Siemens Silver WD7205 User manual

Operating and installation instructions
en
WD7005
Silver WD7205
Please read this specification carefully before you use the product.
Any failure and losses caused by ignoring the above mentioned items and cautions
mentioned in the operation and installation instruction are not covered by our warranty
and any liability. Please keep all documents in a safety place for future reference. If
you have any doubt, please contact our local service center of dealer.
If you need an English user manual, please download it from siemens web. Or you
can send the E-mail to service department, or you can call up service hot line for free
supply. Thanks!
http://www.siemens-ha.com.cn
Careline.China@BSHG.com
4008899999
生产厂家: 中德合资 博西威家用电器有限公司
厂 址: 中国江苏省无锡市高新技术开发区旺庄路66号
邮 编: 214028
Table of Contents
Disposal Information. . . . . . . . . . . . . . . . . . . . . . .2
Operating Instructions
Environmental Protection/Conservation Issues. . 3
Safety Precautions and Warnings. . . . . . . . . . . . .4
Your New Washing Machine. . . . . . . . . . . . . . . . .6
First Wash Cycle. . . . . . . . . . . . . . . . . . . . . . . . . 13
Preparing, Sorting and Loading the Laundry. . . . 14
Laundry Detergents and Additives. . . . . . . . . . . . 18
Washing/drying with standard settings. . . . . . . . . 20
Washing/drying with individual settings. . . . . . . . 23
When the Programmme has Ended. . . . . . . . . . . 27
Individual programme. . . . . . . . . . . . . . . . . . . . . . 29
Cleaning and Care. . . . . . . . . . . . . . . . . . . . . . . . 31
Troubleshooting Minor Faults. . . . . . . . . . . . . . . . 35
Customer service. . . . . . . . . . . . . . . . . . . . . . . . . 38
Programme table. . . . . . . . . . . . . . . . . . . . . . . . . 39
Installation Instructions
Installation, Connection and Transport. . . . . . . . . 41
Appendix
Technical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Package Sheet. . . . . . . . . . . . . . . . . . . . . . . . . . 51
1
Environmental Protection
Through the economical use of energy, water and detergent, your appliance is kind to the environments as
well as your household budget.
You can increase the economy and environmental
friendliness of your washer-dryer by washing maximum loads:
refer to page 39 program table
How to save energy:
For small amounts of laundry, the automatic control
system reduces the consumption of both water and
energy. Where possible, use the 60 C Cottons/coloureds programme with additional function Intensive Stains instead of the 90 C Cottons/coloureds
programme. The extended washing duration means
that a cleaning result comparable to that of the
90 C programme is achieved using considerably
less energy.
How to save water, energy and detergent:
Avoid using the Pre-wash function when washing
lightly normally soiled laundry.
How to save energy and time:
For lightly soiled laundry, select the short
programme appropriate to the type of textile.
How to save detergent:
Add detergent according to the degree of soiling,
amount of laundry and water hardness, and
observe the detergent manufacture s instructions.
Save energy:
If washing is then to be dried in the appliance, select
the higher spin speed - because the more water that
is spun out of the appliance, the less time and
energy is required to dry it.
3
Disposal Information
The new machine s
packaging
Dispose of packing materials in a responsible manner.
Keep packing materials out of the reach of children.
Packing materials are not toys. Reprocessing and reusing materials saves raw materials and reduces waste. All packing materials used are environment friendly and reusable. Cardboard boxes consist of 80% to
100% recycled paper. Plastic wrappings are made
from polythene(PE), the tapes are made from polypropylene(PP) and the CC-free packing is made from
foamed polystyrene (PS). These materials are pure
hydrocarbon compounds and can be recycled.
Your old machine
Render the washer-dryer inoperable when it can
no longer be used Remove the plug from the socket and cut off the power cable. Destroy the catch
on the porthole door. Prevent children at play from
being locked in and risking death by suffocation.
The old machine contains valuable materials which
should be recycled. Please make your contribution
to the environment by assisting with proper disposal or recycling.
2
Precautions and Warnings
Before using for the first time:
Please read the enclosed documents carefully
before using the Washer-dryer for the first time.
They contain important information on the installation, use and safety of the machine.
The manufacturer does not accept liability if these
instructions are not followed.
Please contact an authorized technician to install
the machine and instruct the using method.
Please keep all documents in a safe place for
future reference.
Install the Washer-dryer in accordance with the
instructions (page 41-49). Remove the transit bolts
and keep them in a safe place.
The washing machine must be installed and
operated in a room with the drain.
When heating, the maximum current of the washing machine is 10A,so please make sure that the
power supply system(voltage; current and the
cable) is applicable to the load of the applied
appliance.
In order to ensure your safety, you must plug the
cable into a socket which connected to earth. And
please check your socket to make sure that it is
connected with reliable earth correctly.
If the Washer-dryer is visibly damaged, do not
connect it up. If you are in doubt, contact your
customer service representative or dealer.
This Washer-dryer use thread connection water
inlet hose, connect it to the water tap together with
the machine according to the require of page 45.
(carry out by an authorized technician)
4
When washing
and drying:
Operate the Washer-dryer with cold tap water only.
Your Washer-dryer is designed for domestic use
only, i.e. For washing machine-washable textiles
in a detergent solution.
Due to the use of the condensation principle in
drying, please keep the connected water tap open
during the drying process.
Never use flammable; explosible and/or poisonous
solvents such as gasoline; alcohol etc. As the washing lotion. Please only use the lotions suitable
for using in washing machine available in
the market.
Never wash the carpet in the washing machine.
Kepp children and pets away from the washing
machine.
When the program
has ended:
Taking care of your
machine:
Exercise caution when pumping out hot detergent
solution.
Never open the door when drying.
When the program has ended:
The End is indicated(If you select no final spin
function, see page 27).The buzzer of machine
sounds(the duration is 10 minutes) to remind the
user that the programme has ended. Open the
loading door after cutting the power of machine.
After the program has ended, please cut the supply
of power and water immediately.
Do not climb onto the washing machine.
Do not lean against the door.
Do not expose the machine in the place with
causticity or explosibility gas.(e.g. dust, steam
and gas, etc.)
Do not install the washing machine in a bathroom or a room very wet.
Please close the door gently, if the door can not be
closed, please check if the laundry are balanced.
When transporting
the machine:
Insert the transit bolts by technician.
Drain any water left in the machine.
Take care when moving the machine.
