Eci Telecom B-FOCuS 312 User guide

B-FOCuS
Router 312+
User Guide
http://www.ecitele.com/b-focus
B-FOCuS Router 312+
User Guide
© Copyright by ECI Telecom 2005. All rights reserved worldwide.
The information contained in this document is proprietary and is subject to all relevant
copyright, patent, and other laws protecting intellectual property, as well as any specific
agreement protecting ECI rights in the aforesaid information. Neither this document nor the
information contained herein may be published, reproduced or disclosed to third parties, in
whole or in part, without the express, prior, written permission of ECI. In addition, any use of
this document or the information contained herein for any purposes other than those for which
it was disclosed is strictly forbidden.
ECI reserves the right, without prior notice or liability, to make changes in equipment design or
specifications.
Information supplied by ECI is believed to be accurate and reliable. However, no responsibility
is assumed by ECI for the use thereof nor for the rights of third parties, which may be affected
in any way by the use thereof.
Any representation(s) in this document concerning performance of ECI product(s) are for
informational purposes only and are not warranties of future performance, either express or
implied. ECI standard limited warranty, stated in its sales contract or order confirmation form,
is the only warranty offered by ECI in relation thereto.
This document may contain flaws, omissions, or typesetting errors; no warranty is granted nor
liability assumed in relation thereto unless specifically undertaken in ECI sales contract or
order confirmation. Information contained herein is periodically updated and changes will be
incorporated into subsequent editions. If you have encountered an error, please notify ECI. All
specifications are subject to change without prior notice.
ECI Telecom Ltd. Proprietary
ii
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
User Guide
Table of Contents
1
Introduction ....................................................................... 1
1.1 Package Contents ..................................................... 1
2
Hardware Installation........................................................ 2
3
Basic Software Configuration.......................................... 3
3.1 Logging In to Your Router.......................................... 3
3.2 Setting Up a Connection............................................ 5
4
Safety Considerations ...................................................... 7
5
Buttons and LEDs ............................................................. 8
5.1 Buttons/Ports ............................................................. 8
5.2 LED Descriptions ....................................................... 9
5.3 LED Table................................................................ 10
6
Troubleshooting.............................................................. 11
6.1 The Router is not Functional.................................... 11
6.2 The ADSL Link LED Blinks but Does Not Go Solid . 12
6.3 The DSL Link LED is Always Off ............................. 12
ECI Telecom Ltd. Proprietary
iii
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
ECI Telecom Ltd. Proprietary
User Guide
iv
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
1
User Guide
Introduction
Thank you for choosing ECI Telecom’s B-FOCuS 312+ Router as your gateway
to the world of fast Internet. Your new router is a state-of-the-art unit that
includes an ADSL router and an advanced router, enabling you to create and
connect a network of computers to a single ADSL line. Your router also
provides a powerful firewall that will secure your home network and computers
from unwelcome intrusions.
1.1
Package Contents
Please check that your package contains the following items.
Table 1. B-FOCuS 312+ Package Contents
Item
Equipment
Description
Quantity
1
B-FOCuS 312+ router
1
2
AC power adaptor 12V,
1A
1
3
RJ-45 cable for
connecting router to
computer via 10/100
base-T Ethernet port
1
4
RJ-11 cable for
connecting to the ADSL
line
1
ECI Telecom Ltd. Proprietary
1
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
2
User Guide
Hardware Installation
The following diagram and explanations will help you install your router.
Figure 1. B-FOCuS 312+ Router Connection Diagram
To connect your router
1. Connect one end of the RJ-45 Ethernet cable to a LAN port on your
router and the other end to the LAN port of one computer.
2. Connect one end of the RJ-11 telephone cable to the ADSL port on the
back of your router and connect the other end to the ADSL port on the
phone line splitter.
3. Connect the AC power adapter. Only use the power adapter supplied
with the router.
4. Turn on the power and proceed to Section 3, Basic Software
Configuration.
