Convertible
Booster Seat
for vehicle use.
Forward Facing
Install with lap or lap-sash
seat belt and upper
anchorage strap for children
8kg to 18kg with the inbuilt
harness straps.
Forward Facing.
Use as a booster seat with only a
lap-sash seat belt for children 14kg
to 26kg.
(Also suitable for use with
Safe-n-Sound Protecta™
Child Safety Harness
Series 120)
INFORMATION FOR BUYERS:
FOR CHILDREN FROM 8kg TO 26 KG.
CHECK THAT THIS CHILD RESTRAINT WILL FIT IN
YOUR CAR.
IMPORTANT: KEEP THIS BOOKLET IN THE PLACE
PROVIDED ON THE CHILD RESTRAINT.
MAXI RIDER™
Series number:
8000/A/2004
Instructions for
Installation & Use
INDEX
FOR TODDLER AND CHILD USE
WHO TO CONTACT
2. INTRODUCTION
GENERAL WARNINGS
3. PRE- INSTALLATION
FOR TODDLER USE
SPECIAL FEATURES
SUITABLE FOR USE
WARNINGS
HOW TO SET-UP
HOW TO INSTALL
HOW TO USE
3.
4.
FOR CHILD USE
SPECIAL FEATURES
SUITABLE FOR USE
WARNINGS
HOW TO SET-UP
HOW TO INSTALL
USING WITH CHILD HARNESS
8.
9.
9.
11.
12.
15.
16.
17.
17.
18.
21.
23.
FOR TODDLER AND CHILD USE
28. ACCESSORIES & FEATURES
HOW TO CLEAN
29. IN CASE OF ACCIDENT
CARE & MAINTENANCE
30.
32.
EASY SELECTOR GUIDE
Birth
8kg
9kg
14kg
12kg
*
18kg
26kg
32kg
*
Infant Restraint
Convertible
Child Car Seat
*
*
Forward-Facing
Child Car Seat
Convertible
Booster Seat
Child Booster Seats
and Booster Cushions
Child Harness
*Refer to Catalogue.
WHO TO CONTACT
AUSTRALIA
Britax Childcare Pty. Ltd. A Britax International company.
NEW ZEALAND
Britax Childcare NZ Limited. A Britax International company.
(Incorporated in Victoria) A.C.N. 006 773 600 A.B.N 55 006 773 600.
PO Box 100-247 Auckland 9 Phone: (09) 443 0102
Head office: 99 Derby Road Sunshine, Victoria 3020
Fax: (09) 443 0120 Phone toll free: 0800 688 822.
Phone: (03) 9288 7288 Fax: (03) 9311 5798
INTERNATIONAL ENQUIRIES
For interstate and country enquiries, Service & Spare
Contact your Local Distributor.
Parts (9:30am to 5:00pm E.S.T.) Phone: 1300 303 330
2
For Toddler & Child Use.
INTRODUCTION
THE MAXI RIDER™ IS SUITABLE FOR TODDLERS AND OLDER CHILDREN AS A
CONVERTIBLE BOOSTER SEAT. THIS CHILD RESTRAINT IS FITTED WITH OUR
EXCLUSIVE VERSA-TETHER™ CATCH THAT ALLOWS IT TO USE THE SAFE-NSOUND PROTECTA™ CHILD SAFETY HARNESS IN BOOSTER SEAT MODE FOR
OLDER CHILDREN.
No child restraint can guarantee absolute protection from injury in every crash.
However, to ensure that your child gets all the protection designed into the restraint
PLEASE READ AND FOLLOW THESE INSTRUCTIONS EXACTLY and use only Safen-Sound (Britax) recommended parts and accessories.
GENERAL WARNINGS ALSO SEE WARNINGS ON PAGES 8 AND 16.
Carefully read all the instructions for installation. In the event of doubt about the method of
installation, consult Britax childcare or agent or a child restraint fitting station authorized by a
relevant transport authority or, in New Zealand, the agent for the vehicle.
DO NOT USE THIS BOOSTER SEAT IF THE CHILD’S EYE LEVEL IS ABOVE THE TOP OF THE
BOOSTER SEAT BACK WHEN THE CHILD IS SEATED.
DO NOT USE THIS RESTRAINT IF THE CHILD'S EYE LEVEL IS ABOVE THE TOP OF THE CAR
SEAT BACK OR HEADREST WHEN THE CHILD IS SEATED ON THE CHILD RESTRAINT.
THIS RESTRAINT MUST BE ATTACHED TO A CHILD RESTRAINT ANCHORAGE POINT IN THE
CAR. REFER TO CAR OWNER’S HANDBOOK FOR LOCATION OF ANCHORAGE POINTS.
REFER TO A CHILD RESTRAINT FITTING STATION IF NO ANCHORAGE POINTS ARE IN THE
MOTOR CAR.
If your vehicle is not fitted with an anchor point, please contact a Safety Restraint Fitting Station
authorised by the relevant State Government Body for correct fitment of the restraint. In New
Zealand contact the agent for the vehicle. The upper anchorage strap must be attached to an
anchorage point using an extension strap if necessary.
Do not use seat belt extenders, even if the car seat belt is not long enough to secure the child
restraint.
Supervision of children is needed because they may be able to undo buckles and adjusters.
Use the restraint exactly as shown in the instructions.
DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR.
Do not alter or modify this restraint, repairs must only be done by the manufacturer or agent.
Do not allow the restraint to come into contact with polishes, oils, bleach and other chemicals.
Destroy the restraint if it has been in a severe crash, even if no damage is visible.
DO NOT USE THIS RESTRAINT WITHOUT THE COVER.
Regularly check the restraint components, straps and other fitments for correct function and
condition. Seek prompt repair.
DO NOT USE CHILD RESTRAINTS IN A SEATING POSITION WHERE AN AIRBAG IS FITTED.
FOLLOW THE CAR MANUFACTURER’S RECOMMENDATIONS.
Straps may be damaged by unsecured cargo in a collision. Secure or remove hazardous cargo
before using this restraint. HATCH-BACK OR WAGON: Do not use the child restraint where this
strap may fall into a split in the seat back.
Protect all webbing from abrasion and cutting by sharp corners and edges.
The restraint should not be purchased or sold as a second hand item. It is recommended not to use
child restraints older than 10 years as the protection in an accident may be reduced.
