Epson EMP-82 User`s guide

User’s Guide
Notations Used in This Guide
cCaution:
QTip:
s
g
PROCEDURE
[ (Name) ]
" (Menu Name) "
Indicates procedures which may result in damage or injury if sufficient care is not taken.
Indicates additional information and points which may be useful to know regarding a topic.
Indicates a page where useful information regarding a topic can be found. Click on the page number to
display that page.
Indicates that an explanation of the underlined word or words in front of this symbol appears in the
glossary of terms. Click the underlined word or words to display the corresponding entry in the
"Glossary" section of the "Appendices". s page 68
Indicates operating methods and the order of operations.
The procedure indicated should be carried out in the order of the numbered steps.
Indicates the name of the buttons on the control panel or the remote control.
Example: [Esc] button
Indicates configuration menu items.
Example: "Image"-"Brightness"
When "unit" or "projector" appears in the text of this User’s Guide, it may refer to items which are accessories or optional equipment
in addition to the main projector unit itself.
1
Contents
Projector Features..................................................................4
Part Names and Functions.....................................................6
Front/Top .................................................................................... 6
Control Panel .............................................................................. 7
Rear (EMP-X3) ........................................................................... 8
Rear (EMP-82/62)....................................................................... 9
Base........................................................................................... 10
Remote Control ......................................................................... 11
Adjusting and changing the image
Adjusting the Image Quality .................................................13
Adjusting Computer Images and RGB Video Images .............. 13
Selecting the Projection Quality (Color Mode) ........................ 15
Adjusting the Volume ...........................................................17
Changing the Projected Image (Source Search)..................18
Automatically Detect Incoming Signals and Change
the Projected Image (Source Search)....................................... 18
Changing Directly from the Remote Control............................ 18
Useful Functions
Functions for Enhancing Projection......................................20
Pausing the Image and Sound (A/V Mute) ............................... 20
Freezing the Image (Freeze) ..................................................... 20
Changing the Aspect Ratio (Resizing)...................................... 21
Displaying the Pointer (Pointer) ............................................... 21
Enlarging Part of the Image (E-Zoom) ..................................... 22
Using the Remote Control to Operate the Mouse Pointer
(Wireless Mouse)..................................................................... 23
2
Security functions................................................................. 26
Preventing theft (Password Protect).......................................... 26
Operation Button Lock Function............................................... 29
Configuration Menu
Using the Configuration Menu ............................................. 32
List of Functions................................................................... 33
"Image" Menu ........................................................................... 33
"Signal" Menu ........................................................................... 34
"Settings" Menu ........................................................................ 36
"Extended" Menu ...................................................................... 37
"Info" Menu............................................................................... 39
"Reset" Menu ............................................................................ 40
Troubleshooting
Using the Help ..................................................................... 42
Problems Solving ................................................................. 44
Reading the Indicators............................................................... 44
When the Indicators Provide No Help ...................................... 47
Appendices
Installation............................................................................ 56
Setting Up the Projector ............................................................ 56
Maintenance ........................................................................ 57
Cleaning .................................................................................... 57
Replacing Consumables ............................................................ 58
Saving a User's Logo ........................................................... 64
Contents
Connecting to External Output Equipment ...........................66
Connecting to an External Monitor........................................... 66
Connecting to an external speaker
(when using the EMP-82/62)................................................... 66
Optional Accessories and Consumables..............................67
Glossary ...............................................................................68
List of ESC/VP21 Commands ..............................................70
Command List........................................................................... 70
Cable Layouts ........................................................................... 70
USB Connection Setup ............................................................. 71
List of Supported Monitor Displays.......................................72
Specifications .......................................................................73
Appearance ..........................................................................76
EMP-X3 .................................................................................... 76
EMP-82/62................................................................................ 77
Index.....................................................................................78
3
Projector Features
4
Colour Mode
You can enjoy images of "Photos", "Presentations", "Games", and so on,
in the optimum colour tone by choosing the most suitable mode for your
surroundings. s page 15
Direct Power On & Instant Off
The direct power on function means you can turn the projector on simply
by plugging the power cable into the electrical outlet. s page 38
Also, with the instant-off function you can finish quickly by unplugging
the power cable immediately after use.
Ease of Use
Source search allows you to easily choose the image to project
Simply by pressing the "Source Search" button, the connected picture signal is automatically detected and projected.
Easy to use, big button control panel
For ease of use, buttons are classified and arranged according to their projection and adjustment functions. s page 7
Setup
Projection in Progress Troubleshooting
A single foot design means you do not have to make any difficult
leveling adjustments
You can easily make height adjustments with one hand.
When you turn the projector power on and off a “Beep” sounds
A “Beep” sounds when the power is turned on, after the cooling down
period has finished the confirmation buzzer beeps twice. Once you hear
the confirmation buzzer beep twice, you can unplug the power cable.
Built-in 5W speaker (EMP-82/62 only)
The built-in 5W speaker creates a comfortable volume for a classroom or
conference room containing about 30 people without having to use an
external speaker.
Extensive interface (EMP-82/62 only)
The EMP-82/62 has four video input ports allowing you to connect two
computers and video equipment at the same time. Also, the projector has
audio input ports for both computers and video equipment so the audio
switches automatically when the image is changed.
Projector Features
Security Function
Manage users with password protect
You can set up a password to restrict the use of the projector. s page 26
Operation lock stops the use of all control panel buttons except for
the Power button
This can prevent your settings being changed by accident or on purpose,
when using the projector at an event, at a school, and so on. s page 29
5
Part Names and Functions
6
Front/Top
• Control panel s page 7
• Security lock ( )
s page 69
• Lamp cover s page 59
Open this cover when replacing the
projector's lamp.
• Zoom ring
Adjusts the image size.
• Focus ring
• Air exhaust vent
c Caution:
Adjusts the image focus.
• Remote control light-receiving
Do not touch the exhaust vent
immediately after projecting, or while
projecting, since it becomes hot.
area
Receives signals from the remote control.
• Lens cover
Attach when not using the projector to
prevent the lens from becoming dirty or
damaged.
• Front adjustable foot
Extend and retract to adjust the projection
angle when the projector is placed on a
surface such as a shelf.
• Foot adjust lever
Pull out the foot lever to extend and
retract the front foot.
7
Part Names and Functions
Control Panel
• [Enter] button s page 13, 32
• [Menu] button s page 32
Automatically adjusts analogue RGB images from
computers and RGB video images to the optimum
images.
If a configuration menu or help screen is displayed, it
accepts and enters the current selection.
Displays and closes the configuration menu.
• [Power] button
Turns the projector power on or off.
• [Esc] button
• Indicator states
s page 44
s page 32
The colour of the
indicators and
whether they are
flashing or lit shows
the state of this
projector.
Stops the current function.
Displays the previous
screen or menu while
viewing a configuration
• [Help] button s page 42
• [Source Search] button s page 18
Displays and closes the help, which shows
solutions if a problem occurs.
The input source is automatically searched for in the
following order, and the input image from the connected
equipment is projected.
When using the EMP-X3
When using the EMP-82/62
Computer port
Computer1 port
S-Video port
Computer2 port
Video port
S-Video port
Video port
• [ ] [ ] button
s page 32
Press to correct keystone distortion.
If a configuration menu or help screen
is displayed, it selects menu items and
setting values.
• [ ] [ ] button s page 17, 42
Press to adjust the sound volume. If a
configuration menu or help screen is displayed,
it selects menu items and setting values.
8
Part Names and Functions
Rear (EMP-X3)
• Computer port
Inputs analogue RGB video signals from a
computer and RGB video signals and
component videog signals from other video
sources.
• S-Video port
Inputs S-Videog
signals to the
projector from other
video sources.
• Video port
Inputs composite
videog signals to
the projector from
other video sources.
• Monitor Out port s page 66
• USB port s page 23, 70
Connects the projector to a computer via the
USBg cable when using the wireless mouse
function.
Computer images cannot be projected
by using the USB cable to connect the
computer.
Outputs the projected computer's analogue
RGB signals or RGB video signals to an
external monitor from the source that is
connected to the Computer port. This
feature is not available for video equipment
signals.
• Remote control light-receiving
area
Receives signals from the remote control.
• Power inlet
• Speaker
Connects to the power cable.
• Rear adjustable foot
• Audio port
Input audio signals from connected external
equipment.
When you are connecting two or more pieces of
external equipment that use the same input port,
you need to disconnect one before connecting
the other, or use an audio selector.
9
Part Names and Functions
Rear (EMP-82/62)
• Computer1 port
Inputs analogue RGB video signals
from a computer and RGB video
signals and component videog
signals from other video sources.
• Audio port
This is used to input audio signals
from the equipment that is
connected to the Computer1 port.
• Computer2 port
Inputs analogue RGB video signals
from a computer and RGB video
signals and component videog
signals from other video sources.
• S-Video port
• Inputs S-Videog signals to the projector
• Video port
Inputs composite videog signals to the projector from
other video sources.
• Audio port
This is used to input audio signals
from the equipment that is
connected to the Computer2 port.
• Audio port
This is used to input audio signals from the equipment
that is connected to the S-Video or Video port.
• Remote control
light-receiving area
Receives signals from the remote
control.
• Power inlet
Connects to the power cable.
• Speaker
• Rear adjustable foot
• Monitor Out port s page 66
Outputs the projected computer's analogue RGB
signals or RGB video signals to an external
monitor from the source that is connected to the
Computer1 port. This feature is not available for
video equipment signals.
• Audio Out port
This outputs the audio signals from the currentlyselected input source to external speakers.
• RS-232C port s page 71
Connects the projector to a computer using an
RS-232C cable. This port is for control use and
should not normally be used.
• USB port s page 23, 70
Connects the projector to a computer via the USBg
cable when using the wireless mouse function.
Computer images cannot be projected by the
projector by using the USB cable to connect the
computer.
10
Part Names and Functions
Base
• Foot adjust lever
• Front adjustable foot
• Lens cover string attaching stay
Remove this when suspending the projector
from a ceiling.
• Air intake vent
s page 57
Clean the air intake vent
periodically.
• Air filter (air intake vent)
s page 57, 63
This prevents dust and other foreign particles
from getting inside the projector when air is
drawn in. It should be cleaned and replaced
periodically.
• Suspension bracket fixing points (3 points) s page 56, 67
Attach the optional ceiling mount here when suspending the projector from a ceiling.
11
Part Names and Functions
Remote Control
The following explains the functions shown in the illustration of the EMP-82/62 remote control.
If you position the
over the button icon or button name, a description of that button will appear.
• [Page down] [Page up] buttons s page 24
• Remote control light-emitting area
• [E-Zoom] button ( ) ( ) s page 22
• [Power] button
• [Enter] button s page 24, 32
• [ ] buttons s page 24, 32
• [Esc] button s page 24, 32
• [Freeze] button s page 20
• [Pointer] button s page 21
• [Num] button s page 26
• [A/V Mute] button s page 20
• [Color Mode] button s page 15
• [Computer] button (EMP-X3 only) s page 18
• [Menu] button s page 32
• [Computer1] button (EMP-82/62 only) s page 18
• [Resize] button s page 21
• [Computer2] button (EMP-82/62 only) s page 18
• [Help] button s page 42
• [S-Video] button s page 18
• [Volume] buttons s page 17
• [Video] button s page 18
• [Search] button s page 18
• [Auto] button s page 13
• Numeric buttons s page 26
Adjusting and changing the image
This chapter explains how to adjust the quality of the image, the volume, the colour mode selection and so on, and also how to change the image.
