Braeburn 5300 Specifications

1 Specifications cont.
Premier Series
Universal Auto Changeover
Up to 2 Heat / 2 Cool
5300
Conventional and Heat Pump Thermostat
Installer Guide
Before Installing, Programming or Operating,
PLEASE READ ALL INSTRUCTIONS
1 Specifications
5 Testing Thermostat
2 Installation
6 Wiring Diagrams
3 Quick Reference
4 Programming Installer Settings
SEE USER MANUAL FOR TROUBLESHOOTING
WARNING
Important Safety Information
• Always turn off power to the air conditioning or heating system prior to
installing, removing, cleaning or servicing thermostat.
• This thermostat is a dual power thermostat and either requires 24 Volt
AC Power or two (2) properly installed “AA” Alkaline batteries for normal
operation and control of the heating or cooling system.
• Properly installed batteries will allow the thermostat to retain clock settings
in the event of loss of AC Power due to power outage or rolling
blackouts when used as a hardwired thermostat.
• This thermostat should only be used as described in this manual. Any other
use is not recommended and will void the warranty.
1 Specifications
• Electrical Rating: 24 Volt AC (18-30 Volt AC)
1 amp maximum load per terminal
3 amp maximum load (all terminals)
• Control Range: 45º - 90º F (7º C - 32º C)
• Accuracy: +/- 1º F (+/- .5º C)
• AC Power: 18-30 Volt AC
• DC Power: 3.0 Volt DC (2 “AA” Alkaline batteries included)
© 2006 Braeburn Systems LLC • Patents Pending • All Rights Reserved. Pub. No. 5300-100-003
• Compatibility: Compatible with low voltage single stage or multi-stage heat/cool
systems, including heat pumps with up to two stages of heating and two stages
of cooling. This thermostat can also be used on 250mv to 750mv millivolt heating
only systems.
• Terminations: R, Rc, O, W1/E, B, Y2, W2, Y1, G, C, L, S1, S2
2 Installation
Replacing Existing Thermostat
Most existing thermostats have three parts:
• The cover, which may snap or hinge over the existing thermostat.
• The electronics or body, which controls the existing system.
• The sub-base, where the wires attach through the wall to the existing system.
1. Always turn off power to the air conditioning and heating system prior to
removing existing thermostat.
2. Carefully remove the cover and electronics body from the old thermostat
sub-base. Depending on the brand, these parts may pull off or need to be
unscrewed. The old sub-base should remain wired and on the wall until
steps 4 and 5.
3. Label every old wire with the letter of the connection to which the wire is
attached. Example letters are R, M, Y, etc. Depending on the brand of the
old thermostat, your letters may be different.
4. After labeling the old wires, loosen each connection and remove them from
old sub-base. Secure the wires to prevent them from slipping into the opening
in the wall.
5. Remove the old sub-base from the wall, again being careful that the wires do
not slip into the opening in the wall.
6. Use the chart below to determine the new thermostat connections. As an
example, if the old thermostat had a G or F connection, it goes to G on the new
thermostat. It may be helpful to use the chart by circling (with a pencil or pen)
the letter of each wire removed from the old thermostat.
NOTE: This thermostat is designed for use on low voltage 24 volt AC single stage
or multi-stage systems, including heat pumps with up to two stages of heating
and two stages of cooling. Do not use this thermostat on systems with voltage
higher than 30 Volts AC. This thermostat requires a transformer common wire for
proper installation if used as a hardwired thermostat.
Old Terminal from
Existing Thermostat
R, V-VR or VR-R
O or R
E/W1
B
Y2
W1, W2 or W-U
Y, Y1 or M
G or F
C, X or B
L or X
S1
S2
New Terminal for
New Thermostat
R
Rc
Terminal Description
24 Volt AC
24 Volt AC (Cooling for Dual
Transformer Systems)
Reversing Valve (Cooling)
1st Stage Heating for
Conventional Systems or
Emergency Heating for 2 Stage
Heat Pumps
Reversing Valve (Heating)
Stage 2 Compressor
Stage 2 Heating
Stage 1 Compressor
Fan Control
24 Volt AC, Transformer Common
System Monitor
Optional Remote Sensor
Optional Remote Sensor
O
E/W1
B
Y2
W2
Y1
G
C
L
S1
S2
1
2 Installation cont.
3 Quick Reference
Installing New Thermostat
Inside of model 5300 shown
NOTE: When installing this thermostat in a new location, following a few simple
guidelines and the applicable building codes will give the best results. Install the
thermostat in a location that provides good airflow by avoiding areas behind
doors, near corners, air vents, direct sunlight or heat generating devices. The
wiring must conform to all building codes and ordinances as required by local
and national code authorities having jurisdiction for this installation.
