
z Other related loss
Spare parts warranty
180
Capacity and Specification Parameters
181
Capacity and Specification Parameters
182
Capacity and Specification Parameters
Chapter 13
Capacity and Specification Parameters
Vehicle Identification
Description
183
Capacity and Specification Parameters
Engine Number
The engine number of Chery V525
VIN
The VIN code of Chery V525 vehicle
vehicle is located on the top of cylinder
body at the exhaust side of engine, as
shown in the figure above.
is printed on the side surface of
wheelhouse behind the expansion tank.
(As shown in the figure above) .
184
Capacity and Specification Parameters
Vehicle Profile Plate
If it is difficult to buy the high quality
fuel with additives or when the engine
has such faults as start difficult,
The unleaded gasoline of below 93#
unstable idle speed, power down and
grade is unavailable to be used.
etc, the proper additives shall be added
Otherwise, it may damage the engine,
in case of refueling. The fuel additives
without the warranty.
can prevent the engine from corrosion
The vehicle profile plate of Chery
V525 vehicle is located at the rear right
side of front grille (shown in the figure
above).
and encrustation and clean the fuel
system.
The Chery’s special service station has
Chery Company, and the operators in
the station are familiar with the use of
Fuel tank capacity:
the
Gasoline engine: 61 L
encrustation treatment method, and
The high quality fuel with the fuel
grade below and detergent and other
additives
The vehicle equipped with the catalytic
converter uses the unleaded gasoline
only.
the fuel additives authorized by the
Fuel
93# or above unleaded gasoline
(octane value: 93 or above)
and
the
engine
offer you the best service with all our
To prevent the event that the improper
grade of gasoline is refueled,the fuel
tank adopts the constriction type filler
opening design. Only the fuel gun for
the unleaded gasoline can insert into
the filler opening.
heart.
additives is available only. The low
The fizzle sound can be heard when the
grade of fuel may damage the engine.
filler cap opens. This is a normal
phenomenon.
185
Capacity and Specification Parameters
Please DO NOT use the
additives or engine treating
compound unauthorized by
the Chery Company. These additives
are not only unnecessary, but also
may damage the engine in certain
cases, without the warranty.
If you by accident refuel the
leaded gasoline into the fuel
tank , DO NOT start the
engine (even if a few of leaded
gasoline is refueled only). Otherwise,
the lead contained in the fuel will
cause the permanent damage of the
catalytic
converter.
It
is
recommended
to
immediately
contact the nearest Chery’s special
service station.
SAE 10W/30 engine oil. Your vehicle’s
engine is designated to use this kind of
engine
oil.
To
obtain
the
best
performance, please use the gasoline
according
to
this
provision
of
Please DO NOT use the
engine oil which doesn’t
conform
to
the
specifications and requirements
above. The improper engine oil may
damage the engine, without the
warranty.
regulation.
Refill the engine oil
Vehicle Fluids
The Chery’s special service station will
records and use
Please replace the fluids according to
the recommended engine oil. The
the time interval specified in the
refilled oil shall be below the MAX
Maintenance Manual.
keep the oil-change
mark on the dipstick.
Transmission oil
For the detailed recommendations or
Engine oil
information are required, the Chery’s
Automatic transmission
special service station will be pleased
Replace the engine oil
to help you.
The automatic transmission oil shall be
ATF SP3 synthetic gear oil,with the
capacity of 6.5L. The other additives
are unallowable to be added into the
lubricating oil.
The model of engine oil model
recommended by the Chery Company
is:
186
Capacity and Specification Parameters
Power steering oil
The hydraulic oil conforming to the
Chery’s specifications is available. The
Chery’s special service station has the
Chery’s original fluids.
and brake fluid at the same time.
Ensure that the brake fluid must be
clean when the fluid is refilled. The
entrance of any foreign material into
the brake system may result the
deprivation of braking performance.
The Dot 4 brake fluid is available.
the Chery’s specifications. The Chery’s
Refill to the MAX mark as required.
special service station has the Chery’s
The brake fluid without paraffin is
original fluids.
up
for winter.
the
to
the
instructions
on
the
container.
