U-Line COMBO C2275DWR Installation guide

Installation Guide
C2275DWR —
Combo® Drawer
Refrigerator/Freezer/Ice Maker
www.U-LineService.com
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696
OnlineService@U-Line.com
©2007 U-Line Corporation
09/2007
C2275DWR — Ice Maker/Refrigerator
Contents
Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearances Information . . . . . . . . . . . . . . . . . . . . . . . . .
Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . .
No Custom Drawer Panels . . . . . . . . . . . . . . . . . . . . . . .
Custom 1/4" Drawer Panel Inserts . . . . . . . . . . . . . . . .
Full Overlay Drawer Panels . . . . . . . . . . . . . . . . . . . . . .
Checking Drawer Alignment . . . . . . . . . . . . . . . . . . . .
Adjusting Drawer Alignment . . . . . . . . . . . . . . . . . . . .
Water Supply Connection . . . . . . . . . . . . . . . . . . . . . . .
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . .
Leveling Information . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation of the C2275DWR . . . . . . . . . . . . . . . . . . .
Anti-Tip Kit Installation . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Troubleshooting . . . . . . . . . . . . . . . . . . . . .
Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Start-Up Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Follow Safety Precautions
4
4
5
5
6
7
7
8
9
10
12
13
13
13
14
14
15
15
16
17
IMPORTANT
PLEASE READ all instructions completely before
attempting to install or operate the unit.
• This unit requires connection to the water supply.
Improper hook-up can result in substantial property
damage! If you are unsure of your ability to safely
connect the water supply to the unit, consult a licensed
plumber for assistance.
• This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a
qualified electrician in accordance with applicable
electrical codes.
Safety Alert Definitions
Safety items throughout this guide are labeled with a
Danger, Warning or Caution based on the risk type:
DANGER
Danger means that failure to follow this safety
statement will result in severe personal injury or
death.
WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury,
or death.
CAUTION
Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.
www.U-LineService.com
2
09/2007
C2275DWR — Ice Maker/Refrigerator
General Precautions
2 Inspect and Plan
Use this appliance for its intended purpose only and follow
these general precautions along with those listed throughout
this guide:
You have received a carton containing your C2275DWR
Combo Drawer Model Ice Maker/Refrigerator with a
package inside containing a Use and Care Guide, a Product
Registration Card, water connection parts and Anti-Tip Kit.
Complete and mail the Product Registration Card or
register online at www.U-LineService.com. Once your unit is
installed, keep the Use and Care Guide and this Installation
Guide in a safe place for future reference.
WARNING
SHOCK HAZARD — Electrical Grounding Required.
• Keep the unit unplugged throughout installation
except during testing.
• Never remove the round grounding prong from the
plug and never use a two-prong grounding adapter.
• Never use an extension cord to connect power to
the unit.
• Always keep your working area dry.
Your unit is Overlay or Stainless Steel. Overlay units have
drawers with top handles designed for the installation of full
overlay drawer panels. When full overlay panels will not be
used, replacement handles MUST be installed (part number
26070-01). Stainless Steel units have drawers with seamless
full wrap stainless steel fronts (that do not accept custom
panels), sculpted stainless steel handles and black vinyl-clad
cabinets. Please carefully follow the directions that apply to
your unit and your intended design.
WARNING
The Anti-Tip Kit must be installed on this unit before
it is used. Never use the drawers as steps or as a
shelf to support more than the drawers’ contents.
Serious personal injury could occur.
Tools/Materials Required
• Wrenches
CAUTION
• Screwdrivers — slotted and Phillips head
• 1/4-inch OD copper tubing and shut-off valve for water
supply line
• Use care when moving and handling the unit. Use gloves
to prevent personal injury from sharp edges.
• Do not lift the unit by the drawer handle.
• 1/4-inch thick drawer panel material and cutting tools
(Overlay units) (IF using a 1/4” Panel)
• Do not install the unit behind closed doors or in any way
that would obstruct airflow to the front grille, which may
cause the unit to malfunction.
