ACI Farfisa Single Channel DVR User manual

User Manual
User Manual
Contents
SAFETY INSTRUCTION ........................................................................................................................................................... 1
CHAPTER 1: DVR FEATURES................................................................................................................................................ 2
CHAPTER 2: LAYOUT .............................................................................................................................................................. 3
2.1 DVR FRONT PANEL .............................................................................................................................................................. 3
2.1.1
4-CH DVR Front Panel...................................................................................................................................... 3
2.1.2 8-CH DVR Front Panel ............................................................................................................................................ 4
2.2 REAR PANEL ......................................................................................................................................................................... 5
2.2.1 4-CH DVR Rear Panel ............................................................................................................................................. 5
2.2.2
8-CH DVR Rear Panel ...................................................................................................................................... 5
2.3 REMOTE CONTROLLER ......................................................................................................................................................... 6
CHAPTER 3 DVR INSTALLATION ......................................................................................................................................... 7
3.1 HDD INSTALLATION............................................................................................................................................................. 7
3.2 CAMERA AND MONITOR CONNECTION ............................................................................................................................... 7
3.3 POWER SUPPLY CONNECTION ............................................................................................................................................. 7
CHAPTER 4: DVR START UP ................................................................................................................................................. 8
4.1 SYSTEM INITIALIZATION ....................................................................................................................................................... 8
4.2 LIVE SCREEN ........................................................................................................................................................................ 8
CHAPTER 5: DVR MENU ......................................................................................................................................................... 8
5.1 POP-UP MENU....................................................................................................................................................................... 8
5.2 MAIN MENU GUIDE .............................................................................................................................................................. 9
5.3 MAIN MENU ....................................................................................................................................................................... 10
5.3.1 Display setup............................................................................................................................................................ 10
5.3.2 Record setup ............................................................................................................................................................ 10
5.3.3 Network Setup.......................................................................................................................................................... 11
5.3.4 Record Search ........................................................................................................................................................ 13
5.3.5 Playback Player ...................................................................................................................................................... 14
5.3.6 Device Management ............................................................................................................................................... 16
5.3.6.1 HDD Management...................................................................................................................................................................16
5.3.6.2 Alarm Setup .............................................................................................................................................................................17
5.3.6.3 PTZ setup.................................................................................................................................................................................19
5.3.6.4 Mobile......................................................................................................................................................................................19
Mobile Viewer’s Access Instruction ....................................................................................................................................................20
5.3.6.5 Motion Detect Setup ................................................................................................................................................................27
5.2.7 System3 ................................................................................................................................................................... 27
5.3.7.1 Time Setting.............................................................................................................................................................................27
5.3.7.2 Password..................................................................................................................................................................................27
5.3.7.3 Video/Audio Setup...................................................................................................................................................................28
5.3.7.4 Language .................................................................................................................................................................................28
5.3.7.5 System Information..................................................................................................................................................................28
5.3.7.6 Maintain...................................................................................................................................................................................29
5.4 MENU LOCK ....................................................................................................................................................................... 29
User Manual
5.5 RECORD SEARCH ................................................................................................................................................................ 30
5.6 PTZ CONTROL ................................................................................................................................................................... 30
5.7 RECORD ............................................................................................................................................................................. 30
5.8 STOP RECORD ..................................................................................................................................................................... 30
CHAPTER 6: WEB APPLICATION MANAGER......................................ERRORE. IL SEGNALIBRO NON È DEFINITO.
6.1 PLUG-INS DOWNLOAD AND INSTALLATION ....................................................... ERRORE. IL SEGNALIBRO NON È DEFINITO.
6.2 WEB CLIENT LOG-IN ........................................................................................ ERRORE. IL SEGNALIBRO NON È DEFINITO.
6.3 WEB CLIENT INTERFACE .................................................................................. ERRORE. IL SEGNALIBRO NON È DEFINITO.
6.3.1 Menu Bar............................................................................................................Errore. Il segnalibro non è definito.
6.3.1.1 Live Display .................................................................................................................... Errore. Il segnalibro non è definito.
6.3.1.2 Playback........................................................................................................................... Errore. Il segnalibro non è definito.
6.3.1.3 Remote Setting................................................................................................................. Errore. Il segnalibro non è definito.
6.3.1.4 Local setting .................................................................................................................... Errore. Il segnalibro non è definito.
6.3.1.5 Logout.............................................................................................................................. Errore. Il segnalibro non è definito.
6.3.2 PTZ Control .......................................................................................................Errore. Il segnalibro non è definito.
6.3.3 Play Control .......................................................................................................Errore. Il segnalibro non è definito.
CHAPTER 7: SPECIFICATIONS ........................................................................................................................................... 41
CHAPTER 8: APPENDIX ........................................................................................................................................................ 42
8.1 RECORD ALARM SETTING ................................................................................................................................................... 42
8.2 SUSTAINABLE RECORD TIME LIST ...................................................................................................................................... 42
8.3 MAIL BOX SERVER LIST ...................................................................................................................................................... 42
8.4 TROUBLESHOOTING ............................................................................................................................................................ 43
8.5 SYSTEM CONFIGURATION ................................................................................................................................................... 44
8.6 ACCESSORIES ..................................................................................................................................................................... 45
User Manual
Safety Instruction
1. Read Instruction
All the safety and operating instruction should be read before the equipment is operated.
2. Power sources
This equipment should be operated only from the type of power source indicated on the marking label. If
you are not sure of the type of power, please consult your equipment dealer.
3. Objects and Liquid
Never push objects of any kind through openings of this equipment and / or spill liquid of any kind on the
equipment as they may touch dangerous voltage points or short out parts that could result in a fire or electric
shock.
4. Water and / or Moisture
Do not use this equipment near water or in contact with water.
5. Heat sources
Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including
amplifier) that produce heat.
6. Cleaning
Unplug this equipment from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a
damp soft cloth for cleaning.
7. Lightning
Unplug this equipment during lightning storm or when unused for long periods of time.
8. Accessories
Do not place this equipment on an unstable cart, stand or table. When a cart is used, use caution when
moving the cart / apparatus combination to avoid injury from tip-over.
9. Moving
Disconnect the power before moving the equipment. And the equipment should be moved with care.
10. Attachment
Never add any attachments and/or equipment without the approval of the manufacturer as such additions
may result in the risk of fire, electric shock and other personal injury.
11. Correct Batteries
Risk of explosion occurs if battery is replaced by an incorrect type. Therefore you must use the same type
of battery as the one being used in the product.
12. Ventilation.
Do not block any ventilation openings, installation of the equipment in the rack should be such that the
amount of airflow required for safe operation of the equipment is not compromised.
13. Overloading
Do not overload wall outlets and extension cords to avoid the risk of fire or electric shock.
14. Reliable Earthlings (Grounding)
Reliable grounding of rack mounted equipment should be maintained. Particular attention should be given to
supply connections other than direct connections to the branch circuit.
1
User Manual
Chapter 1: DVR Features
Function
Brief and Description
Real-time Monitoring
Double video output, with Monitor or VGA virtual output, support Net-viewer and
Mobile Live monitor, and also support zoom in/out, auto sequence and PIP display.
Record Function
H.264 video compression format; record quality adjustable, multiple recording
modes (Always, Scheduled, Manual, Alarm, Motion detection and remote record)
Record storage
Playback
Support SATA large capacity HDD and save real-time record image to HDD.
Support DVR single CH and multiple CH Search/Playback of recorded files.
Backup
Support DVR backup via USB flash drive, removable drive, Recorder and
network.
Alarm Setting
Supports HDD & video input alarm management and external alarm signal
inputs.
Network operation
Supports remote surveillance by authority users to increase system security.
Mouse Operation
Supports Mouse operation for faster menu navigation.
PTZ Control
Supports PTZ camera operations through RS-485.
List 1-1
Other Features:
H. 264 video compression format; supports D1, HD1 and CIF resolutions;
ADPCM audio compression format;
Windows Graphical interface; embedded real-time Linux 2.6 operation system;
Multiple operations (Live, record, playback, backup, network surveillance and mobile phone monitoring
simultaneously);
Supports Double Encode bit network transmission;
Supports remote live viewing via 3G mobile network;
The video package time is adjustable;
Friendly Menu reminder;
Multiple alarm record mode
Rear USB2.0 ports for back-up, upgrade and mouse operation;
With IR remote control;
Multiple language OSD;
Supports auto maintenance
2
User Manual
Chapter 2: Layout
2.1 DVR Front Panel
DVR is a short form of Digital Video Recorder.