For Toddler & Child Use
3
PRE-INSTALLATION
Consult the vehicle owner's handbook for location of anchor fittings or anchorage points
and the possible use of spacers. Some vehicles may have an anchor fitting fitted by the
vehicle manufacturer. If anchorage points cannot be found refer to car manufacturer or
local child restraint fitting station or traffic authority for optimum position of anchorage
point and the use of spacers.
UPPER ANCHORAGE STRAP
IMPORTANT WARNING: THE ATTACHMENT CLIP COVER MUST ALWAYS BE USED AS
IT PREVENTS THE RISK OF INCORRECT FITMENT OF THE ATTACHMENT CLIP TO
THE ANCHOR FITTING. ALWAYS ENSURE THAT THE ATTACHMENT CLIP IS
CORRECTLY ENGAGED TO THE ANCHOR FITTING AND NOT HOOKED OR FITTED TO ANY
OTHER OBJECT BEFORE EACH USE OF THE RESTRAINT. THIS IS ESPECIALLY
IMPORTANT IN VEHICLES SUCH AS STATION WAGONS, VANS, HATCH BACKS OR
VEHICLES WITHOUT A FIXED PARCEL SHELF, SINCE THE ANCHOR POINT IS USUALLY
NOT VISIBLE.
IMPORTANT INSTALLATION NOTE:
In some vehicles the anchor fitting in the rear vertical panel can only be installed in one
way. Please refer to vehicle owner's
handbook or a child restraint fitting station for
correct method.
Extension Strap distance to be measured:
Front of
vehicle
Length 300mm (Use Safe-n-Sound part 0035 or equivalent).
Length 600mm (Use Safe-n-Sound part 0036 or equivalent).
Available from all major child restraint retailers.
CORRECT
ENGAGEMENT OF
ATTACHMENT CLIP TO
ANCHOR FITTING.
Adjustable upper
anchorage strap.
The shaded areas of this diagram illustrate the possible locations of the anchor fitting. Within each
shaded area is an anchor fitting showing the correct way to install the fitting. Ensure the anchor
fitting is aligned as illustrated unless stated otherwise in the vehicle owner’s handbook.
4
For Toddler & Child Use
PRE-INSTALLATION
ANCHOR FITTING:
WARNING: CHILD RESTRAINTS MUST NOT BE ATTACHED TO UNSOUND
METAL OR TO WOOD, OR SYNTHETIC STRUCTURES. WHEN DRILLING 9 MM
HOLE DO NOT DRILL THROUGH FUEL LINES, FUEL TANKS, ELECTRICAL
WIRING, OR RADIO SPEAKERS. WEBBING STRAPS MUST BE PROTECTED FROM
SHARP CORNERS AND EDGES. THE ANCHOR FITTING MUST BE USED ONLY AS
DESCRIBED ABOVE. IT MUST NOT BE HOOKED ONTO ANY OTHER OBJECT.
If the car is fitted with child restraint anchorage point...
Locate the anchorage point behind the rear seating position Lock washer
to be used. Consult the car owners handbook for the location
of the anchorage points. The anchorage point should be
directly behind and central to the restraint. Remove thread
plug from the parcel shelf, floor/roof, etc. and install anchor bolt
and fitting as shown right.
Trim
Anchor bolt
Anchor fitting
Spacers
(if required)
CAUTION: Do not overtighten anchor bolt. Overtightening may
fracture or break bolt. Maximum torque is 20 N.m. (14.75 ft.lb.)
Note: Minimum of five full turns of anchor bolt is required before
tightening force is applied. Do not overtighten.
Metal
panel
Front of vehicle
If the car is not fitted with child restraint
anchorage points...
200 mm
min.
For Sedans only - Drill 9mm diameter hole in
the parcel shelf on the centreline of the seating
position as shown right. Before drilling the hole,
check the underside for accessibility.
For vehicles other than Sedans - In Australia,
consult your nearest child restraint fitting
station or traffic authority for vehicle
inspection to find the best, correct position for the
placement of the anchorage point, and for the
correct attachment bolt length and use of spacers.
In New Zealand, consult the agent for the vehicle.
Centre line of
seating position
Note to Queensland purchasers: The installation of
anchorage points must be approved by authorised officers
appointed by Queensland Transport. Authorised officers
can be sourced from all Queensland Transport Customer
Service and Queensland Ambulance Service Centres.
Drill 9 mm
diameter hole.
Do not drill
through fuel
lines, fuel tanks,
electrical wiring
or radio speakers.
Anchor bolt
Anchor fitting
Spacers (if required)
ONLY USE A 5/16 UNC GRADE 5 BOLT.
IF THE BOLT IS NOT THE CORRECT
LENGTH THE CAR MANUFACTURER’S
HAND BOOK CAN PROVIDE ADVICE ON
THE CORRECT LENGTH BOLT.
Trim
Metal
panel
Front of vehicle
Reinforcing washer
Lock washer
Securing nut
For Toddler & Child Use
5
PRE-INSTALLATION
INSTALLATION AND USE OF RESTRAINT
For Toddler Use Pages 7-14.
For Child Use Pages 15-26.
TO REMOVE RESTRAINT FROM VEHICLE
A. Disengage seat belt tongue from buckle and
remove from restraint.
B. Fully press Upper Anchorage Strap Adjuster
Button (A) while pulling Upper Anchorage Strap
(B) to slacken as shown right. In some vehicles
loosening of the Upper Anchorage Strap may be
difficult. If so, try pushing the restraint against the
vehicle seat back or slightly lifting the restraint to
release the tension.
C. Disengage Attachment Clip from Anchor Fitting.
The child restraint is now disconnected.
6
For Toddler & Child Use
Fully press Adjuster Button (A)
while pulling Upper Anchorage
Strap (B) to lengthen.
A
Storage
Strap
B
Pull Adjustment
Strap to
remove slack.
SPECIAL FEATURES - TODDLER RESTRAINT
FOR
TODDLER
USE
To be used only in a forward-facing position for a child weighing from 8 kg to 18 kg.
Upper Anchorage Upper Anchorage Adjustable Upper Versa-Tether™ Attachment
Clip & Cover
Storage Strap
Anchorage Strap
Catch
Strap Adjuster
Top (4th) row of
shoulder slots (only
where provided and only
for Child Safety Harness).
Lower 3 rows of Shoulder
slots (for integral harness
height adjustment.
Anchor
Fitting
Fully adjustable
6 point harness.
Sash Locator for
Booster mode shown in
the storage recess.
(See warning on Page 8)
Vehicle lapsash seat belt
or lap belt.
Padded cover
for comfort.
