Manual - Backyard Leisure

CEDAR PERGOLA
Model: # 6213
••
••
••
••
Owner's Manual
Frequently Asked Questions
Assembly Instructions
Warranty Information
Manufacturer: Backyard Discovery
3001 North Rouse
Pittsburg, KS 66762
1-800-856-4445
Register your new swing set on-line @ www.swingsetsonline.com
(you will also find any updates on assembly instructions and
information to order replacement parts)
Features the
fastening system.
Save this assembly manual for future reference in the event that
you need to order replacement parts.
INS-6213-Cedar Pergola-Eng-A 07/24/12
Made in China
STOP
PARE
Missing A Part?
CALL US BEFORE GOING
BACK TO THE STORE!
The store where you made your purchase
does not stock parts for this item.
If you have assembly questions or if you need parts,
whether they are missing or damaged
Call Toll-Free Help Line or visit www.swingsetsonline.com
¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA!
La tienda donde realizó la compra no almacena piezas de este producto.
Si tiene preguntas sobre el ensamblaje o si necesita piezas debido a que
faltan o están dañadas
llame gratis a la línea de ayuda
1-800-765-4138
PLEASE READ THIS BEFORE STARTING ASSEMBLY
POR FAVOR LEA ESTAS INSTRUCCIONES ANTES DE COMENZAR EL ENSAMBLAJE
•
•
•
•
•
•
•
•
•
•
READ THE ASSEMBLY MANUAL COMPLETELY, PAYING SPECIAL ATTENTION TO THE IMPORTANT TIPS AND
SAFETY INFORMATION.
AFTER YOU HAVE READ THE ASSEMBLY MANUAL, YOU WILL BE ABLE TO DECIDE IF YOU NEED PROFESSIONAL
HELP TO COMPLETE THE ASSEMBLY OF THE PLAYSET.
SEPARATE AND IDENTIFY ALL PARTS TO MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED.
IF YOU CAN’T FIND ALL OF THE PARTS, CHECK THE PACKING MATERIAL. SMALL PARTS MAY HAVE FALLEN INTO IT
DURING SHIPMENT.
IF YOU HAVE PROBLEMS WITH THE ASSEMBLY OR IF ANY PART IS MISSING OR
DAMAGED, PLEASE CALL THE
HELP LINE 1-800-765-4138 OR VISIT www.swingsetsonline.com.
LEA EL MANUAL DE ENSAMBLAJE COMPLETAMENTE, PRESTANDO ESPECIAL ATENCIÓN A LOS CONSEJOS ÚTILES
IMPORTANTES Y A LA INFORMACIÓN SOBRE SEGURIDAD.
DESPUÉS DE QUE HAYA LEÍDO EL MANUAL DE ENSAMBLAJE, PODRÁ DECIDIR SI NECESITA AYUDA PROFESIONAL
PARA EFECTUAR EL ENSAMBLAJE DE LA UNIDAD DE JUEGOS.
SEPARE E IDENTIFIQUE TODAS LAS PIEZAS PARA COMPROBAR QUE DISPONE DE TODAS LAS PARTES INDICADAS.
SI NO PUEDE ENCONTRAR TODAS LAS PIEZAS, REVISE EL MATERIAL DE EMPAQUE. ES POSIBLE QUE ALGUNAS
PIEZAS PEQUEÑAS PUEDAN HABERSE CAÍDO ALLÍ DURANTE EL ENVÍO.
SI TIENE PROBLEMAS CON EL ENSAMBLAJE O SI ALGUNA PIEZA FALTA O ESTÁ DAÑADA, LLAME A LA LÍNEA DE
AYUDA AL 1-800-765-4138 O VISITE www.swingsetsonline.com.
PLEASE HAVE THE FOLLOWING INFORMATION WHEN YOU MAKE YOUR CALL:
1 – MODEL NUMBER OF THE PRODUCT LOCATED ON THE FRONT OF THE ASSEMBLY MANUAL
2 – DESRIPTION OF THE PART FROM THE PARTS LIST
POR FAVOR TENGA VISIBLE LA SIGUIENTE INFORMACIÓN CUANDO LLAME:
1 - NÚMERO DE MODELO DEL PRODUCTO QUE SE ENCUENTRA UBICADO AL FRENTE DEL MANUAL
DE ENSAMBLAJE
2 - DESCRIPCIÓN DE LA PIEZA QUE SE ENCUENTRA EN LA LISTA DE PIEZAS
Owner’s Manual Outdoor Product
Dear Customer:
Please read entire booklet completely before beginning the assembly process.
