Digimerge DH200 Operating instructions

Thank you for purchasing this product. Digimerge is committed to providing our
customers with a high quality, reliable security solution.
This manual refers to the following models:
• DH200+ Series
For more information on this product, firmware updates, and accessory products, please
visit us at:
www.digimerge.com
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVER. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the products ' enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF THE PLUG TO THE WIDE SLOT AND FULLY INSERT.
Important Safeguards
In addition to the careful attention devoted to quality standards in the manufacturing process of
your video product, safety is a major factor in the design of every instrument. However, safety is
your responsibility too. This sheet lists important information that will help to assure your
enjoyment and proper use of the video product and accessory equipment. Please read them
carefully before operating and using your video product.
Installation
1.
2.
3.
4.
5.
6.
7.
Read and Follow Instructions - All the safety and
operating instructions should be read before the
video product is operated. Follow all operating
instructions.
Retain Instructions - The safety and operating
instructions should be retained for future reference.
Heed Warnings - Comply with all warnings on the
video product and in the operating instructions.
Polarization - Do not defeat the
safety purpose of the polarized or
grounding-type plug.
A polarized plug has two blades
with one wider than the other.
A grounding type plug has two
blades and a third grounding prong.
The wide blade or the third prong
are provided for your safety.
If the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
Power Sources - This video product should be
operated only from the type of power source
indicated on the marking label. If you are not sure of
the type of power supply to your location, consult
your video dealer or local power company. For video
products intended to operate from battery power, or
other sources, refer to the operating instructions.
Overloading - Do not overload wall outlets of
extension cords as this can result in the risk of fire
or electric shock. Overloaded AC outlets, extension
cords, frayed power cords, damaged or cracked wire
insulation, and broken plugs are dangerous. They
may result in a shock or fire hazard. Periodically
examine the cord, and if its appearance indicates
damage or deteriorated insulation, have it replaced
by your service technician.
Power Cord Protection - Power supply cords should
be routed so that they are not likely to be walked on
or pinched by items placed upon or against them,
paying particular attention to cords at plugs,
convenience receptacles, and the point where they
exit from the video product.
8.
Ventilation - Slots and openings in the case are
provided for ventilation to ensure reliable operation
of the video product and to protect it from
overheating. These openings must not be blocked or
covered. The openings should never be blocked by
placing the video equipment on a bed, sofa, rug, or
other similar surface. This video product should
never be placed near or over a radiator or heat
register. This video product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the video
product manufacturer’s instructions have been
followed.
9. Attachments - Do not use attachments unless
recommended by the video product manufacturer as
they may cause a hazard.
10. Camera Extension Cables – Check the rating of
your extension cable(s) to verify compliance with
your local authority regulations prior to installation.
11. Water and Moisture - Do not use this video product
near water. For example, near a bath tub, wash
bowl, kitchen sink or laundry tub, in a wet
basement, near a swimming pool and the like.
Caution: Maintain electrical safety. Powerline
operated equipment or accessories connected to
this unit should bear the UL listing mark of CSA
certification mark on the accessory itself and should
not be modified so as to defeat the safety features.
This will help avoid any potential hazard from
electrical shock or fire. If in doubt, contact qualified
service personnel.
12. Accessories - Do not place this
video equipment on an unstable
cart, stand, tripod, or table. The
video equipment may fall, causing
serious damage to the video
product. Use this video product
only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer or sold with the video product. Any
mounting of the product should follow the
manufacturer’s instructions and use a mounting
accessory recommended by the manufacturer.
iii
Service
Use
13. Servicing - Do not attempt to service this video
equipment yourself as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
14. Conditions Requiring Service - Unplug this video
product from the wall outlet and refer servicing to
qualified service personnel under the following
conditions:
• When the power supply cord or plug is damaged.
19. Cleaning - Unplug the video product from the wall
outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.
20. Product and Cart Combination - Video and cart
combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may
cause the video product and car combination to
overturn.
21. Object and Liquid Entry - Never push objects for
any kind into this video product through openings as
they may touch dangerous voltage points or
“short-out” parts that could result in a fire or
electric shock. Never spill liquid of any kind on the
video product.
22. Lightning - For added protection for this video
product during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage
to the video product due to lightning and power line
surges.
• If liquid has been spilled or objects have fallen into
the video product.
• If the video product has been exposed to rain or
water.
• If the video product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions. Improper adjustment of other controls
may result in damage and will often require
extensive work by a qualified technician to restore
the video product to its normal operation.
• If the video product has been dropped or the cabinet
has been damaged.
• When the video product exhibits a distinct change
in performance. This indicates a need for service.
15. Replacement Parts - When replacement parts are
required, have the service technician verify that the
replacements used have the same safety
characteristics as the original parts. Use of
replacements specified by the video product
manufacturer can prevent fire, electric shock or
other hazards.
16. Safety Check - Upon completion of any service or
repairs to this video product, ask the service
technician to perform safety checks recommended
by the manufacturer to determine that the video
product is in safe operating condition.
17. Wall or Ceiling Mounting - The cameras provided
with this system should be mounted to a wall or
ceiling only as instructed in this guide, using the
provided mounting brackets.
18. Heat - The product should be situated away from
heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that
produce heat.
General Precautions
iv
General Precautions
1. All warnings and instructions in this manual should be followed.
2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use a
water dampened cloth for cleaning.
3. Do not use this unit in humid or wet places.
4. Keep enough space around the unit for ventilation. Slots and openings in the storage cabinet
should not be blocked.
5. During lightning storms, or when the unit is not used for a long time, disconnect the power
supply, antenna, and cables to protect the unit from electrical surge.
FCC CLASS A NOTICE
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s
instruction manual, may cause harmful interference with radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference, in which case you will be required to correct the
interference at your own expense.
This equipment has been certified and found to comply with the limits regulated by FCC, EMC, and
LVD. Therefore, it is designated to provide reasonable protection against interference and will not
cause interference with other appliance usage.
However, it is imperative that the user follows the guidelines in this manual to avoid improper
usage which may result in damage to the unit, electrical shock and fire hazard injury.
In order to improve the feature functions and quality of this product, the specifications are subject
to change without notice from time to time.
www.digimerge.com
v
Features
• H.264 compression, supports D1 resolution video recording
• Security Certified Hard Disk with up to 2TB of data storage
• Backup through USB port to flash and optical drives*
• Excellent quality live and recorded video and audio
• 480fps ‘real-time’ viewing, 240fps recording (8/16 channel)
• CMS-DH application supports up to 300 DVRs, 64 channels, live-playback, E-map, full
• control, up to 8 screen display
• 3G Smart phone viewing and control with Windows Mobile™*
• Fully compatible with both PC and Mac
• Lite
Touch pad control
*Please visit www.digimerge.com/Touch for information, firmware, and compatibility updates for
mobile viewing
vi
TABLE OF CONTENTS
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mouse Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
3
5
6
7
Mouse Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Touch Panel Tips and Tricks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Enabling/Disabling Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using the Virtual Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the Virtual Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Multi-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Repositioning Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Sequential Setup (Auto Sequence) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Continuous Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Event Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Video Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting Motion-only Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Enabling Motion-only recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting Continuous & Motion Recording (C+M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Schedule Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Recording Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Using the Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
vii
Sequential Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Auto Sequence with Front Panel and Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
CAMERA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CONFIGURING MOTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
RECORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Stopping Scheduled Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Overnight Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
EVENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
NETWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
EMAIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
MISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ACCOUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
DISK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Formatting Disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Disk Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Auto Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
INFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
USB Flash Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
External USB HDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
USB CD/DVD-RW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Time Search and Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Viewing Backup Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Using MCD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
CMS-DH Central Management Software . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Installing CMS-DH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Starting CMS-DH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Adding a Virtual DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Creating New Group Folders & Sub folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Configuring General System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Adding Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Recording Video to the hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Playing back recorded video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Remote Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
viii
Video Playback Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Local Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Saving Video Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Converting video files to AVI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Schedule Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Schedule Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Taking Screen Captures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Viewing File Download Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Changing viewing modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
E-Map Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Viewing video on E-Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Configuring E-Map camera settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Zooming into the E-Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Removing camera icon in the E-Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Adding Multiple E-Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Viewing DVR Health . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Closing windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Locking Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
DVR Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Setting PTZ Pre-Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Upgrading the firmware remotely (DH200+ Series only) . . . . . . . . . . . . . . . . . . . . . . . 74
Configuring Post Event Action Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Setting up Post Event Actions on a NO/NC Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Configuring Alarm Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Setting message pop-up notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Setting Video pop-up notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Configuring other Post Action Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
POS Data Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Running CMS-DH on multiple monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
iSMS Client (Remote Viewing on the Mac) . . . . . . . . . . . . . . . . . . . . . . . . . . 82
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Using the iSMS Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
iSMS Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Configuring OSD Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Searching for video remotely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Searching for video locally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Configuring PTZ settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Configuring PTZ Protocols in the iSMS Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Configuring the iSMS Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Digi Imobile Touch - iPhone App. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Digi iMobile Touch Lite - ANDROID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
ix
Installing the BDVRViewer App on your Blackberry . . . . . . . . . . . . . . . .
Appendix A: System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix B: Setting up Remote Viewing . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix C: Digimerge Auto Port Forwarding Wizard . . . . . . . . . . . . . .
Appendix D: Setting Up DDNS Service . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix E: Setting Up Mobile Access. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix F: Connecting PTZ Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix G: Connecting Additional External Monitors . . . . . . . . . . . . . .
Appendix H: Connecting Motion / Alarm Devices . . . . . . . . . . . . . . . . . . .
Appendix I: Full Connectivity Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix J: Replacing the Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix K: Using Listen-in Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix L: Converting Video Files to AVI . . . . . . . . . . . . . . . . . . . . . . . .
Appendix M: Remote Viewing using Internet Explorer . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
x
108
112
114
117
124
127
131
135
136
138
139
142
143
145
147
GETTING STARTED
The system comes with the following components:
DIGIMERGE TOUCH+ DIGITAL VIDEO RECORDER
POWER SUPPLY
OCTOPUS CABLE
[16-CHANNEL
ETHERNET
CABLEONLY]
MOUSE
REMOTE CONTROL
INSTRUCTION MANUAL,
QUICKSTART GUIDE, &
SOFTWARE CD
HARD DRIVE SIZE, NUMBER OF CHANNELS, AND CAMERA CONFIGURATION MAY VARY
BY MODEL. PLEASE REFER TO YOUR PACKAGE FOR SPECIFIC CONTENT DETAILS.
CHECK YOUR PACKAGE TO CONFIRM THAT YOU HAVE RECEIVED THE COMPLETE SYSTEM,
INCLUDING ALL COMPONENTS SHOWN ABOVE.
1
BASIC SETUP
1. Connect the cameras
a. Connect BNC cameras to the BNC ports on the
rear panel (4/8-channel models).
OR
a. 16-CHANNEL MODELS ONLY: Connect the single
end of the octopus cable to the VIDEO IN1-16 port
(see figure 1.1).
Figure 1.0 Connect BNC cameras to the system
b. Connect BNC cameras to the octopus cable.
2. Connect a monitor
a. Connect a VGA cable (not included) from the VGA
port on the rear panel to the VGA port on your
monitor.
Figure 1.1 Octopus cable port (16-channel only)
OR
a. Connect a BNC terminated cable from one of the
Video OUT ports to a TV or CCTV monitor.
3. Connect the mouse (USB or PS/2)
a. Connect the mouse to the USB mouse port on the
rear panel.
Figure 1.2 Connect to a VGA or CCTV monitor, or a TV
NOTE: If using a PS/2 mouse, a USB adapter will
be required (not included).
4. Connect the Ethernet cable
a. Connect an Ethernet cable to the LAN port on the
rear panel of system; connect the other end of the
Ethernet cable to an empty LAN port on your
router or switch (not included).
Figure 1.3 Connect an Ethernet cable and mouse
5. Connect the power cable
a. Connect the power supply to the DC 12V port on
the rear panel of the system; connect the power
cable to an outlet, power strip, or surge protector.
2
Figure 1.4 Connect the power cable
FRONT PANEL
1
2
3
10
4
11
6
5
12
13
14
7
8
9
15
Figure 1.5 Front panel (8-channel model shown)
1.
Channel buttons: Press to view channels individually in full-screen.
2.
: Press to increase values in menu options.
3.
: Press to switch between full-screen single channel, quad, and split-screen display views.
4.
: Press to confirm menu options.
5.
/
6.
CLR: Press to perform the following:
• Live viewing: Show/hide onscreen display (OSD)
• Playback: Play/pause playback
• Menu: Move cursor up
7.
: Press to perform the following:
• Live viewing: Start/Stop recording (password required for stoppage)
• Playback: Increase reverse playback speed 1X, 2X, 4X, 8X, and 16X
• Menu: Move cursor left
/: Press to perform the following:
• Live viewing: Start/stop scheduled recording (Recording Schedule must already be configured;
password required for stoppage)
• Playback: Increase forward playback 1X, 2X, 4X, 8X, and 16X
• Menu: Move cursor right
8.
LEDs: REC will be solid red during recording; HDD will flash green when the system is accessing the
HDD.
9.
POWER: Press to power the system ON/OFF (password required).
3
Front Panel
Front Panel (cont’d.)
1
2
3
10
4
11
12
6
5
13
14
7
8
9
15
Figure 1.6 Front panel (8-channel model shown)
10.
: Press to decrease values in menu options.
11.
: Press to open/close the Time Search menu.
12.
: Press to open/close the Backup menu.
13. MENU/ESC: Press to open/close the Main Menu; press to close menu windows.
14.
/„: Press to perform the following:
• Live viewing: Open the Log menu
• Playback: Stop playback
• Menu: Move cursor down
15. USB Port: Connect a USB flash drive, HDD, or optical drive for critical data backup; connect a USB
flash drive for firmware upgrades
4
REAR PANEL
1
2
3
8
9
4
5
6
7
10
11
12
Figure 1.7 Rear panel (8-channel model shown)
1.
CAMERA IN: Camera input ports for BNC cameras (4/8-channel);
VIDEO IN 1-16: Port for octopus cable (16-channel models only—see figure 1.8)
2.
VIDEO OUT: Video output (BNC) to connect the system to a secondary monitor or DVR.
3.
AUDIO IN: One 3.5" RCA port (mono) for recording audio from an audio capable camera (not included).
4.
VGA: VGA port to connect the system to a VGA monitor.
5.
LAN: Connect an Ethernet cable to connect the system to a router or switch (not included).
6.
MOUSE: USB port to connect a USB or PS/2 mouse (PS/2 mouse requires USB adapter).
NOTE: On the 4-channel DH200+ models, the rear USB port is used for the mouse only.
Do not connect a USB flash drive / external DVD writer to the rear USB port.
NOTE: On the 4-channel DH200+ models, you must use a PS/2 compatible USB mouse
(included). A regular USB 2.0 mouse will not work on the rear panel USB port.
7.
ALARM IN: Alarm block to connect external alarm or motion devices (not included).
8.
SPOT OUT: Video output to connect the system to an external monitor (not included). Spot Out mode
only displays channels switching in an automatic sequence.
9.
AUDIO OUT: One 3.5" RCA port (mono) for audio output.
10. RS422 / 485 / OUT: Connection block for an RS422/485 PTZ
camera (not included).
NOTE: The RS232 ports are for development purposes only.
A PTZ camera cannot be controlled from these ports.
11. DC 12V: Port for 12V DC 3A power supply (included).
12. Exhaust fan: Do not block. Keep clear to allow for proper
ventilation.
Figure 1.8 Octopus cable VIDEO IN (16-channel only)
5
REMOTE CONTROL
1
POWER: Press to power the system ON/OFF
(password required).
2.
Navigation/Menu:
1
• S: Press to move cursor up
• T: Press to move cursor down
8
9
2
• W: Press to move cursor left
• X: Press to move cursor right
10
• MENU: Press to open the Main Menu
3.
: Press to switch between single channel
full-screen, quad, and split-screen displays.
3
4
: Press to confirm menu options/selections.
4.
5.
11
Playback controls:
• : Press to increase reverse playback speed 1X,
2X, 4X, 8X, and 16X.
5
• WX: Press to begin playback; press to switch
between forward and reverse playback
• : Press to increase forward playback speed 1X,
2X, 4X, 8X, and 16X
•
6
: During playback, press to pause; press
repeatedly for frame-by-frame playback; during
live viewing, press to open the PTZ menu
• „: Press to stop playback
•
: During playback, press to pause; press
7
repeatedly for frame-by-frame playback; during
live viewing, press to Spot Out.
6.
7.
Channel buttons: Press to view channels 1~8
individually in full-screen; press to input passwords;
when entering camera titles, press for
alpha-numeric characters.
: Press to open the Time Search menu.
8.
CANCEL/ESC: Press to close menu windows; press
to show/hide the on-screen display (OSD); press to
clear channel indicators (loss, alarm, etc.).
9.
+: Press to increase values in menu options.
10. - : Press to decrease menu options in menu options.
11.
6
z: Press to start/stop manual recording.
You can use the channel buttons on the remote
control to enter numbers, letters, and other
characters.
MOUSE CONTROL
The mouse is the primary control device for the system. To
connect a USB mouse:
• Connect a USB / PS/2 mouse to the USB port on the rear panel—DO
NOT connect the mouse to the USB port on the front panel. The USB
port on the front panel is strictly intended for data transfer.
1
2
3
1.
Left-Button: While in a split-screen display mode,
double-click an individual channel to view it in full-screen;
double-click again to return to the split-screen display mode.
While navigating menus, click to select a menu option;
double-click to open the next menu.
2.
Right-Button: Right-click anywhere on the screen to open the Virtual Remote; double-click anywhere
on the screen to return to the previous menu.
Scroll-Wheel: Move the scroll wheel up or down to increase/decrease the value of a selected menu
option.
3.
Mouse Tips
When using the mouse, the ENTER and EXIT buttons appear in the top-right
corner of every menu window. When you change system settings and
configurations, click
to confirm your changes.
Touch Panel Tips and Tricks
If using the Touch panel, you will often use the following
buttons when controlling the system:
• CLR: Menus: move cursor up; Playback: pause playback; Live
viewing: show/hide OSD; clear channel icons
•
/„: Menus: move cursor down; Playback: stop playback; Live
viewing: open Log menu
• / : Menus: move cursor left; Playback: increase reverse
playback speed; Live viewing: start/stop recording
•
/: Menus: move cursor right; Playback: increase forward
playback speed; Live viewing: start/stop scheduled recording
• Press the MENU/ESC button to open the main menu AND close
windows/exit
NOTE: This manual refers to the CANCEL/ESC button on the remote control for closing/exiting menu windows. If
using the front panel, press MENU/ESC to close/exit menu windows.
• Press the
button to increase values for selected menu options
• Press the
button to decrease values for selected menu options
• Press the
button to enter/confirm.
7
USING THE SYSTEM
The default system password is 000000
To power the system ON/OFF:
1. Connect the power cable to the port on the rear panel.
2. Press the POWER button on the front panel or remote control.
NOTE: You need to press the Power button for initial startup only. The system will load the live
viewing screen on subsequent resets.
NOTE: You will need to input your system password to power off the system.