• 3/4-inch thick drawer panel overlay material, cutting tools,
drill and bits (Overlay units) (If using 3/4” Overlay)
Inspection
Unwrap and inspect the unit on a flat, level surface capable
of supporting its entire weight.
Removing Protective Coating
All Models:
The protective coating covering the inside of the top drawer
must be removed before using.
Stainless Steel Models:
When inspecting/installing a Stainless Steel unit, the
protective coating covering the drawer fronts must be
removed. Start at a corner of the drawers and pull back the
protective coating to remove it from the drawer fronts.
After all the protective coating has been removed from the
drawers, clean all Stainless Steel surfaces with Claire Stainless
Steel Polish and Cleaner or comparable product or a mild
detergent and warm water solution and soft cloth. Do NOT
use abrasive cleaning agents.
Note: If cleaning with mild detergent and warm water
solution and soft cloth, the unit MUST be treated with Claire
Stainless Steel Polish and Cleaner or comparable product to
prevent discoloration.
09/2007
3
www.U-LineService.com
C2275DWR — Ice Maker/Refrigerator
Exterior Cleaning
3 Prepare Site
(As Required)
Your U-Line product has been designed for built-in
installation. Your unit does not require additional air
space for top, sides or rear. However, the front grille must
NOT be obstructed and clearance is required for water
and electrical connections in the rear.
Overlay Models:
• The drawers, grille and cabinet may be cleaned with a
mild detergent and warm water solution. Do not use
solvent-based or abrasive cleaners. Use a soft sponge
and rinse with clean water. Wipe with a soft, clean
towel to prevent water spotting.
Note: Unit can NOT be installed behind a closed cabinet
door.
Stainless Steel Models:
Cut-Out Dimensions
• Stainless steel models can discolor when exposed to
chlorine gas, pool chemicals, salt water or cleaners with
bleach.
• Keep your stainless steel unit looking new by cleaning
with a good quality all-in-one stainless steel cleaner/
polish on a monthly basis. For best results use Claire
Stainless Steel Polish and Cleaner, which can be
purchased from U-Line Corporation. (The part number
is 173348.) Comparable products are acceptable.
Frequent cleaning will remove surface contamination
that could lead to rust. Some installations may require
cleaning on a weekly basis.
See Electrical
Specifications
for Power Supply
24"
34-1/4"
to
35-1/8"
8"
• Do not clean with steel wool pads.
• Do not use cleaners that are not specifically
intended for stainless steel (this includes glass,
tile and counter cleaners).
24-3/16"
Figure 1
• If any surface discolors or rusting appears, clean it
quickly with Bon-Ami or Barkeepers Friend Cleanser
and a non-abrasive cloth. Always clean in the direction
of the grain. Always finish this process with Claire
Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
Follow the cut-out drawing in Figure 1. The 24-3/16"
width allows 1/4" for ease in installation and removal of
the unit. 24" is the cabinet depth in most installations.
The unit is 23-11/16" deep including the drawer and not
the full handle or 3/4" overlay (see Figure 2).
• Use of abrasive pads such as Scotchbrite will
cause the graining in the stainless to become
blurred.
• Rust that is allowed to linger can penetrate into the
surface of the stainless steel and complete removal of
the rust may not be possible.
www.U-LineService.com
4
09/2007
C2275DWR — Ice Maker/Refrigerator
Product Dimensions
Clearances Information
The unit must be installed in a wall or under a countertop to allow for the installation of the Anti-Tip Kit (see
Page 14).
25-13/16"
Including
Handle
23-11/16"
WARNING
34-1/8"
The Anti-Tip Kit must be installed on this unit
before it is used. Never use the drawers as steps
or as a shelf to support more than the drawers’
contents. Serious personal injury could occur.
34-1/8"
The unit is designed so it can be installed next to a wall on
either side (see Figure 3).
