Antik Juice Encoder EN 5008 Specifications

DIRECTORY
Chapter 1 Product Introduction ............................................................................................................. 1
1.1 Outline ................................................................................................................................................ 1
1.2 Main Features ................................................................................................................................... 1
1.3 Specifications .................................................................................................................................... 1
1.4 Principle Chart................................................................................................................................... 3
1.5 Appearance and Illustration ............................................................................................................ 3
Chapter 2 Installation Guide .................................................................................................................. 5
2.1 Acquisition Check ............................................................................................................................. 5
2.2 Installation Preparation .................................................................................................................... 5
2.3 Wire’s Connection ............................................................................................................................ 7
2.4 Signal Cable Connection ................................................................................................................. 7
Chapter 3 Operation ............................................................................................................................. 11
3.1 Initializing ......................................................................................................................................... 11
3.2 General Setting ............................................................................................................................... 11
Chapter 4 SNMP Operation ................................................................................................................. 21
4.1 Installation ........................................................................................................................................ 21
4.2 Software Operation ........................................................................................................................ 21
4.3 EN 5008 8 in 1 MPEG-4 AVC/ H.264 HD Encoder Operation ................................................. 26
4.4 Other Settings ................................................................................................................................. 36
Chapter 5 Troubleshooting .................................................................................................................. 40
Chapter 6 Packing list........................................................................................................................... 41
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Chapter 1 Product Introduction
1.1 Outline
The ANTIK Juice Encoder EN 5008 8-in-1 MPEG-4 AVC/H.264 HD encoder is our
newest professional HD audio & video encoding and multiplexing device with powerful
functionality. It is equipped with 8 HDMI channels input supporting MPEG -4 AVC/H.264
High Profile code format & main Profile code format and 1 ASI input. It can multiplex the
ASI input TS and the 8 encoded SPTS to generate a MPTS output with the inserted PSI/SI
information. In conclusion, its high integration and cost-effective design make this device
widely used in variety of digital distribution systems such as CATV digital head-end,
satellite and terrestrial digital TV, etc.
1.2 Main Features
 Support 8 HDMI channels input & 1 ASI Input
 Support H.264/AVC high profile level 4.0 video encoding
 Support MPEG1 Layer 2 (HE-AAC (V2) or LC-AAC optional) audio encoding
 Support PSI/SI editing and inserting
 Support VBR or CBR video bitrate mode
 Support 720P, 1080I, 1080P HD video format
 Support ASI output MPTS or 8 SPTS
 Support IP Output MPTS and 8 SPTS
 Support IP null packet filter
 Support PID filter and transparent transport
 Real-time output bit-rate monitoring
 Update device through NMS port
 Support LCD / keyboard operating, and network management (SNMP)
1.3 Specifications
1 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Input
8 HDMI inputs
1 ASI input, BNC interface
1920×1080_60P, 1920×1080_50P
1920×1080_60i, 1920×1080_50i
Resolution
1280×720_60P, 1280×720 _50P
720x576_50i, 720x480_59.95i
Video
Audio
Encoding
MPEG-4 AVC/H.264 high profile level 4.0
Bit-rate
0.8Mbps~19Mbps (each channel)
Rate Control
CBR/VBR
GOP Structure
IBBP
Advanced
Pretreatment
De-interlacing, Noise Reduction, Sharpening
Encoding
MPEG-1 Layer II, HE-AAC (V2), LC-AAC
Sampling rate
48KHz
Resolution
24 bit
Bit-rate
64Kbps~384Kbps each channel
1 ASI input multiplexed with local 8 channels of TS
Multiplexing
2*ASI output, BNC interface
Stream output
MPTS and 8 SPTS over UDP, 1000 Base-T Ethernet
interface (UDP unicast / multicast)
LCD/keyboard operating, NMS supporting
Chinese-English control interface
System function
Ethernet software & hardware upgrade
Dimension (W× L× H)
Approx weight
Miscellaneous
440mm×410mm×44.5mm
4kg
Temperature
0~45℃(work),
Power
-20~80℃(Storage)
AC 100V-220V±10%, 50/60Hz
Consumption
25W
2 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
1.4 Principle Chart
1.5 Appearance and Illustration
Front Panel Illustration:
1
2
3
4 5 6
Indicate area: All indicators will light on when the device is on the current working state.
1
LCD Screen
Power Indicator
2
Indicators
TS In: Input Lock Indicator
CH1-CH8: When the program has been multiplexed, the
indicator will be on.
3
UP/ DOWN, LEFT/RIGHT Keys
4
Enter Key
5
Menu Key
6
Lock Key
3 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Rear Panel Illustration:
1
2
1
8 * HDMI Input Ports
2
ASI Input Port
3
2 * ASI Output Ports
4
Data Port (for IP Signal Output)
5
NMS (Network Management Port)
6
Power Switch and socket
7
Grounding Pole
4 / 43
Antik Technology / www.antiktech.com
3
4 5
6
7
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Chapter 2 Installation Guide
2.1 Acquisition Check
When users open the package of the device, it is necessary to check items according to packing
list. Normally it should include the following items:

