Emerson CF943 Owner`s manual

BP7335 Palazzo
1/9/07
9:05 AM
Page 1
READ AND SAVE THESE INSTRUCTIONS
PALAZZO™
54” Ceiling Fan
Owner's Manual
Model No.
CF943AGW00
CF943BZH00
Net Weight:
Part No. F40BP73350000
37.9
Lbs.
Form No. BP7335
ETL Model No.: CF943
BP7335 Palazzo
1/9/07
9:05 AM
Page 2
!
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these
instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service
panel disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a
warning device, such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan.
Always turn off the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before
wiring, and do not operate fan without blades.
2. The installation is to be in accordance with the National Electrical Code, ANSI/NFPA
70-1999 and Local Codes. Use the National Electrical Code if Local Codes do not
exist. The ceiling fan must be grounded as a precaution against possible electrical
shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably
supporting at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 50 Lbs. or Less”, and use the mounting screws provided with the
outlet box. Most outlet boxes commonly used for support of light fixtures are not
acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The downrod furnished with the fan provides the minimum recommended floor to
fan blade clearance for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent
accidental contact with the fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling
fan. If you do not know enough about electrical wiring, have your fan installed by a
licensed electrician.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used
with fan speed control Model No. SW105, manufactured by Rhine Electric Co., Ltd.
WARNING: This product is designed to use only those parts supplied with this
product and/or any accessories designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or accessories not designated for use with
this product by Emerson Electric Co. could result in personal injury or
property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when
installing the blade flanges, balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING: To reduce the risk of electric shock, this fan must be installed with an
isolating wall control/switch.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
2
BP7335 Palazzo
1/9/07
9:05 AM
Page 3
This Manual is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
Installed Wire Length
Up to 50 ft.
50-100 ft.
One Phillips head screwdriver
One wire stripper
One stepladder
Two 60-watt candelabra base bulbs
(not supplied)
!
Materials
Wire Size A.W.G.
14
12
WARNING
Before assembling your ceiling fan, refer
to the section on proper method of wiring
your fan (Page 11). If you feel you do not
have enough wiring knowledge or
experience, have your fan installed by a
licensed electrician.
Wiring, outlet box and box connectors
must be of type required by the local code.
The minimum wire would be a 3-conductor
(2-wire with ground) of the following sizes:
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each
step is completed, place a check mark in the box. This will insure that all steps
have been completed and will be helpful in finding your place should you be
interrupted.
!
a.
b.
c.
d.
e.
f.
g.
h.
i.
j.
Fan motor assembly
One coupling cover
One ceiling cover
Five fan blades
Five blade flanges
One light kit assembly
One hanger bracket
One hanger ball/6” downrod assembly
One glass shade
One fan/light wall control
(transmitter and receiver)
k. One loose parts bag containing:
1. One clevis pin
2. One hairpin clip
3. Five wire connectors
4. Two #8-32 x 1-1/4” threaded studs
(ceiling cover)
5. Two #8 external tooth lockwashers
(ceiling cover)
6. Two #8-32 knurled knobs
(ceiling cover)
7. Sixteen #10-32 x 5/16” pan head
blade screws
8. Sixteen #10 flat blade washers
9. Eleven #8-32 x 1-1/4” oval head
screws
10. Four #8-32 x 1/4” pan head screws
(light kit assembly)
WARNING
Do not install or use fan if any part is
damaged or missing. Call Toll-Free:
1-800-654-3545
!
WARNING
This product is designed to use only
those parts supplied with this product
and/or any accessories designated
specifically for use with this product by
Emerson Electric Co. Substitution of
parts or accessories not designated for
use with this product by Emerson Electric
Co. could result in personal injury or
property damage.
1. Open carton containing fan. Remove
top half of styrofoam unit. Remove
parts and check to see that you have
received the following parts:
NOTE: If you are uncertain of part
description, refer to exploded view
illustration.
