ProForm 780 Crosswalk Treadmill User`s manual

www.proform.com
Model No. PFTL79008.0
Serial No.
Write the serial number in the space
above for reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts
are missing, DO NOT CONTACT
THE STORE; please contact
Customer Care.
IMPORTANT: You must note the
product model number and
serial number (see the drawing
above) before contacting us:
1-888-533-1333
CALL TOLL-FREE:
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.proformservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
USERʼS MANUAL
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
HOW TO USE THE CHEST PULSE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the locations of the
warning decals. If a decal is missing or illegible, call the telephone number on the
front cover of this manual and request a
free replacement decal. Apply the decal
in the location shown. Note: The decals
may not be shown at actual size.
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or persons with
pre-existing health problems.
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 15. To purchase a surge suppressor, see
your local PROFORM dealer or call the telephone number on the front cover of this manual and order part number 146148, or see your
local electronics store.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
13. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Keep the power cord and the surge suppressor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 22 if the treadmill is
not working properly.)
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 17).
8. The treadmill should be used only by persons
weighing 350 lbs. (159 kg) or less.
9. Never allow more than one person on the
treadmill at a time.
17. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails or crosswalk arms while using the
treadmill.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear athletic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensors are not medical devices.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as exercise aids in determining heart
rate trends in general.
11. When connecting the power cord (see page
15), plug the power cord into a surge suppressor (not included) and plug the surge
suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
3
24. Inspect and properly tighten all parts of the
treadmill regularly.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off circuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
25.
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 21.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
DANGER:
Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the maintenance and adjustment procedures described in
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
22. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
23. Never insert any object into any opening on
the treadmill.
SAVE THESE INSTRUCTIONS
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
780 CROSSWALK treadmill. The 780 CROSSWALK
treadmill offers an impressive selection of features designed to make your workouts at home more enjoyable
and effective. And when youʼre not exercising, the
unique treadmill can be folded up, requiring less than
half the floor space of other treadmills.
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.proformservice.com/registration.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after reading this manual, please see the front cover of this man-
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Accessory Tray
Console
Pulse Sensor
Handrail
Key/Clip
Crosswalk Arm
Upright
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Platform Cushion
Idler Roller
Adjustment Bolts
5
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex key and your own Phillips screwdriver
,
adjustable wrench
, needlenose pliers
, scissors
, and rubber mallet
.
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached
to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly. Extra hardware may be included.
#10 Star
Washer (12)–4
#8 x 1/2"
Screw (2)–2
3/8" Star
Washer (11)–4
#8 x 3/4"
Screw (1)–6
5/16" x 1 3/4" Bolt (5)–4
3/8" Nut (10)–3
Base Foot
Spacer (98)–2
#8 x 3/4"
Tek Screw (13)–2
3/8" x 1 3/4" Bolt (7)–1
3/8" x 4" Bolt (8)–4
6
#8 x 1 1/2" Screw (3)–4
#8 x 1"
Tek Screw (6)–4
#10 x 3/4"
Screw (4)–4
3/8" x 2" Bolt (9)–3
1. Make sure that the power cord is unplugged.
1
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (48) so that the treadmill is more stable;
do not fully fold the Frame yet.
Hole
91
97
96
Cut the shipping tie securing the Wire Harness
(91) to the Base (96). Locate the plastic tie in
the indicated hole in the Base, and use the tie to
pull the Wire Harness out of the hole.
98
48
Attach two Base Feet (97) to the Base (96) in the
locations shown with two #8 x 1" Tek Screws (6)
and two Base Foot Spacers (98).
6
97 6
97
Then, attach the other two Base Feet (97) with
two #8 x 1" Tek Screws (6).
6
97
6
98
2. See the inset drawing. Cut the plastic tie near
the Wire Harness (91).
2
Attach a Wheel (99) to the Base (96) with a 3/8"
x 2" Bolt (9) and a 3/8" Nut (10). Do not overtighten the Nut; the Wheel must turn freely.
Plastic Tie
9
10
3. Identify the Right Upright (92) and the Right
Upright Spacer (100), which are marked with
stickers. Insert the Wire Harness (91) through
the Right Upright Spacer as shown. Then, set
the Right Upright Spacer on the Base (96).