Harness
Adjustment
Button.
Armrests
(where fitted)
Recline Foot in
upright installation
Harness
Adjustment
Strap
Quick release
Harness Buckle.
(Red button)
Harness
Tongues
Harness
Buckle
Front of vehicle
Anti-Submarine clip for
Booster mode. Shown in
storage recess under cover.
(See warning on Page 8)
Cup Holder
1 each side
(where fitted)
Forward Facing (8 kg to 18 kg)
7
FOR
TODDLER
USE
SUITABLE FOR USE
TO BE USED WITH A LAP-SASH OR LAP ONLY SEAT BELT IN THE FRONT OR BACK
OF MOST CARS WITH FORWARD-FACING SEATS.
To be used only in a forward-facing position
for a child weighing from 8 kg to 18kg.
8 kg minimum.
18 kg maximum.
WARNINGS
Fit the restraint firmly to the car seat and then fit the harness firmly to the child.
A loose restraint or harness is dangerous.
Do not use in a front seat, unless it has a child restraint anchorage point ie: utilities.
Do not use the restraint without the Upper Anchorage Strap correctly attached.
Do not use on any vehicle seat which faces sideways or rearwards.
DO NOT USE A CHILD RESTRAINT IN A SEATING POSITION WHERE AN AIRBAG IS FITTED.
FOLLOW THE CAR MANUFACTURER’S RECOMMENDATIONS.
THIS RESTRAINT IS NOT SUITABLE FOR USE IN A HATCHBACK OR WAGON WHERE THE
ANCHORAGE STRAP MAY FALL INTO A SPLIT IN THE SEAT BACK.
IMPORTANT: Use lap or lap-sash seat belt and upper anchorage strap to attach the child
restraint to the vehicle seat.
Ensure that the Sash Locator strap is stored in the recess under the cover to avoid injury or
discomfort to the child.
Ensure that the Anti-Submarine clip is stored in the recess under the cover when the seat is
used in Toddler mode, to avoid injury or discomfort.
NOTE: Some versions of the Maxi Rider have been provided with an extra (4th) row of shoulder
slots, which are only available for use if there are matching slots in the trim (cover). These extra
slots are only for use with the Protecta™ Child Safety Harness and should not be used for the
integral Harness.
8
Forward Facing (8 kg to 18 kg)
FOR
TODDLER
USE
HOW TO SET-UP
ADJUSTING THE BUCKLE POSITION
BUCKLE
POSITION
BUCKLE
POSITION
TOO HIGH
OK
Centre of button on
buckle, level with
top of child's legs
(with all slack
removed from
crotch strap.)
IMPORTANT: You must adjust the crotch strap to the correct length for your child
before installing the restraint as it cannot be adjusted in the car. The crotch strap should only be
extended if the harness tongues are located low against your child's legs, thus creating
discomfort.
Always return the crotch strap to its original shorter length when using the seat with a smaller
child.
The buckle should always be positioned low down on your child's body.
DO NOT attempt to remove the crotch strap from the adjuster. Adjustment is made by feeding the
crotch strap through the adjuster as shown and does not need to be removed from the seat.
SETTING UP THE HARNESS
A. Sit the restraint against a wall for stability and get the child to sit
comfortably in position.
B. Determine the desired shoulder strap position and buckle position.
C. Remove the child and adjust the buckle strap and shoulder straps using
the following methods.
D. Repeat steps A & B to confirm the correct set-up of the built-in harness.
ADJUSTING THE CROTCH BUCKLE STRAP LENGTH
A. Adjust the crotch buckle to the
correct position for your child. It
should be kept as low as possible
to keep the lap straps fully
engaged over the hips. Ensure
that the harness tongues do not
push into your child's thighs as
this will cause discomfort.
B. To change the length of the crotch
strap, thread through the adjuster
in the direction of the arrows
shown.
SHORTEN
LENGTHEN
Forward Facing (8 kg to 18 kg)
9
FOR
TODDLER
USE
HOW TO SETUP
ADJUSTING SHOULDER HARNESS STRAPS HEIGHT
Correct fitment of the harness is very important as it restrains the child in the restraint. The
harness must fit firmly around the upper torso of the child and be
positioned so as to leave the child’s arms and legs free.
8
FOR TODDLER USE: The shoulder straps must be in the slots
which are nearest to the child’s shoulders, but not more than
25mm below the child’s shoulders. If when in the top slots,
the harness straps are more than 25mm below the level of
the child’s shoulders or child weighs more than 18kg, then
the child is too large for the harness straps and the restraint
should be now used as a booster. (Booster Mode - see
pages 15 onwards).
1
2
3
4
6
The shoulder straps must be
in the slots which are
nearest to the child’s
shoulders, but not more
than 25mm below the
child’s shoulders.
Front of vehicle
7
1.
2.
3.
4.
5.
6.
7.
8.
4
5
6
7
Upper shoulder strap slots.
Mid shoulder strap slots.
Lower shoulder strap slots.
Shoulder harness straps.
Harness tongues & buckle.
Lap strap slots.
Crotch strap slots.
Top (4th) row of shoulder slots
(only where provided and only
for Child Safety Harness).
STEPS IN CHANGING SHOULDER STRAP SLOTS
Strap Connector
A. Remove the restraint from vehicle as instructed on page 7.
B. At the rear of the restraint, remove one of the harness
shoulder straps from metal Strap Connector by slipping
strap through open slot. The metal Strap Connector is
shown in diagram right.
C. From the front, pull the shoulder strap out through
shoulder slot.
D. Insert shoulder strap through restraint slot which will
position shoulder strap level with or above the child’s
shoulder, shown above. Ensure that the Shoulder strap
passes through matching slots in cover and restraint body.
E. Ensure there are no twists in the harness strap and the buckle tongues face the
correct way.
F. Connect shoulder strap to metal strap connector at rear of restraint.
G. Repeat for other shoulder strap. It is better to change one strap at a time so that
the other strap will be a guide for re-assembly.
WARNING: Do not use the restraint with harness shoulder straps set at different
heights or fed through mis-matching slots. Ensure harness straps are not
twisted and that all straps are secure by pulling each harness strap.
10
Forward Facing (8 kg to 18 kg)
FOR
TODDLER
USE
HOW TO INSTALL
INSTALLING INTO VEHICLE (FORWARD FACING)
(UPRIGHT OR RECLINED)
A. Determine whether an upright or
reclined installation is preferred as
shown right.
Recline Foot
position
for upright
installation.