23-15/16"
23-15/16"
Black
Stainless Steel
24-7/16"
Including
Overlay
34-1/8"
23-15/16"
Wood Overlay
Figure 2
Please note that the unit has adjustable feet that can add
one additional inch to height during leveling or to match
adjacent cabinets (see Figure 28 on Page 13).
09/2007
Cabinet
or Wall
Figure 3
5
www.U-LineService.com
C2275DWR — Ice Maker/Refrigerator
Other Site Requirements
The drawer unit can be installed with an appliance or
fixture located in front of it, as long as there is adequate
clearance for the drawer to be opened and removed
when servicing (see Figure 4).
Power Supply
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A circuit (normal household current). See
Electrical Specifications on Page 13.
Note: U-Line recommends you consider additional
clearance in front of the open drawer for convenience.
Water Supply
The unit requires a 1/4-inch OD water supply line and a
shut-off valve. For more information see Page 12.
Environmental Requirements
Many U-Line models are designed to operate in harsh
outdoor/marine environments. Special considerations
include the following:
• The units are designed to operate between 50°F (10°C)
and 110°F (40°C). High ambient temperatures (110°F
[40°C] or higher) may reduce the unit’s ability to reach
low temperatures.
• For best performance, keep the unit out of direct
sunlight and away from heat generating equipment.
24" Min.
• In climates where high humidity and dew points are
present, condensation may appear on outside surfaces.
This is considered normal. The condensation will
disappear when the humidity drops.
• U-Line does not recommend installation of glass front
models (Wine Captain® wine storage models and
Beverage Centers) as well as the Combo Drawer model
(Refrigerator/Freezer/Ice Maker) outdoors, or in
tropical climates where high humidity and dew point
are present on a regular basis, unless air-conditioning
(typical 72°F, 75%RH) will be used.
Figure 4
www.U-LineService.com
6
09/2007
C2275DWR — Ice Maker/Refrigerator
Drawer Panel Installation
4 Prepare and Install Drawer Panel
Install the insert as follows:
(Overlay Units Only)
CAUTION
Two types of custom drawer panels can be installed on
your Overlay unit to harmonize with or accent the
surrounding décor: Custom 1/4" Inserts or Full Overlays.
Overlay units may also be installed with no custom drawer
panel.
Use care when handling the insert. Insert edges may be
sharp.
1. Open drawer. Pull drawer
gasket out of groove (top
edge of drawer only).
Start in the middle and
pull outward, moving
toward the edge (see
Figure 5). This may take
some force.
No Custom Drawer Panels
When full overlay drawer panels are not used,
replacement handles (part number 26070-01) MUST be
installed on each drawer. To replace the handle when no
custom panel will be installed, follow the instructions
under Custom 1/4" Drawer Panel Inserts, Door Panel
Installation below, disregarding Steps 4 and 5.
Gasket
3. Remove the original
handle and discard.
Drawer Panel Preparation
Custom drawer panels can be inserted into the drawer
fronts. Custom drawer panels can be flat or raised, as long
as the maximum panel thickness where inserted into the
drawer front reveal (channel) is 1/4"-thick. For raised
panels, the depth of the reveal is 1/4" on all four sides.
4. Remove and discard
existing panel and
cardboard spacer.
Figure 5
5. Slide custom drawer
panel insert into 1/4-inch
channel in drawer front.
IMPORTANT
6. Holding drawer gasket out
of the way, replace handle
on drawer, making sure it
is seated properly on insert
and that screw holes line
up.
Raised panels will reduce the drawer’s front clearance if
the unit is installed facing an appliance or structure (see
Page 5).
Cut the panel inserts to the following dimensions.
Custom 1/4" Dimensions:
Standard
Handle
Full Handle
7. Install two small screws
removed in Step 2.
23-1/32"
12-15/32"
8. Starting at the corners and
working inward, push
drawer gasket into place
on drawer. Go on to
5 Adjust Drawers.
The door panels must not have a total weight of more
than 20 lbs.
09/2007
Screw
2. Remove and save the two
outside screws (see Figure
6).
