Brocade Communications Systems 6510 Installation guide

53-1002174-10
08 May 2015
Brocade 6510
Hardware Installation Guide
© 2015, Brocade Communications Systems, Inc. All Rights Reserved.
ADX, Brocade, Brocade Assurance, the B-wing symbol, DCX, Fabric OS, HyperEdge, ICX, MLX, MyBrocade, OpenScript, The Effortless
Network, VCS, VDX, Vplane, and Vyatta are registered trademarks, and Fabric Vision and vADX are trademarks of Brocade
Communications Systems, Inc., in the United States and/or in other countries. Other brands, products, or service names mentioned may be
trademarks of others.
Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any
equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document
at any time, without notice, and assumes no responsibility for its use. This informational document describes features that may not be
currently available. Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in
this document may require an export license from the United States government.
The authors and Brocade Communications Systems, Inc. assume no liability or responsibility to any person or entity with respect to the
accuracy of this document or any loss, cost, liability, or damages arising from the information contained herein or the computer programs that
accompany it.
The product described by this document may contain open source software covered by the GNU General Public License or other open
source license agreements. To find out which open source software is included in Brocade products, view the licensing terms applicable to
the open source software, and obtain a copy of the programming source code, please visit http://www.brocade.com/support/oscd.
Contents
Preface..................................................................................................................................... 5
Document conventions......................................................................................5
Text formatting conventions.................................................................. 5
Command syntax conventions.............................................................. 5
Notes, cautions, and warnings.............................................................. 6
Brocade resources............................................................................................ 7
Contacting Brocade Technical Support.............................................................7
Document feedback.......................................................................................... 8
About This Document................................................................................................................ 9
Supported hardware and software.................................................................... 9
What’s new in this document............................................................................ 9
Brocade 6510 Introduction.....................................................................................................11
Brocade 6510 overview...................................................................................11
Platform capabilities............................................................................ 11
Platform components.......................................................................... 12
Facility requirements....................................................................................... 13
Port side of the Brocade 6510.........................................................................14
Nonport side of the Brocade 6510.................................................................. 15
Brocade 6510 Installation and Configuration.......................................................................... 17
Items included with the Brocade 6510............................................................ 17
Installation and safety considerations............................................................. 17
Installation precautions....................................................................... 17
ESD precautions................................................................................. 18
Power precautions.............................................................................. 18
RTC battery.........................................................................................19
Environmental considerations............................................................. 19
EIA rack installation considerations.................................................... 19
Recommendations for cable management......................................... 20
Items required for installation.............................................................. 20
Standalone installation for a Brocade 6510.................................................... 21
Rack installation for a Brocade 6510.............................................................. 21
Brocade 6510 configuration............................................................................ 21
Providing power to the switch............................................................. 21
Creating a serial connection................................................................22
Switch IP address............................................................................... 22
Date and time settings........................................................................ 23
Brocade Inter-Switch Link (ISL) Trunking........................................... 26
Fabric OS Native and Access Gateway modes.............................................. 26
Access Gateway default port mapping................................................27
Disabling and enabling Access Gateway mode.................................. 27
Brocade 6510 Operation........................................................................................................ 29
Powering the Brocade 6510 on and off...........................................................29
Brocade 6510 Hardware Installation Guide
53-1002174-10
3
LED activity interpretation............................................................................. 29
Brocade 6510 LEDs.......................................................................... 29
LED locations.................................................................................... 30
LED patterns..................................................................................... 31
POST and boot specifications.......................................................................33
POST................................................................................................ 33
Boot...................................................................................................33
Interpreting POST results..............................................................................34
Brocade 6510 Maintenance.......................................................................... 34
Installing an SFP+.............................................................................34
Brocade 6510 Management..........................................................................37
Power supply, fan assembly, and airflow direction support matrix...........................................39
Removal and replacement of power supplies and fans........................................................... 41
Introduction................................................................................................... 41
Removing and replacing a power supply and fan assembly......................... 42
Determining the need to replace a power supply and fan
assembly..................................................................................... 45
Time Required...................................................................................45
Items Required..................................................................................45
Removing a power supply and fan assembly................................... 46
Replacing a power supply and fan assembly....................................47
Brocade 6510 Switch Technical Specifications..................................................................... 49
Regulatory Statements..........................................................................................................57
BSMI statement (Taiwan)..............................................................................57
Canadian requirements.................................................................................57
CE Statement................................................................................................57
China CC statement......................................................................................58
China ROHS................................................................................................. 59
FCC warning (US only)................................................................................. 59
Germany....................................................................................................... 59
KCC statement (Republic of Korea)..............................................................59
VCCI statement.............................................................................................59
Caution and Danger Notices..................................................................................................61
Cautions........................................................................................................61
Danger Notices............................................................................................. 64
4
Brocade 6510 Hardware Installation Guide
53-1002174-10
Preface
● Document conventions......................................................................................................5
● Brocade resources............................................................................................................ 7
● Contacting Brocade Technical Support.............................................................................7
● Document feedback.......................................................................................................... 8
Document conventions
The document conventions describe text formatting conventions, command syntax conventions, and
important notice formats used in Brocade technical documentation.
Text formatting conventions
Text formatting conventions such as boldface, italic, or Courier font may be used in the flow of the text
to highlight specific words or phrases.
Format
Description
bold text
Identifies command names
Identifies keywords and operands
Identifies the names of user-manipulated GUI elements
Identifies text to enter at the GUI
italic text
Identifies emphasis
Identifies variables
Identifies document titles
Courier font
Identifies CLI output
Identifies command syntax examples
Command syntax conventions
Bold and italic text identify command syntax components. Delimiters and operators define groupings of
parameters and their logical relationships.
Convention
Description
bold text
Identifies command names, keywords, and command options.
italic text
Identifies a variable.
value
In Fibre Channel products, a fixed value provided as input to a command
option is printed in plain text, for example, --show WWN.
Brocade 6510 Hardware Installation Guide
53-1002174-10
5
Notes, cautions, and warnings
Convention
Description
[]
Syntax components displayed within square brackets are optional.
Default responses to system prompts are enclosed in square brackets.
{x|y|z}
A choice of required parameters is enclosed in curly brackets separated by
vertical bars. You must select one of the options.
In Fibre Channel products, square brackets may be used instead for this
purpose.
x|y
A vertical bar separates mutually exclusive elements.
<>
Nonprinting characters, for example, passwords, are enclosed in angle
brackets.
...
Repeat the previous element, for example, member[member...].
\
Indicates a “soft” line break in command examples. If a backslash separates
two lines of a command input, enter the entire command at the prompt without
the backslash.
Notes, cautions, and warnings
Notes, cautions, and warning statements may be used in this document. They are listed in the order of
increasing severity of potential hazards.
NOTE
A Note provides a tip, guidance, or advice, emphasizes important information, or provides a reference
to related information.
ATTENTION
An Attention statement indicates a stronger note, for example, to alert you when traffic might be
interrupted or the device might reboot.
CAUTION
A Caution statement alerts you to situations that can be potentially hazardous to you or cause
damage to hardware, firmware, software, or data.
DANGER
A Danger statement indicates conditions or situations that can be potentially lethal or
extremely hazardous to you. Safety labels are also attached directly to products to warn of
these conditions or situations.
6
Brocade 6510 Hardware Installation Guide
53-1002174-10
Brocade resources
Brocade resources
Visit the Brocade website to locate related documentation for your product and additional Brocade
resources.
You can download additional publications supporting your product at www.brocade.com. Select the
Brocade Products tab to locate your product, then click the Brocade product name or image to open the
individual product page. The user manuals are available in the resources module at the bottom of the
page under the Documentation category.
To get up-to-the-minute information on Brocade products and resources, go to MyBrocade. You can
register at no cost to obtain a user ID and password.
Release notes are available on MyBrocade under Product Downloads.
White papers, online demonstrations, and data sheets are available through the Brocade website.
Contacting Brocade Technical Support
As a Brocade customer, you can contact Brocade Technical Support 24x7 online, by telephone, or by email. Brocade OEM customers contact their OEM/Solutions provider.
Brocade customers
For product support information and the latest information on contacting the Technical Assistance
Center, go to http://www.brocade.com/services-support/index.html.
If you have purchased Brocade product support directly from Brocade, use one of the following methods
to contact the Brocade Technical Assistance Center 24x7.
Online
Telephone
E-mail
Preferred method of contact for nonurgent issues:
Required for Sev 1-Critical and Sev
2-High issues:
support@brocade.com
• My Cases through MyBrocade
•
Continental US: 1-800-752-8061
• Software downloads and licensing •
tools
Europe, Middle East, Africa, and
Asia Pacific: +800-AT FIBREE
(+800 28 34 27 33)
• Knowledge Base
•
For areas unable to access toll
free number: +1-408-333-6061
•
Toll-free numbers are available in
many countries.
Please include:
•
Problem summary
•
Serial number
•
Installation details
•
Environment description
Brocade OEM customers
If you have purchased Brocade product support from a Brocade OEM/Solution Provider, contact your
OEM/Solution Provider for all of your product support needs.
• OEM/Solution Providers are trained and certified by Brocade to support Brocade® products.
• Brocade provides backline support for issues that cannot be resolved by the OEM/Solution Provider.
Brocade 6510 Hardware Installation Guide
53-1002174-10
7
Document feedback
• Brocade Supplemental Support augments your existing OEM support contract, providing direct
access to Brocade expertise. For more information, contact Brocade or your OEM.
• For questions regarding service levels and response times, contact your OEM/Solution Provider.
Document feedback
To send feedback and report errors in the documentation you can use the feedback form posted with
the document or you can e-mail the documentation team.
