Delfield F1HR Installation manual

Delfield ColdPro Reach Ins
Service, Installation and Care Manual
Please read this manual completely before attempting to install or operate this equipment! Notify carrier of
damage! Inspect all components immediately. See page 2.
Refrigerators and Freezers
TION
A
M
R
O
T INF
N
A
T
R
O
USE
IMP
E
R
O
F
E
ONS!
I
T
C
READ B
U
R
INST
E
S
E
H
T
AVE
S
E
S
A
E
PL
Effective Date July 2005
ColdPro Service and Installation Manual
CONTENTS
RECEIVING & INSPECTING EQUIPMENT ................................. 2
SPECIFICATIONS........................................................................ 3
INSTALLATION .......................................................................... 4
OPERATION ................................................................................ 5
MAINTENANCE .......................................................................6-7
WIRING DIAGRAMS ...............................................................8-9
PARTS LISTING ................................................................. 10-13
STANDARD LABOR GUIDELINES ............................................14
WARRANTIES .................................................................... 15-16
©2005 The Delfield Company. All rights reserved. Reproduction without
written permission is prohibited. “Delfield” is a registered trademark of The
Delfield Company.
SERIAL NUMBER INFORMATION
The serial number of all self-contained refrigerators and
freezers is located inside the unit on the left hand side near
the top on the wall.
Always have the serial number of your unit available when
calling for parts or service. Please record your model and
serial number on the back cover of this manual for easy
reference.
This manual covers standard units only. If you have a custom
unit, consult the customer service department at the number
listed below.
RECEIVING AND INSPECTING THE EQUIPMENT
Even though most equipment is shipped crated, care should
be taken during unloading so the equipment is not damaged
while being moved into the building.
1.
2.
3.
2
Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.
If damaged, open and inspect the contents with the
carrier.
In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally
as well as in written form.
4.
5.
6.
7.
Request an inspection by the shipping company of the
damaged equipment. This should be done within 10
days from receipt of the equipment.
Be certain to check the compressor compartment
housing and visually inspect the refrigeration package.
Be sure lines are secure and base is still intact.
Freight carriers can supply the necessary damage forms
upon request.
Retain all crating material until an inspection has been
made or waived.
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
SPECIFICATIONS
COLDPRO SOLID DOOR REFRIGERATORS
MODEL #
R1FR
R1FL
R1HR
R1HL
R2FH
R2HH
R3FH
VOLTAGE
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
AMPS
5
5
5
5
9
9
11
STORAGE
CAPACITY FT3
18.7
18.7
18.7
18.7
40.25
40.25
61.8
SHELF
CAPACITY FT2
14.04
14.04
14.04
14.04
28.08
28.08
42.12
H.P.
1/4
1/4
1/4
1/4
1/2
1/2
1/2+
BTU
3200
3200
3200
3200
5800
5800
7625
CHARGE
21.2 oz.
21.2 oz.
21.2 oz.
21.2 oz.
30.0 oz.
30.0 oz.
37.0 oz.
SHIP
WEIGHT
332 LBS
332 LBS
332 LBS
332 LBS
498 LBS
498 LBS
649 LBS
NEMA
PLUG
5-15P
5-15P
5-15P
5-15P
5-15P
5-15P
5-15P
REFRIG.
TYPE
134A
134A
134A
134A
134A
134A
134A
SHELF
CAPACITY FT2
14.04
14.04
14.04
14.04
28.08
28.08
42.12
H.P.
1/2
1/2
1/2
1/2
3/4
3/4
1+
BTU
2325
2325
2325
2325
3650
3650
4500
CHARGE
19.4 oz.
19.4 oz.
19.4 oz.
19.4 oz.
20.5 oz.
20.5 oz.
28.2 oz.
SHIP
WEIGHT
334 LBS
334 LBS
334 LBS
334 LBS
558 LBS
558 LBS
766 LBS
NEMA
PLUG
5-15P
5-15P
5-15P
5-15P
5-15P
5-15P
5-20P
REFRIG.
TYPE
404A
404A
404A
404A
404A
404A
404A
COLDPRO SOLID DOOR FREEZERS
MODEL #
F1FR
F1FL
F1HR
F1HL
F2FH
F2HH
F3FH
3
VOLTAGE
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
AMPS
9
9
9
9
10
10
16
STORAGE
CAPACITY FT3
18.7
18.7
18.7
18.7
40.25
40.25
61.8
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
INSTALLATION
Location
Units represented in this manual are intended for indoor use
only. Be sure the location chosen has a floor strong enough
to support the total weight of the cabinet and contents. A fully
loaded unit can weigh as much as 4,000 pounds. Reinforce
the floor as necessary to provide for maximum loading. For
the most efficient refrigeration, be sure to provide good air
circulation inside and out.
Inside cabinet: Do not pack refrigerator so full that air
cannot circulate. The refrigerated air is discharged at the top
rear of the unit. It is important to allow for proper air flow
from the top rear to the bottom of the unit. Obstructions
to this air flow can cause evaporator coil freeze ups, loss of
temperature or overflow of water from the evaporator drain
pan. However, bags and other items can still be located to
the far rear of the cabinet. Air is
brought into the evaporator coil with
fans mounted to the front of the coil.
