User manual
Dishwasher
DX 103
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use of the appliance _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use of rinse aid _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Loading cutlery and dishes _ _ _ _ _ _ _ _ _ _ _ _
Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Select and start a washing program _ _ _ _ _ _ _ _
2
3
4
4
5
5
7
8
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8
What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Water connection _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12
Electrical connection _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13
Warranty _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13
Subject to change without notice
Safety information
For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the
appliance even if you move or sell it. Users must fully
know the operation and safety features of the appliance.
•
•
Correct use
• Only use the appliance to clean household utensils
that are suitable for dishwashers.
• Do not put solvents in the appliance. Risk of explosion.
• Put the knives and all items with sharp points in the
cutlery basket with their points down. If not, put them
in a horizontal position in the upper basket.
• Use only products specified for dishwashers (detergent, salt, rinse aid).
• If you open the door while the appliance is in operation, hot steam can escape. Risk of skin burns.
• Do not remove dishes from the dishwasher before
the end of the washing program.
• When the washing program is completed, disconnect the mains plug from the mains socket and close
the water tap.
• Only an authorised service engineer can repair this
appliance. Use only original spare parts.
• Do not do repairs yourself to prevent injury and
damage to the appliance. Always contact the Customer Care Centre.
General safety
• Dishwasher detergents are very dangerous. Be
careful they do not touch eyes, mouth and skin. Keep
2
•
•
•
the children away from the appliance when the door
is open.
Obey the safety instructions from the manufacturer
of the dishwasher detergent to prevent burns to
eyes, mouth and throat.
Only put detergent in the dispenser before you start
a washing program. Make sure that the detergent
dispenser is empty at the end of the washing program.
Do not drink the water from the dishwasher. Detergent residues can stay in your appliance.
Always close the door when you do not use the appliance to prevent injury and not to stumble over the
open door.
Do not sit or stand on the open door.
Child safety
• Children or infirm persons must not use this appliance. They must get supervision to make sure that
they do not play with the appliance.
• Keep all the packaging away from children. There is
a risk of suffocation.
• Keep all detergents in a safe area. Do not let children
touch the detergents.
• Keep the children and pets away from the appliance
when the door is open.
Installation
• Make sure that the appliance is not damaged because of transport. Do not connect a damaged appliance. If necessary, contact the supplier.
• Remove all packaging before first use.
• A qualified and competent person must do the electrical installation.
• A qualified and competent person must do the
plumbing installation.
• Do not change the specifications or modify this product. Risk of injury and damage to the appliance.
• Do not use the appliance:
– if the mains cable or water hoses are damaged,
– if the control panel, worktop or plinth area are
damaged so that you can get access to the inner
side of the appliance.
Contact your local Customer Care Centre.
• Do not drill into the sides of the appliance otherwise
damage to hydraulic and electrical components may
occur.
Warning! Carefully obey the instructions for
electrical and water connections.
Control panel
1
2
3
4
5
Program knob
Start/cancel button
Indicator light 'Finished'
On/off indicator light
Program marker
Indicator lights
Finished
Comes on when the washing program is completed. It also has
the auxiliary functions of alarm if the appliance has a malfunction.
Program knob and on/off indicator light
• To set a washing program, turn the program knob
clockwise or anticlockwise. The program marker on
the program knob must agree with one of the washing program on the control panel.
– The on/off indicator light comes on (position ON).
• To set the appliance to the off position, turn the program knob until the program marker agrees with the
on/off indicator light.
– The on/off indicator light goes off (position OFF).
3
Washing programmes
Program
Degree of soil
Type of load
Program description
Pots
Heavy soil
Crockery, cutlery,
pots and pans
Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Drying
Regular Plus
Normal soil
Crockery and cutlery
Prewash
Main wash up to 65°C
2 intermediate rinses
Final rinse
Drying
Quick 30 1)
Normal or light soil
Crockery and cutlery
(Partial load)
Main wash up to 65°C
Final rinse
Regular Eco 2)
Normal soil
Crockery and cutlery
Prewash
Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying
Rinse & Hold
Any
Partial load (to be
1 cold rinse (to prevent food
completed later in the scraps to bond).
day).
Detergent is not necessary with
this program.
1) This is the perfect daily program to clean a partial load. Ideal for a family of 4 persons who only want to load breakfast and
dinner crockery and cutlery.