Structures are not intended for public use. The Company does not warranty any of its
residential structures subjected to commercial use such as: Recreational Park, or any
similar Commercial Application.
Please follow all recommendations below. Failure to do so may result in the warranty
being void and/or safety violations that could result in serious injury. This manual
contains helpful information concerning Assembly Preparation, Installation Procedure,
and Required Maintenance. Always keep safety in mind as your structure is being built.
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE
PLACE WHERE YOU CAN REFER TO THEM AS NEEDED. IN ORDER TO PROVIDE YOU
WITH THE MOST EFFICIENT SERVICE, IT IS REQUIRED THAT YOU PROVIDE US WITH THE
PART NUMBERS WHEN ORDERING PARTS.
For Your Records:
Please take time and fill out the information below. This information will be needed for
warranty issues.
Staple Receipt Here
Where Purchased: ______________
Date of Purchase: ________________
Installation Date: _______________
Installed by: ______________________
Maintenance Instructions:
1. Check all nuts and bolts twice monthly during the usage season and tighten as required.
(But not so tight that you crack the wood) It is particularly important that this
procedure be followed at the beginning of each season.
2. Oil all metallic moving parts monthly during the usage period.
3. Check all coverings for bolts and sharp edges twice monthly during usage season to be
certain they are in place. Replace when necessary. It is especially important to do this
at the beginning of each new season.
4. For rusted areas on metallic members such as hinges, brackets, etc. sand and repaint,
using a non lead-based paint meeting the requirements of Title 16 CRF Part 1303.
5. Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season
causing splinters to appear. Light sanding may be necessary to maintain a safe
environment. Treating your Product with protection (sealant) after sanding will help
prevent severe checking/splitting and other weather damage.
6. We have applied a waterborne translucent stain to your unit. This is done for color only.
Once or twice a year, depending on your climate conditions, you must apply some type
of protection (sealant) to the wood of your unit. Prior to the application of sealant,
lightly sand any “rough” spots on your set. Please note this is a requirement of your
warranty.
ENG OWNER OP-2010
Rev. 8/5/2009
Outdoor Product Assembly Manual FAQs:
1. Is the wood treated with chemicals? Backyard Discovery uses 100% Chinese Cedar wood
which is naturally bug resistant, decay and rot resistant. To help ensure your families
safety, our wood is completely chemical free and we do not use pressure-treated wood.
The stain we use is a top coat using a water-based product that is for appearance only.
2. How often should the product be stained? Backyard Discovery recommends the product be
stained once each year. A water or oil based stain can be used at the customer’s discretion.
3. Why does it seem that my product is developing cracks? Wood is a natural material; no two
pieces are exactly alike. Each piece has its own characteristics and personality and reacts
differently to climate changes. When any wood product is exposed to the elements, it
develops “wood checks”. A check is the radial separation of the wood fibers running with
the grain of the wood. These are caused by the varying temperature and moisture
conditions. A check is not a crack – it does not affect the strength or durability of the wood
or structural integrity of the product.
4. Do Backyard Discovery products come with a warranty? Yes. All Backyard Discovery
products carry a 1-year replacement warranty on all parts for manufacturer’s defect. Our
wood carries a 5 year warranty on rot and decay as well. Please see warranty details for
more information.
5. What is the best way to get started assembling the product? Backyard Discovery
recommends taking all the parts out of the boxes and arranging them by part number
before you begin any assembly. This will not only allow faster assembly, but will also
identify any parts that may be missing or damaged so they can be replaced before
assembly. If parts are missing or need replacement, go to
www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read
the assembly manual and get the tools ready for the job as recommended in the manual. If
the assembly manual is lost or misplaced a new one can be printed from Backyard
Discovery’s website: www.swingsetsonline.com .