2.1.1 4-CH DVR Front Panel
Item
Key title
or Indicator
1
Power button
2
Power Indicator
3
IR Receiver
4
HDD Indicator
Remark
Function & Description
Power on/off
If the “Green” indicator is on the system is getting power
PWR
normally.
Receives IR signal from Remote Controller
When the “Red” indicator flashes it means the hard drive is
HDD
being read or written to.
CH select Key:
5
CH1
CH2
CH3
CH4
6
QUAD
7
CH select key
On Live display or Playback mode, switch to Quad
display.
REW
Left direction key, Rewind key;
Pressing the key to decrease PTZ rotation speed and
parameter value.
8
PAUSE
Pause / play frame by frame manually
9
PLAY
Enter into [Record Search] Menu; Play record file.
10
FWD
Right direction key, Forward key;
Pressing the key to increase PTZ rotation speed and
Parameter value.
11
STOP
Stop Playing and/or manual recording.
12
REC
●
Start manual record
13
MENU/ESC
Enter into Main menu or Exit
14
Up key
Move to up
15
SEL/EDIT
Enter into pop-up menu; Select or Enter menu;
Edit menu.
16
Down key
Move to down
17
PTZ:
Enter into pop-up menu.
List 2-1
3
User Manual
2.1.2 8-CH DVR Front Panel
pp.jpg
Item
Key title or Indicator
Remark
Function & Description
1
Power button
Power on/off
2
Power Indicator
3
IR Receiver
4
HDD Indicator
5
SEARCH
Record search
6
MUTE
Mute on/off
7
CH-
Switch to previous channel
8
CH+
Switch to next channel
9
QUAD
On live mode, clicking the button will switch to
Quad display.
10
REW
Move to left;
Rewind playing at multiple speeds;
Decrease parameter value of image setting.
11
PAUSE
Pause/play frame by frame manually
12
PLAY
Enter into pop up menu; Play recording file
PWR
If the “Green” indicator is on the system is getting power
normally.
Receives IR signal from Remote Controller
HDD
When the “Red” indicator flashes it means the hard drive is
being read or written to.
13
FWD
Move to right;
Forward playing at multiple speeds;
Increase parameter value of image setting
14
STOP
Stop playing; Stop manual record
15
REC
●
Start manual record
16
Enter into Main menu/Exit
17
MENU/ESC
Up direction key
Move to up
18
SEL/EDIT
Enter into pop-up menu;
Confirm the selected operation
Enter into [Edit] function
Move to down
19
Down direction key
20
PTZ:
Enter into pop up menu.
List 2-3
4
User Manual
2.2 Rear Panel
2.2.1 4-CH DVR Rear Panel
15.jpg
2.2.2 8-CH DVR Rear Panel
125.jpg
Item
Physical port
Connection method
1
Video input
Connect CH1-8 (Virtual) video input device(BNC interface)
2
Video output
Connect monitor output (BNC interface)
3
Audio I/O
4CH DVR: 4CH audio input and 2CH output;
8CH DVR: 8CH audio input and 1CH output. (RCA interface)
4
Ethernet: Port
Connect LAN, Ethernet (RJ45 interface)
5
VGA Port
Connect to VGA monitor, such as PC monitor (Optional)
6
USB Port
Connect USB device (Flash Drive, Hard Drive and Recorder etc)
7
USB Port
Connect USB mouse
8
RS-485/Sensor/Alarm
RS485/Sensor/Alarm interface (see pin outs below)
9
Power Port
Connect power supply - DC12V 3A/5A
List 2-3
4-CH: RS485/Sensor/Alarm port functions (from
8-CH: RS485/Sensor/Alarm port functions (from left to right):
left to right):
Pin 1-2:PTZ Control port (Pin 1:RS-485A / Pin 2:RS-485B)
Pin 1-2:PTZ Control port (Pin 1:RS-485A / Pin 2:
Pin 3-4:Connect external sensor 1 input
RS-485B)
Pin 4-5:Connect external sensor 2 input
Pin 3-4:Connect external sensor 1 input
Pin 6-7:Connect external sensor 3 input
Pin 5-6:Connect external sensor 2 input
Pin 7-8:Connect external sensor 4 input
Pin 7-8:Connect external sensor 3 input
Pin 9-10:Connect external sensor 5 input
Pin 9-10:Connect external sensor 4 input
Pin 10-11:Connect external sensor 6 input
Pin 11-12:Connect external sensor output
Pin 12-13:Connect external sensor 7 input
Pin 13-14:Connect external sensor 8 input
Pin 15-16:Connect external sensor output
5
User Manual
2.3 Remote Controller
e
Key title
1
1-8
2
9、0
Numeric key
3
ALL
Multiple display mode
4
Menu
5
▲
Up direction key, Volume adjust
6
▼
Down direction key, Volume adjust
7
8
Channel select 1-8; Numeric key
Enter into Main menu/Exit
◄/
Left/Down
direction
key,Decrease/increase
parameter value of control bar
SEL
Select key/Edit key;Confirm the selected operation.
9
Rewind key
10
Enter into record search menu;Play key
11
Forward key
12
●
Record key
Pause/Sequence key
13
Mouse Operation
Key function
14
■
15
Audio
No function for this particular model
16
Mute
Mute function
List2-4
Stop manual record; stop playing
Except using buttons of front panel or remote controller, you also can use mouse to perform system
operation.
TYPE
Function
In menu lock mode, Enter into pop-up menu and clicking any sub menu to pop up Log-in
window; on menu unlock mode, enter into pop-up menu, and then clicking left key to
enter into any sub menu directly.
Click left key of
Mouse
Click right key of
Mouse
Double-click Left
key of Mouse
Moving Mouse
Sliding Mouse
After entering into main menu, clicking left key could enter into any sub menu; On
[Detailed file] menu mode, clicking left key could playback one recording file.
Change the status of check box and motion detection area.
Clicking combo box to access pull-down menu; Click left key to stop dwell time display
when dwell time display is activated.
By clicking left key you can adjust Color control bar and volume control bar.
Clicking combo box to access pull-down menu
By clicking left key you can select values in edit boxes or pull-down menu and supports
Chinese word input, special symbol, numeric and character input, use instead of
[Enter] or [Backspace
]
In live display mode, clicking right key will display pop-up menu (shown as Picture 5-1).
In Main menu or sub menu mode, clicking right key will exit current menu.
In live display or playback mode, double-clicking left key will maximize the screen.
Select menu item
On motion mode, sliding mouse will select motion area; On [Color set] menu mode,
sliding mouse will adjust color control bar and volume control bar.
List2-5
6
User Manual
Chapter 3 DVR INSTALLATION
3.1 HDD Installation
Caution:
1. Please do not Install or take out hard drive when DVR is running!
2. Some model has a HDD drawer. Please use provided key to take out the HDD drawer and put HDD
into the drawer correctly.
HDD Installation:
After cutting power, remove screws on two sides of body and on rear panel and open DVR
upper cover carefully;
Connect data cable and power cord of HDD to main board securely shown as Picture 3-1.
Picture3-1
Picture 3-2
Fix the HDD back body shown as Picture 3-2;
Put the upper cover back carefully, re-attach screws.
Note: If users need higher performance HDD, strongly recommend to use special HDD for Security
Protection.
3.2 Camera and Monitor Connection
Connect camera cable to video input of DVR, and from video output of DVR to Monitor via BNC
connector (Refer to section2.2-Rear Panel); or
If the camera is a PTZ speed dome, you could connect RS485 A & B to the according port of DVR
respectively (refer to system figuration on Chapter 8).
3.3 Power Supply connection
Please only use the power adapter supplied with the DVR.
After power on please make sure the video I/O connection well and select microphone and audio device
with RCA cable.
7
User Manual
Chapter 4: DVR Start up
4.1 System Initialization
After connecting the Power cable of DVR to wall outlet and pressing the
Power button on the front panel, you will enter into the system initializing
screen shown as Picture 4-1.
