Monogram ZBD1850 Owner`s manual

Appliances
Installation Instructions
If gou have questions, call 800.626.2000 or visit our website at: www.monogram.com
Built-In
Dishwashers
ZBD1850*
ZBD1870
*For ZBD1850 also refer to the
instructions provided on the template
packed with that model
Safetg Information
BEFORE
YOU BEGIN
Read these instructions completelg and
curefullg.
IM PORTANT
Observeallgoverningcodes and
I L J I'_ t'_
I"1"1" A k I'It"
I m i"%Ji_ I _1_1|The dishwasherMUST
be installed
toallowforfutureremovalfromtheenclosure
if service is required.
If gou received a damaged dishwasher, gou should
immediatelg contact gour dealer or builder.
ordinances.
Note to Installer - Be sure to leave these instructions for the
consumer's and local inspector's use.
Note to Consumer - Keep these instructions with gour
Owner's Manual for future reference.
Skill Level -Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills. Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GE Appliance Warranty. See warranty information.
Completion Time - 1 to 3 Hours. New installations require
more time than replacement installations.
Optional Accessories - See the Owner's Manual for available
custom panel kits.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGS shown
throughout these instructions.
While performing installations described in this booklet,
gloves and either safetg glasses or goggles should be worn.
For Monogram local service in gour area, 1.800.444.1845.
For Monogram service in Canada 1.888.880.3030.
For Monogram Parts and Accessories, call 1.800.626.2002.
CONTENTS
Installation Preparation
8
Step 5, Install 90° Elbow ...............................................................................
Parts Supplied ...................................................................................................
5
9
Step 6, Position Water Line and House Wiring ..................................
Materials You Will Need ...............................................................................
5
9
Step 7, Install Drain Hose Through Cabinet ........................................
Tools You Will Need ........................................................................................
5
9
Step 8, Slide Dishwasher Partiallg Into Cabinet ................................
Prepare Dishwasher Enclosure .................................................................
4
10
Step 9, Position Dishwasher Under Countertop ............................
!!
Drain Requirements .......................................................................................
4
Step !0, Level Dishwasher .......................................................................
Prepare Electrical Wiring .............................................................................
5
11
Step 11, Secure Dishwasher To Cabinet ............................................
12
Prepare Hot Water Line ................................................................................
6
Step !2, Connect Water Supplg ............................................................
!2
Step !5, Connect Drain Line ....................................................................
Installation Instructions
!5
Step !/4, Connect Power Supplg ............................................................
Step 1, Check Door Balance .......................................................................
6
15
Step 15, Pre-Test Checklist .......................................................................
Step 1A, Adjust Door Springs .....................................................................
6
14
Step !6, Dishwasher Wet Test ................................................................
Step 2, Adjust Leveling Legs .......................................................................
8
!/4
Step 17, Replace Toekick ..........................................................................
Step 3, Remove Toekick ................................................................................
8
!/4
Step !8, Literature ........................................................................................
Step 4, Install Power Cord ...........................................................................
8
installation Preparation
PARTS SUPPLIED:
[] Two #8 Phillips head wood screws, 5/8" long to
secure dishwasher to underside of countertop
(in literature package).