99
96
Cut
91
3
91
Have a second person hold the Right Upright
(92) near the Base (96). See the inset drawing.
Tie the wire tie in the Right Upright securely
around the end of the Wire Harness (91). Then,
pull the other end of the wire tie until the Wire
Harness is routed completely through the Right
Upright.
7
91
92
Wire Tie
92
Wire
Tie
100
91
96
4. Hold a Bolt Spacer (95) inside the lower end of
the Right Upright (92). Insert a 3/8" x 4" Bolt (8)
with a 3/8" Star Washer (11) into the Right
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (95), 3/8" x 4" Bolt
(8), and 3/8" Star Washer (11).
4
8
92
11
91
Hold the Right Upright (92) against the Right
Upright Spacer (100). Be careful not to pinch
the Wire Harness (91). Tighten the 3/8" x 4"
Bolts (8) until the heads of the Bolts touch the
Right Upright; do not fully tighten the Bolts
yet.
95
95
100
93
96
Press a Base Cap (93) into the Base (96).
5. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (48) so the treadmill is more stable; do
not fully fold the Frame yet.
5
Attach a Wheel (99) to the Base (96) with a 3/8"
x 2" Bolt (9) and a 3/8" Nut (10). Do not overtighten the Nut; the Wheel must turn freely.
9
96
8
99
10
48
6. Hold a Bolt Spacer (95) inside the lower end of
the Left Upright (77). Insert a 3/8" x 4" Bolt (8)
with a 3/8" Star Washer (11) into the Left
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (95), 3/8" x 4" Bolt
(8), and 3/8" Star Washer (11).
6
8
77
11
Hold the Left Upright Spacer (94) and the Left
Upright (77) against the Base (96). Tighten the
3/8" x 4" Bolts (8) until the heads of the Bolts
touch the Left Upright; do not fully tighten the
Bolts yet.
94
95
93
Press a Base Cap (93) into the Base (96).
95
96
With the help of a second person, tip the treadmill so that the Base (96) is flat on the floor.
7. Attach two Top Handrail Spacers (64) to the
Uprights (77, 92) with two #8 x 3/4" Tek Screws
(13).
7
13
64
77
13
64
8. Hold a Bottom Handrail Spacer (68) against the
Right Upright (92). Align the holes in the Bottom
Handrail Spacer with the holes in the Top
Handrail Spacer (64). Then, slide a Handrail
(80) onto the Handrail Spacers. Attach the
Handrail and Bottom Handrail Spacer to the
Right Upright with two 5/16" x 1 3/4" Bolts (5);
do not fully tighten the Bolts yet.
92
8
5
Repeat this step with the other Handrail (80)
and Bottom Handrail Spacer (68).
80
64
68
77
80
9
5
64
68
92
9. Set the console assembly face down on a soft
surface to avoid scratching the console assembly. Remove the two #8 x 3/4" Screws (1). Lift
off the Pulse Bar (110). Save the Pulse Bar
and the two Screws for assembly steps 10
and 12.
9
1
110
Console
Assembly
10. Set the Pulse Bar (110) on the Left and Right
Uprights (77, 92). Attach the Pulse Bar with four
#10 x 3/4" Screws (4) and four #10 Star
Washers (12). Start all four Screws before
firmly tightening any of them. Be careful not
to pinch the Wire Harness (91).
10
4
12
110
5
Firmly tighten the four 5/16" x 1 3/4" Bolts
(5).
4
5
77
12
91
92
11. While a second person holds the console assembly near the Pulse Bar (110), connect the
Console Ground Wire (109) on the Pulse Bar to
the ground wire from the console assembly.
11
Connect the console wire to the Wire Harness
(91). See the inset drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and
then try again. IF THE CONNECTORS ARE
NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE
POWER IS TURNED ON. Lay the wires inside
the bottom of the Pulse Bar (110).
Console
Assembly
Console
Wire
Ground
Wire
91
109
110
10
Console Wire
91
12. Set the console assembly on the Left and Right
Uprights (77, 92). Be careful not to pinch any
wires.