2) Test program for test institutes. Please refer to separate leaflet supplied, for test data.
Consumption values
Program
Duration (in minutes)
Energy (in kWh)
Water (in litres)
Pots
85 - 95
1,8 - 2,0
22 - 25
Regular Plus
100 - 115
1,5 - 1,7
23 - 25
Quick 30
30
0,9
9
Regular Eco
90 - 100
0,83 - 0,91
16 - 18
Rinse & Hold
12
0,1
5
The pressure and temperature of the water, the
variations of power supply and the quantity of
dishes can change these values.
Use of the appliance
Refer to specified instructions for each step of the procedure.
4
1. Fill the rinse aid dispenser with rinse aid.
2. Load cutlery and dishes into the dishwasher.
3. Set the correct washing program for the type of
load and soil.
4. Fill the detergent dispenser with the correct quantity of detergent.
5. Start the washing program.
Use of rinse aid
Caution! Only use rinse aid specified for
dishwashers.
Follow these steps to fill the rinse aid dispenser:
Caution! Do not fill the rinse aid dispenser with
other products (e.g. dishwasher cleaning agent,
liquid detergent). There can cause damage to the
appliance.
Adjusting the rinse aid dosage
AX
+
M
1
1
2
3
4
The rinse aid is set at the
factory at position 3.
To increase or decrease
the dosage refer to 'What
to do if...'
2
Wash hands to remove any residue of rinse aid
from skin.
AX
+
M
1
2
3
4
4
3
Fill when the rinse aid indicator (B) becomes
clear.
AX
+
M
1
2
3
4
5
Loading cutlery and dishes
Helpful hints and tips
Caution! Only use the appliance for household
utensils that are suitable for dishwashers.
• Before you load cutlery and dishes, do these steps:
– Remove all food remainings and debris.
– Make burnt, remaining food in pans soft.
Do not use the appliance to clean objects that can absorb water (sponges, household cloths, etc.).
5
• While you load cutlery and dishes, do these steps:
– Load hollow items (e.g. cups, glasses and pans)
with the opening down.
– Make sure that water does not collect in the container or in a deep base.
– Make sure that cutlery and dishes do not lie inside
one another.
– Make sure that cutlery and dishes do not cover
other cutlery and dishes.
– Make sure that glasses do not touch other
glasses.
– Put small objects in the cutlery basket.
• Plastic items and pans with non-stick coatings can
retain water droplets. Plastic items do not dry as well
as porcelain and steel items.
• Put light items in the upper basket. Make sure that
the items do not move.
Caution! Make sure that the spray arms can
move freely before you start a washing program.
Warning! Always close the door after you load
or unload the appliance. An open door can be
dangerous.
Use the cutlery grid for best washing results. If the dimensions of the cutlery prevent use of the cutlery grid,
remove it.
1
2
Arrange the items to let For longer items, fold the
water touch all surfaces. cup racks up.
Prevent to put plates in the first three sectors in
the front part of the basket. Make sure the plates
tilt forward.
Adjustment of the height of the upper basket
If you put large plates in the lower basket, first move
the upper basket to a upper position.
Warning! Adjust the height before you load the
upper basket.
Maximum height of the dishes in :
1
Arrange service dishes
and large lids around the
edge of the lower basket.
upper basket
lower basket
Upper position
20 cm
31 cm
Lower position
24 cm
27 cm
2
1
1
6
2
2
Follow these steps to move the upper basket to the
upper or lower position:
1. Move the front runner stops (A) out.
2. Pull the basket out.
3. Put the basket in the upper or lower position.
4. Replace the front runner stops (A) in their initial
position.
Caution! If the basket is in the upper position,
do not put cups on the cup racks.
Use of detergent
Only use detergents (powder, liquid or tablet) that
are suitable for dishwashers.
Follow the data on the packaging:
• dosage recommended by the manufacturer,
• storage recommendations.
Do not use more than the correct quantity of detergent to decrease pollution.
1
2
Different brands of detergent dissolve in different
times. Some detergent tablets do not have the
best cleaning results during short washing programs.
Use long washing programs when you use detergent
tablets to fully remove the detergent.
Use of combi detergent tablets
These products are detergents with a combined cleaning and rinsing functions. They can contain also other
cleaning agents.