1. Always turn off the power to the air conditioning and heating system prior
to installing this thermostat.
2. Locate the release latch on the bottom (not the back) of the thermostat.
Press the release latch in and separate the body from the sub-base of
the thermostat.
3. Set the thermostat electronics and cover down on a clean surface. Place the
sub-base on the wall in the desired location.
4. Using the slotted mounting holes in the sub-base, mark the placement of the
mounting holes through the slots and onto the wall. Ensure the wires come out
of the wall into the center hole of the sub-base.
5. After verifying the drill will not damage items in the wall, use a 3/16 drill to
create the mounting holes. Gently tap the supplied plastic anchors into the
holes in the wall.
6. Place the thermostat sub-base against the wall in the desired location. Ensure
the thermostat is level, the wires are inserted in the opening, and the mounting
holes are aligned with the slots on the sub-base.
7. Fasten sub-base to wall using supplied screws into the plastic wall anchors.
8. Connect wires to the quick wiring terminal blocks. Use the wiring diagram
chart to ensure the old and new connections are correct.
9. To prevent electrical shorts and potential damage to the thermostat, make
sure all wire connections are secure and not touching each other.
10. Locate the thermostat body, and ensure the cover is still installed properly.
Using the mounting tabs on the top of the sub-base as a guide or hinge, close
up the thermostat case by pivoting the body and cover closed. The latch on the
bottom of the thermostat will click when the case is properly closed.
11. Flip the front thermostat cover up and open the battery compartment door.
12. Locate the positive [+] ends of the batteries and match them with the positive
[+] terminals located in the battery compartment. Install the two new “AA”
alkaline batteries (supplied). Close battery compartment door.
13. Restore system power and proceed to programming and system checkout.
2
8
10
9
7
1
6
2
3
4
5
SYSTEM Button: Selects AUTO (Heat/Cool), COOL, OFF, HEAT or EMER.
PROG Button: Program setup mode, selects set point time, temperature
and fan setting for each program.
3 HOLD Button: Enables extended hold, clears extended hold or
temporary override.
4 RETURN Button: Scrolls between installer setup screens, or returns unit
to the normal mode from program mode.
5 DAY/TIME Button: Selects hour, minute and day setting. Selects program
day in program setting mode.
6 FAN Button: Selects AUTO, ON, CIRC (recirculate) and PROG (program) modes.
7 RESET Button: Located on front of thermostat, will return programming,
clock, differential settings, filter check monitor, adjustment limit from set
point, keypad lock, temperature hold, short cycle timer and recirculating fan
to default settings if previously programmed.
8
Button: Turns on backlight for 10 seconds.
9
Button: Increases setting (time, temperature, etc.). Scrolls between
option settings.
10
Button: Decreases setting (time, temperature, etc.). Scrolls between
option settings.
4 + 2 RETURN and PROG Buttons: When pressed at the same time, returns
unit to the normal mode from Installer setup option mode.
4 + 9 RETURN and
Buttons: Installer setup option mode is entered when
holding the RETURN and buttons together for 3 seconds.
CLEAR Button: Located on back side of circuit board, resets thermostat
to all factory defaults.
1
2
3
4 Programming Installer Settings
Default Thermostat Settings
At initial power up or after Installer CLEAR is pressed, the thermostat is reset to
factory defaults. Installer CLEAR is located on the circuit board.