Quick Setup
By default, the system has Quick Setup disabled. Quick Setup lets you quickly adjust the time and
record mode on the system. The system menu will appear as the Quick Setup menu with only Time
and Record options available.
To access the Quick Setup
menu, from the Main menu,
select Display>Quick Setup.
Then select "ON" to enable
Quick Setup.
Figure 2.0 Quick Setup menu
Using Quick Setup
Use Quick Setup to set the time and configure basic recording settings.
To set the time:
1. Under the Time tab, select DATE and press the ENTER button. Enter the month, day, and year.
2. Select TIME and enter the time (hh/mm/ss).
NOTE: If using the mouse, you will enter the date and time with the Virtual Keyboard.
3. Press the ENTER button to save your changes.
To configure recording settings:
1. Stop ALL RECORDING on the system. Enter your system password (by default, 000000).
2. Under the RECORD tab, select RECORD MODE and select one of the following: CIF 4CH,
FIELD 4CH, FRAME 4CH, CIF 8CH, FIELD 8CH, FRAME 8CH, or CIF + FRAME.
NOTE: If "CIF + FRAME" recording mode is selected, only channel 1 will record in frame—the
remaining channels will record in CIF.
3. Under the RECORD tab, select RECORDING DAYS. Press the +/ - buttons and select 12
HOURS, 1~6 DAYS, 1~20 WEEKS, or NONE.
8
Using the System
Using Quick Setup (cont’d.)
4. Under PRIORITY, select QUALITY (the quality of the video) or RATE (frames per second). If you
select RATE, the video quality and frames per second will be at the lowest possible setting.
This will reduce overall video quality, but will maximize the available hard drive space. Adjust
this setting to best suit your recording environment and security needs. For details on
configuring recording options, see “RECORD” on page 28.
NOTE: The necessary recording parameters will appear under RECORD SETUP INFO at the
bottom of the Quick Setup window.
5. Press the ENTER button to save your settings.
Enabling/Disabling Quick Setup
You must disable Quick Setup in order to access the full system main menu.
To disable Quick Setup:
1. Under the ADVANCED tab, select RUN ADVANCED.
2. Select ON and press the ENTER button. The window closes. Quick Setup has been disabled.
The full main menu will appear when you press the MENU button.
To enable Quick Setup:
1. Press the MENU button. The Main menu opens.
2. Select DISPLAY and press the ENTER button.
3. Under the DISPLAY SETUP tab, move the cursor to QUICK SETUP, select ON and press the
ENTER button.
4. Press the CANCEL/ESC button to exit.
Press the MENU button again to open the Quick Setup menu.
Password
The default system password is 000000. However, you do not have to enter a password upon initial
startup. You can enable this option in Main Menu>System>General. For details, see “GENERAL”
on page 34. For complete information on changing your password and managing users on the
system, see “ACCOUNT” on page 34.
Figure 3.0 Enable password (optional)
9
Using the System
On-Screen Display
The system shows the following for all display views:
1
2
3
6
4
7
5
8
Figure 4.0 Main system display
1.
Recording: "REC" indicates that continuous recording is enabled on at least one channel.
NOTE: If REC does not appear on the onscreen display the system is NOT RECORDING.
2.
Display: Show live video and playback in single channel full-screen, quad, and split-screen
configurations.
3.
Camera Status: Will display a green Motion icon, purple Loss icon, or red Alarm icon.
4.
Channel number: By default, the individual channel number appears at the bottom of the frame with
either a RED number (recording) or WHITE number (no recording).
NOTE: A white number may mean that a channel has been assigned motion recording. For
details, see “Recording” on page 16.
5. Status: Shows recording, display type, and network status. "R" indicates recording;
indicates schedule recording.
NOTE: Always check for these icons. If "R" does not appear in the status bar, the system is NOT
RECORDING. If
does not appear in the status bar, Schedule Recording is NOT ENABLED.
6. Channel Title: You can customize the channel with a unique name for each channel. See
“CAMERA” on page 27.
7.
Date/Time: Shows the date (mm/dd/yyyy), day of the week, and time (24-hour clock).
8.
HDD/Record days: The percentage of free space remaining on the hard disk; number of recording days
remaining.
10
Using the System
Using the Virtual Remote
Right-click anywhere on the screen to open the Virtual
Remote. The Virtual Remote gives you quick access to
many of the system’s features using only a USB mouse
(included).
1
1. Quick Function Keys:
•
•
: Time Search
:Window
Positioning
• Log
• Spot Out
2.
•
•
System Info
Backup
•
: Display Mode
• Zoom
• PTZ
Navigation/Menu:
2
• S: Move cursor up
• T: Move cursor down
• W: Move cursor left
• X: Move cursor right
• MENU: Press to open/close the Main Menu; press to close menu
windows
•
: ENTER/confirm menu options/selections
3
• ESC: Close menu windows; press to show/hide the onscreen
display (OSD); press to clear channel indicators (loss, alarm,
etc.)
• +: Increase values in menu options.
• - : Decrease menu options in menu options
3.
Playback controls:
• „: Stop playback
4
• : Increase reverse playback speed 1X, 2X, 4X, 8X, and 16X
• X: Start playback; press to switch between forward and reverse
playback
Figure 4.1 Virtual Remote
• : Increase forward playback speed 1X, 2X, 4X, 8X, and 16X
• z: Start manual recording (if scheduled recording is not active)
•
4.
: Starts/stops Schedule Recording
•
: During playback, click to pause; click repeatedly for
frame-by-frame playback; during live viewing, click to open the
PTZ menu
•
: During playback, click to pause; click repeatedly for
frame-by-frame playback; during live viewing, click to SPOT
OUT
Channel buttons: Click to view channels 1~8 individually in full-screen; click to input passwords; when entering
camera titles, click for alpha-numeric characters.
NOTE: The button labeled 0/10 means 0 when entering passwords, and 10 when entering
channel 10 for the 16 channel model DVR.
11
Using the System
Playback
During playback, you can right-click anywhere on the
screen to open a condensed version of the Virtual Remote.
1
1. Navigation/Menu:
• S: Move cursor up
• T: Move cursor down
• W: Move cursor left
• X: Move cursor right
• ZOOM: Click to open/close the Zoom windows. Click
zoom then click + / - to increase 2X, 4X.
•
to activate
2
: Click to confirm menu options/selections
3
• ESC: Click to close menu windows; click to show/hide the onscreen
display (OSD); click to clear channel indicators (loss, alarm, etc.)
• +: Increase values in menu options.
Figure 4.2 Virtual Remote during Playback
• - : Decrease menu options in menu options
2.
Playback controls:
• „: Stop playback
• : Increase reverse playback speed 1X, 2X, 4X, 8X, and 16X
• X: Start playback; press to switch between forward and reverse playback
• : Increase forward playback speed 1X, 2X, 4X, 8X, and 16X
3. Quick Function Keys:
•
: Click to open the Time Search menu
• Log: Click to open the Log menu
•
: During playback, click to pause; click repeatedly for frame-by-frame playback
•
: During playback, click to pause; click repeatedly for frame-by-frame playback
Using the Virtual Keyboard
When configuring certain options, such as Camera Title, the Virtual Keyboard opens to make
mouse input easier.
Figure 4.3 Virtual Keyboard
12
Using the System
Setting the Time
It is highly recommended to set the time on the system prior to doing any recording.
NOTE: All recording must be stopped on the system in order to set the time.
Figure 5.0 Time menu
To set the date and time:
button
1. Stop recording on the system by pressing / on the front panel, or pressing the
on the remote control and enter your 6-digit system password (by default, 000000).
NOTE: If using the mouse, right-click and then click
on the Virtual Remote.
2. Press the MENU button to open the system menu. Select SYSTEM and press the ENTER
button. The System menu opens.
3. Select the TIME tab.
4. Select DATE and enter the date (mm/dd/yyyy).
5. Select TIME and enter the time (hh/mm/ss).
NOTE: If using the mouse, use the Virtual Keyboard to enter the date and time.
6. Press the ENTER button to save your changes.
7. Press / on the front panel, or press the
button on the remote control to resume
Continuous Recording.
NOTE: If using the mouse, right-click and then click
on the Virtual Remote.
13
Using the System
Multi-Screen Display
The system can display channels in full-screen single channel, quad, and multi split-screen
displays.
Full-Screen
Quad
Split-Screen 1
Split-Screen 2
(16-channel
models only)
Repositioning Channels
You can reposition the channels on the display screen. This can be very useful when monitoring a
live location(s).
To reposition the display channels:
1. Using the mouse, remote control, or front panel, place the main display screen in either a
quad display, or in a multi split-screen configuration.
NOTE: Repositioning will not work if the main display screen is in full-screen single channel.
1. Using the mouse, right-click anywhere on the screen to open the Virtual Remote.
2. From the Virtual Remote, click
. The Blue Window cursor appears in the top-left channel
(typically channel 1).
3. Reposition the channels through the following:
• Remote Control: Press the button for the channel you wish to place in the location of the Blue
Window cursor. For example, if the cursor is on channel 1, and you want to have channel 4 in
its location, press the 4 button on the remote control
• Front Panel: Press the button for the channel you wish to place in the location of the Blue
Window cursor
Figure 6.0 Blue Window cursor is in channel 1
Press the 3 button to move channel 3 to the channel 1
position.
Figure 6.1 Channels repositioned
Channel 3 is now in the channel 1 position.
4. Press the STWX to change the location of the Blue Window cursor.
5. Press the ENTER button to save your settings.
14
Using the System
Zoom
Use the system’s built-in 2X digital zoom to get a closer look at images in full-screen (full-screen
mode only).
To use zoom:
1. From live viewing, press the number buttons on the front panel or remote control to select a
channel to view in full-screen.
NOTE: The zoom function will not work if the main display screen is in quad or split-screen
configurations.
2. Press the ENTER button. The OSD disappears. A black frame appears in the center of the
screen.
OPTIONAL:
Once the frame is visible,
you can also perform the
following:
• Press + / - to shrink the
frame
• Press the ENTER button
to zoom in 2X
Figure 7.0 Zoom frame (full-screen only)
3. Once the frame is visible, perform any of the following:
• Press STWX to move the frame anywhere on the screen
• Press the ENTER button to zoom in 1X
• Press + to zoom in 2X; press - to zoom out 1X
• Press STWX to scan the image
4. Press the CANCEL/ESC button to exit zoom and return to live viewing.
Sequential Setup (Auto Sequence)
Sequential Setup (Auto Sequence) allows you to view connected cameras in an automatic
sequence. Sequential Setup can include both full-screen and split screen modes.
For more details on Sequential Setup, see see “Sequential Setup” on page 26.
15
RECORDING
By default, the system is set to immediately record at startup from connected cameras—
continuous recording. It is highly recommended to keep continuous recording on at all times.
The system can perform Continuous Recording, Event Recording, and Schedule Recording.
However, the system can only perform one type of recording at a given time.
Continuous Recording
By default, all camera channels are enabled with continuous recording. During Continuous
Recording, the REC icon appears in the top left corner of the OSD, "R" appears in the status bar
at the bottom of the OSD, and any connected cameras will have their channel numbers in RED (see
figure 0.0).
1
2
3
4
• In this example,
Continuous Recording is
on ALL channels (default)
Figure 8.0 Continuous recording on all channels (4CH model shown)
Event Recording
The system includes three modes of event recording:
•
Motion: The system only records when motion is detected by the affected camera
•
Alarm: The system records when an alarm or sensor is triggered
•
Video Loss: The system records when a camera is disconnected or suffers video loss. The
system employs a pre-record function to capture video seconds before the video loss occurred
You can customize the recording parameters (video quality, frames-per-second) of Event Recording in the
Record menu. See “RECORD” on page 28.
16
Recording
Motion
Motion Detection must be applied to specific cameras. If you assign Motion Detection to a camera,
that camera will only record when a motion event is triggered. The camera enabled with Motion
Detection will have a WHITE number on the OSD (see figure 8.1).
1
2
3
4
• In this example, motion
detection was assigned to
camera 4, so the channel
number is WHITE
• Continuous Recording
remains on channels 1~3
Figure 8.1 Motion assigned to channel 4 (4CH model shown)
NOTE: A white number can also indicate that recording on a camera has been disabled. For
better security it is highly recommended to keep continuous recording for all cameras on at
all times. Use caution when assigning motion detection to specific cameras.
When motion is detected by the camera, the motion icon will appear, and the channel number will
turn RED (see figure 8.2).
1
2
3
4
• In this example, motion was
detected on camera 4—the
motion icon appears and the
channel number turns RED
• Continuous Recording
remains on channels 1~3
Figure 8.2 Motion was detected on camera 4 (4CH model shown)
NOTE: Press the CANCEL/ESC button on the remote control, front panel, or Virtual Remote to
clear the motion icon.
NOTE: If you assign motion detection to ALL cameras, the REC icon will not appear in the top-left
corner, but the "R" will remain in the status bar of the OSD.
17
Recording
Alarm
When an alarm is triggered, the system will continue to record, but can apply unique recording
parameters that you can set in the Alarm menu (Main Menu>Alarm). For details, see “EVENT” on
page 30.
NOTE: Press the CANCEL/ESC button on the remote control, front panel, or Virtual Remote to
clear the alarm icon.
Video Loss
If a camera is disconnected or is damaged, the video loss icon will appear for the affected channel.
The channel number will turn WHITE.
NOTE: Once video has been restored, press the CANCEL/ESC button on the remote control, front
panel, or Virtual Remote to clear the video loss icon.
Setting Motion-only Recording
The system can record in "Motion-only" recording. During Motion-only Recording, the system
records during motion events, but will temporarily pause recording (on a particular channel)
when there is no movement.
ENABLING MOTION-ONLY RECORDING
Step 1 of 3: Enable Motion recording in the Recording schedule
1. Press the MENU button on the front panel, remote control, or virtual remote to open the main
menu.
2. From the main menu, click RECORD (
).
3. Configure the following for the channel you wish to enable motion:
• CONTI. (Continuous recording): Select OFF
• MOTION: Select ON.
• QUALITY: Select the desired video quality.
• ALARM: Select ON if you wish to enable Alarm recording.
Motion-only recording
enabled for channel 1
4. Click
18
to save your settings.
Step 2 of 3 (OPTIONAL): Configure motion detection areas
By default, the entire channel area is selected for motion recording. Follow the steps below to
customize the area of the channel that you wish to enable motion recording.
).
1. From the main menu, click CAMERA (
2. From the camera section tab, click on the camera that has motion enabled.
Select camera
3. Beside MOTION GRID, use the
buttons to select all, or select a certain
portion of the screen that will detect motion. In the motion grid, you can select the areas that
you wish to monitor for motion.
Motion Grid
Select all
Custom Select
De-select all
NOTE: If you use Custom Select, double-click the Motion Grid on the area that you wish to enable
motion. Motion activated areas highlight with a blue grid.
4. Click
19
to save your settings.
Step 3 of 3: Configuring Motion Recording frame rates
You can configure the recording frame rate when the system detects motion. For example, you
may want the system to record in a higher frame rate (30FPS) during motion recording.
1. From the Main Menu, click EVENT (
).
2. Configure the following beside the channel that has motion enabled:
• MOTION: Select the frame rate the system will record at when it detects motion (i.e 30F/S)
• Select the recording quality (LOW, MIDDLE, SUPER, HIGH, ULTRA)
Final Results
• When the system detects motion, the system begins recording as a "Motion" event. The system
records at a specific frame rate designated by the user.
• When the post-recording alarm ends, the system pauses recording in the particular channel
where motion-only recording was enabled.
• The system resumes motion-recording when it detects motion.
Setting Continuous & Motion Recording (C+M)
In Continuous and Motion recording mode, the system records 24 hours a day. But as soon as a
camera detects motion, the system records in Motion recording mode. This allows the system to
record at higher frame rates during motion recording, and mark the video as an "event".
Step 1 of 2: Enable Continuous and Motion recording
1. From the RECORD menu, configure the following on the cameras that will record in C+M:
• CONTI. (Continuous): Select the continuous recording frame rate (i.e. 15 F/S)
• MOTION: Select ON.
• QUALITY: Select the desired video quality during Motion and Alarm recording.
• ALARM: Turn ON/OFF to enable/disable Alarm recording.
• ALARM: Select ON if you wish to enable Alarm recording.
20
Recording
2. Click
to save your settings.
CONTI. is set to 30F/S.
This means Channel 2 will
record at 30 FPS during
continuous recording.
Motion is set to ON. This
means the system will
start motion recording
when the system detects
motion.
Step 2 of 2 : Configure Motion Recording frame rates
1. From the Main Menu, click EVENT (
).
2. Configure the following beside the channel that has motion enabled:
• MOTION: Select the frame rate the system will record at when it detects motion (i.e 30F/S)
• Select the recording quality (LOW, MIDDLE, SUPER, HIGH, ULTRA)
Enter the desired
recording frame rate
during Motion
recording
3. Click
Enter the image
quality during
Motion recording
to save your settings
Final Results
• The system records continuously with the assigned parameters. In this example, the system
will record at 15 FPS during continuous recording.
• When the system detects motion, Motion recording begins. In this example, the system will
record at 30 FPS when motion is detected (Motion Recording).
• When the post-alarm recording ends, Motion recording stops, and continuous recording
resumes at 15 FPS.
21
Recording
Schedule Recording
Schedule Recording can be set manually or at startup. Schedule Recording features customizable
recording parameters that you assign to each camera.
ATTENTION: Schedule Recording takes priority over all other recording modes.
Figure 8.3 Schedule Recording screen
The Schedule recording icon—
—indicates schedule recording is enabled. If you do not see the
icon, schedule recording is NOT ENABLED.
For details on setting a recording schedule, see “SCHEDULE” on page 28.
Recording Audio
The system can record one channel of audio. You must have an audio enabled camera or
self-powered microphone connected to the system in order to use this function. For details on
connected audio recording devices, see “Appendix K: Using Listen-in Audio” on page 142.
22
Playback
PLAYBACK
View recorded video on the system through playback mode.
Figure 9.0 Playback display view
To begin playback:
1. Press the WX button on the remote control. The system will play the last few minutes of the
most recently recorded video.
2. Press the following buttons on the remote control to use playback functions:
• WX: Press to switch between forward and reverse playback
•
: Press to pause playback; press repeatedly for frame-by-frame reverse playback
•
: Press to pause playback; press repeatedly for frame-by-frame forward playback
• : Press to increase reverse playback speed 1X, 2X, 4X, 8X, and 16X
• : Press to increase forward playback speed 1X, 2X, 4X, 8X, and 16X
• „: Press to stop playback and return to live viewing
23
Search
SEARCH
Search for recorded video data on the system using the Time Search menu.
To open the Time Search menu:
• Press the
button on the front panel or remote control
Figure 10.0 Time Search menu
To search for recorded video:
1. Press WX to select the month.
2. PressT to move the cursor to the calendar. The date is highlighted with a black square.
3. Press STWX to select dates with either Alarm, Motion, or Normal recordings and press
the ENTER button. The detailed Time Search menu opens.
Figure 10.1 Time Search sub-menu
4. Press STWX to select recording blocks in Hour, Minute, or Camera and then press the
ENTER button. Recording blocks are distinguished by Alarm (red), Motion (green), and
Normal (orange).