Refer to the instructions from the manufacturer for the
use of these products.
With tablets that contain rinse aid:
• set the lowest position for the rinse aid dosage,
• do not put rinse aid in the rinse aid dispenser. In this
condition rinse aid indicator light is always on when
you switch on the appliance.
.
Do these steps if the drying results are not satisfactory:
1. Fill the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
If you go back to use normal detergents again, fill
the rinse aid dispenser and adjust the rinse aid
dosage.
3
Fill the detergent dispenser (A) with detergent.
5
4
If you use a washing program with prewash
phase, put more detergent in the prewash detergent compartment (B).
6
7
Select and start a washing program
Do these steps to set and start a washing program:
1. Close the door.
2. Turn the program knob to set the washing program.
Refer to the chapter 'Washing programs'.
– The on/off indicator light comes on.
3. Press the start/cancel button.
– The washing program starts automatically.
– The start/cancel indicator light comes on.
When the washing program operates, you cannot
change the program. Cancel the washing program.
Warning! Only interrupt or cancel a washing
program if necessary.
Attention! Open the door carefully. Hot steam and
water can escape.
Cancelling a washing program
• Press and hold the start/cancel button until the start/
cancel indicator light goes off.
The washing program is cancelled.
At this time you can do these steps:
1. Switch off the appliance.
2. Set a new washing program.
Fill the detergent dispenser with detergent before
you set a new washing program.
Interrupting a washing program
Open the door.
• The program stops.
Close the door.
• The program continues from the point of interruption.
End of the washing program
•
•
1.
2.
3.
The appliance stops automatically.
The 'Finished' indicator light comes on.
Switch off the appliance.
Open the door.
For better drying results, keep the door ajar for
some minutes before you remove the dishes.
Let the dishes cool down before you remove them from
the appliance. Hot dishes are easily damaged.
Removing the load
• First remove items from the lower basket, then from
the upper basket.
• There can be water on the sides and door of the
appliance. Stainless steel becomes cool more quickly than the dishes.
Care and cleaning
Warning! Switch the appliance off before you
clean it.
Cleaning the filters
Important! Do not use the appliance without the filters.
Make sure that the installation of the filters is correct.
Incorrect installation will cause unsatisfactory washing
results and damage to the appliance.
1
8
2
Fully clean the filters A, B
and C below running water.
tergents. Do not use abrasive products, scouring pads
or solvents (acetone etc.).
Internal cleaning
Do an inspection at intervals of 3 months. Set a washing
program for heavily soiled dishes. Use detergent, but
do not put dishes in the appliance.
Long periods of non-operation
3
To remove filters B and
C, turn the handle approximately 1/4 anticlockwise.
4
Remove the flat filter A
from the bottom of the appliance.
Do these steps when you do not use the appliance for
a long period:
1. Disconnect the mains plug from the mains socket.
2. Close the water tap.
3. Keep the door open to prevent unpleasant smells.
4. Keep the inner side of the appliance clean.
Frost precautions
Caution! Do not install the appliance where the
temperature is below 0 °C. The manufacturer is
not responsible for damage because of frost.
5
Put the filter A in the bottom of the appliance. Install the flat filter correctly
under the two guides D.
6
Put the filter system in position. To lock the filter
system, turn the handle
clockwise until it locks in
position
Important! Do not remove the spray arms.
If the holes in the spray arms become clogged, remove
remaining parts of soil with a cocktail stick.
If not possible, empty the appliance and close the door.
Disconnect the water inlet hose and remove water from
the water inlet hose.
Moving the machine
Do these steps to move the appliance:
1. Disconnect the mains plug from the mains socket.
2. Close the water tap.
3. Remove the appliance and the hoses.
4. Do not tilt the appliance during transport.
External cleaning
Clean the external surfaces of the appliance and control panel with a damp soft cloth. Only use neutral de-
What to do if…
The appliance does not start or stops during operation.
If there is a fault, first try to find a solution to the problem
yourself. Refer to following charts. If you cannot find a
solution to the problem yourself, contact your dealer or
the Customer Care Centre.
Warning! Switch the appliance off before you do
the suggested corrective actions.
9
Fault code and malfunction
Possible cause and solution
• continuous flash of the start/cancel
• The water tap is blocked or furred with limescale.
indicator light
Clean the water tap.
