Allied Telesis AT-FS705LE Installation guide

AT-FS705LE
10/100Base Ethernet Switch
Installation Guide
PN 613-50138-00 Rev C
Copyright  2002 Allied Telesyn, Inc.
960 Stewart Drive Suite B, Sunnyvale CA USA 94086
All rights reserved. No part of this publication may be
reproduced without prior written permission from Allied
Telesyn, Inc.
Ethernet is a registered trademark of Xerox Corporation. All
other product names, company names, logos or other
designations mentioned herein are trademarks or registered
trademarks of their respective owners.
Allied Telesyn, Inc. reserves the right to make changes in
specifications and other information contained in this
document without prior written notice. The information
provided herein is subject to change without notice. In no
event shall Allied Telesyn, Inc. be liable for any incidental,
special, indirect, or consequential damages whatsoever,
including but not limited to lost profits, arising out of or
related to this manual or the information contained herein,
even if Allied Telesyn, Inc. has been advised of, known, or
should have known, the possibility of such damages.
Electrical Safety and Emission
Statement
Standards: This product meets the following standards.
U.S. Federal Communications Commission
Declaration Of Conformity
Manufacture Name:
Allied Telesyn, Inc.
Manufacture Address:
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
Manufacture Telephone:
408-730-0950
Declares that the product:
Ethernet Switch
Model Number:
AT-FS705LE
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device must not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Radiated Energy
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device pursuant to Part
15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with instructions, may cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on. The user is
encouraged to try to correct the interference by one or more
of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the
receiver.
iii
-
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician
for help.
Changes and modifications not expressly approved by the
manufacturer or registrant of this equipment can void your
authority to operate this equipment under Federal
Communications Commission rules.
Industry Canada
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
RFI Emission
EN55022 Class B
$
1
Warning: In a domestic environment this product
may cause radio interference in which case the
user may be required to take adequate measures.
2
$
$
Immunity
EN50082-1
Electrical Safety
UL 1950, EN60950, VCCI
4
Class B
$
3
Important: Appendix A contains translated safety
statements for installing this equipment. When you see the
, go to Appendix A for the translated safety statement in
your language.
$
$
Wichtig: Anhang A enthält übersetzte Sicherheitshinweise
für die Installation dieses Geräts. Wenn Sie
sehen,
schlagen Sie in Anhang A den übersetzten Sicherheitshinweis
in Ihrer Sprache nach.
Vigtigt: Tillæg A indeholder oversatte sikkerhedsadvarsler,
der vedrører installation af dette udstyr. Når De ser symbolet
, skal De slå op i tillæg A og finde de oversatte
sikkerhedsadvarsler i Deres eget sprog.
$
iv
Belangrijk: Appendix A bevat vertaalde
veiligheidsopmerkingen voor het installeren van deze
ziet, raadpleeg Appendix A
apparatuur. Wanneer u de
voor vertaalde veiligheidsinstructies in uw taal.
$
Important: L'annexe A contient les instructions de sécurité
relatives à l'installation de cet équipement. Lorsque vous
, reportez-vous à l'annexe A pour
voyez le symbole
consulter la traduction de ces instructions dans votre langue.
$
$
Tärkeää: Liite A sisältää tämän laitteen asentamiseen
-symbolin, katso
liittyvät käännetyt turvaohjeet. Kun näet
käännettyä turvaohjetta liitteestä A.
Importante: l’Appendice A contiene avvisi di sicurezza
tradotti per l’installazione di questa apparecchiatura. Il
, indica di consultare l’Appendice A per l’avviso di
simbolo
sicurezza nella propria lingua.
$
$
Viktig: Tillegg A inneholder oversatt sikkerhetsinformasjon
, åpner du til
for installering av dette utstyret. Når du ser
Tillegg A for å finne den oversatte sikkerhetsinformasjonen
på ønsket språk.
Importante: O Anexo A contém advertências de segurança
traduzidas para instalar este equipamento. Quando vir o
, leia a advertência de segurança traduzida no seu
símbolo
idioma no Anexo A.
$
Importante: El Apéndice A contiene mensajes de seguridad
traducidos para la instalación de este equipo. Cuando vea el
símbolo
, vaya al Apéndice A para ver el mensaje de
seguridad traducido a su idioma.
