Craftsman 320.17562 Operator`s manual

Operator's
Manual
ICRA
MAN°I
flEX E
12.0-VOLT LITHIUM-ION
CORDLESS RIGHT-ANGLE
IMPACT DRIVER
Model No. 320.17562
c_ius
LISTED
• Warranty
Powered by an
ENERGYSTAR_
qualified battery
charger for a
better environment
_k WARNING:
To reduce
• Safety
• Assembly
• Operation
• Maintenance
the risk of
injury, the user must read and understand
the Operator's manual before using
this product.
Sears Brands Management
IL 60179 U.S.A.
www.craftsma n.com
• Espa_ol
Charge battery
before first use
Corporation, Hoffman Estates,
InuPL4
-'1ml_ [o_ [_o__
Warranty
page 2
Safety Symbols
page 3
Safety Instructions
page 5
Description
page 9
Assembly
page 10
Operation
page 11
Maintenance
page 19
Troubleshooting
page 21
Exploded
page 22-24
View and Part List
Sears Repair Parts Phone Number
The purpose of safety symbols is to attract your attention to possible dangers.
The safety symbols and the explanations with them deserve your careful
attention and understanding.
The symbol warnings do not, by themselves,
eliminate any danger. The instructions and warnings they give are no substitutes
for proper accident prevention measures.
WARNING:
Be sure to read and understand all safety instructions in this
manual, including all safety alert symbols such as "DANGER," "WARNING,"
and "CAUTION"
before using this Right-Angle Impact Driver. Failure to following
all instructions listed in this manual may result in electric shock, fire, and/or
serious personal injury.
SAFETY
SYMBOL
MEANING
SAFETY ALERT SYMBOL:
Back Cover
May be used in conjunction
CRAFTSMAN ONE YEAR LIMITED WARRANTY
FOR ONE YEAR from the date of purchase, this power tool, battery
pack and charger are warranted against any defects in material or
workmanship. With proof of purchase, defective product will be
replaced free of charge.
For warranty coverage details to obtain free replacement,
web site: www.craftsman.com
or pictographs.
which,
if not
_,
situation,
which,
if not
situation,
which,
if not
WARNING:
Indicates
a potentially
hazardous
could result in death or serious injury.
CAUTION:
avoided,
Indicates
an imminently
may result in death or serious
hazardous
injury.
NOTE: These inform the user of import information and/or instructions that
could lead to equipment or other property damage if they are not followed. Each
message is preceded by the word "NOTE," as in the example below:
NOTE: Equipment
not followed.
WARNING:
Hoffman Estates, IL 60179
by a qualified
and/or
property
damage
may result if these instructions
To ensure safety and reliability,
service technician
are
all repairs should be performed
at a Sears parts & Repair Service Center.
INSTRUCTIONS!
_i, WARNING: The operation of any power tool can result
READ ALL INSTRUCTIONS
in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool
operation, always wear safety goggles or safety glasses
with side shields and a full-face shield when needed.
This cordless 12V Right-Angle Impact Driver has many features for making its
use more pleasant and enjoyable. Safety, performance, and dependability
have
been given top priority in the design of this product making it easy to maintain
and operate.
We recommend a Wide Vision Safety Mask for use over
eyeglasses or standard safety glasses with side shields.
Always use eye protection which is marked to comply with
ANSI Z87.1
_lk WARNING;
Some dust created by using power tools contains chemicals
known to the state of California to cause cancer and birth defects or other
17562
OR CAUTION.
situation,
_,
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
reproductive
with other symbols
WARNING,
visit the
This warranty is void if this product is ever used while providing
commercial services or if rented to another person.
SAVE THESE
DANGER,
DANGER: Indicates an imminently hazardous
avoided, will result in death or serious injury.
avoided,
This warranty does not cover nut driver bits and screw driver bit which
are expendable parts that can wear out from normal use within the
warranty period.
Sears Brands Management Corporation,
Indicates
harm.
Manual_Revised_$O
0607
Page 2
17562
ManuaLRevised_iO
0607
Page 3
SAVE THESE INSTRUCTIONS
Some of these following
and learn their meaning.
symbols may be used on this tool. Please study them
Proper interpretation
of these symbols will allow you to
operate the tool better and safer.