Do not lift the machine by any of the protruding
parts,and the loading door.
5
Your new washer-dryer
Filling laundry detergent
and/or additive dispensers.
Chamber I:
Detergent for pre-wash,starch,
or pre-soaking agent.
Chamber II:
Detergent for main washing period,
water softener, blench and stainremoving salt.
Chamber :
Additives, e.g. fabric softener or
former(Do not exceed Max )
Open the loading door
6
and close it
Drain washing solution
if necessary.
Control Panel
Start button
For starting the wash/dry cycle
(program must have been
selectd).
Programme selector
For switching the washer-dryer on and off and for
selecting the program. Can be rotated in either
direction. If rotate it during the washing/drying,
the program will be stopped. The program
sequence is electronically controlled.
Buttons for additional options
(In addition to the programme if
required)
Intensive Stains: extend the
washing duration
Extra Rinse: additional rinsing cycle
Less Ironing: gentle spin
Prewash: actuate prewash
Additional options can be combined.
Display pannel
Indicates the settings which have
been selected(e.g. Spin speed, Time
delay, Childproof lock, Maximum load)
Button
Selects the the start time(delays the
start of the program).
Button
Select the drying time
Button
Selects the spin speed or no final spin.
The indicator lights of the buttons
come on if the additional options
are active.
Switching off the additional option:
Press the button again. Indicator
light goes out.
7
Display panel
Display
q
Notes
Prewash
Washing
programme status
On if selected
Not on if rinse, spin or
drain additional programme
was selected
Rinse
Not on if spin or drain
additional programme was
selected
Final spin/Empty
Not on if a programme with
,,
the --- setting(without
final spin)
Drying
Not on if dry programme
or dry time was selected.
Progress bar
For the programme status
Overdosage
On if too much detergent
dispensed
Childproof lock
On if selected
Fan
Not on if dry programme or
dry time was selected
,,
5.2kg*Maximum load
1000rpm* Spin speed or
no final spin
Z ---*
Not on if rinse,spin or
drain additional programme
was selected
Maximum spin speed of the
programme or selected speed
120min*
Drying time
Selected drying time
,
1 h*
Start time
Selected start time
Other displays at this location:
1:00* Programme duration
Expected programme duration
End of programme or
--- End of programme without final spin or
E02* Fault display
See page 33
* Examples of the display, it will be changed
according to your selected programme.
8
Programme status
display
Overdosage
The first row of symbols and the progress bar below form
the program status display. The progress bar consists of
a frame and several segments.
When the programme has been selected, the symbols
for the individual programme sections are displayed.
The frame of the progress bar flashes and requests
the programme to start.
When the programme has started, the almost empty bar
is displayed which fills up with segments from left to right
while the programme is running. The symbols indicatethe
programme sections which have not yet run and go out
when th e particular programme section has run.
At the end of the programme all symbols have gone out
and the progress bar is full.
The automatic safety system detects excessive froth in the
appliance due to a highly frothing detergent or an overdosage At the end of the programme this is indicated in the
display field by the
symbol. Dispense less detergent for
the next wash with similar items of washing(same degree
of soiling and wash load).
Overdosage of detergent may cause excessive froth formation and impair the washing and rinsing results. A rinse
cycle is automatically run.
i
The
symbol goes out when the appliance switches off at the end of the programme or if the programme
is changed.
Childproof lock
The activated childproof lock prevents the selected program from being changed while the programme is running,
see page 25.
Fan
The fan works at the last 10 minutes of drying duration for
cooling the laundry.
i Do not interrupt this cooling process.
Maximum load
The maximum wash/dry load is displayed depending on
the selected programme and additional functions,
see page 39.
Spin speed
The maximum spin speed is displayed depending on the
selected programme and additional functions.
n )
pi m
. S (rp
ax d
M pee
s
Progra
-mme
cottons easy-care delicates
wool
washing
rinsing spinning
model
WD7005
Silver WD7205
1000
800
600
800
800
800
800
1200
800
600
800
800
800
800
9
Programme duration
When the programme has been selected, the expected
programme duration(time after which the programme is
expected to end) is displayed.
The programme duration is displayed in hours and
minutes, e.g.
01:17
1 hour and 17 minutes
00:35
35 minutes.
When the programme has started, the colon : flashes between hours and minutes and the programme duration
counts down in minutes.
When the programme ends, the displays shows
(if select no final spin function, see page27).
i While the programme is running,the programme duration
may be extended or reduced for the following reasons.
Reductions in time occur because of :
small loads,
reduced heating times,e.g. If the water is very hot.
Increases in time occur because of:
additional rinse cycle if excessive foam is in the laundry,
multiple spinning if the laundry is distributed poorly
in the drum,
increased heating times,e.g. When the water is
too cold,
water pressure too low,
selection of an additional option,e.g. Intensive Stains
function after the programme has started.
Very absorbent washing extends the heating duration.
Start time
Drying duration
10
You can delay the start time,see page 24
You can set the drying duration.
When the washing and drying without a break was
selected, drying duration will add in programme duration automatically. Cotton quick washing programmes will prolong 10 minutes and other cotton
programmes will prolong 5 minutes for good washing
performance.
,,
Programme buttons
Select the desired programme(refer also to separate
Programme table ).
Cold, 40 C Cottons/coloureds
For hard-wearing fabrics.
Basic program
30 C quick washing Cottons/coloureds
For less soiling fabrics made from cottons or linen.
This duration is shorter.
60 C Cottons/coloureds
For very dirty ,hard-wearing fabrics.
Select this program can remove stain as protein and
so on.
90 C Cottons/coloureds
An energy-intensive program for heat-resistant fabrics
made from cotton or linen.
For the protection of the drainage pipe, the hot washing solution is mixed with approx. 5 liters of cold water
before being drained.
Intensive dry
For cottons/coloured textiles, dry at normal heat setting.
Cold, 40 C, 60 C Easy-care
For easy-care fabrics made from cotton, synthetics or
blended fibres.
Gentle dry
For easy-care textiles, dry at low heat setting.
30 C Delicates
For sensitive, easy-care fabrics made from cotton,
synthetics or blended fibres, and net curtain. No spinning between rinsing cycles.
Cold, 30 C Wool
For hand or machine-washable fabrics made from
wool or wool blend.
11
Additional function
Washing
Separate washing cycle.
Rinsing
Separate rinsing cycle with subsequent spin cycle for
easy care fabrics.
Spin
Separate spin cycle. Washing solution or rinsing water
is drained prior to the spin cycle.