Adjusting the Image Quality .............................. 13
Adjusting the Volume.......................................... 17
• Adjusting Computer Images and RGB Video Images.....13
Changing the Projected Image (Source Search) ..
18
•Automatic Setup ........................................................................ 13
•Adjusting the Tracking .............................................................. 13
•Adjusting the Sync..................................................................... 14
• Selecting the Projection Quality
(Color Mode)15
• Automatically Detect Incoming Signals and Change the
Projected Image (Source Search)18
• Changing Directly from the Remote Control................... 18
Adjusting the Image Quality
Adjusting Computer Images and RGB Video Images
Automatic Setup
Automatic setup detects analogue RGB signals coming from a connected
computer, and automatically adjusts these signals so that the optimum
images can be obtained.
Automatic setup involves adjustment of the following three items:
Trackingg, Position and Sync (synchronisation)g.
If "Auto Setup" in the "Signal" menu is set to "Off", automatic setup is not
carried out. In this case, press the [Auto] button on the remote control or
the [Enter] button on the projector's control panel to make the adjustment
while computer or RGB video images are being projected.
Using the remote control
Using the control panel
13
Adjusting the Tracking
If vertical stripes appear in the projected
computer or RGB video images, and this cannot
be fixed using automatic setup, you will need to
adjust the Trackingg manually using the
following procedure.
PROCEDURE
1 Select "Signal" from the configuration menu, and
A
then select "Tracking".
For details on this operation, refer to "Using the Configuration
Menu". s page 32
Check the buttons you can use and the operations they perform
in the guide at the bottom of the screen.
Using the remote control
Q Tip:
• If you press the [Auto] button on the remote control, or
the [Enter] button on the control panel, while
performing other functions such as E-zoom or Freeze,
these functions are canceled and then the adjustment is
made.
• Sometimes the signals may not be adjusted correctly
depending on the type of computer or RGB video
signals being input. In such cases, use the
configuration menu commands to adjust the tracking
and sync settings manually. s page 14
Using the control panel
14
Adjusting the Image Quality
2 Adjust the tracking until the vertical stripes disappear
A
from the image.
Using the remote control
Using the control panel
Adjusting the Sync
If flickering, fuzziness or interference appear in
computer or RGB video images, and this cannot
be fixed using automatic setup, you will need to
adjust the Sync (synchronisation)g manually
using the following procedure.
PROCEDURE
1 Select "Signal" from the configuration menu, and
A
then select "Sync.".
The tracking value increases or decreases each time a button is
pressed.
3 Press the [Menu] button to exit the configuration
A
menu.
Q Tip:
The image will flash when continuous tracking
adjustment is carried out, but this is normal.
For details on this operation, refer to "Using the Configuration
Menu". s page 32
Check the buttons you can use and the operations they perform
in the guide at the bottom of the screen.
Using the remote control
Using the control panel
15
Adjusting the Image Quality
the synchronization until the horizontal noise
A Adjust
disappears from the image.
2
Using the remote control
Using the control panel
Selecting the Projection Quality
(Color Mode)
The following seven preset colour modes are available for use depending
on the characteristics of the images that are being projected. You can easily
obtain the optimum image quality simply by selecting the colour mode that
corresponds to the projected images. The brightness of the images will
vary depending on which colour mode is selected.
Mode
Photo
Sports
The sync value increases or decreases each time a button is
pressed.
3 Press the [Menu] button to exit the configuration
A
menu.
Q Tip:
• If you adjust the sync without adjusting the trackingg
first, it will not be possible to get the best adjustment
results. Incorrect tracking adjustment may not be
noticeable with some types of picture. However, pictures
with lots of lines and shading will tend to show
incorrect tracking adjustments more clearly, so check
the tracking adjustment first.
• Flickering and fuzziness may also occur when the
brightness, contrastg, sharpness, zoom, and keystone
correction settings are adjusted.
Presentation
Theatre
Game
sRGBg
Blackboard
Application
(When computer and RGB video images are being input)
The images are vivid and brought into contrast. Ideal for projecting
still pictures, such as photos, in a bright room.
(When component video, S-video, or composite video images are
being input)
The images are vivid and brought to life. Ideal for watching TV
programmes and so on in a bright room.
Ideal for giving presentations in a bright room
Gives images a natural tone. Ideal for watching films in a dark room.
Excels at emphasising dark gradations. Ideal for playing video
games in a bright room.
Ideal for images that conform to the sRGB colour standard
Even if you are projecting onto a blackboard (green board), this
setting gives your images a natural tint, just like when projecting
onto a screen
Adjusting the Image Quality
PROCEDURE
Remote control
Each time you press the button, the colour modes change in the
following order.
The current setting appears in the top-right corner of the screen each
time the colour mode is changed. While the colour mode name is
displayed on the screen, it does not change to the next colour mode
setting unless you press the button.
Q Tip:
The colour mode can also be set using the "Color Mode"
command in the "Image" menu. s page 33
16
Adjusting the Volume
The volume of the projector's built-in speaker can be adjusted as follows.
PROCEDURE
Using the remote control
Using the control panel
When the button is pressed to the [ ] side, the volume increases,
and when it is pressed to the [ ] side, the volume decreases.
The volume gauge appears on the screen when the volume is being
adjusted.
Q Tip:
• If the value displayed in the gauge on the screen stops
changing when the volume is being adjusted, it
indicates that the limit for volume adjustment has been
reached.
• The volume can also be adjusted using the
configuration menu. s page 36
17
Changing the Projected Image (Source Search)
Automatically Detect Incoming Signals and Change
the Projected Image (Source Search)
The picture signal input from the connected equipment is automatically
detected and projected.
Computer
S-Video
Video
Q Tip:
18
• When your video equipment is connected, start
playback.
• The following screen is displayed when only the picture
signal projected now is input, or when no picture signal
is input. You can choose the input source from this
screen.
Skip
When using the EMP-X3
When using the EMP-X3
PROCEDURE
1 Perform the Source Search.
A
Using the Remote Control
Using the Control Panel
Changing Directly from the Remote Control
You can use the remote control to change directly to the target input
source.
Remote Control
Changes to the image
from the Computer port.
2 The screen being searched for is displayed, and then
A
the image is projected.
When two or more pieces of equipment are connected, press the
[Source Search] button until the target image is projected.
Changes to the image
from the S-Video port.
Changes to the image
from the Video port.
Useful Functions
This chapter explains useful functions for giving presentations and so on, and the security functions.
Functions for Enhancing Projection ................. 20
Security functions............................................... 26
• Pausing the Image and Sound (A/V Mute) .......................20
• Freezing the Image (Freeze) ...............................................20
• Changing the Aspect Ratio (Resizing)...............................21
• Displaying the Pointer (Pointer) ........................................21
• Enlarging Part of the Image (E-Zoom) .............................22
• Using the Remote Control to Operate the Mouse Pointer
(Wireless Mouse)23
• Preventing theft (Password Protect) ................................. 26
•When Password Protect is Enabled ............................................26
•Setting Password Protect ............................................................27
• Operation Button Lock Function...................................... 29
Functions for Enhancing Projection
Pausing the Image and Sound (A/V Mute)
For example, this can be used if you want to pause the projection for a
moment and focus the audience’s attention on what you are saying. Or if
you are making a computer presentation and you do not want to show
details, such as selecting different files.
20
Freezing the Image (Freeze)
The source image continues to project even when the screen is frozen. You
can still perform operations such as changing files, without projecting any
images.
PROCEDURE
Remote control
PROCEDURE
Remote control
You can turn this function on or off by pressing the [Freeze] button.
Q Tip:
You can turn this function on or off by pressing the [A/V Mute] button.
Q Tip:
• If you use this function when projecting moving
images, the images and sound will still continue to be
played back by the source, and you cannot return to the
point where the A/V mute function was activated.
• The screen display in A/V mute can be chosen from
black, blue, or a logo by using "Extended" -"Display" "A/V Mute" in the configuration menu.
• Sound does not stop.
• Even though the image on the screen is frozen, the
image source continues to project, and so it is not
possible to resume projection from the point where it
was paused.
• Pressing the [Freeze] button also clears configuration
menu displays and help messages.
• The freeze function still works while the E-Zoom
function is being used.
21
Functions for Enhancing Projection
Changing the Aspect Ratio (Resizing)
This function changes the aspect ratiog of images from 4:3 to 16:9 when
component videog, S-Videog, or composite videog images are being
projected.
Images which have been recorded in digital video or onto DVDs can be
viewed in 16:9 wide-screen format.
Displaying the Pointer (Pointer)
This allows you to move a pointer icon on the projected image, and helps
you draw attention to the area you are talking about.
PROCEDURE
When images in Squeeze
modeg are projected at 4:3
When images in squeeze
mode are projected at 16:9
1 Display the pointer.
A
Remote control
PROCEDURE
Remote control
Each time you press the button the pointer appears or
disappears.
The display is changed whenever you press the button.
Q Tip:
You can also make this setting using the "Resize"
command in the "Signal" menu.
22
Functions for Enhancing Projection
2 Move the pointer icon.
A
Enlarging Part of the Image (E-Zoom)
Remote control
This is useful when you want to see images in greater detail, such as graphs
and details in a table.
Pointer icon
Q Tip:
You can use the "Pointer Shape" command in the
"Settings" menu to change the shape of the pointer to
one of three different shapes.
s page 36
PROCEDURE
1 Start E-Zoom.
A
Remote control
23
Functions for Enhancing Projection
2 Move the cross to the area of the image that is to be
A
enlarged or reduced.
Remote control
Using the Remote Control to Operate the Mouse
Pointer (Wireless Mouse)
If the USB terminal of a computer and the USB terminal on the back of
this projector are connected by a commercially available USB A-B cable*,
you can use the projector’s remote control like a wireless mouse to control
the computer’s mouse pointer.
*USB cable included with the EMP-82/62.
Cross
3 Enlarge.
A
Computer
Windows 98/2000/Me/XP Home Edition/XP Professional
Macintosh (OS 8.6–9.2/10.0–10.3)
Remote control
You can reduce the enlarged image by pressing the [-] button.
To cancel the E-Zoom, press the [Esc] button.
Q Tip:
• The enlargement ratio will appear on the screen.
• You can scroll the screen by tilting the [ ] button.
• The selected area can be enlarged to between 1- 4 times,
in 25 incremental steps.
To USB port
To USB port
USB cable
24
Functions for Enhancing Projection
Q Tip:
• The USB cable can only be connected to computers
with a standard USB interface. If using a computer
which is running Windows, the computer must have
had a full version of Windows 98/2000/Me/XP Home
Edition/XP Professional installed. If the computer is
running a version of Windows 98/2000/Me/XP Home
Edition/XP Professional that has been upgraded from
an earlier version of Windows, correct operation cannot
be guaranteed.
