Brocade Communications Systems 5300 Technical data

53-1000858-02
July 18, 2008
Brocade 5300
Hardware Reference Manual
Copyright © 2008 Brocade Communications Systems, Inc. All Rights Reserved.
Brocade, Fabric OS, File Lifecycle Manager, MyView, and StorageX are registered trademarks and the Brocade B-wing symbol,
DCX, and SAN Health are trademarks of Brocade Communications Systems, Inc., in the United States and/or in other countries.
All other brands, products, or service names are or may be trademarks or service marks of, and are used to identify, products or
services of their respective owners.
Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning
any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to
this document at any time, without notice, and assumes no responsibility for its use. This informational document describes
features that may not be currently available. Contact a Brocade sales office for information on feature and product availability.
Export of technical data contained in this document may require an export license from the United States government.
The authors and Brocade Communications Systems, Inc. shall have no liability or responsibility to any person or entity with
respect to any loss, cost, liability, or damages arising from the information contained in this book or the computer programs that
accompany it.
The product described by this document may contain “open source” software covered by the GNU General Public License or other
open source license agreements. To find-out which open source software is included in Brocade products, view the licensing
terms applicable to the open source software, and obtain a copy of the programming source code, please visit
http://www.brocade.com/support/oscd.
Brocade Communications Systems, Incorporated
Corporate Headquarters
Brocade Communications Systems, Inc.
1745 Technology Drive
San Jose, CA 95110
Tel: 1-408-333-8000
Fax: 1-408-333-8101
Email: info@brocade.com
Asia-Pacific Headquarters
Brocade Communications Singapore Pte. Ltd.
9 Raffles Place
#59-02 Republic Plaza 1
Singapore 048619
Tel: +65-6538-4700
Fax: +65-6538-0302
Email: apac-info@brocade.com
European and Latin American Headquarters
Brocade Communications Switzerland Sàrl
Centre Swissair
Tour A - 2ème étage
29, Route de l'Aéroport
Case Postale 105
CH-1215 Genève 15
Switzerland
Tel: +41 22 799 56 40
Fax: +41 22 799 56 41
Email: emea-info@brocade.com
Document History
The following table lists all versions of the Brocade 5300 Hardware Reference Manual.
Document Title
Publication Number
Summary of Changes
Date
Brocade 5300 Hardware Reference Manual
53-1000858-01
New document
March 2008
Brocade 5300 Hardware Reference Manual
53-1000858-02
Document update
July 2008
Contents
About This Document
In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
How this document is organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Supported hardware and software . . . . . . . . . . . . . . . . . . . . . . . . . . vii
What’s new in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Text formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Command syntax conventions . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Notes, cautions, and warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Key terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Notice to the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Brocade resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Other industry resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Getting technical help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Chapter 1
Brocade 5300 Introduction
In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Brocade 5300 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Port side of the Brocade 5300. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Non-port side of the Brocade 5300. . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Ports on Demand license . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Brocade Inter-Switch Link (ISL) Trunking . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2
Brocade 5300 Installation and Configuration
In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Items included with the Brocade 5300 . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation and safety considerations. . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Environmental considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cabinet considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Recommendations for cable management . . . . . . . . . . . . . . . . . 8
Items required for installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing a standalone Brocade 5300 . . . . . . . . . . . . . . . . . . . . . . . . 9
Brocade 5300 Hardware Reference Manual
58-1000858-02
iii
Cabinet installation for a Brocade 5300 . . . . . . . . . . . . . . . . . . . . . . 10
Brocade 5300 configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Providing power to the switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Creating a serial connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Switch IP address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Date and time settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 3
Brocade 5300 Operation
In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Powering the Brocade 5300 on and off . . . . . . . . . . . . . . . . . . . . . . 17
LED activity interpretation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Brocade 5300 LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LED locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
LED patterns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
POST and boot specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
POST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Boot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Interpreting POST results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Brocade 5300 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Installing an SFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Field Replaceable Units (FRUs). . . . . . . . . . . . . . . . . . . . . . . . . . 25
Brocade 5300 Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Appendix A
Brocade 5300 Specifications
In this appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Switch components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Weight and physical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Facility requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Power supply specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Environmental requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
General specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Data transmission ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Memory specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Fibre Channel port specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Serial port specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
iv
Brocade 5300 Hardware Reference Manual
58-1000858-02
Regulatory compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
FCC warning (US only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
MIC statement (Republic of Korea) . . . . . . . . . . . . . . . . . . . . . . 33
VCCI statement Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Power cords (Japan Denan). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
BSMI statement (Taiwan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
CE statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Canadian requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Laser compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
RTC battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Electrical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Regulatory certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Environmental regulation compliance . . . . . . . . . . . . . . . . . . . . . . . . 35
China RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Index
Brocade 5300 Hardware Reference Manual
58-1000858-02
v
vi
Brocade 5300 Hardware Reference Manual
58-1000858-02
About This Document
In this chapter
• How this document is organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
• Supported hardware and software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
• What’s new in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
• Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
• Notice to the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
• Additional information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
• Getting technical help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
• Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
How this document is organized
This document is organized to help you find the information that you want as quickly and easily as
possible.
The document contains the following components:
• Chapter 1, “Brocade 5300 Introduction,” provides an overview of the Business Continuity
Manager switch, a feature list, and a look at the appearance of the switch.
• Chapter 2, “Brocade 5300 Installation and Configuration,” provides the information needed to
install the switch into your network.
• Chapter 3, “Brocade 5300 Operation” discusses the day-to-day operational procedures for
using the switch.
• Appendix A, “Brocade 5300 Specifications”provides tables of physical, environmental, and
general specifications, helpful for quick lookup.
• The index points you to the exact pages on which specific information is located.
Supported hardware and software
Although many different software and hardware configurations are tested and supported by
Brocade Communications Systems, Inc. for Fabric OS v6.1.0, documenting all possible
configurations and scenarios is beyond the scope of this document.
This document is specific to the Product Name and Fabric OS v6.1.0. To obtain information about a
Fabric OS version other than v6.1.0, see the documentation specific to that OS version.
Brocade 5300 Hardware Reference Manual
58-1000858-02
vii
What’s new in this document
Corrections have been made to the original document.
Document conventions
This section describes text formatting conventions and important notice formats used in this
document.
Text formatting
The narrative-text formatting conventions that are used are as follows:
bold text
Identifies command names
Identifies the names of user-manipulated GUI elements
Identifies keywords and operands
Identifies text to enter at the GUI or CLI
italic text
Provides emphasis
Identifies variables
Identifies paths and Internet addresses
Identifies document titles
code text
Identifies CLI output
Identifies command syntax examples
For readability, command names in the narrative portions of this guide are presented in mixed
lettercase: for example, switchShow. In actual examples, command lettercase is often all
lowercase. Otherwise, this manual specifically notes those cases in which a command is case
sensitive.
Command syntax conventions
Command syntax in this manual follows these conventions:
viii
command
Commands are printed in bold.
--option, option
Command options are printed in bold.
-argument, arg
Arguments.
[]
Optional element.
variable
Variables are printed in italics. In the help pages, values are underlined or
enclosed in angled brackets < >.
...
Repeat the previous element, for example “member[;member...]”
value
Fixed values following arguments are printed in plain font. For example,
--show WWN
|
Boolean. Elements are exclusive. Example: --show -mode egress | ingress
Brocade 5300 Hardware Reference Manual
58-1000858-02
Notes, cautions, and warnings
The following notices and statements are used in this manual. They are listed below in order of
increasing severity of potential hazards.
NOTE
A note provides a tip, guidance or advice, emphasizes important information, or provides a reference
to related information.
ATTENTION
An Attention statement indicates potential damage to hardware or data.
CAUTION
A Caution statement alerts you to situations that can be potentially hazardous to you.
DANGER
A Danger statement indicates conditions or situations that can be potentially lethal or extremely
hazardous to you. Safety labels are also attached directly to products to warn of these conditions
or situations.
Key terms
For definitions specific to Brocade and Fibre Channel, see the Brocade Glossary.
For definitions of SAN-specific terms, visit the Storage Networking Industry Association online
dictionary at:
http://www.snia.org/education/dictionary
Notice to the reader
This document may contain references to the trademarks of the following corporations. These
trademarks are the properties of their respective companies and corporations.
These references are made for informational purposes only.
Corporation
Referenced Trademarks and Products
IBM Corporation
IBM, FICON, PowerPC
Additional information
This section lists additional Brocade and industry-specific documentation that you might find
helpful.
Brocade 5300 Hardware Reference Manual
58-1000858-02
ix
Brocade resources
To get up-to-the-minute information, join Brocade Connect. It’s free! Go to http://www.brocade.com
and click Brocade Connect to register at no cost for a user ID and password.