DO NOT dispose the empty/waste oil
container and cleaner as the household
waste. Please use the local authorized
Windscreen cleaning fluid
Fill
low, use the windscreen cleaning fluid
refer
Please use the coolant conforming to
In case of heavy load (such as
it tows a tail vehicle, travels
on the mountain road fro a
long time), replace the brake lining
Company. If the exterior temperature is
For the proper concentration, please
Coolant
Brake fluid and clutch oil
available only.
and water (1:20) specified by Chery
reservoir
with
waste disposal facilities.
the
concentrated windscreen cleaning fluid
187
Capacity and Specification Parameters
Weight
Please stick to the load
specified in the Manual (if
applicable). DO NOT exceed
the allowable gross weight, otherwise
it may result the change of braking
and manipulating performance, and
cause an accident.
tools, spare wheel and the driver’s
The payload is the subtraction of the
Capacity (L)
kerb weight from the allowable gross
weight.
Engine oil
4.0L±0.5 L
(Including
the
case of travel, including the coolant,
Automatic
lubricating oil, fuel tank up to 90%,
Transmission
Power
payload.
6.5L
assisted
steering
Cooling system
Windscreen cleaning
system
Fuel Tank
Brake fluid/clutch oil
reservoir
The optional fittings and subsequent
additional equipment will reduce the
cleaner)
The kerb weight means the weight in
Mass Parameters
weight (75 Kg).
MAX mark
7.5L
MAX mark
61L
MAX mark
188
Capacity and Specification Parameters
Model
SQR6470
Complete vehicle kerb mass
Complete
vehicle
kerb axle-load mass
kg
1505
Front axle
kg
882
Rear axle
kg
623
Maximum manufacturer's laden mass
(passenger inclusive)
kg
Maximum manufacturer's total mass
kg
Axle-load mass at Front axle kg
maximum
manufacturer's total Rear axle kg
mass
Maximum
Front axle kg
allowable
manufacturer’s
Rear axle kg
axle-load mass
Number of passenger (driver inclusive)
person
525
2030
1006
1024
1150
1200
7
189
Capacity and Specification Parameters
y
Wheel and Tire
The value of pressure listed in the table above is suitable
for the cold-state tire. The pressure will increase
somewhat after it is heated, but it is unnecessary to
Tire pressure
reduce the pressure.
Before your journey begins, check the tire pressure (cold state)
y
(DO NOT forget to check the pressure of spare tire).
Tire
Front
Wheel
Rear
Wheel
No-load/hal
f-load
Full load
No-load/hal
f-load
Full load
Tire
Pressure
(kPa)
in the table above shall increase by 20Kpa.
y
Tire pressure (cold tire) (kPa)
Spare
tire
If the winter tire is available, the value of pressure listed
To offer you the convenience to search the specified
value of inflation pressure, there is a self-adhesive label
attached to the inner side of fuel filler cover, which
indicates the specified value of tire pressure.
210
220
Tightening torque of wheel bolt
250
220
230
The tightening torque of wheel bolt is 110±10 Nm.
Wheel
Tire
Wheel Rim
Precautions on tire pressure
y
Check the tire pressure at least once every a month,
205/55R16×91W
6J×16
especially when the vehicle travels at high speed.
190
Capacity and Specification Parameters
Engine Information
Model
4G64S4M
Vertical four-cylinder, four-stroke, water cooling, overhead camshaft, 16 valves,
transverse mounted, and multipoint sequence injection
Type
Cylinder Diameter
mm
86.5
Piston Travel
mm
100
Displacement
ml
2,350
Compression Ratio
9
Rated power (net power)
kW
95
Rated RPM r/min
5,500
Max. Torque
N.m
198
Max. Speed r/min
3,000
Min. Fuel Consumption
g/kw.h
260
** The adjustment or check begins only more than 5 minutes after the engine stops operating.
191
Capacity and Specification Parameters
Vehicle Dimension
192
Capacity and Specification Parameters
Item
Dimension (mm)
A=Length (Max.)
4662
B=Width
1820
C=Height (Kerb Weight)
1590
D=Wheel Base
2800
E=Wheel
Tread
Front
1550
Rear
1535
Ground Clearance (at fuel tank)
≥125
193
Automobile Product Defect Report Guide
Chapter 14
Automobile Product Defect Report Guide
195
Automobile Product Defect Report Guide
z
What’s defect?
According to China Defect
Automobile Product Recall Regulation
(hereinafter referred to as “the
Regulation”), the “defect” product to
be recalled has the following three
conditions:
‹ threat to the safety of human life
and properties, and unconformable to
the technical laws and regulations and
national standards related to the safety
of vehicle;
‹ with the identity, i.e., the defect
universally exists in the a certain batch,
model or catalog of products and it
isn’t a individual case;
‹ caused due to the design,
manufacturing and other reasons. The
fault created due to the improper use
and maintenance is not a defect.
z What’s recall?
