Boss TIG 160HF Specifications

MODEL
•
•
BOSS TIG 160HF
BOSS TIG 200HF
Operating Manual
(Owner’
s Manual)
IMPORTANT: Read these instructions before installing, operating, or servicing this system.
First Edition
September, 2008
Manual No. B0807
CONTENTS
SYMBOL LEGEND---------------------------------------------------------------------------------------------------2
STATEMENT OF WARRANTY------------------------------------------------------------------------------------3
1.0
GENERAL INFORMATION-------------------------------------------------------------------------------4
1.01 Notes, Cautions and Warnings------------------------------------------------------------------------4
1.02 Important Safety Precautions--------------------------------------------------------------------------4
1.03 Transporting methods-----------------------------------------------------------------------------------6
2.0
INSTALLATION RECOMMENDATION----------------------------------------------------------------7
2.01 Electrical Input Connections---------------------------------------------------------------------------8
2.02 Specifications--------------------------------------------------------------------------------------------10
2.03 Duty cycle-------------------------------------------------------------------------------------------------10
3.0
OPERATOR CONTROLS-------------------------------------------------------------------------------11
3.01 TIG HF Series controls--------------------------------------------------------------------------------11
3.02 Weld parameter description--------------------------------------------------------------------------13
3.03 Weld parameters for TIG HF series----------------------------------------------------------------13
4.0
SET-UP FOR MMA (STICK) AND GTAW (TIG)----------------------------------------------------14
4.01 Stick welding---------------------------------------------------------------------------------------------15
4.02 DC TIG welding-----------------------------------------------------------------------------------------15
4.03 DC pulse TIG welding---------------------------------------------------------------------------------15
5.0
POWER SUPPLY CONTROLS INDICATORS AND REATURES-----------------------------16
6.0
BASIC TIG WELDING GUIDE--------------------------------------------------------------------------17
6.01 Electrode Polarity---------------------------------------------------------------------------------------17
6.02 Tungsten Electrode Current Ranges---------------------------------------------------------------17
6.03 Tungsten Electrode Types----------------------------------------------------------------------------17
6.04 Guide for Selecting Filler Wire Diameter----------------------------------------------------------17
6.05 Shielding gas selection--------------------------------------------------------------------------------18
6.06 TIG welding parameters for low carbon & low alloy steel pipe-------------------------------18
6.07 Welding parameters for steel------------------------------------------------------------------------18
7.0
BASIC ARC WELDING GUIDE------------------------------------------------------------------------19
7.01 Electrode polarity---------------------------------------------------------------------------------------19
7.02 Effects of stick welding various materials---------------------------------------------------------19
8.0
MAINTENANCE--------------------------------------------------------------------------------------------20
9.0
BASIC TROUBLESHOOTING-------------------------------------------------------------------------20
9.01 Check the item and excrescent phenomenon exclusion method---------------------------20
9.02 TIG welding problems---------------------------------------------------------------------------------22
9.03 Stick welding problems--------------------------------------------------------------------------------23
9.04 Power source problems-------------------------------------------------------------------------------24
10.0 PARTS LIST-------------------------------------------------------------------------------------------------25
11.0 REMARK-----------------------------------------------------------------------------------------------------30
-1BOSS TIG 160HF、200HF Operating Manual
SYMBOL LEGEND
A
V
Hz
Amperage
Stick (SMAW)
Voltage
Pulse Current Function
(GTAW)
Hertz (frequency)
Spot Time (GTAW)
t
SEC
Seconds
Remote outputs control
(Panel/Remote)
%
Percent
Remote Function
DC (Direct Current)
Arc Control (SMAW)
AC (Alternating Current)
Gas Post-Flow Time
t2
2T (GTAW)
Gas Pre-Flow Time
t1
VRD
4T (GTAW)
—
Repeat Function (GTAW)
+
Spot Function (GTAW)
Voltage Reduction
Device Circuit
Negative
Positive
High Frequency Starting
(GTAW)
Gas Input
Lift Start (GTAW)
Gas Output
-2BOSS TIG 160HF、200HF Operating Manual
STATEMENT OF WARRANTY
LIMITED WARRANTY: "BOSS" warrants to customers of its authorized distributors hereafter "BOSS" that its products will be
free of defects in workmanship or material. Should any failure to conform to this warranty appear within the time period
applicable to the BOSS products as stated below, BOSS shall, upon notification thereof and substantiation that the product has
been stored, installed, operated, and maintained in accordance with BOSS’
s specifications, instructions, recommendations and
recognized standard industry practice, and not subject to misuse, repair, neglect, alteration, or accident, correct such defects by
suitable repair or replacement, at BOSS ‘s sole option, of any components or parts of the product determined by BOSS to be
defective.
The BOSS COMPANY MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED. THIS WARRANTY IS EXCLUSIVE AND
IN LIEU OF ALL OTHERS, INCLUDING, BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE.
LIMITATION OF LIABILITY: BOSS shall not under any circumstances be liable for special, indirect or consequential damages,
such as, but not limited to, lost profits and business interruption. The remedies of the Purchaser set forth herein are exclusive
and the liability of BOSS with respect to any contract, or anything done in connection therewith such as the performance or
breach thereof, or from the manufacture, sale, delivery, resale, or use of any goods covered by or furnished by BOSS whether
arising out of contract, negligence, strict tort, or under any warranty, or otherwise, shall not, except as expressly provided herein,
exceed the price of the goods upon which such liability is based. No employee, agent, or representative of BOSS is authorized
to change this warranty in any way or grant any other warranty.
PURCHASER'S RIGHTS UNDER THIS WARRANTY ARE VOID IF REPLACEMENT PARTS OR ACCESSORIES ARE USED
WHICH IN BOSS’S SOLE JUDGEMENT MAY IMPAIR THE SAFETY OR PERFORMANCE OF ANY BOSS PRODUCT.
PURCHASER'S RIGHTS UNDER THIS WARRANTY ARE VOID IF THE PRODUCT IS SOLD TO PURCHASER BY
NON-AUTHORIZED PERSONS.
The warranty is effective for the time stated below beginning on the date that the authorized distributor delivers the products to
the Purchaser. Not with standing the foregoing, in no event shall the warranty period extend more than the time stated plus one
year from the date BOSS delivered the product to the authorized distributor.
