R-320CD/CK/CW
R-330CK/CW
SERVICE MANUAL
S2904R320CPW/
MICROWAVE OVEN
MODELS
COOK SENSO
R LBS KG
DEF HELP
REHEAT
SENSOR
CUSTOM
SENS
HELP
OR C
OOK
Baked
Potatoes
Popcorn
Frozen
Vegetable
s
Ground
Meat
Rice
Chicken
Breast
Frozen
Entrees
Fresh
Vegetable
s
Fish/
Seafood
NT A
CTIO
Fresh
N
Rolls/Muff
ins Beverage
Frozen
Rolls/Muff
COMP
ins
U DEF
ROST
Ground
Meat
Steaks/
Chops
Chicken
Pieces
INSTA
1
2
6
7
Kitchen
Timer
Power
Level
3
4
8
9
Clock
Stop
Clear
5
o
Minute
Plus
Start
R-320CD
R-320CK
R-320CW
R-330CK
R-330CW
In the interest of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.
R-320CW
WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage and
current, contact with following parts may result in a severe,
possibly fatal, electrical shock. (High Voltage Capacitor, High
Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..)
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ................... INSIDE FRONT COVER
BEFORE SERVICING ......................................................................................................INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL ................................................................................................................ 1
MICROWAVE MEASUREMENT PROCEDURE ................................................................................................... 2
FOREWORD AND WARNING ............................................................................................................................... 3
PRODUCT SPECIFICATIONS .............................................................................................................................. 4
GENERAL INFORMATION ................................................................................................................................... 4
OPERATION .......................................................................................................................................................... 6
TROUBLESHOOTING GUIDE ............................................................................................................................ 10
TEST PROCEDURE ............................................................................................................................................ 12
TOUCH CONTROL PANEL ................................................................................................................................. 21
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE ................................................................ 29
PICTORIAL DIAGRAM ........................................................................................................................................ 35
POWER UNIT CIRCUIT ...................................................................................................................................... 36
CPU UNIT CIRCUIT ............................................................................................................................................ 37
PRINTED WIRING BOARD ................................................................................................................................. 40
PARTS LIST ........................................................................................................................................................ 41
PACKING AND ACCESSORIES ......................................................................................................................... 43
SHARP CORPORATION
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
R-320CD/CK/CW
R-330CK/CW
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3)
seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and
latches, (5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave
generation and transmission systems shall be repaired, replaced, or adjusted by procedures described
in this manual before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner.
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave
Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS
CORPORATION immediately @1-800-237-4277.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact SHARP ELECTRONICS CORPORATION and Food and Drug Administration's
Center for Devices and Radiological Health immediately.
Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit found
with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use the unit
until the oven has been brought into compliance.
SENSOR
DEFROST
COOK
Popcorn
Fresh
vegetables
Ground
meat
Frozen
entrees
Kitchen
Timer
Power
Level
R-330CW
Sensor
reheat
Rice
Poultry
Frozen
snacks
Clock
Stop
Clear
HELP
Custom
help
Baked
potatoes
Fish/
seafood
Frozen
vegetables
Minute
Plus
Start
Touch On
R-320CD/CK/CW
R-330CK/CW
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with
following parts may result in a severe, possibly
fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all
instructions.
Don't Touch !
Danger High Voltage
When the testing is completed,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power
transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is
installed.
7. Run the oven and check all functions.
Before Servicing
1. Disconnect the power supply cord
remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
, and then
WARNING:RISK OF ELECTRIC SHOCK.
DISCHARGE THE HIGH-VOLTAGE
CAPACITOR BEFORE SERVICING.
The high-voltage capacitor remains charged about 60
seconds after the oven has been switched off. Wait for 60
seconds and then short-circuit the connection of the highvoltage capacitor (that is the connecting lead of the highvoltage rectifier) against the chassis with the use of an
insulated screwdriver.
After repairing
1. Reconnect all leads removed from components during
testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is
installed.
4. Run the oven and check all functions.
Whenever troubleshooting is performed the power supply
must be disconnected. It may in, some cases, be necessary
to connect the power supply after the outer case has been
removed, in this event,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power
transformer.
5. Ensure that the leads remain isolated from other
components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a cup
of cold water on the oven turntable, close the door and set
the power to HIGH and set the microwave timer for two (2)
minutes. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water
remains cold carry out Before Servicing procedure and reexamine the connections to the component being tested.
When all service work is completed and the oven is fully
assembled, the microwave power output should be checked
and a microwave leakage test should be carried out.
1
R-320CD/CK/CW
R-330CK/CW
MICROWAVE MEASUREMENT PROCEDURE
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches Primary interlock relay and door sensing switch shall prevent microwave radiation emission in
excess of the requirement as above mentioned, secondary interlock switch shall prevent microwave radiation emission
in excess of 5 mW/cm2 at any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard for
microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5˚C (68˚F) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.)
and made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode.
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed,
replace it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement)
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on
the meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2,
and that the secondary interlock switch does turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2
R-320CD/CK/CW
R-330CK/CW
SERVICE MANUAL
PRODUCT DESCRIPTION
MICROWAVE OVEN
R-320CD/ R-320CK/ R-320CW/ R-330CK/ R-330CW
GENERAL INFORMATION
FOREWORD
This Manual has been prepared to provide Sharp Electronics Corp.
Service Personnel with Operation and Service Information for the
SHARP MICROWAVE OVEN, R-320CD, R-320CK, R-320CW, R330CK, R-330CW.
It is recommended that service personnel carefully study the entire
text of this manual so that they will be qualified to render satisfactory
customer service.
Check the interlock switches and the door seal carefully. Special
attention should be given to avoid electrical shock and microwave
radiation hazard.
WARNING
Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
Servicing and repair work must be carried out only by trained service
personnel.
DANGER
Certain initial parts are intentionally not grounded and present
a risk of electrical shock only during servicing. Service
personnel - Do not contact the following parts while the
appliance is energized;
High Voltage Capacitor, Power Transformer, Magnetron, High
Voltage Rectifier Assembly, High Voltage Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “*” on parts list are used at voltages more than
250V.
Removal of the outer wrap gives access to voltage above 250V.
All the parts marked “∆” on parts list may cause undue microwave
exposure, by themselves, or when they are damaged, loosened
or removed.
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH,
NEW JERSEY 07430-2135
3
OPERATION
TROUBLESHOOTING GUIDE AND
TEST PROCEDURE
TOUCH CONTROL PANEL
COMPONENT REPLACEMENT
AND ADJUSTMENT PROCEDURE
WIRING DIAGRAM
PARTS LIST
R-320CD/CK/CW
R-330CK/CW
SPECIFICATION
ITEM
Power Requirements
Power Output
DESCRIPTION
120 Volts / 13 Amperes
60 Hertz
Single phase, 3 wire grounded
1100 watts (IEC-705 TEST PROCEDURE)
Operating frequency of 2450MHz
Case Dimensions
Width 20-1/2"
Height 11-7/8"
Depth 16-7/8"
Cooking Cavity Dimensions
Width 14-3/4"
Height 8-3/4"
Depth 15-3/4"
Touch Control System
Clock ( 1:00 - 12:59 )
Timer (0 - 99 min. 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
P-HI ......... Full power throughout the cooking time
P-90 ...................................................................... approx. 90% of Full Power
P-80 ...................................................................... approx. 80% of Full Power
P-70 ...................................................................... approx. 70% of Full Power
P-60 ...................................................................... approx. 60% of Full Power
P-50 ...................................................................... approx. 50% of Full Power
P-40 ...................................................................... approx. 40% of Full Power
P-30 ...................................................................... approx. 30% of Full Power
P-20 ...................................................................... approx. 20% of Full Power
P-10 ...................................................................... approx. 10% of Full Power
P-0 ...................................................... No power throughout the cooking time
REHEAT SENSOR pad, CUSTOM HELP pad, COMPU DEFROST pads
R-320CD SENSOR COOK pads, INSTANT ACTION pads
R-320CK Number selection pads, Kitchen Timer pad, Clock pad,
R-320CW Minute Plus pad, Power Level pad, Stop/Clear pad, Start pad
Sensor Cooking pads, Breakfast Bar pad, Lunch on the Run pad
R-330CK One Dish Dinners pad, Super Defrost pad, Compu Defrost pad
R-330CW Beverage Center pad, Number selection pads, Kitchen Timer pad
Clock pad, Minute Plus pad, Power Level pad, Stop/Clear pad,
Start Touch On pad
1.1 Cubic Feet
Control Complement
Oven Cavity Light
Safety Standard
Yes
UL Listed
FCC Authorized
DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
GENERAL INFORMATION
GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed
and grounded in accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the
electric current.
WARNING: Improper use of the grounding plug can result in a risk of electric shock.
Electrical Requirements
The electrical requirements are a 120 volt 60 Hz, AC only,
15 or 20 amp. fused electrical supply. It is recommended that a separate circuit serving only this appliance be provided. When
installing this appliance, observe all applicable codes and ordinances.
4
R-320CD/CK/CW
R-330CK/CW
A short power-supply cord is provided to reduce risks of becoming
entangled in or tripping over a longer cord.
Where a two-pronged wall-receptacle is encountered, it is the personal
responsibility and obligation of the customer to contact a qualified
electrician and have it replaced with a properly grounded three-pronged
wall receptacle or have a grounding adapter properly grounded and
polarized. If the extension cord must be used, it should be a 3-wire, 15
amp. or higher rated cord. Do not drape over a countertop or table where
it can be pulled on by children or tripped over accidentally.
CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE ROUND GROUNDING PRONG FROM THIS
PLUG.
3-Pronged Plug
Grounded
Receptacle Box
Grounding Pin
3-Pronged Receptacle
OVEN DIAGRAM
6
9
5
2
10
8
4
11
12
7
3
1
1. One touch door open button.
Push to open door.
2. Door latches.
The oven will not operate unless
the door is securely closed.
3. Removable turntable support.
4. Removable turntable.
The turntable will rotate
clockwise or counterclockwise.
5. Oven lamp.
It will light when oven is
operating or door is opened.
6. Oven door with see-through
window.
7. Ventilation openings. (Rear)
8. Auto-Touch control panel.
9. Time display: Digital display,
99 minutes 99 seconds.
10. Coupling.
11. Wave guide cover.
12. Power supply cord
TOUCH CONTROL PANEL
R-320CD/CK/CW
R-330CK/CW
COOK SENSOR LBS KG DEF HELP
REHEAT SENSOR
SENSOR DEFROST
CUSTOM HELP
SENSOR COOK
Baked
Potatoes
Popcorn
Frozen
Entrees
Frozen
Vegetables
Rice
Fresh
Vegetables
Ground
Meat
Chicken
Breast
Fish/
Seafood
COOK HELP
Popcorn
Sensor
reheat
Custom
help
Fresh
vegetables
Rice
Baked
potatoes
Ground
meat
Poultry
Fish/
seafood
Frozen
entrees
Frozen
snacks
Frozen
vegetables
INSTANT ACTION
Fresh
Rolls/Muffins
Beverage
Frozen
Rolls/Muffins
COMPU DEFROST
Steaks/
Chops
Ground
Meat
Chicken
Pieces
1
2
3
4
5
6
7
8
9
o
Kitchen
Timer
Clock
Minute
Plus
Kitchen
Timer
Clock
Minute
Plus
Power
Level
Stop
Clear
Start
Power
Level
Stop
Clear
Start
Touch On
5
R-320CD/CK/CW
R-330CK/CW
OPERATION
DESCRIPTION OF OPERATING SEQUENCE
7. The monitor switch electrically monitors the operation of
the secondary interlock switch and primary interlock
relay and is mechanically associated with the door so
that it will function in the following sequence.
(1) When the door opens from the closed position, the
primary interlock relay (RY2) and secondary interlock
switch open their contacts. And contacts of the relay
(RY1) remains closed. Then the monitor switch contacts
close.
(2) When the door is closed from the open position, the
monitor switch contacts open first. Then the contacts of
the secondary interlock switch and door sensing switch
close. And contacts of the relay (RY1) open.
If the secondary interlock switch and primary interlock relay
(RY2) fail with the contacts closed when the door is opened,
the closing of the monitor switch contacts will form a short
circuit through the monitor fuse, secondary interlock switch,
relay (RY1) and primary interlock relay (RY2), causing the
monitor fuse to blow.
The following is a description of component functions during
oven operation.
OFF CONDITION
Closing the door activates the door sensing switch and
secondary interlock switch. (In this condition, the monitor
switch contacts are opened.)
When oven is plugged in, 120 volts A.C. is supplied to the
control unit (Figure O-1).
1. The display will show flashing "88:88" (for R-320CD/
CK/CW). The display will show "SHARP SIMPLY
PRESS CLEAR AND PRESS CLOCK" (for R-330CK/
CW).To set any program or set the clock, you must first
touch the STOP/CLEAR pad. The display will clear,
and " : " will appear.
COOKING CONDITION
Program desired cooking time by touching the NUMBER
pads. Program the power level by touching the POWER
LEVEL pad and then a Number pad.
When the START pad is touched, the following operations
occur:
POWER LEVEL P-0 TO P-90 COOKING
When Variable Cooking Power is programmed, the 120
volts A.C. is supplied to the power transformer intermittently
through the contacts of relay (RY-2) which is operated by the
control unit within a 32 second time base. Microwave power
operation is as follows:
1. The contacts of relays are closed and components
connected to the relays are turned on as follows.
(For details, refer to Figure O-2)
RELAY
RY-1
RY-2
VARI-MODE
Power 10(P-HI)
(100% power)
Power 9(P-90)
(approx. 90% power)
Power 8(P-80)
(approx. 80% power)
Power 7(P-70)
(approx. 70% power)
Power 6(P-60)
(approx. 60% power)
Power 5(P-50)
(approx. 50% power)
Power 4(P-40)
(approx. 40% power)
Power 3(P-30)
(approx. 30% power)
Power 2(P-20)
(approx. 20% power)
Power 1(P-10)
(approx. 10% power)
Power 0(P-0)
(0% power)
CONNECTED COMPONENTS
oven lamp/turntable motor/fan motor
power transformer
2. 120 volts A.C. is supplied to the primary winding of the
power transformer and is converted to about 3.2 volts
A.C. output on the filament winding, and approximately
2150 volts A.C. on the high voltage winding.
3. The filament winding voltage heats the magnetron
filament and the H.V. winding voltage is sent to a voltage
doubler circuit.
4. The microwave energy produced by the magnetron is
channelled through the waveguide into the cavity feedbox, and then into the cavity where the food is placed to
be cooked.