6. The 2”x4” boards do not measure 2”x 4”. Why not? In the U.S. it’s common practice to
describe lumber dimensions using the rough cut sizes from the sawmill and not the finished
dimensions. Retailers, home stores, etc. all use this accepted practice for describing lumber
dimensions. However, Backyard Discovery products are designed and constructed using the
actual dimensions so everything fits properly and remains so during the life of the product.
For more information and frequently asked questions, please refer to our website at
www.swingsetsonline.com .
Tools Required for Installation:
(These are the tools that are generally required for assembly of our outdoor products. These tools
are not included with the outdoor product purchase.)
(Square)
(Level 24")
(Tape Measure)
(Cordless Drill or Electric Drill)
(Concrete Drill Bit)
(Phillips Screw Driver)
(Rubber Mallet - Optional)
(Drill Attachments: Phillips
(An Adult w/ an Adult Helper)
Head & Socket Driver)
(Ladder)
Basic Setup Dimensions
Place the pergola on level ground, not less than 6 ft [2 m] from any structure or obstruction such
as a fence, garage, house, overhanging branches, laundry lines, or electrical wires.
6'-0"
6'-0"
11'-11"
11'-11"
7'- 7/8"
7'-10 15/16"
Important Assembly Notes
1) While assembling unit, take time before and after each phase to make sure pergola is square and level.
If pergola is not square and level, assembly will be difficult and improper assembly may result. Extra care
must be taken to insure the pergola is square and level.
2) Tighten bolts securely.
3) Pay close attention to the ITEMS NEEDED FOR EACH PHASE. They can be a valuable aid when
sorting your wood and hardware. Assembly will be made easier if items are sorted by step.
4) Pay close attention to make sure you are using the correct hardware in the correct steps. Using
incorrect hardware may result in improper assembly.
5) Read each step thoroughly. The written steps may include important information not
shown in the illustrations.
Parts Identification
Wood Components
(NOT TO SCALE)
D1 - JOIST - W102219
(8) 1 3/8"x5 1/4"x75 1/4" (36x134x1912)
D2 - SLOTTED JOIST - W102218
(12) 1 3/8"x5 1/4"x75 1/4" (36x134x1912)
D3 - CENTER SLOTTED JOIST - W102217
(2) 1 3/8"x5 1/4"x75 1/4" (36x134x1912)
D7 - JOIST - W103318
(4) 1 3/8"x5 1/4"x75 1/4" (36x134x1912)
D9 - JOIST - W103351
(4) 1 3/8"x5 1/4"x75 1/4" (36x134x1912)
D70 - ANGLE BRACE - W103317
(4) 1 3/8"x5 1/4"x35 3/8" (36x134x900)
D71 - ANGLE BRACE - W103320
(4) 1 3/8"x5 1/4"x28" (36x134x710)
K1 - TIE PLATE - W103359
(30) 5/8"x5 1/4"x11" (16x134x280)
P1 - ROOF SLAT - W102216
(32) 1 3/8"x1 3/8"x61 7/8" (36x36x1572)
WP1 - PERGOLA POST - W102211
(4) 5 1/2"x5 1/2"x89 1/2" (140x140x2273)
Parts Identification
Hardware
(2) - T-40 Torx Bit - A100042
(17) VL - NUT BARREL WH 5/16x1-1/2 BLK - H100193
(124) VR - WASHER LOCK EXT 8x19 BLK - H100198
(17) VT - SCREW PFH 8x1-1/2 BLK - H100200
(122) VU - SCREW PFH 8x2-1/2 BLK - H100201
(101) VS - WASHER LOCK EXT 12x19 BLK - H100199
(9) VZ - LAG SCREW WH 5/16x3 BLK - H100206
(2) VW - SCREW PFH 8x1/2 BLK - H100203
(15) VX - LAG SCREW WH 5/16x5-1/2 BLK - H100204
(62) VY - BOLT WH 5/16x2-1/4 BLK - H100205
(17) VM - BOLT WH 5/16x2-1/2 BLK - H100194
(17) VP - BOLT WH 5/16x7-1/4 BLK - H100196
(2) VV - SCREW PWH 8x5/8 BLK - H100202
(17) CQ - CONCRETE ANCHOR 3/16x2" - H100120
(2) - T-40 Torx Wrench - A100041
(81) VK - NUT BARREL WH 5/16x7/8 BLK - H100192
Parts Identification
Accessories
(NOT TO SCALE)
(4) HT - FOOT 142 SQUARE POST - A100029
(1) VJ - LTP ID TAG (SMALL) WITHOUT AGES - A100387
(1) SQ - "A" REVISION TAG - A100314
Pergola Assembly
IMPORTANT ASSEMBLY TIPS
Assembly Tip:
• If during assembly of beams the
threads do not engage, install the
bolt without the star washer to seat.