2 Wood Screws
MATERIALS YOU WILL NEED:
[]
Ferrule, compression nut and 90 ° Elbow (3/8" NPT
external thread on one end, opposite end sized to
fit water supplg)
[] Thread seal tape
[]
90° Elbow,
Ferrule and
Compression
UL Listed wire nuts (3)
Materials
For New Installations
Nut
Hand
Shut-Off
Valve
Thread
Seal Tape
Wire Nuts {3)
Only:
[] Air gap for drain hose, if required
[] Waste tee for house plumbing, if applicable
[]
Electrical cable or power cord, if applicable
Waste Tee
Electrical
Cable
Hot Water Line
{or Power Cord, if applicable)
[] Screw type hose clamps
[] Strain relief for electrical connection
[]
Hand shut-off valve
Air
[] Water line 3/8" min. copper
Screw Tgpe
Gap
[] Coupler for extending drain line, if applicable
Strain Relief
Coupler
Hose Clamps
TOOLS YOU WILL NEED:
[]
Phillips head screwdriver
Phillips
Head
[] 5/!6" and !/4" nutdriver
[] T25 torque driver (PDW
Ilonlg)
Level
[] Carpenters square
[]
Screwdriver
f
[] 6" Adjustable wrench
[]
Level
5/16" Nutdriver
Measuring tape
6" Adjustable
T25 Torque
Driver
[] Safetg glasses
[]
Flashlight
[]
Bucket to catch water when flushing the line
Tubing Cutter
Wrench
Carpenters
Square
[] Gloves
Flashlight
For New Installations
Safetg Glasses
Measuring
Only:
[] Tubing cutter
[]
Drill and appropriate bits
[]
Hole saw set
Gloves
Bucket
Hole Saw Set
Drill and Bits
Tape
installation Preparation
PREPARE DISHWASHER
• The dishwasher must be installed so that drain hose is no
ENCLOSURE
more than 10' in length for proper drainage.
I G
To reduce the risk of electric shock, fire, or injury to persons, the
installer must ensure that the dishwasher is completelg enclosed
at the time of installation.
34-1/2"+ 1/2"
Underside of Countertop
to Floor
CLEARANCES: When
Square
and
Plumb
18" Max.
Floor MUST
be Even with
Room Floor
Plumbing and Electric Service
Must Enter Shaded Area
Figure A
S
installed into a corner,
allow 2" min. clearance
between dishwasher and
Countertop
adjacent cabinet, wall or
other appliances. Allow
25-5/8" min. clearance
from the front of the
dishwasher for door
25-5/8"
\
opening. Figure B
,_ Clearance,!or Door
/Opening
2 Minimum
• The rough cabinet opening must be at least 24" deep, 17-5/8"
to 18" wide and approximately 34-1/2" high from floor to
underside of the countertop.
Figure B
_/-'.eg
A
____
ra
DRAIN REQUIREMENTS
• Followlocal
codes and ordinances.
• Do notexceedi0'distance
todrain.
Do notconnectdrainlines
fromotherdevicestothe
dishwasherdrainhose.
NOTE: Airgap must be usedifwaste teeordisposer
connection
isless
than 18"above floor
topreventsiphoning.
Figure C
DETERMINE DRAIN METHOD
The air gap must be installed according
Method 1 - Air 6ap with Waste Tee or Disposer
An air gap must be used when required bg local codes and ordinances.
to manufacturer's
instructions.
The type of drain installation depends on the following
questions.
[] Do local codes or ordinances require an air gap?
[] Is waste tee less than 18" above floor?
If the answer to either question is YES,Method 1 MUST
be used.
• If the answers are NO,either method may be used.
CABINET PREPARATION
Figure D
• Drill a 1-1/2" diameter hole in the cabinet wall within
the shaded areas shown in Figure A for the drain hose
connection. The hole should be smooth with no sharp edges.
IMPORTANT:When connecting
drain line to disposer, check to be
_
4--- Remove
removed. DISHWASHERWILL NOT
sure that drain plug has been
DRAIN IF PLUGIS LEFTIN PLACE.
[_u
Plug
Hopper
Method 2 - Drain Hose Routing
When not using an air gap, the drain hose must be routed to form a high
loop of at least 32" to prevent siphoning.
See Step 15 on page 10.
CAUTIO :
An air gap MUST BE USEDif the drain hose is connected to
waste tee or disposer lower than 18" above the floor level.
Failure to provide the proper drain connection height with an
air gap or 32" minimum high drain loop will result in improper
draining of the dishwasher, which may cause damage.
installation Preparation
PREPARE ELECTRICAL WIRING
FORPERSONALSAFETY:
Remove house fuse or open circuit breaker
before beginning installation. Do not use
an extension cord or adapter plug with this
appliance.
Electrical Requirements
• This appliance must be supplied with 120V, 60Hz., and
connected to an individual properly grounded branch circuit
protected by a 15 or 20 ampere circuit breaker or time delay
fuse.
