Epson P07303 User manual

User Manual
June 2008 Revision 1.7
P07303 Series
Customer Display
Copyright 2008’ August
All Rights Reserved
Manual Version 1.7
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not
limited to, the implied warranties of merchantability and fitness for a particular
purpose. We shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use
of this material.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced or translated to another language without the prior written consent
of the manufacturer.
General Notice: All the company names used herein are for identification
purposes only and may be trademarks of their respective companies.
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrial power supply, turn off the
power switch and remove the power cord plug from the wall socket. The
wall socket must be easily accessible and in close proximity to the
machine.
2. Read these instructions carefully. Save these instructions for future
reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart,stand,or table.The product
may fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for
ventilation;to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered.The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surface.This product should never be placed near or
over a radiator or heat register,or in a built-in installation unless proper
ventilation is provided.
7. This product should be operated from the type of power indicated on the
marking label.If you are not sure of the type of power available, consult
your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product
where persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short out parts that could result
in a fire or electric shock.Never spill liquid of any kind on the product.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference
that may cause undesired operation.
CE Mark
This device complies with the requirements of the EEC directive
89/336/EEC with regard to “Electromagnetic compatibility” and
73/23/EEC “Low Voltage Directive”.
LEGISLATION AND WEEE SYMBOL
2002/96/EC Waste Electrical and Electronic Equipment Directive on the
treatment, collection, recycling and disposal of electric and electronic
devices and their components.
The crossed dustbin symbol on the device means that it should not be
disposed of with other household wastes at the end of its working life. Instead,
the device should be taken to the waste collection centers for activation of the
treatment, collection, recycling and disposal procedure.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of wastes
and recycle it responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can
take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
P07303 Series Customer Display User's Manual
Revision History
Revision
Description
Number
1.7
Added support for additional
character sets
Revision Date
2008 June
Table of Contents
A. 2 X 20 CUSTOMER DISPLAY
1. CHECKLIST ....................................................................................... 8
2. FEATURES ........................................................................................ 8
3. SPECIFICATION................................................................................ 9
4. INTERFACE ..................................................................................... 10
4.1.
4.2.
4.3.
SPECIFICATION .............................................................................................. 10
DISPLAY BASE............................................................................................... 10
CONNECTOR ................................................................................................. 10
5. DIP SWITCH AND SOFTWARE SETTING...................................... 12
5.1.
5.2.
5.3.
5.4.
5.5.
COMMAND TYPE SELECTION .......................................................................... 12
BAUD RATE SELECTION ................................................................................. 12
PARITY CHECK SELECTION ............................................................................. 12
COMMAND CONTROL ..................................................................................... 12
INTERNATIONAL CHARACTER SET ................................................................... 13
6. SOFTWARE STATUS SETTING COMMANDS ............................... 14
6.1.
6.2.
6.3.
6.4.
6.5.
BAUD RATE SETTING COMMAND ..................................................................... 14
PARITY CHECK SETTING COMMAND ................................................................ 14
INTERNATIONAL CHARACTER SET SETTING COMMAND ...................................... 15
COMMAND TYPE SETTING COMMAND .............................................................. 16
SHOW FIRMWARE VERSION ............................................................................ 16
7. COMMAND LIST TABLE.................................................................. 17
8. COMMAND DETAILS ...................................................................... 19
8.1.
8.2.
8.3.
8.4.
8.5.
8.6.
8.7.
8.8.
POS7300 SERIES COMMAND LIST ................................................................. 19
CD5220 STANDARD MODE COMMAND LIST..................................................... 21
UTC STANDARD MODE COMMAND LIST .......................................................... 24
UTC ENHANCED MODE COMMAND LIST .......................................................... 24
AEDEX/EMAX MODE COMMAND LIST ........................................................... 25
ADM787/788 MODE COMMAND LIST ............................................................... 25
DSP800 MODE COMMAND LIST ..................................................................... 26
EPSON ESC/POS COMMAND LIST ............................................................... 27
9. CHARACTER SET........................................................................... 29
9.1.
9.2.
CHARACTER CODE 20H – 7EH ...................................................................... 29
CHARACTER CODE 80H – FFH ...................................................................... 30
10. DISPLAY MODULE DIMENSION .................................................... 36
P07303 Series Customer Display User's Manual
B. 1 X 12 CUSTOMER DISPLAY
1. CHECKLIST ..................................................................................... 37
2. FEATURES ...................................................................................... 37
3. SPECIFICATION.............................................................................. 38
4. INTERFACE ..................................................................................... 39
4.1.
4.2.
4.3.
INTERFACE SPECIFICATION ............................................................................. 39
DISPLAY BASE............................................................................................... 39
CONNECTOR ................................................................................................. 39
5. COMMAND LIST TABLE.................................................................. 41
6. COMMAND DETAILS ...................................................................... 43
7. CHARACTER SET........................................................................... 48
8. DISPLAY MODULE DIMENSION .................................................... 49
(2 X 20 CUSTOMER DISPLAY AND 1 X 12 CUSTOMER DISPLAY)
APPENDIX A - COMMAND DETAILS .................................................... 50
APPENDIX B - CONTROL CODE SET.................................................. 53
7
P07303 Series Customer Display User's Manual
A. 2 x 20 Customer Display
1. Checklist
G
501 mm
225 mm
191 mm
281 mm
93 mm
Pole Display Module
Flat Cable (DB-9P to DB-9P
Flat Cable Connector)
Base Unit
Two Pieces of Pole Support
(1x22cm, 1x9cm)
Installation Guide
Power Adapter
2. Features
1. Data can be display on 20 columns x 2 lines.
2. Blue–green color and large character are easy to see.
3. The DIP switches setting emulate commands mode, baud rate and
international character.
4. Command emulation modes include: POS7300, EPSON ESC/POS, ADM787/
ADM788, DSP800, AEDEX/ EMAX, UTC, and CD5220.
5. Display area can be controlled by window function.
6. Provides an interface based in RS-232C, and RS232C baud rate from 4800 to
38400 bps.
7. Reverse characters can be specified using the Epson command set.
8
P07303 Series Customer Display User's Manual
3. Specification
NO
Item
Description
1
Display method
Vacuum fluorescent display
2
Number of character
3
Character font
5 x 7 Dot matrix
4
Display color
Blue green
5
Brightness
700 cd /㎡
6
Character type
7
Character size
8
Power supply
9
Power consumption
3-6W
10
MTBF
25000 hours (power on time)
11
Panel dimensions
224 (W) x 93 (H) x 50(D) mm
12
Support dimensions
13
Base dimensions
190(w)x55(h)x96(d)mm
14
Viewing angle
-5 - 60 degrees
15
Rotation angle
Maximum 270 degrees
16
Weight
1.25 Kg
17
Operating temperature
5 – 45oC
18
Operating Humidity
30%-85%
19
Storage Temperature
-10 - 55 oC
20
Storage Humidity
10%-85%
40 characters
(20 columns x 2 lines)
96 alphanumeric
13 kinds of international character set
9.0mm x 5.25mm
11-19VDC
Manufacture offer +12V power adapter
Long support :
22 cm
Short support :
9 cm
9
P07303 Series Customer Display User's Manual
4. Interface
4.1.
Specification
Data transmission
Serial
Synchronization
Asynchronous
Handshaking
DTR / DSR
MARK = -3 to –15 V (logic “1”)
Signal level
SPACE = +3 to +15 V (logic “0”)
4.2.
Baud rates
4800,9600,19200,38400 bps
Parity
None, even
Bit length
8 bits
Stop bits
1 bit
Display Base
The picture below shows the configuration of the stand alone VFD Pole Display
base.
Figure of VFD Pole Display Base
4.3.
Connector
PWR
COM
RJ45
10
P07303 Series Customer Display User's Manual
PWR: Power input connector from adapter
„ Connector type: DC jack (5.5/2.1)
„ Pin assignment
No
Signal
+
Vin
GND
RJ45: Connect to display panel
„ Connector type: Phone-jack 10P/8C
10
1
COM: RS232C link to PC/HOST connector (9-pin)
„ Connector type: D-sub 9 pin female
1
5
6
9
11
P07303 Series Customer Display User's Manual
5. Dip Switch and Software Setting
5.1.
Command Type Selection
SW1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
5.2.
SW2
ON
ON
OFF
OFF
ON
ON
OFF
OFF
SW9
ON
ON
OFF
OFF
Demo Mode Support
No
Yes
No
Yes
No
No
No
Yes
Baud Rate (bps)
4800
9600
19200
38400
Default
*
Parity Check Selection
SW10
ON
OFF
5.4.
Command Type
POS7300
EPSON ESC/POS
ADM 787/ ADM 788
DSP800
AEDEX/ EMAX
UTC/P
UTC/S
CD5220
Baud Rate Selection
SW8
ON
OFF
ON
OFF
5.3.