UPRIGHT
Recline Foot
position
for reclined
installation.
RECLINED
B. To move the Recline Foot from upright to reclined mode or vice versa. Pull the Foot outwards
to unlock it, then rotate the foot. Push to lock in place. See diagrams below.
Rotate.
Push In
to Lock.
Pull Out.
C. Position restraint centrally to the chosen position in forward facing mode and align restraint
centrally to the chosen seating position as shown on page 14. Some vehicle seat fabrics
(particularly velours) may be damaged by a child
restraint used continuously. We recommend the use
of a thick towel or other protection to keep the
vehicle seat in good condition.
D. Fully lengthen lap or lap sash seat
belt and insert through near seatbelt
slot. Ensure the seatbelt is between
the trim and seat back as you push
the seatbelt out through the far
seatbelt slot.
Seatbelt feeds
through slot in seat
between trim and
seat back.
Engage into
Seatbelt
buckle
Near seatbelt slot.
Far seatbelt slot.
Forward Facing (8 kg to 18 kg)
11
FOR
TODDLER
USE
HOW TO INSTALL
E. Engage car seat belt buckle and
tongue. Push down on the restraint
while pulling on the lap portion to
remove all slack from the belt. Then,
pull the remaining slack in the sash
belt and allow excess belt to feed back
into the retractor.
Remove
Slack
Engage
NOTE: Some vehicle seats have more seatbelt
rearward slope than others. Use a
rolled up towel or padding under the
seat for contoured vehicle seats to
prevent excessive recline.
Vehicle
seat
belt
F. To lengthen the Upper Anchorage
Strap, fully press Adjuster Button (A)
while pulling Upper Anchorage Strap
(B) to slacken as shown below.
A
G. Fit the Attachment Clip to the Anchor
Fitting making sure to remove as many
twists as possible.
Anchor
fitting
B
Attachment
Clip & Cover
Storage
Strap
Pull Adjustment
Strap to remove slack
H. Pull Upper Anchorage Adjustment Strap to remove slack. Fold up excess strap and use
storage strap to neatly store excess strap behind seat. See illustration on following page.
12
Forward Facing (8 kg to 18 kg)
FOR
TODDLER
USE
HOW TO INSTALL
Upper Anchorage Versa-Tether™
Strap
Catch
Anchor
Fitting
Upper Anchorage
Storage Strap
Fully press Adjuster button while
pulling Upper Anchorage strap to
lengthen.
Attachment
Clip & Cover
(4th)
Top
row of shoulder slots
(only where provided and only
for Child Safety Harness).
Ensure Sash locator is in
storage recess (used
for Booster mode only)
Armrests
(where fitted)
Front of vehicle
Recline Foot in
upright installation
Ensure Anti-Submarine
clip is stored in recess
(used for Booster mode only)
Cup Holder
1 each side
(where fitted)
IMPORTANT: Always ensure that the seat belt is correctly restraining the restraint on
the vehicle seat.
Make sure Cup Holders (If fitted) do not interfere with closure of the car door.
Forward Facing (8 kg to 18 kg)
13
FOR
TODDLER
USE
HOW TO USE
PLACING TODDLER IN THE RESTRAINT
A. Lengthen harness by pressing Harness
Adjustment button while pulling on either
shoulder strap until the harness will
accommodate the child.
B. Place child in the restraint and feed
each arm through shoulder straps.
Pull harness buckle up between
child's legs.
Pull to
lengthen
Press & hold
Harness
Adjustment
Button.
Front of vehicle
Pull harness
adjuster strap
to tighten.
C. Fit either harness buckle tongues
into the harness buckle followed
by the other tongue until a click
is heard. Should the second
tongue not insert - press the red
button and reinsert the tongues.
Ensure secure engagement by
pulling harness straps.
Click
D. Ensure slack is removed from harness lap strap by pulling
Pull to remove slack
shoulder straps then pull harness adjustment strap to adjust
from Harness Lap Strap
harness to a comfortable but firm fit. Ensure that any slack in
harness straps is removed. Shoulder Harness Straps must fit
Shoulder
firmly to the child. A loose harness could result in serious injury
Strap
in an accident.
Do not use restraint if straps do not tighten and contact your
Harness
local authorised service agent for repair.
Lap Strap
Crotch Straps
TO REMOVE TODDLER
Press red button on harness buckle then both harness tongues will be released. Lift the
shoulder straps from the child’s shoulders.
14
Forward Facing (8 kg to 18 kg)
SPECIAL FEATURES - CHILD BOOSTER
To be used only with a lap-sash seat belt or with a seat belt and child harness for a child
weighing from 14kg to 26kg.
Upper Anchorage Upper Anchorage Adjustable Upper Versa-Tether™ Attachment
Clip & Cover
Storage Strap
Anchorage Strap.
Catch
Strap Adjuster
Top (4th) row of
shoulder slots (only
where provided and only
for Child Safety Harness).
Anchor
Fitting
Sash locator
Clip and strap
Armrests
(where fitted)
Lap-Sash
Seat Belt
Lap belt Anti
Submarining Clip
(Engaged in
harness buckle)
Harness stored
in recess under
cover trim.
Harness
Adjustment
Button & Strap
Recline Foot in
upright installation.
Padded cover
for comfort.
Cup Holder
1 each side
(where fitted)
Front of vehicle
Forward Facing (14 kg up to 26 kg)
15
SUITABLE FOR USE
THIS RESTRAINT MUST BE USED IN
CARS WITH FORWARD-FACING SEATS
WITH A LAP-SASH SEAT BELT OR WITH A
SEAT BELT AND CHILD HARNESS.
To be used only with a lap-sash seat
belt or with a seat belt and child
harness for a child weighing from 14kg
to 26kg.
14 kg minimum.
26 kg maximum.
WARNINGS
CAUTION: Upper anchorage strap must be used and properly connected at all times.
SUITABLE FOR USE WITH SAFE-N-SOUND PROTECTA™ CHILD SAFETY HARNESS. Not suitable
for use with any other child safety harness.
DO NOT USE WITH JUST A LAP BELT. You must use with a lap-sash belt or with a seat belt and child
harness. If used with a child harness, the lap strap of the seat belt must be adjusted firmly first and then
the harness, so that the lap strap is not lifted off the child’s lap when the harness is adjusted.
Do not use with the integral harness when in booster mode (between 14 to 26kg). This
built in harness must be stored.
Do not use the restraint without the Upper Anchorage Strap correctly attached.
Do not use with just a lap seat belt.