12
Console Assembly
Attach the console assembly to the Pulse Bar
(110) with six #8 x 3/4" Screws (1). Start all six
Screws before firmly tightening any of them.
Note: Use the two Screws you removed in step 9.
92
13. Identify the Right Handrail Cover (55), which is
marked with a sticker. Slide the Right Handrail
Cover onto the right Handrail (80).
13
Remove the paper backing from the tape in the
indicated location and press the Right Handrail
Cover (55) against the console assembly.
Tighten a #8 x 1/2" Screw (2) into the Right
Handrail Cover and the Right Upright (92); be
careful not to overtighten the Screw.
Start the two indicated #8 x 1 1/2" Screws (3)
into the Left and Right Uprights (77, 92) and the
console assembly. If necessary, pull back on the
console assembly slightly to align the holes in
the Uprights with those on the console assembly. Start the other two #8 x 1 1/2" Screws (3)
and then tighten all four Screws; do not
overtighten the Screws. Then, raise the
Uprights (77, 92).
1
1
1
77
Console
Assembly
Tape
80
Attach the Left Handrail Cover (78) in the
same way.
14. Carefully lower the Uprights (77, 92) as shown.
110
78
2
Tape
80
14
Start
First
See steps 4 and 6. Firmly tighten the four 3/8" x
4" Bolts (8).
Console Assembly
3
92
11
55
2
92
Start First
3
77
15. Remove the Resistance Knob (88) from a resistance assembly. Make sure that the 3/8" x 4
3/4" Bolt (90) stays inside the resistance assembly and that the resistance assembly
does not come apart. Note: See the lower
drawing to reassemble the resistance assembly,
if necessary.
15
77
Large
84 Holes
88
Apply a small amount of the included grease
around the Resistance Cone (85). Insert the
Resistance Cone into the Upright Insert (84) in
the Left Upright (77), with the two large holes on
top as shown. Then, tighten the Resistance
Knob (88) onto the 3/8" x 4 3/4" Bolt (90).
85
Grease
Attach the other resistance assembly to the
Right Upright (92) in the same way.
88
16. Insert the end of a Crosswalk Arm (82) into the
hole in the top of a resistance assembly. Make
sure that the bend in the Crosswalk Arm is
positioned as shown.
84
90
Large
Holes
85
90
16
Tighten a #8 x 3/4" Screw (1) into the resistance
assembly and Crosswalk Arm (82) from the direction shown. Press a Small Cap (89) into the
hole for the Screw.
Bend
Attach the other Crosswalk Arm (82) in the
same way.
82
Hole
Resistance
Assembly
1
Bend
89
82
89
12
92
Resistance
Assembly
1
17. Raise the Frame (48) to the position shown.
Have a second person hold the Frame until
this step is completed.
17
48
10
Orient the Storage Latch (45) so that the large
barrel and the Latch Knob (46) are in the positions shown.
Attach the upper end of the Storage Latch (45)
to the bracket on the Frame (48) with a 3/8" x 2"
Bolt (9) and a 3/8" Nut (10).
9
45
46
Attach the lower end of the Storage Latch (45) to
the Base (96) with a 3/8" x 1 3/4" Bolt (7). Note:
It may be necessary to move the Frame (48)
back and forth to align the Storage Latch with
the Base.
Large
Barrel
Lower the Frame (48) (see HOW TO LOWER
THE TREADMILL FOR USE on page 21).
96
7
18. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used
to adjust the walking belt (see pages 23 and 24).
13
HOW TO USE THE CHEST PULSE SENSOR
HOW TO PUT ON THE CHEST PULSE SENSOR
The chest pulse sensor consists of two components—
the chest strap and the sensor unit.
Tabs
Sensor Unit
Chest Strap
Tab
Sensor
Unit
Buckle
Insert the tab on one end of the chest strap into the
hole in one end of the sensor unit, as shown in the inset
drawing above. The tab should be flush with the front of
the sensor unit.
Next, wrap the chest
pulse sensor around
your chest and attach
the other end of the
chest strap to the
sensor unit. Adjust
the length of the
chest strap, if necessary. The chest pulse
sensor should be under your clothes, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
Pull the sensor unit away from your body a few inches
and locate the two electrode areas on the inner side
(the electrode areas are covered by shallow ridges).
