01EN_RX-V457_U-cv.fm Page 1 Thursday, May 19, 2005 10:24 AM
U
RX-V457
AV Receiver
© 2005
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WE59830-1
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
10
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1
2
3
4
5
6
7
8
9
i
11
Read Instructions – All the safety and operating instructions
should be read before the product is operated.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions – All operating and use instructions
should be followed.
Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven
surfaces may cause the product and cart
combination to overturn.
12
13
14
15
16
17
18
19
Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
IMPORTANT SAFETY INSTRUCTIONS
d)
20
21
22
23
If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f)
When the product exhibits a distinct change in performance - this indicates a need for service.
Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24
Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
ii
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this sound system in a well ventilated, cool,
dry, clean place – away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
Allow ventilation space of at least 30 cm on the top,
20 cm on the left and right, and 20 cm on the back of
this unit.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this unit
in a environment with high humidity (i.e. a room with
a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed to
liquid dripping or splashing. On the top of this unit,
do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the user
and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified
is dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an electrical
storm.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
15 When not planning to use this unit for long periods
of time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
18 VOLTAGE SELECTOR (Asia and General models
only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage BEFORE
plugging into the AC main supply. Voltages are:
Asia model ..................... 220/230–240 V AC, 50/60 Hz
General model
........................... 110/120/220/230–240 V AC, 50/60 Hz
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet, even
if this unit itself is turned off. This state is called the
standby mode. In this state, this unit is designed to
consume a very small quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound
come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing.
iii
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
CONTENTS
INTRODUCTION
INTRODUCTION
SOUND FIELD PROGRAMS
FEATURES............................................................. 2
GETTING STARTED............................................ 3
SOUND FIELD PROGRAM
DESCRIPTIONS...............................................49
Supplied accessories .................................................. 3
Installing batteries in the remote control ................... 3
For movie/video sources.......................................... 49
For music sources .................................................... 51
CONTROLS AND FUNCTIONS ......................... 4
ADVANCED OPERATION
PREPARATION
Front panel ................................................................. 4
Remote control........................................................... 6
Using the remote control ........................................... 7
Front panel display .................................................... 8
Rear panel ................................................................ 10
ADVANCED OPERATIONS ..............................52
Using the sleep timer ............................................... 52
Manually adjusting speaker levels........................... 53
SET MENU ............................................................54
PREPARATION
SPEAKER SETUP ............................................... 11
Speaker placement ................................................... 11
Speaker connections ................................................ 12
CONNECTIONS .................................................. 14
BASIC SETUP ...................................................... 22
ADVANCED SETUP MENU...............................61
REMOTE CONTROL FEATURES ...................63
BASIC
OPERATION
Before connecting components................................ 14
Connecting video components................................. 15
Connecting audio components................................. 18
Connecting the FM and AM antennas ..................... 19
Connecting the power supply cord .......................... 20
Speaker impedance setting ...................................... 21
Turning on the power............................................... 21
Using SET MENU................................................... 55
1 SOUND MENU.................................................... 56
2 INPUT MENU...................................................... 58
3 OPTION MENU................................................... 59
Control area ............................................................. 63
Setting remote control codes ................................... 64
Controlling other components ................................. 65
Switching library codes ........................................... 66
Clearing set up remote control codes....................... 66
ADDITIONAL INFORMATION
Using the BASIC SETUP menu .............................. 22
BASIC OPERATION
PLAYBACK.......................................................... 25
Basic operations....................................................... 25
Selecting sound field programs ............................... 27
Selecting input modes.............................................. 31
FM/AM TUNING ................................................. 33
XM SATELLITE RADIO TUNING .................. 39
What is a sound field ............................................... 67
Changing parameter settings ................................... 67
SOUND FIELD PARAMETER
DESCRIPTIONS...............................................69
TROUBLESHOOTING .......................................71
RESETTING THE FACTORY PRESETS ........75
GLOSSARY...........................................................76
Audio formats .......................................................... 76
Sound field programs............................................... 77
Audio information ................................................... 77
Video signal information ......................................... 78
ADVANCED
OPERATION
Automatic and manual tuning.................................. 33
Presetting stations .................................................... 34
Selecting preset stations........................................... 36
Exchanging preset stations ...................................... 37
SOUND FIELD
PROGRAMS
EDITING SOUND FIELD PARAMETERS ......67
SPECIFICATIONS...............................................79
ADDITIONAL
INFORMATION
What is XM Satellite Radio? ................................... 39
XM Satellite Radio connections .............................. 39
XM Satellite Radio functions .................................. 39
Activating XM Satellite Radio ................................ 40
Basic XM Satellite Radio operations....................... 41
XM Satellite Radio search modes............................ 42
Setting XM Satellite Radio preset channels ............ 45
RECORDING ....................................................... 48
1
FEATURES
FEATURES
Built-in 6-channel power amplifier
Sophisticated AM/FM tuner
◆ Minimum RMS output power
(0.06% THD, 20 Hz to 20 kHz, 8 Ω)
Front: 85 W + 85 W
Center: 85 W
Surround: 85 W + 85 W
Surround back: 85 W
◆ 40-station random and direct preset tuning
◆ Automatic preset tuning
◆ Preset station shifting capability (preset editing)
Sound field features
◆ Proprietary YAMAHA technology for the creation of
sound fields
◆ Dolby Digital/Dolby Digital EX decoder
◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6,
DTS 96/24 decoder
◆ Dolby Pro Logic/Dolby Pro Logic II/
Dolby Pro Logic IIx decoder
◆ Virtual CINEMA DSP
◆ SILENT CINEMA™
XM Satellite Radio
◆ XM Satellite Radio programming (using the “XM
Connect and Play digital antenna accessory”, sold
separately)
Other features
◆ 192-kHz/24-bit D/A converter
◆ A SET MENU that provides you with items for
optimizing this unit for your audio/video system
◆ 6 additional input jacks for discrete multi-channel input
◆ S-video signal input/output capability
◆ Component video input/output capability
◆ Optical and coaxial digital audio signal jacks
◆ Sleep timer
◆ Cinema and music night listening modes
◆ Remote control with preset remote control codes
• y indicates a tip for your operation.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and product, the product has priority.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol
are trademarks of Dolby Laboratories.
“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of
Digital Theater Systems, Inc.
“SILENT CINEMA” is a trademark of YAMAHA
CORPORATION.
The XM name and related logos are registered trademarks of XM
Satellite Radio Inc.
2
GETTING STARTED
GETTING STARTED
INTRODUCTION
Supplied accessories
Please check that you received all of the following parts.
Remote control
CODE SET
TRANSMIT
Batteries (4)
(AAA, R03, UM-4)
SYSTEM
POWER
POWER
STANDBY
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
AM loop antenna
75-ohm/300-ohm antenna
adapter (U.K. model only)
AMP
VCR
TV VOL
TV CH
TV MUTE
TV INPUT
STEREO
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
VOLUME
MUTE
A SPEAKERS B
9
0
10
MOVIE
ENT.
Indoor FM antenna
(U.S.A., Canada, China, Asia
and General models)
EFFECT
LEVEL
PRESET/CH
SET MENU
TITLE
MENU
BAND
SRCH MODE
ENTER
A-E/CAT.
RETURN
Indoor FM antenna
(U.K., Europe, Australia
and Korea models)
A-E/CAT.
DISPLAY
MEMORY
REC
AUDIO
DISC SKIP
Installing batteries in the remote
control
2
1
3
1
Press the
part and slide the battery
compartment cover off.
2
Insert four supplied batteries (AAA, R03,
UM-4) according to the polarity markings
(+ / –) on the inside of the battery
compartment.
3
Slide the cover back until it snaps into place.
Notes on batteries
• Change all of the batteries if you notice the following
conditions; the operation range of the remote control decreases,
the indicator does not flash or its light becomes dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the remote control code and program
any acquired functions that may have been cleared.
3
CONTROLS AND FUNCTIONS
CONTROLS AND FUNCTIONS
Front panel
1
2
34 5
6
7
8
9
0
A
(U.S.A. model)
VOLUME
STANDBY
/ON
PRESET/TUNING
FM/AM
XM
SEARCH MODE
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
B
C
DE
F
G
1 STANDBY/ON
Turns on this unit or sets it to the standby mode. When you
turn on this unit, you will hear a click and there will be a 4
to 5-second delay before this unit can reproduce sound.
Note
In standby mode, this unit consumes a small amount of power in
order to receive infrared-signals from the remote control.
2 Remote control sensor
Receives signals from the remote control.
3 Front panel display
Shows information about the operational status of this unit.
4 PRESET/TUNING (EDIT), SEARCH MODE*
Switches the function of PRESET/TUNING/CH l / h
(LEVEL –/+) between selecting preset station numbers
and tuning.
5 FM/AM, XM*
Switches the reception band when the unit is in tuner
mode.
4
H
I
L
AUDIO
R
J
6 A/B/C/D/E, NEXT, CATEGORY*
Selects one of the 5 preset station groups (A to E) when
the unit is in tuner mode.
Selects the speaker channel to be adjusted when the unit is
not in tuner mode.
7 PRESET/TUNING/ CH* l / h, LEVEL –/+
Selects preset station number 1 to 8 when the colon (:) is
displayed next to the band indication in the front panel
display when the unit is in tuner mode. Selects the tuning
frequency when the colon (:) is not displayed.
Adjusts the level of the speaker channel selected using
A/B/C/D/E (NEXT) when the unit is not in tuner mode.
8 MEMORY (MAN’L/AUTO FM)
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.
9 TUNING MODE (AUTO/MAN’L MONO),
DISPLAY*
Switches between automatic tuning (AUTO indicator on)
and manual tuning (AUTO indicator off).
CONTROLS AND FUNCTIONS
INTRODUCTION
0 VIDEO AUX jacks
Input audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input source.
A VOLUME
Controls the output level of all audio channels.
This does not affect the REC OUT level.
B
PHONES (SILENT CINEMA) jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the OUTPUT jacks or to the speakers.
All Dolby Digital and DTS audio signals are mixed down
to the left and right headphone channels.
C SPEAKERS A/B
Turns on or off the set of front speakers connected to the A
and/or B terminals on the rear panel each time the
corresponding button is pressed.
D STRAIGHT (EFFECT)
Switches the sound fields off or on. When STRAIGHT is
selected, input signals (2-channel or multi-channel) are
output directly from their respective speakers without
effect processing.
E TONE CONTROL
Use to adjust the bass/treble balance for the front left and
right speakers (see page 26).
F BASS/TREBLE –/+
Use to adjust the bass/treble balance for the front left and
right speakers (in conjunction with CONTROL).
G PROGRAM l / h
Use to select sound field programs (see page 26).
H INPUT MODE
Sets the priority (AUTO, DTS, ANALOG) for the type of
signals received when one component is connected to two
or more of this unit’s input jacks (see page 31).
I INPUT selector
Selects the input source you want to listen to or watch.
J MULTI CH INPUT
Selects the source connected to the MULTI CH INPUT
jacks. When selected, the MULTI CH INPUT source takes
priority over the source selected with INPUT (or the input
selector buttons on the remote control).
* Available only when the unit is in the XM Satellite Radio mode
(see page 39).
5
CONTROLS AND FUNCTIONS
Remote control
This section describes the function of each control on the
remote control used to control this unit. To operate other
components, see “REMOTE CONTROL FEATURES” on
page 63.
1
2
3
CODE SET
TRANSMIT
SYSTEM
STANDBY
POWER
MD/CD-R
TUNER
SLEEP
DTV/CBL
V-AUX
MULTI CH IN
POWER
POWER
TV
AV
CD
DVD
0
2 CODE SET
Use to set up remote control codes (see page 64).
A
3 Input selector buttons
Select the input source and change the control area.
B
C
D
AMP
VCR
E
F
TV VOL
TV CH
TV MUTE
TV INPUT
VOLUME
G
MUTE
4
5
6
7
STEREO
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
A SPEAKERS B
9
7
8
STRAIGHT
0
10
ENT.
H
EFFECT
LEVEL
PRESET/CH
TITLE
SET MENU
MENU
SRCH MODE
BAND
8
9
MOVIE
NIGHT
ENTER
A-E/CAT.
RETURN
A-E/CAT.
DISPLAY
MEMORY
REC
AUDIO
DISC SKIP
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
I
4 Sound field program/numeric buttons
Use to select sound field programs.
Use numbers 1 through 8 to select preset stations when the
unit is in tuner mode.
Use SELECT to playback 2-channel sources in surround
(see page 29).
Use EXTD SUR. to switch between 5.1 or 6.1-channel
playback of multi-channel software (see page 28).
Use DIRECT ST. to playback 2-channel sources in high
fidelity sound (see page 30).
5 SPEAKERS A/B
Use to turn on or off the set of front speakers connected to
the A and/or B terminals on the rear panel each time the
corresponding button is pressed.
6 NIGHT
Turns on or off the night listening modes (see page 30).
7 LEVEL, BAND
Selects the speaker channel to be adjusted and sets the
level.
Switches the reception band when the unit is in tuner
mode.
8 Cursor buttons u / d / j / i /ENTER
Use to select and adjust sound field program parameters or
SET MENU items.
Press j / i to select a preset station group (A to E) when
the unit is in tuner mode.
Press u / d to select a preset station number (1 to 8)
when the unit is in tuner mode.
9 RETURN, MEMORY*
Returns to the previous menu level when adjusting the
SET MENU parameters.
0 TRANSMIT indicator
Flashes while the remote control is sending signals.
A STANDBY
Sets this unit in the standby mode.
6
CONTROLS AND FUNCTIONS
B SYSTEM POWER
Turns on the power of this unit.
D MULTI CH IN
Selects multi-channel input when using an external
decoder (etc.).
E AMP
Selects the AMP mode. You must select the AMP mode to
control the main unit.
F VOLUME +/–
Increases or decreases the volume level.
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
VOLUME
STANDBY
/ON
CATEGORY
PRESET/TUNING
FM/AM
XM
SEARCH MODE
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
30
30
CODE SET
L
AUDIO
R
Approximately 6 m (20 ft)
TRANSMIT
SYSTEM
POWER POWER STANDBY POWER
TV
CD
G MUTE
Mutes the sound. Press again to restore the audio output to
the previous volume level.
DVD
AV
MD/CD-R TUNER
SLEEP
DTV/CBL V-AUX MULTI CH IN
VCR
AMP
TV VOL
TV CH
TV MUTE
TV INPUT
STEREO
MUSIC
1
2
VOLUME
MUTE
ENTERTAIN MOVIE
3
4
STANDARD SELECT EXTD SUR. DIRECT ST.
5
6
A SPEAKERS B
9
8
7
NIGHT
0
10
STRAIGHT
ENT.
EFFECT
LEVEL
PRESET/CH
TITLE BAND
SET MENU
FAVOR. MENU
A/B/C/D/E
ENTER
CATEGORY
RETURN ALL CH
CATEGORY
DISPLAY
REC
AUDIO
DISC SKIP
H STRAIGHT (EFFECT), ENT.*
Switches the sound fields off or on. When STRAIGHT is
selected, input signals (2-channel or multi-channel) are
output directly from their respective speakers without
effect processing.
I SET MENU, SRCH MODE*
Activates the SET MENU function.
* Available only when the unit is in the XM Satellite Radio mode
(see page 39).
■ Handling the remote control
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– places of high humidity, such as near a bath
– high temperature, such as near a heater or stove
– extremely low temperatures
– dusty places
7
INTRODUCTION
C SLEEP
Sets the sleep timer.
Using the remote control
CONTROLS AND FUNCTIONS
Front panel display
1
t
2
96
24
MATRIX DISCRETE
q DIGITAL
3
VCR
q PL
q PL
q PL x
5
V-AUX
6
DTV/CBL
7
DVD
8
MD/CD-R
90
TUNER
SP
AB
HiFi DSP
XM PTY HOLD PS PTY RT CT EON
SLEEP
dB
ft 96/24
DUAL L C R
mS LFE SL SB SR
dB
D
E
F G
1 Decoder indicators
When any of this unit’s decoders function, the respective
indicator lights up.
2 VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 31).
3 SILENT CINEMA indicator
Lights up when headphones are connected and a sound
field program is selected (see page 26).
4 Input source indicators
A cursor lights to show the current input source.
5 Sound field indicators
Light to indicate the active DSP sound fields.
Presence DSP sound field
Listening position
Left surround
DSP sound field
Right surround
DSP sound field
Surround back DSP sound field
6 CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound field
program.
7 AUTO indicator
Lights up to indicate that automatic tuning is possible.
8 TUNED indicator
Lights up when this unit is tuned into a station.
9 STEREO indicator
Lights up when this unit is receiving a strong signal for an
FM stereo broadcast while the AUTO indicator is lit.
8
B
CD
PCM
C
A
YPAO HD AUTO TUNED STEREO MEMORY MUTE VOLUME
VIRTUAL SILENT CINEMA
STANDARD ZONE2 NIGHT
q EX
4
H
I
J KL
M
0 MEMORY indicator
Flashes to show that a station can be stored.
A MUTE indicator
Flashes while the MUTE function is on.
B VOLUME level indication
Indicates the current volume level.
C PCM indicator
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) digital audio signals.
D STANDARD indicator
Lights up when Surround Standard or Surround Enhanced
is selected (see page 29).
E NIGHT indicator
Lights up when you select night listening mode.
F SP A B indicators
Light up according to the set of front speakers selected.
Both indicators light up when both sets of speakers are
selected.
G Headphones indicator
Lights up when headphones are connected.
H HiFi DSP indicator
Lights up when you select a HiFi DSP sound field
program.
I Multi-information display
Shows the current sound field program name and other
information when adjusting or changing settings.
J SLEEP indicator
Lights up while the sleep timer is on.
CONTROLS AND FUNCTIONS
K 96/24 indicator
Lights up when a DTS 96/24 signal is input to this unit.
INTRODUCTION
L LFE indicator
Lights up when the input signal contains the LFE signal.
M Input channel indicators/speaker indicators
Indicate the channel components of the current digital
input signal.
Indicate the number of speakers connected in SPEAKERS
(page 23), or indicate the channel being adjusted in SP
LEVEL (page 57).
9
CONTROLS AND FUNCTIONS
Rear panel
1
2
4
3
5
COMPONENT VIDEO
Y
PB
PR
DVD
MULTI CH INPUT
R
L
AUDIO
R
VIDEO
L
FRONT
OPTICAL
S VIDEO
DTV/
CBL
XM
SWITCHED
TUNER
CENTER
SUB
WOOFER
IN
VCR
DVD
DTV/CBL
AM
ANT
OUT
CD
GND
IN
(PLAY)
MD/
CD-R
CD
COAXIAL
AC OUTLETS
MONITOR
OUT
DTV/
CBL
SURROUND
DIGITAL
INPUT
VIDEO
DVD
VIDEO
OUT
(REC)
SUB
WOOFER
AUDIO
R
FRONT
– –
SPEAKERS
L
+ +
R
SURROUND
– –
L
+
S VIDEO
75Ω UNBAL.
MONITOR OUT
FM
ANT
L
R
+
A
OUTPUT
B
+
– –
– –
+ +
CENTER
+
SURROUND
BACK
(U.S.A. model)
6
7
8
9
1 DIGITAL INPUT jacks
See pages 15, 17 and 18 for details.
7 SUBWOOFER OUTPUT jack
See page 13 for connection information.
2 MULTI CH INPUT jacks
See page 16 for connection information.
8 Antenna terminals
See page 19 for connection information.
3 Video component jacks
See pages 15 and 17 for connection information.
9 Speaker terminals
See page 13 for connection information.
4 XM jack
See page 39 for connection information.
■ Asia and General models only
5 AC OUTLET(S)
Use to supply power to your other A/V components (see
page 20).
6 Audio component jacks
See page 18 for connection information.
10
VOLTAGE SELECTOR
See page 20.
SPEAKER SETUP
SPEAKER SETUP
Surround speakers (SR and SL)
Speaker placement
The speaker layout below shows the standard ITU-R*
speaker setting. You can use it to enjoy CINEMA DSP and
multi-channel audio sources.
* ITU-R is the radio communication sector of the ITU
(International Telecommunication Union).
C
FR
30˚
SL
SR
60˚
SL
80˚
SR
SB
Surround back speaker (SB)
The surround back speaker supplements the surround
speakers and provides for more realistic front-to-back
transitions. Place this speaker directly behind the listening
position and at the same height as the surround speakers.
Subwoofer
The use of a subwoofer, such as the YAMAHA Active
Servo Processing Subwoofer System, is effective not only
for reinforcing bass frequencies from any or all channels,
but also for high fidelity reproduction of the LFE (lowfrequency effect) channel included in Dolby Digital and
DTS software. The position of the subwoofer is not so
critical, because low bass sounds are not highly
directional. But it is better to place the subwoofer near the
front speakers. Turn it slightly toward the center of the
room to reduce wall reflections.
1.8 m (6 ft)
Front speakers (FR and FL)
The front speakers are used for the main source sound plus
effect sounds. Place these speakers an equal distance from
the ideal listening position. The distance of each speaker
from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds
(dialog, vocals, etc.). If for some reason it is not practical
to use a center speaker, you can do without it. Best results,
however, are obtained with the full system. Align the front
face of the center speaker with the front face of your video
monitor. Place the speaker centrally between the front
speakers and as close to the monitor as possible, such as
directly over or under it.
11
PREPARATION
FL
The surround speakers are used for effect and surround
sounds. Place these speakers behind your listening
position, facing slightly inwards, about 1.8 m (6 ft) above
the floor.
SPEAKER SETUP
Speaker connections
5
Tighten the knob to secure the wire.
Be sure to connect the left channel (L), right channel (R),
“+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the
polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
3
4
5
CAUTION
• If you will use 4 or 6 ohm speakers, be sure to
set this unit’s speaker impedance setting to 4
ohms before using (see page 21).
• Before connecting the speakers, make sure that the
power of this unit is off.
• Do not let the bare speaker wires touch each other or do
not let them touch any metal part of this unit. This
could damage this unit and/or speakers.