$
$
Obs! Bilaga A innehåller översatta säkerhetsmeddelanden
avseende installationen av denna utrustning. När du ser
,
skall du gå till Bilaga A för att läsa det översatta
säkerhetsmeddelandet på ditt språk.
v
Table of Contents
Electrical Safety and
Emission Statement ................................. iii
Welcome to Allied Telesyn ........................ ix
Where to Find Web-based Guides ................. ix
Document Conventions .................................. ix
Contacting Allied Telesyn
Technical Support .........................................x
Online Support .........................................x
Telephone Support .................................. xi
E-mail Support ........................................ xi
Returning Products ........................................xii
FTP Server..................................................... xiii
For Sales or Corporate Information ............. xiii
Tell Us What You Think ............................... xiii
AT-FS705LE Fast Ethernet Switch ..........1
Overview ..........................................................1
Features ...........................................................2
Physical Description........................................3
Ports 1 Through 4.....................................3
Port 5 and the Uplink Port ......................4
Status LEDs .............................................5
Power Supply............................................6
vii
Network Topologies .........................................6
Installing the Switch .......................................8
Verifying the Package Contents ..............8
Selecting a Site .........................................9
Reviewing Safety Guidelines ..................10
Installing the Switch on a Desktop ........12
Installing the Switch on a Wall ..............14
Warranty Registration ...................................16
Troubleshooting ..............................................16
Technical Specifications .................................18
Physical....................................................18
Temperature ............................................18
Electrical Rating......................................18
Agency Compliance .................................18
Translated Safety and Emission
Information ..................................................19
viii
Welcome to Allied Telesyn
This guide contains instructions on how to
install the AT-FS705LE Ethernet Switch.
Where to Find Web-based Guides
The Allied Telesyn web site at
www.alliedtelesyn.com offers you an easy
way to access the most recent documentation,
software, and technical information for all of
our products. For product guides, select
“Support & Services” from our web site.
Document Conventions
This guide uses the following conventions:
Note
A note provides additional information.
ix
Caution
Cautions informs you that performing or
omitting a specific action may result in
equipment damage or loss of data.
Warning
Warnings informs you that performing or
omitting a specific action may result in
bodily injury.
Contacting Allied Telesyn Technical Support
You can contact Allied Telesyn technical
support online or by telephone or e-mail.
Online Support
You can request technical support online by
accessing the Knowledge Base at
kb.alliedtelesyn.com. You can use the
Knowledge Base to submit questions to our
technical support staff and review answers to
previously asked questions.
x
AT-FS705LE Installation Guide
Telephone Support
For technical support by phone, contact Allied
Telesyn at one of the following locations:
Americas
United States, Canada,
Mexico, Central America,
South America
Tel: 1 (800) 428-4835
Germany
Switzerland, Austria, Eastern
Europe
Tel: (+49) 30-435-900-126
Asia
Singapore, Taiwan, Thailand,
Malaysia, Indonesia, Korea,
Philippines, China,
India, Hong Kong
Tel: (+65) 3815-612
Italy
Spain, Portugal, Greece,
Turkey, Israel
Tel: (+39) 02-41-30-41
Australia
Tel:
1 (800) 000-880
Japan
Tel: (+81) 3-3443-5640
France
Belgium, Luxembourg, The
Netherlands, Middle East,
Africa
Tel: (+33) 0-1-60-92-15-25
United Kingdom
Denmark, Norway, Sweden,
Finland, Iceland
Tel: (+0044) 1235-442500
E-mail Support
Latin America, Mexico, Puerto Rico,
Caribbean, and Virgin Islands
latin_america@alliedtelesyn.com
Europe
support_europe@alliedtelesyn.com
xi
Returning Products
Products for return or repair must first be
assigned a Return Materials Authorization
(RMA) number. A product sent to Allied
Telesyn without a RMA number will be
returned to the sender at the sender’s expense.
To obtain an RMA number, contact Allied
Telesyn’s Technical Support at one of the
following locations:
North America
Toll-free: 1-800-762-1664
Fax: 1-425-806-1050
Europe, Africa, and the
Middle East
Tel: +44-1793-501401
Fax: +44-1793-431099
Latin America, the
Caribbean,
Virgin Islands
Tel: international code +
425-481-3852
Fax: international code +
425-481-3895
Puerto Rico
Tel: 1-800-424-5012, ext 3852
or
1-800-424-4284, ext 3852
Mexico
Toll-free: 800-424-5012, ext
3852
Fax: international code +
425-482-3895
Asia and Southeast Asia
Tel: +65-381-5612
Fax: +65-383-3830
Australia
Toll-free: 1-800-000-880
Fax: +61-2-9438-4966
New Zealand
Toll-free: 0800-45-5782
xii
AT-FS705LE Installation Guide
FTP Server
If you need management software for an Allied
Telesyn managed device and you know the file
name of the software, you can download the
software by connecting directly to our FTP
server at ftp:alliedtelesyn.com. At login,
enter ‘anonymous’ for the user name and your
e-mail address for the password.
For Sales or Corporate Information
You can contact Allied Telesyn for sales or
corporate information at the location below:
Allied Telesyn, Inc.