POWER SUPPLIES
POWER SUPPLIES & WIRE FEEDERS
MAIN POWER MAGNETICS (STATIC& ROTATING)
1YEAR
ORIGINAL MAIN POWER RECTIFIER
1YEAR
POWER SWITCHING SEMI-CONDUCTORS & CONTROL PC BOARD
1YEAR
ALL OTHER CIRCUITS AND COMPONENTS INCLUDING
1YEAR
BUT NOT LIMITED TO, CONTACTORS, RELAYS,
SOLENOIDS, PUMPS, SWITCHES, MOTORS
Warranty repairs or replacement claims under this limited warranty must be submitted to BOSS by an authorized BOSS repair
facility within thirty (30) days of purchaser’
s notice of any Warranty Claim. No transportation costs of any kind will be paid under
this warranty. Transportation charges to send products to an authorized warranty repair facility shall be the responsibility of the
Purchas er. All returned goods shall be at the Purchaser’
s risk and expense. This warranty supersedes all previous BOSS
warranties.
-3BOSS TIG 160HF、200HF Operating Manual
1.0
GENERAL INFORMATION
1.01
Notes, Cautions and Warnings
Throughout this manual, notes, cautions, and warnings are used to highlight important information. These
highlights are categorized as follows:
NOTE
An operation, procedure, or background information which requires additional emphasis or is helpful in
efficient operation of the system.
CAUTION
A procedure which, if not properly followed, may cause damage to the equipment.
WARNING
A procedure which, if not properly followed, may cause injury to the operator or others in the operating area.
1.02
Important Safety Precautions
WARNING
OPERATION AND MAINTENANCE OF ARC WELDING EQUIPMENT CAN BE DANGEROUS AND
HAZARDOUS TO YOUR HEALTH.
To prevent possible injury, read, understand and follow all warnings, safety precautions and instructions
before using the equipment. Call your local distributor if you have any questions.
GASES AND FUMES
Gases and fumes produced during the Arc welding or cutting process can be dangerous and hazardous to
your health.
l Keep all fumes and gases from the breathing area. Keep your head out of the welding fume plume.
l Use an air-supplied respirator if ventilation is not adequate to remove all fumes and gases.
l The kinds of fumes and gases from the arc welding/cutting depend on the kind of metal being used,
coatings on the metal, and the different processes. You must be very careful when cutting or welding
any metals which may contain one or more of the following:
Antimony
Arsenic
Barium
Beryllium Cadmium Chromium Cobalt
Copper
Lead
Manganese
Mercury
Nickel
Selenium Silver
Vanadium
l Always read the Material Safety Data Sheets (MSDS) that should be supplied with the material you
are using. These MSDSs will give you the information regarding the kind and amount of fumes and
gases that may be dangerous to your health.
l Use special equipment, such as water or down draft welding/cutting tables, to capture fumes and
gases.
l Do not use the welding torch in an area where combustible or explosive gases or materials are
located.
l Phosgene, a toxic gas, is generated from the vapors of chlorinated solvents and cleansers. Remove
all sources of these vapors.
-4BOSS TIG 160HF、200HF Operating Manual
ELECTRIC SHOCK
Electric Shock can injure or kill. The arc welding process uses and produces high voltage electrical energy.
This electric energy can cause severe or fatal shock to the operator or others in the workplace.
l Never touch any parts that are electrically “live”or “hot.”
l Wear dry gloves and clothing. Insulate yourself from the work piece or other parts of the welding
circuit.
l Repair or replace all worn or damaged parts.
l Extra care must be taken when the workplace is moist or damp.
l Install and maintain equipment according to NEC code, refer to relative standards
l Disconnect power source before performing any service or repairs.
l Read and follow all the instructions in the Operating Manual.
FIRE AND EXPLOSION
Fire and explosion can be caused by hot slag, sparks, or the arc weld.
l Be sure there is no combustible or flammable material in the workplace. Any material that cannot be
removed must be protected.
l Ventilate all flammable or explosive vapors from the workplace.
l Do not cut or weld on containers that may have held combustibles.
l Provide a fire watch when working in an area where fire hazards may exist.
l Hydrogen gas may be formed and trapped under aluminum workpieces when they are cut
underwater, or while using a water table. Do not cut aluminum alloys underwater or on a water table
unless the hydrogen gas can be eliminated or dissipated. Trapped hydrogen gas that is ignited will
cause an explosion.
NOISE
Noise can cause permanent hearing loss. Arc welding/cutting processes can cause noise levels to exceed
safe limits. You must protect your ears from loud noise to prevent permanent loss of hearing.
l To protect your hearing from loud noise, wear protective ear plugs and/ or ear muffs. Protect others
in the workplace.
l Noise levels should be measured to be sure the decibels (sound) do not exceed safe levels.
ARC WELDING RAYS
Arc Welding/ Cutting Rays can injure your eyes and burn your skin. The arc welding/cutting process produces
very bright ultra violet and infra red light. These arc rays will damage your eyes and burn your skin if you are
not properly protected.
l To protect your eyes, always wear a welding helmet or shield. Also always wear safety glasses with
side shields, goggles or other protective eye wear.
l Wear welding gloves and suitable clothing to protect your skin from the arc rays and sparks.
l Keep helmet and safety glasses in good condition. Replace lenses when cracked, chipped or dirty.
l Protect others in the work area from the arc rays. Use protective booths, screens or shields.
-5BOSS TIG 160HF、200HF Operating Manual
1.03
Transporting methods
These units are equipped with a handle for carrying purposes.
WARNING: ELECTRIC SHOCK can kill.
DO NOT TOUCH live electrical parts. Disconnect input power conductors from de-energized supply
line before moving the welding power source.
WARNING: FALLING EQUIPMENT can cause serious personal injury and
equipment damage.
l
l
l
Lift unit with handle on top of case.
Use handcart or similar device of adequate capacity.
If using a fork lift vehicle, place and secure unit on a proper skid before transporting.
-6BOSS TIG 160HF、200HF Operating Manual
2.0
INSTALLATION RECOMMENDATION
Installation Environment
TIG HF Series is designed for use in hazardous environments.
Examples of environments with increased hazardous environments are In locations in which freedom of movement is restricted, so that the operator is forced to perform the work
in a cramped (kneeling, sitting or lying) position with physical contact with conductive parts; In locations which
are fully or partially limited by conductive elements, and in which there is a high risk of unavoidable or
accidental contact by the operator, or in wet or damp hot locations where humidity or perspiration
considerable reduces the skin resistance of the human body and the insulation properties of accessories.
Environments with hazardous environments do not include places where electrically conductive parts in
the near vicinity of the operator, which can cause increased hazard, have been insulated.