Once seated loosen, add washer,
and re-tighten.
Assembly Tip:
• If during assembly the holes in the
beams and plates do not align you
may need to drill them using a 3/8"
drill bit for better fit.
Assembly Tip:
• To ease assembly and to reduce the
chance of splintering the beams,
lightly sand the leading edges of all
the notches using sandpaper.
• To reduce friction during assembly
apply bar soap to the surfaces of the
notches where shown.
Apply bar soap
to both sides.
Additional Assembly Tips:
• If it is necessary to pound on the beams using a hammer or rubber mallet, be sure to place a scrap of lumber
between the hammer and the beams. This will help to ensure the beam is not damaged.
• Lag screws may be used to pull together upper and lower beam assemblies.
NOTE: PROPER NOTCH ALIGNMENT MUST BE MADE TO ENSURE NO DAMAGE OCCURS
TO BEAMS.
(4)
D9 - JOIST - W103351
1 3/8"x5 1/4"x75 1/4" (36x134x1912)
(4)
K1 - TIE PLATE - W103359
5/8"x5 1/4"x11" (16x134x280)
STEP 1
NUT BARREL WH 5/16x7/8 BLK
(8)
WASHER LOCK EXT 12x19 BLK
BOLT WH
5/16x2-1/4
BLK
(8)
D9
K1
(8)
(8)
WASHER
LOCK EXT
12x19 BLK
WASHER
LOCK EXT
8x19 BLK
NUT BARREL
WH 5/16x7/8
BLK
D9
Assembly Tip:
• If during assembly the holes in the
beams and plates do not align you
may need to drill them using a 3/8"
drill bit for better fit.
WASHER LOCK EXT 8x19 BLK
Note:
Each board includes 4 holes.
BOLT WH 5/16x2-1/4 BLK
Note:
You will need to assemble
two of these joists.
Note:
Each board includes 4 holes.
(8)
D1 - JOIST - W102219
1 3/8"x5 1/4"x75 1/4" (36x134x1912)
(8)
K1 - TIE PLATE - W103359
5/8"x5 1/4"x11" (16x134x280)
STEP 2
NUT BARREL WH 5/16x7/8 BLK
(16)
WASHER LOCK EXT 12x19 BLK
(16)
BOLT WH
5/16x2-1/4
BLK
K1
(16)
(16)
NUT BARREL
WH 5/16x7/8
BLK
D1
D1
WASHER LOCK EXT 8x19 BLK
BOLT WH 5/16x2-1/4 BLK
Note:
You will need to assemble
four of these joists.
Note:
Each board includes 2 holes.
WASHER
LOCK EXT
12x19 BLK
Note:
Each board includes 2 holes.
WASHER
LOCK EXT
8x19 BLK
(4)
D7 - JOIST - W103318
1 3/8"x5 1/4"x75 1/4" (36x134x1912)
(4)
K1 - TIE PLATE - W103359
5/8"x5 1/4"x11" (16x134x280)
STEP 3
(8)
NUT BARREL WH 5/16x7/8 BLK
(8)
WASHER LOCK EXT 12x19 BLK
BOLT WH
5/16x2-1/4
BLK
(8)
K1
(8)
WASHER
LOCK EXT
12x19 BLK
WASHER
LOCK EXT
8x19 BLK
NUT BARREL
WH 5/16x7/8
BLK
D7
D7
WASHER LOCK EXT 8x19 BLK
BOLT WH 5/16x2-1/4 BLK
Note:
You will need to assemble
two of these joists.
