C53_pg_202-203
8/13/08
10:15 AM
Page 203
SATV/CATV
section
13
SATV/CATV
H21 High Definition Receiver
With the DIRECTV® H21 receiver,
you can access over 265 digital-quality
audio and video channels from
DIRECTV® in both high definition and standard
definition Features: •Versatile HDTV connection
options include HDMI digital audio/video and
component video, as well as standard composite
video and RCA audio •1080i picture output resolution
formats •Dolby Digital 5.1 surround sound capable
•MPEG-4 AVC capable Includes: •Access card
•B-band convertor •Remote control and batteries
•Component, S-video, and standard A/V cables
•Phone and power cords •User guide (DIRECTV®
service and installation not included) •Mfr. #H21
Order #
33-7703
(ea.)
$135.00
DIRECTV® Standard Receiver
With the DIRECTV® D12 receiver,
you can access over 250 digital-quality
channels, plus access interactive
capabilities and a customizable on-screen program
guide. Explore and personalize all your viewing
options quickly and easily with the included remote
control. Features: •Interactive features include
Mix Channels, DIRECTV® Active, and MiniGuide
•Parental controls to set rating restrictions and
spending limits •Programming options like CHOICE,
DIRECTV® Spanish, XM satellite radio and pay per
view movie and event channels Includes: •Access
card •Remote controls and batteries •A/V and
S-video cables •Phone and power cords •User
guide (DIRECTV® service and installation not
included) •Mfr. #D12-300
Order #
33-7701
Antennas . . . . . .209, 211
Antenna Rotors . . . . .212
Attenuators . . . . . . . .207
A/V Distribution . .217~218,
222~225
A/V Switches . . . .214~216
Baluns . . . . . . . .222~225
Diplexers . . . . . . . . . .205
Convertors . . . . .214, 218
Ground Loop Isolators 218
Filters . . . . . . . . . . . .208
Multi-Switches . . . . . .205
RF Amplifiers . . .205, 208,
220~221
RF Modulators . . . . . .219
RF Splitters . . . .206~207
Satellite Products 203~205
(ea.)
$94.95
DIRECTV® R16 Receiver Plus DVR
Order #
33-7702
(ea.)
$139.00
The Terk TRK-S26 is a
DIRECTV Multi-Satellite
Dish Antenna that provides
three integrated LNBs so
you can receive all available
DIRECTV® programs, including
HDTV and DIRECTV PARA
TODOST M programming. In
addition, it saves you money by
eliminating additional hardware
installation that you would need to
receive these services. The TRK-S26
features four identical outputs letting you connect
up to four receivers for a household system, and its
compact size makes it an ideal choice to use with RVs
and motor homes. A DIRECTV approved antenna is
a necessity if you are looking to receive the best from
DIRECTV® service. The TRK-S26 can also be installed
faster with its refined and improved mounting system
and its three-way tilt, for easier rotation.
Mfr. #
TRK-S26
High Definition HR21 Receiver
Add DIRECTV® and DVR Service
and you get the best choice and
widest selection of high definition
programming. Features: •Standard-definition (SD)
and high definition (HD) enabled •Simultaneous SD
and HD output •Record up to 200 hours of SD, or up
to 50 hours of HD programming •Two satellite tuners
for access to SD and HD DIRECTV programming
•14-day Advanced Program Guide® •Pause and
rewind live TV for up to 90 minutes •Series Link®
feature •One touch record, auto record, manual
record, and bookmarks •Search and record
•Interactive TV enabled. •Mfr. #HR21 Note:
(DIRECTV® service and installation not included).
Order #
33-7704
18" x 20"
DIRECTV Multi-Satellite
Dish Antenna
®
Order #
33-9670
Ka/Ku Dish for HD Programming
(1-5)
$101.00
(ea.)
$339.00
The latest in satellite dish antennas, this dish is
specifically designed for use with DIRECTV® HR20
and H20 high definition receivers. Capable of MPEG-4
compression, the dish has three LNBs to receive 101°,
110°, and 119° satellites, plus one to receive the new
KA satellite (99° and 103°) for local HD programming
(where available). Features: •Four outputs carry
satellite signal from all five satellites •Heavy-duty
J-mount with 2" outer diameter mast opening •LNB
arm with LNBS attached extends 23.5" from dish
surface area. Includes dish, J-mount mast, LNBs,
arm and pole attachment. Dish surface dimensions:
25.5" (H) x 29.5" (W).
Order #
33-10410
33-10411
33-10412
Description
Ka/Ku Dish
Short wall mount brace
Long wall mount brace
(ea.)
$146.00
14.95
14.95
DIRECTV® International Dish
With special LNBFs designed
specifically for DIRECTV®
worldDIRECT programming, this
dish is equipped with linear and dual LNBFs for
simultaneous reception of the 95° west and 101°
west international programming satellites. An
optional multi-switch is required to bring in both
satellites. Features: •Two outputs on the 95° and
two on the 101° •Includes dish, LNBs, arm, and
mount. Dish surface dimensions: 24" (H) x 36" (W).
Order #
33-10415
(ea.)
$99.00
www.mcmelectronics.com
Portable/Remote
Digital Satellite System
•Lightweight, easy to set up and ready to go •Bases
are completely and permanently assembled •Base has
built in level and compass •Convenient handle for
carrying and 25' of cable permanently stored in the
bottom of the base •Perfect for camping, fishing trips,
tailgating and picnics
Order #
RD-9046
NET 30
Terms
(ea.)
$171.69
203
13
The DIRECTV Plus™ DVR receiver
lets you record up to 100 hours of
programs, and pause or control live
TV. With the R16 receiver you can automatically
record an entire season of your favorite shows, find
and record programs by title, actor, or director, listen
to theater-quality Dolby Digital sound, and schedule
recording up to 14 days in advance. Includes:
•Access card •Remote controls and batteries
•A/V and S-video cables •Phone and power cords
•User guide (DIRECTV® service and installation
not included) •Mfr. #R16
C53_pg_204-205
section
13
8/13/08
10:18 AM
Page 204
SATV/CATV
High Performance Dual LNB
DBS LNB for use with digital
satellite system dishes with
rectangular shaped tubes.
Designed to work with “D” shaped
tubes as well. Perfect low cost
replacement for damaged LNBs.
#33-7391
Acutrac®22 Digital Satellite Signal Level Meters
The Acutrac®22 allows an installer to easily
align a multi–feed system by displaying LNB A
and LNB B signal strength measurement levels
simultaneously. The Acutrac®22 features include:
LCD display, selectable audio on-off tone, receiver
voltage output, individual LNB current consumption,
22KHz tone and coax cable test. Acutrac®22 Pro
also includes: Rechargable battery pack, leather
case and AC/DC chargers.
Order #
33-7391
33-7395
Mfr. #
Acutrac22
AcutracPro
13
Satellite Signal Level Meters
The 1004IFD and 1007IFD are intended to aid in
the alignment of a satellite dish. They include satellite
IF (950~2150MHz) amplification and a broadband
detector. The detector drives a meter and a variable
frequency audio tone. The dish is then aligned for
maximum meter deflection or highest pitch tone.
A gain control allows a wide range of input signal
levels. The units are connected to the LNB via a
short coaxial cable. The 1004IFD output must be
connected to the satellite receiver in order to supply
power. The units operate from 11~24VDC on the
coaxial cable. Connection to the receiver is optional
with the 1007IFD, but extends battery life between
charges. All models allow measurement of voltage
on the coaxial cable. The 1007IFD will also measure
LNB current. The 1007IFD includes an internal
rechargeable battery pack, carrying strap and a
wall plug recharging unit. The internal battery pack
allows a dish to be aligned before it is connected to
the satellite receiver. The battery pack is switchable
between 13 and 18V output, allowing either
polarization to be selected when used with a voltage
switched LNB. In US DBS applications, LHCP is
selected when the LNB voltage is nominally 17V.
Order #
33-9295
33-9300
Mfr. #
1004IFD
1007IFD
(ea.)
$109.00
198.00
Sat-Finder
Satellite Meter
The Sat-Finder makes
it easy to find maximum
satellite signal. Simply
connect between the satellite
receiver and the LNB to precisely align the dish in
seconds. The Sat-Finder has a faster response time
than the receiver’s signal strength meter for more
precise adjustments.
Order #
33-7725
(1-9)
$26.95
(10-49)
$26.95
Order #
33-10405
The satellite finder kit makes aligning a dish simple
and easy. The satellite finder attaches to the output
of the LNB or LNA and supplies power to the
LNB/LNA via the battery holder, or hook the finder
in-line with the receiver. Works with C or K band
satellites and DSS/DBS. Specifications: Frequency
range: 950~1550MHz, power supply: 12~18VDC,
60mA, input sensitivity: 62~80dB, impedance: 75ohm.
Kit includes: •Satellite finder, compass, RF jumper
cable and battery holder all in a vinyl carry case
•Use #27-1335 battery pack for DSS applications
Order #
33-1975
Use with next generation DBS dishes
for DISHNetwork and DIRECTV® to
switch between programming on two
LNBs. Controlled by the
DISHNetwork receiver.
204
Precision C and Ku Band LNBs
“C” and “Ku” band LNBs for use with “C” band
antennas. Professional feedhorns and commercial
grade LNBs assure high performance with low
noise. Input and output frequencies are in GHz.
Fig. Order #
A 33-4695
B 33-4700
C 33-4705
D 33-4710
Noise
Band
C
C
Ku
Ku
Input
Figure
17K
15K
0.6
0.5
Output
Freq.
3.7~4.2
3.4~4.2
11.7~12.2
11.7~12.2
Freq.
(ea.)
.950~1.45 $24.95
.950~1.45 34.95
.950~2000 32.27
.950~2000 38.95
4DTV compatible C/Ku feedhorn with digital “C”
band and “Ku” band LNBs. This feedhorn allows
for digital satellite viewing of both formats from
one “C” band satellite dish. Specifications:
(C-Band) Input frequency: 3.7~4.2GHz.
Polarization: Linear, 3 wire servo type. Output
frequency: .950~1450GHz. Noise figure: 20°K.
(Ku Band) Input frequency: 10.95~12.5GHz.
Polorization: Linear, three wire servo type. Output
frequency: .950~1450GHz. Noise figure: .6dB max.
Order #
33-4720
(ea.)
$194.00
Compass
Economical compass for easily
identifying satellite positions.
Small size fits in the palm
of your hand. Top closes to
protect surface from scratches.
Specifications: •Directional
accuracy: ±5° •Direction
indication: 2°/scale •Dimensions:
72mm x 55mm x 30mm
(kit)
$52.95
This hand held CATV/satellite
meter has been designed for
the technician to make quick
and accurate signal strength
measurements for both CATV
and satellite. This powerful,
simple to use tool measures
frequencies from 25MHz~1550MHz.
•Measures satellite from DIRECTV®,
Dish-Network, CATV and broadcast
signal strength •Two rows of ten
easy-to-read indicator lights •Hand
held design, great for use with HDTV
•Includes 22KHz tone generator
for use with dual satellite systems
•Requires 9V battery (included)
DISHNetwork
Block Switch
(1-4)
$30.29
D
B
RF/Satellite
Meter
(ea.)
$60.77
Order #
33-6915
C
A
4DTV Compatible C/Ku Feedhorn with LNB
Satellite Finder Kit
Use for fast and accurate
satellite dish alignment. This
lightweight, easy to use meter
is compatible with Dish Network®
and DIRECTV® systems, and
can be powered by the internal,
rechargeable NiMH battery, or by
the satellite receiver. Read signal
strength on the digital LCD display,
or use the variable audible tone
function for hands-free operation.
Functions include signal strength,
current consumption and receiver output voltage.
Also includes a DiSEqC multi-switch channel display
mode. Includes 18VDC power adaptor.
(ea.)
$37.95
(50-up)
$25.95
(ea.)
$59.95
129.00
Single LNB Digital
Satellite Meter
Order #
33-7435
Order #
33-9695
Mfr. #
M200
(1-9)
$462.00
1-800-543-4330
Fax 1-800-765-6960
(10-up)
$423.00
Order #
33-2050
(ea.)
$5.34
(2-10)
$4.87
(11-up)
$3.81
Suunto Tandem
Inclinometer/Compass
The Suunto Tandem is two precision
satellite tools in one. Slope/height
(inclinometer) measurements are easily
done through the sight to alert you to
possible obstructions. Accurate satellite
bearings can be found with the liquid
filled precision compass. Mfr. #PVCOMAF.
Order #
33-7420
(ea.)
$209.00
C53_pg_204-205
8/13/08
10:19 AM
Page 205
SATV/CATV
Multi-Switches
Features: •Six satellite inputs;
four inputs for the traditional
101°/110°/119°W LNBs, and for the two additional
Ka LNBs for 99°W and 103°W. •Two additional
FlexPort inputs commonly used to interface additional
DIRECTV® satellites at locations such as 72.5°W and
95°W. Specifications: •Input frequency range:
250~2150MHz •Output frequency range:
250~2150MHz (each output) •Insertion loss: -7dB
(min.) •Cross polar isolation: 30dB min. •Current
consumption: 250mA (typical) 300mA (max.) •Power
adaptor: 100~240VAC 50~60Hz input; 21VDC, 1.5A
output •22KHz tone output: 22 ± 4 KHz continuous,
650 ±300mV p-p (power adaptor included).
Order #
33-10300
5 x 12 Multi-Satellite Multi-Switch
Four satellite IF and one terrestrial TV input to 12
outputs to satellite receivers. Built–in satellite IF
amplifier compensates for splitter loss. LNB selection
by 14/18VDC and 22KHz tone provided by equipped
receivers. Built–in power supply provides power for
operation, amplification and operation of the LNBs.
Order #
33-8690
(1-9)
$84.95
(10-up)
$82.95
(ea.)
$198.00
In-Line Amplifiers
In-Line
950~2150MHz Amplifier
(1-9)
$13.64
(10-up)
$10.66
Indoor/Outdoor
In–Line Amplifier
Order #
33-9665
Amplifies satellite and
terrestrial signals to compensate for splitters and
long cable runs. TERK amplifiers are designed for
optimum performance in TV and satellite. Lesser
quality amplifiers do not offer extended bandwidth
and gain flatness resulting in poor picture quality.
High-quality die–cast aluminum housing.
Specifications: Frequency range: 54~2150MHz.
Slope compensation gain: 11dB @ 54MHz, 20dB
@ 2150MHz. Noise figure: <5dB. Input/output
impedance: 75ohm.
Mfr. #
BIA-20BP
(ea.)
$26.95
Satellite Line Amplifiers
The 5113IFD is a general purpose, low cost satellite
IF (950~2050MHz) line amplifier with 14dB gain
at 1450MHz and appropriate gain between 950 and
2050MHz to give cable slope compensation. Typical
applications include: Long runs of coaxial cable
(greater than 100') from satellite receiver to LNB,
satellite IF distribution system where signal levels
may have become marginal towards the end of the
system, splitting a signal many ways which might
cause excessive splitting loss. Includes two amplifiers
in one housing. This is for dual cable, dual
polarization systems.
Order #
33-9440
5 x 8 Integrated Multi–Switch
The BMS-58 allows up to eight satellite television
receiver connections to a single multi–satellite dish
and provides an additional off air antenna/cable
input to integrate all television options. With the
Terk BMS-58 multi–switch you can install a home
theater multiplex in no time by connecting up to
eight receivers with ease. There is no need to remove
integrated multi–switches already embedded in the
satellite dish. Simply connect the two SatA and SatB
cables to the BMS-58 and run to the receivers. The
BMS-58 has an ultra–low noise built–in amplifier
to eliminate signal loss and deliver the best possible
reception to every TV. The TERK BMS-58 is designed
to be waterproof making it rugged, durable and easy
to install. Mfr. #BMS-58.
Mfr. #
5113IFD
(ea.)
$7.99
(ea.)
$79.95
Satellite Diplexers
The 4001IFD and 4002IFD
diplexers are used for separating
or combining satellite signals at
950~2150MHz with VHF/UHF signals
at 54~806MHz. In addition, a DC
power pass is provided from the satellite port to
the common in order to pass satellite receiver LNB
voltage. The 4001IFD is Channel Master’s standard
performance diplexer. The 4002IFD offers higher
performance (much greater stopband rejection)
necessary when combining satellite and VHF/UHF
signals on to one cable because LNB noise extends
down into the UHF spectrum and can degrade UHF
TV reception if not adequately filtered out before
connection to the distribution cable. Model 4022IFD
contains two 4002IFD diplexers and a VHF/UHF
signal splitter. When used with a twin LNB, diplexed
satellite and VHF/UHF signals are provided to two
locations within a building. Model 4032IFD is
identical except DC is passed from one output
to the VHF/UHF input for preamplifier power.
Order #
33-9415
33-9420
Mfr. #
4001IFD
4002IFD
(ea.)
$4.49
10.95
VHF/UHF/Satellite
Diplexer-Mixer
The TSDM-2150 is a compact
television antenna satellite
diplexer/combiner used in
applications that require satellite I.F. distribution
from 950~2150MHz. The TSDM-2150 uses a rugged
case that allows for outdoor use. Specifications:
•Frequency range: Satellite: 950~2150MHz,
television antenna: 40~860MHz •Connectors:
“F” type •EMI performance: >80dB
Order #
33-2710
(1-9)
$4.99
(10-49)
$4.79
(50-up)
$4.49
Budget Diplexer
Satellite Distribution
Multi-Switches
Channel Master® Multi-switches are used to provide
satellite signals of either RHCP or LHCP polarization
from one dish at four or eight locations. In addition,
when required, they provide terrestrial VHF/UHF
signals diplexed on the same coaxial cable. At the
customer outlet, the satellite signals are separated
from the VHF/UHF signals with a diplexer such as
model 4001IFD. Model 6214IFD and Model 6228IFD
combine VHF/UHF (54~806MHz) signals with
satellite IF signals on one cable to provide up to eight
independently switchable wideband outputs. Passive
VHF/UHF processing allows complete flexibility for
VHF/UHF amplification. Models 6314IFD and
6328IFD amplify VHF/UHF (54~806MHz) signals
and combine them with satellite IF signals on one
cable to provide up to eight independently switchable
wideband outputs. They should be used when all
desired VHF/UHF terrestrial TV signals can be
received at comparable levels from a stationary
antenna or antenna system.