5. Upon completion of the cooking time, the power
transformer, oven lamp, etc. are turned off, and the
generation of microwave energy is stopped. The oven
will revert to the OFF condition.
6. When the door is opened during a cook cycle, the
monitor switch, door sensing switch, secondary interlock
switch, relay (RY1) and primary interlock relay are
activated with the following results. The circuits to the
turntable motor, the cooling fan motor, and the high
voltage components are de-energized, the oven lamp
remains on, and the digital read-out displays the time still
remaining in the cook cycle when the door was opened.
Note:
6
ON TIME
32 sec.
OFF TIME
0 sec.
30 sec.
2 sec.
26 sec.
6 sec.
24 sec.
8 sec.
22 sec.
10 sec.
18 sec.
14 sec.
16 sec.
16 sec.
12 sec.
20 sec.
8 sec.
24 sec.
6 sec.
26 sec.
0 sec.
32 sec.
The ON/OFF time ratio does not correspond with
the percentage of microwave power, because
approx. 2 seconds are needed for heating of the
magnetron filament.
R-320CD/CK/CW
R-330CK/CW
SENSOR COOKING CONDITION
NOTE: During this first stage, do not open the door or touch
STOP/CLEAR pad.
4. When the sensor detects the vapor emitted from the
food, the display switches over to the remaining cooking
time and the timer counts down to zero.
At this time, the door may be opened to stir, turn, or
season food.
5. When the timer reaches zero, an audible signal sounds.
The shut-off relay and cook relay are de-energized and
the power transformer, oven lamp, etc. are turned off.
6. Opening the door or touching the STOP/CLEAR pad, the
time of day will reappear on the display and the oven will
revert to an OFF condition.
Using the SENSOR function, the food is cooked without
figuring time, power level or quantity. When the oven senses
enough steam from the food, it relays the information to its
microprocessor which will calculate the remaining cooking
time and power level needed for best results. When the food
is cooked, water vapor is developed. The sensor “senses”
the vapor and its resistance increases gradually. When the
resistance reaches the value set according to the menu,
supplementary cooking is started.
The time of supplementary cooking is determined by experiment with each food category and inputted into the LSI.
An example of how sensor works: (POTATOES)
1. Potates at room temperature. Vapor is emitted very
slowly.
MI
CRO
WA
VE
2. Heat Potates. Moisture and humidity is emitted rapidly.
You can smell the aroma as it cooks.
AH SENSOR
MIC
RO
WA
VE
3. Sensor detects moisture and humidity and calculates
cooking time and variable power.
Cooking Sequence.
1. Touch one of the SENSOR pads (for R-320CD/CK/CW).
Touch one of the SENSOR pads and then touch the Start
pad (for R-330CK/CW).
NOTE: The oven should not be operated on SENSOR
immediately after plugging in the unit. Wait two
minutes before cooking on SENSOR.
2. The coil of shut-off relay (RY-1) is energized, the turntable
motor, oven lamp and cooling fan motor are turned on,
but the power transformer is not turned on.
3. After about 16 seconds, the cook relay (RY-2) is
energized. The power transformer is turned on,
microwave energy is produced and first stage is started.
The 16 seconds is the cooling time required to remove
any vapor from the oven cavity and sensor.
7
R-320CD/CK/CW
R-330CK/CW
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. CLOCK APPEARS ON DISPLAY.
MONITOR
FUSE 20A
NOTE: "
THERMAL
CUT-OUT (OVEN)
" indicates components with potential above 250V.
THERMAL
CUT-OUT (MG.)
COM.
POWER
TRANSFORMER
N.O.
F3
A2
CAPACITOR 1.0µF
AC 2300V
F2
F1
PRIMARY
INTERLOCK
RELAY
AH SENSOR
(RY-2)
(RY-1)
A1
CONTROL UNIT
N.O.
COM.
SH-B
GRN
120V AC
60 Hz
SH-A
DOOR
SENSING
SWITCH
TTM
OL
MONITOR
SWITCH
FM
RECTIFIER
MAGNETRON
TURNTABLE
MOTOR
OVEN
LAMP
FAN
MOTOR
SECONDARY
INTERLOCK
SWITCH
Figure O-1. Oven Schematic-Off Condition
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. COOKING TIME PROGRAMMED.
3. VARIABLE COOKING CONTROL "HIGH".
4. "START" PAD TOUCHED.
MONITOR
FUSE 20A
THERMAL
CUT-OUT (OVEN)
THERMAL
CUT-OUT (MG.)
COM.
POWER
TRANSFORMER
N.O.
CONTROL UNIT
N.O.
COM.
SH-B
GRN
120V AC
60 Hz
SH-A
DOOR
SENSING
SWITCH
TTM
OL
CAPACITOR 1.0µF
AC 2300V
F1
PRIMARY
INTERLOCK
RELAY
F2
(RY-2)
(RY-1)
A1
AH SENSOR
F3
A2
MONITOR
SWITCH
FM
RECTIFIER
MAGNETRON
OVEN
LAMP
TURNTABLE
MOTOR
FAN
MOTOR
SECONDARY
INTERLOCK
SWITCH
Figure O-2. Oven Schematic-Cooking Condition
8
R-320CD/CK/CW
R-330CK/CW
DESCRIPTION AND FUNCTION OF COMPONENTS
DOOR OPEN MECHANISM
of the monitor switch contacts.
CAUTION: BEFORE REPLACING A BLOWN MONITOR
FUSE TEST THE DOOR SENSING SWITCH,
PRIMARY INTERLOCK RELAY (RY2), RELAY
(RY1), SECONDARY INTERLOCK SWITCH
AND MONITOR SWITCH FOR PROPER OPERATION. (REFER TO CHAPTER "TEST PROCEDURE").
NOTE: MONITOR FUSE AND MONITOR SWITCH ARE
REPLACED AS AN ASSEMBLY.
The door is opened by pushing the open button on the
control panel, refer to the Figure D-1.
When the open button is pushed, the open button pushes up
the switch lever, and then the switch lever pushes up the
latch head. The latch heads are moved upward and released from latch hook. Now the door will open.
Door
Latch Hook
Latch
Heads
Door Sensing
Switch
TURNTABLE MOTOR
The turntable motor rotates the turntable located on the
bottom of the oven cavity, so that the foods on the turntable
cook evenly during cooking. The turntable may turn in either
direction.
Monitor Switch
Switch Lever
COOLING FAN MOTOR
Secondary
Interlock Switch
The cooling fan motor drives a blade which draws external
cool air. This cool air is directed through the air vanes
surrounding the magnetron and cools the magnetron. This
air is channelled through the oven cavity to remove steam
and vapors given off from the heating foods. It is then
exhausted through the exhausting air vents at the oven
cavity.
Figure D-1. Door Open Mechanism
DOOR SENSING AND SECONDARY INTERLOCK
SWITCHES
The secondary interlock switch is mounted in the lower
position of the latch hook and the door sensing switch in the
primary interlock system is mounted in the upper position of
the latch hook. They are activated by the latch heads on the
door. When the door is opened, the switches interrupt the
power to all high voltage components. A cook cycle cannot
take place until the door is firmly closed thereby activating
both interlock switches. The primary interlock system consists of the door sensing switch and primary interlock relay
located on the control circuit board.
MONITOR FUSE
1. The monitor fuse blows when the contacts (COM-NO) of
the primary interlock relay (RY2) and secondary interlock
switch remain closed with the oven door open and when
the monitor switch closes.
2. If the wire harness or electrical components are shortcircuited, this monitor fuse blows to prevent an electric
shock or fire hazard.
MONITOR SWITCH
OVEN THERMAL CUT-OUT
The monitor switch is activated (the contacts opened) by the
latch head on the door while the door is closed. The switch
is intended to render the oven inoperative, by means of
blowing the monitor fuse, when the contacts of the primary
interlock relay (RY2) and secondary interlock switch fail to
open when the door is opened.
The thermal cut-out, located on the top of the oven cavity, is
designed to prevent damage to the oven by fire. If the food
load is overcooked, by either error in cook time or defect in
the control unit, the thermal cut-out will open.
Under normal operation, the oven thermal cut-out remains
closed. However, when abnormally high temperatures are
reached within the oven cavity, the oven thermal cut-out will
open at 257˚F(125˚C), causing the oven to shut down.
Functions:
1. When the door is opened, the monitor switch contact
close (to the ON condition) due to their being normally
closed. At this time the primary interlock relay (RY2) and
secondary interlock switch are in the OFF condition
(contacts open) due to their being normally open contact
switches.
2. As the door goes to a closed position, the monitor switch
contacts are first opened and then the door sensing
switch and the secondary interlock switch contacts close.
(On opening the door, each of these switches operate
inversely.)
3. If the door is opened, and the primary interlock relay
(RY2) and secondary interlock switch contacts fail to
open, the monitor fuse blows simultaneously with closing
MAGNETRON THERMAL CUT-OUT
The thermal cut-out located near the magnetron is designed
to prevent damage to the magnetron if an over heated
condition develops in the tube due to cooling fan failure,
obstructed air guide, dirty or blocked air intake, etc.
Under normal operation, the thermal cut-out remains closed.
However, when abnormally high temperatures are reached
within the magnetron, the thermal cut-out will open at
293˚F(145˚C) causing the oven to shut down.
9
R-320CD/CK/CW
R-330CK/CW
TROUBLESHOOTING GUIDE
Never touch any part in the circuit with your hand or an uninsulated tool while the power supply is connected.
When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many
of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter which
will be found in the "Test Procedure "section.
IMPORTANT: If the oven becomes inoperative because of a blown monitor fuse, check the monitor switch, relay (RY1)
primary interlock relay (RY2), door sensing switch and secondary interlock switch before replacing the
monitor fuse. If the monitor fuse is replaced, the monitor switch must also be replaced. Use part FFSBA023WRK0 as an assembly.
IMPORTANT: Whenever troubleshooting is performed with the power supply cord disconnected. It may in, some cases,
be necessary to connect the power supply cord after the outer case has been removed, in this event,
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
When the testing is completed
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is installed.
7. Run the oven and check all functions.
10
R-320CD/CK/CW
R-330CK/CW
CK = Check / RE = Replace
Home fuse or circuit breaker blows
when power cord is plugged into wall
receptacle
Monitor fuse blows when power cord
is plugged into wall receptacle.
OFF
CONDITION
All letters and indicators do not appear in display when power cord is
first plugged into wall outlet.
Display does not operate properly
when STOP/CLEAR key is touched.
(Buzzer should sound and ":" or time
of day should appear in display.)
Oven lamp does not light when door
is opened.
Oven lamp does not go out when
door is closed.
Oven lamp lights but fan motor and
turntable motor do not operate.
Oven does not go into cook cycle
when START pad is touched
Oven seems to be operating but little
or no heat is produced in oven load.
(Food incompletely cooked or not
cooked at all at end of cook cycle.)
COOKING
CONDITION
Oven goes into a cook cycle but
extremely uneven heating is produced in oven load (food).
Oven does not cook properly when
programmed for Cooking Power 5
mode. (Operates properly on Cooking Power 10 (HIGH) mode.)
Oven goes into COMPU DEFROST
but food is not defrosted well.
SENSOR
COOKING
CONDITION
AH sensor does not end during Sensor cooking condition. (Oven does
not shut off after a cup of water is
boiling by sensor cooking.)
Oven stops at 16 sec. after starting.
11
AH SENSOR
FOIL PATTERN ON PWB.
COMPU DEFROST
RELAY (RY1)
KEY UNIT
DIRTY OVEN CAVITY
LOW VOLTAGE
WRONG OPERATION
TOUCH CONTROL PANEL
TURNTABLE MOTOR
COOLING FAN MOTOR
OVEN LAMP OR SOCKET
MONITOR FUSE
MONITOR SWITCH
SECONDARY INTERLOCK SWITCH
PRIMARY INTERLOCK SYSTEM
THERMAL CUT-OUT
HIGH VOLTAGE CAPACITOR
H.V. RECTIFIER ASSEMBLY
POWER TRANSFORMER
MAGNETRON
PROBLEM
SHORT OR OPENED WIRING
CONDITION
RE RE A B C D E F F G H RE RE CK I CK CK CK J K L M N
SHORT IN POWER CORD
POSSIBLE CAUSE
AND
DEFECTIVE PARTS
TEST PROCEDURE
R-320CD/CK/CW
R-330CK/CW
TEST PROCEDURES
PROCEDURE
LETTER
A
COMPONENT TEST
MAGNETRON ASSEMBLY TEST
1.
2.
3.
4.
5.
6.
7.
8.
9.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
To test for an open filament, isolate the magnetron from the high voltage circuit. A continuity check
across the magnetron filament leads should indicate less than 1 ohm.
To test for a shorted magnetron, connect the ohmmeter leads between the magnetron filament leads
and chassis ground. This test should indicate an infinite resistance. If there is little or no resistance
the magnetron is grounded and must be replaced.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
MICROWAVE OUTPUT POWER
The following test procedure should be carried out with the microwave oven in a fully assembled
condition (outer case fitted).
HIGH VOLTAGES ARE PRESENT DURING THE COOK CYCLE, SO EXTREME CAUTION SHOULD
BE OBSERVED.
Power output of the magnetron can be measured by performing a water temperature rise test. This test
should only be used if above tests do not indicate a faulty magnetron and there is no defect in the following
components or wiring: silicon rectifier, high voltage capacitor and power transformer. This test will require
a 16 ounce (453cc) measuring cup and an accurate mercury thermometer or thermocouple type
temperature tester. For accurate results, the following procedure must be followed carefully:
1. Fill the measuring cup with 16 oz. (453cc) of tap water and measure the temperature of the water with
a thermometer or thermocouple temperature tester. Stir the thermometer or thermocouple through
the water until the temperature stabilizes. Record the temperature of the water.
2. Place the cup of water in the oven. Operate oven at POWER 10(HIGH) selecting more than 60
seconds cook time. Allow the water to heat for 60 seconds, measuring with a stop watch, second hand
of a watch or the digital read-out countdown.
3. Remove the cup from the oven and again measure the temperature, making sure to stir the
thermometer or thermocouple through the water until the maximum temperature is recorded.
4. Subtract the cold water temperature from the hot water temperature. The normal result should be 32.6
to 60.6˚F(18.1 to 33.7˚C) rise in temperature. If the water temperatures are accurately measured and
tested for the required time period the test results will indicate if the magnetron tube has low power
output (low rise in water temperature) which would extend cooking time or high power output (high
rise in water temperature) which would reduce cooking time. Because cooking time can be adjusted
to compensate for power output, the magnetron tube assembly should be replaced only if the water
temperature rise test indicates a power output well beyond the normal limits. The test is only accurate
if the power supply line voltage is 120 volts and the oven cavity is clean.