Picture
4.2 Live screen
After finishing initialization the system will enter into Live screen
Picture 4-2 is the 9-split display defaulted by system, which is showing
no video input status. Once there are video inputs, the screen wil
display live images from the cameras. In Live mode, if you use the
mouse to double-click the live image of any channel, the image will be
maximized to full screen, by double-clicking again, image will be come
back to 4-split or 9-split display mode; clicking the right button of the
mouse will enter into Pop-up Menu; clicking the left button of the mouse
allows you select menu items; and clicking any area outside the menu
allows you exit the Pop-up menu.
Picture 4-2
Note: When internal HDD is not connected or an error occurs, the character “H” will appear on the first
channel of the live screen and accompany buzzer alarm. If you want to close the buzzer alarm, please enter
into [Device manage Alarm setting] to set HDD loss, HDD space not enough and alarm output to “off”.
Chapter 5: DVR Menu
5.1 Pop-up Menu
Picture5-1a
Picture5-1b
Picture5-1c
After finishing system initialization, click right key of mouse on Live mode to enter into Pop-up Menu.
Now you could perform parameter setting and operate on Main Menu, Multi-Pics, PTZ, PIP, Rec. Search,
Mute, Manual record, Start Rotate, Start Cruise and UI to VGA etc.
Note: options of the Pop-up menu will differ depending on different parameter setting and application
environment.
8
User Manual
5.2 Main Menu Guide
Title Set
Camera
Color set
Display Set
Record Resolution
Record
Record Scheduled
Static set
DHCP set
Network
PPPoE set
DDNS set
Search/Playback
Main Menu
Search
File List
File Backup
Log Search
Log Export
HDD
Alarm
Device Manage
Email Set
PTZ set
Mobile
Motion
Area Set
Time
Password
Volume
Audio/Video
Margin
System function
Language
System Info
System Maintain
9
Back to Factory Set
User Manual
5.3 Main Menu
After clicking right button of mouse, pop-up menu appears on
he screen. You can click [main menu] option on pop-up menu mode
o enter into Main menu interface (Shown as Picture 5-2). In Main
Menu mode, you can control device management settings, such as
isplay, Record, Network, Search, Device and System setting etc.
Picture 5-2
5.3.1 Display setup
Go to [Main menu Camera] to set up the CH name and position for each channel shown as Picture 5-3.
You can set up whether each channel can be previewed or not
under Live display and/or record mode, enable live time or not under
live screen and set up record time or not on the record history.
Please note that the name of each channel supports up to eight
characters or four Chinese characters.
Copy function: allow you copy all data of one channel to any
other channel.
Picture 5-3
You can adjust image brightness, saturation, contrast
and hue parameters of each channel after entering into
[Color] menu.(shown as picture 5-4).
Picture 5-4
Explanation:
1、 The modifications will be available after clicking [APPLY]
button on the bottom of the sub-menu windows and being
prompted to save and then clicking [ok] button.
2、 If you want to cancel the modification, click [Exit] button to exit
the menu.
Picture 5-5
3、 When clicking [DEFAULT] button, all system default values will
be reset to default value.
5.3.2 Record setup
Click [Main Menu]
[Record] to enter into [Record Setup] menu (Shown as Picture 5-5).
[Record] option allows you set up record status (Enable/Disable) of each channel.
[Bit rate] include three options – Best, Good and Normal.
10
User Manual
[Frame rate] include two options – Fixed and Manual. When set
to “Manual” and click [Frame rate setup] option, you may
allocate the frame rate for each channel.
Picture 5-6
[Audio] option allows you turn audio on/off.
[Mode] allow you select record modes, including Always and
Scheduled. To record 24 hours a day set the [Mode] to Always.
To record on motion or a set schedule, select the [Schedule]
option.
[Pack time] indicates maximum continuous record time (15, 30, 45 and 60 min).
[Pack time] allow you copy current settings to any other channel.
When setting [Mode] to Schedule, the schedule screen will appear as shown in Picture 5-6.
[Record CH] options include All, CH-1, CH-2, CH-3, CH-4,
CH-5…CH-16 in turn. Please click the channel you need.
To setup weekly schedules, tick-select the box of the record
status you want (Alarm, General, or No Record) and then click on
each box in the schedule time line that you want this method to apply
to. You can use the [From – To] pull-down menus and Copy button to
copy settings from one day to another day or all days.
Picture 5-7
After you complete the schedule you activate it by clicking the [Apply] button.
You can also click the [Default] button to use the system defaults.
Explanation: On the [record] Set and [Search] mode, original color stands for no record, “Red” stands
for alarm record and “Green” stands for normal record
5.3.3 Network Setup
Enter into [Main Menu Network Setup] to setup the network configuration (Shown as picture 5-7):
After selecting network mode - such as DHCP, PPPOE or static allocation- and setting up web ports,you
can visit DVR remotely through a network or internet.
DNS: DNS server is generally provided by local ISP. Herein please enter the IP address of your DNS.
When selecting DHCP the router will allocate DVR IP address
automatically after you exit the menu. The IP address of the DVR
might change whenever the unit is turn on.
Picture 5-8
Picture 5-8
Picture 5-9
When selecting Static from the Type, user can directly set IP
address, Subnet Mask, Gateway, Web Port and DNS shown as
Picture 5-9.
11
User Manual
When selecting PPPoE form the Type, user can input user name
and password provided by ISP and set Media and Web port
(details please refer to the Picture 5-10). You can visit your DVR
via public network without port forwarding when network type is
set to “PPPoE” and web port is right.
Picture 5-10
DDNS (Dynamic DNS) is a service that register a domain name and the floating IP address with the
DDNS server so that the domain name can be routed to the IP address even if the IP address is changed in a
dynamic IP system.
At the bottom of the NETWORK SETUP window there is an
option to setup the DVR to be accessed through a DDNS service.
When you click on the DDNS button it brings up the window
displayed as Picture 5-11. You can access the DVR through a static
or dynamic IP address; however a dynamic address can change
from time to time. How often depends on your service provider When
it changes you need to go to a website such as
www.myipaddress.com from a computer attached to the same router
as the DVR to find out what the new IP address is.
Picture 5-11
Server: select a Dynamic domain name server provided by ISP;
Host Name: Input host name registered from Dynamic Domain Naming System, for example:
DVR2009.3322.org;
User Name: Input a user name registered before applying for a domain name;
Password: Input a password you set when registering a user name.
Router’s Port Forwarding
Picture 5-12
Port forwarding is required when you want to access the
DVR connected to the router from outside of the router’s
network.
1. Input router’s IP address from IE-based browser to open
the Router configuration interface;
2. Click [Transmittal rule] option to take you to the port
forwarding instructions for your router;
3. Set the corresponding parameters illustrated in Picture
5-11. When server port and web port forwarding the DVR IP
address, user can visit the DVR remotely.
4. User can enter below website or domain name as per current PC network environment to visit the
remote DVR.
1. http://public IP: Web port(such as 0080)
2. http://intranet IP: Web port(such as 0080)(only available at the same LAN)
3.http://superdvr.3322.org: Web port(such as 0080)
Friendly Reminder: The router’s port forwarding interface may be different, however, when entering
into virtual server, user will always need forward port 8080 and port 9000 of router to IP address of DVR
allocated or automatically captured, and select [All] or [Both] in corresponding protocol column and save the
12
User Manual
above setting.
Above steps may differ from the router device depending on the manufacturer.
5.3.4 Record Search
Click [Main Menu Record Search] to enter into below window shown as Picture 5-13.
Channel: allows you select the channel(s) you desire to search.
Time Search: In the Video Search screen, user can search for a
specific date and time for a recording and view it in Playback mode.
This is useful for hunting a specific recording of an incident if you
know the date and time it occurred.
Date Search: In the Video Search screen, user can search for all
the recordings in a specific date. To execute a video search, highlight
and select the date numeric field,and then click a detailed time
Picture 5-13
quantum of the specific date, system will start the playback from the first recoding of the time quantum.
Playback Mode: You can use the Playback Control bar to operate the Fast Forward (X2, X4 and X8),
Slow play (1/2, 1/4 and 1/8 speed), Play, Pause/Frame, Rewind(X2, X4 and X8). When ending playback,
DVR will return back to previous menu.