For practical discussions about SAN design, implementation, and maintenance, you can obtain
Building SANs with Brocade Fabric Switches through:
http://www.amazon.com
For additional Brocade documentation, visit the Brocade SAN Info Center and click the Resource
Library location:
http://www.brocade.com
Release notes are available on the Brocade Connect Web site and are also bundled with the Fabric
OS firmware.
Other industry resources
• White papers, online demos, and data sheets are available through the Brocade Web site at
http://www.brocade.com/products/software.jhtml.
• Best practice guides, white papers, data sheets, and other documentation is available through
the Brocade Partner Web site.
For additional resource information, visit the Technical Committee T11 Web site. This Web site
provides interface standards for high-performance and mass storage applications for Fibre
Channel, storage management, and other applications:
http://www.t11.org
For information about the Fibre Channel industry, visit the Fibre Channel Industry Association Web
site:
http://www.fibrechannel.org
Getting technical help
Contact your switch support supplier for hardware, firmware, and software support, including
product repairs and part ordering. To expedite your call, have the following information available:
1. General Information
•
•
•
•
•
Switch model
Switch operating system version
Error numbers and messages received
supportSave command output
Detailed description of the problem, including the switch or fabric behavior immediately
following the problem, and specific questions
• Description of any troubleshooting steps already performed and the results
• Serial console and Telnet session logs
• syslog message logs
x
Brocade 5300 Hardware Reference Manual
58-1000858-02
2. Switch Serial Number
The switch serial number and corresponding bar code are provided on the serial number label,
as illustrated below.:
*FT00X0054E9*
FT00X0054E9
The serial number label is located as follows:
• Brocade 200E—On the non-port side of the chassis
• Brocade 300, 4100, 4900, 5100, 5300, 7500, and Brocade Encryption Switch—On the
switch ID pull-out tab located inside the chassis on the port side on the left
• Brocade 5000—On the switch ID pull-out tab located on the bottom of the port side of the
switch
• Brocade 7600—On the bottom of the chassis
• Brocade 48000—Inside the chassis next to the power supply bays
• Brocade DCX—On the bottom right on the port side of the chassis
3. World Wide Name (WWN)
Use the wwn command to display the switch WWN.
If you cannot use the wwn command because the switch is inoperable, you can get the WWN
from the same place as the serial number, except for the Brocade DCX. For the Brocade DCX,
access the numbers on the WWN cards by removing the Brocade logo plate at the top of the
non-port side of the chassis.
Document feedback
Quality is our first concern at Brocade and we have made every effort to ensure the accuracy and
completeness of this document. However, if you find an error or an omission, or you think that a
topic needs further development, we want to hear from you. Forward your feedback to:
documentation@brocade.com
Provide the title and version number of the document and as much detail as possible about your
comment, including the topic heading and page number and your suggestions for improvement.
Brocade 5300 Hardware Reference Manual
58-1000858-02
xi
xii
Brocade 5300 Hardware Reference Manual
58-1000858-02
Chapter
1
Brocade 5300 Introduction
In this chapter
• Brocade 5300 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Port side of the Brocade 5300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Non-port side of the Brocade 5300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Ports on Demand license . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Brocade Inter-Switch Link (ISL) Trunking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
3
4
5
Brocade 5300 overview
The Brocade 5300 is an 80-port 1, 2, 4, or 8 Gbps Fibre Channel switch that delivers Brocade sixth
generation ASIC technology and architecture for Fibre Channel Storage Area Networks (SANs). The
Brocade 5300 is designed for the needs of enterprise environments that require a high-port
footprint for port aggregation.
With its high auto-sensing port count and ports-on-demand flexibility, the Brocade 5300 is an ideal
solution as a fan-out switch from a director core, or as the core switch in a fabric. The Brocade
5300 satisfies demanding Reliability, Availability, and Serviceability (RAS), performance and
scalability requirements of an enterprise switch while delivering interoperability and ease-of-use
advantages found only in the Brocade product family. The Brocade 5300 is the latest enterprise
offering from the Brocade family of entry-to-enterprise products, and offers the following features
and capabilities:
•
•
•
•
•
•
Up to 80 auto-sensing ports of high-performance 8 Gbps technology in a single domain.
Ports On Demand scaling from 48 to 64 or 80 ports.
Full 1:1 subscription on all 80 ports at 8 Gbps.
1, 2, 4 and 8 Gbps auto-sensing Fibre Channel switch and router ports.
FICON and FICON Control Unit Port ready.
Fibre Channel Routing (FCR) service, which provides improved scalability and fault isolation,
along with multi-vendor interoperability through the optional Integrated Routing license.
• Two hot-swappable, redundant power supply FRUs.
• Three hot-swappable fan FRUs in an N+1 configuration to provide hardware-redundant cooling.
• Universal ports that self-configure as E, F, M or FL ports. Ex_Ports are activated on a per port
basis with the optional Integrated Routing license.
• An RJ45 Ethernet management port, in conjunction with EZSwitchSetup, that supports switch
IP address discovery and configuration, eliminating the need to attach a serial cable to
configure the switch IP address and greatly increasing the ease of use.
• USB port that provides storage for firmware updates, output of the supportSave command and
storage for configuration uploads and downloads.
Brocade 5300 Hardware Reference Manual
58-1000858-02
1
1
Port side of the Brocade 5300
• A system motherboard that features a Freescale MPC8548 Reduced Instruction Set Computer
(RISC) CPU running at 1.3 GHz with integrated peripherals, and that provides high performance
with low power consumption.
• Inter-Switch Link (ISL) Trunking (licensable), which allows up to eight ports (at 1, 2, 4, or 8 Gbps
speeds) between a pair of switches combined to form a single, logical ISL with a speed of up to
64 Gbps (128 Gbps full duplex) for optimal bandwidth utilization and load balancing.
• Dynamic Path Selection (DPS), which optimizes fabric-wide performance and load balancing by
automatically routing data to the most efficient available path in the fabric.
• Rack-mount design using existing rail kits (fixed, sliding, and mid-mount/Telco rail kits) on a
19” EIA rack.
• Industry-leading extended distance support, which enables native Fibre Channel extension
greater than 590 km (366 miles).
• Brocade Small Form-Factor Pluggable (SFP) or SFP+ optical transceivers that support any
combination of Short Wavelength (SWL), Long Wavelength (LWL), or Extended Long
Wavelength (ELWL) optical media among the switch ports.
• Unicast, multicast (255 groups), and broadcast data traffic type support.
• Brocade Fabric Operating System (FOS), which delivers distributed intelligence throughout the
network and enables a wide range of value-added applications including Brocade Advanced
Web Tools and Brocade Zoning. Optional Fabric Services include: Adaptive Networking with
QoS, Brocade Extended Fabrics, Brocade Enhanced Group Management, Brocade Fabric
Watch, ISL Trunking, Integrated Routing, and End-to-End Performance Monitoring (APM).
• Port-to-port latency minimized to 2100 nanoseconds through the use of cut-through frame
routing at 8 Gbps.
• Extensive diagnostics and system-monitoring capabilities for enhanced high Reliability,
Availability, and Serviceability (RAS)
• The Brocade EZSwitchSetup wizard that makes SAN configuration a three-step point-and-click
task.
Port side of the Brocade 5300
The port side of the Brocade 5300 includes the system status LED, console port, Ethernet port and
LEDs, USB port, and Fibre Channel ports and the corresponding port status LEDs.
Figure 1 shows the port side of the Brocade 5300.
2
Brocade 5300 Hardware Reference Manual
58-1000858-02
Non-port side of the Brocade 5300
1
1
2
3
11
FIGURE 1
4
5
6
12
7
8
9
10
13
14
15
16
Port side view of the Brocade 5300
1
Brocade 5300
9
FC ports 16-23
2
Switch ID pull-out tab
10 FC ports 24-31
3
System status LED (top)
11 FC ports 32-38
System power LED (bottom)
12 FC ports 40-47
4
Console port
13 FC ports 48-55
5
Ethernet port
14 FC ports 56-63
6
USB port
15 FC ports 64-71
7
FC ports 0-7
16 FC ports 72-79
8
FC ports 8-15
Non-port side of the Brocade 5300
Figure shows the non-port side of the Brocade 5300, which contains the power supplies (including
the AC power receptacle and AC power switch) and fans.
Brocade 5300 Hardware Reference Manual
58-1000858-02
3
1
Ports on Demand license
1
2
3
FIGURE 2
4
5
6
7
Non-port side of the Brocade 5300
1
Brocade 5300
5
Fan assembly #2
2
Non-port side of switch
6
Fan assembly #1
3
Power supply #2
7
Power supply #1
4
Fan assembly #3
Ports on Demand license
The Brocade 5300 has 80 ports. By default, ports 0-47 are enabled. As your needs increase, you
can activate unlicensed ports by purchasing and installing the Brocade Ports on Demand (POD)
optional licensed product. After it has been installed, the license appears in the licenseShow
command output as Ports on Demand license.