EN 5008 8 in 1 MPEG-4 AVC/H.264 HD Encoder

User’s Manual

HDMI Cable

ASI Cable

Power Cord
If any item is missing or mismatching with the list above, please contact local dealer.
2.2 Installation Preparation
When users install device, please follow the below steps. The details of installation will be
described at the rest part of this chapter. Users can also refer rear panel chart during the
installation.
The main content of this chapter including:

Checking the possible device missing or damage during the transportation

Preparing relevant environment for installation

Installing Encoder

Connecting signal cables

Connecting communication port (if it is necessary)
2.2.1 Device’s Installation Flow Chart is Illustrated as following:
Acquisition
Check
Fixing
Device
Connecting
Grouding
Wire and
Power
Cord
Connecting
Signal Wire
2.2.2 Environment Requirement
5 / 43
Antik Technology / www.antiktech.com
Setting
Parameter
Running
Device
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Item
Requirement
Machine Hall Space
When user installs machine frame array in one machine hall, the
distance between 2 rows of machine frames should be 1.2~1.5m
and the distance against wall should be no less than 0.8m.
Electric Isolation, Dust Free
Machine Hall Floor
Volume
resistivity
of
ground
anti-static
material:
7
10
1X10 ~1X10 ,Grounding current limiting resistance: 1M
(Floor bearing should be greater than 450Kg/㎡)
Environment
Temperature
5~40℃(sustainable ),0~45℃(short time),
Relative Temperature
20%~80% sustainable
Pressure
86~105KPa
Door & Window
Installing rubber strip for sealing door-gaps and dual level
glasses for window
Wall
It can be covered with wallpaper, or brightness less paint.
Fire Protection
Fire alarm system and extinguisher
Power
Requiring device power, air-conditioning power and lighting
power are independent to each other. Device power requires AC
power 220V 50Hz. Please carefully check before running.
installing air-conditioning is recommended
10%~90% short time
2.2.3 Grounding Requirement

All function modules’ good grounding designs are the basis of reliability and stability of
devices. Also, they are the most important guarantee of lightning arresting and interference
rejection. Therefore, the system must follow this rule.

Coaxial cable’s outer conductor and isolation layer should keep proper electric conducting
with the metal housing of device.

Grounding conductor must adopt copper conductor in order to reduce high frequency
impedance, and the grounding wire must be as thick and short as possible.

Users should make sure the 2 ends of grounding wire well electric conducted and be
antirust.

It is prohibited to use any other device as part of grounding electric circuit

The area of the conduction between grounding wire and device’s frame should be no less
than 25mm2.
6 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
2.2.4 Frame Grounding
All the machine frames should be connected with protective copper strip. The grounding wire
should be as short as possible and avoid circling. The area of the conduction between
grounding wire and grounding strip should be no less than 25mm2.
2.2.5 Device Grounding
Connecting the device’s grounding rod to frame’s grounding pole with copper wire.
2.3 Wire’s Connection
The grounding wire conductive screw is located at the right end of rear panel, and the power
switch, fuse, power supply socket is just beside ,whose order goes like this, power switch is on
the left ,power supply socket is on the right and the fuse is just between them.