• 1 flash of the 'Finished' indicator light • The water tap is closed.
The appliance does not fill with water
Open the water tap.
• The filter in the water inlet hose is blocked.
Clean the filter.
• The connection of the water inlet hose is not correct. The hose
can be kinked or squashed.
Make sure that the connection is correct.
• continuous flash of the start/cancel
indicator light
• 2 flashes of the 'Finished' indicator
light
The appliance will not drain
• There is a blockage in the sink spigot.
Clean the sink spigot.
• The connection of the water drain hose is not correct. The hose
can be kinked or squashed.
Make sure that the connection is correct.
The program does not start
• The appliance door is not closed.
Close the door.
• Mains plug is not connected.
Plug-in appliance to the mains.
• The fuse has blown out in the household fuse box.
Replace the fuse.
After the check, switch on the appliance. The program
continues from the point of interruption. If the malfunction shows again, contact your Customer Care Centre.
For other fault codes, not described in the chart, contact
your Customer Care Centre.
These data are necessary to help you quickly and correctly:
• Model (Mod.)
• Product number (PNC)
• Serial number (S.N.)
For these data, refer to the rating plate.
Write the necessary data here:
Model description : ..........
Product number : ..........
Serial number : ..........
The cleaning results are not satisfactory
The dishes are not clean
• The selected washing program is not applicable for the type of load and
soil.
• The baskets are loaded incorrectly so that water cannot reach all surfaces.
• Spray arms do not turn freely because of incorrect arrangement of the
load.
• The filters are dirty or not correctly installed.
• The quantity of detergent is too little or missing.
The dishes are wet and dull
• No rinse aid has been used.
• The rinse aid dispenser is empty.
10
The cleaning results are not satisfactory
There are streaks, milky spots or • Decrease the rinse aid dosage.
a bluish coating on glasses and
dishes
Dry water drop stains on glasses • Increase rinse aid dosage.
and dishes
• The detergent can be the cause.
Technical data
Dimensions
Width (mm)
596
Height (mm)
850
Depth (mm)
610
Electrical connection - Voltage Overall power - Fuse
Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher door.
Water supply pressure
Minimum
50 kPa (7 psi)
Maximum
800 kPa (116 psi)
Capacity
Place settings
12
Environment concerns
The packaging materials are environmentally friendly
and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Discard the
packaging materials in the applicable container at the
community waste disposal facilities.
Warning! To discard the appliance, follow the
procedure:
• Pull the mains plug out of the socket.
• Cut off the mains cable and mains plug and discard
them.
• Discard the door catch. This prevents children closing themselves inside the appliance and endangering their lives.
Old appliance
Make sure that the appliance goes to the applicable
collection point for recycling.
Make sure that this appliance is discarded correctly.
Inappropriate waste discard of the appliance causes
negative consequences for the environment and human health.
For more information about the recycling of this appliance, contact your local city office, your household
waste disposal service or the shop where you purchased the appliance.
Installation
Fitting under a counter
Warning! Make sure that mains plug is
disconnected from the mains socket during
installation.
Put the appliance adjacent to a water tap and a water
drain.
The plinth on freestanding appliance is not adjustable.
Do not remove the appliance worktop if you want to use
the dishwasher as a freestanding appliance.
Remove the appliance worktop to install it under a sink
unit or a kitchen worktop.
Make sure that the dimensions of the recess agree with
the given dimensions.
11
the door does not catch on the sides of the cabinet. If
the door does not close correctly, loosen or tighten the
adjustable feet until the appliance is level.
Adhesive steam protection foil
If the worktop is removed, fit the steam protection onto
the front part of the kitchen cabinet benchtop.
1
3
2
4
The steam protection foil is not supplied with freestanding models, but can be purchased from
Electrolux Spare Parts.
Adjusting the level of the appliance
Make sure that the appliance is level to close and seal
the door correctly. If the level of the appliance is correct,
Water connection
Water inlet hose
Fit the hose nut correctly to prevent water leaks.
Connect the appliance to a cold water supply.
Connect the inlet hose to a water tap with an external
BSP thread spout of 3/4”.
Caution! Do not connect the appliance to new
pipes or pipes that have been not used for a long
time. Let the water run for some minutes, then connect
the inlet hose.
Inlet water supply
• Cold water pressure: 800 kPa max - 50 kPa min.