Quality is our first concern at Brocade and we have made every effort to ensure the accuracy and
completeness of this document. However, if you find an error or an omission, or you think that a topic
needs further development, we want to hear from you. You can provide feedback in two ways:
• Through the online feedback form in the HTML documents posted on www.brocade.com.
• By sending your feedback to documentation@brocade.com.
Provide the publication title, part number, and as much detail as possible, including the topic heading
and page number if applicable, as well as your suggestions for improvement.
8
Brocade 6510 Hardware Installation Guide
53-1002174-10
About This Document
● Supported hardware and software.................................................................................... 9
● What’s new in this document............................................................................................ 9
Supported hardware and software
This document includes information specific to the Brocade 6510 running Brocade Fabric OS version
5.3.0 and later.
What’s new in this document
• The FRUs removal and replacement procedures chapter is updated with DC power supply FRU
information.
• An illustration indicating the Brocade 6510 port groups and port numbers is added.
• The Brocade 6510 switch does not configure ports as FL_Ports and therefore all references to the
"FL_Port (fabric loop enabled)" is removed.
• The Brocade 6510 does not support enclosed cabinets and hence all the references to the cabinets
are changed to EIA racks.
• The fan assembly airflow direction indications and descriptions are corrected.
• The regulatory statements and certification details are updated.
• The China RoHS environmental compliance statements are replaced with reference to the latest
independent China RoHS document part number.
• A new section listing all the caution and danger notices is added.
Brocade 6510 Hardware Installation Guide
53-1002174-10
9
What’s new in this document
10
Brocade 6510 Hardware Installation Guide
53-1002174-10
Brocade 6510 Introduction
● Brocade 6510 overview...................................................................................................11
● Facility requirements....................................................................................................... 13
● Port side of the Brocade 6510.........................................................................................14
● Nonport side of the Brocade 6510.................................................................................. 15
Brocade 6510 overview
The Brocade 6510 is a 48-port auto-sensing 2, 4, 8, or 16 Gbps as well as 10 Gbps Fibre Channel (FC)
switch that delivers the latest Brocade single-chip architecture for Fibre Channel Storage Area Networks
(SANs). The Brocade 6510 is an enterprise-class switch that is designed to handle the large-scale SAN
requirements of an enterprise, and can also be used to address the SAN requirements of a small to
medium-sized workgroup.
The Brocade 6510 provides 48 ports in a single (1U) height switch that enables the creation of very
dense fabrics in a relatively small space.
The Brocade 6510 offers Ports on Demand (POD) licensing as well. “Base” models of the switch
contain 24 ports, and up to two additional 12-port POD licenses can be purchased. The Brocade 6510
provides excellent overall value as the foundation of a SAN with the ability to grow with an
organization’s SAN needs.
The Brocade 6510 supplies Reliability, Availability, and Serviceability (RAS) performance and scalability
requirements of an enterprise switch along with interoperability and ease-of-use advantages.
The Brocade 6510 can also be configured in Access Gateway mode that lets you configure your
Enterprise fabric to handle additional N_Ports instead of domains. By reducing the number of domain
IDs and ports you simplify configuration and management in a large fabric.
Switches in AG mode are logically transparent to the host and the fabric. You can increase the number
of hosts that have access to the fabric without increasing the number of switches.
The Brocade 6510 is less than 18 inches deep, allowing for greater installation flexibility. It also has
airflow direction options. You can order either port side exhaust (the default configuration) or nonport
side exhaust airflow to accommodate specific installations.
Platform capabilities
The Brocade 6510 offers the following features and capabilities:
• Up to 48 auto-sensing ports of high-performance 16 Gbps technology in a single domain.
• Ports on Demand scaling from 24 to 36 or 48 ports.
• 2, 4, 8, and 16 Gbps auto-sensing Fibre Channel switch and router ports.
‐
2, 4, and 8 Gbps performance is enabled by 8 Gbps SFP+ transceivers.
‐
4, 8, and 16 Gbps performance is enabled by 16 Gbps SFP+ transceivers.
• 10 Gbps manual set capability on FC ports (requires the optional 10 Gigabit FCIP/Fibre Channel
license).
Brocade 6510 Hardware Installation Guide
53-1002174-10
11
Platform components
‐
10 Gbps performance is enabled by 10 Gbps SFP+ transceivers.
‐
Ports can be configured for 10 Gbps for metro connectivity (on the first eight ports only).
• Universal ports self-configure as E, F, M, or D ports. EX_Ports can be activated on a per port basis
with the optional Integrated Routing license.
‐
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Brocade Diagnostic Port (D-Port) feature provides physical media diagnostic,
troubleshooting and verification services.
In-flight data compression and encryption on up to two ports provides efficient link utilization and
security.
Options for port side exhaust (default) or nonport side exhaust airflow for cooling.
Virtual Fabric support to improve isolation between different VFs.
Fibre Channel Routing (FCR) service, available with the optional Integrated Routing license
provides improved scalability and fault isolation.
FICON, FICON Cascading, and FICON Control Unit Port ready.
Inter-Switch Link (ISL) Trunking (licensable), which allows up to eight ports (at 2, 4, 8, or 16 Gbps
speeds) between a pair of switches combined to form a single, logical ISL with a speed of up to 128
Gbps (256 Gbps full duplex) for optimal bandwidth utilization and load balancing.
Dynamic Path Selection (DPS), which optimizes fabric-wide performance and load balancing by
automatically routing data to the most efficient available path in the fabric.
Brocade-branded SFP+ optical transceivers that support any combination of Short Wavelength
(SWL) and Long Wavelength (LWL) or Extended Long Wavelength (ELWL) optical media among
the switch ports.
Extended distance support enables native Fibre Channel extension up to 7,500 km at 2 Gbps.
Support for unicast, multicast (255 groups), and broadcast data traffic types.
Brocade Fabric OS, which delivers distributed intelligence throughout the network and enables a
wide range of value-added applications including Brocade Advanced Web Tools and Brocade
Zoning. Optional Fabric Services include: Adaptive Networking with QoS, Brocade Extended
Fabrics, Brocade Enhanced Group Management, Brocade Fabric Watch, ISL Trunking, and End-toEnd Performance Monitoring (APM).
Support for Access Gateway configuration where server ports connected to the fabric core will be
virtualized.
Hardware zoning is accomplished at the port level of the switch and by World Wide Name (WWN).
Hardware zoning permits or denies delivery of frames to any destination port address.
Extensive diagnostics and system-monitoring capabilities for enhanced high Reliability, Availability,
and Serviceability (RAS).
10G Fibre Channel integration on the same port provides for DWDM metro connectivity on the
same switch (can be done on first eight ports only).
The Brocade EZSwitchSetup wizard that makes SAN configuration a three-step point-and-click
task.
Real time power monitoring enables users to monitor real time power usage of the fabric at a switch
level.
Port-to-port latency minimized to 800 nanoseconds through the use of cut-through frame routing at
16 Gbps.
Platform components
• A system motherboard that features a PowerPC 440EPx Reduced Instruction Set Computer (RISC)
CPU running at 667 MHz, with integrated peripherals, and that provides high performance with low
power consumption.
• An RJ45 10/100 Bast T Ethernet system management port, in conjunction with EZSwitchSetup, that
supports switch IP address discovery and configuration, eliminating the need to attach a serial cable
to configure the switch IP address and greatly increasing the ease of use.
12
Brocade 6510 Hardware Installation Guide
53-1002174-10
Facility requirements
• One RS-232 serial port with RJ45 connector for initial switch setup (if not using EZSwitch Setup) and
factory default restoration. (the integral LEDs remain unlit at all times)
• A USB port that provides storage for firmware updates, output of the supportSave command and
storage for configuration uploads and downloads.
• Two hot-swappable, redundant power supply and fan FRUs. There are two fans per FRU.
• Rack-mount design (1U form factor) in a 19-inch EIA rack.
• One LED (green/amber) per FC port to indicate status.
• One LED (green) for system power.
• One LED (green/amber) for system status.
• Two Ethernet LEDs (integrated with RJ45) for speed and activity status.
• SEEPROM for switch identification.
• Voltage monitoring.
• Fan monitoring including flow direction.
• Temperature monitoring.
• Real-time clock (RTC) with battery.
• The Brocade EZSwitchSetup wizard that makes SAN configuration a three-step point-and-click task.
Facility requirements
The following table provides the facilities requirements that must be met for the Brocade 6510.
TABLE 1 Facility Requirements
Type
Requirements
Electrical
• Adequate supply circuit, line fusing, and wire size, as specified by the electrical rating on the
switch nameplate
• Circuit protected by a circuit breaker and grounded in accordance with local electrical codes
Refer to Brocade 6510 Technical Specifications on page 0
specifications.
Thermal
for complete power supply
• A minimum air flow of 79.8 cubic meters/hour (47 cubic ft/min.) available in the immediate
vicinity of the switch.
NOTE
Although this airflow may exceed the airflow maximum listed in the device Technical
Specifications, the additional airflow is recommended to pressurize the inlet (cool isle) side of
rack installations relative to the exhaust side to minimize recirculation of hot air back to the inlet
side.
• Ambient air temperature not exceeding 40 ° C (104 ° F) while the switch is operating
Rack (when
rack-mounted)
Brocade 6510 Hardware Installation Guide
53-1002174-10
•
One rack unit (1U) in a 48.3 cm (19-inch) rack - must use rack kits designed for the extra width
of the Brocade 6510 switch to mount in standard racks
•
All equipment in rack grounded through a reliable branch circuit connection
•
Additional weight of switch not to exceed the rack’s weight limits
•
Rack secured to ensure stability in case of unexpected movement
13
Port side of the Brocade 6510
Port side of the Brocade 6510
The port side of the Brocade 6510 includes the system status LED, console port, Ethernet port and
LEDs, USB port, and Fibre Channel ports and the corresponding port status LEDs.
