DTS DELTA R FULL COLOR User`s manual

DELTA R
DELTA R FULL COLOR
DELTA R TRILED
DELTA 5-7 RGB R
GB
User’s Manual Rel 1.5
D.T.S. Illuminazione srl - ITALY
http://www.dts-lighting.it
Made in Italy
2
DELTA R
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de D.T.S.
D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. D.T.S. décline toute responsabilité sur l'utilisation ou
sur l'application des produits ou des circuits décrits.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
o reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.
D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume responsabilidad de
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
DELTA R
3
INDEX:
1- TECHNICAL FEATURES
2- IMPORTANT SAFETY INFORMATION
4
8
2.1 Fire prevention
2.2 Prevention of electric shock
2.3 Protection against direct light radiation
2.4 Safety
2.5 Level of protection against the penetration of solid and liquid matter
3- VOLTAGE AND FREQUENCY
4- INSTALLATION
9
9
4.1 Safety cable
4.2 Risk of fire
4.3 Ambient temperature
5- MAINS CONNECTION
10
5.1 Protection:
6- DMX SIGNAL CONNECTION
10
6.1 DMX Addresses
6.2 Selecting the DMX address
7- MOVEMENT
8- DISPLAY FUNCTIONS
11
12
9- OPENING UP THE PROJECTOR HOUSING
25
9.1 Arms
9.2 base
10- CHANGHING THE LENSES
11- PERIODIC CLEANING
12- PERIODIC CONTROLS
13- DMX PROTOCOL
26
28
29
4
DELTA R
1- TECHNICAL FEATURES
Delta R Full Color
40 RGB Full Color LEDs/ LED power 3W
2.800 Lumens / 370 Lux at 5 m (medium flood lenses)
RGB color generation / 16 million colours
Colour temperature variable on a linear range (3.200°K÷5.500°K)
No infrared emission / no ultraviolet emission
LEDs average lifespan: 100.000 hours
Optical units can be interchanged by users (spot / medium /wide)
Interface: OLED display + 4 buttons / infrared remote control
Control signals: USITT DMX 512 USITT serial digital signals
15 DMX channels
Independent operation (Master / Slave)
Programmable automated playback (7 days)
Movement on 3 axes : Pan 320° /Tilt1 160°(Motorized) / Tilt2 135°(Manual).
Safety-locking system
IP65 protection level
Professional HARTING / ILME sockets (IP65 protection rating)
Full range AC 90-260V, 50-60Hz power supply
Operating ambient temperature -10° / 40°
Weight: 24 Kg
ACCESSORIES
Lenses set spot (cod. 03.LK.008)
Lenses set medium flood (cod. 03.LK.001)
Lenses set wide flood (cod. 03.LK.002)
Flight case for 1 DELTA (cod. 0521C029)
Flight case for 2 DELTA (cod. 0521C030)
Safety wire (3mm x 60 cm), Ring spring catch (max. capacity load 60Kg) (Cod. 0521A010)
“C” Clamp GQUICK with “Fast Lock” connection ¼ turn (max. load 80Kg) (cod. 0521A014)
Dimensions (LxDxH)
projector 430 x 285 x 570 mm
Packaging Dimensions (LxDxH)
530 x 500 x 660 mm
Weight24 Kg (motorized version)
Weight 30 Kg (motorized version)
5
DELTA R
Delta R Triled
20 LEDs / TRILED technology / LED power 1W x 3
2.400 Lumens / 450 Lux at 5 m (medium flood lenses)
RGB color generation / 16 million colours
Colour temperature variable on a linear range (3.200°K÷5.500°K)
No infrared emission / no ultraviolet emission
LEDs average lifespan: 100.000 hours
Optical units can be interchanged by users (spot / medium flood / wide flood)
Interface: OLED display + 4 buttons / infrared remote control
Control signals: USITT DMX 512 USITT serial digital signals
15 DMX channels
Independent operation (Master / Slave)
Programmable automated playback (7 days)
Movement on 3 axes : Pan 320° /Tilt1 160°(Motorized) / Tilt2 135°(Manual)
Safety-locking system
IP65 protection level
Professional HARTING / ILME sockets (IP65 protection rating)
Full range AC 90-260V, 50-60Hz power supply
Operating ambient temperature -10° / 40°
Weight: 24 Kg
ACCESSORIES
Lenses set spot (cod. 03.LK.004)
Lenses set medium flood (cod. 03.LK.005)
Lenses set wide flood (cod. 03.LK.006)
Flight case for 1 DELTA (cod. 0521C029)
Flight case for 2 DELTA (cod. 0521C030)
Safety wire (3mm x 60 cm), Ring spring catch (max. capacity load 60Kg) (Cod. 0521A010)
“C” Clamp GQUICK with “Fast Lock” connection ¼ turn (max. load 80Kg) (cod. 0521A014)
Dimensions (LxDxH)
projector 430 x 285 x 570 mm
Packaging Dimensions (LxDxH)
530 x 500 x 660 mm
Weight24 Kg (motorized version)
Weight 30 Kg (motorized version)
6
DELTA R
1- TECHNICAL FEATURES
Delta 5 RGB R
108 X 1W Luxeon type LEDS (36 Red, 36 Green, 36 Blue)
2.400 Lumens / 900 Lux at 5 m (medium flood lenses)
RGB color generation / 16 million colours
Colour temperature variable on a linear range (3.200°K÷5.500°K)
No infrared emission / no ultraviolet emission
LEDs average lifespan: 100.000 hours
Optical units can be interchanged by users (spot / medium /wide)
Interface: OLED display + 4 buttons / infrared remote control
Control signals: USITT DMX 512 USITT serial digital signals
15 DMX channels
Independent operation (Master / Slave)
Programmable automated playback (7 days)
Movement on 3 axes : Pan 320° /Tilt1 160°(Motorized) / Tilt2 135°(Manual).