Installation Location
l
l
l
l
Be sure to locate the welder according to the following guidelines:
In areas, free from moisture and dust.
l In areas, not subjected to abnormal vibration or
In areas, free from oil, steam and corrosive
shock.
gases.
l Place at a distance of 304.79mm or more from
In areas, not exposed to direct sunlight or rain.
walls or similar that could restrict natural airflow
Ambient temperature: between -10 degrees C
for cooling.
to 40 degrees C.
WARNING 1
BOSS advises that this equipment be electrically connected by a qualified electrician.
The following Primary Current recommendations are required to obtain the maximum welding current and
duty cycle from this Power Supply:
Model
Primary supply
lead size
Minimum primary current
circuit size
Current & Duty Cycle
TIG
STICK
TIG
STICK
160A/16.4V@60%
125A/15V@100%
140A/25.6V@60%
125A/25V@100%
TIG 160HF
Minimum 4mm2
220V/22A
240V/20.2A
220V/24.5A
240V/22.5A
TIG 200HF
Minimum 6mm2
220V/32A
240V/29.3A
220V/33.5A 200A/18V@60%
160A/26.4V@60%
240/30.7A 160A/16.4V@100% 140A/25.6V@100%
Table 1
Primary current circuit sizes to achieve maximum current
-7BOSS TIG 160HF、200HF Operating Manual
2.01
Electrical Input Connections
WARNING: ELECTRIC SHOCK can kill; SIGNIFICANT DC VOLTAGE is
present after removal of input power.
DO NOT TOUCH live electrical parts
SHUT DOWN welding power source, disconnect input power employing lockout/ tagging procedures.
Lockout/ tagging procedures consist of padlocking line disconnect switch in open position, removing fuses
from fuse box, or shutting off and red-tagging circuit breaker or other disconnecting device.
Electrical Input Requirements
Operate the welding power source from a single phase 50/ 60 Hz, AC power supply. The input voltage must
match one of the electrical input voltages shown on the input data label on the unit nameplate. Contact the
local electric utility for information about the type of electrical service available, how proper connections
should be made, and inspection required.
The line disconnect switch provides a safe and convenient means to completely remove all electrical power
from the welding power supply whenever necessary to inspect or service the unit.
According to Table 1 and below as a guide to select line fuses for the disconnect switch.
Input Voltage
Fuse Size
220/240V AC
50 Amps
Table 2
Notice: Fuse size is based on not more than 200 percent of the rated input amperage of the
welding power source (Based on Article 630, National Electrical Code).
Figure 1
Electrical input connections
-8-
BOSS TIG 160HF、200HF Operating Manual
Input Power
Each unit incorporates an INRUSH circuit and input voltage sensing circuit. When the MAIN CIRCUIT
SWITCH is turned on, the inrush circuit provides a pre-charging of the input capacitors. The welding machine
will turn on after the input capacitors have charged to full operating voltage (after approximately 1.5 seconds).
Introduction
The importance of correct installation of high frequency welding equipment cannot be overemphasized.
Interference due to high frequency initiated or stabilized arc is almost invariably traced to improper installation.
The following information is intended as a guide for personnel installing high frequency welding machine.
Warning
Explosives
The high frequency section of this machine has an output similar to a radio transmitter. The machine
should NOT be used in the vicinity of blasting operations due to the danger of premature firing.
Computers
It is also possible that operation close to computer installations may cause computer malfunction.
High Frequency Interference
Interference may be transmitted by a high frequency initiated or stabilized arc welding machine in the
following ways:
Direct Radiation
Radiation from the machine can occur if the case is metal and is not properly grounded. It can occur
through apertures such as open access panels. The shielding of the high frequency unit in the
Power Source will prevent direct radiation if the equipment is properly grounded.
Transmission via the Supply Lead
Without adequate shielding and filtering, high frequency energy may be fed to the wiring within the
installation (mains) by direct coupling. The energy is then transmitted by both radiation and
conduction. Adequate shielding and filtering is provided in the Power Source.
Radiation from Welding Leads
Radiated interference from welding leads, although pronounced in the vicinity of the leads,
diminishes rapidly with distance. Keeping leads as short as possible will minimize this type of
interference. Looping and suspending of leads should be avoided where possible.
Re-radiation from Unearthed Metallic Objects
A major factor contributing to interference is re-radiation from unearthed metallic objects close to the
welding leads .Effective grounding of such objects will prevent re-radiation in most cases.
-9BOSS TIG 160HF、200HF Operating Manual
2.02
Specifications
MODEL
TIG 160HF
TIG 200HF
Input voltage and frequency and phases
220/240V 50/60Hz
220/240V 50/60Hz
TIG
4.8kVA
7.0kVA
MMA
5.4kVA
7.4kVA
TIG
160A
200A
MMA
140A
160A
TIG
10~160A
10~200A
MMA
10~140A
10~160A
Open circuit voltage
56/61V
56/61V
Pulse frequency
2Hz/250Hz
2Hz/250Hz
Down slope time
0-5S
0-5S
Post flow time
5S
5S
Duty cycle at 40℃
60%
60%
Weight
9kg
12kg
Dimensions
370×150×245
420×160×265
KVA @ max output
Max current
Output current range
Table 3
2.03
Duty cycle
The duty cycle of a welding power source is the percentage of a ten (10) minute period that it can be
operated at a given output without causing overheating and damage to the unit. If the welding amperes
decrease, the duty cycle increases. If the welding amperes are increased beyond the rated output, the duty
cycle will decrease.
WARNING: Exceeding the duty cycle ratings will cause the thermal overload
protection circuit to become energized and shut down the output until has
cooled to normal operating temperature
Continually exceeding the duty cycle ratings
can cause damage to the welding power source.
NOTICE:
Due to variations that can occur in manufacture products, claimed performance, voltages, ratings, all
capacities, measurements, dimensions and weights quoted are approximate only. Achievable capacities and
ratings in use and operation will depend upon correct installation, use, applications, maintenance and service.
- 10 BOSS TIG 160HF、200HF Operating Manual
3.0
OPERATOR CONTROLS
3.01
TIG HF Series Controls
Figure 2
1.
2.
The function switch:
TIG mode
MMA mode
7-Pin Socket— — Used for the TIG torch switch only.
Figure 3
Pin
Function
2
TIG torch switch
3
TIG torch switch
Table 4
- 11 -
BOSS TIG 160HF、200HF Operating Manual
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Welding Current Control— — Used for regulating to welding current.
Warning Indicator
AC Power Indicator
Main Power Switch
Pulse Switch
DC only (no pulse).
High frequency pulse: the pulse frequency can output 250Hz.