Prevent obstruction by locating large
boxes and tall stacks of product to
the bottom of the cabinet.
Unit repairs will not be subject to standard
unit warranties due to improper installation
procedures.
Electrical connection
Refer to the amperage data on page 3, the serial tag, your
local code or the National Electrical Code to be sure the unit is
connected to the proper power source. A protected circuit of
the correct voltage and amperage must be run for connection
of the line cord, or permanent connection to the unit.
The on/off switch must be turned to OFF and
the unit disconnected from the power source
whenever performing service, maintenance
functions or cleaning the refrigerated area.
Outside cabinet: Be sure that
the unit has access to ample air.
Avoid hot corners and locations
near stoves and ovens. It is
recommended that the unit be
installed no closer than 2” from any
wall.
Leveling
A level cabinet will not be subject to undue stress and perform
better when the doors line up with the frames properly. Use
a level to make sure the unit is level from front to back and
side to side. When the unit is supplied with casters, no
adjustments are available, but if unit comes with legs, they
have adjustable bullet feet. Ensure the floor where the unit is
to be located is level.
Stabilizing
Models are supplied on casters for your convenience, ease
of cleaning underneath and for mobility. It is very important,
however, that the cabinet be installed in a stable condition
with the front wheels locked while in use.
4
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
OPERATION
Do not throw items into the storage area.
Failure to follow these recommendations could
result in damage to the interior of the cabinet.
Temperature control instruction
Refrigerators: A thermostat located on the evaporator coil in
the interior of the unit, controls the temperature in the box.
The unit should maintain 38˚F(3˚C), with the factory control
setting at 5 or 6. Set toward “1” for warmer temperatures
and toward “7” for colder temperatures.
and turn power off to the evaporator fan motors.
1. Defrost Cycle, 20 minutes every 4 hours.
2. Anti-sweat heaters around each door opening operate
continually.
On/Off Switch:
An ON/OFF switch is located on the front of the evaporator coil
housing. When the unit is on, the switch will illuminate.
Freezers: A thermostat located on the evaporator coil in the
interior of the unit, controls the temperature in the box. The
unit should maintain -3˚F(-18˚C), with the factory control
setting at 6. Set toward “1” for warmer temperatures and
toward “7” for colder temperatures.
Refrigeration cycle
Refrigerators: The evaporator fans will run continuously
unless a door is open. The door switch will activate the
lights when opened and turn power off to the evaporator fan
motors.
1. The temperature control allows for the evaporator coil to
clear after each off cycle and before the compressor runs
again.
2. Anti-sweat heaters around each door opening operate
continually.
Freezers: The defrost timer supplies power to the temperature
control (for power to the condensing unit) and evaporator fan
motors. The door switch will activate the lights when opened
5
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
MAINTENANCE
The power switch must be turned to OFF and
the unit disconnected from the power source
whenever performing service, maintenance
functions or cleaning the refrigerated area.
Refrigerators and Freezers
The interior and exterior can be cleaned using soap and warm
water. If this isn’t sufficient, try ammonia and water or a nonabrasive liquid cleaner. When cleaning the exterior, always
rub with the “grain” of the stainless steel to avoid marring the
finish.
Do not use an abrasive cleaner because it will scratch the
stainless steel and can damage the breaker strips and gaskets.
Cleaning the Condenser Coil
The condenser coil requires regular cleaning, recommended
is every 90 days. In some instances though you may find
that there is a large amount of debris and dust or grease
accumulated prior to the 90 day time frame. In these cases the
condenser coil should be cleaned every 30 days.
If the build up on the coil consists of only light dust and debris
the condenser coil can be cleaned with a simple brush, heavier
dust build up may require a vacuum or even compressed air to
blow through the condenser coil.
If heavy grease is present there are de-greasing agents
available for refrigeration use and specifically for the condenser
coils. The condenser coil may require a spray with the degreasing agent and then blown through with compressed air.
Failure to maintain a clean condenser coil can initially cause
high temperatures and excessive run times, continuous
operation with dirty or clogged condenser coils can result in
compressor failures. Neglecting the condenser coil cleaning
procedures will void any warranties associated with the
compressor or cost to replace the compressor.
Never use a high pressure water wash for this
cleaning procedure as water can damage the
electrical components located near or at the
condenser coil.
Stainless Steel Care and Cleaning
To prevent discoloration of rust on stainless steel several
important steps need to be taken. First, we need to understand
the properties of stainless steel. Stainless steel contains 7080% iron which will rust. It also contains 12-30% chromium
which forms an invisible passive film over the steels surface
which acts as a shield against corrosion. As long as the
protective layer is intact, the metal is still stainless. If the film
is broken or contaminated, outside elements can begin to
breakdown the steel and begin to form rust of discoloration.
