How to Convert a Computer ATX Power Supply to a Lab Power

How to Convert a Computer ATX Power Supply to a Lab Power Supply - wikiHow
Get our free iPhone App
Sign Up or Log In or Log In via
My Profile
the how to manual that you can edit
Home » Categories » Computers and Electronics » Hardware » Internal Components
Write An Article
How to Convert a Computer ATX Power
Supply to a Lab Power Supply
Follow wikiHow on facebook
Edited by Abizarl and 34 others
Random Article
1,321,150 people like this.
Related Articles
Computer power supplies cost
around US$30,but lab power
supplies can run you $100 or
more! By converting the cheap
(free) ATX power supplies that
can be found in any discarded
computer, you can get a
phenomenal lab power supply
with huge current outputs,
short circuit protection, and
reasonably tight voltage
regulation on the 5V line.
Build a Powerful Quiet Computer
Buy a Power Supply
Make Your Own Lineman's Telephone
Build a Shed
On most PSUs, the other lines
are unregulated.
Related Videos
Look online or at your local computer store for an ATX computer power supply. Or,
dismantle an old computer and remove the power supply from the case.
Unplug the power cable from the power supply and turn off the switch on the back
(if there is one). Also, be sure you are grounded so that you don't introduce any static
electricity and fry everything.
Upgrade your power
supply on a PC
Open a power supply
without destroying a
Install the Voltz
battery-powered pedal
Convert a high power
supply with an adapter
Remove the screws that attach the power supply to the computer case and remove
the power supply.
Cut off the connectors (leave a few inches of wire on the connectors so that you can
use them later on for other projects).
Discharge the power supply by letting it sit unconnected for a few days. Some
people suggest attaching a 10 ohm resistor between a black and red wire (from the power
cables on the output side), however this is only guaranteed to drain the low voltage
capacitors on the output - which aren't dangerous to begin with! It could leave the highvoltage capacitors charged, resulting in a potentially dangerous - or even lethal - situation.
6[8/30/2011 3:35:46 AM]
Featured Articles
Fold Bath Towels for Quick Hanging at
Manage Facebook Privacy Options
Find New Uses for Old Tennis Balls
Pack for a Festival
Recent Changes
An Anonymous visitor made an edit to
Enjoy a Private Weekend
An Anonymous visitor posted a comment on
the discussion page for Be a Hipster
22 seconds ago
How to Convert a Computer ATX Power Supply to a Lab Power Supply - wikiHow
Want to join in?
Meet a Community Member
Meet Wdt3223, a school
teacher in training who's
been with us for a year and
a half. He has made more
than 3,500 contributions,
patrolled over 16,000
changes and written 19
Gather the parts you need: binding posts (terminals), a LED with a current-limiting
resistor, a switch (optional), a power resistor (10 ohm, 10W or greater wattage, see Tips),
and heat shrink tubing.
Join The Community
Follow Us On...
Open up the power supply unit by removing the screws connecting the top and the
bottom of the PSU case.
Bundle wires of the same colors together. If you have wires not listed here (brown, etc),
see the Tips.
The color code for the wires is: Red = +5V, Black = Ground (0V), White = -5V, Yellow =
+12V, Blue = -12V, Orange = +3.3V, Purple = +5V Standby (not used), Gray = power is on
(output), and Green = Turn DC on (input).
9[8/30/2011 3:35:46 AM]
How to Convert a Computer ATX Power Supply to a Lab Power Supply - wikiHow
Drill holes in a free area of the power supply case by marking the center of the holes
with a nail and a tap from the hammer. Use a Dremel to drill the starting holes followed
by a hand reamer to enlarge the holes until they are the right size by test fitting the binding
posts. Also, drill holes for the power ON LED and a Power switch (optional).
Screw the binding posts into their corresponding holes and attach the nut on the
Connect all the pieces together.
Connect one of the red wires to the power resistor, all the remaining red wires to the
red binding posts;
Connect one of the black wires to the other end of the power resistor, one black wire
to a resistor (330 ohm) attached to the cathode (shorter lead) of the LED, one black
wire to the DC-On switch, all the remaining black wires to the black binding post;
Connect the white to the -5V binding post, yellow to the +12V binding post, the blue
to the -12V binding post, the gray to the anode (longer lead) of the LED;[8/30/2011 3:35:46 AM]
How to Convert a Computer ATX Power Supply to a Lab Power Supply - wikiHow
Note that some power supplies may have either a gray or brown wire to represent
"power good"/"power ok". (Most pSU's have a smaller orange wire that is used for
sensing-- 3.3V- and this wire is usually paired at the connector to another orange
wire. Make sure this wire is connected to the other orange wires, otherwise your lab
power supply won't stay on.) This wire should be connected to either an orange wire
(+3.3V) or a red wire (+5V) for the power supply to function. When in doubt, try the
lower voltage first (+3.3V). If a power supply is non ATX or AT compliant, it may have
its own color scheme. If yours looks different that the pictures shown here, make sure
you reference the position of the wires attached to the AT/ATX connector rather than
the colors.