B
POWER TRANSFORMER TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the primary input terminals and measure the resistance of the transformer with an
ohmmeter. Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance of
the primary coil should be less than 1 ohm and the resistance of the high voltage coil should be
approximately 86.3 ohms; the resistance of the filament coil should be less than 1 ohm.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
12
R-320CD/CK/CW
R-330CK/CW
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
(HIGH VOLTAGES ARE PRESENT AT THE HIGH VOLTAGE TERMINAL, SO DO NOT ATTEMPT TO
MEASURE THE FILAMENT AND HIGH VOLTAGE.)
C
HIGH VOLTAGE RECTIFIER TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Isolate the rectifier from the circuit. Using the highest ohm scale of the meter, read the resistance
across the terminals and observe, reverse the leads to the rectifier terminals and observe meter
reading. If a short is indicated in both directions, or if an infinite resistance is read in both directions,
the rectifier is probably defective and should be replaced.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: Be sure to use an ohmmeter that will supply a forward bias voltage of more than 6.3 volts.
D
HIGH VOLTAGE CAPACITOR TEST
1.
2.
3.
4.
5.
6.
7.
8.
E
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the capacitor is open, no high voltage will be available to the magnetron. Disconnect input leads
and check for short or open between the terminals using an ohmmeter.
Checking with a high ohm scale, if the high voltage capacitor is normal, the meter will indicate
continuity for a short time and should indicate an open circuit once the capacitor is charged. If the
above is not the case, check the capacitor with an ohmmeter to see if it is shorted between either of
the terminals and case. If it is shorted, replace the capacitor.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
OVEN THERMAL CUT-OUT TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
A continuity check across the thermal cut-out terminals should indicate a closed circuit unless the
temperature of the thermal cut-out reaches approximately 257˚F(125˚C).
An open thermal cut-out indicates overheating of the oven, exchange the oven thermal cut-out and
check inside of oven cavity and for improper setting of cooking time or operation of control unit. Check
for restricted air flow through the vent holes of the oven cavity, especially the cooling fan and air guide.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
MAGNETRON THERMAL CUT-OUT TEST
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. A continuity check across the thermal cut-out terminals should indicate a closed circuit unless the
temperature of the magnetron reaches approximately 293˚F(145˚C). An open thermal cut-out
indicates overheating of the magnetron. Check for restricted air flow to the magnetron, especially the
cooling fan air guide.
13
R-320CD/CK/CW
R-330CK/CW
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
CAUTION: IF THE THERMAL CUT-OUT INDICATES AN OPEN CIRCUIT AT ROOM TEMPERATURE,
REPLACE THERMAL CUT-OUT.
F
SECONDARY INTERLOCK SWITCH TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the secondary interlock switch.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
PRIMARY INTERLOCK SYSTEM TEST
DOOR SENSING SWITCH
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the door sensing switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: If the door sensing switch contacts fail in the open position and the door is closed, the cooling
fan, turntable and oven light will be activated by RY1.
PRIMARY INTERLOCK RELAY (RY2)
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect two (2) wire leads from the male tab terminals of the Primary Interlock Relay. Check the
state of the relay contacts using a ohmmeter. The relay contacts should be open. If the relay contacts
are closed, replace the circuit board entirely or the relay itself.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
G
MONITOR SWITCH TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Before performing this test, make sure that the secondary interlock switch and the primary interlock
relay are operating properly, according to the above Switch Test Procedure. Disconnect the wire lead
from the monitor switch (COM) terminal. Check the monitor switch operation by using the ohmmeter
as follows. When the door is open, the meter should indicate a closed circuit. When the monitor switch
actuator is pushed by a screw driver through the lower latch hole on the front plate of the oven cavity
14
R-320CD/CK/CW
R-330CK/CW
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
5.
6.
7.
8.
with the door opened (in this condition the plunger of the monitor switch is pushed in), the meter should
indicate an open circuit. If improper operation is indicated, the switch may be defective. After testing
the monitor switch, reconnect the wire lead to the monitor switch (COM) terminal and check the
continuity of the monitor circuit.
Screw Driver
Reconnect all leads removed from
RED
WHT
components during testing.
Monitor
Reinstall the outer case (cabinet).
Switch
Reconnect the power supply cord after
the outer case is installed.
Run the oven and check all functions.
Secondary
Interlock Switch
H
Ohmmeter
BLOWN MONITOR FUSE TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the monitor fuse is blown when the door is opened, check the primary interlock relay, secondary
interlock switch and monitor switch according to the "TEST PROCEDURE" for those switches before
replacing the blown monitor fuse.
CAUTION: BEFORE REPLACING A BLOWN MONITOR FUSE, TEST THE PRIMARY INTERLOCK
RELAY, SECONDARY INTERLOCK SWITCH, DOOR SENSING SWITCH AND MONITOR
SWITCH FOR PROPER OPERATION.
If the monitor fuse is blown by improper switch operation, the monitor fuse and monitor switch must
be replaced with "monitor fuse and monitor switch assembly" part number FFS-BA023WRK0, even
if the monitor switch operates normally. The monitor fuse and monitor switch assembly is comprised
of a 20 ampere fuse and switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
I
TOUCH CONTROL PANEL ASSEMBLY TEST
The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore,
unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter
and ohmmeter.
In this service manual, the touch control panel assembly is divided into two units, Control Unit and Key
Unit, and also the Control Unit is divided into two units, CPU Unit and Power Unit, and troubleshooting
by unit replacement is described according to the symptoms indicated.
Before testing,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
6) After that procedure, re-connect the power supply cord.
1. Key Unit.
NOTE ;
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Check Key unit ribbon connection before replacement.
5) Reconnect all leads removed from components during testing.
15
R-320CD/CK/CW
R-330CK/CW
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
6) Re-install the outer case (cabinet).
7) Reconnect the power supply cord after the outer case is installed.
8) Run the oven and check all functions.
The following symptoms indicate a defective key unit.
a) When touching the pads, a certain pad produces no signal at all.
b) When touching a number pad, two figures or more are displayed.
c) When touching the pads, sometimes a pad produces no signal.
If the Key unit is defective.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Replace the Key unit.
5) Reconnect all leads removed from components during testing.
6) Re-install the outer case (cabinet).
7) Reconnect the power supply cord after the outer case is installed.
8) Run the oven and check all functions.
2. Control Unit
The following symptoms indicate a defective control unit. Before replacing the control unit, perform
the Key unit test (Procedure J) to determine if control unit is faulty.
2-1 In connection with pads.
a) When touching the pads, a certain group of pads do not produce a signal.
b) When touching the pads, no pads produce a signal.
2-2 In connection with indicators
a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
f) A certain group of indicators do not light up.
g) The figure of all digits flicker.
2-3 Other possible problems caused by defective control unit.
a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.
When testing is completed,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Reconnect all leads removed from components during testing.
5) Re-install the outer case (cabinet).
6) Reconnect the power supply cord after the outer case is installed.
7) Run the oven and check all functions.
J
KEY UNIT TEST
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable
is making good contact, verify that the door sensing switch (stop switch) operates properly; that is the
contacts are closed when the door is closed and open when the door is open. If the door sensing
switch (stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control
unit and make sure the door sensing switch is closed (either close the door or short the door sensing
switch connecter). Use the Key unit matrix indicated on the control panel schematic and place a
jumper wire between the pins that correspond to the STOP/CLEAR pad making momentary contact.
If the control unit responds by clearing with a beep the key unit is faulty and must be replaced. If the
16
R-320CD/CK/CW
R-330CK/CW
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
control unit does not respond, it is faulty and must be replaced. If a specific pad does not respond,
the above method may be used (after clearing the control unit) to determine if the control unit or key
pad is at fault.
5. Reconnect all leads removed from components during testing.
6. Re-install the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
G7
G8
G6
G5
G2
G7
G8
G1
G6
G4
G3
G9
5
4
3
G4
G3
2
1
Beverage
center
7
6
Compu
Defrost
G9
5
4
3
2
1
G10
0
9
8
7
6
Steaks/
Baked
Chops Popcorn Potatoes
G10
0
9
8
G11
Minute
Plus
Chicken
Breast
Clock
Kitchen
Timer
Start
Rice
Frozen
vegetables
G11
Minute
Plus
Frozen
snacks
Clock
G12
Frozen
Rolls/
Muffins
Stop
Clear
Beverage
Power
Level
Fresh
Rolls/
Muffins
Fresh
Fish/
Ground Meat
vegetables Seafood (SENSOR COOK)
G12
One Dish
Dinners
Stop
Clear
G13
Ground Meat
(COMPU DEFROST)
G13
Popcorn
Sensor Baked Custom
reheat Potatoes Help
CUSTOM Frozen REHEAT
Entrees SENSOR
HELP
Start
Kitchen
Timer Touch On
G2
G1
Rice
Fresh
vegetables
Poultry
Ground
meat
Frozen
Lunch on Power Breakfast Fish/
seafood vegetables
Bar
the Run Level
Frozen
entrees
Super
Defrost
G14
G14
R-320CD/CK/CW
K
G5
Chicken
Pieces
R-330CK/CW
RELAY TEST
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that these leads remain isolated from other components and oven chassis by using insulation
tape.
6. After that procedure, re-connect the power supply cord.
7. Remove the outer case and check voltage between Pin No. 1 of the 2 pin connector (A) and the
common terminal of the relay RY1 on the control unit with an A.C. voltmeter.
The meter should indicate 120 volts, if not check oven circuit.
RY1 and RY2 Relay Test
These relays are operated by D.C. voltage
Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation.
DC. voltage indicated ............... Defective relay.
DC. voltage not indicated ......... Check diode which is connected to the relay coil. If diode is good,
control unit is defective.
RELAY SYMBOL
OPERATIONAL VOLTAGE
RY1
Approx. 24.0V D.C.
Oven lamp / Turntable motor / Cooling fan motor
CONNECTED COMPONENTS
RY2
Approx. 23.0V D.C.
Power transformer
8. Disconnect the power supply cord, and then remove outer case.
9. Open the door and block it open.
10.Discharge high voltage capacitor.
11.Reconnect all leads removed from components during testing.
12.Re-install the outer case (cabinet).
13.Reconnect the power supply cord after the outer case is installed.
14.Run the oven and check all functions.
L
COMPU DEFROST TEST
WARNING : The oven should be fully assembled before following procedure.
(1) Place one cup of water in the center of the turntable tray in the oven cavity.
(2) For R-320CD/CK/CW, Close the door, touch the " Steaks / chops " pad once.
For R-330CK/CW, Close the door, touch the Compu Defrost pad three times and touch the number
pad 5. And then touch the start pad.
17
R-320CD/CK/CW
R-330CK/CW
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
(3) The oven is in Compu Defrost cooking condition.
(4) The oven will operate as follows
WEIGHT
0.5lb
1ST STAGE
LEVEL
TIME
60%
42sec.
2ND STAGE
LEVEL
TIME
40%
32sec.
(5) If improper operation is indicated, the control unit is probably defective and should be checked.
M
FOIL PATTERN ON THE PRINTED WIRING BOARD TEST
To protect the electronic circuits, this model is provided with a fine foil pattern added to the primary
on the PWB, this foil pattern acts as a fuse.
1. Foil pattern check and repairs.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Follow the troubleshooting guide given below for repair.
STEPS
1
2
OCCURRENCE
CAUSE OR CORRECTION
Only pattern at "a" is broken.
Pattern at "a" and "b" are broken.
VRS1
T1
AC
1
VH
2
CN - A
d
a
b
XA
(J1)
c
OMIF
D U
QKITPB026MRE0
5) Make a visual inspection of the varistor.
Check for burned damage and examine the transformer with a tester for the
presence of layer short-circuit (check
the primary coil resistance which is
approximately 212Ω ± 10%). If any
abnormal condition is detected, replace
the defective parts.
*Insert jumper wire J1 and solder.
*Insert the coil RCILF2003YAZZ between "c" and "d".
6) Reconnect all leads removed from components during testing.
7) Re-install the outer case (cabinet).
8) Reconnect the power supply cord after the outer case is installed.
9) Run the oven and check all functions.
2. Follow the troubleshooting guide given below, if indicator does not light up after above check and
repairs are finished.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
6) After that procedure, re-connect the power supply cord.
7) Follow the troubleshooting guide given below for repair.
STEPS
OCCURRENCE
CAUSE OR CORRECTION
1
The rated AC voltage is not present between
Pin No. 1 of the 2-pin connector (A) and the
common terminal of the relay RY1.
Check supply voltage and oven power cord.
2
The rated AC voltage is present at primary
side of low voltage transformer.
Low voltage transformer or secondary circuit defective.
Check and repair.
8) Disconnect the power supply cord, and then remove outer case.
9) Open the door and block it open.
18
R-320CD/CK/CW
R-330CK/CW
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
10) Discharge high voltage capacitor.
11) Reconnect all leads removed from components during testing.
12) Re-install the outer case (cabinet).
13) Reconnect the power supply cord after the outer case is installed.
14) Run the oven and check all functions.
N
AH SENSOR TEST
Checking the initial sensor cooking condition
WARNING : The oven should be fully assembled before following procedure.
(1) The oven should be plugged in at least two minutes before sensor cooking.
(2) Room temperature should not exceed 95˚F (35˚C).
(3) The unit should not be installed in any area where heat and steam are generated. The unit should
not be installed, for example, next to a conventional surface unit. Refer to the “INSTALLATION
INSTRUCTIONS” of the operation manual.
(4) Exhaust vents are provided on the back of the unit for proper cooling and air flow in the cavity. To
permit adequate ventilation, be sure to install so as not to block these vents. There should be some
space for air circulation.
(5) Be sure the exterior of the cooking container and the interior of the oven are dry. Wipe off any moisture
with a dry cloth or paper towel.
(6) The Sensor works with food at normal storage temperature. For example, chicken pieces would be
at refrigerator temperature and canned soup at room temperature.
(7) Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. The
sensor will detect the vapor given of by the spray and turn off before food is properly cooked.
(8) If the sensor has not detected the vapor of the food, ERROR will appear and the oven will shut off.
Water load cooking test
WARNING : The oven should be fully assembled before following procedure.
Make sure the oven has been plugged in at least two minutes before checking sensor cook operation.
The cabinet should be installed and screws tightened.
(1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
(2) Place the container on the center of tray in the oven cavity.