Order #
33-9490
33-9495
33-9500
33-9505
Mfr. # Description
6214IFD
3x4
6314IFD
3x4
6228IFD
3x8
6328IFD
3x8
Amplified Terr. (ea.)
No
$89.95
Yes
84.95
No
109.00
Yes
139.00
www.mcmelectronics.com
Zinc plated die cast diplexer to
combine off air television signals
with satellite for ease of system
installation. Power passive one
port. Bandwidth: 40~2150MHz.
Order #
33-4810
(1-9)
$2.99
(10-up)
$2.56
Diplexer
Combines and
separates your DBS satellite and
off–air signals. TERK diplexers
deliver sharper cut–off frequencies,
lower signal loss and better impedance
matching. Low quality diplexers can
cause signal loss and poor picture quality. High
quality die–cast aluminum housing. Specifications:
Frequency response: 54~2150MHz. Impedance:
75ohm. Insertion loss: Antenna, 1dB, Satellite, 2dB.
Return loss: 10dB. Isolation: Antenna, 40dB, Satellite,
40dB. Mfr. #BDS-21BP.
Order #
33-7235
NET 30
Terms
(ea.)
$14.95
205
13
Features: Die-cast housing, low noise: 4dB, high
gain: 20dB, passes DC through for powering LNBs,
sloped gain for long cable runs, voltage supplied
by the satellite receiver Specifications: •Noise
figure: 4dB •Gain: 950MHz: 15dB, 1450MHz: 18dB,
1750MHz: 20dB, 2150MHz: 21dB •Maximum output:
30dBmV (12 channels) •DC voltage: 15~18VDC
(negative ground) •Connectors: “F” type
Order #
33-7220
13
Diplexers
Wide Band
6 x 16
Multi-Switch
Order #
33-2720
section
C53_pg_206-207
section
13
8/13/08
10:19 AM
Page 206
SATV/CATV
Hi-Frequency RF Splitters
D
E
C
B
A
Vertical
Splitters
High Frequency
RFI Splitters
DIRECTV®
compatible high
C
frequency performance
to 3GHz. •Tin-plated zinc
die-cast housing with soldered back to achieve RFI
-130dB •Waterproof and airtight up to 30 P.S.I. with
4.55mm grounding hole and stainless steel screws
•Low thru loss and high isolation with patent
pending 360° insert pin. Bandwidth: 5MHz~3000MHz.
Fig.
A
B
C
Order #
33-10245
33-10246
33-10247
Description
2-way
3-way
4-way
(ea.)
$2.79
3.19
3.79
(2-up)
$2.29
2.79
3.19
Order #
5~1000MHz
33-4880
33-4885
33-4890
33-4895
33-4900
5~2150MHz
33-7140
33-7150
33-7155
33-7160
High Frequency Horizontal Satellite Splitters
Description
(1-9)
(10-up)
2-way
3-way
4-way
6-way
8-way
$3.02
4.03
5.04
6.05
7.06
$2.59
3.63
4.15
5.19
6.23
2–way
4–way
6–way
8–way
5.99
9.99
15.95
17.95
5.65
8.99
13.34
15.40
Mini Hi-Frequency Splitter
13
Mini hi-frequency splitter saves
space in confined areas.
DC passive one port.
Attached plastic cable
channel provides neat installations.
Bandwidth: 5~2250MHz. Measures:
2" x 2" x 1" (port to port).
Order #
33-4860
(1-9)
$5.04
A
(10-up)
$4.67
B
•High-grade circuitry
allows the connection
of components with
minimal signal loss
•Maximum transfer of all your RF signals including
higher digital frequencies means quality reception and
excellent picture output •Splits a 75Ω coaxial signal
from cable TV, an antenna or a VCR for connection
to two TVs/VCRs •Frequency: 5MHz~2.4GHz
•Gold-plated input/outputs for reliable connectivity
•Dual-grounded connections •Precision cast body
(ea.)
$10.95
•Heavy-duty, die-cast design •Power passive •Low
thru-loss •950MHz~1750MHz •For use with satellite
systems and other high-frequency applications
Fig
A
B
Order #
33-0035
33-0040
Description
2-way
4-way
(1-9)
$8.39
13.84
Four-Way
Digital Splitter
(10-up)
$8.22
13.19
Budget High Frequency Splitter
High frequency for use in DSS and
satellite installations. One port is DC
passive. Bandwidth: 5~2400MHz.
Order #
33-8640
(1-9)
$2.07
•Gold–plated
inputs/outputs
•Dual–grounded
connections
•5MHz to 1GHz •Precision cast body
Order #
DT4SP
Description
(1-9)
(10-up)
2-Way
3-Way
4-Way
6-Way
8-Way
$6.05
8.07
8.99
16.11
17.12
$5.19
7.27
8.23
15.55
16.59
2-Way
3-Way
4-Way
6-Way
8-Way
6.49
8.07
9.21
16.35
17.12
5.49
7.27
8.44
15.78
16.59
(ea.)
6.30
B
C
D
E
A
High Frequency Vertical Satellite Splitters
High frequency vertically oriented splitters used
for satellite and DSS applications. Power passive to
operate in-line amps and multi-switches. Bandwidth:
5MHz~3000MHz.
Fig. Order #
1 Port Passive
A
33-10235
B
33-10236
C
33-10237
D
33-10238
E
33-10239
All Ports Passive
B
33-10241
C
33-10242
D
33-10243
E
33-10244
Description
(1-9)
(10-up)
2-way
3-way
4-way
6-way
8-way
$5.99
7.99
8.99
15.95
16.95
$5.69
7.59
8.54
15.15
16.10
3-way
4-way
6-way
8-way
7.99
8.99
15.95
18.95
7.59
8.54
15.15
17.95
C
Drop Enclosures
B
These drop enclosures will house and protect components from
the elements that corrode and shorten their lives. Drop boxes
produce a professional appearance for cable TV and satellite
installations. The Econo Box combines the design and features of
a drop box with an economical price. The Omni II box offers simplicity of
installation and professional appearance along with a generous interior and the ability to
seal the box for drop security. The Residential Control Box is designed to offer visual evidence of tampering
and provides for easy maintenance. All boxes are UV resistant and come in a neutral gray color.
Fig. Order # Description Dimensions (H) x (W) x (D) (ea.)
Fig. Order # Description Dimensions (H) x (W) x (D) (ea.)
A 33-6940 Econo box 7.25 x 4.75 x 1.75 (D)
$4.09
C 33-6950 Residential 8.75 x 6.25 x 2.75
$6.09
B 33-6945 Omni II box 5.75 x 5.0 x 1.25
2.89
Control box
206
Fig
Order #
1 Port Passive
A
33-4350
B
33-4355
C
33-4360
D
33-4365
E
33-4370
All Ports Passive
A
33-4375
B
33-4380
C
33-4385
D
33-4390
E
33-4395
(10-up)
$2.01
C
A
High frequency splitters used for satellite and DSS
applications. Power passive to operate in–line amps
and multi-switches. Bandwidth: 5MHz~3000MHz.
2.4GHz Four Way
Bi-Directional Splitter
Order #
DT44SP
High-Frequency
Splitters
B
A
•Nickel plated zinc die-cast
housing •RFI shielding
•2GHz splitters feature
one power passive port
marked on the splitter
1-800-543-4330
Fax 1-800-765-6960
A
Power Passive
Splitters
Power passive
splitters allow
for use of in-line
amplifiers and
B
other DC
powered devices. For applications to 1000MHz.
Fig
A
B
C
Order #
33-4400
33-4405
33-4410
Description
2-way
3-way
4-way
(1-9)
$2.69
3.29
3.79
(10-up)
$2.29
2.79
3.39
C53_pg_206-207
8/13/08
10:20 AM
Page 207
SATV/CATV
RF Taps
Solder Back Indoor/Outdoor
Directional Couplers and Taps
(1-9)
(10-up)
$2.49
2.49
2.49
2.49
2.49
2.49
2.49
2.49
2.49
$2.26
2.26
2.26
2.26
2.26
2.26
2.26
2.26
2.26
Order #
33-3000
33-3010
Value
8dB
16dB
(1-9)
$6.25
6.25
(10-up)
$5.92
5.92
CATV FM Tapoff
B
Order #
Loss (dB)
B. In-Line Style-SRT models
33-2971
4
33-2976
6
33-2981
9
33-2986
12
33-2991
16
33-2996
20
33-2997
24
33-2998
27
33-2999
30
(1-9)
(10-up)
$2.49
2.49
2.49
2.49
2.49
2.49
2.49
2.49
2.49
$2.26
2.26
2.26
2.26
2.26
2.26
2.26
2.26
2.26
C
Order #
33-350
(1-9)
$4.49
(10-99)
$4.02
(100-up)
$3.53
A
B
C
Indoor Splitters
Performance to 1000MHz. 2, 3, 4 and 8 way models.
Die-cast housing. RF shielding. Mounting tabs and
grounding blocks.
Fig
A
B
C
D
Order #
33-2900
33-2905
33-2910
33-2915
U/V Directional Taps
•Nickel plated solid brass body
•Monolithic ceramic printed
circuit board, ensuring rugged
construction •Bandwidth:
5KHz~950MHz •Not DC passive •5% accuracy
•22 gauge steel center pin •Small: 13⁄8" size •“F” type
female to male •75ohm •Three attenuators to choose
from •Sorry–no mixing of values for quantity pricing.
Order #
33-790
33-795
33-810
dB
3
6
12
(1-9)
$3.09
3.49
3.49
(10-49)
$2.68
3.29
3.19
(50-up)
$1.77
2.79
2.89
In-Line Splitters
A
Order #
Description
(1-9)
A. One Output Zinc Die-Cast
33-1175
12dB
$2.89
33-310
17dB
2.99
33-1180
23dB
3.09
B. Two Outputs
33-1185
12dB
4.29
C. Four Outputs
33-1195
12dB
5.99
33-330
17dB
5.89
33-1200
23dB
6.09
(10-49)
(50-up)
$2.61
2.70
2.74
$2.24
2.32
2.35
3.83
3.54
5.62
5.36
5.70
4.77
4.55
4.84
Order #
33-4865
33-4870
33-4875
Description
2-way
3-way
4-way
(10-up)
$2.59
3.63
4.67
(10-up)
$0.86
1.99
3.19
6.29
C
RFI Splitters
•For use in applications where additional
shielding is needed •100dB case design exceeds FCC
requirements for RF shielding •25% more zinc content
than standard splitters •Case thickness increased
by 50% to obtain very good RFI performance
•Mounting tabs with screws and grounding
block •5MHz~1000MHz frequency response
Fig.
A
B
C
Order #
33-2130
33-2135
33-2140
Type
2-way
3-way
4-way
(1-9)
$2.11
2.92
3.42
(10-up)
$1.86
2.48
3.01
C
B
Fixed Mini-Type Attenuator Pads
Features: Nickel-plated, solid brass
body, monolithic ceramic printed
circuit board, ensuring rugged construction, etched
glaze-type resistors provide ±5% accuracy and excellent
return loss, small 1.375" size, 22-gauge spring steel
center pin, female to male fitting, not DC passive.
Specifications: •Bandwidth: 100KHz~1750MHz
•Return loss: 20dB typical •Accuracy: ±5%
Order #
33-2750
33-2755
33-2760
33-2765
33-2770
33-2775
33-2780
Description
3dB
6dB
8dB
10dB
12dB
16dB
20dB
(1-9)
$1.30
1.30
1.30
1.30
1.69
1.30
1.30
(10-up)
$1.03
1.03
1.03
1.03
1.34
1.03
1.03
•For indoor and
outdoor use •RF shielding exceeds
FCC specifications •Maintains
75ohm impedance on trunk •Full
5MHz~900MHz operational range
•Use 75ohm terminator on last
trunk output (MCM #33-550)
(1-9)
$3.02
4.03
5.04
(1-9)
$0.94
2.19
3.19
6.39
B
A
Four-Way Couplers
The in-line port design
of these splitters helps to
keep cables organized and
makes them perfect for
installations in crowded
areas. Nickel plated zinc
die cast construction.
Bandwidth: 5~1000MHz.
Description
2-way
3-way
4-way
8-way
•Provides high isolation from reflected signals
•Maintains constant 75ohm impedance on trunk
line •Tap at 12, 17 and 23dB
Attenuators
Fixed Mini-Types
D
Order #
33-1425
33-1430
33-1435
Description
16dB
20dB
24dB
(1-9)
$6.25
6.25
6.25
(10-49)
$5.92
5.92
5.92
(50-up)
$5.40
5.40
5.40
www.mcmelectronics.com
Splitters
•Coaxial connections
•Creates signals from one signal source •Useful in
connecting picture-in-picture TVs with a cable box
Fig.
A
B
C
Order #
M61000
M61001
M61002
Description
2-way
3-way
4-way
(1-9)
$0.99
1.95
2.19
Splitter/Combiner
The Channel Plus
bi–directional
splitter/combiners
provide a 1GHz bandwidth
and are ideal for antenna
and coaxial cable operations. It can be used to split a
signal from a source or combine signals from multiple
sources onto one coax run.
Order #
2512
2514
2538
NET 30
Terms
Description
2–way
4–way
8-way
Insertion
Loss
3.5 dB
8.0 dB
12.0 dB
DC & IR
Passing
Yes
Yes
No
(ea.)
$5.09
7.49
10.29
207
13
•Zinc die-cast mounting •Provides
connection to stereo tuner for MTV
and other FM broadcasts usually
available on cable TV lines
B
A
A
Directional Taps
Blonder Tongue offers a complete
line of professional quality,
economical indoor directional
couplers and tapoffs with
frequency coverage to 900MHz.
Several models are available
with four way taps in varying attenuation values.
13
RF Splitters
Blonder Tongue offers a complete line of professional
quality indoor/outdoor couplers and tapoffs covering
frequencies up to1000MHz. These products are
available in both an L or T style cases. The variety of
loss values offered guarantees that they have the right product
for your application. These products feature a durable outdoor
rated soldered back, cast housing, which shields against
EMI and RFI disturbances.
Order #
Loss (dB)
A. L Style-SCW models
33-2941
4
33-2946
6
33-2951
9
33-2956
12
33-2961
16
33-2966
20
33-2967
24
33-2968
27
33-2969
30
section
C53_pg_208-209
section
13
8/13/08
10:21 AM
Page 208
SATV/CATV
Filters
Antenna Amplifiers
Low Pass Filters
TITAN 2TM Mast Mounted Preamplifiers
The Titan range of mast mounted
amplifiers has been completely
re-engineered and updated. These
amplifiers represent the ultimate
in preamplifier performance. They
are designed for use as an ultra low
noise, ultra high gain preamplifier
for deepest fringe applications and
MATV headend applications. Their
very high signal handling also makes
them suitable for use as a mast
mounted, ultra low noise distribution amplifier for use in small MATV systems. Both models feature 75ohm, input
and output connections in line with modern headend engineering practice. Models 7777 and 7778 cover both VHF
and UHF bands with separate amplification in each band for maximum signal handling. They may be configured
for either separate or combined VHF and UHF inputs. They include a switchable FM trap.
Order #
33-8960
33-8965
Mfr. #
7777
7778
Input
UHF/VHF
UHF/VHF
VHF Gain
23dB
16dB
UHF Gain
26dB
23dB
(ea.)
$62.95
65.95
In-Line Amplifiers
Specifications: •Bandwidth: 5~950MHz
•Gain: 11dB •Maximum input: 20dB
•Maximum output: 31dB •Noise figure:
4dB •Power requirements: 15VDC
•Dimensions: 21⁄2" (L) x 5⁄8" (dia) #33-910
DC Passive: For satellite 70MHz in-line
amplification when power dividers, low
gain LNAs and down convertors require
additional gain. #33-917 Non-Passive:
For MATV/CATV applications when
antenna preamplification and line
amplification is required. #33-915 Power
Supply: Provides power supply (15VDC)
and diplexer for #33-917 and 33-910.
#33-917
#33-910
13
#33-915
Order #
33-917
33-910
33-915
Type
Non-Passive Amp
DC Passive Amp
Power Supply
(1-9)
$12.95
13.95
14.29
(10-up)
$11.41
11.93
13.29
ChannelMax® Outdoor Antenna Amplifier
Amplifies weak UHF/VHF television signals. Increases incoming signal by
20 times. Consists of antenna boom mounted amplifier, UL/CUL listed power
supply, 6' RG-59 coaxial cable, weather boot. Packaged in a clear, clam shell
blister pack for optimum consumer appeal. Specifications: Frequency range:
54-88MHz 174-806MHz. Impedance: 300ohm (in), 75ohm (out). Gain: 13dB.
Power required: 120VAC.
Order #
33-8945
Mfr. #
3039
(ea.)
$34.95
Outdoor Mast Mounted Amplifier
This powerful UHF/VHF antenna
signal amplifier is designed to
overcome signal loss related to long cable runs, splitters,
and junctions. While an amplifier will not create a signal,
it will increase its power and minimize disruptions. Kit
includes mast mount amplifier, 110VAC power inserter,
and 6' coaxial cable. Frequency range: 40~862MHz.
17db gain. Mfr. #PA-17.
Order #
30-2091
(ea.)
$49.95
In-Line Amplifier
DC line powered amplifier for CATV or antenna applications.
Bandwidth is 5~950MHz. Gain is 10dB. Use with #33-915 power supply.
Order #
33-2690
208
(1-9)
$6.96
1-800-543-4330
Fax 1-800-765-6960
(10-up)
$6.44
The filter removes all CATV
channels above the pass band, allowing insertion of
locally generated channels. In addition, the filters
remove cable system noise which degrades the
picture quality of the locally generated channels.
Order #
LPF-380
LPF-470
LPF-600
LPF-750
Pass Band (MHz)
40~380MHz
40~470MHz
40~600MHz
40~750MHz
(ea.)