• Water flow rate 10 L / minute min.
• If cold water pressure is in excess of 800 kPa, a
pressure reducing valve should be used. Check for
leaks.
Caution! Always use new hoses when you
connect the appliance to the water mains. Old
hoses must not be used. The water inlet hose must be
examined at an interval of twelve months for
deterioration and replaced if necessary.
The water pressure must be in the limits (refer to 'Technical data'). Make sure that the local water authority
gives you the average mains pressure in your area.
Make sure that there are no kinks in the water inlet hose
and that the water inlet hose is not squashed or entangled.
12
Water drain hose
The highest point of the drain hose must be no more
than 60 cm from the floor and must have a continuous
fall.
The drain hose can be lengthened using additional
lengths and connectors. These must be purchased
from Electrolux Spare Parts. The extension length must
not exceed 2 metres.
The drain hose must be free of kinks and obstructions.
Remove the sink plug when the appliance drains the
water to prevent that the water goes back into the appliance.
If you connect the water drain hose to a trap spigot
under the sink, remove the plastic membrane. If you do
not remove the membrane, remaining food can cause
a blockage in the drain hose spigot.
Caution! Ensure that hoses are not crushed or
kinked under or behind the appliance.
The appliance has a security feature to prevent dirty
water going back into the appliance. If, the spigot of the
sink has a 'non-return valve', this valve can cause the
appliance to drain incorrectly. Remove the non-return
valve.
Make sure that the water couplings are tight to prevent
water leakage.
Caution! Once connected the inlet hose to the
water tap, turn the tap on and check that there
are no leaks.
Electrical connection
Warning! Safety standards require the appliance
to be earthed.
Prior to using the appliance for the first time, ensure
that the rated voltage and type of supply on the rating
plate match that of the supply where the appliance is
to be installed.
The fuse rating is also to be found on the rating plate.
Always plug the mains plug onto a correctly installed
approved socket.
Do not use multi-ways plugs, connectors and extension
cables. This can constitute a fire hazard through
overheating.
If necessary, have the domestic wiring system socket
replaced. If the mains cable has to be replaced, contact
your local Customer Care centre.
The mains plug must be accessible after the appliance
has been installed.
Never unplug the appliance by pulling on the cable.
Always pull the plug.
Test the appliance. Run a quick washing program and
ensure that the appliance fills with water, washes and
drains with no leaks.
The manufacturer accepts no liability for failure to
observe the above safety precautions.
Warranty
FOR SALES IN AUSTRALIA AND NEW ZEALAND
This document sets out the terms and conditions
of product warranties for Electrolux branded appliances. It is an important document. Please keep
it with your proof of purchase documents in a safe
place for future reference should you require service for your Electrolux appliance. General Terms
and Conditions
1. In this warranty
– Electrolux' means Electrolux Home Products
Pty Ltd ABN 51 004 762 341 in respect of Appliances purchased in Australia and Electrolux
(NZ) Limited in respect of Appliances purchased in New Zealand;
– 'Appliance' means any Electrolux product purchased by you accompanied by this document;
– 'Warranty Period' means
i) where you use the Appliance for personal,
domestic or household purposes in Australia
the period of 24 months and in New Zealand
the period of 24 months;
ii) where you use the Appliance for commercial
purposes, in Australia the period of 0 months
and in New Zealand the period of 0 months, (if
the period stated is 0 months you are not covered by this product warranty) following the
date of original purchase of the Appliance;
13
2.
3.
4.
5.
6.
7.
8.
14
– 'you' means the purchaser of the Appliance not
having purchased the appliance for re-sale,
and 'your' has a corresponding meaning.
This warranty only applies to Appliances purchased and used in Australia or New Zealand and
is in addition to (and does not exclude, restrict, or
modify in any way) any non-excludable statutory
warranties in Australia or New Zealand.
Electrolux warrants that, when dispatched from an
Electrolux warehouse, the Appliance is free from
defects in materials and workmanship for the Warranty Period.
During the Warranty Period Electrolux or its Authorised Service Centre will, at no extra charge if
your appliance is readily accessible without special equipment, and subject to these terms and
conditions, repair or replace any parts which it
considers to be defective. You agree that any replaced Appliances or parts become the property
of Electrolux. This warranty does not apply to light
globes, batteries, filters or similar perishable
parts.