Safety-locking system
IP65 protection level
Professional HARTING / ILME sockets (IP65 protection rating)
Full range AC 90-260V, 50-60Hz power supply
Operating ambient temperature -10° / 40°
Weight: 24 Kg
ACCESSORIES
Lenses set spot (cod. 03.LK.008)
Lenses set medium flood (cod. 03.LK.001)
Lenses set wide flood (cod. 03.LK.002)
Flight case for 1 DELTA (cod. 0521C029)
Flight case for 2 DELTA (cod. 0521C030)
Safety wire (3mm x 60 cm), Ring spring catch (max. capacity load 60Kg) (Cod. 0521A010)
“C” Clamp GQUICK with “Fast Lock” connection ¼ turn (max. load 80Kg) (cod. 0521A014)
Dimensions (LxDxH)
projector 430 x 285 x 570 mm
Packaging Dimensions (LxDxH)
530 x 500 x 660 mm
Weight24 Kg (motorized version)
Weight 30 Kg (motorized version)
7
DELTA R
1- TECHNICAL FEATURES
Delta 7 RGB R
108 X 1W P4 type LEDS (36 Red, 36 Green, 36 Blue)
2.400 Lumens / 1150 Lux at 5 m (medium flood lenses)
RGB color generation / 16 million colours
Colour temperature variable on a linear range (3.200°K÷5.500°K)
No infrared emission / no ultraviolet emission
LEDs average lifespan: 100.000 hours
Optical units can be interchanged by users (spot / medium /wide)
Interface: OLED display + 4 buttons / infrared remote control
Control signals: USITT DMX 512 USITT serial digital signals
15 DMX channels
Independent operation (Master / Slave)
Programmable automated playback (7 days)
Movement on 3 axes : Pan 320° /Tilt1 160°(Motorized) / Tilt2 135°(Manual).
Safety-locking system
IP65 protection level
Professional HARTING / ILME sockets (IP65 protection rating)
Full range AC 90-260V, 50-60Hz power supply
Operating ambient temperature -10° / 40°
Weight: 24 Kg
ACCESSORIES
Lenses set spot (cod. 03.LK.008)
Lenses set medium flood (cod. 03.LK.001)
Lenses set wide flood (cod. 03.LK.002)
Flight case for 1 DELTA (cod. 0521C029)
Flight case for 2 DELTA (cod. 0521C030)
Safety wire (3mm x 60 cm), Ring spring catch (max. capacity load 60Kg) (Cod. 0521A010)
“C” Clamp GQUICK with “Fast Lock” connection ¼ turn (max. load 80Kg) (cod. 0521A014)
Dimensions (LxDxH)
projector 430 x 285 x 570 mm
Packaging Dimensions (LxDxH)
530 x 500 x 660 mm
Weight24 Kg (motorized version)
Weight 30 Kg (motorized version)
8
DELTA R
2- IMPORTANT SAFETY INFORMATION
2.1 Fire prevention:
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 m.
-Minimum distance from the closest illuminable surface: 1 m.
-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if
there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
2.2 Prevention of electric shock:
-High voltage is present inside the unit. Isolate the projector from the mains supply prior to performing
any function which involves touching the inside of the unit.
-The level of technology inherent in the DELTA R requires the assistance of specialised personnel for all
servicing.Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
2.3 Protection against direct light radiation:
-Never turn the unit on if any of the lenses or the glass lenses protection is damaged.
-Never look directly the leds when they are on.
2.4 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety chain to sustain the weight of the unit in case of the failure of the main
fixing point.
-The external surface of the unit, at various points, may exceed 80°C. Never handle the unit until it’s on.
-Never install the fixture in an enclosed area lacking sufficient air flow.
-The ambient temperature should not exceed 40°C.
2.5 Level of protection against the penetration of solid and liquid matter:
-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid matter is IP 65.
9
DELTA R
.
3- VOLTAGE AND FREQUENCY:
Delta R can operate at 90-270V, 50 or 60 Hz.
4- INSTALLATION:
Delta R may be either floor or ceiling mounted.
For floor mounting installations, the unit is supplied with four rubber mounting feet on the base.
For ceiling mounted installations, we reccommend the use of appropriate clamps to fix the unit to the
mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the
unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to
move or shake whilst the Delta R is moving.
The Delta R is fitted with 4 fixing points on the bottom used to attach accessories (clamps, hooks, etc.)
With a fast lock closure/release system (1/4 turn) to fix the fixture in any position.
.
4.1 Safety cable:
We recommend the use of a safety cable or chain connected to the Delta R and to the suspension truss
in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron
cable or chain can bear the weight of the entire unit.
You may attach the safety chain to the holes located on the base of the fixture, as shown in the picture
below.
SAFETY CABLE
FIXING POINT
4.2 Risk of fire:
Each fixture produces heat and must be installed in a well-ventilated position. The minimum
recommended distance from flammable material is 1m. Minimum distance from the object being
illuminated is 1 m.
DELTA R
10
4.3 Ambient temperature:
The projector should never be installed in places that lack a constant air flow. The ambient temperature
should NOT exceed 40°C.
5- MAINS CONNECTION:
Delta R can operate at 90-270V, 50 or 60Hz.
For connection purposes, ensure that your plug can handle at least 300W power consuption.
Strict adherence to regulatory norms is strongly
Recommended.
MAINS
Electronic ballast
90-260V 50 / 60Hz
FUSE: T 3,15A
5.1 Protection:
4
1
3
2
The use of a thermal magnetic circuit breaker is recommended for each Delta R.