Custom 1/4" Drawer Panel Inserts
Width:
Height:
Handle
7
Figure 6
www.U-LineService.com
C2275DWR — Ice Maker/Refrigerator
Full Overlay Drawer Panels
Attaching the Full Overlay Panel
Drawer Panel Preparation
1. If user-supplied cabinet handles will be used, attach
their hardware to the overlay panel at this time.
Full overlay drawer panels completely cover the drawer
fronts and handles to give a built-in appearance. Overlay
units are shipped ready for full overlay installation.
IMPORTANT
User-supplied cabinet handles MUST be counter bored to
make sure mounting hardware is below surface of overlay
panel. Failure to do so can cause damage to overlay panel
and/or drawer. Overlay panel will not sit flush to drawer if
mounting hardware is not counter bored.
Note: For standard installations, both drawers mount the
same and a 1/2" gap is achieved between drawers.
1. Cut the overlay to the following dimensions.
Full Overlay Dimensions:
Width:
Height:
23-3/4"
Tape
Back of
Wood
Panel
14-3/4"
Drawer Panel
IMPORTANT
The thickness of the wood overlay panel must be 3/4".
The door panel must not weigh more than 20 lbs.
Drawer Panel Installation
Removing Existing Drawer Fronts
Side of
Wood Panel
1. Open drawer. Pull drawer gasket out of groove (top
edge of drawer only). Start in the middle and pull
outward, moving toward the edge (see Figure 7). This
may take some force.
11/32"
Bottom
3/8"
Both Sides
Figure 9
2. Remove and save the two screws located at the ends of
the handle (see Figure 8). Remove the handle.
Handle
Bottom of
Wood Panel
2. Place and tape the existing drawer panel on the back of
the overlay panel (see Figure 9).
3. Drill the five holes (5/32" drill 3/8" deep) through both
panels according to Figure 10.
Screw
Gasket
Top of
Wood Panel
Vinyl Coated
Steel Panel
2-15/16"
14-3/4"
5/32" x 3/8" Deep –
5 Places
11-13/16"
Figure 7
Figure 8
1"
1"
www.U-LineService.com
1"
11-7/8"
3. Remove existing panel and cardboard spacer. Discard
the spacer.
23-3/4"
Figure 10
8
09/2007
C2275DWR — Ice Maker/Refrigerator
CAUTION
5 Adjust Drawers
It is important to ensure that all drilled holes are drilled to
the correct depth in order to avoid splits in the wood
when hardware is installed.
Checking Drawer Alignment
The unit’s drawers are aligned at the factory before
shipment. However, their alignment could have been
disturbed during shipment or during overlay panel
installation.
4. Remove tape adjoining the panels and enlarge the five
holes in the overlay panel using a 0.201" (#7) drill.
5. Attach the drawer panel to the overlay panel using
#10 x 5/8" wood screws and nylon spacers. The nylon
spacers fit between the overlay panel and the door
panel as shown in Figure 11. The spacers allow the
original drawer panel to slide back into the 1/4"-thick
drawer front reveal (channel).
Typical
Wood Panel
Aligned
Front-to-Back
Aligned
Side-to-Side
Drawer Panel
#10 x 5/8"
Round Head Screw
Five Required
Aligned
Top-to-Bottom
Plastic
Spacer
Five
Required
Figure 12
See Figure 12. Check each drawer to confirm that it is
aligned:
Figure 11
• Side-to-Side — When viewed from the top, the
drawer front should be square with the sides of the
cabinet.
IMPORTANT
• Front-to-Back — When viewed from the side, the
drawer front should be straight with the cabinet’s
sides, not cocked forward or back.
Drawer panel and overlay panel must be aligned properly
or the drawer will not operate correctly.
Assembling the Drawer Front
• Top-to-Bottom — When viewed from the front, the
drawer should be level horizontally.
1. Install the assembled panel by sliding the original door
panel back into the drawer front.