19800 North Creek Parkway, Suite 200
Bothell, WA 98011
Tel: 1 (425) 487-8880
Fax: 1 (425) 489-9191
Tell Us What You Think
If you have any comments or suggestions on
how we might improve this or other Allied
Telesyn documents, please fill out the General
Enquiry Form online. This form can be accessed
by selecting “Contact Us” from
www.alliedtelesyn.com.
xiii
AT-FS705LE Fast Ethernet
Switch
Overview
The AT-FS705LE Ethernet Switch is a
10Base-T/100Base-TX unmanaged switch. The
switch provides you with a simple, cost-effective
solution for Ethernet switching between endnodes operating at either 10 Mbps or 100 Mbps.
Figure 1 and Figure 2 show the front and back
panels of the switch.
Port LEDs
DC Power Connector
Figure 1 AT-FS705LE Front Panel
1
Figure 2 AT-FS705LE Back Panel
Features
The AT-FS705LE switch has the following
features:
❑ Five auto-negotiating 10/100 Mbps
twisted pair ports with RJ-45 connectors
❑ One Uplink port for connecting the
AT-FS705LE switch to another switch or
hub without a crossover cable
❑ IEEE 802.3 and IEEE 802.3u compliant
❑ External AC/DC power adapter
❑ Small compact size for use on a desktop or
wall-mountable
2
AT-FS705LE Installation Guide
Physical Description
The physical description for the switch
includes:
❑ Ports 1 through 4
❑ Port 5 and the Uplink port
❑ LEDs
❑ Power supply
Ports 1 Through 4
Ports 1 through 4 can operate at either 10 Mbps
or 100 Mbps and in either half- or full-duplex
mode. The ports, featuring RJ-45 connectors,
are configured as MDI-X, meaning that you can
connect a workstation or server to one of the
ports without using a crossover cable. The ports
have a maximum operating distance of 100
meters (328 feet) using Category 5 cable.
The ports are IEEE 802.3u auto-negotiation
compliant. This means that the ports can
automatically configure their speed and duplex
mode to match the capabilities of the end-nodes
connected to the ports.
3
Port 5 and the Uplink Port
Port 5 and the Uplink port allow you to connect
an additional workstation to the switch or
interconnect the switch with another switch or
hub, without the use of a crossover cable. If you
need to connect an additional workstation to
the switch, use Port 5, which is configured as
MDI-X. If you need to connect the switch to
another Ethernet switch, use the Uplink port,
which is configured as MDI.
Both Port 5 and the Uplink port offer 10 Mbps
or 100 Mbps performance and auto-negotiation
operation for both speed and duplex mode. Both
ports feature a RJ-45 connector and have a
maximum operating distance of 100 meters
(328 feet) using Category 5 cable.
Note
You can use either Port 5 or the Uplink
port, but you cannot use both
simultaneously.
4
AT-FS705LE Installation Guide
Status LEDs
Refer to Table 1 for a description of the switch’s
LEDs.
Table 1 LEDs
LEDs
Color
Description
PWR
Green
Power is applied to the
switch.
100M
Green
The port is operating at 100
Mbps.
OFF
The port is operating at 10
Mbps.
Green
A valid link has been
established on the port.
Flashing
Data is being transmitted or
received on the port.
Green
The port is operating in
full-duplex mode.
OFF
The port is operating in
half-duplex mode.
LINK/ACT
FDX
5
Power Supply
The AT-FS705LE switch uses an external AC/
DC power adapter that comes standard with
the switch.
Network Topologies
Figure 3 illustrates a network that consists of
one AT-FS705LE switch used to interconnect
four workstations and a server. In this
configuration, the Uplink port is not used.
Figure 3 Single AT-FS705LE Switch Topology
6
AT-FS705LE Installation Guide
Figure 4 illustrates a network of two
AT-FS705LE switches that have been
interconnected using the Uplink ports on the
two units. Using the Uplink ports eliminates
the need for a crossover cable to interconnect
the switches.
Figure 4 Multiple AT-FS705LE Switch Topology
7
Installing the Switch
This section contains the procedures for
installing the switch.
Verifying the Package Contents
Make sure the following items are included in
your package. If any item is missing or
damaged, contact your Allied Telesyn sales
representative for assistance.
❑ An AT-FS705LE Ethernet Switch
❑ An external power adapter
❑ Four self-adhesive rubber feet
❑ This installation guide
❑ Warranty card
Note
For wall-mount installation, the screws,
plastic anchors, and any other material
necessary to physically mount the switch
to the wall are not provided.
8
AT-FS705LE Installation Guide
Selecting a Site
Be sure to observe the following requirements
when choosing a site for your switch.