A good earth connection is essential for the correct operation of the projector.
6- DMX SIGNAL CONNECTION:
The unit operates using a digital DMX 512 (1990) signal. Connection between the control box and the
projector or between projectors must be carried out using a two pair screened ø0.5 mm cable and a
CANNON XLR 5 or 3 pole connector.
Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR chassy
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect
it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the
second one.
In this way, all the projectors are cascade connected.
CONTROLLER
STANDARD
DMX 512
5
1
4
2
DMX IN
1=GND
2=DATA3=DATA+
DMX OUT
3
OUT
IN
OUT
IN
OUT
IN
P.S:
If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX reception problem
OUT
DELTA R
11
6.1 DMX Addresses:
DELTA R have 15 DMX control channels.
Here below are described the DMX channels addressing for the controller:
Projector
Projector
Projector
…..
projector
1
2
3
6
A001
A016 If you want to select the next projector, just add “15”
A031
A….
A091
6.2 Selelcting the DMX address:
1) Press the UP-DOWN key until you reach the required DMX address. The numbers on the display will
start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now controlled by the new DMX address.
TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get
a faster selection.
MENU
ENTER
UP
DOWN
7- Movement
The projector has a maximum movement of 320° for Pan,180° for Tilt 1 and 135° for tilt 2
(7 mechanical steps 22,5° each).
DO NOT place any obstructions in the path of the projector's movement.
PAN 320°
Tilt 2 mechanical regulation
TILT1 180°
Motorized
TILT2 135°
Mechanical
DELTA R
12
8- DISPLAY FUNCTIONS
DISPLAY FUNCTIONS
The DELTA R display panel shows all the available functions . Using these functions, it is possible
to change some of the parameters and add some functions. Changing the DTS setting can vary the
functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully
follow the instructions below before carrying out any variations or selections.
DELTA SOFTWARE RELEASE 1.72
1)GLOBAL SETTING MENU
4)LED SETUP MENU
LANGUAGE
DEFAULT PAGE
SECURITY
DEFAULT SETTING
SET DATE
SET TIME
UPDATE
DOWNLOAD
ABOUT
COLOUR MODE
WHITE BALANCE
BOOST DRIVING
MIN RGB
MAX RGB
SMOOT FILTER
PWM FREQUENCY
2)MODE SETTING MENU
MODE
MODE
MODE
MODE
MODE
MODE
MODE
DMX
RECORDER
MASTER
SLAVE
IR
MANUAL
TWILIGHT
3)MOVING HEAD SETUP MENU
PAN MIN
PAN MAX
TILT MIN
TILT MAX
CALIBRATE PAN
CALIBRATE TILT
INVERT PAN
INVERT TILT
SWAP PAN & TILT
ENCODER
RESET PAN & TILT
SPEED PAN & TILT
5)DIPLAY SETTINGS MENU
CONTRAST
FLIP DISPLAY
SCREEN SAVER
6)MEASURE MENU
LIFE
DMX
VOLTAGE
TEMPERATURA
TWILIGHT
DELTA R
13
1)GLOBAL SETTING MENU
LANGUAGE
DEFAULT PAGE
SECURITY
DEFAULT SETTING
SET DATE
SET TIME
UPDATE
DOWNLOAD
ABOUT
A001
Up-Down
GLOBAL SETTING
Menu
Up-Down
Language
ENTER
LANGUAGE SELECTION
This menu allow to set the
Up-Down
Default Page
Security
Up-Down
Set Language
English
English = Default
Set Default Page
Four Digit = DMX address
visualisation
ENTER
Status = DMX / Color Mode / Boost
Power / Security
ENTER
ENTER
Up-Down
ENTER
DEFAULT PAGE SELECTION
This menu allow to set the
visualisation for the start up page
Up-Down
ENTER
Up-Down
Four Digit
Up-Down
A001
Status
ENTER
SECURITY PASSWORD
This menu allow to select a security
password to lock the user’s settings
Up-Down
Up-Down
Security
Unlocked
Enter Security Code
0 0 0 0
Default 0000 = no password
ENTER
Universal Unlock code = 2903
Confirm Security Code
0 0 0 0
Up-Down
Default Setting
ENTER
DEFAULT SETTINGS
This menu allow to set the unit to
the company settings
Up-Down
Set Date
DATE SETTING
This menu allow to set the day of
the week the month and the year
Up-Down
Up-Down
ENTER
Up-Down
Restore Main Settings
GAME,TIMER and WHITE SETTING
will not be changed
ENTER
ENTER to CONFIRM
& Reboot
ENTER
Date settings for Stand Alone mode
Set Date
Year
Month
Day of the month
Day of the week
2007
Jan
01
Mon
ENTER
14
Up-Down
Set Time
ENTER
Up-Down
TIME SETTING
This menu allow to set the unit’s on
board clock for STAND ALONE
MODE
Up-Down
Update
ENTER
Up-Down
DELTA R
Real time internal clock setting
Set Time
Hour
03
Minute
01
Select UPDATE Mode
Direct to PC
UPDATE MENU
This menu allow to upgrade the
uni’s software by computer or
remote control
ENTER
Update the unit’s software from PC by
cable
ENTER
Download the unit’s program to PC by
cable
ENTER
ENTER to CONFIRM
Up-Down
Download
ENTER
Up-Down
DOWNLOAD MENU
This menu allow to save unit’s
programs into computer
Select DOWNLOAD Mode
Direct to PC
ENTER to CONFIRM
Up-Down
ABOUT
ABOUT MENU
This menu show informations about
unit’s hardware and software
ENTER
Up-Down
About DELTA R
Master PCB
0514L019
Loader Version
1.02
HW Version
1.01
SW Version
1.61
Pan&Tilt PCB 0514S100
PAn&Tilt Version
2.05
Unit’s Hardware and software infos
ENTER
DELTA R
15
2)MODE SETTING MENU
MODE
MODE
MODE
MODE
MODE
MODE
MODE
DMX
RECORDER
MASTER
SLAVE
IR
MANUAL
TWILIGHT
A001
Up-Down
MODE SETTINGS
Menu
Up-Down
Mode DMX
ENTER
ENTER
Up-Down
DMX ADDRESS SELECTION
This menu allow to set the unit’s
DMX address.