Do not use in a front seat, unless it has a child restraint anchorage point.
Do not use on any vehicle seat which faces sideways or rearwards.
DO NOT USE A CHILD RESTRAINT IN A SEATING POSITION WHERE AN
AIRBAG IS FITTED. FOLLOW THE CAR MANUFACTURER’S
RECOMMENDATIONS.
THIS RESTRAINT IS NOT SUITABLE FOR USE IN A HATCHBACK OR
WAGON WHERE THE ANCHORAGE STRAP MAY FALL INTO A
SPLIT IN THE SEAT BACK.
IMPORTANT: Use lap-sash seat belt to hold the child to the
restraint. Attach the upper anchorage strap. Do not use the inbuilt
harness straps attached to the restraint.
Lap part of
seat belt in
recess area (under armrest).
16
Forward Facing (14 kg up to 26 kg)
HOW TO SETUP
CONVERTING INTO CHILD BOOSTER
To use this child restraint as a booster seat the harness needs to be stored under
the cover.
Upper anchorage strap must be used in booster position.
Do not disengage the upper anchorage strap from the anchor fitting.
Disengage and remove the seat belt from the restraint.
STORING ACCESSORIES IN SEAT RECESS
When used as a Booster seat, the accessories for child use are found in storage
recesses under the cover, as shown below.
Sash Locator
Anti-Submarining
Clip
Place rolled-up Harness Strap
and Harness Tongue in recess
TODDLER USE
CHILD USE with Anti-Submarining Clip
and Sash Locator
STORING THE HARNESS
A. Disengage harness buckle. Fully
lengthen the harness by pressing the
Harness Adjustment Button and pulling
the harness shoulder straps.
B. At the rear of the restraint, remove
both of the harness shoulder straps
from metal Strap Connector by
slipping strap through open slot. The
metal Strap Connector is shown in
diagram below.
Strap Connector
Forward Facing (14 kg up to 26 kg)
17
HOW TO SET-UP
C. Pull the shoulder straps through slots in the seat back.
D. Remove the Elastic loops holding the cover in place at the lower front of the seat. Lift the
cover to expose the storage inserts in the seat base.
E. Remove Sash Locator strap and clip from storage recess and attach to the strap connector
plate as shown below (Make sure straps are not twisted).
F. Then thread the sash guide through the shoulder strap slot nearest your seat belt.
Feed Sash
locator Clip
through
appropriate slot.
G. Feed the straps with harness buckle tongues through the bottom rear of the seat cover. Roll
up the harness straps with harness buckle tongue and place them into the left and right rear
recess in the seat base (underneath the cover).
H. Remove Anti Submarine Clip from storage recess and engage into harness buckle. See page
20.
I. Adjust the crotch strap length if necessary. See page 19.
J. Align cover and re-engage elastic loops at the front of the cover.
K. Store shoulder pads (if fitted) in a safe place, for future use.
18
Forward Facing (14 kg up to 26 kg)
HOW TO SET-UP
SETTING UP THE BUCKLE AND SASH GUIDE
POSITIONS
A. Sit the restraint against a wall for stability and get the child to sit
comfortably in position.
B. Determine the desired buckle position.
C. Determine the correct shoulder slot for the sash guide.
D. Remove the child and adjust the buckle strap using the following method.
E. Repeat steps A & B to confirm the correct set-up of the buckle.
IMPORTANT: You must
adjust the crotch strap to
the correct length for your child
before installing the restraint as it
cannot be adjusted in the car.
The crotch strap should only be
Bottom edge of
extended if the buckle and Antibuckle, level with top
of legs.
Submarine clip are located too
low against your child's legs,
All slack removed from
causing discomfort.
crotch strap when
Always return the crotch strap to
buckle is in correct
position.
its original shorter length when
using the seat with a smaller
child.
The buckle/Anti-Submarine Clip should always be positioned low down on your
child's body.
DO NOT attempt to remove the crotch strap from the adjuster. Adjustment is made by
feeding the crotch strap through the adjuster as shown on page 9.
Forward Facing (14 kg up to 26 kg)
19
HOW TO INSTALL
PLACING CHILD IN THE RESTRAINT
USING LAP SASH SEAT BELT & UPPER ANCHORAGE STRAP ENGAGED
A. Determine whether an upright or
Recline Foot
position
reclined installation is preferred as
for upright
shown below.
installation.
B. To move the Recline Foot from
reclined to upright mode or vice versa
pull the Foot outwards to unlock it, then
rotate the foot. Push to lock in place.
UPRIGHT
Swing the seat back until it sits firmly
on the vehicle seat.
Rotate.
Recline Foot
position
for reclined
installation.
RECLINED
Push In
to Lock.
Pull Out.
C. The restraint is now ready for use as a child booster, ensure the upper
anchorage strap is still engaged (refer to page 6) into the anchor fitting and
remove slack if necessary. Do not overtighten causing the restraint to lift.
D. Sit the child on the restraint.
E. Position the lap-sash belt over the child ensuring the lap portion is positioned
into the lap recess area under the armrest. Fit the Anti Submarining Clip to the
lap belt as shown below. It is recommended that the lap belt Anti-submarining
Clip (if fitted) should be used at all times in Booster mode, to help prevent your
child from submarining in the event of an impact.
F. Engage seat belt buckle and tongue ensuring
there are no twists in the belt. If the seat belt
buckle is adjustable, adjust the buckle as
low as possible away from the child.
Remove AntiSubmarine Clip from
recess area and
engage into harness
buckle.
Click
Hook the Lap Belt Anti Submarining
Clip over the lap belt with the Red
button (of the buckle) facing forward.
Lap part of seat belt in recess
area (under armrest).
NOTE: Some vehicle seats have more rearward slope than others. Use a rolled up towel or
padding under the seat for contoured vehicle seats to prevent excessive recline.
20
Forward Facing (14 kg up to 26 kg)
HOW TO INSTALL
G. The Sash locator must be used to position the sash portion of the lap-sash seat
belt across the child’s shoulders and chest. Choose the shoulder harness
nearest to the shoulder height of the child.
H. Pull sash locator through back of the restraint and then feed it back into your
chosen slot position nearest the sash of the seat belt.
I. Connect the sash of the seat belt to the sash locator clip at shoulder height.
J. Adjust lap and sash portion of seat belt firmly but comfortably across the child’s
lap and chest and then pull the harness adjustment strap to move sash guide so
that the guide sits comfortably over your child's shoulder.