To install a Ports on Demand license, you can either use the supplied license key or generate a
license key. Typically the switch is shipped with a paper pack that specifies the transaction key to
use with the Software License Keys link. Use this transaction key on the Brocade Web site at
www.brocade.com/licensekeys and follow the instructions to generate the key. You can also use
this site to generate other license keys for your switch.
4
Brocade 5300 Hardware Reference Manual
58-1000858-02
Brocade Inter-Switch Link (ISL) Trunking
1
After you have installed the license keys, you must enable the ports. You can do so without
disrupting switch operation by using the portEnable command on each port individually.
Alternatively, you can disable and re-enable the switch to activate all ports simultaneously.
For detailed information on enabling additional ports using the Ports on Demand license, refer to
the Fabric OS Administrator’s Guide.
Brocade Inter-Switch Link (ISL) Trunking
Brocade ISL Trunking is optional software that allows you to create trunking groups of ISLs between
adjacent switches. Each eight port group on the Brocade 5300 can be used as a trunking group.
For more information about Brocade ISL Trunking, see the Fabric OS Administrator’s Guide.
Brocade 5300 Hardware Reference Manual
58-1000858-02
5
1
6
Brocade Inter-Switch Link (ISL) Trunking
Brocade 5300 Hardware Reference Manual
58-1000858-02
Chapter
Brocade 5300 Installation and Configuration
2
In this chapter
• Items included with the Brocade 5300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
• Installation and safety considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
• Installing a standalone Brocade 5300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
• Cabinet installation for a Brocade 5300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
• Brocade 5300 configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Items included with the Brocade 5300
The following items are included with the standard shipment of the Brocade 5300. When you open
the Brocade 5300 packaging, verify that these items are included in the package and that no
damage has occurred during shipping:
• The Brocade 5300 switch, containing three fan assemblies and two power supplies
• One accessory kit, containing the following items:
• Serial cable with an RJ-45 connector
• 6 ft. Power Cord
• Rubber feet, required for setting up the switch as a standalone unit
• Brocade Family Doc CD
• Brocade 5300 QuickStart Guide
• EZSwitch Setup CD
Installation and safety considerations
You can install the Brocade 5300 switch in the following ways:
1. As a standalone unit on a flat surface.
2. In an EIA cabinet using a fixed-rail rack mount kit. The optional fixed-rail rack mount kit can
be ordered from your switch retailer.
3. In an EIA cabinet using an optional slide-rail rack mount kit. The optional slide-rail rack
mount kit can be ordered from your switch retailer.
4. In an EIA cabinet using an optional mid-mount rack kit for switches. The optional
mid-mount rack kit for switches can be ordered from your switch retailer.
Brocade 5300 Hardware Reference Manual
58-1000858-02
7
2
Installation and safety considerations
Electrical considerations
To install and operate the switch successfully, ensure the following:
• The primary outlet is correctly wired, protected by a circuit breaker, and grounded in
accordance with local electrical codes.
• The supply circuit, line fusing, and wire size are adequate, as specified by the electrical
rating on the switch nameplate.
• The power supply standards provided in Table 6, “Power Supply Specifications” on
page 28 are met.
Environmental considerations
For successful installation and operation of the switch, ensure that the following environmental
requirements are met:
• At a minimum, adequate cooling requires that you install the switch with the non-port side,
which contains the air intake vents, facing the cool-air aisle.
• All equipment in the rack should force air in the same direction to avoid intake of exhaust
air.
• A maximum of 102 cubic meters/hour (60 cubic feet/minute) and a minimum of 74.8
cubic meters/hour (44 cubic feet/minute) of air flow is available to the air intake vents on
the non-port side of the switch.
• The ambient air temperature does not exceed 40° C (104° F) while the switch is operating.
Cabinet considerations
For successful installation and operation of the switch in a cabinet, ensure the following cabinet
requirements are met:
• The cabinet must be a standard EIA cabinet.
• Plan a cabinet space that is one rack unit (1U) high; 4.45 cm (1.75 inches) high and 48.3
cm (19 inches) wide.
• Ground all equipment in the cabinet through a reliable branch circuit connection and
maintain ground at all times. Do not rely on a secondary connection to a branch circuit,
such as a power strip.
• Ensure that airflow and temperature requirements are met on an ongoing basis,
particularly if the switch is installed in a closed or multicabinet assembly.
• Verify that the additional weight of the switch does not exceed the cabinet’s weight limits
or unbalance the cabinet in any way.
• Secure the cabinet to ensure stability in case of unexpected movement, such as an
earthquake.
Recommendations for cable management
The minimum bend radius for a 50 micron cable is 2 inches under full tensile load and 1.2 inches
with no tensile load.
8
Brocade 5300 Hardware Reference Manual
58-1000858-02
Installing a standalone Brocade 5300
2
Cables can be organized and managed in a variety of ways, for example, using cable channels on
the sides of the cabinet or patch panels to minimize cable management. Following is a list of
recommendations:
NOTE
You should not use tie wraps with optical cables because they are easily overtightened and can
damage the optic fibers.
• Plan for rack space required for cable management before installing the switch.
• Leave at least 1 m (3.28 ft) of slack for each port cable. This provides room to remove and
replace the switch, allows for inadvertent movement of the rack, and helps prevent the
cables from being bent to less than the minimum bend radius.
• If you are using Brocade ISL Trunking, consider grouping cables by trunking groups. The
cables used in trunking groups must meet specific requirements, as described in the
Fabric OS Administrator’s Guide.
• For easier maintenance, label the fiber optic cables and record the devices to which they
are connected.
• Keep LEDs visible by routing port cables and other cables away from the LEDs.
• Use hook and loop style straps to secure and organize fiber optic cables.
Items required for installation
The following items are required for installing, configuring, and connecting the Brocade 5300 for
use in a network and fabric:
•
•
•
•
•
•
Workstation with an installed terminal emulator, such as HyperTerminal
Unused IP address and corresponding subnet mask and gateway address
Serial cable (provided)
Ethernet cable
SFPs and compatible cables, as required
Access to an FTP server for backing up the switch configuration (optional)
Installing a standalone Brocade 5300
Perform this task to install the Brocade 5300 as a standalone unit.
1. Unpack the Brocade 5300 and verify the items listed on “Items included with the Brocade
5300” on page 7. Verify the items are present and undamaged.
2. Apply the adhesive rubber feet. Applying the rubber feet onto the switch helps prevent the
switch from sliding off the supporting surface.
a.
Clean the indentations at each corner of the bottom of the switch to ensure that they are
free of dust or other debris that might lessen the adhesion of the feet.
b.
With the adhesive side against the chassis, place one rubber foot in each indentation and
press into place.
3. Place the switch on a flat, sturdy surface.
4. Provide power to the switch as described in “Providing power to the switch” on page 10.
Brocade 5300 Hardware Reference Manual
58-1000858-02
9
2
Cabinet installation for a Brocade 5300
ATTENTION
Do not connect the switch to the network until the IP address is correctly set. For instructions on how
to set the IP address, see “Brocade 5300 configuration”
Cabinet installation for a Brocade 5300
Follow the installation instructions shipped with the appropriate rack mount kit:
• To install the switch into a fixed-rail rack, refer to the Fixed Rack Mount Kit Installation
Procedure.
• To install the switch into a slide-rail rack, refer to the Slide Rack Mount Kit Installation
Procedure.
• To install the switch into mid-mount rack, refer to the Mid-Mount Rack Mount Kit (Switch)
Installation Procedure.
Brocade 5300 configuration
Once you have set up the Brocade 5300 in a rack or as a standalone switch, it is time to give it
power and a basic configuration. If you are going to use the Brocade 5300 in a single-switch setup,
you can use EZSwitchSetup to complete the basic configuration.
See the EZSwitchSetup CD, included with the Brocade 5300 for more information. You can also
use the Brocade 5300 Quick Start Guide.
If you do not want to use EZSwitch Setup, follow the instructions in the rest of this section.
Providing power to the switch
Perform the following steps to provide power to the Brocade 5300.
1. Connect the power cords to both power supplies, and then to power sources on separate
circuits to protect against AC failure. Ensure that the cords have a minimum service loop of 6
in. available and are routed to avoid stress.
2. Power on the power supplies by flipping both AC switches to the “1” symbol. The power supply
LEDs display amber until POST is complete, and then change to green. The switch usually
requires from 1 to 3 min to boot and complete POST.
ATTENTION
Power is supplied to the switch as soon as the first power supply is connected and turned on.
3. After POST is complete, verify that the switch power and status LEDs on the left of the port side
of the switch are green.
Creating a serial connection
You will perform all configuration tasks in this guide using a serial connection.
Complete the following steps to create a serial connection to the switch.