• Use magnetically shielded speakers. If this type of
speakers still creates the interference with the monitor,
place the speakers away from the monitor.
A speaker cord is actually a pair of insulated cables
running side by side. One cable is colored or shaped
differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+” (red)
terminals on this unit and your speaker. Connect the plain
cable to the “–” (black) terminals.
Red: positive (+)
Black: negative (–)
■ Banana plug connections
(With the exception of U.K., Europe and Asia models)
First, tighten the knob and then insert the banana plug
connector into the end of the corresponding terminal.
Banana plug
(With the exception of U.K., Europe
and Asia models)
10 mm (3/8")
1
2
1
Remove approximately 10 mm (3/8") of
insulation from the end of each speaker
cable.
2
Twist the exposed wires of the cable together
to prevent short circuits.
3
Unscrew the knob.
4
Insert one bare wire into the hole in the side
of each terminal.
12
SPEAKER SETUP
Front speakers (A)
Right
Left
Subwoofer
system
Surround speakers
Right
Left
1
2
3
6
7
PREPARATION
+
FRONT
R
– –
SPEAKERS
L
R
+ +
SURROUND
– –
L
+
A
SUB
WOOFER
B
OUTPUT
+
– –
– –
+ +
+
SURROUND
BACK
CENTER
(U.S.A. model)
Front
speakers
(B)
4
5
Center
speaker
Surround back
speaker
■ FRONT terminals
Connect one or two speaker systems (2, 3) to these
terminals. If you use only one speaker system, connect it
to the FRONT A or B terminals.
■ CENTER terminals
4
Connect a center speaker (4) to these terminals.
■ SURROUND terminals
2
1
6
3
Connect surround speakers (6, 7) to these terminals.
■ SUBWOOFER jack
7
5
Connect a subwoofer with built-in amplifier (1), such as
the YAMAHA Active Servo Processing Subwoofer
System, to this jack.
■ SURROUND BACK terminals
Speaker layout
Connect a surround back speaker (5) to these terminals.
13
CONNECTIONS
CONNECTIONS
Before connecting components
CAUTION
Do not connect this unit or other components to the mains
power until all connections between components are
complete.
Dust protection cap
Pull out the cap from the optical jack before you connect
the fiber optic cable. Do not discard the cap. When you are
not using the optical jack, be sure to put the cap back in
place. This cap protects the jack from dust.
■ Cable indications
■ Video jacks
For analog signals
left analog cables
L
right analog cables
R
This unit has three types of video jacks. Connection
depends on the availability of input jacks on your monitor.
For digital signals
optical cables
O
coaxial cables
C
video cables
V
S-video cables
S
PR
PB
Y
■ Analog jacks
You can input analog signals from audio components by
connecting audio pin cable to the analog jacks on this unit.
Connect red plugs to the right jacks and white plugs to the
left jacks.
S VIDEO jacks
For S-video signals, separated into luminance (Y) and
color (C) video signals to achieve high-quality color
reproduction.
COMPONENT VIDEO jacks
For component signals, separated into luminance (Y) and
color difference (PB, PR) to provide the best quality in
picture reproduction.
Signal flow inside this unit
Input
■ Digital jacks
This unit has digital jacks for direct transmission of digital
signals through either coaxial or fiber optic cables. You
can use the digital jacks to input PCM, Dolby Digital and
DTS bitstreams. When you connect components to both
the COAXIAL and OPTICAL jacks, priority is given to
the input signals from the COAXIAL jack. All digital
input jacks are compatible with 96-kHz sampling digital
signals.
Note
This unit handles digital and analog signals independently. Thus
audio signals input to the analog jacks are only output to the
analog OUT (REC) jacks.
14
COMPONENT VIDEO
PR
PB
Y
VIDEO jacks
For conventional composite video signals.
For video signals
component video cables
S VIDEO
VIDEO
COMPONENT
VIDEO
S VIDEO
VIDEO
Output
(MONITOR OUT)
CONNECTIONS
Connecting video components
■ Connections for DVD playback
Note
Be sure to connect your video source components in the same way you connect your video monitor to this unit. For example, if you
connect your video monitor to this unit using a VIDEO connection, connect your video source components to this unit using the VIDEO
connections.
PREPARATION
Video out
Optical out
DVD player
Audio out
R
O
L
V
PR
S
PB
Y
COMPONENT VIDEO
Y
PB
PR
DVD
AUDIO
R
VIDEO
L
VIDEO
S VIDEO
DVD
MONITOR
OUT
Video in
Video
monitor
DIGITAL
INPUT
OPTICAL
DVD
VIDEO
S VIDEO
MONITOR OUT
(U.S.A. model)
15
CONNECTIONS
■ Connecting to the MULTI CH INPUT jacks
This unit is equipped with 6 additional input jacks (left and right FRONT, CENTER, left and right SURROUND and
SUBWOOFER) for discrete multi-channel input from a multi-format player, external decoder, sound processor or preamplifier.
Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to
match the left and right outputs to the left and right input jacks for the front and surround channels.
(U.S.A. model)
MULTI CH INPUT
R
L
FRONT
SURROUND
CENTER
SUB
WOOFER
R
L
Subwoofer
out
R
L
Center
out
Front
out
Multi-format player/
External decoder
Surround
out
Notes
• When you select MULTI CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you
cannot select sound field programs.
• This unit does not redirect signals input to the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that
you connect at least a 5.1-channel speaker system before using this feature.
• When headphones are used, only front left and right channels are output.
16
CONNECTIONS
■ Connections for other video components
Note
• Be sure to connect your video source components in the same way you connect your video monitor to this unit. For example, if you
connect your video monitor to this unit using a VIDEO connection, connect your video source components to this unit using the
VIDEO connection.
• Video signals are only output to the MONITOR OUT jacks. When recording, you must make the same type of video connections (i.e.,
S-video) between each component.
Optical out
Video out
Cable TV or
satellite tuner
PREPARATION
Audio out
O
R
L
V
PR
S
PB
Y
(U.S.A. model)
COMPONENT VIDEO
Y
PB
PR
AUDIO
VIDEO
L
R
VIDEO
S VIDEO
DTV/
CBL
Video in
MONITOR
OUT
DTV/
CBL
Video
monitor
DIGITAL
INPUT
OPTICAL
IN
VCR
OUT
DTV/CBL
VIDEO
S VIDEO
MONITOR OUT
R
L
R
V
L
Audio in
Audio out
DVD recorder
or VCR
S
V
S
Video in
Video out
■ VIDEO AUX jacks (on the front panel)
Use these jacks to connect any video source, such as a
game console or video camera, to this unit.
17
CONNECTIONS
VIDEO AUX
VIDEO
L
V
L
AUDIO
R
R
Audio out R
Audio out L
Game
console or
video camera
Video out
Connecting audio components
■ Connections for audio components
DIGITAL
INPUT
Audio out
L
CD player
R
CD
IN
(PLAY)
Coaxial out
MD/
CD-R
C
OUT
(REC)
CD
COAXIAL
L
R
AUDIO
(U.S.A. model)
R
L
R
Audio out
Audio in
MD recorder or
tape deck
18
L
CONNECTIONS
Connecting the FM and AM
antennas
Both FM and AM indoor antennas are included with this
unit. In general, these antennas should provide sufficient
signal strength. Connect each antenna correctly to the
designated terminals.
AM loop antenna
(included)
Indoor FM antenna
(included)
3
Orient the AM loop antenna
for the best reception.
Notes
TUNER
AM
ANT
GND
75Ω UNBAL.
FM
ANT
Ground (GND terminal)
For maximum safety and minimum interference,
connect the antenna GND terminal to a good earth
ground. A good earth ground is a metal stake driven
into moist earth.
■ Connecting the AM loop antenna
1
Set up the AM loop antenna, then connect it
to the terminals on this unit.
2
Press and hold the tab to insert
the AM loop antenna lead wires
into the AM ANT and GND
terminals.
19
PREPARATION
• The AM loop antenna should be placed away from this unit.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
• A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality, an
outdoor antenna may improve the quality. Consult the nearest
authorized YAMAHA dealer or service center about outdoor
antennas.
CONNECTIONS
Connecting the power supply cord
■ Connecting the AC power cord
■ Memory back-up
Plug the power cord into an AC wall outlet.
The memory back-up circuit prevents the stored data from
being lost even if this unit is in the standby mode.
However if the power cord is disconnected from the AC
wall outlet, or the power supply is cut for more than one
week, the stored data will be lost.
■ AC OUTLET(S) (SWITCHED)
U.K. and Australia models .................................... 1 outlet
Korea model ...............................................................None
Other models .........................................................2 outlets
Use these outlets to connect the power cords from your
other components to this unit. Power to the AC
OUTLET(S) is controlled by this unit’s STANDBY/ON
(or SYSTEM POWER and STANDBY). The outlet(s)
supply power to any connected component whenever this
unit is turned on. For information on the maximum power
(total power consumption of components), see
“SPECIFICATIONS” on page 79.
■ VOLTAGE SELECTOR
(Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC main supply. Voltages are:
Asia model ......................... 220/230–240 V AC, 50/60 Hz
General model ..... 110/120/220/230–240 V AC, 50/60 Hz
VOLTAGE SELECTOR
VOLTAGE
SELECTOR
(Asia and General models)
20
CONNECTIONS
Speaker impedance setting
Turning on the power
When all connections are complete, turn on the power of
this unit.
CAUTION
If you are using 4 or 6 ohm speakers, set the impedance to
4 or 6 ohms as follows before turning on the power.
(U.S.A. model)
VOLUME
Be sure this unit is in the standby mode.
STANDBY
/ON
1
PRESET/TUNING
FM/AM
XM
SEARCH MODE
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
l
h
PROGRAM
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
L
AUDIO
R
PREPARATION
Turn off the power to this unit, and while
holding down STRAIGHT (EFFECT), press
STANDBY/ON.
This unit turns on, and the ADVANCED SETUP
menu appears in the front panel display.
STANDBY/ON
STRAIGHT
EFFECT
While holding
down, press
CODE SET
STANDBY
/ON
TRANSMIT
SYSTEM
POWER
POWER
TV
AV
STANDBY
SYSTEM POWER
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
AMP
VCR
2
Press PROGRAM l / h to move through the
menu and select “SP IMP.”.
l
PROGRAM
POWER
TV VOL
TV CH
TV MUTE
TV INPUT
VOLUME
h
Press STANDBY/ON (or SYSTEM POWER on the
remote control) to turn on the power of this unit.
3
Press STRAIGHT (EFFECT) repeatedly to
select “4Ω MIN”.
STRAIGHT
SYSTEM
POWER
STANDBY
/ON
Front panel
or
Remote control
EFFECT
4
Press STANDBY/ON to turn off the power.
STANDBY
/ON
The setting you made is reflected the next time this unit's
power is turned on.
21
BASIC SETUP
BASIC SETUP
The basic setup feature is a useful way to set up your
system quickly and with minimal effort.
3
Press ENTER to enter BASIC SETUP.
y
PRESET/CH
• If you wish to configure the unit manually using more precise
adjustments, use the detailed parameters in SOUND MENU
(page 56) instead of using BASIC SETUP.
• Altering any parameters in BASIC SETUP will reset all
parameters in SOUND MENU.
• Initial settings are indicated in bold for each parameter.
ENTER
The ROOM parameter appears in the front panel
display.
Using the BASIC SETUP menu
Before you begin:
• Press SPEAKERS A or B on the front panel (or press
AMP to select the AMP mode, then press SPEAKERS
A or B on the remote control) to select the front
speakers you want to use.
• Make sure you disconnect your headphones from this
unit.
CODE SET
TRANSMIT
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
4
ROOM: S M >L
Select the size of the room you have installed your
speakers in. In general, the room sizes are defined as
follows:
[U.S.A. and Canada models]
S (small)
16 x 13ft, 200ft2 (4.8 x 4.0m, 20m2)
M (medium) 20 x 16ft, 300ft2 (6.3 x 5.0m, 30m2)
L (large)
26 x 19ft, 450ft2 (7.9 x 5.8m, 45m2)
SYSTEM
STANDBY
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
POWER
POWER
A SPEAKERS B
9
0
10
PRESET/CH
TITLE
1
SET MENU
MENU
BAND
SRCH MODE
ENTER
AMP
VCR
ENT.
EFFECT
LEVEL
A-E/CAT.
RETURN
A-E/CAT.
DISPLAY
2
3-13
MEMORY
[Other models]
S (small)
3.6 x 2.8m, 10m2
M (medium) 4.8 x 4.0m, 20m2
L (large)
6.3 x 5.0m, 30m2
REC
AUDIO
1
TV VOL
TV CH
TV MUTE
TV INPUT
VOLUME
DISC SKIP
Press AMP.
Press j / i to select the desired setting.
5
AMP
Press d to display the SUBWOOFER
parameter.
PRESET/CH
2
ENTER
Press SET MENU.
“BASIC SETUP” appears in the front panel display.
SET MENU
MENU
SRCH MODE
BASIC SETUP
6
Press j / i to select the desired setting.
SUBWOOFER..YES
YES
NONE
22
If you have a subwoofer in your system.
If you do not have a subwoofer in your system.
BASIC SETUP
7
Press d to display the SPEAKERS
parameter.
11
Press ENTER to confirm your selection.
PRESET/CH
PRESET/CH
ENTER
ENTER
Press j / i to select the number of speakers
you connected.
SPEAKERS..6spk
Choices
Display
2spk
L C R
SL SB SR
3spk
L C R
SL SB SR
4spk
L C R
SL SB SR
5spk
L C R
SL SB SR
6spk
L C R
SL SB SR
CHECK:TestTone
Speakers
CHECK OK?
Front L/R
Front L/R, Center
12
CHECK OK?
YES
NO
Front L/R, Center, Surround L/R,
Surround back
13
9
Press j / i to select the desired setting.
Front L/R, Surround L/R
Front L/R, Center, Surround L/R
Press d to display SET/CANCEL.
YES
YES
To complete the setup process if the test tone
levels from each speaker were satisfactory.
To proceed to the SPEAKER LEVEL speaker
level adjustment menu to balance the level of
each speaker.
Press ENTER to confirm your selection.
PRESET/CH
PRESET/CH
ENTER
ENTER
If you selected NO in step 12, the front speaker level
adjustment display appears in the front panel display.
10
Press j / i to select the desired setting.
>SET CANCEL
SET
CANCEL
To apply the settings you chose in steps
4 through 8.
To cancel the setup without making any
changes.
23
PREPARATION
8
If you selected SET, you hear a test tone from each
speaker in turn. “CHECK:TestTone” appears in the
front panel display for a few seconds, then “CHECK:
OK?”.
BASIC SETUP
■ To balance the speaker levels
Perform the following steps after step 13 (see page 23).
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
SP
A
dB
L C R
SL
SR
The unit outputs the test tone from the selected speaker
and the left front (or left surround) speaker in turn. The
indicator of the speaker currently outputting the test tone
flashes in the front panel display.
1
Press d / u to select a speaker, then use j / i
to adjust the balance.
The control range is from +10 dB to –10 dB.
FR ----||---Adjusts the balance between the front left and right
speakers.
C ----||---Adjusts the balance between the front left and center
speakers.
SL ----||---Adjusts the balance between the front left and
surround left speakers.
SB ----||---Adjusts the balance between the surround left and
surround back speakers.
SR ----||---Adjusts the balance between the surround left and
surround right speakers.
SWFR ----||---Adjusts the balance between the front left speaker
and the subwoofer.
2
24
Press SET MENU to exit after balancing the
speakers.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby mode.
However, if the power cord is disconnected from the
AC outlet, or the power supply is cut for more than one
week, the stored data will be lost. If so, adjust the
items again.
PLAYBACK
PLAYBACK
Basic operations
4
(U.S.A. model)
Select the input source.
Use INPUT (or press one of the input selector buttons
on the remote control) to select the input you desire.
INPUT
VOLUME
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
STANDBY
/ON
PRESET/TUNING
FM/AM
XM
SEARCH MODE
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
or
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
l
STRAIGHT
SPEAKERS
A
B
PROGRAM
h
VIDEO AUX
INPUT MODE
AMP
VCR
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
L
AUDIO
R
Remote control
Front panel
1 3
7
4
6
The current input source name and input mode appear
in the front panel display for a few seconds.
VCR
1
POWER
MD/CD-R
TUNER
SLEEP
DTV/CBL
V-AUX
MULTI CH IN
AV
CD
DVD
TV VOL
TV CH
TV VOL
TV CH
VOLUME
TV MUTE
TV INPUT
STEREO
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
A SPEAKERS B
VOLUME
9
MD/CD-R
TUNER
CD
dB
L
0
+10
Selected input source
MOVIE
7
ENT.
3
EFFECT
PRESET/CH
1
DVD
R
MUTE
AMP
VCR
DTV/CBL
SP
A
6
SYSTEM
STANDBY
TV
V-AUX
VOLUME
TRANSMIT
POWER
5
Start playback or select a broadcast station
on the source component.
Refer to the operating instructions for the component.
6
Adjust the volume to the desired output level.
Press STANDBY/ON (or SYSTEM POWER on
the remote control) to turn on the power.
SYSTEM
Input mode
POWER
STANDBY
/ON
VOLUME
or
Front panel
2
3
Remote control
or
Turn on the video monitor connected to this
unit.
Front panel
VOLUME
Remote control
Press SPEAKERS A or B (or press AMP to
select the AMP mode, then press SPEAKERS
A or B on the remote control).
Each press turns the respective speakers on or off.
SPEAKERS
A
B
or
Front panel
AMP
A SPEAKERS B
9
0
Remote control
25
BASIC
OPERATION
4
3
CODE SET
POWER
PLAYBACK
■ To adjust the tone
7
Select a sound field program if desired.
Press PROGRAM l / h repeatedly (or press AMP
to select the AMP mode, then press one of the sound
field program buttons on the remote control) to select
a sound field program. (See page 49 for details about
sound field programs.)
You can adjust the tonal quality
TONE CONTROL
of your front left and right
speakers or headphones (when
connected).
Press TONE CONTROL on the
front panel repeatedly to select
TREBLE or BASS, then press
BASS/TREBLE –/+ repeatedly
to increase or decrease.
• Select TREBLE to adjust the
high frequency response.
• Select BASS to adjust the low frequency response.
BASS/TREBLE
l
h
PROGRAM
Front panel
or
y
AMP
STEREO
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
A SPEAKERS B
9
0
NIGHT
10
STRAIGHT
ENT.
EFFECT
Remote control
■ To listen with headphones
(“SILENT CINEMA”)
Speaker and headphone adjustments are stored independently.
Notes
• If you increase or decrease the high-frequency or low-frequency
sound to an extreme level, the tonal quality of the surround
speakers may not match that of the front left and right speakers.
• TONE CONTROL is not effective with the Direct Stereo
program (page 30) or MULTI CH INPUT.
• When TC BYPASS is set to AUTO (page 58), and BASS and
TREBLE are set to 0 dB, audio output automatically bypasses
this unit’s tone control circuitry.
“SILENT CINEMA” allows you to enjoy multi-channel
music or movie sound, including Dolby Digital and DTS
surround, through ordinary headphones. “SILENT
CINEMA” activates automatically whenever you connect
headphones to the PHONES jack while listening to
CINEMA DSP or HiFi DSP sound field programs. When
activated, the “SILENT CINEMA” indicator lights up in
the front panel display.
■ To mute the sound
Notes
y
• This unit will not be set to “SILENT CINEMA” when MULTI
CH INPUT is selected as the input source.
• “SILENT CINEMA” is not effective when the Direct Stereo or
2ch Stereo program is selected, or in STRAIGHT mode.
26
Press MUTE on the remote control.
The MUTE indicator flashes in the
front panel display.
To resume the audio output, press
MUTE again (or press VOLUME –/+).
The MUTE indicator disappears from
the display.
You can adjust the muting level (see page 58).
MUTE
PLAYBACK
■ Selecting MULTI CH INPUT
Press MULTI CH INPUT (or MULTI CH IN on the
remote control) so that “MULTI CH INPUT” appears in
the front panel display.
Selecting sound field programs
■ Front panel operation
(U.S.A. model)
MULTI CH
INPUT
MULTI CH IN
or
VOLUME
STANDBY
/ON
Front panel
Remote control
PRESET/TUNING
A/B/C/D/E
FM/AM
XM
SEARCH MODE
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
L
AUDIO
R
MULTI CH INPUT
PROGRAM
Note
When “MULTI CH INPUT” is shown in the front panel display,
no other source can be played. To select another input source with
INPUT (or one of the input selector buttons), press MULTI CH
INPUT (or MULTI CH IN on the remote control) to turn off
“MULTI CH INPUT” in the front panel display.
Press PROGRAM l / h repeatedly to select the
desired program.
The name of the selected program appears in the front
panel display.
You can combine a video image from a video source with
sound from an audio source. For example, you can enjoy
listening to classical music while viewing beautiful
scenery from the video source on the video monitor.
Use the input selector buttons on the remote
control to select a video source, then select an
audio source.
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
l
VCR
V-AUX
PROGRAM
DTV/CBL
h
DVD
MD/CD-R
BASIC
OPERATION
■ Playing video sources in the
background
TUNER
CD
VOLUME
SP
A
TV Sports
dB
L
R
Program name
Audio sources
VCR
AMP
Video sources
Note
If you want to enjoy audio from the MULTI CH INPUT jacks
together with a video source, first select the video source, then
press MULTI CH INPUT (or MULTI CH IN on the remote
control).
27
PLAYBACK
■ Remote control operation
CODE SET
TRANSMIT
TV VOL
TV CH
■ Enjoying multi-channel software
If you connected a surround back speaker, use this feature
to enjoy 6.1-channel playback for multi-channel sources
using the Dolby Pro Logic IIx, Dolby Digital EX or
DTS-ES decoders.
VOLUME
SYSTEM
POWER
AMP
POWER
STANDBY
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
TV INPUT
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
MUTE
AMP
VCR
TV MUTE
STEREO
A SPEAKERS B
9
0
10
MOVIE
Sound field
program
buttons
ENT.