K. If using the Inertia Reel Retractor seat belt, adjust the lap portion of the seat belt
firmly around the child and restraint, then let the slack sash portion retract up
into the sash retractor.
L. If possible, adjust the vehicle seat to improve the position of the sash on the
child’s chest.
M. When not using the restraint, secure in position by engaging the seat belt over
the seat.
IMPORTANT: If fitted, the Anti-Submarining clip should be used when the child is
using the Booster Seat. Always ensure the seat belt is correctly restraining the
child on the restraint.
TO REMOVE CHILD
Disengage seat belt tongue and buckle, remove the lap
portion of seat belt from the Anti Submarining clip,
remove the sash locator from the sash portion of seat
belt and remove belt from child.
When Booster is not being used, secure in
position, by engaging seat belt over the
booster seat.
NOTE: Do not use this Booster
Seat if the child’s eye level is
above the top of the Booster
Seat back or vehicle headrest
(which ever is highest) when the
child is seated.
Forward Facing (14 kg up to 26 kg)
21
USING WITH CHILD HARNESS
(Not Supplied)
USING LAP SASH BELT & PROTECTA™ CHILD SAFETY
HARNESS (If supplied)
?
?
Store in-built harness as detailed on pages 17-18.
Store Sash Guide in recess under cover.
Refer to Protecta™ Child Safety Harness (Series 120) instructions for full details of
using and installing the Protecta™ Child Safety Harness. When installing the harness
into the vehicle, connect the upper anchorage strap to the Versa-Tether™ Catch on
the Maxi Rider™ upper tether strap (as shown below).
Use the extension strap supplied for all other instances to attach the harness to anchor
points in the luggage area such as the vehicle floor or ceiling.
Not suitable for other styles of child safety harnesses.
INSTALLING PROTECTA™ CHILD SAFETY HARNESS INTO
VEHICLE
Hook attachment clip of Harness (1) onto Versa-Tether™ Catch (2). Then hook attachment clip
(3) onto anchor fitting. Ensure that none of the straps are twisted or catching on sharp edges.
1
2
1. Attachment Clip from Harness.
2. Versa-Tether™ Catch.
3. Attachment Clip & Cover.
4. Anchor Fitting.
5. Anchor Bolt.
3
5
4
INSTALLING PROTECTA™ CHILD SAFETY HARNESS WITH
EXTENSION STRAP INTO VEHICLE
Hook the Protecta™ Child Safety Harness clip first onto the extension strap catch,
then hook the extension strap hook onto the Versa-Tether™ Catch on the Maxi
Rider™ upper anchorage strap as shown below. Ensure that none of the straps are
twisted or catching on sharp edges. Tighten Maxi Rider™ Upper anchorage strap
(refer to page 12) then remove excess slack from the extension strap by pulling the
adjuster strap as illustrated below.
Protecta™ Child Safety Harness
Pull to remove
slack
Versa-Tether™
Catch
Upper Anchorage
Strap
Anchor
Fitting
Extension Strap (Supplied with Protecta™ Child Safety Harness)
22
Forward Facing (14 kg up to 26 kg)
USING WITH CHILD HARNESS (Not Supplied)
CHOOSING METHOD OF INSTALLATION
The Protecta™ Child Safety Harness can be installed using either of the following
methods.
Sash Locator
METHOD 1 : Using a lap sash seat belt in
Left Shoulder
& Right Shoulder
conjunction with Gated Slide provided to
Strap with Tongue
convert to lap belt plus upper anchorage strap. Strap with Tongue
METHOD 2 : Using lap seat belt plus upper
anchorage strap.
Before installing the Protecta™ Child Safety
Harness determine which method of
installation is required and follow instructions
carefully.
NOTE: If fitted, the Anti-Submarining clip should
be used when the child is using the booster
seat with the child harness.
When using the Protecta™ Child Safety Harness,
ensure the 'built-in' shoulder harness is rolled up and
Crotch Buckle with AntiSubmarining Clip engaged.
stored in the recesses under the cover. Refer to pages
17-18 on storing the harness. If the Anti-Submarining clip (if fitted) is not being
used, then it, and the crotch buckle must also be stored in the recesses under the
cover. Roll up the metal connector and tuck it into the recess in the recline foot at the
back of the seat.
Important Note: Some vehicle seat belts are too short and you may experience some
difficulty fitting the converted lap-sash around your child. If so, adjust the gated slide
nearer to your child, ideally under the armrest and lap belt recess area, (ensure the
slide does not touch your child). This should provide more belt length to fit your child,
but if the belt still will not fit, try another location in the vehicle, eg. side seat. If the
vehicle belts are still too short, then contact the vehicle manufacturer for advice on
longer seat belts.
B. Pull the LH Harness Strap & Cross Strap
through the opposite shoulder slot. Make
A.Feed the LH Harness Strap & Cross
sure that the Anchor Clip also feeds
Strap through the appropriate
through to the back of the restraint. Hook
shoulder slot.
the Attachment Clip onto the Harness
Catch and ensure that the straps line up to
an equal length.
Feed LH
Harness Strap &
Cross Strap
through
appropriate slot.
Hook the Attachment Clip
onto Versa-Tether™
Catch.
Pull LH Harness
Strap through
opposite slot until
the straps are of
equal length.
Forward Facing (14 kg up to 26 kg)
23
USING WITH CHILD HARNESS
(Not Supplied)
NOTE: Some versions of the Maxi Rider have been provided with an extra (4th) row of
shoulder slots, which are only available for use if there are matching slots in the trim
(cover). These extra slots are only for use with the Protecta™ Child Safety Harness
and should not be used for the integral Harness.
METHOD 1: USING LAP-SASH SEAT BELT WITH
PROTECTA™ CHILD SAFETY HARNESS.
(Using Gated Slide provided with Child
Harness.)
Refer to Protecta™ Child Harness
instruction to fit gated slide.
Converted
lap-sash
seat belt.
Harness
strap loops
Fit the Protecta™ Child
Fit Gated Slide here.
Safety Harness as detailed
on page 23. Then connect the
cross strap as shown below. Thread
the converted lap-sash seat belt
through the harness strap loops
as shown right.
METHOD 2: USING LAP SEAT BELT WITH
PROTECTA™ CHILD SAFETY HARNESS.
Harness
strap loops
Fit the Protecta™ Child Safety Harness as
detailed on page 23. Then connect the
cross strap as shown below. Thread the
lap seat belt through the harness strap
loops as shown right.