$19.00
20.00
32.95
30.00
Notch Filter
Designed to eliminate television channels 64 through
70 thus allowing a clean section of the cable to insert
locally generated signals. The center of the notch is
channel 67 at -55dB.
Order #
NF64-70
(ea.)
$25.00
75ohm TV
Interference Filters
•Used in cable or
antenna systems
to remove interference affecting picture quality
Order #
33-0070
(1-9)
$2.79
(10-99)
$2.41
(100-up)
$1.89
Voltage Blocking Coupler
•Blocks DC and low frequency
AC power •Solid brass body with
nickel plating •Female to male fittings
•22 gauge spring steel center pin •1~1000MHz
bandwidth •16dB return loss •0.3dB insertion loss
Order #
33-0020
(1-9)
$2.69
(10-up)
$2.39
FM Trap
Audio from the FM band
can overcome the audio on
adjacent television channels
6 and 7 and harmonics of the FM carrier. The FM trap
eliminates the entire FM band from 88 to 108MHz
reducing video noise and audio interference.
Order #
33-341
(1-9)
$2.69
(10-49)
$2.69
(50-up)
$2.39
Cable Modem Isolator
Separates and isolates
noise/EMI caused by
higher cable modem
transmission signals.
Improves internet
download reliability and
reduces cable modem “sync”
problems. Easily plugs into
coax wall jack allowing dedicated
runs to a cable modem and TV tuner. •Frequency
range: 10~770MHz •Insertion loss: <5.0db.
Order #
33-10395
(ea.)
$5.99
C53_pg_208-209
8/13/08
10:22 AM
Page 209
SATV/CATV
Indoor Antennas
Terk indoor HDTV
directional antennas
are optimized for HDTV
reception. Both UHF and
VHF elements are uniquely
designed for reception of all
available HDTV off-air broadcasts (channel 2~69).
Highly directional UHF elements reduce signal
interference and improve average return loss
for better reception and superior performance.
Mfr. #
HDTVi
HDTVa
Description
Non-amplified
Amplified
(ea.)
$37.95
52.95
UHF/VHF TV Antenna
•Dipoles extend to 30" •Dual UHF
loops •Brass with polished chrome
finish •Black base with 33" lead length
Order #
30-655
(1-9)
$5.07
(10-up)
$4.17
Panasonic Type Dual Antenna
Ideally suited for
indoor HDTV off-air
reception, this indoor
HDTV antenna features
a low-profile boom design,
rotational elements for
improved directional gain,
and a 7~13dB adjustable
gain control (power
adaptor included).
Order #
30-2100
(ea.)
$19.95
VHF/UHF/FM/HD Digital Indoor Antenna
•Replacement antenna for Panasonic,
RCA, JC Penney, Quasar and various
private brand TV sets •Five section •91⁄2"
collapsed •39" extended •21" lead length
Order #
30-060
13
HDTV Indoor
Amplified
Antenna
HDTV Indoor Antennas
Order #
30-2000
30-2005
section
•12 position fine tuning for best reception •34" telescoping dipoles
for VHF reception (channels 2~13) •UHF loop (channels 14~69)
•6' coaxial cable
(1-9)
$6.12
(10-up)
$5.91
Order #
MANT210
(1-4)
$11.95
Indoor Antenna
•Adjustable/retractable VHF dipoles extend up to 39" to improve
reception of channels 2~13 •UHF loop for improved reception of channels
14~69 •HDTV compatible •Attached 3' 75ohm coaxial hook-up cable
with “F” connector for easy hook-up •Off-air reception of local channelsanalog or digital •No-scuff pads protect cabinet/TV top •Dimensions:
12.7" (L) x 7.1" (W) x 3.0" (H)
Order #
ANT1020
(ea.)
$4.99
(ea.)
$9.42
AM Loop Antenna
AM/FM Tower
Positioned vertically, the
tower receives signals from all directions
with equal strength. Used horizontally,
it becomes highly directional to pull
in weaker and more distant stations.
It also distinguishes between signal
reflections and the main signal to
eliminate overload and multipath
difficulties. Specifications: FM stereo
section: •Amplifier gain: Variable
0dB~25dB •Impedance: 75ohm adaptable
to 300ohm input with included matching
transformer •FM operating band:
88~108MHz AM stereo section: •AM
operating band: 500~1700KHz •AM gain:
15dB •Range: 360° 17" (H) x 31⁄4" (W)
Order #
30-1110
(1-9)
$21.95
AM Advantage
The AM Advantage antenna
is a passive, fully adjustable
indoor AM antenna designed
for extended range capability.
The antenna is intended to
receive AM frequencies
530KHz~1600KHz for local
and distant AM reception.
The antenna features Pin–Dot™ Pre Tuning system
which allow the user to adjust the antenna and match
it to the specific frequency. Mfr. #ADVANTAGE.
Order #
30-1395
FM PRO 50
AM/FM Q
(ea.)
$63.95
(ea.)
$39.95
(10-up)
$19.95
Designed to provide exceptional long-range FM
reception, it may be mounted indoors or outdoors.
Advanced Capture Circuitry™ (ACC) ensures that
strong signals are locked in and weaker broadcasts
are received with less noise. Terk’s exclusive Dual
Drive Amplifier boosts signals above noise and
interference, using a DC–driven phantom power
supply that is easily connected to your receiver.
TERK’s premium amplified
indoor AM/FM antenna. The
AM/FM Q features TERK’s
unique Pin-Dot Pre-Tuning
that zeroes in on even
hard-to-get stations by
tuning the antenna to the
station’s frequency. Mfr. #AF-1.
Order #
30-1550
13
Order #
ANT110
Indoor Antenna
•Digital TV compatible •VHF/UHF/FM •39" retractable dipoles
adjust for best reception •UHF loop •6' 75ohm hook–up cable
with screw–on “F” connector
(2-4)
$61.95
(5-up)
$58.95
Order #
30-1205
(ea.)
$95.95
www.mcmelectronics.com
•Popular replacement
AM antenna used on
most stereo receivers
•181⁄2" lead length •300ohm impedance •Antenna
has two pin quick connect for equipped systems
•For systems with push terminals or screw terminals,
simply cut and strip the ends of the antenna wire
for your application
Order #
30-660
(1-9)
$3.59
(10-up)
$3.39
FM Dipole Antennas
These high quality FM
dipole antennas can be
used for many newer
FM tuners and receivers.
Available in three
configurations: 300ohm
spade terminals, 75ohm male “F” connector and
75ohm female PAL connector. These antennas are
constructed from high quality 300ohm twin–lead and
perform significantly better than the OEM supplied
straight wire or a split two conductor antennas
providing higher quality FM reception.
Order #
30-1530
30-1535
30-110
NET 30
Terms
Description
Male “F” connector
Female PAL connector
Spade terminals
(1-9)
$2.29
1.69
1.69
(10-up)
$1.59
1.19
1.49
209
C53_pg_210-211
section
13
8/13/08
10:23 AM
Page 210
SATV/CATV
Outdoor Antennas
#30-840
#30-2065
#30-2066
#30-850
#30-2067
UHF/VHF/FM Antennas
•300ohm output, includes 75ohm transformer
#30-1071
Multi-Directional HDTV UHF Antennas
Boom
Order # Description
Length Elements (ea.)
30-840 Colorstar 480
150"
48
$68.95
30-850 Color King 5884 58"
25
32.95
Multi-directional antennas are designed to work in locations
where the transmitters for digital stations are spread apart.
These popular HD antennas utilize a bowtie design that provides a strong gain
across the entire UHF spectrum (channels 14~69). They function incredibly well
in areas where flexible aiming is required and feature a weatherproof construction
that resists extreme wind loading.
Range
Miles
Order #
Description
30-2065
30-2066
30-2067
Indoor/outdoor, low-profile, short range 1~30
Outdoor, most popular, mid-range
15~55
Outdoor, high-gain, long range
50~70
Gain
11.4db
13.7db
15.8db
Dimensions
(H) x (W) x (D)
12" x 19" x 4"
29" x 19" x 4"
29" x 42" x 4"
#30-2070
(ea.)
$39.95
58.95
94.95
13
These powerful, weather-resistant, outdoor
antennas are ideal for medium to long range
applications that require the gain of the
antenna to be concentrated in one direction.
The Yagi style design effectively rejects off
#30-2072 axis signals from structures that cause
multi-path interference, and the corner reflectors on the back of the antennas
improve the forward gain of the antenna resulting in exceptional performance
across the entire UHF spectrum (channels 14~69).
Range Gain Dimensions
Order # Description
miles
db
(H) x (W) x (L) (ea.)
30-2070 Compact, 15-element, short-range
1~30
11.0 14" x 13" x 35" $47.50
30-2071 Mid-sized, 43-element, long-range
15~60
15.7 19" x 18" x 62"
63.95
30-2072 Large, high-gain, 91-element, long range 50~70+ 16.7 22" x 20" x 93"
94.95
#PR-7015
210
#30-1655
#30-1660
#30-1665
VHF Elements
9
12
17
21
Advantage Series Antennas
The Advantage line of antennas was designed with the Do–It–Yourself installer
in mind. All models are UPS shippable and will fit in most any vehicle. Superior
performance, economy, pricing, and pre-assembled for ease of installation, make
this antenna line the perfect choice for the self-installer. Includes balun, weather
boot and S clip.
Order #
30-1635
30-1640*
30-1645
30-1655
30-1660
30-1665
*Limited quantities
Mfr. #
3020
3019
3018
3016
3014
2001
#CA-7082
•300ohm output •Digital ready •Die cut impedance
correlators allow close spacing of antenna elements #PR-7052
manufactured from high tensile aluminum that will
withstand strong wind and ice •Aluminum is protected with high quality polymer
finish to protect for oxidation •Exlusive wrap-around mast clamps can not crush
antenna or boom mast •Completely automatic hardware
Active Elements
22
31
43
49
#30-1645
Boom Length
152"
133"
113"
66"
52"
27"
(ea.)
$99.95
104.81
69.95
45.95
32.95
24.95
#PR-7042
Prostar 1000
VHF/UHF/FM Antennas
Order #
PR-7010
PR-7015
PR-7042
PR-7052
#30-1640
#30-2071
Uni-Directional HDTV UHF Antennas
#PR-7010
#30-1635
UHF Elements
13
19
26
28
Boom Length
16.5"
87.75"
149.75"
170.25"
(ea.)
$99.95
84.95
145.00
169.00
Chromstar 2000 VHF/UHF/FM Antennas
•75ohm output •1dB to 2dB higher gain on VHF and UHF for improved picture
quality •Zinc plated steel hardware •Polyethylene boot covers keep connections
clean and dry •Aluminum is protected with a high–quality polymer finish to
protect from oxidation
Order # Active Elements
CA-7082
50
CA-7080
39
1-800-543-4330
Fax 1-800-765-6960
#CA-7080
VHF Elements
18
14
UHF Elements
32
25
Boom Length
110.5"
90"
(ea.)
$135.00
149.75
C53_pg_210-211
8/13/08
10:24 AM
Page 211
SATV/CATV
Outdoor Antennas
section
13
UHF Indoor/Outdoor Antenna
Easiest and best solution for
urban/surburban UHF DTV (digital TV)
reception. Perfect alternative to conventional
outdoor antennas. Features: •Built-in
optimum gain amplifier, 18dB UHF, with low
noise circuitry, under 3.5dB, for best possible
DTV performance •Efficient flat panel UHF
array, up to 40 miles range •Compact yet
effective size, 5" x 10" •Easily mounts on
wall, mast or railing •Can be used with
rotor (optional, mast only) •Ideal for RV
or boat. Includes 20' cable, power injector,
power supply, and flexible mounting kit.
Order #
MANT940
Omni–State
Omni–Directional Antenna
The Omni–State antenna provides
excellent reception of VHF and UHF
channels in most viewing locations.
Measures 21" in diameter and
has a 20dB built–in amplifier.
Operates on 120VAC with
the supplied adaptor.
Order #
30-1335
(1-4)
$39.95
Amplified, Satellite Dish
Mounted, Clip-On TV Antenna
HDTV Amplified Outdoor Antenna
The Terk HDTVo is an innovative,
compact, amplified outdoor antenna that features
powerful high gain, and offers versatile installation
flexibility. Its unique design incorporates a highly
directional log periodic antenna array and a pair of
curved elements that combine to capture and focus
HDTV signals. Mount flush to the side of a building,
or use the included mulit-mount mini-mast and base
to install virtually anywhere.
(ea.)
$114.00
A
Practically invisible, these
mini antennas have a powerful
magnetic base with rubberized
feet to facilitate versatile
mounting and placement
C
without drilling into the vehicle
surface. Each antenna is for exclusive use of XM or
Sirius satellite radio receivers. Dimensions: 1.37" (W)
x .5" (H) x 1.25" (D).
Order #
33-10365
33-10385
33-10371
Description
Cable Length (ea.)
XM Antenna
23'
$29.95
Sirius Antenna
21'
39.95
Amplified extension cable 50'
39.95
Mfr. #
TV-44
(ea.)
$58.95
Sirius™
Satellite Radio
Outdoor Antenna
Maximize the
signal strength of your
SIRIUS™ dedicated home, or plug-and-play single
input receiver/ radio. This all-weather antenna can be
mounted on an exterior wall or roof with the supplied
universal mounting bracket and hardware. The SIR6
comes with a 30' detachable cable to facilitate easy
cable routing and hook-up. Dimensions: 33⁄16" (W) x
43⁄4" (H) x 125⁄16" (D). Mfr. #SIR6.
Order #
(ea.)
33-10390
$79.95
FM Turnstyle
Scanner Antenna
Covers VHF/UHF public service
bands 30~1300MHz. Includes 300 to
75ohm matching transformer and 50'
RG-6 coax cable.
Order #
30-1380
Order #
33-9655
B
Satellite Radio
Replacement
Antennas
Fig.
A
B
C
Now you can keep the great satellite programming
you have, pick up local HD stations not currently
available from service providers and get free local
programming too with the TERK TV44. The TV44
has a patented clip on design that attaches directly
to your satellite dish without any tools. The TV44
was developed to be weather resistant, ensuring
years of enjoyment, and its internal amplifier
minimizes signal loss for the best reception possible.
(ea.)
$42.95
•Offers the gain of a
folded dipole with an
omni–directional pattern
•Works in areas where
stations are situated in
many directions
Order #
30-855
(ea.)
$21.95
www.mcmelectronics.com
STEALTHtenna™ UHF/VHF Antenna
Optimized for HDTV/digital and analog reception,
the STEALTHtenna offers the performance and
aesthetics that today’s consumers demand for
their ever changing reception needs. Rear mounting
bracket design allows the STEALTHtenna to be
easily installed under an eave for an inconspicuous
installation. STEALTHtenna may also be mounted in
traditional roof, chimney, wall and attic configurations.
Optional amplifier provides split band amplification
and is optimized for HDTV/digital as well as analog
signals. Specifications: Gain: 15dB UHF, 15dB
VHF/FM. Power 12~22VDC via included adaptor.
Order #
30-1715
30-1720
Mfr. #
3010
3038
Description
Stealthtenna
Stealthtenna amplifier
(ea.)
$37.95
29.95
UHF/VHF/FM Indoor/Outdoor Antenna
This versatile antenna is designed to look as great
as it performs. Use it indoors or out for superior
reception in urban or suburban areas. Lightweight,
compact and easily mountable, it’s equally at home
on your roof or patio rail, in your attic or family room.
Features: •Dual element for best reception and
range, up to 40 miles •Superior reception over
UHF and VHF bands •Ideal for both today’s
analog reception and the future’s digital TV (DTV)
•18dB/VHF, 15dB/UHF amplifier gain for extended
reception range •Low noise amplifier maintains
carrier-to-noise ratio, critical for DTV •Can be
used with rotor (optional, mast only). Includes
hardware, power supply and 20' cable.
Order #
MANT950
(1-4)
$85.95
TV55 Antenna
The TV55 indoor/outdoor amplified antenna
is optimized for HDTV reception. The TV55’s
helical coil technology and patented dual–mode
ultra–low–noise amplifier provide clear, powerful
reception of HDTV and analog VHF/UHF broadcast
signals, and its slim-profile design allows easy
mounting under a windowsill, on a rooftop, on a
wall or in any number of locations inside or outside
a home. The TV55 includes cables and weatherproof
stainless steel connectors. The kit combines local
and satellite signals into a single RG-6 coaxial cable,
eliminating the need to run an extra wire from the
dish to the home. Accessories included: (1) power
injector with 110VAC to DC power adaptor, mast,
wall and window mount hardware, (1) 93⁄4" flat coaxial
cable, (1) 36" RG-6 coaxial cable. Mfr. #TV-55.
Order #
30-1525
NET 30
Terms
(ea.)
$73.95
211
13
Order #
30-2020
(ea.)
$74.95
C53_pg_212-213
section
13
8/13/08
10:25 AM
Page 212
In-Line Surge Protector
SATV/CATV
Protect your cable modem,
tuner, convertor, decoder, and
satellite receiver from power
surges and spikes caused by
lightning strikes. Plugs
directly into coax line. Specifications: •Frequency
range: 5~2,400MHz •Insertion loss: 1.5dB max
•Max surge current: 5000A
Antenna Rotator
with Memory and
Remote Control
The remote controlled antenna rotator with
12 position memory is ideally suited for use
in today’s home
theater systems.
Micro–processor
control allows for
up to 12 memory
positions to be
stored. Dual
display shows
both direction and memory position. Uses
standard three conductor rotator wire (#24-3080).
Order #
30-1101
(ea.)
$84.95
Order #
33-10400
(1-9)
$6.39
Double Galvanic
Lightning Arrester
Protects your valuable video
equipment from voltage surges
caused by lightning strikes to
or near antennas or cable
television lines. Frequency
range: 5MHz~1GHz.
Order #
33-8695
(1-9)
$5.19
•Mounts TV antennas without
guy wires •Self supporting •Extra
heavy–duty with rotamast feature
•Fits mast up to 13⁄4" •Six screw
mast support
Order #
30-925
30-930
Size
3'
5'
Antenna Rotator
(ea.)