EFFECT
TV VOL
TV MUTE
TV CH
VOLUME
LEVEL
PRESET/CH
SET MENU
TITLE
MENU
BAND
SRCH MODE
TV INPUT
Press AMP on the remote control to select the
AMP mode, then press EXTD SUR. to switch
between 5.1 and 6.1-channel playback.
ENTER
EXTD SUR.
AMP
7
Press AMP to select the AMP mode, then press
one of the sound field program buttons
repeatedly to select the desired program.
The name of the selected program appears in the front
panel display.
To select a decoder, press j / i repeatedly while
PLIIxMusic (etc.) is displayed.
PRESET/CH
STEREO
AMP
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
A SPEAKERS B
9
0
10
ENTER
A-E/CAT.
ENT.
EFFECT
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
SP
A
TV Sports
A-E/CAT.
dB
L
R
Program name
y
Feel free to choose a sound field program based on your listening
preference, and not purely on the name of the program itself.
Notes
• When you select an input source, this unit automatically selects
the last sound field program used with that source.
• Sound field programs cannot be selected when MULTI CH
INPUT is selected.
• Sampling frequencies higher than 48 kHz (except for DTS 96/
24 signals) will be sampled down to 48 kHz, then sound field
programs will be applied.
Auto (AUTO)
When a signal (flag) that can be recognized by the unit is
input, the unit selects the optimum decoder for playing
back the signal in 6.1 channels.
If the unit cannot recognize the flag or no flag is present in
the input signal, it cannot automatically be played in 6.1
channels.
Decoders (select with j / i)
You can select from the following decoders depending on
the format of the software you are playing.
PLIIxMusic
For playing back Dolby Digital or DTS signals in 6.1
channels using the Pro Logic IIx music decoder.
EX/ES
For playing back Dolby Digital signals in 6.1 channels
using the Dolby Digital EX decoder.
DTS signals are played back in 6.1 channels using the
DTS-ES decoder.
EX
For playing back Dolby Digital or DTS signals in 6.1
channels using the Dolby Digital EX decoder.
Off (OFF)
Decoders are not used to create 6.1 channels.
28
PLAYBACK
When you select the SUR. STANDARD program:
Notes
• Some 6.1-channel compatible discs do not have a signal (flag)
which this unit can automatically detect. When playing these
kinds of discs with 6.1-channel, select a decoder manually
(PLIIx Music, EX/ES or EX).
• 6.1-channel playback is not possible even if EXTD SUR. is
pressed in the following cases:
– When “SUR. LR” (see page 56) or “SUR. B” (see page 56) is
set to NONE.
– When the source connected to the MULTI CH INPUT jack is
being played.
– When the source being played does not contain surround left
and right channel signals.
– When a Dolby Digital KARAOKE source is being played.
– When “2ch Stereo” or “Direct Stereo” is selected.
• When the power of this unit is turned off, this setting will be
reset to AUTO.
• The Pro Logic IIx decoder is not available when “SUR. B” is set
to NONE (see page 56).
■ Enjoying 2-channel software in surround
PRO LOGIC
Dolby Pro Logic processing for any sources.
PLII Movie
Dolby Pro Logic II processing for movie software.
PLII Music
Dolby Pro Logic II processing for music software.
PLII Game
Dolby Pro Logic II processing for game software.
PLIIx Movie
Dolby Pro Logic IIx processing for movie software.
PLIIx Music
Dolby Pro Logic IIx processing for music software.
PLIIx Game
Dolby Pro Logic IIx processing for game software.
Neo:6 Cinema
DTS processing for movie software.
Press AMP to select the AMP mode, then press
STANDARD on the remote control to switch
between the SUR. STANDARD and SUR.
ENHANCED programs.
Neo:6 Music
DTS processing for music software.
AMP
STANDARD
5
Or press MOVIE to select the MOVIE THEATER
program.
MOVIE
When you select the SUR. ENHANCED or MOVIE
THEATER program:
PRO LOGIC
Dolby Pro Logic processing for any sources.
PLII Movie
Dolby Pro Logic II processing for movie software.
PLIIx Movie
Dolby Pro Logic IIx processing for movie software.
4
Neo:6 Cinema
DTS processing for movie software.
Press SELECT on the remote control to select
the decoder.
SELECT
y
You can also select a decoder by pressing j / i on the remote
control when the decoder type is displayed in the front panel
display.
6
Note
You can select from the following modes depending on the
type of software you are playing and your personal
preference.
The Pro Logic IIx decoder is not available when “SUR. B” is set
to NONE (see page 56).
29
BASIC
OPERATION
Signals input from 2-channel sources can also be played
back on multiple channels.
PLAYBACK
■ Listening to high fidelity stereo sound
(Direct Stereo)
Direct Stereo allows you to bypass this unit’s decoders and
DSP processors to enjoy pure high fidelity sound from 2channel PCM and analog sources.
Press PROGRAM l / h repeatedly (or press
AMP to select the AMP mode, then press DIRECT
ST. on the remote control) to select “DIRECT
STEREO”.
l
PROGRAM
or
Front panel
The night listening modes are designed to improve
listenability at lower volumes or at night. Choose either
NIGHT:CINEMA or NIGHT:MUSIC depending on the
type of material you are playing.
Press AMP on the remote control to select the
AMP mode, then press NIGHT repeatedly to
select cinema or music.
When night listening is selected, the NIGHT indicator in
the front panel display lights up.
DIRECT ST.
AMP
h
■ Night listening modes
NIGHT
AMP
8
10
Remote control
DIRECT STEREO
Notes
• To avoid unexpected noise, do not play DTS-encoded CDs in
this mode.
• When multi-channel signals (Dolby Digital and DTS) are input,
this unit automatically switches to the corresponding analog
input. (When DTS is selected as an input mode, no sound will
be heard.)
• No sound will be output from the subwoofer.
• TONE CONTROL (page 26) and SET MENU (page 54)
settings are not effective.
• The front panel display automatically dims.
• If you press AMP on the remote control to select the AMP
mode, then press DIRECT ST., the unit automatically enters
Direct Stereo mode and you cannot toggle between the unit’s
other sound field programs.
• Select NIGHT:CINEMA when watching films to
reduce the dynamic range of film soundtracks and
make dialog easier to hear at lower volumes.
• Select NIGHT:MUSIC when listening to music sources
to preserve ease-of-listening for all sounds.
• Select OFF if you do not want to use this function.
Press j / i to adjust the effect level while
NIGHT:CINEMA or NIGHT:MUSIC is displayed.
This adjusts the level of compression.
PRESET/CH
ENTER
A-E/CAT.
A-E/CAT.
Remote control
Effect.Lvl:MID
• Select MIN for minimum compression.
• Select MID for standard compression.
• Select MAX for maximum compression.
y
NIGHT:CINEMA and NIGHT:MUSIC adjustments are stored
independently.
Notes
• You cannot use the night listening modes with the Direct Stereo
program or MULTI CH INPUT (even though the NIGHT
indicator lights up when Direct Stereo is selected).
• The night listening modes may vary in effectiveness depending
on the input source and surround sound settings you use.
30
PLAYBACK
■ Downmixing to 2 channels
You can enjoy 2-channel stereo playback even from multichannel sources.
Press PROGRAM l / h repeatedly (or press
AMP to select the AMP mode, then press
STEREO on the remote control) to select 2ch
Stereo.
l
PROGRAM
h
AMP
or
Selecting input modes
This unit comes with a variety of input jacks. Do the
following to select the type of input signals you want to
use.
1
Rotate INPUT to select the input source.
STEREO
INPUT
1
Front panel
Remote control
Front panel
2ch Stereo
2
y
Press INPUT MODE to select an input mode.
In most cases, use AUTO.
You can use a subwoofer with this program when SWFR or
BOTH is selected in “BASS OUT”.
INPUT MODE
BASIC
OPERATION
■ Listening to unprocessed input signals
In STRAIGHT mode, two channel stereo sources are
output from only the front left and right speakers. Multichannel sources are decoded straight into the appropriate
channels without any additional effect processing.
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
SP
A
Press STRAIGHT (or press AMP on the remote
control to select the AMP mode, then press
STRAIGHT) to select STRAIGHT.
AMP
STRAIGHT
or
EFFECT
Input source
STRAIGHT
AUTO
ENT.
EFFECT
Front panel
dB
L
Remote control
DTS
STRAIGHT
ANALOG
Press STRAIGHT (EFFECT) again so that “STRAIGHT”
disappears from the display when you want to turn the
sound effect back on.
R
Input mode
Automatically selects input signals in
the following order:
1) Digital signals*
2) Analog signals
Selects only digital signals encoded in
DTS. If no DTS signals are input, no
sound is output.
Selects only analog signals. If no
analog signals are input, no sound is
output.
* If this unit detects a Dolby Digital or DTS signal, the
decoder automatically switches to the appropriate
decoder.
■ Virtual CINEMA DSP
y
Virtual CINEMA DSP allows you to enjoy the CINEMA
DSP programs without surround speakers. It creates
virtual speakers to reproduce the natural sound field.
If you set “SUR. LR” to NONE (see page 56), Virtual
CINEMA DSP activates automatically whenever you
select a CINEMA DSP sound field program.
You can adjust the default input mode of this unit (see page 59).
Note
Virtual CINEMA DSP will not activate, even when “SUR. LR” is
set to NONE (see page 56) in the following cases:
– When MULTI CH INPUT is selected as the input source.
– When headphones are connected to the PHONES jack.
31
PLAYBACK
Notes
3
• When playing a DTS-CD/LD, be sure to set INPUT MODE to
DTS.
• If the digital output data of the player has been processed in any
way, you may not be able to perform DTS decoding even if you
make a digital connection between this unit and the player
depending on the player.
Press u / d to display the following
information about the input signal.
PRESET/CH
ENTER
A-E/CAT.
A-E/CAT.
■ Displaying information about the input
source
You can display the type, format and sampling frequency
of the current input signal.
(Format)
1
in
Select the input source.
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
AMP
VCR
fs
rate
2
Press AMP to select the AMP mode, then
press STRAIGHT so that “STRAIGHT”
appears in the display.
STRAIGHT
AMP
then
ENT.
EFFECT
STRAIGHT
32
flg
Signal format display. When the unit
cannot detect a digital signal it
automatically switches to analog input.
Number of source channels in the input
signal. For example, a multi-channel
soundtrack with 3 front channels, 2
surround channels and LFE, is
displayed as “3/2/LFE”.
Sampling frequency. When the unit is
unable to detect the sampling
frequency “Unknown” appears.
Bit rate. When the unit is unable to
detect the bit rate “Unknown” appears.
Flag data encoded with DTS or Dolby
Digital signals that cue this unit to
automatically switch decoders.
FM/AM TUNING
FM/AM TUNING
Automatic and manual tuning
3
There are 2 tuning methods; automatic and manual.
Automatic tuning is effective when station signals are
strong and there is no interference.
Press TUNING MODE (AUTO/MAN’L MONO)
so that the AUTO indicator lights up in the
front panel display.
TUNING MODE
AUTO
DISPLAY
■ Automatic tuning
Lights up
AUTO/MAN'L MONO
(U.S.A. model)
If a colon (:) appears in the front panel display, tuning
is not possible. Press PRESET/TUNING (EDIT) to
turn the colon (:) off.
VOLUME
STANDBY
/ON
PRESET/TUNING
FM/AM
XM
SEARCH MODE
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
PRESET/TUNING
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
SEARCH MODE
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EDIT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
4
AUDIO
R
1 3
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
BASIC
OPERATION
3 2
L
TUNER
AUTO TUNED
SP
A
1
Rotate INPUT to select TUNER as the input
source.
4
INPUT
Press PRESET/TUNING/CH l / h once to
begin automatic tuning.
Press h to tune into a higher frequency, or press l
to tune into a lower frequency.
l PRESET/TUNING/CH h
Front panel
LEVEL
2
Press FM/AM to select the reception band.
“FM” or “AM” appears in the front panel display.
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
AUTO TUNED
SP
A
FM/AM
XM
Front panel
FM
or
AM
When tuned into a station, the TUNED indicator
lights up and the frequency of the received station is
shown in the front panel display.
33
FM/AM TUNING
■ Manual tuning
If the signal from the station you want to select is weak,
tune into it manually. Manually tuning into an FM station
will automatically switch the tuner to monaural reception
to increase the signal quality.
1
Select TUNER and the reception band
following steps 1 and 2 as described in
“Automatic tuning”.
2
Press TUNING MODE (AUTO/MAN’L MONO)
so that the AUTO indicator disappears from
the front panel display.
Presetting stations
■ Automatically presetting FM stations
You can use the automatic preset tuning feature to store
FM stations. This function enables this unit to
automatically tune into FM stations with strong signals,
and to store up to 40 (8 stations in 5 groups, A1 through
E8) of those stations in order. You can then recall any
preset station easily by selecting the preset station number.
(U.S.A. model)
VOLUME
STANDBY
/ON
PRESET/TUNING
FM/AM
XM
SEARCH MODE
A/B/C/D/E
AUTO
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
TUNING MODE
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
DISPLAY
TONE CONTROL
Disappears
AUTO/MAN'L MONO
If a colon (:) appears in the front panel display, tuning
is not possible. Press PRESET/TUNING (EDIT) to
turn the colon (:) off.
PRESET/TUNING
BASS/TREBLE
VIDEO
SILENT CINEMA
1
1
L
AUDIO
R
3 2
Press FM/AM to select the FM band.
SEARCH MODE
FM/AM
EDIT
FM
XM
Front panel
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
AUTO
SP
A
2
3
Press PRESET/TUNING/CH l / h to tune
into the desired station manually.
Hold down the button to
continue searching.
l PRESET/TUNING/CH h
Press TUNING MODE (AUTO/MAN’L MONO)
so that the AUTO indicator lights up in the
front panel display.
AUTO
TUNING MODE
DISPLAY
Lights up
AUTO/MAN'L MONO
LEVEL
If a colon (:) appears in the front panel display, tuning
is not possible. Press PRESET/TUNING (EDIT) to
turn the colon (:) off.
PRESET/TUNING
SEARCH MODE
EDIT
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
AUTO
SP
A
34
TUNER
FM/AM TUNING
■ Manually presetting stations
3
Press and hold MEMORY (MAN’L/AUTO FM)
for more than 3 seconds.
The preset number, the MEMORY and AUTO
indicators flash. After about 5 seconds, automatic
presetting starts from the frequency currently
displayed and proceeds toward the higher
frequencies.
You can also store up to 40 stations (8 stations x 5 groups)
manually.
(U.S.A. model)
VOLUME
STANDBY
/ON
PRESET/TUNING
SEARCH MODE
FM/AM
XM
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
MEMORY
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
L
AUDIO
R
MAN'L/AUTO FM
34
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
AUTO TUNED
2,5
CD
MEMORY
VOLUME
SP
A
dB
L
R
1
Tune into a station.
See page 33 for tuning instructions.
When automatic preset tuning is completed, the front
panel display shows the frequency of the last preset
station.
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED
VOLUME
SP
A
dB
L
R
• Any stored station data existing under a preset number is
cleared when you store a new station under that preset number.
• If the number of received stations does not reach 40 (E8),
automatic preset tuning has automatically stopped after
searching all stations.
• Only FM stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station you
want to store is weak in signal strength, tune into it manually
and store it by following the procedure in “Manually presetting
stations”.
When tuned into a station, the front panel display
shows the frequency of the station received.
2
Press MEMORY (MAN’L/AUTO FM).
The MEMORY indicator flashes for about 5 seconds.
MEMORY
MEMORY
MAN'L/AUTO FM
Flashes
Automatic preset tuning options:
You can select the preset number from which this unit will
store FM stations and/or begin tuning toward lower
frequencies.
After pressing MEMORY in step 3:
1 Press A/B/C/D/E (NEXT), then PRESET/TUNING/
CH l / h to select the preset number under which the
first station will be stored. Automatic preset tuning will
stop when stations have all been stored up to E8.
2 Press PRESET/TUNING (EDIT) to turn off the colon
(:) and then press PRESET/TUNING/CH l to begin
tuning toward the lower frequencies.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the preset stations may be cleared. If
so, store the stations again by using the presetting
station methods.
3
Press A/B/C/D/E (NEXT) repeatedly to select
a preset station group (A to E) while the
MEMORY indicator is flashing.
The group letter appears. Check that the colon (:)
appears in the front panel display.
A/B/C/D/E
CATEGORY
NEXT
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
CD
MEMORY
VOLUME
SP
A
dB
L
R
Preset group
35
BASIC
OPERATION
Notes
FM/AM TUNING
4
Press PRESET/TUNING/CH l / h to select a
preset station number (1 to 8) while the
MEMORY indicator is flashing.
Press h to select a higher preset station number.
Press l to select a lower preset station number.
Selecting preset stations
You can tune any desired station simply by selecting the
preset station number under which it was stored.
1
2
(U.S.A. model)
l PRESET/TUNING/CH h
VOLUME
LEVEL
STANDBY
/ON
PRESET/TUNING
A/B/C/D/E
FM/AM
XM
SEARCH MODE
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
CD
MEMORY
TONE CONTROL
VOLUME
SP
A
BASS/TREBLE
VIDEO
SILENT CINEMA
A SPEAKERS B
9
NIGHT
0
ENT.
EFFECT
TITLE
Press MEMORY (MAN’L/AUTO FM) on the
front panel while the MEMORY indicator is
flashing.
The station band and
MEMORY
frequency appear in the front
panel display with the preset
group and number you have
selected.
MAN'L/AUTO FM
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
CD
MEMORY
VOLUME
SP
A
dB
L
R
SET MENU
1
MENU
SRCH MODE
BAND
V-AUX
R
STRAIGHT
10
PRESET/CH
LEVEL
VCR
AUDIO
R
Preset number
5
L
dB
L
ENTER
A-E/CAT.
RETURN
A-E/CAT.
DISPLAY
MEMORY
2
REC
AUDIO
y
When performing this operation with the remote control, first
press TUNER to set the remote to tuner mode.
1
Press A/B/C/D/E (NEXT) (or A-E/CAT. j / i on
the remote control) to select the preset
station group.
The preset group letter appears in the front panel
display and changes each time you press the button.
Shows the displayed station has been stored as C3.
PRESET/CH
6
Repeat steps 1 to 5 to store other stations.
A/B/C/D/E
or
CATEGORY
NEXT
Notes
• Any stored station data existing under a preset number is
cleared when you store a new station under that preset number.
• The reception mode (stereo or monaural) is stored along with
the station frequency.
36
Front panel
ENTER
A-E/CAT.
A-E/CAT.
Remote control
FM/AM TUNING
2
Press PRESET/TUNING/CH l / h (or
PRESET/CH u / d on the remote control) to
select a preset station number (1 to 8).
The preset group and number appear in the front
panel display along with the station band, frequency
and the TUNED indicator lights up.
Exchanging preset stations
You can exchange the assignment of two preset stations
with each other. The example below describes the
procedure for exchanging preset station “E1” with “A5”.
(U.S.A. model)
PRESET/CH
VOLUME
STANDBY
/ON
l PRESET/TUNING/CH h
or
PRESET/TUNING
ENTER
FM/AM
XM
SEARCH MODE
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
LEVEL
AUTO/MAN'L MONO
INPUT
A-E/CAT.
A-E/CAT.
PHONES
SPEAKERS
A
B
l
STRAIGHT
h
PROGRAM
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
Front panel
AUDIO
R
Remote control
2,4
VCR
L
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
SP
A
CD
1,3
1,3
Select preset station “E1”.
See “Selecting preset stations”.
2
Press and hold PRESET/TUNING (EDIT) for
more than 3 seconds.
“E1” and the MEMORY indicator flash in the front
panel display.
PRESET/TUNING
SEARCH MODE
EDIT
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
CD
MEMORY
SP
A
37
BASIC
OPERATION
1
FM/AM TUNING
3
Select preset station “A5” using A/B/C/D/E
and PRESET/TUNING/CH l / h.
“A5” and the MEMORY indicator flash in the front
panel display.
l PRESET/TUNING/CH h
A/B/C/D/E
CATEGORY
LEVEL
NEXT
VCR
V-AUX
DTV/CBL
MD/CD-R
DVD
TUNER
TUNED
CD
MEMORY
SP
A
4
Press PRESET/TUNING (EDIT) again.
The stations stored at the two preset assignments are
exchanged.
PRESET/TUNING
SEARCH MODE
EDIT
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED
SP
A
38
CD
XM SATELLITE RADIO TUNING
XM SATELLITE RADIO TUNING
What is XM Satellite Radio?
XM Satellite Radio is the satellite radio service with
millions of listeners across the U.S., broadcasting live
daily. XM’s channel lineup includes more than 130 digital
channels of choice from coast to coast: 68 commercialfree music channels, featuring hip hop to opera, classical
to country, bluegrass to blues; 33 channels of premier
sports, talk, comedy, children’s and entertainment
programming; and more than 20 channels of the traffic
and weather information for major metropolitan areas
nationwide.
XM Satellite Radio functions
This section describes the functions of each control used
for XM Satellite Radio tuning.
■ Front panel functions
Note
The following controls are only available when the unit is in the TUNER
mode and the XM Connect and Play digital antenna accessory is connected
to the XM jack on the rear of this unit. (For details, see “XM Satellite
Radio connections”.)
PRESET/TUNING
Notes
• The XM Satellite Radio service is only available in the 48
contiguous United States (not available in Alaska and Hawaii).
• XM Connect and Play digital antenna accessory and monthly
subscription are sold separately. For details, see the XM
Satellite Radio website at “http://www.xmradio.com”.
XM Satellite Radio connections
■ Connecting the XM Connect and Play
digital antenna accessory
Connect the XM Connect and Play digital antenna accessory
(sold separately) to the XM jack on the rear of this unit. (For
details, see the operating instructions provided with the XM
Connect and Play digital antenna accessory.)
XM
XM jack
Notes
• For information on obtaining the XM Connect and Play digital antenna
accessory, see the website at “http://www.xmradio.com” or visit your local
retailer that sells XM Ready products.