5. Use the playback buttons on the remote control or the front panel to control playback.
6. Press „ to stop playback and return to live viewing.
24
Using the Main Menu
USING THE MAIN MENU
To open the Main Menu:
• Press the MENU button on the front panel or the remote control
1
5
2
6
3
7
4
8
Figure 11.0 System Main Menu
1. DISPLAY: Adjust OSD borders, camera titles, colors, split-screen configuration, and Auto
Sequence settings.
2. CAMERA: Adjust brightness, color, contrast, title, PTZ settings, and enable/disable convert.
3. RECORD: Enable/disable recording for each camera, configure the recording quality, frame
rate, and motion.
4. SCHEDULE: Customize four kinds of recording modes according to a daily or weekly
schedule.
5. EVENT: Configure motion recording, and alarm recording settings.
6. DEVICE: Configure post recording time, key sensitivity, audio recording, and alarm settings.
7. NETWORK: Configure IP, email, and DDNS settings.
8. SYSTEM: Configure various system settings including date/time, users, Quick Setup, HDD
settings, and system information.
25
Using the Main Menu
DISPLAY
Sequential Setup
Use the Display menu to configure
the OSD and Auto Sequence
settings.
Configure Sequential Setup (Auto Sequence)
settings.
Figure 12.0 Display menu
To change display settings:
1. Select the DISPLAY SETUP tab, and
configure the following:
• STATUS BAR: Select to Show or Hide the
status bar on the OSD.
• CAMERA: Select to show the CAMERA NO. or
the CAMERA TITLE or both.
• BORDER LINE: Set the color for the borders
of the OSD: WHITE, BLACK, DARK GREY, or
GREY
• BACKGROUND: Set the background color for
disconnected cameras on the main display:
GRAY, WHITE, BLUE, or DARK GREY
• SPLIT MODE: Set up to four split-screen
display modes
• QUICK SETUP: Select ON/OFF to enable/disable
the quick setup menu. By default, Quick Setup
is OFF.
2. Press ENTER to save your changes and
exit.
Figure 12.1 Auto Sequence setup
To configure Sequential Setup settings:
1. Select the SEQUENTIAL SETUP tab and
configure the following:
• DWELL TIME: Set from 1~30 seconds.
• SEQ. MODE: Set the display mode, from single
channel full-screen to 8-channel
split-screen
NOTE: You must select one of these
display modes to enable Auto Sequence
mode. If none of these modes are
selected, Auto Sequence will not begin.
• FULL SCREEN: Select channels for
full-screen display. If selected, these
channels will appear in full-screen during
Auto Sequence mode
2. Press the ENTER button to save your
settings and enable Auto Sequence. Auto
Sequence will immediately begin.
3. Press the DISPLAY button to stop Auto
Sequence.
Auto Sequence with Front Panel and
Remote Control
Once you have configured the Auto Sequence
settings in the Display menu, you can use the
remote control to turn Auto Sequence on/off.
To enable/disable Auto Sequence:
1. Press and hold
on the front panel or
remote control for 2 seconds.
2. To exit press
. The main screen will
return to a quad display.
26
Using the Main Menu
CAMERA
Configure various camera settings,
such as brightness, contrast, title,
and covert.
3. Repeat for other camera connected to the
system.
4. Press ENTER to save your settings. Press
CANCEL/ESC to close remaining menu
windows.
CONFIGURING MOTION
Configure the motion grid and motion
sensitivity for specific channels.
NOTE: If motion detection is applied to a
camera, the system will record from that
camera only when motion is detected.
Figure 13.0 Camera menu
To configure camera settings:
1. Under CAMERA SELECTION, press WX to
select the camera.
2. Press T to configure the following:
• BRIGHTNESS, CONTRAST, COLOR: Adjust
from 0~100.
• SENSITIVITY : Select the motion sensitivity of
the system. The greater the number, the
more sensitive the system is to motion.
• MOTION GRID: Select the area of the screen
that you wish to enable motion recording.
• COVERT: Select YES/NO. If YES, the camera
channel will be obscured from live viewing to
give the impression that no camera is
recording. Use this option if the display
monitor is in public view.
NOTE: The Covert channel will use the
same background color as a
disconnected camera. To change the
background color, see “DISPLAY” on
page 26.
• TITLE: Use the alpha-numeric buttons on the
remote control to enter a name/title for the
camera. Press WX to move the cursor left/
right. If you make a mistake, press CANCEL/
ESC to return to the Main Menu and start
again.
• PTZ ID: Enter your PTZ ID (PTZ ID should
match the camera channel to which you have
connected the PTZ camera)
• PTZ MODEL: Select the model of your
connected PTZ camera (not included).
Select all
Custom Select
De-select all
Figure 14.0 Motion settings in the Camera menu.
To configure motion settings:
1. Press T to select CAMERA SELECTION
and press WX to select the camera that
you wish to configure.
2. Press T to select SENSITIVITY, and adjust
from 1~20. The higher the number, the
greater the sensitivity.
3. Press T to select MOTION GRID.
4. Select
to select the area of
the motion grid that you wish to highlight.
5. Click on the area of the grid
that you wish to enable motion
recording. A green motion
icon appears on the grid.
6. Press ENTER to save your
settings. Press CANCEL/ESC to close
remaining menu windows.
27
Using the Main Menu
RECORD
SCHEDULE
Configure recording parameters for
each channel.
Set four recording modes in a daily
or weekly schedule.
NOTE: Daily has priority over a Weekly
schedule.
Figure 15.0 Record menu
To configure recording settings:
1. Press ST to select a camera you wish to
configure.
2. Press WX to select an option and the
press + / - to configure the following:
• CONTI. (Continuous recording): Select
continuous recording frame rate (1~30 fps)
• QUALITY: Select LOW, MIDDLE, HIGH,
SUPER, and ULTRA.
• MOTION: Select ON/OFF. Motion Grid and
sensitivity must be configured in the Motion
menu. See “CONFIGURING MOTION” on
page 27.
• ALARM: Select ON or OFF to enable or disable
alarm recordings.
3. Press ENTER to save your settings. Press
CANCEL/ESC to close remaining menu
windows.
Setting Motion-only &
Continuous + Motion (C+M) Recording
• For details on how to set the system
record only when motion occurs,
see “Setting Motion-only
Recording” on page 18.
• For details on how to set the system
to record in Continuous + Motion
mode, see “Setting Continuous &
Motion Recording (C+M)” on
page 20.
28
Figure 16.0 Alarm Setup
To set a recording schedule:
1. Press WX to select MODE1 (red), MODE2
(orange), MODE3 (green), or MODE4 (blue).
2. With a mode selected, configure the
following:
• USE: Select ON/OFF. If OFF, the selected
camera(s) will not record.
• QUALITY: Select LOW, MIDDLE, HIGH,
SUPER, and ULTRA.
• RATE: Select 1, 2, 3, 4, 5, 6, 7, 10, or 15 fps.
• MOTION: Select ON/OFF. Motion Grid and
sensitivity must be configured in the Motion
menu.
3. Select the CHART tab and select ALL,
SUN, MON, TUE, WED, THU, FRI, or SAT,
and press the ENTER button or +/-. The
Schedule sub-menu opens.
4. Enter BEGIN and END times, and select
the MODE for ten time slots.
Using the Main Menu
5. Press the ENTER button to save your
settings. The Schedule sub-menu closes.
The assigned mode appears in the main
Schedule window.
6. Press CANCEL/ESC to close remaining
menu windows.
7. To enable the recording schedule, press
/ on the front panel or
on the
Virtual Remote.
Figure 16.1 Schedule recording
Stopping Scheduled Recording
If you need to stop a recording schedule, press
/ on the front panel or
on the Virtual
Remote and enter your 6-digit system
password (by default, 000000).
NOTE: Always look for the
icon in the
status bar. If you do not see the
icon,
schedule recording is NOT ENABLED.
Overnight Recording
If you want to program an overnight recording
schedule, you will need to split the time using
the available time slots in the Schedule
sub-menu.
Figure 16.2 Split the overnight recording time
2. Customize the video quality, frame rate, and
motion detection for the desired channels.
For this example, Mode 1 will have
cameras 1 and 2 set to ULTRA and 15 fps,
while the remaining cameras will be set to
HIGH and 7 fps.
3. Select the CHART tab and select MON and
then press the ENTER button. The
Schedule sub-menu opens.
4. Under BEGIN, press the number buttons on
the front panel or remote control to enter
21:00. Under END, enter 23:59.
NOTE: If using the front panel, you can select
digits by pressing + / -. You need to press + / - to
select 0.
5. Under MODE, select MODE1.
6. Press X to move the cursor to BEGIN in
the right-hand column. Enter 00:00. Under
END, enter 08:00.
7. Under MODE, select MODE1.
8. Press the ENTER button to save your
settings and return to the main Schedule
menu. Mode 1 (red) will appear in the
designated time block in the schedule.
9. Repeat steps 1~8 for Tuesday~Friday.
/ on the front panel or
on
10. Press
the Virtual Remote to enable scheduled
recording.
Example
You are a small business owner that wants
your custom recording schedule to record
from 9 PM to 8 AM, Monday to Friday.
To set the schedule:
1. From the Schedule menu, select MODE1~4.
29
EVENT
Configure recording parameters for
motion and alarm recording.
DEVICE
Configure post-recording time,
Alarm Out, Alarm Buzzer, and
alarm input settings.
NOTE: An external alarm device is not included
with the system.
Figure 17.2 Device menu
You must stop the system from recording before
you can adjust the settings in the Device menu.
Figure 17.0 Event menu
To configure Motion & Alarm settings:
1. Select the channel that you wish to
configure.
2. Under MOTION, press + / - to adjust the
frames per second (default 30 F/S). Select
the quality of the recording (select from
LOW, MIDDLE, SUPER, HIGH, and ULTRA).
3. Under ALARM, press + / - to adjust the
frames per second (default 30 F/S). Select
the quality of the recording (select from
LOW, MIDDLE, SUPER, HIGH, and ULTRA).
Press the Record button on the remote control
or from the virtual remote, and enter the system
password to stop recording.
Be sure to resume recording once you are
finished.
The GENERAL tab
The GENERAL tab allows you to configure Post
Recording time, Audio recording, Key Tone
(key "beeps"), and Key Sensitivity.
1. Configure the following in the General tab:
• POST RECORD TIME: Press + / - to enter
the post recording duration (adjust from
• AUDIO RECORD: Select ON or OFF to
enable or disable audio recording.
• KEY TONE: Select ON or OFF to enable or
disable the "beeps" when a button is
pressed.
• KEY SENSITIVITY: Press the - / + buttons
to adjust the sensitivty of the keys on the
front panel of the system.
2. Press ENTER to save your settings. Press
CANCEL/ESC to close remaining menu
windows.
30
Using the Main Menu
The ALARM tab
The ALARM tab allows you to configure the
system Alarm Buzzer and Alarm Input type on
each channel (i.e. N.O and N.C (normally open
and normally closed) settings)).
Alarm recording will take priority over
continuous recording, even if a camera is
disabled in standard recording parameters.
TIP!
If an alarm is triggered on
the system, press the
Cancel/ESC button to
cancel the buzzer (if
enabled). Cancelling the
buzzer will not stop
recording.
Figure 17.3 Alarm menu
1. Configure the following in the Alarm tab:
• RECORD CAMERA: Select ALL if you want
all the cameras to record if motion is
detected. Select 1:1 if you only want the
camera that detected motion to record.
• ALARM BUZZER: Select ON or OFF to
enable or disable the system alarm buzzer.
• ALARM OUT1: Select the type of event that
will trigger an event. Select from ALL
ALARM, ALARM IN 1~8, HDD FAIL, VIDEO
LOSS, MOTION.
• ALL ALARM: Triggers an alarm output
if the hard drive fails, if there is video
loss, motion detection, or an alarm IN
trigger.
• ALARM IN1~8: Triggers an alarm
output if a device connected to the
ALARM IN block triggers.
• HDD FAIL: Triggers an alarm if the DVR
hard drive fails.
• VIDEO LOSS: Triggers an alarm if video
loss occurs.
• MOTION: Triggers an alarm if the
camera detects motion.
• INPUT: Select the alarm type connected to
the particular channel. Select from N.O or
N.C (Normally Open, or Normally Closed).
2. Press ENTER to save your settings. Press
CANCEL/ESC to close remaining menu
windows.
31
Using the Main Menu
NETWORK
EMAIL
Configure network and DDNS
options.
Configure settings for email notification of
events on the system.
Figure 18.1 Email menu
Figure 18.0 Network menu (IP setup)
To configure IP Setup:
1. Connect an Ethernet cable to the LAN port
on the rear panel of the system.
2. Disconnect the power cable and let the
system power down for a few moments.
Reconnect the power cable. The system
automatically powers on.
3. Under CONFIG, select STATIC or DHCP.
DHCP allows you to instantly obtain an IP
address when first networking your
system. STATIC IP lets you manually enter
a fixed IP address. If you select STATIC, go
to step 4.
NOTE: DCHP allows you to quickly connect to
your network by obtaining an IP address from
the router. After the initial setup, we recommend
that you disable DHCP and set the IP address
between 1~100. For example, if your IP address
is 192.168.0.107, change the last digits to 90 (i.e.
192.163.0.90). This ensures that port forwarding
will not change in the event of power failure or
resetting of your network.
4. Press ENTER to save your settings. Press
CANCEL/ESC to close remaining menu
windows.
32
To configure email settings:
1. Under USE, select DEFAULT or SMTP (your
own email server). If you select DEFAULT,
go to step 7. If you select SMTP, go to step
2.
2. Under SMTP SERVER, enter your SMTP
email server.
3. Under SMTP PORT, enter your SMTP port.
4. Under SMTP AUTH, select ON.
5. Under SMTP USER ID, enter your SMTP
user name.
6. Under SMTP PASSWORD, enter your SMTP
password.
7. Under EMAIL ADDRESS, enter the
recipient email address for the email
notification. You can add up to five email
addresses.
8. Press ENTER to save your settings. Press
CANCEL/ESC to close remaining windows.
NOTE: When an event is triggered, you will
receive an email alert. If no events occur in
the next 5 minutes, you will no receive
another email.
If a new event is triggered during that
minutes, you will only receive the new email
5 minutes after the first email.
Using the Main Menu
DDNS
MISC
Configure Digimerge DDNS settings.
Configure additional network settings.
NOTE: You must register for the FREE
Digimerge DDNS service prior to
configuring DDNS settings.
Figure 18.3 MISC menu
Figure 18.2 DDNS menu
To configure DDNS settings:
1. Under USE, select DIGIMERGE or OFF.
2. Under DOMAIN NAME, enter only the first
portion of your DDNS domain from the
confirmation email. For example, if your
domain name is tomsmith.digimerge.net,
you only need to enter tomsmith in the text
field.
3. Under USER ID, enter your Digimerge DDNS
user name.
4. Under PASSWORD, enter your Digimerge
DDNS password.
NOTE: Obtain your Digimerge DDNS user
name and password from the confirmation
email.
5. Under DDNS TEST, select START. If
successful, you will see "GOOD." If
unsuccessful, you will see "ERROR." If you
receive an error, please check your
network connections and carefully
re-enter your Digimerge DDNS
information.
6. Press ENTER to save your settings. Press
CANCEL/ESC to close remaining windows.
To configure bandwidth settings:
1. Under BANDWIDTH, select 64 KBPS, 128
KBPS, 256 KBPS, 512 KBPS, 1 MBPS, 2 MBPS,
4 MBPS, 8 MBPS, or UNLIMITED.
NOTE: By default, the system is set to
UNLIMITED. Change the bandwidth setting
to maximize your network performance.
2. Press ENTER to save your settings. Press
CANCEL/ESC to close remaining windows.
Connecting to your system
After you have port forwarded the required
port, created a DDNS account, and enabled
DDNS on your system, you must enter the
DDNS URL into Internet Explorer to access
your DVR.
The DDNS URL must include http:// , the
name of your DDNS URL, followed by a
colon, then the port number of your DVR.
For example:
http://tomsmith.digimerge.net:80
DDNS URL
Port Number
NOTE: If you change your default port
number (port 80) to a different port, you
still need to enter your port number after
the DDNS address.
33
Using the Main Menu
SYSTEM
Configure System settings.
• PASSWORD: Select ON/OFF. If ON, the system will
prompt you for a password when opening the main
menu
NOTE: You must set the Password to
"ON" in order to use the Auto Lock.
• FACTORY DEFAULT: Select START and press the
ENTER button to restore the system to the original
factory settings
2. Press ENTER to save your settings. Press
CANCEL/ESC to close remaining windows.
TIME
For more details, on setting the date and time,
see “Recording” on page 16.
Figure 19.0 Setup menu
GENERAL
To configure general system settings:
1. Select the GENERAL tab and configure the
following:
ACCOUNT
Only the ADMIN can configure user authorities
on the system.
• AUTO LOCK: Select ON/OFF. If ON, the front panel
touch-screen will be disabled after 3 minutes of
inactivity. Enter your system password (by default,
000000) to disable.
NOTE: Auto Lock is not available if
Password is set to "OFF."
• RECORD MODE: Displays the current resolution
on the system. To edit the resolution, you must stop
the system recording. Once the DVR stops
recording, return to the System menu, and click on
the RECORD MODE field to edit the recording
resolution.
• PB INTERLACE: Select ON/OFF. If ON, image
flickering will be reduced, but overall image quality
may also be reduced. If OFF, there will be better
image quality on still images, but image flickering
during live viewing and playback.
• RUN ON BOOT: This option sets the default
recording mode when the system starts up. Select
CONTIN. REC for Continuous recording; select
SCHEDULE REC for the system to record
according to a recording schedule(s). For more
details on setting recording schedules, see see
“SCHEDULE” on page 28.
34
Figure 19.1 Account menu
To configure user and account settings:
1. Select the ACCOUNT tab, and configure
the following:
• USER: Select ADMIN or USER1~5.
• ACTIVATE: Select ON/OFF to enable the settings
for the specific user type
• AUTHORIZATION: Select MONITORING,
BACKUP, NETWORK, PLAYBACK,
CONFIGURATION, or SHUTDOWN
• PASSWORD: Enter a 6-digit password for the
user
2. Press the ENTER button to save your
settings.
Using the Main Menu
DISK
Disk Monitor
If enabled, Disk Monitor will alert you if the
internal HDD fails.
To enable/disable disk monitoring:
1. Under the DISK tab, select START/STOP.
2. Press the CANCEL/ESC button close
Auto Delete
Figure 19.2 Disk menu
Use the Disk menu to format the internal HDD,
external USB flash drive (not included),
external USB HDD, and configure Overwrite
and Disk Monitor settings.
Formatting Disks
ATTENTION: You must stop all recording
before attempting to format the internal HDD.
To format the internal HDD/external HDD/USB
flash drive:
1. Under the DISK tab, select FORMAT and
select Internal HDD, USB HDD, or USB
Memory Stick.
2. Under ACTION, select START. Formatting
begins. Once formatting is complete the
system will reset (internal HDD only).
3. Press CANCEL/ESC to close windows (USB
flash drive only).