Connect the Protecta™ Child Safety Harness to the
Versa-Tether™ Catch as detailed on page 22.
A. With the child seated, place each of the
harness straps over each shoulder.
B. Feed the RH strap (loop end) into
the cross strap loop to connect
Storage
the two sides.
Strap
C.Feed the adult belt (lap belt or
converted lap/sash) through
the harness loops, ensuring
RH Harness
that the cross strap loop does Strap Loop
not disconnect. Also ensure
there are no twists in the
harness, cross strap and
Cross Strap
Loop
seat belt.
Cross Strap
24
Forward Facing (14 kg up to 26 kg)
RH Harness
Strap
LH Harness
Strap
Cover Pad
(Not shown)
USING WITH CHILD HARNESS (Not Supplied)
D.Engage the seat belt tongue to the buckle and adjust the seat belt to sit firmly but
comfortably around the child's pelvis. The seat belt buckle should be located as low as
possible below the child's hip.
Pull Adjustment Strap
to remove slack.
Roll up Adjuster Strap and
secure with Storage Strap.
B
Fully press Adjuster
Button (A) while pulling
Upper Anchorage
Strap (B) to lengthen.
Storage
Strap
A
Adjuster
Adjuster
Cover
E.With the lap belt (or converted lap/sash) adjusted to be a firm fit on the child's
thighs, then adjust the Protecta™ Child Safety Harness to remove all slack in the
shoulder straps. Once adjusted, further adjustments are necessary only to the
upper extension straps and to accommodate the growth of the child.
Use the reverse procedure to remove the child from the harness.
F. Finally, roll up the free end of the adjuster strap, secure using the storage strap,
then place it into the top of the adjuster cover as shown above.
When not in use, the harness may be flipped onto the parcel shelf or disconnected
from the anchor fitting and stored.
WARNING: The lap portion of the belt must be
adjusted firmly first, and then the harness, so
that the belt is not lifted off the child's
lap when the harness is adjusted.
Click
Remove Anti-Submarine Clip
from recess area and engage
into harness buckle.
Engage seat belt buckle and
tongue.
If fitted, fit the Anti Submarining Clip
to the lap belt, centrally between the
shoulder straps of the harness loops,
ensuring that the Red button of the
crotch buckle is facing forward.
Lap portion of belt must be under
armrest on both sides.
Forward Facing (14 kg up to 26 kg)
25
USING WITH CHILD HARNESS
(Not Supplied)
The Protecta™ Child
Safety Harness should always be used
in either the top harness slots or top
child safety harness slots (where
provided).
NOTE: The Child Safety Harness must be in
the slots which are level with or above the
child’s shoulders.
Front of vehicle
FOR LARGE CHILDREN
Once your child's shoulders are above the top slots, then it is suitable to use the protecta™
child safety harness over the top of maxi rider™ seat (see below right).
NOTE: Do not use this Booster Seat if the child’s eye level is above the top of the Booster Seat back
or vehicle headrest (which ever is
highest) when the child is seated.
Eye-line level with
Maxi Rider™ seat
back.
OR
Eye-line level with
car seat headrest if
close enough to
support head from
whiplash is also
permitted provided
shoulder strap
support and child
weight is still within
required limits.
Front of vehicle
RESTORING THE RESTRAINT FOR TODDLER USE
A. Disengage seat belt tongue from buckle and pull seat belt out of harness strap loops.
B. Disconnect the Harness attachment clip from the VersaStrap Connector
Tether™ Catch and feed the LH Harness Strap out the
shoulder slot. Pull the RH harness Strap to remove the
harness off the seat. (Store the Protecta™ Child Safety
Harness in a safe place for later use).
C. Remove the built-in harness from the storage recess under
the cover. Feed crotch strap and shoulder straps through
seat cover.
D. Feed shoulder straps through appropriate shoulder slots in
the seat back and attach to metal Strap Connector as
shown right.
26
Forward Facing (14 kg up to 26 kg)
HOW TO CLEAN
The restraint has a flame retardant cover which is removable for cleaning. Cleaning
instructions are on the care label attached to the cover. When washing cover
engage hook & loop strips together to eliminate other garments being caught.
Ensure to keep strips free of lint to work effectively. Ensure that the inside of the
buckle is free of foreign matter. Cleaning instructions for the buckle are on page
28. Use only mild soap and water to clean all metal and plastic parts of the
restraint. Do not use chemicals or cleaning agents.
TO REMOVE COVER
You do not have to remove the shoulder harness assembly from the restraint. However, you
do need to disconnect the shoulder harness straps from the metal connector at the back of
the restraint (refer to Page 9). Then follow the sequence below A to H to remove the cover.
C. Unhook Elastic Loops.
B. Feed the Shoulder &
Lap Harness Straps
through the cover.
A. Disengage
Harness Tongues
from Harness
Crotch Buckle.
D. Undo
Plastic
Clips.
H. Peel cover
away from
shell.
E. Unclip Trigger Hook
on each side.
G. Feed Crotch Buckle &
harness adjustment button
through slot in cover.
F. Unhook Elastic Loops.
TO REPLACE COVER
A. Fit cover over restraint starting at top, ensure that both back and bottom elastics are at the
back of restraint.
B. Align cover over restraint.
C. Feed shoulder Harness Straps through matching cover slots on the restraint and re-attach
to strap connector at the back of the seat.
D. Feed Crotch Buckle through slot in cover.
E. Feed Harness Adjustment Button through cutout in cover.
F. Re-attach all Plastic Hooks and Elastic Loops as shown above.
G. If refitting for child booster fit the cover with the harness in a stored position and feed sash
locator strap though appropriate slot, refer to page 21.
For Toddler & Child Use
27
CARE AND MAINTENANCE
REGULAR CARE OF THIS RESTRAINT:
Please check the following items regularly to ensure the safety of your child:
A. Check the webbing for fraying.
B. Check that the buckle clicks and is not sluggish or sticky in operation.
C. Ensure there are no cracks in moulding or the plastic moulding.
D. Check the Harness Adjuster is operating and is clamping the webbing.
E. If any part of the restraint is cracked or broken, seek repair immediately or
replace the child restraint.
TO CLEAN HARNESS BUCKLE:
If sticky liquids such as baby formula, fruit juice, etc. get inside your Harness Buckle, it may
become sluggish. An indication of a sluggish Harness Buckle is that you cannot hear a click
when engaging the Harness Tongues. To restore the Harness Buckle to good working order
it needs to be cleaned as follows:
Cover
A. From the underside of the restraint
pull each crotch 3-bar slide then
turn 3-bar slide and push through
each slot to remove the Harness
Buckle from the restraint.