3
BP7335 Palazzo
1/9/07
9:05 AM
Page 4
A. FAN MOTOR ASSEMBLY
B. COUPLING COVER
D. FAN BLADES
C. CEILING COVER
E. BLADE FLANGES
F. LIGHT FITTER
ASSEMBLY
G. HANGER BRACKET
H. HANGER BALL/
6" DOWNROD
ASSEMBLY
I. GLASS SHADE
J. FAN/LIGHT WALL CONTROL
K. LOOSE
PARTS BAG
HI
LIGHT
MED
LOW
FAN OFF
EMERSON®
OFF
NOTE: Place the parts from the loose
parts bags in a small container to keep
them from being lost.
ON
PROTECTIVE
PLASTIC BAG
2. Remove and discard the two cardboard
shipping retainers securing the motor
hub in the motor housing assembly.
3. Remove the fan motor assembly from
the protective plastic bag. Place all
carton contents on a protective surface.
IMPORTANT
IMPORTANT
CARDBOARD
SHIPPING RETAINER (2)
4
BP7335 Palazzo
1/9/07
9:05 AM
Page 5
Electrical Requirements
Ceiling Fan Procedures
IMPORTANT: Your ceiling fan will not
function properly, and may be
damaged, if used with any wall dimmer
switch or control other than the
Emerson Electric Fan/Light Wall
Control supplied with the fan, or an
optional Emerson Electric SW110
Remote Control.
General
Your Emerson ceiling fan comes supplied
with a Fan/Light Wall Control which
consists of a SW113 wall control
(transmitter) and a SW105 remote control
receiver mounted under the ceiling cover.
This system allows you to regulate your
ceiling fan speed and light intensity.
Your new ceiling fan will require a
grounded electrical supply line of 120 volts
AC, 60 Hz, 15 amp circuit.
NOTE: An optional Emerson Electric
SW110 Remote Control may also be
used to control your ceiling fan.
The outlet box must be securely anchored
and capable of withstanding a load of at
least 50 pounds.
Setting Operating
Frequency of Wall Control
and Receiver (Figure 1)
Your wall control and receiver have code
switches which must be set in one of 16
possible code combinations. The four
levers (numbered 1, 2, 3, and 4) on the
switches are factory-set in the ON (up)
position. Change the switch settings as
follows:
1. Slide the four switch levers in the wall
control to your choice of ON (up) or
down positions. Use a ball-point pen or
small screwdriver and slide the levers
firmly up or down.
2. In the receiver, slide the four switch
levers to the same positions as set in
the wall control. Make sure the levers
on both switches are in the same
positions, otherwise the fan will not
operate.
WARNING
To reduce the risk of fire, electric shock,
or personal injury, mount fan to outlet box
marked “Acceptable for Fan Support of
50 Lbs. or Less”, and use screws
supplied with outlet box. Most outlet
boxes commonly used for support of light
fixtures are not acceptable for fan
support and may need to be replaced.
Consult a qualified electrician if in doubt.
If your fan is to replace an existing ceiling
light fixture, turn electricity off at the main
fuse or circuit breaker box at this time and
remove the existing light fixture.
WARNING
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
CODE
SWITCH
SW105 RECEIVER
WALL CONTROL
LEVERS
2
3
!
1
!
4
ON
ON
1
2
3
4
RECEIVER SWITCH
LEVERS
SW113 WALL
CONTROL
Figure 1
5
CODE
SWITCH
BP7335 Palazzo
1/9/07
9:05 AM
Page 6
Installation of Wall Control
5. Connect the other black wire of wall
control to the “load” (black) wire in wall
box. Securely connect wires with wire
connector supplied.
6. Screw wall control into wall box and
install decorator style faceplate
(included). Leave wall control in “OFF”
mode until fan installation is completed.
7. Refer to page 7 to complete the ceiling
fan installation.
SINGLE-POLE
INSTALLATION (Figure 2)
HOT
FAN/LIGHT
WALL CONTROL
BLK
HI
LIGHT
MED
LOW
FAN OFF
EMERSON®
OFF
BLACK
ON
LOAD
BLACK
NEUTRAL
GROUND
REMOTE CONTROL
RECEIVER LOCATED
WITHIN THE CEILING
COVER
K
BL
HOT
TO
120V
AC SOURCE
TO
LOAD
HI
LIGHT
MED
LOW
Figure 2
FAN OFF
WARNING
OU
ND
FAN/LIGHT
WALL
CONTROL
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
WALL
BOX
Figure 3
3-WAY INSTALLATION
(On fan controlled by two different wall
controls) (See Figures 4 and 5.)