SYMBOL
GENERAL
_,
NAME
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency
W
Watt
Power
min
Minutes
WARNING:
Read all safety warnings
the warnings and instructions
personal injury.
DESIGNATION/EXPLANATION
V
POWER TOOL SAFETY WARNINGS
Save all warnings
(cycles
and instructions.
may result in electric
and instructions
for future
Failure to follow
shock, fire and/or
reference.
The term "power tool" in all warnings refers to your mains-operated
power tool or battery-operated
(cordless) power tool.
per second)
serious
(corded)
WORK AREA SAFETY
Time
•
Alternating
--_
nO
]
Direct
Current
Current
Type or a characteristic
No Load Speed
Class
.../min
Type of current
Rotationai
II Construction
Per Minute
speed,
Double-insulated
of current
Keep your work area clean and well lit. Cluttered
accidents
or dark areas invite
Do not operate power tools in explosive environments, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks,
which may ignite the dust or fumes.
at no Ioad
construction
Revolutions,
strokes, surface
orbits, etc., per minute
Keep children and bystanders away while operating a power tool.
Distractions may cause you to lose control.
speed,
ELECTRICAL SAFETY
Wet Conditions
Read The Operator's
Alert
Manuai
Eye Protection
O
Safety
,_
No Hands
No Hands
No Hands
No Hands
Alert
Symboi
Symbol
Symboi
Symboi
Hot Surface
17562 ManuaLRevised_$O 0607
locations.
Do not expose
Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce the risk of electric shock.
to rain or use in damp
read and understand
operator's
manuai
To reduce the risk of injury, user must
before using this product.
Avoid body contact with grounded surfaces, such as pipes, radiators,
ranges, and refrigerators.
There is an increased risk of electric shock if your
body is grounded.
glasses with side shields and a full face
Always wear safety goggles or safety
shield when operating this product.
Precautions
that involve
Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
your safety.
Do not abuse the cord. Never use the cord for carrying, pulling, or
unplugging the power tool. Keep the cord away from heat, oil, sharp
edges, or moving parts. Damaged or entangled cords increase the risk of
electric shock.
Failure will
blade
to result
keep your
in serious
hands personal
away frominjury.
the
Failure will
blade
to result
keep your
in serious
hands personal
away frominjury.
the
•
When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
•
If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
•
NOTE: The term "residual current device (RCD)" may be replaced by the
term "ground fault circuit interrupter (GFCI)" or "earth leakage circuit breaker
(ELCB)".
Failure will
blade
to result
keep your
in serious
hands personal
away frominjury.
the
blade
in serious
Failure will
to result
keep your
hands personal
away frominjury.
the
To reduce
avoid
contact
the with
risk of
anyinjury
hot surface.
or damage,
Page 4
17562
ManuaLRevised_lO
0607
Page 5
•
Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
Use the battery only with the charger listed:
BATTERY
PACK
CHARGER
320.11221
PERSONAL
320.10006
Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
SAFETY
Stay alert, watch what you are doing, and use common sense when
operating a power the tool. Do not use a power tool while tired or under
the influence of drugs, alcohol, or medication. A moment of inattention
while operating power tools may result in serious personal injury.
Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories, blades, etc. in accordance with these
instructions and in the manner intended for the particular type of
power tool, taking into account the working conditions and the work
to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
Use personal protective equipment. Always wear eye protection.
Protective equipment, such as dust mask, non-skid safety shoes, hard hat,
or hearing protection, used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure that the switch is in the OFF
position before connecting to power source and/or battery pack,
picking up, or carrying the tool. Carrying power tools with your finger
on the switch or energizing power tools that have the switch on invites
accidents.
BATTERY
TOOL USE AND CARE
Recharge only with the charger specified by the manufacturer.
A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
Use power tools only with specifically designated battery
any other battery packs may create a risk of injury and fire.
Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
When the battery pack is not in use, keep it away from other metal
objects, such as paper clips, coins, keys, nails screws, or other small
metal objects that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fire.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and
collection facilities, ensure that these are connected and properly used.
Use of these devices can reduce dust-related
hazards.