10
Brocade 5300 Hardware Reference Manual
58-1000858-02
Brocade 5300 configuration
2
1. Connect the serial cable to the serial port on the switch and to an RS-232 serial port on
the workstation.
If the serial port on the workstation is RJ-45 instead of RS-232, remove the adapter on the end
of the serial cable and insert the exposed RJ-45 connector into the RJ-45 serial port on
the workstation.
2. Open a terminal emulator application (such as HyperTerminal on a PC, or TERM, TIP, or Kermit
in a UNIX environment), and configure the application as follows:
• In a Windows environment:
Parameter
Value
Bits per second
9600
Databits
8
Parity
None
Stop bits
1
Flow control
None
• In a UNIX environment, enter the following string at the prompt:
tip /dev/ttyb -9600.
If ttyb is already in use, use ttya instead and enter the following string at the prompt:
tip /dev/ttya -9600
Switch IP address
You can configure the Brocade 5300 with a static IP address, or you can use a DHCP (Dynamic
Host Configuration Protocol) server to set the IP address of the switch. DHCP is enabled by default.
The Brocade 5300 supports both IPv4 and IPv6.
Using DHCP to set the IP address
When using DHCP, the Brocade 5300 obtains its IP address, subnet mask, and default gateway
address from the DHCP server. The DHCP client can only connect to a DHCP server that is on the
same subnet as the switch. If your DHCP server is not on the same subnet as the Brocade 5300,
use a static IP address.
Setting a static IP address
1. Log into the switch using the default password, which is password.
2. Use the ipaddrset command to set the Ethernet IP address.
If you are going to use an IPv4 IP address, enter the IP address in dotted decimal notation as
prompted.
Ethernet IP Address: [192.168.74.102]
If you are going to use an IPv6 address, enter the network information in semicolon-separated
notation as prompted.
switch:admin> ipaddrset -ipv6 --add 1080::8:800:200C:417A/64
Brocade 5300 Hardware Reference Manual
58-1000858-02
11
2
Brocade 5300 configuration
IP address is being changed...Done.
3. Complete the rest of the network information as prompted.
Ethernet Subnetmask: [255.255.255.0]
Ethernet IP Address: [192.168.74.102]
Ethernet Subnetmask: [255.255.255.0]
4. Enter off to Disable DHCP when prompted.
DHCP [OFF]: off
Date and time settings
The Brocade 5300 maintains the current date and time inside a battery-backed real-time clock
(RTC) circuit. Date and time are used for logging events. Switch operation does not depend on the
date and time; a Brocade 5300 with an incorrect date and time value still functions properly.
However, because the date and time are used for logging, error detection, and troubleshooting, you
should set them correctly.
Time zones
You can set the time zone for the switch by name. You can also set country, city or time zone
parameters.
If the time zone is not set with the new options, the switch retains the offset time zone settings. The
tsTimeZone command includes an option to revert to the prior time zone format. For more
information about the --old option, see the Fabric OS Command Reference.
You can set the time zone for a switch using the tsTimeZone command. The tsTimeZone command
allows you to perform the following tasks:
• Display all of the time zones supported in the firmware
• Set the time zone based on a country and city combination or based on a time zone ID such as
PST
The time zone setting has the following characteristics:
• You can view the time zone settings. However, only those with administrative permissions can
set the time zones.
• The tsTimeZone setting automatically adjusts for Daylight Savings Time.
• Changing the time zone on a switch updates the local time zone setup and is reflected in local
time calculations.
• By default, all switches are in the GMT time zone (0,0). If all switches in a fabric are in one time
zone, it is possible for you to keep the time zone setup at the default setting.
• System services that have already started will reflect the time zone changes only after the next
reboot.
• Time zone settings persist across failover for high availability.
12
Brocade 5300 Hardware Reference Manual
58-1000858-02
Brocade 5300 configuration
2
Local time synchronization
You can synchronize the local time of the principal or primary fabric configuration server (FCS)
switch to a maximum of eight external network time protocol (NTP) servers. To keep the time in your
SAN current, it is recommended that the principal or primary FCS switch has its time synchronized
with at least one external NTP server. The other switches in the fabric will automatically take their
time from the principal or primary FCS switch.
All switches in the fabric maintain the current clock server value in non-volatile memory. By default,
this value is the local clock server <LOCL> of the principal or primary FCS switch. Changes to the
clock server value on the principal or primary FCS switch are propagated to all switches in the
fabric.
When a new switch enters the fabric, the time server daemon of the principal or primary FCS switch
sends out the addresses of all existing clock servers and the time to the new switch. If a switch with
v5.3.0 or later has entered the fabric it will be able to store the list and the active servers; pre-5.3.0
Fabric OS switches will ignore the new list parameter in the payload and will update only the active
server address.
If the active NTP server configured is IPv6, then distributing the same in the fabric will not be
possible to switches earlier than v5.3.0 because IPv6 is supported for Fabric OS version 5.3.0 and
later. The default value LOCL will be distributed to pre-5.3.0 switches.
The tsClockServer command accepts multiple server addresses in either IPv4, IPv6, or DNS name
formats. When multiple NTP server addresses are passed, tsclockserver sets the first obtainable
address as the active NTP server. The rest are stored as backup servers that can take over if the
active NTP server fails. The principal or primary FCS switch synchronizes its time with the NTP
server every 64 seconds.
Setting the date
1. Log into the switch using the default password, which is password.
2. Enter the date command, using the following syntax:
date "mmddHHMMyy"
The values are:
•
•
•
•
•
mm is the month; valid values are 01 through 12.
dd is the date; valid values are 01 through 31.
HH is the hour; valid values are 00 through 23.
MM is minutes; valid values are 00 through 59.
yy is the year; valid values are 00 through 99 (values greater than 69 are interpreted as
1970 through 1999, and values less than 70 are interpreted as 2000-2069).
switch:admin> date
Fri Sep 29 17:01:48 UTC 2007
switch:admin> date "0927123007"
Thu Sep 27 12:30:00 UTC 2007
switch:admin>
Brocade 5300 Hardware Reference Manual
58-1000858-02
13
2
Brocade 5300 configuration
Setting time zones
You must perform the procedure on all switches for which the time zone must be set. However, you
only need to set the time zone once on each switch, because the value is written to nonvolatile
memory.
Use one of the two following procedures to set the time zone.
The following procedure describes how to set the current time zone using timezone_fmt mode to
Central Standard time.
1. Log into the switch using the default password, which is password.
2. Enter the tsTimeZone command as follows:
switch:admin> tstimezone [--interactive]/ [, timezone_fmt]
Use timezone_fmt to set the time zone by Country/City or by time zone ID, such as PST.
The following example shows how to change the time zone to US/Central.
switch:admin> tstimezone
Time Zone : US/Pacific
switch:admin> tstimezone US/Central
switch:admin> tstimezone
Time Zone : US/Central
The following procedure describes how to set the current time zone using interactive mode to
Pacific Standard Time.
1. Type the tsTimeZone command as follows:
switch:admin> tstimezone --interactive
2. You are prompted to select a general location.
Please identify a location so that time zone rules can be set correctly.
3. Enter the appropriate number or Ctrl-D to quit.
4. At the prompt, select a country location.
5. At the prompt, enter the appropriate number to specify the time zone region or Ctrl-D to quit.
Synchronizing local time using NTP
Perform the following steps to synchronize the local time using NTP.
1. Log into the switch using the default password, which is password.
2. Enter the tsClockServer command:
switch:admin> tsclockserver "<ntp1;ntp2>"
where ntp1 is the IP address or DNS name of the first NTP server, which the switch must be
able to access. The second ntp2 is the second NTP server and is optional. The operand
“<ntp1;ntp2>” is optional; by default, this value is LOCL, which uses the local clock of the
principal or primary switch as the clock server.
switch:admin> tsclockserver
LOCL
switch:admin> tsclockserver "132.163.135.131"
14
Brocade 5300 Hardware Reference Manual
58-1000858-02
Brocade 5300 configuration
2
switch:admin> tsclockserver
132.163.135.131
switch:admin>
The following example shows how to set up more than one NTP server using a DNS name:
switch:admin> tsclockserver "10.32.170.1;10.32.170.2;ntp.localdomain.net"
Updating Clock Server configuration...done.
Updated with the NTP servers
Changes to the clock server value on the principal or primary FCS switch are
propagated to all switches in the fabric.
Brocade 5300 Hardware Reference Manual
58-1000858-02
15
2
16
Brocade 5300 configuration
Brocade 5300 Hardware Reference Manual
58-1000858-02
Chapter
3
Brocade 5300 Operation
In this chapter
• Powering the Brocade 5300 on and off. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• LED activity interpretation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• POST and boot specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Interpreting POST results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Brocade 5300 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Brocade 5300 Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
22
23
23
26
Powering the Brocade 5300 on and off
Complete the following steps to power the Brocade 5300 on.