Using saline solution such as saliva or contact lens solution, wet both electrode areas. Return the sensor unit
to a position against your chest.
CHEST PULSE SENSOR CARE AND MAINTENANCE
• Thoroughly dry the chest pulse sensor after each
use. The chest pulse sensor is activated when the
electrode areas are wetted and the chest pulse sensor is put on; the chest pulse sensor shuts off when
it is removed and the electrode areas are dried. If
the chest pulse sensor is not dried after
each use, it may remain activated longer than necessary, draining the battery prematurely.
• Store the chest pulse sensor in a warm, dry place.
Do not store the chest pulse sensor in a plastic bag
or other container that may trap moisture.
• Do not expose the chest pulse sensor to direct
sunlight for extended periods of time; do not expose
it to temperatures above 122° F (50° C) or below 14°
F (-10° C).
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse sensor.
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
CHEST PULSE SENSOR TROUBLESHOOTING
The instructions on the following pages explain
how the chest pulse sensor is used with the console. If the chest pulse sensor does not function
properly, try the steps below.
• Make sure that you are wearing the chest pulse sensor as described at the left. Note: If the chest pulse
sensor does not function when positioned as described, move it slightly lower or higher on your chest.
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the
sensor unit. If heart rate readings do not appear until
you begin perspiring, rewet the electrode areas.
• As you walk or run on the treadmill, position yourself near the center of the walking belt. For the
console to display heart rate readings, the user
must be within armʼs length of the console.
• The chest pulse sensor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contractions (pvcs), tachycardia bursts, and arrhythmia.
• The operation of the chest pulse sensor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
14
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
1
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeʼs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call the telephone
number on the front cover of this manual and order
part number 146148, or see your local electronics
store.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may slow, accelerate, or stop unexpectedly, which
may result in a fall and serious injury.
Grounded Outlet Box
Grounding Pin
2
Grounded Outlet
Grounding Plug
Grounded Outlet Box
Adapter
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
15
CONSOLE DIAGRAM
Key
Clip
FEATURES OF THE CONSOLE
To turn on the power, see page 17. To use the manual mode, see page 17. To use a preset workout,
see page 19. To use the information mode, see
page 20.
The treadmill console offers a selection of features designed to make your workouts more effective. When
you use the manual mode, you can change the speed
and incline of the treadmill with the touch of a button.
As you exercise, the console will display instant exercise feedback. You can even measure your heart rate
using the handgrip pulse sensor or the chest pulse
sensor. See page 14 for information on the chest pulse
sensor.
IMPORTANT: If there is a sheet of clear plastic on
the console, remove the plastic. To prevent damage to the walking platform, wear clean athletic
shoes while using the treadmill. The first time you
use the treadmill, observe the alignment of the
walking belt, and center the walking belt if necessary (see page 24).
In addition, the console offers fifteen preset workouts;
three of these use the crosswalk arms. Each workout
automatically controls the speed and incline of the
treadmill as it guides you through an effective exercise
session.
Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of measurement, see THE INFORMATION MODE on page
20. Note: For simplicity, all instructions in this section
refer to miles.
16
HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room temperature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
Plug in the power cord (see
page 15). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
power cord. Switch the circuit breaker to the reset position.
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
When you insert the key,
the manual
mode will be
selected. If
you have selected a workout, reselect
the manual mode by pressing any of the Trainer
Workouts buttons repeatedly until a track appears
in the upper half of the display.
Reset
Position
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is displayed in a store. If the displays light as soon as
you plug in the power cord and switch the reset/off
circuit breaker to the reset position, the demo
mode is turned on. To turn off the demo mode,
hold down the Stop button for a few seconds. If the
displays remain lit, see THE INFORMATION MODE
on page 20 to turn off the demo mode.
3. Start the walking belt.
To start the walking belt, press the Start button, the
Speed increase button, or one of the Quick Speed
buttons numbered 1 to 10.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 16)
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the displays will light. IMPORTANT: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the position of the clip.
If you press the Start button or the Speed increase
button, the walking belt will begin to move at 1 mph.