❑ Make sure you are placing the switch in a
dust-free and moisture-free environment.
❑ Do not block the ventilation openings on
the unit. Allow at least 10 centimeters (4
inches) of space at the front and back of
the unit for ventilation.
❑ Make sure that the switch’s power is
accessible and cables can be connected
easily.
❑ Cabling should be away from sources of
electrical noise such as radios,
transmitters, broadband amplifiers,
power lines, and fluorescent fixtures.
❑ Do not place objects on top of the switch.
❑ Use dedicated power circuits or power
conditioners to supply power to the
switch.
9
❑ Observe the following cabling
specifications:
Ports
Connector
Type
Type of
Cable
Maximum
Distance
1 through 5
RJ-45
Category 5
100 m
(328 ft)
Uplink
RJ-45
Category 5
100 m
(328 ft)
Reviewing Safety Guidelines
Please review the following safety guidelines
before installing the switch.
Warning
Power cord is used as a disconnection
device. To de-energize equipment,
disconnect the power cord. $ 5
Caution
Pluggable Equipment: The socket
outlet should be installed near the
equipment and should be easily
accessible. $ 6
10
AT-FS705LE Installation Guide
Caution
Air vents: The air vents must not be
blocked on the unit and must have free
access to the room ambient air for cooling.
$7
Caution
Operating Temperature: This product
is designed for a maximum ambient
temperature of 40°C. $ 8
Caution
All Countries: Install this product in
accordance with local and National
Electric Codes. $ 9
Caution
Europe - EU: Use TÜV licensed AC
adapter of DC 7.5V, 1A. $ 10
Caution
USA/Canada: Use a UL Listed/CSA
Certified AC adapter of DC 7.5V, 1A.
$ 11
11
Installing the Switch on a Desktop
To use the switch on the desktop, perform the
following procedure. To wall-mount the switch,
refer to “Installing the Switch on a Wall” on
page 14.
1. Remove all the items from the shipping
package and store the packaging material in
a safe place.
2. Attach the four self-adhesive rubber feet to
the bottom of the switch, positioning them in
the indentations.
3. Place the switch on a flat, level surface.
Warning
The power cord is used as a
disconnection device. To de-energize
equipment, disconnect the power cord.
$5
4. Plug the AC/DC power adapter into an
appropriate AC power outlet and insert the
power plug into the DC receptacle located on
the front of the switch.
5. Make sure the PWR LED, is green. If the
LED is OFF, refer to “Troubleshooting” on
page 16.
12
AT-FS705LE Installation Guide
6. Attach the data cables to the switch ports. Do
not use a crossover cable to connect
workstations or servers to ports 1 through 5.
Do not use a crossover cable to connect
another switch or hub to the Uplink port.
Note
You can use either Port 5 or the Uplink
port, but you cannot use both
simultaneously.
7. Power ON the end-nodes.
8. Check that the LINK/ACT LEDs for each port
on the switch are green. If the LEDs are OFF,
refer to “Troubleshooting” on page 16 for
instructions.
The switch is now ready for use.
13
Installing the Switch on a Wall
For wall-mount installation, you can position
the switch vertically or horizontally using the
keyhole cutouts in the bottom of the switch.
1. If previously attached, remove the rubber
feet, data cables, and the DC power cord from
the switch.
2. Select a wall location for the switch.
Note
For wall-mount installation, the screws,
plastic anchors, and any other material
necessary to physically mount the switch
to the wall are not provided.
3. Install two plastic anchors and two pan-head
screws into the wall, separated by 5
centimeters (approximately 2 inches).
4. Position the switch onto the wall screws.
Warning
The power cord is used as a
disconnection device. To de-energize
equipment, disconnect the power cord.
$5
14
AT-FS705LE Installation Guide
5. Plug the AC/DC power adapter into an
appropriate AC power outlet and insert the
power plug into the DC receptacle located on
the front of the switch.
6. Make sure the PWR LED, is green. If the
LED is OFF, refer to “Troubleshooting” on
page 16.
7. Attach the data cables to the switch ports. Do
not use a crossover cable to connect
workstations or servers to ports 1 through 5.
Do not use a crossover cable to connect
another AT-FS705LE switch to the Uplink
port.
Note
You can use either Port 5 or the Uplink
port, but you cannot use both
simultaneously.
8. Power ON the end-nodes.
9. Check that the LINK/ACT LEDs for each port
on the switch are green. If the LEDs are OFF,
refer to “Troubleshooting” on page 16 for
instructions.
The switch is now ready for use.
15
Warranty Registration
When you have finished installing the product,
register your product by completing the
enclosed warranty card and sending it in. You
can also fill out the registration online by
selecting “Warranties” under “Support &
Services” from www.alliedtelesyn.com.