1. Connect one or both power cords to the power connectors on the power supplies and to a
power source
2. Set the AC power switches to “I”.
Power is supplied to the switch as soon as the first power supply is connected and powered on.
The switch runs POST by default each time it is powered on; it can take up to several minutes to
boot and complete POST.
To power the Brocade 5300 off, power off both power supplies by setting each AC power switch to
“O”. All devices are returned to their initial state the next time the switch is powered on.
LED activity interpretation
System activity and status can be determined through the activity of the LEDs on the switch.
There are three possible LED states: no light, a steady light, and a flashing light. The lights are
green or amber.
Sometimes, the LEDs flash either of the colors during boot, POST, or other diagnostic tests. This is
normal; it does not indicate a problem unless the LEDs do not indicate a healthy state after all boot
processes and diagnostic tests are complete.
Brocade 5300 LEDs
The Brocade 5300 has the following LEDs:
• One system status LED (above) on the left side.
• One power status LED (below) on the left side.
Brocade 5300 Hardware Reference Manual
58-1000858-02
17
3
LED activity interpretation
• Two Ethernet Port LEDs
• One port status LED for each port on the switch. These LEDs are arrayed below each pair of
Fibre Channel ports. The port LEDs are located in the array in the same relative positions as
the ports.
• One power supply LED above the AC power switch on each power supply on the non-port side
of the switch
• One fan status LED at the bottom of each fan assembly on the non-port side of the switch
LED locations
Figure 3 shows the port side of the Brocade 5300.
8
1
5
2
3
18
4
6
9
10
7
11
12
13
Brocade 5300 Hardware Reference Manual
58-1000858-02
3
LED activity interpretation
1
Brocade 5300
8
FC port status LED (port 0)
2
System status LED
9
FC port status LED (port 4)
3
System power LED
10 FC ports (0 through 7)
4
Console port
11 FC port status LED (port 48)
5
Ethernet port
12 FC port status LED (port 52)
6
Ethernet speed LED
13 FC ports (53 through 55)
7
Ethernet link LED
FIGURE 3
LEDs on Port Side of Brocade 5300
Figure 4 shows the non-port side of the switch.
1
3
2
4
8
5
9
7
10
1
Power supply #2 status LED
6
Power supply #1 status LED
2
Power supply #2
7
Power supply #1
3
Fan assembly #3
8
Fan assembly #3 status LED
4
Fan assembly #2
9
Fan assembly #2 status LED
5
Fan assembly #1
10 Fan assembly #1 status LED
FIGURE 4
6
LEDs on non-port side of Brocade 5300
Brocade 5300 Hardware Reference Manual
58-1000858-02
19
3
LED activity interpretation
LED patterns
Table 1 describes the LEDs and their actions on the port side of the switch.
TABLE 1
Port side LED patterns during normal operation
LED name
LED color
Status of hardware
Recomended action
Power Status
No light
System is off or there is an internal
power supply failure.
Verify the system is powered on
(power supply switches to “1”), the
power cables attached, and your
power source is live.
If the system power LED is not green,
the unit may be faulty.
Contact your switch service provider.
Steady green
System is on and power supplies are
functioning properly.
No action required.
No light
System is off or there is no power.
Verify the system is on and has
completed booting.
Steady green
System is on and functioning
properly.
No action required.
Steady amber (for
more than five
seconds)
Unknown state, boot failed, or the
system is faulty.
This LED displays steady amber
during POST, this is normal and does
not indicate a fault.
Perform the following steps:
Connect a serial cable to the system.
Reboot the system.
Check the failure indicated on the
system console.
Contact your switch service provider.
Flashing
amber/green
Attention is required. A number of
variables can cause this status
including a single power supply
failure, a fan failure, or one or more
environmental ranges has
exceeded.
Check the management interface
and the error log for details on the
cause of status.
Contact your switch service provider.
Ethernet
Speed
No light
Port speed is 10 Mbps.
No action required.
Steady green
Port speed is 100 Mbps.
No action required.
Ethernet Link
No light
There is no link.
Verify the Ethernet cable is
connected correctly.
Steady amber
There is a link.
No action required.
Flickering amber
There is link activity (traffic).
No action required.
System Status
20
Brocade 5300 Hardware Reference Manual
58-1000858-02
LED activity interpretation
TABLE 1
3
Port side LED patterns during normal operation (Continued)
LED name
LED color
Status of hardware
Recomended action
Port Status
No light
No signal or light carrier (media or
cable) detected.
Check transceiver and cable.
Slow flashing
green (flashing in
2-second
intervals)
Port is online but segmented
because of a loopback cable or
incompatible switch connection.
No action required.
Fast flashing green
(flashing in
half-second
intervals)
Port is online and an internal
loopback diagnostic test is running.
No action required.
Flickering green
(steady with
random flashes)
Port is online and frames are flowing
through the port.
No action required.
Steady green
Port is online, but has no traffic.
No action required.
Slow flashing
amber (flashing in
2-second
intervals)
Port is disabled (because of
diagnostics or the portDisable
command).
Verify the diagnostic tests are not
running. Re-enable the port using
the portEnable command.
Fast flashing
amber (flashing in
half-second
intervals)
Port is faulty.
Check the management interface
and the error log for details on the
cause of status.
Contact your switch service provider.
Steady amber (for
more than 5
seconds)
Port is receiving light or signal
carrier at 4 Gbps; but is not yet
online.
No action required.
Table 2 describes the LEDs on the non-port side of the switch.
TABLE 2
Non-port side LED patterns during normal operation
LED name
LED color
Status of hardware
Recomended action
Power Supply
Status
No light
Power supply is not receiving
power or is off.
Verify the power supply is on and
seated and the power cord is
connected to a functioning power
source.
Steady green
Power supply is operating
normally.
No action required.
Steady amber (for
more than 5
seconds)
Power supply fault for one of the
following reasons:
Power supply is switched off
The power cable is disconnected
The power supply has failed
Note: When the switch is first
powered on the power supply
status LED will show amber until
POST has completed.
Try the following:
Check the power cable connection.
Verify that the power supply is powered
on.
Replace the power supply FRU.
Brocade 5300 Hardware Reference Manual
58-1000858-02
21
3
POST and boot specifications
TABLE 2
Non-port side LED patterns during normal operation (Continued)
LED name
LED color
Status of hardware
Recomended action
Fan Status
No light
Fan assembly is not receiving
power.
Try the following:
Verify the fan FRU is seated correctly.
Verify the switch is powered on.
Steady green
Fan assembly is operating
normally.
No action required.
Steady amber (for
more than 5
seconds)
Fan fault for one of the following
reasons:
One or more of the fan(s) in the
fan assembly has failed
The fan FRU was disabled by the
user
Note: When the switch is first
powered on the fan status LED
will show amber until POST has
completed.
Try the following:
Verify the fan FRU is enabled (use the
fanEnable command).
Replace the fan FRU.
POST and boot specifications
When the switch is turned on or rebooted, the switch performs POST. Total boot time with POST can
be several minutes. POST can be omitted after subsequent reboots by using the fastboot command
or entering the diagDisablePost command to persistently disable POST.
For more information about these commands, refer to the Fabric OS Command Reference Manual.
POST
The success or failure results of the diagnostic tests that run during POST can be monitored
through LED activity, the error log, or the command line interface.
POST includes the following tasks:
1. Conducts preliminary POST diagnostics.
2. Initializes the operating system.
3. Initializes hardware.
4. Runs diagnostic tests on several functions, including circuitry, port functionality, memory,
statistics counters, and serialization.
Boot
In addition to POST, boot includes the following tasks after POST is complete:
1. Performs universal port configuration.
2. Initializes links.
3. Analyzes fabric. If any ports are connected to other switches, the switch participates in a fabric
configuration.
4. Obtains a domain ID and assigning port addresses.
22
Brocade 5300 Hardware Reference Manual
58-1000858-02
Interpreting POST results
3
5. Constructs unicast routing tables.
6. Enables normal port operation.
Interpreting POST results
POST is a system check that is performed each time the switch is powered on, rebooted, or reset.
During POST, the LEDs flash either amber or green. Any errors that occur during POST are listed in
the error log.
Complete the following steps to determine whether POST completed successfully and whether any
errors were detected.
1. Verify that the switch LEDs indicate that all components are healthy.
See Table 1 and Table 2 for descriptions and interpretations of LED patterns. If one or more
LEDs do not display a healthy state, verify that the LEDs on the switch are not set to “beacon”
by entering the switchShow command to detect if beaconing is active.
2. Verify that the switch prompt displays on the terminal of a computer workstation connected to
the switch.
If there is no switch prompt when POST completes, press Enter. If the switch prompt still does
not display, try opening a Telnet session or accessing the switch through another management
tool. If this is not successful, the switch did not successfully complete POST. Contact your
switch supplier for repair.
3. Review the switch system log for errors. Any errors detected during POST are written to the
system log, accessible through the errShow command.