1. Disconnect power at circuit breaker or
remove fuse.
2. At all wall box locations remove
faceplates and screws from existing
switches. Pull switches out from wall
boxes and determine which wall box
contains the “hot” lead and which wall
box contains the “load” wire. Also,
identify traveler wires which are
common to both wall boxes.
Disconnect wires from existing
switches only. Do not attempt to
disconnect any wires not already
connected to existing switches.
3. Before installing wall control, place wall
control in “OFF” mode by pushing
“ON/OFF” switch to the “OFF” position.
1. Disconnect power at circuit breaker or
remove fuse.
2. Remove faceplate and screws from
existing wall switch. Pull switch out
from the wall box. Determine the “hot”
wire and the “load” wire and disconnect
these wires from switch. Do not attempt
to disconnect any wires not already
connected to existing switch.
3. Before installing wall control, place wall
control in “OFF” mode by pushing
“ON/OFF” switch to the “OFF” position.
!
BL
ON
GR
!
OFF
K
AC
EMERSON ®
WARNING
Do not connect any neutral (white) wire to
this control. Incorrect wiring will damage
this control.
!
WARNING
Do not connect any neutral (white) wire to
this control. Incorrect wiring will damage
this control.
4. Connect one black wire of wall control
to the “hot” wire in the wall box.
Securely connect wires with wire
connectors supplied (Figure 3).
6
BP7335 Palazzo
1/9/07
9:05 AM
Page 7
4. Install a wall control in the wall box
containing the “hot” wire first. Connect
one black wire of the wall control to the
“hot” wire. Securely connect wires with
wire connectors supplied.
5. Connect the other black wire of the wall
control to both remaining traveler
wire(s) in the wall box and secure with
wire connector supplied.
NOTE: Retrofit 3-way installations are
likely to include two traveler wires
between the two wall boxes. In new
construction, only one traveler wire is
required.
STANDARD WIRING FOR
EXISTING 3-WAY
CONTROLS
HOT
BLACK
OFF
ON
FAN/LIGHT
WALL
CONTROL
3-WAY WIRING DIAGRAM:
RETROFIT
HI
LIGHT
MED
LOW
BLK
TRAVELER
WIRE
NEUTRAL
REMOTE CONTROL
RECEIVER LOCATED
WITHIN THE CEILING
COVER
EXISTING
WALL CONTROL
BLK
FAN OFF
OFF
BLACK
HOT
TRAVELER WIRES
EMERSON ®
ON
BLK
LIGHT
LOAD
BLACK
HI
MED
LOW
FAN OFF
EMERSON®
BLK
TRAVELER WIRES
3-WAY WIRlNG DIAGRAM:
NEW CONSTRUCTION
HOT
EXISTING
WALL CONTROL
LOAD
Figure 5
LOAD
BLACK
GROUND
How to Assemble Your
Ceiling Fan
!
Figure 4
WARNING
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
6. Place wall control into wall box. Screw
in place and install decorator style
faceplate (included).
7. Next, install the other wall control into
the wall box containing the “load” wire.
Connect one black wire of the wall
control to the traveler wire(s) already
connected to the black wire (in the
other wall box). Secure with wire
connectors supplied.
8. Connect the other black wire of the wall
control to the “load” (black) wire and
secure with wire connector supplied.
9. Place the second wall control into the
wall box. Screw in place and install
decorator style faceplate (included).
Leave switch in “OFF” mode until fan
installation is completed.
10. Refer to “How to Assemble Your
Ceiling Fan” section to complete the
assembly of your ceiling fan.
1. Mount blade flanges to fan blades
using three #10-32 x 5/16” pan head
blade screws and three #10 flat blade
washers (supplied in loose parts bag)
(Figure 6).
!
WARNING
To reduce the risk of personal injury, do
not bend the blade flanges when
installing the flanges, balancing the
blades, or cleaning the fan. Do not insert
foreign objects between rotating fan
blades.
7
BP7335 Palazzo
1/9/07
FAN BLADE
9:05 AM
Page 8
4. Securely connect the black wire
connector of the light fitter assembly to
the black motor wire connector.
Securely connect the white wire of the
light fitter assembly to the white motor
wire (Figure 9).