Proper cleaning of stainless steel requires soft cloths or plastic
scouring pads.
NEVER USE STEEL PADS, WIRE BRUSHES OR
SCRAPERS!
Cleaning solutions need to be alkaline based or non-chloride
cleaners. Any cleaner containing chlorides will damage
the protective film of the stainless steel. Chlorides are also
commonly found in hard water, salts, and household and
industrial cleaners. If cleaners containing chlorides are
used be sure to rinse repeatedly and dry thoroughly upon
completion.
Routine cleaning of stainless steel can be done with soap and
water. Extreme stains or grease should be cleaned with a
non-abrasive cleaner and plastic scrub pad. It is always good
to rub with the grain of the steel. There are also stainless steel
cleaners available which can restore and preserve the finish of
the steels protective layer.
Early signs of stainless steel breakdown can consist of small
pits and cracks. If this has begun, clean thoroughly and start
to apply stainless steel cleaners in attempt to restore the
passivity of the steel.
Never use an acid based cleaning solution!
Many food products have an acidic content
which can deteriorate the finish. Be sure to
clean the stainless steel surfaces of ALL food
products. Common items include, tomatoes,
peppers and other vegetables.
In order to maintain proper refrigeration performance, the
condenser fins must be cleaned of dust, dirt and grease
regularly. It is recommended that this be done at least every
three months. If conditions are such that the condenser is
totally blocked in three months, the frequency of cleaning
should be increased. Clean the condenser with a vacuum
cleaner or stiff brush. If extremely dirty, a commercially
available condenser cleaner may be required.
6
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
MAINTENANCE CONTINUED
If your freezer seems to vibrate excessively when
the compressor is running, loosen (but do not
remove) the bolts on the compressor.
MAINTENANCE
Gasket Maintenance
Gaskets require regular cleaning to prevent mold and mildew
build up and also to keep the elasticity of the gasket. Gasket
cleaning can be done with the use of warm soapy water. Avoid
full strength cleaning products on gaskets as this can cause
them to become brittle and prevent proper seals. Also, never
use sharp tools or knives to scrape or clean the gasket which
could possibly tear the gasket and rip the bellows.
Gaskets can easily be replaced and do not require the use of
tools or authorized service persons. The gaskets are “Dart”
style and can be pulled out of the grove in the door and new
gaskets can be “pressed” back into place.
Doors/Hinges
Over time and with heavy use doors the hinges may become
loose. If it is noticed that the door is beginning to sag, it may
become necessary to tighten the screws that mount the hinge
brackets to the frame of the unit. If the doors are loose or
sagging this can cause the hinge to pull out of the frame which
may damage both the doors and the door hinges. In some
cases this can require qualified service agents or maintenance
personnel.
Drain Maintenance
Each unit has a drain located inside the unit which removes
the condensation from the evaporator coil and evaporates it
at an external condensate evaporator pan. Each drain can
become loose or disconnected from moving or bumping the
drain. If you notice excessive water accumulation on the
inside of the unit be sure the drain tube is connected from
the evaporator housing to the condensate evaporator drain
pan. If water is collected underneath the unit you may want
to check the condensate evaporator drain tube to be sure it
is still located inside the drain pan. The leveling of the unit is
important as the units are designed to drain properly when
on a level surface, if your floor is not level this can also cause
drain problems. Be sure all drain lines are free of obstructions,
typically food product is found blocking drain lines causing
water to back up and overflow the drain pans.
7
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