Up-Down
Mode Recorder
Set Address DMX
Address range 001-489
ENTER
001
ENTER
Up-Down
RECORDER MODE SETTING
This menu let you create 2 different chases,CPR1
and CPR2 (16 steps each) that will then run in
Master Mode.
Two different recording mode are available:
1)Manual Recording Mode
2)DMX Recording Mode
1)Manual Recording Mode
2)DMX Recorder Mode
To program CPR1 and CPR2 by using a DMX controller,
3 more DMX channels are needed in addition to the 15
channels necessary to control the unit.
So that in RECORDER mode (via DMX) the unit will
need 18 channels to be correctly programmed.
The 3 new DMX channels are:
DMX channel 16 = STEPS channel
From 0 - 15 = VIEW DMX, the unit shows the values
received from the DMX controller in that moment.
From 16 – 255, the previously programmed steps (16
steps from 01 to 16) are displayed.
DMX channel 17 = VIEW / EDIT / SET LAST channel
If channel 16 (STEPS channel) is set to value 0 - 15,
the DMX channel 17 has no functions.
If channel 16 (STEPS channel) is set to value 16 - 255,
the DMX channel 17 has the following functions:
From 0 - 19 = VIEW MEM, the unit shows the
previously programmed steps.
From 20 - 234 = EDIT, the unit runs the configuration
given by the DMX controller in that moment.
RECORDER Mode
Input Mode
MANUAL
Select Chase
CPR1
RECORDER MANUAL
CPR1 STEP 01 EDIT
PAN
016
TILT 255
SHUTTER 009 DIMM 017
R 016
G 016
B 000
WHITE 012 CTC 000
MACRO 000
RECORDER Mode
Input Mode
DMX
Select Chase
CPR1
Warning 18 channels !
RECORDER DMX
CPR1 STEP 01 EDIT
PAN
016
TILT 255
SHUTTER 009 DIMM 017
R 016
G 016
B 000
WHITE 012 CTC 000
MACRO 000
In Manual Recording Mode,it is
possible to create and store the
steps of the chase by using the unit
display panel and buttons.
ENTER
Three different options are available:
1)EDIT = Let you modify and store
new values for all the channels on
the selected Step.
2)WIEV MEM = Let you see the
existing programmed steps of the
chase
3)SET LAST = Let you set the last
step to be ran on the chase.
In DMX Recording Mode,it is
possible to create and store the
steps of the chases by using an
external DMX controller.
WARNING !
To program CPR1 and CPR2 by using
a DMX controller, 3 more DMX
channels are needed in addition to
the 15 channels necessary to control
the unit.
With the STEPS channel it is possible to select the step to create, while with REC channel it is possible to store the configuration on the selected step.From 234 - 255 = SET LAST, the unit runs the configuration given by the DMX controller in that moment closing the Program as last step.
With the REC channel it is possible to record the selected step as last step to be ran on the Program.
DMX channel 18 = REC channel
REC channel saves the configuration given by the DMX controller in the selected step: you change the DMX value from 0 to 255 (the display shows
“WRITING” indicating that the step has been recorded). We suggest to keep the REC channel set to 0 and to run through the 255 only once you have
decided to save the new configuration. If CPR1 or CPR2 are not closed, by indicating the last step (Edit channel between 235-255), all 16 steps will be
played through in playback mode, even if not programmed.
ENTER
16
Up-Down
Mode Master
ENTER
Up-Down
MASTER MODE SETTING
This menu allow to set Delta R as
master unit (No DMX signal must
be present on unit’s DMX input
panel) .
The unit will ran in automatic mode
without needing of an external
controller.
Different chases are selectable by
user
Set MASTER MODE
Mode :
Actual :
MASTER
DMX
Up-Down
Master Mode
Set CHASE
Set TIME
Set WAIT
CPR1
Sec 0025
Sec 0015
CRNB
Rainbow colours effect.
Time and Pan&Tilt selectable by
user
SLAVE MODE SETTING
This menu allow to set the Delta R
as slave unit.
DMX signal must be present from
MASTER unit in order to ran in
SLAVE mode.
ENTER
By setting all the units connected to
the MASTER, to DMX address 1,
them will be sinchronized with the
Master unit following the chase
selected on it, including TIME, WAIT
and Pan&Tilt position of the MASTER
unit.
ENTER
By setting all the units connected to
the MASTER, as SLAVE unit (see
SLAVE mode), them will be
sinchronized with the Master unit
only for TIME and WAIT time, but
running their own chase CPR1/CPR2
with dedidicated Pan&Tilt position,
colors and effects.
CUE 1-9
Color Macros with fixed colors
Pan&Tilt selectable by user
Mode Slave
The Delta setted as MASTER, send
DMX signal to all the other units
connected to the same DMX line
ENTER to CONFIRM
CPR1/CPR2/CPR1&2
Chases with 16 steps previously
created in RECORDER mode.