• Wiring must be 2 wire with ground and rated for 75°C(176°F).
• If the electrical supply does not meet the above
requirements, call a licensed electrician before proceeding.
Grounding Instructions-Cable Direct
This appliance must be connected to a grounded metal,
permanent wiring system, or an equipment grounding
conductor must be run with the circuit conductors and be
connected to the equipment grounding terminal or lead on the
appliance.
Grounding Instructions-Power Cord Models
This appliance must be grounded. In the event of a malfunction
or breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This appliance is equipped with a cord having an equipment
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is installed and
grounded in accordance with all local codes and ordinances.
-i x
I x
I
\
I
I
I
\
1
t
\
x
1-1/2" Dia.
Hole (Max.)
from
Cabinet
I
Figure E
Black
White
For models equipped with power cord: Do not modify the plug
provided with the appliance; if it will not fit the outlet, have a
proper outlet installed by a qualified technician.
Cabinet Preparation and Wire Routing
• The wiring may enter the opening from either side, rear or the
floor within the shaded area.
• Cut a !-!/2" max. diameter hole to admit the electrical cable.
Cable direct connections may pass through the same hole
as the drain hose and hot water line, if convenient. If cabinet
wall is metal, the hole edge must be covered with a bushing.
Note: Power cords with plug must pass through a separate
hole.
Electrical Connection to Dishwasher
Electrical connection is on the right front of dishwasher.
For cable direct connections the cable must be routed as
shown in Figure E.Cable must extend a minimum of 24" from
the rear wall.
The improper connection of the equipment
grounding conductor can result in electric
shock. Check with a qualified electrician or
service representative if you are in doubt that
the appliance is properly grounded. Do not
modify the plug provided with the appliance;
if it will not fit the outlet, have a proper outlet
installed by a qualified technician.
For power cord connections, install a 3-prong grounding type
receptacle in the sink cabinet rear wall, 6" min. or 18" max.
from the opening, 6" to 18" above the floor.
Installation
Instructions
PREPARE HOT WATER LINE
BEFORE YOU BEGIN
The line may enter from either side, rear or floor within the
shaded area shown in Figure F.
The line may pass through the same hole as the electrical
cable and drain hose. Or,cut an additional 1-1/2" dia. hole to
accommodate the water line. If power cord with plug is used,
water line must not puss through power cord hole.
STEP 1 CHECK DOOR BALANCE
CAUTION:
The hot water supply line pressure must be at least 20 psi.
Lower pressures could cause the water valve to leak and
cause water damage.
I
I
I
Locate and set aside the package containing
2 Phillips head countertop mounting screws
and 2 additional toekick screws (located in
the literature package).
To check the door balance, hold the top of the dishwasher
firmly.
Open the door slowly. If the door drops when released, you
will need to increase spring tension. If the door closes when
released, you will need to decrease tension.
If adjustments are needed, see Step 1A. If no adjustments are
needed, skip to Step 2.
\
\
STEP 1A ADJUST DOOR SPRINGS
\
\
(IF NECESSARY)
FOR ZBD1870 MODELS
For ZBD1850 models, refer to the instruction
template packed with that model.
To adjust the door springs, you will need to remove the
dishwasher side panels.
From
Cabinet
Cabinet Face
3" From Floor
Figure F
Water
provided on the
Line Connection
Turn off the water supply.
Install a hand shut-off valve in an accessible location, such
as under the sink. (Optional, but strongly recommended and
may be required by local codes.)
Water connection is on the left side of the dishwasher. Install
the hot water inlet line, using no less than 3/8" O.D.copper
tubing. Route the line as shown in Figure F and extend
forward at least 18" from rear wall.
Adjust water heater for !20°F to !50°F temperature.
Flush water line to clean out debris.
The hot water supply line pressure must be 20-120 PSI.
CAUTIO
To remove the side panels:
• Remove the screws from the top and back of each
dishwasher side panel, sixteen screws total. Open the door
and remove the four screws securing the panels to the inside
door frame.