As you exercise, change the speed of the walking
belt as desired by pressing the Speed increase and
decrease buttons. Each time you press a button,
the speed setting will change by 0.1 mph; if you
hold down a button, the speed setting will change
in increments of 0.5 mph. Note: After you press the
buttons, it may take a moment for the walking belt to
reach the selected speed setting.
If you press one of the numbered Quick Speed buttons, the walking belt will gradually change speed
until it reaches the selected speed setting.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To restart
the walking belt, press the Start button, the Speed
increase button, or one of the numbered Quick
Speed buttons.
4. Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Incline increase and decrease buttons. Each time
you press a button, the incline will change by 0.5%.
Note: After you press the buttons, it may take a
moment for the treadmill to reach the selected incline setting.
17
5. Follow your progress with the displays.
When the
manual mode
is selected,
the upper half
Track
of the display
can show a
track that represents 1/4 mile (400 meters). As you
walk or run, indicators will appear in succession
around the track until the entire track appears. The
track will then disappear and the indicators will
again begin to appear in succession.
6. Measure your heart rate if desired.
Note: If you use the handgrip pulse sensor and
the chest pulse sensor at the same time, the
console will not display your heart rate accurately. See page 14 for information about the chest
pulse sensor.
Before using the
handgrip pulse
sensor, remove
the sheets of
clear plastic from
the metal contacts. In addition,
make sure that
your hands are
clean.
The lower left corner of
the display can show
the distance that you
have walked or run, the
elapsed time, the incline
level of the treadmill,
and the approximate number of grams of carbs you
have burned. Note: When a workout is selected,
the display will show the time remaining in the
workout instead of the elapsed time.
The lower right corner of
the display can show
the approximate number
of calories you have
burned while walking or
running, the speed of
the walking belt, and your pace in minutes per mile.
The lower right corner of the display will also show
your heart rate when you use the handgrip pulse
sensor or the chest pulse sensor. See page 14 for
information about the chest pulse sensor.
The upper half of the display can show the elapsed
time, the distance that you have walked or run, the
speed of the walking belt, the approximate number
of calories you have burned, your pace, the incline
level, or a track. Press the Display button repeatedly until the upper half of the display shows the information that you are interested in viewing. Note:
While information is shown in the upper half of the
display, the same information will not be shown in
the lower left or lower right corner of the display.
Contacts
To measure your heart rate, stand on the foot
rails and hold the metal contacts. Avoid moving
your hands. When your pulse is detected, a heart
symbol will flash in the lower right display each
time your heart beats, one or two dashes will appear, and then your heart rate will be shown. For
the most accurate heart rate reading, continue
to hold the contacts for about 15 seconds.
7. Turn on the fan if desired.
The fan features low and high speed settings.
Press the Fan button repeatedly to select a fan
speed or to turn off the fan. Note: If the fan is on
when the walking belt is stopped, the fan will turn
off automatically after a few minutes.
8. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
or you may damage the treadmill when you fold
it to the storage position. Next, remove the key
from the console and put it in a secure place.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmillʼs electrical components may wear prematurely.
To reset the display, press the Stop button, remove
the key, and then reinsert the key.
18
HOW TO USE A PRESET WORKOUT
If you have selected workout 13, 14, or 15, you will
be prompted to use the crosswalk arms. When the
words START CROSSWALK flash in the display,
move the crosswalk arms forward and backward as
you walk on the treadmill. This action exercises
your arms, shoulders, and back for a total body
workout. When the words STOP CROSSWALK
flash in the display, stop moving the crosswalk
arms and hold the handrails.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 17.
2. Select a preset workout.
To select a preset workout, press the Weight Loss,
Aerobic, Endurance, Performance, or Cross Walk
button repeatedly until the number of the desired
workout appears in the upper half of the display.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the speed or incline
buttons; however, when the next segment of the
workout begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
When you
select a preset workout,
the incline
level, duration, and the
speed setting
will appear in the display. A profile of the speed settings of the workout will scroll across the upper half
of the display.
To change the intensity level of the entire program,
press the Intensity increase or decrease button.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start button
or the Speed increase button. The walking belt will
begin to move at 1 mph. When the next segment of
the workout begins, the treadmill will automatically
adjust to the speed and incline settings for the next
segment.