File List: click [File list] button to enter into the [File List] screen shown as Picture 5-14, the video
recordings for the time quantum will appear in the screen. And you also can filter the recordings you want to
view by the Channel or recording mode based on date/time search.
First:Indicates the first page of recording history you have
searched. When you view other pages, clicking [First] button brings
you back to Page one.
PREV (Previous page): When viewing event list, clicking
[Previous page] button will take you back to page before the one
you are currently viewing (except the first page).
NEXT (Next page): When viewing event list, clicking [Next
page] button will take you to the page after the one you are currently
viewing (except the last page).
Picture 5-14
LAST (Last page): Indicates the last page of recording history you have searched. When you view other
pages, clicking [Last page] button will take you to the Last page.
ALL (Select All): Allows you to select all the events on the current page.
INVERSE (Select Invert): Allows you to select other events on the current page except those you have
currently selected.
Back up: In the [File List] mode, if you wish to backup records, please tick-select the [Select] check-boxes
which corresponds to the recording and click [Backup] button to enter into the below windows illustrated in Picture
5-15. When backup processing ends, system will prompt you “Backup finished!” shown as Picture 5-16.
Picture 5-15
13
Picture 5-16
User Manual
Note:
1. Backup file will be saved as H264 format; you can playback the recorded files using the Multimedia
Player program that comes with the DVR or through the net-viewer program.
2. Please make sure you have connected backup device, such as USB and DVD, well before
backing-up.
Log Search
In the Record Search screen, Click [Log Search] to pop up the Log search screen shown as Picture 5-17(a).
Select log type, enter start date & end date, and then click the [Search] button on the bottom of the
interface to search all the logs you need shown as Picture 5-17(b).
Picture 5-17(a)
Picture 5-17(b)
Export
User can export all the logs which have been searched to U flash disk and save it as TXT format.
Before exporting the logs, please make sure you have connected the U flash disk well. Detail operations please
refer to Picture 5-18.
After Log export success, please click [OK] button shown as Picture 5-19.
Picture 5-19
Picture 5-18
5.3.5 Playback Player
1. Copy backup file to your PC;
2. Open Playback Player, and then click [+] button to open the file shown as Picture 5-20
Picture 5-20
14
User Manual
3. Select the playback file you desired from the file shown as Picture 5-21.
Picture 5-21
Note: Please select the file with *.264 format or *.nvr. The record file backed-up by U flash disk or removable
disk is with *.264 format, and DVD Recorder with *.nvr format.
4. Open backup file
Double-click the record event at the right side of screen to start record file playback.
Picture 5-22
The button functions from left to right in turn are as follows:
[Play] button: start playing record file
[Pause] button: pause the record file playback
[Stop] button: stop the record file playback
[Rewind] button: rewind playing the record file at X2, X4, X8 and X16 speeds.
15
User Manual
[Forward] button: forward playing the record file at X2, X4, X8 and X16 speeds.
[Frame by frame]: Play the record file frame by frame.
[Snapshot]: click the button to capture the record image and save the image to a specified position.
[Add]: click the button to add one record file
[Del]: click the button to delete one record file.
[Del all]: click the button to delete all the record files in the event list.
5.3.6 Device Management
Options in device management include HDD, Alarm, PTZ, Mobile,
Motion and Serial set.
Click [Main Menu Device Management] option to enter into the
window shown as Picture 5-23.
Picture 5-23
5.3.6.1 HDD Management
In the [Device Management] screen, highlight and click [HDD] icon to
enter into the window shown as Picture 5-24.
Picture 5-24
When DVR is connected to a HDD, the system will
automatically detect if HDD is normal or not;
If the cable connected to HDD is loosen or HDD is abnormal, HDD
status will be shown as “No Disk”, or,
If HDD need to be formatted, status will be shown as “no format”,
otherwise, the HDD status will be shown as “Normal” (refer to
Picture 5-25).
NO:HDD number defaulted by system
Picture 5-25
State:Available Hard drive. You could use HDD only when formatting the HDD and inspect its status normal.
TOTAL/AVAIL: Indicates total space available on Hard Drive. / Unused space available on the Hard Drive.
AVAIL TIME: Based on current image detail/quality and frame rate, system will show you how many
record time you have left on the Hard Drive.
OVERWRITE: If you select “on” the system will automatically overwrite the oldest recordings once the
hard drive is full; if you select “off”, recording will stop once the hard drive is full.
HDD FORMAT: You use this option to format the hard drive, you can not record files to the hard drive until
it has been formatted. Click [Format HDD] button to start formatting. When selecting [Format HDD] option
the system will prompt you – “Format HDD will loss all the data, do you confirm?” ; click “OK”, system will
prompt you – “Is formatting…” and “successful format”; and then system will restart automatically.
16
User Manual
USB FORMAT: Use this option to format USB devices.
Note: It is an important first step when configuring your DVR to make sure that the hard drive (HDD)
options are correctly set. So, it is strongly recommended that you do format the HDD before start the first record.
5.3.6.2 Alarm Setup
Click [Main Menu Device Alarm] to enter into the below window shown as Picture 5-26 (a).
Picture 5-26 a
Picture 5-26 b
Click [Alarm Config] on the bottom of the [Alarm setup] screen to enter into the interface shown as
Picture 5-26(b).Now you are allowed to set detailed alarm parameters.
Channel: the option allows you select one channel you want.
I/O Status: allows you select the three options – NO (Normal Open), NC (Normal Close) and OFF. Set
to “Normal Open”, I/O status Alarm will be activated while sensor is ON; set to “Normal Close”, I/O status
alarm will be activated while sensor is OFF; set to “OFF”, I/O status alarm will not be triggered.
HDD Loss: When setting [Buzzer] to ON and there be no HDD detected or the HDD is not formatted, a
small “H” appears on the screen with buzzer sound. Setting this to OFF will only show the “H” on the
screen but the buzzer will not sound.
HDD Space: When setting [Buzzer] to ON and the DVR is running out of storage space the buzzer will
sound. No alarm will sound if it is set to OFF.
Video Loss: When setting [Buzzer] to ON and when a camera has been disconnected. “Video Loss”
icon will also appear on the screen with buzzer sound. Set to OFF, you will only see the “Video Loss”
appear but no sound
Alarm Manage:Alarm Output: you can set how long the external sensor alarm will last when motion is
detected (off, 10s, 20s, 40s, 60s);
Buzzer time: you can set how long the buzzer will sound when motion is detected (0s, 10s, 20, 40s, 60s);
Alarm duration time: you can set how long alarm record will last when alarm ends (0s, 30s, 1minute,
2minute,5minute);
Pre-record time: you can set how long record will last before alarm occurs (Off, on).
Full screen Alarm: The function is defaulted to “On". When the motion detection or external alarm is
triggered, the corresponding channel will be displayed on the full screen mode.
Email:The option allows you set the alarm images is issued to a specified email or not.
You could freely select buzzer alarm or not and alarm output time for all the alarm types, and for the MD
alarm and I/O status alarm you could set email and full screen reminder.
Alarm Type
Video Loss
Motion Detection
Function
Sends alarm when DVR can’t receive video signal (such as camera damage, cable broken or damaged
or power supply malfunction).
When an object moves into motion detection area, alarm will be triggered. You can adjust sensitivity
level to suit the needs of your actual application environment.
I/O Status
System can convert alarm signal triggered by external sensor into signal identified by system.
HDD loss
When Hard Drive is not detected (HDD damage, power supply malfunction), or HDD auto-overwrite is
off, and free space is not enough, an alarm will be triggered.
List 5-1
17
User Manual
EMAIL Setup
Click [Email Set] to enter into the interface shown as Picture 5-27.
Picture 5-27
On the [EMAIL] screen, when Enabling [Email] option, you can
set its parameters shown as Picture 5-28.
Picture 5-28
SSL: is a security link transport protocol. You can encrypt your communication info (including your email)
using SSL to prevent hackers from monitoring your email or communication info and even your
password.
Generally Gmail.com server set SSL to [On] shown as Picture 5-28, and other mail server to [Off]. If your
setting is still not right, please contact the web site where you have applied for your email box to get SMTP
port and SSL of mail box.
SMTP Port: indicates sender port of SMTP server. Generally the SMTP port value is 25, but there are
exceptions, for example, SMTP port of G-mail server should be 465.
SMTP server: indicates server address you use.