Note:
Each board includes 4 holes.
Note:
Each board includes 4 holes.
(2)
D3 - CENTER SLOTTED JOIST - W102217
1 3/8"x5 1/4"x75 1/4" (36x134x1912)
(2)
K1 - TIE PLATE - W103359
5/8"x5 1/4"x11" (16x134x280)
STEP 4
BOLT WH 5/16x2-1/4 BLK
(4)
WASHER LOCK EXT 8x19 BLK
(4)
BOLT WH
5/16x2-1/4
BLK
(4)
K1
(4)
D3
D3
WASHER LOCK EXT 12x19 BLK
NUT BARREL WH 5/16x7/8 BLK
WASHER
LOCK EXT
12x19 BLK
NUT BARREL
WH 5/16x7/8
BLK
WASHER
LOCK EXT
8x19 BLK
(12)
D2 - SLOTTED JOIST - W102218
1 3/8"x5 1/4"x75 1/4" (36x134x1912)
(12)
K1 - TIE PLATE - W103359
5/8"x5 1/4"x11" (16x134x280)
STEP 5
(24)
NUT BARREL WH 5/16x7/8 BLK
WASHER LOCK EXT 12x19 BLK
(24)
BOLT WH
5/16x2-1/4
BLK
(24)
K1
(24)
D2
D2
WASHER LOCK EXT 8x19 BLK
BOLT WH 5/16x2-1/4 BLK
Note:
You will need to assemble six
of these joists.
WASHER
LOCK EXT
12x19 BLK
NUT BARREL
WH 5/16x7/8
BLK
WASHER
LOCK EXT
8x19 BLK
(4)
D71 - ANGLE BRACE - W103320
1 3/8"x5 1/4"x28" (36x134x710)
(2) OUTSIDE JOIST ASSEMBLY - (D9)
STEP 6
(8)
(8)
WASHER LOCK EXT 8x19 BLK
D9
BOLT WH
5/16x2-1/2
BLK
BOLT WH 5/16x2-1/2 BLK
D71
(8)
(8)
WASHER
LOCK EXT
12x19 BLK
WASHER
LOCK EXT
8x19 BLK
NUT BARREL
WH 5/16x7/8
BLK
NUT BARREL WH 5/16x7/8 BLK
WASHER LOCK EXT 12x19 BLK
D9
BOLT WH 5/16x2-1/2 BLK
WASHER LOCK EXT 8x19 BLK
NUT BARREL WH 5/16x7/8 BLK
WASHER LOCK EXT 12x19 BLK
D71
Note:
You will need to repeat this
process for the opposite side
joist.
(1) OUTSIDE JOIST ASSEMBLY - (D9)
(1) INSIDE JOIST ASSEMBLY - (D1)
(2)
(2) WP1-PERGOLA POST-W102211
5 1/2"x5 1/2"x89 1/2" (140x140x2273)
Note:
Angle braces 'D71' assemble
toward the inside of the
pergola assembly.
(4)
BOLT WH
5/16x7-1/4
BLK
WASHER
LOCK EXT
12x19 BLK
(6)
WASHER
LOCK EXT
8x19 BLK
LAG SCREW
WH 5/16x3
BLK
STEP 7
LEFT UPRIGHT
ASSEMBLY
(4)
(4)
NUT BARREL
WH 5/16x1-1/2
BLK
D1
D71
D9
WASHER LOCK EXT 12x19 BLK
NUT BARREL WH 5/16x1-1/2 BLK
WP1
WP1
D1
MAKE SURE
THAT YOUR
UNIT IS SQUARE.
D9
D71
WP1
LAG SCREW WH 5/16x3 BLK
WASHER LOCK EXT 8x19 BLK
WASHER LOCK EXT 8x19 BLK
BOLT WH 5/16x7-1/4 BLK
(1) OUTSIDE JOIST ASSEMBLY - (D9)
(1) INSIDE JOIST ASSEMBLY - (D1)
(2)
(2) WP1-PERGOLA POST-W102211
5 1/2"x5 1/2"x89 1/2" (140x140x2273)
STEP 8
Note:
Angle braces 'D71' assemble
toward the inside of the
pergola assembly.