(3) Close the door.
(4) For R-320CD/CK/CW, touch REHEAT SENSOR pad once. Now, the oven is in the sensor cooking
condition and “REHEAT” will appear in the display.
For R-330CK/CW, touch Sensor Reheat pad once and touch the start pad. Now, the oven is in the
sensor cooking condition and "SENSOR REHEAT" will appear in the display.
(5) The oven will operate for the first 16 seconds, without generating microwave energy.
NOTE: ERROR will appear if the door is opened or STOP/CLEAR pad is touched during first stage of
sensor cooking.
(6) After approximately 16 seconds, microwave energy is produced, and the display should start to count
down the remaining cooking time and oven should turn off after water is boiling (bubbling).
If the oven does not turn off, replace the AH sensor or check the control unit, refer to explanation below.
TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT
To determine if the sensor is defective, the simplest method is to replace it with a new replacement
sensor.
(1) Disconnect the power supply cord, and then remove outer case.
(2) Open the door and block it open.
(3) Discharge high voltage capacitor.
(4) Remove the AH sensor.
(5) Install the new AH sensor.
(6) Reconnect all leads removed from components during testing.
(7) Re-install the outer case (cabinet).
(8) Reconnect the power supply cord after the outer case is installed.
(9) Reconnect the oven to the power supply and check the sensor cook operation as follows:
19
R-320CD/CK/CW
R-330CK/CW
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
9-1. Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
9-2. Place the container on the center of tray in the oven cavity.
9-3. Close the door.
9-4. For R-320CD/CK/CW, touch REHEAT SENSOR pad once.
For R-330CK/CW, touch Sensor Reheat pad and touch the Start pad.
9-5. The control panel is in automatic Sensor operation.
9-6. The display will start to count down the remaining cooking time, and the oven will turn off
automatically after the water is boiling (bubbling).
If new sensor dose not operate properly, the problem is with the control unit, and refer to explanation
below.
CHECKING CONTROL UNIT
(1) Disconnect the power supply cord, and then remove outer case.
(2) Open the door and block it open.
(3) Discharge high voltage capacitor.
(4) Disconnect the sensor connector that is mounted to control panel.
(5) Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel.
(6) Disconnect the leads to the primary of the power transformer.
(7) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
(8) After that procedure, re-connect the power supply cord.
(9) Check the sensor cook operation proceed as follows:
9-1. For R-320CD/CK/CW, touch REHEAT SENSOR pad once.
For R-330CK/CW, touch Sensor Reheat pad and touch
the Start pad.
9-2. The control panel is in the sensor cooking operation.
9-3. After approximately 20 seconds, push plunger of select switch for more than 3 seconds. This
condition is same as judgement by AH sensor.
9-4. After approximately 3 seconds, the display shows “ X X . X X “ which is the remaining cooking
time, and the display count down.
If the above is not the case, the control unit is probably defective.
If the above is proper, the AH sensor is probably defective.
(10) Disconnect the power supply cord, and then remove outer case.
(11) Open the door and block it open.
(12) Discharge high voltage capacitor.
(13) Disconnect the dummy resistor circuit from the sensor connector of control panel.
(14) Carry out necessary repair.
(15) Reconnect all leads removed from components during testing and repairing.
(16) Re-install the outer case (cabinet).
(17) Reconnect the power supply cord after the outer case is installed. Run the oven and check all
functions.
(18) Carry out "Water load cooking test" again and ensure that the oven works properly.
F-1
F-2
To connector (F)
on Control Unit.
1
2
3
Plunger
R1, R2 : 22Ω ± 1% 1/2W
R3 : 4.3kΩ ± 5% 1/4W
R4 : 1MΩ ± 5% 1/4W
NC
NO
COM
COM NO
R1
F-3
R2
CONNECTOR
R3
R4
Sensor Dummy Resistor Circuit
20
NC
R-320CD/CK/CW
R-330CK/CW
TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL
7) Door Sensing Switch
A switch to “tell” the LSI if the door is open or closed.
The touch control section consists of the following units.
(1) Key Unit
(2) Control Unit (The Control Unit consists of Power Unit and
LSI Unit).
8) Back Light Circuit
For R-320CD/CK/CW
A circuit to drive the back light (Light emitting diodes LD1LD4).
For R-330CK/CW
A circuit to drive the back light (Light emitting diodes LD10LD19).
The principal functions of these units and the signals communicated among them are explained below.
Key Unit
The key unit is composed of a matrix, signals generated in the
LSI are sent to the key unit through P10-P17.
When a key pad is touched, a signal is completed through the
key unit and passed back to the LSI through AN11, AN10, AN9,
P42, P41 and AN8 to perform the function that was requested.
9) Absolute Humidity Sensor Circuit
This circuit detects moisture of the cooking food to allow its
automatic cooking.
10)Memory IC(IC4)
For R-330CK/CW only
This is a memory IC to adjust the contrast of LCD.
Control Unit
Control unit consists of LSI, ACL circuit, indicator circuit, power
source circuit, relay circuit, buzzer circuit, synchronizing signal
circuit, absolute humidity sensor circuit and back light circuit.
1) ACL
This circuit generates a signal which resets the LSI to the
initial state when power is supplied.
2) Indicator Circuit
For R-320CD/CK/CW
This circuit consists of 36 segments and 3 common electrodes using a Liquid Crystal Display.
For R-330CK/CW
This circuit consists of 40 segments and 16 common
electrodes using a Liquid Crystal Display.
The Liquid Crystal Display (LCD) is drived by LCD driver
IC3.
3) Power Source Circuit
This circuit generates voltages necessary in the control unit
from the AC line voltage.
In addition, the synchronizing signal is available in order to
compose a basic standard time in the clock circuit.
Symbol
Voltage
VC
-5V
Application
LSI(IC1)
4) Relay Circuit
A circuit to drive the magnetron, fan motor, turntable motor
and light the oven lamp.
5) Buzzer Circuit
The buzzer is responsive to signals from the LSI to emit
audible sounds (key touch sound and completion sound).
6) Synchronizing Signal Circuit
The power source synchronizing signal is available in order
to compose a basic standard time in the clock circuit.
It accompanies a very small error because it works on
commercial frequency.
21
R-320CD/CK/CW
R-330CK/CW
LSI(IZA949DR) : R-320CD/CK/CW
The I/O signal of the LSI(IZA949DR) is detailed in the following table.
Pin No.
Signal
I/O
Description
1
AN10
IN
Signal coming from touch key.
When either G10 line on key matrix is touched, a corresponding signal out of P10 - P17 will
be input into AN10. When no key is touched, the signal is held at "H" level.
2
AN11
IN
Signal similar to AN10.
When either G9 line on key matrix is touched, a corresponding signal will be input into AN11.
3
AVSS
IN
Connected to VC.
4
P10
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G8 line keys on key matrix is touched.
5
P11
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G7 line keys on key matrix is touched.
6
P12
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G6 line keys on key matrix is touched.
7
P13
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G5 line keys on key matrix is touched.
8
P14
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G4 line keys on key matrix is touched.
9
P15
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G3 line keys on key matrix is touched.
10
P16
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G2 line keys on key matrix is touched.
11
P17
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN8, AN9, AN10, AN11, P41
and P42 terminal while one of G1 line keys on key matrix is touched.
12
X1
IN
Connected to GND.
13
X2
OUT
Terminal not used.
14
VSS
IN
15
OSC2
OUT
16
OSC1
IN
Internal clock oscillation frequency control output.
Output to control oscillation input of OSC2.
Internal clock oscillation frequency input setting.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit with
respect to OSC1 terminal.
17
TEST
IN
Connected to VC.
18
RES
IN
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily set "L"
level the moment power is applied, at this time the LSI is reset. Thereafter set at "H" level.
19
P20
OUT
Power source voltage: -5.0V.
VC voltage of power source circuit input.
Signal to sound buzzer (2.0 kHz).
A: key touch sound.
B: Completion sound.
0.1 sec.
H : GND
A
2.0 sec.
L : -5V
H : GND
B
L : -5V
20-22
P21-P23
OUT
Terminal not used.
22
R-320CD/CK/CW
R-330CK/CW
Pin No.
Signal
I/O
23
P24
OUT
Description
Oven lamp, fan motor and turntable motor driving signal
16.7 msec.
To turn on and off shut off relay (RY1). The
square waveform voltage is delivered to the
RY1 driving circuit and RY2 control circuit.
H : GND
L : -5V
During cooking
24
P25
OUT
Magnetron high-voltage circuit driving signal.
OFF
H : GND
To turn on and off the cook relay (RY2). The
signals holds "L" level during microwave cookP-HI
ON
L : -5V
ing and "H" level while not cooking. In other
OFF
OFF
H : GND
cooking modes (variable cooking) the signal
24 sec.
P-70
turns to "H" level and "L" level in repetition
8 sec.
ON
L : -5V
according to the power level.
(ON and OFF times for other power level.)
25-26
P26-P27
OUT
Terminal not used.
27-29
P30-P32
OUT
Terminal not used.
30-34
P33-P37
OUT
Used for initial balancing of the bridge circuit (absolute humidity sensor).
35
CVCC
IN
Connected to GND.
36
VSS
IN
Power source voltage: -5.0V.
The power source voltage to the LSI is input to VSS terminal. Connected to VC.
37-38
V3-V2
IN
Power source voltage input terminal.
Standard voltage for LCD.
39-40
V1-V0
IN
Power source voltage input terminal.
Standard voltage for LCD. Connected to GND.
41
VCC
IN
Power source voltage: GND (0V).
The power source voltage to drive the LSI is input to VCC terminal.
42
COM4
OUT
Terminal not used.
43
COM3
OUT
Common data signal: COM2.
Connected to LCD signal COM2.
44
COM2
OUT
Common data signal: COM1.
Connected to LCD signal COM1.
45
COM1
OUT
Common data signal: COM0.
Connected to LCD signal COM0.
46-54
SEG1-SEG9
OUT
Segment data signal.
Connected to LCD.
The relation between signals are as follows:
LSI signal (Pin No.)
LCD (Pin No.)
SEG 1 (46) ................................ SEG 0
SEG 2 (47) ................................ SEG 1
SEG 3 (48) ................................ SEG 2
SEG 4 (49) ................................ SEG 3
SEG 5 (50) ................................ SEG 4
SEG 6 (51) ................................ SEG 5
SEG 7 (52) ................................ SEG 6
SEG 8 (53) ................................ SEG 7
SEG 9 (54) ................................ SEG 8
SEG 11 (56) ................................ SEG 9
SEG 12 (57) ............................... SEG 10
SEG 13 (58) ............................... SEG 11
SEG 14 (59) ............................... SEG 12
SEG 15 (60) ............................... SEG 13
SEG 16 (61) ............................... SEG 14
SEG 17 (62) ............................... SEG 15
SEG 18 (63) ............................... SEG 16
SEG 19 (64) ............................... SEG 17
23
LSI signal (Pin No.)
LCD (Pin No.)
SEG 20 (65) .............................. SEG 18
SEG 21 (66) .............................. SEG 19
SEG 22 (67) .............................. SEG 20
SEG 23 (68) .............................. SEG 21
SEG 24 (69) .............................. SEG 22
SEG 25 (70) .............................. SEG 23
SEG 26 (71) .............................. SEG 24
SEG 27 (72) .............................. SEG 25
SEG 28 (73) .............................. SEG 26
SEG 29 (74) .............................. SEG 27
SEG 30 (75) .............................. SEG 28
SEG 31 (76) .............................. SEG 29
SEG 32 (77) .............................. SEG 30
SEG 33 (78) .............................. SEG 31
SEG 34 (79) .............................. SEG 32
SEG 35 (80) .............................. SEG 33
SEG 36 (81) .............................. SEG 34
SEG 37 (82) .............................. SEG 35
R-320CD/CK/CW
R-330CK/CW
Pin No.
Signal
I/O
55
SEG10
OUT
Terminal not used.
Description
56-82
SEG11-SEG37
OUT
Segment data signal.
Signal similar to SEG1.
83-85
SEG38-SEG40
OUT
Terminal not used.
86
P40
OUT
Terminal not used.
87
P41
IN
Signal similar to AN10.
When either G13 line on key matrix is touched, a corresponding signal will be input into P41.
88
P42
IN
Signal similar to AN10.
When either G12 line on key matrix is touched, a corresponding signal will be input into P42.
89
IRQ0
IN
Signal synchronized with commercial power source frequency.
This is the basic timing for time processing of LSI.
H : GND
L : -5V
16.7 msec.
90
AVCC
IN
A/D converter power source voltage.
The power source voltage to drive the A/D converter in the LSI. Connected to GND.
91
AN0
IN
Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is an
analog input terminal from the AH sensor circuit, and connected to the A/D converter built
into the LSI.
92
AN1
IN
AH sensor input.
This input is an analog input terminal from the AH sensor circuit, and connected to the A/
D converter built into the LSI.
93
AN2
IN
To input signal which communicates the door open/close information to LSI.
Door close "H" level signal (0V). Door open "L" level signal (-5V).
94
AN3
OUT
95-98
AN4-AN7
IN
Terminal to change cooking input according to the Model.
By using the A/D converter contained in the LSI, DC voltage in accordance with the Model
in operation is applied to set up its cooking constant.
99
AN8
IN
Input terminal to judge the model.
The signal out of P17 will be input into AN8 through G1 line on key matrix. The LSI will judge
the model by this signal.
100
AN9
IN
Signal similar to AN10.
When either G11 line on key matrix is touched, a corresponding signal will be input into AN9.
Terminal not used.
LSI(IZA950DR) : R-330CK/CW
The I/O signal of the LSI(IZA950DR) is detailed in the following table.
Pin No.
Signal
I/O
Description
1
AN10
IN
Signal coming from touch key.
When either G10 line on key matrix is touched, a corresponding signal out of P10 - P17 will
be input into AN10. When no key is touched, the signal is held at "H" level.
2
AN11
IN
Signal similar to AN10.
When either G9 line on key matrix is touched, a corresponding signal will be input into AN11.
3
AVSS
IN
Connected to VC.
4
P10
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G8 line keys on key matrix is touched.
5
P11
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G7 line keys on key matrix is touched.
6
P12
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
24
R-320CD/CK/CW
R-330CK/CW
Pin No.
Signal
I/O
Description
P42 terminal while one of G6 line keys on key matrix is touched.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G5 line keys on key matrix is touched.
7
P13
OUT
8
P14
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G4 line keys on key matrix is touched.
9
P15
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G3 line keys on key matrix is touched.