Drain
Draining of the rinsing water after a wash programme
with the without drain setting for the gentle treatment
of delicate laundry.
(You can select an additional function if necessary)
Additional function
Intensive stains
For very dirty clothes, the washing duration will be
prolonged 20 to 60 minutes after pressing this button, and this is decided by the programme that you
selected.
Extra rinse
An additional rinsing cycle performed; the washing
duration will be prolonged 10 minutes.
Less Ironing
Special spin cycle with post-spin loosening cycle.
The laundry is left lying loosely in the drum, thus
reducing creasing. After pressing this button, the
washing duration and max spin speed will be chan
ged.
cottons
Easy
-care delicates wool rinsing spinning
others
30 C
washing prolonged time 10 min 5 min
maximum spin speed
800rpm
5 min
5 min
no
5 min
5 min
600rpm
Prewash
For very dirty fabrics,washing duration will be
prolonged 20 minutes.
Observe the maximum load for each type of fabric;
Remove the laundry immediately after the spin cycle.
12
The installation of the washer-dryer is finished.
(See page 41-49)
Each washer-dryer has been tested in the factory.
A little bit of water can be left in the drum during the
test. Please carry out the first wash cycle without
laundry to remove any water left over from the
factory tests.
Do not load any laundry.
Turn the tape ON.
Pull the detergent drawer out as far as it will go.
Input about 1 liter of water in chamber II.
Pour half a measuring cup of detergent into
chamber II.
Do not use a special detergent for delicates or
wollens as these will create too much foam.
Close the detergent drawer.
Close the washer-dryer door.
Turn the programme selector to 90 C Cottons/
coloureds.
,,
Press the Start button. The washing programme
starts.
,,
First Wash Cycle
The programme ends when all symbols in the upper
row of the display field go out, the progress bar is
completely filled and the programme duration is on
,the buzzer sounds.
Turn the programme selector to off position.
13
Preparing/sorting and loading
the laundry
Preparing the laundry
Remove any loose items or metal objects, such as
safety pins, paper clips, etc. from the laundry.
Brush sand, coins, etc. out of pocket and cuffs.
Close zips and button up cushion covers, duvet
covers, etc.
Remove curtain runners, or secure them in a net
bag.
Particularly delicate items, such as tights or lace
curtains, or smaller items, such as tiny socks or
handkerchiefs, should only be washed in a net
bag or pillow case.
Some items are best turned inside out. These
included knitwear, trousers, T-shirts and
sweatshirts.
Make sure that the wire-cup bras are machine
washable.
!Make sure that wire-cup bras in a pillow case which
can be securely closed with a zip or buttons. If the
wire works itself out of the cup it may fall through
the holes of the drum and cause extensive damage.
Preparing laundry for
drying
Only tumble-dry textiles which have been washed,
rinsed and spun.
Remove as much water as possible from the laundry.
Do not press the button for reducing the spin speed.
Before tumble-dring, ease-care items should also be
spun using the appropriate spin programme (see
programme table)
In order to ensure uniform drying, sort the items
according to fabric type and degree of drying
required.
Easy-care items should if possible be removed from
the washer-dryer while still slightly damp and allowed
do continue drying in the open air. Overdrying may
cause excessive creasing.
Items which require ironing do not have to be ironed
immediately after being tumble-dried. It is a good
idea to fold or roll them together for a while, so that
any remaining moisture is evenly distributed.
14
Sorting the laundry
According to colour
and degree of dirt
Caution
Items of clothing can become discoloured. Never wash
new multi-coloured items together with other items.
White items may become grey. Always wash white and
coloured items separately.
Slight dirt
No recognizable dirt or staining. Laundry may have
some body odour.
- Light summer clothing and sportswear that has only
been worn for a few hours.
- T-shirts, shirts and blouses that have been used for
one day.
- Bed linen and guest towels that have been used for
one day.
Normal dirt
Visible dirt and/or some light staining recognizable.
- T-shirts, shirts and blouses that are very sweaty or
have been worn several times.
- Underwear that has been worn for one day.
- Tea towels, hand towels and bed linen that have
been used for up to one week.
- Net curtains (without nicotine staining) that have
not been washed for up to 1/2 year.
Intensive dirt
Dirt and/or staining reconizable.
- Kitchen hand towels that have been used for up to
one week.
- Fabric napkins.
- Children's outer clothing or football shirts and shorts
with grass and soil stains.
- Working clothes such as overalls or baker's and
butcher's coats.
15
Typical stains
- Skin fat, cooking oils/fat, sauces, mineral oil,
wax(containing fat/oil)
- Tea, coffee, red wine, fruit, vegetables(blea chable).
- Blood, egg, milk, starch(containing protein/
carbohydrate).
- Soot, soil, sand(pigments), red sand on tennis
clothes.
Removing stains
Wherever possible, remove/pretreat stains whilst
they are still fresh. First, dab soapy water onto the
stain. Do not rub. Subsequently wash the items of
clothing using the appropriate programme.
Several washing cycles may sometimes be required
in order to remove stubborn/dried in stains.
Sorting laundry according
to their care label
specifications
Only wash laundry that is labelled with the following
care symbols:
95
90
90 C Cottons + lines
60
40
30
60 C, 40 C, 30 C Cottons + linens
60
40
30
60 C, 40 C, 30 C Easy-care
40
40
30
30
40 C, 30 C Delicates
40
40
30
30
40 C, 30 C Wollens (hand and machine-washable)
Laundry that is labelled with the following care symbol
must not be washed in the washing machine.
= do not wash
Only dry laundry that is labelled with the following care
symbols
=Tumble-dry at normal heat setting (intensive dry)
=Tumble-dry at lowl heat setting (gentle dry)
16
The following textiles should not be tumble-dried:
Laundry marked with the care symbol:
=Do not tumble-dry
- Wollens or items containing wool. Risk of shrinking!
- Delicate fabric (silk, synthetic net curtains).
Risk of creasing.
- Items containing foam rubber or similar material.
- Items which have been treated with inflammable
solvents, such as stain removes, petrol, paint
thinners. Explosion hazard!
- Items still containing hair lacquer or similar
substances. Dangerous vapors!
- Dripping-wet laundry. Waste of energy!
Loading the laundry
! Risk of explosion
Items of clothing that have been pretreated with
solvent-based cleaning agents, e.g. Stain remover
and dry cleaning spirit, represent an explosion
hazard once loaded into the washer-dryer.