POWER TOOL USE AND CARE
Use of
Under abusive conditions, liquid may be ejected from the battery;
avoid contact. If contact accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help, Liquid ejected from the
battery may cause irritation or burns.
SERVICE
•
Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and more safely at
the rate for which it was designated.
Do not use the power
power tool that cannot
be repaired.
packs.
Have your power tool serviced by a qualified repair person using only
identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
When servicing a power tool, use only identical replacement
tool if the switch does not turn it on and off. Any
be controlled with the switch is dangerous and must
parts.
Follow instructions in the Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance instructions may create a
risk of shock or injury.
Disconnect the plug from the power source and/or the battery pack
from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
17562
ManuaLRevised_iO
0607
Page 6
17562
ManuaLRevised_iO
0607
Page 7
SPECIFIC SAFETY RULES FOR CORDLESS RIGHT ANGLE IMPACT DRIVER
Hold power tools by insulated gripping surfaces when performing an
operation where the tool may contact hidden wiring or its own cord.
Contact with a "live" wire will also make exposed metal parts of the tool
"live" and shock the operator.
Secure the workpiece. Clamping
in place better than the hand
devices or a vise will hold the workpiece
Always wait until the machine has come to a complete stop before
placing it down. The tool can jam and lead to loss of control over the power
tool.
Before performing any kind of work on the machine (e. g., maintenance,
tool change, etc) as well as when transporting and storing it, always
set the rotational direction switch to the center position. Unintentional
activation of the On/Off switch may result in personal injury.
Do not open the battery.
Protect
KNOW YOUR RIGHT-ANGLE IMPACT DRIVER (Fig.l)
Fig. 1
Sleeve
Direction of
Rotation Selector
(Forward/Center
Lock/Reverse)
LED
Worklight
FuelGauge
There is risk of a short circuit.
the battery from heat and fire. There is risk of explosion.
Wear ear protectors
hearing loss
_]__o_j
with impact
drills. Exposure
Variable
Battery Release
Button
Speed Trigger
Switch
to noise can cause
Use protective gloves when removing the bit from the tool, or first allow
the clamp to cool down. The bit may be hot after prolonged use.
Use protective gloves when operating
to keep you from being burnt and hurt.
the tool. Protective
gloves can help
Battery Pack
PRODUCT
Keep your hands away from the motor-housing
from the vents during operation.
vents. Hot gas comes
Do not operate the tool at full-load for more than 30 seconds, as this can
cause the motor to become too hot, which may damage the motor.
Release the trigger immediately when the fasteners are sufficiently
tightened to avoid breaking the fasteners.
For best results, your battery tool should be charged in a location where the
temperature is more than 32°F (O°C) but less that 104°F (40°C). Do not store
outside or in vehicles.
Motor
12 Volt DC
Collar
1/4"
Switch
VSR (Variable Speed Reversible)
No Load Speed
0-2100
RPM
Impacts
0-3400
BPM
Manual_Revised_SO
0607
Page 8
per minute
Torque
700 in.lbs
Driver Weight
(without battery)
1.83 Ibs (without battery)
Battery Type
Lithium-Ion
Battery Voltage
12 Volt DC
Charger
120-Volts,
Optimum
17562
SPECIFICATION
17562
Input
Charging
ManuaLRevised_lO
Temperature
0607
60 Hz AC only
32°F (0°C) -104°F (40°C)
Page 9
A
ABt,WARNING: The safe use of this product requires an understanding
of the
information on the tool and in this operator's manual, as well as knowledge of
the project you are attempting. Before use of this product, familiarize yourself
with all operating features and safety rules.
VARIABLE SPEED
The variable-speed
trigger switch delivers higher speed with increased
and lower speed with decreased trigger pressure.
FORWARD/CENTER
PACKING
LED WORK LIGHT
This feature
Right-Angle Impact Driver, soft case, 1-3/8" Phillips screwdriver
bit, 1A" nut
driver bit, 3/8" nut driver bit, 5/16" nut driver bit, operator's manual.
provides
level.
WARNING:
If any part is broken or missing,
Important
WARNING:
Do not attempt
WARNING:
To prevent
do not attempt
Impact Driver or
Impact
personal
2.