$29.95
32.95
Designed for outdoor antenna use and can
be used on the roof or side of the house. The
mount foot can be used on either end of the
pipe for most efficient mounting. •Galvanized
steel • 38" long •Wall thickness: .060" •1.66"
OD and E–Coated for maximum protection.
(ea.)
$79.95
Order #
DS-3000
C
Ground Clamps
A properly grounded antenna or satellite system
will not suffer from the effects of ground loops.
These ground loops can be identified as beat and
herringbone in the picture. Available in 3⁄8" and 5⁄8"
for connecting to ground rods and two piece clamps
for connecting to 1⁄2" to 1" water pipes.
Fig.
A
B
C
Order #
33-6895
33-6900
33-6905
Diameter
⁄8"
⁄8"
1
⁄2"~1"
(1-9)
$1.79
2.09
2.89
3
5
(10-up)
$1.25
1.64
2.46
High Frequency
Ground Blocks
High frequency
ground blocks
have extended frequency capacity to 2.4GHz making
them perfect for satellite and digital applications.
Nickel plated finish to resist effects of the weather.
Order #
33-7705
33-7710
(ea.)
$31.95
(2-up)
$27.95
Description
Single
Dual
(1-9)
$0.59
2.07
(10-99)
$2.03
(100-up)
$1.93
Grounding Block
“J” Pipe Mount
•Heavy-duty motor handles large antennas •Extra
strong machine cut gears won’t bind •Brake pads
hold firm •Tested to 70 mph winds •Requires
three–wire rotator wire (#24-3080)
13
B
(10-up)
$4.81
Tripod
Roof Mounts
Order #
30-1020
A
•Zinc die-cast •Mounting
screws included.
Order #
33-470
33-1800
Description
Single
Dual
(ea.)
$0.82
2.69
Ground Wire
Type THHN wire commonly used as ground wire.
10AWG stranded or solid copper with oil and gas
resistant coating. Available in stranded and solid.
Order #
24-5365
24-5375
Description
Stranded, 500' spool
Solid, sold per foot
(ea.)
$129.94
1.11
(2-up)
$0.88
TennaMount
A strong stable mounting
system that supports both DBS
and VHF/UHF antennas in one
convenient location. Installs
quickly and easily to the side
wall of a building, and adjusts
easily to roof overhangs. All
mounting hardware supplied.
Economical Antenna Rotator
Our economical antenna rotator helps improve
TV and FM reception. Two piece connects via three
wire rotator cable. Adjustable clamp accommodates
mast up to 11⁄2".
Order #
30-1100
Order #
33-2630
(ea.)
$63.95
(ea.)
$52.02
4' x ⁄ " Universal Grounding Rod
3
8
The 4' universal grounding rod is ideal for completing
your system installation. The copper coated steel
construction prevents ground loop problems.
Order #
33-9700
(1-9)
$5.49
Eve Mounts
Rotator Cable
Three conductor cable for use with many popular
antenna rotators. Outer jacket 0.162" black PVC
with 0.020" wall. Three 20AWG conductors color coded black, white and red.
Order #
24-3080
24-3085
24-3090
Length
100'
500'
1000'
(ea.)
$25.95
111.00
199.00
(2-4)
$22.34
101.94
183.49
Alternative to roof and
chimney mounts. Fits most any medium pitch roof. Adjusts from 43" to 60".
Accepts up to 11⁄2" masts. Includes mounting hardware. Zinc finish.
Order #
30-1085
(5-up)
$20.80
94.25
169.65
Guy Wire
•18 gauge, 6 strand heavy-duty guy wire •Vinyl
coated to reduce effects of weather •Length: 100'
Order #
30-1055
212
(ea.)
$22.17
(ea.)
$11.95
1-800-543-4330
Fax 1-800-765-6960
MiniMount
The low profile design attaches easily to the top of a roof
mounted antenna pipe stand, providing a stable mounting
point for any small VHF/UHF TV antenna.
Order #
33-2626
(ea.)
$18.13
C53_pg_212-213
8/13/08
10:25 AM
Page 213
SATV/CATV
SlimLine Coupler
This flat, flexible coupler allows you to run
cables into a house or apartment without
drilling holes in the window frame of the
house. Simply put the cable through the window and close,
the coupler will bend easily around the window pane.
Order #
33-7430
A
D
B
E
C
F
section
13
(ea.)
$8.29
Masts
16 gauge corrosion protected mast ideal for television and communication antennas.
5' section swagged at one end. 21⁄2' section ideal for use above rotator.
Order #
30-1080
30-935
Size
21⁄2'
5'
(ea.)
$6.99
11.95
A
B
AntennaMounting Hardware
Fig.
A
B
C
Order #
30-1030
30-1035
30-1045
Description
Guy wire clamp up to 11⁄2" mast
Turnbuckle - 7" open, 5" closed
Cable clamps 1⁄2" open 1⁄8" closed
Qty.
1
3
3
(pkg.)
$3.58
4.09
1.53
C
Heavy–Duty Antenna Mounting Accessories
U-Bolts
•Heavy–duty mount for masts up to 11⁄2" outer
diameter •Made of all steel construction •Triple coat corrosion protection
Fig. Order #
Description
(ea.)
Fig. Order # Description
(ea.)
A 30-895
Roof mount
$6.65
D 30-910 “Z” chimney mount $10.24
B 30-900
4" wall mount
6.65
E 30-915 “Y” chimney mount 22.95
C 30-905
8" wall mount
7.68
F 30-1160 Vent pipe mount
10.24
Connects antennas or mast to bracket. Use with mast pipe up
to 11⁄4". One per package.
Order #
30-1515
(pkg.)
$1.99
CATV Security Tool
•UHF/VHF/FM
75~300ohm matching transformer •“F” type input,
300ohm twin lead output •Minimum five
•UHF/VHF/FM
75~300ohm adaptor
•“F” type input, twin
lead output •Ten per
bag, bulk packaged
Order #
33-050
(5-9)
$1.19
(10-99)
$1.07
(100-up)
$0.89
Outdoor
Order #
33-040
Order #
33-220
33-200
Input
Ohms
75
75
VHF
Ohms
75
300
UHF
Ohms
300
300
FM
No
Yes
(1-9) (10-49)
$4.09 $3.57
3.29
2.57
•Quick connect for “F” fittings
with impedance matching
transformer •Minimum five
(5-9)
$0.84
(5-9)
$2.04
(10-49)
$1.71
(50-up)
$1.39
TV Line Clips
Order #
33-610
(10-up)
$0.63
(1-9 pkgs.)
$1.24
(10-49 pkgs.)
$1.06
(ea.)
$7.09
0.54
Make cable runs neat and easy. Made
of high impact plastic with plated steel
nails. Firmly attaches cable to wood,
plastic, brick, mortar or concrete block.
100 per package.
Order #
33-585
33-580
33-4745
33-4750
33-4765
33-4770
•For antenna lead hook–ups
•High–quality construction
•For quick connection of
300ohm twin lead to
antenna terminals •Two per package
Push-On Balun
Order #
33-010
(1-4)
$2.18
Description
Security tool
Security sleeve
Cable Clips
•Weather resistant, molded plastic
construction •Supplied with rubber boot
Antenna Signal Splitters
•Precision machined,
high-quality security tool for
connecting and disconnecting
cables protected by a security
sleeve •Long shaft fits all
types of sleeves
Order #
33-0025
33-0030
Order # (1-3 bags) (4-9 bags) (10-24 bags) (25 bags-up)
33-1390 $7.50
$6.99
$6.50
$6.31
13
Indoor
Economical Indoor
Matching Adaptor
Color
Black
White
Black
White
Black
White
Cable
(1-9 pkgs.)
RG-59
$3.89
RG-59
3.44
RG-6
3.39
RG-6
3.58
Dual RG-6
3.65
Dual RG-6
3.65
(10 pkgs.-up)
$3.19
2.90
2.85
3.01
3.11
3.02
(50-99 pkgs.)
$0.85
Feed-Thru Bushings
COAX-SEAL
Pitch Pad Kit
•A fast and easy way to waterproof
coax fittings •Wraps around fittings
and can be molded to any shape
•Works with vinyl and poly vinyl
outer covers •Stays flexible for years
•Pitch pad and lag bolt
kit •Pads reduce risk of
water leakage •Use when
mounting antennas on roof
•Contains six lag bolts
Order #
30-940
(kit)
$3.06
Order #
21-1140
(1-9)
$3.79
(10-24)
$3.39
(25-49)
$3.19
www.mcmelectronics.com
Cable feed-thru bushings give cable and satellite
installations a finishing touch. Available in single and
dual construction, white or black. 100 per package.
Order #
33-4815
33-4820
33-4825
33-4830
NET 30
Terms
Description
Single, white
Single, black
Dual, white
Dual, black
(1-9 pkgs.)
$4.39
4.39
5.49
5.49
(10-up pkgs.)
$3.99
3.99
5.09
4.89
213
C53_pg_214-215
section
13
8/13/08
10:27 AM
Page 214
SATV/CATV
HDMI to Component
Video Convertor
4 x 1 HDMI Switch
with Digital Audio
HDMI Pattern Generator
The ExtenHD™ X-GEN Pro is an HDMI signal
generator that allows the user to select one of over
35 signals at various frequencies in order to generate
a true HD signal for testing, confirmation and system
set-up. Features: •RS-232 port for loading your
favorite set-ups or integrating into a remote control
system for off-site diagnosis •On/off HDCP signal
generation for testing critical components •Generates
patterns in 4:2:2, 4:4:4 YUV, and 4:4:4 RGB format
•Audio insertion into HDMI stream with tone
generator function •Backward compatible with DVI
•Rack mountable •Includes IR remote control and
Windows software application for advanced controls,
such as auto programming for timing/pattern, EDID
reading and EDID updating.
Order #
33-10435
Mfr. #
X-GEN Pro
The ExtenHD™ X-SW41 allows up to four HDMI
sources to share one HDTV display. It also has
audio input/output connections to facilitate system
designs that switch audio signals through an existing
audio system, or a separate PA/distributed audio
set-up. Features: •HDMI 1.2, HDCP 1.1 and DVI
1.0 compliant •Signal enhancement feature allows
you to improve signal quality after long distance
transmission •High resolution support up to UXGA
(1600 x 1200) and HDTV 1080p •1⁄2 rack set-up
(optional). Specifications: •Frequency bandwidth:
1.65Gbps (single link) •Inputs: 4 x HDMI female
ports (Type A connector), 4 x SPDIF digital inputs,
4 x toslink digital inputs •Output: 1 x HDMI female
port (single link), 1 x SPDIF digital output, 1 x
Toslink digital output •RS-232-DB-9 •Power
supply: 110~220VAC input, 5VDC output
Order #
33-10455
33-10475
Mfr. #
X-SW41
1
⁄2 rack mount
(ea.)
$299.00
79.00
The ExtenHD™ X-CON is an HDMI to component
(YCbCr/YPbPr) convertor with audio output. It allows
you to switch between two HDMI sources and convert
it to component and analog audio (L/R) or digital
audio output at the same time. It supports output
resolutions equal to the source input up to 1080p.
Features: •Compliant with HDMI 1.2a, HDCP 1.1
and DVI 1.0 specifications •Supports a wide range
of resolutions up to 1080p at 50/60Hz •Supports
digital audio output (coaxial), or analog audio
output (L/R line level) •1⁄2 rack set-up (#33-10475).
Specifications: •Input: 2 x HDMI female ports
•Video output: Component YPbPr/YCbCr on three
RCA jacks •Audio: Digital audio on coax, or analog
audio on R/L •Power: 5VDC power supply (included).
Dimensions: 215 (W) x 112 (D) x 42 (H) mm. Note:
•When input is HDCP Encrypted (protected) the
component output will be turned off.
Order #
33-10440
33-10475
Mfr. #
X-CON YUV
X-RK
(ea.)
$299.00
79.00
2 x 1 HDMI Switcher
•Switch between any two HDMI inputs •Compatible with any HDMI
source •Supports up to 1080p resolutions and is HDMI, HDCP and DVI
compliant Features: •Two HDMI Inputs, one HDMI output •Signal
enhancement feature; improve signal quality of longer cable runs •LED
power,enhancement and source indicator lights •Manual input selection
with buttons on unit Includes: •HDMI switcher and AC adaptor
(ea.)
$899.00
Order #
80-6860
Mfr. #
VS-H21
(1-9)
$79.95
(10-up)
$74.55
Front
13
HDMI to HDMI Signal
Equalizer/Extender
The ExtenHD™ X-EQ equalizes the HDMI
signal after 20 meters, injects an 8db gain to boost
the HDMI signal path up to an additional 20 meters
(40 meters overall) and corrects the digital error
associated with extended HDMI cable runs ensuring
a bright, clear, high definition picture on your
display. Supports HDTV resolutions up to 1080p,
and PC resolutions up to UXGA/165MHz. Features:
•HDCP compliant •Can be powered directly from
the cable, or from external power supply (included;
recommended) •Backward compatible with DVI
•Easy to install •RoHS compliant. Specifications:
•Input: HDMI jack •Output: HDMI jack
•Power supply: 110~220VAC input; 5VDC
output •Dimensions: 2.83" (W) x 3.0" (D) x
1.18" (H) •Weight: 1⁄2 lb.
Order #
33-10445
Mfr. #
X-EQ
(ea.)
$199.00
Back
4 x 1 HDMI Switch
•Four HDMI inputs,
one HDMI output
•Signal enhancement feature, improve signal quality
by simply touching a button •LED source indicator
light •Slim size IR remote included Specifications:
•HDMI 1.3b, HDCP and DVI 1.0 compliant
•Supported input resolutions: PC - VGA, SVGA, XGA,
SXGA, UXGA (1600x1200), HDTV -480i, 576i, 480p,
576p, 720p, 1080i and 1080p •Frequency bandwidth:
1.65gbps (single link) •Inputs: Three HDMI type A
female ports •Output: HDMI single link female port
•Dimensions: 7.9" x 4.1" x .9" •Weight: 1.25 lbs. •5V
universal power supply included •Mfr. #V5-HD41
Order #
33-10485
(1-9)
$79.95
(10-up)
$78.25
1 x 4 HDMI Distribution Amplifier
•One HDMI input, four HDMI outputs •Signal
enhancement feature improve signal quality by
simply touching a button •LED indicator light on
each output •Slim design, less than 1" thick! •Slim
size remote included Specifications: •HDMI 1.1,
HDCP 1.1, and DVI 1.0 compliant •Supported input
resolutions: PC - VGA, SVGA, XGA, SXGA, UXGA
(1600x1200), HDTV - 480i, 576i, 480p, 576p, 720p,
1080i and 1080p •Frequency bandwidth: 1.65gbps
(single link) •Inputs: 1 x HDMI type A female ports
•Output: 4 x HDMI single link female port
•Dimensions: 7.9" x 4.1" x .9" •Weight: 1.25 lbs.
•5V universal power supply included
Order #
80-6840
1 x 8 Single-Source
HDMI Distribution Amplifier
HDMI over Category 5 UTP
ExtenHD™ transmitters and receivers work together
to allow HDMI digital signal path transmission over
Cat 5 or Cat 6 UTP cable (two cables required) up
to 250 meters. Used in pairs (sold separately),
the transmitter and receiver allow you to switch
between two HDMI source inputs. Features:
•Compliant with HDMI 1.2, HDCP 1.1 and DVI 1.0
specifications •Supports resolutions up to 1080p at
50/60Hz. Specifications: •Input: One HDMI female
port •Output: One Cat 5 (RJ-45) jack for video and
one Cat 5 (RJ-45) jack for DDC •Power: 5VDC power
supply adaptor (included) Dimensions: 123" (W) x
125" (D) x 30" (H).
Order #
33-10450
33-10451
33-10452
214
Mfr. #
X-CAT TRAN
X-CAT 50
X-CAT 250
Description
Transmitter
Receiver (50m)
Receiver (250m)
(ea.)
$259.00
239.00
649.00
The ExtenHD™ X-DA18 is a high performance
HDMI amplifier that not only extends one HDMI
source input to up to eight HDMI HDTV displays,
but can also be cascaded indefinitely. Each of the
buffered outputs can run up to 15 meters at 1600 x
1200 with no signal loss. Housed in a 1U rack
mountable case with removable rack ears, the
X-DA18 provides fast handshaking for quick
picture display, and is fully HDCP compliant.
Features: •HDCP key sets allow each output to
work independently when connecting to a HDMI
display •Supports high definition resolutions
up to 1080p and UXGA at 165MHz •Supports
multi-channel audio. Specifications: •Frequency
bandwidth: 1.65Gbps (single link) •Inputs: 1 x HDMI
jack •Output: 8 x HDMI jacks •Power supply:
110~220VAC input, 5VDC output •Mfr. #X-DA18
Order #
33-10465
1-800-543-4330
Fax 1-800-765-6960
(ea.)
$539.00
(1-9)
$442.00
2 x 10 Multi-Source HDMI
Distribution Amplifier
The ExtenHD™ X-210 is a high performance HDMI
splitter with separate optical audio housed in a
1U rack mountable case with removable rack ears.
The X-210 splits, amplifies and extends two HDMI
source inputs (eg. digital cable box, DVD player) to
up to ten HDMI HDTV displays (eg., HDTV, LCD
projector). Each of the buffered outputs can run
up to 20 meters at 1600 x 1200 with no signal loss.
Features: •HDCP keysets allow each output to
work independently when connecting to a HDMI
display •Supports high definition resolutions up to
1080p and UXGA at 165MHz •Fully HDCP compliant
•Supports multi-channel audio •Separate toslink
audio output •RS-232 control and front panel lockout.
Specifications: •Frequency bandwidth: 1.65Gbps
(single link) •Inputs: 2 x HDMI jacks, 2 x optical
audio input •Output: 10 x HDMI jacks, 2 x optical
audio output •Power supply: 110~220VAC input,
5VDC output •Mfr. #X-210
Order #
33-10460
(ea.)