Function
Status after Clear
Operation mode
Temperature hold
Fan Switch
Clock
Room temperature display
OFF, Auto Changeover enabled
Permanent and temporary hold cleared
AUTO
12:00 pm, Monday
70° F (21.0° C), to be renewed within
5 seconds
Set point temperature
62° F (17.0° C) for Heat, Emergency
Heat and Off 83° F (28.0° C) for Cool
Temperature scale
Fahrenheit
Operating program
DAY program, Monday
Low-battery warning
Off, to be renewed within 5 seconds
AC interrupted warning
Off, to be renewed within 5 seconds
1st stage differential
.5° F (0.2° C)
2nd stage differential
2° F (1.0° C)
Programming
7 Day, 4 Event
Deadband
3° F
Residual Cooling Fan Delay
60 seconds
Short cycle protection timer
On, 5 minutes, Reset
Adaptive Recovery Mode
ON
Output relays
All turned off
Recirculating Fan
Timer reset, with 24 min OFF, 12 min ON,
Lock OFF
Extended Hold
Long (indefinite)
Filter Check Monitor
0 days-No Warning, Timer reset
Keypad Lock
Complete (level 2), unlocked,
555 universal code
System type
Conventional, Single Stage
1st Stage Heat Fan Control
Gas
2nd Stage Heat Fan Control
Electric
Fossil Fuel Compressor Lock
Off
Auto Changeover
Enabled
Compressor Outage Protection Off, Timer reset
Temperature Sensor
Internal
12 / 24 Hour Clock
12 hour
Adjustment Limit from Set point 0, OFF
AC Interrupt Warning Mode
OFF
User Profile
Residential
4 Programming Installer Settings cont.
When the User RESET button (on front of thermostat) is pressed, the following
options will reset to the factory defaults. All other settings are saved when the
RESET button is pressed.
Function
Status after Reset
Programming
Default setting depending on
programming mode setting (see User
Manual). For manual mode: Heat - 62° F,
Cool - 83° F.
12:00 pm, Monday
.5° F (0.2° C)
2° F (1.0° C)
Clock
1st stage differential
2nd stage differential
(if configured for Multi-Stage)
Filter Check Monitor
Adjustment Limit from Set point
Keypad Lock
Temperature Hold
Short Cycle Timer
Recirculating Fan
0 days-No Warning
0, OFF
555 universal code or last code entered
Permanent and temporary hold cleared,
reset to Long Hold
Reset
Timer reset, 24 minute off cycle.
With recirculating lock set, fan state
defaults to CIRC.
Setting Thermostat Installer Options
The Installer Options section allows the system and programming parameters
to be set up at installation. The Installer Options mode is menu driven. As the
different options are programmed you may eliminate specific options. For example,
if the system is set to single stage heat pump, Option 8, selecting the first stage
fan control will no longer be available.
The Installer Option mode is entered by holding the RETURN and buttons
together for 3 seconds. Installer Option 1 Residential or Commercial will be
displayed. Pressing the or buttons will scroll between choices. To scroll to
the next installer option, press the RETURN button. The thermostat will return to
normal operating mode after the last Installer Option mode has been set or by
pressing the RETURN and PROG buttons at the same time.
NOTE: The thermostat will return to normal operating mode automatically after
30 seconds if no key is pressed.
NOTE: Any changes to Installer Option 7 (System Type) will cause Options 8, 9, 10,
11 and 12 to reset to the default values that are dependent on system selection.
4
5
4 Programming Installer Settings cont.
Installer Options
1 – Residential or
Commercial
2 – Programming
Mode
3 – 12/24 Clock
Factory Default Options
aes
aes, bus
pao67
12h
4 – Temperature Scale de6F
5 – Auto Changeover
autoON
6 – Dead Band
band 3
7 – System Type
11C
8 – First Stage
Fan Control
1H6
9 – Second Stage
Fan Control
2HE
10 – Fossil Fuel
Backup Option
auh AE
11 – AC Power
off-AC
Interrupt Warning
12 – Compressor
Power Outage
Protection
cpopOFf
13 – Short Cycle
Protection
cscp 5
14 – Residual Cooling
Fan Off Delay
fan60
15 – Recirculating Fan ciacOFf
Lock
16 – Enable / Disable aec ON
ARM™
17 – Set Sensor
Control
sens1
18 – Set Security Level sec 2
for Keypad Lock
Comment
Selects a Residential or
Commercial (BUS) profile.
pao67,
Not available if thermostat
pao6 52,
is in the Commercial
pao6NO
(BUS) profile.
12h, 24h
Selects either 12 hour or
24 hour clock.
de6F, de6C
Selects either Fahrenheit
or Celsius.
autoON,
Either enables or disables
autoOFf
Auto Changeover.
band 2, band 3, Selects Auto Changeover
band 4,
Dead Band of 2, 3, 4 or 5º F
band 5
(1.5, 2.0, 3.0º C), if Auto
Changeover is enabled.
11C, 22C,
Selects single stage
11HP, 22HP
conventional, 2 stage conventional,
single stage heat pump, or 2 stage
heat pump.