• It may not be possible to use the mouse function under
some versions of both the Windows and Macintosh
operating systems.
• Some computer settings may have to be changed in
order for the mouse function to be used. Consult the
documentation for the computer for further details.
Once the connection has been made, the mouse pointer can be operated as
follows.
Moving the mouse pointer
Mouse clicks
Left click
Right click
Double-click: Press twice in rapid
succession.
Drag and drop
This is useful for displaying the
previous or next slide in a
PowerPoint slideshow.
To previous slide
1. Hold down the [Enter] button
and tilt and drag the [ ] button.
2. Release the [Enter] button to
drop at the desired location.
To next slide
Functions for Enhancing Projection
Q Tip:
• If the mouse button settings are set to reverse on the
computer, the operation of the remote control buttons
will also be reversed.
• The wireless mouse function cannot be used while the
following functions are being used.
· While a configuration menu is being displayed
· While a help menu is being displayed
· While the E-Zoom function is being used
· While a user's logo is being captured
· Pointer function
· While adjusting sound volume
25
Security functions
26
Preventing theft (Password Protect)
When the Password Protect function is activated, people who do not know
the password will not be able to use the projector to project images, if the
power has been disconnected since the password was last entered correctly.
Furthermore, the user's logo that is displayed on the background of the
screen cannot be changed. This is effective against theft. At the time of
purchase, the password protection function is not enabled.
If you leave the power cable connected to the electrical outlet and turn the
projector's power on when it is in standby mode, projection will start
without the password entry screen appearing. The password entry screen
will only be displayed when the power is turned on for the first time after
the power cable has been disconnected and then reconnected. If Direct
Power On is set to "On" and you are using a circuit breaker or similar to
centrally control the power, the password entry screen will be displayed the
first time the projector is turned on after the power supply is restored.
Q Tip:
When Password Protect is Enabled
When "Power On Protect" is enabled (On)
When the power is turned on for the first time after the projector's power
cable is connected to an electrical outlet, or when Direct Power On is
carried out, the following password entry screen will be displayed.
Remote control
Keep
Pressed
Numeric buttons
While holding down the [Num] button, press the numeric keypad buttons
to enter the password. If the password is entered correctly, projection will
start.
• If an incorrect password is entered three times in
succession, the message "The projector’s operation will
be locked." will be displayed for approximately five
minutes, and then the projector will switch to standby
mode. If this happens, disconnect the power plug from
the electrical outlet and then reinsert it and turn the
projector's power back on. A window requesting you to
enter the password will be displayed, so enter the
correct password.
If you happen to forget the password, make a note of the
"Request Code: xxxxx" number that appears in the
Password screen and contact the nearest address
provided in the "International Warranty Conditions"
section of the Safety Instructions/World-Wide Warranty
Terms booklet.
• If you continue to repeat the above operation and input
the wrong password thirty times, the following message
will be displayed and the projector will not accept
password entries any more.
"The projector’s operation will be locked. Contact the
nearest address provided in the "International
Warranty Conditions" section of the Safety
Instructions/World Wide Warranty Terms booklet."
27
Security functions
When "Password Timer" is set to "On" and "Timer" is used
The password entry screen will not be displayed at all when the power is
turned on until the length of time that has been set has elapsed. When the
set length of time has elapsed, the password entry screen will be displayed
each time the power is turned on. The length of time referred to here is the
total illumination time for the projector's lamp from the point when the
projector's menu is closed.
If "Password Timer" is set to "Off", the password entry screen will be
displayed each time the power plug is disconnected and reinserted from the
electrical outlet. If the projector’s power is on when it is in standby mode,
the password entry screen will not be displayed.
When "User’s Logo Protect" is enabled (On)
If an attempt is made to carry out any of the following user logo
operations, a message is displayed and the setting cannot be changed. To
change the setting, set "User’s Logo Protect" to "Off" first. s page 28
• Capturing a user's logo
• When the "Extended" - "Display" - "Display Background" menu , or the
"Extended" - "Display" - "A/V Mute" menu, is changed from "Logo" to
"Black" or "Blue", or changed from "Black" or "Blue" to "Logo".
• When the "Extended" - "Display" - "Startup Screen" menu ("On" or
"Off") is changed.
Setting Password Protect
Use the following procedure to set Password Protect.
PROCEDURE
1 Hold down the [Freeze] button for approximately 5
A
seconds.
The "Password Protect" menu will be displayed.
Remote control
Q Tip:
• If Password Protect has already been enabled, the
"Password" screen will be displayed.
If the password has been entered correctly, the
"Password Protect" menu will be displayed.
s "When Password Protect is enabled" page 26
• If Password Protect is set to "On", attach the accessory
Password Protect sticker to your preferred position on
the projector as a theft-prevention measure.
2 Turn "Power On Protect" on.
A
(1) Select "Power On Protect", and then press the [Enter]
button.
(2) Select "On", and then press the [Enter] button.
(3) Press the [Esc] button.
28
Security functions
3 Turn "Password Timer" on.
A
If you don't use this setting, proceed to step 4.
(1) Select "Password Timer", and then press the [Enter]
button.
(2) Select "On", and then press the [Enter] button.
(3) Press the [Esc] button.
(4) Select "Timer" and then press the [Enter] button.
(5) While holding down the [Num] button, use the numeric
keypad buttons to enter the setting time within the range of
1 to 9999 hours and then press the [Enter] button.
If you make a mistake entering the time, press the [Esc]
button and re-enter the time.
When you have finished using the "Password Protect"
menu, the countdown for the elapsed time will start.
4 Turn "User’s Logo Protect" on.
A
(1) Select "User’s Logo Protect", and then press the [Enter]
button.
(2) Select "On", and then press the [Enter] button.
(3) Press the [Esc] button.
5 Enter the password.
A
(1) To set a password, select "Password" and then press the
[Enter] button.
(2) The message "Change the password?" will be displayed,
so select "Yes" and then press the [Enter] button. The
default setting for the password is "0000", but you should
change this to your own desired password. If you select
"No", the screen shown at step 1 will be displayed again.
(3) While holding down the [Num] button, use the numeric
keypad buttons to enter a 4-digit number. The number
entered will be displayed as "* * * *". Once four digits
have been entered, the confirmation screen will be
displayed.
(4) Re-enter the password.
The message "The new password is stored." will be
displayed. If you enter the password incorrectly, a message
will be displayed prompting you to re-enter the password.
29
Security functions
Operation Button Lock Function
This function locks the buttons on the projector's control panel.
This function is useful at times such as during show events so that only
projection is carried out deactivating all buttons operation, or in places
such as schools to limit the range of buttons that can be operated.
2 Set to "On".
A
If set to "On", none of the buttons on the control panel except
the [Power] button can be operated.
PROCEDURE
1 From the configuration menu, select "Settings" A
"Operation Lock".
For details on this operation, refer to "Using the Configuration
Menu". s page 32
Check the buttons you can use and the operations they perform
in the guide at the bottom of the screen.
Using the remote control
Using the control panel
Using the remote control
Using the control panel
Security functions
3 When the confirmation message is displayed, select
A
"Yes".
The control panel buttons will be locked in accordance with the
selected setting.
Q Tip:
There are two methods to cancel the projector's control
panel lock.
• Using remote control, change the "Settings" "Operation Lock" in the configuration menu to "Off" .
• Hold down the projector's [Enter] button continuously
for about 7 seconds, a message will be displayed and the
lock will be cancelled.
30
Configuration Menu
This chapter explains how to use the configuration menu and its functions.
Using the Configuration Menu........................... 32
List of Functions ................................................. 33
• "Image" Menu.....................................................................33
• "Signal" Menu.....................................................................34
• "Settings" Menu..................................................................36
• "Extended" Menu ...............................................................37
• "Info" Menu ........................................................................39
• "Reset" Menu ......................................................................40
Using the Configuration Menu
1 Selecting from
A
the top menu
2 Selecting from
A
the sub menu
32
3 Changing the
A
selected item
Buttons used
Using the control panel
Top menu
Using the remote control
guide
Sub menu (Settings)
Select the setting to change.
List of Functions
33
"Image" Menu
The items that can be set will vary depending on the input source that is currently being projected. Setting details are saved separately for each source.
Computer/RGB video
Screen shot from EMP-X3
Sub-menu
Color Mode
Brightness
Contrastg
Color Saturation
Tint
Sharpness
Color Temp.g
(EMP-X3 only)
Color
Adjustment
Reset
Component videog/ Composite videog/ S-Videog
Screen shot from EMP-X3
Function
Select the quality of the image to suit your surroundings. s page 15
Adjusts the image brightness.
Adjusts the difference between light and shade in the images.
Adjusts the colour saturation for the images.
(Adjustment is only possible when component video or NTSC signals are being input.) Adjust the image tint.
Adjusts the image sharpness.
You can adjust the overall tint of images. If you select "High", images appear bluish, and if you select "Low", images appear reddish.
(This item cannot be selected if "sRGBg" has been selected as the "Color Mode" setting in the "Image" menu.)
Adjusts the red, green, and blue colour strength of the image.
Abs. Color Temp.: You can adjust the overall tint of images. You can adjust tints in 10 stages from 5000 K to 10000 K. (EMP-82/62 only)
Red: Adjust the saturation of the red component.
Green: Adjusts the saturation of the green component.
Blue: Adjusts the saturation of the blue component.
(This item cannot be selected if "sRGBg" has been selected as the "Color Mode" setting in the "Image" menu.)
Resets all adjustment values for the "Image" menu functions to their default settings.
If you would like to return all menu items to their default, see "Reset All". s page 40
34
List of Functions
"Signal" Menu
The items that can be set will vary depending on the input source that is currently being projected. Setting details are saved separately for each source.
Computer/RGB video
Screen shot from EMP-X3
Sub-menu
Auto Setup
Component videog
Composite videog/ S-Videog
Screen shot from EMP-X3
Function
Selects whether the automatic adjustment function for automatically optimising images when the input source is changed is turned "On" or
"Off". s page 13
Trackingg
Adjusts computer images when vertical stripes appear in the images. s page 13
Sync.g
Adjusts computer images when flickering, fuzziness or interference appear in the images. s page 14
Position
Moves the image display position vertically and horizontally.
Progressive (Adjustment is only possible when composite Video or S-Video signals are being input.)
Off: IP conversion is carried out for each field in the screen. This is ideal for using when viewing images with a large amount of movement.
On: Interlacedg (i) signals are converted into progressiveg (p) signals. This is ideal for using when viewing still images.
Computer
Selects the input signal in accordance with the equipment that is connected to the Computer port.
Input (EMP- If set to "Auto" the input signal is set automatically in accordance with the connected equipment.
X3 only)
If the colours do not appear correctly when you select "Auto", select the appropriate signal for the connected equipment manually.
Computer1
Selects the input signal in accordance with the equipment that is connected to the Computer1 port.
Input (EMP- If set to "Auto" the input signal is set automatically in accordance with the connected equipment.
82/62 only) If the colours do not appear correctly when you select "Auto", select the appropriate signal for the connected equipment manually.
Computer2
Selects the input signal in accordance with the equipment that is connected to the Computer2 port.
Input (EMP- If set to "Auto" the input signal is set automatically in accordance with the connected equipment.