WIRING DIAGRAMS: REFRIGERATORS
Models: R1FR, R1FL, R1HR, R1HL, R2FH, R2HH, R3FH
115 VOLT 60 CYCLE 1 PHASE
�
�
�
�����������
�����������
�����������
�����������
����
�����������������
�������������
8
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
WIRING DIAGRAMS: FREEZERS
�����������
�����������
����
�
�
�
��������������
�����������������
������� ����� ����� ����� ����
�������������������������
� �����������
�����������
�����������
����
�
�
�
� �����������
9
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
��������������
�����������������
������������� ����� ����
�������������������������
ColdPro Service and Installation Manual
REPLACEMENT PARTS
PART NUMBER
DESCRIPTION
UNIT TYPE
1 DR REF
3547699
CAPILLARY TUBE
3547700
CAPILLARY TUBE
3547701
CAPILLARY TUBE
3547702
CAPILLARY TUBE
3547703
CAPILLARY TUBE
3547704
CAPILLARY TUBE
3237524
CASTER, 4” DIAMETER
X
126-BXW-0030
CASTER/LEG BOTTOM CHANNEL
X
126-BXW-0031
CASTER/LEG BOTTOM CHANNEL
126-BXW-0032
CASTER/LEG BOTTOM CHANNEL
3526970
COMPRESSOR
3526971
COMPRESSOR
3526972
COMPRESSOR
3526973
COMPRESSOR
3526974
COMPRESSOR
3526975
COMPRESSOR
000-BXR-0030
CONDENSATE PAN ASSEMBLY (WITH HOT GAS LOOP)
000-BXR-0031
CONDENSATE PAN ASSEMBLY (WITH HOT GAS LOOP)
000-BXR-0032
CONDENSATE PAN ASSEMBLY (WITH HOT GAS LOOP)
127-BXV-0080
CONDENSATE PAN SLIDE
3516345
CONDENSER COIL
3516346
CONDENSER COIL
3516347
CONDENSER COIL
3516348
CONDENSER COIL
3516349
CONDENSER COIL
3516350
CONDENSER COIL
2162708
CONDENSER FAN MOTOR (INCLUDES BLADE & GUARD)
2162709
CONDENSER FAN MOTOR (INCLUDES BLADE & GUARD)
2162710
CONDENSER FAN MOTOR (INCLUDES BLADE & GUARD)
2162711
CONDENSER FAN MOTOR (INCLUDES BLADE & GUARD)
000-BXX-0030
CONDENSING UNIT PLATE & SLIDE ASSY
000-BXX-0031
CONDENSING UNIT PLATE & SLIDE ASSY
000-BXX-0032
CONDENSING UNIT PLATE & SLIDE ASSY
127-BXV-0070
CONDENSING UNIT/CONDENSATE SLIDE STOP BRACKET
2194674
DEFROST HEATER
2194675
DEFROST HEATER
2194676
DEFROST HEATER
2194712
DEFROST RELAY
3516337
DEFROST TIMER
127-BXV-0030
DEFROST TIMER BRACKET
2194677
DOOR LIGHT SWITCH
3 DR REF
1 DR FRZ
2 DR FRZ
3 DR FRZ
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
The installation of generic replacement parts will VOID warranty.
10
2 DR REF
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
X
X
X
X
X
X
X
X
X
X
X
X
X
ColdPro Service and Installation Manual
REPLACEMENT PARTS
PART NUMBER
DESCRIPTION
UNIT TYPE
1 DR REF
2 DR REF
3 DR REF
1 DR FRZ
2 DR FRZ
3 DR FRZ
3237521
DOOR LOCK
X
X
X
X
X
X
000-BBJ-0031
DOOR, HINGED LEFT, FULL SIZE
X
X
X
X
X
X
000-BBJ-0030
DOOR, HINGED RIGHT, FULL SIZE
X
X
X
X
X
X
000-BBJ-0033
DOOR, HINGED LEFT, HALF SIZE
X
X
X
X
000-BBJ-0032
DOOR, HINGED RIGHT, HALF SIZE
X
X
X
X
1702719
DRAIN
X
X
2194713
DRAIN HEATER, 5W FLEX
X
X
3516339
EVAPORATOR COIL
3516340
EVAPORATOR COIL
3516341
EVAPORATOR COIL
3516342
EVAPORATOR COIL
3516343
EVAPORATOR COIL
3516344
EVAPORATOR COIL
000-BXY-0030
EVAPORATOR COIL ASSY
000-BXY-0031
EVAPORATOR COIL ASSY
000-BXY-0032
EVAPORATOR COIL ASSY
000-BXY-0033
EVAPORATOR COIL ASSY
000-BXY-0034
EVAPORATOR COIL ASSY
000-BXY-0035
EVAPORATOR COIL ASSY
133-BXS-0030
EVAPORATOR COIL BOTTOM PANEL
133-BXS-0031
EVAPORATOR COIL BOTTOM PANEL
133-BXS-0032
EVAPORATOR COIL BOTTOM PANEL
133-BXS-0033
EVAPORATOR COIL BOTTOM PANEL
133-BXS-0034
EVAPORATOR COIL BOTTOM PANEL
133-BXS-0035
EVAPORATOR COIL BOTTOM PANEL
3516361
EVAPORATOR FAN GUARD
X
X
X
X
X
X
2162707
EVAPORATOR FAN MOTOR (INCLUDES BLADE)
X
X
X
X
X
X
133-BXU-0030
EVAPORATOR FAN MOUNTING PANEL
X
133-BXU-0031
EVAPORATOR FAN MOUNTING PANEL
133-BXU-0033
EVAPORATOR FAN MOUNTING PANEL
133-BXU-0032
EVAPORATOR FAN MOUNTING PANEL
3516354
EVAPORATOR HOUSING
3516355
EVAPORATOR HOUSING
3516356
EVAPORATOR HOUSING
3516357
EVAPORATOR HOUSING
3516358
EVAPORATOR HOUSING
3516359
EVAPORATOR HOUSING
1701338
GASKET, FULL DOOR
X
X
1701339
GASKET, HALF DOOR
X
X
2194712
2194711
3237528
HINGE CARTRIDGE, SELF CLOSING
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
HIGH PRESSURE CUTOUT RELAY
X
X
X
HIGH PRESSURE CUTOUT SWITCH
X
X
X
X
X
X
X
The installation of generic replacement parts will VOID warranty.