• To ensure optimal reception of XM’s satellite signal, the XM Connect and Play
digital antenna accessory should be placed at or near a southerly facing window
with nothing obstructing its path to the sky. You can mount it indoors or
outdoors.
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
NEXT
1
2
TUNING MODE
DISPLAY
DISPLAY
CATEGORY
EDIT
3
4
AUTO/MAN'L MONO
5 6
1 SEARCH MODE
Switches between the All Channel Search, Category Search, and Preset Search
modes. (For details, see “XM Satellite Radio search modes” on page 42.)
2 XM
Switches the reception band between AM, FM and XM.
3 CATEGORY
(All Channel Search mode)
Changes the channel category to next one (while staying
in the All Channel Search mode).
(Category Search mode)
Changes the channel category to next one.
(Preset Search mode)
Switches between five preset groups (A to E).
4 PRESET/TUNING/CH l / h
(All Channel Search mode)
Searches a radio channel within all channels. Press and
hold for quick search.
(Category Search mode)
Searches a radio channel within the selected category.
Press and hold for quick search.
(Preset Search mode)
Changes the preset number (1 to 8).
5 MEMORY
Switches the unit to the preset memory mode.
6 DISPLAY
Switches XM information such as channel number/name,
category, or artist name/song title displayed in the front panel
display. (For details, see “Switching XM information” on
page 42.)
39
BASIC
OPERATION
Because XM Satellite Radio is a subscription service, you
will need to set up an account and activate service with
XM using your XM Satellite Radio ID number. To check
your ID number, follow “Activating XM Satellite Radio”
on page 40. For further information on XM Satellite Radio
services, see the XM Satellite Radio website at
“http://www.xmradio.com”.
A/B/C/D/E
FM/AM
XM
SEARCH MODE
XM SATELLITE RADIO TUNING
■ Remote control functions
Activating XM Satellite Radio
Note
The following controls are only available when the unit is in the
TUNER mode. To switch to the TUNER mode, press TUNER to
select TUNER as the input source.
TV VOL
TV CH
VOLUME
TV MUTE
TV INPUT
STEREO
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
MUTE
1
A SPEAKERS B
9
0
MOVIE
10
ENT.
EFFECT
2
3
4
PRESET/CH
LEVEL
To sign up for an account with the XM Satellite Radio
service, an XM Satellite Radio ID number is required.
Follow the procedure below to check your ID number, and
then access the website at “http://activate.xmradio.com”
or call “1-800-XM-RADIO (1-800-967-2346)” with a
major credit card for signing up.
SET MENU
TITLE
MENU
BAND
SRCH MODE
VOLUME
5
STANDBY
/ON
6
PRESET/TUNING
FM/AM
XM
SEARCH MODE
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
ENTER
STRAIGHT
SPEAKERS
A
B
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
A-E/CAT.
A-E/CAT.
RETURN
DISPLAY
MEMORY
7
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
L
AUDIO
R
REC
AUDIO
DISC SKIP
FREQ/RDS
MODE
PTY SEEK START
EON
1 Numeric buttons
(All Channel Search or Category Search mode)
Use 1 to 9 and 0 to enter a channel number directly.
(Preset Search mode)
Use 1 to 8 to enter a preset channel number directly.
2
1
3
Rotate INPUT (or press TUNER on the remote
control) to select TUNER as the input source.
INPUT
TUNER
2 BAND
Switches the reception band between the currently
selected band (AM or FM) and XM.
3 Cursor buttons u / d / j / i
(All Channel Search mode)
Press A-E/CAT. j / i to change the channel category.
Press PRESET/CH u / d to search a radio channel
within all channels. Press and hold for quick search.
(Category Search mode)
Press A-E/CAT. j / i to change the channel category.
Press PRESET/CH u / d to search a radio channel within
the selected category. Press and hold for quick search.
(Preset Search mode)
Press A-E/CAT. j / i to change the preset group (A to E).
Press PRESET/CH u / d to change the preset number (1 to 8).
4 MEMORY
Switches the unit to the preset memory mode.
5 ENT.
Confirms an entered channel number during the Direct
Number Access mode (see pages 44).
6 SRCH MODE
Switches between the All Channel Search, Category
Search, and Preset Search modes. (For details, see “XM
Satellite Radio search modes” on page 42.)
7 DISPLAY
Switches XM information such as channel number/name,
category, or artist name/song title displayed in the front panel
display. (For details, see “Switching XM information” on
page 42.)
40
1
or
Front panel
2
Remote control
Press XM (or BAND on the remote control) to
select “XM” as the reception band.
FM/AM
LEVEL
or
XM
TITLE
BAND
Front panel
VCR
V-AUX
Remote control
DTV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED STEREO
SP
A
XM
XM RADIO
Lights
If “CHECK ANTENNA” appears in the front panel
display, the XM Connect and Play digital antenna
accessory may not be connected to the XM jack on
the rear of this unit properly. See “XM Satellite Radio
connections” on page 39 and check the connection.
XM SATELLITE RADIO TUNING
3
Press PRESET/TUNING/CH l / h (or
PRESET/CH u / d on the remote control) to
select channel “0”.
Basic XM Satellite Radio
operations
■ Selecting the XM Satellite Radio mode
PRESET/CH
l PRESET/TUNING/CH h
or
ENTER
LEVEL
A-E/CAT.
A-E/CAT.
PRESET/TUNING
A/B/C/D/E
FM/AM
XM
SEARCH MODE
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
Front panel
Remote control
STRAIGHT
l
PROGRAM
h
INPUT MODE
TONE CONTROL
MULTI CH
INPUT
BASS/TREBLE
Note
You cannot select channel “0” if the “All Channel Search mode”
(see page 42) is not selected.
4
1
Rotate INPUT (or press TUNER on the remote
control) to select TUNER as the input source.
BASIC
OPERATION
Check the XM Satellite Radio ID number
displayed in the front panel display and write
it down.
1
2
INPUT
ID:_____________________________________
TUNER
or
Front panel
2
Remote control
Press XM (or BAND on the remote control) to
select “XM” as the reception band.
Information (such as channel number/name, category,
or artist name/song title) for the channel currently
selected appears in the front panel display and the
XM indicator lights up.
LEVEL
FM/AM
or
XM
TITLE
BAND
Remote control
Front panel
VCR
V-AUX
DTV/CBL
SP
A
DVD
MD/CD-R
TUNER
XM
[001] Preview
CD
Lights
y
• Selecting the “XM” band automatically recalls the channel
previously selected.
• You can change the kind of XM information by pressing
DISPLAY repeatedly. (For details, see “Switching XM
information” on page 42.)
Note
XM Satellite Radio signals cannot be output from the AUDIO
OUT (REC) jacks.
41
XM SATELLITE RADIO TUNING
■ Switching XM information
You can display XM information (such as channel
number/name, category, or artist name/song title) for the
channel currently selected in the front panel display.
Press DISPLAY on the unit (or remote control
during the TUNER mode) repeatedly to toggle
between the following XM information display
modes.
XM Satellite Radio search modes
You can search for the channel you want to listen to using
one of three search modes. You can also enter the number
directly to select the desired channel. (For details, see
“Direct Number Access mode” on page 44.)
■ All Channel Search mode
TUNING MODE
(U.S.A. model)
Channel name/number
DISPLAY
AUTO/MAN'L MONO
Front panel
Channel category
or
PRESET/TUNING
A/B/C/D/E
FM/AM
XM
SEARCH MODE
DISPLAY
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
NEXT
AUTO/MAN'L MONO
INPUT
Artist name/Song title
Remote control
l PRESET/TUNING/CH h
CATEGORY
EDIT
STRAIGHT
l
PROGRAM
h
INPUT MODE
TONE CONTROL
MULTI CH
INPUT
BASS/TREBLE
When the channel number/name is displayed:
VCR
V-AUX
DTV/CBL
DVD
SP
A
MD/CD-R
TUNER
CD
XM
When the channel category is displayed:
VCR
V-AUX
DTV/CBL
DVD
SP
A
MD/CD-R
TUNER
V-AUX
Carry out “Selecting the XM Satellite Radio
mode” on page 41.
2
Press SEARCH MODE (or SRCH MODE on
the remote control) repeatedly to select “ALL
CH SEARCH”.
CD
When the artist name/song title is displayed:
SP
A
1
XM
<CAT>Rock
VCR
3
2
[040] Deep Tra
DTV/CBL
DVD
MD/CD-R
TUNER
CD
XM
Coldplay / Clo
SET MENU
PRESET/TUNING
MENU
or
SEARCH MODE
SRCH MODE
EDIT
Front panel
Remote control
y
• The front panel display can indicate up to 14 alphanumeric
characters at once. If the information contains more than 14
characters, the information scrolls from right to left.
• If the information contains a character that cannot be
recognized by the unit, the character will be displayed with an
underbar “_”.
Note
If a status message or an error message appears in the display, see
“Status and error messages” on page 47.
42
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED STEREO
SP
A
XM
ALL CH SEARCH
CD
XM SATELLITE RADIO TUNING
■ Category Search mode
3
To change the channel category, press
CATEGORY (or A-E/CAT. j / i on the remote
control) repeatedly.
PRESET/TUNING
A/B/C/D/E
FM/AM
XM
SEARCH MODE
PRESET/CH
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
STRAIGHT
A/B/C/D/E
PROGRAM
h
TONE CONTROL
A-E/CAT.
Front panel
BASS/TREBLE
A-E/CAT.
Remote control
To search a channel within all channels,
press PRESET/TUNING/CH l / h (or
PRESET/CH u / d on the remote control)
repeatedly.
PRESET/CH
or
1
Carry out “Selecting the XM Satellite Radio
mode” on page 41.
2
Press SEARCH MODE (or SRCH MODE on
the remote control) repeatedly to select “CAT
SEARCH”.
ENTER
A-E/CAT.
3
2
l PRESET/TUNING/CH h
A-E/CAT.
BASIC
OPERATION
SET MENU
PRESET/TUNING
or
SEARCH MODE
MENU
SRCH MODE
EDIT
Front panel
MULTI CH
INPUT
ENTER
NEXT
LEVEL
l
INPUT MODE
or
CATEGORY
Remote control
Front panel
Remote control
y
You can search a channel with the quick search by pressing and
holding PRESET/TUNING/CH l / h (or PRESET/CH u / d
on the remote control).
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED STEREO
SP
A
XM
CAT SEARCH
3
To change the channel category, press
CATEGORY (or A-E/CAT. j / i on the remote
control) repeatedly.
PRESET/CH
A/B/C/D/E
or
CATEGORY
ENTER
NEXT
A-E/CAT.
Front panel
A-E/CAT.
Remote control
To search a channel within the selected
channel category, press PRESET/TUNING/CH
l / h (or PRESET/CH u / d on the remote
control) repeatedly.
PRESET/CH
l PRESET/TUNING/CH h
or
LEVEL
Front panel
ENTER
A-E/CAT.
A-E/CAT.
Remote control
y
You can search a channel with the quick search by pressing and
holding PRESET/TUNING/CH l / h (or PRESET/CH u / d
on the remote control).
43
XM SATELLITE RADIO TUNING
■ Preset Search mode
■ Direct Number Access mode
Prior to selecting a preset channel in the Preset Search
mode, you should preset XM Satellite Radio channels. For
details, see “Setting XM Satellite Radio preset channels”
on page 45. All preset channels (A1 to E8) recalls “001
Preview” by the factory setting.
TV VOL
TV CH
TV MUTE
TV INPUT
STEREO
MUSIC
VOLUME
MUTE
3
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
A SPEAKERS B
9
0
10
4
2
ENT.
EFFECT
PRESET/CH
LEVEL
SET MENU
TITLE
MENU
SRCH MODE
BAND
PRESET/TUNING
A/B/C/D/E
FM/AM
XM
SEARCH MODE
l PRESET/TUNING/CH h
MEMORY
ENTER
TUNING MODE
A-E/CAT.
DISPLAY
CATEGORY
NEXT
EDIT
LEVEL
MAN'L/AUTO FM
A-E/CAT.
RETURN
AUTO/MAN'L MONO
DISPLAY
MEMORY
INPUT
REC
AUDIO
STRAIGHT
l
PROGRAM
h
INPUT MODE
TONE CONTROL
BASS/TREBLE
2
1
2
DISC SKIP
MULTI CH
INPUT
3
Carry out “Selecting the XM Satellite Radio
mode” on page 41.
Press SEARCH MODE (or SRCH MODE on
the remote control) repeatedly to select
“PRESET SEARCH”.
1
Carry out “Selecting the XM Satellite Radio
mode” on page 41.
2
Press SEARCH MODE (or SRCH MODE on
the remote control) repeatedly to select “ALL
CH SEARCH” or “CAT SEARCH”.
SET MENU
PRESET/TUNING
or
SEARCH MODE
MENU
SRCH MODE
EDIT
PRESET/TUNING
SET MENU
or
SEARCH MODE
MENU
EDIT
Front panel
VCR
Front panel
SRCH MODE
V-AUX
Remote control
Remote control
DTV/CBL
DVD
MD/CD-R
TUNER
VCR
CD
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED STEREO
TUNED STEREO
SP
A
SP
A
XM
XM
ALL CH SEARCH
PRESET SEARCH
or
3
To change the preset group (A to E), press
CATEGORY (or A-E/CAT. j / i on the remote
control) repeatedly.
PRESET/CH
A/B/C/D/E
or
CATEGORY
ENTER
NEXT
A-E/CAT.
Front panel
A-E/CAT.
Remote control
To change the preset number (1 to 8), press
PRESET/TUNING/CH l / h (or PRESET/CH
u / d on the remote control) repeatedly.
PRESET/CH
l PRESET/TUNING/CH h
or
ENTER
LEVEL
A-E/CAT.
Front panel
A-E/CAT.
Remote control
y
You can also select the preset number directly by pressing the
numeric buttons (1 to 8) on the remote control.
44
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
TUNED STEREO
SP
A
XM
CAT SEARCH
CD
XM SATELLITE RADIO TUNING
3
Press the numeric buttons to enter the
desired channel number.
For example, to enter the number 123, press the
numeric buttons as shown below.
STEREO
MUSIC
ENTERTAIN
1
2
3
Setting XM Satellite Radio preset
channels
You can use this feature to store up to 40 XM Satellite
Radio channels (eight preset numbers in five preset
groups, A1 to E8). You can then recall any preset channel
easily by selecting the preset group and number as
described in “Preset Search mode” on page 44.
The display changes as follows.
VCR
V-AUX
DTV/CBL
DVD
SP
A
MD/CD-R
TUNER
CD
XM
PRESET/TUNING
<XM> --1
FM/AM
XM
SEARCH MODE
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
STRAIGHT
l
PROGRAM
h
INPUT MODE
TONE CONTROL
VCR
V-AUX
DTV/CBL
DVD
SP
A
MD/CD-R
TUNER
CD
XM
3 4
1
V-AUX
DTV/CBL
SP
A
DVD
MD/CD-R
TUNER
CD
XM
<XM>123
4
If you enter fewer than three numbers, you
may press ENT. to tune to the channel
immediately or wait a few seconds to confirm
the entered channel number.
2,5
Search the XM Satellite Radio channel you
want to set as a preset channel.
To search the desired channel, carry out “All Channel
Search mode” on page 42, “Category Search mode”
on page 43, or “Direct Number Access mode” on
page 44.
VCR
V-AUX
DTV/CBL
SP
A
DVD
MD/CD-R
TUNER
CD
XM
[040] Deep Tra
When the channel number “040” is selected
ENT.
2
y
• If no button is pressed within a few seconds after entering onedigit or two-digit number, the unit automatically confirms the
entered channel number.
• Pressing a button other than numeric buttons or ENT. cancels
the direct number access procedure.
Press MEMORY on the unit (or remote
control during the TUNER mode).
The MEMORY indicator flashes for about five
seconds.
MEMORY
or
RETURN
MEMORY
MAN'L/AUTO FM
Front panel
Remote control
MEMORY
Flashes
45
BASIC
OPERATION
<XM> -12
VCR
MULTI CH
INPUT
BASS/TREBLE
XM SATELLITE RADIO TUNING
3
While the MEMORY indicator is flashing,
press CATEGORY (or A-E/CAT. j / i on the
remote control) to select a preset group
(A to E).
The group letter appears.
PRESET/CH
5
While the MEMORY indicator is flashing,
press MEMORY on the unit (or the remote
control) to preset the selected XM Satellite
Radio channel.
A colon appears next to the preset number for
confirmation, and the MEMORY indicator turns off.
A/B/C/D/E
MEMORY
or
CATEGORY
RETURN
or
ENTER
NEXT
A-E/CAT.
MEMORY
MAN'L/AUTO FM
A-E/CAT.
Remote control
Front panel
Remote control
Front panel
VCR
V-AUX
DTV/CBL
MD/CD-R
DVD
TUNER
CD
MEMORY
VCR
SP
A
C
SP
A
MD/CD-R
TUNER
CD
XM
Colon appears
PRESET/CH
l PRESET/TUNING/CH h
or
ENTER
LEVEL
A-E/CAT.
Front panel
V-AUX
A-E/CAT.
Remote control
DTV/CBL
DVD
MD/CD-R
TUNER
CD
MEMORY
SP
A
XM
C5 [040] Deep
Preset number
46
DVD
C5:[040] Deep
While the MEMORY indicator is flashing,
press PRESET/TUNING/CH l / h (or
PRESET/CH u / d on the remote control) to
select a preset number (1 to 8).
VCR
DTV/CBL
MEMORY
[040] Deep
Preset group
4
V-AUX
XM
Note
Presetting a new channel clears the former preset channel stored
in the same preset group and number.
XM SATELLITE RADIO TUNING
■
Status and error messages
If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel
display. In this case, read the cause and follow the corresponding remedies.
Message
Cause
Remedy
The XM Connect and Play digital antenna
accessory is not connected, or does not work
properly.
• Check the XM Connect and Play digital antenna
accessory connections.
UPDATING
The XM user encryption code is being updated.
• Wait until the encryption code is updated.
NO SIGNAL
The signal is too weak.
• Check the XM Connect and Play digital antenna
accessory connections and orient it for the best
reception.
LOADING
It takes longer than four seconds for audio or
text data to be decoded.
• Wait until the decoding process has finished.
OFF AIR
The XM Satellite Radio channel you selected is
not currently broadcasting any signal.
• Check the channel number again or select another
XM Satellite Radio channel.
<XM> - - -
The channel Station ID (SID) is no longer
available.
- - - / - - -
No artist name/feature or song/program title is
available.
<CAT> - - -
No channels are available for the selected
category.
BASIC
OPERATION
CHECK ANTENNA
• Select another channel category by pressing
CATEGORY (or A-E/CAT. j / i on the remote
control) repeatedly.
47
RECORDING
RECORDING
Recording adjustments and other operations are
performed from the recording components. Refer to the
operating instructions for those components.
(U.S.A. model)
VOLUME
STANDBY
/ON
PRESET/TUNING
A/B/C/D/E
FM/AM
XM
SEARCH MODE
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
1
L
AUDIO
R
2
CODE SET
TRANSMIT
SYSTEM
2
POWER
STANDBY
POWER
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
1
AMP
VCR
TV VOL
TV CH
TV MUTE
TV INPUT
VOLUME
If you playback a video source that uses scrambled or
encoded signals to prevent it from being dubbed, the
picture itself may be disturbed due to those signals.
1
Turn on the power of this unit and all
connected components.
2
Select the source component you want to
record from.
INPUT
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
or
AMP
VCR
Front panel
Remote control
3
Start playback (or select a broadcast station)
on the source component.
4
Start recording on the recording component.
y
Do a test recording before you start an actual recording.
48
Notes
• When this unit is set in the standby mode, you cannot record
between other components connected to this unit.
• The setting of TONE CONTROL, VOLUME, “SP LEVEL”
(page 57) and the sound field programs does not affect recorded
material.
• A source connected to the MULTI CH INPUT jacks of this unit
cannot be recorded.
• S-video and composite video signals pass independently
through this unit’s video circuits. Therefore, when recording or
dubbing video signals, if your video source component is
connected to provide only an S-video (or only a composite
video) signal, you can record only an S-video (or only a
composite video) signal to your VCR.
• Digital signals input to the DIGITAL INPUT jacks are not
output to the analog AUDIO OUT (L/R) jacks for recording.
You can only record analog signals.
• A given input source is not output on the same REC OUT
channel. (For example, the signal input from VCR IN is not
output on VCR OUT.)
• Check the copyright laws in your country to record from
records, CDs, radio, etc. Recording of copyrighted material may
infringe copyright laws.
■ Special considerations when recording
DTS software
The DTS signal is a digital bitstream. Attempting to
digitally record the DTS bitstream will result in noise
being recorded. Therefore, if you want to use this unit to
record sources that have DTS signals recorded on them,
the following considerations and adjustments need to be
made.
For DVDs and CDs encoded with DTS, when your player
is compatible with the DTS format, follow its operating
instructions to make a setting so that the analog signal will
be output from the player.
SOUND FIELD PROGRAM DESCRIPTIONS
SOUND FIELD PROGRAM DESCRIPTIONS
This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from
almost any sound source (stereo or multi-channel). This unit is also equipped with a YAMAHA digital sound field
processing (DSP) chip containing several sound field programs which you can use to enhance your playback experience.
Most of these sound field programs are precise digital recreations of actual acoustic environments found in famous
concert halls, music venues, and movie theaters.
y
The YAMAHA CINEMA DSP modes are compatible with all Dolby Digital, DTS, and Dolby Surround sources. Set the input mode to
AUTO (see page 31) to enable this unit to automatically switch to the appropriate digital decoder according to the input signal.
Notes
• This unit’s DSP sound field programs are recreations of real-world acoustic environments made from precise measurements taken in
the actual hall, etc. Thus you may notice variations in the strength of the reflections coming from the front, back, left and right.
• Feel free to choose a sound field program based on your listening preference, and not purely on the name of the program itself.