82/62 only) If the colours do not appear correctly when you select "Auto", select the appropriate signal for the connected equipment manually.
35
List of Functions
Sub-menu
Function
Video Signal (Adjustment is only possible when composite video/S-Video signals are being input.)
Sets the video signal format.
With the "Auto" function, image signals are recognized automatically. If interference appears in the projected images or no images appear when
you select "Auto", select the appropriate signal manually.
Resize
Sets the aspect ratiog for projected images. s page 21
Reset
Resets all adjustment values on the "Signal" menu to their default settings, except "Computer Input", "Computer1 Input", and "Computer2
Input".
If you would like to return all menu items to their default, see "Reset All". s page 40
36
List of Functions
"Settings" Menu
Screen shot from EMP-X3
Sub-menu
Keystone
Auto
Keystone
(EMP-82/62
only)
Operation
Lock
Pointer
Shape
Brightness
Control
Volume
Reset
Screen shot from EMP-82/62
Function
Corrects vertical keystone distortion in images.
Sets the function for automatically detecting the projector angle and correcting keystone "On" or "Off" when the projector is tilted vertically.
This function is only enabled when the "Projection" command in the "Extended" menu is set to "Front". If it is set to something other than
"Front", this menu cannot be selected.
When set to "On", the operation of all buttons on the projector's control panel except for the [Power] button will be disabled. s page 29
The shape of the pointer can be selected. s page 21
Pointer 1:
Pointer 2:
Pointer 3:
This lets you set the lamp brightness to one of two settings.
Select "Low" if the images being projected are too bright such as when projecting images in a dark room or onto a small screen.
When "Low" is selected, the brightness of the images is reduced, the amount of electricity consumed and noise produced during projection are
reduced, and the lamp's operating life is extended. Also the fan noise is reduced. (Electrical consumption: about an 35 W decrease, lamp life:
about 1.5 times longer, Fan noise: about 20% reduction)
Adjusts the volume. s page 17
Resets all adjustment values on the "Settings" menu to their default settings.
If you would like to return all menu items to their default, see "Reset All". s page 40
37
List of Functions
"Extended" Menu
Screen shot from EMP-X3
Sub-menu
Display
User’s Logo
Projection
Screen shot from EMP-82/62
Function
This lets you make settings related to the projector's display.
Message:
Sets whether the input source name or colour mode name or a message is displayed on the screen ("On") or not displayed ("Off") at times such
as when the input source or colour mode is changed or when no image signals are being input.
Display Background:
Sets the screen status to "Black", "Blue", or "Logo" when no image signals are being input.
Startup Screen:
The startup screen (the image projected when starting the projector) is displayed when starting (On)/ or not displayed when starting (Off). The
setting is enabled after turning the power supply off and then back on.
A/V Mute:
You can choose the Screen display in A/V mute from "Black", "Blue", and "Logo".
Change the user's logo that is displayed as a background and displayed during A/V Mute. s page 64
Sets the projection position for the projector. s page 56
"Front" "Front / Ceiling" "Rear" "Rear / Ceiling"
By holding down the [A/V Mute] button for about 5 seconds, you can change the projection setup in the following ways.
Front
Front Ceiling
Rear
Rear Ceiling
38
List of Functions
Sub-menu
Operation
Link 21L
(EMP-X3
only)
Standby
Mode
(EMP-82/62
only)
COM Port
(EMP-82/62
only)
Language
Reset
Function
Direct Power On:
Sets whether direct power on is enabled ("On") or disabled ("Off").
When you set to "On" and leave the power cable connected to a wall socket, be aware of that sudden surges of electricity that may occur when
power comes back on after a power outage may cause the projector to turn on automatically.
Sleep Mode:
Sets whether projection stops automatically ("On") or not ("Off") when no operations are carried out for approximately 30 minutes while no
image signals are being input.
High Altitude Mode:
When using above an altitude of about 1500m, set to "On".
Sets whether the EMP Link 21L utility software is being used or not.
To enable the EMP Link 21L, turn the projector's power off and wait until the cool down period has finished.
Set to "Network On" to use network monitoring and control functions and the standby monitor out function while the projector is in standby
mode.
If you change the setting, the new setting will be enabled after the power is turned off.
•We provide softwares* for network monitoring and controlling projectors.
•When set to "Network On", the Power indicator will flash orange and then remain orange after disconnecting the power plug and reinserting it
into the electrical outlet.
This can be set to either "RS-232C" or "USB", depending on the port that is being used for communication with a computer.
If you change the setting, the new setting will be enabled after the power is turned off.
Sets the language for message displays.
Returns "Display" and "Operation" settings in the "Extended" menu (except for "High Altitude Mode") to their default settings.
If you would like to return all menu items to their default, see "Reset All". s page 40
* EMP Monitor : Allows you to monitor multiple projectors on the network and control them all at once using functions such as turning the power on and off and
switching input sources.
To use the EMP Monitor, an adapter and cable for conversion are required. The followings are available products. (As of May, 2005)
For details on the products, visit LANTRONIX's website.
Adapters: UDS100, UDS200 (LANTRONIX)
Cables: For the UDS100 RS-232C cable (straight, mini D-Sub9pin female/mini D-Sub25pin male)
For the UDS200 RS-232C cable (cross, mini D-Sub9pin female/mini D-Sub9pin female)
For the detailed and current information about the software, please visit the following website.
http://esupport.epson-europe.com/downloads/en/
39
List of Functions
"Info" Menu
Lets you check the status of the image signals being projected and the status of the projector. (Display only)
Computer/RGB Video/Component videog
Sub-menu
Lamp Hours
Composite videog/ S-Videog
Function
Shows the cumulative lamp operating time.
If it reaches the lamp warning time, the characters are displayed in yellow. The cumulative operating time from 0 to 10 hours will be displayed as
"0H". From "10H" onwards, the display will be in units of 1 hour.
Source
Displays the input source which is currently being projected.
Input Signal Displays the input signal settings.
(Does not appear when the input source is composite video or S-video.)
Resolution
Displays the input resolution.
(Does not appear when the input source is composite video or S-video.)
Video Signal Shows the video signal format.
(Not displayed for computer, RGB video, or component video images.)
Refresh
Displays the refresh rate.
Rateg
(Does not appear when the input source is composite video or S-video.)
Sync.g Info Information from this menu may be required when you ask for service from your dealer or from the nearest address provided in the
"International Warranty Conditions" section of the Safety Instructions/World Wide Warranty Terms booklet.
(Does not appear when the input source is composite video or S-video.)
40
List of Functions
"Reset" Menu
Sub-menu
Reset All
Reset Lamp
Hours
Function
Resets all items in all menus to their default settings.
The "Computer Input", "Computer1 Input", "Computer2 Input", "User’s Logo", "Lamp Hours" and "Language" settings will not be reset to their
defaults.
Clear the cumulative lamp operating time and reset to "0H". Perform this procedure when you replace the lamp.
Troubleshooting
This chapter describes how to identify problems and what to do if a problem is found.
Using the Help..................................................... 42
Problems Solving................................................ 44
• Reading the Indicators........................................................44
•Power indicator lights red .......................................................... 44
•Lamp or Temp indicator flashes orange .................................... 45
• When the Indicators Provide No Help ..............................47
•Problems relating to images ...................................................... 48
•Problems when projection starts................................................ 53
•Other problems .......................................................................... 53
Using the Help
42
If a problem occurs with the projector, the Help function uses on-screen
displays to assist you in solving the problem. It uses a series of menus in a
question and answer format.
2 Select a menu item.
A
PROCEDURE
1 Display the Help menu.
A
Using the remote control
Using the control panel
Using the remote control
3 Confirm the selection.
A
Using the remote control
Using the control panel
Using the control panel
Using the Help
4 Repeat the operations in steps 2 and 3 to proceed
A
through the menu to more detailed items.
5 Press the [Help] button to exit the help menu.
A
Q Tip:
If the Help function does not provide a solution to the
problem, refer to "Problem Solving" U page 44
43
Problems Solving
44
If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators" below.
If the indicators do not show clearly what the problem might be, refer to "When the Indicators Provide No Help". s page 47
Reading the Indicators
The projector is provided with the following three indicators which indicate the operating status of the projector.
Indicates the operating status of the projector.
Orange : Standby condition
Projection starts again when the [Power] button is pressed.
You can disconnect the power plug from the electrical outlet when the status light is in this condition.
Green : Warm-up in progress
Warm-up time is approximately 30 seconds. After warm-up is complete, the indicator will stop flashing.
Green : Projection in progress
Indicates the projection lamp status.
Indicates the internal temperature status.
The following tables show what the indicators mean and how to remedy problems that they indicate.
If all indicators are switched off, check that the power cable is connected correctly and that power is being supplied normally.
: lit
Power indicator lights red Abnormal
Status
Power
Red
Cause
: flashing
: off
Remedy or Status
Internal error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your
dealer or the nearest address provided in the "International Warranty Conditions" section of the
Safety Instructions/World-Wide Warranty Terms booklet.
Fan related error/
Sensor error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your
dealer or the nearest address provided in the "International Warranty Conditions" section of the
Safety Instructions/World-Wide Warranty Terms booklet.
Red
Red
Power
Red
Red
45
Problems Solving
: lit
Status
Power
Red
Cause
High temperature error
(overheating)
Red
Power
Red
Red
Lamp problem
Lamp timer failure
Lamp cover is open
Power
Red
Orange
Cause
High temperature warning
: off
Remedy or Status
The lamp will turn off automatically and projection will stop. Wait for about 5 minutes. After
about 5 minutes the projector will switch to standby mode, so check the following two points.
After checking, press the [Power] button to turn the power back on.
•Check that the air filter and air exhaust vent are clear, and that the projector is not positioned
against a wall.
•If the air filters are blocked, clean or replace them. s page 57, 63
If this does not solve the problem and the projector continues to overheat or the indicators continue
to show a problem when the power is turned on, stop using the projector, disconnect the power cable
from the wall outlet, and contact your dealer or the nearest address provided in the "International
Warranty Conditions" section of the Safety Instructions/World-Wide Warranty Terms booklet.
Take out the lamp and check if it is broken. s page 59
If the lamp is not broken, put it back in and then turn the power on. If the lamp still does not turn
on, replace it with a new lamp.
If this does not solve the problem, stop using the projector and disconnect the power cable from
the electrical outlet. Then contact your dealer or the nearest address provided in the "International
Warranty Conditions" section of the Safety Instructions/World-Wide Warranty Terms booklet
If the lamp is broken replace it with a new lamp, or contact your local dealer for further advice. If
replacing the lamp yourself, be careful to avoid pieces of broken glass. (Projection cannot be
carried out until the lamp is replaced.)
Check that the lamp and the lamp cover are securely installed. If the lamp or lamp cover is not
securely installed, the lamp will not switch on.
When using above an altitude of about 1500 m, make sure you set the "High Altitude Mode" to
"On".
: lit
Lamp or Temp indicator flashes orange Warning
Status
: flashing
: flashing
: off
Remedy or Status
(This is not an abnormality, but if the temperature rises too high again, projection will stop
automatically.)