SW3
ON
ON
ON
ON
OFF
OFF
OFF
OFF
Parity Check
None-parity
Even-parity
Default
*
Command Control
SW12
ON
OFF
Function
Depend on SW1~SW11 setting
Bypass SW1~SW11 setting, fixed at:
¾ Command type: POS7300,
¾ Baud rate: 9600
¾ Parity check: None-parity
¾ Demo mode: Disable
¾ International char set: USA, standard Europe
12
Default
*
P07303 Series Customer Display User's Manual
5.5.
International Character Set
ID
SW SW SW SW SW Character Set
4
5
6
7
11
(20h – 7Fh)
0
ON ON ON ON OFF U.S.A.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
Code Table
(80H-FFH)
Default Note
CP-437
(USA, Standard Europe)
OFF FRANCE
OFF GERMANY
OFF U.K.
OFF DENMARK I
OFF SWEDEN
OFF ITALY
OFF SPAIN
OFF JAPAN
OFF NORWAY
OFF DENMARK II
OFF Slawie
OFF RUSSIA
OFF U.S.A
OFF U.K.
OFF U.S.A
ON U.S.A
ON U.S.A
ON U.S.A
ON U.S.A
ON U.S.A
ON U.S.A
ON U.S.A
ON U.S.A
ON U.S.A
13
CP-858
(Multilingual
Symbol)
+
Euro
Katakana
CP-858
(Multilingual+ Euro Symbol)
CP-860 (Portuguese)
Greek
CP-852 (Hungary)
CP-862 (Hebrew)
CP-863 (Canadian-French)
CP-865 (Nordic)
CP-866 (Cyrillic)
Windows-1251 (Cyrillic)
Windows-1252
Windows-1255 (Hebrew)
Windows-1257 (Baltic)
Windows-1253 (Greek)
*
P07303 Series Customer Display User's Manual
6. Software Status Setting Commands
When the system is POWER ON, it will read the DIP switch to set the Command
Type, Baud Rate, Parity, Demo Mode and International Character. User can
re-set the Software Status Setting Commands as following:
6.1.
Baud Rate Setting Command
STX 05 B n ETX
ASCII Format
Dec. Format
Hex. Format
Description
/Change the baud rate setting/
STX 05 B n ETX
[02] [05] [66] n [03]
[02h][05h][42h] n
30h≦n≦33h
[
0
3
h
]
Change the display communication baud rate. The baud
rate setting can be selected from 4800 to 38400.
n
30h
31h
32h
33h
6.2.
Baud rate
4800
9600
19200
38400
Parity Check Setting Command
STX 05 P n ETX
ASCII Format
Dec. Format
Hex. Format
Description
/Change the Parity check setting/
STX 05 P n ETX
[02] [05] [80] n [03]
[02h][05h][50h] n [03h]
n=30h, 31h
Change the display communication parity. Set 8 data bit
and the parity set for even or non-parity.
n
30h
31h
Parity check
None-parity
Even-parity
14
P07303 Series Customer Display User's Manual
6.3.
International Character Set Setting Command
STX 05 S n ETX
ASCII Format
Dec. Format
Hex. Format
Description
n
/Change the international character set/
STX 05 S n ETX
[02] [05] [83] n [03]
[02h][05h][53h] n
30h≦n≦4Fh
[
0
3
h
]
Change the display international character font.
Character Set
(20h – 7Fh)
30h
U.S.A.
31h
32h
33h
34h
35h
36h
37h
38h
39h
3Ah
3Bh
3Ch
3Dh
3Eh
3Fh
40h
41h
42h
43h
44h
45h
46h
47h
48h
FRANCE
GERMANY
U.K.
DENMARK I
SWEDEN
ITALY
SPAIN
JAPAN
NORWAY
DENMARK II
Slawie
RUSSIA
U.S.A
U.K.
U.S.A
U.S.A
U.S.A
U.S.A
U.S.A
U.S.A
U.S.A
U.S.A
U.S.A
U.S.A
Code Table
(80H-FFH)
CP-437
(USA, Standard Europe)
CP-858
(Multilingual + Euro Symbol)
Katakana
CP-858
(Multilingual+ Euro Symbol)
CP-860 (Portuguese)
Greek
CP-852 (Hungary)
CP-862 (Hebrew)
CP-863 (Canadian-French)
CP-865 (Nordic)
CP-866 (Cyrillic)
Windows-1251 (Cyrillic)
Windows-1252
Windows-1255 (Hebrew)
Windows-1257 (Baltic)
Windows-1253 (Greek)
15
Note
P07303 Series Customer Display User's Manual
6.4.
Command Type Setting Command
/Change the command type setting/
STX 05 C n ETX
[02] [05] [67] n [03]
[02h][05h][43h] n
30h≦ n ≦37h
[
0
3
h
]
This command will change the command type and
initialize the display.
The display emulation mode is based on DSP800/ ESC/
ADM 787/ POS7300/ AEDEX/ UTC/ CD5220 mode.
STX 05 C n ETX
ASCII Format
Dec. Format
Hex. Format
Description
n
30h
31h
32h
33h
6.5.
Command Type
POS7300
ESC/POS
ADM 787
DSP800
Command Type
AEDEX
UTC/P
UTC/S
CD5220
Run Demo message
STX 05 D 08 ETX
ASCII Format
Dec. Format
Hex. Format
Description
6.6.
n
34h
35h
36h
37h
/Run demo message/
STX 05 D 08 ETX
[02][05][68][08][03]
[02h][05h][44h][08h][03h]
Run demo message for the display.
The display emulation mode is based on DSP800,
EPSON ESC/POS, CD5220 command type.
Show Firmware Version
STX 05 V 01 ETX
ASCII Format
Dec. Format
Hex. Format
Description
/Show Firmware Version/
STX 05 V 01 ETX
[02][05][86][01][03]
[02h][05h][56h][01h][03h]
Show firmware version.
16
P07303 Series Customer Display User's Manual
7. Command List Table
Command List Table – 1
POS730 CD522 EPSON UTC/ UTC/
ADM78 DSP80
AEDEX
0
0
D101
S
P
8
0
Move cursor right
Move cursor left
Move cursor up
Move cursor down
Move cursor to right-most
position
Move cursor to left-most
position
Move cursor to home position
Move cursor to bottom
position
Move cursor to specified
position
Clear display screen
Clear cursor line
Brightness adjustment
Blink display screen
Initialize display
Select character code table
Select international character
set
Select/cancel reverse
character
Overwrite mode
Vertical scroll mode
Horizontal scroll mode
Set/cancel the window range
Select peripheral device
Set starting/ending position
of macro definition
Execute and quit macro
Execute self-test
Display time
Display time continuously
Display position
Cursor on/off
Change to UTC enhanced
mode
Change to UTC standard
mode
Write string to upper line
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
17
O
P07303 Series Customer Display User's Manual
Command List Table – 2
POS730 CD522 EPSON UTC/ UTC/
ADM78 DSP80
AEDEX
0
0
D101
S
P
8
0
Upper line message
continuous scroll
Bottom line message scroll
continuously
Message vertical down scroll
continuously
Message vertical upper scroll
continuously
Carriage return
Line feed
Back space
Horizontal tab
Command type select
Upper line message scroll
once pass
Change attention code
Two line display
Clear upper line and move
cursor to upper left-end
position
Clear bottom line and move
cursor to bottom left-end
position
Set period to upper line, last
n position
Set line blinking, upper line
Clear line blinking, upper line
Clear field 1 and move cursor
to field 1, first position
Clear field 2 and move cursor
to field 2,first position
Clear display range from n
position to m position and
move cursor to n position
Save the current displaying
data to n layer for demo
display
Turn annunciator on/off
Specify period
Specify comma
Specify semicolon (period +
comma)
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
18
P07303 Series Customer Display User's Manual
8. Command Details
8.1.
POS7300 Series Command List
POS7300 Standard Mode Command List-1
Command
ESC F A
[DATA] CR
ESC F B
[DATA] CR
ESC F D
[DATA] CR
ESC F O
[DATA] CR
ESC P x y
ESC _ n
ESC DC1
ESC DC2
ESC DC3
ESC @
US MD1 n
US MD2 n
US DC1 n
US DC2 n
US E n
NULL H
NULL K
NULL M
NULL P
NULL G
NULL O
Code (hex)
1B 46 41 [DATA] 0D
Function Description
Write string to upper line
¾ Maximal [DATA] length is 40
1B 46 42 [DATA] 0D Write string to lower line
¾ Maximal [DATA] length is 40
1B 46 44 [DATA] 0D Upper line message scroll continuously
¾ Maximal [DATA] length is 40
1B 46 4F [DATA] 0D Bottom line message scroll continuously
¾ Maximal [DATA] length is 40
1B 50 x y
Move cursor to specified position
¾ x = 1 ~ 14h, for columns location.
¾ y = 1 ~ 2, for lines location.