FIGURE 1 Port side view of the Brocade 6510
1. System status LED
2. Management Ethernet port with LEDs
3. USB port
4. FC ports 0-3(all LEDs above)
5. FC ports 40-43
6. FC ports 44-47
7. FC ports 4-7
8. Switch ID pull-out tab
9. Serial console port
10.System power LED
NOTE
The two LEDs on the serial console port are non-functional.
The following illustration helps you to identify the port groups and port numbers.
FIGURE 2 Brocade 6510 port groups and port numbers
1.
2.
3.
4.
5.
6.
14
Port group 1; PID 00 to 07
Port group 2; PID 08 to 15
Port group 3; PID 16 to 23
Port group 4; PID 24 to 31
Port group 5; PID 32 to 39
Port group 6; PID 40 to 47
Brocade 6510 Hardware Installation Guide
53-1002174-10
Nonport side of the Brocade 6510
NOTE
You can also use port index and PIDs to identify a port. For more information, refer to the Fabric OS
Administrator's Guide.
Nonport side of the Brocade 6510
The following figure shows the nonport side of the Brocade 6510, which contains the power supply
including the power receptacle and power switch (only on AC PS) and fan assemblies.
FIGURE 3 Nonport side of the Brocade 6510 with the AC power supply
1. Power supply/fan assembly #2
2. Power supply/fan assembly #1
FIGURE 4 Nonport side of the Brocade 6510 with the DC power supply
1. Power supply/fan assembly #2
2. Power supply/fan assembly #1
Brocade 6510 Hardware Installation Guide
53-1002174-10
15
Nonport side of the Brocade 6510
16
Brocade 6510 Hardware Installation Guide
53-1002174-10
Brocade 6510 Installation and Configuration
● Items included with the Brocade 6510............................................................................ 17
● Installation and safety considerations............................................................................. 17
● Standalone installation for a Brocade 6510.................................................................... 21
● Rack installation for a Brocade 6510.............................................................................. 21
● Brocade 6510 configuration............................................................................................ 21
● Fabric OS Native and Access Gateway modes.............................................................. 26
Items included with the Brocade 6510
The following items are included with the standard shipment of a fully-configured Brocade 6510. When
you open the Brocade 6510 packaging, verify that these items are included in the package and that no
damage has occurred during shipping:
• The Brocade 6510 switch, containing two combined power and fan assemblies (incorporating either
nonport side exhaust or port side exhaust airflow as ordered - airflow labels on the nonport side
exhaust assemblies)
• 16-Gbps or 8-Gbps SFP+ modules for the Fibre Channel ports (speed and quantity as ordered)
• One accessory kit, containing the following items:
‐
‐
‐
‐
‐
Serial cable with an RJ45 connector
Two 6 ft. Power Cords
Rubber feet, required for setting up the switch as a standalone unit
Brocade 6510 EZSwitch Setup poster
EZSwitch Setup CD
Installation and safety considerations
You can install the Brocade 6510 switch in the following ways:
1. As a standalone unit on a flat surface.
2. In an EIA rack using a slim rail rack mount kit. The rack mount kit can be ordered from your switch
retailer.
3. In an EIA rack using an optional mid-mount rack kit for switches. The optional mid-mount rack kit for
switches can be ordered from your switch retailer.
Installation precautions
When using this product, observe all danger, caution, and attention notices in this manual. The notices
are accompanied by symbols that represent the severity of the safety condition.
Brocade 6510 Hardware Installation Guide
53-1002174-10
17
ESD precautions
NOTE
Refer to Cautions and Danger Noticesfor translations of safety notices for this product.
ESD precautions
The Brocade 6510 contains electrostatic discharge (ESD) sensitive FRUs. When working with any
Brocade 6510 FRU, use correct ESD procedures.
CAUTION
Before plugging a cable into to any port, be sure to discharge the voltage stored on the cable
by touching the electrical contacts to ground surface.
CAUTION
Static electricity can damage the chassis and other electronic devices. To avoid damage, keep
static-sensitive devices in their static-protective packages until you are ready to install them.
Wear a wrist grounding strap connected to chassis ground (if the Brocade 6510 is plugged in) or a
bench ground.
DANGER
For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.
Power precautions
To install and operate the switch successfully, ensure the following:
• The primary outlet is correctly wired, protected by a circuit breaker, and grounded in accordance
with local electrical codes.
• Connect the power cord only to a grounded outlet.
DANGER
Make sure that the power source circuits are properly grounded, then use the power cord
supplied with the device to connect it to the power source.
• The supply circuit, line fusing, and wire size are adequate, as specified by the electrical rating on
the switch nameplate.
• This switch might have more than one power cord. To reduce the risk of electric shock, disconnect
both power cords before servicing.
DANGER
Remove both power cords before servicing.
DANGER
Disconnect the power cord from all power sources to completely remove power from the
device.
• This product is designed for an IT power system with phase-to-phase voltage of 230V. After
operation of the protective device, the equipment is still under voltage if it is connected to an IT
power system.
18
Brocade 6510 Hardware Installation Guide
53-1002174-10
RTC battery
DANGER
To avoid high voltage shock, do not open the device while the power is on.
• The power supply standards provided in, Brocade 6510 Technical Specifications on page 0
met.
are
RTC battery
Do not attempt to replace the real-time clock (RTC) battery. There is danger of explosion if the battery is
incorrectly replaced or disposed of. Contact your switch supplier if the real-time clock begins to lose
time.
DANGER
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according
to the instructions.
Environmental considerations
For successful installation and operation of the switch, ensure that the following environmental
requirements are met:
• At a minimum, adequate cooling requires that you install the switch with the intake side, as indicated
by the airflow direction of the fan assemblies, facing the cool-air aisle.
• All equipment in the rack should force air in the same direction to avoid intake of exhaust air.
CAUTION
Ensure that the airflow direction of the power supply unit matches that of the installed fan
tray. The power supplies and fan trays are clearly labeled with either a green arrow with an
"E", or an orange arrow with an "I."
• A maximum of 102 cubic meters/hour (60 cubic feet/minute) and a minimum of 74.8 cubic meters/
hour (44 cubic feet/minute) of air flow is available for air intake.
CAUTION
Make sure the airflow around the front, sides, and back of the device is not restricted.
• Ensure temperature requirements are met.
CAUTION
Do not install the device in an environment where the operating ambient temperature might
exceed 40°C (104°F).
EIA rack installation considerations
For successful installation and operation of the switch in an EIA rack, ensure the following requirements
are met:
• It must be a standard EIA rack.
• A space that is one rack unit (1U) high; 4.45 cm (1.75 inches) high and 48.3 cm (19 inches) wide.
• The two rack kit options for the Brocade 6510 use rails that are slimmer than standard rails to
accommodate the slightly wider chassis. Be sure to use one of these kits. Do not use standard rails
to install the Brocade 6510 in a rack, they will not fit with the switch.
Brocade 6510 Hardware Installation Guide
53-1002174-10
19
Recommendations for cable management
• The equipment in the rack is grounded through a reliable branch circuit connection and maintain
ground at all times. Do not rely on a secondary connection to a branch circuit, such as a power
strip.
• Airflow and temperature requirements are met on an ongoing basis, particularly if the switch is
installed in a closed or multi-rack assembly.
• The additional weight of the switch does not exceed the rack’s weight limits or unbalance the rack in
any way.
• The rack is secured to ensure stability in case of unexpected movement, such as an earthquake.
DANGER
Make sure the rack or cabinet housing the device is adequately secured to prevent it from
becoming unstable or falling over.
Recommendations for cable management
The minimum bend radius for a 50 micron cable is 2 inches under full tensile load and 1.2 inches with
no tensile load.
Cables can be organized and managed in a variety of ways, for example, using cable channels on the
sides of the rack or patch panels to minimize cable management. Following is a list of
recommendations:
NOTE
You should not use tie wraps with optical cables because they are easily overtightened and can
damage the optic fibers.
CAUTION
Before plugging a cable into to any port, be sure to discharge the voltage stored on the cable
by touching the electrical contacts to ground surface.
• Plan for rack space required for cable management before installing the switch.
• Leave at least 1 m (3.28 ft) of slack for each port cable. This provides room to remove and replace
the switch, allows for inadvertent movement of the rack, and helps prevent the cables from being
bent to less than the minimum bend radius.
• If you are using Brocade ISL Trunking, consider grouping cables by trunking groups. The cables
used in trunking groups must meet specific requirements, as described in the Fabric OS
Administrator’s Guide .
• For easier maintenance, label the fiber optic cables and record the devices to which they are
connected.
• Keep LEDs visible by routing port cables and other cables away from the LEDs.
• Use hook and loop style straps to secure and organize fiber optic cables.
Items required for installation
The following items are required for installing, configuring, and connecting the Brocade 6510 for use in
a network and fabric:
•
•
•
•
20
Workstation with an installed terminal emulator, such as HyperTerminal
Unused IP address and corresponding subnet mask and gateway address
Serial cable (provided) if not using EZSwitch Setup
Ethernet cable
Brocade 6510 Hardware Installation Guide
53-1002174-10
Standalone installation for a Brocade 6510
• Brocade-branded SFP+s and compatible cables (Brocade-branded 16 Gbps SFP+s required for 16
Gbps performance), as required
• Access to an FTP server or USB device for backing up the switch configuration (optional)
Standalone installation for a Brocade 6510
Perform this task to install the Brocade 6510 as a standalone unit.
1. Unpack the Brocade 6510 and verify the items listed on Items included with the Brocade 6510 on
page 17. Verify the items are present and undamaged.