Configure the duration the system should keep
the data on the hard drive before it is deleted.
For example, if you choose 12 hours, the
system keeps the last 12 hours of recording,
deleting the older footage.
Prerequisite
• Stop system recording (click the stop
button on the virtual remote; system
password required)
To enable auto-delete:
1. Under AUTO DELETE, select from 12 hours
~ 30 days.
2. Press the ENTER button to save your
settings.
3. Resume system recording (press the
record button on remote control or front
panel).
Overwrite
Disk overwrite will overwrite the oldest data on
the internal HDD once it full.
To enable/disable disk overwrite:
1. Under the DISK, select OVERWRITE and
select ON/OFF. If OFF, the system will stop
recording once the HDD is full.
NOTE: By default, the system is set to
overwrite.
2. Press the ENTER button to save your
settings.
35
Using the Main Menu
UPDATE
INFO
Figure 19.3 Update menu
Use the Update menu to upgrade system
firmware.
NOTE: The system supports most major
brands of USB flash drives with a capacity
of 10 MB ~ 16 GB.
To upgrade firmware:
1. Download the latest firmware update from
the Digimerge website.
2. Copy the firmware to a blank USB flash
drive.
NOTE: Do not have any folders on the USB
flash drive—just the firmware file.
3. Connect the USB flash drive to the USB
port on the front panel.
4. Stop all recording on the system.
NOTE: You must stop all recording in order
to perform the upgrade.
5. Open the Main Menu and select SYSTEM.
6. Under the UPDATE tab, select UPDATE.
7. Select START and press the ENTER button.
Firmware upgrade begins. Do not remove
the USH flash drive until the upgrade
process is complete. Do not press any
buttons or power off the system during the
upgrade process.
When upgrade is finished, press the ENTER button
in the prompt window to restart the system.
36
Figure 19.4 System Info menu
View important system information:
• LANGUAGE: The current system language
• S/W VERSION: The current system
firmware version
• DOMAIN NAME: Your Digimerge DDNS
domain name
• MAC: The physical address of the DVR on
your network
• NETWORK: The IP address of the system
• INTERNAL HDD: 1 HDD, size and space
remaining
• USB (FRONT): The status of the USB port
on the front panel
• USB (REAR):
• 4 Channel models: The status of the USB
mouse port. Note that on the 4 channel
models, the rear USB port is only used
for mouse connectivity.
• 8/16 Channel models: The status of the
USB port.
• IDE BUS: The status of the HDD—will show
"GOOD" or "ERROR"
Backup
BACKUP
Backup critical video data on your system to a USB flash drive, external USB HDD, or an external
USB CD/DVD-RW drive (not included).
NOTE: The system supports most major brands of USB flash drives with a capacity of 10 MB ~
4 GB. Most major brands of USB HDDs and CD/DVD-RW drives are supported.
USB Flash Drive
To backup recorded video:
1. Connect a blank USB flash drive to the USB
port on the front panel.
2. Format the USB flash drive if you have not
already done so. For details on formatting the
USB flash drive, see “DISK” on page 35.
3. Press the BACKUP button on the front panel.
4. Under DEVICE, make sure to select USB (FRONT
PANEL).
5. Under SELECT, select specific cameras or
select ALL. Select NORMAL, ALARM, or MOTION
recording. Select all boxes if desired.
Figure 20.0 Backup menu—USB flash drive
6. Under RANGE, enter date and time for the
system to scan for video. If the system finds a
file, it will immediately begin backing up the
data. Monitor the backup progress in the ACTION frame.
NOTE: If there is no video available in the range, the system will prompt, "STATUS: NO FILE."
7. Under ACTION, select START and press ENTER.
8. Once backup is complete, press CANCEL/ESC to close remaining windows.
9. You will be prompted to re-start recording on the system. Press CANCEL/ESC to close the
prompt, and /
Recording.
to resume Continuous Recording; press
/ to resume Schedule
37
Backup
External USB HDD
ATTENTION: You must STOP ALL RECORDING on the system prior to backing up any video data to an
external USB HDD or external USB CD/DVD-RW drive.
To backup recorded video:
1. Connect an external USB HDD to the USB port on the
front panel.
2. Format the external USB HDD if you have not already
done so. For details on formatting the external USB
HDD, see “DISK” on page 35.
3. Press the BACKUP button on the front panel.
4. Under DEVICE, make sure to select USB HDD.
5. Under SELECT, select specific cameras or select ALL.
Select NORMAL, ALARM, or MOTION recording. Select all Figure 20.1 Backup menu—USB HDD
boxes if desired.
6. Under RANGE, enter date and time for the system to
scan for video. If the system finds a file, it will immediately begin backing up the data. Monitor
the backup progress in the ACTION frame.
NOTE: If there is no video available in the range, the system will prompt, "STATUS: NO FILE."
7. Under ACTION, select START and press ENTER.
8. Once backup is complete, press CANCEL/ESC to close remaining windows.
9. You will be prompted to re-start recording on the system. Press CANCEL/ESC to close the
prompt, and /
Recording.
to resume Continuous Recording; press
/ to resume Schedule
USB CD/DVD-RW
To backup recorded video:
1. Connect an external USB CD/DVD-RW drive to the USB
port on the front panel.
2. Insert a CD/DVD-R/W disc into the drive.
3. Press the BACKUP button on the front panel.
4. Under DEVICE, make sure to select USB - CD/DVD-RW.
5. Under RANGE, enter date and time for the system to
scan for video. If the system finds a file, it will
immediately begin backing up the data. Monitor the
backup progress in the ACTION frame.
NOTE: If there is no video available in the range, the
system will prompt, "STATUS: NO FILE."
38
Figure 20.2 Backup menu—USB CD/DVD-RW
Backup
6. Under ACTION, select START and press ENTER. If your backup data spans more than one disc,
the system will eject the completed disc and prompt you to insert a new blank disc. Backup
will continue as normal.
7. Once backup is complete, press CANCEL/ESC to close remaining windows.
8. You will be prompted to re-start recording on the system. Press CANCEL/ESC to close the
prompt, and /
Recording.
to resume Continuous Recording; press
/ to resume Schedule
Time Search and Backup
Use the Time Search menu to set a Time Range, then use the Backup menu to backup critical
video to a USB flash drive, external USB HDD, or external USB CD/DVD-RW drive (not included).
To set the Time Range:
1. Press the
button on the front panel or remote control.
2. Press WX to select the month.
3. PressT to move the cursor to the calendar. The
date is highlighted with a black square.
4. Press STWX to select dates with either Alarm,
Motion, or Normal recordings and press the
ENTER button. The detailed Time Search menu
opens.
5. Press STWX to select recording blocks in Hour,
Minute, or Camera and then press the ENTER
button. Recording blocks are distinguished by
Figure 20.1 Time Search sub-menu
Alarm (red), Motion (green), and Normal (orange).
6. Press - set a START TIME. The block will turn grey.
7. Press STWX to select other blocks in your desired time range. Press + to set the END
TIME. All the block in the time range will turn grey.
8. Press CANCEL/ESC to exit.
To backup video:
1. Press the BACKUP button on the front panel.
2. Under DEVICE, make sure to select USB (FRONT) MEMORY STICK, USB - HDD, or USB - CD/DVD-RW.
3. Under SELECT, select specific cameras or select ALL.
Select NORMAL, ALARM, or MOTION recording. Select
all boxes if desired.
4. Under RANGE, the START and END TIMES you select in
the Time Search menu should appear.
5. Under ACTION, select START and press ENTER.
6. Once backup is complete, press CANCEL/ESC to close
remaining windows.
Figure 20.2 Backup menu
39
Backup
Viewing Backup Video
Along with copying the files, the system adds a Backup Video Player (McdPlayer) and an AVI
converter to the USB flash drive, external HDD, and external USB CD/DVD-RW drive. Use the
Video Player to view the backed up video files on your PC.
NOTE: You can also view the files using the browser-based remote surveillance software.
To view backup video:
1. Connect the USB flash drive or external USB
HDD with the backed up video data to your PC;
or insert the CD/DVD-R/W disc into your PC’s
CD/DVD-RW drive.
2. McdPlayer should launch automatically. If
Autorun does not start, search the drive/disc
and double-click mcdplayer.exe to launch the
Backup Video Player. McdPlayer launches and
begins to load your backed up video. For more
details, see “Viewing Backup Video” on
page 40.
Figure 20.3 Backup video player file
NOTE: If the drive contains more than one video
file, first select the file and click OK.
3. When the purple progress bar has loaded, you
can begin to playback the video.
Figure 20.4 Playback in McdPlayer
NOTE: The "C" button stands
for Capture. The "D" button
stands for de-interlace.
40
Backup
Using MCD Player
MCD Player is a small application that the system places on your USB flash drive when you backup
critical video.
To use MCD Player:
1. Connect the USB flash drive or external HDD with the backed up video data to your PC; or
insert the CD/DVD-R/W disc into your PC’s CD/DVD-RW drive.
2. Double-click mcdplayer.exe to launch the Backup Video Player. The Video Player launches and
begins to load your backed up video.
NOTE: If the drive contains more than one video file, first select the file and click OK.
Figure 20.5 McdPlayer main window (image simulated)
3. When the purple progress bar has loaded, you can begin to playback the video.
4. Use the playback buttons at the top of the main screen to control playback.
•
•
•
•
: Reverse playback -4X
: Reverse playback -2X
: Reverse playback -1X
: Backward step (frame-by-frame)
•
•
•
•
: Forward step (frame-by-frame)
: Forward play 1X
: Forward play 2X
: Forward play 4x
5. To view full-screen, click the number buttons. Click the split-screen buttons to view Quad and
multi Split-Screen.
6. Click and drag the purple playback slider to pause, advance or restart playback.
7. Click W to for a watermark on the file. If the file has a watermark, the following prompt will
appear: "Has not been tampered with."
8. Click the PRINT ICON to immediately print a still frame from the video to your default printer.
NOTE: The date and time will appear below the printed image.
41
Backup
42
CMS-DH CENTRAL MANAGEMENT SOFTWARE
CMS-DH is a central management software that allows you to view and manage up to 300 DH200
series DVRs.
System Requirements
Your system must meet the system requirements below:
Minimum system requirements
Recommended system requirements
• Windows XP SP 1
• Windows XP SP 1
• Pentium 4, 2.4Ghz
• Pentium 4, 3.0 Ghz
• 512 MB RAM
• 1GB RAM
• 64 MB AGP video card
• 256 MB, PCI-E video card
• 1024 x 768 monitor resolution
• 1600 x 1200 monitor resolution
• Direct X 7.0
• Direct X 9.0
• 100MB Ethernet LAN
• 100MB Ethernet LAN
• 10 GB free storage space
• 40 GB free storage space
Prerequisites
• Port forward port 80 (default port) to the router that the DVR is connected to
• Create a DDNS account
• Enable DDNS in the DVR
• Enter the DDNS information into the DVR
• DVR must have access to the Internet or Local Area Network (LAN)
43
CMS-DH Central Management Software
Installing CMS-DH
To install CMS-DH:
1. Locate the CMS-DH software included with the software CD.
2. Double-click the CMS-DH setup file.
NOTE: You may receive installation warnings.This is normal. Accept the security warnings to
continue.
3. Follow the on-screen instructions to install the software.
4. Click Yes to restart the computer when prompted.
44
Starting CMS-DH
To start CMS-DH:
• Double-click the CMS-DH icon (
) on the desktop.
Adding a DVR from the local area network (LAN)
Once you open CMS-DH, you can add a DVR.
To add a DVR to CMS-DH:
1. Click Device.
Device
2. Click Scan to locate connected DVRs on the network.
DVRs that were discovered on the LAN
NOTE: By default, when
adding a DVR from the LAN,
the DVR name will
automatically be named the
last 3 digits of the IP address.
Scan button
45
CMS-DH Central Management Software
3. Click on the DVR you wish to add to CMS-DH, and then click Apply>OK.
• The DVR appears on the left panel.
Apply
Ok
If you have changed the default password of the DVR,
you must select the DVR from the list, then manually
re-enter the new password in the Password field, and
then click Apply and then OK.
4. Click on the DVR you want to connect, and click the Offline button.
2. Click the Offline button
1. Select the DVR you want to connect.
5. Double-click the name of the DVR to connect to the system.
Double-click to connect to DVR
NOTE: To add another DVR from the network, you must click the Online button to disconnect
the DVR. Then repeat steps 1-5 to add the new DVR.
46
Adding a DVR using a DDNS address
If you have DVR systems that have DDNS set up, you can add them to CMS-DH.
Prerequisites
• Create a DDNS account.
• Enter the DDNS information into the DVR locally.
• Port forward the required port (default, port 80) to the router.
To add a DVR using a DDNS address:
1. Make sure the DVRs have been disconnected from CMS-DH. Click Device.
Device
2. In the Device manager window, click Add.
Add
3. Beside the Type drop-down menu, select DVR.
47
CMS-DH Central Management Software
4. Enter the following into the blank fields:
• Name: Enter the DVR name of your choice.
• IP/DDNS: Enter the DVR’s DDNS address (for example tomsmith.digimerge.net)
• Port: Enter the DVR’s port number (by default, port 80)
• User:Enter the DVR’s user name (by default, admin)
• Password:Enter the DVR’s password (by default, 000000)
Enter the DVR name
Enter the DVR’s Port number
Enter the DVR’s
DDNS address
Enter the DVR’s user name
Enter the DVR’s password
5. Click Apply>Ok.
Apply
48
Ok
CMS-DH Central Management Software
6. Click the Offline button to connect to the DVR. Double-click the DVR icon to begin viewing.
1. Click the Offline button
2. Double-click DVR icon
Final Result
Once you have added the DVR, you can add multiple DVRs and view them in the tab. To switch DVR,
click on the tabs near the top of the window.
Click the tab to switch DVR
49
Adding a Virtual DVR
A virtual DVR allows you to add video sources from multiple DVRs, into one main window.
Example
In the example below, multiple video sources from two DVRs are grouped into
the Virtual DVR.
DVR # 1
DVR # 2
1 2
4 5
7 8
3
A
3
B
Video feed from DVR #1
6
D
4
A B C
D E F
8
G
C
G
6
9
H I
Video feed from DVR #2
Virtual DVR
(Combined video feeds from DVR #1 & DVR #2)
Prerequisites
• Ensure the DVRs are online, and connected to CMS-DH.
To add a Virtual DVR:
1. Click the New VDVR button (
).
50
CMS-DH Central Management Software
2. Double-click the virtual DVR icon in the tree menu on the left.
Virtual DVR icon
3. Click the + symbol to expand the DVR menu tree.
Click the + symbol to
expand menu tree
4. Drag the desired camera into the Virtual DVR window.
NOTE: You can drag the camera into any desired channel in the virtual DVR.
Example
Drag
Drag
Drag
5. Repeat step 3-4 as required for different DVRs.
51
CMS-DH Central Management Software
Creating New Group Folders & Sub folders
Creating group folders and sub-folders helps you organize multiple DVRs. For example, you can
create a new folder for each different DVR.
To create group folders:
1. Right-click on the Group folder, then click New Group.
New Group folder
2. Drag the desired DVR into the new folder.
To create a sub-group:
• Right-click on the Group folder, then click New sub group.
52
CMS-DH Central Management Software
Configuring General System Settings
To configure general system settings:
1. Open CMS-DH to access the Login window and then click Setup (Or, click File> Setup once
you are logged in to CMS DH)
Setup
2. Configure the following in the Setup menu:
• OSD Setup: Configure the on-screen display items that you want to appear in the channel
(i.e. camera name, time, frame rate etc.).
• Password: Change the CMS-DH login name and password. Enter your desired ID (user name)
and password, and then click OK to save your settings.
• Miscellaneous: Select the items you wish to enable:
• Check Watermark: Checks the system screenshots to ensure that they have not been
tampered.
• Keep Opened Window: Automatically re-opens the windows that were closed after you
restart the program.
• E-Map Link Event: When selected, the E-map will open pop-up windows when an event
occurs (setup required).
• De-interlace: Enable De-interlace to reduce "feathering" effect of video playback.
• Sequence Time: Enter the sequence time of each DVR.
• Alert Window Time: Enter the amount of time the Alert window remains on screen.
• Video Standard: Select from NTSC or PAL video output.
• Video Render: Select the DirectX type of your system. Select VMR7 if your system uses Direct
X 7.0. Select VMR9 if your system uses Direct X 9.0.
• Video Channel: Select the maximum amount of DVR channels that the software displays.
Choose Max 16 for 16 maximum channels, Max 64 for 64 maximum channels.
• Download Folder: Select the download destination on your hard drive. The download folder
stores saved videos and images. Click the browse button (
directory.
) to select the default download
53
Adding Users
You can add multiple users to CMS-DH, specifying the DVR menus that each user is allowed to
access.
To add a new user:
1. Log in to CMS-DH.
2. Click File>CMS-DH Account.
3. Enter the following:
• ID: Enter the desired user name.
• Password: Enter the desired user password.
• Confirm Password: Re-enter the user password.
Select the DVR the user will have access to
Select the menus the user will have access to
Add
OK
4. Under the DVR list, click the checkbox to select the DVR the user will have access to.
5. Under ’Uses’ click the checkbox to select the type of menus the user will have access to.
6. Click Add and then click OK to save your settings.
To remove a user:
1.
2.
3.
4.
54
Log in to CMS-DH as the administrator (default user name: admin, default password: 0)
Click File>CMS-DH Account.
Click the user name that you wish to remove.
Click the Del button to remove the user.
Recording Video to the hard drive
CMS-DH allows you to record video to your local hard drive. The amount of video that you can
record depends on the size of your computer’s hard drive.
To record video:
). The Rec button turns red.
1. During live view, click the Rec button (
NOTE: If you want to capture a single channel of video, double-click the channel to view the
channel in full screen mode, then click the Rec button.
NOTE: If you want to capture all channels, ensure that you are viewing the DVR in split screen
mode, and then click the Rec button.
) again to stop recording.
2. Click the Rec button (
NOTE: The file is saved into the default save directory of the CMS-DH software. To locate the
save directory of the video files, click File>Setup, and look under Download Folder to determine
where the file is saved.
55
Playing back recorded video
The video is saved as a proprietary file that is playable only by CMS-DH.
To play back previously recorded video files:
1. From the main window, click File>File Playback.
2. Click the Open button.
Open button
3. Select the desired file you wish to play and click Open.
Open button
4. Use the video playback controls to watch the video.
56
CMS-DH Central Management Software
Remote Search
Remote search allows you to search for archived video on the DVR.
Prerequisite
• Ensure you are connected to the DVR that you wish to search from.
To search for video:
1. Right-click on the DVR that you wish to search video from, then click Remote Search.
2. To search for the video:
a. Click
to select the desired month.
b. Select the date of the video.
c. Select the hour.
d. Select the minute.
A
C
D
B
Play button
3. Click the Play button to begin watching the video.
57
CMS-DH Central Management Software
Video Playback Controls
Once the video begins to play, use the video controls to manipulate video playback.
Use the playback controls to control video speed
Select hour
Select minute
Video speed slider
Local Search
Local search allows you to search for video stored locally on the computer hard drive.