Connect the green wire to the other terminal on the switch.
Make sure that the soldered ends are insulated in heatshrink tubing.
Organize the wires with a electrical tape or zip-ties.
12[8/30/2011 3:35:46 AM]
How to Convert a Computer ATX Power Supply to a Lab Power Supply - wikiHow
Check for loose connections by gently tugging on them. Inspect for bare wire, and
cover it to prevent a short circuit. Put a drop of super-glue to stick the LED to its hole. Put
the cover back on.
Plug the power cable into the back of the power supply and into an AC socket. Flip
the main cutoff switch on the PSU if there is one. Check to see if the LED light comes on.
If it has not, then power up by flipping the switch you placed on the front. Plug in a 12V
bulb into the different sockets to see if the PSU works, also check with a digital voltmeter. It
should look good and work like a charm!
Options: You don't need an additional switch, just connect the green and a black wire together.
The PSU will be controlled by the rear switch, if there is one. You also don't need an LED, just
ignore the gray wire. Cut it short and insulate it from the rest.
Some newer power supplies will have "voltage sense" wires that need to be connected to the
actual voltage wires for proper operation. In the main power bundle (the one with 20 wires),
you should have four red wires and three orange wires. If you only have two orange wires, you
should also have a brown wire which must be connected with the orange. If you only have
three red wires, another wire (sometimes pink) must be connected to them.
Also some power supplies need the grey and green to be connected together in order to run.[8/30/2011 3:35:46 AM]
How to Convert a Computer ATX Power Supply to a Lab Power Supply - wikiHow
If the power supply does not work, that is, no LED light, check to see if the fan has come on. If
the fan in the power supply is on, then the LED may have been wired wrong (the positive and
negative leads of the LED may have been switched). Open the power supply case and flip the
purple or gray wires on the LED around (make sure that you do not bypass the LED resistor).
If you are not sure of the power supply, test it in the computer before you harvest. Does the
computer power on? Does the PSU fan come on? You can place your voltmeter leads into an
extra plug (for disk drives). It should read close to 5V (between red and black wires). A supply
that you have pulled may look dead because it does not have a load on its outputs and the
enable output may not be grounded (green wire).
ATX power supplies are switched-mode power supplies (info at ); they must always have some
load to operate properly. The power resistor is there to "waste" energy, which will give off heat;
therefore it should be mounted on the metal wall for proper cooling (you can also pick up a
heatsink to mount on your resistor, just make sure the heatsink doesn't short circuit anything).
If you will always have something connected to the supply when it is on, you may leave out
the power resistor. You can also consider using a lighted 12v switch, which will act as the load
necessary to turn on the power supply.
Feel free to add some pizazz to the dull grey box.
You can also convert this to a variable voltage power supply - but that is another article (hint:
Uses a 317 IC with power transistor).
The voltages that can be output by this unit are 24v (+12, -12), 17v (+5, -12), 12v (+12, GND),
10v (+5, -5), 7v (+12, +5), 5v (+5, GND) which should be sufficient for most electrical testing.
Many ATX power supplies with a 24-pin connector for motherboards will not supply the -5V
lead. Look for ATX power supplies with a 20-pin connector, a 20+4-pin connector, or an AT
power supply if you need -5V.
If you DO have a sense wire for the 3.3v. , connecting the the 3.3 v. part of the supply, using
the 3.3v. voltage as a buck voltage against, say the 12v. to get 8.7v. will not work. You will
see 8.7 v. with a volt meter but when you load that 8.7v. circuit the power supply may go into
protective mode and shut the whole supply down.
You can add a 3.3 volt output (such as to power 3V battery-powered devices) to the supply by
hooking the orange wires to a post (making sure the brown wire remains connected to an
orange wire) but beware that they share the same power output as the 5 volt, and thus you
must not exceed the total power output of these two outputs.
To get more room you can mount the fan on the outside of the PSU case
If you don't feel like soldering nine wires together to a binding post (as is the case with the
ground wires) you can snip them at the PCB. 1-3 wires should be fine. This includes cutting
any wires that you don't ever plan on using.
The +5VSB line is +5V standby (so the motherboard's power buttons, Wake on LAN, etc.
work). This typically provides 500-1000 mA of current, even when the main DC outputs are
"off". It might be useful to drive an LED from this as an indication that the mains are on.
The -5v rail was removed from the ATX specification and does not exist on all ATX power
The fan on a PS can be quite loud, its designed to cool a relatively heavily loaded PS as well
as the computer. There is the possibility of just clipping the fan but is not a good idea. A work
around is to cut the red wire going to the fan (12V) and connect it to a red wire going out of
the PS (5V). Your fan will now be spinning significantly slower and thus quieter, but still
provide some cooling. If you plan to draw a lot of current from the PS this might be a bad idea,
be your own judge and see how hot the thing gets. You can also remove the stock fan and
replace it with a quieter model (there will be soldering to do though.)