ECI Telecom Ltd. Proprietary
2
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
3
User Guide
Basic Software Configuration
In order to connect to your service, you must set up your router as described in
this section.
3.1
Logging in to Your Router
To open the configuration options of your router, use your Internet browser.
To log in to your router
1. Open your Internet browser and type 10.0.0.138 in the address bar.
The Log In window is displayed.
2. Enter the username Admin and password Admin.
Note: The username and password are case-sensitive.
3. Click Log In. The Home Page window is displayed.
If you are unable to open the Configuration utility, perform the following
steps.
a. From the computer desktop, select Start > Settings > Network
and Dial-up Connections > Local Area Network. To restart
your network card, click Disable and then restart the network
card. Try again to log in to the configuration utility.
ECI Telecom Ltd. Proprietary
3
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
User Guide
b. If you are still unable to connect to the configuration utility, then
from your Internet browser, select Tools > Internet Options and
click Delete Cookies, Delete Files, and Clear History. Try again
to log in to the configuration utility.
4. Click the Setup tab.
You have logged in to the configuration utility and are now ready to configure
your router.
ECI Telecom Ltd. Proprietary
4
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
3.2
User Guide
Setting Up a Connection
To set up a new connection
1. From the Setup window, click New Connection. The Connection Setup
window is displayed.
2. Give your new connection a name.
Note:
Any name is legal, for example, the name of your service
provider, but you may not use spaces or special
characters.
3. In the Options section, it is recommended to enable NAT and Firewall in
order to protect your network from intrusions.
4. Configure the parameters for the network.
ECI Telecom Ltd. Proprietary
5
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
User Guide
For the connection Type, select according to your network type, for a
home network, choose PPPoE.
In the PVC Settings section, in the VPI box, type 8. In the VCI box, type
35.
5. Click Apply.
6. To save the changes, click the Tools button (at the top of the page) and
select System Commands. From the System Commands page, click
Save All.
7. To make the changes effective, click the Tools button (at the top of the
page) and select System Commands. From the System Commands
page, click Restart. The Restart Confirmation message box is displayed.
8. Click OK.
You have completed the basic software configuration for your router. The router
will restart after a few seconds and connect to the Internet. Open your browser
and enjoy surfing the net.
If you are unable to connect to the Internet, see Section 6, Troubleshooting.
ECI Telecom Ltd. Proprietary
6
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
4
User Guide
Safety Considerations
The B-FOCuS 312+ Router is designed for in-house desktop use only.
Therefore:
• Do not expose to direct sunlight.
• Do not expose to temperatures exceeding 40°C.
• Do not immerse in water, and do not dampen or install in wet conditions.
ECI Telecom Ltd. Proprietary
7
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
User Guide
5
Buttons and LEDs
5.1
Buttons/Ports
This section describes the ports and buttons on the router.
ADSL
Port
LAN
Port
Reset
Button
Power
On/Off
Button
Figure 2. B-FOCuS Router 312+ Back Panel
• Reset Button. To reset the router, press and release the Reset button;
after about 30 seconds the unit will become operational.
• Restore to Factory Defaults. You may need to restore the factory
defaults if the configuration of your unit is changed, if you lose both
network connectivity and the ability to interface to the unit via the web
interface, or following a failed software upgrade. To restore factory
defaults, press the Reset button for more than 10 seconds. The unit
reverts to its factory defaults and after about 30 seconds becomes
operational again.
• LAN (Local Area Network) Port. Connect to Ethernet network
devices, such as a PC, hub, switch, or router. Depending on the
connection, you may need a cross-over cable or a straight-through
cable.
• Power. Make sure you observe the proper power requirements.
• ADSL Port. WAN interface that connects directly to the phone line.
ECI Telecom Ltd. Proprietary
8
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
5.2
User Guide
LED Descriptions
The following pictures show where the LED indicators are positioned on the
units. An explanation of each LED follows.