Prerequisite
Ensure you are connected to the DVR that you wish to search from.
To search for videos stored on your hard drive:
1. Right-click on the DVR that you wish to search video from, then click Local Search.
58
2. To search for the video:
a. Click
to select the desired month.
b. Select the date of the video.
c. Select the hour.
d. Select the minute
A
C
D
B
Play button
3. Click the Play button to begin watching the video.
Saving Video Files
You can save the proprietary video files to your local hard drive from the Search menu. The video
file ends in a .cms extension, and requires CMS-DH for playback.
To save video files from the search menu:
1. Select the month, date, and time of the video.
Save As button
2. Click the Save As button.
3. Select the desired save directory, and click OK to save the file.
59
Converting video files to AVI
Converting proprietary .CMS video files to AVI allows you to play the video on a computer that does
not have the CMS-DH software.
NOTE: To convert video files without using CMS-DH, you can also use the standalone DVI video
converter. For details, see “Appendix L: Converting Video Files to AVI” on page 143.
Prerequisite
• Make sure that you are in the Local Search menu (Right-click on the DVR, and click Local
Search)
To convert video files to .AVI:
1. Select the month, date, and time of the video.
Select camera
checkbox
AVI Convert button
2. Select the checkbox beside the camera you wish to back up video from.
3. Click the browse button (
) and select the file output directory.
4. Click the AVI Convert button.
• CMS-DH converts the file, and stores it in the output directory.
Click the browse
button to select
save directory
60
CMS-DH Central Management Software
Schedule Recording
To enable/disable schedule recording:
1. Right-click on the DVR you wish to configure and then click Control>Schedule>Start / Stop
• Click Start to enable schedule recording. Click Stop to stop schedule recording.
Schedule Backup
You can schedule regular backup of video to your local hard drive. The schedule can be configured
to back up 24 hours of video, or during a specified time only.
Prerequisite
• 3GB of hard drive space (backup will not function if there is less than 3GB)
• DVRs must be in offline mode
To configure Schedule Backup settings:
1. Click the DVR that you wish to configure.
2. Click the Device button (
).
Device button
61
3. Select On to enable schedule backup.
Select channels you wish to back up
4. Select Daily to back up 24 hours of video to your hard drive. Go to step 6.
• Select Hourly to back up every hour of video to your hard drive. Go to step 5.
5. In the Minute drop-down menu, enter how many minutes the system should wait before
recording. For example, if you enter 10 minutes, the system will backup video footage from
8:10 a.m to 9:10 a.m.
6. In the Hour drop-down menu, enter the time you wish to begin backup. For example, if you
enter 5:00pm (05:00hr), the backup will start at 5:00pm, and end at 4:49am (the next day).
Enter the hourly time in 24-hour format.
7. Select the channels that you wish to enable schedule backup.
Select channels you wish to back up
8. Click Apply and then click OK to save your settings.
62
CMS-DH Central Management Software
Taking Screen Captures
You can capture screen shots as JPeg or Bitmap images (JPG or BMP).
To take a screen capture:
1. During live view, click Capture (
).
Click the Print button to print the
image to a printer.
2. Click the Save As button. Enter the desired picture name, and select the desired save
directory, and then click Save.
NOTE: To take a screen capture of a full-screen, double-click the desired channel, then click
the Capture button.
Viewing File Download Status
To check the download status of your video files:
1. Connect to the DVR you wish to check the video status on.
2. Click on Tools>Download>Status.
3. To cancel the download, click Cancel.
63
Changing viewing modes
To change the viewing modes of CMS-DH:
1. Log in to CMS-DH, and connect to a DVR.
2. Click (
)to change the viewing mode (single-channel, quad-channel etc).
Click to change viewing modes
Sequencing
If you monitor multiple DVRs, you can have each tab change continuously. This process is called
sequencing. You can perform sequencing as long as you have two or more DVRs. Virtual DVR’s
work with sequencing as well.
Prerequisite
• Log in to two or more DVRs
To start a sequence:
• Click the Sequence button (
).
Sequence button
The two DVR tabs will continually switch between eachother
NOTE: To change the sequence time, click File>Setup. Under "Miscellaneous", enter the
desired sequence time in seconds, and click Ok.
64
CMS-DH Central Management Software
E-Map
The E-Map feature allows you to visually map your cameras over a Jpeg image.
Example
Camera list
From the camera list, you can drag
the camera icon over the Jpeg image
Jpeg image of a house blueprint
Prerequisite
• Ensure the DVRs are online.
To set up an E-Map:
1. Click the E-Map button (
).
E-Map button
65
2. Click File>Background. Locate the file you wish to import, and then click Open.
3. Drag the desired cameras from the camera list, over the image.
TIP: You can also drag the DVR icon and E-MAP icon over the image.
Drag
Drag
Tip:
To rotate the camera, right-click on the
camera, and click Rotate.
Click the desired turning position to rotate the
camera icon.
E-Map Setup
To configure the E-Map setup menu:
1. Click File>E-Map Setup.
2. Configure the following:
• Title: Change the camera title.
• Show Description: Show/hide camera name.
• Lock: Locks the camera position.
• Description color: Change e-map font color.
3. Click Ok to save your settings.
66
CMS-DH Central Management Software
Viewing video on E-Map
Once you have mapped your cameras on E-Map, you can view, and search channels from the
E-Map directly.
To view live video on E-Map:
• Double-click on the desired camera icon to open live view.
Live channel
Configuring E-Map camera settings
To configure E-Map camera settings:
1. Right-click on the camera you wish to
configure.
2. Configure the following:
• Description Edit: Edit the camera
name on the E-Map.
• Remote Search: Opens the video
search menu.
• Live: Opens a live view window of the
camera.
• Property: View DVR properties.
Right-click on the camera to open camera
sub-menu options.
• Rotate: Rotates the camera icon in the
E-Map.
67
CMS-DH Central Management Software
Zooming into the E-Map
• To zoom into the E-Map, click the Zoom In / Zoom Out buttons (
).
Zoom In/ Zoom Out
Removing camera icon in the E-Map
• Select the camera icon in the e-map, and click the Remove Item button (
).
Remove Item
Adding Multiple E-Maps
To add multiple E-Maps:
• Right-click the Group folder, and click New E-Map.
To remove the E-Map:
• Right-click on the E-Map, and then click Remove.
Tip: After you have created a second E-Map, you can drag the E-Map icon over a Jpeg image in the
E-Map.
68
CMS-DH Central Management Software
Viewing DVR Health
To view the status of the DVR:
1. Select the DVR on the menu tree on the left.
2. Click the Health button (
).
Closing windows
To close open tabs:
• Click the Close button, and select Close or Close All.
Locking Windows
• To prevent the tab from being dragged, click the Tab Unlock button.
69
CMS-DH Central Management Software
DVR Log
The DVR log allows you to check events that occurred in the DVR, such as hard drive malfunction,
video loss, motion detection, and alarm settings.
To access the DVR log:
1. Connect to the DVR that you wish to view the log from.
2. Right-click on the DVR, and click Log.
3. Configure the following:
• Begin & End: Specify the start and end date and time.
• Query: Select the event type you wish to search for
Enter the start and stop
date and time
Select an event type from
the drop-down menu
Search button
4. Click Search to populate results.
NOTE: Select the event and click the Export button to export the log as a text file. The log allows
you to see any events logged by the DVR (i.e motion loss etc.).
70
CMS-DH Central Management Software
CMS-DH System Log
The CMS-DH log allows you to view video events that occurred in the system (i.e motion and
camera loss events).
Prerequisite:
• Ensure the DVR(s) are online and connected to CMS-DH
To view the system log:
1. Click the CMS-DH Log button (
).
CMS-DH Log button
2. Configure the following settings:
• Begin: Enter the Month, Date, Year, and time you wish to begin to search the log.
• End: Enter the Month, Date, Year, and time you wish the log search to stop.
• Channel: Enter the channel number you wish to search.
Begin / End
Playback screen
Channel
Playback controls
Search results
Search button
3. Click the Search button.
• A list of results populate. Double-click the event in the search results to begin event playback.
Use the playback controls to control playback speed.
71
CMS-DH Central Management Software
PTZ
To activate the PTZ control, click the PTZ button (
).
NOTE: You must select the channel that has a PTZ camera before using PTZ controls.
Pan & Tilt
Zoom Out
Zoom In
Focus In
Focus Out
Auto Focus
Open Iris
Close Iris
Auto Iris
Save Preset
Go to Preset
Auto Tour
Custom 1
Custom 3
Custom 2
Auto Pan
Auto Tilt
Auto Pan
Menu Call
Escape
Speed Down
Speed Up
PTZ Power
Setting PTZ Pre-Sets
1. Click the Pan & Tilt buttons to move the camera to the desired position.
2. Click the Save Preset button (
and then click Ok.
). Enter the desired pre-set number (between 0 - 9999)
To access a pre-set
• Click the Go to Preset button (
72
). Enter the pre-set number, and then click Ok.
CMS-DH Central Management Software
System Setup
To access the full system setup menu:
1. Right-click on the DVR you wish to configure.
Setup
2. Click Setup from the sub-menu to access the full Setup menu.
NOTE: The menu structure is identical to the menu structure on the local DVR.
73
CMS-DH Central Management Software
Upgrading the firmware remotely (DH200+ Series only)
Prerequisite
• Ensure the DVRs are online
• Download the firmware from www.digimerge.com, and extract the firmware file
To upgrade the DVR firmware using CMS-DH:
1. Right-click on the DVR that you wish to upgrade the firmware.
2. Click on Control>DVR Setup>Update.
3. Under Image File, click the browse button (
). Locate the firmware file and then click
Open.
NOTE: The firmware file ends in a .IMG extension.
4. Click Start to upgrade the system firmware. Wait for the system prompt before you close teh
window.
NOTE: Do not exit CMS-DH during the firmware upgrade process. Doing so may corrupt the DVR.
74
CMS-DH Central Management Software
Configuring Post Event Action Tab
The Post Event Action tab allows your system to alert you when an alarm event triggers the DVR.
For example, when the system detects motion from an input device, the computer speakers plays
a sound to alert you. Or, you can have the CMS-DH software alert you with a pop-up window when
motion is detected.
Setting up Post Event Actions on a NO/NC Device
Prerequisites (If setting up NO/NC Devices)
• Connect the input device into the alarm block in the rear panel of the DVR.
• Ensure you have the correct settings for the device (N/O , N/C), and that you have correctly
configured the settings in the DVR menu.
• Ensure the DVRs are online.
To configure the Post Event Action tab:
1. Expand the menu tree under the desired DVR that you wish to configure.
2. Under Alarm Input, right-click the number block that your device is connected into.
3. Click Post Event Action.
Right-click on
the device you
wish to
configure
4. Configure the following:
• Events: Select Alarm Input ON or Alarm Input OFF
• Command: Select from Play Sound or None.
75
CMS-DH Central Management Software
• Parameter: Select the desired alert sound you want the computer to play.
Click here to configure the Command
and Parameter settings
5.
6.
7.
8.
Click Apply and then OK to save your settings.
Under Alarm Output, right-click the light bulb icon, and click Control.
Click Alarm Output On or Alarm Output Off. This depends on your device type (N/O or N/C).
Click Apply and then OK to save your settings.
When an alarm is triggered, the system will play a sound on the computer.
Configuring Alarm Output
To configure the alarm output type:
1. Under Alarm Output, right-click the light bulb icon, and click Control.
2. Click Alarm output on to enable the alarm out device, or Alarm output off to disable the
alarm out device
76
CMS-DH Central Management Software
Setting message pop-up notifications
You can configure CMS-DH to produce message pop-up windows when an event occurs.
To configure CMS-DH to produce message pop-up events:
1. Expand the menu tree under the desired DVR that you wish to configure.
2. Right-click on the camera you wish to set alerts for, and click Post Event Action.
3. In the Events drop-down menu, select the type of event that will trigger CMS-DH to produce a
pop-up window when an event is detected.
4. In the Device drop-down menu, select the System.
5. Under the Sub Type drop-down menu, select Window. Under the Command drop-down menu,
select Alert Window.
6. Click Apply and then click OK.
77
CMS-DH Central Management Software
Result
When the camera detects motion, a pop-up window appears on the bottom-right corner of the
screen to alert you.
Setting Video pop-up notifications
You can configure CMS-DH to produce video pop-up windows when an event occurs.
To configure CMS-DH to produce video pop-up events:
1. Expand the menu tree under the desired DVR that you wish to configure.
2. Right-click on the camera you wish to set alerts for, and click Post Event Action.
78
CMS-DH Central Management Software
3. In the Events drop-down menu, select the type of event that will trigger CMS-DH to produce a
pop-up window when an event is detected.
4. In the Device drop-down menu, select the name of your DVR.
5. Under the Sub Type drop-down menu, select Camera.
6. Under Sub No., select the channel number you wish to appear as a pop-up alert.
7. Under Command, select Live Video.
8. Click Apply and then click OK to save your settings.
Result
When the camera detects motion, a pop-up window appears with live video.
79
CMS-DH Central Management Software
Configuring other Post Action Events
Under the Command drop-down menu, there are several commands that CMS-DH can output.
• GoTo PTZ: Opens the PTZ camera.
• Auto Tour: Opens the PTZ camera and starts the Auto Tour.
• Auto Pan: Opens the PTZ camera and starts the Auto Pan feature.
• Auto Tilt: Opens the PTZ camera and causes the PTZ camera to Auto Tilt.
• Live: Opens a live video window.
• Record: Begins live recording.
POS Data Search
The POS Data Search function is not available for the DH200+ series.
POS data search
80
CMS-DH Central Management Software
Running CMS-DH on multiple monitors
CMS-DH can support a maximum of 8 monitors on a single system. Running 8 monitors is
extremely resource intensive. The recommended system specifications is listed below. If your
system does not meet the requirements below, you may experience slow system performance.
Minimum system recommendations to run CMS-DH on multiple monitors
• Intel Core i5 or i7 processor
• 6 GB of RAM
• A motherboard that can support up to four (4) PCI-E video cards
• Geforce 9500 GT video card,1GB or greater
To run CMS-DH on multiple monitors:
1. Connect to CMS-DH. Open the desired DVR’s / E-Maps etc. that you wish to view.
2. Drag the desired tabs to a different monitor.
Drag the tab out to move it into a different screen.
3. Repeat as required.
Final Result
81
iSMS Client (Remote Viewing on the Mac)
iSMS Client (Remote Viewing on the Mac)
The iSMS Client allows you to remotely connect and configure your DH200 Series DVR using the
Safari browser in Mac OSX 10.6.
System Requirements
Your system must meet or exceed the requirements below before installing the iSMS Client:
• Operating System: Mac OSX 10.6 or later
• CPU: Intel Core Duo series CPU or higher
• Memory (RAM): 1024 GB
• Video Card memory: 256 MB
• Free Hard Drive space: 2GB
• Video Resolution: 1024 x 768
Prerequisites
• Download the iSMS client from www.digimerge.com, under the DH200 product page
• Port 80 (or whichever port your system is using) must be port forwarded to your router
• You must create a DDNS account, and have the DDNS settings configured in your DVR
• The DVR must have internet access
• You must have a Digimerge DDNS address to log in remotely
Installation Steps
To install the iSMS Client:
1. Double-click on the iSMS Client icon.
2. Follow the on-screen instructions to install the software. Enter your password
when prompted to install the software.
Double-click to start
installation
82
Enter the admin password
when prompted
Using the iSMS Client
Using the iSMS Client
To open the iSMS client:
1. Locate the iSMS program in the Applications folder.
2. Double-click the iSMS icon(
)to start the program. The iSMS login window opens.
Note
Enter the DVR’s DDNS address here
The iSMS client supports a
maximum of three (3)
connected users.
File Open button
Click to change save directory
To log in to your DVR remotely:
1. In the Host Port field, enter the DDNS address of your DVR in full, including the port number.
(i.e. tomsmith.digimerge.net:80)
2. In the User Name field, enter admin.
3. In the Password field, enter your DVR password (by default, 000000)
4. Click Connect to log in to the system.
To change the save directory:
1. Click the directory name under "Backup".
2. Select the desired save directory.
3. Click Open to apply your changes.
To delete an account:
1. Select the DDNS address beside the Host Port drop-down menu.
2. Click the Delete button to remove the account.
To view a previously saved video on the hard drive:
1. Click the File Open button.
2. Locate the directory of the video. Select the video and then click Open to begin video playback.
83
Using the iSMS Client
iSMS Interface
The iSMS Interface displays all connected channels of your DVR.
1. Channel numbers
2. Viewing Modes
3. PTZ Menu 4. Screen Capture
5. Hide menu button
6. Record
7. Main Viewing window
1.
2.
3.
4.
Channel Numbers: Click the desired channel to view in full screen.
Viewing Modes: Click the icons to switch viewing modes (i.e split screen, quad-view)
PTZ Menu: Opens the PTZ menu.
Screen Capture: Takes a picture of the main viewing window, and saves it to the hard drive to
the save directory you specifiy.
5. Hide Menu button: Collapses the tool bar and hides the interface functions.
6. Record: Click to record video of the selected channel. Click again to stop recording. The file
saves to the directory you specify.
84
Using the iSMS Client
To take a screen capture:
1. Click the Screen Capture button (
).
2. Enter an image name into the blank field, and then click Save or click Print.
Enter image name
To record live video:
1. Click the Record button (
). The record button turns red (
2. Click the Record button again to stop the recording.
).
NOTE: The video file saves into a folder to the save directory you specify.
To view recorded video:
1. In the tool bar, click DVR>File Play.
2. Locate the video file on your hard drive.
• The video file ends in a .cms extension.
A video save folder looks similar to the image above.
3. Click Open to view your saved file.
85
Using the iSMS Client
Configuring OSD Settings
The iSMS interface can be customized to show less or more information.
To configure the iSMS display settings:
1. From the tool bar, click iSMS>Preferences.
2. Select the display settings that you wish to remove by clicking the checkboxes.
3. Close the menu to save your settings.
Searching for video remotely
You can search for video from your DVR remotely, and back up the file to your local hard drive.
To search for video on your DVR remotely:
1. From the tool bar, click DVR>Remote Search.
2. From the Remote Search menu, perform the following:
a. Select the Month/Year
b. From the Calendar, select the date
c. Select the Hour and Minute
d. Select the channels you wish to search under by clicking the check boxes
86
Using the iSMS Client
Hour
Month /
Year
Minute
Calendar
Download
Playback
Channel selection
5. Click the Playback button to begin viewing.
OR
Click the Download button to save the video to your default save directory.
Download Progress bar
During video download, the status bar indicates the progress of the saved video.