Low frequency pulse: the pulse frequency can output 2Hz.
Down Slope Time and Post Flow Time
Gas Outlet
Positive (+) Socket— — TIG connect the work lead/ MMA connect the electrode holder.
Negative (-) Socket— — TIG connect the TIG torch/ MMA connect the work lead.
Input Power Cable
Gas Inlet
Ground Screw
WARNING
When the welder is connected to the primary supply voltage, the internal electrical
components maybe at primary potential with respect to earth.
- 12 BOSS TIG 160HF、200HF Operating Manual
3.02
Weld parameters description
Figure 4 TIG HF series front panel with parameter description
Parameter
Description
Peak Current
This parameter sets the peak current when in pulse mode.
Welding Current
This parameter sets the welding current when pulse is off.
Base Current
When choice pulse mode this base current by the welding machine in the automatic
hypothesis is 10A.
Pulse Width
When choice pulse mode this pulse width is fixed.
Pulse Freq.
When choice pulse mode this pulse frequency from 2Hz to 250Hz depend on peak
current.
Down Slope Time
This parameter operates in TIG modes only and is used to set the time for the welding
current to ramp down, this control is used to eliminate the crater that can form at the
completion of a weld.
Post-Flow
t2
This parameter operates in TIG modes only and is used to adjust the post gas flow
time once the arc has extinguished. This control is used to dramatically reduce
oxidation of the tungsten electrode.
t2 = 5S
Table 5
3.03
Weld parameter description for TIG HF series
Weld parameter for TIG HF series
Model
TIG 160HF
TIG 200HF
Peak Current
10~160A
10~200A
TIG
10~160A
10~200A
STICK
10~140A
10~160A
Pulse Frequency
2Hz/250Hz/OFF
2Hz/250Hz/OFF
Down Slope Time
0~5S
0~5S
Post-Flow Time
5S
5S
Welding Current
Table 6
Weld parameters for TIG HF series
- 13 -
BOSS TIG 160HF、200HF Operating Manual
4.0
SET-UP FOR MMA (STICK) AND GTAW (TIG)
Conventional operating procedures apply when using the welding power source, i.e. connect work lead
directly to work piece and welding cable is used to electrode holder. Wide safety margins provided by the coil
design ensure that the welding power source will withstand short-term overload without adverse effects. The
welding current range values should be used as a guide only. Current delivered to the arc is dependent on the
welding arc voltage, and as welding arc voltage varies between different classes of electrodes, welding
current at any one setting would vary according to the type of electrode in use. The operator should use the
welding current range values as a guide, and then finally adjust the current setting to suit the application.
Figure 5 Set up for TIG HF series
WARNING:
Before connecting the work clamp to the work and inserting the electrode in the electrode holder
make sure the Primary power supply is switched off.
CAUTION 2:
Remove any packaging material prior to use. Do not block the air vents at the front or rear of the
Welding Power Source.
- 14 BOSS TIG 160HF、200HF Operating Manual
4.01
Stick welding
l
l
l
l
l
Connect work lead to negative terminal.
Connect electrode lead to positive terminal.
Switch machine on.
Set MMA mode.
Set welding current control (see table 7).
Workpiece thickness mm
0.5-2.0
2.0-5.0
5.0-7.0
Electrode diameter mm
1.0-2.0
2.0-3.2
3.2-4.0
Welding current(A)
10-50
50-150
150-250
Table 7
4.02
DC TIG welding
l
l
l
l
l
4.03
Connect work lead to positive terminal.
Connect TIG torch to negative terminal.
Switch machine on.
Set DC TIG mode.
Set welding current control (see table 8).
DC pulse TIG welding
l
l
l
l
l
Connect work lead to positive terminal.
Connect TIG torch to negative terminal.
Switch machine on.
Set pulse high/ pulse low position.
Set welding current control (see table 8).
Workpiece
thickness (mm)
Tungsten
diameter (mm)
Welding current
(A)
0.3-0.5
1-1.6
5-30
0.5-1.2
1.6-2
10-50
1.2-1.6
4-8
1.2-2
1.6-2
10-50
1.2-1.6
4-8
1.2-2
1.6-2
30-70
1.6-2.0
6-9
2-4
2-4
60-100
1.6-2.0
7-10
4-6
3-4
100-200
2.0-2.5
1-15
Table 8
- 15 BOSS TIG 160HF、200HF Operating Manual
Filler wire
diameter (mm)
Argon Gas flow
(L/min)
3-8
5.0
POWER SUPPLY CONTROLS INDICATORS AND REATURES
Figure 6
1.
2.
3.
4.
5.
6.
7.
8.
TIG HF series front panel
Function switch— — Two kind of functions choices, from the top down in turn is:
TIG
STICK
Pulse switch— — -Three kind of choices, from the top down in turn is:
DC only
High frequency pulse TIG welding: The pulse frequency may output the 250Hz.
Low frequency pulse TIG welding: The pulse frequency may output the 2Hz.
7-Pin socket.
Down slope time and post flow time control— — Uses in adjusts when the welding receiving arc the output
current automatic weaken to the zero needing the time, the knob shows is the actual hour, the unit for the
second; and post flow time is fixed 5s.
Welding currents control— — Uses in adjusting the welding current.
Warning indicator— — Red colored light instruction welding machine overload.
AC power indicator— — Green colored light instruction power source is normal.
Main Power switch.
- 16 BOSS TIG 160HF、200HF Operating Manual
6.0
BASIC TIG WELDING GUIDE
6.01
Electrode Polarity
Connect the TIG torch to the - / torch terminal and the work lead to the + / work terminal for direct current
straight polarity. Direct current straight polarity is the most widely used polarity for DC TIG welding. It allows
limited wear of the electrode since 70% of the heat is concentrated at the work piece.
6.02
Tungsten Electrode Current Ranges
Electrode Diameter (mm)
DC current (A)
1.0
30— 60
1.6
60— 115
2.4
100— 165
3.2
135— 200
4.0
190— 280
4.8
250— 340
Table 9
6.03
Current ranges for varies tungsten electrode sizes
Tungsten Electrode Types
Tungsten type
(Ground finish)
Thoriated 2%
Ceriated 2%
Welding Application
Features
DC welding of mild steel, stainless
steel and copper
DC welding of mild steel, stainless
steel, copper, aluminium, magnesium
and their alloys
Excellent arc starting, Long life, high
current carrying capacity
Longer Life, More stable arc, Easier
starting,
Wider
current
range,
Narrower more concentrated arc
Table 10
6.04
Color
code
Red
Grey
Tungsten electrode types
Guide for Selecting Filler Wire Diameter
Filler wire diameter
DC current range (Amps)
1.6
20— 90
2.4
65— 115
3.2
100— 165
4.8
200— 350
Table 11
Filler wire selection guide
Notice:
The filler wire diameter specified in Table 11 is a guide only, other diameter wires may be used
according to the welding application.