While charging
a battery,
3.
If the batteries
do not charge properly:
completely
assembled.
•
Carefully remove the tool and any accessories
all items listed in the packing list are included.
•
Inspect the tool carefully
during shipping.
•
Do not discard the packing material
satisfactorily operated the tool.
17562
Manual_Revised_SO
0607
from the box. Make sure that
to make sure that no breakage
or damage
until you have carefully
if batteries
the charger will normally become
are charged
warm.
in a lamp or other appliance
B. Determine whether the outlet is connected to a light switch that turns the
power off when you turn out the lights; if so, make sure that the power is
turned on.
4.
The battery pack should be recharged when it fails to produce sufficient
power on jobs that were previously done easily or when the FuelGauge
shines red to indicate that the charge is depleted. Do not continue to use
the tool under these conditions. Repeat the charging procedure.
5,
Unplug the charger from the power supply before disconnecting
tool. Unplug the charger before attempting to clean.
6.
Battery life depends
7.
The charger is intended
Driver when
UNPACKING
has been shipped
can be obtained
to plug in the
starting that could cause serious
injury, always remove the battery pack from the Right-Angle
assembling parts.
This product
notes
A. Verify the current at the outlet by plugging
and turning it on.
to modify this 12V Right-Angle
accidental
charging
Longest life and best performance
at normal room temperature.
create accessories not recommended
for use with this tool. Any such alteration
or modification
is misuse and could result in a hazardous condition leading to
possible serious injury.
A
pack is not fully charged!
1.
power cord, attach the battery pack or operate the 12V Right-Angle Impact
Driver until the broken or missing part is replaced. Failure to do so could result
in possibly serious injury.
a
INDICATOR
First, read the safety rules, and then follow the instructions in the sections
entitled "Important
charging notes" and "Charging
the battery".
r_,."_"]
•
d _ I:] a5"4
A
CAPACITY
NOTE: The new battery
FuelGauge
charge
listed on
LIST
LOW-BATTERY
the LED worklight.
please refer to the numbers
[,] d d-'T-,_d[,] _1
The direction-of-rotation
selector located above the trigger switch changes
the direction of bit rotation. Setting the trigger switch in the OFF (center lock)
position helps to reduce the possibility of accidental starting.
Indicates the battery-pack
If any parts are damaged or missing,
the back page of operator's manual.
pressure
LOCK/REVERSE
Pressing the trigger switch illuminates
extra light for increased visibility.
•
occurred
inspected
and
Page 10
Unlike other battery
entire run time. The
you work. To signal
charged, the power
on usage, storage temperature
it from the
and time.
to be used in a vertical or floor-mounted
position.
types, Lithium-Ion battery delivers fade-free power for their
tool will not experience a slow, gradual loss of power as
that the battery is at the end of its run time and needs to be
to the tool will drop quickly.
NOTE: The LED worklight may flash slowly and the FuelGauge may not
illuminate in the case of an overload or high temperature (see BA-I-i-ERY
PROTECTION, Page 12).
17562
ManuaLRevised_lO
0607
Page 11
BATTERY
PROTECTION
Charge the Lithium-Ion
battery pack with the
correct charger.
1.
The battery circuitry protects the battery pack from extreme temperature,
over-discharge,
and over-charge.
To protect the battery from damage and
prolong its life, the battery pack circuitry will turn off the battery pack if it
becomes overloaded or if the temperature becomes too high during use. This
may happen in extremely high torque, binding, and stalling situations. This
intelligent system will shut down your battery pack if its operating temperature
exceeds 176°F (80°C) and will begin normal operation when it returns to 32°F
(0°C) - 104°F (40°C).
The LED worklight will begin to flash slowly if the battery circuitry
momentary overload.
detects
2.
Connect the charger to a
power supply.
3.
Align the raised ribs of the
battery pack with the slot in
the charger.
4,
Insert the battery pack into
the charger (Fig. 2).
5,
The charger will
communicate
with the
a
NOTE: A significantly reduced run time after fully charging the battery pack
indicates that the battery is near the end of its usable life and must be replaced.
COLD WEATHER
battery pack to evaluate the
condition of the battery pack.