1B 5F n
Set cursor on/off
¾ n = 00 ~ 01
1B 11
Overwrite mode
1B 12
Vertical scroll mode
1B 13
Horizontal scroll mode
1B 40
Initialize display
1F 01 n
Message vertical upper scroll continuously
¾ n = 01 ~ 0Ch
1F 02 n
Message vertical down scroll continuously
¾ n = 01 ~ 0Ch
1F 11 n
Set line blinking
¾ n = ’1’ ~ ’2’
„ n = ’1’ up line
„ n = ’2’ low line
1F 12 n
Clear line blinking
¾ n = ’1’ ~ ’2’
„ n = ’1’ up line
„ n = ’2’ low line
1F 45 n
Blink display screen
¾ n = 00h ~ FFh
„ n = 0 for no blink
0 48
Move cursor up
0 4B
Move cursor left
0 4D
Move cursor right
0 50
Move cursor down
0 47
Move cursor to left-most position
0 4F
Move cursor to right-most position
19
P07303 Series Customer Display User's Manual
POS7300 Standard Mode Command List-2
Command
BS
HT
LF
HOM
CLR
CR
CAN
ESC = n
Code (hex)
08
09
0A
0B
0C
0D
18
1B 3D n
Function Description
Back space
Horizontal tab
Line feed
Move cursor to home position
Clear display screen
Carriage return
Clear cursor line, and clear string mode
Select peripheral device, display or printer
¾ n = 1~3
„ n = '1': enable printer only
„ n = '2': enable display only
„ n = '3': enable both of printer and
display
20
P07303 Series Customer Display User's Manual
8.2.
CD5220 Standard Mode Command List
CD5220 Standard Mode Command List-1
Command
ESC DC1
US SOH
ESC DC2
US STX
ESC DC3
US ETX
ESC Q [DATA]
CR
Code (hex)
1B 11
1F 01
1B 12
1F 02
1B 13
1F 03
1B 51 41 [DATA]
0D
ESC Q [DATA]
CR
1B 51 42 [DATA]
0D
ESC Q [DATA]
CR
ESD [ D
BS
ESC [ C
HT
ESC [ A
US LF
ESC [ B
LF
ESC [ H
HOM
ESC [ L
CR
ESC [ R
US CR
ESC [ K
US B
ESC # n
1B 51 44 [DATA]
0D
1B 5B 44
08
1B 5B 43
09
1B 5B 41
1F 0A
1B 5B 42
0A
1B 5B 48
0B
1B 5B 4C
0D
1B 5B 52
1F 0D
1B 5B 4B
1F 42
1B 23 n
US @
US E n
1F 40
1F 45 n
ESC I x y
1B 6C x y
US $ x y
1F 24 x y
ESC @
1B 40
Function Description
Overwrite mode
Vertical scroll mode
Horizontal scroll mode
Set the string display mode, write string to
upper line. *1
¾ Maximal [DATA] length is 20
Set the string display mode, write string to
lower line. *1
¾ Maximal [DATA] length is 20
Upper line message scroll continuously. *1 *2
¾ Maximal [DATA] length is 40
Move cursor left
Move cursor right
Move cursor up
Move cursor down
Move cursor to home position
Move cursor to left-most position
Move cursor to right-most position
Move cursor to bottom position
Command type select
¾ n = 30h ~ 37h
Execute self test
Blink display screen
¾ n = 00h ~ FFh
„ n = 0 for no blink
Move cursor to specified position
¾ x = 1 ~ 14h, for columns location.
¾ y = 1,2, for lines location.
Initialize display
21
P07303 Series Customer Display User's Manual
CD5220 Standard Mode Command List-2
Command
Code (hex)
ESC W s x1 x2 1B 57 s x1 x2 y
y
CLR
CAN
ESC * n
US X n
ESC _ n
0C
18
1B 2A n
1F 58 n
1B 5F n
ESC f n
1B 66 n
ESC c n
1B 63 n
ESC = n
1B 3D n
Function Description
Set or cancel the window range at
horizontal scroll mode
¾ 1 ≦ x1 ≦ x2 ≦ 14h, for columns
location.
¾ y = 1~2, for lines location.
¾ s = 0: cancel
s = 1: set
Clear display screen, and clear string mode
Clear cursor line, and clear string mode
Brightness adjustment
¾ n = 1 ~ 4, n = 4 for highest brightness
Set cursor on/off
¾ n = 1: cursor on
n = 0: cursor off
Select international fonts
¾ About n, refer. *3
Select fonts, ASCII code or JIS code,
¾ About n, refer. *4
Select peripheral device, display or printer
¾ n='1': enable printer only
n='2': enable display only
n='3': enable both of printer and display
Note:
1. While using command “ESC Q A” or “ESC Q B”, other commands cannot
be used except when using command “CLR” or “CAN” to change operating
mode.
2. When using command “ESC Q D”, the upper line message will scroll
continuously until a new command is received, it will then clear the upper
line and move the cursor to the upper left-end position.
3. The parameter of international fonts set control by command “ESC f n”.
Parameter “n”
International
Parameter “n”
International
Font Set
Font Set
Characte
Hex
Character
Hex
r
‘A’
41h
U.S.A.
‘W’
57h
Sweden
‘G’
47h
Germany
‘D’
44h
Denmark I
’I’
49h
Italy
‘E’
45h
Denmark II
‘J’
4Ah
Japan
‘L’
4Ch
Slavonic
‘U’
55h
U.K.
‘R’
52h
Russia
‘F’
46h
France
‘S’
53h
Spain
‘N’
4Eh
Norway
22
P07303 Series Customer Display User's Manual
4. The parameter of the code table control by command “ESC c n”.
Parameter “n”
International Font Set
Character
Hex
‘A’
41h Compliance with ASCII code (CP-437)
‘J’
4Ah Compliance with JIS code (Katakana)
‘L’
4Ch Compliance with Slawie code
‘R’
52h Compliance with RUSSIA code
‘M’
4Dh CP-850 (Multilingual)
‘P’
50h CP-858 (Multilingual+ Euro Symbol)
‘p’
70h CP-860 (Portuguese)
‘F’
46h CP-863 (Canadian-French)
‘N’
4Eh CP-865 (Nordic)
‘u’
75h CP-852 (Hungary)
‘H’
48h CP-862 (Hebrew)
‘C’
43h CP-866 (Cyrillic)
‘G’
47h Greek
‘c’
63h Windows-1251 (Cyrillic)
‘W’
57h Windows-1252
‘h’
68h Windows-1255 (Hebrew)
‘B’
42h Windows-1257 (Baltic)
‘g’
67h Windows-1253 (Greek)
23
P07303 Series Customer Display User's Manual
8.3.
UTC Standard Mode Command List
Command
BS
HT
LF
CR
DLE n
08
09
0A
0D
10 n
DC1
DC2
DC3
DC4
US
ESC d
11
12
13
14
1F
1B 64
8.4.
Code (hex)
Function Description
Back space
Horizontal tab
Line feed
Carriage return
Display position
¾ n = 0 ~ 27h, for location.
Over write display mode
Vertical scroll mode
Cursor on
Cursor off
Clear display
Change to UTC enhanced mode
UTC Enhanced Mode Command List
Command
ESC u A
[DATA] CR
ESC u B
[DATA] CR
ESC u D
[DATA] CR
ESC u E h h :
m m CR
ESC u F
[DATA] CR
ESC u H n m
CR
Code (hex)
1B 75 41 [DATA] 0D
Function Description
Upper line display
¾ Maximal [DATA] length is 20
1B 75 42 [DATA] 0D
Bottom line display
¾ Maximal [DATA] length is 20
1B 75 44 [DATA] 0D
Upper line message scroll continuously
¾ Maximal [DATA] length is 40
1B 75 45 h h ':' m m 0D Display time
¾ h, m = '0' ~ '9'
1B 75 46 [DATA] 0D
Upper line message scroll Once pass
¾ Maximal [DATA] length is 40
1B 75 48 n m 0D
Change attention code
¾ n = 1 ~ 20h
¾ m = 1 ~ 20h
ESC u I [DATA] 1B 75 49 [DATA] 0D
Two line display
CR
¾ Maximal [DATA] length is 40
ESC RS CR
1B 0F 0D
Change to UTC standard mode
24
P07303 Series Customer Display User's Manual
8.5.
AEDEX/EMAX Mode Command List
Command
Code (hex)
! # 4 [DATA] 21 23 34 [DATA] 0D
CR
! # 5 h h : m m 21 23 35 h h ':' m m 0D
CR
! # 8 n m CR 21 23 38 n m 0D
! # 9 [DATA]
CR
! # 6 [DATA]
CR
8.6.
21 23 39 [DATA] 0D
21 23 36 [DATA] 0D
Function Description
Upper line message scroll
¾ Maximal [DATA] length is 40
Display time
¾ h, m = '0' ~ '9'
Change attention code
¾ n, m = 1 ~ 20
Two line display
¾ Maximal [DATA] length is 40
Upper line message scroll once pass
¾ Maximal [DATA] length is 40
ADM787/788 mode command list
Command
CLR
CR
SLE1
Code (hex)
0C
0D
0E
SLE2
0F
DC0 n
10 n
DC1 n
11 n
DC2 n
12 n
SF1
1E
SF2
1F
Function Description
Clear display
Carriage return
Clear upper line and move cursor to
upper left-end position
Clear bottom line and move, Cursor to
bottom left-end position
Set period to upper line last n position
¾ n = 31H ~ 37H
Set line blinking, upper line
¾ n = '1' ~ '2'
„ n = '1': up line
„ n = '2': low line
Clear line blinking, upper line
¾ n = '1' ~ '2'
„ n = '1': up line
„ n = '2': low line
Clear field 1 and move cursor to field 1,
first position
Clear field 2 and move cursor to field 2,
first position
25
P07303 Series Customer Display User's Manual
8.7.