$799.00
C53_pg_214-215
8/13/08
10:28 AM
Page 215
SATV/CATV
Are you ready for the 2009 DTV transition?
Beginning February 17th, 2009, all over-the-air television broadcasts will be
transmitted exclusively in high-definition digital frequencies. Any analog (NTSC)
televisions and tuners that pull their signal from an antenna will no longer be
able to decode broadcasts on their own. Only digital tuners (ATSC) will be able
to decode these free high-definition signals. Newer televisions and devices have
a digital tuner already built-in, but older devices will require an external ATSC
tuning device.
section
13
This changeover will free up communication frequencies that we need in times
of emergency and for modern everyday living. New digital signals also provide
a crystal-clear high-definition picture with 5.1 surround sound abilities.
The DTV change only affects over-the-air signals that are picked up by an antenna.
If you get all of your television programming from satellite, cable, or other
methods, this change will not affect you!
HDMI 1.3 Input Switch
See www.dtv2009.gov for more details.
Easily switch between multiple HDMI sources while
running a single HDMI cable to your high-definition
display. Extends the range of HDMI compliant device
by equalizing and re-clocking the HDMI signal.
Included discrete IR remote control allows user to
switch sources from across the room. Auto sensing
inputs allow switching between only active HDMI
sources. Specifications: •Output video: HDMI
1.3b + HDCP 1.0/1.1 •Video formats supported: Up
to VGA 920 x 1200 and HD 1080p •Video amplifier
bandwidth: 2.5Gpbs/250MHz •External power
supply (included): 2A, 5VDC for 110V
Front
Digital TV/HDTV ATSC Off-Air Tuner
Ideal solution for receiving terrestrial, off-air (antenna)
digital TV broadcasts from the constantly increasing
number of off-air digital TV broadcasters (e.g., local
stations, PBS, etc). Features: •ATSC receiver capable
of outputting composite, or component (Y.Pb.Pr) video
•Stereo audio output •Parental control-movie/TV rating
(V-chip) •Fully functional infrared remote controller
•Selectable SDTV/ HDTV output/input resolution
(480i/480p/720p/1080i) •Standard definition NTSC 480i
output •Aspect ratio control; 4:3 and 16:9 •Advanced
Electronic Program Guide (EPG)
Order #
33-10413
Description
ATSC tuner
Order # Description MSRP (1-4)
33-10532 2 x 1 $59.95 $39.95
33-10533 3 x 1
79.95 49.95
33-10535 5 x 1 109.00 69.95
(ea.)
$199.00
(5-9)
$38.75
48.45
67.85
(10-24) (25-up)
$36.75 $34.36
45.95 42.96
64.35 60.16
Back
A/V Switches
A/V Digital Analog Selector with IR Remote
Full-featured switcher connects up to three “like-kind”
sources (HDMI to HDMI, VGA to VGA, etc.) to a single HDTV
display. Features: •HDMI, VGA, RGB component video, and
composite A/V connections •Delivers clean, uncompressed
digital signals •Engineered for optimal signal transfer and
minimal signal loss •Built-in HDMI output signal extender
up to 100' (total length) •H.D.C.P. (High-Bandwidth Digital
Content Protection) compliant •Supports high definition
1080p and UXGA •Compact, time-saving LED illuminated
control center and easy selection with remote control or front
panel push-button controls •Power: 6V,400mA AC/DC power
adaptor (included) •Dimensions: 121⁄2" x 6" x 21⁄4".
Back
Front
(ea.)
$167.00
Easily switch between four HDMI sources to
two high-definition displays. Extends the range
of HDMI compliant devices by equalizing and
re-clocking the HDMI signal. Included discrete IR
remote control allows user to switch sources from
across the room. Specifications: •Input/output:
HDMI v1.3, HDCP 1.0/1.1 •Video formats
supported: Up to computer 1600 x 1200 and HD
1080p •Video amplifier bandwidth: 1.65Gpbs
•Power consumption: 20W (max) •External power
supply (included): 5VDC for 110V •Dimensions:
41⁄2" (L) x 15⁄16" (H, with feet) x 101⁄8" (W)
Order #
MSRP
(1-4)
(5-9)
(10-24) (25-up)
33-10525 $399.00 $199.00 $193.03 $183.08 $171.14
Back
HDMI Three-Way Switcher
Get the most out of HDTV! •Connect three HDMI sources to a single input on a TV •Automatically switches
to the selected source •Switch between sources without compromising the signal •Full 1080P transmission
•HDCP compliant
Order #
SWV6813/17
(1-4)
$99.95
Audio Video Switcher with Component Video
Back
Provides the necessary A/V inputs for adding components to your TV and home
theater system. Has five audio/video inputs including component video, S-video
and digital audio plus dual outputs to feed your TV and either a receiver or VCR
for recording. The VS-502 will help make the transition to HDTV easy! Features:
•Easy video conversion: Switch between three different video types including
up-converting composite to S-video and composite and S-video to
component video. •Auto input sensing: Detects the current unit in
use and automatically connects to that input, without having to push
any buttons! •Automatic volume stabilization: Volume compression
setting pulls loud and soft sounds toward a mid-point in the dynamic
range. •Two independent output channels: Two outputs let you select
one source for viewing (like the DVD) to watch on your TV and a second source
for recording (like the DSS) to feed to your VCR for recording at the same time.
Order #
80-6690
Mfr. #
VS-502
(1-9)
$195.00
High Definition Automatic Switcher
•Hook up multiple video game systems, DVDs,
VCRs, and any other A/V device to any TV that
lacks the required number of AV inputs •Four inputs
allow you to automatically switch between desired
components •Features four audio/video, S-video, and
component inputs; composite, S-video and component
out •Component inputs provide ultimate picture
performance and are found on most quality
TVs/HDTVs and DVDs •Easy to hook-up and
prevents cable swapping issues that could result
in the jacks on the TV needing to be replaced.
(10-up)
$190.00
www.mcmelectronics.com
Order #
PH61150
NET 30
Terms
(1-4)
$29.95
215
13
Order #
33-10424
HDMI 4 x 2Matrix Switch
C53_pg_216-217
section
13
8/13/08
10:28 AM
Page 216
SATV/CATV
RF Switches
Deluxe A/B Switch
Audio/Video Matrix Switcher
Video matrixes allow you to send audio/video signals from
any of the eight inputs to any of the eight outputs with the touch of a
button. The matrix can split the audio and video sources allowing you to add music to
a video dub. Control the operation from a PC via the RS-232C port. Genlock inputs provide steady
video signals for optimum picture quality. Specifications: Video: Composite input/output, 1V p-p, 75ohm. S/N
ratio: -60dB. Crosstalk: -60dB. Connectors: BNC (use #27-405 with RCA type video cables). Audio: Input/output:
High impedance, unbalanced. THD: <0.1%. Frequency response: 20Hz~20KHz, +/- 3dB. S/N ratio: >90dB.
Crosstalk: -90dB. Power: 120VAC, 60Hz.
Order #
33-7760
Audio/Video Selector
•Perfect for the
entertainment
center •Combines four
different video devices (VCR,
laser disc player, etc.) into one output •Compatible
with both mono and stereo devices •Four audio/video
inputs, one audio/ video output •20Hz~10MHz
frequency range •Isolation 30dB minimum
Remote Control Audio/Video Selector
With the most common audio and video inputs;
S-video, composite video, toslink digital audio
and line level audio, you can connect your DVD,
satellite receiver, VCR or game system to your
home entertainment system. The switcher has three
audio/video inputs and one audio/video output and
an ultra thin remote control.
(ea.)
$59.95
(2-4)
$58.50
Order #
32-4420
(ea.)
$19.95
(5-up)
$57.17
13
Add additional
components to
your TV and
home theater system by providing additional A/V
inputs to your system. Four A/V inputs including
composite video and Y/C (S–video). Mfr. #SVS-14.
Order #
80-3450
(ea.)
$31.95
Three-Way
Audio/Video
Switch Box
Tabletop control box
allows selection of
multiple A/V sources. Accommodates video and left
and right audio, all connections are all RCA type
female. Metal case has non-skid rubber feet and stays
securely in place. Dimensions: 6.9" (W) x 2.2" (H) x
3.9" (D). Sloped front, black color.
(1-5)
$19.95
(6-9)
$18.95
(10-up)
$15.09
Easily select from as
many as four separate
A/V inputs by remote
control. Ideal for
home theater systems
where the base band A/V signal is the desired source.
Specifications: Band width: 20Hz~10MHz. Gain:
1dB. Isolation: 50dB minimum. Inputs: Four sets via
RCA type connectors. Outputs: Two sets via RCA type
connectors. Power source: 120VAC, 300mA.
(ea.)
$53.95
(1-9)
$4.89
(10-up)
$4.49
Back
Remote Control
A/B Switch
Six-Way Video Selector
Tabletop video switcher provides independent
selection of up to six A/V sources, routing them to
two different destinations. Select from inputs such
as a satellite receiver, digital cable box, DVD player,
DVR, VCR or video game. Dual outputs, with
independent selectors, allow easy recording of one
source, while viewing another, or viewing of two
different sources on separate monitors. Inputs and
outputs are standard line level L/R audio, composite
video, and S-video. S-video connections are standard
four-pin DIN female, all others are RCA type female.
Rugged metal enclosure measures 13⁄4" (H) x 111⁄2" (W) x
51⁄4" (D), including non-skid rubber feet. Note: Either
composite or S-video inputs may be utilized, but not
both. This selector will not convert from one video
format to the other. Passive device requires no power.
Order #
50-7780
MSRP
$69.95
(1-3)
$40.95
•SB–V40S
accommodates four audio/video sources with a
choice of S–video or composite video connections
•Adds flexibility to existing systems Specifications:
•Inputs: Four A/V inputs with S–video (Y/C) jacks
and composite video phono jacks, L/R audio phono
jacks •Output 1: A/V output with S–video (Y/C) jack
and composite video phono jack, L/R audio phono
jacks •Output 2: Audio output with stereo mini jack
•Weight: 6.5 oz. (185g) •Dimensions: 71⁄8" x 13⁄4" x 23⁄8"
(179 x 43.9 x 60mm)
Order #
SB-V40S
(1-3)
$52.95
1-800-543-4330
Fax 1-800-765-6960
•Allows you to switch
between two 75ohm
inputs (cable, antenna,
satellite or dual cable
systems) •75ohm output
•AC adaptor: 120VAC/12VDC,
100mA included •5MHz~900MHz bandwidth •89dB
isolation •UL listed •Remote requires two “AA”
batteries (not included)
Order #
32-4425
32-4426
(4-up)
$49.95
Description
Switch
Replacement remote
(ea)
$29.95
8.39
(2-up)
$25.95
-
High Isolation Switches
•Three–way coaxial A/B/C
switch •Use for antenna, CATV
or VCR •Greater than 65dB
isolation through 550MHz
and 50dB through 900MHz
(4-up)
$37.95
Audio/Video
Selector
Remote Control
A/V Switch
216
(10-up)
$8.17
The AB–4 is a
push-button type
coaxial selector switch,
suitable for back–of–set
or similar flat surface
mounting. This unit offers
high isolation, great return loss
characteristics, and minimum loss
over the entire CATV spectrum, including both the
VHF and UHF bands. The AB–4 features an internal
secondary shield and a molded plastic outer cover,
providing excellent RF shielding. This durable
push–button type switch ensures reliable and
contact closure. The AB–4 is supplied with male
“F” connectors and necessary mounting hardware.
Electrical specifications: •Frequency range:
5~900MHz •Insertion loss: 0.2dB (5~250MHz), 0.5dB
(250~900MHz) •Isolation: 85dB (5~250MHz), 65dB
(250~900MHz) •Connectors: “F” type, female
Order #
33-2895
Audio/Video
Switcher
Order #
33-4140
(1-9)
$8.99
RF Switch
AV Switches
Order #
50-6195
Order #
33-390
(ea.)
$456.00
Back
Order #
33-7755
•Two input, 75ohm,
high isolation •A/B
switch for CATV,
MATV, MDS, SATV
and VCR applications
•Features zinc die–cast
housing •Molded PVC outer
case with mounting flanges
•5~900MHz bandwidth •90dB
isolation “off” •Patented design
Order #
33-1490
33-1485
Description
A/B/C
A/B
(1-9)
$13.69
5.29
(10-up)
$10.89
4.49
Coaxial Cable Switch
•Two input, slide type
A/B switch for CATV,
MATV, MDS, SATV, and
VCR applications •Offers
a quick selection from
regular TV antenna and
cable VCR or other input
sources •60dB isolation
typical •5~900MHz bandwidth •Output 75ohm
Order #
33-380
(1-9)
$4.49
(10-up)
$4.19
C53_pg_216-217
8/13/08
10:29 AM
Page 217
SATV/CATV
AV Splitters and Amplifiers
Back
section
13
HDMI Distribution Amplifiers
Split one HDMI source to distribute to multiple high-definition
displays. Ideal for retail displays, entertainment venues, and multiple residential
displays. Extends the range of HDMI compliant device by equalizing and boosting the
HDMI signal up to an additional 50'. Specifications: •Input/output: HDMI v1.2a+,
HDCP 1.0/1.1 •Video formats supported: VGA 1920 x 1200 and 1080p •Operating
frequency: Up to 165MHz •External power supply (included): 5VDC for 110V
Single Source HDMI Distribution Amplifiers
Splits, amplifies and extends a single HDMI source input (eg. digital cable box,
DVD player) to two or four HDMI HDTV displays (eg., HDTV, LCD projector),
simultaneously. Ideal for home theater, conferences, conventions, restaurants,
school and corporate training presentations. Use as an extender by placing at the
end of a long HDMI cable to regenerate the HDMI signal. Features: •Supports high
definition resolutions up to 1080p and UXGA •H.D.C.P. (High-Bandwidth Digital
Content Protection) compliant •HDMI v1.2 compliant •Total transmitting range:
100' (1080p); total length. Specifications: •Video amplifier bandwidth: 1.65Gbps
•Single link range: 1080p (1920 x 1200) •Vertical frequency range: 60Hz •Power
consumption: 10W, max •Input DDC signal: 5V p-p •HDMI output: 5VDC, 500mA.
Order #
33-10420
33-10421
Description
1-in x 2-out
1-in x 4-out
Dimensions (LxWxH)
4.72" x 2.62" x .79"
8.5" x 4.5" x 1.0"
Order # Description
33-10540 1 x 2
33-10542 1 x 4
33-10545 1 x 8
Dimensions
(L x W x H) with feet
MSRP
3.4" x 1.73" x .66"
$179.00
10.625" x 7.18" x 1.83"
249.00
17.323" x 7.893" x 1.748" 399.00
(1-4)
$99.95
149.00
249.00
(5-9)
$96.95
144.53
241.53
(10-24)
$91.95
137.08
232.20
(25-up)
$85.10
128.21
219.14
(ea.)
$156.00
209.00
Front
Component Video Distribution Amplifier
Allows a single component video input to be distributed to four HDTV displays, or each individual RCA
output can be used to distribute composite video to up to ten composite video displays (VCRs, analog TVs,
etc; ten composite video splitter) Features: •High bandwidth performance (240MHz) •Resolution support
up to 1080i •(Y/Pb/Pr, or RGB) RCA connectors Power: •15VDC; 300mA power adaptor included
Order #
33-10510
(ea.)
$59.95
Audio/Video
Distribution Amplifers
Order #
32-4430
32-4435
All-In-Two Multi-Room RF Distribution Kit
Description
Four-way
Six-way
(ea.)
$31.95
42.95
The All-In-Two Multi-Room RF distribution kit includes all of the components
needed to distribute broadband RF, 4 locally generated signals and IR remote control
to up to eight rooms in a house. The kits include: 4-channel RF modulator (5545),
3-input/8-output RF distribution panel (DA-550HHR or DA-550BID), three rooms of
IR interface, expandable to eight rooms (three 2100A and five 2501) and IR control
of four video devices (two 2172). •Limited quantities
Order #
5555BID
5555HHR
Description
Bi-directional amplifier
High head-room amplifier
(kit)
$502.12
502.12
A/V Distribution
Amplifier/Selector
#DA-550BID
Tabletop distribution amplifier allows
selection between two A/V inputs and provides
up to four outputs. Independent left and right
audio signal paths allow compatibility with
stereo sources including CD/DVD players, VCRs,
Back
video games and satellite receivers. Front panel
pushbutton selects between two input sources, and internal amplifier maintains
signal quality when distributed to four outputs. Gain at each output is 2dB over
input signal level. Rugged metal enclosure measures 15⁄8" (H) x 7" (W) x 27⁄8" (D),
including non–skid rubber feet. Color–coded input/output connections are RCA
type female. Requires 12VDC, AC adaptor included.
Order #
30-1376
MSRP
$49.95
(1-3)
$29.95
(4-up)
$26.95
#DA-550HHR
High Headroom Distribution Amplifier
The DA-550s can handle an extremely wide range of
input signals from both NTSC and digital HDTV. With outputs to eight televisions,
coax runs up to 150', three inputs, one from a CATV or antenna and two from
modulators, the DA-550 is the heart of a multi-room distribution system. The
DA-550BID offers a 5~42MHz return path for bi-directional communication for
use with cable modems and pay-per-view applications. The DA-550HHR is used
with high performance antenna applications for off air digital and NTSC signals.
Additional features: IR engine, remote power and expandable outputs.
Order #
DA-550BID
DA-550HHR
www.mcmelectronics.com
(ea.)
$167.00
167.00
NET 30
Terms
217
13
•Perfect for in–store display
demonstration walls or
karaoke display •One input
distributes four or six
amplified outputs •Video
and stereo sound input via
RCA jacks •Four or six
outputs, video and stereo
sound via RCA jacks
•Frequency range: •20Hz~10KHz •Isolation: 30dB minimum •Video input: 75ohm
•Audio input: 20Kohm •Operates from 15V/300mA adaptor •Adaptor included
C53_pg_218-219
section
13
8/13/08
10:30 AM
Page 218
SATV/CATV
A/V Distribution Amplifiers
#33-10255
#33-10256
High Performance Distribution Amps
These high performance distribution amplifiers
feature specifications such as a true one-to-one ratio, no signal
loss, low noise, low distortion and unity gain.