OPERATION
This Lithium-Ion battery pack will provide optimal performance
in temperatures
between 32°F (0°C) and 104°F (40°C). When the battery pack is very cold, it may
"pulse" for the first minute of use to warm itself. Install the battery pack in the
tool and use the tool in a light application; after about a minute, the battery pack
will have warmed itself and will operate normally.
WHEN TO CHARGE
THE BATTERY
6.
The green lights will flash while the battery pack is charging. After charging
is complete, the green LED on the charger will be on. The flickering red light
indicates a defective battery or a bad connection between the battery and
the charger.
7.
The battery pack will fully charge if left on the charger,
overcharge.
PACK
It is not necessary to run down the battery pack charge before recharging. The
Lithium-Ion battery can be charged at any time and will not develop a "memory"
when charged after only a partial discharge.
Due to Lithium-Ion fade-free properties, the only time it is necessary to charge
the Lithium-Ion battery pack is when the pack has reached the end of its charge.
The orange LED on the FuelGauge indicates
approximately
one half of its charge.
The red LED on the FuelGauge
to be charged.
indicates
pack is depleted
THE BATTERY
0607
RED
LED
_)
GREEN
LED
ACTION
when battery returns to
32OF (0oc)_104OF (40oc)
Defective
Flashing
Off
Battery pack or
Charger/Adapter
is
defective
CHARGING
Charging
Off
Flashing
Fully
charged
Off
On
FULL
BATTERY
BATTERY
DEFECTIVE
and needs
_
Hot/Cold
battery
On
will begin
Off
HI/LO
TEMP.
(SEE
MANUAL)
BATTERY
partially charged.
A fully discharged battery pack will charge in about 30 minutes
temperature between 32°F (0°C) and 104°F (40°C).
ManuaLRevised_i0
BA-i-rERY
PACK
and
Charging
PACK (Fig. 2)
NOTE: This Lithium-Ion battery pack is shipped
the first time, fully charge the battery pack.
:$7562
(Fig. 3)
Charging
Charge the battery pack as needed.
HOW TO CHARGE
OF CHARGER
LED INDICATOR
that the battery has used
the battery
but it will not
NOTE: For your convenience, the charger can operate with most generators
inverters rated at 300 watts or higher.
LED FUNCTIONS
Remove the battery pack from the tool when it is convenient for you and your
job. "Top off" the battery pack charge by charging it for a time before starting a
big job or long period of use.
I Fig. 2
Before using it
0
Charging
is complete
in a surrounding
Page :$2
:$7562
ManuaLRevised_:$0
0607
Page :$3
CHARGING
A HOT BATTERY
PACK
If the battery pack is above normal temperature range, the red LED will
illuminate and the green LED will be off. When the battery pack cools down to
approximately
104°F (40°C), the charger will automatically
begin charging.
CHARGING
A COLD BATTERY
PACK
3.
If a different battery pack charges
pack (see Maintenance section).
If a different
defective.
BATTERY
normally,
battery pack also indicates
dispose
"defective,"
of the defective
IocW reverse) selector
in the center
When placing the battery
pack in the tool, be sure that the
raised rib on battery pack aligns with the groove inside the Right-Angle Impact
Driver and that the latches snap into place properly. Improper attachment of the
battery pack can cause damage to internal components.
If the charger detects a problem with the battery, the battery may be defective:
the red LED will begin flashing and the green LED will be off.
2.
(forward/center
Align the raised rib on the battery pack with the grooves in the Right-Angle
Impact Driver, and then insert the battery pack into the tool.
_L. CAUTION:
DEFECTIVE BATTERY
If registering as defective, remove and reinsert the battery pack in the
charger. If the LED status reads "defective" a second time, try charging
different battery pack.
2.
of rotation
NOTE: Make sure that the latch on the battery pack snaps into place and that
the battery pack is secured to the tool before beginning operation.
If the battery pack is below the normal temperature range, the red LED
will illuminate and the green LED will be off. When the battery warms to a
temperature of more than 32°F (0°C), the charger will automatically
begin
charging.
1.
direction
position.