DSP800 Mode Command List
Command
EOT SOH I n ETB
EOT SOH P n ETB
EOT SOH C n m
ETB
EOT SOH S n ETB
EOT SOH D n m
ETB
EOT SOH A n ETB
EOT SOH F n ETB
EOT SOH # n ETB
EOT SOH % ETB
EOT SOH @ ETB
EOT SOH = n ETB
Code (hex)
04 01 49 n 17
Function Description
Select international character set
¾ n = 00 ~ 0Fh or 30 ~ 3Fh
04 01 50 n 17
Move cursor to specified position
¾ n = 31h ~ 58h
04 01 43 n m 17 Clear display range from n position to m
position and move cursor to n position
¾ 31h n m 58h
04 01 53 n 17
Save current view message to n layer for
demo view data
¾ n = 31h ~ 35h
04 01 44 n m 17 Display the saved demo message
¾ n = 31h ~ 4Fh
¾ m = 31h ~ 33h
04 01 41 n 17
Brightness adjustment
n =31h-34h
04 01 46 n 17
Blink display Screen
00h n FFh
¾ n = 00h ~ FFh, n = 0 for no blink
04 01 23 n 17
Command type select
n =30~37h
04 01 25 17
Initialize display
04 01 40 17
Execute self-test
04 01 3D n 17
Select peripheral device, display or printer
¾ n = '1': enable printer only
n = '2': enable display only
n = '3': enable both of printer and
display
26
P07303 Series Customer Display User's Manual
8.8.
EPSON ESC/POS Command List
EPSON ESC/POS Command List-1
Command Code (hex)
Function Description
US r n
1F 72 n
Select/cancel reverse character.
¾ n = 00,01
US MD1
1F 01
Specify overwrite mode.
US MD2
1F 02
Specify vertical scroll mode.
US MD3
1F 03
Specify horizontal scroll mode.
CAN
18
Clear cursor line
ESC # n
1B 23 n
Command type select
¾ n = 30h ~ 38h
US # n x
1F 23 n x
Turn annunciator on/off.
¾ n = 0 for annunciator off
n = 1 for annunciator on
¾ x = 1 ~ 14h, for columns location.
US C n
1F 43 n
Set cursor on/off
¾ n = 00, 01
BS
08
Move cursor left
HT
09
Move cursor right
US LF
1F 0A
Move cursor up
LF
0A
Move cursor down
US CR
1F 0D
Move cursor to right-most position
CR
0D
Move cursor to left-most position
HOM
0B
Move cursor to home position
US B
1F 42
Move cursor to bottom position
US $ x y
1F 24 x y
Move cursor to specified position
¾ x = 1 ~ 14h, for columns location.
¾ y = 1 ~ 2, for lines location.
CLR
0C
Clear display screen
US E n
1F 45 n
Blink display screen
¾ n = 00h ~ FFh
n = 0 for no blink
ESC @
1B 40
Initialize display
US . n
1F 2E n
Specify period
¾ n = a displayable character code
US , n
1F 2C n
Specify comma
¾ n = a displayable character code
US ; n
1F 3B n
Specify semicolon (period + comma)
¾ n = a displayable character code
US :
1F 3A
Set starting/ending position of macro definition.
Ex.: 1F 3A … (macro string) … 1F 3A
US @
1F 40
Execute self - test
US T h m
1F 54 h m
Display time
¾ 0 ≦ h ≦ 17h, for hours setting.
¾ 0 ≦ m ≦ 3Bh, for minutes setting.
27
P07303 Series Customer Display User's Manual
EPSON ESC/POS Command List-2
Command Code (hex)
Function Description
US ^ n m 1F 5E n m
Execute and quit macro. It’s an interval of n between
the two words. It’s an interval of m between the two
strings.
¾ 00 ≦ (n, m) ≦ FFh
„ n = Word time
„ m = show string time
US U
1F 55
Display time continuously
US X n
1F 58 n
Brightness adjustment
¾ n=1~ 4
ESC W n s 1B 57 n s x1 Set or cancel the window range
¾ n = 1 ~ 4, for window number
x1 y1 x2 y2 y1 x2 y2
¾ s = 0: cancel
s = 1: set
¾ 1 ≦ x1 ≦ x2 ≦ 14h, for columns location.
¾ 1 ≦ y1 ≦ y2 ≦ 2, for lines location.
ESC R n
1B 52 n
Select international character set (20H~7Fh).
¾ n = 00 ~ 0Fh. See note *1
ESC t n
1B 74 n
Select character code table (80H~FFh).
¾ n = 00 ~ 1Fh. See note *2
ESC = n
1B 3D n
Select peripheral device, display or printer
¾ n = '1': enable printer only
n = '2': enable display only
n = '3': enable both of printer and display
Note:
1. Select international character set (20H~7Fh) for command “ESC R n”
n
0h
1h
2h
3h
4h
5h
international character set
U.S.A.
FRANCE
GERMANY
U.K.
DENMARK I
SWEDEN
n
6h
7h
8h
9h
Ah
Bh
international character set
ITALY
SPAIN
JAPAN
NORWAY
DENMARK II
SLAVONIC
n
Ch
Dh
Eh
Fh
international character set
RUSSIA
Not used
Not used
Not used
2. Select character code table (80H~FFh) for command “ESC t n”
n character code table
0h CP-437 (USA, Standard
Europe)
1h Katakana (for Japan)
2h CP-850 (Multilingual)
3h CP-860 (Portuguese)
4h CP-863
(Canadian-French)
5h CP-865 (Nordic)
n character code table
6h Slawie
7h
8h
9h
Ah
Russia
Greek
CP-852 (Hungary)
CP-862 (Hebrew)
Bh CP-866 (Cyrillic)
28
n
character code table
Ch Windows-1251 (Cyrillic)
Eh
Fh
10h
11h
Windows-1255 (Hebrew)
Windows-1257 (Baltic)
Windows-1252
Windows-1253 (Greek)
13h CP-858 (Multilingual+
Euro Symbol)
P07303 Series Customer Display User's Manual
9. Character Set
9.1.
Character Code 20H – 7FH
9.1.1
International Character Sets
Character Code Number
Country
Hex 23
24
40
5B
5C
5D
5E
60
7B
Dec 35
36
64
91
92
93
94
96
123 124 125 126
#
#
#
£
#
#
#
Pt
#
#
#
#
#
$
$
$
$
$
¤
$
$
$
¤
$
$
$
@
à
§
@
@
É
@
@
@
É
É
@
@
[
°
Ä
[
Æ
Ä
°
¡
[
Æ
Æ
[
[
\
ç
Ö
\
Ø
Ö
\
Ñ
¥
Ø
Ø
\
\
]
§
Ü
]
Å
Å
é
¿
]
Å
Å
]
]
^
^
^
^
^
Ü
^
^
^
Ü
Ü
^
^
`
`
`
`
`
é
ù
`
`
é
é
`
`
{
é
ä
{
æ
ä
à
¨
{
æ
æ
{
{
U.S.A
France
Germany
U.K
Denmark I
Sweden
Italy
Spain
Japan
Norway
Denmark II
Slavonic
Russia
9.1.2
7C
¦
ù
ö
¦
ø
ö
ò
ñ
¦
ø
ø
¦
¦
7D
}
è
ü
}
å
å
è
}
}
å
å
}
}
7E
~
¨
β
~
~
ü
ì
~
~
ü
ü
~
~
USA, Standard Character Sets
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
20h
30h
40h
50h
60h
70h
0
@
P
`
p
!
1
A
Q
a
q
“
2
B
R
b
r
#
3
C
S
c
s
$
4
D
T
d
t
%
5
E
U
e
u
&
6
F
V
f
v
‘
7
G
W
g
w
29
( ) *
8 9 :
H I J
X Y Z
h i j
x y Z
+
;
K
[
k
{
, - . /
< = > ?
L M N O
\ ] ^ _
l m n o
¦ } ~
P07303 Series Customer Display User's Manual
9.2.