Recall means the process to
eliminate the product defect, which
may cause the personal injury and
property loss, by the defect automobile
manufacturer (including importer)
selecting the repair, replacement,
recovery and other methods in
accordance with the procedures
required in the Regulation.
z
What are the principles
to
determine
the
automobile
product
defect?
‹ The product which the safety
performance doesn’t conform to the
technical laws and regulations and
national standards related to the safety
of vehicle after it is inspected by the
inspection institution (with the
qualification certificate approved by
China
executive
mechanisms
concerned);
‹ The product which already cause
the damage of human life and
properties due to the defect of design
and manufacturing;
‹ The product which its defect sill
cause the damage of human life and
properties in case of special condition
after the vehicle is tested, experimented
or demonstrated, although it doesn’t
result the damage of human life and
properties of owner or other persons.
z What defect may make
an influence on the safety?
The form of defects which make an
influence on the safety is very complex
Samples below:
‹ The steering system component
may break suddenly, which causes the
vehicle is partly or fully out of control;
‹ The braking performance fully or
partly miss;
‹ The fuel system component failure,
and, in particular, it may result the fuel
leakage and fire disaster when
impacting;
‹ Unreasonable tire design or
structure may result the tire blows out
and the vehicle is out of control;
‹ The wheel may break or get loose,
which result the vehicle is out of
control;
‹ The accelerator pedal control
mechanism may break or is clamped;
‹ The engine fuel or ignition switch
failure may cause the engine to
extinguish or the fire disaster;
‹ The engine cooling fan blade may
break suddenly, which makes the
professional other people injured;
‹ The windscreen wiper arm may
196
Automobile Product Defect Report Guide
fall down during working;
‹ The seat or seat backrest catch
some sudden troubles during the
vehicle is traveling;
‹ The key components may break
suddenly or fall down, which result the
vehicle is out of control or the
professional or other people is injured;
‹ The circuit system failure may
result the fire disaster or the lamp not
light;
‹ The jack or lifter may break down,
which result the death or injury of
operator;
‹ The air bag swells in the case that
it shall not swell.
For the other vehicle quality
problems apart from the safety defect,
the State encourage the manufacturers
to recall these fault vehicles according
to the procedures provided in the
Regulation. In general, the following
fault can’t be considered as a safety
defect:
— Audio system failure;
— Paint quality or garnish blemish.
z
Report and Complaint
According to the related provision of
the Regulation, the owner has the right
to complain or reflect the defect of
automobile
product
to
the
administrative departments in charge
and operators concerned, and submit
the recommendation, which the related
investigation on the defect product
recall
is
developed,
to
the
administrative departments in charge.
The “problems” reflected by the
owners are the important clues which
are used by the administrative
departments in charge and vehicle
manufacturers to determine whether the
vehicle has defect(s). So, If you find
that the vehicle may have defect(s),
you shall actively complain or report it.
‹ Immediately report the details of a
problem to the Defect Product
Management Center of the General
Administration of Quality Supervision,
Inspection and Quarantine of P. R. of
China, and search whether the
manufacturer has already implemented
the recall of the defect product. For
more information, please contact:
URL: www.qiche365.org.cn
E-mail: zhaohui@qiche365.org.cn
Telephone: 86+10 6553 7365
Fax: 86+10 6552 7365
Address: Room 1061, Xinzhong
Building, N0 2, Xinzhong West Street,
Dongcheng District (100027), Beijing,
China.
‹ Apart from reporting to the Defect
Product Management Center, the owner
also shall report this problem to the
vehicle manufacturer concerned. For
the specific contact method, see the
attached documents of the vehicle
manufacturer.
z
Report
(Complaint)
Preparation
‹ Certificate number
The certificate umber of the
complainant is very important when the
identity of owner and the recall
notification are determined. Please
provide the certificate number of the
owner when sends the complaint. The
requirements to fill out the number are
as follows:
9
If the owner is a natural person,
fill out the number of ID card or
passport in the Certificate
Number column;
9 If the owner is an enterprise or
institution, fill out the code of the
enterprise or institution or the
code
of
legal
person
197
Automobile Product Defect Report Guide
(organization code).