- 17 BOSS TIG 160HF、200HF Operating Manual
6.05
Shielding gas selection
Alloy
Shielding gas
Aluminium & alloys
Argon
Carbon steel
Argon
Stainless steel
Argon
Nickel alloy
Argon
Copper
Argon
Titanium
Argon
Table 12
6.06
Shield gas selection
TIG welding parameters for low carbon & low alloy steel pipe
Tungsten type &
diameter
Current range DC
(Amperes)
Filler rod for root pass
Thoriated 2%
3/32”(2.4mm)
120— 170
Yes
Thoriated 2%
3/32”(2.4mm)
100— 160
Yes
Thoriated 2%
3/32”(2.4mm)
90— 130
No
Table 13
6.07
Joint preparation
TIG welding parameters for low carbon & low alloy steel pipe
Welding parameters for steel
Base metal
thickness
(mm)
DC current
for mild
steel (A)
35— 45
40— 50
DC current
for stainless
steel (A)
20— 30
25— 35
Tungsten
diameter
(mm)
Filler rod
diameter (if
require) (mm)
Argon gas
flow rate
(litres/min)
Joint type
1.0
1.6
5— 7
butt/ corner
lap/ fillet
1.2
45— 55
50— 60
30— 45
35— 50
1.0
1.6
5— 7
butt/ corner
lap/ fillet
1.6
60— 70
70— 90
40— 60
50— 70
1.6
1.6
7
butt/ corner
lap/ fillet
3.2
80— 100
90— 115
65— 85
90— 110
1.6
2.4
7
butt/ corner
lap/ fillet
4.8
115— 135
140— 165
100— 125
125— 150
2.4
3.2
10
butt/ corner
lap/ fillet
6.4
160— 175
170— 200
135— 160
160— 180
3.2
4.0
10
butt/ corner
lap/ fillet
1.0
Table 14
DC TIG welding parameters
- 18 -
BOSS TIG 160HF、200HF Operating Manual
7.0
BASIC ARC WELDING GUIDE
7.01
Electrode polarity
Stick electrodes are generally connected to the “+”terminal and the work lend to the “-“terminal but if in
doubt consult the electrode manufacturers literature.
7.02 Effects of stick welding various materials
High tensile and alloy steels
The two most prominent effects of welding these steels are the formation of a hardened zone in the weld
area, if suitable precautions are not taken, the occurrence in this zone of under-bead cracks. Hardened zone
and under-bead cracks in the weld area may be reduced by using the correct electrodes, preheating, using
higher current settings, using larger electrodes size, short runs for larger electrode deposits or tempering in a
furnace.
Manganese steels
The effect on manganese steel slow of cooling from high temperature is to embrittle it. For this reason it
is absolutely essential to keep manganese steel cool during welding by quenching after each weld or skip
welding to distribute the heat.
Cast iron
Most types of cast iron, expect white iron, are weldable. White iron, because of its extreme brittleness,
generally cracks when attempts are made to weld it. Trouble may also be experienced when welding
white-heart malleable, due to the porosity caused by gas held in this type of iron.
Copper and alloys
The most important factor is the high rate of heat conductivity of copper, so making preheating of heavy
sections necessary to give proper fusion of weld and base metal.
Types of Electrodes
Arc welding electrodes are classified into a number of groups depending on their applications. There are
a great number of electrodes used for specialized industrial purposes, which are not of particular interest for
everyday general work. These include some low hydrogen types for high tensile steel, cellulose types for
welding large diameter pipes, etc. The range of electrodes dealt with in this publication will cover the vast
majority of applications likely to be encountered; are all easy to use and all will work on even the most basic of
welding machines.
Metals being joined
Electrode
Comments
Ideal electrodes for all general purpose work. Features
mild steel
6013
include out standing operator appeal, easy arc starting and
low spatter.
All positional electrodes for use on mild and galvanized
mild steel
7014
steel furniture, plates, fences, gates, pipes and tanks etc.
Especially suitable for vertical-down welding.
cast iron
nickel 99%
stainless steel
318L-16
copper, bronze, brass etc.
bronze
5.7ERCUSI-A
high alloy steels, dissimilar
metals, crack resistance, all
hard-to-weld jobs
312-16
Table 15
Suitable for joining all cast irons except white cast iron.
High corrosion resistance. Ideal for dairy work, etc. On
stainless steels.
Easy to use electrode for marine fittings, water taps and
valves, water trough float arms, etc. Also for joining copper
to steel and for bronze overlays on steel shafts.
It will weld most problematical jobs such as springs, shafts,
broken joins mild steel to stainless and alloy steels. Not
suitable for Aluminum.
Types of Electrodes
- 19 -
BOSS TIG 160HF、200HF Operating Manual
8.0
MAINTENANCE
If this equipment does not operate properly, stop work immediately and investigate the cause of the
malfunction. Maintenance work must be performed by an experienced, qualified person only. Any electrical
work must be performed by an electrician or other person properly trained in servicing electrical equipment.
Do not permit untrained persons to inspect, clean or repair this equipment. Use only recommended
replacement parts when servicing this machine.
Periodically clean the inside of the welding power source by using clean dry compressed air of not over
25psi as normal preventive maintenance. At the time of the cleaning, a full inspection of the welding machine
and setup should be performed. Check warning labels on the machine for readability; replace if necessary.
Check input and output connections as well as frame ground connections to the machine to insure that they
are tight and the wires are not frayed or overheated. Inspect internal wiring of machine for loose or frayed
connections; tighten or repair as necessary. It would also be advisable to check connections to wire feeders,
fixtures, etc., at this time. Any damaged cable or hoses should be replaced.
DANGER: HIGH VOLTAGE is present internally even with the control power switch in the
OFF position. Before inspecting, cleaning, or servicing, disconnect and lock out input power to
the power source.
9.0
BASIC TROUBLESHOOTING
WARNING
There are extremely dangerous voltages and power levels present inside this product.
Do not attempt to open or repair unless you are an accredited BOSS service agent and
you have had training in power measurements and troubleshooting techniques.
If major complex subassemblies are faulty, then the welding power source must be returned to an
accredited BOSS service agent for repair.
The basic level of troubleshooting is that which can be performed without special equipment or
knowledge.