1HG, 1HE
Not available with a heat pump
system. Selects between 1st
stage gas or electric heat.
2HE, 2H6
Only available with a 2nd stage
heat pump system. Selects
between 2nd stage gas or
electric heat.
auh AE,
Only available with a 2nd stage
auh A6
heat pump system. Locks out 1st
stage during 2nd stage heat call
for fossil fuel backup systems
(AUXAG). With an electric backup
system (AUXAE) both stages
will run.
off-AC,
Only available when thermostat is
on-AC
installed as a hardwired unit.
Select between turning the AC
power interrupt warning off or on.
cpopOFf,
Only available with 2nd stage heat
cpopON
pump and AC power connected.
Select between compressor lock
off and compressor lock on.
cscp 5, cscp 4, Selects 5, 4, 3, 2 or 0
cscp 3, cscp 2, minutes for the compressor
cscp 0
short cycle protection.
fan00,
Selects 0, 30, 60 or 90 seconds as
fan30,
the time the fan will stay on after
fan60,
the cooling system has satisfied
fan90
the set point temperature and has
turned off the compressor.
ciacOFf,
Selects between Recirculating
ciacON
Fan Lock off or on.
aec ON,
Enables or disables ARM™.
aec OFf,
Not available in nonprogrammable mode.
sens1,
Selects between Internal,
sensE,
External and Averaging sensor
sensA
control. This is only available if
the remote sensor is connected.
sec 1,
Selects between level 1 or level
sec 2
2 keypad lockout.
6
4 Programming Installer Settings cont.
1. Selects Residential or Commercial (BUS) profile. Determines programming
events per day. If Residential is selected, 4 events per day are available. If
Commercial is selected, 2 events per day are available. Only the 7 day
programmable mode is available for the Commercial profile.
2. Selects the programming mode, either full 7 day or 5-2 day (weekdayweekend) programming or non-programmable. If the Commercial profile was
selected in step 1 this option is not available.
3. Selects either a 12 hour or 24 hour clock.
4. Selects preferred temperature scale of either ºF or ºC.
5. Selects either Auto Changeover on or off. When off is selected, the AUTO icon
will not be displayed when selecting the system options with the system switch.
When Auto Changeover mode is enabled and selected, the system automatically
switches between heating and cooling when the room temperature meets the
programmed heating or cooling set points.
6. When Auto Changeover mode is enabled and selected, the system automatically switches between heating and cooling when the room temperature
meets the normal criteria for either a heating or cooling call. There is a forced
separation (dead band) between the heating and cooling set points, so the
systems do not work against each other. This option selects Auto Changeover
Dead Band of 3, 4 or 5º F (1.5, 2.0, 3.0º C) the default is 3º F.
7. Selects single stage conventional (11C), 2 stage conventional (22C), single
stage heat pump (11HP), or 2 stage heat pump (22HP). Any change made to
the system type resets Installer Options 8 through 12 to their default values
dependent on system selected.
8. Selects between 1st stage gas or electric heat. This Installer Option is not
available with a heat pump system.
9. Selects between 2nd stage gas or electric heat. This Installer Option is only
available with a 2 stage heat pump system.
10. For heat pump units with an electric auxiliary stage, both the first and second
stages of heating will run when a call for second stage heat is made. For heat
pump units with a fossil fuel auxiliary stage, the first stage will be locked out
one minute after a second stage heat call, and the second stage will only
be used.
11. Select between turning the AC power interrupt warning off or on. During a
power loss, the thermostat will display an outage warning. The system clock
will continue to run, and all settings will be maintained until the outage period
is over. This Installer Option is only available when thermostat is installed as a
hardwired unit.
12. This thermostat provides cold weather compressor protection by locking out
the compressor stage (1st stage) of heating for a period of time after a power
outage greater than 60 minutes. The lockout period is one hour less than the
outage time, up to a maximum of 12 hours. During that period of time, the
auxiliary heat stage will still be available to maintain the set point temperature.
The compressor lockout can be disabled by setting this option to OFF.
13. This thermostat includes an automatic compressor protection feature to avoid
potential damage to the cooling system from short cycling. This thermostat
automatically provides an adjustable delay after turning off the cooling system
output to protect the compressor. This protection is also present in the heat
mode of operation on single stage heat pump systems to protect the compressor.
(continued on page 8)
7
4 Programming Installer Settings cont.
14. During the COOL mode of normal operation the fan will stay on for 60 seconds
after the cooling system has satisfied the set point temperature and has turned
off the compressor. This allows the system to provide higher efficiency during
cooling operation.