Therefore, these items must be rinsed thoroughly
by hand.
Caution:
Loose debris in the washer-dryer drum can damage
the laundry. Before loading the laundry, check that
there is no debris in the drum.
Open the loading door.
Unfold the sorted items of clothing and place them
loosely into the drum. Mix up large and small items.
Items of varying size will distribute better during
the spin cycle..
Do not exceed the maximum load: Overloading
will cause poor wash/dry results and encourage
creasing.
When washing/drying a small amount of laundry,
the washer-dryer automatically reduces the
amount of the water and energy used.
Close the loading door.
Take care not to trap any items of clothing between
the loading door and rubber seal.
咔嗒
17
Laundry Detergents and Additives
! Risk of explosion
Do not use solvent-based cleaning agents in fully
automatic washer-dryer. Explosion hazard.
Keep detergents and additives out of the reach
of children.
Caution:
You can use any standard powder or liquid detergent
which is suitable for automatic washer-dryer.
Do not use any detergent boosters containing solve
-nts or dirt and stain-removing spraying near the ma
-chine, as these could damage the machine.
Do not use non-automatic detergent as these produce too much foam.
Amount of detergent
The best washing results will only be achieved if
you add the correct amount of detergent. Observe
the instructions for use shown on the detergent
packing
When using liquid detergents, you can use any
measuring aids provided with the detergent, such
as dosage balls of bags.
Please put the liquid detergents into correct chamber.
The amount of detergent depends on:
- water hardness
- degree of soiling
- size of load
- amount of detergent to be added according to its
manufacturer.
Dispensing the correct amount of detergent relieves
the strain on the environment and ensures optimum
washing results.
18
Frequent use of insufficient detergent will eventually
become noticeable as followings:
- washing appears grey or not properly clean
- grey-brown stains (grease marks) form on the
washing
Too much detergent results in:
- unnecessarily high environmental pollution
- due to the generation of too much foam, the
washing is hard
-ly agitated which leads to poor washing results.
The amount of detergent indicated on its packaging
refers to a full machine load.
For small loads or less soiling, reduce the amount
of detergent.
Filling laundry detergent
and/or additive
Dispenser I:
dispensers
Detergent for prewash or starch.
Dispenser II:
Detergent for main wash, water softener, presoaking agent, bleach and stain removal product.
Detergent
Cleaning product, e.g. Fabric softener or fabric
conditioner (do not fill above the
,, lower edge of
the insert 1).
,,
- Do not fill beyond the Max mark, otherwise will
be flushed o the machine together with the
detergent at the start of the programme.
- If the liquid additive is thick, mix with a little water
before dispensing (prevents clogging of the overflow).
Pull out the detergent dispenser up to the end stop.
Add the detergent and/or additive.
Close the detergent dispenser.
19
Washing/drying with standard settings
Your washer-dryer can be used in three ways:
- washing only,
- drying only,
- washing and drying without a break in between.
Caution:
For interrupted washing and drying, the maximum
load must be reduce to 2.6kg for cottons/coloureds
or 1.5kg for easy-care. Furthermore, it is possible
that certain types of laundry will not be dried
satisfactorily using the non-stop mode.
The economic using way:
wash and dry with recommended loads.
Setting the washing
programme or washing
and drying without
interruption
(Example of easy-care 40 C programme)
1. Turn the tap ON.
2. Turn the programme selector to the desired
programme (see programme sheet, page 26).
3. If required, press the button(s) for additional
option(s).
The indicator light of the selected button is on.
20
4. The frame of the progress bar flashes in the
display field and the following is displayed for
the selected programme:
- the symbols for the programme sections,
- recommended load,
- maximum spin speed,
- drying duration (displays 0 min, if the laundry
needs to be dried, please refer to setting the
drying time),
- programme duration.
Load the laundry and close the loading door.
Do not exceed recommended loads.
If you do not need your laundry to be dried
immediately in the machine after the washing
programme, please read the instructions for
starting the programme. Otherwise, please set
the drying time according to the instructions.
5. Press the
button to set the desired drying time,
the programme will be washing and drying without
interruption.
The indicator light of additional function goes out if
the additional function is selected, it is not available
when a drying cycle comes subsequently.
The spin speed and programme duration will be
changed accordingly after the drying time being
setted. See page 9.
The maximum load is also changed, do not exceed
recommended washing/drying loads.
The frame of the progress bar flashes in the display
field and the following is displayed for the selected
programme:
- the symbols for the programme sections, drying
and fan ,
- recommended load,
- maximum spin speed,
- drying duration,
- programme duration.
,,
,,
6.Press the Start button. The programme starts.
i The almost empty progress bar is indicated in the
display field. The recommended load goes out.
While the programme is running, the programme
duration counts down and the progress bar fills up
with the segments. The symbols for the run
programme sections go out.
21
Setting the drying programme
1. Turn the tap ON.
Due to the use of the condensation principle in
drying, please keep the connected water tap open
during the drying process.
2. Turn the programme selector to the desired
programme. (See programme sheet)
3. Press the
button to set drying time.
The frame of the progress bar flashes in the display
field and the following is displayed for the selected
programme:
- the symbols for the programme sections, drying
and fan ,
- recommended drying load,
- drying duration,
- programme duration.
Load the laundry and close the loading door.
Do not exceed recommended loads.
,,
,,
4. Press the Start button. The programme starts.
i The almost empty progress bar is indicated in the
display field. The recommended load goes out.
While the programme is running, the programme
duration counts down and the progress bar fills up
with the segments. The symbols for the run
programme sections go out.
Washing and drying with individual is described
subsequently.
22
Washing/drying with individual settings
You can adjust the setting to your requirements. First
find a quick overview of the adjustable settings. The
steps for changing the setting are described in detail
overleaf.
Turn the programme selector to the desired programme
Load the laundry and close the loading door
Spin speed
Start time
Page 24
Can be set in 1-hour steps
Page 24
Or without final spin
ZZ˜ further settings or press the start button
Make
Childproof lock
Page 25
23
Spin speed
The maximum displayed spin speed depends on the
selected programme.
Press
button until the required spin speed.
,,
,,
If setting --- (without final spin) has been selected,
the washing remains in the final rinsing water.
i Before the laundry can be unloaded, the Empty or
Spin programme must be performed. Or pressing
button to select the desired spin speed.
The spin speed can be changed at any time by
pressing the
button
until the desired speed is
,,
,,
displayed. Setting --- (without final spin) is
possible until the Rinse programme section starts.