9.01 Check the item and excrescent phenomenon exclusion method
- 20 BOSS TIG 160HF、200HF Operating Manual
Troubleshooting Guide
Fault
1. The AC power indicator light is
not lit and welding arc can not
be established.
Cause
Remedy
1. No power input or main power
switches damage.
2. Primary fuse is blown.
3. Indicator damage.
4. Relay PCB damage (for TIG
200HF).
5. Indicator light is open circuit.
1. Input voltage unstable.
1. Check input power or replace
main power switch.
2. Replace primary fuse.
3. Replace indicator light.
4. Replace relay PCB.
1. TIG torch switch leads
disconnected.
2. TIG torch switch damage.
1. Reconnect.
2. The AC power indicator light on
and welding arc can not be
established.
2. Diode PCB damage.
1. Over load.
3. The warning indicator light on.
2. MOSFET damage.
a. No gas flow no
spark.
b. Gas
continues
spark.
are
flow 1. HF starter dirty or spark gaps not
no
enough.
4. TIG mode
2. HF starter damage.
no high
1. TIG torch damage.
frequency
2. Gas hose is cot.
c. No gas flow
starts.
3. Solenoid value damage.
have spark.
4. Power PCB damage.
5. Gas regulator turned off.
d. Gas
flow
1. Welding cable disconnected.
continues have
2. Poor tungsten.
spark.
1. Wrong tungsten.
2. TIG torch bad contact or damage.
3. Gas flow control is improper, not
pure argon gas.
5. TIG mode unstable welding Arc.
4. TIG torch gas hose is cut.
5. TIG torch wrong position (negative
for TIG torch).
6. Control PCB damage.
1. TIG torch/ electrode holder.
2. Wrong setting.
6. TIG and MMA mode incorrect
3. Control PCB damage.
output.
4. Potentiometer
damage
or
disconnected.
1. Function switch select to the TIG
7. MMA (STICK) mode no circuit
mode position.
output.
2. Relay PCB damage.
3. MOSFET damage.
1. Power PCB damage.
8. MMA (STICK) mode unstable
2. Diode PCB damage.
welding arc.
3. Control PCB damage.
1. Power PCB damage.
9. Fan does not run.
2. Fan motor damage.
3. Relay PCB damage.
Table 16
- 21 BOSS TIG 160HF、200HF Operating Manual
5. Replace indicator light.
1. Connect stabilizer or reset power
switch.
2. Replace diode PCB.
1. Reduce current or wait moment.
2. Replace MOSFET.
2. Replace TIG torch switch.
1. Clean the starter and adjust the
spark gap between 0.3~0.8mm.
2. Replace HF starter.
1. Replace TIG torch.
2. Replace gas hose.
3. Replace solenoid value.
4. Replace power PCB.
5. Turn on.
1. Reconnect.
2. Replace tungsten.
1. Choose right tungsten.
2. Replace TIG torch.
3. Replace argon gas capacity.
4. Replace TIG torch.
5. Reconnect.
6.
1.
2.
3.
4.
Replace control PCB.
Replace.
Reset.
Replace control PCB.
Replace or reconnect.
1. Select to MMA mode.
2.
3.
1.
2.
3.
1.
2.
3.
Replace relay PCB.
Replace MOSFET.
Replace power PCB.
Replace diode PCB.
Replace control PCB.
Replace power PCB.
Replace fan motor.
Replace relay PCB.
9.02
TIG welding problems
Weld quality is dependent on the selection of the correct consumables, maintenance of equipment and proper
welding technique.
Description
1. Excessive bead build-up
or poor penetration or
poor fusion at edges of
weld.
2. Weld bead too wide and
flat or undercut at edges
of weld or excessive
burn through.
3. Weld bead too small or
insufficient penetration
or ripples in bead are
widely spaced apart.
4. Weld bead too wide or
excessive bead build up
or excessive penetration
in butt joint.
5. Uneven leg length in
fillet joint.
6. Dirty weld pool.
7. Electrode
melts
or
oxidizes when an arc is
struck.
8. Poor weld finish.
9. Arc flutters during TIG
welding.
10. Welding arc can not be
established.
Possible Cause
Remedy
Welding current is too low.
Increases weld current, and/ or faulty
joint preparation.
Welding current is too high.
Decreases weld current.
Travel speed too fast.
Reduce weld speed.
Travel speed too low.
Increase travel speed.
Wrong placement of filler rod.
Re-position filler rod.
A Electrode contaminated through A Clean the electrode by grinding off
contact with work piece or filler rod
the contaminates.
material.
B Gas contaminated with air.
B Check gas lines for cuts and loose
fitting or change gas cylinder.
A Electrode is connected to the “+” A Connected the electrode to the “-”
terminal.
terminal.
B No gas flowing to welding region.
B Check the gas lines for kinks or
breaks and gas cylinder contents.
C Torch is clogged with dust.
C Clean torch.
D Gas hose is cut.
D Replace gas hose.
E Gas passage contains impurities.
E Dismantle a soft tube from the
torch then raise gas pressure and
blow out impurities.
F Gas regulator turned off.
F Turn on.
G Torch valve is turned off.
G Turn on.
H The electrode is too small for the H Increase electrode diameter or
welding current.
reduce the welding current.
Increase gas flow or check gas line for
Inadequate shielding gas.
gas flow problems.
A Tungsten electrode is too large for A Select the right size electrode.
the welding current.
Refer to basic TIG welding guide.
B Absence of oxides in the weld pool. B Refer basic TIG welding guide for
ways to reduce arc flutter.
A Work clamp is not connected to the A Connect the work clamp to the
work piece or the work/ torch leads
work piece or connect the work/
are not connected to the right
torch leads to the right welding
welding terminals.
terminals.
B Torch lead is disconnected.
B Connect it to the “−”terminal.
C Gas flow incorrectly set, cylinder C Select the right flow rate, change
empty or the torch valve is off.
cylinders or turn torch valve on.
- 22 -
BOSS TIG 160HF、200HF Operating Manual
11. Arc start is not smooth.
A Tungsten electrode is too large for A Select the right size electrode.
the welding current.
Refer to basic TIG welding guide.
B The wrong electrode is being used B Select the right electrode type.
for the welding job.
Refer to basic TIG welding guide
C Gas flow rate is too high.
C Select the correct rate for the
welding job.
D Incorrect shielding gas is being D Select the right shielding gas.
used.
Refer to Basic TIG Welding Guide.
E Poor work clamp connection to E Improve connection to work piece.
work piece.