‹ VIN
VIN is the abbreviation of
Vehicle Identification Number. It is a
group of characters given in order to
identify a vehicle. The VIN has become
the unique “ID Card” to identify a
vehicle worldwide.
The VIN of a vehicle includes the
vehicle’s manufacturer, production date,
model, type of body, and the detailed
information of engine and other
equipment. With the VIN, it is very
convenient to determine the vehicle’s
production
lot
and
its
main
configuration.
To
enable
the
government’s
administrative
departments in charge and the vehicle
manufacturer to rapidly find the defect,
the owner must provide an accurate
VIN when he/she complains.
In general, the owner can find out
the VIN from the following positions:
9
the left (right) front side of the
instrument panel, under the
windscreen;
9
the “frame number” registered in
the Driving Permit for the Motor
Vehicle, which is generally VIN;
9
the body number plate, such as
some number plates in the engine
compartment.
Reminder: If you find that the
vehicle may have defect, please
fill out the form below, and
then mail to the Defect Product
Management Center according
to the address provided in the
“Report and Complaint” above.
198
Automobile Product Defect Report Guide
The owner’s Report on Automobile Product Defect
(The copied form is as valid)
1. Owner information
Name
(Enterprise
Name)
Certificate
Number
Contact
Person※
Address
Postal Code
E-mail
Telephone
Fax
Note: If the owner is a natural person, fill out the number of ID card or passport in the Certificate Number
column; and if the owner is an enterprise or institution, fill out the code of the enterprise or institution or the
code of legal person.
199
Automobile Product Defect Report Guide
2. Vehicle information
Make of Vehicle
Type
Year
Model
Engine No
Frame No
VIN Code
Type of
Vehicle※
Type of Body※
Production Date
Purchase Date
A.Yes
B.No
Engine
Displacement※
Second-Hand
Vehicle?
Number of
cylinders※
Type of Drive※
With ABS? ※
A.Yes
B.No
Road Mileage※
Type of Seat
Type of Air
Belt ※
Bag※
Note: ※ Not filled out.
Type of Body means: two-door, four-door, station wagon, goods vehicle, van and etc.
200
Automobile Product Defect Report Guide
Type of Drive means: front-wheel drive, rear-wheel drive, or four-wheel drive.
3. Vendor information
Enterprise
Name
Address
Year
Postal Code
Telephone
E-mail
Fax
4. Defect description
The system in which the defect exists (such as: braking system, steering system and etc) and
description concerned:
5. Status when the defect is found
Date:
Road Mileage:
Speed:
Others:
201
Automobile Product Defect Report Guide
6. Whether or not you contact the manufacturer or the State’s administrative department in charge of
the recall of defect product:
A.Yes
B.No
7. Traffic accident description
Whether or not the collision or fire occurs:
Which air bag it explodes:
Number of Injuries and Deaths:
Estimated direct economic loss:
Others:
8. Tire problem description (if applicable):
The Owner (Stamp)
Date
202
Emergency Maintenance Guide
z
Defect Report Description
To enable your defect report to be quickly handled, it is recommended that the owner complains online via the network (refer
to the “Report and Complaint” in this guide). The items of online complaint are the same as those of the complaint filed through
correspondence, and the effect gained is also the same. The details of complaint form are described as follows:
‹ Owner information
﹡Name, telephone, address and other items must be accurately filled out. These information will be used as the important basis of
the recall notification;
﹡If the owner is an enterprise or institution, fill out the code of the enterprise or institution or the code of legal person
(organization code).
‹ Vehicle information
﹡Fill out in detail the Make of Vehicle, Model, VIN(Frame Number), Engine No and Production Date. The related information
can be found from the vehicle nameplate and vehicle certificate and other materials;
﹡If it is a second-hand vehicle, it shall be stated;
﹡The items indicated with the symbol “※” may not be filled out.
‹ Defect description
﹡State in detail the fault of the vehicle, and provide the service station with the method to remove the fault.
﹡Provide the “List of Items to Be Repaired” or photos to additionally state the fault, if necessary.
﹡If you know that the fault ever occurred on the other vehicles (e.g., you found the fault vehicle in some one service station or
you know the information via the other channel), it is recommended to provide the related information.
z
Frequently Asked Questions
‹ Whether the automobile recall means the “rejection”?
The automobile recall is unequal to rejection.