3. Start the walking belt.
Press the Start button or the Speed increase button
to start the workout. A moment after you press the
button, the treadmill will automatically adjust to the
first speed and incline settings of the workout. Hold
the handrails and begin walking.
Each workout is divided into several one-minute
segments. One speed setting and one incline setting are programmed for each segment. Note: The
same speed setting and/or incline setting may be
programmed for consecutive segments.
During the
workout, the
profile will
show your
progress. The
Current Segment
flashing segment of the
profile represents the current segment of the workout. The height of the flashing segment indicates
the speed setting for the current segment. At the
end of each segment, a series of tones will sound
and the next segment of the profile will begin to
flash. The new speed and incline settings will appear in the display and the treadmill will automatically adjust to the new speed and incline settings.
The workout will continue in this way until the last
segment of the workout ends. The walking belt will
then slow to a stop.
4. Follow your progress with the displays.
See step 5 on page 18.
5. Measure your heart rate if desired.
See step 6 on page 18.
6. Turn on the fan if desired.
See step 7 on page 18.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 18.
19
THE INFORMATION MODE
HOW TO USE THE CROSSWALK ARMS
The console features an information mode that keeps
track of treadmill usage information. The information
mode also allows you to select miles or kilometers as
the unit of measurement and to turn on and turn off the
display demo mode.
As you walk on the treadmill, you can hold the
handrails or use the crosswalk arms. To exercise your
arms, shoulders, and back for a total body workout,
move the crosswalk arms forward and back as you
walk on the treadmill.
To select the information mode, hold down the Stop
button, insert the key into the console, and then release
the Stop button. When the information mode is selected, the following information will appear in the display:
To vary the intensity of your upper body exercise, the
resistance of the crosswalk arms can be adjusted. To
increase the resistance, turn the resistance knobs
clockwise; to decrease the resistance, turn the knobs
counterclockwise.
The lower left
corner of the display will show the
number of hours
that the treadmill
has been operated. The lower
right corner of the
display will show
the total number of miles or kilometers that the walking belt has moved.
Crosswalk
Arms
Resistance
Knobs
In addition, an “E” for English miles or an “M” for metric kilometers will appear in the lower left corner of the
display. To change the unit of measurement, press the
Speed increase button.
The console features a display demo mode, designed
to be used if the treadmill is displayed in a store.
While the demo mode is turned on, the console will
function normally when you plug in the power cord,
switch the reset/off circuit breaker to the reset position,
and insert the key into the console. However, when
you remove the key, the displays will remain lit, although the buttons will not function. If the demo mode
is turned on, a “d” will appear in the lower right corner
of the display while the information mode is selected.
To turn on or turn off the demo mode, press the Speed
decrease button.
To exit the information mode, remove the key from the
console.
20
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
lbs. (20 kg) to raise, lower, or move the treadmill.
1
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight as you raise the frame. Raise the frame
about halfway to the vertical position.
2. Raise the frame until the latch knob locks into the storage position. Make sure that the latch knob is locked
in the storage position.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° F (30° C).
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch
knob is locked in the storage position.
1. Hold a handrail and the frame and place one foot against
one of the wheels.
2. Pull the handrail back until the treadmill rolls freely on the
wheels. Carefully move the treadmill to the desired location. Never move the treadmill without tipping it back.
To reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot against a wheel, and carefully lower the
treadmill until it is resting in the storage position.
2
Frame
Latch
Knob
Frame
Handrail
Wheel
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2. Hold the upper end of the treadmill with your right hand. Pull the latch knob to the left and hold
it. It may be necessary to push the frame forward as you pull the knob to the left. Pivot the frame downward
and release the latch knob.
2. See drawing 1. Hold the metal frame firmly with both hands and lower it to the floor. CAUTION: Do not
grip only the plastic foot rails or drop the frame to the floor. Bend your legs and keep your back straight.
21
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 15). Use only a single-outlet surge suppressor that meets all of the specifications described on page 15. IMPORTANT: The treadmill is not
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
c
Tripped
Position
PROBLEM: The power turns off during use
Reset
Position
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 20 to turn off the demo mode.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG
THE POWER CORD. With the help of a second
person, carefully tip the Uprights (77, 92) down.