TO DETACH BATTERY PACK (Fig, 4)
1. Lock the trigger switch on the Right-Angle
direction of rotation
Lock position.
a
2.
Depress the battery release buttons
pack to release the battery pack.
3.
Pull the battery pack out and remove it from the tool.
battery
the charger may be
Impact Driver by placing the
(forward / center lock/reverse)
selector in the Center
_lk WARNING:
If the battery pack is being charged within a normal surrounding temperature
range (32°F to 104°F), the green LED will begin flashing and the red LED will be
off. The battery pack will reach a full charge in 30 minutes.
BATTERY FULL
If the battery pack is within normal temperature range, the green LED will
illuminate and the red LED will be off. The battery pack is fully charged and
ready to use. The battery pack will fully charge, but will not overcharge, if left on
the charger.
Fig. 4
NOTE: The charger may
become warm with several
continuous charge cycles. This
is part of the normal operation
of the charge. Charge in a well
ventilated area.
TRIGGER
SWITCH
(Fig, 5)
To turn it OFF, release the
trigger switch.
SPEED (Fig,5)
The variable-speed
trigger
switch delivers higher speed
with increased trigger pressure
and lower speed with decreased
trigger pressure.
condition.
Therefore,
the
always be locked when the tool is not in use
Fig. 5
To turn the 12V Right-Angle
Impact Driver ON, depress the
trigger switch.
VARIABLE
on the both sides of the battery
Battery tools are always in operating
direction-of-rotation
selector should
or when carrying it your side.
CHARGING
located
Variable-speed
trigger switch
Directionof-rotation
selector
(Forward/
Center
Lock/
Reverse
TO ATTACH BATTERY PACK
(Fig. 4)
1.
17562
Lock the trigger switch on
the Right-Angle Impact
Driver by placing the
ManuaLRevised_$0
0607
Page 14
17562
ManuaLRevised_10
0607
Page 15
DIRECTION-OF-ROTATION
REVERSE) (Fig. 5)
SELECTOR
(FORWARD/CENTER
LOCK/
LED WORKLIGHT
(Fig. 7)
Fig. 7
Position the direction-of-rotation
rotation.
selector to the left of the tool for forward
The LED worklight, located on
the front of the 12V Right-Angle
Impact Driver, will illuminate
when the trigger switch is
depressed.
2.
Position the direction-of-rotation
rotation.
selector to the right of the tool for reverse
This provides additional light on
the surface of the workpiece for
operation in lower-light areas.
3.
Setting the switch in the OFF (center lock) position
possibility of accidental starting when not in use.
_i,
CAUTION:
The direction of bit rotation is reversible and is controlled by a selector located
above the trigger switch. With the Right-Angle Impact Driver held in normal
operating position:
1.
To prevent gear damage,
Impact Driver to come to a complete
rotation.
The LED worklight will turn
off when the trigger switch is
released.
helps reduce the
always allow the 12V Right-Angle
stop before changing
the direction
INSTALLING
of
1.
NOTE: The 12V Right-Angle Impact Driver will not run unless the direction
rotation selector is engaged fully to the left or right.
ELECTRIC
of
BRAKE
2.
The green LED on the
FuelGauge indicates that the
battery is fully charged.
The orange LED on the
FuelGauge indicates that the
battery has used approximately
one half of its charge
ManuaLRevised_$O
0607
Fig. 8
With one hand, pull the
sleeve toward the front of
3.
With the other hand, insert
a 1/4-in. shank bit into the
hexagonal
retainer.
Fig. 6
4.
_i,
FuelGauge
hole in the bit
Release the sleeve and
check that it returns to its
original
tP
position.
WARNING:
correctly
If the sleeve does not return to its original
installed.
WARNING:
Retry until the bit is properly
Use protective
position,
the bit is not
installed.
gloves when removing
the bit from the tool, or
first allow the bit to cool down. The bit may be hot after prolonged
use.
J.z/
C
REMOVING
The red LED on the FuelGauge
indicates the battery pack
is depleted and needs to be
charged.
17562
Lock the trigger switch by
placing the direction-ofrotation selector in the OFF
the tool, and hold it in place.
(Fig. 6)
This tool is equipped with a
FuelGauge that indicates the
battery pack charge level.