Y
-- Screws
Screws
Screws
/
:
Opening the door will cause the dishwasher
to tip forward. Do not open the door
until
you are ready
to install the dishwasher. If it is
necessary to open the door, hold
the top of the dishwasher securely
with one hand and hold the door
with the other hand.
• crews
Rear
Front
Figure G
Figure H
Installation
Instructions
Lay the dishwasher on its back. Remove the four screws
securing the toekick to the dishwasher, and remove the
toekick.
Remove the side panels and set the dishwasher upright.
To adjust the door springs:
Pull the spring adjustment pin out of the holes, insert in the
next highest or lowest hole and test again.
Increase
Decrease
Figure K
Remove the single screw just above and to the side of each
front leveling leg.
Figure J
Adjust both door springs to the same tension.
Continue moving the spring pin until door is balanced.
Replace the dishwasher side panels and proceed to Step 2.
Installation
Instructions
STEP 2 ADJUST LEVELING LEGS
Hove the dishwasher close to the installation location and lag
it on its back.
O
Adjustto
Installation
STEP 4 INSTALL POWER CORD
Skip this step if dishwesher will be direct wired.
Use Power Cord Kit WX09X70910, available for purchase
from an authorized GEAppliance Dealer. The power cord and
connections must complg with the National Electrical Code,
Section 422 and/or local codes and ordinances.
Maximum power cord length is 6'.
A
Remove
Junction Box
B CheckThat White, Blackand
Green DishwasherWiresAre Threaded
Thru Holein Back
Cover
Ground
Height
/ White
I
Figure L
D UseULListed
Wire Nuts
Measure installation height and dishwasher height. Extend
leveling legs out from the dishwasher base, 1/2" less than
installation height.
C
InsertPower
CordWiresThru
StrainRelief
and Tighten
STEP 3 REMOVE TOEKICK
Figure N
• Remove the 4 toekick screws. Lift off the 2 piece toekick.
Connect incoming power cord white (or ribbed) to dishwasher
white, black (or smooth) to black and ground to dishwasher
green wire. Use UL listed wire nuts of appropriate size.
Replace junction box cover. Be sure wires are not pinched
under the cover.
STEP 5 INSTALL 90 ° ELBOW
• Wrap 90° elbow with thread seal tape.
Install a 90 ° elbow onto the water valve.
Fill
Hose
Figure M
90 °
Elbow
\
Thread
Seal Tape
Water
Valve
Bracket
Figure O
Do not over tighten 90 ° elbow, water valve bracket could
bend or water valve fitting could break.
Position the end of the elbow to face the rear of the
dishwasher.
Installation
Instructions
STEP 6 POSITION WATER LINE AND
HOUSE WIRING
STEP 8 SLIDE DISHWASHER PARTIALLY
INTO CABINET
, Position water supply line and house wiring on the floor of
the opening to avoid interference with base of dishwasher
and components under dishwasher.
DO NOT PUSH AGAINST FRONT PANELWITH KNEES.
DAMAGE WILL OCCUR.
, Slide dishwasher into the opening a few inches at a time.
_Sides
Re osition Dishwasher
Water Wiring
Line
Figure P
Front Door Panel With
Knee. Damage to The
Door Panel Will Occur.
STEP 7 INSTALL DRAIN HOSE THROUGH
CABINET
• Stand the dishwasher upright and position in front of the
opening. Insert drain hose into cabinet wall hole. If a power
cord is used, guide the end through a separate hole.
Figure R
• As you proceed, pull the drain hose through the opening
under the sink. Stop pushing when the dishwasher is a few
inches forward of adjacent cabinetry.
• Make sure drain hose is not kinked under the dishwasher and
there is no interference with the water line and wiring or any
other component.
Maximum
Drain Hose
Length 10"
Insulation
Blanket
House
Wiring
Power Cord
{If Used)
Figure Q
TIP: Position water line and house wiring on the floor
to avoid interference with base of dishwasher.
installation
instructions
STEP 9 POSITION DISHWASHER UNDER
COU NTERTOP
• Push the dishwasher into the cabinet.