Start time
Before a programme start, you can specify by how
many hours the start of the programme is to be
delayed.
Press the
button,
appears in the display.
Press the
button until the desired number of
hours is displayed.
i The first line of the programme flashed between
and .
The start time can be set in 1-hour steps. The time
i can be delayed up to a maximum of . If a start time
of has been set , the programme duration time
can be accessed by pressing the
button again.
i The time delay is counted down by the hour. When
the start time has elapsed, the program starts automatically and the programme duration is displayed.
Changes to the start time or an immediate start
i are possible. To do This:
-
-
24
Briefly set the programme selector to another
programme.
When the programme selector has been reset
to the original programme, individual or all other
settings may have to be re-selected. If required,
reset the start time.
,,
,,
Press the start time. The programme starts.
Childproof lock
You can secure your washing machine to prevent
selected functions from being inadvertently changed.
If the childproof lock has been selected:
No changes can be made while the programme is
running.
The symbol
flashes if a programme setting is
inadvertently changed,
Should the appliance be switched off and on while
a programme is running the programme will
continue at the point at which it was interrupted.
Activating the
childproof lock
Set the program selector to the required programme.
If required, select other settings.
Load the laundry and close the loading door.
Press the
,,
start
i Release the
,,
,,
button. The programme starts.
start
,,
,,
,,
,,
,,
button.
Press the start button and hold down ( for
approx. 4 seconds ) until the
symbol is
displayed.
Press the start button, the childproof lock is
activated, the symbol is
permanently on.
4 sec
Deactivate the
childproof lock
The childproof lock must be deactivated before
making programme changes or ending programmes
,,
,,
with setting --- (without final spin).
,,
,,
Press the start button and hold down (for
approx. 4 seconds ) until the
symbols goes out.
25
Change a programme
If you have accidentally selected the wrong
programme:
If the childproof lock is active, temporarily
deactivate; see page 25.
Turn the programme selector to a newly selected
programme. If prewash is selected subsequently,
set the programme selectors to off and reselect
the programme.
If required, change the other settings; see page 23.
,,
,,
Press the start button. The programme starts.
Cancelling active
programme
A pause in active
programme
If you wish to prematurely end a programme:
If the childproof lock is active, deactivate; see
page 20.
Turn the programme selector to Empty or Spin
programme. If required, select the desired spin
,,
speed (but not setting ---,, (without final spin).
,,
,,
Press the start button.
If you want to add/remove the laundry during active
programme
and the set programme sequence will not be changed.
Remove the plug from the sockeet.
Wait about 2 minutes, open the loading door.
Add/Remove the laundry
Reconnect the power supply, the memory function
of the washer-dryer will continue the interrupted
programme. So, the time in the display field may
be different from previous display.
Also, in the case of power failure or the power is
accidentally cut off, after the power supply comes
back, the washer-dryer will continue the interrupted
programme.
26
When the Programme has ended
i Display panel:
All symbols on the programme status display have
gone out, the full bar is displayed.
The programme duration is on
.
If the childproof lock is selected, the
symbol
illuminates.
If the detergent was overdosed, the
symbol
illuminates.
Selected spin speed illuminates.
If the drying time was selected, the drying time
illuminates.
If required, deactivate the childproof lock.
Turn the programme selector to off position.
,,
Setting ,,- - - (without
final spin ) selected
i Display panel:
The
symbol and the full bar are indicated on
the programme status display.
,,
The programme duration is on - - -
,,
If the childproof lock is selected, the
illuminates.
.
symbol
If required, deactivate the childproof lock.
Select an additional programme Empty or Spin.
Or press
button to select spin speed.
Press the start button.
After Empty or Spin programme ends, if detergent
was overdosed, the
symbol illuminates.
Turn the programme selector to off position.
27
Unloading the laundry
Turn off the water tap.
Open the loading door.
If the loading door can not be opened:
Wait for 2 minutes ( the safety function is active ) or
there is still water in the washer-dryer if the without
final spin option was selected. In the latter case,
select the Draining or Spinning programme.
Unload the laundry.
Caution:
Remove any debris (e.g. Coins, paper clips )
from the drum and rubber seal---risk of rust
formation!
Leave the loading door open to allow the inside
the washing machine to dry out.
After tumble-drying:
Carry out the loads after drying immediately.
Cottons / coloureds
,,
- Cotton ans linen items which have been dried to
iron dry should be rolled together to prevent them
from drying out completely before they are ironed.
,,
,,
- Cupboard dry items must be smoothed out and
folded up.
Easy-care / synthetics
- Hang shirts and blouses on individual hangers.
28
Special Applications
Pre-soak
Load laundry of the same color.
Add the pre-soak agent to chamber II according
to the manufacturer ,s specifications.
,,
Turn the program selector to Cold, Cottons/
coloureds ,,.
,,
Press the Start button.
,,
The Active control light comes on and the
program starts.
,,
,,
After approx. 10 minutes, turn the programme sel,,
ector to Off . The laundry is left to lie in the water.
,,
Select a programme after the desired soaking
period.
Do not add any additional detergent. The presoak solution continues to be used in the wash
program.
The laundry must not be treated with fabric softener,
Load the laundry.
Dispense the correct amount of starch for
approx.15 liters of water. Powered starch
must first be dissolved in water according
,
to the manufacturer s specifications.
,,
Turn the program selector to Rinsing .
,,
,,
Set the spin speed( without drain is also
possible).
,,
,,
Press the Start button.
,,
Starching
29
As soon as water starts to enter the machine:
Pull out the detergent dispenser slightly.
Add the starching solution to chamber I.
Close the detergent dispenser.
,,
If the without drain option is selected,the
,,
Draining program must be subsequently be
selected.
,,
,,
Dyeing
Only use dyes that are environmentally compatible and suitable for use in washing machines.
Caution
Discoloration of the laundry in subsequent wash
cycles cannot be completely ruled out.
Always use dyes in accordance with the manufacturer ,s instructions.
After dyeing:
Add 1/2 a measuring beaker of detergent to
chamber II.
Without any laundry in the drum, allow the
90 LC Cottons/coloureds,, program to run through.
,,
Wipe the seal clean.
Decolorizing
Caution:
Decolorants may contain sulphur or chlorine.
These substances can cause parts of the
washing machine to corrode. Do not decolorize
items of laundry in the washing machines.
30
Cleaning and Care
! Risk of electric shock!