For information about all referenced commands, and on accessing the error log, refer to Fabric OS
Administrator’s Guide. For information about error messages, refer to the Fabric OS Message
Reference Manual.
Brocade 5300 Maintenance
The Brocade 5300 is designed for high availability and low failure; it does not require any regular
physical maintenance. It includes diagnostic tests and field-replaceable units, described in the
following sections.
Installing an SFP
The Brocade 5300 only supports Brocade-branded SFPs. If you use an unqualified SFP, the
switchShow command output shows the port in a Mod_Inv state. Fabric OS also logs the issue in
the system error log.
Complete the following steps to install an SFP.
1. Making sure that the bail (wire handle) is in the unlocked position, place the SFP in the
correctly oriented position on the port, as shown in Figure 5.
2. Slide the SFP into the port until you feel it click into place; then close the bail.
Brocade 5300 Hardware Reference Manual
58-1000858-02
23
3
Brocade 5300 Maintenance
NOTE
Each SFP has a 10-pad gold-plated PCB-edge connector on the bottom. The correct position to
insert an SFP into the upper row of ports is with the gold edge down. The correct position to insert
an SFP into the lower row of ports is with the gold edge up.
FIGURE 5
Installing an SFP in the upper row of port slot
Diagnostic tests
In addition to POST, Fabric OS includes diagnostic tests to help you troubleshoot the hardware and
firmware. This includes tests of internal connections and circuitry, fixed media, and the
transceivers and cables in use.
The tests are implemented by command, either through a Telnet session or through a console set
up to the serial connection to the switch. Some tests require the ports to be connected by external
cables, to allow diagnostics to verify the serializer/deserializer interface, transceiver, and cable.
Some tests require loopback plugs.
Diagnostic tests run at link speeds of 1, 2, 4 and 8 Gbps depending on the speed of the link being
tested.
NOTE
Diagnostic tests might temporarily lock the transmit and receive speed of the links during
diagnostic testing.
For information about specific diagnostic tests, see the Fabric OS Troubleshooting and Diagnostics
Guide.
24
Brocade 5300 Hardware Reference Manual
58-1000858-02
3
Brocade 5300 Maintenance
Field Replaceable Units (FRUs)
You can replace the power supplies and fan assemblies on site without the use of special tools. The
power supplies and fan assemblies are keyed to ensure correct orientation during installation.
Installation instructions are provided with all replacement units.
Power supplies
The two power supplies are hot-swappable. They are identical and fit into either power supply slot.
Fabric OS identifies the power supplies as follows (viewing the switch from the non-port side):
• Power supply 1 on the right
• Power supply 2 on the left
Use one of the following methods to determine if you need to replace a power supply.
• Check the power supply status LED next to the On/Off switch (see “LED locations” on
page 18)
• In Web Tools, click the Power Status icon.
• Enter the psShow command at the prompt to display power supply status as shown below:
br5300:admin> psshow
Power Supply #1 is OK
V10529,
TQ2H0000030
,2X,TQ2H0000
Power Supply #2 is OK
V10541,
TQ2H0000189
,TQ2H0000
br5300:admin>
,60-0300031-01,X2,
,SP640
,60-0300031-01,X3,
,SP640-2P
,A
For further information on replacing the power supplies, see the Mid-Size Switch Power Supply
Replacement Procedure.
Fan assemblies
The three fan assemblies are hot-swappable. They are identical and fit into any fan assembly slot.
Each fan assembly contains two fans, identified by Fabric OS as follows (viewing the switch from
the non-port side):
• Fan assembly #1 on the right
• Fan assembly #2 in the center
• Fan assembly #3 on the left
Use one of the following methods to determine if you need to replace a fan assembly.
• Check the fan status LED on the face of the fan assembly (see “LED locations” on
page 18)
• In Web Tools, click the Fan Status icon.
Brocade 5300 Hardware Reference Manual
58-1000858-02
25
3
Brocade 5300 Management
• Enter the fanShow command at the prompt:
br5300:admin> fanshow
Fan 1 is Ok, speed is 4821 RPM
Fan 2 is Ok, speed is 4821 RPM
Fan 3 is Ok, speed is 4891 RPM
br5300:admin>
For further information on replacing the fan assemblies, see the Brocade 5300 Fan Assembly
Replacement Procedure.
Brocade 5300 Management
You can use the management functions built into the Brocade 5300 to monitor the fabric topology,
port status, physical status, and other information to help you analyze switch performance and to
accelerate system debugging.
The Brocade 5300 automatically performs power-on self-test (POST) each time it is turned on. Any
errors are recorded in the system error log. For more information about POST, see “POST and boot
specifications” on page 22.
For information about upgrading the version of Fabric OS installed on your switch, see the Fabric
OS Administrator’s Guide.
You can manage the Brocade 5300 using any of the management options listed in Table 3.
TABLE 3
Management Options for the Brocade 5300 Switch
Management Tool
Out-of-band Support
In-band Support
Command line interface (CLI)
Up to two admin sessions and four user sessions simultaneously.
For more information, refer to the Fabric OS Administrator’s Guide
and the Fabric OS Command Reference Manual.
Ethernet or serial
connection
IP over Fibre Channel
Brocade Web Tools
For information, refer to the Web Tools Administrator’s Guide.
Ethernet or serial
connection
IP over Fibre Channel
Standard SNMP applications
For information, refer to the MIB Reference Manual.
Ethernet or serial
connection
IP over Fibre Channel
Brocade Fabric Manager (option to purchase)
Ethernet or serial
For information, refer to the Fabric Manager Administrator’s Guide. connection
IP over Fibre Channel
Management Server
For information, refer to the Fabric OS Administrator’s Guide and
the Fabric OS Command Reference Manual.
Ethernet or serial
connection
Native in-band
interface
(over HBA only)
EFCM (option to purchase)
For information, refer to theEFCM documentation set.
Ethernet or serial
connection
IP over Fibre Channel
NOTE
To achieve in-band support for IP over Fibre Channel, the software must be run on both the HBA and
the switch, and it must be supported by both the HBA and HBA driver.
26
Brocade 5300 Hardware Reference Manual
58-1000858-02
Appendix
A
Brocade 5300 Specifications
In this appendix
• Switch components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Weight and physical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Facility requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Power supply specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Environmental requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• General specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Data transmission ranges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Memory specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Fibre Channel port specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Serial port specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Regulatory compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
28
28
28
29
29
31
31
31
32
32
Switch components
The Brocade 5300 switch includes the following components:
• Cabinet-mountable 2U chassis designed to be mounted in a 19-in. cabinet space, with
forced-air cooling that flows from the non-port side of the switch to the port side
• 80 Fibre Channel ports, compatible with short wavelength (SWL), long wavelength (LWL), and
extended long wavelength (ELWL) SFP transceivers
• Two IEEE-compliant RJ-45 connector on the port side of the switch for use with a serial console
and 10/100 MB Ethernet
• 80 port Link LEDs, one switch power LED, one switch status LED, two Ethernet LEDs, two
power supply LEDs, and three fan LEDs
• 2 universal AC power supplies with AC switches and built-in fans
• 3 fan assemblies containing two fans each. The fans have two speeds, which are set
automatically and cannot be modified. They default to high speed upon boot, then switch to
low speed as Fabric OS comes online, returning to high speed only as required.
Brocade 5300 Hardware Reference Manual
58-1000858-02
27
A
Weight and physical dimensions
Weight and physical dimensions
Table 4 lists the weight and dimensions of the Brocade 5300.
TABLE 4
Physical specifications
Dimension
Value
Height
2U or 8.6 cm (3.4 in.)
Depth
61 cm (24 in.)
Width
42.8 cm (16.8 in.)
Weight (with two power supplies, three fan assemblies,
and zero SFPs installed)
15.6 kg (34.4 lb)
Facility requirements
Table 5 provides the facilities requirements that must be met for the Brocade 5300.
TABLE 5
Facility Requirements
Type
Requirements
Electrical
•
•
Primary AC input 100-240 VAC, 2.0A, 47-63 Hz; switch autosenses input voltage
Adequate supply circuit, line fusing, and wire size, as specified by the electrical rating
on the switch nameplate
• Circuit protected by a circuit breaker and grounded in accordance with local electrical
codes
Refer to Table 6 on page 28 for complete power supply specifications.
Thermal
•
Cabinet (when
rack-mounted)
•
•
•
•
•
A minimum air flow of 79.8 cubic meters/hour (47 cubic ft/min.) available in the
immediate vicinity of the switch
Ambient air temperature not exceeding 40° C (104° F) while the switch is operating
Two rack units (2U) in a 48.3 cm (19-inches) cabinet
All equipment in cabinet grounded through a reliable branch circuit connection
Additional weight of switch not to exceed the cabinet’s weight limits
Cabinet secured to ensure stability in case of unexpected movement
Power supply specifications
The power supplies are universal and capable of functioning worldwide without voltage jumpers or
switches. They meet IEC 61000-4-5 surge voltage requirements and are autoranging in terms of
accommodating input voltages and line frequencies. Each power supply has a built-in fan for
cooling, pushing air towards the port side of the switch.