#10-32 x 5/16" PAN
HEAD BLADE SCREW
(3 per blade)
#10 FLAT BLADE
WASHER
(3 per blade)
LIGHT FITTER
BLACK WIRE
BLADE
FLANGE
LIGHT FITTER
ASSEMBLY
MOTOR HOUSING
BLACK WIRE
MOTOR HOUSING
WHITE WIRE
Figure 6
LIGHT FITTER
WHITE WIRE
NOTE: Take care not to scratch fan
housing when installing blades.
2. Position the bottom half of the
styrofoam packaging on the floor
(Figure 7). Turn the fan motor assembly
upside down onto the styrofoam in
preparation for mounting the fan blade
assemblies.
LIGHT KIT
ADAPTER PLATE
Figure 9
5. Position the light fitter assembly so that
the three holes align with the one hole
and two keyhole slots in the light kit
adapter plate (Figure 10).
6. Attach the light fitter assembly to the
light kit adapter plate by securely
installing the three #8-32 x 1/4” pan
head screws (supplied in the loose
parts bag) (Figure 10).
FAN MOTOR ASSEMBLY
(Flange Slots Facing Up)
!
BOTTOM
HALF OF
STYROFOAM
WARNING
To avoid possible fire or shock, make
sure that the wires are not pinched
between the light fitter assembly and the
light kit adapter plate. Pinched wires will
also cause the light fitter assembly to
mount crooked on the light kit adapter
plate.
Figure 7
3. Carefully slide one blade assembly into
the motor housing assembly flange
slot. Attach the blade assembly using
two #10-32 x 5/16” oval head flange
screws (Figure 8). Make sure the
screws are securely tightened. Repeat
this procedure for the other four blade
assemblies.
#8-32 x 1/4" PAN
HEAD SCREW (3)
LIGHT FITTER
ASSEMBLY
#10-32 x 5/16" OVAL
HEAD FLANGE SCREW
(2 per flange)
BLADE
ASSEMBLY
Figure 10
MOTOR HOUSING
ASSEMBLY FLANGE
SLOT
Figure 8
8
BP7335 Palazzo
1/9/07
9:05 AM
Page 9
7. Carefully turn the fan motor assembly
upside down in preparation for hanger
ball/downrod installation. Place the
partially assembled fan into the top half
of the styrofoam as shown in Figure 11.
Do not rest fan weight on the light fitter
sockets.
11. Align the clevis pin holes in the
downrod with the holes in the motor
coupling. Install the clevis pin and
secure with the hairpin clip (Figure
13). (Pin and clip are supplied in loose
parts bag.) The clevis pin must go
through the holes in the motor
coupling and the holes in the
downrod. Push the straight leg of the
hairpin clip through the hole near the
end of the clevis pin until the curved
portion of the hairpin clip snaps
around the clevis pin. The hairpin clip
must be properly installed to prevent
the clevis pin from working loose. Pull
on the downrod to make sure the
clevis pin is properly installed.
TOP HALF OF
STYROFOAM
!
Figure 11
It is critical that the clevis pin in the motor
coupling is properly installed and the
setscrew securely tightened. Failure to
verify that the pin and setscrew are
properly installed (as shown in Figure 13)
could result in the fan falling.
8. Remove the hanger ball from the
downrod by loosening the setscrews in
the hanger ball until the ball falls freely
down the downrod (Figure 12).
Remove the pin from the downrod, then
remove the hanger ball. Retain the pin
and hanger ball for reinstallation in
Step 16.
12. While pulling up on the downrod,
tighten the two setscrews.
NOTE: The setscrews must be properly
tighten as described above, or fan
wobble could result.
13. The fan comes with black, blue, and
white leads that are 80” long.
Measure up approximately 6 to 9inches above the top of downrod. Cut
off excess leads and strip back
insulation 1/2” from end of leads.
14. Slide the coupling cover down the
downrod until it set firmly on the motor
housing (Figure 14).
PIN
HANGER
BALL
DOWNROD
SETSCREW
Figure 12
9.
Loosen both setscrews in the motor
coupling (Figure 13).
10. Separate, untwist and unkink the
three motor leads. Route the motor
leads through the downrod and seat
the downrod in the motor coupling
(Figure 13).