2. Apply the adhesive rubber feet. Applying the rubber feet onto the switch helps prevent the switch
from sliding off the supporting surface.
a)
b)
Clean the indentations at each corner of the bottom of the switch to ensure that they are
free of dust or other debris that might lessen the adhesion of the feet.
With the adhesive side against the chassis, place one rubber foot in each indentation and
press into place.
3. Place the switch on a flat, sturdy surface.
4. Provide power to the switch as described in Providing power to the switch on page 21.
ATTENTION
Do not connect the switch to the network until the IP address is correctly set. For instructions on how
to set the IP address, see Brocade 6510 configuration on page 21
Rack installation for a Brocade 6510
Follow the installation instructions shipped with the appropriate rack mount kit:
• To install the switch into a fixed-rail rack, refer to the Slim Rail Rack Mount Kit Installation
Procedure .
Brocade 6510 configuration
Once you have set up the Brocade 6510 in a rack or as a standalone switch, it is time to give it power
and a basic configuration. If you are going to use the Brocade 6510 in a single-switch setup, you can
use EZSwitchSetup to complete the basic configuration.
See the EZSwitchSetup CD , included with the Brocade 6510, for more information. You can also use
the Brocade 6510 EZSwitchSetup poster .
If you do not want to use EZSwitch Setup, follow the instructions in the rest of this section.
Providing power to the switch
Perform the following steps to provide power to the Brocade 6510.
Brocade 6510 Hardware Installation Guide
53-1002174-10
21
Creating a serial connection
1. Connect the power cords to both power supplies, and then to power sources on separate circuits to
protect against power failure. Ensure that the cords have a minimum service loop of 6 in. available
and are routed to avoid stress.
2. Power on the power supplies by flipping both switches to the “I” symbol. The power supply LEDs
display amber until POST is complete, and then change to green. The switch usually requires
several minutes to boot and complete POST.
ATTENTION
Power is supplied to the switch as soon as the first power supply is connected and turned on.
3. After POST is complete, verify that the switch power and status LEDs on the left of the port side of
the switch are green. See LED locations on page 30 for the specific location of these LEDs.
Creating a serial connection
You will perform all configuration tasks in this guide using a serial connection.
Complete the following steps to create a serial connection to the switch.
1. Connect the serial cable to the serial port on the switch and to an RS-232 serial port on the
workstation.
If the serial port on the workstation is RJ45 instead of RS-232, remove the adapter on the end of the
serial cable and insert the exposed RJ45 connector into the RJ45 serial port on the workstation.
2. Open a terminal emulator application (such as HyperTerminal on a PC, or TERM, TIP, or Kermit in
a UNIX environment), and configure the application as follows:
• In a Windows environment:
Parameter
Value
Bits per second
9600
Databits
8
Parity
None
Stop bits
1
Flow control
None
• In a UNIX environment using TIP, enter the following string at the prompt:
tip /dev/ttyb -9600.
If ttyb is already in use, use ttya instead and enter the following string at the prompt:
tip /dev/ttya -9600
Switch IP address
You can configure the Brocade 6510 with a static IP address, or you can use a DHCP (Dynamic Host
Configuration Protocol) server to set the IP address of the switch. DHCP is enabled by default. The
Brocade 6510 supports both IPv4 and IPv6.
22
Brocade 6510 Hardware Installation Guide
53-1002174-10
Using DHCP to set the IP address
Using DHCP to set the IP address
When using DHCP, the Brocade 6510 obtains its IP address, subnet mask, and default gateway
address from the DHCP server. The DHCP client can only connect to a DHCP server that is on the
same subnet as the switch. If your DHCP server is not on the same subnet as the Brocade 6510, use a
static IP address.
Setting a static IP address
1. Log into the switch using the default password, which is password.
2. Use the ipaddrset command to set the Ethernet IP address.
If you are going to use an IPv4 IP address , enter the IP address in dotted decimal notation as
prompted. As you enter a value and press Enter for a line in the following example, the next line
appears.
For instance, the Ethernet IP Address appears first. When you enter a new IP address and press
Enter or simply press Enter accept the existing value, the Ethernet Subnetmask line appears.
In addition to the Ethernet IP address itself, you can set the Ethernet subnet mask, the Gateway IP
address, and whether to obtain the IP address via Dynamic Host Control Protocol (DHCP) or not.
switch:admin> ipaddrset
Ethernet IP Address [192.168.74.102]:
Ethernet Subnetmask [255.255.255.0]:
Gateway IP Address [192.168.74.1]:
DHCP [Off]: off
If you are going to use an IPv6 address , enter the network information in semicolon-separated
notation as a standalone command.
switch:admin> i
paddrset -ipv6 --add 1080::8:800:200C:417A/64
IP address is being changed...Done.
Date and time settings
The Brocade 6510 maintains the current date and time inside a battery-backed real-time clock (RTC)
circuit. Date and time are used for logging events. Switch operation does not depend on the date and
time; a Brocade 6510 with an incorrect date and time value still functions properly. However, because
the date and time are used for logging, error detection, and troubleshooting, you should set them
correctly.
Time zones
You can set the time zone for the switch by name. You can also set country, city or time zone
parameters.
If the time zone is not set with the new options, the switch retains the offset time zone settings. The
tsTimeZone command includes an option to revert to the prior time zone format. For more information
about the --old option, see the Brocade 6510.
You can set the time zone for a switch using the tsTimeZone command. The tsTimeZone command
allows you to perform the following tasks:
• Display all of the time zones supported in the firmware
• Set the time zone based on a country and city combination or based on a time zone ID such as PST
The time zone setting has the following characteristics:
Brocade 6510 Hardware Installation Guide
53-1002174-10
23
Local time synchronization
• You can view the time zone settings. However, only those with administrative permissions can set
the time zones.
• The tsTimeZone setting automatically adjusts for Daylight Savings Time.
• Changing the time zone on a switch updates the local time zone setup and is reflected in local time
calculations.
• By default, all switches are in the GMT time zone (0,0). If all switches in a fabric are in one time
zone, it is possible for you to keep the time zone setup at the default setting.
• System services that have already started will reflect the time zone changes only after the next
reboot.
• Time zone settings persist across failover for high availability.
Local time synchronization
You can synchronize the local time of the principal or primary fabric configuration server (FCS) switch
to a maximum of eight external network time protocol (NTP) servers. To keep the time in your SAN
current, it is recommended that the principal or primary FCS switch has its time synchronized with at
least one external NTP server. The other switches in the fabric will automatically take their time from
the principal or primary FCS switch.
All switches in the fabric maintain the current clock server value in non-volatile memory. By default,
this value is the local clock server <LOCL> of the principal or primary FCS switch. Changes to the
clock server value on the principal or primary FCS switch are propagated to all switches in the fabric.
When a new switch enters the fabric, the time server daemon of the principal or primary FCS switch
sends out the addresses of all existing clock servers and the time to the new switch. If a switch with
v5.3.0 or later has entered the fabric it will be able to store the list and the active servers; pre-5.3.0
Fabric OS switches will ignore the new list parameter in the payload and will update only the active
server address.
If the active NTP server configured is IPv6, then distributing the same information in the fabric will not
be possible to switches earlier than v5.3.0 because IPv6 is supported for Fabric OS version 5.3.0 and
later. The default value LOCL will be distributed to pre-5.3.0 switches.
The tsClockServer command accepts multiple server addresses in either IPv4, IPv6, or DNS name
formats. When multiple NTP server addresses are passed, tsClockServer sets the first obtainable
address as the active NTP server. The rest are stored as backup servers that can take over if the
active NTP server fails. The principal or primary FCS switch synchronizes its time with the NTP server
every 64 seconds.
Setting the date
1. Log into the switch using the default password, which is password .
2. Enter the date command , using the following syntax (the double quotation marks are required):
date "mmddHHMMyy"
The values are:
•
•
•
•
•
mm is the month; valid values are 01 through 12.
dd is the date; valid values are 01 through 31.
HH is the hour; valid values are 00 through 23.
MM is minutes; valid values are 00 through 59.
yy is the year; valid values are 00 through 99 (values greater than 69 are interpreted as 1970
through 1999, and values less than 70 are interpreted as 2000-2069).
switch:admin> date
Fri Sep 29 17:01:48 UTC 2007
switch:admin> date "0927123007"
24
Brocade 6510 Hardware Installation Guide
53-1002174-10
Setting time zones
Thu Sep 27 12:30:00 UTC 2007
switch:admin>
Setting time zones
You must perform the procedure on all switches for which the time zone must be set. However, you only
need to set the time zone once on each switch, because the value is written to nonvolatile memory.
Use one of the two following procedures to set the time zone. The first procedure requires you to select
the actual time zone and the second requires you to select the country location of the switch.
The following procedure describes how to set the current time zone using timezone_fmt mode to
Central Standard time.
1. Log into the switch using the default password, which is password.
2. Enter the tsTimeZone command as follows:
switch:admin> tstimezone [--interactive]/ [, timezone_fmt]
Use timezone_fmt to set the time zone by Country/City or by time zone ID, such as PST.
The following example shows how to change the time zone to US/Central.
switch:admin> tstimezone
Time Zone : US/Pacific
switch:admin> tstimezone US/Central
switch:admin> tstimezone
Time Zone : US/Central
The following procedure describes how to set the current time zone using
interactive mode to Pacific Standard Time.
1. Type the tsTimeZone command as follows:
switch:admin> tstimezone --interactive
2. You are prompted to select a general location.
Please identify a location so that time zone rules can be set correctly.
3. Enter the appropriate number or Ctrl-D to quit.
4. At the prompt, select a country location.
5. At the prompt, enter the appropriate number to specify the time zone region or
Ctrl-D to quit.