The automobile recall means the process to eliminate the product defect, which may cause the personal
injury and property loss, by the defect automobile manufacturer (including importer) selecting the repair,
replacement, recovery and other methods in accordance with the procedures required in the Regulation.
203
Emergency Maintenance Guide
So, the automobile recall is unequal to rejection. Just the reverse, viewing from the overseas experience, a majority of recall
can be solved using the methods such as the repair for free or parts and components replacement and etc.
When it is found that the product needs to be recalled, the manufacturer concerned will establish the technical solution to
eliminate the defect according to the specific condition of the defect. In general, the problem can be solved using the repair or
parts replacement, and the complete vehicle recall is a rare event. To encourage the manufacturer to actively remove the safety
defect and guarantee the security of the whole society, all of owners shall objectively, rationally consider any recall of vehicle,
and get to the service station specified by the manufacturer to have your vehicle repaired for free A.S.A.P. after you receive the
recall notification or see the announcement.
‹ Is the quality of product from the manufacturer which is conducting the automobile recall poor?
Not think so.
An automobile is a very complex product, which involves thousands of parts and components. What’s more, these parts and
components are produced by hundreds of factories concerned, and the service environments of automobiles are different. Although
any automobile manufacture has the very strict quality control system and also throws a lot of human resources and capitals, some
problems to interfere with safety occur inevitably during the design and manufacturing. For instance: the unreasonable
arrangement of pipeline or circuit may result the interference or wear during the course of motion, the low or over-high ambient
temperature may cause the poor working of valve or the breakage of shaft, the sensor failure may result the sudden extinguish of
the engine, tire failure and etc. So, it is difficult to avoid that a few of vehicles have somewhat safety defect, and, in general, it has
no inevitable relation with the automobile manufacturing level and the product quality. The defect can be magnificently removed
and the safety of owner and society can be guaranteed as long as the manufacture finds the defect in time and then take some
measures to recall the vehicles concerned.
The products are immediately recalled when the product defect is found. It is the representation of a manufacturer responsible
for the products and customers, and the credit and strength of the manufacture.
On the basis of the analysis on a majority of recall records of other nations and regions, it is found that almost all of
automobile manufacturers issue some recall announcements every year. Some are the worldwide well-known automobile
manufacturers. But, these automobiles still are highly appraised and selected by many customers who don’t doubt the quality of
these products.
‹ What shall I do when I find the automobile has quality problem?
204
Emergency Maintenance Guide
The “problems” reflected by the owners are the important clues which are used by the administrative departments in charge
and vehicle manufacturers to determine whether the vehicle has defect(s). So, If you find that the vehicle may have safety defect(s),
you shall take the following measures:
1) Get to the service station specified by the manufacturer A.S.A.P. to have the vehicle diagnosed and repaired.
2) Immediately report the details of this problem to the Defect Product Management Center of the General Administration of
Quality Supervision, Inspection and Quarantine of P. R. of China (refer to “Report and Complaint”), and search whether the
manufacturer has already implemented the recall of the defect product.
3) Apart from reporting to the Defect Product Management Center, the owner also shall report this problem to the vehicle
manufacturer concerned.
4) If this model of vehicle is being recalled, you shall drive your vehicle to the location specified by the manufacturer A.S.A.P,
and then the manufacturer will eliminate the defect for free according to the specific condition of the problem.
‹ Can I require the manufacture to recall my automobile if it has some problems?
According to the Regulation, the “defect” means the unreasonable hazard which may endanger the safety of human life and
properties, due to the design, manufacturing and other reasons, and universally exists in some one batch, model or catalog of
automobile products, with the identity, or the case that the products don’t conform to the national standards related to the safety of
vehicle.
It is observed that one of important factors which makes an influence on the recall is the “universality” of problem. So, if
only one vehicle has the quality problem which may make an influence on the safety, it is difficult to determine whether the vehicle
is within the recall range.
However, when the owner meets this kind of problem, he/she shall actively complain it to the Defect Product Management
Center and the manufacturer concerned, and provide them with the details of the problem. We actively complain, and then the
State’s administrative departments in charge and the automobile manufactures determines whether there is the “universal” defect
according to a majority of complaint information. In this case, it can be determined A.S.A.P. whether the automobiles shall be
recalled to guarantee the owner’s benefit and the public safety.
So, the automobile recall requires your active participation and the whole society’s cooperation. In addition, please fill out your
detailed, accurate contact method when complaint in order to notify you in time when the recall begins!