•Check that the air filters and air exhaust vent are clear and that they are not up against a surface
such as a wall.
•If the air filters are clogged, clean or replace them. s page 57, 63
46
Problems Solving
: lit
Status
Lamp replacement notification
Power
Orange
Q Tip:
Cause
: flashing
: off
Remedy or Status
Replace the lamp with a new one. s page 59
If you continue to use the lamp after it has passed the replacement period, the possibility that the
lamp may break will increase. Replace the lamp with a new one as soon as possible. The Power
indicator status will vary depending on the projector status at the time.
• If the projector is not operating properly even though the indicators are all showing normal, refer to "When the Indicators Provide No
Help" on the following page.
• If an indicator is showing a status which does not appear in the previous tables, contact your dealer or the nearest address provided in
the "International Warranty Conditions" section of the Safety Instructions/World-Wide Warranty Terms booklet.
47
Problems Solving
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each problem.
Problems relating to images
Problems when projection starts
No images appear s page 48
Projection does not start, the projection area is completely black, the
projection area is completely blue, and so on.
Power does not turn on s page 53
Projection stops automatically s page 48
Other problems
The message "Not Supported." is displayed s page 49
No sound can be heard or the
sound is faint s page 53
The message "No Signal." is displayed s page 49
Images are fuzzy or out of focus s page 50
Interference or distortion appear in images s page 50
Problems such as interference, distortion or black & white checked
patterns appear.
Image is truncated (large) or small s page 51
Only part of the image is displayed.
Image colours are not right s page 52
The whole image appears purplish or greenish, images are black &
white, colours appear dull, and so on.
(Computer monitors and LCD screens have different colour
reproduction performance, so that the colours projected by the
projector and the colours appearing on the monitor may not
necessarily match, but this is not a sign of a problem.)
Images appear dark s page 52
Nothing appears on the external monitor s page 53
The remote control does not work
s page 54
48
Problems Solving
Problems relating to images
No images appear
Check
Remedy
Was the [Power] button pressed?
Press the [Power] button to turn the power on.
Are the indicators switched off?
The power cable is not connected correctly or power is not being supplied normally. Connect the
projector's power cable correctly.
Check that your power supply socket is working.
Is A/V Mute mode active?
Press the [A/V Mute] button on the remote control to cancel the mute. s page 20
Have the configuration menu settings
been made correctly?
Reset all of the settings. "Reset" - "Reset All" s page 40
Is the projected image completely black?
Some input images, such as screen savers, may be completely black.
Only when projecting computer images
Are the image signal format settings
correct?
If a composite videog or S-Videog source is connected to the projector, use the "Video Signal" menu
command to select the signal format. "Signal" - "Video Signal" s page 35
Only when projecting images
from a video source
Projection stops automatically
Check
Is "Sleep Mode" set to "On"?
Remedy
When the "Sleep Mode" menu command has been set to "On", the lamp turns off automatically if no
operations are carried out for about 30 minutes while no video signal is being input. The Power indicator
is lit orange at this time. Press the [Power] button to turn the power on. If you do not want sleep mode to
be used, change the "Sleep Mode" setting to "Off". "Extended" - "Operation" - "Sleep Mode"
s page 38
49
Problems Solving
The message "Not Supported." is displayed
Check
Are the image signal format settings
correct?
Remedy
If a composite videog or S-Videog source is connected to the projector, use the "Video Signal" menu
command to select the signal format. "Signal" - "Video Signal" s page 35
Only when projecting images
from a video source
Does the mode match the frequency and
resolution of the image signals?
Only when projecting computer images
Refer to the documentation provided with your computer for details on changing the resolution and
frequency of the image signals being output from the computer.
"List of Supported Monitor Displays" s page 72
The message "No Signal." is displayed
Check
Remedy
Are the cables connected correctly?
Check that all of the cables required for projection are securely connected.
Has the correct video input port been
selected?
Press the [Computer], [S-Video] or [Video] button on the remote control or the [Source Search] button on
the remote control or the projector's control panel to change the image. s page 18
Is the power for the computer or video
source turned on?
Turn the power on for the devices.
Are the image signals being output to the If the image signals are only being output to the computer's LCD monitor or to the accessory monitor,
you need to change the output to an external destination as well as the computer's own monitor. For some
projector?
computer models, when the image signals are output externally, they no longer appear on the LCD
Only when projecting images from
monitor or accessory monitor.
a laptop computer or computer
s Computer documentation, under a title such as "External output" or "Connecting an external
monitor"
with a built-in LCD screen
If the connection is made while the power is already turned on, the function [Fn] key that switches the
computer's video signal to external output may not work. Turn the power for the projector and the
computer off and then back on again.
50
Problems Solving
Images are fuzzy or out of focus
Check
Remedy
Has the focus been adjusted correctly?
Turn the focus ring on the projector to adjust the focus.
Is the lens cover still attached?
Remove the lens cover.
Is the projector at the correct distance?
The recommended projection distance for EMP-62 ranges from 86 cm to 1071 cm. When using EMP-82/
X3, the distance ranges from 87 cm to 1080 cm.
Is the keystone adjustment value too
large?
Decrease the projection angle to reduce the amount of keystone correction.
Has condensation formed on the lens?
If the projector is suddenly taken from a cold environment to a warm environment or if sudden ambient
temperature changes occur, condensation may form on the surface of the lens, and this may cause the
images to appear fuzzy. Set the projector up in the room approximately one hour before it is to be used. If
condensation forms on the lens, turn the power off and wait for the condensation to disappear.
Interference or distortion appear in images
Check
Are the image signal format settings
correct?
Remedy
If a composite videog or S-Videog source is connected to the projector, use the "Video Signal" menu
command to select the signal format. "Signal" - "Video Signal" s page 35
Only when projecting images
from a video source
Are the cables connected correctly?
Check that all of the cables required for projection are securely connected.
Is an extension cable being used?
If an extension cable is used, electrical interference may affect the signals. Use the accessory cables and
check if this helps.
Has the correct resolution been selected? Set the computer so that the signals that are output are compatible with this projector.
"List of Supported Monitor Displays" s page 72 s Computer documentation
Only when projecting computer images
Have the "Sync.g" and "Trackingg"
settings been adjusted correctly?
Computer and RGB video signals only
Press the [Auto] button on the remote control or the [Enter] button on the projector's control panel to
carry out automatic adjustment. If the images have not been adjusted correctly after using automatic
adjustment, you can make the adjustments using the "Sync." and "Tracking" functions. s page 13, 14
51
Problems Solving
Image is truncated (large) or small
Check
Remedy
Has the "Aspect ratiog" been set
correctly?
Press the [Resize] button on the remote control. s page 21
Is the image still being enlarged by the
E-Zoom function?
Press the [Esc] button on the remote control to cancel the E-Zoom function. s page 22
Has the "Position" setting been adjusted
correctly?
If analogue RGB images from a computer or RGB video images are being projected, press the [Auto]
button on the remote control or the [Enter] button on the projector's control panel to carry out automatic
adjustment.
If the images have not been correctly adjusted after using the automatic setup function, adjust the setting
manually using the "Position" menu command.
If signals other than analogue RGB images from a computer or RGB video images are being input, adjust
the setting manually using the "Position" menu command. "Signal" - "Position" s page 34
Has the computer been set for dual
display?
If dual display has been activated in the Display Properties of the computer's Control Panel, the projector
will only project about half of the image on the computer screen. To display the whole of the image on
the computer screen, turn off the dual display setting. s Computer video driver documentation
Only when projecting computer images
Has the correct resolution been selected? Set the computer so that the signals that are output are compatible with this projector.
"List of Supported Monitor Displays" s page 72 s Computer documentation
Only when projecting computer images
52
Problems Solving
Image colours are not right
Check
Remedy
Do the input signal settings match the
signals from the connected device?
If a composite videog or S-Videog source is connected to the projector, use the "Video Signal" menu
command to select the video signal format.
"Signal" - "Video Signal" s page 35
Has the image brightness been adjusted
correctly?
Use the "Brightness" menu command to adjust the brightness. "Image" - "Brightness" s page 33
Are the cables connected correctly?
Check that all of the cables required for projection are securely connected.
Has the image contrastg been adjusted
correctly?
Use the "Contrast" menu command to adjust the contrast. "Image" - "Contrast" s page 33
Has the colour been adjusted correctly?
Use the "Color Adjustment" menu command to adjust the colour. "Image" - "Color Adjustment"
s page 33
Have the colour saturation and tint been
adjusted correctly?
Use the "Color Saturation" and "Tint" menu commands to adjust the colour and tint. "Image" - "Color
Saturation", "Tint" s page 33
Only when projecting images
from a video source
Images appear dark
Check
Remedy
Have the image brightness and luminance Use the "Brightness" and "Brightness Control" menu commands to adjust the brightness and luminance.
"Image" - "Brightness" s page 33 "Settings" - "Brightness Control" s page 36
been adjusted correctly?
Has the image contrastg been adjusted
correctly?
Use the "Contrast" menu command to adjust the contrast. "Image" - "Contrast" s page 33
Is the lamp due for replacement?
When the lamp is nearly due for replacement, the images will become darker and the colour quality will
become poorer. When this happens, the lamp should be replaced with a new one. s page 59
53
Problems Solving
Nothing appears on the external monitor
Check
Remedy
Are images from a port other than the
The only images that can be displayed on an external monitor are those from the Computer port. You
Computer port being projected? (EMP-X3 cannot output video equipment images to an external monitor. s page 66
only)
Are images from a port other than the
Computer1 port being projected? (EMP82/62 only)
The only images that can be displayed on an external monitor are those from the Computer1 port. You
cannot output video equipment images to an external monitor. s page 66
Problems when projection starts
Power does not turn on
Check
Remedy
Have you pressed the [Power] button?
Press the [Power] button to turn the power on.
Are all of the indicators switched off?
The power cable is not connected correctly or power is not being supplied. Connect the power cable to
the projector correctly.
Alternatively, check the circuit breaker to see if power is being supplied.
Do the indicators turn off and on when the There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the
power cable. If this does not solve the problem, stop using the projector, disconnect the power cable from
power cable is touched?
the wall outlet and contact the nearest address provided in the "International Warranty Conditions"
section of the Safety Instructions/World-Wide Warranty Terms booklet.
Other problems
No sound can be heard or the sound is faint
Check
Remedy
Is the audio source connected correctly?
Check that the cable is connected to the Audio port.
Has the volume been adjusted to the
minimum setting?
Adjust the volume so that sound can be heard. s page 17
Is A/V Mute mode active?
Press the [A/V Mute] button on the remote control to cancel the A/V mute function. s page 20
54
Problems Solving
The remote control does not work
Check
Remedy
Is the remote control light-emitting area
facing towards the remote control lightreceiving area when it is operated?
Face the remote control towards the remote control light-receiving area.
The operating angle for the remote control is approximately ±30º horizontally and approximately ±15º
vertically.
Is the remote control too far from the
projector?
The operating range for the remote control is approximately 6m.
Is direct sunlight or strong light from
fluorescent lamps shining onto the
remote control light-receiving area?
Set the projector up in a location where strong light will not shine onto the remote control light-receiving
area.
Are the batteries dead, or have the
batteries been inserted correctly?