Table 17
9.03
Stick welding problems
Description
A
1 Gas
pockets
or
B
voids in weld metal
C
(Porosity).
A
2 Crack occurring in
weld metal soon
after
solidification B
commences.
C
3 A gap is left by A
failure of the weld B
metal to fill the root C
of the weld.
D
A
4 Portions of the weld
run do not fuse to B
the surface of the C
metal or edge of the
joint.
D
E
A
Cause
Electrodes are damp.
Welding current is too large.
Surface impurities such as:
grease, paint, etc.
Rigidity of joint.
oil,
Insufficient throat thickness.
Cooling rate is too high.
Welding current is too low.
Electrode too large for joint.
Insufficient gap.
Incorrect sequence.
Small electrodes used on heavy cold
plate.
Welding current is too low.
Wrong electrode angle.
Travel speed of electrode is too high.
Scale or dirt on joint surface.
Non-metallic particles may be trapped
in undercut from previous run.
B Joint preparation too restricted.
C Irregular deposits allow slag to be
5 Non-metallic
trapped.
particles are trapped D Lack of penetration with slag trapped
beneath weld bead.
in the weld metal
(slag inclusion).
E Rust or mill scale is preventing full
fusion.
F Wrong electrode for position in which
welding is done.
Table 18
- 23 BOSS TIG 160HF、200HF Operating Manual
Remedy
A Dry electrodes before use.
B Reduce welding current.
C Clean joint before welding.
A Redesign to relieve weld joint of
severe stresses or use crack
resistance electrodes.
B Travel slightly slower to allow greater
build up in throat.
C Preheat plate and cool slowly.
A Increase welding current.
B Use smaller diameter electrode.
C Allow wider gap.
D Use correct build-up sequence.
A Use larger electrodes and preheat
the plate.
B Increase welding current.
C Adjust angle so the welding is
directed more into the base metal.
D Reduce travel speed of electrode.
E Clean surface before welding.
A If bad undercut is present, clean slag
out and cover with a run from a
smaller diameter electrode.
B Allow for adequate penetration and
room for cleaning out the slag.
C If very bad, chip or grind out
irregularities.
D Use smaller electrode with sufficient
current to give adequate penetration.
Use suitable tools to remove all slag
from corners.
E Clean joint before welding.
F Use electrodes designed for position
in which welding is done, otherwise
proper control of slag is difficult.
9.04
Power source problems
Description
Possible Cause
Remedy
1
The welding arc can not be
established.
A The Primary supply voltage has not A Switch on the primary
been switched on.
supply voltage.
B The welding power source switch is B Switch on the welding
switched off.
power source.
C Loose connections internally.
C Have an accredited BOSS
service agent repair the
connection.
2
Maximum output welding
current can not be achieved
with nominal Mains supply
voltage.
Defective control circuit.
Have an accredited BOSS
service agent inspect then
repair the welder.
Welding current
when welding.
Poor work lead connection to the work
piece.
Ensure that the work lead has a
positive electrical connection to
the work piece.
3
reduces
A Gas hose is cut.
B Gas passage contains impurities.
4
No gas flow when the torch
trigger switch is depressed.
C Gas regulator turned off.
A Replace gas hose.
B Disconnect gas hose from
the rear of power source
then raise gas pressure and
blow out impurities.
C Turn gas regulator on.
Table 19
Notice:
Can move the equipments that the power supply doesn't fixedly mean to link to work with gearing at the some
position.
- 24 BOSS TIG 160HF、200HF Operating Manual
10.0 PARTS LIST
- 25 BOSS TIG 160HF、200HF Operating Manual
- 26 BOSS TIG 160HF、200HF Operating Manual
Figure 7
QTY.
Sequence
Order No
Name
TIG 160HF
TIG 200HF
Sensor A Sensor B Sensor A Sensor B
1
3KITP000505078
BOARD,PCB,CONTROL
(7.820.514-07)
1
3KITP000505017
BOARD,PCB,CONTROL
(7.820.514-06)
2
3KITP000106101
OUTPUT MMA160H
2
2
1
1
1
1
1
OUTPUT MMA160H(SENSOR)
3KITP000106000
2
OUTPUT MMA140
1
1
OUTPUT MMA140 (SENSOR)
2-1
3KITP000506011
BOARD,PCB,MOSFET
2-1
3KITP000106011
BOARD,PCB,MOSFET (7.820.016A)
2-2
3KITP000506021
BOARD,PCB,DIODE
(7.820.010A-02)
2-2
3KITP000506035
BOARD,PCB,DIODE
(7.820.010A-11)
2-2
3KITP000106022
BOARD,PCB,DIODE
(7.820.017-02)
BOARD,PCB,DIODE
(7.820.017-09)
2-2
1
(7.820.005B)
1
1
1
1
1
1
1
1
2-3
2HS7061062
HEATSINK LEFT-LOWER
1
1
2-4
2HS7061063
HEATSINK LEFT-UPPER-A
1
1
2-5
2HS7061064
HEATSINK LEFT-UPPER-B
1
1
2-6
2HS7061060
HEATSINK RIGHT-UPPER
1
1
2-7
2HS7061061
HEATSINK RIGHT-LOWER
1
1
2-3
2HS7061053
HEATSINK LEFT-LOWER
1
1
2-4
2HS7061054
HEATSINK LEFT-UPPER-A
1
1
2-5
2HS7061055
HEATSINK LEFT-UPPER-B
1
1
2-6
2HS7061051
HEATSINK RIGHT-UPPER