Always disconnect the appliance from the mains
before cleaning.
! Risk of explosion!
Never use solvents to clean the appliance.
Never clean the washer-dryer with a jet of water.
Cleaning the appliance
housing and control
panel
As required:
Use hot soapy water or a mild, non-abrasive
leaning agent.
Rub dry with a soft towel.
Cleaning the drum
In the event that rust spots have formed due to leftover
debris (e.g. Coins, paper clips, needles, nails):
Use a chorine-free cleaning agent. Follow the
,
manufacturer s instructions. Never use steel wool.
Clean the detergent
dispenser
In the event that residual detergents or additives have
accumulated.
Pull out the detergent dispenser up to the end stop.
Press down the hollow on the insert and remove
the detergent dispenser completely.
31
Pull up the insert.
Rinse the detergent dispenser under hot running
water.
Push down the insert until it clicks into place.
Insert the detergent dispenser.
Clean the drain pump
This is necessary if the washing solution can not
be completely drained. The pump is blocked by
either loose debris or fluff which accumulates if
fluff-giving fabrics are washed at high temperature.
Draining the washing solution The water in the drum should be drained first
before cleaning the drain pump. Have a suitable
container ready.
! Risk of Scalding
Allow the hot washing solution to cool.
,,
,,
Turn the programme selector to Off .
Fold down the cover panel.
Carefully remove the pump cap. But do not fully
remove it and allow a little more residual water
flow into the suitable container.
32
Remove the pump cap.
Remove any loose debris/fluff from inside the pump
and clean the pump. The pump impeller must be
able to rotate. Clean any residual suds or fluff from
the thread of the pump cap and pump housing.
Attach and tighten the pump cap.
Attach and close the cover plate.
To avoid unused detergent from flowing into the
drain during the next wash cycle:
Pour 1 litre of water into chamber II
,,
,,
Select the Draining programme.
Cleaning water inlet
strainers
This necessary if very little or no water flows into
the washing machine.
First release the water pressure in the supply hose:
Turn of the water tap.
Turn the,,programme,, selector
to any,,programme.
,,
(Except Spinning and Draining )
,,
,,
Press the Start button, and allow the programme
to run for approx.40 seconds.
Cleaning the strainer
at the water tap
Disconnect the hose from the water tap.
Rinse the strainer under flowing water.
Reconnect the hose.
33
Cleaning the strainer on the washing machine
Disconnect the hose from the back of the
washer-dryer.
Pull out the stainer and rinse under running water.
Insert the strainer and reconnect the hose.
Turn on the water tap and check whether water is
still discharged. If water is still discharged, check
that the strainer is attached properly.
Turn off the water tap.
Descaling the
washer-dryer
Caution:
Descaling agents contain acids which can attack
parts of the washer-dryer and discolour the laundry.
Provided that you use the correct amount of
detergent, it is not necessary to descale the
washer-dryer. If, however, descaling the appliance
becomes necessary, please follow the instructions
provided by the descaling agent manufacturer.
Frost protection
If the washer-dryer is located in a room which is
exposed to freezing temperatures, any residual
water in both the pump and the water inlet hose
must be drained immediately every time the
machine is used.
Draining the pump:
See Cleaning the pump on page 32,
Draining the water inlet hose:
1. Turn the tap OFF.
2. Unscrew the hose from the tap and hold the
end of the hose over a container.
3. Switch ON any of the washing programmes
for approximately 40 seconds. Water left inside
the inlet hose will be drained out.
4. Screw the hose back onto the tap.
34
Trouble Shooting Minor Faults
! Risk of electric shock
Repairs must only be carried out by our Customer
Service or an authorized technician. If repairs are
needed, and assuming that you cannot eliminate
the fault yourself with the aid the following table:
Turn the programme selector to
,,
,,
Off .
Disconnect the washer-fryer from the mains.
Turn off the water tap.
Call Customer Service.
A signal emitted
in display field
Possible cause
Action
E01
Door not colosed properly.
Check whether laundry is trapped in door;
Close the washer-dryer door.
E02
Tap not turned on.
Inlet hose kinked or pinched.
Filter blocked in water inlet
hose.
Water pressure too low.
Turn the tap on.
Eliminate cause.
Clean filter, see 33.
Lose debris is blocking the
pump;
Drainage pipe blocked
Clean the pump, see page 32;
E04
Eliminate cause.
Clean the drainage pipe.
35
Fault
Possible cause
Action
The washer-dryer door
cannot be opened.
There is water in drum.
Select Draining or Spinning .
Safety function is active.
Wait for 2 minutes.
Detergent residue in the
detergent dispenser.
Detergent was damp or
lumpy.
Clean and dry the detergent
dispenser(refer to Page 31)
The gasket is crimped.
Use the dispensing aid for liquid
detergent.
This may appears after
Remove the transport bolts, operate
installing the transport bolts. the machine for a period of time, the
gasket will return to the original shape.
The belt gets off the pulley.
Too much laundry is in the Put in the laundry well and according
drum or the laundry is put in to the maximum load specifiction.
badly, and close the window
with excessive force.
Control lights do not
come on.
A fuse has triggered.
Power failure.
Switch on/replace the fuse.
Call Customer Service if this fault
is repeated.
An interrupted program will be resumed when power retures. If you
wish to unload the laundry, proceed as in Cleaning the drain pump ,
Page 32.
Plug is loose or not inserted.
The programme
does not start.
Loading door not closed.
Start button does not
pressed.
Check whether laundry is trapped
in door.
Close the loading door(a click should be heard).
Press the Start button.
Press Prewash button
Detergent in chamber I is
not wash away.
Prewash function is
not selected.
Water cannot be seen in
drum.
This is not a fault.
The water lies below the visible part of the drum.
Motor noise
Not a malfunction! It is normal for noises to be heard while the
motor is running.
Pump noise
Not a malfunction! It is normal for noises to be heard from the
pump during the start or the final stage of draining the drum.
Vibrations when
washing and spinning
Transit bolts not removed.
Follow the directions in the installation instructions (page 41)
The machine s feet were
not secured.
Realign the machine using a spirit
level,see the installation instructions.
Water is flowing out from
underneath the machine.
36
The thread of the supply
hose is not tight.
Tighten the thread.
Leak in the drain hose.
Replace the drain hose.
Fault
Possible cause
Action
Foam coming out of the
detergent dispenser.
To much detergent.