11
X
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
X
X
X
X
ColdPro Service and Installation Manual
REPLACEMENT PARTS
PART NUMBER
DESCRIPTION
UNIT TYPE
1 DR REF
2 DR REF
3 DR REF
1 DR FRZ
2 DR FRZ
3 DR FRZ
3237529
HINGE PIN SLEEVE
X
X
X
X
X
X
3237519
HINGE, BOTTOM LEFT
X
X
X
X
X
X
3237526
HINGE, BOTTOM RIGHT
X
X
X
X
X
X
3237518
HINGE, TOP LEFT
X
X
X
X
X
X
3237525
HINGE, TOP RIGHT
X
X
X
X
X
X
3237520
HINGE, MIDDLE LEFT (HALF DOOR ONLY)
X
X
X
X
3237527
HINGE, MIDDLE RIGHT (HALF DOOR ONLY)
X
X
X
X
3237523
LEG, 6”
X
X
X
X
X
X
2194686
LIGHT BULB
X
X
X
X
X
X
2194682
LIGHT FIXTURE
X
X
X
X
X
X
3237522
LOCK KEY
X
X
X
X
X
X
3234861
LOCK STRIKE
X
X
X
X
X
X
2194683
ON/OFF SWITCH
X
X
X
X
X
2194691
ON/OFF SWITCH
2194684
POWER CORD, 14GA
X
X
X
X
X
2194685
POWER CORD, 16GA
129-BEJ-0030
REAR MACHINE COMPARTMENT COVER
129-BEJ-0031
REAR MACHINE COMPARTMENT COVER
129-BEJ-0032
REAR MACHINE COMPARTMENT COVER
3978195
SHELF
3978207
SHELF
3978198
SHELF, LEFT
3978209
SHELF, LEFT
3978206
SHELF, MIDDLE
3978208
SHELF, MIDDLE
3978199
SHELF, RIGHT
3978210
SHELF, RIGHT
3234859
SHELF PILASTER STRIP
X
X
X
9321587
THUMB SCREWS FOR PILASTER STRIP
X
X
3234860
SHELF CLIP
X
X
3234868
SHROUD HINGE
X
3234891
SHROUD HINGE
X
X
000-BBM-0033
BOTTOM SHROUD HINGED LEFT
X
000-BBM-0030
BOTTOM SHROUD HINGED RIGHT
X
000-BBM-0031
BOTTOM SHROUD
000-BBM-0032
BOTTOM SHROUD
000-BBK-0033
TOP SHROUD HINGED LEFT
X
X
000-BBK-0030
TOP SHROUD HINGED RIGHT
X
X
000-BBK-0031
TOP SHROUD
000-BBK-0032
TOP SHROUD
127-BXV-0050
TOP SHROUD CLOSURE BRACKET
X
X
X
X
X
X
127-BXV-0060
TOP SHROUD MOUNTING BRACKET
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
The installation of generic replacement parts will VOID warranty.
12
X
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
X
ColdPro Service and Installation Manual
REPLACEMENT PARTS
PART NUMBER
DESCRIPTION
UNIT TYPE
1 DR REF
2 DR REF
3 DR REF
X
X
X
1 DR FRZ
2 DR FRZ
3 DR FRZ
X
X
X
123-BEI-0030
SUCTION LINE COVER
123-BEI-0031
SUCTION LINE COVER
3516338
THERMOMETER
X
X
X
X
X
X
9321593
THERMOMETER BULB CLIP
X
X
X
X
X
X
127-BXV-0040
THERMOMETER TRANSFORMER BRACKET
X
X
X
X
X
X
2194673
THERMOSTAT
X
X
X
3516336
THERMOSTAT
X
X
X
MODEL
START RELAY MANUFACTURER AND MODEL (OR EQUIVALENT)
START CAPACITOR RATING (uF)
START CAPACITOR VOLTAGE RATING (VAC)
RUN CAPACITOR RATING (uF)
1 DR REF
2 DR REF
3 DR REF
1 DR FRZ
2 DR FRZ
3 DR FRZ
ELECTRICA
MTRP 5508
W343
ELECTRICA
MTRP
H0016
-08W343
KLIXON
9660-302719109
Z3L
KLIXON
9660C-041191 21 V2L
GENERAL
ELECTRIC
3ARR383F3
GENERAL
ELECTRIC
3ARR3B3S3
145-174
189-227
189-227
145-175
145-174
340-408
165
165
330
250
165
165
NONE USED
NONE USED
NONE USED
NONE USED
25 ± 5%
20 ± 5%
MISC. ITEMS
DESCRIPTION
SPEC.