DOWNROD
COUPLING
COVER
DOWNROD
HAIRPIN
CLIP
CLEVIS PIN
SETSCREW (2)
Figure 14
Figure 13
WARNING
9
BP7335 Palazzo
1/9/07
9:05 AM
Page 10
15. Slide the ceiling cover over the
downrod until it rests on the coupling
cover (Figure 15). Be sure the cover
is oriented correctly, with the large
opening at the top.
17. You have now completed the
initial assembly of your new ceiling
fan. You can now proceed with
hanging and wiring your fan.
DOWNROD
CEILING
COVER
How to Hang
Your Ceiling Fan
COUPLING
COVER
!
WARNING
The fan must be hung with at least 7' of
clearance from floor to blades (Figure 17).
CEILING
Figure 15
16. Reinstall the hanger ball on the
downrod (Figure 16) as follows.
Route the motor leads through the
hanger ball and slide the hanger ball
over the downrod. Install the pin
through the holes at the top of the
downrod and slide the hanger ball up
the downrod, aligning the ball so the
pin is captured in the groove in the top
of the hanger ball. Pull the hanger ball
up tight against the pin and securely
tighten the setscrew in the hanger
ball. A loose setscrew could create
fan wobble.
AT
LEAST
7'
FLOOR
Figure 17
!
The outlet box and joist must be securely
mounted and capable of supporting at
least 50 lbs. Use only a U.L. outlet box
listed as “Acceptable for Fan Support of
50 Lbs. or Less”.
WARNING
!
It is critical that the clevis pin in the motor
coupling is properly installed and the
setscrew securely tightened. Failure to
verify that the pin and setscrew are
properly installed (as shown in Figure 12)
could result in the fan falling.
!
WARNING
To reduce the risk of fire, electric shock,
or personal injury, mount fan to outlet box
marked “Acceptable for Fan Support of
50 Lbs. or Less”, and use screws
supplied with outlet box. Most outlet
boxes commonly used for support of light
fixtures are not acceptable for fan
support and may need to be replaced.
Consult a qualified electrician if in doubt.
HANGER BALL
DOWNROD
WARNING
PIN
CEILING
COVER
SETSCREW
1. Securely attach the hanger bracket to
the outlet box using the two screws
supplied with the outlet box (Figure 18).
Figure 16
10
BP7335 Palazzo
!
1/9/07
9:05 AM
Page 11
How to Wire
Your Ceiling Fan
WARNING
Hanger bracket must seat firmly against
outlet box. If the outlet box is recessed,
remove wall board until bracket contacts
box. If bracket and/or outlet box are not
securely attached, the fan could wobble
or fall.
If you feel that you do not have enough
electrical
wiring
knowledge
or
experience, have your fan installed by a
licensed electrician.
!
OUTLET
BOX
TWO SCREWS
SUPPLIED
WITH
OUTLET BOX
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse box before wiring. All wiring must be
in accordance with National and Local
codes and the ceiling fan must be
properly grounded as a precaution
against possible electrical shock.
HANGER
BRACKET
TAB
Figure 18
2. Carefully lift the fan and seat the
hanger ball/downrod assembly on the
hanger bracket that was just attached
to the outlet box (Figure 19). Be sure
the groove in the ball is lined up with
the tab on the hanger bracket
(Figure 18).
!
CAUTION: To reduce the risk of
electrical shock, disconnect the
electrical supply circuit before
installing the fan, light kit or receiver.
1. Pull the wire leads, coming from the end
of the downrod, and the supply wires
through the open side of the hanger
bracket. (Figure 20).
WARNING
Failure to seat tab in groove could cause
damage to electrical wires and possible
shock or fire hazard.
2. Position the SW105 Receiver in the
ceiling cover so that the flat side of the
receiver faces up and the open portion
of the receiver is to the right, as shown
in Figure 20.
NOTE: CEILING COVER, SUPPLY WIRES AND FAN
WIRES OMITTED FOR CLARITY.