Connecting Power Cord
User can insert one end into power supply socket, while insert the other end to AC power.

Connecting Grounding Wire
When the device solely connects to protective ground, it should adopt independent way,
say, share the same ground with other devices. When the device adopts united way, the
grounding resistance should be smaller than 1Ω.
Caution:
Before connecting power cord to EN 5008 8 in 1 MPEG-4 AVC/H.264 HD Encoder,
user should set the power switch to “OFF”.
2.4 Signal Cable Connection
The signal connections include the connection of input signal cable and the connection of
output signal cable. The details are as follows:
2.4.1 HDMI input cable illustration:
7 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
2.4.2 ASI output cable illustration:
2.4.3 Network Cable illustration (CAT5):
2.4.4 HDMI input interface connection
User can firstly find the HDMI interface on the device according to the connector mark
described on the rear panel illustration, and then connect the HDMI cable (in the accessories).
One end is connected to the head-end equipment while the other end to the encoder’s HDMI
input port. The encoder’s HDMI input port (HDMI1…HDMI8) and its connection are
illustrated as follows:
2.4.5 ASI output interface connection
User can firstly find the ASI output interface on the device according to the connector mark
described on the rear panel illustration, and then connect the ASI cable (in the accessories). One
8 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
end is connected to the encoder’s ASI out connector (ASI1, ASI2) while the other end to the TS
stream multiplexer or modulator’s ASI input port. The encoder’s ASI output interface and its
connection are illustrated as follow:
2.4.6 IP Output Interface connection
Users can firstly find the DATA interface on the device according to the connector mark
described on the rear panel illustration, and then connect the network (CAT5). One end of the
network cable is connected to the encoder’s DATA output connector, while the other end to the
TS stream multiplexer IP input port or other device which can input IP signal. The encoder’s
DATA connection is illustrated as follows:
2.4.7 NMS Connection
Users can firstly find the NMS interface on the device according to the connector mark
described on the rear panel illustration, and then connect the network (CAT5). One end of the
network cable is connected to the encoder’s NMS connecter, while the other end to the
computer or the PC. The encoder’s NMS connection is illustrated as follows:
9 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
10 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Chapter 3 Operation
EN 5008 8 in 1 MPEG-4 AVC/H.264 HD Encoder’s front panel is user operating interface.
Before operating, user can decide whether directly use the default setting or customize the input
and output parameters setting. The detail operations go as follows:
Keyboard Function Description:
ENTER: Activating the parameters which need modifications, or confirming the change after
modification.
MENU: To cancel presently entered value, resume previous setting and return to previous
menu.
LEFT/RIGHT: To move the “►” to choose or set the parameters.
UP/DOWN: To modify activated parameter or page up/down when parameter is inactivated.
LOCK: To Lock the screen / cancel the lock state. After pressing lock key, the system will
question the users to save present setting or not. If not, the LCD will display the current
configuration state.
At the “Factory Configuration” page, user can press “ENTER” key to restore the factory
default configuration.
3.1 Initializing
After powering on the device,it will take a few seconds to initialize the system, and then the
LCD will show the device name and output real-time bit-rate in the first row, while the 8