There may be three #8 x 2" Screws (14) in the bottom of the Belly Pan (73). If there are, remove
them. Note: A Phillips screwdriver with a shaft at
least 5 in. (13 cm) long is required. Then, raise the
Uprights.
a
77
73
92
14
14
22
Remove the three #8 x 3/4" Screws (1) and carefully pivot the Motor Hood (58) off.
58
Locate the Reed Switch (65) and the Magnet (40)
on the left side of the Pulley (41). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the #8 x 3/4" Pan Head Screw (15),
move the Reed Switch slightly, and then retighten
the Pan Head Screw. Reattach the Motor Hood
(not shown) with the #8 x 3/4" Screws (not shown).
Reattach the #8 x 2" Screws (not shown) if necessary. Run the treadmill for a few minutes to check
for a correct speed reading.
1/8 in.
15
Top
View
65
1
40
41
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 15.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
idler roller bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
b
2–3 in.
Idler Roller Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
23
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left idler roller bolt clockwise 1/2 of a
turn; if the walking belt has shifted to the right,
turn the idler roller bolt counterclockwise 1/2 of a
turn. Be careful not to overtighten the walking belt.
Then, plug in the power cord, insert the key, and
run the treadmill for a few minutes. Repeat until the
walking belt is centered.
b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD.
Using the hex key, turn both idler roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each
edge of the walking belt 2 to 3 in. (5 to 7 cm) off
the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for
a few minutes. Repeat until the walking belt is
properly tightened.
PROBLEM: The crosswalk arms squeak during use
SOLUTION: a. (Note: Correcting this problem requires a small amount of white marine grease, available at hardware
stores.) Remove the Resistance
Knob (88) from the resistance assembly. Remove the resistance assembly from the Left Upright (77) or
the Right Upright (92).
a
24
b
77
88
Apply a small amount of grease
around the Resistance Cone (85).
Insert the resistance assembly into
the Left Upright (77) or the Right
Upright (92). Then, tighten the
Resistance Knob (88) onto the resistance assembly.
a
85
Resistance
Assembly
92
EXERCISE GUIDELINES
WARNING: Before beginning this
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The pulse sensors are not medical devices.
Various factors may affect the accuracy of
heart rate readings. The pulse sensors are intended only as exercise aids in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
25
PART LIST—Model No. PFTL79008.0
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
23
6
6
4
4
4
1
4
3
3
4
4
7
3
10
2
2
2
2
1
1
2
7
8
2
4
2
2
4
4
3
2
1
1
2
2
2
2
1
1
1
1
1
1
1
1
1
1
2
1
Description
Key No. Qty.
#8 x 3/4" Screw
#8 x 1/2" Screw
#8 x 1 1/2" Screw
#10 x 3/4" Screw
5/16" x 1 3/4" Bolt
#8 x 1" Tek Screw
3/8" x 1 3/4" Bolt
3/8" x 4" Bolt
3/8" x 2" Bolt
3/8" Nut
3/8" Star Washer
#10 Star Washer
#8 x 3/4" Tek Screw
#8 x 2" Screw
#8 x 3/4" Pan Head Screw
5/16" x 1 1/2" Bolt
5/16" x 3 5/8" Bolt
3/8" x 1" Bolt
Idler Roller Bolt
3/8" x 1 3/4" Motor Bolt
3/8" x 1 1/2" Motor Bolt
3/8" x 3/4" Bolt
1/2" Ground Screw
1 1/4" Foot Rail Screw
1/4" x 3/8" Bolt
Belt Guide Screw
1/4" Washer
1/4" Split Washer
3/8" Jam Nut
5/16" Flange Nut
Hood Clip
Foot Rail Decal
Left Foot Rail
Warning Decal