3. Using wire connectors (supplied),
make wiring connections as follows
(Figure 20 and 21):
a. Connect the white fan wire and the
white supply wire to the white
receiver wire (AC IN/ MOTOR N).
b. Connect the black fan wire to the
black receiver wire (TO MOTOR L).
c. Connect the black supply wire to the
black/white receiver wire (AC IN L).
d. Cut off the end of the blue receiver
wire and strip back insulation 1/2inch from the end of the wire.
e. Connect the blue fan wire to the blue
receiver wire (BOTTOM LIGHT).
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD
ASSEMBLY
Figure 19
!
WARNING
WARNING
To avoid possible fire or shock, do not
pinch wires between the hanger
ball/downrod assembly and hanger
bracket.
11
BP7335 Palazzo
1/9/07
9:05 AM
Page 12
f. Cap the receiver yellow wire using a
wire connector (supplied).
g. Connect the green ground wires
from the hanger bracket and the
hanger ball to the supply ground
wire (bare or green).
WARNING
!
Check to see that all connections are
tight, including ground, and that no bare
wire is visible at the wire connectors,
except for the ground wire. Do not
operate fan until blades are in place.
Noise and fan damage could result.
OUTLET BOX
BLACK SUPPLY WIRE
HANGER BRACKET
BLACK FAN WIRE
HANGER BRACKET
GROUND WIRE
(GREEN)
BLACK/WHITE RECEIVER WIRE
BLUE FAN WIRE
HANGER BALL
GROUND WIRE
(GREEN)
BLUE RECEIVER
WIRE
OPEN
PORTION OF
RECEIVER
HERE
SUPPLY GROUND
WIRE (GREEN OR
BARE)
CAP THE YELLOW RECEIVER WIRE
USING A WIRE CONNECTOR
RECEIVER
BLACK RECEIVER WIRE
WHITE SUPPLY
WIRE
WHITE RECEIVER WIRE
WHITE FAN WIRE
CEILING COVER
Figure 20
SW105 RECEIVER
BLACK
SUPPLY
WIRE
WHITE
RECEIVER
WIRE
BLACK
RECEIVER WIRE
BLACK/WHITE
RECEIVER WIRE
WHITE FAN WIRE
BLACK FAN WIRE
WIRE CONNECTOR
4. After connections have been made,
separate the white and green wires
from the black and blue wires.
5. Carefully turn the wires upward and
insert them up through the open side of
the hanger bracket and into the outlet
box. Push the green and white wires
into one side of the outlet box; push the
black and blue wires into the other side
of the outlet box.
6. Screw two 1-1/4” threaded studs
(supplied in the loose parts bag) into the
tapped holes in the hanger bracket
(Figure 22).
TO
110V
SUPPLY
HI
MED
U/L
D/L
LOW
REV
FAN OFF
OFF
ON
SW113
FAN/LIGHT
WALL
CONTROL
WHITE
SUPPLY
WIRE
BLUE RECEIVER
WIRE
YELLOW
RECEIVER WIRE
CAP THE
YELLOW
RECEIVER WIRE
USING A WIRE
CONNECTOR
BLUE FAN WIRE
DOWNROD
Figure 21
12
BP7335 Palazzo
1/9/07
9:05 AM
Page 13
How to Install
Your Light Kit
OUTLET
BOX
HANGER
BRACKET
CAUTION: To avoid risks of burns or
other injury, assure power is off before
attempting to install or replace the
candelabra base bulbs.
RECEIVER
1-1/4"
THREADED
STUDS (2)
1. Install two 60W (maximum) candelabra
base bulbs (not supplied) in the sockets
of the light fitter assembly (Figure 24).
2. Unscrew the decorative finial nut and
threaded washer from the light fitter
assembly threaded stud (Figure 24).
CEILING
COVER
Figure 22
7. Slide the receiver up and over the
hanger bracket. Press the receiver
against the ceiling, then slide the
ceiling cover up to the threaded studs
and turn until the studs protrude
through the holes in the ceiling cover
(Figure 23).
8. Secure the ceiling cover in place by
sliding lockwashers (supplied) over the
threaded studs and installing the two
knurled knobs (supplied) (Figure 23).
Tighten the knurled knobs securely
until the ceiling cover fits snugly against
the ceiling.
60W (MAX.)
CANDELABRA
BASE BULB (2)
THREADED
STUD
Figure 24
LIGHT FITTER
SOCKET (2)
THREADED
WASHER
DECORATIVE
FINIAL NUT
3. Slide the glass shade onto the
threaded stud until the glass rest
against the light fitter assembly (Figure
25).