channels’ respective input video resolution, frame rate and real-time encoding bit-rate in the
second row in turn. It shows as below:
8 in 1 Encoder
1 480I 60
08.235M
65.958 Mbps
2 480I 60 08.241M
3.2 General Setting
By pressing LOCK key, users can enter in the main menu and set the input and output
11 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
parameters in the following editing interfaces, the LCD will display the following pages:
►1 Input Setting
3 Output Setting
2 ASI Setting
4 Network Setting
►5 Saving Config
7 Version (SNMP)
6 Loading Config
8 Language
The option with “►” is the current selection, users can press the ENTER key to enter the
specified submenu to modify the device parameter.
3.2.1 Input Setting
Under this menu, users can enter the corresponding encoding channel to set the relevant audio
and video input parameters, and select programs to multiplex. The LCD will display 8
submenus which from Encoding Channel 1 to Encoding Channel 8. The setting principle is the
same for Encoding Channel 1-8, so here this manual just takes one channel as the example to
explain. After pressing the enter key, the LCD will display the following pages:
►1.1 Encoder 1
1.3 Encoder 3
1.2 Encoder 2
1.4 Encoder 4
►1.5 Encoder 5
1.7 Encoder 7
1.6 Encoder 6
1.8 Encoder 8
After users enter the submenu, the interface will turn into the following pages, and then users
can enter the corresponding interface to modify the parameters.
►1.1.1 Video
1.1.3 System
1.1.2 Audio
1.1.4 PG Muxer
3.2.1.1 Video Setting
►1.1.1.1 Bitrate
1.1.1.3 Profile
1.1.1.2 BitrateMod
1.1.1.4 Level
 Bitrate
12 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
By press “Enter” key, user can modify relevant parameter of encoding rate (adjustable range:
0.8M~19M), the specific steps are displayed as follows:
1.1.1.1 Bitrate
8.000Mbps
 Bitrate Mode
User can choose CBR & VBR at this menu. CBR (Constant Bit-rate) means that the bit-rate
will be a constant value. VBR (Variable Bit-rate) means that the bit-rate will always change
along with the video scene changing.
1.1.1.2 BitrateMod
[CBR]
01/01
VBR
 Profile
User can select the configuration of H.264 profile at this menu. There are H.264 High Profile
code format and main Profile code format.
1.1.1.3 Profile
[HIGH]
01/01
MAIN
 Level
User can select the H.264 level at this menu. The option with bracket is the current choice.
1.1.1.4 Level
[1.2]
1.1.1.4 Level
[2.2]
1.1.1.4 Level
[4.0]
01/03
1.3
2.0
2.1
02/03
3.0
3.1
3.2
03/03
4.1
4.2
3.2.1.2 Audio Setting
13 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
1.1.2.1 Bit Rate
1.1.2.2 Format
 Audio Bit Rate Setting
User can set the input audio bit-rate by pressing the enter key to enter the main editing interface.
And there are: 64Kbps, 96Kbps, 112Kbps, 128Kbps, 160Kbps, 192Kbps, 224Kbps, 256 Kbps,
320Kbps, and 384Kbps. After the modification, users can press enter key again to take the
modification into effect. The LCD will display the following pages:
1.1.2.1 Bit-rate
64 Kbps
96Kbps
1.1.2.1 Bit-rate
160 Kbps
192Kbps
112Kbps
224Kbps
1.1.2.1 Bit-rate
320 Kbps
384Kbps
01/03
[128Kbps]
02/03
[256Kbps]
03/03
 Audio Format Setting
AAC: Advanced Audio Coding
Users can set the input audio format in this interface, and the 3 options are MPEG1 Layer Ⅱ,
LC-AAC, and HE-AAC. When users enter the main editing menu, the LCD will display the
following page:
1.1.2.2 Format
[MPEG1-Layer Ⅱ]
01/02
LC-AAC
1.1.2.2 Format
[HE-AAC]
02/02
3.2.1.3 System Settings
►1.1.3.1 Prog Number
1.1.3.3 Audio PID
1.1.3.2 Video PID
1.1.3.4 PMT PID
14 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
►1.1.3.5 PCR PID
1.1.3.7 Out Address
1.1.3.6 IP Enable
1.1.3.8 Out Port
►1.1.3.9 Null PKT
Under this interface, users can set the corresponding system parameters, after the modification,