Mix1 tablespoon of fabric softener
with 1/2 litre of water and pour
into chamber I of the detergent
dispenser.
Reduce the amount of detergent
next time.
Repeated spinning at short
intervals.
This is not a fault.
The imbalance compensation system is attempting to balance
the load through repeated spins.
Drying programme does
not start.
Drying programme not
selected.
Select the desired dying
programme.
Drying time not set,
or
set drying time is too short.
Set the reasonable drying
time.
Tap not turned on.
Turn on the tap.
Washer-dryer door not
closed properly.
Check whether laundry is
trapped in door.
Close the washer-dryer
door ( click should be heard).
Pump is blocked.
Clean the pump, see page 32
This is not a fault.
The imbalance compensation system is attempting to
balance the load by distributing the laundry more
evenly.
Wash large and small items
together to reduce imbalances.
The foam detection feature
has activated an additional
rinsing cycle to reduce the
amount of foam.
Add a more appropriate amount
of detergent next time.
The degree of dirt was
higher than supposed.
Select a more suitable program.
Not enough detergent.
Add detergent according to the
manufacturer's specifications.
Select Rinsing immediately, or
brush off spots when laundry is
dry.
The programme takes
longer than usual.
Unsatisfactory washing
result.
Detergent residual on the
laundry.
Some phosphate-free
detergents contain
water-insoluble residues
that may appear as light
spots on the laundry.
Grey residues on the
laundry.
Dirt accumulation from
ointments, fats or oils.
Add the maximum amount of detergent and select the highest
permissible temperature next time.
Programme duration changed Not a fault.
during the programme
See also explanations in the chapter programme duration
sequence
from page 9.
37
Customer Service
Before calling the Customer Service, please make
sure that you cannot eliminate the fault yourself.
This is because consultation provided by our
technicians, even within the warranty period, will
lead to costs being incurred by yourself.
Identification
plate
If you cannot correct a problem yourself, switch
off the washing machine, remove the plug from
the socket, shut off the water supply and call
Customer Service. When calling the Customer
Service, please specify the product number
(E-Nr.)of your appliance.
These numbers are shown on the rating plate
which can be found behind the door and also
behind the washing machine.
E-Nr.
Product number
In specifying the product number and production
number of your appliance, your help us in our
attempt to prevent unnecessary travelling and
the associated extra costs.
Technical data:
Rated voltage:220V~
Washing power:200W
Rated frequency:50Hz
Spinning power:460W
Washing capacity:5.2kg
Heating power:1800W
Spinning capacity:5.2kg
Maximum power:2000W
Drying capacity:2.6Kg
Maximum current:10A
Water pressure:0.1~1MPa Water proof :1PX4
38
Programme table
Less ironing
Prewash
Dry
Program duration
in minutes
(approx. time)
**
**
**
**
***
70(110)*
30℃ quick
5.2
39(59)*
40 C
5.2
80(120)*
60 C
5.2
80(138)*
90 C
5.2
95(135)*
2.6
Max 120min
40 C
2.6
60(80)*
60 C
2.6
70(90)*
1.5
Max 120min
Cottons/
coloured
Intensive dry
Easycare
Gentle dry
Chamber
5.2
Chamber II
Cold
Chamber I
Program
Laundry up to(kg)
Extra rinsing
Additional
functions
Intensive stains
Detergent and
fabric softener
Always follow the
manufacture s care
label instructions
,
Silk
30 C
2.0
55(75)*
Wool
30 C
2.0
40(60)*
washing
3.5
20(40)*
rinsing
14
spinning
8
draining
1
,,
duration
,, .
* Time shown in ( ) is the programme
,, Intensive Stains
,,
,, after selecting
** After selecting Extra rinsing or Less ironing or Prewash , the programme = Obligatory
duration will prolong, see page 12.
= optional
****** The following duration is required when you operate the machine according to
the instruction
of user manual (page 21 to 26).The display mode is hour:
,,
minute . The duration will be changed according to the program process. If the
jumping phenomena is occured,it is normal.
39
,,
,,
,,
,,
,,
,,
Programme table: drying
cottons/coloureds (cotton, linen)
Dry weight in Kg
0.5
1.0
1.5
2.5
Drying time selector
Cupboard dry
50-60
60-70
70-80
90
Iron
40-50
50-60
60-70
70-80
Intensive
dry
Easy-care / synthetics
Dry weight in Kg
0.5
1.0
1.5
Programme
selector
Drying time selector
Acrylics
Easy-care
30-35
40-45
25
Times are approximate and refer to standard loads.
The maximum selectable drying time is 120 minutes.
40
50-55
25 - 30
Gentle dry
Installation, Connection and Transport
Safety information
!
Risk of injury
The washing machine is heavy. Take care whenlifting
it.
Caution
Frozen hoses can tear/burst. Do not install the
washer-dryer outdoors or in an area prone to frost.
Take care not to damage the washer-dryer . Do not
hold onto protruding parts (e.g. Loading door ) when
lifting.
In addition to the safety information listed here, the
local water and electricity supplier may have special
requirements.
If in any doubt, have the appliance connected by an
authorized technician.
Before leaving the factory every machine is thoroughly tested under operating conditions any moisture or
residual water which you may find in the machine or
grainage hose are leftover from this testing.
41
On the back of the machine:
- Water drain hose.
- Power cord.
The following tools are helpful:
- Wrench.
- Spirit level.
tools
Dimensions
a=595mm
b=400mm
c=860mm
Approx. weight=68Kg
Installation location
To ensure the proper operation of the washer-dryer,
please pay attention to the following when you install
the machine.
The floor should be solid and flat, never put the
machine on the soft carpet or on the wood floor.
42
Keep the environment dry and vented.
Never put small appliance, such as microwave
oven; and/or jar cooker, on the machine.
Keep the machine away from the flaming equipment, such as candle, cooking stove, liquefied gas
container etc.
Never put the pressure containers on the machine.
Never put the machine over the opening of
uncovered drainage.
In the case of suspended wooden floors, place the
machine on a water-resistant wooden board (plinth)
of at least 30mm thicknees which is screwed to the
floor. If possible, install the machine in a corner of
the room. Secure the machine s feet with brackets
(this applies partcularly to tower arrangements).
,
If the machine is installed on a plinth, the machine s
feet must be secured with brackets to prevent it
sliding when spinning.
,
43
Removing the
transport bolts
The transport bolts must always be removed before
using the appliance for the first time and must be
retained for any subsequent transport (e.g. When
moving) Use the spanner provided only if a ring
spanner is unavailable.