87
Using the iSMS Client
Playback Window
Playback controls
• Use the Playback Controls to manipulate video speed
Drag the video slider to skip through the video
Play
Fast Forward
Reverse Step (1 frame)
Rewind
88
Forward Step (1 frame)
• Click the Rewind or Fast
Forward buttons repeatedly
to increase the speed
• The Reverse Step and
Forward step button
advances the video by
one frame
Using the iSMS Client
Searching for video locally
To search for local videos saved on your hard drive:
1. From the toolbar, click DVR>Local Search.
2. From the Remote Search menu, perform the following:
a. Select the Month/Year .
b. From the Calendar, select the date.
c. Select the Hour and Minute
d. Select the channels you wish to search under by clicking the check boxes
Hour
Month /
Year
Minute
Calendar
Playback
Channel selection
5. Click the Playback button to begin viewing. The Playback window opens.
89
Using the iSMS Client
Configuring PTZ settings
If your DVR has a PTZ (pan tilt zoom) camera installed, you can control the PTZ camera through
the PTZ menu.
To open the PTZ menu:
• Click
from the main interface.
PTZ Controls
To control your PTZ camera, click on the channel that your PTZ camera is connected to.
90
Using the iSMS Client
PTZ Controls cont’d.
91
Using the iSMS Client
Configuring PTZ Protocols in the iSMS Client
You must enter the PTZ camera protocols and settings in the iSMS client before you can control
the PTZ camera.
To configure PTZ camera settings:
1. From the toolbar, click DVR>Setup.
2. From the Setup window, click Camera.
Camera
3. Click the channel with the PTZ camera.
Select channel with PTZ camera
Select PTZ protocol
P/T/Z ID
4. In the P/T/Z Model drop-down menu, select the PTZ protocol of your camera.
NOTE: Consult your PTZ camera manual for protocol details.
5. In the P/T/Z ID field, enter the PTZ ID of your PTZ camera.
6. Click Apply to save your settings.
92
Configuring the iSMS Client
Configuring the iSMS Client
The iSMS client features a Setup menu that allows you to configure settings in your DVR remotely.
The following menus are available for configuration:
• Display
• Camera
• Motion
• Record
• Alarm
• Schedule
• Network
• System
To open the Setup Menu:
• From the toolbar, click DVR>Setup.
• Click the appropriate Menu icons to configure the system.
NOTE: For details on configuring the DVR settings, consult the DH200
owner’s manual. The menus in the iSMS client are identical to
the local DVR menu.
93
Digi Imobile Touch - iPhone App
DIGI IMOBILE TOUCH - IPHONE APP
Digi iMobile Touch is an iPhone app that allows you to remotely view your DH200+ series DVR.
There are two versions of the Digi iMobile Touch app :
1. Digi iMobile Touch Lite (Free)
2. Digi iMobile Touch Pro (Payment required)
Digi iMobile Touch Lite VS Digi iMobile Touch Pro
Feature
Lite version
Pro version
Channels supported
16
16
Video Search feature
No
Yes
Record On/Off control
No
Yes
Schedule On/Off control
No
Yes
Alarm On/Off control
No
Yes
Number of DVRs Supported
2
10
Price
Free
$9.99 from the
Apple App Store*
*Prices subject to change. Please check the Apple App Store for the latest pricing.
Compatible Devices
• iPhone 3GS, iPhone 4, iPod Touch (3rd and 4th generation), iPad
• iOS 4.1 or later
• Digimerge DH200/200+/230/250 Series DVR
94
Digi Imobile Touch - iPhone App
Prerequisites
• Port 80 (or whichever port your system is using) must be port forwarded to your router
• You must create a DDNS account, and have the DDNS settings configured in your DVR
• The DVR must have internet access
• You must have a Digimerge DDNS address to log in remotely
• An iTunes account
NOTE: You will need to create an iTunes account before you can download the app. An iTunes
store account requires a valid credit card number. Your credit card number will be
charged if you download Digi iMobile Touch PRO. The Digi iMobile Touch Lite app is free
of charge.
Installation Steps
1. Search for Digi iMobile Touch Lite or Digi iMobile Touch Pro in the iTunes store. Follow the
onscreen instructions to install the app.
Digi iMobile Touch Lite
FREE
Search for Digi iMobile Touch Lite
Digi iMobile Touch Pro
$9.99
Search for Digi iMobile Touch Pro
Starting Digi iMobile Touch
• Tap on the Digi iMobile Touch Lite / Pro icon (
) to start the app.
95
Digi Imobile Touch - iPhone App
Configuring Digi iMobile Touch Lite/Pro
Once you have installed the application, enter your DVR‘s information to connect remotely.
To enter your DVR information into Digi iMobile Touch Lite:
1. Tap the + button.
+ button
Digi iMobile Touch Lite users:
You can add a maximum of two
(2) DVRs to the Device list.
Digi iMobile Touch Pro users:
You can add a maximum of ten
(10) DVRs to the Device list.
2. Enter the following:
• Name: Enter the DVR name of your choice.
• IP/Host:
• Enter the local IP of the DVR, followed by a colon, folowed by the DVR’s port number
OR
• Enter the DDNS address of the DVR, followed by a colon, followed by the DVR’s port
number (i.e. touch.digimerge.net:80)
• Username: Enter the DVR’s user name (by default, admin)
• Password: Enter the DVR’s password (by default, 000000)
3. Tap Done to continue.
Enter DVR name
Enter DVR DDNS address or local IP address
Enter DVR user ID (by default: admin)
Enter DVR password (by default: 000000)
Tap Done
96
You must include the
port number when
entering the DVR’s
DDNS or LAN address.
Digi Imobile Touch - iPhone App
Connecting to your DVR
1. From the Device List, tap the name of your DVR to connect.
Tap the name of your DVR
Digi iMobile Touch Lite Interface
Full Screen
Viewing modes
Toggle on screen display (OSD)
Take screenshot*
PTZ
* Screenshots are stored in your iPhone’s photo album.
97
Digi Imobile Touch - iPhone App
Digi iMobile Touch Pro Interface
Full Screen
Search DVR
Take screenshot*
Viewing modes
PTZ
Toggle on screen
display (OSD)
Opens Device
Control menu
* Screenshots are stored in your iPhone’s photo album.
About the Search and Control menus
The Search and Control menus are exclusive to Digi iMobile Touch Pro. The search menu allows
you to search and playback video on your DVR.
The Control menu allows you to turn recording on or off, enable or disable relay control, and turn
schedule recording on or off.
For details on how to use the Search and Control menu, see “Digi iMobile Touch Pro features” on
page 101.
98
Digi Imobile Touch - iPhone App
Changing Viewing Modes
• Touch
to change viewing modes.
Single channel view
Quad View
Swipe finger to change channels
(single channel view only)
9-channel view
16-channel view
Digi iMobile Touch Lite interface shown
Rotating the Screen
Rotate your iPhone to change the image orientation.
Digi iMobile Touch Lite interface shown
99
Digi Imobile Touch - iPhone App
Toggling the On Screen Display (OSD)
• Tap the OSD button to turn the OSD on/off. The OSD displays the recording status and DVR time.
OSD on
OSD Off
DVR Time
OSD button
Digi iMobile Touch Lite interface shown
PTZ
To control connected PTZ cameras to the DVR:
1. Select the channel that the PTZ camera is connected to in single channel mode.
2. Tap the PTZ button.
3. Tap the arrows to pan/tilt the camera. Tap + and - to zoom in and o ut.
Tap arrows to pan and tilt camera
Tap + / - to zoom in or out
PTZ button
Digi iMobile Touch Lite interface shown
100
Digi Imobile Touch - iPhone App
Digi iMobile Touch Pro features
Search
The Search menu allows you to search for recorded video on your DVR.
To search for video:
1. Tap the Search icon (
).
2. Tap the arrows to select the month, and then tap the desired date to begin the search.
Tap here to select month
Tap here to select date
3. Tap the hour that you wish to begin the search. Next, drag the Min button to search for the
minute that you wish to search.
1. Tap here to select desired hour
2. Drag Minute button to select
desired minute
3. Tap one of the preview
windows to begin playback
4. Tap one of the preview windows to begin playback (see image above).
101
Digi Imobile Touch - iPhone App
5. Use the playback controls to pause, fast forward, or rewind video.
Tap here to view
channel in full screen
view. Tap repeatedly to
change channels in full
screen view.
Playback Controls
Exit playback
Device Control
The Device Control menu allows you to turn recording, scheduled recording and relay alarms on
or off.
To configure the Device menu:
1. Tap the Control button (
).
Tap here to close the Device Control menu.
Tap here to turn dial to the On or Off position.
2. Configure the following:
• Record: Tap the Record button to turn DVR recording on or off.
• Schedule: Tap the Schedule button to stop or start scheduled recording.
• Alarm: Tap the Alarm button to turn alarm devices on or off.
3. Tap X to close the Device Control menu.
102
Digi iMobile Touch Lite - ANDROID
DIGI IMOBILE TOUCH LITE - ANDROID
Digi iMobile Touch Lite is an Android app that allows you to remotely view your DH200 series DVR.
NOTE: Digi iMobile Touch Lite is capable of viewing only.
NOTE: These instructions are based on the HTC Wildfire smartphone. For specific installation
instructions, consult your smartphone’s user’s manual.
Compatible Devices
• Android OS (2.1 and above, touch screen models only)
• Digimerge DH200 Series DVR
Prerequisites
• Port 80 (or whichever port your system is using) must be port forwarded to your router
• You must create a DDNS account, and have the DDNS settings configured in your DVR
• The DVR must have internet access
• You must have a Digimerge DDNS address to log in remotely
• An Android Market account
NOTE: You will need to create an Android Market account to download the app.
Installation Steps
1. Search for DigiiMobile Touch Lite in the Android Market. Follow the on-screen instructions to
install the app.
Search for digiimobile touch lite
Starting Digi iMobile Touch Lite
• Tap on the Digi iMobile Touch Lite icon (
) to start the app.
103
Digi iMobile Touch Lite - ANDROID
Configuring Digi iMobile Touch Lite
Once you have installed the application, enter your DVR‘s information to connect remotely.
To enter your DVR information into Digi iMobile Touch Lite:
1. Press the Menu button on your phone, and then tap Add Device.
You can add a maximum
of two (2) DVRs to the
Device list.
Tap Add Device
2. Enter the following:
• Name: Enter the DVR name of your choice.
• IP/Host:
• Enter the local IP of the DVR, followed by a colon, followed by the DVR’s port number
OR
• Enter the DDNS address of the DVR, followed by a colon, followed by the DVR’s port
number (i.e. touch.digimerge.net:80)
• Username: Enter the DVR’s user name (by default, admin)
• Password: Enter the DVR’s password (by default, 000000)
3. Tap Done to continue.
Enter DVR name
touch.digimerge.net:80
Enter DVR DDNS address or local IP address
Enter DVR user ID (by default: admin)
Enter DVR password (by default: 000000)
You must include the
port number when
entering the DVR’s
DDNS or LAN address.
*Phone interface may vary depending on model.
104
Digi iMobile Touch Lite - ANDROID
Connecting to your DVR
1. From the Device List, tap the name of your DVR to connect.
Tap the name of your DVR
To remove a DVR:
Press and hold the selected DVR, then
tap Delete Device.
Digi iMobile Touch Lite Interface
Viewing modes
Double-tap the
channel you wish to
view on full screen
Take screenshot*
Toggle on screen
display (OSD)
PTZ
* Screenshots are stored in your phone’s photo album
105
Digi iMobile Touch Lite - ANDROID
Changing Viewing Modes
• Touch
to change viewing modes.
Single channel view
Quad View
Live
Live
Tap the single channel button to
change channels
16-channel view
9-channel view
Live
Live
Rotating the Screen
Live
Rotate your phone to change the image orientation.
106
Digi iMobile Touch Lite - ANDROID
Toggling the On Screen Display (OSD)
• Tap the OSD button to turn the OSD on/off. The OSD displays the recording status and DVR time.
DVR Time
OSD on
OSD Off
Live
Live
OSD button
PTZ
To control connected PTZ cameras to the DVR:
1. Select the channel that the PTZ camera is connected to in single channel mode.
2. Tap the PTZ button.
3. Tap the arrows to pan/tilt the camera. Tap + and - to zoom in and o ut.
Live
Tap arrows to pan and tilt camera
Tap + / - to zoom in or out
PTZ button
107
Installing the BDVRViewer App on your Blackberry
INSTALLING THE BDVRVIEWER APP ON YOUR
BLACKBERRY
The BDVRViewer application allows you to remotely view your DH200 Touch series DVR on your
Blackberry.
Prerequisites
• Blackberry 9000 or 9700 only
• An APN name, obtained from your Blackberry
service provider (Digimerge does not provide
this)
• A DDNS account from
https://secure.digimerge.net/webapp/
!
You must port forward your router
before you can connect to your
system using a mobile device
Step 1 of 4: Download the BDVRViewer Application
1. Open the web browser on your Blackberry, and go to http://mobile.digi1.net/java
2. Click on the BlackBerry Test Release link.
BlackBerry Test Release
3. Click the Download button. Click Yes to any download warnings.
4. Click OK to exit.
108
Installing the BDVRViewer App on your Blackberry
Step 2 of 4: Clear your browser cache
You must clear your browser cache for the BDVRViewer application to run properly.
1. Open the web browser on your Blackberry, and then press
2. Click Options.
.
Options
3. Beside Content Cache, click the Clear button.
Clear button
4. Exit the web browser to save your changes.
109
Installing the BDVRViewer App on your Blackberry
Step 3 of 4: Enable APN (Access Point Name)
In order for BDVRViewer to function, you must enable APN (Access Point Name) on your
Blackberry. Contact your service provider for your Blackberry’s APN name.
To enable APN:
1. Press the Menu button (
2. Open the Options menu.
).
Options folder
3. Select Advanced Options > TCP/IP
4. Select the checkbox beside APN Settings to enable APN.
Example
APN address
5. Beside APN, enter your APN address. You must obtain the APN from your local service
provider.
6. Exit to save your settings.
110
Installing the BDVRViewer App on your Blackberry
Step 4 of 4: Log in to BDVRViewer
1. Press the Menu button (
) and then open the Downloads folder.
BDVRViewer
2. Click on the BDVRViewer icon.
3. Enter the DVR DDNS address, port number, ID, and password, and then click LOGIN.
Enter the DVR’s DDNS address (i.e. tomsmith.digimerge.net)
Enter the DVR’s port number (i.e. port 80)
Enter the DVR’s login ID (default: admin)
Enter the DVR’s password (default: 000000)
4. A network security window opens. Click Yes to connect to the DVR.
Viewing Tips
• During viewing, press the Menu button (
) to open the channel options window. Select the
desired channel to view in full screen, or select a group of 4 channels to view in quad mode.
Channel options
Single channel
Quad view
111
Appendix A: System Specifications
APPENDIX A: SYSTEM SPECIFICATIONS
DVR
Description
Specification
Video Input
8/16 x 1.0Vp-p, CVBS, 75ohms, BNC
Video Output
1 composite (BNC)
1 spot output, programmable
1 VGA
Audio Input
1 x line-in (RCA)
Audio Output
1 x line-out (RCA)
Audio
1-way audio conference (via network)
Video Compression
H.264 hardware codec
Audio Compression
G.711
Supply Voltage
100VAC - 240VAC, 12VDC , 3A, 50/60Hz
Power Consumption
Approx. 19.2 watts (HDD 250GB)
Operating Temp.
Range
-32°~104° F / 0° ~ 40° C
Hard Disk Capacity
1 HDD (Max 2TB), 100% duty cycle
Operating System
Linux (embedded)
OSD Navigation
USB mouse, IR controller, or 20 key front panel
Backup
Via USB to flash and optical drives
Backup File Format
Embedded player; convertible to AVI
Recording
Resolution
360 x 240 : 240/200 (NTSC/PAL)
720 x 240 : 120/100 (NTSC/PAL)
720 x 480 : 60/50 (NTSC/PAL)
Image Size
5-30 KB (720x480, 720x576) FPS
3-19 KB (720x240, 720x288) FPS
2-12 KB (360x240, 360x288) FPS
Record Scheduling
Daily, Weekly; adjust specific HR per channel
Pre/Post Alarm
recording
5 seconds (Pre); 5 minutes (Post), programmable per camera
112
Appendix A: System Specifications
DVR (cont’d.)
Description
Specification
Event/Log Search
Unlimited for user login/out, configuration changes, remote access, connects/disconnects
Playback
Single, Quad, 8, 16 CH Simultaneous
Alarm Input
4/8/16 x TTL, programmable as NC/NO
Alarm Output
1 x Relay with NO/NC contact; 24VDC/2A,
240VAC/2A resistive
Activity Detection
Sensitivity levels: 20
PTZ Control
RS-485/RS-422 Interface
Mobile Viewing
3G Smart Phone viewing, supports BlackBerry,
iPhone & Android (check website for compatibility listing)
Front Key
Max 20 (Touch Sensor)
Front LED
Power, REC, HDD
Unit Weight
1.91 kg/4.2 Lbs
Remote Functions
Live View, Live Recording, Search, Set-up, Backup
Network Speed
Control
8 levels (64KB ~ 8MB)/sec.
Network Protocol
TCP/IP, DDNS and Web
Network Interface
10/100-Base-TX, RJ-45
Dimensions
As our products are subject to continuous improvement, Digimerge Technology Inc. and its
subsidiaries reserve the right to modify product design, specifications, and prices without notice
and without incurring any obligation. E&OE
113
Appendix B: Setting up Remote Viewing
APPENDIX B: SETTING UP REMOTE VIEWING
Setting up the Remote Viewing Feature requires several steps. Networking skills are required to
correctly configure the remote viewing functions.
What Do I Need?
• DVR System
• A PC with the installed CMS-DH software
• A router (not provided with the system) and High Speed Cable or DSL Internet Connectivity
(for remote viewing outside your network)
DVR*
INTERNET
ROUTER
(Not Included)
PC
(Not Included)
*8-channel model shown.
Network Setup / Remote Access Overview
To setup remote viewing:
1. With the system powered off, connect the system to the router using an Ethernet cable.
2. Power the system on. You must connect the system to the router prior to turning on the
system. This allows the system and router to communicate over the network.
3. Press and hold the Enter button on the front panel to find your system's IP address.
4. Enable Port Forwarding on your router. Refer to the included Router Guide and Basics of
Remote Video Access Guide for further assistance with your specific network setup and
hardware.
5. Setup an account at http://ddns.digimerge.net
114
Appendix B: Setting up Remote Viewing
How Do I Find My IP and MAC addresses?
The IP and MAC address of your system are necessary for DDNS setup. DDNS allows you to view
and control your system from a remote location.
Figure 40.0 DVR Status screen
To find your IP and MAC addresses:
1. Open the MAIN MENU and select SYSTEM.
2. Under the INFO tab you will find your system’s IP address and MAC address.
Finding Your External IP Address
If you wish to find your external IP address, you can use a third-party website such as
www.showmyip.com
Your external IP address can also be found within your Router settings. Refer to your router user
guide for further details.
115
Appendix B: Setting up Remote Viewing
How Do I Enable Port Forwarding?
You need to enable port forwarding on your router to allow for external communications with your
system for the following port:
• 80
Computers, DVRs, and other devices inside your network can only communicate directly with each
other within the internal network. Computers and systems outside your network cannot directly
communicate with these devices. When a system on the internal network needs to send or receive
information from a system outside the network (i.e. from the Internet), the information is sent to
the router.