Platform Cushion
Belt Guide
Frame Cap
Frame Spacer
1/4" x 1" Bolt
Magnet
Drive Roller/Pulley
Walking Platform
Walking Belt
Latch Cap
Storage Latch
Latch Knob
Right Foot Rail
Frame
Roller Bracket
Right Rear Foot
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
26
1
1
1
1
1
1
1
1
1
1
1
1
3
2
1
1
1
2
1
1
1
1
1
8
2
4
1
1
2
2
2
2
2
2
2
2
2
2
2
2
1
1
2
1
4
1
4
2
2
1
Description
Idler Roller Ground Wire
Hex Key
Console Wire Tie
Left Rear Foot
Right Handrail Cover
Idler Roller
Hood Accent
Motor Hood
Lift Frame
Drive Belt
Drive Motor
Lift Frame Ground Wire
Wire Tie
Top Handrail Spacer
Reed Switch
Reed Switch Clamp
Controller
Bottom Handrail Spacer
Controller Ground Wire
Power Cord
Power Cord Grommet
Reset/Off Circuit Breaker
Belly Pan
8" Tie
15 1/2" Wire Tie
Releasable Tie
Left Upright
Left Handrail Cover
Handrail Cap
Handrail
Crosswalk Arm Handgrip
Crosswalk Arm
Upright Cap
Upright Insert
Resistance Cone
Resistance Cone Insert
Arm Insert
Resistance Knob
Small Cap
3/8" x 4 3/4" Bolt
Wire Harness
Right Upright
Base Cap
Left Upright Spacer
Bolt Spacer
Base
Base Foot
Base Foot Spacer
Wheel
Right Upright Spacer
R0109A
Key No. Qty.
101
102
103
104
105
106
107
108
109
2
1
1
1
1
1
1
1
1
Description
Key No. Qty.
Caution Decal
Incline Motor
Incline Motor Spacer
Console Fan
Console
Key/Clip
Console Back
Accessory Door
Console Ground Wire
110
111
112
113
114
115
*
*
*
1
1
1
1
1
1
–
–
–
Description
Pulse Bar
Incline Motor Wire
#8 x 1/2" Console Ground Screw
Chest Pulse Receiver
Chest Pulse Strap
Chest Pulse Sensor
4" Red Wire, M/F
4" Black Wire, M/F
Userʼs Manual
Note: Specifications are subject to change without notice. See the back cover of this manual for information about
ordering replacement parts. *These parts are not illustrated.
27
28
19
28
27
3
49
24
23
52
15
54
30
56
17
34
24
19
33
23
28
27
35
32
3
15
15
49
30
26
36
50
51
17
24
30
24
24
16
48
42
10
47
37
38
24
15
43
41
40
9
46
35
24
15
45
26
16
32
36
30
39
24
37
38
44
7
EXPLODED DRAWING A—Model No. PFTL79008.0
R0109A
EXPLODED DRAWING B—Model No. PFTL79008.0
31
1
31
1
1
31
58
57
25
59
18
60
23
61
65
67
66
76
69
13
13
14
74
73
13
14
14
29
63
23
18
2
13
15
75
23
62
23
70
71
72
R0109A
EXPLODED DRAWING C—Model No. PFTL79008.0
R0109A
81
5
83
13
64
78
2
68
80
3
82
82
77
84
1
8
86
11
9
10
1
87
95
101
96
98
97
6
21
29
29
93
29
89
90
89
22
87
1
91
111
85
86
9
30
97
6
92
84
22
101
6
98
3
1
97
10
99
83
91
6
102
103
90
97
20
68
2
85
94
80
79
55
13
64
5
2
79
88
99
81
2
29
88
93
11
8
95
100
95
11
8
EXPLODED DRAWING D—Model No. PFTL79008.0
1
106
105
115
114
1
107
113
1
1
4
12
108
1
1
1
112
109
1
15
1
110
1
1
31
4
12
104
53
1
R0109A
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The drive motor is warranted for twenty-five (25)
years from the date of purchase. Parts and labor are warranted for ninety (90) days from the date of purchase.
This warranty extends only to the original purchaser. ICONʼs obligation under this warranty is limited to
repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customerʼs responsibility. For
replacement parts shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to any damage to a product caused by or attributable to freight damage,
abuse, misuse, improper or abnormal usage, or repairs not provided by an ICON authorized service center; products used for commercial or rental purposes; or products used as store display models. No other
warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 275643 R0109A
Printed in USA © 2009 ICON IP, Inc.