15. The Recirculating Fan can be “locked on”, so that the only fan selections
available to the user are CIRC and ON. The Recirculating Fan Mode provides
more even temperature distribution and improves indoor air quality by
circulating air through the furnace filtration system more often. By locking the
Recirculating Fan on, the user will only have the option to run the fan all the
time (ON) or use the Recirculating Fan Feature (CIRC). If the Recirculating Fan
lock is not set to on, the thermostat is put into the Recirculating Fan Mode by
pressing the FAN button until the CIRC icon is displayed. If no call for heating
or cooling occurs within the fan off cycle set in the User Options (see User
Manual), the fan will run for 12 minutes. The highest setting, 120 minutes,
will run the fan least often – 9% minimum running time. The lowest setting,
24 minutes (factory default), will run the fan most often – 33% minimum
running time. The Recirculating Fan feature is available in the COOL, OFF,
HEAT, or EMER mode.
16. Enables or disables the ARM™ feature. During ARM™, room temperature is
recovered gradually by turning on the heating or cooling before the end of the
set back period. In a multi-stage configuration, room temperature is recovered
gradually by using only the first stage heating or cooling until the last 20
minutes, to minimize the use of the 2nd stage heating or cooling. The set point
temperature is changed to that of the upcoming comfort program temperature.
ARM™ does not operate when the unit is in the temporary or permanent HOLD
mode if the program is temporarily overridden or if emergency heat is selected
for multi-stage heat pumps. If the ARM™ feature is disabled the thermostat
will recover the set point temperature at the programmed set point time after
the setback period ends.
17. If the remote sensor is connected during installation, you must select between
internal, external and averaging remote sensor control.
18. The keypad lockout feature has two levels of security. Level one locks all
buttons (including the reset) except for the , and backlight buttons. Level
2 locks the entire keypad except the backlight button. The and buttons
can be pressed together to enter the lock code but the buttons do not work
individually to adjust the temperature. The lock level is set during the Installer
Options and the lock code is set in the User Options. See the User Manual,
Section 2.
NOTE: Any changes to Installer Options 1 through 6 will cause all User Options
and Programming to reset to their default values if the User Options were
previously programmed. See User Manual, Section 2.
8
5 Testing the Thermostat
WARNING!
Read BEFORE Testing
• Do not short (or jumper) across terminals on the gas valve or at the heating or
cooling system control board to test the thermostat installation. This could
damage the thermostat and void the warranty.
• Do not select the COOL mode of operation if the outside temperature is below
50º F (10º C). This could possibly damage the controlled cooling system and
may cause personal injury.
• This thermostat includes an automatic compressor protection feature to avoid
potential damage to the cooling system from short cycling. The default is to
provide a 5-minute delay after turning off the cooling or heating output to
protect the compressor. This default can be changed in Section 4, Programming
Installer Options.
NOTE: Test your thermostat prior to programming any user settings. Pressing the
Installer CLEAR button will reset the thermostat to all factory defaults. Pressing
the User RESET button will erase programming, clock, differential settings, filter
check monitor, adjustment limit from set point, keypad lock, temperature hold,
short cycle timer and recirculating fan if previously programmed. This will return
all User Options to their default values.
1. Scroll through system settings on the left side of the display to HEAT.
2. Press the button on the keypad until the set point temperature setting is a
minimum of 3 degrees higher than the current room temperature. The heating
system should start within several seconds. The fan may not turn on immediately due to the heating system built-in fan delay.
3. Scroll through system settings to OFF. The heating system should stop within
several seconds.
4. Scroll through system settings to COOL.
5. If the compressor has previously been running, then you must wait 5 minutes,
or until the installer programmed delay set in Section 4, Option 13, for the
automatic compressor short cycle protection period to expire. You can also
press the RESET button to bypass this feature for initial testing purposes.
Pressing the RESET button will erase programming, clock, differential settings,
filter check monitor, adjustment limit from set point, keypad lock, temperature
hold, short cycle timer and recirculating fan if previously programmed. This will
return all user options to their default values.
6. Press the button on the keypad until the set point temperature is a minimum
of 3 degrees lower than the current room temperature.
7. The cooling system should start within several seconds. Scroll through system
settings to OFF. The cooling system should stop within 90 seconds (dependent
on the setting of the Residual Cooling Fan Feature).