4. Thread the previously removed
threaded washer and decorative finial
nut onto the threaded stud until finger
tight.
1-1/4" THREADED
STUD
LOCKWASHER
(2)
CEILING
COVER
KNURLED
KNOB (2)
Figure 23
!
WARNING
To avoid possible fire or shock, make
sure that the electrical wires are
completely inside the outlet box and
not pinched between the ceiling
cover and the ceiling.
GLASS
SHADE
Figure 25
THREADED
WASHER
DECORATIVE
FINIAL NUT
5. Your ceiling fan is now installed and
wired to be controlled by your fan/light
wall control.
13
BP7335 Palazzo
1/9/07
9:05 AM
Page 14
Operating Your
Ceiling Fan
5. To turn the light on and off, press and
release the LIGHT button. The light will
turn on at the light level previously set
(see step 4).
IMPORTANT
Fan installation must be completed,
including the installation of the fan
blades, before testing of the remote
control.
Your Fan/Light Wall Control (Figure 26)
has full control of your fan and light.
However, airflow direction is controlled by
a slide switch on the switch housing.
1. Restore electrical power to the outlet
box by turning the electricity on at the
service panel.
NOTE: Make sure that the ON/OFF slide
switch on the Fan/Light Wall Control is
in the ON position.
2. To set the desired fan speed, press the
HI, MED, or LOW buttons to operate
your fan on high, medium, or low speed
(Figure 26).
3. To turn your fan off, press the OFF
button.
4. To set the level of light brightness,
press and hold the LIGHT button. The
light brightness will continue to
increase then decrease while the
button is held down. When the light is
at the desired brightness, release the
button.
HI
LIGHT
MED
LOW
FAN OFF
EMERSON®
OFF
Figure 26
14
ON
BP7335 Palazzo
1/9/07
9:05 AM
Page 15
INSTRUCTION TO THE USER
(if device contains a digital device)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a Class B computing device,
pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception. The user is
cautioned that changes and modifications made to the equipment without the approval of
manufacturer could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
15
BP7335 Palazzo
1/9/07
9:05 AM
Page 16
Maintenance
Accessories
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
1. Downrod Extension Kits (see store or
catalog).
Periodic cleaning of your new ceiling fan is
the only maintenance that is needed.
2. Ceiling Fan Controls (see store or
catalog).
3. Blades (see store or catalog).
When cleaning, use only a soft brush or
lint free cloth to avoid scratching the finish.
!
Abrasive cleaning agents are not required
and should be avoided to prevent damage
to finish.
!
WARNING
The use of any other control not
specifically approved for this fan could
result in fire, shock and personal injury.
WARNING
!
Do not use water when cleaning your
ceiling fan. It could damage the motor or
the blades and create the possibility of an
electrical shock.
WARNING
This product is designed to use only
those parts supplied with this product
and/or any accessories designated
specifically for use with this product by
Emerson Electric Co. Substitution of
parts or accessories not designated for
use with this product by Emerson Electric
Co. could result in personal injury or
property damage.
16
BP7335 Palazzo
1/9/07
9:05 AM
Page 17
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX
!
OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN.
Trouble Shooting
TROUBLE
1. Fan will not
start.
PROBABLE CAUSE
1. Fuse or circuit breaker
blown.
2. Loose power line
connections to the fan.
3. Fan/Light Wall Control is OFF.
4. Code switches in remote
control receiver and Fan/Light
Wall Control are not set in the
same position.
2. Fan sounds
noisy.
1. Blades not attached to fan.
2. Screws securing fan blade
flanges to motor are loose.
3. Screws holding blades to
flanges are loose.
SUGGESTED REMEDY
1. Check main and branch
circuit fuses or circuit breakers.
! WARNING: Make sure
main power is turned off.
2. Check line power connections
to fan.
3. Turn ON Fan/Light Wall Control.
4. Check that both code switches
are set in the same positions.
1. Attach blades to fan before
operating.
2. Check to make sure the screws
which attach the blade flanges
to the motor are tight.
3. Tighten screws securely.
WARNING: Make sure main
power is turned off.