For movie/video sources
You can select from the following sound fields when playing movie or video sources. The sound fields marked “MULTI”
can be used with multi-channel sources, like DVD, digital TV, etc. Those marked “2-CH” can be used with 2-channel
(stereo) sources like TV programs, video tapes, etc
Program selection methods vary depending on sound field program types. For details on how to
select sound field programs, see “Selecting sound field programs” on pages 27 to 31.
Remote
control
button
Program
Features
STEREO:
2ch Stereo
Downmixes multi-channel sources to 2 channels (left and right) or plays back 2channel sources as is.
2
MUSIC:
Pop/Rock
This program lends an enthusiastic atmosphere to the sound, giving you the
feeling you are at an actual jazz or rock concert.
ENTERTAINMENT:
TV Sports
Though the presence sound field is relatively narrow, the surround sound field
employs the sound environment of a large concert hall. This effect enhances the
experience of watching various TV programs such as news, variety shows,
music programs or sports programs.
ENTERTAINMENT:
Mono Movie
This program is provided for reproducing monaural video sources (such as old
movies). The program produces the optimum reverberation to create sound
depth using only the presernce sound field.
ENTERTAINMENT:
Game
This program adds a deep and spatial feeling to video game sounds.
3
SOUND FIELD
PROGRAMS
1
Sources
MULTI
2-CH
49
SOUND FIELD PROGRAM DESCRIPTIONS
Remote
control
button
Program
Features
MOVIE THEATER:
Spectacle
CINEMA DSP processing. This program creates the extremely wide sound field
of a 70-mm movie theater. It precisely reproduces the source sound in detail,
making both the video and the sound field incredibly real. This is ideal for any
kind of video source encoded with Dolby Surround, Dolby Digital or DTS
(especially large-scale movie productions).
MOVIE THEATER:
Sci-Fi
CINEMA DSP processing. This program clearly reproduces dialog and sound
effects in the latest sound form for science fiction films, thus creating a broad
and expansive cinematic space amid silence. You can enjoy science fiction films
in a virtual-space sound field that includes Dolby Surround, Dolby Digital and
DTS-encoded software employing the most advanced techniques.
MOVIE THEATER:
Adventure
CINEMA DSP processing. This program is ideal for precisely reproducing the
sound design of the newest 70-mm and multi-channel soundtrack films. The
sound field is made to be similar to that of the newest movie theaters, so the
reverberations of the sound field itself are restrained as much as possible.
MOVIE THEATER:
General
CINEMA DSP processing. This program is for reproducing sounds from 70-mm
and multi-channel soundtrack films, and is characterized by soft and extensive
sound field.
SUR. STANDARD
Standard processing for the selected decoder.
SUR. ENHANCED
Enhanced processing for the selected decoder.
4
5
50
Sources
MULTI
2-CH
SOUND FIELD PROGRAM DESCRIPTIONS
For music sources
You can select from the following sound fields when playing music sources, like CD, FM/AM broadcasting, tapes, etc.
Program selection methods vary depending on sound field program types. For details on how to
select sound field programs, see “Selecting sound field programs” on pages 27 to 31.
Remote
control
button
Program
Features
STEREO:
2ch Stereo
2-channel (left and right) playback.
STEREO:
6ch Stereo
Use to increase the output stereo sources (in stereo) from all speakers. This
provides a larger sound field and is ideal for background music at parties, etc.
MUSIC:
Hall in Vienna
HiFi DSP processing. A classic shoe-box type concert hall with approximately
1700 seats. Pillars and ornate carvings create extremely complex reflections
which produce a very full, rich sound.
MUSIC:
The Bttm Line
HiFi DSP processing. This is the sound field at stage front in “The Bottom
Line”, a famous New York jazz club. The floor can seat 300 people to the left
and right in a sound field offering a real and vibrant sound.
MUSIC:
The Roxy Thtr
HiFi DSP processing. The ideal program for lively, dynamic rock music. The
data for this program was recorded at LA’s “hottest” rock club. The listener’s
virtual seat is at the center-left of the hall.
ENTERTAINMENT:
Disco
HiFi DSP processing. This program recreates the acoustic environment of a
lively disco in the heart of a big city. The sound is dense and highly
concentrated. It is also characterized by high-energy, “immediate” sound.
SUR. STANDARD
Standard processing for the selected decoder.
SUR. ENHANCED
Enhanced processing for the selected decoder.
2-CH
1
2
3
MULTI
2-CH
SOUND FIELD
PROGRAMS
5
Sources
51
ADVANCED OPERATIONS
ADVANCED OPERATIONS
■ Canceling the sleep timer
Using the sleep timer
Use this feature to automatically set this unit in the
standby mode after a certain amount of time. The sleep
timer is useful when you are going to sleep while this unit
is playing or recording a source. The sleep timer also
automatically turns off any external components
connected to AC OUTLET(S).
■ Setting the sleep timer
CODE SET
POWER
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
2
AMP
VCR
TV VOL
TV CH
TV MUTE
TV INPUT
VOLUME
1
Select a source and start playback on the
source component.
2
Press SLEEP repeatedly to set
the amount of time.
Each time you press SLEEP, the front
panel display changes as shown
below. The SLEEP indicator flashes
while switching the amount of time
for the sleep timer.
SLEEP 120min
SLEEP OFF
V-AUX
SLEEP
SLEEP 90min
SLEEP 30min
VCR
DTV/CBL
DVD
SLEEP 60min
MD/CD-R
TUNER
CD
TUNED
SP
A
HiFi DSP
VOLUME
SLEEP
dB
L
R
The SLEEP indicator lights up in the front panel
display, and the display returns to the selected sound
field program.
SLEEP indicator
VCR
V-AUX
DTV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED
SP
A
TV Sports
52
SLEEP OFF
y
SYSTEM
STANDBY
POWER
TV
SLEEP
The sleep timer setting can also be canceled by pressing
STANDBY on the remote control (or STANDBY/ON on the front
panel) to set this unit to the standby mode.
TRANSMIT
POWER
Press SLEEP repeatedly until “SLEEP OFF” appears in
the front panel display.
After a few seconds, “SLEEP OFF” disappears, and the
SLEEP indicator goes off.
VOLUME
SLEEP
dB
L
R
ADVANCED OPERATIONS
Manually adjusting speaker levels
You can adjust the output level of each speaker while
listening to a music source. This is also possible when
playing sources through the MULTI CH INPUT jacks.
Please note that this operation will override the level
adjustments made in “BASIC SETUP” (page 22) and “SP
LEVEL” (page 57).
AMP
VCR
TV VOL
TV CH
1
VOLUME
TV MUTE
TV INPUT
STEREO
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
MUTE
A SPEAKERS B
9
0
MOVIE
10
ENT.
EFFECT
2
PRESET/CH
LEVEL
SET MENU
FAVOR. MENU
TITLE
SRCH MODE
BAND
ENTER
A-E/CAT.
RETURN
ALL CH
4
A-E/CAT.
DISPLAY
MEMORY
REC
AUDIO
3
1
Press AMP.
2
Press LEVEL repeatedly to select the
speaker you want to adjust.
FRONT L
CENTER
FRONT R
SUR. R
SUR. B
SUR. L
SWFR
Front left speaker level
Center speaker level
Front right speaker level
Surround right speaker level
Surround back speaker level
Surround left speaker level
Subwoofer level
y
3
Press j / i to adjust the speaker output level.
The control range is from +10 dB to –10 dB.
4
Press ENTER when you have completed your
adjustment.
ADVANCED
OPERATION
Once you press LEVEL, you can also select the speaker by
pressing u / d.
y
This operation can also be performed using the controls on the
front panel. Press NEXT repeatedly to select the speaker you
want to adjust, then press LEVEL –/+ to adjust the output level.
53
SET MENU
SET MENU
You can use the following parameters in SET MENU to adjust a variety of system settings and customize the way this
unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening
environment.
■ BASIC SETUP
Use to quickly setup basic system parameters (see page 22).
■ MANUAL SETUP
Use to adjust speaker and system settings manually.
1 SOUND MENU
Use to manually adjust any speaker setting, alter the quality and tone of the sound output by the system or compensate for
video signal processing delays when using LCD monitors or projectors.
y
Most of the parameters described in SOUND MENU are set automatically when you perform “BASIC SETUP” (see page 22). You can
use SOUND MENU to make further adjustments.
Item
Features
Page
A)SPEAKER SET
Selects the size of each speaker, the speakers for low-frequency signal output, and the cross over
frequency.
56
B)SP LEVEL
Adjusts the output level of each speaker.
57
C)SP DISTANCE
Adjusts the delay time of each speaker.
57
D)CENTER GEQ
Adjusts the tonal quality of the center speaker.
57
E)LFE LEVEL
Adjusts the output level of the LFE channel for Dolby Digital or DTS signals.
57
F)D.RANGE
Adjusts the dynamic range for Dolby Digital or DTS signals.
57
G)AUDIO SET
Customizes the muting level and audio delay.
58
2 INPUT MENU
Use to reassign digital input/outputs and select the input mode.
Item
Features
Page
A)I/O ASSIGN
Assigns jacks according to the component to be used.
58
B)INPUT MODE
Selects the initial input mode of the source.
59
C)INPUT RENAME
Changes the name of the inputs.
59
3 OPTION MENU
Use to adjust the optional system parameters.
Item
Features
Page
A)DISPLAY SET
Adjusts the brightness of the display.
59
B)MEMORY GUARD
Locks sound field program parameters and other SET MENU settings.
59
C)PARAM. INI
Initializes the parameters of a group of sound field programs.
59
D)MULTI ZONE
Specifies the location of the speakers connected to the SPEAKERS B terminals.
60
E)XM RADIO SET
Displays the current reception level for the XM Connect and Play digital antenna accessory.
60
54
SET MENU
Using SET MENU
6
Press ENTER to enter the displayed menu.
Repeat steps 5 and 6 to navigate to and enter the items
you want to adjust.
To return to the previous menu level, press RETURN.
1
7
Press u / d to select the item you want to
adjust, then press j / i to change the setting
of the item.
Repeat this operation to select and adjust each setting.
To return to the previous menu level, press RETURN.
2,8
8
To exit, press SET MENU when finished.
Use the remote control to access and adjust each
parameter.
AMP
VCR
TV VOL
TV CH
VOLUME
TV MUTE
TV INPUT
STEREO
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
MUTE
A SPEAKERS B
9
0
MOVIE
10
ENT.
EFFECT
PRESET/CH
LEVEL
SET MENU
FAVOR. MENU
TITLE
BAND
SRCH MODE
ENTER
A-E/CAT.
RETURN
ALL CH
A-E/CAT.
DISPLAY
MEMORY
REC
AUDIO
3-7
y
You can change SET MENU parameters while the unit is
reproducing sound.
Note
You cannot change some SET MENU parameters while the unit
is in either cinema or music night listening mode.
1
Press AMP.
2
Press SET MENU.
“BASIC SETUP” appears in the front panel display.
3
Press u / d to display MANUAL SETUP.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby mode.
However, if the power cord is disconnected from the
AC outlet, or the power supply is cut for more than one
week, the stored data will be lost. If so, adjust the
items again.
MANUAL SETUP
Press ENTER to enter MANUAL SETUP.
1 SOUND MENU appears in the front panel display.
ADVANCED
OPERATION
4
1 SOUND MENU
5
Press u / d to display the desired menu.
1 SOUND MENU
2 INPUT MENU
3 OPTION MENU
55
SET MENU
1 SOUND MENU
Use to manually adjust any speaker setting or compensate
for video signal processing delays when using LCD
monitors or projectors. Most of the SOUND MENU
parameters are set automatically when you perform
“BASIC SETUP” (see page 22).
■ Speaker settings A)SPEAKER SET
Use to manually adjust any speaker setting.
y
If you are not satisfied with the bass sounds from your speakers,
you can change these settings according to your preference.
Front speakers FRONT
Choices: LARGE, SMALL
• Select LARGE if you have large front speakers. The
unit directs the entire range of the front left and right
channel signals to the front left and right speakers.
• Select SMALL if you have small front speakers. The
unit directs the low-frequency signals of the front
channel to the speakers selected with “BASS OUT”.
Center speaker CENTER
Choices: LRG, SML, NONE
• Select LRG if you have a large center speaker. The unit
directs the entire range of the center channel signal to
the center speaker.
• Select SML if you have a small center speaker. The
unit directs the low-frequency signals of the center
channel to the speakers selected with “BASS OUT”.
• Select NONE if you do not have a center speaker. The
unit directs all of the center channel signal to the front
left and right speakers.
Surround left/right speakers SUR. LR
Choices: LRG, SML, NONE
• Select LRG if you have large surround left and right
speakers. The entire range of the surround channel
signal is directed to the surround left and right
speakers.
• Select SML if you have small surround left and right
speakers. The low-frequency signals of the surround
channel are directed to the speakers selected with
“BASS OUT”.
• Select NONE if you do not have surround speakers.
This will set the unit to the Virtual CINEMA DSP
mode (see page 31) and automatically set the surround
back speaker setting (SUR. B) to NONE.
56
Surround back speaker SUR. B
Choices: LRG, SML, NONE
• Select LRG if you have a large surround back speaker.
• Select SML if you have a small surround back speaker.
The low-frequency signals of the surround back
channel are directed to the speakers selected with
“BASS OUT”, and the rest of the frequency signals are
directed to the surround back speaker.
• Select NONE if you do not have a surround back
speaker. The unit directs all of the surround back
channel signal to the surround left and right speakers.
Bass out BASS OUT
Low-frequency (bass) signals can be directed to the
subwoofer and/or the front left and right speakers
according to the characteristics of your system. This
setting also determines the routing of the LFE (lowfrequency effect) signals found in Dolby Digital or DTS
sources.
Choices: SWFR (subwoofer), FRONT, BOTH
• Select SWFR if you connect a subwoofer. LFE and
low-frequency signals from other channels are directed
to the subwoofer according to the speaker settings.
• Select FRONT if you do not use a subwoofer. LFE and
low-frequency signals from other channels are directed
to the front speakers according to the speaker settings
(even if you have previously set the front speakers to
SML).
• Select BOTH if you connect a subwoofer and you want
to output low-frequency signals from front channels to
both the front speakers and subwoofer. LFE and lowfrequency signals from other channels are also directed
to the subwoofer according to the speaker settings. Use
this function to reinforce low-frequency signals using
the subwoofer when playing back sources such as CDs.
Cross over CrossOver
Use this feature to select a cross-over (cut-off) frequency
for all low-frequency signals. All frequencies below the
selected frequency will be sent to the subwoofer.
Choices: 40Hz, 60Hz, 80Hz, 90Hz, 100Hz, 110Hz,
120Hz, 160Hz, 200Hz
Subwoofer phase SWFR PHASE
If bass sounds are lacking or unclear, use this feature to
switch the phase of your subwoofer.
Choices: NRM (normal), REV (reverse)
• Select NRM if you do not want to reverse the phase of
your subwoofer.
• Select REV to reverse the phase of your subwoofer.
SET MENU
■ Speaker level B)SP LEVEL
Use these settings to manually balance the level of each
speaker selected in SPEAKER SET (page 56).
Choices: –10.0 dB to +10.0 dB
• FL adjusts the balance of the front left speaker.
• FR adjusts the balance of the front right speaker.
• C adjusts the balance of the center speaker.
• SL adjusts the balance of the surround left speaker.
• SR adjusts the balance of the surround right speaker.
• SB adjusts the balance of the surround back speaker.
• SWFR adjusts the balance of the subwoofer.
■ Speaker distance C)SP DISTANCE
Use this feature to manually input the distance of each
speaker and adjust the delay applied to respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sound will arrive at the listening position at the same time.
Unit UNIT
Choices: meters (m), feet (ft)
Initial setting:
U.S.A. and Canada models: feet (ft)
Other models: meters (m)
• Select meters to input speaker distances in meters.
• Select feet to input speaker distances in feet.
■ Low-frequency effect level E)LFE LEVEL
Use to adjust the output level of the LFE (low-frequency
effect) channel according to the capacity of your
subwoofer or headphones. The LFE channel carries lowfrequency special effects which are only added to certain
scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Choices: –20 to 0 dB
Speaker SP LFE
Select to adjust the speaker LFE level.
Headphone HP LFE
Select to adjust the headphone LFE level.
Note
Depending on the “LFE LEVEL” setting, some signals may not
be output from the SUBWOOFER OUTPUT jack.
■ Dynamic range F)D.RANGE
Use to select the amount of dynamic range compression to
be applied to your speakers or headphones. This setting is
effective only when the unit is decoding Dolby Digital and
DTS signals.
Choices: MAX (maximum), STD (standard), MIN
(minimum)
Speaker SP D.R
Select to adjust the speaker compression.
Headphone HP D.R
Select to adjust the headphone compression.
• Select MAX for feature films.
• Select STD for general use.
• Select MIN for listening to sources at low volume
levels.
57
ADVANCED
OPERATION
Speaker distances
Choices: 0.3 to 24.0 m (1 to 80 ft)
• FRONT L adjusts the distance of the front left speaker.
Initial setting: 3.0 m (10.0 ft)
• FRONT R adjusts the distance of the front right
speaker. Initial setting: 3.0 m (10.0 ft)
• CENTER adjusts the distance of the center speaker.
Initial setting: 3.0 m (10.0 ft)
• SUR. L adjusts the distance of the surround left
speaker. Initial setting: 3.0 m (10.0 ft)
• SUR. R adjusts the distance of the surround right
speaker. Initial setting: 3.0 m (10.0 ft)
• SUR. B adjusts the distance of the surround back
speaker. Initial setting: 2.10 m (7.0 ft)
• SWFR adjusts the distance of the subwoofer. Initial
setting: 3.0 m (10.0 ft)
■ Center graphic equalizer D)CENTER GEQ
Use this feature to adjust the built-in 5-band graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments listening to the currently selected
source component or a test tone.
You can adjust 5 frequency bands:
100Hz, 300Hz, 1kHz, 3kHz, 10kHz
Choices: –6 to +6 dB
Initial setting: 0 dB
• Select ON to output test tones from the front left and
center speakers, and adjust the tonal quality of the
center speaker.
• Select OFF to stop the test tone and output the
currently selected source component.
SET MENU
■ Audio settings G)AUDIO SET
Use to customize this units overall audio settings.
Muting type MUTE TYP.
Use to adjust how much the mute function reduces the
output volume.
Choices: FULL, –20dB
• Select FULL to completely halt all output of sound.
• Select –20dB to reduce the current volume by 20 dB.
Audio delay A.DELAY
Use to delay the sound output and synchronize it with the
video image. This may be necessary when using certain
LCD monitors or projectors.
Choices: 0 to 160 ms
Tone bypass TC.BYPASS
Use to select whether audio output bypasses tone control
circuitry when TREBLE and BASS (page 26) are set to
0 dB.
Choices: AUTO, OFF
• Select AUTO if you want signals to bypass tone control
circuitry to provide the purest signal possible.
• Select OFF if you do not want signals to bypass tone
control circuitry.
2 INPUT MENU
Use to reassign digital input/outputs and select the input
mode.
■ Input/output assignment A)I/O ASSIGN
You can assign jacks according to the component to be
used if this unit’s initial settings do not correspond to your
needs. Change the following parameters to reassign the
respective jacks and effectively connect more components.
Once the inputs have been reassigned, you can select the
corresponding component by using INPUT on the front
panel or the input selector buttons on the remote control.
For COMPONENT VIDEO jacks A (C.V[A]) and B
(C.V[B])
Choices: [A] DVD, DTV/CBL, V-AUX, VCR
[B] DVD, DTV/CBL, V-AUX, VCR
For OPTICAL INPUT jacks 1 (IN (1)) and 2
(IN (2))
Choices: (1) CD, MD/CD-R, DVD, DTV/CBL, V-AUX,
VCR
(2) CD, MD/CD-R, DVD, DTV/CBL, V-AUX,
VCR
For COAXIAL INPUT jack 3 (IN (3))
Choices: CD, MD/CD-R, DVD, DTV/CBL, V-AUX,
VCR
Notes
• You cannot select a specific item more than once for the same
type of jack.
• When you connect a component to both the COAXIAL and
OPTICAL jacks, priority is given to the input signals from the
COAXIAL jack.
58
SET MENU
■ Input mode B)INPUT MODE
Use this feature to designate the input mode for sources
connected to the DIGITAL INPUT jacks when you turn on
this unit (see page 31 for details about the input mode).
Choices: AUTO, LAST
• Select AUTO to allow this unit to automatically detect
the type of input signal and select the appropriate input
mode.
• Select LAST to set this unit to automatically select the
last input mode used for that source.
Note
Even if LAST is selected, the last setting for the EXTD SUR.
button will not be recalled.
■ Input rename C)INPUT RENAME
Use this feature to change the name of the inputs in the
front panel display.
1
2
Press an input selector button to select the
input you want to change the name of.
Press AMP.
3
Press j / i to place the _ (under-bar) under
the space or the character you want to edit.
4
Press u / d to select the character you want,
then use j / i to move to the next space.
• You can use up to 8 characters for each input.
• Press d to change the character in the following
order, or press u to go in the reverse order:
A to Z, a space, 0 to 9, a space, a to z, a space,
symbols (#, *, –, +, etc.).
Repeat steps 1 through 4 to rename each
input.
6
To exit, press SET MENU when finished.
Use to adjust the optional system parameters.
■ Display settings A)DISPLAY SET
Dimmer DIMMER
Use to adjust the brightness of the front panel display.
Choices: –4 to 0
■ Memory guard B)MEMORY GUARD
Use this feature to prevent accidental changes to DSP
program parameter values and other system settings.
Choices: ON, OFF
Select ON to protect:
• DSP program parameters
• All SET MENU items
• All speaker levels
Note
When MEMORY GUARD is set to ON, you cannot select
any other SET MENU items.
■ Parameter initialization C)PARAM. INI
Use this feature to initialize the parameters for each sound
field program within a sound field program group. When
you initialize a sound field program group, all of the
parameter values within that group revert to their initial
settings.
Press the corresponding numeric button for the sound field
program that you want to initialize.