Troubleshooting
Follow the guidelines below to test and
troubleshoot the installation in the event a
problem occurs.
If the PWR LED is OFF, do the following:
❑ Check to be sure that the power adapter is
securely connected to the power source
and to the DC connector on the front of the
AT-FS705LE switch.
❑ Check to be sure that the power outlet has
power by connecting another device to it.
❑ Try replacing the power adapter with
another power adapter.
16
AT-FS705LE Installation Guide
If the LINK/ACT LED is OFF, do the following:
❑ Check to be sure that the end-node
connected to the port on the switch is
powered ON. If the end-node is OFF,
power the unit ON.
❑ Check that the cable is securely connected
to the port on the switch and on the endnode.
❑ Check to be sure that the distance
between the switch and the end-node does
not exceed 100 meters (328 feet).
❑ Check to be sure that you are using
Category 5 cable.
❑ Check to be sure that the cable has not
been cut or damaged.
If there is a communication problem between
the end-nodes connected to the switch, do the
following:
❑ Verify that the switch and end-nodes are
operating with the same duplex mode.
If you are still experiencing problems after
testing and troubleshooting the installation,
refer to “Contacting Allied Telesyn Technical
Support” on page x or visit our web site at
www.alliedtelesyn.com for support
information.
17
Technical Specifications
Physical
Dimensions:
WxDxH
100 x 78.5 x 26 mm
(3.93 x 3.09 x 1.02 in)
Temperature
Maximum Operating
0° to 40° C
Maximum Storage
-25° to 70° C
Operating Humidity
10% to 90% Relative
Humidity
Electrical Rating
Input Supply Voltage:
7.5V @ 1A
Power Consumption:
4W
Agency Compliance
Standards
Compatibility:
Electromagnetic
Emission:
18
IEEE 802.3
IEEE802.3u
FCC Class B
CE Class B
VCCI Class B
Appendix A
Translated Safety and
Emission Information
Important: This appendix contains multiplelanguage translations for the safety statements
in this guide.
Wichtig: Dieser Anhang enthält
Übersetzungen der in diesem Handbuch
enthaltenen Sicherheitshinweise in mehreren
Sprachen.
Vigtigt: Dette tillæg indeholder oversættelser i
flere sprog af sikkerhedsadvarslerne i denne
håndbog.
Belangrijk: Deze appendix bevat vertalingen
in meerdere talen van de
veiligheidsopmerkingen in deze gids.
Important: Cette annexe contient la traduction
en plusieurs langues des instructions de
sécurité figurant dans ce guide.
Tärkeää: Tämä liite sisältää tässä oppaassa
esiintyvät turvaohjeet usealla kielellä.
19
Importante: questa appendice contiene
traduzioni in più lingue degli avvisi di sicurezza
di questa guida.
Viktig: Dette tillegget inneholder oversettelser
til flere språk av sikkerhetsinformasjonen i
denne veiledningen.
Importante: Este anexo contém traduções em
vários idiomas das advertências de segurança
neste guia.
Importante: Este apéndice contiene
traducciones en múltiples idiomas de los
mensajes de seguridad incluidos en esta guía.
Obs! Denna bilaga innehåller flerspråkiga
översättningar av säkerhetsmeddelandena i
denna handledning.
20
AT-FS705LE Installation Guide
Standards: This product meets the following standards:
U.S. Federal Communications Commission
Declaration Of Conformity
Manufacture Name:
Allied Telesyn, Inc.
Manufacture Address:
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
Manufacture Telephone:
408-730-0950
Declares that the product:
Ethernet Switch
Model Number:
AT-FS705LE
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device must not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Radiated Energy
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device pursuant to Part
15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with instructions, may cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on. The user is
encouraged to try to correct the interference by one or more
of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the
receiver.
-
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician
for help.
21
Changes and modifications not expressly approved by the
manufacturer or registrant of this equipment can void your
authority to operate this equipment under Federal
Communications Commission rules.
Industry Canada
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
$
$
$
$
$
$
$
$
$
$
22
1
RFI Emissions
2
Warning: In a domestic environment this product
may cause radio interference in which case the
user may be required to take adequate measures.
3
Immunity
EN50082-1 1997
4
Electrical Safety
UL 1950, EN60950,
VCCI Class B
EN55022 Class B
Safety
5
Caution: Power cord is used as a disconnection
device. To de-energize equipment, disconnect the
power cord.
6
Pluggable Equipment, the socket outlet shall be
installed near the equipment and shall be easily
accessible.
7
Caution: Air vents must not be blocked and must
have free access to the room ambient air for
cooling.