Sender email: indicates sender’s email address. The email address should be consistent with the
server you use. That is to say, when you use email address – aaa@gmail.com, the according server
should be smtp.gmail.com.
Receiver address: indicates receiver’s email address. The email address is used to receive image
transmitted from motion detection alarm of DVR. Please clear the images you have received as soon as
possible to avoid overloading your email account.
Note: Sender email is required to enable IMAP/POP3/SMTP function (details please refer to Picture
5-29 & Picture 5-30, which show IMAP/POP3/SMTP Enable setting function for Gmail and SINA mail). Login
your GMAIL ID and turn to Settings page. Find out Forwarding and POP/IMAP option and then tick-select
[enable IMAP] option.
Picture 5-29
18
User Manual
Picture 5-30
If you can’t receive email alarm information successfully, please check below points:
DVR connection is normal or not;
The receiver and sender email support SMTP protocols or not;
Emails account setting is correct or not;
Email alarm parameters configuration is right or not;
DVR is on the status of I/O alarm or Motion detection or not.
5.3.6.3 PTZ setup
Enter into [Main menu Device PTZ Setup] to select the
channel you desire to control and set PTZ protocol (Pelco-D or
Pelco-P), Baud Rate (1200, 2400, 4800, 9600), Data bit (8, 7, 6, 5),
Stop bit (1, 2), Parity Check (None, Odd, Even, Mark, Space),
Address Code and Cruise status respectively. Please note the PTZ
device can be activated only when a channel in connection with the
PTZ camera is selected
Picture 5-31
5.3.6.4 Mobile
The DVR is currently compatible with mobile phones running Andriod, Windows Mobile and Symbian
operating systems on 3G networks. Details access methods please refer to separate Mobile phone Access
Instructions.
Click [Main menu Device Mobile] to enter into [Mobile]
menu shown as Picture 5-32.
User Name: indicate user name of DVR.
User password: indicate user password of DVR
Server port: Mobile monitoring port. Setting range is between
1024 and 65535. Please note that
Explanation: Please connect DVR to Internet before setting
DVR port number and the server port no is not equal to network
menus.
Picture 5-32
Note:
1. The user name and password you enter can not be empty.
2. The Server port no is not equal to network web port you set.
You should forward the server port number to router (details please refer to section 5.2.3 – Network setting)
19
User Manual
Mobile Viewer’s Access Instruction
The DVR is currently compatible with mobile phones running Windows Mobile, Symbian, Iphone,
Blackberry and Androids operating systems. Below are these Mobile Viewer’s installation procedures.
1、Windows Mobile :
1) First you need to copy a program named as “Aseesetup.CAB” that is included on the CD provided by
the DVR to the mobile phone.
Pic01
Pic02
Pic03
2) Click the program “Aseesetup” shown as Picture 1 and choose an installation location shown as
Picture 3 after the initialization.
3) Click [Install] button to start the installation processing shown as Picture 2.
4) After finishing the installation, click the icon named “Asee” shown as Picture 4 to run the program.
5) Now you are allowed to enter into the program screen shown as Picture 5.
Pic05
Pic06
Pic04
【CH】click [Pull-down] menu to select the channel you need to monitor.
【Connect】click the button to enter into the live image of the channel you selected
【Setup】click the button to allow you set parameter of the mobile viewer.
Function buttons in the bottom from Left to right in turn are::【PTZ Direction ( left, right, up, down)】;
【Area Selection(ZOOM+、ZOOM-)】
;【Focus(focus +, focus-)】
;【Iris(I+,I -)】
;【Snapshot】.
Note: Please firstly make sure you have right PTZ parameter setting (details please refer to User
Manual-Section 5.2.6.3) on DVR, then you could control PTZ camera through your mobile phone.
The captured images will be saved to the defaulted path (Explorer Program Files Moveeye Photo file).
If you use this program first time or need to change parameter settings, please click [Setup] button to
enter into the window shown as Picture 6.
User’s Name:herein indicate the user name which have been set on DVR-[Mobile Set] menu.
Password: herein indicate the password which has been set on DVR-[Mobile set] menu.
Server: indicate public IP address connected to DVR or dynamic domain name used by DVR
Port: indicate the server port which has been set to your DVR.
Notes: enter one channel number you want to monitor
20
User Manual
Click【ok】to confirm the above setting , and system will return back the previous menu.
Auto-connect: When tick-selecting [Auto-Connect] option, the mobile phone will be auto-connected to
the DVR.
History: Clicking the button will allow you auto-record all the log histories.
Click any area of screen to toggle display modes between normal view and full screen.
2、Symbian System Mobiles:
1)First you need to copy a program named as “ASee_AL_3rd _0723.sisx” or “See_AL_5th_0723.sisx”
that is included on the CD provided by the DVR to the mobile phone (shown as Picture 7). Generally the
program is defaulted to save into mobile storage card.
Note: “See_AL_3rd_0723.sisx” apply to S60 - The 3rd edition operate system Mobile, and
“See_AL_5th_0723.sisx” to S60 - The 5th edition operate system Mobile
Pic07
Pic08
Pic09
2) Click the program “ASee_AL_3rd _0723.sisx” to start the installation shown as Picture 8
3) Choose Phone memory or SD card as an installation location shown as Picture 9.
4) Click [Continue] button to make sure the application program you installed may visit network or dial
phone when popping-up the dialog box shown as Picture 10.
5) After successful installation system will prompt you “Installation finished” shown as Picture 11.
6) If the program is installed into SD card, please enter into 【Application】 menu to find [Asee] icon
shown as Picture 12.
Pic10
Pic11
Pic12
Pic13
7) Click [Asee] icon to run the program, and then you will enter into the interface shown as Picture 13.
(Function buttons in the bottom in turn are:)
1 CH 1;CH 2 ;CH3;CH 4
2 PTZ Direction :left, right, up, down
3 PTZ Lens control: Focus+/-, Zoom+/- and Iris+/- from left to right in turn.
Play Bar: Play/Pause, Full screen, Snapshot, Setup, Next CHs Group and Quit
4
button from left to right in turn
Note: The snapshot images will be saved to the defaulted path-“File manager\Images”.
21
User Manual
8) For first time using or Need some change on the Parameters, click the【Setup】button,you will enter
into the window shown as Picture 14; or, Click [Play] button to enter into live display.
Address: herein indicate public IP address connected to DVR or dynamic
domain name used by DVR.
Port: indicate the server port which has been set to your DVR.
User’s Name : herein input the user name which has been set on
DVR-[Mobile Set] menu.
Password: herein input the password which has been set on DVR-[Mobile
Set] menu.
Channel: select one channel you want to monitor
User Defined: Enter channel title named by you.
Option: include playback list and history list
Pic14
3、Iphone:
1) Visit Apple website http://www.apple.com/itunes/ to download & install the iTunes program.
2) Run the iTunes program, and then click the Menu- [Store Search] to enter into its sub-menu.
3) On the [Search] mode, enter the characters “ASee” to search the program “ASee”.
4) Download and install the “ASee” program.
5) After finishing installation, [ASee] icon will be displayed
to mobile phone interface shown as Picture 15.
①
②
③
④
⑤
Channel select
PTZ Direction ( left, right, up, down)
Area Selection(ZOOM+、ZOOMFocus(focus +, focus-)
Aperture(I+,I -),).
⑥
Function buttons from left to right in turn are: Play/Pause, Snapshot, setup, Next CHs Group and help.
Pic15
Pic16
Pic17
(3)We have introduced Monitor point setting in the previous Sybian and Windows system setting. The
setting method for Iphone is same as the Sybian and Windows system. Please refer to the previous section.
①
②
③
④
⑤
Enter device title
Enter IP address of the DVR
Enter DVR web port
Enter user name of DVR
Enter password of DVR
22
User Manual
⑥
Click the button to preview History record
4、Blackberry mobile:
1)
2)
3)
4)
5)
6)
7)
Download and install the Blackberry Desktop Manager on your PC
Connect your Mobile to your PC via USB cable
Open the Desktop Manager
Choose [Application Loader ] from the Main Menu shown as Picture 18
Click [Start] Button on the 【Add/Remove application】menu shown as Picture 19
Click [browser] button and tick-select [ASee.alx] file shown as Picture 20
Click [Finish] button to finish the installation shown as Picture 21.