Loosen all four transit bolts with the wrench until
they are freely movable.
If not all parts have been removed and have falled
into the button of the washer-dryer: open the door,
pull the drum forwards slightly, reach in and remove
the parts.
A
B
Insert the covers.
D
C
44
Hose and cable lengths
Left-hand connection
~100cm
max.100cm
~110cm
~110
cm
Right-hand connection
~150cm
max.100cm
~150cm
~140cm
Caution:
In order to avoid siphon, do not put the outlet hose into a
container with water.
Water connection
Water supply
For the water connection a standard cold-water line
with a minimum water pressure of 0.1MPa is required
(with tap full ON, at least 8 litres of water must flow
out in one minute). If the water pressure exceeds
1MPa, a pressure reducing valve must be added.
Never connect the machine to the mixer tap of a
pressureless hot-water heater.
Caution! Connections are under full water
pressure, check for leaks with tap turned fully ON.
45
The filters at the free end of the inlet hose and at
the back of machine should only be removed for
cleaning purposes.
To avoid water damage, the tap must be turned
OFF after using the machine.
The plastic nuts on the hose connections must
only be tightened by hand.
For tight connection between washer-dryer and
water source, you can:
G 1/2
1. Call Customer Service before you install the
machine, get the plastic connector freely. It may
connect tightly the water inlet pipe and your water
tap.
Plastic connector
CS code 424387
2. Or you may purchase the specific water tap from
customer service. It is designed by factory. It may
be better connected with machine than your water
tap.
Note: The water tap is not free.
Water tap
CS code 184611
Caution:
Do not disassemble the water inlet hose frequently, the untight connection will lead to leakage. We
suggest that you use a water inlet hose specially
for the washer-dryer.
If you need lengthen the water inlet hose together
with the machine, please contact local ASS center/
station or leader to buy additional lengthening hose.
Additional lengthening water inlet hose is not free.
46
Water Drainage
Caution
Do not bend or pull the water drainage hose.
Height between the placement area and drainage
point: maximum 100cm.
Drainage into a wash basin( The hose elbow is in
the drum).
Caution
The plug must not block the drain of the wash basin.
Secure the water drainage hose so that it does
not slide out.
When water is being drained, check that the water
flow is fast enough.
Leveling procedure
All four appliance feet must be firmly on the ground.
The washing machine must not wobble
Level the washer-dryer with the assistance of the four
adjustable feet and a spirit level.
Loosen the counter-nut 1 using the wrench.
Adjust the height by means of turning the appliance
foot 2.
Tighten the counter-nut 1.
47
Electrical connection
When heating, the maximum current of the washerdryer is 10A, so please make suer that the power
supply system (voltage, current and cable) is applicable to the load of theapplied appliance.
The machine must only be connect to an alternating current supply via a correctly installed earthed
socket.
The voltage indicated on the rating plate at the
back of the machine must match the mains voltage
at the installation location.
Connected load and required fuse or line protecting cut-out are indicated on the rating plate.
It must be ensured that the plug and socket match,
that the conductor cross-section is sufficient and
that the earthing system has been installed in
compliance with regulations.
Multiple plug connectors and extension cables
must not be used.
Do not connect the machine to electrical outlets
while your hands are wet or damp.
To remove the plug from the socket, grasp the
plug firmly and pull it out. Do not pull at the cable.
If the supply cord is damaged, it will be replaced
by a special cord or a assembly available from
the manufacturer or its service agent.
In the event that an earth-leakage circuit breaker is
to be used, only use types marked with the following symbol:
. Only this symbol can guarantee
compliance with all current regulations.
48
Transport e.g.
when moving
Before transporting the washer-dryer:
- Turn off the water tap,
- Drain any residual washing solution (refer to
Page 32),
- Release the water pressure in the supply hose
(refre to Page 33),
- Disconnect the washer-dryer from the mains,
- Dismantle the supply and drainage hose,
- Install the transport bolts.
- Having transported the appliance and ensured
proper installation and connection, allow the
Draining programme to run through before
starting the first wash programme.
Preparing and inserting
the transport bolts
Remove the covers.
Preparing the transit bolt(see picture: page 44):
Pull the bolt out of the sleeve until the end of the
bolt is flush with the end of the sleeve.
Insert and tighten the bolts.
The lug on the washer must be located in the
groove in the rear panel of the housing.
49
Appendix
You can change the volume of the buzzer according
to your requirement.
The operation procedure:
1. Switch on the machine,turn the program selector
,,
to Off .
,,
Adjust the volume
of buzzer and audible
feedback of Start
button
,,
2. Turn the program selector to cold Easy-care ,
press ,,the additional function button Intensive
,
stains and don t loose, you can hear the volume
of the buzzer from minimum to maximum to off
cycled. If you decide the volume that you wanted,
loose your finger.
,,
,,
,,
3. Finally,turn the program selector to Off . If
necessary,select other programs by turning
the program selector after several seconds.
,,
4. If the volume of buzzer has been opened,you
can hear the audible feedback as,, same volume
as buzzer when you, press Start button. If be
not opened,you can t hear the voice.The operation may check if the volume of buzzer has
been opened.
,,
50
Appendix
You can open or close the audible feedback of
function buttons according to your requirement.
Open procedure:
1. Switch on the machine,turn
the programme
,,
selector to Off .
2. Press ,,two additional function buttons Intensive
,
,,
stains and Extra rinsing and don t loose.
3. Turn the programme selector to cold Cottons/
,,
coloureds programme, you can hear a voice quiet
long. It means that you have opened the sound
feedback of function buttons,loose your fingers
on the buttons.
,,
4. Finally,turn the programme selector to Off . If
necessary,select other programmes by turning the
programme selector after several seconds.
,,
,,
,,
,,
,,
When you select additional function(s) later you
will hear a voice quiet long from the buzzer;when
you cancel additional function(s) you will hear a
voice quiet short from the buzzer.
Close procedure:
1,2 and 4 are same as open procedure.
3. Turn the programme
selector to Cold Cottons/
,,
coloureds programme, you can hear a voice quiet
short. It means that you have closed the sound
feedback of function buttons, loose your fingers
on the buttons.
,,
! You can adjust the volume of audible feedback.
The operation procedure
,, refer to Page 50 Adjust
the volume of buzzer .
,,
Audible feedback
of function buttons
51
Contents of this brochure could be changed without written notice.