Choices: STEREO, MUSIC, ENTERTAINMENT,
MOVIE, STANDARD
Notes
• You cannot automatically revert to the previous parameter
settings once you initialize a sound field program group.
• You cannot separately initialize individual sound field
programs.
• You cannot initialize any program groups when “MEMORY
GUARD” is set to ON.
59
ADVANCED
OPERATION
5
3 OPTION MENU
SET MENU
■ Zone set D) MULTI ZONE
Use to specify the location of speakers connected to the
SPEAKERS B terminals.
Speaker B setting SP B
Use this feature to select the location of the front speakers
connected to the SPEAKERS B terminals.
Choices: FRONT, ZONE B
• Select FRONT to turn on/off SPEAKERS A and B
when the speakers connected to the SPEAKERS B
terminals are set in the main room.
• Select ZONE B if the speakers connected to the
SPEAKERS B terminals are set in another room. If
SPEAKERS A is turned OFF and SPEAKERS B is
turned ON, all the speakers including the subwoofer in
the main room are muted and the unit outputs sound
from SPEAKERS B only.
Notes
• If you connect headphones to the PHONES jack on the unit
when “SP B” is set to ZONE B, the sound is output from both
headphones and SPEAKERS B.
• If a DSP program is selected when “SP B” is set to ZONE B,
the unit automatically enters the Virtual CINEMA DSP mode.
■ XM Radio setting E)XM RADIO SET
XM Radio antenna XM ANT.
Use to check the current reception level for the XM
Connect and Play digital antenna accessory connected to
this unit. For the best reception, orient the XM Connect
and Play digital antenna accessory so that a value of XX%
or more is displayed here.
Range: NONE, 0 to 100%
Note
“NONE” is displayed if the XM Connect and Play digital antenna
accessory is not connected to this unit. If this happens, check the
antenna connections (see page 39).
60
ADVANCED SETUP MENU
ADVANCED SETUP MENU
The ADVANCED SETUP menu is displayed in the front
panel display.
2
y
• During the advanced setup procedure, audio output is muted.
• During the advanced setup procedure, only the STANDBY/ON,
STRAIGHT (EFFECT) and PROGRAM l / h buttons on the
front panel are available for operation.
Press PROGRAM l / h repeatedly to move
through the menu and select the item you
want to set up.
See the end of this section for a complete list of
available parameters.
l
PROGRAM
h
CAUTION
Be sure to set the speaker impedance before using this unit
to play back audio or video signals.
(U.S.A. model)
3
Press STRAIGHT (EFFECT) repeatedly to
toggle between the available parameters.
VOLUME
STRAIGHT
STANDBY
/ON
PRESET/TUNING
FM/AM
XM
SEARCH MODE
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
NEXT
EDIT
TUNING MODE
EFFECT
DISPLAY
CATEGORY
LEVEL
MAN'L/AUTO FM
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
l
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
L
AUDIO
R
4
1,4
1,3
2
Press STANDBY/ON to confirm your
selection.
STANDBY
/ON
1
Turn off the power to this unit, and while
holding down STRAIGHT (EFFECT), press
STANDBY/ON.
This unit turns on, and the ADVANCED SETUP
menu appears in the front panel display.
This completes the advanced setup procedure.
The settings you made are reflected the next time this
unit’s power is turned on.
STRAIGHT
EFFECT
While holding
down, press
STANDBY
/ON
ADVANCED
OPERATION
61
ADVANCED SETUP MENU
■ ADVANCED SETUP menu items
Change the initial settings (indicated in bold under each
parameter) to reflect the needs of your listening
environment.
Speaker impedance SP IMP.
Use to switch the speaker impedance for this unit.
Choices: 8 Ω MIN, 4 Ω MIN
• Select 8 Ω MIN to set the speaker impedance to 8 Ω .
• Select 4 Ω MIN to set the speaker impedance to 4 Ω .
<U.S.A., Canada, Australia, Korea, Asia and
General models only>
Remote REMOTE
Use to switch the ID for the remote control of this unit.
Choices: ID1, ID2
• Select ID1 to operate this unit using the default code.
• Select ID2 to operate this unit using an alternative
code.
Note
SP IMP.
Speaker
Front
If you use one set (A or B),
the impedance of each
speaker must be 4 Ω or
higher.
If you use two sets (A and
B), the impedance of each
speaker must be 8 Ω or
higher.
4 Ω ΜΙΝ
Center
Surround
Surround back
Front
The impedance of each
speaker must be 6 Ω or
higher.
If you use one set (A or B),
the impedance of each
speaker must be 8 Ω or
higher.
If you use two sets (A and
B), the impedance of each
speaker must be 16 Ω or
higher.*
8 Ω ΜΙΝ
Center
Surround
Surround back
*
Impedance level
The impedance of each
speaker must be 8 Ω or
higher.
The Canada model cannot use two separate speaker systems
(A and B) simultaneously when SP IMP. is set to 8 Ω MIN.
Factory presets PRESET
Use to reset all parameters to the factory presets (see
page 75).
Choices: CANCEL, RESET
• Select CANCEL if you do not want this unit’s
parameters to be initialized when you reset the factory
presets.
• Select RESET if you want all of this unit’s parameters
to be initialized when you reset the factory presets.
Note
This setting does not affect ADVANCED SETUP menu item
parameters.
62
You must also make settings for the remote control (see page 64).
< Asia and General models only >
Tuner TU
Use to switch the frequency step selection according to the
frequency spacing in your area.
Choices: AM10/FM100, AM9/FM50
• North, Central and South America:
AM10/FM100 (kHz)
• Other areas: AM9/FM50 (kHz)
REMOTE CONTROL FEATURES
REMOTE CONTROL FEATURES
In addition to controlling this unit, the remote control can also operate other A/V components made by YAMAHA and
other manufacturers. To control other components, you must set up remote control with the appropriate remote control
codes.
Control area
■ Controlling this unit
■ Controlling other components
The shaded areas below can be used to control this unit
when the AMP mode is selected. Press AMP to activate
the AMP mode.
The shaded areas below can be used to control other
components. Each button has a different function
depending on the selected components. Select the
component you want to control by pressing an input
selector button.
CODE SET
TRANSMIT
SYSTEM
POWER
POWER
TV
AV
CD
MD/CD-R
DTV/CBL
DVD
STANDBY
POWER
TUNER
SLEEP
MULTI CH IN
V-AUX
AMP
VCR
Press AMP
to control
this unit.
TV VOL
TV CH
TV MUTE
TV INPUT
STEREO
MUSIC
VOLUME
MUTE
ENTERTAIN
The buttons in the
dotted lines
(SYSTEM
POWER,
STANDBY,
SLEEP, MULTI CH
IN, VOLUME +/–,
MUTE and input
selector buttons)
function in any
mode.
CODE SET
/
buttons and the
input selector buttons switch
the function of the
component control area
below.
* Use the /
buttons to
control other components
regardless of whether they
are connected to this unit.
TRANSMIT
SYSTEM
STANDBY
POWER
MD/CD-R POWER
TUNER
CD
TV
1
2
3
4
SELECT
EXTD SUR.
DIRECT ST.
MULTI CH IN
V-AUX
AMP
VCR
TV VOL
TV CH
MOVIE
STANDARD
SLEEP
AV
DTV/CBL
DVD
POWER
VOLUME
TV VOL
TV MUTE
TV INPUT
STEREO
TV MUTE
MUSIC
TV CH
MUTE
5
6
7
A SPEAKERS B
9
NIGHT
0
8
STRAIGHT
10
EFFECT
LEVEL
PRESET/CH
TITLE
2
STANDARD
STEREO
SELECT
SET MENU
STANDARD
A SPEAKERS B
5
0
9
SRCH MODE
A-E/CAT.
RETURN
A-E/CAT.
DISPLAY
MEMORY
REC
AUDIO
DISC SKIP
2
7
TITLE
BAND
6
10
7
8
EFFECT
NIGHT
STRAIGHT
ENT.
SET10
MENU
A/B/C/D/E
PRESET/CH
TITLE ENTER
MENU
CATEGORY
ENTER DISPLAY
ALL CH
A-E/CAT.
REC
A-E/CAT.
RETURN
MEMORY
DISC SKIP
ENT.
EFFECT
SET MENU
SRCH MODE
BAND
CATEGORY
RETURN
4
EXTD SUR. DIRECT ST.
STRAIGHT
FAVOR. MENU
LEVEL
MOVIE
3
8
SELECT
NIGHT
9 PRESET/CH 0
LEVEL
DISPLAY
AUDIO
REC
ADVANCED
OPERATION
Component control
area
You can control up to 9
different components by
setting appropriate remote
control codes (see
page 64).
4
MUSIC
ENTERTAIN
EXTD SUR. DIRECT ST.
A SPEAKERS B
ENTER
MOVIE
3
1
6
5
MENU
BAND
1
ENT.
TV INPUT
ENTERTAIN
AUDIO
DISC SKIP
63
REMOTE CONTROL FEATURES
Setting remote control codes
1
You can control other components by setting the
appropriate remote control codes. Codes can be set up for
each input area. For a complete list of available remote
control codes, refer to “LIST OF REMOTE CONTROL
CODES” at the end of this manual.
Press an input selector button or /
to
select the component you want to set up.
CD
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
AMP
VCR
The following table shows the default component
(Library: component category) and the remote control
code for each area.
2
Remote Control Code Default Settings
Input area
Component
category
(Library)
Manufacturer
Default
YAMAHA
code
CD
CD
YAMAHA
0005
MD/CD-R
MD
YAMAHA
0024
TUNER
TUNER
YAMAHA
0023*1
0033*2
DVD
DVD
YAMAHA
0098
DTV/CBL
–
–
–
V-AUX
–
–
–
VCR
–
–
–
DVR
YAMAHA
0208
–
–
–
*1
*2
Press CODE SET using a ballpoint pen or
similar object.
The TRANSMIT indicator on the remote control
flashes twice.
TRANSMIT
CODE SET
3
Press the numeric buttons (0 to 9) to enter
the four-digit remote control code for the
component to be used.
Refer to “LIST OF REMOTE CONTROL CODES”
at the end of this manual.
U.K. and Europe models
Other models
STEREO
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
A SPEAKERS B
Note
9
0
10
ENT.
EFFECT
You may not be able to operate your YAMAHA component even
if a YAMAHA remote control code is initially set as listed above.
In this case, try to set other YAMAHA remote control code(s).
The TRANSMIT indicator on the remote control
flashes twice, and the remote control code for the
selected component is set.
Notes
• If the manufacturer of your component has more than one code,
try each of them until you find the correct one.
• If you wait for more than 30 seconds during step 3, the setup
process is canceled. If this happens, start over from step 2.
64
REMOTE CONTROL FEATURES
Controlling other components
Once you set the appropriate remote control codes, you
can use this remote to control your other components.
Note that some buttons may not correctly operate the
selected component. Use the input selector buttons to
select the component you want to operate. The remote
control automatically switches to the appropriate control
mode for that component.
1
2
CODE SET
TRANSMIT
STEREO
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
SYSTEM
POWER
POWER
TV
AV
CD
MD/CD-R
POWER
STANDBY
TUNER
7
SLEEP
A SPEAKERS B
DVD
9
MULTI CH IN
V-AUX
DTV/CBL
MOVIE
7
8
NIGHT
STRAIGHT
0
10
ENT.
B
EFFECT
8
9
0
AMP
VCR
3
4
TV VOL
TV CH
VOLUME
PRESET/CH
LEVEL
SET MENU
FAVOR. MENU
TITLE
SRCH MODE
BAND
C
ENTER
A-E/CAT.
RETURN
A-E/CAT.
DISPLAY
ALL CH
MEMORY
D
REC
5
6
1
2
3
4
5
6
7
8
9
0
A
A
TV INPUT
MUTE
STEREO
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
AUDIO
DISC SKIP
DVD player
VCR
Digital TV/
Cable TV
CD player
MD/CD recorder
Tuner
AV POWER
Power *1
Power *1
VCR power *3
Power *1
Power *1
Power *1
TV POWER
TV power *2
TV power *2
TV power
TV power *2
TV power *2
TV power *2
TV CH +
TV channel up *2
TV channel up *2
TV channel up
TV channel up *2
TV channel up *2
TV channel up *2
TV CH –
TV channel down *2
TV channel down *2
TV channel down
TV channel down *2
TV channel down *2
TV channel down *2
TV VOL +
TV volume up *2
TV volume up *2
TV volume up
TV volume up *2
TV volume up *2
TV volume up *2
TV VOL –
TV volume down *2
TV volume down *2
TV volume down
TV volume down *2
TV volume down *2
TV volume down *2
TV MUTE
TV mute *2
TV mute *2
TV mute
TV mute *2
TV mute *2
TV mute *2
TV INPUT
TV input *2
TV input *2
TV input
TV input *2
TV input *2
TV input *2
1-9, 0, +10
Numeric buttons
Numeric buttons
Numeric buttons
Numeric buttons
Numeric buttons
Preset stations (1-8)
TITLE
Title
PRESET/CH u Up
VCR channel up
Preset up (1-8)
PRESET/CH d Down
VCR channel down
Preset down (1-8)
j
Left
Preset down (A-E)
i
Right
Preset up (A-E)
ENTER
Play
RETURN
Return
REC/
DISC SKIP
Disc skip (player)
Rec
VCR rec *3
p
Play
Play
VCR play *3
Play
Play
w
Search backward
Search backward
VCR search
backward *3
Search backward
Search backward
f
Search forward
Search forward
VCR search forward *3 Search forward
Search forward
AUDIO
Audio
e
Pause
Pause
VCR pause *3
Pause
b
Skip backward
Skip backward
Skip backward
a
Skip forward
Skip forward
Skip forward
s
Stop
Stop
VCR stop *3
Stop
Stop
ENTER
Title/Index
Enter
Enter
Index
Index
MENU
Menu
DISPLAY
Display
Display
Display
Display
Disc Skip
Pause
Rec (MD)
ADVANCED
OPERATION
B
C
D
TV MUTE
*1
This button functions only when the original remote control of the component has a POWER button.
These buttons can operate your TV without switching the input if the remote control code is set in DTV/CBL or
.
When the remote control code for your TV is set up in both the DTV/CBL and
areas, priority is given to the signal in the
DTV/CBL area.
*3 These buttons can operate your VCR without switching the input to VCR if the remote control code is set in VCR.
*2
65
REMOTE CONTROL FEATURES
Switching library codes
You can select the unit you want to operate with the
remote control by entering the library code.
1
Press CODE SET using a ballpoint pen or
similar object.
The TRANSMIT indicator on the remote control
flashes twice.
Clearing set up remote control
codes
■ Clearing a setup remote control code for
component control
1
Press an input selector button or /
to
select the component control for which you
want to clear the remote control code.
TRANSMIT
CODE SET
2
Enter the code number “9991” or “9992” (see
the table below).
The TRANSMIT indicator on the remote control
flashes twice, and the library code is changed.
AMP library
code
(remote
control
setting)
Function
9991
To operate this unit
using the default code.
9992
To operate this unit
using an alternative
code.
Remote
control ID
(unit setting:
see page 62)
MD/CD-R
TUNER
SLEEP
DVD
DTV/CBL
V-AUX
MULTI CH IN
VCR
2
AMP
Press CODE SET using a ballpoint pen or
similar object.
The TRANSMIT indicator on the remote control
flashes twice.
TRANSMIT
ID1
(initial setting)
CODE SET
ID2
When using multiple YAMAHA receivers/amplifiers, you
may be able to operate the other components simultaneously
with the default code setting. In this case, set one of the
alternative codes to operate this unit separately.
Note
You must also make settings for the receiver/amplifier.
66
CD
3
Enter the code number “0000”.
The TRANSMIT indicator on the remote control
flashes twice, and the remote control code for the
selected component is cleared.
y
• If you do not press any button within 30 seconds after step 2,
the clearing process is canceled. If this happens, start over from
step 1.
• You can clear all setup remote control codes at once by entering
the code number “9990”.
EDITING SOUND FIELD PARAMETERS
EDITING SOUND FIELD PARAMETERS
What is a sound field
What really creates the rich, full tones of a live instrument
are the multiple reflections from the walls of the room. In
addition to making the sound “live”, these reflections
enable us to tell where the player is situated, and the size
and shape of the room in which we are sitting.
Changing parameter settings
You can enjoy good quality sound with the factory preset
parameters. Although you do not have to change the initial
settings, you can change some of the parameters to better
suit the input source or your listening room.
MUTE
CODE SET
■ Elements of a sound field
TRANSMIT
SYSTEM
In any environment, in addition to the direct sound coming
straight to our ears from the player’s instrument, there are
two distinct types of sound reflections that combine to
make up the sound field:
MUSIC
ENTERTAIN
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
POWER
MD/CD-R
TUNER
SLEEP
DTV/CBL
V-AUX
MULTI CH IN
9
AMP
LEVEL
POWER
TV
AV
CD
DVD
A SPEAKERS B
1
0
10
Reverberations
These are caused by reflections from more than one
surface – walls, ceiling, the back of the room – so
numerous that they merge together to form a continuous
sonic “afterglow”. They are non-directional, and lessen
the clarity of the direct sound.
PRESET/CH
ENT.
SET MENU
FAVOR. MENU
TITLE
SRCH MODE
BAND
ENTER
TV VOL
TV CH
TV MUTE
TV INPUT
VOLUME
RETURN
A-E/CAT.
DISPLAY
ALL CH
MEMORY
REC
AUDIO
3,4
DISC SKIP
1
Press AMP.
2
Select the sound field program you want to
adjust.
Direct sound, early reflections and subsequent
reverberation taken together help us to determine the
subjective size and shape of the room, and it is this
information that the digital sound field processor
reproduces in order to create sound fields.
If you could create the appropriate early reflections and
subsequent reverberations in your listening room, you
would be able to create your own listening environment.
The acoustics in your room could be changed to those of a
concert hall, a dance floor, or virtually any size room at
all. This ability to create sound fields at will is exactly
what YAMAHA has done with the digital sound field
processor.
2
EFFECT
VCR
A-E/CAT.
Early reflections
Reflected sounds reach our ears extremely rapidly (50 ms
– 100 ms after the direct sound), after reflecting from one
surface only – for example, from the ceiling or a wall.
Early reflections actually add clarity to the direct sound.
MOVIE
STEREO
STANDBY
POWER
AMP
STEREO
MUSIC
ENTERTAIN
MOVIE
1
2
3
4
STANDARD
SELECT
EXTD SUR.
DIRECT ST.
5
6
7
8
NIGHT
STRAIGHT
A SPEAKERS B
9
0
10
ENT.
EFFECT
3
Press u / d to select
the parameters.
PRESET/CH
ENTER
A-E/CAT.
4
Press j / i to change
the parameter value.
A-E/CAT.
PRESET/CH
ADDITIONAL
INFORMATION
ENTER
A-E/CAT.
A-E/CAT.
y
If you press and hold j / i to change the parameter value, the
front panel display automatically stops at the factory preset
parameter momentarily.
67
EDITING SOUND FIELD PARAMETERS
5
Repeat steps 2 through 4 as necessary to
change other program parameters.
Note
You cannot change parameter values when “MEMORY GUARD”
is set to ON. If you want to change the parameter values, set
“MEMORY GUARD” to OFF (see page 59).
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter values will return to the
factory settings. If this happens, edit the parameter
value again.
■ Resetting parameters to the factory
presets
Use PARAM. INI (see page 59).
68
SOUND FIELD PARAMETER DESCRIPTIONS
SOUND FIELD PARAMETER DESCRIPTIONS
You can adjust the values of certain digital sound field parameters so the sound fields are recreated accurately in your
listening room. Not all of the following parameters are found in every program.
■ DSP LEVEL (DSP level)
Function:
Description:
Control range:
Adjusts the level of all the DSP effect sounds within a narrow range.
Depending on the acoustics of your listening room, you may want to increase or decrease the DSP
effect level relative to the level of the direct sound.
–6 dB to +3 dB
■ INIT.DLY (Initial delay)
Function:
Description:
Control range:
Changes the apparent distance from the source sound by adjusting the delay between the direct sound
and the first reflection heard by the listener.
The smaller the value, the closer the sound source seems to the listener. The larger the value, the farther
it seems. For a small room, set to a small value. For a large room, set to a large value.
1 to 99 msec
Source Sound
Time
Time
Time
Delay
Level
Level
Level
Early
Reflections
Delay
Delay
Sound Source
Reflection Face
Small value = 1 ms
Large value = 99 ms
For 2ch Stereo:
■ DIRECT (Direct)
Function:
Choices:
Bypasses this unit’s decoders and DSP processors for pure high fidelity sound when playing 2-channel
analog sources. The AUTO setting is effective only when BASS and TREBLE are set to 0 dB.
AUTO, OFF
Notes
69
ADDITIONAL
INFORMATION
• When multi-channel signals (Dolby Digital and DTS) are input, they are downmixed to 2 channels and output from the front left and
right speakers.
• When “BASS OUT” is set to BOTH, or “FRONT” set to SMALL and “BASS OUT” set to SWFR, front left and right speaker lowfrequency signals are redirected to the subwoofer.
SOUND FIELD PARAMETER DESCRIPTIONS
For 6ch Stereo:
Function:
Control range:
These parameters adjust the volume level for each channel in 6-channel stereo mode.
0 to 100%
■ CT LEVEL (Center level)
■ SL LEVEL (Surround left level)
■ SR LEVEL (Surround right level)
■ SB LEVEL (Surround back level)
For PRO LOGIC IIx Music and PRO LOGIC II Music:
■ PANORAMA (Panorama)
Function:
Choices:
Sends stereo signals to the surround speakers as well as the front speakers for a wraparound effect.
OFF, ON
■ DIMENSION (Dimension)
Function:
Control range:
Gradually adjusts the sound field either towards the front or towards the rear.
–3 (towards the rear) to +3 (towards the front), initial setting is STD (standard).
■ CT WIDTH (Center width)
Function:
Control range:
Initial setting:
Adjusts the center image from all three front speakers to varying degrees. A larger value adjusts the
center image towards the front left and right speakers.