Table 6 lists the power supply specifications for the Brocade 5300.
TABLE 6
28
Power Supply Specifications
Specification
Value
Inlet
C13
Maximum output of one power supply
300 Watts
Brocade 5300 Hardware Reference Manual
58-1000858-02
Environmental requirements
TABLE 6
A
Power Supply Specifications
Specification
Value
Nominal system DC power consumption
260 Watts
Input voltage
85-264 VAC
Input line frequency
47-63HZ
BTU rating
1313 BTU/hr
Inrush current
Maximum of 38A for period of 10-150mS
Input line protection
Both AC lines are fused
Environmental requirements
Table 7 lists the acceptable environmental ranges for both operating and nonoperating (such as
during transportation or storage) conditions.
TABLE 7
Environmental requirements
Condition
Acceptable during operation
Acceptable During Non-Operation
Ambient
Temperature
0º to 40º C
32º to 104º F
-25º to 70º C
-13º to 158º F
Humidity
10% to 85% RH non-condensing, at
40º C (104º F), with maximum gradient of 10%
per hour
10% to 90% RH non-condensing, at 70º C
(158º F)
Altitude
0 to 3 km (10,000 feet) above sea level
0 to 12 km (40,000 feet) above sea level
Shock
20 G, 6 ms, half-sine wave
33 G, 11 ms, 3/eg Axis
Vibration
0.5 G, 5-500 Hz
2.0 G, 5-500 Hz
Air flow
High speed 9000 RPM 102 CMH (60 CFM)
Low speed 6000 RPM 74.8 CMH (44 CFM)
None required.
General specifications
Table 8 lists the general specifications for the Brocade 5300.
TABLE 8
General specifications
Specification
Description
Configurable port types
F_Port, FL_Port, E_Port, EX_Port, and M_Port
System architecture
Nonblocking shared-memory switch
System processor
Freescale MPC8548 x 1.3GHz
ANSI Fibre Channel protocol
FC-PH (Fibre Channel Physical and Signalling Interface standard)
Modes of operation
Fibre Channel Class 2 and Class 3
Fabric initialization
Complies with FC-SW-3 Rev. 6.6
FC-IP (IP-over-Fibre Channel)
Complies with FC-IP 2.3 of FCA profile
Brocade 5300 Hardware Reference Manual
58-1000858-02
29
A
General specifications
TABLE 8
General specifications
Specification
Description
Aggregate switch I/O bandwidth
1280 Gbps if all 80 ports are running at 8 Gbps, full duplex
Port-to-port latency
Less than 2100 nanoseconds with no contention (destination port is free)
Table 9 lists the electromagnetic compatibility (EMC) for the Brocade 5300.
TABLE 9
EMC specifications
Country
Safety
EMC
United States
Bi_Nat UL/CSA 60950-1 1st Ed or
latest
ANSI C63.4
Canada
Bi_Nat UL/CSA 60950-1 1st Ed or
latest
ICES-003 Class A
Japan
European Community
CISPR22 and JEIDA (Harmonics)
EN60950-1 or latest
Australia/New Zealand
EN55022 or CISPR22 or AS/NZS
CISPR22
Argentina
IEC60950-1 or latest
Russian Federation
IEC60950-1 or latest
Korea
30
EN55022 and EN55024
51318.22-99 and 51318.24.99
KN22 and KN24
China (PS only)
GB4943-2001 and
GB9254-1998 or latest
GB17625.1-2003 or latest
Taiwan (PS only)
CNS 14336(94) or latest
CNS 13438(95) or latest
Brocade 5300 Hardware Reference Manual
58-1000858-02
Data transmission ranges
A
Data transmission ranges
Table 10 provides the data transmission ranges for different cable types and port speeds.
TABLE 10
Data transmission ranges
Port Speed
Cable Size
(microns)
Short Wavelength (SWL)
Long Wavelength (LWL)
Extended Long
Wavelength (ELWL)
1 Gbps
50
500 m (1,640 ft) (OM2)
860 m (2,821 ft) (OM3)
NA
NA
62.5
300 m (984 ft)
NA
NA
9
NA
10 km (6.2 mi)
80 km (50 mi)
50
300 m (984 ft) (OM2)
500 m (1,640 ft) (OM3)
NA
NA
62.5
150 m (492 ft)
NA
NA
9
NA
10 km (6.2 mi)
80 km (50 mi)
50
150 m (492 ft) (OM2)
380 m (1,246 ft) (OM3)
NA
NA
62.5
70 m (230 ft)
NA
NA
9
NA
10 km (6.2 mi)
NA
50
50 m (164 ft) (OM2)
150 m (492 ft) (OM3)
NA
NA
62.5
21 m
NA
NA
9
NA
10 km
NA
2 Gbps
4 Gbps
8 Gbps
Up to 500 km at 1G is supported when using long distance transport system such as DWDM.
Memory specifications
The Brocade 5300 has three types of memory devices:
TABLE 11
Brocade 5300 memory specifications
Type
Size
Boot flash
4 MB
Compcat flash
1 GB
Main memory (DDR2 SDRAM)
1 GB
Fibre Channel port specifications
The Fibre Channel ports in the Brocade 5300 are compatible with SWL, LWL, and ELWL SFP
transceivers. The strength of the signal is determined by the type of transceiver in use.
The ports meet all required safety standards. For more information about these standards, see
“Regulatory compliance” on page 32.
Brocade 5300 Hardware Reference Manual
58-1000858-02
31
A
Serial port specifications
The ports are capable of operating at 1, 2, 4, or 8 Gbps and are able to autonegotiate to the
maximum link speed.
Serial port specifications
The serial port is located on the port side of the switch. The Brocade 5300 uses an RJ-45
connector for the serial port. An RJ-45 to DB9 adaptor cable is also provided with the switch.
NOTE
To protect the serial port from damage, keep the cover on the port when not in use.
The serial port can be used to connect to a workstation to configure the switch IP address before
connecting the switch to a fabric or IP network. The serial port’s parameters are fixed at 9600
baud, 8 data bits, and no parity, with flow control set to None.
Table 12 lists the serial cable pinouts.
TABLE 12
Serial cable pinouts
PIN
Signal
Description
1
Not supported
NA
2
Not supported
NA
3
UART1_TXD
Transmit data
4
GND
Logic ground
5
GND
Logic ground
6
UART1_RXD
Receive data
7
Not supported
NA
8
Not supported
NA
Regulatory compliance
This section describes the regulatory compliance requirements for the Brocade 5300. It contains:
•
•
•
•
•
•
•
•
•
•
•
32
“FCC warning (US only),” next
“MIC statement (Republic of Korea)” on page 33
“VCCI statement Japan” on page 33
“Power cords (Japan Denan)” on page 33
“BSMI statement (Taiwan)” on page 33
“CE statement” on page 34
“Canadian requirements” on page 34
“Laser compliance” on page 34
“RTC battery” on page 34
“Electrical safety” on page 35
“Regulatory certifications” on page 35
Brocade 5300 Hardware Reference Manual
58-1000858-02
Regulatory compliance
A
FCC warning (US only)
This equipment has been tested and complies with the limits for a Class A computing device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and
used in accordance with the instruction manual, might cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at the user’s own
expense.
MIC statement (Republic of Korea)
VCCI statement Japan
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,
radio disturbance might arise. When such trouble occurs, the user might be required to take
corrective actions.
Power cords (Japan Denan)
BSMI statement (Taiwan)
The BSMI Statement is applicable to Brocade 5300 power supplies.
Brocade 5300 Hardware Reference Manual
58-1000858-02
33
A
Regulatory compliance
CE statement
ATTENTION
This is a Class A product. In a domestic environment, this product might cause radio interference,
and the user might be required to take corrective measures
The standards compliance label on the Brocade 5300 contains the CE mark which indicates that
this system conforms to the provisions of the following European Council directives, laws, and
standards:
• Electromagnetic Compatibility (EMC) Directive 2004/108/EEC
• Low Voltage Directive (LVD) 2006/95/EC
• EN50082-2/EN55024:1998 (European Immunity Requirements)
- EN61000-3-2/JEIDA (European and Japanese Harmonics Spec)
- EN61000-3-3
Canadian requirements
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations, ICES-003 Class A.
Laser compliance
This equipment contains Class 1 laser products and complies with FDA Radiation Performance
Standards, 21 CFR Subchapter I and the international laser safety standard IEC 825-2.
ATTENTION
Use only optical transceivers that are qualified by Brocade Communications Systems, Inc. and
comply with the FDA Class 1 radiation performance requirements defined in 21 CFR Subchapter I,
and with IEC 825-2. Optical products that do not comply with these standards might emit light that
is hazardous to the eyes.
