Moog Videolarm PDW7CS-9 Instruction manual

© 2009-2010, Moog Videolarm, Inc. All Rights Reserved
PDW7CS-9
Explosion-Proof: Purge/Pressurization Unit
www.videolarm.com
Installation and Operation Instructions for the following models:
PDW7CN-9
PDW7CS-9
IP Network Ready 7” Explosion-Proof PurgeDome™ Outdoor PTZ Camera Systems for Hazardous environments UL approved for Class 1, Division II applications. Includes Purging System and Lines. With 23x zoom Day/Night
camera, MPEG-4 & MJPEG video compression, Full D1. Clear dome, with 24VAC input, heater/ blower
Analog 7” Explosion Proof PurgeDome™ Outdoor PTZ Camera Systems for Hazardous environments UL approved for Class 1, Division II applications. Includes Purging System and Lines. With 23x zoom Day/Night camera, MPEG-4 & MJPEG video
compression, Full D1. Clear dome, with 24VAC input, heater/ blower Before attempting to connect or operate this product, please read these
instructions completely. To be used with the 81-IN5409 Instruction Manual.
CERTIFIED
81-IN5410
10-19-2010
IMPORTANT SAFEGUARDS
1
Read these instructions.
2
Keep these instructions.
3
Heed all warnings
4
Follow all instructions.
5
Do not use this apparatus near water.
6
Clean only with damp cloth.
7
Do not block any of the ventilation openings. Install in accordance with the
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
manufacturers instructions.
8
Cable Runs- All cable runs must be within permissible distance.
9
Mounting - This unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit.
Accordingly:
a. The installation should be made by a qualified installer.
b. The installation should be in compliance with local codes.
c. Care should be exercised to select suitable hardware to install the unit, taking into
account both the composition of the mounting surface and the weight of the
unit.
10 Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus ( including amplifiers) that produce heat.
11 Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
12 Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
13 Only use attachment/ accessories specified by the manufacturer.
14 Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
15 Unplug this apparatus during lighting storms or when unused for long periods of time.
16 Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled of objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Be sure to periodically examine the unit and the supporting structure to make sure that the
integrity of the installation is intact. Failure to comply with the foregoing could result in the
unit separating from the support structure and falling, with resultant damages or injury to
anyone or anything struck by the falling unit.
UNPACKING
Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper.
Be sure to save:
1 The shipping carton and packaging material.
They are the safest material in which to make
future shipments of the equipment.
2 These Installation and Operating Instructions.
SERVICE
If technical support or service is needed, contact us
at the following number:
TECHNICAL SUPPORT
AVAILABLE 24 HOURS
1 - 800 - 554 -1124
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER ( OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SEVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with an arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of non-insulated “dangerous voltage”
within the product’s enclosure that may be
of sufficient magnitude to constitute a risk
to persons.
Este símbolo se piensa para alertar al usuario a la
presencia del “voltaje peligroso no-aisIado” dentro del
recinto de los productos que puede ser un riesgo de
choque eléctrico.
Ce symbole est prévu pour alerter I’utilisateur à la
presence “de la tension dangereuse” non-isolée dans la
clôture de produits qui peut être un risque de choc
électrique.
Dieses Symbol soll den Benutzer zum Vorhandensein der
nicht-lsolier “Gefährdungsspannung” innerhalb der
Produkteinschließung alarmieren die eine Gefahr des
elektrischen Schlages sein kann.
Este símbolo é pretendido alertar o usuário à presença
“di tensão perigosa non-isolada” dentro do cerco dos
produtos que pode ser um risco de choque elétrico.
Questo simbolo è inteso per avvertire I’utente alla
presenza “di tensione pericolosa” non-isolata all’interno
della recinzione dei prodotti che può essere un rischio di
scossa elettrica.
The exclamation point within an equilateral
triangle is intended to alert the user to
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Este símbolo del punto del exclamation se piensa para
alertar al usuario a la presencia de instrucciones
importantes en la literatura que acompaña la
aplicación.
Ce symbole de point d’exclamation est prévu pour
alerter l’utilisateur à la presence des instructions
importantes dans la littérature accompagnant
l’appareil.
Dieses Ausruf Punktsymbol soll den Benutzer zum
Vorhandensein de wichtigen Anweisungen in der
Literatur alarmieren, die das Gerät begleitet.
Este símbolo do ponto do exclamation é pretendido
alertar o usuário à presença de instruções importantes
na literatura que acompanha o dispositivo.
Questo simbolo del punto del exclamaton è inteso per
avvertire l’utente alla presenza delle istruzioni importanti
nella letteratura che accompagna l'apparecchio.
LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS
VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship,as follows:
PRODUCTCATEGORY
PARTS
LABOR
All Enclosuresand Electronics
Five (5) Years
Five (5) Years
Pan/Tilts
Three (3) Years **6 months if used in autoscan
Three (3) Years **6 months if used in autoscan
/tour operation
Poles/PoleEvators
Three (3) Years /tour operation
Three (3) Years
Warrior/Q-View/I.R.Illuminators
Five (5) Years
Five (5) Years
Five (5) Years **6 months if used in autoscan
SView Series
Five (5) Years **6 months if used in autoscan
/tour operation
Controllers
Five (5) Years /tour operation
Five (5) Years
PowerSupplies
Five (5) Years
Five (5) Years
AccessoryBrackets
Five (5) Years
Five (5) Years
During the labor warranty period, to repair the Product,Purchaserwill either return the defective product, freight prepaid, or deliver it to Videolarm Inc.
an equal degree of protection with a
Decatur GA.The Productto be repaired is to be returned in either its original carton or a similar package
RMA# (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA#you must contact our TechnicalSupport
Team at 800.554.1124,extension 101.Videolarm will return the repaired Productfreight prepaid to Purchaser.Videolarm is not obligated to provide
Purchaserwith a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchasermust pay all labor and/or
parts charges.
The limited warranty stated in these product instructions is subject to all of the following terms and conditions:
TERMS AND CONDITIONS
1. NOTIFICATIONOF CLAIMS: WARRANTYSERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice
with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the
warranty period. If after investigation Videolarm determines that the reported problem was not covered by the warranty, Purchaser shall pay Videolarm
for the cost of investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall
extend the warranty period as to the entire Product. The
warranty on the repaired part only shall be in
for a period of ninety (90) days
following the repair or replacement of that part or the remaining period of the Product parts warranty, whichever is greater.
2. EXCLUSIVE REMEDY: ACCEPTANCE:Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair
any Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.
3. EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service
during the warranty period which is subjected to any of the following: abuse, improper use: negligence, accident, lightning damage or other acts
of God (i.e., hurricanes, earthquakes),
failure of the end-user to follow the directions outlined in the product instructions, failure of the
end-user to follow the maintenance procedures recommended by the International Security Industry Organization, written in product instructions,
for regular
or recommended in the service manual for the Product. Furthermore, Videolarm shall have no liability where a schedule is
replacement or maintenance or cleaning of certain parts (based on usage) and the end-user has failed to follow such schedule; attempted repair by
personnel; operation of the Product outside of the published environmental and electrical parameters, or if such Product’s original
(trademark, serial number) markings have been defaced, altered, or removed. Videolarm excludes from warranty coverage Products sold
AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser. All software and accompanying
documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided
otherwise in any documentation or license agreement furnished with the Product.
4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMEROF WARRANTY
EXCEPT FOR THE FOREGOING WARRANTIES, VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH
REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE
STATE STATUTE. VIDEOLARM HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-VIDEOLARM
PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS PURCHASER CHOOSES TO CONNECT TO PRODUCT.
LIMITATION OF LIABILITY
THE LIABILITY OF VIDEOLARM, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND
WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE
PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT
OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
Content of Box
Content of Box
PROTECTED
CAMERA
ENCLOSURE
SUPPLIED 1/4 “ & 3/8 ” POLY TUBING
PAN / TILT
DOME
PURGE / PRESSURIZATION UNIT
HARDWARE
1




Unit is shipped with 100’ (max) flex tubing (3/8” & 1/4”) to connect enclosure to purge pressurized
unit. 2 fitting are provided as shown in the diagrams.
2
ENCLOSURE SUPPLY OUTLET
(3/8 “ Push-in Fitting)

ENCLOSURE REFERENCE INLET

(1/4 “ Push-in Fitting)
PURGED / PRESSURIZATION
UNIT
ELECTRICAL ALARM WIRING
CONDUIT AND SEAL
(Customer Supplied)
SYSTEM SUPPLY INLET
(3/8 “ SS Compression Fitting)
3
English
NOTES
• To ensure adequate protective gas flow to the protected enclosure, all piping and tubing must be
fully reamed.
• Precaution must be taken to prevent crimping and other damage to protective gas piping and
tubing. Caution must be used when opening/closing swing panel to prevent tubing kinks.
• Supplied 1/4” & 3/8” Poly Tubing have ferrule, nut & insert preset. Use that end for connecting to
power box. Cut other end to attain desired length and connect to push-in fittings on
Purge/Pressurization Unit.
• The Tamper-Proof (Primary) Regulator is intended to prevent tampering, while allowing a more
stable setpoint to be achieved in the small, tightly sealed enclosure where the protective gas flow is
critically low and difficult to stabilize. A 5/64” Hex Key or Allen Wrench is required to operate.
• When performing Initial Purge/Pressurization, adjust Primary Regulator to 5 psi. Normal operating
pressure is 2.5 inches of water at Dome Pressure Gauge. Balance Primary and Secondary
Regulators for continuous purge by alternately adjusting Primary (5 psi) and Secondary (2.5 inches
of water).