users can press enter key to take the modification into effect.
 Program Number Setting
Users can set the program number by pressing ENTER to enter this submenu. The LCD will
display as below:
1.1.3.1 Program Number
0x0101
 Video/Audio/PMT/PCR PID Settings
Users can set these parameters by pressing ENTER to enter these submenus. The LCD will
display the following pages, and the maximum PID number cannot exceed 0x1fff.
1.1.3.2 Video PID
0x0101
1.1.3.3 Audio PID
0x0102
1.1.3.4 PMT PID
0x0100
1.1.3.5 PCR PID
0x0101
 IP Enable
1.1.3.6 IP Enable
YES
01/01
[NO]
15 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
 Out Address/Out Port Setting
User can modify the out address and out port in below interfaces.
1.1.3.7 Out Address
224.002.002.002
1.1.3.8 Out Port
1002
 Null Packet
1.1.3.9 Null Packet
YES
01/01
[NO]
Users can choose YES (filter the null packet) or NO (don’t filter null packet) to decide whether
to filter the null packet or not.
3.2.1.4 Program Mux Setting
Users can decide whether to open the multiplexing function of the device.
 Channel Mux
Under this interface, users can decide whether to multiplex the channel encoding stream. YES
means that the device multiplexes the encoding stream into the MPTS, while NO means that the
output program is SPTS. The LCD will display the following pages after pressing enter key.
1.1.4.1 Channel Mux
[ YES]
01/01
NO
3.2.2 ASI Setting
Users can check the ASI input program amount in this interface, and the LCD will display the
following page. Prog: 006 represents the input program is 6 and Out:003 represents 3 of the 6
programs have been multiplexed.
16 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
► 2.1 Parse ASI Prog
2.1 Parse ASI Prog
► 001 HK1
√
Prog: 006 Out: 003
002 HK2
X
3.2.3 Output Setting
By press the enter key in the main editing interface, use can set the device output parameter.
The device will display the following page after users pressing the enter key.
► 3.1 IP Out Enable
3.2 IP Out Address
3.3 IP Out Port
3.4 Trans Stream ID
► 3.5 Output Stream
3.6 ASI Output
3.7 UTC Time Config
3.8 Null PKT
► 3.9 TS Package Num
3.2.3.1 IP Out Enable
This is the new function of this encoder, user can decide whether to open the IP output function
by press the ENTER key in this menu, and the operating interface will show the following
page:
► 3.1 IP out Enable
[ YES]
NO
3.2.3.2 IP Out Address
If users enable the IP output function, then users can set the device IP output address in this
interface. After users press the ENTER key, the operating interface will display the following
page:
► 3.2 IP Out Address
224.002.002.002
17 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
3.2.3.3 IP Out Port
In this menu, users can set the encoder IP output port number by press the ENTER key to enter
the main editing interface.
► 3.3 IP Out Port
01001
3.2.3.4 Trans Stream ID
Users can set the device TS ID in this interface after pressing the ENTER key to enter the main
editing page.
► 3.4 Trans Stream ID
00000
3.2.3.5 Output Stream
Users can modify the bit rate of output stream in this interface after pressing the ENTER key to
enter the main editing page.
3.5 Output Stream
040.000 Mbps
3.2.3.6 ASI Output
Users can set the ASI output in this interface under this menu, and there are 9 options: MPTS,
Channel 1-8.
3.6 ASI Output
[MPTS]
01/03
Channel 1
Channel 2
Channel 3
3.2.3.7 UTC Time
UTC refers to Universal Time Coordinated. User can enter this menu to set the time as needed
and it will then generate the TDT table and show in the user’s STB.
3.7 UTC Time Configuration
2012-01-29 15:45:03
18 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
3.2.3.8 Null Packet
3.8 Null Packet
01/01
YES
[NO]
3.2.3.9 TS Package Num
User can set the amount of TS packages by entering into below interface.
3.9 TS Package Num
1
2
3.9 TS Package Num
[5]
6
01/02
3
[4]
02/02