Power
LED
Internet
Link
LAN
LEDs
ADSL
Sync
Figure 3. B-FOCuS Router 312+
• Power LED. Indicates that power is supplied to the unit.
• ADSL Link. This LED serves two purposes. If it is continuously lit, the
ADSL interface is successfully connected to a device through the WAN
port. If the LED flickers, the router is training.
• LAN Link. This LED serves two purposes. If it is continuously lit, the
Ethernet interface is successfully connected to a device through the
LAN port. If it flickers, network activity is in progress.
• Internet Link. The Internet LED is off if no connection is established or
the connection is not used. When it is green, an Internet connection has
been established.
ECI Telecom Ltd. Proprietary
9
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
5.3
User Guide
LED Table
The LED table below can help diagnose problems.
Table 2. B-FOCuS Router LEDs
Off
Power not
applied
LED Status
Green
Normal
Operation
ADSL Link
ADSL line not
connected
ADSL line is
trained
ADSL line is
training
LAN Link
Wrong type of
Ethernet cable
used
Ethernet line is
connected
Ethernet traffic
is flowing
Internet Link
No Internet link
established
Internet link
established
N/A
LED
Power
ECI Telecom Ltd. Proprietary
10
Blinking
N/A
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
6
User Guide
Troubleshooting
Below is a list of common problems. Before calling technical support, please
look through these issues to see if they help solve your problem.
6.1
The Router is not Functional
• Check that the power LED is green.
• Check that the network cables are installed correctly.
• Check that the LAN and Internet Link LEDs are green.
• Check that the ADSL Sync LED is green.
• Make sure that your PC and the router are on the same network
segment. The router’s default IP address is 10.0.0.138; make sure that
your PC’s network adapter is within the same 10.0.0.x subnet. If you are
running Windows, you can open a DOS window and type IPCONFIG to
verify this data.
• Ping the router from your PC.
a. From the desktop, click Start > Run.
b. In the Open box, type Ping 10.0.0.138
c. A positive result displays as:
Reply from 10.0.0.138 bytes=32 time<10ms TTL=255.
• Ping the WAN.
• If you can ping the router and your protocols are configured correctly,
you should be able to ping the ISP’s network (your ISP should have
provided the IP address of their server). If you cannot ping the ISP’s
network, make sure you are using the correct protocols with the correct
VPI/VCI values.
• Make sure NAT is enabled for your connection. If NAT is disabled your
router will not route frames correctly.
• Disable proxies on your browser. If you access the router, and instead
of receiving the Login window, the browser displays a login redirection
message, you should verify that JavaScript support is enabled.
ECI Telecom Ltd. Proprietary
11
DWG# 458006-0833-010 A00
B-FOCuS Router 312+
User Guide
• Disable your network card and then enable it.
• Delete your temporary Internet files, history files, and cookies.
• Verify that your Windows LAN is configured for dynamic IP Addresses.
• Verify that none of your applications are trying to create a dial-up
connection to the Internet.
• If your router does not work after performing all the steps above, press
the reset button on the back panel for 10 seconds until the ADSL Sync
lamp turns off. The router will revert into its factory default settings.
Perform the above procedures again.
6.2
The ADSL Link LED Blinks but Does Not Go
Solid
The ADSL line is trying to train but for some reason it cannot establish a valid
connection. You are too far from the telco central office. Contact your DSL
service provider for further assistance.
6.3
The DSL Link LED is Always Off
Make sure you have ADSL service. You should get some kind of information
from your ISP that states that ADSL service is installed. You can usually tell if
the service is installed by listening to the phone line; you will hear some highpitched noise. If you cannot hear high-pitched noise, contact your ISP.
Verify that the phone line is connected directly to the wall socket and to the
ADSL input on your router. If you have installed a splitter on the phone line, and
accidentally connected the router to the phone side, the ADSL light will not
come on.
ECI Telecom Ltd. Proprietary
12
DWG# 458006-0833-010 A00