10
P16
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G2 line keys on key matrix is touched.
11
P17
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN8, AN9, AN10, AN11, P41
and P42 terminal while one of G1 line keys on key matrix is touched.
12
X1
IN
Connected to GND.
13
X2
OUT
Terminal not used.
14
VSS
IN
15
OSC2
OUT
16
OSC1
IN
Internal clock oscillation frequency input setting.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit with
respect to OSC1 terminal.
17
TEST
IN
Connected to VC.
18
RES
IN
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily set "L"
level the moment power is applied, at this time the LSI is reset. Thereafter set at "H" level.
19
P20
OUT
Power source voltage: -5.0V.
VC voltage of power source circuit input.
Internal clock oscillation frequency control output.
Output to control oscillation input of OSC2.
Signal to sound buzzer (2.0 kHz).
A: key touch sound.
B: Completion sound.
0.1 sec.
H : GND
A
2.0 sec.
L : -5V
H : GND
B
L : -5V
20
P21
OUT
Terminal not used.
21
P22
22
P23
OUT
Clock output terminal to Memory IC4.
23
P24
OUT
Oven lamp, fan motor and turntable motor driving signal
16.7 msec.
To turn on and off shut off relay (RY1). The
square waveform voltage is delivered to the
RY1 driving circuit and RY2 control circuit.
IN/OUT Data input/output terminal to Memory IC4.
H : GND
L : -5V
During cooking
24
P25
OUT
Magnetron high-voltage circuit driving signal.
OFF
H : GND
To turn on and off the cook relay (RY2). The
signals holds "L" level during microwave cookP-HI
ON
L : -5V
ing and "H" level while not cooking. In other
OFF
OFF
H : GND
cooking modes (variable cooking) the signal
24 sec.
P-70
turns to "H" level and "L" level in repetition
8 sec.
ON
according to the power level.
L : -5V
(ON and OFF times for other power level.)
25-26
P26-P27
OUT
Terminal not used.
25
R-320CD/CK/CW
R-330CK/CW
Pin No.
Signal
I/O
27-29
P30-P32
OUT
Terminal not used.
30-34
P33-P37
OUT
Used for initial balancing of the bridge circuit (absolute humidity sensor).
35
CVCC
IN
Connected to GND.
36
VSS
IN
Power source voltage: -5.0V.
The power source voltage to the LSI is input to VSS terminal. Connected to VC.
37-38
V3-V2
IN
Terminal not used.
39-40
V1-V0
IN
Power source voltage input terminal.
Standard voltage for LCD. Connected to GND.
41
VCC
IN
Power source voltage: GND (0V).
The power source voltage to drive the LSI is input to VCC terminal.
42-45
COM4-COM1
OUT
Terminal not used.
46-65 SEG1-SEG20 OUT
Terminal not used.
66-79
Data output terminal to LCD driver IC3.
P74-P91
OUT
80-85 SEG35-SEG40 OUT
Description
Terminal not used.
86
P40
OUT
Terminal not used.
87
P41
IN
Signal similar to AN10.
When either G13 line on key matrix is touched, a corresponding signal will be input into P41.
88
P42
IN
Signal similar to AN10.
When either G12 line on key matrix is touched, a corresponding signal will be input into P42.
89
IRQ0
IN
Signal synchronized with commercial power source frequency.
This is the basic timing for time processing of LSI.
H : GND
L : -5V
16.7 msec.
90
AVCC
IN
A/D converter power source voltage.
The power source voltage to drive the A/D converter in the LSI. Connected to GND.
91
AN0
IN
Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is an
analog input terminal from the AH sensor circuit, and connected to the A/D converter built
into the LSI.
92
AN1
IN
AH sensor input.
This input is an analog input terminal from the AH sensor circuit, and connected to the A/
D converter built into the LSI.
93
AN2
IN
To input signal which communicates the door open/close information to LSI.
Door close "H" level signal (0V). Door open "L" level signal (-5V).
94
AN3
IN
Signal input terminal from thermistor (TH1).
95-98
AN4-AN7
IN
Terminal to change cooking input according to the Model.
By using the A/D converter contained in the LSI, DC voltage in accordance with the Model
in operation is applied to set up its cooking constant.
99
AN8
IN
Input terminal to judge the model.
The signal out of P17 will be input into AN8 through G1 line on key matrix. The LSI will judge
the model by this signal.
100
AN9
IN
Signal similar to AN10.
When either G11 line on key matrix is touched, a corresponding signal will be input into AN9.
26
R-320CD/CK/CW
R-330CK/CW
ABSOLUTE HUMIDITY SENSOR CIRCUIT
which the resistance balance of the bridge circuit is
deviated to increase the voltage available at AN1 terminal
of the LSI.
Then the LSI observes that voltage at AN1 terminal and
compares it with its initial value, and when the
comparison rate reaches the preset value (fixed for each
menu to be cooked), the LSI causes the unit to stop
sensor cooking; thereafter, the unit goes in the next
operation automatically.
When the LSI starts to detect the initial voltage at AN1
terminal 16 seconds after the unit has been put in the
Sensor Cooking mode, if it is not possible to balance the
bridge circuit due to disconnection of the absolute humidity
sensor, ERROR will appear on the display and the
cooking is stopped.
(1) Structure of Absolute Humidity Sensor
The absolute humidity sensor includes two thermistors
as shown in the illustration. One thermistor is housed in
the closed vessel filled with dry air while another in the
open vessel. Each sensor is provided with the protective
cover made of metal mesh to be protected from the
external airflow.
Thermistors
Sensing part
(Closed vessel)
(2) Operational Principle of Absolute Humidity Sensor
The figure below shows the basic structure of an absolute
humidity sensor. A bridge circuit is formed by two
thermistors and two resistors (R1 and R2).
The output of the bridge circuit is to be amplified by the
operational amplifier.
Each thermistor is supplied with a current to keep it
heated at about 150˚C (302˚F), the resultant heat is
dissipated in the air and if the two thermistors are placed
in different humidity conditions they show different
degrees of heat conductivity leading to a potential
difference between them causing an output voltage from
the bridge circuit, the intensity of which is increased as
the absolute humidity of the air increases. Since the
output is very minute, it is amplified by the operational
amplifier.
R3
R1
S
R2
Operational
amplifier
Output
voltage
+
S : Thermistor
open vessel
C : Thermistor
closed vessel
C. Thermistor in
closed vessel
S. Thermistor in
open vessel
R98
620k
30
R99
300k
31
R100
150k
32
R101
75k
33
R102
37.4k
34
R97
S
R93
360k
Absolute humidity vs,
output voltage characteristic
VA : -15V
Absolute humidity (g/m 2 )
(3) Detector Circuit of Absolute Humidity Sensor Circuit
This detector circuit is used to detect the output voltage
of the absolute humidity circuit to allow the LSI to control
sensor cooking of the unit. When the unit is set in the
sensor cooking mode, 16 seconds clearing cycle occurs
than the detector circuit starts to function and the LSI
observes the initial voltage available at its AN1 terminal.
With this voltage given, the switches SW1 to SW5 in the
LSI are turned on in such a way as to change the
resistance values in parallel with R107 ~ R111 of IC2.
Changing the resistance values results in that there is
the same potential at both F-3 terminal of the absolute
humidity sensor and AN0 terminal of the LSI. The voltage
of AN1 terminal will indicate about -2.5V. This initial
balancing is set up about 16 seconds after the unit is put
in the Sensor Cooking mode. As the sensor cooking
proceeds, the food is heated to generate moisture by
27
VA : -15V
SW1
P33
P34
P35
P36
P37
R95
47k
D90
VC : -5V
SW4
SW5
LSI
(IC1)
C92
R94
10k
SW2
SW3
AN0
0.01uF
0.015uF
C93
+
IC2
R90
F-2
R91
3.32k R92
1.8k
0.01uF
F-1
C
R96
F-3
3.57k
91
C91
47k
Output voltage
C
1) Absolute humidity sensor circuit
0.1
uF
Sensing part
(Open vessel)
C90
ventilation opening for sensing
92
AN1
R-320CD/CK/CW
R-330CK/CW
TOUCH CONTROL PANEL SERVICING
3) Re-connect the leads to the primary of the power
transformer.
4) Re-install the outer case (cabinet).
5) Re-connect the power supply cord after the outer
case is installed.
6) Run the oven and check all functions.
A. On some models, the power supply cord between the
touch control panel and the oven itself is so short that the
two can’t be separated. For those models, check and
repair all the controls (sensor-related ones included) of
the touch control panel while keeping it connected to the
oven.
B. On some models, the power supply cord between the
touch control panel and the oven proper is long enough
that they may be separated from each other. For those
models, it is possible to check and repair the controls of
the touch control panel while keeping it apart from the
oven proper; in this case you must short both ends of the
door sensing switch (on PWB) of the touch control panel
with a jumper, which activates an operational state that
is equivalent to the oven door being closed. As for the
sensor-related controls of the touch control panel, checking them is possible if dummy resistor(s) with resistance
equal to that of the controls are used.
(2) Servicing the touch control panel with power supply
from an external power source:
Disconnect the touch control panel completely from the
oven proper, and short both ends of the door sensing
switch (on PWB) of the touch control panel, which
activates an operational state that is equivalent to the
oven door being closed. Connect an external power
source to the power input terminal of the touch control
panel, then it is possible to check and repair the controls
of the touch control panel it is also possible to check the
sensor-related controls of the touch control panel by
using the dummy resistor(s).
1. Precautions for Handling Electronic Components
This unit uses CMOS LSI in the integral part of the
circuits. When handling these parts, the following
precautions should be strictly followed. CMOS LSI have
extremely high impedance at its input and output
terminals. For this reason, it is easily influenced by the
surrounding high voltage power source, static electricity
charge in clothes, etc. and sometimes it is not fully
protected by the built-in protection circuit.
In order to protect CMOS LSI.
1) When storing and transporting, thoroughly wrap them in
aluminium foil. Also wrap all PW boards containing them
in aluminium foil.
2) When soldering, ground the technician as shown in the
figure and use grounded soldering iron and work table.
approx. 1M ohm
2. Shapes of Electronic Components
E
C
B
Transistor
2SB1238
E
CB
Transistor
KRC243M
3. Servicing of Touch Control Panel
We describe the procedures to permit servicing of the
touch control panel of the microwave oven and the
precautions you must take when doing so. To perform
the servicing, power to the touch control panel is available
either from the power line of the oven itself or from an
external power source.
(1) Servicing the touch control panel with power supply
of the oven:
CAUTION:
THE HIGH VOLTAGE TRANSFORMER OF THE MICROWAVE OVEN IS STILL LIVE DURING SERVICING AND PRESENTS A HAZARD.
Therefore, before checking the performance of the touch
control panel,
1) Disconnect the power supply cord, and then remove
outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power
transformer.
5) Ensure that these leads remain isolated from other
components and oven chassis by using insulation
tape.
6) After that procedure, re-connect the power supply
cord.
After checking the performance of the touch control panel,
1) Disconnect the power supply cord.
2) Open the door and block it open.
4. Servicing Tools
Tools required to service the touch control panel assembly.
1) Soldering iron: 30W
(It is recommended to use a soldering iron with a
grounding terminal.)
2) Oscilloscope: Single beam, frequency range: DC-10MHz
type or more advanced model.
3) Others: Hand tools
5. Other Precautions
1) Before turning on the power source of the control unit,
remove the aluminium foil applied for preventing static
electricity.
2) Connect the connectors of the key unit to the control unit
being sure that the lead wires are not twisted.
3) After aluminium foil is removed, be careful that abnormal
voltage due to static electricity etc. is not applied to the
input or output terminals.
4) Attach connectors, electrolytic capacitors, etc. to PWB,
making sure that all connections are tight.
5) Be sure to use specified components where high precision is required.
28
R-320CD/CK/CW
R-330CK/CW
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
WARNING AGAINST HIGH VOLTAGE:
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may
result in severe, possibly fatal, electric shock.
(Example)
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
WARNING:
Avoid possible exposure to microwave energy. Please follow the instructions below before
operating the oven.
1. Disconnect the power supply cord.
2. Make sure that a definite” click” can be heard when the
microwave oven door is unlatched. (Hold the door in a
closed position with one hand, then push the door open
button with the other, this causes the latch leads to rise,
it is then possible to hear a “click’ as the door switches
operate.)
3. Visually check the door and cavity face plate for damage
(dents, cracks, signs of arcing etc.).
1.
2.
3.
4.
5.
6.
Door does not close firmly.
Door hinge, support or latch hook is damaged.
The door gasket or seal is damaged.
The door is bent or warped.
There are defective parts in the door interlock system.
There are defective parts in the microwave generating
and transmission assembly.
7. There is visible damage to the oven.
Do not operate the oven:
1. Without the RF gasket (Magnetron).
2. If the wave guide or oven cavity are not intact.
3. If the door is not closed.
4. If the outer case (cabinet) is not fitted.
Carry out any remedial work that is necessary before
operating the oven.
Do not operate the oven if any of the following conditions
exist;
WARNING FOR WIRING
To prevent an electric shock, take the following precautions.
1. Before wiring,
1) Disconnect the power supply cord.
2) Open the door block it open.
3) Discharge the high voltage capacitor and wait for 60
seconds.
2. Don’t let the wire leads touch to the following parts;
1) High voltage parts:
Magnetron, High voltage transformer, High voltage
capacitor and High voltage rectifier assembly.
2) Hot parts:
Oven lamp, Magnetron, High voltage transformer
and Oven cavity.
3) Sharp edge:
Bottom plate, Oven cavity, Waveguide flange,
Chassis support and other metallic plate.
4) Moveable parts (to prevent a fault)
Fan blade, Fan motor, Switch, Switch lever, Open
button.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector until its pin is locked
and make sure that the wire leads do not come off even
if the wire leads are pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
Please refer to ‘OVEN PARTS, CABINET PARTS, CONTROL PANEL PARTS, DOOR PARTS’, when carrying out any of
the following removal procedures:
OUTER CASE REMOVAL
To remove the outer case, proceed as follows.
1. Disconnect the power supply cord.
2. Open the oven door and block it open.
3. Remove the two (2) screws from the lower portion of the
rear cabinet using a T20H Torx type or GTXH20-100
screw driver.
4. Remove the remaining two (2) screws from rear and one
(1) screw along the right side of outer case.
5. Slide the entire outer case back out about 1 inch (3 cm)
to free it from retaining clips on the cavity face plate.
6. Lift entire outer case from the unit.
29
R-320CD/CK/CW
R-330CK/CW
CAUTION: 1. DISCONNECT OVEN FROM POWER SUP
PLY BEFORE REMOVING OUTER CASE.
2. DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN
COMPONENTS OR WIRING.
NOTE: When replacing the outer case, the 2 special
Torx screws must be reinstalled in the same
locations.
Special screw
Screw Driver
(Type: TORX T20 H or
GTXH20-100)
POWER TRANSFORMER REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads (primary and high voltage) from
power transformer and the filament leads from the
magnetron and capacitor terminals.
5. Remove four (4) screws holding transformer to bottom
plate.
6. Remove transformer from bottom plate.
Re-instal
1. Rest transformer on the bottom plate with its primary
terminals toward the oven face plate.
2. Secure transformer with four screws to bottom plate.
3. Re-connect wire leads (primary and high voltage) to
power transformer and filament leads of transformer to
magnetron and high voltage capacitor. Refer to
"PICTORIAL DIAGRAM" on page 35.
4. Re-install outer case and check that oven is operating
properly.
TERMINAL INSULATOR REPLACEMENT
Installation
1. Insert the receptacle into terminal insulator.
2. Close covers of the terminal insulator, as shown below.
3. Reconnect all leads removed from components during
testing.
4. Reinstall the outer case (cabinet).
5. Reconnect the power supply cord after the outer case is
installed.
6. Run the oven and check all functions.
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Open covers of the terminal insulator by using small flat
type screw driver.
5. Remove the receptacle from the terminal insulator.
6. Now, the terminal insulator is free.
COVERS
Terminal
insulator
Flat type
screw driver
RECEPTACLE
HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the high voltage wire B from the power
transformer.
5. Disconnect the high voltage wire of high voltage rectifier
assembly from the magnetron.
6. Disconnect the filament lead (short one) of the power
transformer from the high voltage capacitor.
7. Remove one (1) screw holding capacitor holder to oven
cavity rear plate.
8. Remove one (1) screw holding high voltage rectifier
assembly to capacitor holder.
9. Disconnect rectifier terminal from capacitor.
High voltage rectifier assembly is now free.
10.Disconnect the high voltage wire B from the high voltage
capacitor.
11.Remove capacitor holder. Capacitor is now free.
CAUTION: WHEN REPLACING HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR,
GROUND SIDE TERMINAL OF THE HIGH
VOLTAGE RECTIFIER MUST BE SECURED
FIRMLY WITH A GROUNDING SCREW.
30
R-320CD/CK/CW
R-330CK/CW
MAGNETRON REMOVAL
Removal
1. Disconnect the power supply cord and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads from magnetron.
5. Remove the four (4) screws holding chassis support to
magnetron, oven cavity back plate, oven cavity front
flange and fan duct.
6. Remove the chassis support from oven.
7. Carefully remove the four (4) screws holding magnetron
to waveguide flange.
8. Lift up magnetron with care so that magnetron antenna
is not hit by any metal object around antenna.
9. Now, the magnetron is free.
Re-install
1. Re-install the magnetron to waveguide flange with the
four (4) screws.
2. Insert the two (2) tabs of the chassis support to the oven
cavity front plate and the back plate.
3. Hold the chassis support to the oven cavity back plate,
oven cavity front flange, magnetron and the fan duct with
the four (4) screws.
4. Re-install the chassis support to magnetron with the one
(1) screw.
5. Reconnect the wire leads to the magnetron. Refer to
"PICTORIAL DIAGRAM" on page 35.
6. Re-install outer case and check that the oven is operating
properly.
CAUTION: WHEN REPLACING MAGNETRON, BE SURE
THE R.F. GASKET IS IN PLACE AND MOUNTING SCREWS ARE TIGHTENED SECURELY
OVEN LAMP AND LAMP SOCKET REMOVAL
1. Disconnect the power supply cord and then remove outer
case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the oven lamp from the oven lamp socket.
5. Pull the wire leads from the oven lamp socket by pushing
the terminal hole of the oven lamp socket with the small
flat type screw driver.
6. Bend the tab of the partition angle holding the lamp
socket.
7. Lift up the oven lamp socket.
8. Now, the oven lamp socket is free.
Oven lamp
socket
Terminal
Wire lead
Terminal hole
Flat type small
screw driver
Figure C-1. Oven lamp socket
POSITIVE LOCK® CONNECTOR (NO-CASE TYPE) REMOVAL
Terminal
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Push the lever of positive lock® connector.
5. Pull down on the positive lock ® connector.
Positive lock®
connector
4
Push
Lever
CAUTION: WHEN CONNECTING THE POSITIVE LOCK®
CONNECTORS TO THE TERMINALS, CONNECT THE POSITIVE LOCK® SO THAT THE
LEVER FACES YOU
5
Pull down
Figure C-2. Positive lock® connector
CONTROL PANEL ASSEMBLY REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads from the door sensing switch and
the oven cavity front flange.
5. Disconnect the wire leads from panel components.
6. Make one (1) tab of the oven cavity front plate straight
holding the control panel assembly to the oven flange.
7. Slide the control panel assembly upward and remove it.
8. Now, individual components can be removed.
NOTE: 1. Before attaching a new key unit, wipe off remaining
adhesive on the control panel frame surfaces
completely with a soft cloth soaked in alcohol.
2. When attaching the key unit to the control panel
frame, adjust the upper edge and right edge of
the key unit to the correct position of control panel
frame.
31
R-320CD/CK/CW
R-330CK/CW
3. Stick the key unit firmly to the control panel frame
by rubbing with soft cloth not to scratch.
CPU UNIT
NOTE: Handle the CPU unit carefully so that the ribbon
cable does not come off. Because the ribbon cable
is glued on the LCD and the printed wiring board
only by heated paste.
Printed wiring board
of CPU unit
Liquid Crystal
Display (LCD)
Ribbon cable
CPU unit
COOLING FAN MOTOR REMOVAL
15.Remove the two (2) screws holding the fan motor to the
fan duct.
16.Now, the fan motor is free.
REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the fan motor.
5. Remove the magnetron and chassis support from the
waveguide flange, referring to "MAGNETRON
REMOVAL".
6. Release the snap of the main wire harness from the fan duct.
7. Remove one (1) screw holding the fan duct assembly to
oven cavity.
8. Release the main wire harness from the hole of the fan duct.
9. Release the fan duct from the waveguide flange.
10.Release the fan duct assembly from the oven cavity.
11.Remove the fan blade from the fan motor shaft according
to the following procedure.
12.Hold the edge of the rotor of the fan motor by using a pair
of groove joint pliers.
CAUTION:
* Make sure that no metal pieces enter the gap between
the rotor and the stator of the fan motor because the
rotor is easily shaven by pliers and metal pieces may
be produced.
* Do not touch the pliers to the coil of the fan motor
because the coil may be cut or injured.
* Do not disfigure the bracket by touching with the
pliers.
13.Remove the fan blade from the shaft of the fan motor by
pulling and rotating the fan blade with your hand.
14. Now, the fan blade will be free.
CAUTION:
* Do not reuse the removed fan blade because the
hole (for shaft) may be larger than normal.
INSTALLATION
1. Install the fan motor to the fan duct with the two (2)
screws.
2. Install the fan blade to the fan motor shaft according to
the following procedure.
3. Hold the center of the bracket which supports the shaft
of the fan motor on the flat table.
4. Apply the screw lock tight into the hole (for shaft) of the
fan blade.
5. Install the fan blade to the shaft of fan motor by pushing
the fan blade with a small, light weight, ball peen hammer
or rubber mallet.
CAUTION:
* Do not hit the fan blade strongly when installed
because the bracket may be disfigured.
* Make sure that the fan blade rotates smooth after
installation.
* Make sure that the axis of the shaft is not slanted.
6. Catch three holes of fan duct on three tabs of the
waveguide flange.
7. Install the fan duct assembly to the oven cavity with the
one (1) screw.
8. Insert the snap of the main wire harness to the hole of the
fan duct and insert the main wire harness into the hole of
the fan duct.
9. Install the magnetron and the chassis support to the
oven cavity, referring to "Re-install of MAGNETRON
REMOVAL".
10.Connect the wire leads to the fan motor, referring to the
pictorial diagram.
Coil
Groove joint pliers
Shaft
Shaft
Axis
Stator
Gap
Bracket
Stator
Rotor
Rear View
These are the positions
that should be pinched
with pliers
Rotor
Side View
32
Table
Center of
bracket
R-320CD/CK/CW
R-330CK/CW
TURNTABLE MOTOR REMOVAL
5. Disconnect wire leads from turntable motor.
(See "Positive lock connector removal")
6. Remove two (2) screws holding turntable motor to oven
cavity.
7. Now the turntable motor is free.
8. After replacement use the one (1) screw to fit the
turntable motor cover.
1. Disconnect the power supply cord.
2. Remove turntable and turntable support from oven cavity.
3. Lay the oven on it's backside. Remove the turntable
motor cover by snipping off the material in four corners.
4. Where the corners have been snipped off bend corner
areas flat. No sharp edges must be evident after removal
of the turntable motor cover.
DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL
Re-install
1. Re-install each switch in its place. The secondary
interlock/monitor switches are in the lower position and
the door sensing switch is in the upper position.
2. Re-connect wire leads to each switch.
Refer to pictorial diagram.
3. Secure latch hook (with two (2) mounting screws) to
oven flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit. Refer to
chapter "Test Procedure" and Adjustment procedure.
1.
2.
3.
4.
5.
6.
7.
Disconnect the power supply cord and remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect wire leads from the switches.
Remove two (2) screws holding latch hook to oven flange.
Remove latch hook assembly from oven flange.
Push outward on the two (2) retaining tabs holding switch
in place.
8. Switch is now free.
At this time switch lever will be free, do not lose it.
DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
If the door sensing switch, secondary interlock switch
and monitor switch do not operate properly due to a
misadjustment, the following adjustment should be made.
4. Loosen the two (2) screws holding latch hook to the oven
cavity front flange.
5. With door closed, adjust latch hook by moving it back and
forth, and up and down. In and out play of the door
allowed by the upper and lower position of the latch hook
should be less than 0.5mm. The vertical position of the
latch hook should be adjusted so that the door sensing
switch and secondary interlock switch are activated with
the door closed. The horizontal position of the latch hook
should be adjusted so that the plunger of the monitor
switch is pressed with the door closed.
6. Secure the screws with washers firmly.
7. Check the operation of all switches. If each switch has
not activated with the door closed, loosen screw and
adjust the latch hook position.
hook, pushing and pulling upper portion of door toward
the oven face. Then check lower portion of the latch
hook, pushing and pulling lower portion of the door
toward the oven face. Both results (play in the door)
should be less than 0.5mm.
2. The door sensing switch and secondary interlock switch
interrupt the circuit before the door can be opened.
3. Monitor switch contacts close when door is opened.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Door
Latch Hook
Latch
Heads
Door Sensing
Switch
Monitor Switch
Switch Lever
After adjustment, check the following.
1. In and out play of door remains less than 0.5mm when in
the latched position. First check upper position of latch
Secondary
Interlock Switch
Figure C-3. Latch Switch Adjustments
DOOR REPLACEMENT
REMOVAL
1. Disconnect the power supply cord.
2. Push the open button and open the door slightly.
3. Insert a putty knife (thickness of about 0.5mm) into the
gap between the choke cover and door frame as shown
in Figure C-4 to free engaging parts.
33
R-320CD/CK/CW
R-330CK/CW
4. Pry the choke cover by inserting a putty knife as shown
Figure C-4.
5. Release choke cover from door panel.
6. Now choke cover is free.
7. Release two (2) pins of door panel from two (2) holes of
upper and lower oven hinges by lifting up.
8. Now, door panel with door frame is free from oven cavity.
approved microwave survey meter. (Refer to Microwave
Measurement Procedure.)
Note: The door on a microwave oven is designed to act as
an electronic seal preventing the leakage of
microwave energy from oven cavity during cook
cycle. This function does not require that door be airtight, moisture (condensation)-tight or light-tight.
Therefore, occasional appearance of moisture, light
or sensing of gentle warm air movement around
oven door is not abnormal and do not of themselves
indicate a leakage of microwave energy from oven
cavity.
Choke Cover
Door Frame
Pin
Putty Knife
Upper
Oven Hinge
Figure C-4. Door Disassembly
9. Remove the four (4) screws holding the door panel to the
door frame.
10.Release door panel from eight (8) tabs of door frame.
11.Now, door panel with sealer film is free.
12.Tear sealer film from door panel.
13.Now, door panel is free.
14.Slide latch head upward and remove it from door frame
with releasing latch spring from door frame and latch
head.
15.Now, latch head and latch spring are free.
16.Remove door screen from door frame.
17.Now, door screen is free.
Upper Oven
Hinge
Door Panel
Lower
Oven Hinge
Lower Oven
Hinge
RE-INSTALL
1. Re-install door screen to door frame.
2. Re-install the latch spring to the latch head. Re-install the
latch spring to the door frame. Re-install latch head to
door frame.
3. Re-install door panel to door frame by fitting eight (8)
tabs of door frame to eight (8) holes of door panel.
4. Hold the door panel to the door frame with the four (4)
screws.
5. Put sealer film on door panel. Refer to “Sealer Film”
about how to handle new one.
6. Catch two (2) pins of door panel on two (2) hole of upper
and lower oven hinges.
7. Re-install choke cover to door panel by pushing.
Pin
Choke Cover
Figure C-5. Door Replacement
SEALER FILM
Installation
1. Put the adhesive tape on the backing film of the sealer
film as shown in Fig. C-6.
2. Tear the backing film by pulling the adhesive tape.
3. Put the pasted side of the sealer film on the door panel
Sealer film
Note: After any service to the door;
(A) Make sure that door sensing switch and secondary
interlock switch are operating properly. (Refer to
chapter “Test Procedures”.).
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
After any service, make sure of the following :
1. Door latch heads smoothly catch latch hook through
latch holes and that latch head goes through center of
latch hole.
2. Deviation of door alignment from horizontal line of cavity
face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity
face plate.
4. Check for microwave leakage around door with an
Backing film
Adhesive tape
Figure C-6. Sealer film
34
H
1
2
3
35
RY2
COM.
1
2
N.O.
CN-A
N.O.
COM.
SH-B
T1
RY1
PRIMARY
INTERLOCK
RELAY
SH-A
(POWER UNIT)
CN-C
GRN
GRY
YLW
YLW
CN-A
1 WHT
2
CN-F
4
5
COM.