Order #
33-6875
33-6880
Mfr. #
AV400
AV700
Outputs
Four
Seven
(ea.)
$69.95
99.95
HDTV Audio/Video
Distribution Hub and Receiver
Component Video Distribution Amplifier
Four-way audio/component-video distribution
amplifier for Y, Cb, Cr and Y, Pr, Pb applications. Features high
performance, low distortion and true one-to-one signal ratio.
These professional grade amplifiers are cascadable for use in large
displays and are enclosed in metal housings to reduce interference.
Mfr. #AV400COMP.
Order #
33-7050
(ea.)
$119.00
Component Audio/Video
HDTV Distribution Amplifier
Distribute digital/HDTV and analog television signals
from a single A/V source to nine televisions/receivers, or use
one of the output ports to cascade additional distribution
amplifiers. Features: •Component video (Y, Pr, Pb) and
audio distribution •Compatible with all HDTV, digital
and analog signals •High performance, low distortion,
one-to-one signal ratio ensures equal picture quality
•Unlimited cascade capability •Mfr. #AV901COMP
Order #
33-10080
Distribute high definition component video and
digital or left or right audio over extended distances
using Cat 5e wire. Video and audio loop output to
accommodate future expansion to additional Cat 5e
transmitters and receivers. Supports 1080i video up
to 300' with Cat 6. Transmitter features: •Active
amplification ensures high-quality •Discrete passive
IR channel for external remote controls •Two RJ-45
outputs for additional location. Receiver features:
•Cable length equalizer for long distances •Video
continuity LEDs to ensure all signals are
transmitting •IR output
Order #
33-10255
33-10256
Mfr. #
Cat5TX
Cat5RX
Description
Transmitter
Receiver
(ea.)
$119.00
135.00
(ea.)
$169.00
Component Audio/Video HDTV
Distribution Amplifier with Digital Audio
13
Distribute digital and analog television signals, from
a single A/V source to nine televisions/receivers, or use
one port as a loop-thru output port to cascade additional
distribution amplifiers. Features: •Component video
(Y, Pr, Pb, or Y, Cr, Cb), composite video, analog audio
and SPDIF digital audio distribution •High bandwidth
(>50MHz) performance, low distortion, and one-to-one
signal ratio ensures equal picture quality. Power:
9~10VAC, 500mA adaptor included. Mfr. #AV901HD.
Order #
33-10090
TM
(ea.)
$249.00
Video Ground Loop Isolator
Ground loops in composite video systems can cause video distortions
such as herringbone and AC beat. Uniquely designed to eliminate ground
loop related distortions, this transformer features RCA female-to-female
connectors with a separate 9' RCA male-to-male pigtail cable that facilitates
multiple installation configurations and helps reduce cable connector strain.
Specifications: •Insertion loss: <0.5db •Frequency response: 0~3db @
10MHz •Input/output resistance: 75ohm •Built-in 600VDC transient
voltage surge suppression (12V RMS) •No power required (passive).
Order #
33-6927
MSRP
$59.95
Component Audio/Video HDTV
Distribution Amplifier with Digital Audio
Allows for multiple signal distribution equal to
source signal input. Distribute digital/HDTV and
analog television signals, including digital audio
and composite video from a single A/V source to
five televisions/receivers, or use one loop-thru output
port to cascade additional distribution amplifiers.
Features: •Component video (Y, Pr, Pb, or Y, Cr, Cb),
composite video and SPDIF digital audio distribution
•Compatible with all HDTV, digital and analog
signals •High bandwidth (>50MHz) performance, low
distortion, and one-to-one signal ratio ensures equal
picture quality Power: •9~10VAC, 500mA adaptor
included •Mfr. #AV501HDX
Order #
33-10087
(ea.)
$179.00
(1-3)
$31.95
Ground Isolation Transformer
5MHz~2.4GHz bandwidth for use in antenna, cable television and satellite
systems. Reduces the effects of ground loops such as herringbone, beat and
audio hum.
Order #
33-8700
(1-9)
$19.95
(10-up)
$16.95
Composite Video to S-Video Adaptor
This high quality adaptor converts composite video to S–video and S–video to composite
video. The adaptor measures only 13⁄4" long and 1⁄2" in diameter allowing it to plug directly
into the equipment and solves the problems associated with mixing composite and S–video
inputs and outputs.
Order #
33-0001
33-0002
33-0003
218
Description
S male to RCA female
S female to RCA female
S female to RCA male
(ea.)
$7.89
6.39
6.39
1-800-543-4330
Fax 1-800-765-6960
(2-up)
$7.59
6.19
6.19
S-Video Distribution Amplifier
Allows for multiple signal distribution
equal to the source signal input. Four way audio/video
distribution amplifier with S-video inputs and
outputs. Features high performance, low distortion
and true one-to-one signal ratio. These professional
grade amplifiers are cascadable for use in large
displays and are enclosed in metal housings to
reduce interference. Mfr. #AV400SV.
Order #
33-7045
(ea.)
$99.00
C53_pg_218-219
8/13/08
10:30 AM
Page 219
SATV/CATV
RF Modulators
section
13
Back
Digital RF Modulator
Agile Modulators
The consumer agile modulators are unique RF, UHF
and VHF hyperband modulators. Their design allows
the user to insert video from a VCR, laser disc or any
baseband video signal into their home RF system. The
#33-2025 and 33-2035 work on UHF. The #33-2020
and 33-2030 work on VHF hyperband or with CATV
systems. The single and dual channel units add
flexibility to your system. Perfect for whole house
TV systems and CCTV systems.
Order #
33-2020
33-2025
33-2030
33-2035
Description
VHF hyperband single output
UHF single output
VHF hyperband dual output
UHF dual output
(ea.)
$159.00
159.00
219.00
219.00
RF Modulator
•Hook any DVD
player, VCR, video
game, satellite, or
other composite source
to a television with a coax
connection •RF and composite in •RF coax out
on channel 3 or 4 •Automatically switches when
composite source is switched on
Order #
PH61159
(1-9)
$12.95
(10-49)
$12.69
(50-99)
$12.43
(100-up)
$11.98
Accepts video and audio from a camera, VCR
or any other video device. Digital channel selection
for UHF channels 14~69 or CATV channels 66~134.
Antenna/CATV input and built-in combiner.
•Frequency range: 471.25MHz ~ 855.25MHz
•Antenna input frequency: 50MHz~900MHz
•Automatic gain control
Order #
82-8105
(ea.)
$84.95
Digital UHF
Modulator
Back
The USM-8D
is a low cost,
frequency stable,
UHF modulator
developed for
use in adding
satellite, VCR, or
security video channels to an existing home
distribution system. The frequency adjustable feature
allows multiple channel use at an extremely low cost.
Specifications: •Frequency range: UHF channels
14~69 and CATV channels 65~139 •Video input:
Composite •Output impedance: 75ohm •Output
level: 7dBmV •Power input: 115VAC, 60Hz, 5W
•Connectors: “F” for RF, RCA video and audio
•Mfr. #USM-8D
(1-9)
$48.95
The 5515, 5525-01 and 5545-01 are one, two and four
channel input modulators with loop–out capabilities
and integrated IR control. Each offers IR emitter
output jacks and the ability to remotely power a
DA-550 series or an DA-8200 series distribution panel
from up to 75' away. The 5500 series works with both
the 12 volt and 5 volt IR systems and accessories. The
5515, 5525-01 and 5545-01 offer 75ohm termination
jumpers on all channels to loop–through the video and
audio signals. Features include: 1, 2 and 4 channels,
push button programming, UHF 14~64 and CATV
65~125, 25dBmV output.
Order #
5515
5525-01
5545-01
(ea.)
$72.00
124.00
197.00
Back
(10-up)
$45.95
MINI RF Modulator
RF Modulator and Video Switcher
The Terk MINI modulator
is a compact, inexpensive
modulator that will convert
any video source to VHF for
viewing on your TV on either
channel 3 or 4. Its low signal
loss enables it to deliver
excellent picture and sound
quality. The MINI reduces
the clutter around your TV by
easily mounting on your wall
or entertainment center. The MINI was designed
to be in-line, so that it can hang or be mounted
on a vertical surface and out-of-sight. After first
installation, there is no need to access the MINI
again. It features automatic signal detection and
automatically switches between A/V sources when
a signal is detected.
Order #
33-9645
Outputs
1
2
4
13
Order #
33-2740
Digital RF
Modulators
Mfr. #
MINI
(ea.)
$17.95
Digitally Tuned Modulators
The Theater 1001F is a digitally tuned modulator
that distributes high quality audio/video signal to
multi-room locations. The digital phase lock loop
(PLL) tuning eliminates channel drift. 120
selectable channels: UHF channels 14~69; cable
channels 60~94, 100~125. Binary Code Decimal
(BCD) channel selector for easy tuning. Isolated
right and left mono inputs improve audio
performance. Features: Switch type channel
select and full channel memory for power outages.
Order #
33-7255
Mfr. #
1001F
Channels
Single
•Lets you connect components with S-video or
composite output (DVD, satellite) to a TV without
A/V jacks, by modulating the signal to RF •Ideal for
hooking up several components to a TV •Combines
RF modulator and S-video switcher into one unit
•Converts any input (S-video, composite, A/V, stereo)
to RF output •A/V and S-video switching •Composite
to S-video convertor •Front input, stereo input •Gold
plated connectors
Order #
CRF940
(ea.)
$25.95
Back
(ea.)
$59.99
Channel Combiners
RF Modulator w/Antenna Switch
Accepts video and audio from a camera, VCR or any
other video device and modulates to television channel
3 or 4. Built-in selector switch to choose between A/V
source and antenna or cable TV.
Order #
82-8100
(ea.)
$25.45
TM
•Combines channel
3/4 signal (from VCR,
computer, game, etc.)
with existing VHF signals
not including channel 3/4
•Also removes bleedover
of channel 3/4 modulated
signal from adjacent
channels 2 and 4
Order #
33-255
33-1080
Combiner
3
4
(1-9)
$14.95
14.95
(10-up)
$13.89
13.89
www.mcmelectronics.com
SLV A/V RF Modulator
The mini RF modulator is a compact, inexpensive
modulator that will convert any composite video
source to VHF for viewing on your TV on either
channel 3 or 4. Its low signal loss enables it to deliver
excellent picture and sound quality. This modulator
allows you to connect additional A/V components, such
as a DVD player or a gaming system, to your TV when
there are no available RCA jacks. Inputs: Three RCA
(composite video and stereo audio), one “F”.
Order #
33-9775
NET 30
Terms
MSRP
$19.99
(1-5)
$12.95
(6-up)
$12.69
219
C53_pg_220-221
section
13
8/13/08
10:31 AM
Page 220
SATV/CATV
RF Amplification and Distribution
#33-2845
#33-2840
Broadband
Amplifiers
13
The BIDA Series are
professional quality,
broadband, two-way
capable, indoor
hybrid distribution
amplifiers that
are designed for
RF distribution
systems. Ideal for
multi-channel RF
distribution systems
whose input source
is a “cable drop”
or the output of a
MATV/SMATV/CATV
headend. May
be used as the
launch amplifier in a
distribution network.
These amplifiers use dual push–pull hybrid modules,
capable of delivering high output levels with low
distortion, even in systems with over 100 channels of
programming. Power doubling models can be cascaded
together with lower distortion resulting than the
push–pull amplifiers allowing the system to maintain
higher signal integrity. The gain and slope controls
are designed between the hybrid modules for optimum
noise figure, input return loss and output capability.
Test ports for both the input and output are provided
for testing signal levels without interrupting service.
The BIDA Series come in a rugged, aluminum chassis
that provides exceptional heat dissipation.
Order #
33-7815
33-7820
33-7850
33-7855
Bandwidth
MHz
Gain dB
49~550
50
49~750
32
49~860
44
49~860
44
Multiple
Dwelling Amplifier
This professional quality, broadband, indoor hybrid
distribution amplifier is designed for RF distribution
systems. Ideal for those RF distribution systems
whose input source is a cable drop, the output of
a MATV/SMATV headend, or the output of a small
CATV headend. The ACA 30-550 amplifier has a flat
30dB of operational gain, which is variable using a
built-in gain control. Variable slope control is also
provided, with an available range of 9dB. This
amplifier uses a push-pull technology, capable of
delivering high output levels with low distortion, even
in systems with 110 channels of programming. It is
housed in a compact, aluminum chassis that provides
excellent heat dissipation. The ACA 30-550 is provided
with an external power transformer. The unit can also
be powered directly with 24VAC. Specifications: RF:
•Frequency range: 47~550MHz •Gain: 32dB •Noise
figure(a): 8.0dB •Output level: +44dBmV •Gain
control range: 15dB •Slope control range: 10dB
•Impedance all ports: 75ohm •Mfr. #ACA 30-550
Order #
33-2875
(ea.)
$276.00
Broadband
Distribution Amplifiers
The ZCM Series includes professional quality,
broadband distribution amplifiers, designed for
special purpose applications in the MATV, SMATV,
private and wireless cable markets. These amplifiers
cover the 50~550MHz frequency range and provide
low noise amplification at a reasonable cost. Two
models are available with either 10 or 20dB of gain,
each capable of accepting a relatively high input
level. Specifications: ZCM-101 RF: •Frequency
range: 50~550MHz •Gain: 10dB •Noise figure:
3.5dB •Impedance-all ports: 75ohm General power
requirements: •Voltage: 117VAC, ±10% •Frequency:
60Hz •Power: 1.2W •Connectors (top panel): •RF
input: Type “F”, female RF output: Type “F”, female
ZCM-201 RF: •Frequency range: 50~550MHz •Gain:
20dB •Noise figure: 3.5dB •Impedance all ports:
75ohm General power requirements: •Voltage:
117VAC, ±10% •Frequency: 60Hz •Power: 1.4W
•Controls (top panel): Tilt: Var. Control •Connectors
(top panel): RF Input: Type “F”, female •RF output:
type “F”, female
Order #
33-2840
33-2845
B
(1-9)
$14.95
23.95
15dB RF Amplifier
C
(1-9)
$16.95
(10-up)
$16.43
RF Amplifiers
Low noise VHF/UHF/FM signal amplifiers. Variable gain control
–10dB. Built–in FM trap (-20dB). Specifications: Frequency
range: 40~862MHz. Noise figure: <7dB. Power: 120VAC.
Fig.
A
B
C
A
B
C
Order #
33-8715
33-8720
33-8725
Outputs
1
2
4
Gain
30dB
25dB
20dB
(1-9)
$17.50
14.69
17.95
(10-up)
$16.49
14.19
16.95
RF Amplifiers
VHF/UHF/FM signal amplifiers for residential cable and
antenna television. 40~862MHz bandwidth. <6dB noise figure.
Operates on 120VAC.
Fig.
A
B
C
Order #
33-8730
33-8735
33-8740
Outputs
1
2
4
Gain
10dB
10dB
5dB
(1-9)
$11.95
14.99
13.49
UHF/VHF/FM
12dB Amplifier
Features: •Low
noise •Lightning
protection •AC power indicator •Two outputs •Low
cost Specifications: •Bandwidth: 54~890MHz
•Gain: VHF, 12dB; UHF, 11dB •Maximum input:
VHF, 35dB; UHF, 25dB •Maximum output: VHF,
47dB; UHF, 38dB •Noise figure: VHF, 6dB; UHF,
7dB •Power requirements: 115VAC; 60Hz
•Dimensions: 57⁄8" (W) x 15⁄8" (H) x 3" (D)
Order #
33-0445
(1-9)
$36.31
UHF/VHF/FM
36dB Amplifier
The CA-30 is a high quality push-pull amplifier producing signals with extremely
low distortion and harmonic content. The CA-30 enclosure uses a black anodized
aluminum extrusion to assure reliable heat sinking and corrosion resistance.
Features: •Wide frequency range: 54MHz~550MHz, 30dB gain, adjustable slope
control, adjustable gain control, input and output test points, designed for CATV
apartment distribution systems Specifications: •Bandwidth: 54~550MHz •Gain:
30dB •Gain adjust range: 0~8dB •Power requirements: 115VAC, 60Hz, 4W •Slope:
0~8dB variable •Noise figure: CA-30, 5.0dB
Order #
33-2670
(1-9)
$156.00
1-800-543-4330
Fax 1-800-765-6960
(10-up)
$23.67
(10-up)
$9.76
12.42
12.59
Push-Pull Amplifiers
220
(10-up)
$14.68
22.95
Specifications: RF: •Frequency range: 54~220MHz, 470~900MHz •Input level
min: -7.0dB •Input level-max: +18dB •Gain: 16dB (50~22), 12dB (470~800), 10dB
(800~900) •Noise figure: 3.0dB (VHF), 4.0dB (UHF) •Output level max: +44dBmV
•Impedance all ports: 75ohm General: •Power requirements: •Voltage: 117VAC,
±10% •Frequency: 60Hz •Power: 4.2W •Mfr. #ZTA-15
Description
(ea.)
Push–pull
$576.00
Push–pull
607.00
Push–pull
699.00
Power doubling 771.00
Order #
33-2850
A
Mfr. #
ZCM-101
ZCM-201
(10-up)
$151.00
Features:
•Low noise •Two switchable FM traps •Separate
gain controls •AC power indicator •50dB output
capability •-20dB monitor output •Fuse protected
Specifications: •Bandwidth: 54MHz~108MHz,
174MHz~216MHz, 470MHz~812MHz •Gain: VHF,
31dB; UHF, 36dB •75ohm input/output •Power
requirements: 115VAC; 60Hz •Dimensions: 83⁄4" (L) x
17⁄8" (H) x 33⁄4" (D) •Fuse protected
Order #
33-0890
(1-9)
$105.00
(10-up)
$102.00
C53_pg_220-221
8/13/08
10:32 AM
Page 221
SATV/CATV
RF Amplification and Distribution
section
13
DA-520A
The DA-520A is a bi–directional
amplifier providing 20dB of forward gain and
0dB reverse gain. Specifications: Bandwidth:
54~806MHz. Gain: 20dB +/- 1dB.