7
3.2.4 Network Setting
Users can set the network parameters by pressing the enter key, and the LCD will display the
following interfaces.
4.1 IP Address
192.168.005.018
4. 2 Subnet Mask
255.255.255.000
4.3 Gateway
192.168.002.001
4.4 Console Address
192.168.002.211
The MAC address is read-only in the keyboard operation interface, so users can just check the
physical address under this interface, and the modification must be done in the network
19 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
updating tools.
4.5 MAC Address
201012345679
NOTE: The MAC address is unique, and cannot be modified. When the MAC
address is ffffffffffff, users must modify the address through special software,
otherwise, the IP output data will be filter out when the IP stream passes through
the router.
3.2.5 Saving Configuration
Users can save the modification by pressing the enter key, and it will display the following
interface when user press the enter key.
5 Saving Config
YES
[NO]
01/01
3.2.6 Loading Configuration
In this interface, users can select the modified configuration and the factory defaulted
configuration. Users can enter the corresponding menu to select the configuration. The LCD
will display the following interfaces:
►6.1 Load Saved
6.2 Load Default
3.2.7 Version
Users can check the device software version and hardware version, and the LCD will display
the following interface when users press the ENTER key.
8 in 1
Encoder
SW 0.17F
HW 08
3.2.8 Language
User can select the needed language under this submenu:
8 Language
中文
20 / 43
Antik Technology / www.antiktech.com
[ENGLISH]
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Chapter 4 SNMP Operation
Network Management System
SNMP Network management system is applied to digital TV equipment operation, control and
management and parameters setting, etc. It centralizes digital TV equipment through network.
4.1 Installation
The software doesn’t need special installation. User can just open the folder SnmpNMS x.xy.z
to find the icon
and double click it to pop up the login interface.
4.2 Software Operation
4.2.1 Login Interface
A login interface will pop up firstly when the software is running and give user prompts to
input user name and password (The default user name is admin and no password. User can add
users and passwords as needed. Details please refer to 4.4.3 in 4.4 Other Settings.). The menu
shows as follows:
User can login the NMS by pressing OK key after inputting user name. Upon the inputs, the
software will verify them with database record automatically and the main interface will
appear.
4.2.2 Main Interface
21 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
User can create a device node tree in the left column by adding, modifying and deleting the
device node. This software provides a powerful node operation function, and the user can edit
various parameters in the device tree for management and classification.
4.2.3 Adding Frequency Point
The Add Freq Point dialog box popes up when the user clicks the Add Freq Point item in the
22 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Edit pull down menu on the menu row. The device will confirm the given frequency while user
clicks OK.
User can also click right mouse key to pop up the short-cut menu in device tree or in the left
blank column, then the corresponding dialog box will pop up by choosing Add Main Freq
Point. The device will confirm the given frequency while user clicks OK.
4.2.4 Adding Equipment under Given Frequency Point
User should choose the frequency point in advance, and then the dialog box of Add Equipment
will pop up when user clicks “Add Equipment” item in the Edit pull down menu on the menu
row.
4.2.5 Edit Equipment Interface
23 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
User should follow the steps as below:

Inputting the device IP Address

Inputting the port

Inputting the Equipment Name

Choosing the connected equipment type in drop down list of “Equipment Type” by
clicking the “▼” Or Click “?” to auto search the type of device.
NOTE:
1. The default IP of EN 5008 Encoder is 192.168.0.136, also you can check its IP address in
the front panel of device in case the IP changed unexpected.
2. The PC IP address and device IP address should be in the same network. For example the
Device IP is 192.168.2.136, sub mask is 255.255.255.0. So the PC IP address should be
192.168.2.X (1<X<255), sub mask is 255.255.255.0. User can use ping command to
confirm these two are in same network or not.
Click OK, it will appear as below:
24 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
4.2.6 Delete Equipment
User can choose the equipment to be deleted in the left column, and then click the “delete” item
in the pull down menu which appears by clicking the right mouse key.
4.2.7 Save Configuration
After finishing all the parameters setting, user can click
button on the toolbar to
save the modifications to the device’s flash, while user can also reload the saved parameters
25 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
from device’s flash and refresh the device’s parameters setting according to the loaded values
by clicking
button on the toolbar to popup the “save
Alternatively, user can also click the
file” dialog box, which gives prompts to save all the device’s parameters as binary files in the
computer’s hard disk.
Similarly, user can choose to click the
button on the toolbar to popup the read
file dialog box, to read the stored binary file and set the device’s parameters according to the
loaded binary files.
4.3 EN 5008 8 in 1 MPEG-4 AVC/ H.264 HD Encoder Operation
User can choose the encoder in the device tree; the procedure will display the encoder interface
in operating area. The interface is mainly composed of encoding video parameters, audio
parameters and the encoding system parameters, output parameters and etc.
4.3.1 Parameters Setting
26 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Users can click Equipment Name on the node tree and enter in the Parameter interface by
clicking
and
or
to configure the parameters.
4.3.1.1 General Parameters
Users
can
check
information in this area.
version
Set: to make the current parameters shown in the SNMP software activate.
Get: to read the current device’s activating parameters and show them on SNMP software.
 IP Out Enable
Check the checkbox with “√”, then the IP output is enabled, otherwise it is not. Users can
decide whether to open the IP output function or not.Users can modify the IP address here as
well.
 IP Out Address/Service IP Address/Service Mask/Service Gateway
Users can set the address by modifying the value in these four fields.
 ASI Output Channel
27 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
This device supports 1 MPTS (Multiple Programs Transport Stream) and 8 SPTS (Single
Programs Transport Stream) output. User can click
to triger a pull-down list to select the
output type.
 Output Port
To set the output port by modifying the value in this field.
 Original Network ID
This 16-bit field gives the label identifying the network ID of the originating delivery system.
The value ranges from 0 to 0xFFFF.
 Transport Stream ID
This is a 16-bit field which serves as a label for identification of this TS from any other
multiplex within the delivery system. The value ranges from 0 to 0xFFFF.
 Output Bit Rate (Mbps)
This includes the effective bit-rate of encoding channel 1-8, the effective bit-rate from ASI
input and the bit-rate of stuffed null packets.
 UDP Stream TS Package
Users can set the amount of TS packages here.
 NIT Insertion
In this field, users can decide whether to effect the NIT (Network Information Table) insertion
function.
 SDT Insertion
In this field, users can decide whether to effect the SDT insertion function.
 MPTS Filter Null Packet
If this function is effected, then the null packets in IP output stream will be filtered.
 PSI/SI Editor
This button will trigger the PSI/SI Editor for some users’ advanced usage. For more detail,
please refer to the manual of PSI/SI.
4.3.1.2 Video Parameters (Parameters->Channel->CH0X)
28 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Input channel selection area. The interface and
setting principle of each channel are the same.
Video Config Area:
It is to configure video
manually except resolution
which automatically displays
the resolution of source signal
and it is read-only.
Audio Config Area:
It is to configure
manually.
audio
If any parameter is modified, it is supposed to click Set
parameters activate and click Get
to make the modified
to read and effect the current device’s activating
parameters.
4.3.2 Multiplexing
29 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
CH01-CH08: The 8 HDMI
Encoding Channels
CH09: The 1 ASI Input Channel
The programs in the left column represent all input programs and which port they come from,
while the programs in the right column represent the output programs and from which port they
are from. User can parse the programs of each channel and multiplex those programs to the
output. Moreover, user can modify the output programs’ Program Name, PMT, PCR, video,
audio PID.
: Check this box the set the PID Mapping
: To refresh the inputting terminal and get the inputting information
: To refresh the outputting terminal and get the outputting information
: Multiplex the input programs to the output channels after selecting the target
program with
. The system will automatically allot the program to the relevant output
channel.
: Cancel the multiplexed programs.
: To modify the output programs’ Program Name, PMT, PCR, video, or audio PID
as needed. To modify program information, user can select the target program in output part
first and click this button to pop up a dialog box as below:
30 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Select the target item and input the new value in the box below, then click
to effect the modification.
: The parsing overtime value
4.3.3 Tables
4.3.3.1 PID Filter Table
31 / 43
Antik Technology / www.antiktech.com
and