Pic18
Pic19
Pic20
Pic21
Setup and operation on the Blackberry phone viewer
1) The Blackberry viewer will be installed to the [Downloads] directory shown as Picture 22.
2) Enter into the [Downloads] directory, and then click the [ASee] icon shown as Picture 23.
Pic22
Pic23
23
User Manual
3)
Enter into the below interface.
1 ---Connect/disconnect
2 ---full screen
3 ---snapshot
4 ---setup
5 ---help
6 ---Next CHs Group
7 ---PTZ Control
4)
Pic24
Enter the Monitor DVR info in the below Setup Menu;
Pic26
Pic25
4.1、Select the Network Type supported by Blackberry phone.
Pic27
Pic29
4.2 Click [Save] button to save the above setting, and system will return back to Live display.
4.3 Click the [History] button to enter into the History List shown as Picture 28.
4.4 Highlight one record and click [Enter] button to enter into pop up menu. When selecting [Open]
option, system will directly be connected to the DVR and defaulted to display the CH1.
4.5 When selecting [Edit] option, system will allow you edit the history record.
4.6 When selecting [Delete] option, the history record will be deleted.
Pic30
24
Pic31
User Manual
5) Click [Next Page] icon to search [Channel] option shown as Picture 32 and Picture 33, and then
choose the channel you want to display.
Pic32
Pic33
6) Click [Full screen] icon to enter into full screen display mode, again click the [Trackball] button of
mobile to quit the full screen mode.
7) Click [Next page] button to find the [PTZ Control] icon and enter into the mode. Now you could
freely control your PTZ camera through your Mobile phone.
8)
9)
Pic34
Pic35
Click [Help] button to view the software’s Help instruction.
Click [Close] button to exit the program shown as Picture 35.
5、Androids Mobile
1.
Please make sure the software environment support on your Android Mobile, such as Apkinstaller.
Make sure your mobile have been connected to network and could download the software.
2.
Pic36
Pic37
Pic38
Pic39
Enter into [Program] option and highlight [E-market] icon shown as Picture 37.
Pic40
Pic41
25
Pic42
Pic43
User Manual
3. Enter into the [E-market] interface shown as Picture 38.
4. Click [Search] icon on the upper right corner and input “Apkinstaller” shown as Picture 39, to search the
Apkinstaller program.
Highlight and install the program you searched shown as Picture 40 and Picture 41
5. Follow up the installation steps shown as Picture 42 and Picture 43
6.
7.
8.
9.
10.
Pic44
Pic45
Pic46
Pic47
Enter into [Program] file and click [Apkinstaller] icon shown as Picture 44
Find the ASee.apk file you want to install shown as Picture 45
Click the software to install to your phone shown as Picture 46 and Picture 47.
Enter into [Program] option to click [ASee] icon shown as Picture 48.
Enter into [ASee] main interface shown as Picture 49.
Pic48
Pic49
Pic50
1
CHs Select
2
PTZ Direction
3
Zoom+/-
4
Focus+ -
5
Iris +/-
6
Function buttons from left to right in turn are: Play/Pause, Snapshot,
setup, Next CHs Group and help.
Setting Menu
Address: Enter the IP address of the DVR
Port: Enter the Mobile Port No. Of the DVR
Device Name: Enter DVR name (User defined)
User ID: Enter the User’s Name
Password: Enter the User’s Password
History: Click the [History] button to preview History record
Enter the testing device infos
11. Help Instructions.
12. History Record and auto-record info
26
User Manual
5.3.6.5 Motion Detect Setup
Click [Main Device Motion] to enter into the [Motion Detection]
menu shown as Picture 5-33.
The [Motion detection] Menu has three sections, including
Channel Status, Sensitivity and Motion area.
Channel STATUS: This option allow you enable motion detection
on any channel.
Picture 5-33
SENSITIVITY: This option allows you to set sensitivity level of
motion detection from higher to low with 4 being the most sensitive.
MD AREA: This option allows you select the area you want to be sensitive to motion.
The channel is separated into a 13X10 area. When any object
moves into the motion detection area, and the area where the
object is located is displayed in red recording will be triggered. In
the semi-transparent area the motion detection is off.
Picture 5-34
5.2.7 System3
The [System] Menu includes the below sub-menus: Time Set,
User Password, Audio/Video Setting, Language select, System Info
and System Maintenance.
After entering into the [System] menu, you can configure the
relative parameters to meet your needs.
After entering into the [System] menu, you can configure the
relative parameters to meet your needs.
Picture 5-35
5.3.7.1 Time Setting
On the [System] menu screen, click [Time] icon to enter into [Time
set] menu shown as Picture 5-36.
Now you are allowed to modify system date, time, date/time
format and time zone, setup DST (day saving time) status and
mode.
Picture 5-36
5.3.7.2 Password
This option allows you set the device ID for the DVR and set the
system password if you want to use one. The new passwords will
be available after clicking [APPLY] button.
Picture 5-37
Picture 5-37
27
User Manual
When you set Password Enabled to “ON” (shown as Picture
5-38), you can setup a user password and administrator password
respectively. The password supports up to 6 characters.
The password defaulted by system is 123456.
Picture 5-38
5.3.7.3 Video/Audio Setup
Click [Main Menu System Video/Audio] to setup Video and Audio parameters shown as Picture 5-39 (a).
Picture 5-39(a)
Video System: allow you set Camera system (PAL, NTSC).
VGA Resolution: include five options - 1280×1024、1024×768、800
×600 and 1440×900.
OSD Device: allow you select video output device, Main output and
VGA. User can hold pressing [Rew] button on the front panel to
convert output device quickly.
Poll time:allow you select sequence time between from 5s and
300s.
Click the [Volume] and/or [Margin] options on the right-bottom
corner of the Video/Audio screen to adjust the volume and/or margin
respectively. Details please kindly find the Picture 5-39 (b).
Picture 5-39(b)
5.3.7.4 Language
Enter into [Language] menu to select the language you want to use
on the DVR (shown as Picture 5-40), and then click [APPLY] button.
The selection will be available after system Auto restarts.
Picture 5-40
5.3.7.5 System Information
Enter into [System Information] menu to view system info,
including Device type, Software (firmware) version, IE version and
MAC address etc.
When connecting multiple DVRs to the same local area network
environment, you need to change MAC address for each DVR
respectively; otherwise, you may not connect these DVRs to network.
Picture 5-41
28
User Manual
5.3.7.6 Maintain
This option allows you recover the DVR settings to factory
default settings, update system software (firmware), and set system
auto-maintenance. Click [Main menu System Maintain] to enter
into the [System Maintain] menu shown as Picture 5-42(a).
Auto Maintain: After enabling [Auto Maintain] function,
system will perform regular maintenance as per the schedule you
have set. Please note the [Auto Maintain] function will be available
only when DVR is on the Main interface and have no user online.
Picture 5-42(a)
System Update: Copy the file named with “dvrupgrade” to U flash drive; and connects U flash drive to
USB port of DVR, and then click [System upgrade] menu.
Default: Click the [Load Default] button to recover all the DVR settings back to factory set.
Reboot: Click the [Reboot] button to restart the device manually.
Power off: the button allows you cut the power after making sure the DVR shutdown.
Note:
Picture 5-43
Picture 5-42(b)
1. Please obtain the updated program from local supplier before system updating.
2. Please not cut power and unplug U flash disk during the update.
3. System will automatically restart after finishing system update.
4. User needs to manually recover the ex-factory default setting after restarting.
5.4 Menu Lock
Considering a system safety feature you can click [Menu Lock] menu to lock menu when leaving the
DVR shown as Picture 5-44(a). If you want to login in the DVR again, you would input device code and
password shown as Picture 5-44 (b).
Picture 5-44(b)
Picture 5-44(a)
Explanation: Common user only has the authority to search recordings, but Administrator has
full authority over Main Menu operations.
Any user can start and close manual record on the non-record mode.
29
User Manual
5.5 Record search
You could enter into [Record Search] menu from Pop-up menu conveniently and quickly and search/playback
the record histories. We introduced Record search details previously in section 5.2.4.
5.6 PTZ Control
Picture 5-45
Picture 5-46
Picture 5-47
Picture 5-48
Open auto cruise function on PTZ setting menu if you want to setup cruise function (system default: on),
and set up cruise channel, cur point and total quantity and stop time etc.