If both drawers are properly aligned, go on to 6 Prepare
Plumbing. If either drawer is not aligned, carefully
follow instructions to remove that drawer, make the
necessary adjustment and re-install the drawer.
2. Replace the handle assembly and secure with the two
screws removed in Step 2 under Removing Existing
Drawer Fronts.
3. Starting at the corners and working toward the center,
push the drawer gasket back into place. Go on to
5 Adjust Drawers.
09/2007
9
www.U-LineService.com
C2275DWR — Ice Maker/Refrigerator
Adjusting Drawer Alignment
Minor Adjustment:
Note: The mounting holes
on the slide are slightly
larger than the screws’
diameter.
WARNING
SHOCK HAZARD — The unit must be unplugged
from the wall outlet during drawer removal,
adjustment and re-installation.
1. Loosen the slide’s
mounting screws.
Drawer Removal
2. Push the slide
backward.
1. Confirm that the unit is
unplugged from wall
outlet.
Mounting
Screw
Push Slide
Backward
3. Retighten the screws.
See Figure 15.
Figure 15
2. Unplug the drawer’s
connection wiring (top
drawer only).
Severe Adjustment:
3. Remove the mounting
screws. See Figure 13.
4. Pull the drawer
completely out of the
unit.
Loosen
Mounting Screws
Note: The slides have
extra mounting holes that
may be used.
Figure 13
Mark and Drill New
Mounting Holes
1. Remove the slide’s
mounting screws.
2. Reposition the slide so
it is the same distance
from the front of the
liner as the other slide.
Measure to confirm.
CAUTION
Use care when handling the drawer. Drawer edges,
drawer rail and the unit’s slide may be sharp.
Figure 16
3. Mark new drilling holes
using different sets of mounting holes on the slide. See
Figure 16.
IMPORTANT
Drawer adjustments are made by moving the slide that
carries the drawer’s rail. Minor adjustments may be made
by loosening one of the slide’s mounting screws, adjusting
the slide and retightening the screw. Severe adjustments
may be made by removing the slides’ mounting screws,
drilling new mounting holes and remounting the slide.
Note: Front location holes are shown. Corresponding rear
holes will also need to be marked.
4. Drill all the new holes with a #30 drill bit.
5. Remount the slide.
Side-to-Side Adjustment
See Figure 14. The drawer
will need a Side-to-Side
Adjustment if, when
viewed from the top, the
drawer front is not square
with the sides of the
cabinet. This is caused by
one of the slides being
mounted too far forward
on the unit’s liner.
Push Slide
Backward
Front-to-Back Adjustment
See Figure 17. The drawer
will need a Front-to-Back
Adjustment if, when
viewed from the side, the
drawer front is cocked
forward or back. This is
caused by the front slide
mountings not being level
with the rear slide
mountings.
Not Aligned Side-to-Side
Top View of Unit
Not Aligned Front-to-Back
Figure 14
Side View of Unit
Figure 17
www.U-LineService.com
10
09/2007
C2275DWR — Ice Maker/Refrigerator
Minor Adjustment:
Minor Adjustment:
Note: The mounting holes
on the slide are slightly
larger than the screws’
diameter.
Note: The mounting holes
on the slide are slightly
larger than the screws’
diameter.
Screws Should
Be Loose
1. Loosen one slide’s
mounting screws.
1. Loosen one slide’s
mounting screws.
2. Level the slide.
2. Push the slide upward
or downward to match
the position of the
other slide.
3. Retighten the screws.
See Figure 18.
4. Repeat procedure for
the other slide.
Level the Slide
3. Retighten the screws.
See Figure 21.
Figure 18
Severe Adjustment:
Note: The slides have
extra mounting holes that
may be used.
Push Slide
Upward or
Downward
Figure 21
4. Repeat the procedure with the other slide if necessary.
Severe Adjustment:
Mark and Drill New
Mounting Holes
Note: The slides have
extra mounting holes that
may be used.
1. Loosen one slide’s rear
mounting screws.