1
1
- 27 BOSS TIG 160HF、200HF Operating Manual
2-7
2HS7061052
HEATSINK RIGHT-LOWER
2-8
2FPPM8610005
BRACKET MOUNTING AL 200
2-8
2FPPM8610009
2-9
2-10
2-11
1
1
BRACKET MOUNTING AL 160
1
1
3KITP000106030
THERMOSTAT
1
4VQK2SK2837
MOSFET 2837
4V2HMM20FU020BC812 DIODE ULTRA FAST RECOVERY
1
1
1
1
1
12
12
16
16
12
12
16
16
2-12
4LZQ4X2X5
HOSE FERRITE 4*2*5
36
36
48
48
2-13
2FP8647002
INSULATOR II
16
16
20
20
2-14
2FP8647003
INSULATOR I
1
1
1
1
2-15
2FPBM8610016
BRACKET,HEATSINK MOUNTING
1
1
2-16
2FPBM8610017
BRACKET,HEATSINK MOUNTING
1
1
2-17
2FPBM8610021
BRACKET,HEATSINK MOUNTING I
2
2
2-18
2FPBM8610022
BRACKET,HEATSINK MOUNTING II
2
2
2-15
2FPBM8610000
BRACKET,HEATSINK MOUNTING
1
1
2-16
2FPBM8610001
BRACKET,HEATSINK MOUNTING
1
1
2-17
2FPBM8610019
BRACKET,HEATSINK MOUNTING I
2
2
2-18
2FPBM8610020
BRACKET,HEATSINK MOUNTING II
2
2
2-19
2FPPP8610117
BRACKET,MOSFET/DIODE (8.610.117)
9
9
16
16
2-20
2FPPP8610118
BRACKET,MOSFET/DIODE (8.610.118)
2
2
2-21
2FP7840003
INSULATOR,HEATSINK
1
1
2-21
2FP7840002
INSULATOR,HEATSINK
1
1
2FP7854011
SPACER,NYLON 凹 D5
8
8
8
8
4BFTDQ001D5
SPACER,NYLON 凸 D5
8
8
8
8
2FP7854015
SPACER,NYLON 凹 D4
2
2
2
2
4BFTDQ003D3BK
SPACER,NYLON 凸 D3
2
2
2
2
4ABKBPC3510
RECTIFIER
2
2
2
2
3
3KITP000107010
BOARD,PCB,POWER TIG (7.820.002F-02)
1
1
1
1
4
3KITP000509000
BOARD,PCB,RELAY-INPUT (7.820.000A)
1
1
5
3KITP000113000
FTG,GAS BARBED 1/4 TBG 5/8-18 FEMALE
1
1
1
1
6
3KITP000112004
VALVE DC24V
1
1
1
1
BOARD,PCB,FILTER (7.820.006C-02)
1
1
1
1
2-22
2-23
2-24
7
8
3KITP002801010
BOARD,PCB,SENSOR (7.828.019A-02) (Inside)
9
3BB7725033
BUS BAR,POSITIVE
9
3BB7725032
BUS BAR,POSITIVE
10
3EER10002
COUPLING COIL
10
3EER10001
COUPLING COIL
11
2LAC8807267
OVERLAY CONTROL Tig 200HF BOSS
11
OVERLAY CONTROL Tig 160HF BOSS
1
1
12
2LAC8807266
2LAU8803006
LABEL (+ 0 -)65*10
1
1
13
2LAN8808299
LABEL MANUFACTURERS RATING Tig 200HF
13
2LAN8808298
LABEL MANUFACTURERS RATING Tig 160HF
1
1
- 28 BOSS TIG 160HF、200HF Operating Manual
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
14
2LAM8800003
LABEL GROUND
1
1
1
1
15
2LAU8801001
LABEL GAS INPUT
1
1
1
1
16
2LAM8800001
LABEL VOLTAGE INPUT 240V 1PH
1
1
1
1
17
2FPB6123007
BASE 200/50
FP6.123.007
1
1
17
2FPB6123009
BASE 160/50
FP6.123.009
1
1
BRACKET 7 PIN MOUNTING FP8.604.014
1
1
1
1
2FP7854006
INSULATOR POTENTIONMETER
2
2
2
2
2FP7854007
INSULATOR POTENTIONMETER
2
2
2
2
4V2FLEDN01D7R5
LED HOLDER UPPER
2
2
2
2
4V2FLEDH01D6
LED HOLDER LOWER
2
2
2
2
23
2FP7854004
INSULATOR BULKHEAD FRONT
2
2
2
2
24
2FP7854008
INSULATOR BULKHEAD REAR
2
2
2
2
25
4SXJPG13R5
BUSHING,STRAIN RELIEF PG13.5
1
1
1
1
26
2GS50CC001FP
RECEPTACLE,TWIST LOCK(FEMALE) POWER
2
2
2
2
27
4KCD221BK
SWITCH
1
1
1
1
28
4KYZPN8D24
KNOB
1
1
1
1
29
4KYZPN8E20R3
KNOB
1
1
1
1
30
4FANCA1238
FAN COVER
1
1
1
1
32
4JFT20X27
MOUNT NPRN JJ30
4
4
4
4
33
4FAN001SA1238
FAN
1
1
1
1
34
2PST8634001
INSULATOR FAN
1
1
1
1
35
4WP16S5002
RECEPTACLE 7 PIN
1
1
1
1
36
481CC2KV103
CAPACITOR 3KV103
1
1
1
1
37
8HPU4X6BK001
GAS HOSE 4*6
0.28
0.28
0.37
0.37
4V2FDLEDD5GN
LED GN
2
2
2
2
4V2FDLEDS01D5
LED BASE
2
2
2
2
4V2FDLEDD5RDGN
LED RD/GN
2
2
2
2
4V2FDLEDD5X7
LED BASE
2
2
2
2
40
4WTH1A2W1K
POTENTIONMETER 2W 1K
1
1
1
1
41
4WTH1A2W100K
POTENTIONMETER 2W 100K
1
1
1
1
42
4KNX203
SWITCH KNX203
1
1
1
1
43
4KNX202
SWITCH KNX202
1
1
1
1
47
2FPPT8040001Y
PANEL TOP FP8.040.001Y
1
1
47
2FPPT8040000Y
PANEL TOP FP8.040.000Y
1
1
48
4HDL00001
HANDLE
1
1
1
1
49
2LAW8805000
LABEL WARNING
1
1
1
1
50
2LAS8809040
LABEL BOSS
2
2
2
2
51
3KITP000107022
ARC STARTER
1
1
1
1
18
20
21
38
39
Table 20
- 29 BOSS TIG 160HF、200HF Operating Manual
11.0 Remark
11.1
11.2
11.3
11.4
11.5
11.6
Welding machines rear panels meet the plume to have good to turn on the earth
grounding, by guarantees the welder safety. When welder operation, should wear
protects the mirror, the glove, puts on protects the clothing.
When the electrical network voltage is higher than 240V/260V, the out-put will appear
the class, the overload, the welding machine automatically has stopped outputting and
giving the red candle demonstration warning.
Ambient temperatures high when big electric current long time continuous working, the
welding machine has stopped because of the heat outputting, gets down until the
temperature drop only then restores.
When welding machines do not use temporarily, its depository should maintain dryly,
cleanly. The environment relative humidity is not bigger than 85%.
Storing ambient temperature is -25℃~ +55℃.
When long-time does not use, every two months should electrify a time, a humidity
month of every two week should electrify use a time, by use own thermal row of tide.
- 30 BOSS TIG 160HF、200HF Operating Manual