Channel select: select one channel with PTZ camera
Total: set up pre-set bit quantity
Pre: indicates starting point cruised. System default point is 01.
STP:sets the stop time at each point
GOTO:allow you go to a specific preset point.
SET:allow you set a set of specific preset points of a PTZ camera.
1. Select a camera you desire to set a preset point;
2. Adjust the camera in a desired direction
3. Click [Set] to set the point as preset point
4. Click [Save] to save the preset point
5. Follow the above step to add one more preset point.
CLR: allow you delete one selected preset.
Note: Up to 255 preset bits for the DVR can be stored. However, actual preset quantity differs depending on
PTZ performance.
5.7 Record
Enter into Pop-up menu to select the [Record] option. Now you can start manual record function, or you
also can click [Rec.] button on the Front panel or Remote controller to activate manual record. Please stop
record manually once you activate manual record.
5.8 Stop Record
To stop record quickly, please enter into pop up Menu to select [Stop] option.
30
User Manual
Chapter 6: Web Application Manager
6.1 Plug-in download and installation
Open your web browser and input the IP address and web port of DVR, such as :
http://172.18.6.202:8080/ . If your computer is connected to internet, it will download and install “ActiveX”
Plug-in automatically. If your computer system is Vista, you may need to setup the user authority. Details
please refer to the below picture: Start →setup→ control panel(Cancel Tick “√” use UAC to help protect
your computer and confirm OK).
Reminder: If the plug-in program is not downloaded successfully, please check if your browser’s safety
level or firewall setting is too advanced. Please run IE →Tools→Internet options→Internet Custom
level→Enable the options. If it is first time login, it need about one minute to finish download and install
plug-in, please wait patiently. Also refer to section 5.2.3 Network Setup to make sure network configuration is
correct, ports are forwarded correctly, and ActiveX is enabled.
Note: Cause DVR sytem update, If you want to delete old IE webcam at the computer which
already login before, input the command characters: “regsvr32/u HiDvrOcx.ocx
on “Start→Menu
→Run ”
6.2 web Client Log-in
After plug-ins installation, please input user name and password and click [Log-in] button, and then you
can view DVR remotely through the Web Client. Note that if use IE to login must input user name. default
password is empty. System allows Administrator to set new password as per instructions in section 6.3.1.3 [Device Manage] menu. Login as Admnistrator can setup every parameter ; Login as user only can setup
live, playback ,logout,but can not setup other parameters. 4-CH allow respectively five users on-line
simultaneously, and 8-CH DVR allow three users
Picture 6-1
31
User Manual
6.3 Web Client Interface
6.3.1 Menu Bar
Menu bar include [Live], [Playback], [Remote setting], [Local Setting] and [Logout] option
6.3.1.1 Live Display
After PC Web Client logging in, system will be defaulted to enter into Live mode and connect Audio.
Also can set record manualy via shortcut key , like picture 6-2(a)and(b)
Left key ——
Click the icon of one channel to display the channel’s image
Click the icon to start manual record. save path is setup on “local setting”
Live display Key function :
Snap screen
:clicking the button will capture the live image from one selected channel and save
the image with *.bmp format to PC.
Record
:clicking the button will remotely record the live images and automatically save the
recording to a specified position。
Channel display mode
: the icons stand for the Single channel display, Quad
display, 9-split mode, 16-split mode
Full screen
:full screen mode,click “X”in the upper right corner of screen to close
If want to play Audio, click the channel that you want.。
Volume control
:clicking the icon to adjust sound volume.
PTZ Control
Reminder:refer to the picture Mark(picture 6-2(b))
PTZ direction control: the buttons allows you control PTZ moving direction. The middle is scan button
Zoom, Focus and Iris control: the buttons allows you control PTZ moving direction, zoom, focus and iris.
Preset bit control
preset cruise control
Pan & Tilt Preset: indicates current present or
input the starting point you desire to cruise firstly.
:On the Live mode, click the icon to load the last preset point you set.
:allow you set a series of specific preset points of a PTZ camera, you can setup new
preset base on last setting. But the preset number is limited.(refer to Chapter 5.5 PTZ control) . after
setup can click cruise to preview , then click
to save it
:input the preset point No. you want to display and click the icon to quickly go to the
preset point on live mode.
: delete the current preset point
:enable/disable the [Cruise] function
32
User Manual
Picture 6-2(a)
①
③
②
Picture 6-2(b)
33
User Manual
6.3.1.2 Playback
Click [Playback] option to playback record files from remote DVR by selecting relevant date, channel
and type. Details please refer to below Picture 6-3
Picture 6-3
Double-click any file listed or highlight any file and click [Play] button to play the selected recording file.
Also can select channel and file type. Click [download] to download and save selected recording file to
specified saving path shown as picture 6-4
Picture 6-4
Picture 6-4
You can set [Save Path] option on the [Local Setting] menu.
The [Play control] bar is located at the bottom of the interface, include [Play], [Pause], [Stop], [Slow Play],
[Fast Play], [Next Frame] and [Volume adjust] option.
6.3.1.3 Remote Setting
Click [Remote setting] option and enter into the interface shown as Picture 6-5. you will see sub-menu of
perform the parameter settings of Display, Record,Alarm, Network ,Device and System
Channel Parameters
`Default enter “channel ” setting menu, you can setting remotely and save on the DVR,
Picture 6-5(a)
34
User Manual
4CH
8CH
Picture 6-5(b)
Click [Copy Setting to] option on the right-bottom corner of the interface to copy all the remote setting to
any channel shown as Picture 6-5(b)
Record setting
Enter into [Record Setup] option to set record control parameters, including record enabling, audio
enabling, Pack time, Record mode and Frame,Quanlity, Resolution etc. (shown as Picture 6-6)
Picture 6-6
If Frame rate is adjustable, you can setup Picture Quality and Frame rate for each chanel.refer to picture 6-7
Picture 6-7
35
User Manual
Select [Schedule] mode in record setting will see screen as picture 6-8,then can setup record mode on
the form which are the same method on DVR menu
Picture 6-8
Alarm Parameters
Click [Alarm Parameters] option to enter into the Alarm Config interface, which include I/O Status,Video
cover, Video loss, HDD loss ,HDD space, Prerecord and Alarm time. Also can setup Email alarm and Full
screen enlarge when in Alarm. Show as picture 6-9
Picture 6-9
Network Parameters
Click [Network] option to enter into [Network setting] menu, including [Basic character], [PPPoE],
[DDNS], and [Email set] (Picture 6-10).
Picture 6-10(a)
36
User Manual
Picture 6-10(b)
Picture 6-10(c)
Picture 6-10(d)
Device Parameters
Click [Device] option to enter into the interface . Now you can check Hard disk info (Picture 6-11), PTZ
Parameters (Picture 6-12) , Mobile info (Picture 6-13) and Motion (Picuture 6-14).
Picture 6-11
37
User Manual
Click[PTZ Parameters ] to setup PTZ control ,the setting are same with DVR menu as picture 6-12
Picture 6-12
Mobile phone setup,the same with DVR menu setup as picture 6-13
Picture 6-13
Click“Motion Detection”to setup each channel parameters,including Sensitivity and Motion Area. The
sam with DVR menu setup as picture 6-14 and 6-15
Picture 6-14
38
User Manual
Picture 6-15
System management
Extend [System] option to enter into sub menus – System setting, User Authority , DST(Daylight saving
time) and DVR information shown as Picture 6-16
Picture 6-16
Click [User] to setup Authority, Log-in name and password for different user,as Picture 6-17
Picture 6-17
39
User Manual
DST setting as picture 6-18
DVR system information as picture 6-20
Picture 6-18
Picture 6-19
6.3.1.4
Local setting
The option allows you set [Record Save Path], [snapshot Save Path] and [File Save Path] shown as
Picture 6-20.
Picture 6-20
Note:Record save path --- Save file of remote manual record from netwok
File save path --- Save download recording file from DVR.