Time and Wait time selectable by
user
Up-Down
DELTA R
ENTER
Up-Down
Set SLAVE MODE
Mode :
Actual :
SLAVE
DMX
ENTER to CONFIRM
The SLAVE unit receive DMX signal
from the MASTER unit
By setting all the units connected to
the MASTER, as SLAVE unit, them
will be sinchronized with the Master
unit only for TIME and WAIT time,
but running their own chase
CPR1/CPR2 with dedidicated
Pan&Tilt position, colors and effects.
ENTER
DELTA R
17
Up-Down
Mode IR
Set IR MODE
ENTER
Up-Down
Mode :
Actual :
IR MODE SETTING
By activating IR mode on Delta unit
it will be possible to navigate
trought the unit functions by using
the D.T.S. infrared remote control
(D.T.S. Code :0514L008).
IR
DMX
The unit is controlled by the infrared
remote control
ENTER
ENTER to CONFIRM
INFRARED REMOTE CONTROL
ON/OFF
Button
By activating IR mode on Delta unit it will be possible to navigate
trought the unit functions by using the D.T.S. infrared remote
control (D.T.S. Code :0514L008).
Infrared remote control functions:
ON/OFF and MUTE buttons
In Master/Slave mode let you stop the games running.
Master and slave units will go in Stand-by mode
1-9 buttons
Let you select the chase to run (CPR1/CPR2/CRNB/CUE 1-6)
1-/.. Button
Let you select the chase to run (CUE 7-9)
VOL +/No function
PROG +/Let you scroll between the selectable chases
RED/GREEN/YELLOW/BLUE buttons
Direct acces to cues for Red/Green/Blue/Yellow colour.
Red=CUE1 / Green=CUE3 / Yellow=CUE2 / Blue=CUE5
Navigation buttons
Same as UP/DOWN on unit display
OK button
Same as ENTER on unit display
MENU button
Same as MENU on unit display
Up-Down
Mode Manual
ENTER
Up-Down
MANUAL MODE SETTING
This menu let you control Delta unit in manual
mode by using the unit display.
In MANUAL mode, no external controller is
needed.
Set MANUAL MODE
Mode :
Actual :
MANUAL
DMX
ENTER to CONFIRM
MAN Mode Enter VALUES
Channel
PAN H
Value
128
1-9
Buttons
1-/..
Button
VOL +/Buttons
PROG +/Buttons
R-G-Y-B
Buttons
NAVIGATION
Buttons
OK
Button
In MANUAL mode it is possible to
adjust all the unit functions by using
UP/DOWN and ENTER buttons:
PAN H
PAN L
TILT H
TILT L
SPEED PAN&TILT
SHUTTER
DIMMER
RED
GREEN
BLUE
WHITE
CTC
MACRO
FUNCTION
RESET
MENU
Button
ENTER
DELTA R
18
Up-Down
TWILIGHT MODE
ENTER
Up-Down
TWILIGHT MODE MENU
This menu allow to set the unit in
Twilight mode.
Twilight mode let you turn ON and
OFF the unit at a specific clock time
(including day of the week) and/or
at a specific twilight level.
The Twilight mode make use of a
twilight sensor located on the front
panel near unit display.
To know the twilight ambient level
value measured from the sensor,
scroll the unit menu till MEASURE
Mode and select Twilight.
Set TWILIGHT MODE
Mode :
Actual :
TWILIGHT
DMX
ENTER to CONFIRM
TWILIGHT Mode
ACTION
CPR1
LEVEL ON 100 OFF 150:
TIME CONDIT INCLUSIVE
DAY Mon
START 22:00
TIME ON
10:00
The unit is switched on and off at
the desired twilight level or/and
at a specific clock time.
ACTION :
Let you select the desired
function in twilight mode.
You can choose between: DMX /
CPR1 / CPR2 / CPR1&2 / CRNB /
CUE 1-9 /
LEVEL ON and OFF :
Let you select the desired twilight
levels for:
Twilight mode ON and OFF.
TIME CONDITION:
Four different options are available:
1) INACTIVE
Clock time (START) and Time on period (TIME ON), are inactive.
In this condition the unit goes ON only if the twilight level is valid
2)COMBINED
Clock time (START), Time on period (TIME ON) and Twilight level are active.
In this condition, the unit goes ON only if all the parameters are valid.
3)INCLUSIVE
Clock time (START), Time on period (TIME ON) and Twilight level are active.
In this condition, the unit goes ON also if only one of the paramete is valid.
4)EXCLUSIVE
Clock time (START) and Time on period (TIME ON), are active, while Twilight level is inactive.
In this condition, the unit goes ON only if Clock time (START) is valid.
3)MOVING HEAD SETUP MENU
PAN MIN
PAN MAX
TILT MIN
TILT MAX
CALIBRATE PAN
CALIBRATE TILT
INVERT PAN
INVERT TILT
SWAP PAN & TILT
ENCODER
RESET PAN & TILT
SPEED PAN & TILT
A001
MOVING HEAD SETUP
Menu
Up-Down
ENTER
ENTER
DELTA R
19
A001
Up-Down
MOVING HEAD SETUP
Menu
Up-Down
Pan Min
ENTER
ENTER
Up-Down
PAN MINIMUM POSITION
This menu allow to set the Pan
minimum position (Default =000)
Up-Down
Pan Max
Tilt Min
ENTER
Up-Down
Tilt Max
ENTER
Up-Down
Calibrate Pan
ENTER
Up-Down
Calibrate Tilt
TILT CALIBRATION
This menu allow to calibrate Tilt
home position (Default = 128)
Setting Tilt Min
Setting Tilt Max
Tilt Max : 000
Calibrating Pan
ENTER
Up-Down
PAN CALIBRATION
This menu allow to calibrate Pan
home position (Default = 105)
Up-Down
Setting Pan Max
Range 255-000
Default = 255
ENTER
Range 000-255
Default = 000
ENTER
Range 255-000
Default = 255
ENTER
Tilt Min : 000
TILT MAXIMUM POSITION
This menu allow to set the Tilt
maximum position (Default = 255)
Up-Down
ENTER
Pan Man : 000
TILT MINIMUM POSITION
This menu allow to set the Tilt
minimum position in degrees
(Default =000)
Up-Down
Range 000-255
Default = 000
Pan Min : 000
PAN MAXIMUM POSITION
This menu allow to set Pan
maximum position (Default = 255)
Up-Down
Setting Pan Min
Pan :
ENTER
Up-Down
ENTER
Range 000-255
ENTER
105
Calibrating Tilt
Tilt :
Range 000-255
105
DELTA R
20
Up-Down
Invert Pan
ENTER
Up-Down
PAN INVERTION
This menu allow to set the Pan
movement.