8
Operating Temperature: This product is
designed for a maximum ambient temperature of
40° degrees C.
9
All Countries: Install product in accordance with
local and National Electrical Codes.
10
Europe - EU: Use TÜV licensed AC adapter of DC
7.5V, 1A.
$
AT-FS705LE Installation Guide
11
USA/Canada: Use a UL Listed/CSA Certified AC
adapter of DC 7.5V, 1A.
Normen: Dieses Produkt erfüllt die
Anforderungen der nachfolgenden Normen.
$
$
1
Hochfrequenzstörung
2
$
$
Warnung: Bei Verwendung zu Hause kann
dieses Produkt Funkstörungen hervorrufen. In
diesem Fall müßte der Anwender angemessene
Gegenmaßnahmen ergreifen.
3
Störsicherheit
EN50082-1 1997
4
Elektrische Sicherheit
UL 1950, EN60950,
VCCI Class B
$
$
$
$
$
$
EN55022 Klasse B
Sicherheit
5
Vorsicht: Das netzkabel dient zum trennen der
stromversorgung. Zur trennung vom netz, kabel
aus der steckdose ziehen.
6
Steckbares Gerät: Die Anschlußbuchse sollte in
der Nähe der Einrichtung angebracht werden und
leicht zugänglich sein."
7
Vorsicht: Die Entlüftungsöffnungen dürfen nicht
versperrt sein und müssen zum Kühlen freien
Zugang zur Raumluft haben.
8
Betriebstemperatur: Dieses Produkt wurde für
den Betrieb in einer Umgebungstemperatur von
nicht mehr als 40° C entworfen.
9
Alle Länder: Installation muß örtlichen und
nationalen elektrischen Vorschriften entsprechen.
10
Gebrauchen Sie einen von TÜV zugelassenen
Wechselstromadapter für Gleichstrom 7,5 V, 1A.
23
$
$
$
$
$
$
$
$
$
$
24
Standarder: Dette produkt tilfredsstiller de
følgende standarder.
1
Radiofrekvens forstyrrelsesemission: EN55022
Klasse B
2
Advarsel: I et hjemligt miljø kunne dette produkt
forårsage radio forstyrrelse. Bliver det tilfældet,
påkræves brugeren muligvis at tage
tilstrækkelige foranstaltninger.
3
Immunitet
EN50082-1 1997
4
Elektrisk sikkerhed
UL 1950, EN60950,
VCCI Class B
Sikkerhed
5
Advarsel: Den strømførende ledning bruges til at
afbryde strømmen. Skal strømmen til apparatet
afbrydes, tages ledningen ud af stikket.
6
Udstyr Til Stikkontakt, stikkontakten bør
installeres nær ved udstyret og skal være
lettilgængelig.
7
Advarsel: Ventilationsåbninger må ikke blokeres
og skal have fri adgang til den omgivende luft i
rummet for afkøling.
8
Betjeningstemperatur: Dette apparat er
konstrueret til en omgivende temperatur på
maksimum 40 grader C.
9
Alle Lande: Installation af produktet skal ske i
overensstemmelse med lokal og national
lovgivning for elektriske installationer.
10
Brug kun TÜV godkendt
vekselstrømstransformator på 7.5 V jævnstrøm,
1A.
AT-FS705LE Installation Guide
Eisen: Dit product voldoet aan de volgende eisen.
$
$
1
RFI Emissie
2
$
$
Waarschuwing: Binnenshuis kan dit product
radiostoring veroorzaken, in welk geval de
gebruiker verplicht kan worden om gepaste
maatregelen te nemen.
3
Immuniteit
4
Electrische Veiligheid
$
$
$
$
$
$
EN55022 Klasse B
EN50082-1 1997
UL 1950, EN60950,
VCCI Class B
Veiligheid
5
Waarschuwing: Het toestel wordt uitgeschakeld
door de stroomkabel te ontkoppelen.Om het
toestel stroomloos te maken: de stroomkabel
ontkoppelen.
6
Aan Te Sluiten Apparatuur, de contactdoos wordt
in de nabijheid van de apparatuur geïnstalleerd
en is gemakkelijk te bereiken."
7
Opgelet: De ventilatiegaten mogen niet worden
gesperd en moeten de omgevingslucht
ongehinderd toelaten voor afkoeling.
8
Bedrijfstemperatuur: De
omgevingstemperatuur voor dit produkt mag niet
meer bedragen dan 40 graden Celsius.
9
Alle LandeN: het toestel installeren
overeenkomstig de lokale en nationale elektrische
voorschriften.
10
Gebruik een door TÜV gekeurde
wisselstroomadapter van 7,5 Volt gelijkstroom, 1
ampères.