40
User Manual
Chapter 7: Specifications
Model
parameter
4CH
8CH
NTSC/PAL(Optional)
Video System
Video/Audio
Compression Format
Video:H.264
Video I/O
4-CH BNC input;
2-CH BNC output;
VGA (Optional);
8-CH BNC input;
2-CH BNC output;
VGA(Optional);
Audio I/O
4-CH input / 2-CH output
8-CH input / 1-CH output
Display Resolution
D1:704×576(PAL)
Display frame rate
Single Channel
Record Resolution
PAL: CIF(352*288)
HD1(704*288)
NTSC:CIF(352*240) HD1(704*240)
Record Total frame rate
PAL:50 fps@D1、100 fps@HD1、200 fps @CIF
NTSC:60 fps@D1、120 fps @HD1、240 fps @CIF
Image Quality
Best / Good / Middle
HDD
Support USB removable HDD and SATA HDD
Record Mode
Always, Scheduled, Manual, motion, Alarm, Web Client record.
Pack Time
15/30/45/60 min (adjustable)
Backup Function
Support U flash disk, removable HDD, recorder and network backup;
Backup file format is *.264 format and network file will automatically be
backed-up to AVI format).
Playback Mode
Normal play, Fast Forward, Rewind and slow play frame by frame.
Alarm I/O
4-CH input / 1-CH output
Alarm Mode
Motion Detection, Sensor triggered, Video Loss, HDD Full, HDD Error
PTZ control
Embedded RS-485 port / supports PELCO-P & PELCO-D protocol.
USB Port
Support Mouse, removable HDD and U flash disk backup and upgrade.
Network Interface
One RJ-45 10M/100M self-adaptable Ethernet interface.
Network Function
Support Mobile surveillance, IE browsing, Remote Live surveillance and
parameter setting.
Network Protocol
Supports TCP/IP, DHCP, UDP, DDNS, PPPOE network Protocol
IR remote control
Support IR remote control.
Power Adapter
DC 12V&3A
Power Consumption
10~15W (excluding HDD)
Operational Temperature
10℃~+40℃
Operational Humidity
10%~90%
Audio:8kHz*16bit ADPCM
704×480 (NTSC)
PAL:25 fps ,NTSC:30 fps
D1 (704*576)
D1 (704*480)
8-CH input / 1-CH output
List 7-1
41
List 7-1
User Manual
Chapter 8: Appendix
8.1 Record Alarm setting
Please refer the below matrix: “⊥” stand for “only alarm but no record”; “AMR” stand for “alarm record”;
“NLR” stand for “normal record”; and “NOR” stand for “ no record”. Once alarm is triggered, alarm icon will occur,
and when many alarms are triggered, alarm remarks will occur on the screen.
Record alarm setting
Alarm icon
Record Mode
Scheduled recording
Record after
AMR
power on
NLR
NOR
Manual Record
AMR
AMR NLR
⊥
NLR
AMR
AMR NLR
⊥
NLR
HDD loss, HDD Full
⊥
⊥
⊥
⊥
⊥
Video Loss
Video Loss ⊥
⊥
⊥
⊥
⊥
List 8-1
In the record mode, [ ] icon or [ ] icon will appear on the screen. But when [ ] icon and [ ] icon appear on
the screen that means a motion alarm is triggered. When [ ] icon appears on the screen, that means HDD alarm has
occurred.
Alarm
mode
MD alarm
I/O triggered alarm
8.2 Sustainable Record Time List
The sustainable record time differ depending from Resolution, Para, Video Input, Image parameter and Audio input etc.
Factor:
Audio set to ON / 4-CH video input / Twenty-four hours Continuous record / 250G HDD / Unit: Day
Quality (Image Quality)
Resolution
Best
Good
Middle
D1
6
8
11
HD1
6
8
11
CIF
8
11
14
List 8-2
Calculation formula:
250 × 1024
1402 × 24
When using 250G HDD and Record for 4-CH occupies 1402M space per hour, system can continuously record 183
hours.
8.3 Mail box server List
Web site
www.163.com
Mail box
Sender server(25)
Receiver server(110)
@163.com
smtp.163.com
pop3.163.com
@vip.163.com
smtp.vip.163.com
pop.vip.163.com
@188.com
smtp.188.com
pop.188.com
@126.com
smtp.126.com
pop3.126.com
@netease.com
smtp.netease.com
pop.netease.com
42
User Manual
@yeah.net
smtp.yeah.net
pop.netease.com
@qq.com
smtp.qq.com
pop.qq.com
smtp.163vip.net
popx.163vip.net
@sina.com.cn
smtp.sina.com.cn
pop3.sina.com.cn
@yahoo.com.cn
smtp.mail.yahoo.com.cn
pop.mail.yahoo.com.cn
@yahoo.com
smtp.mail.yahoo.com
pop.mail.yahoo.com
google.com
@gmail.com
smtp.gmail.com(465/587)
pop.gmail.com(995)
www.china.com
@china.com
smtp.china.com
pop.china.com
www.sohu.com
@sohu.com
smtp.sohu.com
pop.sohu.com
smtp.163.net
pop.163.net
smtp.163vip.net
pop.163vip.net
www.qq.com
163.net
www.sina.com
www.yahoo.com
Mail.163.com
Mail.163vip.com
Mail.tom.com
@tom.com
smtp.tom.com
pop.tom.com
Mail.263.com
@263.net
smtp.263.net
pop3.263.net
smtp.x263.net
pop.x263.net
smtp.263.net.cn
pop.263.net.cn
smtp.139.com
pop.139.com
smtp.21cn.com
pop.21cn.com
vip.21cn.com
vip.21cn.com
etang.com
smtp.etang.com
pop.etang.com
elong.com
smtp.elong.com
pop3.elong.com
x263.net
263.net.cn
139 mail box
@139.com
21cn.com
Vip.21cn.com
List 8-3
8.4 Troubleshooting
1.
2.
3.
4.
5.
6.
7.
8.
9.
Q: What can I do if the system does not detect the HDD?
A: Check if the power supply system is properly connected and data cord and power cables are securely
connected.
Q: We have changed the password but do not remember the new password, how can we access the system?
A: If you forget system password, please consult with the service personnel.
Q: We are not getting any video signal on the DVR, what is wrong?
A: Check camera video cable and connections; or check monitor video cable and connections; or confirm that the
camera has the power and / or check camera lens setting.
Q: Why some channels display just a blank screen even if they receive video sources?
A: Check if the camera is connected to the system properly displays the image; check if the camera is properly
supplied with power.
Q: Can the DVR have problems if it gets too hot, how can I prevent this?
A: The DVR has a fan to help it dissipate heat while it is running. Please place the DVR in a place where there is
good air circulation and away from heat sources to increase stability and life of the DVR.
Q: “Record” Can not work normally, how to deal with?
A: Check if the current screen is in Play mode, pressing [Stop] button to exit the Play mode and then you can
enter into the [Record] function.
Q: Why the Remote Controller can’t work normally?
A: Check if the battery is power off; or check if the Remote Controller is broken.
Q: Can we records whilst playing-back?
A: Yeah, you can do it. The system support you records whilst playing-back.
Q: Can we erase some recorded file from DVR.
A: Considering the safety factor, you can’t delete the recorded file directly from the device. When you actually
erase all the recorded files, please select HDD format function
43
User Manual
10. Q: Why does the Buzzer keep sounding?
A: Please check if motion detection is on and the system has detected motion, make sure the HDD is being
detected and has sufficient space available; check if video has lost etc.
11. Q: Why can’t stop [Stop] function?
A: Pressing [Stop] button only can stop manual record. If you want to stop Scheduled record, please revise to [No
Record] during this period.
8.5 System Configuration
4-CH DVR
8-CH DVR
44
User Manual
8.6 Accessories
Power Cord
Power Supply
USB Mouse
Remote Controller
45
User Manual
Software CD
The material in this document is the intellectual property of our
department .
No part of this manual may be reproduced, copied, translated,
transmitted, or published in any form or by any means without our
department prior written permission.
Our products are under continual improvement and we reserve the right to
make changes without noti ce. But no guarantee is given as to the correctness
of its contents.
We do not undertake any responsibility for the harms cause by using our
product.
The model of the products in the user's manual only for recognition, but
these names also perhaps are belong to other company's registered
trademark or the copyright.
The product picture may differ from the actual product, only for your
reference. The accessories will probably be different according to the
different sel ling areas. For details of accessories, please refer to your local
distributor.
Cop yrigh t r es erve d
ٛ
ٛ
ٛ
ٛ
ٛ