BITS (Fig. 8)
(center) position.
To stop the 12V Right-Angle Impact Driver, release the trigger switch and
allow the tool to come to a complete stop. The electric brake quickly stops the
rotation. This feature engages automatically
when you release the trigger switch.
FuelGauge
LED Worklight
Page 16
BITS (Fig. 8)
1.
Lock the trigger switch by placing the direction-of
OFF (center) position.
2.
Pull the sleeve towards
3.
Remove the bit from the hexagonal
4.
Release the sleeve.
17562
ManuaLRevised_lO
0607
rotation
selector
in the
the front of the tool, and hold it in place.
hole in the bit retainer.
Page 17
TIGHTENING SCREWS
NUTS (Fig. 9)
1.
Install the correct
AND
Fig. 9
\
I_ f-'l I11i 11 I-'I1[*']=1
A
All WARNING: To avoid serious personal injury, always remove the battery
pack from the tool when cleaning or performing any maintenance.
bit.
2. Apply just enough pressure
to keep the bit engaged on
the screw or nut.
WARNING: When servicing, use only identical Craftsman
Use of any other parts may create a hazard or cause product
replacement
damage.
parts.
&
3.
Position the direction-ofrotation selector to the left of
the tool for forward rotation.
4.
Apply minimal pressure to
the trigger switch initially.
Increase the speed only
when full control can be
maintained.
_i
WARNING:
_. WARNING:
It is not recommended
to use compressed
dry air as a cleaning
method for the Right-Angle Impact Driver. If cleaning with compressed air is the
only method available, always wear safety goggles or safety glasses with side
shields when using compressed air to clean the tool. If the operation is dusty,
also wear a dust mask.
GENERAL MAINTENANCE
Do not over-tighten,
as the force of the 12V Right-Angle
Driver can break the fastener. Keep the 12V Right-Angle Impact Driver
angle to the fastener to avoid damaging the fastener head.
LOOSENING
SCREWS
at a right
Install the correct
bit.
2.
Apply just enough pressure
to keep the bit engaged on
the screw or nut.
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible
to damage from various types of commercial solvents and may be damaged by
their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
_,
WARNING:
Do not at any time let brake fluids,
gasoline,
petroleum-
based products,
penetrating
oils, etc. to come in contact with plastic parts.
Chemicals
can damage, weaken or destroy plastic which may result in
serious personal injury.
AND NUTS (Fig. 10)
1.
3.
Impact
[ Fig. 10
/
WARNING:
When servicing,
use only identical
Craftsman
replacement
parts.
Use of any other parts may create a hazard or cause product damage. To ensure
safety and reliability, all repairs should be performed by a qualified service
technician at a Sears Service Center.
Position the direction-ofrotation selector to the
right of the tool for forward
rotation.
4.
17562
Apply minimal pressure to
the trigger switch initially.
Increase the speed only
when full control can be
maintained.
ManuaLRevised_$0
0607
Page 18
17562
ManuaLRevised_10
0607
Page 19
BATTERIES:
The battery pack is equipped with Lithium-Ion
duration of use from each charge will depend
rechargeable batteries. The
on the type of work performed.
The batteries in this tool have been designed to provide maximum troublefree life. Like all batteries, they will eventually wear out. Do not disassemble
the battery pack or attempt to replace the batteries. Handling of the batteries,
especially when wearing rings and jewelry, could result in a serious burn.
To obtain the longest possible
operator's manual.
•
battery
CAUSE
The tool does not work
Battery
pack storage
SOLUTION
is depleted
Charge the battery
Sleeve is not released
Release the sleeve
Bit does not fit the sleeve
Use a 1/4" shank bit
Make sure that the cooling
vents are free from dust
and obstacles
Clean clear vents.
Do not cover vents
Bit cannot be installed
and follow this
Motor overheating
It is good practice to unplug the Charger/Adapter
Ion battery pack when not in use.
For Lithium-Ion
•
battery life, read, understand
PROBLEM
and remove the Lithium-
during operation
longer than 30 days:
Store the Lithium-Ion battery pack where the
temperature is below 80°F (26°C) and free of
moisture.