Order #
DA-520A
(ea.)
$67.99
RF Distribution
Amplifier
Distribution Panel
Creates an ideal entry level product
for broadband distribution. Has one
input for CATV or off–air antenna and six outputs.
Four outputs are for up to 75' and two are for
150'. Has bi–directional capabilities allowing for
compatibility with cable modem and interactive
set–top boxes. Specifications: Bandwidth
54~806MHz. Gain: 20dB +/- 1dB.
Order #
DA-506BID
(ea.)
$71.95
For systems with up to eight TV outlets and cable
lengths up to 150'. The DA-8200 series provides
outputs to eight televisions, three inputs from an
off–air antenna or CATV and two modulator locations.
May be remotely powered from up to 75' away by
using a remote wall plate model 2010 or any 5500
series or SVM series modulator.
Order #
DA-8200BID
DA-8200HHR
Description
Bi–directional amplifier
High head–room amplifier
(ea.)
$167.00
167.00
Broadband Structured Wire RF Amplifiers
Compatible with the market leader of structured wiring panels, these
5~1000MHz, DOCSIS® compliant amplifier modules are the ideal drop-in
replacement for CATV in-home signal distribution. Improve your multimedia
application with the latest broadband technology for HDTV QAM signals.
Features include a durable, salt-spray-resistant housing, weather-sealed
“F” ports, and exceptional surge performance.
Order #
33-10225
33-10226
Description
6 output
8 output
Gain
+6.5dB gain
+10.0dB gain
(ea.)
$84.95
94.95
(1-9)
$156.00
(10-up)
$151.00
Multi–Set Indoor
Distribution
Amplifiers
10dB Micro Amplifier
Models #3043
and 3044 allows
distribution of amplified signals to 2, 4 or 8 television
sets or other video equipment without the use of
additional splitters.
(10-up)
$14.99
Order #
33-8975
33-8980
Bi-Directional CATV Amplifiers
Mfr. #
3043
3044
Description
2 output
4 output
Gain
22dB
22dB
(ea.)
$32.95
34.95
Digital amplifiers with return path for use with CATV convertors (pay per view) and
cable modems. Soldered back ensures isolation and signal integrity. Specifications:
Bandwidth: 54~1000MHz. Noise figure: 3.5dB. Power: 12VDC, 250mA via included
adaptor (using “F” cable).
Order #
33-7110
33-7111
33-7115
33-7116
Forward Gain
15dB
15dB
15dB
20dB
Reverse Gain
0dB (Flat)
10dB
15dB
15dB
(1-9)
$47.95
47.95
63.95
59.95
(10-up)
$43.95
42.95
58.95
54.95
#33-8760
#33-8745
UHF/VHF/FM 25dB Amplifier
Broadband Distribution Amps
Features: •Low noise •Lightning protection •AC power indicator •Switchable
FM trap •Low cost Specifications: •Bandwidth: 54~900MHz •Gain: VHF, 25dB;
UHF, 22dB •Maximum input: VHF, 18dB; UHF, 16dB •Maximum output: 40dB
(54~800MHz) •Noise figure: VHF, 5dB; UHF, 7dB •75ohm input/output •Power
requirements: 115VAC; 60Hz •Dimensions: 57⁄8" (W) x 15⁄8" (H) x 3" (D)
Suitable for medium sized distribution networks
including homes and small condominium complexes.
High gain low noise amplifier with built–in FM trap.
Specifications: Frequency range 40~1000MHz.
FM trap -20dB. Power: 120VAC.
Order #
33-0450
(1-9)
$29.99
(10-up)
$28.32
VHF/FM 20dB Amplifier
UHF/VHF/FM 25dB
Features: •Low noise
•High overload capacity
•Lightning protection
at RF input •Heavy
gauge metal case •On-off
indicator light •Switchable FM trap Specifications:
•Bandwidth (MHz): VHF 54~300; UHF 470~890
•Gain: VHF, 25dB; UHF, 23dB •Maximum input
(dBmV): •VHF, 15; UHF, 17 •Maximum output
(dBmV): VHF, 40; UHF, 40 •Noise figure (dB): VHF,
low 5.4, high, 6.2; UHF, 14 •Power requirements:
117VAC •Dimensions: 65⁄8" (W) x 17⁄16" (H) x 33⁄32" (D)
Order #
33-290
Order # Outputs
33-8745
1
33-8755
2
33-8760
4
(1-9)
$26.95
(10-up)
$25.95
•50~450MHz bandwidth •20dB gain
•40dB output capability •117VAC
power requirement •Dimensions:
31⁄2" (W) x 21⁄4" (H) x 11⁄2" (D)
Order #
33-270
(1-9)
$20.95
(10-up)
$20.07
Four-Way Amplified Coupler
•50MHz~550MHz bandwidth •1~3dB
gain •117VAC power required •One
input, four outputs •Dimensions: 31⁄2"
(W) x 21⁄4" (H) x 11⁄2" (D)
Order #
33-1475
(1-9)
$13.19
Gain
36dB
15dB
11dB
Gain Adjust
(1-9) (10-up)
18dB
$31.95 $28.95
10dB
27.95 26.95
29.95 28.68
Two-Way
Amplified Coupler
•50MHz~550MHz bandwidth
•4~6dB gain •117VAC power
required •One input, two
outputs •Dimensions: 31⁄2" (W) x 21⁄4" (H) x 11⁄2" (D)
Order #
33-1460
(1-9)
$14.69
(10-up)
$13.09
(10-up)
$12.49
www.mcmelectronics.com
NET 30
Terms
221
13
(1-9)
$19.95
The HDA-1000 is a low noise linear distribution
amplifier providing high power outputs at extremely
low distortion. The wide bandwidth allows the user
a single amplifier for all distribution frequency
applications; VHF, mid band, super band, hyper
band, ultra band and UHF. Features: •Wide forward
frequency range: 50MHz~1GHz, low noise figure,
30dB gain to 1GHz, surface mount strip line design,
designed for all broadband systems, built-in slope
(44dB typical, 55MHz~1GHz) Specifications:
•Bandwidth: 50MHz~1GHz •Forward gain:
50MHz~600MHz, 31dB, ± 2dB, 600MHz~1GHz,
32dB, ± 3dB •Power requirements: 115VAC, 60Hz
Order #
33-2675
10dB micro amplifier with 45~1000MHz bandwidth. Soldered back ensures
130dB RFI shielding. Heavy-duty tin plated zinc housing. Specifications:
Noise figure: 7dB. Power: 12VDC, 100mA. via included adaptor (using “F” cable).
Order #
33-7125
50MHz~1GHz
Broadband Amplifier
C53_pg_222-223
section
13
8/13/08
10:33 AM
Page 222
SATV/CATV
VideoEase™ HDTV Component Video/Digital Audio Balun
The component video/audio balun allows one component video (YPbPr or RGB)
signal and one audio signal to be transmitted via cost-effective unshielded twisted
pair (UTP) cable in a point-to-point configuration. Used in pairs, the component
digital balun supports 480i/p, 720p and 1080i/p video formats for hi-definition
(HDTV) video applications. Features: •Supports 480i/p up to 1000' (305m) and
720p/1080i/p up to 500' (152m) via Cat 5 UTP, respectively •Available with colorcoded RCA cable connectors •Supports either digital audio (5000050, or 500051),
or analog audio (500052, or 500053) on fourth twisted pair •Modular shielded
RJ-45 connector •Used in pairs, sold separately
Order #
33-10060
33-10061
33-10062
33-10063
#33-9585
#33-9590
The VideoEase S-Video Balun allows a single S-video
signal to be transmitted via unshielded twisted pair
(UTP) cable up to 1000' (305m) in a point-to-point
connection. The product is available in two models;
the S-Video Balun (500016) and the S-Video/Audio
Balun (500017). Used in pairs, the S-Video Balun
eliminates costly and bulky S-video cable, allowing
S-video equipment to be connected or moved to any
convenient modular outlet. The S-Video Balun also
works in conjunction with MuxLab’s Audio-Video
Distribution Hub (500200) to allow S-video
programming to be distributed via UTP. Some of
the applications are; classroom video distribution,
commercial and home audio/video systems, hospital
video training, video conferencing, and video kiosks.
Note: Baluns must be used in pairs and are sold
individually. •Sold individually
Mfr. #
500016
500017
Description
S-Video
S-Video and Audio
Connectors
Male RCA
Female RCA
Male RCA
Female RCA
Audio
Digital
Digital
Analog
Analog
(ea.)
$104.00
104.00
104.00
104.00
VideoEase™ Component Video Balun
S-Video Baluns
Order #
33-9585
33-9590
Mfr. #
500050
500051
500052
500053
The VideoEase™ Component Video Balun allows a single component video signal
(Y, Pb, or Pr) to be transmitted via cost-effective unshielded twisted pair (UTP) cable.
Three balun pairs are required for one complete component (YPbPr) video connection. The
product allows three coaxial cables to be replaced by one Cat 5 twisted pair cable, allowing
standard structured cabling techniques to be used for neater and more streamlined cabling. The
component video balun is compact enough to allow three units to be connected side by side on the back of
the component video equipment. Features and benefits: •Supports one component of the YPbPr video signal
•Three balun pairs required per YPbPr connection •Up to 1,000' (305m) via Cat 5 UTP •Gold-plated connector
•Cable strain relief •Compact design •Lifetime warranty •Design patent pending
Order #
33-9755
Mfr. #
500021
(ea.)
$37.95
Videoease PS/2 Convertor Balun
•Allows PS/2 devices to be located up to 350' away from the PC •Using
inexpensive 4-pair Cat 5 shielded twisted pair or unshielded twisted pair
cable depending on the equipment used •Used in pairs, #33-10105 balun
eliminates the need for a local keyboard and mouse •Typical applications
include corporate projection systems, classroom video instruction and video
information systems
(ea.)
$37.95
84.95
Order #
33-10105
Description
PS/2 remote PS/2 side
Mfr. #
500045
(ea.)
$35.00
13
VideoEase™ Audio Balun
VideoEase™ Composite
Video/Stereo Balun
The VideoEase™ stereo/video balun allows a
single composite video signal and stereo audio
signal to be transmitted via UTP cable up to 2,200'
in a point-to-point connection. Features: •Full audio
bandwidth response for high fidelity applications
•20Hz~20KHz audio bandwidth •Built-in color-coded
cable leads for ease of installation. Used in pairs,
sold individually.
Order #
33-9626
Mfr. #
500039
(ea.)
$72.95
Dual Audio/Video Balun
The VideoEase Dual
Audio/Video Balun
allows up to two
composite video
signals and up to
two unbalanced audio
signals to be transmitted
via unshielded twisted pair (UTP)
cable in a point-to-point connection. The
Dual Audio/Video Balun eliminates up to four
coaxial cables, allowing audio/video equipment to be
connected via space-efficient and cost-effective Cat 5
twisted pair cable. The Dual Audio/Video Balun also
works in conjunction with MuxLab’s Audio/Video
Distribution Hub (500200) allowing audio/video
programming to be distributed via UTP to up to eight
locations. Features: Up to 2200' (670m) in color via
Cat 5 UTP. Pair required for use, sold individually.
Order #
33-9610
222
Mfr. #
500012
(ea.)
$87.95
The VideoEase™ Audio Balun allows any unbalanced analog audio signal to
be transmitted via a single unshielded twisted pair (UTP) cable for more versatile
cabling. Used in pairs, the audio balun eliminates costly and bulky coax cable, allowing
consumer and commercial audio equipment to be connected using standard premises wiring
techniques. One or two pair of baluns are required depending on whether the application is for
monaural or stereo audio. The audio balun features screw terminals and built-in cable strain relief for ease of
installation and reliable connectivity. Applications include auditoriums, arenas, schools, home theater systems,
airports, hotels, hospitals, conference rooms. Features and benefits: •Eliminates coax cable •Up to 5,000'
(1.5km) via Cat 5 UTP •20~20KHz bandwidth •Gold-plated RCA connector •Cable strain relief •Compact
design •Lifetime warranty •Design patent pending
Order #
33-9745
Mfr. #
500019
(ea.)
$37.95
RGB Baluns
The VideoEase RGB Balun allows a single red/green/blue component video
signal to be transmitted via unshielded twisted pair (UTP) cable in a point–
to–point connection. The RGB balun eliminates three coaxial cables, allowing
RGB audio/video equipment to be connected via space–efficient and cost–effective
Cat 5 twisted pair cable. The RGB balun works with RGB equipment that carries
the synchronisation pulses on one of the three color signals (ie; sync on green). The
RGB balun works with LCD projectors, monitors, plasma screens, matrix switchers, splitters,
convertors and RGB video equipment and comes with three separate coaxial jumpers for ease of installation.
Features: Up to 2200' (670m) in color via Cat 5 UTP. Pair required for use, sold individually.
Order #
33-9595
(ea.)
$114.00
Stereo A/V Balun
The VideoEase Stereo Audio/Video Balun allows a single composite video signal
and a maximum of two unbalanced audio signals to be transmitted via unshielded
twisted pair (UTP) cable in a point–to–point connection. The Stereo Audio/Video
Balun eliminates up to three coaxial cables, allowing audio/video equipment to
be connected via space–efficient and cost–effective Cat 5 twisted pair cable. The
Stereo Audio/Video Balun also works in conjunction with MuxLab’s Audio/Video
Distribution Hub (500200) allowing audio/video programming to be distributed via UTP.
Features: Up to 2200' (670m) in color via Cat 5 UTP. Pair required for use, sold individually.
Order #
33-9625
1-800-543-4330
Fax 1-800-765-6960
Mfr. #
500001
(ea.)
$87.95
C53_pg_222-223
8/13/08
10:34 AM
Page 223
SATV/CATV
Videoease™ Quad Audio Balun
The quad audio balun allows up to four analog line audio signals to be transmitted
via unshielded twisted pair cable in a point-to-point connection. One pair of quad
audio baluns can replace four coax audio cables with one Cat 5 cable. Features:
•Unbalanced, line-level analog audio up to 5,000' via Cat 5 cable •Less than 1dB
per pair over frequency range. Used in pairs, sold individually.
Order #
33-10115
Mfr. #
500033
section
13
(ea.)
$87.95
Videoease Quad Video Balun
•Developed for the security video and audio-video markets, the
quad video balun allows up to four composite video channels
to be transmitted over one Cat 5 cable, thus replacing up to
four coaxial cables for more cost-efficient cabling •Supporting
composite video up to 2,200' (670m) via Cat 5 cable and works
in pairs •Streamlining cabling in applications such as security
video, video-conferencing, classroom instruction, tradeshow
demos, PC-training, airline information systems and home
entertainment systems •Used in pairs, sold individually
Order #
33-10110
Description
Quad VGA balun
Mfr. #
500032
VideoEase™ VGA
Balun II Over UTP
Supporting distances up to 350', the VideoEase™
VGA Balun II is a passive device that fully supports
VGA and SVGA (RGBHV) transmission via one Cat 5
UTP cable without the need for shielded twisted pair
(STP) cable. This breakthrough technology allows
VGA equipment to be deployed more easily in both
new and pre-wire structured cabling environments.
Used in pairs, sold individually.
(ea.)
$87.95
VideoEase™ MonoPro™ XLR
The MonoPro™ XLR connectors allow a standard AES analog or digital audio
channel to be connected via Cat 5 unshielded twisted pair cable (UTP) in the
professional audio environment. The product features rugged cable strain relief
and comes with locking XLR3 connectors for added cabling versatility. Features:
•Rugged cable strain relief •Line analog audio up to 5,000' (1.5km) via Cat 5
•Digital audio up to 1,400' (426m) via Cat 5 •Wires terminate inside product
•Locking XLR3 connector •Optional wire terminal for ground/shield (if required)
•Up to 5,000' and 1,400' via Cat 5 for analog or digital audio, respectively.
Order #
33-10050
33-10055
Mfr. #
500025
500026
Description
MonoPro™ XLR male
MonoPro™ XLR female
Order #
33-9601
33-9602
33-9603
#33-10055
Description
PC side (HD15-male)
Monitor side (HD15-female)
Monitor side (HD15-male)
Mfr. #
(ea.)
500040 $105.00
500041 105.00
500042 105.00
(ea.)
$35.00
35.00
Videoease Active VGA Balun Kit
Order #
33-10120
Mfr. #
500035
(kit)
$359.00
VideoEase™ CCTV Pass-Thru Balun
The VideoEase™ CCTV Pass-Thru Balun allows video, two-wire PTZ control,
and remote power to be transmitted via one 4-pair Cat 5 cable, thus eliminating
the need to install multiple cables for more efficient cabling in the CCTV security
and surveillance environment. The pass-thru balun may be used in pairs, or in
conjunction with standard twisted pair cross-connect devices and other MuxLab
CCTV baluns such as the 500000, 500009, 500023 and 500015. Features: •Combines
video, PTZ control and remote power under one 4-pair Cat 5 cable for more efficient cabling
•Video up to 2,200' (670m) via Cat 5 UTP •Remote power up to 350' (106m) @ 24VAC/5VA via two twisted pairs
Order #
33-10065
Mfr. #
500022
(ea.)
$39.00
Order #
33-9615
CATV Balun
The VideoEase CATV Balun allows traditional 75ohm coaxial cable to be
replaced by a single pair of Cat 5 UTP cable in the CATV, VHF and FM
environments in certain applications. The CATV Balun allows broadband
CATV equipment to be integrated into structured cabling systems thereby
allowing CATV equipment to be moved or added to any convenient modular
wall outlet. The VideoEase CATV Balun provides a versatile cabling solution for broadband video systems
used by schools, government, corporations, hospitals, financial institutions, hotels and convention centers. The
CATV balun works in conjunction with CATV splitters, amplifiers and cable modems for a total cabling solution.
Features: Low return loss eliminates “ghosting”. Pair required for use, sold individually.