RTC battery
ATTENTION
Do not attempt to replace the real-time clock (RTC) battery. There is danger of explosion if the battery
is incorrectly replaced or disposed of. Contact your switch supplier if the real-time clock begins to
lose time.
34
Brocade 5300 Hardware Reference Manual
58-1000858-02
Environmental regulation compliance
A
Electrical safety
ATTENTION
This switch might have more than one power cord. To reduce the risk of electric shock, disconnect
both power cords before servicing.
ATTENTION
Connect the power cord only to a grounded outlet.
ATTENTION
This product is designed for an IT power system with phase-to-phase voltage of 230V. After operation
of the protective device, the equipment is still under voltage if it is connected to an IT power system.
Regulatory certifications
Table 13 lists the EMC compatibility for the Brocade 5300.
TABLE 13
EMC (electromagnetic compatibility)
Country
Safety
EMC
United States
Bi_Nat UL/CSA 60950-1 1st Ed or
latest
ANSI C63.4
Canada
Bi_Nat UL/CSA 60950-1 1st Ed or
latest
ICES-003 Class A
Japan
European Community
CISPR22 and JEIDA (Harmonics)
EN60950-1 or latest
Australia/New Zealand
EN55022 and EN55024
EN55022 or CISPR22 or AS/NZS
CISPR22
Argentina
IEC60950-1 or latest
Russian Federation
IEC60950-1 or latest
Korea
51318.22-99 and 51318.24.99
KN22 and KN24
China (PS only)
GB4943-2001 and
GB9254-1998 or latest
GB17625.1-2003 or latest
Taiwan (PS only)
CNS 14336(94) or latest
CNS 13438(95) or latest
Environmental regulation compliance
This section describes the “China RoHS” environmental regulatory compliance requirements for
the Brocade 5300 switch.
Brocade 5300 Hardware Reference Manual
58-1000858-02
35
A
Environmental regulation compliance
China RoHS
The contents included in this section are per the requirements of the People's Republic of ChinaManagement Methods for Controlling Pollution by Electronic Information products.
䙉ᅜ⦃๗⊩㾘
Ё೑ RoHS
ᴀ㡖Ёࣙ৿ⱘ‫ݙ‬ᆍ䛑䙉ᅜњЁढҎ⇥݅੠೑lj⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩NJⱘ
㽕∖DŽ
Environmental protection use period (EPUP) disclaimer
In no event do the EPUP logos shown on the product and FRUs alter or expand that warranty that
Brocade provides with respect to its products as set forth in the applicable contract between
Brocade and its customer. Brocade hereby disclaims all other warranties and representations with
respect to the information contained on this CD including the implied warranties of merchantability,
fitness for a particular purposes and non-infringement.
The EPUP assumes that the product will be used under normal conditions in accordance with the
operating manual of the product.
⦃ֱՓ⫼ᳳ䰤 (EPUP) ‫ܡ‬䋷ໄᯢ˖
EPUP
ᷛᖫϡӮߎ⦄೼ѻક੠
FRU
ⱘᬍ㺙ѻકЁˈгϡӮᇍ
Brocade
᠔ᦤկⱘⳌ݇ѻકֱׂᴵℒ˄䆹ֱׂᴵℒ೼
Brocade
ঞ݊ᅶ᠋䯈䖒៤ⱘ䗖⫼ড়ৠЁ߫ߎ˅䖯㸠๲㸹DŽᇍѢℸ
CD
Ϟࣙ৿ⱘⳌֵ݇ᙃˈབ䗖䫔ᗻǃ䩜ᇍ⡍ᅮ⫼䗨ⱘ䗖⫼ᗻ੠䴲։ᴗᗻⱘᱫ⼎ֱ䆕ˈBr
ocade ೼ℸ䚥䞡ໄᯢᴀ݀ৌᇍѢϢϞ䗄ֵᙃⳌ݇ⱘ᠔᳝݊Ҫֱ䆕੠䰜䗄ὖϡ䋳䋷DŽ
EPUP ‫؛‬䆒೼Āѻક᪡԰᠟‫ݠ‬āЁ⊼ᯢⱘᐌ㾘ᴵӊϟՓ⫼䆹ѻકDŽ
TS/HS dual language sheet
In accordance with China's Management Measures on the Control of Pollution caused by Electronic
Information products (Decree No. 39 by the Ministry of Information Industry), the following
information is provided regarding the names and concentration level of Hazardous substances (HS)
which may be contained in this product.
TABLE 14
36
China ROHS hazardous substances/toxic substances (HS/TS) concentration chart
Name of the
Component
Hazardous/Toxic Substance/Elements
Lead (PB)
Mercury
(Hg)
Cadium
(CD)
Hexavalent
Chromium
(CR6+)
Polybrominated
Biphenyl (PBB)
Polybrominated
Diphenyl Ether
(PBDE)
Fibre Channel
Switch
X
O
O
O
O
O
Fan, Blower
assemblies
X
O
O
O
O
O
PCBA cards
X
O
O
O
O
O
Power Supply kit
X
O
O
O
O
O
Brocade 5300 Hardware Reference Manual
58-1000858-02
Environmental regulation compliance
TABLE 14
A
China ROHS hazardous substances/toxic substances (HS/TS) concentration chart
Name of the
Component
Hazardous/Toxic Substance/Elements
Lead (PB)
Mercury
(Hg)
Cadium
(CD)
Hexavalent
Chromium
(CR6+)
Polybrominated
Biphenyl (PBB)
Polybrominated
Diphenyl Ether
(PBDE)
SFPs (optical
cable
connectors)
X
O
O
O
O
O
Sheet Metal
X
O
O
O
O
O
Chassis
Assembly
X
O
O
O
O
O
Mechanical
brackets and
Slides
X
O
O
O
O
O
Slot Filler
X
O
O
O
O
O
Cable
management
tray
X
O
O
O
O
O
Cable Comb
O
O
O
O
O
O
Cables and
power cords
O
O
O
O
O
O
Replacement
Doors
X
O
O
O
O
O
Software/
Documentation
CDs
O
O
O
O
O
O
X indicates that the concentration of such hazardous/toxic substance in all the units of
homogeneous material of such component is higher than the SJ/T11363-2006 Requirements for
Concentration Limits.
Brocade 5300 Hardware Reference Manual
58-1000858-02
37
A
Environmental regulation compliance
O indicates that no such substances are used or that the concentration is within the
aforementioned limits.
38
Brocade 5300 Hardware Reference Manual
58-1000858-02
Index
A
F
access
NTP, 14
Fabric Manager, 26
facility requirements, 28
FCC warning (US only), 33
Fibre Channel Association, x
Fibre Channel port specifications, 31
field replaceable units (FRUs), 25
front panel
LEDs, 17
FRUs, 25
B
boot, 22
Brocade Advanced Web Tools, 26
Brocade Fabric Manager, 26
BSMI statement (Chinese), 33
C
Canadian requirements, 34
CE statement, 34
China RoHS, 35
Command line interface (CLI), 26
configuring
date and time, 12
NTP, 14
configuring the Brocade 5300, 10
D
data transmission ranges, 31
date, 13
date and time, 12
diagnostic tests, 24
E
electrical safety, 35
environmental requirements, 29
event
date and time, 12
Brocade 5300 Hardware Reference Manual
53-100858-02
G
general specifications, 29
I
installation and safety considerations, 7
installing a Brocade 5300 into an EIA cabinet, 10
installing a stand-alone Brocade 5300, 9
installing an SFP, 23
interpreting LED activity, 17
interpreting post results, 23
items included with the Brocade 5300, 7
items required for installation, 9
L
laser compliance, 34
LEDs
interpreting, 17
on front panel, 17
LEDs on the port side of the switch, 17
local clock, 14
LOCL, 14
logging
timestamp, 12
39
M
maintaining, 23
Management Server, 26
managing, 26
memory specifications, 31
MIC statement (Republic of Korea), 33
monitoring
through LED activity, 17
N
nonport side view, 3
NTP
access, 14
O
overview, 1
P
POD license, 4
port side view, 2
ports on demand license, 4
post, 22
post and boot specifications, 22
power supply specifications, 28
provide power to the switch, 10
setting the default account passwords, 12
setting the IP address, 11
setting the switch date and time, 12
Setting time zones, 14
settings
date and time, 12
SNMP, 26
switch components, 27
T
time, 12
time and date, 12
Time zones, 12
time zones, 12
tsclockserver, 14
tsTimeZone, 14
V
VCCI statement, 33
W
weight and physical dimensions, 28
R
recommendations for cable management, 8
regulatory certifications, 35
regulatory compliance, 32
RTC battery, 34
S
serial port specifications, 32
setting
time zone, 14
setting the date and time, 12
40
Brocade 5300 Hardware Reference Manual
53-100858-02