Insert new batteries, while making sure that they are inserted the correct way around. s page 58
Has a remote control button been pressed If any of the buttons on the remote control are pressed down for more than 30 seconds, the remote control
stops sending signals (remote control's sleep mode) . The purpose of this is to prevent the batteries from
for more than 30 seconds?
being consumed due to something being placed on top of the remote control.
When the button is released, normal remote control operation will resume.
Appendices
This chapter provides information on maintenance procedures to ensure the best level of performance from the
projector.
Installation........................................................... 56
Glossary............................................................... 68
• Setting Up the Projector .....................................................56
List of ESC/VP21 Commands............................. 70
Maintenance ........................................................ 57
• Command List .................................................................... 70
• Cable Layouts ..................................................................... 70
• Cleaning ...............................................................................57
•Cleaning the Projector's Surface................................................ 57
•Cleaning the Lens ...................................................................... 57
•Cleaning the Air Filters and Air Intake Vent ............................. 57
• Replacing Consumables......................................................58
•Replacing the batteries............................................................... 58
•Lamp Replacement Period......................................................... 59
•Replacing the Lamp................................................................... 59
•Resetting the Lamp Operating Time.......................................... 62
•Replacing the Air Filter ............................................................. 63
•USB connection..........................................................................70
•Serial connection (EMP-82/62 only)..........................................71
• USB Connection Setup ....................................................... 71
List of Supported Monitor Displays .................. 72
•Computer/RGB Video ................................................................72
•Component Video.......................................................................72
•Composite Video/S-Video..........................................................72
Specifications...................................................... 73
Saving a User's Logo ......................................... 64
Appearance.......................................................... 75
Connecting to External Output Equipment ...... 66
• EMP-X3 ............................................................................... 75
• EMP-82/62........................................................................... 76
• Connecting to an External Monitor...................................66
• Connecting to an external speaker (when using the EMP82/62)66
Optional Accessories and Consumables ......... 67
•Optional Accessories ................................................................. 67
•Consumables.............................................................................. 67
Index ..................................................................... 78
Installation
Setting Up the Projector
56
• Front/ceiling projection (Front/Ceiling projection)
The projector supports the following four different projection methods,
allowing you to choose the best method for displaying your images.
c Caution: • Before setting up the projector, make sure you read the
separate SafetyInstructions/World-Wide Warranty
Terms first.
• Do not set this projector up on its side to carry out
projection,otherwise malfunctions may occur.
• Front projection (Front projection)
• Rear/ceiling projection using a translucent screen
(Rear/Ceiling projection)
• Rear projection using a translucent screen (Rear projection)
* A special method of installation is required for suspending the projector
from a ceiling. Please contact your supplier if you would like to use this
installation method. The optional ceiling mount is required when
installing the projector on a ceiling. s page 67
Q Tip:
When using ceiling projection or projection using a
translucent screen, set the "Projection" command in the
"Extended" menu to match the installation method.
s page 37
Maintenance
This section describes maintenance tasks such as cleaning the projector and
replacing consumable parts.
Cleaning
You should clean the projector if it becomes dirty or if the quality of
projected images starts to deteriorate.
57
Cleaning the Air Filters and Air Intake Vent
If dust collects on the air filter or the air outlet, it can cause the internal
temperature of the projector to rise, and this can lead to problems with
operation and shortening of the optical engine's service life.
It is recommended that you clean these parts at least once every three
months. Clean them more often than this if using the projector in
particularly dusty environments.
c Caution: Make sure you read the separate Safety Instructions/
World-Wide Warranty Terms before cleaning.
Cleaning the Projector's Surface
Clean the projector's surface by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water
containing a small amount of neutral detergent, and then firmly wring the
cloth dry before using it to wipe the projector's surface. Then wipe it again
with a soft, dry cloth.
c Caution: Do not use volatile substances such as wax, alcohol or
thinner to clean the projector's surface. These can
cause the projector to warp and make the coating finish
peel off.
Cleaning the Lens
Use a commercially-available air blower, or use a lens cleaning paper to
gently wipe the lens.
c Caution: Do not rub the lens with harsh materials or subject the
lens to shocks, as it can easily become damaged.
Q Tip:
If the air filters are broken or if the warning message
reappears after they have been cleaned, they should be
replaced. Replace with a new air filter. See "Replacing
the Air Filter". s page 63
58
Maintenance
Replacing Consumables
This section explains how to replace the remote control batteries, the lamp,
and the air filters.
2 Insert the batteries.
A
Check the positions of the (+) and (–) marks inside the battery
holder to ensure that the batteries are inserted the correct way.
Replacing the batteries
If delays in the responsiveness of the remote control occur or if it does not
operate after it has been used for some time, it probably means that the
batteries are becoming flat. Replace the batteries. Have two spare
AAA-size alkali batteries ready to use when required.
c Caution: Make sure you read the Safety Instructions/World-Wide
Warranty Terms before handling the batteries.
PROCEDURE
1 Remove the battery cover.
A
While pushing the catch of the battery compartment cover, lift
the cover up.
Catch
3 Replace the battery cover.
A
Press the battery compartment cover until it clicks into place.
59
Maintenance
Lamp Replacement Period
Q Tip:
It is time to replace the lamp when:
• The message "Replace the Lamp." appears on the screen when
projection starts
.
A message will be displayed.
• When the Lamp indicator is flashing orange
Flashing orange
• The lamp replacement message is set to appear after the
following periods of time in order to maintain the initial
brightness and quality of the projected images.
"Brightness Control" s page 36
· When used continuously at high brightness: Approx.
1900 hours
· When used continuously at low brightness: Approx.
2900 hours
• If you continue to use the lamp after this period, the
possibility of the lamp breaking becomes greater. When
the lamp replacement message appears, replace the
lamp with a new one as soon as possible, even if it is still
working.
• Depending on the characteristics of the lamp and on
the way it has been used, the lamp may become darker
or stop working before the lamp warning message
appears. You should always have a spare lamp ready in
case it is needed.
• Contact your dealer for a spare lamp.
Replacing the Lamp
• The projected image gets darker or starts to deteriorate
c Caution: • If you are replacing the lamp because it has stopped
working, it is possible that the lamp is broken.
If replacing the lamp of a projector which has been
installed on a ceiling, you should always assume that
the lamp is broken and be extremely careful when
removing the lamp cover.
• Wait until the lamp has cooled down sufficiently before
removing the lamp cover. To give the lamp enough time
to cool down after turning off the power, wait for about
one hour.
60
Maintenance
PROCEDURE
A
1
After you turn off the projector’s power, and the
confirmation buzzer beeps twice, disconnect the
power cable.
3 Loosen the two lamp fixing screws.
A
Loosen the two lamp fixing screws with the screwdriver that is
supplied with the spare lamp (or your own cross head
screwdriver).
2 Wait until the lamp has cooled down, then remove the
A
lamp cover from the base of the projector.
Loosen the lamp cover fixing screw with the screwdriver that is
supplied with the spare lamp (or your own cross head
screwdriver).
Then slide the lamp cover straight forward and lift it to remove.
4 Take out the lamp.
A
Hold the lamp as shown in the illustration below and lift it up
and out of the projector.
If the lamp is broken replace it with a new lamp, or contact your
local dealer for further advice. If replacing the lamp yourself,
be careful to avoid pieces of broken glass.
Maintenance
1 Install the new lamp.
A
Insert the new lamp so that the lamp fits in place correctly and
once it is fully inserted, tighten the two screws.
2 Install the lamp cover.
A
Slide the lamp cover and tighten the cover fixing screws.
Q Tip:
• Install the lamp securely. If the lamp cover is removed,
the lamp turns off automatically as a safety precaution.
Moreover, the lamp will not turn on if the lamp or the
lamp cover is not installed correctly.
• This product includes a lamp component that contains
mercury (Hg). Please consult your state and local
regurations regarding disposal or recycling. Do not put
in the trash.
61
62
Maintenance
Resetting the Lamp Operating Time
The projector has a built-in counter which keeps track of the lamp
operating time. When the cumulative operating time reaches a certain
point, it causes the replacement warning message to be displayed.
Therefore, the counter needs to be reset after the lamp has been replaced
with a new one. You can do this using the configuration menu.
2 Select "Reset" from the configuration menu, and then
A
select "Reset Lamp Hours".
For details on this operation, refer to "Using the Configuration
Menu". s page 32
Check the buttons you can use, and the operations they
perform, in the guide at the bottom of the screen.
Using the remote control
Q Tip:
Using the control panel
Do not reset the lamp operating time except after the
lamp has been replaced, otherwise the lamp replacement
period will not be indicated correctly.
PROCEDURE
1 Connect the power cable and turn on the projector.
A
3 When "Execute?" appears, select "Yes".
A
The lamp operating time will then be reset.
63
Maintenance
Replacing the Air Filter
If the air filters are broken or if the warning message reappears after they
have been cleaned, they should be replaced.
The air filter can be replaced even if the projector is installed on a ceiling.
3 Install the new air filter.
A
Slide the air filter covers in from the outside and push them in
until they click into place.
PROCEDURE
1 After you turn off the projector’s power, and the
A
confirmation buzzer beeps twice, disconnect the
power cable.
2 Remove the air filter.
A
Put your finger into the recess of the air filter and slide it
forward to remove it.
Recess
Q Tip:
Dispose of used air filters properly in accordance with
your local regulations.
Air filter frame: Polycarbonate, ABS plastic
Filter: Polyurethane foam
Saving a User's Logo
You can record the image that is currently being projected as a user's logo.
Q Tip:
When a user's logo is recorded, the previous user's logo
will be erased.
PROCEDURE
64
2 Select "Extended" from the configuration menu, and
A
then select "User’s Logo".
For details on this operation, refer to "Using the Configuration
Menu". s page 32
Check which buttons on the remote control or the control panel
you can use, and the operations they perform, in the guide at the
bottom of the screen.
1 Project the image you would like to use as the user’s
A
logo, and then display the configuration menu.
Using the remote control
Using the control panel
Q Tip:
• If the "User’s Logo Protect" function of "Password
Protect" is set to "On", a message is displayed and the
user's logo can not be recorded. To record a user's logo,
set "User’s Logo Protect" to "Off" first. s page 28
• If keystone correction, E-Zoom and so on, have been
carried out, the function currently being performed is
cancelled when the "User’s Logo" menu is selected.
65
Saving a User's Logo
3 When "Choose this image as the User's Logo?"
A
appears, select "Yes".
Q Tip:
When you press the [Enter] button on either the remote
control or the projector's control panel, the image signal
will be displayed at their original resolution, so if a
signal with a resolution that is different from the panel
resolution of the projector is projected, or if a video
image is being projected, the display size will change.
Q Tip:
User's logos can be saved at up to 400 × 300 dots in size.
5 When "Select this image?" appears, select "Yes".
A
6 Select the zoom rate from the Zoom rate setting
A
screen.
4 The image to be recorded and a selection marquee
A
box will be displayed. Move the marquee box to select
the part of the image to use.
7 When "Save this image?" is displayed, select "Yes".
A
The image will then be saved. Once the image has been saved,
the message "Completed." will be displayed.