Normal or Inverted
Up-Down
Invert Tilt
ENTER
Up-Down
TILT INVERTION
This menu allow to set the Tilt
movement.
Normal or Inverted
Up-Down
Swap Pan&Tilt
ENTER
Up-Down
PAN&TILT SWAP
This menu allow to invert the
control of Pan with the control of
Tilt.
Set PAN INVERTION
Pan :
Normal
Actual
Normal
Set TILT INVERTION
Tilt :
Normal
Actual
Normal
Set Pan/Tilt SWAPPING
Swap :
Normal
Actual
Normal
Pan movement Normal or Inverted
Default = Normal
ENTER
Tilt movement Normal or Inverted
Default = Normal
ENTER
Pan control inverted with Tilt control
and vice versa
Dfault = Normal
ENTER
IMPORTANT: (During PAN/TILT MIN,PAN/TILT MAX and PAN/TILT CALIBRATE setting,PAN/TILT INVERT and PAN/TILT SWAP are disabled
Up-Down
Encoder
ENTER
Up-Down
ENCODER SETTING
This menu allow to enable/disable
the auto-repositioning function for
Pan and Tilt
Up-Down
Reset Pan & Tilt
Encoder : Active
Actual
Speed Pan & Tilt
PAN & TILT MAXIMUM SPEED
This menu allow to set the
maximum speed for Pan & Tilt
movement.
Pan/Tilt auto-repositioning system
enabled or disabled
Default = Active
ENTER
Active
Resetting Pan & Tilt
ENTER
PAN&TILT RESET
This menu allow to reset Pan and
Tilt Motors
Up-Down
Set Encoder Status
Pan &Tilt motors reset
ENTER
PRESS ENTER
To RESET Pan & Tilt
ENTER
Up-Down
Set SPEED MAX P&T
Speed MAX % 100
Pan&Tilt maximum motor speed
Selectable between 25-100%
ENTER
DELTA R
21
4)LED SETUP MENU
COLOUR MODE
WHITE BALANCE
BOOST DRIVING
MIN RGB
MAX RGB
SMOOT FILTER
PWM FREQUENCY
A001
Up-Down
LED SETUP
Menu
Up-Down
Colour Mode
ENTER
ENTER
Up-Down
COLOUR MODE
This menu allow to select the LED’S
colour mode control system
between RGB, CMYK or HSV
Set Colour Mode
RGB
CMYK
HSV
Actual
RGB
RGB Mode (Default)
Ch7 = Dimmer / Ch8 = Red Ch9= Green
/ Ch10= BLue
ENTER
CMYK Mode
Ch7 = Black / Ch8 = Cyan
Ch9= Magenta / Ch10= Yellow
HSV Mode
Ch7 = Nu / Ch8 = Hue
Ch9= Saturation / Ch10= Value
Up-Down
White balance
ENTER
Up-Down
ENTER
Up-Down
WHITE BALANCE
This menu allow to select the levels
for Red,Green and blue obtaining a
custom White
Up-Down
Boost Driving
BOOST DRIVING
This menu allow to increase the
LED’s current from 350mA to 500
mA
Setting WHITE
RED
255
GREEN
255
255
BLUE
The Custom White can be
Recall by setting DMX channel 11
(WHITE) in the range 172-213
Setting LED BOOST
BOOST Status
Whit BOOST active,the LED’s current is
setted to 500mA (30%more gain).
Default = Disable
NTC thermal protection active.
Active
ENTER
ENTER
Warning TEMPERATURE
PROTECTION ACTIVATED
Up-Down
Min RGB
Setting RGB Min
ENTER
Up-Down
RGB MINIMUM VALUES
This menu allow to select the
minimum levels for Red,Green and
blue
Up-Down
Max RGB
RGB MAXIMUM VALUES
This menu allow to select the
maximum levels for Red,Green and
blue
These settings have priority on Master
Dimmer (DMX channel 7)
ENTER
These settings have priority on Master
Dimmer (DMX channel 7)
ENTER
Min RED
: 000
Min GREEN : 000
Min BLUE : 000
Setting RGB Max
ENTER
Up-Down
Max RED : 000
Max GREEN: 000
Max BLUE : 000
DELTA R
22
Up-Down
Set Smooth Filter
Smooth Filter
ENTER
Up-Down
SMOOTH FILTER VALUE
This menu allow to select the value
of the delay( in millisecons) for RGB
channels reaction to DMX or
Program variation.