TOP SHROUD COVER HOLD DOWN SCREW
M4, 16MM LONG (NICKEL GALVANIZED)
TOP SHROUD HINGE SCREW & NUTS
M4, 16MM LONG (STAINLESS STEEL), M4 NUT (STAINLESS STEEL)
M4, 10MM LONG (ZINC GALVANIZED)
CABINET HINGE MOUNTING SCREW
M6, 20MM LONG (STAINLESS STEEL)
LOWER SHROUD MOUNTING SCREW
M4, 10MM LONG (ZINC GALVANIZED)
REAR MACHINE COMPARTMENT MOUNTING SCREW
M5, 20MM LONG (ZINC GALVANIZED)
HINGE CARTRIDGE MOUNTING SCREW
M5, 20MM LONG (STAINLESS STEEL)
HINGE CARTRIDGE PIN SCREW
M5, 10MM LONG (STAINLESS STEEL)
EVAPORATOR HOUSING MOUNTING SCREW
M4, 16MM LONG (STAINLESS STEEL)
EVAPORATOR FAN GUARD MOUNTING SCREW
M5, 10MM LONG (STAINLESS STEEL), M5 NUT (STAINLESS STEEL)
EVAPORATOR FAN MOTOR MOUNTING SCREW
M4, 16MM LONG (STAINLESS STEEL), M4 NUT (STAINLESS STEEL)
REFRIGERATOR VINYL DRAIN TUBE
0.625 OD, 0.5O ID
FREEZER VINYL DRAIN TUBE
0.375 OD, 0.25 ID
The installation of generic replacement parts will VOID warranty.
13
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
STANDARD LABOR GUIDELINES TO REPAIR OR REPLACE PARTS ON DELFIELD EQUIPMENT
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
• A maximum of 1-hour is allowed to diagnose a defective component.
• A maximum of 1-hour is allowed for retrieval of parts not in stock.
• A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed.
• Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or
correcting and end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work
Authorization from Delfield. You must submit the number with the service claim.
LABOR OF 1-HOUR IS ALLOWED TO REPLACE:
• Thermostat
• Door Jamb Switch
• Hi-limit/Thermal Protector Switch
• Fan Delay/Defrost Termination Switch
• Compressor Start Components and Overload Protector
• Thermometer
•
•
•
•
•
Contactor/Relay
Evaporator/Condenser Fan Motor and Blade
Door Hinges, Locks, and Gaskets
Condensate Element
Defrost Timer
LABOR OF 2 HOURS TO REPLACE:
• Defrost Element
• Pressure Switch
• Locate/Repair Leak
LABOR OF 3 HOURS TO REPLACE:
• Capillary Tube
• Condenser or Evaporator Coil
LABOR OF 4 HOURS TO REPLACE
• Compressor
This includes recovery of refrigerant and leak check.
$35.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings,
solder, brazing rod, nitrogen, or similar fees.)
REFRIGERANTS
• R134A A maximum of $5.00/lb. or 31¢/oz. will be reimbursed.
• R404A A maximum of $12.00/lb. or 75¢/oz. will be reimbursed.
14
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
STANDARD ONE YEAR WARRANTY (ONE YEAR PARTS AND LABOR.)
The Delfield Company (“Delfield”) warrants to the Original Purchaser
of the Delfield product (herein called the “Unit”) that such Unit, and all
parts thereof, will be free from defects in material and workmanship
under normal use and service for a period of one (1) year from
the date of shipment of the Unit to the Original Purchaser or, if the
Original Purchaser returns the warranty card completely filled out
including the date of installation within thirty (30) days of receipt
of the Unit, one (1) year from the date of installation. During this
one year warranty period, Delfield will repair or replace any defective
part or portion there of returned to Delfield by the Original Purchaser
which Delfield determines was defective due to faulty material or
workmanship. The Original purchaser will pay all labor, crating, freight
and related costs incurred in the removal of the Unit of defective
component and shipment to Delfield, except that during a period of
either ninety (90) days from the date of shipment of the Unit to the
Original Purchaser or, if the Original Purchaser returns the warranty
card completely filled out including the date of installation within thirty
(30) days of receipt of the Unit, ninety (90) days from the date of
installation Delfield will pay all related labor costs. Delfield will pay the
return costs if the Unit or part thereof was defective.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
This warranty does not apply to any Unit or part thereof that has
been subjected to misuse, neglect, alteration, or accident, such as
accidental damage to the exterior finish, operated contrary to the
recommendations specified by Delfield; or repaired or altered by anyone
other than Delfield in any way so as to, in Delfield’s sole judgement,
affect its quality or efficiency. This warranty does not apply to any Unit
that has been moved from the location where it was originally installed.
This warranty also does not cover the refrigerator drier or the light
bulbs used in the Unit. The warranty is subject to the user’s normal
maintenance and care responsibility as set forth in the Service and
Installation Manual, such as cleaning the condenser coil, and is in
lieu of all other obligations of Delfield. Delfield neither assumes, nor
authorizes any other person to assume for Delfield, any other liability
in connection with Delfield’s products.
Removal or defacement of the original Serial Number or Model Number
from any Unit shall be deemed to release Delfield from all obligations
hereunder or any other obligations, express or implied.
Parts furnished by suppliers to Delfield are guaranteed by Delfield only
to the extent of the original manufacturer’s express warranty to Delfield.
Failure of the Original Purchaser to receive such manufacturer’s express
warranty to Delfield. Failure of the Original Purchaser to receive such
manufacturers warranty shall in no way create any warranty, expressed
or implied, or any other obligation or liability on Delfield’s part in respect
thereof.