0 (center channel sound is output only from center speaker) to 7 (center channel sound is output only
from front left and right speakers)
3
Note
This parameter can be set only when SUR. STANDARD is selected.
For DTS Neo:6 Music:
■ C. IMAGE (Center image)
Function:
Control range:
Initial setting:
Adjusts the center image from all three front speakers to varying degrees.
0 to 1.0
0.3
Note
This parameter can be set only when SUR. STANDARD is selected.
70
TROUBLESHOOTING
TROUBLESHOOTING
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the
nearest authorized YAMAHA dealer or service center.
■ General
Problem
This unit fails to turn
on when STANDBY/
ON (or SYSTEM
POWER) is pressed,
or enters the standby
mode soon after the
power has been
turned on.
No sound
Cause
Remedy
Refer to
page
The power cord is not connected or the
plug is not completely inserted.
Connect the power cord firmly.
—
The impedance setting is incorrect.
Set the impedance to match your speakers.
62
The protection circuitry has been
activated.
Make sure all speaker wire connections on this unit
and on all speakers are secure and that the wire for
each connection does not touch anything other than
its respective connection.
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit in the standby mode, disconnect the
power cord, plug it back in after 30 seconds, then use
it normally.
—
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
14-20
The input mode is set to DTS or
ANALOG.
Select AUTO.
31
No appropriate input source has been
selected.
Select an appropriate input source with INPUT,
MULTI CH INPUT (or MULTI CH IN on the remote
control) or the input selector buttons.
25
Speaker connections are not secure.
Secure the connections.
12
The front speakers to be used have not
been selected properly.
Select the front speakers with SPEAKERS A and/or
B.
25
The volume is turned down.
Turn up the volume.
—
The sound is muted.
Press MUTE or any operation button of this unit to
resume audio output, then adjust the volume.
26
The input mode is set to ANALOG while
playing a source encoded with a DTS
signal.
Set the input mode to AUTO or DTS.
31
Signals this unit cannot reproduce are
being received from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by this
unit.
—
11-13
ADDITIONAL
INFORMATION
71
TROUBLESHOOTING
Problem
The sound suddenly
goes off.
Cause
Remedy
Refer to
page
Check that the impedance selector setting is correct.
62
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned the unit off.
Turn on the power, and play the source again.
—
The sound is muted.
Press MUTE to cancel a mute.
26
Only the speaker on
one side can be
heard.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
12
Incorrect balance settings in SET MENU.
Adjust the SP LEVEL settings.
57
Only the center
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound from the
effect speakers.
The sound field programs are turned off.
Press STRAIGHT (EFFECT) to turn them on.
31
You are using a source or program
combination that does not output sound
from all channels.
Try another sound field program.
The output level of the center speaker is
set to minimum.
Raise the level of the center speaker.
57
“CENTER SP” in SET MENU is set to
NONE.
Select the appropriate setting for the center speaker.
56
One of the HiFi DSP programs (except for
6ch Stereo) has been selected.
Try another sound field program.
The output level of the surround speakers
is set to minimum.
Raise the output level of the surround speakers.
57
“SUR. LR” in SET MENU is set to
NONE.
Select the appropriate setting for the surround left and
right speakers.
56
A monaural source is being played with
STRAIGHT.
Press STRAIGHT (EFFECT) to turn on the sound
fields.
—
“SUR. LR” in SET MENU is set to
NONE.
If the surround left and right speakers are set to
NONE, the surround back speaker setting is
automatically set to NONE. Select the appropriate
setting for the surround speakers.
56
“SUR. B” in SET MENU is set to NONE.
Select LRG or SML.
56
“BASS OUT” in SET MENU is set to
FRONT when a Dolby Digital or DTS
signal is being played.
Select SWFR or BOTH.
56
“BASS OUT” in SET MENU is set to
SWFR or FRONT when a 2-channel
source is being played.
Select BOTH.
56
No sound from the
center speaker.
No sound from the
surround speakers.
No sound from the
surround back
speaker.
No sound from the
subwoofer.
The protection circuitry has been activated
because of a short circuit, etc.
The source does not contain low bass
signals.
72
27, 49
27, 49
TROUBLESHOOTING
Problem
Cause
Remedy
Refer to
page
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator in
the front panel
display does not light
up.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operating
instructions for your component.
—
The input mode is set to ANALOG.
Set the input mode to AUTO or DTS.
31
A “humming” sound
can be heard.
Incorrect cable connections.
Firmly connect the audio plugs. If the problem
persists, the cables may be defective.
—
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the OUT
(REC) jacks of this unit is turned off.
Turn on the power to the component.
—
The sound effect
cannot be recorded.
It is not possible to record the sound effect
with a recording component.
A source cannot be
recorded by a digital
recording component
connected to this
DIGITAL OUTPUT
jack.
The source component is not connected to
this unit’s DIGITAL INPUT jacks.
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT jacks.
Connect the source component to the DIGITAL
INPUT jacks.
14-18
The source component is not connected to
this unit’s analog AUDIO IN jacks.
Connect the source component to the analog AUDIO
IN jacks.
14-18
The sound field
parameters and some
other settings on this
unit cannot be
changed.
“MEMORY GUARD” in SET MENU is
set to ON.
Select OFF.
59
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the AC power cord from the outlet and
then plug it in again after about 30 seconds.
—
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short circuited.
Make sure all speaker cables are connected correctly.
12
There is noise
interference from
digital or radio
frequency equipment,
or this unit.
This unit is too close to the digital or highfrequency equipment.
Move this unit further away from such equipment.
—
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
This unit suddenly
turns into the standby
mode.
The internal temperature becomes too
high and the overheat protection circuitry
has been activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
Some components cannot record the
Dolby Digital or DTS sources.
ADDITIONAL
INFORMATION
73
TROUBLESHOOTING
■ Tuner
Problem
Cause
FM stereo reception is
noisy.
FM
AM
Remedy
Refer
to page
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Check the antenna connections.
Try using a high-quality directional FM
antenna.
19
Use the manual tuning method.
34
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multipath interference.
Adjust the antenna position to eliminate
multipath interference.
—
The desired station
cannot be tuned in with
the automatic tuning
method.
The signal is too weak.
Use a high-quality directional FM antenna.
19
Use the manual tuning method.
34
Previously preset
stations can no longer
be tuned in.
This unit has been disconnected for a
long period.
Preset the stations again.
34
The desired station
cannot be tuned in with
the automatic tuning
method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections
and orient it for the best reception.
—
Use the manual tuning method.
34
There are continuous
crackling and hissing
noises.
Noises result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
—
There are buzzing and
whining noises.
A TV set is being used nearby.
Move this unit away from the TV.
—
■ Remote control
Problem
The remote control
does not work nor
function properly.
Cause
Refer to
page
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel.
7
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
3
The remote control code was not correctly
set.
Set the remote control code correctly using “LIST OF
REMOTE CONTROL CODES” at the end of this
manual.
64
Try to set another code for the same remote control
using “LIST OF REMOTE CONTROL CODES” at
the end of this manual.
64
Switch the library code.
66
The remote control ID and this unit’s ID
do not match.
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
74
Remedy
RESETTING THE FACTORY PRESETS
RESETTING THE FACTORY PRESETS
If you want to reset all of your unit’s parameters for any
reason, do the following. This procedure completely resets
ALL parameters, including the SET MENU, level, assign
and tuner presets.
Be sure this unit is in standby mode.
4
Press STANDBY/ON to confirm your
selection.
STANDBY
/ON
(U.S.A. model)
VOLUME
If you selected “RESET”, the unit is reset to its
factory presets and switches to standby mode.
If you selected “CANCEL”, the unit switches to
standby mode and nothing is reset.
STANDBY
/ON
PRESET/TUNING
FM/AM
XM
SEARCH MODE
A/B/C/D/E
l PRESET/TUNING/CH h
MEMORY
LEVEL
MAN'L/AUTO FM
TUNING MODE
DISPLAY
CATEGORY
NEXT
EDIT
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
l
STRAIGHT
PROGRAM
h
VIDEO AUX
INPUT MODE
MULTI CH
INPUT
EFFECT
TONE CONTROL
BASS/TREBLE
VIDEO
SILENT CINEMA
1,4
1
1,3
L
AUDIO
R
2
With the unit in standby mode, hold down
STRAIGHT (EFFECT) on the front panel and
press STANDBY/ON.
The ADVANCED SETUP menu appears in the front
panel display.
STRAIGHT
EFFECT
While holding
down, press
STANDBY
/ON
y
To cancel the initialization procedure without making any
changes, press STANDBY/ON.
2
Press PROGRAM l / h repeatedly to move
through the menu and select “PRESET”.
l
h
ADDITIONAL
INFORMATION
3
PROGRAM
Press STRAIGHT (EFFECT) to select the
desired setting.
STRAIGHT
EFFECT
RESET
CANCEL
To reset the unit to its factory presets.
To cancel without making any changes.
75
GLOSSARY
GLOSSARY
Audio formats
■ Dolby Digital
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (left, center, and right), and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (low frequency effect), the system has
a total of 5.1-channels (LFE is counted as 0.1 channel). By
using 2-channel stereo for the surround speakers, more
accurate moving sound effects and surround sound
environment are possible than with Dolby Surround. The
wide dynamic range (from maximum to minimum
volume) reproduced by the 5 full-range channels and the
precise sound orientation generated using digital sound
processing provide listeners with previously unheard of
excitement and realism.
With this unit, any sound environment from monaural up
to a 5.1-channel configuration can be freely selected for
your enjoyment.
■ Dolby Digital EX
Dolby Digital EX creates 6 full-bandwidth output
channels from 5.1-channel sources. This is done using a
matrix decoder that derives 3 surround channels from the
2 in the original recording. For the best results, Dolby
Digital EX should be used with movie sound tracks
recorded with Dolby Digital Surround EX. With this
additional channel, you can experience more dynamic and
realistic moving sound especially with scenes with
“flyover” and “fly-around” effects.
■ Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround software.
This new technology enables a discrete 5-channel
playback with 2 front left and right channels, 1 center
channel, and 2 surround left and right channels (instead of
only 1 surround channel for conventional Pro Logic
technology). Music and Game modes are also available for
2-channel sources in addition to the Movie mode.
■ Dolby Pro Logic IIx
Dolby Pro Logic IIx is a new technology enabling discrete
multi-channel playback from 2-channel or multi-channel
sources. There is a Music mode for music, a Movie mode
for movies (for 2-channel sources only) and a Game mode
for games.
76
■ Dolby Surround
Dolby Surround uses a 4 channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range.
Dolby Surround is widely used with nearly all video tapes
and laser discs, and in many TV and cable broadcasts as
well. The Dolby Pro Logic decoder built into this unit
employs a digital signal processing system that
automatically stabilizes the volume on each channel to
enhance moving sound effects and directionality.
■ DTS 96/24
DTS 96/24 offers an unprecedented level of audio quality
for multi-channel sound on DVD-Video, and is fully
backward-compatible with all DTS decoders. “96” refers
to a 96 kHz sampling rate (compared to the typical 48 kHz
sampling rate). “24” refers to 24-bit word length. DTS 96/
24 offers sound quality transparent to the original 96/24
master, and 96/24 5.1-channel sound with full-quality fullmotion video for music programs and motion picture
soundtracks on DVD-video.
■ DTS (Digital Theater Systems)
Digital Surround
DTS digital surround was developed to replace the analog
soundtracks of movies with a 6-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. Digital Theater Systems Inc.
has developed a home theater system so that you can enjoy
the depth of sound and natural spatial representation of
DTS digital surround in your home. This system produces
practically distortion-free 6-channel sound (technically, a
left, right and center channels, 2 surround channels, plus
an LFE 0.1 channel as a subwoofer, for a total of 5.1channels). The unit incorporates a DTS-ES decoder that
enables 6.1-channel reproduction by adding the surround
back channel to existing 5.1-channel format.
■ Neo:6
Neo:6 decodes the conventional 2-channel sources for 6
channel playback by the specific decoder. It enables
playback with the full-range channels with higher
separation just like digital discrete signal playback. Two
modes are available; “Music mode” for playing music
sources and “Cinema mode” for movies.
GLOSSARY
Sound field programs
Audio information
■ CINEMA DSP
■ ITU-R
Since the Dolby Surround and DTS systems were
originally designed for use in movie theaters, their effect
is best felt in a theater having many speakers and designed
for acoustic effects. Since home conditions, such as room
size, wall material, number of speakers, and so on, can
differ so widely, it’s inevitable that there are differences in
the sound heard as well. Based on a wealth of actually
measured data, YAMAHA CINEMA DSP uses
YAMAHA original sound field technology to combine
Dolby Pro Logic, Dolby Digital and DTS systems to
provide the visual and audio experience of movie theater
in the listening room of your own home.
ITU-R is the radio communication sector of the ITU
(International Telecommunication Union). ITU-R
recommends a standard speaker placement which is used
in many critical listening rooms, especially for mastering
purposes.
■ SILENT CINEMA
YAMAHA has developed a natural, realistic sound effect
DSP algorithm for headphones.
Parameters for headphones have been set for each sound
field so that accurate representations of all the sound field
programs can be enjoyed on headphones.
■ Virtual CINEMA DSP
YAMAHA has developed a Virtual CINEMA DSP
algorithm that allows you to enjoy DSP sound field
surround effects even without any surround speakers by
using virtual surround speakers.
It is even possible to enjoy Virtual CINEMA DSP using a
minimal two-speaker system that does not include a center
speaker.
■ LFE 0.1 channel
This channel is for the reproduction of low bass signals.
The frequency range for this channel is 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low frequency range compared to the full-range
reproduced by the other 5/6 channels in Dolby Digital or
DTS 5.1/6.1-channel systems.
■ PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for “pulse code
modulation”, the analog signal is encoded as pulses and
then modulated for recording.
■ Sampling frequency and number of
quantized bits
When digitizing an analog audio signal, the number of
times the signal is sampled per second is called the
sampling frequency, while the degree of fineness when
converting the sound level into a numeric value is called
the number of quantized bits.
The range of rates that can be played back is determined
based on the sampling rate, while the dynamic range
representing the sound level difference is determined by
the number of quantized bits. In principle, the higher the
sampling frequency, the wider the range of frequencies
that can be played back, and the higher the number of
quantized bits, the more finely the sound level can be
reproduced.
ADDITIONAL
INFORMATION
77
GLOSSARY
Video signal information
■ Component video signal
With the component video signal system, the video signal
is separated into the Y signal for the luminance and the PB
and PR signals for the chrominance. Color can be
reproduced more faithfully with this system because each
of these signals is independent. The component signal is
also called the “color difference signal” because the
luminance signal is subtracted from the color signal.
A monitor with component input jacks is required in order
to use the component signal for output.
■ Composite video signal
With the composite video signal system, the video signal
is composed of three basic elements of a video picture;
color, brightness and synchronization data. A composite
video jack on a video component transmits these three
elements combined.
■ S-video signal
With the S-video signal system, the video signal normally
transmitted using a pin cable is separated and transmitted
as the Y signal for the luminance and the C signal for the
chrominance through the S-video cable. Using the
S VIDEO jack eliminates video signal transmission loss
and allows recording and playback of even more beautiful
images.
78
SPECIFICATIONS
SPECIFICATIONS
AUDIO SECTION
VIDEO SECTION
• Minimum RMS Output Power for Front, Center, Surround,
Surround back
20 Hz to 20 kHz, 0.06% THD, 8 Ω ....................................... 85 W
• Video Signal Type .......................................................... PAL/NTSC
• Maximum Power (EIAJ)
[Asia, Korea and General models]
1 kHz, 10% THD, 8 Ω .......................................................... 125 W
• Dynamic Power (IHF)
8/6/4/2 Ω ........................................................ 115/150/185/230 W
• DIN Standard Output Power [U.K. and Europe models]
1 kHz, 0.7% THD, 4 Ω .........................................................130 W
• IEC Output Power [U.K., Europe and Asia models]
1 kHz, 0.06% THD, 8 Ω .........................................................95 W