NETWORK EXAMPLE
Router
External IP
216.13.154.34
Router
Internal IP
192.168.0.1
PC
Internal IP
192.168.0.2
DVR
Internal IP
192.168.0.3
Internet
Internal Network
When a computer on the Internet needs to send data to your internal network, it sends this data
to the external IP address of the Router. The Router then needs to decide where this data is to be
sent to. This is where setting up Port Forwarding becomes important.
Port Forwarding tells the router which device on the internal network to send the data to. When
you set up port forwarding on your Router, it takes the data from the external IP address:port
number and sends that data to an internal IP address:port number (i.e. Router External IP
216.13.154.34 to DVR Internal IP 192.168.0.3:80).
The instructions found online in the Router Configuration Guides will assist you in the port
forwarding configurations for a selection of different router models. Visit our Consumer Guides
Support website at http://www.digimerge.com/ for more details.
The Digimerge Auto Port Forwarding Wizard is an exclusive software that easily automates router
port forwarding. Before setting up a DDNS account, it is recommended to run the Auto Port
Forwarding Wizard to port forward the required ports.
116
Appendix C: Digimerge Auto Port Forwarding Wizard
APPENDIX C: DIGIMERGE AUTO PORT FORWARDING WIZARD
Installation
To install the Digimerge Auto Port Forwarding Wizard:
1. Insert the system’s software CD, and follow the instructions to launch the Digimerge Auto
Port Forwarding Wizard software.
• The installation window opens.
2. Click Next to continue.
Select
installation
directory
(optional)
Click Next
3. Click the Change button to change the default installation directory (optional). Click the Next
button to continue.
4. Select the users who can see the Auto Port Forwarding shortcut (Optional). Click the Next
button to continue.
Select the users who can see the software shortcut (optional)
117
Appendix C: Digimerge Auto Port Forwarding Wizard
5. Click the Next button and then click Finish to complete the software installation.
Finish button
6. Double-click the Digimerge Auto Port Forwarding shortcut (
the program.
)from your desktop to start
Obtaining Your Router Model Number and Version
On most routers, the model and version number can be found underneath the router, printed on
a sticker.
Example
• WGR614 refers to the model number
• v9 refers to the version number
118
Appendix C: Digimerge Auto Port Forwarding Wizard
Configuration
You must have the following before you configure the software:
1. Your router’s model number and version number
2. Your router’s user name and password
3. Your Digimerge device’s IP address
4. Your Digimerge device’s port numbers that require port
forwarding
Initial Startup: Select language
1. Click the Language drop-down menu and select a language (English, French, Spanish). Click
the Start button to continue.
Software update section
Start button
Language drop-down menu
Download Now button
A software update includes an updated list of routers
compatible with the Auto Port forwarding Wizard.
2. If software updates are available, click the Download Now button in the top-right corner.
• Run the update file and install the latest version of the software.
Step 1: Populate the router database
The Auto Port Forwarding Wizard automatically populates a list of current routers, and detects
the number of connected routers.
1. Click the Next button after the software detects your router configuration.
Click to update router database
Click to check for multiple routers
If more than one router is detected, you
may need to contact your ISP (Internet
Service Provider) to port forward.
For details on configuring multiple
routers, see “Configuring multiple
routers” on page 121.
119
Appendix C: Digimerge Auto Port Forwarding Wizard
Step 2: Enter your router settings
1. Under the Router drop-down list, select the model of your router.
OR
• Click the Search button (
) to enter the name of your router model.
NOTE: Click the Auto Detect button (
most Linksys or Netgear models).
)if you have a Linksys or Netgear router (works with
Search and Auto detect
button
Router drop-down list
Enable Silent Mode
Router IP
Router user name &
password
Enter port 80 under
Ports
).
2. Under Router IP, click the Detect Router IP button (
• The router’s IP populates in the blank field. Click OK to exit the prompt.
3. Under Username and Password, enter the router’s username and password.
• Optional: Under HTTP Type (default http://) and HTTP Port (default, 80), you may have to
change the values depending on your router model. Consult your router manual for details.
Enter your Digimerge
device’s IP
Enter port
number
4. Under IP, enter the IP address of your Digimerge device.
NOTE: The IP is usually found in the information window of your DVR.
5. Under Port, enter the DVR’s Web Port (by default, port 80).
6. Click Next to continue.
120
Appendix C: Digimerge Auto Port Forwarding Wizard
Step 3: Update the router settings
1. Click the Update Router button.
• You will see your router window open. The Auto Port Forwarding Wizard automatically
populates your router with the relevant information. This will take a few moments.
Update Router button
2. Close the update window when the update finishes.
Step 4: Test your connection
1. Click the Test Your Connection button.
• Your system’s default browser opens and connects to your Digimerge device.
NOTE: Ensure that Internet Explorer is your system’s default internet browser.
NOTE: A window opens that prompts you to enter in your DVR’s user name and password (do
not enter your DDNS log in information).
NOTE: ActiveX warnings may appear. Accept all ActiveX installation warnings to connect to your
system. For details.
Configuring multiple routers
Your network may have two or more connected routers. During the initial launch of the auto port
forwarding wizard, the program scans the network to detect the number of connected routers.
To check for multiple routers:
).
1. Click the Detect Multiple Routers button (
• A list of connected router populates in the window.
121
Appendix C: Digimerge Auto Port Forwarding Wizard
• The "Possible 1st Router" refers to the router directly connected to your system. This is the
router that requires the port forward information.
• The "Possible 2nd Router" refers to the router immediate to the internet connection. This is
the router that requires you to configure a DMZ host connection.
Scenario A: Router/Modem combination + Router
• You may have a router/modem combination, with a second router in your network.
Scearnio B: Multiple Routers
• You may have two routers in your network.
Internet
DMZ IP
Port Forward port 80 &
554 to Router 1
Computer
Modem
Router 2
Router 1
DVR System
EXAMPLE
Enter 192.168.1.100 into the DMZ
Host IP section into Router 2
IP Address: 192.168.1.100
(Assigned by Router 2)
In both scenarios, the router that is immediate to the internet connection (Router 2 in illustration)
must act as a "bridge" to another router (Router 1 in illustration). The Auto Port Forwarding
Wizard must connect to Router 1.
A proper DMZ configuration in Router 2 allows all incoming traffic going through Router 2 to
automatically pass to Router 1. Router 2 acts as a "dummy" router and passes all the incoming
data onto Router 1. Router 1 is the router that needs the port forwarding information.
122
Appendix C: Digimerge Auto Port Forwarding Wizard
Configuring a DMZ host connection
• Connect to "Router 1" on your network (referred
to as "Possible 1st Router" in the Auto Port
Forwarding Wizard). Obtain the IP address of
Router 1. Usually this can be found in the
"Status" section of your router menu. The IP
should begin with "192.168...."This IP address is
your DMZ IP.
Example
DMZ stands for Demilitarized Zone. Enabling a DMZ
IP on your router enables one of the routers to pass
information onto the second router.
DMZ IP address
assigned by a
secondary router
• Enter the IP address obtained from Router 1 into
the DMZ section of Router 2.
• Once you have configured Router 2 with a DMZ
connection, run the Auto Port Forwarding
Wizard to begin auto port forwarding to Router 1.
• Consult your router’s owner’s manual for details
on configuring DMZ settings.
Locating your Router IP - The Status Page
The "Status Page" of a router normally includes the router’s
vital information such as the IP address.
EXAMPLE
The IP information is
normally under a
header called "WAN" or
"Internet Port". Each
router has different
terminology.
Router IP assigned by
the main router. Enter
this IP into the DMZ
section of the primary
router.
123
Appendix D: Setting Up DDNS Service
APPENDIX D: SETTING UP DDNS SERVICE
Digimerge offers a free DDNS service for use with your DVR. A DDNS account allows you to set up
a web site address that points back to your local network. The following outlines how to set up
your free DDNS account.
To setup your free Digimerge DDNS account:
1. In your browser, go to http://
ddns.digimerge.net and click Create Account.
2. Complete the Account Information fields with
your personal information. Complete the
Warranty Information with your purchase
details (optional).
3. Complete the System Information fields:
• Product License: Select your product model
from the Product License drop down menu
(e.g. VB300)
Figure 41.0 Create a DDNS account
• <Product Code> - <MAC Address>:
Locate the MAC address of your (recorded
while loading the System)
• URL Request: Choose a URL for your DDNS
connection (i.e. your name, your company or
business name, or anything of your choice.)
4. Once the information has been entered, click
Create New Account.
5. Your Account information will be sent to you at
the email Address you used in Step 2.
Figure 41.2 System information
124
Figure 41.1 Enter personal information
Appendix D: Setting Up DDNS Service
You will need this information for remote access to your system. Record your information below:
Username:
Domain name*:
Password:
* Only the first part of the Domain Name is required for setup on the system. For
example, if the full domain name is tomsmith.digimerge.net, you only need to enter
tomsmith on the system.
125
Appendix D: Setting Up DDNS Service
How Do I Enable DDNS On My System?
Once you have registered for free DDNS service, use the information in the confirmation email to
configure DDNS settings on your system.
Figure 41.3 DDNS menu
To enable DDNS on your system:
1.
2.
3.
4.
Open the MAIN MENU and click NETWORK.
Select the DDNS tab.
Under USE, select DIGIMERGE.
Under DOMAIN NAME, enter only the first portion of your DDNS domain from the
confirmation email.
For Example:
If your domain name is http://tomsmith.digimerge.net,
you only need to enter tomsmith in the text field.
5. Under USER ID, enter your Digimerge DDNS user name.
6. Under PASSWORD, enter your Digimerge DDNS password.
NOTE: Obtain your Digimerge DDNS user name and password from the confirmation email.
7. Under DDNS TEST, select START. You should receive a "SUCCESS" message. If there is an
error, check your network connections; check that you have entered the correct domain
name, user ID, and password.
8. Press ENTER to save your settings. Press CANCEL/ESC to close remaining windows.
With DDNS entered on your system, you can access your DVR from a remote location by using the
CMS-DH remote software or by entering the Digimerge DDNS domain name in your browser.
126
Appendix E: Setting Up Mobile Access
APPENDIX E: SETTING UP MOBILE ACCESS
This guide shows you how to view video streams from your DVR remotely using your iPhone® or
Blackberry® .
Before You Begin
You must complete these two steps before starting:
1. Register your DVR with the Digimerge DDNS service.
See “Appendix D: Setting Up DDNS Service” on page 124.
2. Enable DDNS on your DVR.
See “How Do I Enable DDNS On My System?” on page 126.
Registering your DH200 for Mobile Access
Before you can log in to your DH200 with a mobile device, you must create a mobile account.
To create a mobile account:
1. Go to http://mobile.digi1.net/ on your web browser and click Register (Figure 41.4).
Registration screen. Click Register to begin registration.
127
Appendix E: Setting Up Mobile Access
Registering your DVR for Mobile Access Cont’d
2. The sign up screen opens.
Enter your desired user ID and password and click Register.
NOTE: Your password must be at least six characters long.
Sign up screen. Enter in desired user ID and password.
3. The DVR registration window opens. Click ADD DVR.
DVR management window. Click ADD DVR to add your DVR.
128
Appendix E: Setting Up Mobile Access
Registering your DVR for Mobile Access Cont’d
4. The EDIT DVR INFORMATION window opens.
DVR registration window. Enter DVR name and DDNS domain name.
5. Enter any desired DVR name (the default name is "DVR"). Enter your DDNS domain name.
NOTE: You do not have to enter the entire DDNS address under DOMAIN NAME.
For example, if your registered DDNS name is myoffice.digimerge.net, you would enter: myoffice
in the DOMAIN NAME field (Figure 41.8.)
Enter your DVR domain name into the DOMAIN NAME field.
129
Appendix E: Setting Up Mobile Access
Registering your DVR for Mobile Access Cont’d
6. Enter your DVR’s user name and password. Click the Apply button.
NOTE: If you change the password of the DVR, you must update your account with the latest
password.
Once you have entered in all the fields, click APPLY to continue.
7. A new window opens that shows: DVR (the name of your dvr), ADD DVR, LOG OUT, SIGN UP.
Click on DVR (the name of your dvr).
8. The DVR camera list opens (Figure 41.10.) Click the desired camera to start viewing video
feed.
Click on desired camera name to begin video feed.
9. Congratulations! Your DVR is registered and ready for mobile access.
Viewing Video from your Mobile Device
Once you have completed the registration steps, enter http://mobile.digi1.net/ on your iPhone or
Blackberry browser. Enter in your user name and password created in step 2 to log in.
Once you are logged in, select the DVR you wish to view, and click on the desired camera to begin
viewing live video.
To view other cameras, click the Back button to view the list of connected cameras.
130
Appendix F: Connecting PTZ Cameras
APPENDIX F: CONNECTING PTZ CAMERAS
You can connect RS-422/485 PTZ cameras (not included) to the PTZ Control Block on the rear
panel of the system.
DVR*
PTZ CAMERA
(not included)
Figure 42.0 Connecting a PTZ camera (not included)
To install a PTZ Camera:
1.
2.
3.
4.
5.
6.
Connect the Transmit Cable to the RS-422/485 TX (+) port of the PTZ block on the rear panel.
Connect the Receive Cable to the RS-422/485 TX (-) port of the PTZ block on the rear panel.
Connect the video cable to a BNC port (usually channel 1).
Open the Main Menu and select CAMERA.
Under PTZ MODEL, select the model of your PTZ camera.
Under PTZ ID, select the PTZ ID (PTZ ID should match the camera channel to which you have
connected the PTZ camera).
NOTE: The PTZ camera settings depend on the type of PTZ camera. Please refer to the specific camera
manual for your brand and model of PTZ camera.
7. Press the ENTER button to save your settings.
*8-channel model shown.
131
Appendix F: Connecting PTZ Cameras
Using a PTZ Camera
To control a PTZ camera:
1. With your PTZ connected to the system, view the active PTZ channel
in full-screen.
2. Press PTZ button on the front panel, remote control, or Virtual
Remote (mouse only). The Short-cut Menu opens.
3. Press any of the buttons on the Short-Cut menu to open the PTZ
Help Menu.
Figure 42.1 PTZ Short-cut menu
The PTZ Help Menu contains the following:
Button
ENTER button
Result/Action
• Press to open the PTZ Help Menu; press again to close the
menu
ESC button
• Press to cancel all PTZ operation
MENU button
• Press to open the PTZ Virtual Remote; press
again to return to the Short-cut menu
Navigation buttons
• Press ST to tilt up/down
• Press WX to pan left/right
132
Appendix F: Connecting PTZ Cameras
Increase/Decrease
buttons
Button
• Press + / - to zoom in and out
Result/Action
• Set PRESET position; Spot Out on the remote control
• Move PTZ to a desired location
• Press the preset button
• Illuminate Custom 1
• Set the # for the Preset location
• Press ENTER to save and exit
• Go to the preset position; INFO on the remote control
• Press the GO button
• Enter the desired Preset # and press ENTER
• Start AUTO TOUR
• Press the Auto Tour button
• Press + and enter the range of preset and press ENTER
• For example, Auto Tour button, +5 will start the tour of 1~5
presets of the PTZ camera
• PTZ custom function 1; Display on the remote control
• PTZ custom function 2; Zoom on the remote control
• PTZ custom function 3; PTZ on the remote control
• Speed has 8 increments—keep pressing the buttons to
increase/decrease speed
133
Appendix F: Connecting PTZ Cameras
Compatible PTZ Cameras
NOTE: The default baude rate is 9600, unless otherwise stated in the system’s Camera menu
134
Appendix G: Connecting Additional External Monitors
APPENDIX G: CONNECTING ADDITIONAL
EXTERNAL MONITORS
Use the Video port (BNC) on the rear panel of the system to use the Monitor Out function. Monitor
Out displays the exact on-screen display of the system.
Use the Spot port (BNC) to use the Spot Out function. Spot Out displays connected cameras on the
system.
NOTE: A BNC-to-RCA adapter (not included) is required to connect a monitor with RCA inputs.
Monitor
(not included)
DVR*
Spot Monitor
(not included)
*8-channel model shown.
To use spot out functions:
1. With a spot monitor connected, press the SPOT OUT button on
the remote control or Virtual Remote followed by the numeric
button for the channel you wish to view (full-screen).
2. Press the SPOT OUT button twice to begin Auto Sequence (by
default, Spot Out on the system is set to Auto Sequence).
When an alarm is triggered, Spot Out will display the triggered
channel in full-screen.
Spot Out button
135
Appendix H: Connecting Motion / Alarm Devices
APPENDIX H: CONNECTING MOTION / ALARM DEVICES
You can enable motion detection and alarm control from the Main Menu. You can also connect
additional motion sensor devices to the system (i.e. motion sensors, door/window sensors). Use
a motion detector or sensor to send a signal to the system to begin camera viewing and recording
on the matching camera channel (when enabled in the Menu).
To connect an external alarm sensor (ALARM INPUT) to the system:
1.
2.
3.
4.
5.
Connect the Signal Cable to the desired Channel number + port in the alarm block.
Connect the Ground cable to the Ground port (G) in the alarm block.
Open the MAIN MENU and select ALARM.
Select the corresponding alarm channel and select INPUT.
Select N.C. (Normally closed) or N.O. (normally open) depending on your alarm/sensor setup.
Make sure the channel is set to ON.
6. Press the ENTER button to save your settings.
DVR*
ALARM or SENSOR
(Not Included)
*8-channel model shown.
136
Appendix H: Connecting Motion / Alarm Devices
Connecting an Alarm OUT device
After you have connected an Alarm IN device (i.e. alarm or sensor), you must connect an alarm
OUT device (i.e. strobe light etc. (not included)).
To connect a device to the Alarm Out port in the alarm block:
1. Connect the wires on the device to 1A and 1B of the alarm output. 1A is positive (+); 1B is
negative (-).
1A (+)
1B (-)
8 Channel
1A (+)
1B (-)
16 Channel
Enabling the connected Ouput device in the Alarm menu
To enable the output device in the Alarm menu:
1. Open the main menu>ALARM>ALARM SETUP
2. Beside Alarm Out1, select the desired trigger type by clicking + and - .
on the upper right corner of the
Beside the ON/OFF box, select ON and then click
screen to save your settings.
137
Appendix I: Full Connectivity Diagram
APPENDIX I: FULL CONNECTIVITY DIAGRAM
The following diagram outlines a general set of connections available with the DVR.
SELF-POWERED
MICROPHONE
EXTERNAL
MONITOR
(Not Included)
(Not Included)
AUDIO CAPABLE
CAMERA
(Not Included)
MOUSE
VGA MONITOR
BNC CAMERAS*
(Not Included)
USB or PS/2
(with adapter)
(Not Included)
(Not Included)
DVR†
POWER
SPOT
MONITOR
PTZ CAMERA
(Not Included)
(Not Included)
LINE OUT/AMPLIFIED
SPEAKERS
(Not Included)
(Not Included)
PC
(Not Included)
*Number of cameras varies by model.
†8-channel model shown.
138
Appendix J: Replacing the Hard Drive
APPENDIX J: REPLACING THE HARD DRIVE
The system comes with a pre-installed 3.5" SATA hard drive. The system supports up to 2
terabytes (TB) of SATA storage—one 2TB 3.5" SATA HDD.