Q Tip:
Using the remote control
Using the control panel
• Saving the user's logo may take a few moments (about
15 seconds). Do not use the projector or any other
sources which are connected to the projector while the
user's logo is being saved, otherwise it may result in
errors in projector operation.
• Once a user's logo has been saved, the logo setting
cannot be returned to the factory default.
Connecting to External Output Equipment
Connecting to an External Monitor
Analogue RGB images and RGB video images from a computer that are
being input to the Computer/Computer1 port can be viewed on an external
computer monitor at the same time they are being projected by the
projector, so that the images can be checked at times such as when giving
presentations.
If the images being projected are from a source that is connected to the
Computer2 port, these images cannot be output to an external monitor.
Connect the external monitor using the cable that is provided with the
monitor.
66
Connecting to an external speaker (when using the
EMP-82/62)
You can connect speakers with built-in amplifiers to the projector's Audio
Out port in order to enjoy a fuller quality of sound.
Use a commercially-available audio cable with pin jack ⇔ stereo mini jack
(3.5 mm) plugs or similar.
Use an audio cable with plugs that match the ports for the external audio
equipment.
To external audio equipment
Monitor port
To Audio Out port
Cable provided with monitor
Q Tip:
Audio cable
(commercially available)
To Monitor Out port (black)
• Component video, S-Video, and composite video images
cannot be output to an external monitor.
• The setting gauge for keystone correction and the
configuration menus and help menus are not output to
the external monitor.
Q Tip:
When a stereo mini-jack audio cable is inserted into the
Audio Out port, the sound will be output to external
speakers. No sound will be output from the projector's
built-in speaker at this time.
Optional Accessories and Consumables
67
The following optional accessories are available for purchase if required. This list of optional accessories is current as of September, 2005. Details of accessories
are subject to change without notice. Varies depending on country of purchase.
Optional Accessories
Soft carrying case ELPKS16
Use this case if you need to carry the projector by hand.
60" screen ELPSC07
80" screen ELPSC08
100" screen ELPSC10
Portable roll-type screens. (Aspect ratiog 4:3)
50" portable screen ELPSC06
A compact screen which can be carried easily. (Aspect ratio 4:3)
VGA-HD15 PC cable ELPKC02
(1.8 m (6 ft.) - for mini D-Sub 15-pin/mini D-Sub 15-pin)
This is the same as the computer cable supplied with the projector.
VGA-HD15 PC cable ELPKC09
(3 m (9.8 ft.) - for mini D-Sub 15-pin/mini D-Sub 15-pin)
VGA-HD15 PC cable ELPKC10
(20 m (65.6 ft.) - for mini D-Sub 15-pin/mini D-Sub 15-pin)
Use one of these longer cables if the computer cable supplied with the
projector is too short.
Component video cable ELPKC19
(3 m (9.8 ft.) - for mini D-Sub 15-pin/RCA male × 3)
Use to connect a component videog source.
Ceiling mount * ELPMB18
Use when installing the projector on a ceiling.
Ceiling plate* ELPFC03
Pipe 370 (370 mm (14.57 in.)/silver)* ELPFP04
Pipe 570 (570 mm (22.44 in.)/silver)* ELPFP05
Pipe 770 (770 mm (30.31 in.)/silver)* ELPFP06
Use when installing the projector on a high ceiling or a ceiling with
veneer panels.
* A special method of installation is required in order to suspend the
projector from a ceiling. Please contact your dealer if you would like to
use this installation method.
Consumables
Spare lamp ELPLP34
Use as a replacement for used lamps.
Filter kit ELPAF08
(2 air filters)
Use as a replacement for used air filters.
Glossary
68
The following is an explanation of some of the terms used in this guide which may be unfamiliar or which are not explained in the text of this guide itself. Further
information can be obtained by referring to other commercially-available publications.
Aspect ratio
Color Temp.
Component video
Composite video
Contrast
Dolby Digital
HDTV
Interlaced
Progressive
Refresh rate
SDTV
The ratio between an image's length and its height. HDTV images have an aspect ratio of 16:9 and appear elongated. The
aspect ratio for standard images is 4:3.
The temperature of an object that is emitting light. If the colour temperature is high, the colours take on a bluish tinge. If the
colour temperature is lower, the colours take on a reddish tinge.
Video signals which have the video brightness signals and colour signals separated, in order to provide better image quality.
In high-definition TV (HDTV), it refers to images which consist of three independent signals: Y (luminance signal), and Pb
and Pr (colour difference signals).
Video signals which have the video brightness signals and colour signals mixed together. The type of signals commonly used
by household video equipment (NTSC, PAL and SECAM formats).
The carrier signal Y (luminance signal) and chroma (colour) signal which are contained in the colour bar are overlapped to
form a single signal.
The relative brightness of the light and dark areas of an image can be increased or decreased in order to make text and
graphics stand out more clearly, or to make them appear softer. Adjusting this particular property of an image is called
"contrast adjustment".
A sound format developed by Dolby Laboratories. Normal stereo is a 2-channel format which uses two speakers. Dolby
Digital is a 6-channel (5.1-channel) system which adds to this a centre speaker two rear speakers and a sub-woofer.
An abbreviation for High-Definition Television. It refers to high-definition systems which satisfy the following conditions.
•Vertical resolution of 750p or 1125i or greater (p = progressiveg, i = interlacedg)
•Screen aspect ratiog of 16:9
•Dolby Digitalg audio reception and playback (or output)
A method of image scanning whereby the image data is divided into fine horizontal lines which are displayed in sequence
starting from left to right and then from the top to the bottom of the screen. The even-numbered lines and odd-numbered lines
are displayed alternately.
A method of image scanning whereby the image data from a single image is scanned sequentially from top to bottom to create
a single image.
The light-emitting element of a display maintains the same luminosity and colour for an extremely short time. Because of this,
the image must be scanned many times per second in order to refresh the light-emitting element. The number of refresh
operations per second is called the "refresh rate", and is expressed in hertz (Hz).
An abbreviation for Standard Definition Television. It refers to standard television systems which do not satisfy the conditions
for High-Definition Television.
Glossary
Security lock
Squeeze mode
sRGB
SVGA
S-Video
SXGA
Sync (synchronisation)
Tracking
USB
VGA
XGA
69
A device consisting of a projector case with a hole in it that a commercially-available theft-prevention cable can be passed
through in order to secure the device to a table or pillar. This projector is compatible with the Microsaver Security System
manufactured by Kensington.
In this mode, wide-screen images in 16:9 mode are compressed in the horizontal direction so that they are stored on the
recording medium as 4:3 images.
When these images are played back by the projector in squeeze mode, they are restored to their original 16:9 format.
An international standard for colour intervals that was formulated so that colours which are reproduced by video equipment
can be handled easily by computer operating systems (OS) and the Internet. If the connected source has a sRGB mode, set
both the projector and the connected signal source to sRGB.
A type of video signal with a resolution of 800 (horizontal) × 600 (vertical) dots which is used by IBM PC/AT-compatible
computers.
A video signal which has the luminance component and colour component separated in order to provide better image quality.
It refers to images which consist of two independent signals: Y (luminance signal), and C (colour signal).
A type of video signal with a resolution of 1280 (horizontal) × 1024 (vertical) dots which is used by IBM PC/AT-compatible
computers.
The signals output from computers and RGB video equipment have a specific frequency. If the projector frequency does not
match this frequency, the resulting images will not be of a good quality. The process of matching the phases of these signals
(the relative position of the crests and troughs in the signal) is called "synchronisation". If the signals are not synchronized,
problems such as flickering, blurriness and horizontal interference can occur.
The signals output from computers and RGB video equipment have a specific frequency. If the projector frequency does not
match this frequency, the resulting images will not be of a good quality. The process of matching the frequency of these
signals (the number of crests in the signal) is called "tracking". If tracking is not carried out correctly, wide vertical stripes will
appear in the projected images.
An abbreviation for Universal Serial Bus. USB is an interface for connecting personal computers to peripheral devices which
only support relatively low data transmission speeds.
A type of video signal with a resolution of 640 (horizontal) × 480 (vertical) dots which is used by IBM PC/AT-compatible
computers.
A type of video signal with a resolution of 1024 (horizontal) × 768 (vertical) dots which is used by IBM PC/AT-compatible
computers.
List of ESC/VP21 Commands
Command List
Cable Layouts
When a power on command is sent to the projector, the power will turn on
and the projector will change to warm-up mode. When the power has
turned on, a colon ":" (3Ah) will be returned.
When the projector executes a command, it returns a ":" and waits for the
next command to be sent.
If command processing terminates with an error, the projector outputs an
error message and then returns the ":" code.
Item
ON
Power ON/OFF
OFF
Computer (Auto)
Computer
Signal selection
Component Video
Video
S-Video
ON
A/V Mute ON/OFF
OFF
Black
A/V Mute Selection
Blue
User’s Logo
Item
Signal selection
70
Computer (Auto)
Computer
Component Video
Command
PWR ON
PWR OFF
SOURCE 1F
SOURCE 11
SOURCE 14
SOURCE 41
SOURCE 42
MUTE ON
MUTE OFF
MSEL 00
MSEL 01
MSEL 02
Command
Computer1
Computer2
port
port
SOURCE 1F
SOURCE 2F
SOURCE 11
SOURCE 21
SOURCE 14
SOURCE 24
* When issuing any of the above commands, tack a Carriage Return (CR)
code (0Dh) on to the end.
USB connection
Connector shape: USB (type B)
<At the projector>
(type B)
<At the computer>
71
List of ESC/VP21 Commands
USB Connection Setup
Serial connection (EMP-82/62 only)
• Connector
• Projector
shape
input connector
In order to control the projector using ESC/VP21 commands via a USB
connection, the following preparations must be carried out.
: D-Sub 9 pin (male)
: Control (RS-232C)
<At projector>
<At computer>
PROCEDURE
1 Download the USB driver (USB-COM Driver) from the
A
EPSON website to your computer.
The URL is as follows.
http://esupport.epson-europe.com/downloads/en/
2 Install the downloaded USB driver onto your
A
computer.
Read the instructions displayed on the download screen.
3 <Using EMP-X3>
A
Set "Link21L" to "On" in the "Extended" menu.
<At projector> (PC serial cable)
GND 5
RD
2
TD
3
DTR 4
DSR 6
<At computer>
5
GND
3
TD
2
RD
6
DSR
4
DTR
Signal
Function
GND
TD
RD
DSR
DTR
Signal wire ground
Transmit data
Receive data
Data set ready
Data terminal ready
<Using EMP-82/62>
Select "USB" for "COM port" in the "Extended" menu.
4 Turn the projector's power off.
A
5 Turn off this projector after the confirmation buzzer
A
beeps twice.
Once the projector's power has turned back on, communication
via a USB Connection will then be possible.
If you disconnect the power cable before the
c Caution: confirmation buzzer beeps twice, the communication
port is not changed.