SECONDARY NO
INTERLOCK
SWITCH
MONITOR
SWITCH
WHT
GRY
WHT
TURNTABLE
MOTOR
WHT
BLK
WHT
GRY
BLK
BLK
GRY
RED
GRY
BLK
MAGNETRON
POWER
TRANSFORMER
HIGH VOLTAGE
WIRE B
HIGH VOLTAGE
CAPACITOR
HIGH VOLTAGE COMPONENTS
BLK
THERMAL
CUT-OUT (MG)
NOTE:
The neutral (WHT) wire must be
connected to the terminal with "N"
mark on the power supply cord.
5
Figure S-1. Pictorial Diagram
BLK
MONITOR
FUSE
&
HOLDER
BLK
FAN MOTOR
THERMAL
CUT-OUT (OVEN)
POWER SUPPLY
CORD 120V 60Hz
N
4
WHT
WHT
E
COM.
GRN
GRN
BLK
WHT
H
3
N.C.
RED
F
BLK
RED
RED
(CPU UNIT)
GRY
GRN
BLK
WHT
BLK
2
BLK
YLW
G
CN-G
N.O.
NOTE:
Hot (YLW) wire must be
connected to the terminal
with blue mark on the
oven light socket.
A
COM.
DOOR
SENSING
SWITCH
OVEN LAMP
AND SOCKET
D
CONTROL PANEL
AH SENSOR
YLW
WHT
C
CN-F
1 BLK
2 RED
3 WHT
B
NOTE:
The grounding conductor of
the power supply cord has
been grounded by power
supply cord fixing screw.
The screw must always be
kept tight.
1
H.V.
RECTIFIER
BLUE MARK
R-320CD/CK/CW
R-330CK/CW
6
A
6
B
C
D
E
F
G
H
R-320CD/CK/CW
R-330CK/CW
2
1
4
3
6
5
A
A
CN-C
12PIN LEAD
WIRE HARNESS
B
Q2 2SB1238
b
+
–
LED
C2
GND
+
–
C4 10µ/35v
a
1SS270A
C3 0.1µ/50v
d
C
1SS270A
C10
B
R5 4.7k
ZD1
HZ16-1
A2
D6
C1 0.1µ/50v
AC
10G471K
A1
VRS1
CN-A
D5
C2 1000µ/35v
D1-D4
11ES1
T1
R1 2.4k
R4 27
C
C3
VC
C1
VA
C4
INT
C9
VR
C5
BUZZER
C6
OVEN LAMP
TURNTABLE
MOTOR
FAN MOTOR
R3 510 1/2w
(J1)
Q1 2SB1238
R2 680 1/2w
c
D
D
SP1 PKM22EPT
Q3 KRC243M
R6 3.3k
+
E
–
D8
NO
COM
1SS270A
RY2
MICRO
C5 10µ/35v
COM
AC
1SS270A
RY1
NO
D7
OVEN LAMP
TURNTABLE
MOTOR
FAN MOTOR
SH-A
F
DOOR
SENSING
SWITCH
C7
MICRO
C8
NC
C11
NC
C12
DOOR
SWITCH
E
F
SH-B
G
G
H
H
Figure S-2. Power Unit Circuit
1
2
4
3
36
5
6
37
C-11
C-8
(BROWNER)
NC
C-12
C-7
DOOR
MICRO
C-6
C-5
BUZZER
OVEN LAMP
TURNTABLE
MOTOR
FAN MOTOR
C-1
C-9
C-10
VA
VR
LED
C-3
NOTE
D41 1SS355
D20 1SS355
4
C12
0.1µ
/50v
C11 0.1µ/50v
AH SENSOR
F-2
C20
0.1µ/50v
F-1
Q21 DTA123JKA
Q20
DTA143EKA
Q30
DTA143EKA
R90 330 1w
IC2
BA4558
6
4
IC2
5 +
8
R10 1k
ZD10
UDZ4.3B
D90
MA152WA
R92 1.8kF
C90
0.1µ/50v
D
5
R73 15k
R72 15k
R71 15k
R70 15k
R69 15k
R68 15k
E
R41 15k
B
A
R97 47k
R94 10k R95 47k
C
R93 360kF
7
Q10
2SA1037AK
100
G14
G13
KEY UNIT
Stop
Clear
Frozen
Rolls/
Muffins
Ground Meat
(COMPU DEFROST)
Power
Level
Frozen
Entrees
CUSTOM
HELP
Kitchen
Timer
7
2
G5
Beverage
Clock
Chicken
Breast
Minute
Plus
8
9
G11
3
4
0
G6
G10
G12
IC1
IZA949DR
G7
5
1
G9
G8
80
SEG36
SEG37
SEG38
SEG39
SEG40
P40
P41
P42
IRQ0
AVCC
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
81
COOK SENSOR LBS KG DEF HELP
LIQUID CRYSTAL DISPLAY
50
30
31
SEG5
SEG4
SEG3
SEG2
SEG1
COM1
COM2
COM3
COM4
VCC
V0
V1
V2
V3
VSS
CVCC
P37
P36
P35
P34
51
Chicken
Pieces
Steaks/
Chops
1
6
Rice
R14
10k
A
E
D
C
B
R15
10k
CF1
CST4.00MGW
Popcorn
G2
Fresh
Fresh
Fish/
Rolls/
Muffins vegetables seafood
REHEAT
SENSOR
Start
G3
G4
R13
10k
Ground Meat
(SENSOR COOK)
Frozen
vegetables
Baked
Potatoes
G1
4
5
6
C62 330pF/50v
Figure S-3. CPU Unit Circuit For R-320CD/CK/CW
F-3
C13
0.01µ
/25v
: IF NOT SPECIFIED, 1/10W ± 5%
C10 47µ/16v
LD4 LD3 LD2 LD1
Q11
DTA143EKA
R12
15k
R96 3.57kD
R91 3.32kD
VC
–
R100 150kF
R79 270k
+
R99 300k
R78 270k
R77 270k
R76 270k
R75 270k
R102 37.4kF
C14
0.01µ/25v
R11
15k
(J10)
(J11)
R98 620k
C40
0.01µ/25v
C91
0.015µ/25v
R101 75kF
R40 4.7k
4.7k
R74 270k
CPU UNIT
C63 330pF/50v
C-2
4.7k
C64 330pF/50v
(J14)
(J15)
C-4
4.7k
C61 330pF/50v
(J16)
(J17)
C60 330pF/50v
(J12)
(J13)
C92
0.01µ/25v
C65 330pF/50v
4.7k
C93
0.01µ/25v
GND
R67 15k
3
R65 15k
2
R64 15k
H
R63 15k
1
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
G
AN10
AN11
AVSS
P10
P11
P12
P13
P14
P15
P16
P17
X1
X2
VSS
OSC2
OSC1
TEST
RES
P20
P21
P22
P23
P24
P25
P26
P27
P30
P31
P32
P33
F
R80
1M
E
3
R62 15k
C
R66 15k
A
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG0
COM0
COM1
COM2
D
2
R61 15k
1
R60 15k
B
INT
R-320CD/CK/CW
R-330CK/CW
6
A
B
C
D
E
F
G
H
3
38
C-11
C-8
(BROWNER)
NC
C-12
C-7
DOOR
MICRO
C-6
C-5
BUZZER
OVEN LAMP
TURNTABLE
MOTOR
FAN MOTOR
C-1
C-9
C-10
C-3
VA
VR
LED
VC
NOTE
D41 1SS355
D20 1SS355
LD19 LD18 LD17
LD10 LD11 LD12
–
+
C12
0.1µ
/50v
C11 0.1µ/50v
4
AH SENSOR
F-2
C20
0.1µ/50v
F-1
Q21 DTA123JKA
Q20
DTA143EKA
Q30
DTA143EKA
R90 330 1w
F-3
6
4
IC2
5 +
D
5
R73 15k
R72 15k
R71 15k
R70 15k
R69 15k
R68 15k
E
R41 15k
B
A
R97 47k
R94 10k R95 47k
C
R93 360kF
7
R111 15k
100
IC1
IZA950DR
Baked
potatoes
Sensor
reheat
Popcorn
G13
KEY UNIT
Lunch on
the Run
Stop
Clear
One Dish
Dinners
G12
G14
Clock
Frozen
snacks
Minute
Plus
G11
8
9
0
3
4
G10
G6
G7
5
1
Indicator Circuit
( See Fig. S-5 )
G9
G8
80
SEG36
SEG37
SEG38
SEG39
SEG40
P40
P41
P42
IRQ0
AVCC
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
81
IC4
AT24C01A
30
31
Breakfast
Bar
Custom
Help
Power
Level
Super
Defrost
Frozen
vegetables
Start
Touch On
Kitchen
Timer
Fish/
seafood
Poultry
Compu
Defrost
6
7
Rice
Beverage
center
1
2
G2
A
E
D
C
B
CF1
CST4.00MGW
G3
R61 15k
G4
G5
50
SEG5
SEG4
SEG3
SEG2
SEG1
COM1
COM2
COM3
COM4
VCC
V0
V1
V2
V3
VSS
CVCC
P37
P36
P35
P34
51
Frozen
entrees
Ground
meat
Fresh
vegetables
G1
4
5
C62 330pF/50v
4.7k
Figure S-4. CPU Unit Circuit For R-330CK/CW
R92 1.8kF
IC2
BA4558
8
R10 1k
ZD10
UDZ4.3B
D90
MA152WA
Q10
2SA1037AK
CPU UNIT
3
: IF NOT SPECIFIED, 1/10W ± 5%
C10 47µ/16v
LD16 LD15 LD14 LD13
Q11
DTA143EKA
R12
15k
R96 3.57kD
R91 3.32kD
C13
0.01µ
/25v
C90
0.1µ/50v
C-2
R102 37.4kF
C14
0.01µ/25v
R11
15k
R100 150kF
R79 270k
R110
1.5k
TH1
C-4
R99 300k
R78 270k
R77 270k
R76 270k
R75 270k
GND
4.7k
C64 330pF/50v
(J14)
(J15)
C63 330pF/50v
(J16)
(J17)
C61 330pF/50v
(J10)
(J11)
R98 620k
C40
0.01µ/25v
C91
0.015µ/25v
R101 75kF
R40 4.7k
4.7k
R74 270k
4.7k
C93 0.01µ/25v
(J12)
(J13)
C92
0.01µ/25v
C65 330pF/50v
C100 0.01µ/25v
R66 15k
2
C60 330pF/50v
GND
A2
A1
A0
SDA
SCL
WP
VCC
1
R65 15k
H
R64 15k
G
SEG35
P91
P90
P87
P86
P85
P84
P83
P82
P81
P80
P77
P76
P75
P74
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
E
AN10
AN11
AVSS
P10
P11
P12
P13
P14
P15
P16
P17
X1
X2
VSS
OSC2
OSC1
TEST
RES
P20
P21
P22
P23
P24
P25
P26
P27
P30
P31
P32
P33
D
C110
0.01µ
/25v
C
R67 15k
B
R63 15k
A
R80
1M
F
2
R62 15k
1
R60 15k
INT
R-320CD/CK/CW
R-330CK/CW
6
A
B
C
6
D
E
F
G
H
3
39
4
IC1 P74
NOTE
R127 4.7k
R134 15k
R126 4.7k
R125 4.7k
R124 4.7k
R123 4.7k
: IF NOT SPECIFIED, 1/10W ± 5%
75
76
LIQUID CRYSTAL DISPLAY
4
5
5
Figure S-5. Indicator Circuit For R-330CK/CW
C123 0.1µ/50v
C122 0.1µ/50v
C121 0.1µ/50v
51
OSC4
OSC3
VD1
OSC2
OSC1
VSS
BZ
COM0
COM1
COM2
COM3
COM4
COM5
COM6
COM7
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
IC3
IZA951DR
100
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
1
COOK HELP
IC1 P75
C125
0.1µ/50v
C120 0.1µ/50v
50
VDD
NC
NC
RESET
TEST
VREF
R03
R02
R01
R00
P13
P12
P11
P10
P03
P02
P01
P00
K03
K02
K01
K00
NC
NC
NC
26
A
IC1 P76
IC1 P77
IC1 P80
IC1 P81
IC1 P82
IC1 P83
IC1 P84
IC1 P85
G
IC1 P86
IC1 P87
IC1 P90
IC1 P91
GND
R133 510k
R132 33k
C126
0.1µ/50v 25
E
R128 4.7k
D
C124 0.1µ/50v
R130 4.7k
VC
SENSOR DEFROST
C127
0.1µ/50v
2
3
C128
0.1µ/50v
1
2
C129
0.1µ/50v
1
VC1
VC2
VC3
VC4
VC5
CF
CE
CD
CC
CB
CA
COM8
COM9
COM10
COM11
COM12
COM13
COM14
COM15
COM16
SEG39
SEG38
SEG37
SEG36
SEG35
B
COM16
COM15
COM14
COM13
COM12
COM11
COM10
COM9
SEG40
SEG39
SEG38
SEG37
SEG36
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
COM1
COM2
COM3
COM4
COM5
COM6
COM7
COM8
R-320CD/CK/CW
R-330CK/CW
6
A
B
C
C
F
H
6
D
E
F
G
H
R131 4.7k
R129 4.7k
R122 4.7k
R121 4.7k
R120 4.7k
R-320CD/CK/CW
R-330CK/CW
2
1
4
3
6
5
A
A
B
(CN - C)
1
12
2
1 2
C5
4
E
5
6
ZD1
R1
B
Q3
SP1
1
D7
VRB
C
2
7
8
9
U
SH - A
R2
D5
D6
SH - B
B
Q2
E Q1 B
R5
R4
3
R3
D8 R6
D
CN - C
1
WH - 1
C4
C
B
1
9
E
C3
CN - B
D
D
C2
RY2
P
T1
AC
1
VH
VRS1
D1
D3
E
2
CN - A
XA
D9
AC
RY1
G
F
(CN - D)
OMIF
D U
QKITPB026MRE0
F
D4
D2
S
E
F
11
C1
10
(D10)
OL FM
TTM
RY3
G
H
H
Figure S-6. Printed Wiring Board of Power Unit
1
2
4
3
40
5
6
R-320CD/CK/CW
R-330CK/CW
PARTS LIST
Note: The parts marked “ ∆” may cause undue microwave exposure.
The parts marked “*” are used in voltage more than 250V.
REF. NO.
PART NO.