RIGHT UPRIGHT
ASSEMBLY
(4)
BOLT WH
5/16x7-1/4
BLK
(4)
WASHER
LOCK EXT
12x19 BLK
(6)
WASHER
LOCK EXT
8x19 BLK
LAG SCREW
WH 5/16x3
BLK
(4)
NUT BARREL
WH 5/16x1-1/2
BLK
D1
D9
D71
NUT BARREL WH 5/16x1-1/2 BLK
WASHER LOCK EXT 12x19 BLK
D1
D9
D71
MAKE SURE
THAT YOUR
UNIT IS SQUARE.
LAG SCREW WH 5/16x3 BLK
WASHER LOCK EXT 8x19 BLK
WASHER LOCK EXT 8x19 BLK
BOLT WH 5/16x7-1/4 BLK
(4)
(2) OUTSIDE JOIST ASSEMBLY - (D7)
D70 - ANGLE BRACE - W103317
1 3/8"x5 1/4"x35 3/8" (36x134x900)
STEP 9
(8)
Note:
You will need to repeat this
process for the opposite side
joist.
(8)
WASHER
LOCK EXT
12x19 BLK
BOLT WH
5/16x2-1/2
BLK
(8)
(8)
NUT BARREL
WH 5/16x7/8
BLK
D70
D7
BOLT WH 5/16x2-1/2 BLK
WASHER LOCK EXT 8x19 BLK
D7
WASHER LOCK EXT 12x19 BLK
NUT BARREL WH 5/16x7/8 BLK
D70
WASHER
LOCK EXT
8x19 BLK
STEP 10
(8)
MAKE SURE
THAT YOUR
UNIT IS SQUARE.
Note:
Angle braces 'D70' assemble
toward the inside of the
pergola assembly.
LAG SCREW
WH 5/16x3
BLK
(4)
(12)
(8)
WASHER
LOCK EXT
12x19 BLK
BOLT WH
5/16x7-1/4
BLK
(8)
WASHER
LOCK EXT
8x19 BLK
NUT BARREL
WH 5/16x1-1/2
BLK
D7
D1
D7
D1
D1
D70
D70
D7
D70
WP1
WP1
WP1
WP1
NUT BARREL WH 5/16x1-1/2 BLK
WASHER LOCK EXT 12x19 BLK
D1
D7
WASHER LOCK EXT 8x19 BLK
D70
BOLT WH 5/16x7-1/4 BLK
WP1
LAG SCREW WH 5/16x3 BLK
WASHER LOCK EXT 8x19 BLK
(1) UPPER CENTER JOIST ASSEMBLY - (D3)
STEP 11
LAG SCREW WH 5/16x5-1/2 BLK
(2)
LAG SCREW
WH 5/16x5-1/2
BLK
(2)
WASHER
LOCK EXT
8x19 BLK
WASHER LOCK EXT 8x19 BLK
D3
LOCATE ON CENTER
D7
D1
D3
D1
D7
(6) UPPER SLOTTED JOIST ASSEMBLY - (D2)
STEP 12
LAG SCREW WH 5/16x5-1/2 BLK
WASHER LOCK EXT 8x19 BLK
LAG SCREW
D2
D2
(12) WH 5/16x5-1/2
BLK
D2
(12)
D7
D1
Assembly Tip:
D1
• THERE ARE PRE-DRILLED HOLES
LOCATED ON THE TOP EDGES OF
D7 BOARDS TO AID IN ASSEMBLY.
18 3/8"
D2
D7
18 3/8"
18 5/16"
18 5/16"
18 5/16"
18 5/16"
TOP VIEW
D2
WASHER
LOCK EXT
8x19 BLK
(16)
P1 - ROOF SLAT - W102216
1 3/8"x1 3/8"x61 7/8" (36x36x1572)
STEP 13
SCREW PFH 8x2-1/2 BLK
D2
P1
(48)
SCREW PFH
8x2-1/2 BLK
D3
8"
(15 PLCS)
1 1/4 OVERHANG
PURLIN POSITION
TOP VIEW - RIGHT CORNER
D3
D2
(16)
P1 - ROOF SLAT - W102216
1 3/8"x1 3/8"x61 7/8" (36x36x1572)
STEP 14
(64)
SCREW PFH 8x2-1/2 BLK
P1
P1
D3
D3
D2
SCREW PFH
8x2-1/2 BLK
(4) HT - FOOT 142 SQUARE POST - A100029
STEP 15
• Place the Pergola exactly where it will be anchored when completed.