4. Loose screws in motor housing. 4. Check to make sure all screws
in motor housing are snug
(not over-tight)
!
3. Fan wobbles
excessively.
1. Setscrews in motor coupling is
not tightened securely.
2. Setscrew in the hanger ball/
downrod assembly is loose.
3. Screws securing fan blade
flanges to motor hub are loose.
4. Fan blade flanges not seated
properly.
5. Hanger bracket and/or ceiling
outlet box is not securely
fastened.
6. Fan blades out of balance.
17
1. Raise coupling cover and
tighten setscrews securely.
2. Tighten the setscrew in the
hanger ball/downrod assembly.
3. Check to be sure screws which
attach the fan blade flanges
to the motor hub are tight.
4. Check to be sure that the
screws securing the fan
blade flanges seat firmly.
5. Tighten the hanger bracket
screws to the outlet box, and/or
secure outlet box.
6. Interchanging an adjacent (side
by-side) blade pair can
redistribute the weight and result
in smoother operation.
BP7335 Palazzo
1/9/07
9:05 AM
Page 18
Repair Parts
1
2
9
3
24
14
6
10
11
15
23
HI
LIGHT
MED
LOW
REV
FAN OFF
OFF
ON
20
8
7
16
4
5
21
18
19
17
22
12
13
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• NAME OF ITEM
• PART DESCRIPTION
• MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone 1-800-654-3545.
18
BP7335 Palazzo
1/9/07
9:05 AM
Page 19
Repair Parts Listing
Part Numbers
Key
No.
Description
Model No.
CF943AGW00
Model No.
CF943BZH00
761655-62
—
—
—
761655-61
—
—
—
763224
763224
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
*
1
2
3
Hanger Pack, Consisting of:
Hanger Bracket
Hanger Ball
Downrod
*
4
13
Parts Bag, Containing:
Screw, #10-32 x 5/16”
Pan Head Blade (16)
Washer, #10 flat (16)
Wire Connector (5)
Clevis Pin (1)
Hairpin Clip (1)
Threaded Stud #8-32 x 1-1/4” (2)
Lockwasher, #8 External Tooth (2)
Knurled Knob, #8-32 (2)
Screw, #10-32 x 5/16”
Oval Head Flange (11)
Screw, #8-32 x 1/4” Pan Head (4)
14
Cover, Ceiling
763210-AGW
763210-BZH
15
Cover, Coupling
763211-AGW
763211-BZH
5
6
7
8
9
10
11
12
16
Fan Housing Assembly
—
—
17
Flange Assembly (full set for one fan)
763215-AGW
763215-BZH
763217-AGW
763217-DC
763220-BQ
763220-BQ
18
Blade Set (full set for one fan)
19
Light Fitter Assembly
20
Harness, Wiring with Reverse Module
763264
763264
21
Glass Shade
763222-AMT
763222-AMT
22
Nut, Finial
763223-AGW
763223-BZH
23
Wall Control, Fan/Light
762349
762349
24
Receiver, Remote Control
762401
762401
—
Owner's Manual
BP7335
BP7335
19
BP7335 Palazzo
1/9/07
9:05 AM
Page 20
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against
all defects in workmanship and materials. You must be the original purchaser or user of the product to be
covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for a lifetime of your ceiling fan. All other components and
accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH
RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other
accessory at no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time
and no replacement can be provided, Emerson Electric Co. will refund the actual purchase price of your fan. We
will ship the repaired product or replacement to you at no charge, but you are responsible for all costs
of removal, reinstallation and shipping of the product to Emerson.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY
SERVICE. KEEP YOUR RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our
factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air
Comfort Products, Division of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all
model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest
authorized service center. You will be responsible for all insurance, freight or other transportation charges to our
factory or authorized service center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid
damage in transit since we will not be responsible for any such damage.
What Is Not Covered:
The lower glass of your ceiling fan is not covered by this warranty. This warranty also does not cover any defects,
malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal
wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are
voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written
or oral warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on
behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS
WARRANTY AND EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING
INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such
damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of
repairing or replacing other property which was damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above
exclusion or limitation may not apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant ¥ St. Louis, MO 63136
Part No. F40BP73350000
Printed in China 01/07
Form No. BP7335