• Push the sides with your hands. Do not use your knee against
the door since door damage will occur.
• Check that the tub insulation blanket does not get
"bunched-up" or interfere with the springs as you slide it
into the cabinet.
• Center the dishwasher in the opening.
• Front of door panel should be flush with face of cabinet.
• Carefully open and close the door to ensure that the door
panel does not catch or rub on the cabinet frame.
• If the door catches or rubs on the frame, reposition and/or
level the unit (see Step 10) until the door moves freely and
does not contact the cabinet frame.
/ _ \
Reposition Dishwasher
by Grasping Both
s With Hands
)
Do Not Push Against_
Front Door Panel With_
Knee. Damage to The \
Door Panel Will Occur.
Figure S
The controls on these models are designed to be hidden by
your countertop. Align the dishwasher as shown in Figure
T. Leave a 1/2" minimum gap between the underside of the
countertop and the top of the dishwasher door as shown in
Figure W.
Note: If the drain hose gets trapped behind the unit it can
prevent the controls from being hidden by the countertop.
Note: If this dishwasher is replacing an existing dishwasher, the
old countertop bracket screw holes may not be in the correct
position to accept a top-control model. New holes may be
required.
Tip: The leveling legs can be used to increase or decrease
the amount of gap between the controls and the countertop
affecting the visibility of the controls.
IM PORTANT-
J
Door
Fits and
Swings
Back
Behind
Cabinet
Frame
/
Correct
Alignment
"---
Incorrect /
Alignment
Figure T
Top View
Leave a 1/2" minimum
gap between
the controls and the underside of the countertop
to prevent
condensation
and damage to the control panel from
screwheads.
I
I
I
I
I
I
I
I
Controls Hidden
by Countertop
Figure U
Countertop
i/2"
Min.
I,
lo
Figure V
I
Dishwasher
Door
Figure W
Installation
Instructions
STEP 10 LEVEL DISHWASHER
IN PORTANT-
Dishwasher must be level for proper
dish rack operation and wash performance.
• Make sure 1/2" minimum gap is maintained (see Figure T).
Place level on door to check that the dishwasher is level sideto-side. Place level on rack track inside tub to check that the
dishwasher is level front-to-back.
STEP 11 SECURE DISHWASHER
TO
COUNTERTOP
OR CABINET
In this step gou will need
the 2 Phillips special head
screws set aside prior to
Step 1. The dishwasher
must be secured to the
countertop or the cabinet
sides. When countertops
are made of wood,
use Method 1. When
Side-Mounting
Bracket
FigureZ
countertops are granite or
other materials that will not
accept screws, use Method
2 to secure dishwasher at the sides.
Use
Level to
Check
Frontto-Back
Use
Level to
Check
Side
Figure AA
IMPORTANTDrive screws straight
and flush. Protruding
screw heads will
Brackets
Wood Counterto I
scratch the top or
sides of the control
panel and can interfere
Figure X
If the dishwasher is not level, adjust the four leveling legs
individuallg.
with door closing.
Method 1
Figure BB
Secure dishwesher to wood countertop
Fasten the dishwasher to the underside of the countertop
with the 2 Phillips special head screws provided.
Method 2
Secure dishwasher with side-mounting brackets
Remove plug buttons (one on each side).
Install screws through the dishwasher side mount bracket
and into the adjacent cabinet on each side. Reinstall plug
buttons.
Granite Countertop
\
/\
Figure V
Tip: Pull lower rack out, about halfwag. Check to be sure the
rack does not roll forward or back into dishwasher. If the rack
rolls in either direction, the dishwasher must be leveled again.
If door hits the tub, the dishwasher is not installed correctlg.
Adjust leveling legs to align door to tub.
Plug Buttons--_
Screws
Figure CC
Either Method
IM PORTANT- After
dishwasher
Step 9.
leveling, verifg that the
is still in the correct position shown in
Countertop
/
1/2"___
Min. I
Dishwasher
Door
Figure DD
When step is complete, close dishwasher door and verifg that
gap between countertop and top of dishwasher door is at
least 1/2".