Order #
33-9630
Mfr. #
500302
(ea.)
$63.95
16 Port Rackmount Balun Chassis
The rackmount balun chassis is designed as a head-end cable
management solution to allow any combination of MuxLab
square baluns to be installed in a 19" relay rack. Features:
•Supports up to 16 baluns •Baluns install forward rear-facing
•Space efficient, 2U height •Latching mechanism for secure installation •Snap-in design for ease of installation
•Includes four rackmount screws and washers •Slot number silkscreen on front and rear •Mfr. #500900
Order #
33-9620
Audio/Video Hub
The VideoEase Audio-Video Hub allows up to two
baseband composite or one S-video signal and up
to two audio signals to be distributed to up to eight
destinations via twisted pair (UTP) cable for more
cost-effective and versatile cabling. The Audio-Video
Hub when used in conjunction with MuxLab’s line
of VideoEase baluns, allows coaxial cable to be
eliminated between the audio-video source and
the destinations. The product works with the
CCTV Baluns (500000, 500009), Stereo Audio-Video
Balun (500001), Dual Audio-Video Balun (500012)
and S-Video Baluns (500016, 500017). A looping
output allows the source input to be distributed
to other baseband audio/video equipment including
matrix switchers, multiplexers, VCRs and monitors.
Applications include: Classroom audio/video
instruction, corporate audio/video presentations,
tradeshow demonstration systems, CCTV security
and surveillance. Features: Up to 2200' in color via
Cat 5 twisted pair cable. 2-year warranty.
(ea.)
$259.00
www.mcmelectronics.com
Mfr. #
500200
(ea.)
$649.00
16 Port Passive CCTV Hub
The passive 16 port CCTV hub allows video, remote
power and PTZ control to be transmitted via one Cat 5
cable, thus eliminating the need to install multiple
cables for more efficient cabling in the security video
environment. The model 500130 features female BNC
connections for coax video output, and the 500131 has
female RJ-45 connectors for twisted pair video output.
Features: Space efficient 1U height •Supports up
to 16 inputs •Port switch to set power-thru, or
pass-thru •Pin configuration table on unit •Works
in conjunction with 500000, 500009, 500015, 500022,
500023, 500024, 500029 and 500120 baluns.
Order #
33-10125
33-10130
NET 30
Terms
Mfr. #
500130
500131
(ea.)
$260.00
260.00
223
13
•Extends the distance between the computer system unit and
a remote display monitor by up to 480' •It accomplishes this
by means of a local transmitting unit, and remote receiving
unit, connected by standard Cat 5 twisted pair ethernet cable
Features: •Uses Cat 5 ethernet cable: For economy; easy installation; and utmost data transfer reliability
•High resolution video: Up to 1800 x 1440 at 100 meters •Supports VGA and SVGA monitors •Long distance
transmission, up to 160m (480') •Local unit includes port for local monitor
C53_pg_224-225
section
13
8/13/08
10:34 AM
Page 224
SATV/CATV
Audio/Video to Category 5 Balun System
Take advantage of Cat 5 (or higher) cable for interconnecting A/V components over long distances. Common signal formats
such as composite video, RGB component video, S–video and line level audio can easily be sent over UTP cable distances from
400'~1000' depending on model. In retrofit applications, utilize existing unused pairs of Cat 5 data cable already in place. In new
construction, take advantage of the smaller size and lower cost of Cat 5 cable when distributing signals throughout the structure.
Housed in compact ABS enclosures, each balun accepts standard RJ-45 male connectors. Completely passive design, these units
require no power. Each unit is clearly labeled to identify which RJ-45 connector pair is used for the designated signal path.
Sold individually, all baluns must be used in pairs.
Back
Back
Component Video Balun
Use to send Y/Pb/Pr component video signals over
Cat 5 cable. This balun features three gold plated
male RCA connectors on the end of 8" pigtails color
coded red, green and blue. Additionally, a female
orange RCA connector provides path for digital audio
(SPDIF). Included is a hook and loop tape set which
allows direct attachment to the rear of plasma and
other monitors. Cat 5 connection is a single female
RJ-45 jack. Utilizes four pairs: •Red: Pin 7/8
•Green: Pin 3/6 •Blue: Pin 1/2 •SPDF: Pin 4/5
Specifications: •Distance: 400' max (Cat 5)
•Dimensions: 1.0" (H) x 3.2" (W) x 2.4" (L)
Order #
50-7722
MSRP
$109.00
(1-3)
$63.95
(4-up)
$52.95
L/R Audio/Video Balun
Use to send composite video, plus two channels of
unbalanced line level audio over Cat 5 cable. This
balun features three 8" pigtails with gold plated male
RCA connectors, color coded red, white and yellow,
and a single female RJ-45 jack. Utilizes three Cat 5
cable pairs: •Red: Pin 1/2 •White: Pin 3/6 •Yellow:
Pin 7/8 Specifications: •Video bandwidth:
50Hz~8MHz •Audio bandwidth: 10Hz~50KHz
•Distance: 1000' max (Cat 5) •Dimensions (excluding
connectors): 1.0" (H) x 2.36" (W) x 3.22" (L)
Order #
50-7732
MSRP
$79.95
(1-3)
$46.95
(4-up)
$39.95
L/R Audio Balun
Use to send two channels of unbalanced line level
audio over Cat 5 cable. This balun features two 8"
pigtail leads, each terminated with gold plated
male RCA connectors, color coded red and white,
and a single female RJ-45 jack. Utilizes two
Cat 5 cable pairs: •Red: Pin 1/2 •White: Pin 3/6
Specifications: •Bandwidth: 10Hz~50KHz
•Distance: 1000' max (Cat 5) •Dimensions
(excluding cables): 0.85" (H) x 1.69" (W) x 1.94" (L)
Order #
50-7724
MSRP
$69.95
(1-3)
$39.95
(4-up)
$33.95
Back
L/R Audio Balun
Back
13
Component Video Balun
Use to send Y/Pb/Pr component video signals over
Cat 5 cable. This balun features three gold plated
female RCA connectors, color coded red, green and
blue, and a single female RJ-45 jack. Utilizes three
Cat 5 cable pairs: •Red: Pin 7/8 •Green: Pin 3/6
•Blue: Pin 1/2. Specifications: •Bandwidth:
50Hz~8MHz •Dimensions (excluding connectors):
1.0" (H) x 3.2" (W) x 2.4" (L)
Order #
50-7720
MSRP
$99.95
(1–3)
$58.95
Back
L/R Audio/Video Balun
(4–up)
$49.95
Back
Use to send composite video, plus two channels
of unbalanced line level audio over Cat 5 cable.
This balun features three gold plated female RCA
connectors, color coded red, white and yellow, and
a single female RJ-45 jack. Utilizes three Cat 5 cable
pairs: •Red: Pin 1/2 •White: Pin 3/6 •Yellow: Pin
7/8. Specifications: •Video bandwidth: 50Hz~8MHz
•Audio bandwidth: 10Hz~50KHz •Dimensions
(excluding connectors): 1.0" (H) x 2.36" (W) x 3.22" (L)
Order #
50-7730
MSRP
$79.95
(1–3)
$46.95
MSRP
$25.95
(1-3)
$15.29
(4-up)
$12.95
Video Balun
Use to send composite video signal over Cat 5
cable. This balun features a gold plated female
RCA connector, and female RJ-45 jack. Screw
terminals are available for connecting unterminated
Cat 5 cable. Utilizes one pair (pin 7/8) of Cat 5 cable.
Specifications: •Maximum distance: 1000'
•Bandwidth: 50Hz~8MHz •Dimensions (excluding
connector): 1.0" (H) x 0.85" (W) x 2.0" (L)
Order #
50-7710
MSRP
$34.95
(1–3)
$18.95
Back
Order #
50-7748
224
MSRP
$25.95
(1-3)
$15.29
(4-up)
$13.59
(1–3)
$35.95
(4–up)
$30.95
#50-7768
Use to send up to four independent
composite video signals over a
single Cat 5 run. Baluns are
available with either female
RCA or BNC connectors, allowing
compatibility with a wide variety
#50-7769
of multimedia and security
applications. They are also compatible with RGB
and component video signal formats. Baluns feature
female BNC or RCA connectors, and a single female
RJ-45 jack. Utilizes four Cat 5 cable pairs, baluns may
be inter mixed. Specifications: •Video bandwidth:
50Hz~8MHz •Distance: 1000' max (Cat 5)
•Dimensions (excluding connectors): 1.0" (H) x
2.28" (W) x 3.22" (L)
Order #
50-7768
50-7769
Connectors
RCA
BNC
MSRP
$74.95
74.95
(1-3)
$44.95
44.95
(4-up)
$38.25
38.25
Two Channel Balanced Audio Balun
Send two balanced channels of line level audio over a single
Cat 5 cable at distances of up to 1000'. Rugged steel housing
features two XLR connectors on one side, and a single female
RJ-45 connector on the other. Compatible with commonly
available pre-terminated network cables, the unit includes
full termination instructions. Specifications: •Frequency
#50-7728
response: 10Hz~50KHz, -0.5dB, +4dB •THD: 0.1% @1KHz
•Dimensions: 1.1" (H) x 3.5" (W) x 2.5" (D) •Male and female models
may be intermixed •Sold individually, baluns must be used in pairs
1-800-543-4330
Fax 1-800-765-6960
(4–up)
$16.95
#50-7727
RCA Composite Video Balun
Use to send composite video signal over Cat 5 cable, this balun
features very compact size, and a male RCA connector for easy
attachment directly to equipment including monitors, VCRs, DVD
players, processors and cameras. A specially designed tool-less
IDC connector provides quick, reliable connection to unterminated
Cat 5 cable. Specifications: •Bandwidth: 50Hz~8MHz •Distance:
1000' max, using 24AWG UTP •Dimensions (excluding connector):
0.813" (H) x 0.813" (W) x 1.875" (L)
MSRP
$59.95
Four Channel Video Baluns
Line Level
Audio Balun
Order #
50-7742
Order #
50-7725
(4–up)
$39.95
Back
Use to send a single channel of line level audio over
Cat 5 cable, this compact balun features a male RCA
connector for easy attachment directly to equipment.
Multiple baluns may be used to accommodate
numerous audio channels. A specially designed toolless IDC connector provides quick, reliable connection
to unterminated Cat 5 cable. Specifications:
•Bandwidth: 50Hz~8MHz •Distance: 1000' max
(Cat 5) •Dimensions (excluding connector): 0.813" (H)
x 0.813" (W) x 1.875" (L)
Use to send two channels of
unbalanced line level audio
over Cat 5 cable. This balun
features two gold plated female
RCA connectors, color coded red
and white, and a single female RJ-45 jack. Utilizes
two Cat 5 cable pairs: •Red: Pin 1/2 •White: Pin
3/6. Specifications: •Maximum distance: 1000'
•Bandwidth: 10Hz~50KHz •Dimensions (excluding
connectors): 0.85" (H) x 1.69" (W) x 1.94" (L)
Order #
50-7727
50-7728
XLR
Female
Male
MSRP
$109.00
109.00
(1-3)
$63.95
63.95
(4-up)
$57.95
57.95
C53_pg_224-225
8/13/08
10:35 AM
Page 225
SATV/CATV
Keystone Mount Category 5 Baluns
Compact individual baluns combine the advantages of Cat 5 cable for interconnecting
A/V components over long distances, with the flexibility of Keystone wall plates. The rear
of the balun features a specially designed tool-less IDC connector for easy connection of
unterminated Cat 5 cable. The front is a RCA female connector. Configure Keystone wall
plates with exactly the connections that are needed for each independent application. Baluns
are effective at distances from 400'~1000' depending on model, and may be intermixed with
other MCM Custom Audio Baluns. Sold individually, all baluns must be used in pairs.
section
13
#50-10255
See additional BNC
type baluns in the
security section.
See page 243.
#50-10265
and 50-10270
#50-10250
Keystone Mount Composite Video Balun
Intended to send composite video signal over Cat 5
cable, this balun features an RCA female connector
with yellow insert, for easy identification as the video
path. Rear mounted IDC connector allows simple,
fast connection to unterminated Cat 5 cable.
Maximum distance: 1000'. Sold individually.
Order #
50-7715
MSRP
$34.95
(1-3)
$18.95
(4-up)
$16.25
VGA Balun Series
Keystone Mount Component Video Baluns
Intended to send Y/Pb/Pr component video signals
over Cat 5 cable, these baluns are sold as individual
red, blue and green units. Internally identical units
feature RCA female connectors with the appropriate
color code insert, for easy identification of each video
signal path. Rear mounted IDC connector allows
simple, fast connection to unterminated Cat 5 cable.
Sold individually.
Order #
50-7765
50-7766
50-7767
Keystone Mount Composite Video Balun
Color
Red
Blue
Green
MSRP
$34.95
34.95
34.95
(1-3)
$19.95
18.95
18.95
(4-up)
$15.29
15.29
15.29
Intended to send composite video signal over Cat 5
cable, this balun features a BNC female connector
and is ideal for use in video surveillance applications.
Rear mounted IDC connector allows simple, fast
connection to unterminated Cat 5 cable. Maximum
distance: 1000'. •Sold individually
MSRP
$34.95
(1-3)
$18.95
Order # Type
50-10250 In-line
50-10255 In-line
50-10265 Wall plate
50-10270 Wall plate
Intended to send line level audio signals over Cat 5
cable, these baluns are sold as individual red and
white units. Internally identical units feature RCA
female connectors with the appropriate color code
insert, for easy identification of left or right audio
channel. Rear mounted IDC connector allows
simple, fast connection to unterminated Cat 5 cable.
Maximum distance: 1000'. Sold individually.
Keystone Mount Digital Audio Balun
Intended to send digital audio (SPDIF) signal over
Cat 5 cable, this balun features an RCA female
connector with orange insert, for easy identification as
the digital audio path. Rear mounted IDC connector
allows simple, fast connection to unterminated Cat 5
cable. Maximum distance: 1000'. Sold individually.
MSRP
$34.95
(1-3) (4-up)
$44.95 $37.95
44.95 37.95
44.95 37.95
44.95 37.95
(4-up)
$16.25
Keystone Audio Baluns
Order #
50-7755
VGA
Side Connector MSRP
PC
Male $99.95
Monitor Female 99.95
Monitor Female 99.95
PC
Female 99.95
13
Order #
50-7716
Ideal when computer monitor or other high
resolution video signal needs to be sent long distances.
Cable runs are greatly eased by the use of smaller,
lower cost Cat 5 UTP cable. These are perfect for
installation of multimedia systems in educational
environments, boardrooms and public areas. All units
consist of an HD-15 connector for connection to the PC
or monitor, and a female RJ-45 for connection to the
UTP cable. Four different configurations are available,
allowing a wide variety of installation possibilities.
Distance (Cat 5): •VGA (640 x 480): 450' •SVGA
(800 x 600): 350' •XGA (1024 x 768): 250' •SXGA
(1280 x 1024): 200' Note: Baluns are sold individually
and must be used in pairs. A pair must include one
PC side balun and one monitor side balun.
(1-3)
$18.95
Order #
50-7760
50-7761
Color
Red
White
MSRP
$36.95
36.95
(1-3)
$20.95
20.95
(4-up)
$17.95
17.95
(4-up)
$16.25
L/R Audio Plus S–Video Balun
Use to send S–video, plus two
channels of unbalanced line level
Back
audio, over Cat 5 cable. Independent
balun circuits provide separate
paths for chroma and luminance
signals, and left and right audio
signals, utilizing four pairs of Cat 5
cable. This balun features a female
4 pin S–video connector, two gold
plated female RCA connectors, color
coded red and white, and a female RJ-45 jack.
Specifications: •Pairs utilized: Luminance 7/8,
Chroma, 4/5, Audio (red) 1/2, •Audio (white) 3/6
•Video bandwidth: DC~6MHz •Audio bandwidth:
10KHz~50KHz •Dimensions (excluding connectors):
1.0" (H) x 2.36" (W) x 3.22" (L)
Order #
50-7740
MSRP
$99.95
(1–3)
$58.95
(4–up)
$51.95
Keystone Mount 3.5mm Connector
Keystone Mount DC Power Connection
This keystone insert features a standard barrel jack
which accepts connection from most AC adaptors.
It is essential when low voltage must be inserted
into a Cat 5 pair for remote distribution. It is ideal
for remote powering of small LCD monitors, video
cameras, IR repeater systems and similar items. Rear
mounted IDC connector allows simple, fast connection
to unterminated 22~24AWG solid or stranded wire.
Maximum voltage: 24VAC/DC, 1A. Barrel size: 2.1mm
I.D., 5.5mm O.D. •Sold individually
Order #
50-7752
MSRP
$11.95
(1-3)
$6.99
(4-up)
$5.95
This keystone insert features a standard 3.5mm
three-conductor female jack which may be used in
two or three conductor applications. It is ideal any
time a 3.5mm connector is needed at a wall plate.
Rear mounted IDC connector allows simple, fast
connection to unterminated Cat 5 cable, or any
22~24AWG solid or stranded, UTP or shielded wire.
Maximum voltage: 24VAC/DC, 1A. Applications:
•Remote location of headphone jacks •Remote
microphone connections •Remote input from PC
sound card, MP3 player or iPod™ •IR repeater
connection •Remote triggering of A/V components
•Low voltage DC connection •Sold individually
Order #
50-7753
MSRP
$12.95
(1-3)
$7.39
(4-up)
$6.29
www.mcmelectronics.com
S–Video Balun
Use to send S–video signal over
Cat 5 cable. Independent balun
circuits provide separate paths
for chroma and luminance signals,
utilizing two pairs of Cat 5 cable.
This balun features a female 4 pin
S–video connector, and female RJ-45
jack. Utilizes pin 7/8 (luminance) and
pin 4/5 (chroma). Specifications:
•Bandwidth: DC~6MHz •Dimensions:
1.19" (dia.) x 2" (L)
Order #
50-7735
NET 30
Terms
MSRP
$39.95
(1–3)
$23.95
Back
(4–up)
$20.95
225