9.2.1
80h
90h
A0h
B0h
C0h
D0h
E0h
F0h
9.2.2
80h
90h
A0h
B0h
C0h
D0h
E0h
9.2.3
80h
90h
A0h
B0h
C0h
D0h
E0h
Ç
É
á
░
└
╨
α
≡
ü
æ
í
▒
┴
╤
ß
±
é
Æ
ó
▓
┬
╥
Γ
≥
â
ô
ú
│
├
╙
π
≤
ä
ö
ñ
┤
─
╘
Σ
⌠
à
ò
Ñ
╡
┼
╒
σ
⌡
å
û
ª
╢
╞
╓
μ
÷
ç
ù
º
╖
╟
╫
τ
≈
ê
ÿ
¿
╕
╚
╪
Φ
°
ë
Ö
⌐
╣
╔
┘
θ
•
è
Ü
¬
║
╩
┌
Ω
·
ï
¢
½
╗
╦
█
δ
√
î
£
¼
╝
╠
▄
∞
n
ì
¥
¡
╜
═
▌
ø
²
Ä
Pt
«
╛
╬
▐
ε
■
Å
ƒ
»
┐
╧
▀
∩
CP-850 (Multilingual)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
Ç
É
á
░
└
ð
ó
¯
ü
æ
í
▒
┴
Đ
ß
±
é
Æ
ó
▓
┬
Ê
ô
=
â
ô
ú
│
├
Ë
ò
¾
ä
ö
ñ
┤
─
È
õ
¶
à
ò
Ñ
Á
┼
l
Õ
§
å
û
a
Â
ã
Í
μ
÷
ç
ù
o
À
Ã
Î
þ
ê
ÿ
¿
©
╚
Ï
Þ
˚
ë
ö
®
╣
╔
┘
Ú
¨
è
Ü
¬
║
╩
「
Û
˙
ï
ø
½
╗
╦
█
Ù
1
î
£
¼
╝
╠
▄
ý
3
ì
Ø
¡
¢
═
¦
Ý
2
Ä Å
× ƒ
« »
¥ ┐
╬ ¤
Ì ▀
¯ ´
■
CP-858 (Multilingual + Euro Symbol)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
Ç
É
á
░
└
ð
ó
¯
ü
æ
í
▒
┴
Đ
ß
±
é
Æ
ó
▓
┬
Ê
ô
=
â
ô
ú
│
├
Ë
ò
¾
ä
ö
ñ
┤
─
È
õ
¶
à
ò
Ñ
Á
┼
€
Õ
§
å
û
a
Â
ã
Í
μ
÷
ç
ù
o
À
Ã
Î
þ
,
F0h
CP-437 (USA, Standard Europe)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
,
F0h
Character Code 80H – FFH
30
ê
ÿ
¿
©
╚
Ï
Þ
˚
ë
ö
®
╣
╔
┘
Ú
¨
è
Ü
¬
║
╩
「
Û
˙
ï
ø
½
╗
╦
█
Ù
1
î
£
¼
╝
╠
▄
ý
3
ì
Ø
¡
¢
═
¦
Ý
2
Ä Å
× ƒ
« »
¥ ┐
╬ ¤
Ì ▀
¯ ´
■
P07303 Series Customer Display User's Manual
9.2.4
Katakana for Japan
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
80h
α β γ ⊿ є η θ λ μ π ρ σ τ Ф Ω ∑
£ § IE IR ∫ x Ā -1 ² ³ x ½ 1/ √ ± ■
。 「 」 、 ‧
90h
A0h
B0h
C0h
D0h
E0h
F0h
9.2.5
80h
90h
A0h
B0h
C0h
D0h
E0h
F0h
≤
" ∘
” “ « » ∴ ∵
♁ Θ
≥ ≠ ≒ ║ │ ⊥ ∞ α ~ ~ ≣ 〒
Slawie
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
Ç ü é
é Ĺ í
á í ó
░ ▒ ▓
â
ô
ú
│
ä
ö
ą
┤
─
đ đ ď ë ď
ó β ô ń ń
– ̃ ֽ ˇ ˘
ů
Ľ
ą
á
┼
ň
ň
§
ć
ĭ
ž
â
ă
í
š
÷
ç
ś
ž
ĕ
ă
î
š
‫د‬
Į ë õ õ
ś Ö Ü ť
ę ę
ź
ş
ě
ŕ
˚
ú
¨
ŕ
˙
î
ť
č
ź
ł
ş
ŧ
═
█ ▄ ţ
ũ ý ý
ũ ř ř
ä
х
«
ŧ
ć
č
»
¤
ů ▀
ţ ́
■
9.2.6
Russia
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
80h
А Б В Г Д Е Ж З и Й К Л М Н О П
Р С Т У Ф Х Ц Ч Ш Щ Ъ Ы Ь Э Ю Я
а б в г д е ж з и й к л м н о п
90h
A0h
B0h
C0h
D0h
E0h
F0h
р с т у ф х ц ч ш щ ъ ы
∂ Ғ Қ Ң θ Ұ Y Һ ∂ ғ қ ң
31
ь
θ
Э ю
ұ Y
я
P07303 Series Customer Display User's Manual
9.2.7
80h
90h
A0h
B0h
C0h
D0h
E0h
F0h
9.2.8
CP-860 (Portuguese)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
Ç
É
á
░
└
╨
α
≡
ü
À
í
▒
┴
╤
β
±
é
È
ó
▓
┬
╥
Γ
≥
â
ô
ú
│
├
╙
π
≤
ã
õ
ñ
┤
─
╘
Σ
⌠
à
ò
Ñ
╡
┼
╒
σ
⌡
Á
Ú
a
╢
╞
╓
μ
÷
ç
ù
o
╖
╟
╫
τ
≈
ê
Ì
¿
╕
╚
╪
Ф
°
Ê
Õ
®
╣
╔
┘
θ
•
è
Ü
¬
║
╩
└
Ω
·
Í
¢
½
╗
╦
█
δ
√
Ô
£
¼
╝
╠
▄
∞
n
ì
Ù
¡
╜
═
▌
ø
²
Ã
Pt
«
╛
╬
▐
є
■
Â
Ó
»
┐
╧
▀
∩
Greek
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
80h
90h
A0h
Α Β Γ Δ Ε Ζ Η Θ Ι Κ Λ Μ Ν Ξ Ο Π
Ρ Σ Τ Y Φ Х Ψ Ω α β γ δ ε ζ η θ
ι κ λ μ ν ξ ο π ρ σ s τ υ φ χ ψ
B0h
C0h
D0h
E0h
ω
£
F0h
9.2.9
-
CP-852 (Hungary)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
80h
90h
A0h
B0h
C0h
D0h
E0h
F0h
Ç
É
á
░
└
đ
Ó
–
ű
Ĺ
í
▒
┴
Đ
ß
̃
é
ĺ
ó
▓
┬
Ď
Ô
ֽ
â
ô
ú
│
├
Ë
Ń
ˇ
ä
ö
Ą
┤
─
ď
ń
˘
ů
Ľ
ą
Á
┼
Ň
ň
§
ć
ľ
Ž
Â
Ä
Í
Š
÷
ç
Ś
ž
Ĕ
ǎ
Î
š
‫د‬
32
ł
ś
Ę
Ş
╚
ě
Ŕ
˚
ë
Ö
ę
╣
╔
┘
Ú
¨
Ő
Ü
¬
║
╩
г
ŕ
˙
ő
Ť
ź
╗
╦
█
Ű
ũ
î
ť
Č
╝
╠
▄
ý
Ř
Ź
Ł
ş
ż
═
Ţ
Ý
ř
Ä
x
«
ż
╬
Ů
ţ
■
Ć
Č
»
┐
¤
▀
´
P07303 Series Customer Display User's Manual
9.2.10
80h
90h
A0h
B0h
C0h
D0h
E0h
F0h
9.2.11
80h
90h
B0h
C0h
D0h
E0h
F0h
9.2.12
80h
90h
A0h
B0h
C0h
D0h
E0h
F0h
‫א‬
‫נ‬
á
░
└
╨
α
≡
‫ב‬
‫ס‬
í
▒
┴
╤
ß
±
‫ג‬
‫ע‬
ó
▓
┬
╥
Γ
≥
‫ד‬
‫ף‬
ú
│
├
╙
π
≤
‫ה‬
‫פ‬
ñ
┤
─
╘
Σ
⌠
‫ו‬
‫ץ‬
Ñ
╡
┼
╒
σ
⌡
‫ז‬
‫צ‬
ª
╢
╞
╓
µ
÷
‫ח‬
‫ק‬
º
╖
╟
╫
τ
≈
‫ט‬
‫ר‬
¿
╕
╚
╪
Φ
°
‫י‬
‫ש‬
⌐
╣
╔
┘
Θ
·
‫ך‬
‫ת‬
¬
║
╩
┌
Ω
·
‫כ‬
¢
½
╗
╦
█
δ
√
‫ל‬
£
¼
╝
╠
▄
∞
ⁿ
‫ם‬
¥
¡
╜
═
▌
φ
²
‫מ‬
₧
«
╛
╬
▐
ε
■
‫ן‬
ƒ
»
┐
╧
▀
∩
CP-863 (Canadian- French)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
Ç
É
¦
░
└
╨
α
≡
ü
È
í
▒
┴
╤
ß
±
é
Ê
‘
▓
┬
╥
Γ
≥
â
ô
ó
│
├
╙
π
≤
Â
Ë
ú
┤
─
╘
Σ
⌠
à
Ï
¨
╡
┼
╒
σ
⌡
¶
û
,
A0h
CP-862 (Hebrew)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
╢
╞
╓
µ
÷
ç
ù
¯
╖
╟
╫
τ
≈
ê
¤
Î
╕
╚
╪
Φ
°
ë
Ô
⌐
╣
╔
┘
Θ
·
è
Ü
¬
║
╩
┌
Ω
·
ï
¢
½
╗
╦
█
δ
√
î
£
¼
╝
╠
▄
∞
ⁿ
=
Ù
¾
╜
═
▌
φ
²
Ä
Û
«
╛
╬
▐
ε
■
§
ƒ
»
┐
╧
▀
∩
CP-865 (Nordic)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
Ç
É
á
░
└
╨
α
≡
ü
æ
í
▒
┴
╤
ß
±
é
Æ
ó
▓
┬
╥
Γ