Synchronizing local time using NTP
Perform the following steps to synchronize the local time using NTP.
1. Log into the switch using the default password, which is password.
2. Enter the tsClockServer command:
switch:admin> tsclockserver "<ntp1;ntp2>"
where ntp1 is the IP address or DNS name of the first NTP server, which the switch must be able to
access. The value ntp2 is the name of the second NTP server and is optional. The entire operand
“<ntp1;ntp2> ” is optional; by default, this value is LOCL, which uses the local clock of the principal or
primary switch as the clock server.
switch:admin>
tsclockserver
LOCL
switch:admin>
tsclockserver "132.163.135.131"
Brocade 6510 Hardware Installation Guide
53-1002174-10
25
Brocade Inter-Switch Link (ISL) Trunking
switch:admin>
tsclockserver
132.163.135.131
switch:admin>
The following example shows how to set up more than one NTP server using a DNS name:
switch:admin>
tsclockserver
"10.32.170.1;10.32.170.2;ntp.localdomain.net"
Updating Clock Server configuration...done.
Updated with the NTP servers
Changes to the clock server value on the principal or primary FCS switch are
propagated to all switches in the fabric.
Brocade Inter-Switch Link (ISL) Trunking
Brocade ISL Trunking is optional software that allows you to create trunking groups of ISLs between
adjacent switches. Up to eight FC ports on the Brocade 6510 can be used as a trunking group to
achieve speeds up to 128 Gbps (256 Gbps full duplex) for optimal bandwidth utilization and load
balancing. For more information about Brocade ISL Trunking, see the Fabric OS Administrator's
Guide.
Fabric OS Native and Access Gateway modes
The Brocade 6510 can function in either Fabric OS Native mode or Brocade Access Gateway mode.
The switch is shipped in Fabric OS Native mode by default.
• You can enable Access Gateway mode using Fabric OS commands or Web Tools.
• All additional POD licenses must be installed before you can enable Access Gateway mode.
• When you enable Access Gateway, you can use the default F_Port-to-N_Port mappings or change
this mapping using command line interface (CLI) or Web Tools, after you configure an IP address
using instructions under Switch IP Address in Chapter 2.
• Access Gateway simplifies SAN deployment by using NPIV. NPIV provides Fibre Channel switch
functions that improve switch scalability, manageability, and interoperability. For more information
on Access Gateway, refer to the following:
‐
‐
‐
For a list of F_Ports mapped to N_Ports by default, refer to Access Gateway default port
mapping on page 27.
For general information and details on using Access Gateway, refer to the Brocade Access
Gateway Administrator’s Guide.
For specific instructions to prepare the edge fabric before connecting it to Access Gateway
(since Access Gateway relies on NPIV technology for its connection to the edge fabric),
refer to the SAN TECH NOTE - Preparing to Install the Brocade Access Gateway) .
NOTE
Access Gateway cannot be connected directly into an array; it requires a fabric to support NPIV.
• Fabric OS features available to the Brocade 6510 depend on whether the switch is configured in
Access Gateway or Fabric OS Native mode. For a list of available features for each mode, refer to
the Brocade Access Gateway Administrator’s Guide.
• In Access Gateway mode, cascading is not available for the Brocade 6510. Refer to the latest
Brocade Access Gateway Administrator’s Guide for details on any other restrictions specific to the
Brocade 6510.
26
Brocade 6510 Hardware Installation Guide
53-1002174-10
Access Gateway default port mapping
• In Fabric OS Native mode, the switch provides up to 48 external Fibre Channel ports. These
universal and self-configuring ports are capable of becoming one of the following port types:
‐
F_Port (fabric enabled)
‐
E_Port (expansion port)
‐
M_Port (mirror port)
• In Access Gateway mode, the switch also provides up to 48 external Fibre Channel ports. However,
these ports are configured as N_Ports, and you cannot reconfigure these as any other port type.
Access Gateway default port mapping
The following table lists the port mappings of F_Ports to N_Ports.
TABLE 2 Access gateway default port mapping
Total ports
F_Ports
N_Ports
Default port mapping
48
0-39
40-47
0-4 mapped to 40
5-9 mapped to 41
10-14 mapped to 42
15-19 mapped to 43
20-24 mapped to 44
25-29 mapped to 45
30-34 mapped to 46
35-39 mapped to 47
Disabling and enabling Access Gateway mode
This section provides steps to disable and enable Access Gateway mode using Fabric OS commands.
For more information on using these commands, refer to the “Enabling and disabling Access Gateway
mode” section in the Access Gateway Administrator's Guide or the Fabric OS Administrator's Guide .
NOTE
You can also disable and enable Access Gateway mode using Web Tools. Refer to the See the Web
Tools Administrator’s Guide for more information.
Enabling Access Gateway mode
Note the following when enabling Access Gateway mode:
• After you enable AG mode, some fabric information is erased, such as the zone and security
databases.
• Enabling AG mode is disruptive because the switch is disabled and rebooted.
• Ensure that no zoning or Admin Domain (AD) transaction buffers are active. If any transaction buffer
is active, enabling Access Gateway mode will fail with the error, “Failed to clear Zoning/Admin
Domain configuration.”
Brocade 6510 Hardware Installation Guide
53-1002174-10
27
Disabling Access Gateway mode
Use the following steps to enable Access Gateway mode using Fabric OS commands. For more
information on enabling Access Gateway mode, refer to “Enabling and disabling Access Gateway
mode” in the Access Gateway Administrator's Guide .
1. Before disabling a switch to enable Access Gateway mode, save the current configuration file using
the configupload command in case you might need this configuration again.
2. Enter the switchshow command to verify the switch mode.
• “Access Gateway Mode” displays for switchMode if the switch is in Access Gateway mode.
• “Native” displays for switchMode if the switch is in Fabric OS Native mode.
3. Enter switchDisable to disable the switch. Access Gateway mode can only be enabled or disabled
when the switch is in a disabled state.
4. Enter ag -modeEnable to enable Access Gateway mode.
5. Enter the ag --modeshow command to verify that AG mode is enabled.
switch:admin>
ag --modeshow
Access Gateway mode is enabled.
Disabling Access Gateway mode
When you disable Access Gateway mode, the switch automatically reboots and comes back online
using the fabric switch configuration. The Access Gateway parameters, such as F_Port-to-N_Port
mapping, Failover, and Failback are automatically removed. When the switch reboots, it starts in
Fabric OS Native mode. To re-join the switch to the core fabric, refer to the Access Gateway
Administrator's Guide .
Use the following steps to disable Access Gateway mode using Fabric OS commands. For more
information, refer to the “Enabling and disabling Access Gateway mode” section in the Access
Gateway Administrator's Guide .
1. Enter the switchshow command to verify the switch mode.
• “Access Gateway Mode” displays if the switch is in Access Gateway mode.
• Interopmode “0” or “Native” displays if the switch is in Fabric OS Native mode.
2. Enter switchDisable to disable the switch. Access Gateway mode can only be disabled or enabled
when the switch is in a disabled state.
3. Enter ag --modeDisable to disable Access Gateway mode.
4. Enter the ag --modeshow command to verify that AG mode is disabled.
switch:admin>
ag --modeshow
Access Gateway mode is NOT enabled
28
Brocade 6510 Hardware Installation Guide
53-1002174-10
Brocade 6510 Operation
● Powering the Brocade 6510 on and off...........................................................................29
● LED activity interpretation............................................................................................... 29
● POST and boot specifications.........................................................................................33
● Interpreting POST results................................................................................................34
● Brocade 6510 Maintenance............................................................................................ 34
● Brocade 6510 Management............................................................................................37
Powering the Brocade 6510 on and off
Complete the following steps to power the Brocade 6510 on.
1. Connect one or both power cords to the power connectors on the power supplies and to a power
source.
2. Set the power switches to “I” .
Power is supplied to the switch as soon as the first power supply is connected and powered on.
The switch runs POST by default each time it is powered on; it can take up to several minutes to boot
and complete POST.
To power the Brocade 6510 off, power off both power supplies by setting each power switch to “O”.
All devices are returned to their initial state the next time the switch is powered on.
NOTE
There is no power on/off switch in the DC FRU. You need to connect/disconnect the power source to
the Brocade 6510 to power on/off.
LED activity interpretation
System activity and status can be determined through the activity of the LEDs on the switch.
There are three possible LED states: no light, a steady light, and a flashing light. Flashing lights may be
slow, fast, or flickering. The lights are green or amber.
Sometimes, the LEDs flash either of the colors during boot, POST, or other diagnostic tests. This is
normal; it does not indicate a problem unless the LEDs do not indicate a healthy state after all boot
processes and diagnostic tests are complete.
Brocade 6510 LEDs
The Brocade 6510 has the following LEDs:
• One system status LED (above) on the left side.
• One power status LED (below) on the left side.
Brocade 6510 Hardware Installation Guide
53-1002174-10
29
LED locations
• Two Ethernet Port LEDs (both green)
• The serial console port LEDs do not light up at any time, even when a cable is inserted and the link
is active.
• One bicolor (green/amber) port status LED for each port on the switch. These LEDs are arrayed
above each pair of Fibre Channel ports.
• One power supply/fan assembly LED on each power supply on the non-port side of the switch
LED locations
The following figure shows the port side of the Brocade 6510. The port status LEDs for the FC ports
are arranged left and right to correspond to the upper and lower ports in each pair. Refer to Port side
of the Brocade 6510 on page 14 for the locations of the FC ports.
FIGURE 5 LEDs on Port Side of Brocade 6510
1.
2.
3.
4.
5.
6.
7.
8.
System power LED
System status LED
Ethernet port activity LED
Ethernet port speed LED
FC port status LED (port 0)
FC port status LED (port 4)
FC port 4
FC port 0
NOTE
The two LEDs on the serial console port are non-functional.