11
Installation
Instructions
STEP 12 CONNECT WATER SUPPLY
DRAIN LINE INSTALLATION
Connect water supplg line to 90 ° elbow.
• Slide compression nut,
then ferrule over end of
CompressionNut
water line.
Ferrule
Insert water line into 90 °
elbow.
Slide ferrule against
Hot Water z
elbow and secure with
_o
Elbow SupplyLine
compression nut.
f--<x
• Connect drain line to air gap, waste tee or disposer using
either previously determined method.
Method 1 - Air gap with waste tee or disposer
Insert the drain hose to air gap as shown.
Figure EE
Waste Tee Installation
IMPORTANT- Check
tobesure
thatdoor
does
spring
not rub or contact the fill hose or water supplg line. Test bg
opening and closing the door. Re-route the lines if a rubbing
noise or interference occurs.
Disposer Installation
Figure HH
Method
2 - Drain
Hose
Routing
Route the drain hose of the dishwasher to a minimum
the floor with the supplied hanger as shown.
height of 32" from
m
STEP 13 CONNECT DRAIN LINE
FOLLOW ALL LOCAL CODESAND ORDINANCES.
The molded end of the drain hose will fit 5/8" through !"
diameter inlet ports on the air gap, waste tee or disposer.
Determine size of inlet port
Cut drain hose connector on the marked line, if required, to fit
the inlet port.
Cutting Lines
Waste Tee Inst Ilati
Disposer Installation
Figure II
IN PORTANT-
Either one of the above methods
must be used or dishwasher
/4
Figure FF
If a longer drain hose is required, add up to 42" of length for
a total of 10' to the factory installed hose. Use 5/8" or 7/8"
inside diameter hose and a coupler to
connect the two
Figure GG
Coupler
Hose Clamp
Hose Clamp
Secure the drain hose to the air gap, waste tee or disposer
with clamps.
Note: TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED !0' FOR
PROPER DRAIN OPERATION.
12
properlg.
IN PORTANT- When
IMPORTANT:
Do not cut corrugated
portion of hose
Secure the
connection with
hose ends.
hose clamps.
will not operate
connecting
drain line to disposer, check to be sure
that drain plug has been removed.
DISHWASHERWILL NOT DRAIN IF
PLUGISLEFT IN PLACE.
[_
Hopper
Plug
4--- Remove
Tip: Avoid unnecessary service call charges. Always be sure
disposer drain plug has been removed before attaching
dishwasher drain hose to the disposer.
Installation
Instructions
STEP 14 CONNECT POWER SUPPLY
STEP 15 PRETEST CHECK LIST
Skip this step if equipped with power cord.
Verifg that power is turned offat the source.
Remove junction box cover "A".
Review this list after installing your dishwasher to avoid
charges for a service call that is not covered by your
warranty.
Locate the three dishwasher wires, (white, black and green)
with stripped ends. Insert dishwasher wires through the small
hole in the junction box "B".
Secure house wiring to the bottom of the junction box with a
strain relief "C".
[] Check to be sure power is OFF.
Use wire nuts to connect incoming ground to green, white to
white and black to black "D".
Replace junction box cover "E".Check to be sure that wires
[] Read the Owner's Manual for operating instructions.
are not pinched under the cover.
A
B Check That White, Block and
Green Dishwasher Wires Are Threaded
Remove
Junction
Cover
Box
_
Thru Hole in Buck
[] Open door and remove all foam and paper packaging.
[] Locate the Owner's Manual in the literature package.
[] Check door opening and closing. If door does not open and
close freelg or tends to foil, check spring adjustments. See
Step 1.
[] Check to be sure that wiring is secure under the dishwasher,
not pinched or in contact with door springs or other
components. See Step 9.
_
Ground
[] Check door alignment with tub. If door hits tub, level
I
dishwasher. See Step 10.