Then slide a Foot 'HT' under each post 'WP1'.
WP1
WP1
WP1
WP1
HT
HT
HT
HT
STEP 16
• Use chalk to trace all the way around the edges of each foot 'HT'.
HT
STEP 17
• Move the Pergola aside. Place each Foot 'HT' inside of the lines drawn
around them in Step 16. Using a concrete drill bit, pilot drill attachment
holes into the concrete.
• Next, use the 3/16"x2" concrete anchor to attach each foot to the
concrete surface.
(16)
CONCRETE
ANCHOR
3/16x2"
CONCRETE ANCHOR 3/16x2"
HT
STEP 18
• Set the Pergola back in place, setting each post 'WP1' inside a 'HT' foot.
WP1
WP1
WP1
WP1
HT
HT
HT
HT
STEP 19
• Attach 'HT' Feet to each 'WP1' post using 1-1/2" deck screws into each
side, as shown.
(16)
WP1
HT
SCREW PFH 8x1-1/2 BLK
SCREW PFH
8x1-1/2 BLK
(1) SQ - "A" REVISION TAG - A100314
(1) VJ - LTP ID TAG (SMALL) WITHOUT AGES - A100387
(2)
STEP 20
• Place I.D. Placard 'VJ' on front of post approximately as shown.
• Place Revision Tag 'SQ' on rear of post approximately as shown.
(2)
SCREW PWH
8x5/8 BLK
SCREW PFH
8x1/2 BLK
REAR
FRONT
SQ
VJ
SCREW PWH 8x5/8 BLK
SCREW PFH 8x1/2 BLK
Limited Warranty
This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery
brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time
Products.
Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of
one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood,
hardware, and accessories. All wood carries a five (5) year pro-rated warranty against rot and decay. Refer to
the schedule below for charges associated with replacement of parts under this Limited Warranty. In addition,
Backyard Discovery will replace any parts within the first 30 days from date of purchase found to be missing
from or damaged in the original packaging.
This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is
required to assure maximum life and performance of this product and failure by the owner to maintain the
product according to the maintenance requirements may void this warranty. Maintenance guidelines are
provided in the Owner’s Manual.
This Limited Warranty does not cover:








Labor for any inspection
Labor for replacement of any defective item(s)
Incidental or consequential damages
Cosmetic defects which do not affect performance or integrity of a part or the entire product
Vandalism, improper use, failure due to loading or use beyond the capacities stated in the applicable
Assembly Manual.
Acts of nature including but not limited to wind, storms, hail, floods, excessive water exposure
Improper installation including but not limited to installation on uneven, unlevel, or soft ground
Minor twisting, warping, checking, or any other natural occurring properties of wood that do not affect
performance or integrity
Backyard Discovery products have been designed for safety and quality. Any modifications made to the
original product could damage the structural integrity of the unit leading to failure and possible injury.
Modification voids any and all warranties and Backyard Discovery assumes no liability for any modified
products or consequences resulting from failure of a modified product.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Backyard Discovery
product be used in public settings. Such use may lead to product failure and potential injury. Any and all public
use will void this warranty. Backyard Discovery disclaims all other representations and warranties of any kind,
express or implied.
This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state
or province to province. This warranty excludes all consequential damages, however, some states do not allow
the limitation or exclusion of consequential damages and therefore this limitation may not apply to you.
Pro Rated Part Replacement Schedule
Product Age
All Parts
0-30 days from date of purchase
31 days to 1 year
Wood Rot and Decay Only
1 year
2 years
3 years
4 years
5 years
Over 5 years
Customer Pays
$0 and free shipping
$0 + S&H
$0 and free shipping
20% + S&H
40% + S&H
60% + S&H
80% + S&H
100% + S&H