25
$
$
$
$
$
$
$
$
$
$
26
Normes: ce produit est conforme aux normes de
suivantes.
1
Emission d’interférences
radioélectriques
EN55022 Classe B
2
Mise En Garde: Dans un environnement
domestique, ce produit peut provoquer des
interférences radioélectriques. Auquel cas,
l’utilisateur devra prendre les mesures adéquates.
3
Immunité
EN50082 - 1 1997
4
Sécurité électrique
UL 1950, EN60950,
VCCI Class B
5
Danger De Foudre
Danger: Ne pas manier le matériel ou les câbles
lors d’activité orageuse.
6
Equipement Pour Branchement Electrique, la
prise de sortie doit être placée près de
l’équipement et facilement accessible".
7
Attention: Ne pas bloquer les fentes d’aération,
ceci empêcherait l’air ambiant de circuler
librement pour le refroidissement.
8
Température De Fonctionnement: Ce
matériel est capable de tolérer une température
ambiante maximum de ou 40 degrés Celsius.
9
Pour Tous Pays: Installer le matériel
conformément aux normes électriques nationales
et locales.
10
Utiliser un adaptateur secteur conforme TÜV de
7,5 V, 1 A en courant continu.
AT-FS705LE Installation Guide
Standardit: Tämä tuote on seuraavien
standardien mukainen.
$
$
1
Radioaaltojen häirintä
2
$
$
Varoitus: Kotiolosuhteissa tämä laite voi
aiheuttaa radioaaltojen häiröitä, missä
tapauksessa laitteen käyttäjän on mahdollisesti
ryhdyttävä tarpeellisiin toimenpiteisiin.
3
Kestävyys
EN50082-1 1997
4
Sähköturvallisuus
UL 1950, EN60950,
VCCI Class B
$
$
$
$
$
$
EN55022 Luokka B
Turvallisuus
5
Huomautus: Virtajohtoa käytetään
virrankatkaisulaitteena. Virta katkaistaan
irrottamalla virtajohto.
6
Pistorasiaan Kytkettävä Laite; pistorasia on
asennettava laitteen lähelle ja siihen on oltava
esteetön pääsy."
7
Huomautus: Ilmavaihtoreikiä ei pidä tukkia ja
niillä täytyy olla vapaa yhteys ympäröivään
huoneilmaan, jotta ilmanvaihto tapahtuisi.
8
Käyttölämpötila: Tämä tuote on suunniteltu
ympäröivän ilman maksimilämpötilalle 40°C.
9
Kaikki Maat: Asenna tuote paikallisten ja
kansallisten sähköturvallisuusmääräysten
mukaisesti.
10
Käytä TÜV-lisenssillä valmistettua
verkkosovitinta, jonka tasajännitteen
nimellisarvot ovat DC 7,5 V, 1 A (ampeeria).
27
$
$
$
$
$
$
$
$
$
$
28
Standard: Questo prodotto è conforme ai
seguenti standard.
1
Emissione RFI
(interferenza di
radiofrequenza)
EN55022 Classe B
2
Avvertenza: in ambiente domestico questo
prodotto potrebbe causare radio interferenza. In
questo caso potrebbe richiedersi all’utente di
prendere gli adeguati provvedimenti.
3
Immunità
EN50082-1 1997
4
Sicurezza elettrica
UL 1950, EN60950,
VCCI Class B
Norme Di Sicurezza
5
Attenzione: Il cavo di alimentazione è usato
come dispositivo di disattivazione. Per togliere la
corrente al dispositivo staccare il cavo di
alimentazione.
6
Apparecchiatura Collegabile, la presa va
installata vicino all’apparecchio per risultare
facilmente accessibile".
7
Attenzione: le prese d’aria non vanno ostruite e
devono consentire il libero ricircolo dell’aria
ambiente per il raffreddamento.
8
Temperatura Di Funzionamento: Questo
prodotto è concepito per una temperatura
ambientale massima di 40 gradi centigradi.
9
Tutti I Paesi: installare il prodotto in conformità
delle vigenti normative elettriche nazionali.
10
Utilizzare l’adattatore per c.a. da 7,5 V c.c. e 1 A
conforme alla normativa TÜV.
AT-FS705LE Installation Guide
Sikkerhetsnormer: Dette produktet
tilfredsstiller følgende sikkerhetsnormer.
$
$
1
RFI stråling
2
$
$
Advarsel: Hvis dette produktet benyttes til
privat bruk, kan produktet forårsake
radioforstyrrelse. Hvis dette skjer, må brukeren
ta de nødvendige forholdsregler.