001=2.5 ms delay (Fast response)
100=250 ms delay (Slow response)
Up-Down
PWM frequency
Filter Value:
010
ENTER to CONFIRM
Set PWM Frequency
ENTER
Up-Down
PWM FREQUENCY VALUE
This menu allow to adjust the PWM
frequency value (Hz) in order to
reduce flickering in the process of
your camera recordings
427 Hz
1000 Hz
2000 Hz
4000 Hz
6000 Hz
Actual
Range = 001 / 100
Default = 10
001 = 2.5mS (Istant response to DMX
variation)
100 = 250mS (Smooth response to
DMX variation)
5 different PWM frequencies available.
Default = 427 Hz
ENTER
ENTER
427 Hz
5)DIPLAY SETUP MENU
CONTRAST
FLIP DISPLAY
SCREEN SAVER
A001
Up-Down
DISPLAY SETUP MENU
Menu
Up-Down
Contrast
ENTER
Range = 0-9
ENTER
Up-Down
Contrast 7
ENTER
DISPLAY CONTRAST
This menu allow to select display’s
contrast level.
0 1 2 3 4 5 6 7 8 9
Up-Down
Flip Display
ENTER
DISPLAY FLIP
This menu allow to reverse display's
reading depending on the
mounting position
(On the ground or suspended).
Up-Down
Screen saver
SCREEN SAVER
This menu allow to activate the
screen saver.
Default = On the ground
Up-Down
ENTER
Flip Select
A
ENTER
Up-Down
SCREEN SAVER SETTING
Screen Type
None
Screen Time (sec):005
Screen saver selectable between None
(default) and Blank.
Screen saver activating time selectable
between 005 / 180 seconds
ENTER
DELTA R
23
6)MEASURE MENU
LIFE
DMX
VOLTAGE
TEMPERATURE
TWILIGHT
A001
Up-Down
Life
MEASURE MENU
Menu
Up-Down
ENTER
LIFE TIME
This menu show the total UNIT LIFE TIME
(reset not possible) and the RGB life
TIME (reset possible)
ENTER
Up-Down
Measure Life
Total Unit Life Time
Reset not possible
ENTER
Delta R Total LIFE
Days Hours Min Sec
1 19
47
55
UP/DW Change Measure
Measure Life
Delta R RED LIFE
To resed Red life time,keep pushed
Enter button for more than 5
seconds
ENTER
Days Hours Min Sec
0
5
22
30
UP/DW Change Measure
Measure Life
Delta R GREEN LIFE
To resed Green life time,keep
pushed Enter button for more than
5 seconds
ENTER
Days Hours Min Sec
0
4
37
15
UP/DW Change Measure
Measure Life
Delta R BLUE LIFE
Days Hours Min Sec
0
4
06
53
UP/DW Change Measure
To resed Blue life time,keep
pushed Enter button for more than
5 seconds
ENTER
24
Up-Down
Dmx
ENTER
Up-Down
DMX
This menu show the DMX channel levels
Up-Down
Voltage
Measure VOLTAGE
ENTER
Temperature
V
V
V
V
Motor
Power
Internal
Oled
TWILIGHT
This menu show the twilight level.
ENTER
ENTER
36,9
160,5
17,6
13,2
Up-Down
ENTER
Measure TEMPERATURE
Celsius
Twilight
All the values are espressed in Volt
LED’s temperature monitor
ENTER
TEMPERATURE
This menu show the NTC sensor
temperature.
Up-Down
DMX channel levels as received from
DMX line
Up-Down
VOLTAGE
This menu show the different Voltage
levels for every electronic circuit inside
the unit
Up-Down
Measure DMX
Start Channels Values
001 000 000 000 000
005 000 000 000 000
009 000 000 000 000
013 000 000 000 000
DELTA R
ENTER
Up-Down
20,5
Measure TWILIGHT
Value :
0314
Light sensor Twilight level
(Located on the front panel of the
unit)
ENTER
25
DELTA R
9- OPENING UP THE PROJECTOR HOUSING:
It is possible to inspect the inside of the projector by removing the covers as shown below.
Attention: REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR'S INTERNAL
COMPONENTS.
Proceed as per the pictures below
9.1- Arms
Remove these two screws on both arm sides
9.2- Base
Remove the 12 screws located on the base
DELTA R
26
10- CHANGHING THE LENSES
Delta R Full Color
Optical Lenses set can be interchanged by users.
Three different models are available: (spot / medium /wide)
Lenses set spot (cod. 03.LK.008)
Lenses set medium (cod. 03.LK.001)
Lenses set wide (cod. 03.LK.002)
To change the lenses set, proceed as per the pictures below
Remove these 12 screws on both
sides of the rear head assembly
Remove the top head cover
Remove these 8 screws and change
the panel
ATTENTION:
Never touch LEDs and Lensens
with hands
DELTA R
27
10- CHANGHING THE LENSES
Delta R Triled
Optical Lenses set can be interchanged by users.
Three different models are available: (spot / medium /wide)
Lenses set spot (cod. 03.LK.008)
Lenses set medium (cod. 03.LK.001)
Lenses set wide (cod. 03.LK.002)
To change the lenses set, proceed as per the pictures below
Remove these 12 screws on both
sides of the rear head assembly
Remove the top head cover
Remove these 6 screws and change
the panel
ATTENTION:
Never touch LEDs and Lensens
with hands
28
DELTA R
11- PERIODIC CLEANING:
Front lenses Glass
The dust can reduce the luminous output substantially. Regularly clean the front lenses glass using
a soft cotton cloth, dampened with a specialist glasses cleaning solution.
12- PERIODIC CONTROLS:
Mechanical parts:
Periodically check all mechanical parts and the gaskets, replacing them if necessary.
Electrical components:
Check all electrical components for correct earthing and proper attachment of all connectors,
refastening if necessary.
Fuse replacement:
Locate the fuse, which protect the electronics, in the base of the DELTA R.
Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if
necessary.