The following figures show the LEDs on the non-port side of the switch.
30
Brocade 6510 Hardware Installation Guide
53-1002174-10
LED patterns
FIGURE 6 LEDs on nonport side of Brocade 6510 with AC power supplies
1. Power supply/fan assembly #2 status LED
2. Power supply/fan assembly #1 status LED
FIGURE 7 LEDs on nonport side of Brocade 6510 with DC power supplies
1. Power supply/fan assembly #2 status LED
2. Power supply/fan assembly #1 status LED
LED patterns
TABLE 3 Port side LED patterns during normal operation
LED name
LED color
Status of hardware
Recommended action
Power Status
No light
System is off or there is an
internal power supply failure.
Verify the system is powered on
(power supply switches to I), the
power cables attached, and your
power source is live.
(green)
The unit may be faulty.
Contact your switch service
provider.
System Status
Steady green
System is on and power
supplies are functioning
properly.
No action required.
No light
System is off or there is no
power.
Verify the system is on and has
completed booting.
Steady green
System is on and functioning
properly.
No action required.
Steady amber
(for more than
five seconds)
A system fault has occurred.
Check the failure indicated on the
system console.
(bicolor - amber/green)
Brocade 6510 Hardware Installation Guide
53-1002174-10
This LED displays steady
amber during POST, this is
Contact your switch service
normal and does not indicate a provider.
fault.
31
Brocade 6510 Operation
TABLE 3 Port side LED patterns during normal operation (Continued)
LED name
Ethernet Speed (green)
Ethernet Activity/Link
(green)
Optical media port
status(one bi-color LED
for each FC port)
LED color
Status of hardware
Recommended action
Blinking amber
Attention is required. A number
of variables can cause this
status including a single power
supply failure, a fan failure, or
one or more environmental
ranges has been exceeded.
Check the management interface
and the error log for details on the
cause of status.
No light
Port speed is 10 Mbps.
No action required.
Steady green
Port speed is 100 Mbps.
No action required.
No light
There is no link.
Verify that the Ethernet cable is
connected correctly.
Steady green
There is a link.
No action required.
Blinking green
There is link activity (traffic).
No action required.
Off
No light or signal carrier on
media interface.
Verify that the transceiver is
installed correctly and that the
cable is connected correctly.
Steady amber
Receiving light or carrier, but
not online.
No action required.
Slow blinking
amber (2 sec)
Disabled (by diagnostics or by
portDisable command).
Verify that the diagnostic tests are
not being run. Reenable the port
using the portEnable command.
Fast blinking
amber (1/2 sec)
Port failure.
Check the management interface
and the error log for details on the
cause of the failure. Contact
Technical Support if necessary.
Steady green
Online.
No action required.
Slow blinking
green (2 sec)
Online but segmented
(loopback cable or
incompatible switch).
No action required.
Fast blinking
green (1/2 sec)
Internal loop-back (diagnostic). No action required.
Flickering green
Online, frames flowing through No action required.
port.
Contact your switch service
provider.
TABLE 4 Nonport side LED patterns during normal operation
32
LED name
LED color
Status of hardware
Recommended action
Power supply/fan
assembly status
No light
PS/fan is not receiving power or
is off.
Verify the PS/fan is on and seated and
the power cord is connected to a
functioning power source.
Brocade 6510 Hardware Installation Guide
53-1002174-10
POST and boot specifications
TABLE 4 Nonport side LED patterns during normal operation (Continued)
LED name
LED color
Status of hardware
Recommended action
Steady green
PS/fan is operating normally.
No action required.
Flashing green PS/fan is faulty.
Note: When the switch is first
powered on the PS/fan status
LED will show flashing green
until POST has completed.
Try the following:
Check the power cable connection.
Verify that the PS/fan is powered on.
Replace the PS/fan FRU.
POST and boot specifications
When the switch is turned on or rebooted, the switch performs POST. Total boot time with POST can be
several minutes. POST can be omitted after subsequent reboots by using the fastboot command or
entering the diagDisablePost command to persistently disable POST.
For more information about these commands, refer to the Fabric OS Command Reference.
POST
The success or failure results of the diagnostic tests that run during POST can be monitored through
LED activity, the error log, or the command line interface.
POST includes the following tasks:
1. Conducts preliminary POST diagnostics.
2. Initializes the operating system.
3. Initializes hardware.
4. Runs diagnostic tests on several functions, including circuitry, port functionality, memory, statistics
counters, and serialization.
Boot
In addition to POST, boot includes the following tasks after POST is complete:
1. Performs universal port configuration.
2. Initializes links.
3. Analyzes fabric. If any ports are connected to other switches, the switch participates in a fabric
configuration.
4. Obtains a domain ID and assigns port addresses.
5. Constructs unicast routing tables.
6. Enables normal port operation.
Brocade 6510 Hardware Installation Guide
53-1002174-10
33
Interpreting POST results
Interpreting POST results
POST is a system check that is performed each time the switch is powered on, rebooted, or reset.
During POST, the LEDs flash either amber or green. Any errors that occur during POST are listed in
the error log.
Complete the following steps to determine whether POST completed successfully and whether any
errors were detected.
1. Verify that the switch LEDs indicate that all components are healthy.
See LED patterns on page 31 for descriptions and interpretations of LED patterns. If one or more
LEDs do not display a healthy state, verify that the LEDs on the switch are not set to “beacon” by
entering the switchShow command to detect if beaconing is active.
2. Verify that the switch prompt displays on the terminal of a computer workstation connected to the
switch.
If there is no switch prompt when POST completes, press Enter. If the switch prompt still does not
display, try opening a Telnet session or accessing the switch through another management tool. If
this is not successful, the switch did not successfully complete POST. Contact your switch supplier
for repair.
3. Review the switch system log for errors. Any errors detected during POST are written to the system
log, accessible through the errShow command .
For information about all referenced commands, and on accessing the error log, refer to the Fabric
OS Administrator's Guide . For information about error messages, refer to the Fabric OS Message
Reference.
Brocade 6510 Maintenance
The Brocade 6510 is designed for high availability and low failure; it does not require any regular
physical maintenance. It includes diagnostic tests and field-replaceable units, described in the
following sections.
Installing an SFP+
The Brocade 6510 only supports Brocade-branded 8 Gbps and 16 Gbps SFP+ optical transceivers.
For the Fibre Channel connections, the Brocade 6510 uses SFP+ transceivers that support any
combination of Short Wavelength (SWL), Long Wavelength (LWL), and Extended Long Wavelength
(ELWL) optical media.
If you use an unqualified transceiver, the switchShow command output shows the port in a Mod_Inv
state. Fabric OS also logs the issue in the system error log.
For this procedure, see the figures in this section.
1. Making sure that the bail (wire handle) is in the unlocked position, position the optical transceiver so
that the key is oriented correctly to the port. Insert the transceiver into the port until it is firmly seated
and the latching mechanism clicks; then close the bail.
The 16 Gbps SFP+ transceivers do not have bails. Use the pull tab on the 16 Gbps SFP+
transceivers to help push the transceiver into the port.
34
Brocade 6510 Hardware Installation Guide
53-1002174-10
Brocade 6510 Operation
Transceivers are keyed so that they can only be inserted with the correct orientation. If a transceiver
does not slide in easily, ensure that it is correctly oriented.
2. Position a cable so that the key (the ridge on one side of the cable connector) is aligned with the slot
in the transceiver. Insert the cable into the transceiver until the latching mechanism clicks.
Cables are keyed so that they can be inserted in only one way. If a cable does not slide in easily,
ensure that it is correctly oriented. Do not insert a cable intended for an mSFP transceiver into a
regular SFP or SFP+ transceiver. You may damage the cable. Do not force a standard SFP-type
cable into an mSFP transceiver. You may damage the transceiver.
NOTE
Each SFP+ has a 10-pad gold-plated PCB-edge connector on the bottom. The correct position to insert
an SFP+ into the upper row of ports is with the gold edge down. The correct position to insert an SFP+
into the lower row of ports is with the gold edge up.
FIGURE 8 Installing a 16 Gbps SFP+ in the upper row of port slot
Brocade 6510 Hardware Installation Guide
53-1002174-10
35
Diagnostic tests
FIGURE 9 Installing an 8 Gbps SFP+ in the upper row of port slot
Diagnostic tests
In addition to POST, Fabric OS includes diagnostic tests to help you troubleshoot the hardware and
firmware. This includes tests of internal connections and circuitry, fixed media, and the transceivers
and cables in use.
The tests are implemented by command, either through a Telnet session or through a console set up
to the serial connection to the switch. Some tests require the ports to be connected by external cables,
to allow diagnostics to verify the serializer/deserializer interface, transceiver, and cable. Some tests
require loopback plugs.
Diagnostic tests run at link speeds of 2, 4, 8, 10, or 16 Gbps (FC) depending on the speed of the link
being tested and the type of port.
NOTE
Diagnostic tests might temporarily lock the transmit and receive speed of the links during diagnostic
testing.
For information about specific diagnostic tests, see the Fabric OS Troubleshooting and Diagnostics
Guide.
36
Brocade 6510 Hardware Installation Guide
53-1002174-10
Brocade 6510 Management
Brocade 6510 Management
You can use the management functions built into the Brocade 6510 to monitor the fabric topology, port
status, physical status, and other information to help you analyze switch performance and to accelerate
system debugging.
The Brocade 6510 automatically performs power-on self-test (POST) each time it is turned on. Any
errors are recorded in the system error log. For more information about POST, see POST and boot
specifications on page 33.
For information about upgrading the version of Fabric OS installed on your switch, see the Fabric OS
Administrator's Guide.