3
Immunitet
EN50082-1 1997
4
Elektrisk sikkerhet
UL 1950, EN60950,
VCCI Class B
$
$
$
$
$
$
EN55022 Klasse B
Sikkerhet
5
Forsiktig: Strømledningen brukes til å frakoble
utstyret. For å deaktivisere utstyret, må
strømforsyningen kobles fra.
6
Utstyr For Stikkontakt. Stikkontakten skal
monteres i nærheten av utstyret og skal være lett
tilgjengelig."
7
Forsiktig: Lufteventilene må ikke blokkeres, og
må ha fri tilgang til luft med romtemperatur for
avkjøling.
8
Driftstemperatur: Dette produktet er
konstruert for bruk i maksimum romtemperatur
på 40 grader celsius.
9
Alle Land: Produktet må installeres i samsvar
med de lokale og nasjonale elektriske koder.
10
Benytt TÜV-godkjent AC-adapter på 7,5V DC, 1A
(milliampere).
29
$
$
$
$
$
$
$
$
$
$
30
Padrões: Este produto atende aos seguintes
padrões.
1
Emissão de
interferência de
radiofrequência
EN55022 Classe B
2
Aviso: Num ambiente doméstico este produto
pode causar interferência na radiorrecepção e,
neste caso, pode ser necessário que o utente tome
as medidas adequadas.
3
Imunidade
EN50082-1 1997
4
Segurança Eléctrica
UL 1950, EN60950,
VCCI Class B
Segurança
5
Cuidado: O cabo de alimentação é utilizado como
um dispositivo de desconexão. Para deseletrificar
o equipamento, desconecte o cabo de alimentação.
6
Equipamento De Ligação, a tomada eléctrica deve
estar instalada perto do equipamento e ser de fácil
acesso."
7
Cuidado: As aberturas de ventilação não devem
ser bloqueadas e devem ter acesso livre ao ar
ambiente para arrefecimento adequado do
aparelho.
8
Temperatura De FuncionamentO: Este
produto foi projetado para uma temperatura
ambiente máxima de 40 graus centígrados.
9
Todos Os Países: Instale o produto de acordo
com as normas nacionais e locais para instalações
elétricas.
10
Use um adaptador de corrente alternada com
saída DC de 7,5V e 1A em conformidade com as
especificações da TÜV.
AT-FS705LE Installation Guide
Estándares: Este producto cumple con los
siguientes estándares.
$
$
1
Emisión RFI
2
$
$
Advertencia: en un entorno doméstico, este
producto puede causar radiointerferencias, en
cuyo caso, puede requerirse del usuario que tome
las medidas que sean convenientes al respecto.
3
Inmunidad
EN50082-1 1997
4
Seguridad eléctrica
UL 1950, EN60950,
VCCI Class B
$
$
$
$
$
$
EN55022 Clase B
Seguridad
5
Atencion: El cable de alimentacion se usa como
un dispositivo de desconexion. Para desactivar el
equipo, desconecte el cable de alimentación.
6
Equipo Conectable, el tomacorriente se debe
instalar cerca del equipo, en un lugar con acceso
fácil".
7
Atencion: Las aberturas para ventilación no
deberán bloquearse y deberán tener acceso libre al
aire ambiental de la sala para su enfriamiento.
8
Temperatura Requerida Para La Operación:
Este producto está diseñado para una
temperatura ambiental máxima de 40 grados C.
9
Para Todos Los Países: Monte el producto de
acuerdo con los Códigos Eléctricos locales y
nacionales.
10
Utilizar un adaptador de corriente alterna
autorizado TÜV de 7,5 voltios de corriente
continua y 1 amperios.
31
Standarder: Denna produkt uppfyller följande
standarder.
$
$
1
Radiostörning
2
$
$
Varning: Denna produkt kan ge upphov till
radiostörningar i hemmet, vilket kan tvinga
användaren till att vidtaga erforderliga åtgärder.
3
Immunitet
EN50082-1 1997
4
Elsäkerhet
UL 1950, EN60950,
VCCI Class B
$
$
$
$
$
$
32
EN55022 Klass B
Säkerhet
5
Varning: Nätkabeln används som strömbrytare
för att koppla från strömmen, dra ur nätkabeln.
6
Utrustning Med Plugg. Uttaget skall installeras i
utrustningens närhet och vara lättåtkomligt".
7
Varning: Luftventilerna får ej blockeras och
måste ha fri tillgång till omgivande rumsluft för
avsvalning.
8
Driftstemperatur: Denna produkt är
konstruerad för rumstemperatur ej överstigande
40 grader Celsius.
9
Alla Länder: Installera produkten i enlighet med
lokala och statliga bestämmelser för elektrisk
utrustning.
10
Använd en växelströmsanslutningsenhet
licensierad av TÜV.Likström 7,5V, 1A.