IF THE CUSTOMER IS USING A PART THAT RESULTS IN A VOIDED
WARRANTY AND A DELFIELD AUTHORIZED REPRESENTATIVE
TRAVELS TO THE INSTALLATION ADDRESS TO PERFORM WARRANTY
SERVICE, THE SERVICE REPRESENTATIVE WILL ADVISE CUSTOMER
THE WARRANTY IS VOID. SUCH SERVICE CALLS WILL BE BILLED
TO CUSTOMER AT THE AUTHORIZED SERVICE CENTER’S THEN
APPLICABLE TIME AND MATERIALS RATES. CONSIDER: CUSTOMER
MAY INITIATE A SERVICE AGREEMENT WITHOUT PARTS COVERAGE.
If shipment of a replacement part is requested prior to the arrival in
the Delfield factory of the part claimed to be defective, the Original
Purchaser must accept delivery of the replacement part of a C.O.D.
15
basis, with credit being issued after the part has been received and
inspected at Delfield’s plant and determined by Delfield to be within this
warranty.
Under no condition does this warranty give the Original Purchaser the
right to replace the defective Unit with a complete Unit of the same
manufacturer or of another make. Unless authorized by Delfield in
writing, this warranty does not permit the replacement of any part,
including the motor-compressor, to be made with the part of another
make or manufacturer.
No claims can be made under this warranty for spoilage of any products
for any reason, including system failure.
The installation contractor shall be responsible for building access,
entrance and field conditions to insure sufficient clearance to allow any
hood(s), vent(s), or Unit(s) if necessary, to be brought into the building.
Delfield will not be responsible for structural changes or damages
incurred during installation of the Unit or any exhaust system.
Delfield shall not be liable in any manner for any default or delay in
performance hereunder caused by or resulting from any contingency
beyond Delfield’s control, including, but not limited to, war,
governmental restrictions or restraints, strike, lockouts, injunctions,
fire, flood, acts of nature, short or reduced supply of raw materials, or
discontinuance of the parts by the original part manufacturer.
Except as provided in any Additional Service Labor Contract,
if applicable, the foregoing is exclusive and in lieu of all other
warranties, whether written or oral, express or implied. This
warranty supersedes and excludes any prior oral or written
representations or warranties. Delfield expressly disclaims any
implied warranties of merchantability, fitness for a particular purpose
of compliance with any law, treaty, rule or regulation relating to
the discharge of substances into the environment. The sole and
exclusive remedies of any person relating to the Unit, and the
full liability of Delfield for any breach of this warranty, will be as
provided in this warranty.
Other than this Delfield Standard One Year Limited Warranty, any
applicable Delfield Additional Four Year Protection Plan or applicable
Delfield Service Labor Contract, the Original Purchaser agrees and
acknowledges that no other warranties are offered or provided in
connection with or for the unit or any other part thereof.
In no event will Delfield be liable for special, incidental or consequential
damages, or for damages in the nature of penalties.
IF DURING THE WARRANTY PERIOD, CUSTOMER USES A PART FOR
THIS DELFIELD EQUIPMENT OTHER THAN AN UNMODIFIED NEW
OR RECYCLED PART PURCHASED DIRECTLY FROM DELFIELD OR
ANY OF ITS AUTHORIZED SERVICE CENTERS AND/OR THE PART
BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION,
THIS WARRANTY WILL BE VOID. FURTHER, DELFIELD AND ITS
AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS DAMAGES OR
EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE DIRECTLY
OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION
OF ANY MODIFIED PART AND/OR PART RECEIVED FROM AN
UNAUTHORIZED SERVICE CENTER. If the warranty becomes void,
Customer may purchase from Delfield, if available, a Service
Agreement or service at the then current time and materials rate.
For more information on Delfield warranty’s log on and check out the
service section of our web site at www.delfield.com.
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
ADDITIONAL FOUR YEAR PROTECTION PLAN (FOR MOTOR-COMPRESSORS ONLY)
In addition to the Standard One Year Warranty on the MotorCompressor contained in the above listed Delfield product
(the “Unit”), The Delfield Company (“Delfield”) also agrees to
repair, or exchange with similar or interchangeable parts in
design and capacity at Delfield’s option, the defective MotorCompressor contained in the Unit (the “Motor-Compressor),
or any part thereof, for the Original Purchaser only, at any
time during the four (4) years following the initial one (1) year
period commencing on the date of installation for the Original
Purchaser. Failure of the Original Purchaser to register
the registration card containing the Original Purchasers
name, address, date of installation, model number and
serial number of the Unit containing the Motor-Compressor within 30 days from the date of installation shall void
this warranty. This additional warranty is only available if the
Motor-Compressor is inoperative due to defects in material
or factory workmanship, as determined by Delfield in its sole
judgement and discretion. The Original Purchaser shall be
responsible for returning the defective Motor-Compressor to
Delfield prepaid, F.O.B. at the address shown on the back
cover of this manual.