≥
â
ô
ú
│
├
╙
π
≤
ä
ö
ñ
┤
─
╘
Σ
⌠
à
ò
Ñ
╡
┼
╒
σ
⌡
å
û
a
╢
╞
╓
μ
÷
ç
ù
o
╖
╟
╫
τ
≈
33
ê
ÿ
¿
╕
╚
╪
Φ
°
ë
Ö
®
╣
╔
┘
θ
•
è
Ü
¬
║
╩
┌
Ω
·
ï
ø
½
╗
╦
█
δ
√
î
£
¼
╝
╠
▄
∞
n
ì
Ø
¡
╜
═
▌
ø
²
Ä
Pt
«
╛
╬
▐
ε
■
Å
ƒ
¤
┐
╧
▀
∩
P07303 Series Customer Display User's Manual
9.2.13
80h
90h
A0h
B0h
C0h
D0h
E0h
F0h
9.2.14
80h
90h
A0h
B0h
C0h
D0h
E0h
F0h
9.2.15
80h
CP-866 (Cyrillic)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
А
Р
а
░
└
╨
р
Ё
Ђ Ѓ
ђ ‘
Ў
° ±
А Б
Р С
а б
р с
D0h
E0h
F0h
Г
У
г
│
├
╙
у
є
Д
Ф
д
┤
─
╘
ф
Ї
Е
Х
е
╡
┼
╒
х
ї
Ж
Ц
ж
╢
╞
╓
ц
Ў
З
Ч
з
╖
╟
╫
ч
ў
И
Ш
и
╕
╚
╪
ш
°
Й
Щ
й
╣
╔
┘
щ
·
К
Ъ
к
║
╩
┌
ъ
·
Л
Ы
л
╗
╦
█
ы
√
М
Ь
м
╝
╠
▄
ь
№
Н
Э
н
╜
═
▌
э
¤
О
Ю
о
╛
╬
▐
ю
■
П
Я
п
┐
╧
▀
я
‚
’
ў
І
В
Т
в
т
ѓ
“
Ј
і
Г
У
г
у
„
”
¤
ґ
Д
Ф
д
ф
…
•
Ґ
µ
Е
Х
е
х
†
–
¦
¶
Ж
Ц
ж
ц
‡
—
§
·
З
Ч
з
ч
€ ‰
™
Ё ©
ё №
И Й
Ш Щ
и й
ш щ
Љ
љ
Є
є
К
Ъ
к
ъ
‹
›
«
»
Л
Ы
л
ы
Њ
њ
¬
ј
М
Ь
м
ь
Ќ Ћ Џ
ќ ћ џ
® Ї
Ѕ ѕ ї
Н О П
Э Ю Я
н о п
э ю я
Windows-1252
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
€
A0h
C0h
В
Т
в
▓
┬
╥
т
Є
Windows-1251 (Cyrillic)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
90h
B0h
Б
С
б
▒
┴
╤
с
ё
°
À
Ð
à
ð
‘
¡
±
Á
Ñ
á
ñ
‚
’
¢
²
Â
Ò
â
ò
ƒ
“
£
³
Ã
Ó
ã
ó
„
”
¤
´
Ä
Ô
ä
ô
…
•
¥
µ
Å
Õ
å
õ
†
–
¦
¶
Æ
Ö
æ
ö
‡
—
§
·
Ç
×
ç
÷
34
ˆ
˜
¨
¸
È
Ø
è
ø
‰
™
©
¹
É
Ù
é
ù
Š ‹ Œ
š › œ
ª « ¬
º » ¼
Ê Ë Ì
Ú Û Ü
ê ë ì
ú û ü
Ž
ž
®
½ ¾
Í Î
Ý Þ
í î
ý þ
Ÿ
¯
¿
Ï
ß
ï
ÿ
P07303 Series Customer Display User's Manual
9.2.16
Windows-1253 (Greek)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
80h
90h
A0h
B0h
C0h
D0h
E0h
F0h
9.2.17
80h
90h
A0h
B0h
C0h
D0h
E0h
F0h
9.2.18
80h
90h
A0h
B0h
C0h
D0h
E0h
F0h
€
‚
‘ ’
΅ Ά
± ²
ΐ Α Β
Π Ρ
ΰ α β
π ρ ς
ƒ „ … †
“ ” • –
£ ¤ ¥ ¦
³ ´ µ ¶
Γ Δ Ε Ζ
Σ Τ Υ Φ
γ δ ε ζ
σ τ υ φ
‡
—
§
·
Η
Χ
η
χ
¨
Έ
Θ
Ψ
θ
ψ
‰
™
©
Ή
Ι
Ω
ι
ω
‹
›
«
Ί »
Κ Λ
Ϊ Ϋ
κ Λ
ϊ ϋ
¬
Ό
Μ
ά
μ
ό
–
½
Ν
έ
ν
ύ
®
Ύ
Ξ
ή
ξ
ώ
¯
Ώ
Ο
ί
ο
Windows-1255 (Hebrew)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
€
‚ ƒ „ … † ‡ ˆ
‘ ’ “ ” • – — ˜
¡ ¢ £ ₪ ¥ ¦ § ¨
° ± ² ³ ´ µ ¶ · ¸
ְ ֱ ֲ ֳ ִ ֵ ֶ ַ ָ
‫״ ׳ ײ ױ װ ׃ ׂ ׁ ׀‬
‫ט ח ז ו ה ד ג ב א‬
‫ר ק צ ץ פ ף ע ס נ‬
‰
™
©
¹
ֹ
,
‫י‬
‫ש‬
×
÷
:
‫ך‬
‫ת‬
‹
›
« ¬ –
» ¼ ½
ֻ ּ ֽ
; . !
‫ם ל כ‬
® ¯
¾ ¿
‫ֿ ־‬
?
‫ן מ‬
Windows-1257 (Baltic)
00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh
€
‚
‘ ’
¢
° ± ²
Ą Į Ā
Š Ń Ņ
ą į ā
š ń ņ
“
£
³
Ć
Ó
ć
ó
„
”
¤
´
Ä
Ō
ä
ō
… † ‡
• – —
¦ §
µ ¶ ·
Å Ę Ē
Õ Ö ×
å ę ē
õ ö ÷
35
Ø
ø
Č
Ų
č
ų
‰
™
©
¹
É
Ł
é
ł
‹
›
Ŗ «
ŗ »
Ź Ė
Ś Ū
ź ė
ś ū
¬
¼
Ģ
Ü
ģ
ü
¨
¯
–
½
Ķ
Ż
ķ
ż
ˇ
˛
®
¾
Ī
Ž
ī
ž
¸
Æ
æ
Ļ
ß
ļ
˙
P07303 Series Customer Display User's Manual
10.
Display Module Dimension
200mm
0.38o
176mm
39mm 70mm
158.6mm
5.25mm
0.85mm
0.25mm
1.05mm
0.25mm
9.0mm
9.5mm
1.5mm
22.5mm
1.5mm
1.5mm
6.65mm
36
B. 1 x 12 Customer Display
1. Checklist
G
501 mm
225 mm
191 mm
281 mm
93 mm
Pole Display Module
Flat Cable (DB-9P to DB-9P
flat cable connector)
Base Unit
Two pieces of pole support
(1x22cm, 1x9cm)
Installation guide
Power Adapter
2. Features
1.
2.
3.
4.
Data can be display on 12 columns x 1 line.
Blue–green color and large character are easy to see.
Command emulation modes include: POS7300, EPSON ESC/POS.
Provides an interface based in RS-232C, and RS232C baud rate 9600 bps.
P07303 Series Customer Display User's Manual
3. Specification
NO
Item
Description
1
Display method
Vacuum fluorescent display
2
Number of character
3
Character font
7 segment
4
Display color
Blue green
5
Brightness
700 cd /㎡
6
Character type
10 numeric
7
Character size
dot matrix 17.0 x 5.4 mm
8
Power supply
9
Power consumption
3-6W
10
MTBF
25000 hours (power on time)
11
Panel dimensions
224 (W) x 93 (H) x 50(D) mm
12
Support dimensions
13
Base dimensions
19.7 x 10 cm (W x D)
14
Viewing angle
-5 - 60 degrees
15
Rotation angle
Maximum 270 degrees
16
Weight
1.25 Kg
17
Operating temperature
5 - 45 oC
18
Operating Humidity
30%-85%
19
Storage Temperature
-10 – 55oC
20
Storage Humidity
10%-85%
40 characters
(12 columns x 1 lines)
11-19VDC
Manufacture offer +12V power adapter
Long support :
22 cm
Short support :
9 cm
38
P07303 Series Customer Display User's Manual
4. Interface
4.1.