• Signal to Noise Ratio ................................................ 50 dB or more
• Frequency Response (MONITOR OUT)
Composite, S-video .................................. 5 Hz to 10 MHz, –3 dB
Component ............................................... 5 Hz to 60 MHz, –3 dB
FM SECTION
• Tuning Range
[U.S.A. and Canada models] ........................... 87.5 to 107.9 MHz
[Asia and General models] ........ 87.5/87.50 to 108.0/108.00 MHz
[Other models] ............................................ 87.50 to 108.00 MHz
• Usable Sensitivity (IHF)........................................ 1.0 µV (11.2 dBf)
• Damping Factor (IHF)
20 Hz to 20 kHz, 8 Ω................................................... 120 or more
• Signal to Noise Ratio (IHF)
Mono/Stereo .............................................................. 76 dB/70 dB
• Frequency Response
CD terminal to Front L/R ...................... 10 Hz to 100 kHz, –3 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo ................................................................ 0.2%/0.3%
• Total Harmonic Distortion
CD, etc. to Front L/R (20 Hz to 20 kHz, 40 W, 8 Ω)
.................................................................................. 0.06% or less
• Stereo Separation (1 kHz) ....................................................... 42 dB
• Signal to Noise Ratio (IHF-A Network)
CD (250 mV) to Front L/R, Effect Off .................. 100 dB or more
AM SECTION
• Residual Noise (IHF-A Network)
Front L/R ............................................................... 150 µV or less
• Channel Separation (1 kHz/10 kHz)
CD (5.1 kΩ terminated) to Front L/R .......... 60 dB/45 dB or more
• Tone Control (Front L/R)
BASS Boost/Cut ..................................................... ±10 dB/60 Hz
TREBLE Boost/Cut .............................................. ±10 dB/20 kHz
• Frequency Response .......................... 20 Hz to 15 kHz, +0.5, –2 dB
• Tuning Range
[U.S.A. and Canada models] .............................. 530 to 1710 kHz
[Asia and General models] ................. 530/531 to 1710/1611 kHz
[Other models] ................................................... 531 to 1611 kHz
• Usable Sensitivity ............................................................. 300 µV/m
GENERAL
• Input Sensitivity/Input Impedance
CD, etc. ................................................................. 200 mV/47 kΩ
MULTI CH INPUT ............................................... 200 mV/47 kΩ
• Power Supply
[U.S.A. and Canada models] .............................. AC 120 V, 60 Hz
[Australia model] ............................................... AC 240 V, 50 Hz
[Korea model] .................................................... AC 220 V, 60 Hz
[U.K. and Europe models] ................................. AC 230 V, 50 Hz
[General model] .............. AC 110/120/220/230–240 V, 50/60 Hz
[Asia model] ................................... AC 220/230–240 V, 50/60 Hz
• Output Level/Output Impedance
REC OUT ............................................................. 200 mV/1.2 kΩ
SUBWOOFER.............................................................. 4 V/1.2 kΩ
• Power Consumption
[U.S.A. and Canada models] ................................. 350 W/440 VA
[Other models] ................................................................... 360 W
• Phones Output .......................................................... 150 mV/100 Ω
• Standby Power Consumption ...................................... 0.1 W or less
• AC Outlets
[U.K. and Australia models] .............. 1 (Total 100 W maximum)
[U.S.A. and Canada models] .............. 2 (Total 100 W maximum)
[Europe, Asia and General models] ..... 2 (Total 50 W maximum)
• Dimensions (W x H x D) ................................. 435 x 161 x 416 mm
(17-1/8” x 6-5/16” x 16-3/8”)
79
ADDITIONAL
INFORMATION
• Weight ................................................................ 11 kg (24 lbs 4 oz)
LIST OF REMOTE CONTROL CODES
TV
A TANDY
0941
ABEX
1151
ADMIRA
1141
ADVENTURA 1131
AIKO
1121
AIWA
1481
AKAI
0331, 1101, 1111
ALBA
0431
ALLERON
1091
AMBASSADOR
1081
AMSTRAD
0481, 1081
ANAM
0251, 1041, 1051,
1061, 1071
ANAM NATIONAL 1041
AOC
0361, 1021, 1031,
1111, 1161
ARCHER
1161
AUDIOSONIC 1001
AUDIOVOX
1051, 1161
BAUER
0441
BAUR
1001
BEIJING
1511, 1551, 1561
BELCOR
1031
BELL & HOWELL 0981, 0991
BEON
1001
BRADFORD 1051
BROCKWOOD 1031
BROKSONIC 1161
BUSH
1001
CANDLE
0351, 0361, 0961,
0971, 1111, 1131
CAPEHART
1021
CARVER
0101
CATHAY
1001
CELEBRITY 0951
CENTURION 0411
CHANGHONG 1541, 1551, 1561,
1621
CITIZEN
0351, 0361, 0921,
0931, 0941, 0961,
0971, 1111, 1121,
1131
CLAIRTONE 1011
CLARIVOX
1001
CONCERTO 0351, 0971
CONROWA
1751
CONTEC
0901, 0911, 1011,
1051
CORANDO
0941
CRAIG
0251, 1051
CROWN
0941, 1051
CURTIS MATHES
0161, 0361,
0931, 0941,
0981, 1111
CXC
1051
DAEWOO
0291, 0301, 0331,
0721, 0941, 1001,
1031, 1121, 1191,
1531, 1581, 1591,
1601
DANSAI
1001
DAYTRON
0941, 1031
DECCA
0271, 1001
DIXI
0331, 1001, 1071
DUMONT
0891, 1031
DYNATECH 0881
ELECTROBAND
0951, 1011
ELECTROHOME
0941
ELECTRON
0941
APPENDIX-i
ELIN
ELTA
EMERSON
1001
0331
0001, 0021, 0061,
0071, 0081, 0091,
0111, 0811, 0821,
0831, 0841, 0851,
0861, 0871, 0901,
0921, 0941, 0981,
1011, 1031, 1051,
1081, 1091
ENVISION
0361, 1111
ERRES
1001
ETRON
0331
FERGUSON 1001
FINLUX
1001
FISHER
0171, 0801, 0981
FORMENTI
0441
FORMONTI
1001
FORTRESS
1141
FUJITSU
1091
FUNAI
1051, 1091, 1501,
1521
FUTURETECH 1051
GE
0131, 0161, 0201,
0751, 0761, 0771,
0781, 0791, 0811,
0861, 1041
GEC
0271, 1001
GEMINI
0391
GENEXXA
0431
GIBRALTER 0891, 1031, 1111
GOODMANS/TASHIKO
0271, 0661, 1001
GRANADA
1001
GRUNDIG
1781, 1791, 1801,
1811, 1821, 1831,
1841, 1851, 1861,
1871, 1881
GUNPY
1051, 1091
H/K
0721
HALLMARK 0861
HANSEATIC 1001
HARVARD
1051, 1061
HINARI
1001, 1091
HITACHI
0181, 0351, 0671,
0681, 0691, 0701,
0711, 0871, 0941,
0971, 1351
HYPSON
1001
IMA
1051
INDIANA
1001
INFINITY REFERENCE
0101
INTERFUNK 1001
ITT
0611
JANEIL
1131
JBL
0101
JCB
0951
JENSEN
0311
JINXING
1531, 1541, 1551,
1561, 1571, 1621,
1631, 1641, 1651,
1691, 1731
JVC
0261, 0281, 0641,
0651, 0661, 0841
KAWASHO
0901
KAYPANI
1021
KENWOOD
0361, 1031, 1111
KLOSS
0631, 0721, 1131
KTV
0921, 0941, 1011,
1051, 1111
LEYCO
1001
LG (GOLDSTAR)
0031, 0121,
0351, 0411, 0731,
0741, 0861, 0941,
0971, 1001, 1031,
1111, 1151
LIESENK & TTER 1001
LLOYTRON 0941
LOEWE
1001
LOGIK
0991, 1771
LUXMAN
0351, 0971
LXI
0101, 0621, 0761,
0861, 0981
MAGNAVOX 0101, 0341, 0391,
0401, 0411, 0421,
0581, 0591, 0601,
0611, 0631, 0661,
0961, 1111
MAJESTIC
0991
MARANTZ
0101, 0221, 0361,
1001, 1111
MARK
1001
MATSUI
0271, 0331, 1001
MEDIATOR
1001
MEGATRON 0691, 0861, 1161
MEI
1011
M-ELECTRONIC
1001
MEMOREX
0331, 0571, 0861,
0971, 0981, 0991,
1771
METZ
1791, 1831, 1891,
1901, 1911, 1921,
1931, 1941
MGA
0361, 0561, 0571,
0861, 1031, 1111
MIDLAND
0751, 0761, 0891,
0941, 1151
MITSUBISHI 0221, 0321, 0561,
0571, 0661, 0861,
1031, 1101, 1381
MONTGOMERY
1091
MOTOROLA 1041, 1141
MTC
0351, 0361, 0881,
0931, 0971, 1011,
1031, 1111
MULTITECH 0881, 1051
NAD
0551, 0621, 0861
NEC
0241, 0351, 0361,
0661, 0971, 1031,
1111, 1321, 1711
NECKERMANN
1001
NEI
1001
NIKKAI
0271, 0431, 1001,
1151
NIKKO
0861, 1111, 1121
NOVABEAM 0721
NTC
1121
ONWA
1051
OPTIMUS
0551
OPTONICA
0541, 1141
ORION
0831, 1001
OSAKI
0271, 1151
OTTO VERSAND
1001
PANASONIC 0101, 0191, 0251,
0751, 1041, 1311,
1371, 1431
PANDA
1541, 1721
PENNY
0161, 0361, 0521,
0531, 0621, 0731,
0751, 0761, 0781,
0791, 0861, 0931,
0941, 1031, 1041,
1111, 1151, 1161
PEONY
1561, 1621
PHILCO
0361, 0581, 0591,
0601, 0611, 0631,
0961, 1031, 1111
PHILIPS
0101, 0401, 1001
PHONOLA
1001
PILOT
0941, 1031, 1111
PIONEER
0511, 0551, 0871
PORTLAND 0941, 1031, 1121
PRICECLUB 0931
PRISM
0751
PROSCAN
0761
PROTECH
1001
PROTON
0501, 0861, 0941,
1021, 1161
PULSAR
0891
PULSER
1031
QUASAR
0251, 0751, 1041
QUELLE
1001
RADIO SHACK
0541, 0941,
1031, 1051,
1151
RADIOLA
1001
RCA
0051, 0141, 0151,
0181, 0411, 0491,
0531, 0761, 0771,
0871, 1031
REALISTIC
0541, 0861, 0941,
0971, 0981, 1031,
1051, 1111, 1151
RHAPSODY 1011
R-LINE
1001
RUNCO
0891, 1111
SAISHO
0331, 1081
SAMPO
0361, 0941, 1021,
1111, 1151
SAMSUNG
0331, 0341, 0351,
0361, 0861, 0931,
0941, 0971, 1001,
1031, 1111, 1151
SAMSUX
0941
SANYO
0171, 0231, 0271,
0661, 0801, 0911,
0981, 1231, 1251,
1261
SBR
1001
SCHEIDER
1001
SCIMITSU
1031
SCOTCH
0861
SCOTT
0831, 0861, 0941,
1031, 1051, 1091
SEARS
0101, 0161, 0171,
0351, 0481, 0521,
0621, 0761, 0801,
0861, 0971, 0981,
1091
SHANGHAI
1561, 1681
SHARP
0461, 0471, 0541,
0661, 0911, 0941,
1141
SHOGUN
1031
SIGNATURE 0991, 1771
SIMPSON
0581, 0961
SOLAVOX
1151
SONOKO
1001
SONTEC
SONY
1001
0371, 0451, 0661,
0841, 0951, 1281,
1441
SOUNDESIGN 0861, 0961, 1051,
1091
SOUNDWAVE 1001
SPECTRICON 1161
SQUAREVIEW 0481
SSS
1031, 1051
STAR-LITE
1051
SUPREM
0951
SUPRE-MACY 1131
SURPA
0351, 0971
SYLVANIA
0101, 0361, 0441,
0581, 0591, 0601,
0611, 0631, 0961,
1111
SYMPHONIC 0481
SYSLINE
1001
TANDY
0271, 0431, 1141
TATUNG
0271, 0881, 1001,
1041, 1161
TCL
1561, 1631, 1701
TECHNICS
0751
TECHWOOD 0351, 0751, 0971
TEKNIKA
0101, 0351, 0571,
0931, 0941, 0961,
0971, 0991, 1031,
1051, 1091, 1121,
1131, 1771
TELETECH
0331
TERA
0501
THAKRAL
1671
THORM
1001
TMK
0351, 0861, 0971,
1081
TOSHIBA
0381, 0521, 0621,
0661, 0931, 0981,
1301
TOSONIC
1011
TOTEVISION 0941
TRICAL
0911
UNIVERSAL 0781, 0791
UNIVERSUM 1001
VECTOR RESEARCH
0361, 1111
VESTEL
1001
VICTOR
0651
VIDEO CONCEPT 1101
VIDIKRON
0101, 0211
VIDTECH
0861, 1031
VIKING
1131
WARDS
0101, 0361, 0451,
0541, 0581, 0591,
0601, 0611, 0771,
0781, 0791, 0861,
0971, 0991, 1031,
1091, 1111, 1771
WATSON
1001
XOGEGO
1611, 1621, 1661,
1741, 1761
YAMAHA
0361, 1031, 1111,
1951, 1961, 1971,
1981
YOKO
1001
ZENITH
0011, 0041, 0891,
0991, 1771
ZONDA
1161
CABLE TV
ABC
ANTRONIX
ARCHER
0256, 0376
0136
0136, 0286
BBT
0076
CABLETIME 0166
CABLEVISION
0196
COLOUR VOICE
0306, 0346
COMTRONICS
0216, 0276
EAGLE COMTRONICS
0276
EASTERN
0066
ELECTRICORD
0206
ELECTUS
0266
GE
0116, 0126
GEC CABLE SYSTEM
0196
GENERAL INSTRUMENT
0926, 0936, 0946
HAMLIN H5 0676
HAMLIN H6 0666
HAMLIN H6S 0656
HAMLIN H8 0646
HAMLIN H9 0636
JERROLD
0256
JERROLD 400L
0626
JERROLD 450L
0616
JERROLD 550
0606
JERROLD OSD CATV
0596
JERROLD SPRUCER
0436
MAGNAVOX/PHILIPS
0416, 0426
MAMM
0296
MEMOREX
0386
MOTOROLA 0956, 0966
MOVIE TIME 0146, 0206
NORTHCOAST
0016
NSC
0146
OAK
0106
OAK SIGMA 450
0546
OAK SIGMA 550
0536
PANASONIC TZ 120/130
0476
PANASONIC TZ 170/180
0446
PANASONIC TZ140 0466
PANASONIC TZ150/160
0456
PARAGON
0386
PHILIPS
0036, 0216, 0306,
0316, 0326, 0336,
0346
PIONEER
0006, 0086
PIONEER BR50
0846
PIONEER BR60/70/80/81/82
0696
PIONEER BR90
0556
PULSAR
0386
RCA DIGITAL SATELLITE
SYSTEM
0396, 0406, 0986,
0996, 1006
REALISTIC
0136
REGENCY/EASTERN0686
RUNCO
0386
SAMSUNG
0276
SCIENTIC ATLANTA
0976
SCIENTIFIC ATLANTA 175/475
0576
SCIENTIFIC ATLANTA 75
0366, 0586
SCIENTIFIC ATLANTA 8650
0566
SIGNAL
0276
SL MARX
0276
SPECTAVISION
0236
STANDARD COMPONENTS
0186
STARCOM V 0256
STARGATE
0276
SYLVANIA/TEXSCAN
0376, 0496
TEKNIKA
0176
TELESERVICE
0056
TELEVIEW
0276
TEXSCAN
0186, 0376
TFC
0026
TOCOM
0226, 0356
TOCOM 5503A 0526
TOCOM 5503VIP/5507
0516
TOCOM TC56 0506
TOSHIBA
0386
TUDI
0046
UNIKA
0136
UNIVERSAL 0136, 0156, 0206,
0286
VIDEOWAY
0096
VIEWSTAR
0216
ZENITH
0246, 0386, 0486
SATELLITE TUNER
ALPHA STAR 0826
CHAPARRAL 0756
ECHOSTAR
0836
GENERAL INSTRUMENT
0776, 0876
HTS
0836
HUGHES NETWORK SYSTEMS
0816
JERROLD
0776, 0786
PANASONIC 0806
PRIMESTAR 0776, 0786
RCA
0766
SONY
0796
(DBS)
HITACHI
0856
MAGNAVOX 0886
MEMOREX
0886
PANASONIC 0896
PHILIPS
0886
SONY
0906
STAR CHOICE 0876
TOSHIBA
0866, 0916
UNIDEN
0886
VCR
A TANDY
ADVENTURA
AIKO
AIWA
AKAI
0902
0992
0982
0992
0262, 0942, 0952,
0962, 0972
AMERICAN HIGH 0932
AMSTRAD
0992
ASA
0002, 0912
ASHA
0922
AUDIO DYNAMICS 0202
AUDIOVOX
0912
BEAUMARK 0922
BELL & HOWELL 0902
BLAUPUNKT 0412
BROKSONIC 0872, 0882, 0892
BUSH
0852
CALIX
0912
CANON
0862, 0932
CCE
0852, 0982
CITIZEN
0912, 0982
COLT
0852
CRAIG
0832, 0842, 0852,
0912, 0922
CURTIS MATHES
0662, 0822,
0932
CYBERNEX 0922
DAEWOO
0802, 0812, 0982
DBX
0202
DYNATECH 0472, 0992
ELECTROHOME
0912
ELECTROPHONIC 0912
EMEREX
0792
EMERSON
0072, 0132, 0142,
0152, 0162, 0172,
0182, 0192, 0212,
0702, 0712, 0722,
0732, 0742, 0752,
0762, 0772, 0782,
0872, 0882, 0892,
0912, 0952, 0992,
1072
FINLUX
0002, 0992
FISHER
0682, 0692, 0842,
0902
FUJI
0672, 0932
FUNAI
0992
GARRARD
0992
GE
0662, 0822, 0932
GO VIDEO
0642, 0652
GOODMANS 0402
GRADIENTE 0992
GRANDA
0612, 0902
GRUNDIG
0002
H/K
1082
HARLEY DAVIDSON
0992
HARMAN/KARDON
0632, 1082
HARWOOD
0752, 0852
HEADQUARTER
0612
HI-Q
0842
HINARI
0852
HITACHI
0102, 0562, 0572,
0582, 0592, 0602,
0992
ITT
0942
JVC (VICTOR) 0202, 0522, 0532,
0542, 0552
KENWOOD
0202, 0542, 0612,
0632, 0902
KLH
0852
KODAK
0912, 0932
LG (GOLDSTAR)
0082, 0632,
0912
LLOYD
0992
LOGIK
0852
LUXOR
0942
LXI
0022, 0912
MAGNAVOX 0002, 0482, 0492,
0502, 0512, 0932
MAGNIN
0922
MARANTZ
0002, 0202, 0402,
0632, 0932
MARTA
0912
MATSUSHITA 0932
MATSUI
0722
MEI
0222, 0932
MEMOREX
0232, 0242, 0472,
0512, 0612, 0842,
0902, 0912, 0922,
0932, 0992
MGA
0762, 0952
MGA TECHNOLOGY
0922
MINOLTA
0592, 0602
APPENDIX-ii
MITSUBISHI
0452, 0462, 0542,
0762, 0952, 1082
MOTOROLA 0472, 0932
MTC
0922, 0992
MULTITECH 0852, 0992
NAD
0442
NEC
0122, 0202, 0292,
0422, 0432, 0542,
0632
NIKKO
0912
NOBLEX
0922
OLYMPUS
0412, 0932
OPTIMUS
0442, 0472, 0912
OPTONICA
0402
ORION
0212, 0722, 0742,
0772
OSAKI
0912
PANASONIC 0012, 0052, 0092,
0222, 0372, 0382,
0392, 0412, 0932
PENNY
0202, 0432, 0602,
0632, 0692, 0912,
0922, 0932
PENTAX
0592, 0602
PERDIO
0992
PHILCO
0002, 0932
PHILIPS
0002, 0282, 0402,
0492, 0932
PILOT
0912
PIONEER
0442, 0542
PROSCAN
1002, 1012, 1022,
1032, 1042, 1052,
1062
PULSAR
0512
QUARTER
0612
QUARTZ
0272, 0612
QUASAR
0382, 0392, 0932
RADIO SHACK
0912, 0992
RADIX
0912
RANDEX
0912
RCA
0112, 0382, 0392,
0482, 0592, 0602,
0662, 0822, 0942
REALISTIC
0402, 0472, 0612,
0682, 0842, 0902,
0912, 0922, 0932,
0992
RICOH
0352, 0362
SAISHO
0212, 0582, 0722,
0732, 0742, 0772
SALORA
0612, 0762
SAMSUNG
0212, 0312, 0922,
0962
SANKY
0472, 0512
SANSUI
0292, 0542, 0832
SANYO
0242, 0612, 0842,
0902, 0922
SBR
0002, 0282
SCHEIDER
0852
SCOTT
0342, 0712, 0762,
0872, 0882, 0892
SEARS
0302, 0592, 0602,
0612, 0682, 0692,
0842, 0902, 0912,
0932
SHARP
0402, 0472
SHINTOM
0852
SHOGUN
0922
SINGER
0852
SONY
0032, 0332, 0352,
0362, 0672, 0792,
0932
STS
0602
SUNPAK
0352
APPENDIX-iii
SYLVANIA
0002, 0492, 0502,
0762, 0932, 0992
SYMPHONIC 0992
TANDY
0992
TASHIKO
0712, 0992
TEAC
0992
TECHNICS
0932
TEKNIKA
0322, 0912, 0932,
0992
TELEFUNKEN 0252
TMK
0212, 0732, 0772,
0922
TOSHIBA
0062, 0302, 0342,
0622, 0682, 0712,
0762
TOTEVISION 0912, 0922
UNITECH
0922
VECTOR RESEARCH
0202, 0432, 0632
VIDEO CONCEPTS
0202, 0432, 0632,
0952
WARDS
0322, 0402, 0472,
0482, 0602, 0712,
0842, 0852, 0922,
0932, 0992
YAMAHA
0202, 0632
ZENITH
0042, 0362, 0512,
0672
DVD PLAYER
AKAI
AIWA
DENON
HITACHI
JVC
KENWOOD
LG
MAGNAVOX
MITSUBISHI
ONKYO
PANASONIC
PHILIPS
PIONEER
PROSCAN
RCA
SAMSUNG
SHARP
SONY
TECHNICS
THOMSON
TOSHIBA
YAMAHA
ZENITH
0058
0218
0188
0198
0088, 0178
0148
0228
0128
0138
0068, 0128
0028
0098, 0128
0108, 0118
0158
0158
0078
0038
0018
0028
0168
0048, 0128
0008, 0028, 0098
0128
DVD RECORDER
PANASONIC
PHILIPS
PIONEER
SHARP
SONY
TOSHIBA
YAMAHA
0238, 0248, 0258
0208
0278, 0288, 0298
0338, 0348
0308, 0318, 0328
0268
0208
LD PLAYER
AIWA
0157
DENON
0147
DISCO VISION0017
FUNAI
0157
HITACHI (E) 0017
KENWOOD
0087, 0107
MAGNAVOX 0027
MARANTZ
MITSUBISHI
NAD
PANASONIC
PHILIPS
PIONEER
RCA
REALISTIC
SHARP
SONY
VICTOR
YAMAHA
0027
0137
0137
0077, 0177
0027
0017, 0037, 0137
0167
0157
0127
0047, 0057, 0117
0097
0007, 0067
CD PLAYER
ACOUSTIC RESEARCH
1295
ADC
0025, 0065
ADCOM
0205, 0255, 1015
ADS
0265
AIWA
0295, 0945, 1035,
1055
AKAI
0175, 0485, 0535
ALPINE
1215, 1305
AUDIO-TECHNICA 0545
BSR
0245, 0655, 0775
CALIFORNIA AUDIO LAB
0055
CAPETRONIC 1205
CARRERA
0245
CARVER
0285, 1135
CASIO
0345
CROWN
0185
CURTIS MATHES
0345
DENON
0275, 0875, 0885
DEUAL (E)
0505
DYNAMIC BASS (H)
0555
EMERSON
0205, 0325, 1105
EROICA
1275
FISHER
0095, 0555, 0925,
1005
GARRARD
0365
GENEXXA
0305, 0325, 1105
H/K
0105, 0175, 0465,
0995
HITACHI
0195, 0205, 0505,
0815
INKEL
0115, 0395
JVC
0315
KENWOOD
0045, 0095, 0405,
0585, 0725, 0735,
0745, 0755, 0895
KYOCERA
0025
LG (GOLDSTAR)
1135, 1225,
1265, 1335
LUXMAN
0075, 0425, 0675,
0705, 0715, 0985
MAGNAVOX 0165, 0215, 0645,
0955
MARANTZ
0215, 0235, 0375,
0785, 1345
MCINTOSH
0355, 1085
MCS
0905, 1315
MEMOREX
0205, 0225, 0235,
0305, 0325, 1105
MGA
0135
MISSION
0215
MITSUBISHI 0135, 0445
MTC
1255
NAD
0035, 0615, 0685,
0695
NAKAMICHI 0125, 0435, 0515
NEC
0255, 0905, 0965
NIKKO
0545, 1005
ONKYO
0155, 0455, 0495,
0805, 1155
OPTIMUS
0225, 0245, 0555,
0595, 0845, 0855,
0865, 0895, 0935
PANASONIC 0055, 0825, 1095,
1125
PENNY
0905
PHILIPS
0165, 0215
PIONEER
0305, 0935, 1045
PROTON
0215, 1185
QUASAR
0055
RCA
0205, 0915, 1115
REALISTIC
0205, 0225, 0235,
0325, 0555, 0845
REVOX
1175
ROTEL
0215
SABA TELECOMMANDER (E)
0505
SAE
0215
SAMSUNG
1285
SANSUI
0215, 0625, 0975,
1025, 1105
SANYO
0145, 0555, 0635,
0765
SCOTT
0325, 1105
SEARS
0345
SHARP
0235, 0665, 0895,
1065, 1075
SHERWOOD 0115, 0235, 0395,
0475
SIEMENTS GARRARD
1245
SIGNATURE 0175
SONTEC
1165
SONY
0065, 0565, 0865,
1145
STARON
1235
STS
0025
SYLVANIA
0215
SYMPHONIC 0335
TANDY
0305
TANGBERG 1195
TEAC
0235, 0335, 0385,
0525, 0795, 0835,
1355
TECHNICS
0055, 0605, 1095
TECHWOOD 1325
TELEFUNKEN (E) 0505
THOMSON (E) 0505
TOSHIBA
0035, 0685
VECTOR RESEARCH
0065, 1135
VICTOR
0315
WARDS
0175
YAMAHA
0005, 0015, 0085,
0415, 0545, 0575,
1065
CD RECORDER
HITACHI
JVC
MARANTZ
PHILIPS
PIONEER
YAMAHA
0474
0504
0484, 0494
0444
0454, 0464
0414
01EN_RX-V457_U.book Page i Tuesday, May 31, 2005 2:48 PM
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
10
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1
2
3
4
5
6
7
8
9
i
11
Read Instructions – All the safety and operating instructions
should be read before the product is operated.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions – All operating and use instructions
should be followed.
Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to
overturn.
12
13
14
15
16
17
18
19
Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
01EN_RX-V457_U-cv.fm Page 1 Thursday, May 19, 2005 10:24 AM
U
RX-V457
AV Receiver
© 2005
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WE59830-1
Download PDF
Similar pages
CR 12 McIntosh
P42W22B_New Style.qxd
DVD specs 7/03
Circular LED Clock
MX 134 McIntosh
Sharp Htsb600 Quick Specs
MX 119 McIntosh
MHT 200 McIntosh
TRUCKLOAD SALE 46" Diagonal »1 •1
RX-V2300