Some power supplies will have both a sense+ and sense- (on the circuit board S+ and S-) In
this case the S+ must be connected to 3.3V and the S- must be connected to ground. While
some power supplies may differ, I found S+ was orange (connect to orange 3.3V) and S- was
brown (connect to black ground)
Line voltage can kill (anything above 30 milliamps/volts can kill you in a matter of time if it
somehow penetrates your skin), and at the very least give you a painful shock. Make sure that
you have removed the power cord before doing the conversion and have discharged the
capacitors as described in the steps above. If in doubt, use a multimeter.[8/30/2011 3:35:46 AM]
How to Convert a Computer ATX Power Supply to a Lab Power Supply - wikiHow
If you suspect the power supply is damaged, do not use it! If it is damaged, the protection
circuitry may not work. Normally, a protection circuit will slowly discharge the high voltage
capacitors - but if the supply was connected to 240V while set at 120V (for example), the
protection circuits have probably been destroyed. If so, the power supply might not shut down
when it is overloaded or when it begins to fail.
Do not touch any lines leading to capacitors. Capacitors are cylinders, wrapped in a thin plastic
sheath, with exposed metal at the top with a + or K usually. Solid-state capacitors are shorter,
a little wider in diameter, and do not have a plastic sheath. They retain a charge much like
batteries do, but unlike batteries, they can discharge extremely fast. Even if you have
discharged the unit, you should avoid touching any points on the board except where
necessary. Use a probe to connect anything you might touch to ground before beginning any
Do not remove the circuit board unless you must. The traces and solder on the underside
could still have high voltage on them if you didn't let the PSU sit long enough. If you must
remove it, use a meter to check for voltage on the pins of the largest capacitors. When you
replace the board, make sure that the plastic sheet goes back under the board.
When drilling the metal case, make sure no metal filings get inside the PSU. These could
cause shorts, which in turn could cause a fire, extreme heat or dangerous electrical spikes on
one of your outputs which will break your new lab power supply which you worked so hard on.
A computer power supply is fine for testing purposes, or for running simple electronics (eg
battery chargers, soldering irons) but will never produce power like a good lab power supply,
so if you intend on using your power supply for more than just testing, buy yourself a good lab
supply. There is a reason they cost so much.
It is strongly recommended that you discharge the capacitors. Plug in the power supply, turn
on the power (short the Power (green) wire to ground, then unplug the power supply until the
fan stops spinning.
This will almost certainly void any warranty.
The resulting power supply will provide high output power. It might happen you create an
electric arc at the low voltage outputs or fry the circuit you are working on, if you make any
mistake. Lab PSUs have adjustable current limitation for a reason.
Things You'll Need
An ATX power supply of any rating above 150 Watt (can be found from an obsolete computer,
online, or at your local computer store)
Wire cutters
Needle nose pliers
Soldering Iron & Solder
Electrical Tape
Heat Shrink Tubing & Heat Gun
Binding posts
Current limiting resistor for the LED (330 ohms)
Power resistor to load the power supply
Low Wattage Switch
Computer Power Cable
Related wikiHows
Build a Powerful Quiet Computer
Buy a Power Supply
Make Your Own Lineman's Telephone
Build a Shed
Make a Simple and Effective Garage Workbench
Add Variable Voltage to Your ATX Based Bench Power Supply
Use an Old ATX Power Supply As a Lab Power Supply Without Modification[8/30/2011 3:35:46 AM]
How to Convert a Computer ATX Power Supply to a Lab Power Supply - wikiHow
How to Create a 12 Volt DC Test Bench for Bullet Cameras Using an Old ATX Computer
Power Supply
Sources and Citations
Articles for You to Write
Here is a list of suggested articles that have not yet been written. You can help by researching and writing
one of these articles. To get started writing one of these articles, click on the red link of a title below.
Gather Supplies for Making Tie dye T shirts
Build a Lighted Sign
Make Solder Look Old
Build Your Own Work Table
Make a Charger Box
Article Info
Last edited:
July 10, 2011 by Maniac
Featured Article
Featured Articles | Internal Components
Recent edits by: Victoria Ann, Harri, Noscco427 (see all)
Article Tools
Share this Article:
Send fan mail to authors
+ Embed this: Republish this entire article on your blog or website.
Thanks to all authors for creating a page that has been read 1,227,091 times.
Was this article accurate?
the how to manual that you can edit
Explore Categories
About wikiHow
Terms of Use
Arts and Entertainment
Cars and Other Vehicles
Computers and Electronics
Education and Communications
Family Life
Finance and Business
Food and Entertaining
Hobbies and Crafts
Holidays and Traditions
Home and Garden
Personal Care and Style
Pets and Animals
Philosophy and Religion
Relationships[8/30/2011 3:35:46 AM]
How to Convert a Computer ATX Power Supply to a Lab Power Supply - wikiHow
Site map
Sports and Fitness
All text shared under a
Creative Commons License .[8/30/2011 3:35:46 AM]
Powered by Mediawiki.
Work World