Parts and Appliances not supplied by Electrolux
are not covered by this warranty.
Where you are within an Electrolux service area,
this warranty covers the cost of transport of the
Appliance to and from Authorised Service Centres
of Electrolux and travelling costs for representatives of the Authorised Service Centre to and from
your home or business. If you are outside an Electrolux service area, you will bear these costs. For
information about whether you are within an Electrolux service area, please phone 13 13 49 in
Australia, or 0800 10 66 10 in New Zealand.
Proof of purchase is required before you can make
a claim under this warranty.
You may not make a claim under this warranty
unless the defect claimed is due to faulty or defective parts or workmanship. Electrolux is not liable in the following situations (which are not exhaustive):
– The Appliance is damaged by
i) accident
ii) misuse or abuse, including failure to properly
maintain or service
iii) normal wear and tear
iv) power surges, electrical storm damage or
incorrect power supply
v) incomplete or improper installation
vi) incorrect, improper or inappropriate operation
vii) insect or vermin infestation.
– The Appliance is modified without authority
from Electrolux in writing.
– The Appliance's serial number or warranty seal
has been removed or defaced.
– The Appliance was serviced or repaired by
anyone other than Electrolux or its Authorised
Service Centres.
9. This warranty, the contract to which it relates and
the relationship between you and Electrolux are
governed by the law applicable in the Australian
State where the Appliance was purchased or the
law applicable in New Zealand if the Appliance
was purchased in New Zealand. Where the Appliance was purchased in New Zealand for business purposes the Consumer Guarantee Act does
not apply.
Limitation of Liability
10. To the extent permitted by law:
– Electrolux excludes all warranties other than as
contained in this document;
– Electrolux shall not be liable for any loss or
damage whether direct or indirect or consequential arising from your purchase, use or
non-use of the Appliance.
11. Provisions of the Trade Practices Act and State
consumer legislation in Australia, and the Consumer Guarantees Act, the Sale of Goods Act and
the Fair Trading Act in New Zealand, imply warranties or conditions, or impose obligations, upon
Electrolux which cannot be excluded, restricted or
modified. To the extent permitted by law, the liability of Electrolux (if any) arising out of or in relation to the Appliance or any services supplied by
Electrolux shall be limited (where it is fair and reasonable to do so),:
– in the case of Appliances, at its option, to the
replacement or repair of the Appliances or the
supply of equivalent products or the payment
of the cost of replacing the Appliances or having
the Appliances repaired or of acquiring equivalent Appliances. Upon being replaced, parts
and Appliances become the property of Electrolux; or
– in the case of services, at its option, to the supply of the services again or the payment of the
cost of having the services re-supplied;
and in the case of Appliances or services supplied
in New Zealand, loss or damage whether direct or
indirect or consequential that is reasonably foreseeable.
Privacy
You acknowledge that in the event that you make a
warranty claim it will be necessary for Electrolux and
FOR SERVICE
OR TO FIND THE ADDRESS OF
YOUR NEAREST STATE SERVICE CENTRE IN AUSTRALIA
Please call 13 13 4 9
its Authorised Service Centres to exchange information
in relation to you to enable Electrolux to meet its obligations under this warranty.
Important Notice
Before Calling a Service Technician please check carefully the operating instructions, service booklet and the
warranty terms and conditions.
SERVICE AUSTRALIA
ELECTROLUX HOME PRODUCTS
FOR SPARE PARTS
OR TO FIND THE ADDRESS OF
YOUR NEAREST STATE SPARE
PARTS CENTRE IN AUSTRALIA
Please call 13 13 50
For the cost of a local call (Australia only)
For the cost of a local call (Australia only)
FOR SERVICE
SERVICE NEW ZEALAND
OR TO FIND THE ADDRESS OF
YOUR NEAREST AUTHORISED ELECTROLUX HOME PRODSERVICE CENTRE IN NEW ZEA- UCTS
LAND
Free call 0800 10 66 10
FOR SPARE PARTS
OR TO FIND THE ADDRESS OF
YOUR NEAREST SPARE PARTS
CENTRE IN NEW ZEALAND
Free call 0800 10 66 20
(New Zealand only)
(New Zealand only)
15
www.electrolux.com
www.dishlex.com.au
156998835-05-072009