B
Body
3-bar
slide
C
Click
Place the Harness Buckle under warm
(approx. 40 degrees Celsius) running water as
shown below. Let the water run through the
mouth of the buckle for five minutes.
Engage and disengage the Harness
Tongues and Buckles several times until a
strong audible click is heard.
D. If you still cannot hear a strong audible click after engaging the Harness Tongues &
Buckle, then repeat cleaning several times. If the Harness Buckle cannot be returned to
its original working condition then contact Safe-n-Sound.
E. Refit the Harness Buckle to the restraint with the red button facing out & feeding each 3bar slide through appropriate slot
28
For Toddler & Child Use.
ACCESSORIES & FEATURES
WARNING
ONLY USE SAFE-N-SOUND SEAT COVERS THAT ARE DESIGNED AND TESTED FOR
USE WITH THIS PRODUCT.
The following instructions apply to accessories that may
be supplied with this restraint at point of purchase. If
not, a variety of accessories are available from
various retailers of Safe-n-Sound products.
POCKET
(IF FITTED)
The pocket sewn on the trim is designed
for your convenience. It can hold those
necessary items that you need at a
moments notice. e.g Bottle, face
washer, toy etc.
Crotch Pad
Pocket
Caution: If using the pocket to store filled
bottles, please ensure contents are not
contaminated due to prolonged storage.
CROTCH PAD
(IF FITTED)
The Crotch Pad is designed to provide
extra comfort for baby or child and is fitted
to the restraint as follows: Feed Crotch
Buckle through the slot in crotch pad as
shown.
Messy Mat
MESSY MAT™ SEAT PROTECTOR INSTRUCTIONS
(IF
SUPPLIED)
Place ribbed or pocket end of
Long Messy Mat™
Short Messy Mat™
the Messy Mat™ seat
protector on edge of car seat,
smooth back toward seat join
(’A’) and fit in any excess
Messy Mat™ into the join of
Ribs
Ribs
the car seat (’A’).
Hook and loop attachment
referred in some instruction
books, are no longer required
to fit this model of Messy Mat™
‘A’
‘A’
seat protector.
Pockets
Pockets
CAUTION: The pocket
(Where Fitted)
(Where Fitted)
is only for small, light
items. DO NOT overload the pocket with heavy, bulky items as this may
damage the pocket or cause passengers to trip over them.
PADDED INSERT (IF FITTED)
The Padded Insert is designed to snugly support the baby for extra comfort. Simply
place the padded insert on the restraint between Harness straps and the restraint
back. Ensure padded insert is lined up with or below the shoulder straps.
For Toddler & Child Use
29
ACCESSORIES & FEATURES
SHOULDER PADS (IF FITTED)
Shoulder Pads are designed to provide extra comfort for baby or child and are easily fitted to the
shoulder harness straps by:
A. Pull apart fasteners and remove shoulder pads from harness.
B. Re-fit shoulder pads to harness and attach fasteners for use.
COVER
(STYLE MAY VARY)
The cover has been designed to protect your child when seated in the restraint. Care should be
taken if children either eat or drink while in the restraint as some food or drink products may cause
damage or marking to the cover.
IMPORTANT: Do not pull sticky items from covers as the cover may be damaged - soak in water
and gently remove.
HEAD PILLOW
(IF FITTED)
The Head Pillow is designed to snugly support the toddler or child for extra comfort.
Head Pillow straps should be
If fitting Head Pillow for toddler use, fit straps
over the top of the Restraint and
through either pair of Upper Shoulder Strap
through either pair of top slots.
Slots and over the top of the restraint as
Upper Slots
shown right. Slide Head Pillow up or
Head Pillow
suitable for
down to rest above the shoulder strap
straps
Head Pillow straps
slots being used.
CUP HOLDERS (IF FITTED)
The Booster Seat has a cup holder on either
side of the seat. Swing the cup holder out from
the seat to use. Ensure the cup holder and its
contents can not be crushed by the car door.
Fold away when not in use.
WARNING: Only use for holding cups, bottles
and drink cartons. Do not use for hot drinks
30
For Toddler & Child Use.
ARMREST (IF FITTED)
The armrest can be raised to make it
easier to place the child in the seat and
can be in the down position when the child
is seated and secured.
IN CASE OF ACCIDENT
If your restraint has been involved in a severe crash, you should destroy the restraint
even if no damage is obvious. Some insurance companies offer vehicle insurance
which covers or partially covers the replacement of your child restraint. Contact your
insurance company for further details.
Your insurance company may require you to keep the child restraint for assessment,
but do not use the child restraint after a severe crash. To assist you in making an
accident insurance claim cut the following statement and include it with your claim.
NOTICE TO INSURANCE COMPANY
CHILD RESTRAINT INVOLVED IN AN ACCIDENT
All Safe-n-Sound child restraints are manufactured to Australian/New Zealand
Standards AS/NZS1754-2004 which require us to advise users of child
restraints to "Destroy the entire restraint if it has been in use in a severe crash,
even if no damage is obvious". The joint Australian/New Zealand Standards
committee CS/85, advise that this statement applies whether a child was in the
child restraint or not. A severe crash, we consider as being one where the main
body structure of the vehicle is distorted.
There is no method of determining if the restraint has been damaged and we
concur with the Australian/New Zealand Standards in recommending
destruction of the child restraint.
This notice is to advise you of the requirements of the Australian/New Zealand
Standards and our obligation in complying with the standards.
Please assist the owner of this restraint in their claim.
Britax Childcare Pty. Ltd.
(Incorporated in Victoria)
A.B.N 55 006 773 600
Head office and registered address:
99 Derby Road Sunshine Victoria 3020
PO Box 147 Sunshine Victoria 3020
Telephone: 1300 303 330
For Toddler & Child Use
31
The Britax trade mark is the property of Britax
Excelsior Limited-UK.
INSTRUCTION BOOK
The Safe-n-Sound trade mark is the property
of
Britax Childcare Pty. Limited-Australia.
Series Number: 8000/A/2004
We reserve the right to alter this product without notice in our constant
endeavour for improvement.
1997-2008 Britax Childcare Pty. Ltd. This product is covered by Australian and
overseas patent applications. Patents Pending.
Visit the Britax Web Site at http://www.britax.com.au
or Email us at: custserv@britax.com.au
P/No. 2109321/B