Interface Specification
Data transmission
Serial
Synchronization
Asynchronous
Handshaking
DTR / DSR
MARK = -3 to –15 V (logic “1”)
Signal level
SPACE = +3 to +15 V (logic “0”)
4.2.
Baud rates
9600 bps
Parity
None
Bit length
8 bits
Stop bits
1 bit
Display Base
Below illustrate the configuration of Stand alone VFD Pole Display base.
Figure of VFD Pole Display Base
4.3.
Connector
PWR
COM
RJ45
39
P07303 Series Customer Display User's Manual
PWR: Power input connector from adapter
„ Connector type: DC jack (5.5/2.1)
„ Pin assignment
No
Signal
+
Vin
GND
RJ45: Connect to display panel
„ Connector type: Phone-jack 10P/8C
10
1
COM: RS232C link to PC/HOST connector (9-pin)
„ Connector type: D-sub 9 pin female
1
5
6
9
40
P07303 Series Customer Display User's Manual
5. Command List Table
Command List Table – 1
Command
ESC @
ESC D
ESC O m
Code (Hex)
1B 40
1B 44
1B 4F m
ESC B m
1B 42 m
ESC [ D
SO
NULL K
ESC [ C
SI
NULL M
ESC [ H
HOM
ESC [ L
CR
LF
NULL G
ESC [ R
NULL O
ESC [ K
ESC l x y
ESC P x y
1B 5B 44
0E
00 4B
1B 5B 43
0F
00 4D
1B 5B 48
0B
1B 5B 4C
0D
0A
00 47
1B 5B 52
00 4F
1B 5B 4B
1B 6C x y
1B 50 x y
CLR
CAN
.
0C
12
2E
ESC . x m
1B 2E x m
‘
27
ESC ‘ x m
1B 27 x m
Function Description
Initialize display
Enable the demo mode
Display ON or OFF
¾ m=1~2
Adjust the brightness level
¾ m=1~3
Move cursor left
Move cursor right
Move cursor to home position
Move cursor to left-most position
Move cursor to right-most position
Move cursor to bottom position
Move cursor to specified position
¾ x = 1 ~ 12
¾ y=1
Clear display screen
Clear cursor line
Set the pointer mark on the last show
character location
Set the pointer mark ON or OFF on
specified position
¾ x = 1 ~ 12
¾ m= 0 ~ 1
Set the comma mark on the last show
character location
Set the comma mark ON or OFF on
specified position
¾ x = 1 ~ 12
¾ m= 0 ~ 1
41
P07303 Series Customer Display User's Manual
Command List Table – 2
Command
Code (Hex)
Function Description
ESC Q A
1B 51 41 [DATA] 0D Set the string display
[DATA] CR
¾ Maximal [DATA] length is 12
ESC F A [DATA] 1B 46 41 [DATA] 0D
CR
ESC - m
1B 2D m
Set left-most dash ON or OFF
¾ m= 1 ~ 2
ESC _ n
1B 5F n
Set cursor ON or OFF
¾ n= 0 ~ 1
US E n
1F 45 n
Blink display screen
¾ n = 00h~FFh
„ n = 0 for disable blink
BS
08
Back space
42
P07303 Series Customer Display User's Manual
6. Command Details
Command Details – 1
„
„
„
„
„
„
„
„
ESC [ C
ASCII Format
Dec. Format
Hex. Format
Description
SI
ASCII Format
Dec. Format
Hex. Format
Description
ESC [ H
ASCII Format
Dec. Format
Hex. Format
Description
ESC [ L
ASCII Format
Dec. Format
Hex. Format
Description
CR
ASCII Format
Dec. Format
Hex. Format
Description
LF
ASCII Format
Dec. Format
Hex. Format
Description
ESC [ R
ASCII Format
Dec. Format
Hex. Format
Description
HOM
ASCII Format
Dec. Format
Hex. Format
Description
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
/ Move cursor right /
ESC [ C
[027] [091] [067]
[1Bh] [5Bh] [43h]
Move cursor one character to the right
/ Move cursor right /
SI
[015]
[0Fh]
Move cursor one character to the right
/ Move cursor to home position /
ESC [ H
[027] [091] [072]
[1Bh] [5Bh] [48h]
Move cursor to the left-most position
/ Move cursor to left-most position /
ESC [ L
[027] [091] [076]
[1Bh] [5Bh] [4Ch]
Move cursor to the left-most position
/ Move cursor to left-most position /
CR
[013]
[0Dh]
Move cursor to the left-most position
/ Move cursor to left-most position /
LF
[010]
[0Ah]
Move cursor to the left-most position
/ Move cursor to right-most position /
ESC [ R
[027] [091] [082]
[1Bh] [5Bh] [52h]
Move cursor to the right-most position
/ Move cursor to home position /
HOM
[011]
[0Bh]
Move cursor to the home position
43
P07303 Series Customer Display User's Manual
Command Details – 2
„
„
„
„
„
„
„
„
ESC [ K
ASCII Format
Dec. Format
Hex. Format
Description
ESC l x y
ASCII Format
Dec. Format
Hex. Format
Description
:
:
:
:
ESC P x y
ASCII Format
Dec. Format
Hex. Format
Description
:
:
:
:
CLR
ASCII Format
Dec. Format
Hex. Format
Description
CAN
ASCII Format
Dec. Format
Hex. Format
Description
.
ASCII Format
Dec. Format
Hex. Format
Description
ESC @
ASCII Format
Dec. Format
Hex. Format
Description
ESC D
ASCII Format
Dec. Format
Hex. Format
Description
:
:
:
:
:
:
:
:
:
:
:
:
/ Move cursor to bottom position /
ESC [ R
[027] [091] [075]
[1Bh] [5Bh] [4Bh]
Move cursor to the right-most position
/ Move cursor to specified position /
ESC l x y
[027] [108] [x] [y]
[1Bh] [6Ch] [x] [y]
Move cursor to the x’th column on the y’th line.
¾ x = 1 ~ 12
¾ y=1
/ Move cursor to specified position /
ESC P x y
[027] [80] [x] [y]
[1Bh] [50h] [x] [y]
Move cursor to the x’th column on the y’th line.
¾ x = 1 ~ 12
¾ y=1
/ Clear display screen /
CLR
[012]
[0Ch]
Clear all of the displayed characters
/ Clear cursor line /
CAN
[018]
[12h]
Clear the line containing the display
/ Set the pointer mark on last show character location /
:
:
:
:
:
:
:
:
:
:
:
:
.
[046]
[2Eh]
Set the pointer mark on last show character location.
/ Initialize display /
ESC @
[027] [064]
[1Bh] [40h]
Clear the data in the input buffer and setting.
/ Enable the demo mode /
ESC D
[027] [068]
[1Bh] [44h]
Enable the demo mode. Send any word can exit the
demo mode.
44
P07303 Series Customer Display User's Manual
Command Details – 3
„
„
„
„
„
„
ESC O m
ASCII Format
Dec. Format
Hex. Format
Description
:
:
:
:
ESC B m
ASCII Format
Dec. Format
Hex. Format
Description
:
:
:
:
ESC [ D
ASCII Format
Dec. Format
Hex. Format
Description
SO
ASCII Format
Dec. Format
Hex. Format
Description
ESC . x m
ASCII Format
Dec. Format
Hex. Format
Description
:
:
:
:
:
:
:
:
/ Display ON or OFF /
ESC O m
[027] [079] [m]
[1Bh] [4Fh] [m]
Clear the data in the input buffer and setting.
¾ m=1 ~ 2
„ m=1: Display ON (Default)
„ m=2: Display OFF
/ Adjust the brightness level /
ESC B m
[027] [066] [m]
[1Bh] [42h] [m]
Adjust the brightness level
¾ m=1 ~ 3
„ m=1: low level
„ m=2: middle level
„ m=3: high level (Default)
/ Move cursor left /
ESC [ D
[027] [091] [068]
[1Bh] [5Bh] [44h]
Move cursor one character to the left
/ Move cursor left /
SO
[014]
[0Eh]
Move cursor one character to the left
/ Set the pointer mark ON or OFF on specified position /
:
:
:
:
‘
ESC . x m
[027] [046] [x] [m]
[1Bh] [2Eh] [x] [m]
Set the pointer mark ON or OFF at x position.
¾ x = 1 ~ 12
¾ m= 0 ~ 1
„ m=0: Clear the pointer mark at x position
„ m=1: Set the pointer mark at x position
/ Set the comma mark on last show character location /
ASCII Format
Dec. Format
Hex. Format
Description
:
:
:
:
‘
[039]
[27h]
Set the comma mark on last show character location.