Attention: Disconnect mains power prior to removing the projector housing.
DELTA R
29
13- DMX PROTOCOL
15 CHANNELS MODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PAN msb 320°
PAN lsb
TILT msb 180°
TILT lsb
SPEED MOVEMENT
SHUTTER
DIMMER
RED
GREEN
BLUE
WHITE (Preprogrammed white at different color temperature)
CTC
COLOURS MACRO
FUNCTIONS
RESET
DMX CHANNEL
1
Parameter: PAN msb
DMX CHANNEL
2
Parameter: PAN lsb
DMX CHANNEL
3
Parameter: TILT msb
DMX CHANNEL
4
Parameter: TILT lsb
DMX CHANNEL
5
Parameter: MOVEMENT SPEED
DMX range
Value
Mid point
DMX value
0-10
11-255
5
DMX CHANNEL
6
Mode
Option
Function
Standard
Vector mode from fast to slow
Parameter: SHUTTER
DMX range
Value
Mid point
DMX value
0-9
10-19
20-29
30-119
120-149
150-179
180-204
205-229
230-244
245-255
5
14
24
192
218
238
250
Move
range
(degrees)
Move
range
(degrees)
Mode
Option
Function
Black-out
Open
Black-out
Strobe at variable speed(from slow to fast)
Pulse open at variable speed(from slow to fast)
Pulse close at variable speed(from slow to fast)
Random Strobe (Master and RGB active)
Random Strobe (Full)
PAn&Tilt movement in Black-out
Open
DELTA R
30
DMX CHANNEL
7
DMX range
Value
Mid point
DMX value
Parameter: DIMMER
Move
range
(degrees)
NOTE: IN CMYK MODE Ch7 = BLACK
Mode
Option
0-255
DMX CHANNEL
DMX range
Value
Proportional dimmer
8
Parameter: RED
Mid point
DMX value
NOTE: IN CMYK MODE Ch8 = CYAN
IN HSV MODE Ch8 = HUE
Move
range
(degrees)
Mode
Option
0-255
DMX CHANNEL
DMX range
Value
DMX range
Value
9
Parameter: GREEN
Mid point
DMX value
Move
range
(degrees)
NOTE: IN CMYK MODE Ch9 = MAGENTA
IN HSV MODE Ch9 = SATURATION
Mode
Option
Function
Proportional colour
10
Parameter: BLUE
Mid point
DMX value
Move
range
(degrees)
NOTE: IN CMYK MODE Ch10 = YELLOW
IN HSV MODE Ch10 = VALUE
Mode
Option
0-255
DMX CHANNEL
Function
Proportional colour
0-255
DMX CHANNEL
Function
Function
Proportional colour
11
Parameter: WHITE (Pre-programmed White at diff. color temperature)
DMX range
Value
Mid point
DMX value
0-43
44-85
86-127
21
66
105
Move
range
(degrees)
Mode
Option
Function
No Function
Full (Red-Green-Blue at Full)
White DTS
IF CHANNEL 14 (FUNCTIONS) = CUSTOM WHITE RECALL (Dmx range value 0 - 79)
128-171
150
Custom White Recall
White
Balance(White
Balance
programmed
on Unit’s Menu)
172-213
192
White CTC (Channel 12 CTC enabled
234
214-255
Linear color temp. Correction: 3000K-7000K)
IF CHANNEL 14 (FUNCTIONS) = CUSTOM WHITE CREATE (Dmx range value 80 - 160)
128-171
150
Custom White Create (RGB levels selectable by DMX)
White Balance(White Balance programmed on Unit’s Menu)
172-213
192
White CTC (Channel 12 CTC enabled
234
214-255
Linear color temp. Correction: 3000K-7000K)
DELTA R
31
DMX CHANNEL
DMX range
Value
12
Parameter: CTC (Color temperature correction)
Mid point
DMX value
Move
range
(degrees)
Mode
Option
Function
IF CHANNEL 11 (White) = WHITE CTC (Dmx range value 214 - 255)
Linear color temp. Correction: 0 = 3000K / 128 = 5500K / 255 = 7000K
0-255
IF CHANNEL 11 (White) = NO FUNCTION (Dmx range value 0 - 43)
Smooth RGB linear Hue correction
0-255
DMX CHANNEL
DMX range
Value
13
Parameter: COLOUR MACROS
Mid point
DMX value
Move
range
(degrees)
Mode
Option
No Function
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12
Macro 13
Macro 14
Macro 15
Macro 16
0-14
15-29
30-44
45-59
60-74
75-89
90-104
105-119
120-134
135-149
150-164
165-179
180-194
195-209
210-225
226-239
240-255
DMX CHANNEL
14
DMX range
Value
Mid point
DMX value
Parameter: FUNCTIONS (Recall,Create and Store the Custom white)
0-79
80-160
161-255
DMX CHANNEL
DMX range
Value
0-15
16-255
Function
15
Parameter: RESET (Pan&Tilt Reset)
Mid point
DMX value
8
120
Move
Mode
Option
Function
range
(degrees)
Custom White Recall (Enable CH 11 for Custom white Recall)
Custom White Create (Enable CH 11 for Custom white Creation)
Custom White Store (Store the Custom White created )
Move
range
(degrees)
Mode
Option
Function
No Functions
Pan&Tilt Reset
The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this document
cannot be copied, photocopied or reproduced, in part or completely, without prior written consent
from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its
products without prior notice. D.T.S. assumes no responsibility for the use or application of the
products or circuits described herein.
MADE IN ITALY
*0517I069*
*0517I069*
D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy
Tel. +39 0541 611131 Fax +39 0541 611111
info@dts-lighting.it www.dts-lighting.it