Mark and Drill New
Mounting Holes
1. Remove one slide’s
mounting screws.
2. Remove the slide’s
front mounting screws.
3. Reposition the slide so
it is level.
Loosen
Mounting Screws
2. Reposition the slide so
it is the same distance
from the bottom of the
liner as the other slide.
Measure to confirm.
Level the Slide
Figure 19
4. Mark new front drilling
holes using a different
set of mounting holes on the slide. See Figure 19.
Push Slide
Upward or
Downward
Figure 22
3. Mark new drilling holes
using different sets of
mounting holes on the slide. See Figure 22.
5. Drill the new holes with a #30 drill bit.
6. Remount the slide.
Note: Front location holes are shown. Corresponding rear
holes will also need to be marked.
7. Repeat procedure for the other slide.
Top-to-Bottom (and Left-to-Right)
Adjustment
4. Drill all the new holes with a #30 drill bit.
5. Remount the slide.
Re-installation of Drawer
CAUTION
Not Aligned
Top-to-Bottom
Use care when handling the drawer. Drawer edges,
drawer rail and the unit’s slide may be sharp.
Not Aligned Left-to-Right
1. Set the drawer’s rails onto the slides.
2. Re-install the rails’ mounting screws. See Figure 13 on
Page 10.
3. Plug in the drawer’s connection wiring (top drawer
only).
Front View of Unit
Top View of Unit
4. Go on to 6 Prepare Plumbing.
Figure 20
See Figure 20. The drawer will need a Top-to-Bottom
Adjustment if, when viewed from the front, the drawer is
not level horizontally. Viewed from the top, one side will
protrude. This is caused by one of the slides being
mounted higher than the other slide on the unit’s liner.
09/2007
11
www.U-LineService.com
C2275DWR — Ice Maker/Refrigerator
2. Locate the compression fitting and ferrule packed with
the unit. Slide the compression fitting and ferrule over
the 1/4-inch Outside Diameter water supply line. Do
not use thread sealing compound or tape. Using two
wrenches, tighten the compression fitting on the
supply line (see Figure 24).
6 Prepare Plumbing
Plumbing installation must observe all state and local
codes. All water connections MUST BE made by a licensed/
qualified plumbing contractor. Failure to follow
recommendations and instructions may result in damage
and/or harm.
3. Carefully bend the water supply line into position and
connect the line to the solenoid valve (see Figure 25).
Avoid kinking the water supply line.
WARNING
To prevent accidental electrocution, make certain
that the floor surfaces surrounding the unit are
dry whenever power is removed from, or applied
to, the unit.
Water Supply Connection
When connecting the water supply, follow these
guidelines:
• Review the local plumbing codes before you install the
unit.
• Connect to the cold water supply.
• The water pressure should be between 20 and 120 psi.
• Install a shut-off valve in the 1/4 inch Outside Diameter
water supply line.
• Connect sufficient tubing to the unit so that tubing
may be looped, allowing the unit to be removed for
cleaning and servicing (see Figure 25). However, make
certain that the tubing is not pinched or damaged
during installation.
Normal operation creates some vibration. A water supply
line contacting cabinet wall may cause excessive noise
during operation or damage to the line.
Note: U-Line recommends the use of copper tubing
for installation. The use of other types of tubing is not
recommended due to potential aftertaste & deterioration
over time.
4. Allow extra water supply line length to provide slack for
easy removal from the recessed area (see Figure 25).
This will also safeguard against kinking the line.
To connect to water supply:
5. Go on to 7 Prepare Power Supply.
Figure 25
IMPORTANT
1. Install the 1/4 inch Outside Diameter copper water line
from the main water source (see Figure 23).
Water
Connection
Figure 23
www.U-LineService.com
Figure 24
12
09/2007
C2275DWR — Ice Maker/Refrigerator
7 Prepare Power Supply
8 Level the Unit
Electrical Specifications
Leveling Information
CAUTION
IMPORTANT
It is extremely important that the unit is level. If it is not
level, the ice mold will not fill evenly.