You can manage the Brocade 6510 using any of the management options listed in the following table.
Please refer to the Fabric OS Command Reference for more information on the CLI commands.
TABLE 5 Management Options for the Brocade 6510 Switch
Management Tool
Out-of-band Support
In-band Support
Command line interface (CLI)
Ethernet or serial
connection
IP over Fibre Channel
Ethernet or serial
connection
IP over Fibre Channel
Ethernet or serial
connection
IP over Fibre Channel
Ethernet or serial
connection
Native in-band interface(over
HBA only)
Ethernet or serial
connection
IP over Fibre Channel
Up to two admin sessions and four user sessions
simultaneously. For more information, refer to the Fabric
OS Administrator’s Guide and the Fabric OS Command
Reference Manual.
Brocade Web Tools
For information, refer to the Web Tools Administrator’s
Guide.
Standard SNMP applications
For information, refer to the MIB Reference Manual.
Management Server
For information, refer to the Fabric OS Administrator’s
Guide and the Fabric OS Command Reference Manual.
Brocade Network Advisor (option to purchase)
For information, refer to the Brocade Network Advisor
documentation set.
Brocade 6510 Hardware Installation Guide
53-1002174-10
37
Brocade 6510 Management
38
Brocade 6510 Hardware Installation Guide
53-1002174-10
Power supply, fan assembly, and airflow direction support
matrix
The power supply and fan assembly units are identified by the following airflow directions:
• Intake FRU with an orange "I" label or without any label: Pulls air from the non-port side of the
switch and exhausts it out the port side.
These units are also identified as/by:
•
Port-side air exhaust
•
Nonport-side air intake
•
Back-to-front (nonport-side to port-side) airflow
•
Fan direction is shown as "Reverse" airflow in the
chassisShow command output
•
Part numbers ending with -R
• Exhaust FRU with a green "E" label: Pulls air from the port side of the switch and exhausts it out
the non-port side.
These units are also identified as/by:
•
Port-side air intake
•
Nonport-side air exhaust
•
Front-to-back (port-side to nonport-side) airflow
•
Fan direction is shown as "Forward" airflow in the
chassisShow command output
•
Part numbers ending with -F
The AC powers supplies, fan assemblies, and airflow directions are supported as per the following
table:
Platform
Combined AC PSU and fans
Shipping FRU
configuration per
chassis
Intake FRU
Labeled
Exhaust FRU
Labeled
Brocade 5100
2
23-0000092-xx
No
NA
-
Brocade 6505
1
23-0000092-xx
No
NA
-
Brocade 6510
2
23-0000092-xx
No
23-0000113-xx
"E"
Brocade 7800
2
23-0000092-xx
No
NA
-
Brocade VA-40FC
2
23-0000092-xx
No
23-1000032-xx
"E"
Brocade 6510 Hardware Installation Guide
53-1002174-10
39
Power supply, fan assembly, and airflow direction support matrix
NOTE
NA = Hardware is not available and not supported in the current release.
The DC powers supplies, fan assemblies, and airflow directions are supported as per the following
table:
Platform
Combined DC PSU and fans
Shipping FRU
configuration per
Intake FRU
chassis
Labeled
Intake FRU
Labeled
Brocade 5100
2
NA
-
NA
-
Brocade 6505
1
NA
-
NA
-
Brocade 6510
2
23-0000112-xx
"I"
NA
-
Brocade 7800
2
NA
-
NA
-
Brocade VA-40FC
2
NA
-
NA
-
NOTE
NA = Hardware is not available and not supported in the current release.
40
Brocade 6510 Hardware Installation Guide
53-1002174-10
Removal and replacement of power supplies and fans
● Introduction..................................................................................................................... 41
● Removing and replacing a power supply and fan assembly........................................... 42
Introduction
NOTE
Read the Installation and safety considerations on page 17 before servicing.
The field replaceable units (FRUs) in the Brocade 6510 can be removed and replaced without special
tools. The Brocade 6510 can continue operating during the FRU replacement if the conditions specified
in the procedure are followed.
The Brocade 6510 supports the following types of power supplies.
• AC power supply with port-side air intake (exhaust FRU). This unit moves the air from the port side to
the nonport side of the switch.
• AC power supply with port-side air exhaust (intake FRU). This unit moves the air from the nonport
side to the port side of the switch.
• DC power supply with port-side air exhaust (intake FRU). The DC power supplies function the same
way as AC power supplies except for the following points:
‐
‐
‐
‐
‐
‐
‐
The handle is on top and the power supply connector is below.
There is no on/off switch in the power supply.
The cable and the connector are different from the AC power supplies.
The pin outs on the DC power supply connector from left to right are +, -, and gnd. The plug
has a polarity label.
The power supply LED interpretations are same as AC power supply.
The DC-DC power cord is thicker and heavier than the AC power cords. Hence, ensure that
the screws on the plug are used to tighten and hold the power cable to connector on the
power supply firmly.
The DC port-side air exhaust (intake FRU) model has a different part number and has an
orange arrow with 'I' label on the top right corner of the non-port side as well as on top of the
FRU, similar to the AC intake FRU.
NOTE
The two FRU assemblies concurrently installed in the chassis must be of the same type (AC or DC),
model (airflow direction), and part number. If the airflow directions are different, an error is generated on
the console. The two power supply and fan assembly FRU units are hot-swappable if they are replaced
one at a time. They are identical and fit into either slot.
The Brocade 6510 fans are fixed inside the combined power supply and fan FRU to provide necessary
airflow to cool the whole system. There are two fans located in each FRU. The system software sets fan
speed and measures their speeds through the tachometer interface.
Brocade 6510 Hardware Installation Guide
53-1002174-10
41
Removing and replacing a power supply and fan assembly
Removing and replacing a power supply and fan assembly
This section describes how to change field replaceable units (FRUs). You must replace a failed FRU
with a FRU of the same type. A new FRU must have the same part number (P/N) as the FRU being
replaced. The manufacturing P/N is located on the top of the FRU. The two FRU assemblies
concurrently installed in the chassis must be of the same type (AC or DC), model (airflow direction),
and must have the same part number. If a mismatched airflow model is installed by mistake, a warning
is sent to the console. The warning messages will be similar to the following: For a power supply or
combined power supply/fan mismatch - [WARNING, BR6510, MISMATCH in PSU-FAN FRUS Air
Flow direction. Replace PSU with fan air flows in same direction.
CAUTION
Ensure that the airflow direction of the power supply unit matches that of the installed fan tray.
The power supplies and fan trays are clearly labeled with either a green arrow with an "E", or
an orange arrow with an "I."
You can use an external label or lack thereof as a guide. The exhaust FRUs are labeled with an
airflow symbol on the faceplate to indicate that the assembly exhausts air. The symbol also appears
on the top of the FRU. All FRUs in a chassis must be of the same type so that airflow direction is
consistent.
See the following two switch samples for the Fan Direction values in the chassisShow outputs.
ras222:FID128:root> chassisshow
FAN Unit: 1
Fan Direction: Reverse
Time Awake: 0 days
FAN Unit: 2
Fan Direction: Reverse
Time Awake: 0 days
POWER SUPPLY Unit: 1
Power Source: DC
Time Awake: 0 days
(output truncated)
ras223:FID128:root> chassisshow
FAN Unit: 1
Fan Direction: Forward
Time Awake: 0 days
FAN Unit: 2
Fan Direction: Forward
Time Awake: 0 days
POWER SUPPLY Unit: 1
Power Source: AC
Time Awake: 0 days
(output truncated)
The Brocade 6510 has two power supply and fan assemblies, as displayed in the following figure.
Fabric OS identifies the assemblies from right to left on the nonport side as assembly 1 and assembly
2. (The actual appearance of the Brocade 6510 may differ slightly from this illustration but the
locations are correct.)
42
Brocade 6510 Hardware Installation Guide
53-1002174-10
Removal and replacement of power supplies and fans
FIGURE 10 Exhaust Airflow labels on the AC power supply FRUs
1.
2.
3.
4.
5.
6.
7.
8.
Power supply/fan assembly #2
Airflow label ("E" indicates nonport-side exhaust units)
Power supply/fan assembly #1
Power supply/fan assembly LED
On/off switch
AC Power plug receptacle (with plug retainer)
Thumbscrew
Handle
FIGURE 11 Intake Airflow labels on the DC power supply FRUs
1.
2.
3.
4.
5.
6.
7.
Power supply/fan assembly #2
Airflow label ( " I " indicates port side exhaust units)
Power supply/fan assembly #1
Handle
Thumbscrew
DC Power plug receptacle (with cable retainer screws)
Power supply/fan assembly LED
The following figure illustrates how to fasten the cables to the DC cable receptacles using the screws:
Brocade 6510 Hardware Installation Guide
53-1002174-10
43
Removal and replacement of power supplies and fans
FIGURE 12 DC power connector and cable receptacle with cable retainer screws
1. Cables
2. Fastening screws
Switch power supply and fan assemblies on the non-port side
• Disassembling any part of the power supply voids the part warranty and regulatory certifications.
There are no user-serviceable parts inside the power supply and fan assembly.
CAUTION
Changes or modifications made to this device that are not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
• The cooling system relies on pressurized air, do not leave either of the power supply and fan
assembly slots empty longer than two minutes when the Brocade 6510 is operating.
CAUTION
If you do not install a module or a power supply in a slot, you must keep the slot filler panel
in place. If you run the chassis with an uncovered slot, the system will overheat.
NOTE
If a power supply and fan assembly fails, leave the power supply and fan assembly in the Brocade
6510 until it can be replaced. Maintain both power supply and fan assembly in operational condition to
provide redundancy.