DESCRIPTION
Q'TY
CODE
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AH
AH
AS
AL
AP
AV
AP
AX
AV
BK
AV
AH
AG
AE
AU
AS
AP
BM
BC
1
1
1
1
1
1
2
1
BD
AZ
AZ
AZ
AZ
AX
AC
AH
1
1
1
1
1
1
1
1
2
4
4
5
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
BC
AC
AE
AD
AD
AA
AF
AA
AA
AB
AA
AC
AA
AB
AA
AA
AB
AB
AA
AA
AK
AL
AG
AP
AE
AA
BK
BK
BK
BK
BK
BC
BC
BC
BC
BC
ELECTRIC PARTS
*
*
*
∆*
*
1- 1
1- 2
1- 3
1- 4
1- 5
1- 5
1- 6
1- 7
1- 7
1- 8
1- 9
1-10
1-11
1-11
1-12
1-12
1-13
1-14
1-15
QSW-MA137WRE0
QFSHDA009WRE0
FFS-BA023WRK0
RTHM-A078WRE0
FACCDA081WRE0
FACCDA082WRE0
FH-DZA088WRK0
RC-QZA173WRE0
RC-QZA211WRE0
RV-MZA288WRE0
RMOTEA383WRE0
QSOCLA021WRE0
RLMPTA068WRE0
RLMPTA030WRE0
RMOTDA161WRE0
RMOTDA211WRE0
RTHM-A080WRE0
RTRN-A576WRE0
FDTCTA197WRK0
2nd interlock switch / door sensing switch
Fuse holder
Monitor fuse and monitor switch assembly
Thermal cut-out 125 deg.
Power supply cord
Power supply cord (Interchangeable)
High voltage rectifier assembly
High voltage capacitor
High voltage capacitor (Interchangeable)
Magnetron
Fan motor
Oven lamp socket
Oven lamp
Oven lamp (Interchangeable)
Turntable motor
Turntable motor (Interchangeable)
Thermal cut-out 145 deg.
Power transformer
AH sensor assembly
22222222-
GCABUA702WRP0
GCABUA687WRP0
GCABUA687WRP0
GCABUA690WRP0
GCABUA690WRP0
GDAI-A316WRW0
GLEGPA074WRE0
GLEGPA077WRF0
Outer case cabinet
Outer case cabinet
Outer case cabinet
Outer case cabinet
Outer case cabinet
Bottom plate
Foot
Leg
CPWBFA775WRK0
QCNCMA446DRE0
FW-VZA232DRE0
FW-VZA195DRE0
FW-VZA197DRE0
RC-KZA087DRE0
VCEAB31VW108M
RC-KZA087DRE0
VCEAB31VW106M
VHD11ES1///-1
VHD1SS270A/-1
VHPSLZ381A9-3
VS2SB1238//-3
VSKRC243M//-3
VRD-B12EF242J
VRD-B12HF681J
VRD-B12HF511J
VRD-B12EF270J
VRD-B12EF472J
VRD-B12EF332J
RRLY-A076DRE0
RRLY-A081DRE0
RALM-A014DRE0
RTRNPA111DRE0
RH-VZA032DRE0
VHEHZ161///-1
DPWBFB917WRK0
DPWBFB917WRK0
DPWBFB917WRK0
DPWBFB918WRK0
DPWBFB918WRK0
FPNLCB422WRK0
FPNLCB423WRK0
FPNLCB424WRK0
FPNLCB425WRK0
FPNLCB432WRK0
Power unit
2-pin connector (CN-A)
12pin lead wire (CN-C)
Switch harness A (SH-A)
Switch harness B (SH-B)
Capacitor
0.1 uF
50V
Capacitor
1000 uF
35V
Capacitor
0.1 uF
50V
Capacitor
10 uF
35V
Diode (11ES1)
Diode (1SS270ATA)
Light emitting diode
Transistor (2SB1238)
Transistor (KRC243M)
Resistor
2.4k ohm
1/4W
Resistor
680 ohm
1/2W
Resistor
510 ohm
1/2W
Resistor
27 ohm
1/4W
Resistor
4.7k ohm
1/4W
Resistor
3.3k ohm
1/4W
Relay (OMIF-S-124LM)
Relay (VRB24)
Buzzer (PKM22EPT)
Transformer
Varistor (10G471K)
Zener diode (HZ16-1)
CPU unit [R-320CD]
CPU unit [R-320CK]
CPU unit [R-320CW]
CPU unit [R-330CK]
CPU unit [R-330CW]
Control panel frame with key unit
Control panel frame with key unit
Control panel frame with key unit
Control panel frame with key unit
Control panel frame with key unit
CABINET PARTS
1
1
1
1
1
2
3
4
[R-320CD]
[R-320CK]
[R-330CK]
[R-320CW]
[R-330CW]
CONTROL PANEL PARTS
3- 1
3- 1A
3- 1B
3- 1C
3- 1D
C1
C2
C3
C4-5
D1-4
D5-8
LD1-5
Q1-2
Q3
R1
R2
R3
R4
R5
R6
RY1
RY2
SP1
T1
VRS1
ZD1
3- 2
3- 2
3- 2
3- 2
3- 2
3- 3
3- 3
3- 3
3- 3
3- 3
41
[R-320CK]
[R-330CK]
[R-320CW]
[R-330CW]
[R-320CD]
R-320CD/CK/CW
R-330CK/CW
REF. NO.
3- 3-1
3- 3-1
3- 3-1
3- 3-1
3- 3-1
3- 4
3- 4
3- 4
3- 4
3- 4
3- 5
3- 6
3- 6
3- 6
3- 6
3- 6
3- 7
3- 7
3- 7
3- 7
3- 7
3- 8
PART NO.
FUNTKA923WRE0
FUNTKA924WRE0
FUNTKA925WRE0
FUNTKA926WRE0
FUNTKA934WRE0
JBTN-B100WRF0
JBTN-B100WRF0
JBTN-B101WRF0
JBTN-B101WRF0
JBTN-B102WRF0
MSPRCA050WRE0
PSHEPA588WRE0
PSHEPA588WRE0
PSHEPA588WRE0
PSHEPA672WRE0
PSHEPA672WRE0
LHLD-A185WRF0
LHLD-A185WRF0
LHLD-A204WRF0
LHLD-A204WRF0
LHLD-A204WRF0
XEPSD30P08XS0
DESCRIPTION
Key unit [R-320CK]
Key unit [R-330CK]
Key unit [R-320CW]
Key unit [R-330CW]
Key unit [R-320CD]
Open button [R-320CK]
Open button [R-330CK]
Open button [R-320CW]
Open button [R-330CW]
Open button [R-320CD]
Open button spring
LED sheet [R-320CD]
LED sheet [R-320CK]
LED sheet [R-320CW]
LED sheet [R-330CK]
LED sheet [R-330CW]
LCD holder [R-330CK]
LCD holder [R-330CW]
LCD holder [R-320CD]
LCD holder [R-320CK]
LCD holder [R-320CW]
Screw; 3mm x 8mm
Q'TY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
CODE
AY
AY
AY
AY
AY
AF
AF
AF
AF
AF
AB
AE
AE
AE
AK
AK
AL
AL
AK
AK
AK
AA
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AU
AF
AQ
AD
AL
BA
-AX
AH
AG
AG
AH
AC
AE
AG
AF
AU
AF
AF
AC
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
5
1
BD
AH
AY
AY
AY
AY
AY
AX
AY
AY
AZ
AZ
AG
AC
AA
AB
AS
1
1
1
1
1
1
1
AQ
AR
AU
AF
AB
AC
AB
OVEN PARTS
∆
∆
4- 1
4- 2
4- 3
4- 4
4- 5
4- 6
4- 7
4- 8
4- 9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
4-18
4-19
4-20
PDUC-A724WRF0
PPACGA084WRF0
PHOK-A114WRF0
LBNDKA099WRW0
NFANJA029WRE0
PDUC-A725WRP0
*************
LANGFA192WRP0
PCUSGA321WRP0
PCUSUA270WRP0
MLEVPA233WRF0
NCPL-A045WRF0
PCUSUA511WRP0
PCOVPA349WRE0
PCUSGA339WRP0
PCUSGA399WRE0
LANGTA360WRP0
PCUSUA167WRP0
PCUSUA524WRP0
PCUSUA126WRE0
Air separater
TTM packing
Latch hook
Capacitor holder
Fan blade
Fan duct
Oven cavity (Not a replaceable part)
Chassis support
Cushion
Cushion
Switch lever
Coupling
Cushion
Waveguide cover
Cushion
Cushion
Sensor mounting angle
Cushion
Cushion
Cushion
55555555555555555-
1
2
3
3
3
3
3
4
4
4
4
4
5
6
7
8
9
FDORFA332WRT0
PSHEPA382WRE0
GWAKPA626WRR0
GWAKPA615WRR0
GWAKPA615WRR0
GWAKPA617WRR0
GWAKPA617WRR0
HPNL-A720WRR0
HPNL-A717WRR0
HPNL-A717WRR0
HPNL-A719WRR0
HPNL-A719WRR0
LSTPPA188WRF0
MSPRTA187WRE0
XCPSD40P08000
PCUSUA504WRP0
GCOVHA405WRF0
Door panel
Sealer film
Door frame [R-320CD]
Door frame [R-320CK]
Door frame [R-330CK]
Door frame [R-320CW]
Door frame [R-330CW]
Door screen [R-320CD]
Door screen [R-320CK]
Door screen [R-330CK]
Door screen [R-320CW]
Door screen [R-330CW]
Latch head
Latch spring
Screw : 4mm x 8mm
Cushion
Choke cover
6666666-
1
2
3
4
5
6
7
FROLPA079WRK0
NTNT-A079WRE0
FW-VZB723WRE0
QW-QZA150WRE0
PZET-A012WRE0
TCAUAA166WRR0
TCAUAA200WRR0
Turntable support
Turntable tray
Main wire harness
High voltage wire B
Terminal insulator
DHHS caution label
Monitor caution label
DOOR PARTS
∆
∆
∆
∆
∆
∆
∆
MISCELLANEOUS
*
42
R-320CD/CK/CW
R-330CK/CW
REF. NO.
6- 8
6- 8
6- 8
6- 8
6- 8
6- 9
6-10
6-10
PART NO.
TINSEA792WRR0
TINSEA792WRR0
TINSEA792WRR0
TINSEA793WRR0
TINSEA793WRR0
TCAUAA240WRR0
TCADCA685WRR0
TCADCA685WRR0
DESCRIPTION
Instruction book [R-320CD]
Instruction book [R-320CK]
Instruction book [R-320CW]
Instruction book [R-330CK]
Instruction book [R-330CW]
Screw caution
Recipe sheet [R-330CK]
Recipe sheet [R-330CW]
777777777777-
XHPSD40P08K00
XHPSD30P06000
XHTSD40P08RV0
XHTSD40P12RV0
XOTSD40P12RV0
XOTSD40P12000
XOTSF40P08000
XOTSF40P08000
XOTSE40P08000
XOTSE40P08000
XOTSE40P08000
LX-CZA070WRE0
Screw :
Screw :
Screw :
Screw :
Screw :
Screw :
Screw :
Screw :
Screw :
Screw :
Screw :
Special
Q'TY
1
1
1
1
1
1
1
1
CODE
AE
AE
AE
AK
AK
AC
AE
AE
SCREWS,NUTS AND WASHERS
1
2
3
4
5
6
7
7
7
7
7
8
4mm x
3mm x
4mm x
4mm x
4mm x
4mm x
4mm x
4mm x
4mm x
4mm x
4mm x
screw
8mm
6mm
8mm
12mm
12mm
12mm
8mm [R-320CK]
8mm [R-330CK]
8mm [R-320CD]
8mm [R-320CW]
8mm [R-330CW]
(Torx tamper proof screw)
9
3
2
1
6
15
1
1
1
1
1
2
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER
3. PART NO.
2. REF. NO.
4. DESCRIPTION
Order Parts from the authorized SHARP parts Distributor for your area.
Defective parts requiring return should be returned as indicated in the Service Policy.
PACKING AND ACCESSORIES
TOP PAD ASSEMBLY
FPADBA395WRK0
DOOR PROTECTION SHEET
SPADPA204WRE0
PLASTIC BAG
SSAKHA034WRE0
6- 8
INSTRUCTION BOOK
& PRINTING MATTER
6-10 RECIPE SHEET
(for R-330CK/CW)
6- 2
TURNTABLE TRAY
BOTTOM PAD ASSEMBLY
6- 1 TURNTABLE SUPPORT
FPADBA396WRK0
TRAY PACK
INTO THE
OVEN CAVITY
SPADFA451WRE0
Not replaceable items.
43
PACKING CASE
SPAKCD233WRE0 [R-320CD]
SPAKCD205WRE0 [R-320CK]
SPAKCD207WRE0 [R-320CW]
SPAKCD206WRE0 [R-330CK]
SPAKCD208WRE0 [R-330CW]
R-320CD/CK/CW
R-330CK/CW
2
1
4
3
6
5
OVEN AND CABINET PARTS
7-5
4-18
2-1
4-13
7-8
A
A
4-17
7-5
1-15
4-10
6-7
7-1
B
B
7-2
7-8
1-10
1-11
4-19
6-6
1-4
1-8
7-7
7-5
C
C
7-6
7-3
6-9
1-5
D
D
7-4
4-7
4-20
7-1
4-12
4-3
4-15
1-7
1-13
1-1
7-5
E
E
4-14
1-2
6-2
4-4
4-2
4-11
4-8
7-6
1-3
1-12
7-3
4-5
1-1
F
7-6
7-2
1-6
7-1
6-1
4-9
7-5
7-6
F
7-1
4-1
1-14
2-2
4-6
4-16
2-4
1-9
G
G
7-6
2-3
7-6
H
H
7-6
7-6
7-6
2-3
1
2
4
3
44
5
6
R-320CD/CK/CW
R-330CK/CW
2
1
4
3
6
5
3-8
CONTROL PANEL PARTS
3-2
3-8
A
A
3-2
3-7
3-6
3-7
3-3
3-6
3-8
B
B
3-8
3-1
3-3-1
3-1
3-3
C
3-3-1
3-4
C
3-4
3-5
R-330CK/CW
R-320CD/CK/CW
3-5
D
D
5-9
5-7
DOOR PARTS
5-2
5-7
5-1
E
E
5-8
5-7
5-3
F
5-7
5-4
5-8
F
5-8
5-8
5-5
G
G
5-6
MISCELLANEOUS
6-3
(CAPACITOR)
6-4
H
H
6-5
Actual wire harness may be different from illustration.
1
2
4
3
45
5
6
R-320CD/CK/CW
R-330CK/CW
COPYRIGHT © 1999 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in retrieval systems, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
'99 SHARP CORP. (2S2.530E) Printed in U.S.A
46