Electrical installation must observe all state and local
codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a
qualified electrician.
1. Use a level to
check the
levelness of the
unit from front to
back and from
side to side. Level
should be placed
along top edge
and side edge as
shown (see
Figure 27).
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A power supply (normal household current).
An individual, properly grounded branch circuit or circuit
breaker is recommended. GFCI (ground fault circuit
interrupter) is usually not required for fixed location
appliances and is not recommended for your unit because
a GFCI could be prone to nuisance tripping. However, be
sure to consult your local codes.
See Figure 26 for recommended receptacle location.
Figure 27
ULIN_0045_A
2. If the unit is not level, adjust the feet on the corners of
the unit as necessary (see Figure 28).
23-11/16"
7"
1-1/2"
Figure 26
ULIN_0046_A
Figure 28
WARNING
3. Check the levelness after each adjustment and repeat
the previous steps until the unit is level. Go on to
9 Install the Unit.
SHOCK HAZARD — Electrical Grounding Required.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
Installation Tip
• Never use an extension cord to connect power to
the unit.
If the room floor is higher than the floor in the cut-out
opening, adjust the rear feet to achieve a total unit rear
height of 1/8" less than the opening’s rear height. Shorten
the unit height in the front by adjusting the front feet.
This allows the unit to be gently tipped into the opening.
Readjust the front feet to level the unit after it is correctly
positioned in the opening.
Go on to 8 Level the Unit.
09/2007
13
www.U-LineService.com
C2275DWR — Ice Maker/Refrigerator
9 Install the Unit
Horizontal Mounting
(Left Side Shown)
Countertop or Wall Header
Installation of the C2275DWR
1. Plug in the power cord.
B
2. Open the top drawer.Press and hold the POWER icon to
turn the unit OFF. (see Figure 31,1)
Note: If the unit is NOT turned OFF, water will
immediately start flowing into unit when it is first
plugged into the electrical outlet and water supply is on.
A
3. Open the water supply valve in the main water source.
4. Gently push the unit into position. Be careful not to
kink the water supply line or entangle the electrical
cord.
C
5. Re-check the leveling, from front to back and side to
side. Make any necessary adjustments. The unit’s top
surface should be approximately 1/8" below the
countertop.
Vertical Mounting
(Left Side Shown)
Cabinet or Wall Stud
Anti-Tip Kit Installation
WARNING
B
• The Anti-Tip Kit must be installed on this unit
before it is used.
• Additional blocking or special fasteners may be
required for installation. Installer is responsible
for secure attachment to prevent the unit from
tipping.
C
• Make sure the mounting screws attaching the
unit to the counter, cabinet or wall are deep
enough into the mounting surface to support the
weight of the drawers and the items that will be
inside the drawers.
• Never use the drawers as steps or as a shelf to
support more than the drawers’ content. Serious
personal injury could occur.
A
Figure 29
2. Insert the screws through the anti-tip bracket (B) and
attach the bracket to the unit. Tighten screws securely.
After leveling, the unit must be secured to a counter, a
cabinet or a wall to prevent tipping.
3. Repeat for the other side.
1. Open the upper drawer to expose the six screws (A)
installed at the top two corners (three at each corner).
Remove the appropriate screws for horizontal or
vertical mounting (see Figure 29). Do not discard.
www.U-LineService.com
Note: The bracket should be flush with the surface it is
being attached to. If it is not, loosen the screws and slide
the bracket against the mounting surface. Tighten screws
securely.
14
09/2007
C2275DWR — Ice Maker/Refrigerator
4. Using two of the screws (C) supplied, fasten the screws
through the bracket and into the counter, cabinet or wall.
10 Start-Up for the First Time
IMPORTANT
Initial Start-Up
Certain cabinets or countertops may require special
fasteners or additional wood blocking to anchor properly.
All U-Line units are shipped from the factory with the
controls that are preset. No initial adjustments are
required.