4
SYSTEM MOUNTING
O 0.32
4 places
10.0
PEPPERL+ FUCHS
14.7
5
TUBING CONNECTION DIAGRAMS
ENCLOSURE SUPPLY OUTLET
ENCLOSURE REFERENCE INLET
PEPPERL+ FUCHS
PURGE/PRESSURIZATION UNIT
SYSTEM SUPPLY INLET
6
TUBING CONNECTION DIAGRAMS
DOME
PRESURE GAUGE
[ENCLOSURE]
EXP
PRESURE
SWITCH
ATMOSPHERIC
REFERENCE
SDOEN OF WOSTOE
.3
.2
.1
.4
SAFE
0
HIGH
LOW
.5
ENCLOSURE PRESSURE
REFERENCE
OFF
PRIMARY
REGULATOR
SYSTEM
SUPPLY
INLET
SECONDARY
REGULATOR
ON
5
500
4
400
3
300
2
20
1
10
SUPPLY
METER
FLOWMETER
PROTECTED
CAMERA
ENCLOSURE
7
CONNECTION SIZES, LENGTHS & BENDS
CAMERA
PEPPERL+ FUCHS
REFERENCE
GAS SUPPLY
(System Supply)
PROTECTED
CAMERA
ENCLOSURE
CAMERA
PURGE/PRESSURIZATION UNIT
SUPPLY
System Supply
3/8” OD SS Tubing
Fully Reamed
MAXIMUM:
20 ft / 10 bends
Camera Supply
Camera Reference
SUPPLIED
3/8” Poly Tubing
SUPPLIED
1/4” Poly Tubing
100 ft MAX
100 ft MAX
SET-UP PROCEDURE
• See supplied Model 1001A Installation and Operation Manual for Class I Purging Set-up.
The use of a temporary SCFH flowmeter is unnecessary. Use the permanently installed flowmeter on the swing
panel in the Purge/Pressurization Unit.
• See supplied Model 1001A Installation and Operation Manual for additional installation and operation information.
8
POLE MOUNT CLIPS
9
REMOVE INSERT
CAMERA
ENCLOSURE
POWER
SUPPLY
BOX
DOME
TRIM
RING
PAN
TILT
UNIT
Carefully unpack both boxes and compare
with parts list.
Open the metal power supply box on the camera
enclosure and remove cardboard packing
materials.
10
11
WALL MOUNT:
Attach unit securely to the wall mount using (4) 3/8”
or 8mm hardware (not supplied).
12
INPUT: (120VAC 1A
240VAC .5A)
220-240VAC INPUT
The power box may be pole mounted with the
pole support clips. (Stainless steel straps not
provided).
13
110-120VAC INPUT
240Vac
120Vac Input
Input
The box is designed for either 120 or 240 VAC input
single phase. Line (L) and Neutral (N) wires should
be connected as marked on the board and
plugged into the corresponding voltage for the
input single phase.
Main
Switch
Connect incoming ground to ground post as
shown.
OUTPUT: (24VAC
84VA)
14
HEATERS CAMERA
52 WATTS
MAX
32 WATTS
MAX
Connect
Housing
Power
24Vac Power
To Housing
Optional 24Vac
Output
Main
Switch
Internal resettable fuses are supplied for the main 24VAC output lines. Do not connect heaters
to camera output. The PB24 is not designed for 3 phase or 208V systems.
15
16
CAPTIVE SCREW
Remove Pan/ Tilt from shipping carton.
Install in base bracket in housing.
To secure in place, tighten captive screw.
See S-View Pan/Tilt instructions for additional
details.
• If required the Pan/ Tilt and dome may be installed
before mounting the entire assembly.
17
18
To install the dome align the tabs and twist
counter clockwise to secure.
Hand tighten the screws on the dome.
Recommended torque 12 inches/lb (1.35Nm).
Part Number
Replacement Parts List
1
2
Description
1
RP65PT851200
PAN TILT
2
PR25DCP71000
TRIM RING ASSEMBLY WITH
CLEAR DOME
Product Registration/Warranty
Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you
with only the highest quality products available with unmatched customer service levels that are secondto-none in the security industry.
Should a problem arise, rest assure that Videolarm stands behind its products
by offering some of the most impressive warranty plans available: 3 Years
on all Housings, Poles, Power Supplies, and Accessories and 5 Years on
all camera systems (SView, QView, Warriors), and InfraRed Illuminators.
Register Your Products
Option 1: Online Option 2: Mail-In
Take a few moments and validate your purchase with our Online Product Registration Form
www.videolarm.com/productregistration.jsp
at
or complete and mail-in the bottom portion of this flyer.
Register your recent Videolarm purchases and benefit from the following:
• Simple and Trouble-Free RMA process
• Added into customer database to receive product updates / news
• Eliminate the need to archive original purchase documents:
Receipts, Purchase Orders, etc…
Cut at the dotted Line
Place in envelope, affix stamp and mail to:
Main Contact Info
First Name:
Professional Title:
Company:
Address 1:
Address 2:
City:
State / Province/Country: Zip / Postal Code:
Phone Number: Product Information Last Name:
Please Circle One:
Product Description
Serial #
(Available only for Camera Systems, IR Illuminators, Wireless Devices)
PO#
E-mail Address:
Name & Location of Company / Store where Purchased:
(City, State, Country)
Videolarm Product ID
Videolarm ATTN: Warranty
2525 Park Central Ave.
Decatur, GA 30035
Business
Personal