NOTE: Make sure that the system is OFF and the power cable has been disconnected before
changing the hard drive.
Removing the Hard Drive
To remove the hard drive:
1. Remove the four short screws on the side panels of the housing and the eight screws on the
rear panel. Keep these sets of screws separate.
NOTE: The center screw at the top of the rear panel and the screws along the audio and video ports are
longer than the other screws.
ATTENTION: Do not remove the two screws near the fan on the side of the housing.
2. Carefully slide the cover away from the front panel and lift away from the housing.
NOTE: Make sure the cover is clear of all ports and connectors on the rear panel.
Slide the cover and lift away from housing
3. Disconnect the cables from the hard drive.
4. With one hand supporting the hard drive, remove the four mounting screws from underneath
the housing.
Support the HDD and remove the mounting screws underneath the housing
5. Remove the hard drive from the housing.
139
Appendix J: Replacing the Hard Drive
Replacing the Hard Drive
To replace the hard disk:
1. Carefully position the new hard drive on the four rubber mounting feet in the housing. The
connections end of the hard drive should face the data and power cables.
Figure 44.2 Place the HDD on the rubber mounting feet
2. With your hand supporting the hard drive, replace the four mounting screws underneath the
housing.
3. Reconnect the cables to the hard disk. Make
sure the cables are connected firmly.
4. Carefully replace the cover over the housing
and slide towards the front panel. The cover
should be flush on all sides.
5. Replace the screws on the rear panel: 3 short
screws at the corners, 1 longer screws at the
top, and 4 longer screws along the video ports.
6. Replace the short screws on the side panels.
7. Reconnect all cameras and cables. Re-mount
the unit the back of your monitor if desired.
8. Power on the system. If you have installed a
new hard disk, you must format the hard disk
before using the system.
Figure 44.3 Reconnect the power and data cables
140
Appendix J: Replacing the Hard Drive
Formatting the Hard Drive
ATTENTION: Formatting the HDD erases all data on the hard disk. This step cannot
be undone. System settings will not be erased.
Figure 44.4 HDD format
To format the hard disk:
1. Under the DISK tab, select FORMAT and select INTERNAL HDD.
2. Under ACTION, select START. Formatting begins.
3. When formatting is complete, press CANCEL/ESC to close windows (USB flash drive only).
141
Appendix K: Using Listen-in Audio
APPENDIX K: USING LISTEN-IN AUDIO
Listen-in audio allows you to listen to, and record live audio on the system.
DVR*
AUDIO CAPABLE CAMERAS
(not included)
LINE OUT / AMPLIFIED SPEAKERS
(not included)
*8-channel model shown.
To enable listen-in audio:
1. Connect the audio cable (RCA) from an audio capable camera (not included) to the AUDIO IN
port on the rear panel of the system.
2. Open the MAIN MENU and select DEVICE.
3. Beside AUDIO RECORD, select ON.
NOTE: The number of audio inputs varies by model.
4. Press the ENTER button to save your settings.
142
Appendix L: Converting Video Files to AVI
APPENDIX L: CONVERTING VIDEO FILES TO AVI
The system saves recorded video data in the .cms format. When you backup video to a USB flash
drive, external HDD, or CD/DVD-R/W disc, the system also copies the small AVI Converter
application.
NOTE: AVI Converter is also installed on your PC when you install the CMS-DH remote client software.
AVI Converter allows you convert CMS files into AVI format for flexibility when playing back the
video in third-party media players, such as VLC and DivX Player. Converting the file to AVI can be
particularly useful if you need to provide authorities with copies of your video data if there is a
security incident at your business or home.
NOTE: The DivX, XviD, or ffdshow codec (not included) is required to view AVIs in Windows Media Player.
To convert video files to AVI:
1. Connect a USB flash drive or external HDD with backed up video to your PC; or insert a CD/
DVD-R/W disc into your PC’s CD/DVD-RW drive.
2. View files and folders on the drive or disc and double-click aviconverter.exe.
NOTE: If you have already installed CMS-DH, select Start>Programs>CMS-DH>AVI Converter.
3. Under Input File, click
.
4. In the dialogue window, select your saved CMS file and click Open. By default, AVI Converter
will save the converted file to the same location as the Input file. To keep the default, go to
step 6. To choose a new location, go to step 5.
5. Under Output File, click
to choose a save location or personalize the file name.
6. Under Channel, select the channel you wish to save.
NOTE: You can only convert video from one channel at a time.
7. Under Video Standard, select NTSC (default) or PAL. Select the box below Video Standard to
open the file once conversion is finished (default).
8. Click CONVERT. Conversion may take several moments depending on the size of the file.
143
Appendix L: Converting Video Files to AVI
Playing AVI Files
If you selected for the converted file to open automatically, the file will open in your default media
player. If not, click QUIT to close AVI Converter.
ATTENTION: An AVI media player such as VLC or DivX is required to playback AVI files. You
can also installed the XviD, DivX, or ffdshow codecs to play the AVI files in Windows Media
Player.
To playback AVI files:
1. On your PC, open the folder where you saved the AVI file. By default, converted files use the
following naming convention:
yyyy_mm_dd_hh_mm_ss_channel#_channel#_channel#_channel#.avi
2. Double-click the file to open in your default media player, or right-click to open the file with a
AVI-compatible media player.
File playback in Windows Media Player (image simulated)
144
Appendix M: Remote Viewing using Internet Explorer
APPENDIX M: REMOTE VIEWING USING
INTERNET EXPLORER
Along with the CMS-DH remote client software, you can also view your system remotely using
Internet Explorer (version 7 or later recommended). Remote viewing through Internet Explorer
allows for viewing from up to three simultaneous connections.
NOTE: Remote viewing is only compatible with Internet Explorer.
Mozilla Firefox, Opera, Safari and other browsers are not supported.
To view your system using Internet Explorer:
1. Open Internet Explorer.
2. In the address bar, enter your system’s IP address or your
Digimerge DDNS domain followed by :80 — for example,
http://192.168.1.1:80 or
http://tomsmith.digimerge.net:80
NOTE: You MUST include http:// in order to access your system.
NOTE: If you need help finding your system’s IP address, see “How
Do I Find My IP and MAC addresses?” on page 115.
3. Login with the user name admin, and your default system
password, 000000.
4. From the new page, click Web Viewer (Use overlay). You
will need to install ActiveX in order to access live viewing.
5. Click the warning bar and select Install ActiveX Control.
6. From the prompt, click Install. The page will refresh and
live viewing will commence.
Login (admin/000000)
http://192.168.1.1:80
Click Web Viewer (Use Overlay)
Install ActiveX
Click Install
Remote viewing through Internet Explorer (images simulated)
145
Appendix M: Remote Viewing using Internet Explorer
Using Live Viewer
Remote viewing through Internet Explorer (images simulated)
To view full screen:
• Click the buttons at the top of the page or double-click a channel. Double-click the channel
again to return to split-screen.
To view split-screen:
• Click the 4, 9, or 16 buttons at the top of the page.
NOTE: The number of displayed channels depends on the number of channels available on your DVR.
DVR channels vary by model (8-channel model shown).
DVR Webserver
To configure your DVR system settings, PTZ settings etc. using Internet explorer, you can log in to
the system using the webserver command. To log in as a webserver user, enter /webserver at the
end of your DDNS address. For example, if your DDNS address is tomsmith.digimerge.net:80, you
would enter tomsmith.digimerge.net:80/webserver.
You will be prompted to install ActiveX components. Allow all installations to continue, and restart
Internet Explorer.
146
Troubleshooting
TROUBLESHOOTING
When a malfunction occurs, it may not be serious and can be corrected easily. The following
describes the most common problems and solutions. Please refer to the following before calling
Digimerge Technical Support:
Error
Possible Causes
Solutions
• DVR is not receiving
power, or is not
powering up
• Cable from power adapter is
loose or is unplugged
• Confirm that all cables are connected correctly
• Cables are connected, but DVR
unit is not receiving sufficient
power
• Confirm that the unit is powered on (LED
indicators on the front should be ON)
• Confirm that the power adapter is securely
connected to the back of the unit
• If the unit is connected through a power bar or
surge protector, try bypassing the bar and
connecting the power directly to the wall outlet
• Confirm that there is power at the outlet:
• Connecting the power cable to another outlet
• Test the outlet with another plugged device
(such as an electric calculator or phone
charger)
• Remote control is
not detected by the
system
• Hard drive is not
detected by the
system
Hard drive is full (0%)
and the unit is no
longer recording
• Batteries in the remote control
are drained
• Install a fresh CR2025 battery in the remote
control
• There are no batteries in the
remote control
• Hard drive cables are loose or
not properly connected
• Remove the housing and check that hard drive
cables are firmly connected
• Hard drive has not been
initialized (formatted) by the
system
• From the Main Menu, select
System>Disk>Format and select Internal and then
click Start. ATTENTION: Formatting erases all
video data on the hard drive
• There is no hard drive in the
system
• Open the housing and install a 3.5" SATA hard
drive
• Repeat Record is not enabled
• From the Main Menu, select
System>Disk>Overwrite and select ON. This
enables the system to continuously record by
overwriting data once the hard drive is full
147
Troubleshooting
Troubleshooting (cont’d.)
Error
Possible Causes
Solutions
Mouse not detected
by system
• Mouse cable is not firmly
connected to the system
• Firmly connect the mouse cable to the PS/2 port
on the side of the system; or connect a USB mouse
to the top USB port on the rear panel of the system
• Mouse is not connected to the
system
• There is no picture
on selected channels
/ camera picture is
not being displayed
• System needs to be reset
• Turn the system OFF (press Power button on the
front panel). Firmly connect a PS/2 mouse to the
PS/2 port on the side of the system; or connect a
USB mouse to the top USB port on the rear panel of
the system. Press the Power button again to turn
the system ON
• Camera cables are loose or
have become disconnected
• Check the camera video cable and connections
• Disconnect and reconnect the cable at the DVR
and at the Camera
• Try moving the camera to another channel or use
another cable
• The image on the
DVR appears, but
does not have sound
• Audio cables are loose or have
been disconnected
• Check the AUDIO connections to the DVR
• Audio channel is set to OFF in
the system menu
• Open Main Menu>Record and set channel 1 audio
to ON
• Audio is associated with the
wrong video channel
• Audio is only available for channel 1—connect the
audio capable camera to channel 1 to avoid
confusion
• I can’t set the time
on the DVR
• The system is recording
• Stop all recording on the system before
attempting to set the time—resume recording
immediately after setting the time
• Schedule recording
isn’t working
• Schedule recording has not
been enabled
/ on the front panel or Virtual
• Press
Remote to enable schedule recording
• A recording schedule has not
been entered
• Open Main Menu>Schedule. Configure up to four
recording Modes. Under the Chart tab, apply the
Modes to ALL days, or specific days
/ on the front panel or Virtual
• Press
Remote to enable schedule recording
148
Troubleshooting
• My system does not
seem to be recording
• Continuous recording may be
disabled
• Press /
on the front panel, or
on the
remote control or Virtual Remote—ATTENTION:
For security, it is highly recommended to keep
continuous recording ON at all times
• Cameras may be disabled
• Open Main Menu>Record. Make sure cameras
are ON
• Motion detection is enabled
• Motion detection means the camera will only
record when motion is detected. Open Main
Menu>Record to enable/disable motion detection
on specific cameras
Remote Connectivity Trouble Shooting
Error
Possible Causes
Solutions
• I cannot connect to
the system using a
DDNS URL
• No internet connection
• Ensure the DVR is connected to a high speed
internet connection.
• A DDNS account was not
created
• Incorrect DDNS URL
• DDNS not enabled on the
system
• Ensure that you have created a DDNS account.
• Ensure that you type the URL in full
ie: http://tomsmith.digimerge.net:80.
• Ensure there are no spelling errors in the
URL.
• Include http:// and the port number of your
system in the URL.
• Ensure DDNS is enabled on your system.
• I receive an error
when I try to log in to
the system
• Incorrect user name and
password
• The default user name is: admin
• The default password is: 000000
• Ensure that caps lock is disabled. The password
and user name are case sensitive.
149
Troubleshooting
150
Right for Business
Need Help?
Please make sure to visit our website www.digimerge.com
to receive product updates and information.
3 Easy Ways To Contact Us
Online:
Product support is available 24/7 including
product information, user manuals, quick start
up guides and FAQ ’s at w w w.digimerge.com
By Email:
Technical support (for technical/installation issues)
tech@digimerge.com
By Phone:
North America: 1-866-816-5919
Technical support (for technical/installation issues)
Mon-Fri 8.00 am to 8.00pm EST
We welcome your feedback at
info@digimerge.com
For more information, visit
www.digimerge.com
05052011_R4
www.digimerge.com
Digimerge Digital Video Recorder (DVR) – 5/3/1 Year Limited Hardware Warranty
Warranty: Subject to the exclusions, limitations and exceptions, Digimerge warrants to the initial end-user purchaser that this
hardware product is free from manufacturing defects in material and workmanship under normal use for a period of three (3)
years from the documented date of purchase. Digimerge warrants the security certified Seagate SV35 Series Hard Disc Drive
(HDD) for a period of (5) years from the documented date of purchase.
DVR Warranty Details:
The three (3) year warranty period consists of:

One (1) year over-the-counter replacement warranty covering parts and labor

Two (2) additional years of repair depot warranty covering parts and labor with proof of RA issued by Digimerge tech
support
Exceptions to the above warranty are:

DVR components including, but not limited to, moving parts, motors, fans, removable flash memory. These are
warranted for a one (1) year period.

Data loss – end users are recommended to back up the content of the hard drive on a regular basis.

Data recovery, consequential damages, incidental damages and costs related to removal and installation of the hard
drive are not covered under this warranty and are not part of the repair or exchange process.
Software & Consumables: All software, accompanying documentation and consumables (including but not limited to fuses and
batteries) provided with or as part of the product are furnished AS IS, and are excluded from warranty coverage. Digimerge is
not obligated to provide the end-user with a substitute product during the warranty period or at any time.
NOTE: Products are subject to continuous improvement. DIGIMERGE Technologies Inc. and its subsidiaries reserve the right
to modify product design, specifications and prices, without notice and without incurring any obligation. Software and firmware
are subject to updates from time to time.
For valid warranty claims made during the warranty period, upon proper proof of purchase (which is defined as a “valid form
of a bill of sale or receipt from an authorized retailer or distributor showing the original date of purchase”), defective products
will, at the sole discretion of Digimerge, be repaired or replaced with equal or better product in terms of hardware features
without charge if all the conditions set forth in this warranty are met. Any products repaired or replaced within the warranty
period, shall be warranted by Digimerge to the initial end-user purchaser for 90 days from the return shipment date, or the
remainder of the warranty term, whichever is longer. Repairs are warranted for 90 days outside the original warranty period.
Products and parts, at Digimerge’s sole discretion, may be replaced with new or refurbished items, and the products and parts
replaced become the property of Digimerge. Product returned to Digimerge must be properly packaged in its original
packaging (or packaging providing the product with protection equivalent to the original packaging) and sent, with the postage
charges prepaid via a shipping method that provides for tracking of your package, to the address provided at the time the
Return Authorization was requested. The customer is responsible for all shipping costs associated with the return of the
defective products for warranty service to Digimerge warranty/repair depot facilities. Products will be returned to the end-user
freight prepaid. Digimerge reserves the right to replace the original hard drive with an equivalent one.
Exclusions and Limitations: Any of the following will void this warranty:
1. Installation or use of the product other than strictly in accordance with the instructions contained in the product’s
instruction manual;
2. If the product is subjected to operating conditions (including atmospheric, moisture and humidity conditions) outside
of the acceptable conditions specified in the product's instruction manual;
3. If the product is subjected to misuse (not adhering to instructions supplied with the product), negligence, modification
(of hardware, firmware or software) or abuse;
4. If the product is subjected to electrical short circuits or transients, accident, fire, flood or Acts of God;
5. Adjustment, maintenance or repair of the product other than in accordance with Digimerge approved procedures; and
6. Use of replacement parts other than those specified by Digimerge.
7. If the products original identification (trademark, serial number, model number) markings have been removed,
defaced or altered.
Digimerge_DVR_Warranty_R5
Page 1
www.digimerge.com
DIGIMERGE MAKES NO CLAIMS OR WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE PRODUCT’S
ABILITY OR EFFECTIVENESS IN PREVENTING OR REDUCING THE RISK OF, OR DAMAGES RESULTING FROM, LOSS
OR THEFT OF PROPERTY OR PERSONAL INJURY. THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE. REPAIR OR REPLACEMENT AS PROVIDED
UNDER THIS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. DIGIMERGE SHALL IN NO
EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES OF ANY
KIND OR CHARACTER, INCLUDING, WITHOUT LIMITATION, PERSONAL INJURY, LOSS OF REVENUE OR PROFITS,
FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR CLAIMS AGAINST THE PURCHASER BY ANY THIRD
PERSON, EVEN IF DIGIMERGE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
No claims or statements regarding the product, whether written or verbal, by salespeople, retailers, dealers or distributors, that
are not contained in this limited warranty or in the owner's manual are authorized by Digimerge and do not modify or expand
this warranty. Some countries, states, or provinces do not allow the exclusion or limitation of implied warranties or the
limitation of incidental or consequential damages for certain products supplied to consumers or the limitation of liability for
personal injury. To the extent that such restrictions on limitations apply to the products, the above limitations and exclusions
may be limited in their application. In that case, when the implied warranties are not allowed to be excluded in their entirety,
they will be limited to the duration of the applicable written warranty, and if damages may not be limited then the above
limitations on damages apply, but only to the greatest extent permitted by local law.
Warranty and Non-Warranty Service:
Warranty service can be received by contacting your Digimerge dealer (during the warranty period). The dealer is required to
first contact Digimerge Technical Support for assistance. In the event the problem cannot be resolved over the phone or via
email, Digimerge will advise to return the product, at customer’s expense, for repair or replacement. Upon receipt of the
defective product, Digimerge will send a repaired or replacement product at Digimerge’s expense to the customer. Dealer
should send product to:
In United States:
Digimerge Returns
Schenker Logistics
2363 E. Perry Road
Suite 171, Dock Door 44
Plainfield, IN 46168
In Canada:
Digimerge Technologies Inc.,
Attention: Repair Department,
250 Royal Crest Court,
Markham, Ontario, Canada,
L3R 3S1
Out of warranty service: Please visit our web site (www.digimerge.com) for the name and location of the Digimerge
authorized service centers.
Digimerge_DVR_Warranty_R5
Page 2
IT’S ALL ON THE WEB!
Tout est sur le Web!
¡Todo está en la Web!
Product Information
Information sur le produit
Información acerca del producto
Quick Start Guides
Guides de démarrage rapide
Guías de arranque rápido
Software Upgrades
Mises à jour du logiciel
Actualizaciones del programa
User Manuals
Guides de l’utilisateur
Guías del usuario
Specification Sheets
Fiches signalétiques
Fichas de especificaciones
Firmware Upgrades
Mises à jour du micro-logiciel
Actualizaciones del microprograma
VISIT / VISITEZ / VISITE
www.digimerge.com
www.digimerge.com
© Digimerge Technology Inc.