CAUTION
Once installation and leveling is complete, the unit is
ready for initial start-up and operation. Open the top
drawer, press and hold the POWER icon (see Figure 31,1)
on the display panel for aproximately ten seconds until
the °F symbol flashes and release.
Make sure the screws are back far enough so they do not
damage any exposed front surface of the cabinet.
Installation Troubleshooting
Q:
IMPORTANT
Problem
U-Line recommends that the unit be allowed to run
overnight and make ice prior to loading the
refrigerator and/or freezer with product.
Water is leaking under the unit.
A:
Solution
1. As soon as the icemaker
mold reaches the proper
temperature, the ice
maker mechanism will fill
the mold with water.
A water leak under the unit is most likely caused by a bad
connection in the water supply line. Make sure the water
line’s brass fitting is screwed tight to its valve and
threaded correctly.
Q:
Note: There is an interior
light in each drawer which
illuminates when the drawer
is opened.
Problem
The drawer remains open unless it is pushed closed.
A:
Solution
Note: The first cubes may be Figure 30
small because of air in the
water line. After two hours, cubes will be standard size.
The drawer should be self-closing when it is open
approximately 8". If it is not, re-check leveling from front
to back of the unit and readjust if necessary.
2. The ice maker will continue to produce until the bin is
full. You may interrupt production by raising the bin arm
into an upright and locked position (see Figure 30).
While the bin arm is locked, the unit will maintain
temperature for ice storage.
IMPORTANT
It is possible that dirt or scale will dislodge in the water
line. Always throw away all ice cubes made during the
first twenty-four (24) hours of operation.
09/2007
15
www.U-LineService.com
C2275DWR — Ice Maker/Refrigerator
Start-Up Troubleshooting
Electronic Control Panel
The electronic control with digital display (Figure 31) is
located in the top drawer. It is configured to show a single
temperature continuously. This set-point temperature is a
base number used by the controller to maintain the
temperature zone in your unit. The factory set-point is
38°F for the top drawer which will show when the unit is
first powered up. The factory set point for the ice
compartment is 0°F.
1
2
3
4
Q:
Problem
Unit does not appear to turn on when POWER icon is
pressed.
A:
Solution
Make sure unit is plugged in and outlet has power (circuit
breaker has not tripped).
5
Q:
Problem
Water does not appear to be flowing into unit.
A:
ULIN_0058_A
Figure 31
Solution
Check that the water is connected and turned on and the
line is not obstructed. Remember that the ice maker
mechanism will not fill the mold with water until the
mold reaches the proper temperature.
Other Settings
Other settings for the unit are factory preset. No adjustments
should be necessary at this time. See the Use and Care Guide
for information on:
Q:
Problem
The cubes produced during the first two to three hours of
operation have been discarded. New cubes still appear
cloudy.
• Removing the upper drawer’s storage bin
• Removing the lower drawer’s ice bucket
• Adjusting the upper drawer’s organizer, left-to-right or
front-to-back
A:
Solution
This is normal and is caused by air being trapped in the
cube during fast freezing.
IMPORTANT
See the Use and Care Guide’s Troubleshooting Guide for
more solutions.
www.U-LineService.com
16
09/2007
Who to Call
Service Information
If the need for service arises, call the U-Line Customer
Care Center directly @ 800-779-2547. To ensure accurate
assistance, please have your Model Number and Serial
Number and an explanation of the problem.The Model
and Serial Number plate is located inside unit at upper
right hand corner.
If you need to locate a service company, you can go online
at www.U-LineService.com and search for a service
company by zip code.
For more than four decades, U-Line has distinguished itself as the leader in built-in
undercounter ice making, refrigeration and wine storage appliances.
U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in
undercounter icemakers, Combo® icemaker/refrigerators, Wine Captain® wine storage units,
refrigerators, refrigerated drawers and refrigerator/freezers.
©2007 U-Line Corporation
Publication No. 30206E
09/2007 Rev. A