205
Emergency Maintenance Guide
Chapter 15
Emergency Maintenance Guide
206
Emergency Maintenance Guide
Emergency Maintenance Guide
Model:
First Emergency Contact Person:
License Plate Number:
Second Emergency Contact Person:
Name of Owner:
Insurance Company:
Address of Owner:
Telephone of Traffic Police:
Telephone:
Name of Chery’s special service station:
Blood Type:
Telephone of Chery’s special service station:
207
Emergency Maintenance Guide
First Vehicle Concerned
Make of Vehicle ___________ Color _____________
License Plate Number_____________
Driver Name _____________
Driver Address _______________________________________________ Driver Phone ________________
Driver’s Insurance
Owner’s Detailed Information (if different)
Witness
Traffic Police
Name _____________________
Number of ID card of police on site
Address ___________________
Any statement or not?
Victim
Name ____________________
Does any driver receive the warning sheet or traffic ticket?
Address __________________
208
Emergency Maintenance Guide
y
Travel direction and speed
y
Slip traces
y
Where does the witness live?
y
Road name and its width, curvature
and gradient
y
What direction is the North?
y
Any barrier within the reach of
eyesight
Status (Delete as appropriate)
y
Weather: Dry/moist/rainy/snow/ice
y
Visibility: good/obscurant/foggy/snow
y
Road
surface:
Dry/wet/grease/mud/ice/snow
Sketch
The position of vehicle before and after an accident occurs
y To Record
y Traffic movement: Few
vehicles/normal/crowd
209
Emergency Maintenance Guide
General
moment when an accident happens. For
reasons, and, here, some reasons are
the sake of safety, why not take some
listed below:
times to read it carefully so as to save
Under the crowded road and disordered
your precious rescue time while you
Professional Knowledge
traffic conditions, the ratio of traffic
catch a traffic accident.
Who can know the Chery automobile
If your Chery vehicle is damaged
more than the Chery’s special service
accidentally and you want to have it
station? There are the comprehensive
repaired as soon as possible, the best
and
choice is to get to the Chery’s special
techniques and knowledge in the
service station.
Chery’s special service station, which
accident occurrence is considerably
high. However, the quantity of serious
injured has decreased greatly due to the
use of seat belt during driving. No
matter how care you are, it is always
possible to catch a traffic accident. The
inconvenience resulted in numerous
accidents is even mush worse than the
injured. In this case, only few people
know how to do. This is the reason why
we shall compile this chapter. We hope
you are not required to read this
chapter at all times. But, if required,
you will find it is extremely useful.
Please remember that it is now that you
read this manual, other than the
professional
maintenance
are able to ensure the maintenance
Make the best of your
the Chery’s special
service station
process
conforms
to
the
Chery’s
If your Chery vehicle is damaged due
maintenance can get the best protective
to a traffic accident and required to be
effect, and the service station can
repaired, the best is to give it to the
implement the Chery’s warranty work
Chery’s special service station. This is
(if this item is suitable for your
because there are many convincing
vehicle).
standards. The Chery’s special service
station combines the service and the
maintenance process to ensure the body
210
Emergency Maintenance Guide
Quick
acquisition
Chery’s genuine parts
of
High-quality maintenance
Each Chery’s special service station is
implements the paint repair, they will
make the color of paint the same as the
original one. Meanwhile, you will find
There are a great number and various
equipped with the special clamps and
models of Chery’s genuine parts in
tools for the body to ensure the
your Chery’s special service station,
accuracy
which can reduce the time of waiting
maintenance items and make your
for genuine parts during maintaining. If
vehicle
there are no stock parts, you can also
completion of the maintenance, without
order them directly from the Chery
the worry about the turn characteristics
Company, and the ordered parts will be
abnormal or the tire over-worn. What’s
Your Chery’s special service station is a
quickly delivered to you. The Chery’s
more,
mechanical
local reputable company. This is the
special service station utilizes the
maintenances conducted by the Chery’s
reason why the body maintenance
replacement parts certificated by Chery
special service station are accompanied
conducted by the Chery’s special
Company, the quality of which is
by the life warranty, which is a much
service station can get a full warranty.
warranted by the Chery Company and
favorable for our customers.
requirement
operate
a
of
safely
majority
of
major
after
the
the same as the high quality of original
that the Chery’s special service station
can be able to handle the multi-painted
baking paint into the durable high
luster finish.