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Users can operate PID filter in this table by checking the check boxes of corresponding items
and click CONFIRM to effect.
Refresh: getting PID filter table from the device
Setting: submitting the PID filter table to the device
Check All: selecting all the selections of the list
After user selects one PID in the table, then the corresponding output PSI/SI table will not be
sent to the output stream.
4.3.3.2 PID Pass
User can decide to bypass the inputting PID as needed in this interface.
In some occasions, there are some PIDs which won’t belong to any program, such as EPG, NIT
tables, and so on, but user just wants to pass them through the multiplexing module without
changing anything. This is the main purpose of this function.
The display will show as below when user clicks “Add” button.
32 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Input PID and Output PID
The Old (Input) PID is the PID number in the TS from given Port. The correspondent New
(output) PID number could be same as input PID number while it could be different if a PID
remapping is needed.
Modify the data as needed and click OK to confirm. The PID then will be bypassed and listed
in the table as below.
User can also modify or delete the added PID through the corresponding buttons at right.
4.3.3.3 NIT Parameters
NIT: Network Information Table.
NIT table is a very important table for describing the network and TS. Users can set the parameters of the
output NIT table.
33 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
:The parameter describes the output TS’s network ID
:The parameter describes the output TS’s network name.
Insertion private description
:This checkbox will allow user to insert the private descriptor into the
output TS. The private descriptor includes two parts. One is descriptor tag, and the other is
descriptor information.
:The Descriptor Tag is an 8-bit field which identifies each descriptor.
:The Descriptor Data is the detailed information of the private description.
:Users can add the cable transmission descriptor in this Add button, and it will pop
34 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
up the following dialogue box, say, the added descriptor is apply for the DVB-C network.
The interface will show as below after the NIT parameters being added:
:The “Modify” button will trigger a modify window and allow user to modify
the selected items in the NIT.
:The “Delete” button will remove the selected items in the NIT.
:The set “Button” will send the NIT to the chosen output Port.
4.3.4 Real-time Monitor
There will be a real-time bit rate chart generating in the monitor for users to check the bit rate
information.
35 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
4.4 Other Settings
4.4.1 Difference between Set and Remote Save
In many cases during the configuration of parameters in NMS, users save the modified
configuration by clicking “Set”, in which way the configuration can only be saved temporarily
and will restore the last saved configuration if the device reboots. To save the configuration
permanently, it is required to operate through “Remote Save” on the toolbar explained in 4.2.7.
This is the difference between “Set” and “Remote Save”.
4.4.2 IP Modification
Users can click Operate and select Modify IP in the drop-down list, and a dialog box presents
36 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
itself as shown below. Users input the new NMS IP Address for the device and click OK button
to confirm.
Users can then note the indicator light turns red, which signifies the equipment has
disconnected. Users then can refer to below prompts to edit the property by inputting the new
IP to re-connect the equipment.
Input the new IP Address in the box and click OK button, then the device will be connected
again.
37 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
After finishing all the parameters setting, user should click
button on the
toolbar to save the modifications to the device’s flash.
4.4.3 User Add
When logging in, user will note that the default user name is admin and no password. User can
add users and passwords as needed.
User clicking “Setting” in the menu bar and selecting “User Setting” in the pull-down list, the
below dialog box will pop out as shown below. Select the “Edit Information” by marking the
check box with “√”, user can input the new username and new password as prompts below. It
is required to click
to add the new user and then click
new setting.
38 / 43
Antik Technology / www.antiktech.com
to save the
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
39 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Chapter 5 Troubleshooting
ANTIK’s ISO9001 quality assurance system has been approved by CQC organization. For
guarantee the products’ quality, reliability and stability. All ANTIK products have been passed
the testing and inspection before ship out factory. The testing and inspection scheme already
covers all the Optical, Electronic and Mechanical criteria which have been published by
ANTIK. To prevent potential hazard, please strictly follow the operation conditions.
Prevention Measure
 Installing the device at the place in which environment temperature between 0 to 45 °C
 Making sure good ventilation for the heat-sink on the rear panel and other heat-sink bores
if necessary
 Checking the input AC within the power supply working range and the connection is
correct before switching on device
 Checking the RF output level varies within tolerant range if it is necessary
 Checking all signal cables have been properly connected
 Frequently switching on/off device is prohibited; the interval between every switching
on/off must greater than 10 seconds.
Conditions need to unplug power cord
 Power cord or socket damaged.
 Any liquid flowed into device.
 Any stuff causes circuit short
 Device in damp environment
 Device was suffered from physical damage
 Longtime idle.
 After switching on and restoring to factory setting, device still cannot work properly.
 Maintenance needed
40 / 43
Antik Technology / www.antiktech.com
EN 5008 8-in-1 MPEG-4 AVC/H.264 HD User’s Manual
Chapter 6 Packing list
 EN 5008 8 in 1 MPEG-4 AVC/H.264 HD Encoder
1pcs
 User’s manual
1pcs
 HDMI cable
8pcs
 ASI cable
1pcs
 Power cord
1pcs
41 / 43
Antik Technology / www.antiktech.com