The term “Original Purchaser” as used herein means that
person, firm, association, or corporation for whom the Unit was
originally installed.
The term “Motor-Compressor” as used herein does not include
unit base, air or water cooled condenser, receiver, electrical
accessories such as relay, capacitors, refrigerant controls, or
condenser fan/motor assembly. This warranty does not cover
labor charges incidental to the replacement of parts. This
warranty further does not include any equipment to which said
condensing unit is connected, such as cooling coils, temperature controls or refrigerant metering devices. This warranty
shall be void if the Motor-Compressor, in Delfield’s sole judgement, has been subjected to misuse, neglect, alteration or
accident, operated contrary to the recommendations specified
by the Unit manufacturer, repaired or altered by anyone other
than Delfield in any way so as, in Delfield’s sole judgment, to
affect its quality or efficiency or if the serial number has been
altered, defaced or removed. This Warranty does not apply
to a Motor-Compressor in any Unit that has been moved from
the location where it was originally installed. The addition of
methyl chloride to the condensing unit or refrigeration system
shall void this warranty.
General Conditions
Delfield shall not be liable in any manner for any default or
delay in performance hereunder caused by or resulting form
any contingency beyond Delfield’s control, including, but
not limited to, war, governmental restrictions or restrains,
strike, lockouts, injunctions, fire, flood, acts of nature, short or
reduced supply of raw materials, or discontinuance of any part
or the Motor-Compressor by the unit manufacturer.
Replacement of a defective Motor-Compressor is limited to
one (1) Motor-Compressor by us during the four (4) year
period. Delfield shall replace the Motor-Compressor at no
charge.
This warranty does not give the Original Purchaser of the
Motor-Compressor the right to purchase a complete replacement Motor-Compressor of the same make or of another
make. It further does not permit the replacement to be made
with a Motor-Compressor of another kind unless authorized by
Delfield. In the event Delfield authorizes the Original Purchaser to purchase a replacement Motor-Copmressor locally,
only the wholesale cost of the Motor-Compressor is refundable.
Expressly excluded from this warranty are damages resulting
from spoilage of goods.
Except as provided in any applicable Standard One Year
Limited Warranty or applicable Service Labor Contract,
the foregoing is exclusive and in lieu of all other warranties, whether written or oral, express or implied. This
Warranty supersedes and excludes any prior oral or
written representations or warranties. Delfield expressly
disclaims any implied warranties of merchantability, fitness for a particular purpose or compliance with any law,
treaty, rule or regulation relating to the Motor-Compressor, and the full liability of Delfield for any breach of this
warranty, will be as provided in this warranty.
Other than any applicable Delfield Standard One year Limited
Warranty, this Delfield Additional Four Year Protection Plan
and any applicable Delfield Service Labor Contract, the
Original Purchaser agrees and acknowledges that no other
warranties are offered or provided in connection with or for the
Motor-compressor or any part thereof.
In no event will Delfield be liable for special, incidental or consequential damages, or for damages in the nature of penalties.
16
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
NOTES:
17
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
NOTES:
18
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
ColdPro Service and Installation Manual
NOTES:
19
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
��
�
�
�
��
��
��
�
�
Mt. Pleasant, MI
�
�
� ��
��
��
Covington,
TN
�
�
��
Thank you for choosing Delfield!
����������������������
Help is a phone call������������������������������������
away. Help our team of ���������������������������������
professional, courteous customer
service
�����������������������
����������������
�����������������
���������������������
reps by having your
model number and serial
number available at the�����������������
time
����������������������
�����������������
�������������������
������������
������������
������������
������������
of your call (800) 733-8829
������������
������������
������������
������������
�����������������������
����������������
���������������������������������
����������������
����������������
������������������������������
�������������������������������
��������������������������
�����������������
������������������������������
���������������������������
Model: ___________________S/N:
_____________________________
��������������������������������
���������������������������������
����������������
���������������
�����������������������
��������������������
������������
������������
����������������
���������������������������
�������������������
������������
������������
����������������
���������������
������������
�������������������������
������������
����������������
������������������������������
�����������������������
��������������������������
Installation Date: __________________
����������������
���������������������������
������������
����������������
��������������
��������������������������
����������������������������
���������������������������������
����������������������
���������������
������������
����������������
���������������
�������������������
������������
����������������
�������������������������
��������������������������������������
�������������������
����������
������������������
������������
������������
����������������
��������������������������������
������������������
������������
����������������
������������������������������
�������������������
����������������
������������
������������
����������������
������������������������������
For a list of Delfield’s authorized parts depots,
visit�������������������������������
our website at
����������������������������
����������
������������������
��������������������
����������������
www.delfi
eld.com
���������������������
��������������������
�������������������
����������������������
��������������������������������������
�����������������������������������
������������
������������
����������������
������������
����������������
������������
����������������
��������������������������
�������������������������������
������������������������������
��������������
�������������������������������������������������������������������������������������������������������������������������������
����������������������������������������������������������������������������������������������������������������������������������������������������������������������
DMCOLDPRO 07/05