[] Pull lower rack out, about halfway. Check to be sure it does
not roll back or forward on the door. If the rack moves,
adjust leveling legs. See Step 10.
D UseULListed
Wire Nuts
[] Check door alignment with cabinet. If door hits cabinet,
C
Insert Power
Figure JJ
CordWires Thru
Strain Relief
and Tighten
reposition or relevel dishwasher. See Step 10.
[] Verifg water supplg ond drain lines ore not kinked or in
contact with other components. Contoct with motor or
dishwasher frame could cause noise. See Step 8.
[] Turn on the sink hot water faucet and verifg water
If house wiring is not 2-wire with ground, o
ground must be provided bg the installer.
When house wiring is aluminum, be sure to
use UL Listed anti-oxidant compound and
aluminum-to-copper connectors
temperature. Incoming water temperature must
be between 120°F and 150°F.A minimum of 120°F
temperature is required for best wash performance. See
"Prepare Hot Water Line," page 5.
[] Add 2 quarts of water to the bottom of the dishwasher to
lubricate the pump seal.
[] Turn on water supplg. Check for leaks. Tighten connections
if needed.
[] Remove protective film if present from the control panel
and door.
[] Avoid service cull charges bg ensuring there is on air gap
or drain hose routed through the required $2" minimum
height.
13
Installation
Instructions
STEP 16 DISHWASHER WET TEST
STEP 17 REPLACE TOEKICK
[] Turn on power supply (or plug power cord into outlet,
if equipped).
[] St(]rt the unit to check for le(]ks.
- Press ON/OFF button to turn unit on
- Press CYCLESELECTbutton until light below RINSEcycle
illumin(]tes
[] Close door.
[] Check to be sure th(]t w(]ter enters the dishw(]sher. If w(]ter
does not enter the dishw(]sher, check to be sure th(]t w(]ter
(]nd power (ire turned on.
[] Check for le(]ks under the dishw(]sher. If (] le(]k is found, turn
off power supply, then tighten connections. Restore power
(]ffer le(]k is corrected.
[] Check for le(]ks (]round the door. A le(]k (]round the door
could be c(]used by door rubbing or hitting (]g(]inst
(]dj(]cent c(]binet. Reposition the dishw(]sher if necess(]ry.
See Step 9.
[] The dishw(]sher will dr(]in (]nd turn off (]bout 5 to 7 minutes
(]ffer the first fill. Check dr(]in lines. If le(]ks (ire found,
turn power off (it the bre(]ker (]nd correct plumbing (is
necess(]ry. Restore power (]fter corrections (ire m(]de. See
Step 12.
[] Open dishw(]sher door (]nd m(]ke sure most of the w(]ter
h(]s dr(lined. If not, check th(]t disposer plug h(]s been
removed (]nd/or (]ir g(]p is not plugged. See Step 13. Also
check dr(]in line for kinking.
[]
Run the dishw(]sher through (]nother fill (]nd dr(]in cycle.
Check for le(]ks (]nd correct if required.
[] At the end of dr(]in, open door (]nd press ON/OFF button to
turn unit off.
Io
Screw Holes
UseTop4 _L
----_
............
Figure KK
• Place 2-piece toekick against the legs of the dishwasher.
• Pl(]ce the inner toekick piece (with slots) (]g(]inst the toekick
br(]cket. The slots should (]lign with toekick br(]cket screw
holes. Allow the toekick to touch the floor.
Pl(]ce I(]rger toekick over the inner piece (]nd inst(]ll 4 toekick
screws.
Use (]ddition(]l 2 screws for inst(]ll(]tions over 55-1/2" high.
Use both toekick pieces for (]11inst(]ll(]tion heights.
STEP 18 LITERATURE
,,Be sure to le(]ve complete liter(]ture p(]ck(]ge (]nd Inst(]ll(]tion
Instructions with the consumer.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
GE Consumer
General
Louisville,
& Industrial
Electric Compan U
Kentuck U 40225
monogram.com
© 2005 General
Electric Company
Pub. No. 31-30243
Dwg. No. 206C1559P181
ND 08C-2515 (4/08)