8. Scroll the fan settings to ON, the system blower should start.
9. Scroll the fan settings to AUTO, the system blower should stop.
9
6 Wiring Diagrams
Heat Pump Systems
(See Note 5)
R
RC
O
W1 / E
B
W2
2nd Stage
Compressor
Control
(Note 2)
Emergency
Heat Control
(See note 4)
Reversing Valve
(Active in
Cooling-See
Note 3)
Y2
Reversing Valve
(Active in
Heating-See
Note 3)
Y1
G
1st Stage
Compressor
Control
2nd Stage
Heat Control
(Note 2)
C
L
S1
S2
NOTES:
1. Transformer Common connection not required for battery-only operation
of thermostat.
2. Second Stage Control connections not used for single stage heating or
cooling systems.
3. For units requiring reversing valve to be energized during heating, connect
reversing valve to B terminal.
For units requiring reversing valve to be energized during cooling, connect
reversing valve to O terminal.
4. Required for units with 2 stage heat only.
5. For 2 stage heat units not having a separate Emergency Heat Terminal, add
installer supplied jumper.
NOTES:
1. Transformer Common connection not required for battery-only operation
of thermostat.
2. Second Stage Control connections not used for single stage heating or
cooling systems.
3. For millivolt or other 2-wire heating systems, connect 2 wires from heating
control to R and W1.
NOTES:
1. Transformer Common connection not required for battery-only operation
of thermostat.
2. Second Stage Control connections not used for single stage heating or
cooling systems.
System
Malfunction
Indicator
Fan Control
Transformer Common
(See Note 1)
This model 5300
never requires an
R to RC Jumper.
Remote
Sensor
(Optional)
Neutral
24 VAC
120 VAC
Hot
Conventional Systems (Single Transformer)
R
RC
O
W1 / E
B
Y2
W2
2nd Stage
Compressor
Control
(Note 2)
Y1
C
1st Stage
Compressor
Control
2nd Stage
Heat Control
(Note 2)
1st Stage
Heat Control
G
L
Transformer Common
(See Note 1)
This model 5300
never requires an
R to RC Jumper.
Fan Control
S1
S2
Remote
Sensor
(Optional)
Neutral
24 VAC
120 VAC
Hot
Single Stage Conventional Systems (Dual Transformer)
RC
O
W1 / E
B
Y2
W2
Y1
G
1st Stage
Compressor
Control
1st Stage
Heat Control
Fan Control
C
L
Transformer Common
(See Note 1)
R
S1
S2
Remote
Sensor
(Optional)
Neutral
24 VAC
120 VAC
Hot
Neutral
24 VAC
120 VAC
Heating
Hot
Cooling
10
11
12
5
YEAR
LIMITED
WARRANTY
Store this
booklet for
future reference
Braeburn Systems LLC, as an Energy Star partner
has determined that this product meets the Energy Star
Guidelines developed by the U.S. Environmental
Protection Agency & the U.S. Department of Energy for
maximum energy efficiency.
For more information on energy
savings, go to www.energystar.gov
Braeburn Systems LLC warrants each new Braeburn thermostat against any defects that are
due to faulty material or workmanship for a period of five years after the original date of
purchase by a professional service technician. This warranty and our liability does not apply to
batteries, nor does it include damage to merchandise or the thermostat resulting from
accident, alteration, neglect, misuse, improper installation or any other failure to follow
Braeburn installation and operating instructions.
Braeburn Systems LLC agrees to repair or replace at its option any Braeburn thermostat
under warranty provided it is returned postage prepaid to our warranty facility in a padded
carton within the warranty period, with proof of the original date of purchase and a brief
description of the malfunction. This limited warranty does not include the cost of removal or
re-installation.
This warranty gives you specific legal rights and you may also have other rights that vary from
state to state or province to province. Answers to any questions regarding our limited warranty
may be obtained by writing our corporate offices.
WARRANTY FACILITY: Braeburn Systems LLC
Attn: Warranty Department
2215 Cornell Avenue
Montgomery, IL 60538
Braeburn Systems LLC
2215 Cornell Avenue • Montgomery, IL 60538
Technical Assistance: www.braeburnonline.com
Call us toll-free: 866-268-5599 (U.S. Only)
630-844-1968 (Outside the U.S.)
© 2006 Braeburn Systems LLC • Patents Pending • All Rights Reserved. Made in China • 5300-100-003