Store Lithium-Ion battery
charged condition.
packs in a 30%-50%
After every six months of storage,
the Lithium-Ion battery pack.
fully charge
Exterior may be cleaned with a cloth or soft
non-metallic brush.
BATTERY
PACK REMOVAL
AND PREPARATION
FOR RECYCLING
To preserve natural resources, please recycle or dispose of batteries properly.
This product contains lithium-ion batteries. Local, state, or federal laws may
prohibit disposal of lithium-ion batteries in ordinary trash. Consult your local
waste authority for information regarding available recycling and/or disposal
options.
WARNING:
Upon removal
of the battery pack for disposal
or recycling,
cover the battery pack's terminals with heavy-duty adhesive tape. Do not
attempt to destroy or disassemble the battery pack or remove any of its
components.
Lithium-Ion batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects and/or body parts, as
short circuit may result. Keep away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
17562
ManuaLRevised_$0
0607
Page 20
17562
ManuaLRevised_i0
0607
Page 2i
12.0-VOLT LITHIUM-ION
MODEL NO. 320. 17562
CORDLESS
RIGHT-ANGLE
IMPACT
DRIVER
The Model Number will be found on the Nameplate attached to the handle of the
Right-Angle Impact Driver. Always mention the Model Number when ordering
parts for this tool.
1
2730137000
DC Motor
1
2
3123113000
LED Cover
1
3
3123120000
Light Guide Pole
1
Exloded
4
3125334000
F/R Button
1
5
3125534000
Switch Trigger
1
6
3321025000
Left Housing
7
3321026000
Right Housing Assy
8
3402298000
Contact
9
3421092000
Left Gear Case
1
10
3421093000
Right Gear Case
1
11
3421145000
Bottom Support
1
12
3520410000
Gear
1
13
3520555000
Pinion
1
14
3550606000
Bush
1
15
3551501000
Impact Block
1
16
3551502000
Spindle
1
17
3551503000
Spindle
1
18
3551511000
Bevel Gear
1
19
3551528000
Bevel Gear
1
20
3551582000
Bush
1
21
3660177000
Spring
1
22
3660403000
Spring
1
23
3660437000
Spring
1
24
4890699000
PCB Assembly
1
25
5610012000
Tapping
Screw
2
26
5610013000
Tapping
Screw
7
27
5620006000
Hexagon Socket Screw
9
28
5620033000
Screw
2
29
5650003000
Spring Washer
7
17562
View
ManuaLRevised_lO
0607
Page 22
17562
ManuaLRevised_lO
0607
Assy
Receptacle
1
1
ASSY
1
Page 23
_o_nul
17562
30
5650192000
Washer
1
31
5650254000
Washer
2
32
5650349000
Washer
1
33
5650366000
Washer
2
34
5660035000
Circlips For Shaft
1
35
5690207000
Washer
1
36
5690222000
Washer
1
37
5700003000
Ball Bearing
2
38
5700044000
Steel Ball
23
39
5700053000
Needle Bearing
1
40
5700176000
Ball Bearing
1
41
5700178000
Steel Ball
2
42
5700226000
Steel Ball
2
ManuaLRevised_lO
0607
Page 24
17562
ManuaLRevised_lO
0607
Page 25
_o_nul
17562
ManuaLRevised_lO
0607
_o_nul
Page 26
17562
ManuaLRevised_lO
0607
Page 27
Your Home
For troubleshooting, product manuals and expert advice:
managemylife
www.managemylife.com
For repair- in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
(1-800-469-4663)
Ca, anytime,dayor night
(U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of the nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
www.sears,com
1-800-469-4663 (Canada)
www.sears,ca
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR®
(1-888-784-6427)
www.sears.com
1-800-361-6665 (Canada)
Au Canada pour service en franc_ais:
1-800-LE-FOYERMc
(1-800-533-6937)
www.sears.ca
Se llrS
TM
Trademark
/
Trademark
of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries
® Marca Registrada
/ TM Marca de Ffibrica de KCD IP, LLC en Estados
Unidos, o Sears
Brands,
LLC in otros paises
_4CMarque de commerce
/ _4DMarque d6pos6e de Sears Brands, LLC
® Registered