Full warranty
Antirust treatment
parts of your vehicle. It is difficult to
Professional paint repair
The comprehensive and strict antirust
guarantee the quality of maintenance if
It is surely that you must not like a
treatment is applicable for any new
the non-genuine parts are used..
vehicle with two colors. When the staff
Chery
of the Chery’s special service station
manufacturing, including the special
automobile
during
211
Emergency Maintenance Guide
bottom protection and the waxing
hopes you to get to the service station
treatment of the positions sealed. The
for the maintenance and replacement of
staffs of the Chery’s special service
parts and accessories other than the
station have taken the complete series
body maintenance after
of antirust treatment training. They
Even when you change a new Chery
have
and
vehicle, your Chery’s special service
equipment, which ensures that the
station still can offer multiple services,
antirust treatment can be updated after
apart from the body maintenance. We
the
hope you to make a good use of this
the
proper
completion
materials
of
the
body
maintenance to make your Chery
guidance to take the first-aid measures.
y
traffic accident and your action
an accident.
may rescue a person’s life. The
best preferential thing is to ensure
your own safety and protect the
site.
y
Take action quickly, but keep
your head.
service.
vehicle still like a new one several
You may be the first witness of a
y
Completely stop the vehicle, turn
years later.
First aid
Your
Chery’s
special
service station hopes to
meet you again!
Every Chery vehicle is equipped with a
driver should be required to have basic
y
Turn off all on-vehicle switches.
Finally, The best action that you trust
first-aid knowledge. The best way to
y
Keep everyone no smoking to
your Chery’s special service station is
gain this kind of knowledge is to attend
to make your Chery’s special service
the first-aid training courses held by the
station meet you again. It means that
first-aid organization. However, the
your Chery’s special service station
following precautions are the main
on the hazard warning flasher
light to give an alarm to the
passing vehicle.
first-aid kit onboard. Meanwhile, any
avoid firing the splashed gasoline.
212
Emergency Maintenance Guide
Emergency call
y
Send one person to report the
traffic accident to police, and, call
If
the
breathing
y
the ambulance at the same time.
Care for the injured
y
y
y
y
Do not move any serious injured
y
Remove
injured
stop
and blow softly.
the
artificial
teeth,
attitude that the injured is dead.
Continue
the injured.
mouth-to-mouth
Lift up the jaw of the injured and
until the ambulance arrives.
tilt his/her head backwards to
make breath smoothly.
If the injured cannot breaths yet,
firstly. And if the injured can talk
hold his nose and implement the
or breathe, we may treat them
mouth-to-mouth
latter.
with the normal breath frequency.
Ask the quantity of passengers in
Blow abundant air to swell the
the automobile.
chest of the injured and then
unconscious
or
difficult
chest down. Repeat this action
to
y
y
For children and infants, let your
implement
the
resuscitation
Press the wound. For example,
press the wound with your thumb
to stop the serious bleeding. Do
not waste time to dress the wound,
which can be done later.
DO NOT move the injured
y
Do not move the injured unless it
is absolutely necessary. Otherwise,
until the injured starts to breathe.
breathe.
to
Bleeding
resuscitation
move away your mouth to let the
Confirm the injured who are
Do not give up. Never hold the
may disturb the breathing from
the automobile catches fire).
y
y
chewing gum and anything that
unless they are in dangerous (e.g.
Treat the unconscious injured
lip around their nose and mouth
you may make the wound worse.
y
If it is necessary to move the
213
Emergency Maintenance Guide
unconscious injured, you must
make the neck of the injured get
live until the rescue comes if you
obey these instruction
enough support.
y
Use any covering available, such
as jacket and etc, to cover the
injured to keep the temperature of
their body. DO NOT give them
food or beverage.
y
If you have to move the injured
for the sake of their safety, place
them with the prone posture.
Otherwise, keep their original
posture.
y
Talk with the injured in the
assuasive
tone
to
make
the
hysterical injured calm down.
Remember
·
The injured may die within 3
minutes, but you may keep them
214
Emergency Maintenance Guide
tand
The Chery Automobile Co., Ltd. reserves the rights to modify the Chery Automobile
Instruction Manual, and the items to be modified are subject to change without notice. Thank you
for your unders
.
Chery Automobile Co., Ltd.
No 8,Changchun Rd, Wuhu Economic and Tenological
Development Zone, Wuhu, Anhui, China
E-mail: cheryservice@mychery.co
215
Emergency Maintenance Guide
216