45
P07303 Series Customer Display User's Manual
Command Details – 4
„
ESC ‘ x m
ASCII Format
Dec. Format
Hex. Format
Description
/ Set the comma mark ON or OFF on specified position /
:
:
:
:
„
ESC Q A [DATA] CR
ASCII Format
:
Dec. Format
:
Hex. Format
:
Description
:
„
ESC F A [DATA] CR
ASCII Format
:
Dec. Format
:
Hex. Format
:
Description
:
„
ESC - m
ASCII Format
Dec. Format
Hex. Format
Description
:
:
:
:
ESC _ n
ASCII Format
Dec. Format
Hex. Format
Description
:
:
:
:
„
ESC ‘ x m
[027] [039] [x] [m]
[1Bh] [27h] [x] [m]
Set the pointer mark ON or OFF at x position.
¾ x = 1 ~ 12
¾ m= 0 ~ 1
„ m=0: Clear the comma mark at x position
„ m=1: Set the comma mark at x position
/ Set the string display /
ESC Q A [DATA] CR
[027] [081] [065] [DATA] [013]
[1Bh] [51h] [41h] [DATA] [0Dh]
Set the string display mode.
The string display mode will be cancel with CLR or CAN.
¾ Maximal [DATA] length is 12
/ Set the string display /
ESC F A [DATA] CR
[027] [070] [065] [DATA] [013]
[1Bh] [46h] [41h] [DATA] [0Dh]
Set the string display mode.
The string display mode will be cancel with CLR or CAN.
¾ Maximal [DATA] length is 12
/ Set left-most dash ON or OFF /
ESC – m
[027] [045] [m]
[1Bh] [2Dh] [m]
Set left-most dash on/off.
¾ m= 1 ~ 2
„ m=1: Display
„ m=2: No display (Default)
/ Set cursor ON or OFF /
ESC _ n
[027] [095] [n]
[1Bh] [5Fh] [n]
Set cursor on/off.
¾ n=0 ~ 1
„ n=0: Display
„ n=1: No display (Default)
46
P07303 Series Customer Display User's Manual
Command Details – 5
„
US E n
ASCII Format
Dec. Format
Hex. Format
Description
„
BS
ASCII Format
Dec. Format
Hex. Format
Description
NULL K
ASCII Format
Dec. Format
Hex. Format
Description
NULL M
ASCII Format
Dec. Format
Hex. Format
Description
NULL G
ASCII Format
Dec. Format
Hex. Format
Description
NULL O
ASCII Format
Dec. Format
Hex. Format
Description
STX 05 V 01
ASCII Format
Dec. Format
Hex. Format
Description
„
„
„
„
„
/ Blink display screen /
: US _ n
: [031] [069] [n]
: [1Fh] [45h] [n]
: Blink display screen
¾ n=00h~FFh
„ n=0 for no blink
/ Back space /
: BS
: [08]
: [08h]
: Move cursor left and clean the character.
/ Move cursor left /
: NULL K
: [00] [075]
: [00h] [4Bh]
: Move cursor left
/ Move cursor right /
: NULL M
: [00] [077]
: [00h] [4Dh]
: Move cursor right
/ Move cursor to left-most position /
: NULL G
: [00] [071]
: [00h] [47h]
: Move cursor to left-most position
/ Move cursor to right-most position /
: NULL O
: [00] [079]
: [00h] [4Fh]
: Move cursor to right-most position
TEX / Show firmware version /
: NULL O
: [02] [05] [86] [01] [03]
: [02h] [05h] [56h] [01h] [03h]
: Show the firmware version on the screen
47
P07303 Series Customer Display User's Manual
7. Character Set
0
1
2
3
4
5
6
7
8
9
A/a
B/b
C/c
D/d
E/e
F/f
G/g
H/h
I/i
J/j
K/k
L/l
M/m
N/n
O/o
P/p
Q/q
R/r
S/s
T/t
U/u
V/v
W/w
X/x
Y/y
Z/z
Space
-
=
/
[
]
_
Note:
¾
Undefined characters will be displayed as a space character.
48
P07303 Series Customer Display User's Manual
8. Display Module Dimension
49
(2 x 20 Customer Display and 1 x 12 Customer Display)
Appendix A - Command Details
A.1. Overwrite mode
In this mode, the cursor will move towards the right and begin from the upper left
position. When the cursor has reached the end of the upper line, the cursor will
move down to the bottom left position to continue. When the cursor has reached
the end of the bottom line, it will move to up the upper left position and overwrite
the previous characters.
A.2. Vertical scroll mode
In this mode, the cursor will move towards the right. The cursor will begin from the
upper left position until it has reached the end of the upper line. The cursor will
then move down to the bottom left position to continue until it has reached the end
of the bottom line.
A.3. Horizontal scroll mode
In this mode, the extent of the cursor activity is bound by a predefined range,
limited to the upper line. (Please refer to Set or cancel window command), where
the default window is the whole upper line. The cursor will begin from the left-end
of the range and move rightward until it reached the end of the range, to continue,
the characters that comes thereafter will start pushing the previous characters
leftward from the right-end, scrolling the characters to the left.
A.4. Set the string display mode and write string to display
Set the string display mode, write to upper or lower line d1 d2 d3 … dn {1≦n≦
20}. ‘A’ stands for the upper line, ‘B’ stands for the lower line. The string display
mode will be cancelled and the display will return to the previous mode after
receiving CLR or CAN.
A.5. Upper line message continuous scroll
The message (previously defined) will scroll continuously in the horizontal direction
until a new command is received.
A.6. Move cursor left
When the current cursor is at the left-end position, this command operates
differently depending on the display mode.
„ Overwrite mode: When the cursor reached the left-end of the lower line, it will
continue to the right-end of the upper line, overwrite previous characters.
When it reached the left end of the upper line, it will continue to the right-end
of the lower line.
„ Vertical scroll mode: When the cursor reached the left-end of the lower line,
the lower line will scroll up and replace the previous upper line, the lower line
will be cleared and the cursor will continue to the right end of the lower line.
„ Horizontal scroll mode: The cursor will remain stationary.
A.7. Move cursor right
P07303 Series Customer Display User's Manual
Move the cursor to the right. When the cursor has reached the right-end, this
command operates differently depending on the display mode.
„ Overwrite mode: When the cursor has reached the right-end of the lower line,
it will continue to the left-end of the upper line and overwrite previous
characters. When it has reached the right-end of the upper line, it will continue
to the right-end of the lower line.
„ Vertical scroll mode: When the cursor has reached the right-end of the lower
line, the lower line will scroll up to replace the upper line, the lower line is
cleared and ready to continue characters thereafter.
„ Horizontal scroll mode: The cursor will remain stationary.
A.8. Move cursor up
Move the cursor up one line. When the cursor is on the upper line, this command
operates differently depending on the display mode.
„ Overwrite mode: The cursor is moved to the same column the lower line.
„ Vertical scroll mode: The characters displayed on the upper line is scrolled
to the lower line, and the upper line is cleared. The cursor will remain at the
same position.
„ Horizontal scroll mode: The cursor will remain stationary.
A.9. Move cursor down
Move the cursor down one line. When the cursor is on the lower line, this
command operates differently depending on the display mode.
„ Overwrite mode: The cursor is moved to the same column on the upper line.
„ Vertical scroll mode: The characters displayed on the lower line are scrolled
to the upper line, and the lower line is cleared. The cursor will remain at the
same position.
„ Horizontal scroll mode: The cursor will remain stationary.
A.10. Move cursor to home position
The cursor will move to the left-end position of the upper line.
A.11. Move cursor to left-most position
The cursor will be moved to the left-end position of the current line.
A.12. Move cursor to right-most position
The cursor will be moved to the right-end position of the current line.
A.13. Move cursor to bottom position
The cursor will be moved to the right-end position on the lower line.
51
P07303 Series Customer Display User's Manual
A.14. Move cursor to specified position
The cursor will be moved to column x on line y.
A.15. Initialize display
The data in the input buffer will be cleared and reset from default.
A.16. Reset the window
Reset the window on the display.
When s=0, the window is cancelled (values: x1, x2, and y are not required.)
When s=1, the window will be reset (values: x1, x2, and y are required.)
The x1 and x2 set the position of the left column and right column, respectively, of
the window.
The y sets the upper line or the lower line of the window.
This function is valid within the horizontal mode.
A.17. Clear display screen and clear string mode
All the display characters will be cleared, and the string mode will be cancelled.
A.18. Clear current line and cancel string mode
The current line is cleared, and the string mode is cancelled.
A.19. Brightness adjustment
Adjust the brightness of the vacuum fluorescent display.
When n=3, brightness=70%
When n=4, brightness=100%
A.20. Set cursor ON or OFF
When n=0, cursor is OFF
When n=1, cursor is ON
52
P07303 Series Customer Display User's Manual
Appendix B - Control Code Set
HEX
00H
01H
02H
03H
04H
05H
06H
07H
08H
09H
0AH
0BH
0CH
0DH
0EH
0FH
CODE
NULL
SOH, MD1
STX, MD2
ETX, MD3
EOT, MD4
ENQ, MD5
ACK, MD6
BEL, MD7
BS, MD8
HT
LF
VT, HOM
FF, CLR
CR
SO, SLE1
SI, SLE2
HEX
10H
11H
12H
13H
14H
15H
16H
17H
18H
19H
1AH
1BH
1CH
1DH
1EH
1FH
53
CODE
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS, SF1
US, SF2