List of Supported Monitor Displays
Computer/RGB Video
Signal
VGAg
VGAEGA
VESA
SVGAg
XGAg
SXGAg
SXGA
SXGA
UXGA
MAC13"
MAC16"
MAC19"
MAC19"
MAC21"
SDTVg(625i)
SDTV(525i)
SDTV(525p)
HDTVg(750p)
HDTV(1125i)
Component Video
Refresh rateg
(Hz)
Resolution
(dots)
60
640× 480
640× 350
640× 480
Resolutions for
resize display
(dots)
EMPEMP-62
X3/82
1024× 768 800× 600
1024× 560 800× 438
1024× 768 800× 600
800× 600
1024× 768
800× 600
1024× 768
1152× 864
1280× 960
1280× 1024
1600× 1200
640× 480
832× 624
1024× 768
1024× 768
1152× 870
720× 576
720× 480
640× 480
1280× 720
1920× 1080
1024× 768
1024× 768
1024× 768
960× 768
1024× 768
1024× 768
1024× 768
1024× 768
1024× 768
1016× 768
1024× 768
1024× 768
1024× 768
1024× 576
1024× 576
800× 600
800× 600
800× 600
750× 600
800× 600
800× 600
800× 600
800× 600
794× 600
800× 600
800× 600
800× 600
800× 450
800× 450
60/72/75/85,iMac*
56/60/72/75/
85,iMac*
60/70/75/85,iMac*
70/75/85
60/75/85
60/75/85
60
60
50
60
60
60
60
72
* Connection is not possible if the equipment does not have a VGA output
port.
The projection of some signals not listed in the table may still be possible.
However, not all functions may be supported.
Signal
SDTVg(525i)
(D1)
SDTV (625i)
SDTV (525p)
(D2)
HDTVg(750p)
16:9 (D4)
HDTV (1125i)
16:9 (D3)
Refresh
rateg (Hz)
Resolutions (dots)
EMP-X3/82
EMP-62
Aspect Aspect Aspect Aspect
ratiog
ratio
ratio
ratio
4:3
16:9
4:3
16:9
60
1024× 768 1024× 576 800× 600 800× 450
50
1024× 768 1024× 576 800× 600 800× 450
60
1024× 768 1024× 576 800× 600 800× 450
60
1024× 768 1024× 576 800× 600 800× 450
60
1024× 768 1024× 576 800× 600 800× 450
Composite Video/S-Video
Signal
TV (NTSC)
TV (PAL,
SECAM)
60
Resolutions (dots)
EMP-X3/82
EMP-62
Aspect Aspect Aspect Aspect
ratiog
ratio
ratio
ratio
4:3
16:9
4:3
16:9
1024× 768 1024× 576 800× 600 800× 450
50
1024× 768 1024× 576 800× 600 800× 450
Refresh
rateg (Hz)
Specifications
Product name
Dimensions
Panel size
Display method
Resolution
Focus adjustment
Zoom adjustment
Lamp (light source)
Max. audio output
Speaker
Power supply
Operating altitude
Operating temperature
Storage temperature
Weight
Connectors Computer/
Computer 1
Audio Input
Computer 2
Audio Input
S-Video
Audio Input
Video
Audio Input
USB*
RS-232C
Monitor Out
Audio Out
1
1
1
1
1
1
1
1
1
1
1
1
73
EMP-X3
EMP-82
EMP-62
327 (W) × 86 (H) × 246 (D) mm (not including feet and speaker)
0.6 inches
Polysilicon TFT active matrix
XGAg 786,432 pixels
SVGAg 480,000
(1,024 (W) × 768 (H) dots) × 3
pixels (800 (W) ×
600 (H) dots) × 3
Manual
Manual (approx. 1:1.2)
UHE lamp, 170 W, Model No.: ELPLP34
1W monaural
5W monaural
1
100-240VAC 50/60Hz 2.9-1.2A
Power Consumption
Operating: 240W(100 to 240 V area)
Standby: 5.0W(100 to 240 V area)
0 - 2280 m (0 - 7500 ft)
+5 – +35ºC (No condensation)
-10 – +60ºC (No condensation)
Approx. 2.6 kg
Approx. 2.7 kg
Mini D-Sub 15-pin
(female) Blue
RCA pin jack
Stereo mini jack
Mini D-Sub 15-pin (female) Blue
Stereo mini jack
Mini DIN 4-pin
RCA pin jack
RCA pin jack
RCA pin jack
USB connector (B series)
D-Sub 9-pin (male)
Mini D-Sub 15-pin (female) Black
Stereo mini jack
Pixelworks DNXTM ICs are used
in this Projector.
Angle of tilt
0°- 30°
0°- 30°
0°- 30°
0°- 30°
If you use it when it is tilted more than 30°, it
could be damaged and cause an accident.
* The USB interface complies with the USB 1.1
standard.
The USB connector is not guaranteed to operate
correctly with all USB-compatible devices.
74
Specifications
Safety
EMC
USA
UL60950 3rd Edition
Canada
CSA C22.2 No.60950
European Community
The Low Voltage Directive
(73/23/EEC)
IEC60950 3rd Edition
USA
FCC Part 15B Class B (DoC)
Canada
ICES-003 Class B
European Community
The EMC Directive
(89/336/EEC)
EN55022 Class B
EN55024
IEC/EN61000-3-2
IEC/EN61000-3-3
Australia/New Zealand
AS/NZS CISPR 22:2002 Class B
Appearance
75
EMP-X3
3-M4× 9
Centre of lens
80
86
50.1*
246
12
12
83.7
7.7
327
104.7
69.7
127
115
*Distance from center of lens to suspension bracket fixing point
Units: mm
76
Appearance
EMP-82/62
3-M4× 9
Centre of lens
80
86
50.1*
246
12
12
83.7
7.7
327
104.7
69.7
127
115
*Distance from center of lens to suspension bracket fixing point
Units: mm
Index
A
Air exhaust vent............................. 6
Air filter ....................................... 10
Air intake vent ............................. 10
Angle of tilt.................................. 73
Aspect ratio.................................. 21
Audio Out port............................... 9
Audio port................................... 8, 9
Auto Keystone ............................. 36
Auto Setup .............................. 13, 34
A/V Mute..................................... 20
77
Computer1 port ..............................9
Computer2 Input ..........................34
Computer2 port ..............................9
Computer Input ............................34
Computer port ................................8
Configuration Menu .....................32
Connectors......................................8
Consumables ................................67
Contrast ........................................33
Control Panel..................................7
Cross.............................................23
G
D
"Image" Menu.............................. 33
Indicator....................................... 44
"Info" Menu ................................. 39
Input Signal.................................. 39
B
Blackboard................................... 15
Brightness .................................... 33
Brightness Control....................... 36
Direct Power On...........................38
Display .........................................37
Display Background.....................37
E
C
Cleaning the Air Filter................. 57
Cleaning the Lens ........................ 57
Cleaning the Projector Surface .... 57
Color Adjustment ........................ 33
Color Mode............................. 15, 33
Color Saturation........................... 33
Color Temp.................................. 33
COM Port .................................... 38
Computer1 Input.......................... 34
ESC/VP21 ....................................70
"Extended" Menu .........................37
E-Zoom ........................................22
F
Focus ring.......................................6
Freeze ...........................................20
Front adjustable foot ......................6
Game............................................ 15
Glossary ....................................... 68
H
HDTV .......................................... 72
Help function ............................... 42
High Altitude Mode ..................... 38
Link 21L .......................................38
Low...............................................36
M
Menu.............................................32
Message ........................................37
Monitor Out port ........................ 8, 9
Mouse pointer...............................24
N
I
Numeric buttons ...........................11
O
Keystone ...................................... 36
Operating temperature..................73
Operation ......................................38
Operation Lock....................... 29, 36
Optional accessories .....................67
Overheating ..................................45
L
P
Lamp cover .................................... 6
Lamp Hours ................................. 39
Lamp indicator............................. 44
Lamp replacement period ............ 59
Language...................................... 38
Lens cover...................................... 6
Part Names and Functions..............6
Password Protect ..........................26
Password Protect stickers .............27
Photo.............................................15
Pointer ..........................................21
Pointer Shape................................36
K
78
Index
Port ................................................ 9
Position ................................... 13, 34
Power indicator............................ 44
Power inlet.................................. 8, 9
Power On Protect......................... 26
Presentation ................................. 15
Problem Solving .......................... 44
Progressive .................................. 34
Projection..................................... 37
R
Rear adjustable foot .................... 8, 9
Refresh Rate ................................ 39
Remote Control ...................... 11, 23
Remote control light-emitting area..
11
Remote control light-receiving area
6, ............................................... 8, 9
Replacing the Air Filter ............... 63
Replacing the batteries ................ 58
Replacing the Lamp..................... 59
Request Code............................... 26
Reset All ...................................... 40
Reset Lamp Hours .................. 40, 62
"Reset" Menu............................... 40
Resized display ............................ 72
Resolution............................... 39, 72
RS-232C port................................. 9
S
Search...........................................11
Security lock...................................6
"Settings" Menu ...........................36
Setting Up the Projector ...............56
Sharpness......................................33
"Signal" Menu ..............................34
Sleep Mode...................................38
Source...........................................39
Source Search........................... 7, 18
Speaker....................................... 8, 9
Specifications ...............................73
Sports............................................15
Squeeze mode...............................21
sRGB ............................................15
Standby Mode ..............................38
Startup Screen ..............................37
Storage temperature .....................73
Sub menu......................................32
Supported Monitor Displays ........72
Suspension bracket fixing point .. 10,
75
S-Video port ............................... 8, 9
Sync........................................ 14, 34
Sync. Info .....................................39
T
Temp indicator .............................44
Theatre ......................................... 15
Tint............................................... 33
Top menu ..................................... 32
Tracking..................................13, 34
Translucent screen ....................... 56
U
USB connection ........................... 71
USB port .....................................8, 9
User’s Logo ................................. 64
User’s Logo Protect ..................... 27
V
Video port ...................................8, 9
Video Signal ...........................35, 39
Volume ...................................17, 36
W
Wide-screen Projection................ 21
Wireless Mouse ........................... 23
Z
Zoom ring ...................................... 6
79
All rights reserved. No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise, without
the prior written permission of SEIKO EPSON CORPORATION. No
patent liability is assumed with respect to the use of the information
contained herein. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable
to the purchaser of this product or third parties for damages, losses,
costs, or expenses incurred by the purchaser or third parties as a result
of: accident, misuse, or abuse of this product or unauthorized
modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with SEIKO EPSON CORPORATION’s
operating and maintenance instructions.
General Notice:
EPSON is a registered trademark of SEIKO EPSON CORPORATION.
Macintosh, Mac and iMac are registered trademarks of Apple
Computer, Inc.
IBM is a registered trademark of International Business Machines
Corporation.
Windows, Windows NT and VGA are trademarks or registered
trademarks of Microsoft Corporation in the United States of America.
Dolby is a trademark of Dolby Laboratories.
Pixelworks and DNX are trademarks of Pixelworks, Inc.
Other product names used herein are also for identification purposes
only and may be trademarks of their respective owners. EPSON
disclaims any and all rights in those marks.
This product uses open source software.
SEIKO EPSON CORPORATION shall not be liable against any
damages or problems arising from the use of any options or any
consumable products other than those designated as Original EPSON
Products or EPSON Approved Products by SEIKO EPSON
CORPORATION.
SEIKO EPSON CORPORATION 2005. All rights reserved.