The following table describes the power supply and fan assembly status LED colors, behaviors, and
actions required, if any.
TABLE 6 Power supply and fan assembly status LED behavior, description, and required actions
44
LED Color
Description
Action Required
No light
Power supply and fan assembly is not receiving
power, or is off.
Verify that the power supply and fan
assembly is on and seated and the
power cord is connected to a
functioning power source.
Brocade 6510 Hardware Installation Guide
53-1002174-10
Determining the need to replace a power supply and fan assembly
TABLE 6 Power supply and fan assembly status LED behavior, description, and required actions
(Continued)
LED Color
Description
Action Required
Steady green
Power supply and fan assembly is operating
normally.
No action is required.
Flashing green (for Power supply and fan assembly is faulty for one of
more than 5
the following reasons:
seconds)
• The assembly is switched off - flashing for ~ 5
seconds, then off
• The power cable is disconnected - flashing for ~
5 seconds, then off
Try one of the following:
•
Check the power cable connection.
•
Verify that the assembly is
powered on
•
Replace the power supply and fan
assembly FRU.
• The power supply and fan assembly has failed
NOTE: When the Brocade 6510 is first powered on,
the power supply and fan assembly status LED will
show flashing until POST has completed.
Determining the need to replace a power supply and fan assembly
Use one of the following methods to determine the status of the power supplies:
• Check the power supply and fan assembly status LED next to the On/Off switch (see LED locations
on page 30)
• In Web Tools, click the Power Status icon.
• Enter the psShow command at the prompt to display power supply and fan assembly status as
shown below:
br6510:admin> psshow
Power Supply #1 is OK
V10529,
TQ2H0000030
Power Supply #2 is OK
V10541,
TQ2H0000189
br6510:admin>
,60-0300031-01,X2,
,SP640
,2X,TQ2H0000
,60-0300031-01,X3,
,SP640-2P
,A ,TQ2H0000
Time Required
Replacing a power supply and fan assembly in the Brocade 6510 should require less than two minutes
to complete.
Items Required
The following items are required to replace a power supply and fan assembly:
• New power supply and fan assembly (must have the same airflow as the FRU being replaced)
• Phillips-head screwdriver #1
Brocade 6510 Hardware Installation Guide
53-1002174-10
45
Removing a power supply and fan assembly
Removing a power supply and fan assembly
Complete the following steps to remove a combined power supply and fan assembly from a Brocade
6510.
1. To leave the Brocade 6510 in service while replacing a power supply and fan assembly, verify that
the other power supply and fan assembly (the one not being replaced) has been powered on for at
least four seconds and has a steady green LED.
2. Power off the power supply to be replaced by pressing the AC power switch to the O symbol. The
fans in the other power supply will automatically switch to high speed to maintain adequate cooling.
3. Unplug the power cord from the power supply and fan assembly that is being replaced.
4. Using a Phillips-head screwdriver, unscrew the captive screw.
5. Remove the power supply and fan assembly from the chassis by pulling the handle out and away
from the chassis.
6. Note the part number and airflow label (or lack thereof) on the assembly just removed.
FIGURE 13 Inserting the AC power supply and fan assembly in the switch
1.
2.
3.
4.
46
Brocade 6510 chassis
AC power supply and fan assembly
Captive screw
Product and airflow labels (port-side air intake/forward airflow)
Brocade 6510 Hardware Installation Guide
53-1002174-10
Replacing a power supply and fan assembly
FIGURE 14 Inserting the DC power supply and fan assembly in the switch
1.
2.
3.
4.
Brocade 6510 chassis
DC power supply and fan assembly
Product and airflow labels (port-side air exhaust/reverse airflow)
Captive screw
Replacing a power supply and fan assembly
Complete the following steps to replace a combined power supply and fan assembly in a Brocade 6510.
CAUTION
The power supply switch must be in the off position when you insert the power supply into the
chassis. Damage to the switch can result if a live power supply is installed.
1. Ensure that the new power supply and fan assembly has the same part number and airflow label (or
lack thereof) as the power supply and fan assembly being replaced.
CAUTION
Ensure that the airflow direction of the power supply unit matches that of the installed fan
tray. The power supplies and fan trays are clearly labeled with either a green arrow with an
"E", or an orange arrow with an "I."
2. Orient the new power supply and fan assembly with the captive screw on the right, as shown in the
figure.
Do not force the installation. If the FRU does not slide in easily, ensure that it is correctly oriented
before continuing.
CAUTION
Carefully follow the mechanical guides on each side of the power supply slot and make sure
the power supply is properly inserted in the guides. Never insert the power supply upside
down.
3. Gently push the power supply and fan assembly into the chassis until it is firmly seated.
4. Using the Phillips screwdriver, secure the power supply and fan assembly to the chassis by
tightening in the captive screw.
5. Plug the power cord in to the power supply and fan assembly and power on the unit by pressing the
AC power switch to the I symbol.
Brocade 6510 Hardware Installation Guide
53-1002174-10
47
Removal and replacement of power supplies and fans
6. Verify that the LED on the new power supply and fan assembly displays a steady green light while
the Brocade 6510 is operating. If the LED is not a steady green, ensure that the power supply is
securely installed and seated properly.
7. Optionally, if using the Command Line Interface (CLI), enter the psShow command at the
command line prompt to display the status. Power supply and fan assembly status can also be
viewed using the Web Tools application.
48
Brocade 6510 Hardware Installation Guide
53-1002174-10
Brocade 6510 Switch Technical Specifications
This document highlights the features and specifications for the Brocade 6510 switch.
System specifications
System component
Description
Enclosure
1U, non-port side front-to-back exhaust airflow, power from back
Power inlet
C14
Power supplies
Dual, hot-swappable redundant power supplies with integrated system cooling fans
Fans
Two fans per FRU
Cooling
Port side to the non-port side of the switch (non-port side exhaust) and non-port side
to the port side (port side exhaust)
System architecture
Nonblocking shared memory switch
System processors
PowerPC 440EPx @ 667 MHz
Port-to-port latency
<700 nanoseconds with no contention (destination port is free)
Fibre Channel
System component
Description
Fibre Channel ports
SFP+ optical transceivers that support any combination of Short Wavelength (SWL)
and Long Wavelength (LWL) or Extended Long Wavelength (ELWL) optical media
among the switch ports.
Capable of operating at 2, 4, 8, or 16 Gbps depending on SFP+ models and able to
auto-negotiate to the maximum link speed.
•
2, 4, and 8 Gbps performance is enabled by 8 Gbps SFP+ transceivers.
• 4, 8, and 16 Gbps performance is enabled by 16 Gbps SFP+ transceivers.
ANSI Fibre Channel
protocol
FC-PH (Fibre Channel Physical and Signaling Interface standard)
Modes of operation
Fibre Channel Class 2 and Class 3
Fabric initialization
Complies with FC-SW-3 Rev. 6.6
Brocade 6510 Hardware Installation Guide
53-1002174-10
49
Brocade 6510 Switch Technical Specifications
System component
Description
FCIP (IP over Fibre
Channel)
Complies with FC-IP 2.3 of FCA profile
Port Status
Bicolor LED (amber/green)
System component
Description
SFP GbE ports
10/100 Mbps Ethernet (24, 36, and 48 ports)
Ethernet
Ethernet management port RJ-45
LEDs
System component
Description
System power LED
One power status LED (below) on the left side.
System status LED
One system status LED (above) on the left side.
Ethernet port activity LED
One Ethernet port activity LED on the left side.
Ethernet port speed LED
One Ethernet port speed LED on the left side.
Serial console port LED
The serial console port LEDs do not light up at any time, even when a cable is
inserted and the link is active.
FC port status LED
One bicolor (green/amber) port status LED for each port on the switch.
Fan assembly LED
One power supply/fan assembly LED above the AC power switch on each power
supply on the non-port side of the switch.
System component
Description
Serial cable
RJ-45 console cable
RJ-45 to DB9 adapter
RJ-45 to DB9 for console cable
RJ-45 connector
Uses an RJ-45 connector for the serial port
Other
50
Brocade 6510 Hardware Installation Guide
53-1002174-10
Brocade 6510 Switch Technical Specifications
Weight and physical dimensions
"System weight"Brocade 6510 switch: 9.16 kg (20.20 lb) with two power supply and fan assemblies,
and no SFPs installed).
Model
Height
Width
Depth
Weight (empty)
Weight (fully
loaded)
Brocade 6510
switch
4.30 cm
43.80 cm
44.30 cm
9.16 kg
N/A
1.70 inches
17.20 inches
17.40 inches
20.20 lb
Environmental requirements
Condition
Operational
Non-operational
Ambient temperature
0°C to 40°C (32°F to 104°F)
-25°C to 70°C (-13°F to 158°F)
Relative humidity
(non-condensing)
10% to 85% at 40°C (104°F)
10% to 95% at 70°C (158°F)
Altitude (above sea
level
0 to 3000 m (9,842 feet)
0 to 12000 m (39,370 feet)
Shock
20 G, 6 ms, half-sine wave
33 G, 11 ms, half-sine wave, 3/eg Axis
Vibration
0.5 G sine, 0.4 gms random, 5-500 Hz
2.0 G sine, 1.1 gms random, 5-500 Hz
Airflow
Maximum: 71.36 cmh (42 cfm)
N/A
Nominal: 59.47 cmh (35 cfm)
Heat dissipation
375 BTU/hr
N/A
Operating noise
70 dB
N/A
Power supply specifications (per PSU)
Power supply Maximum
model
output power
rating (DC)
Input voltage
XBR-5100-000 150 W
1
100 - 240 VAC 50/60 Hz
(nominal)
(nominal)
85 - 264 VAC
(range)
Brocade 6510 Hardware Installation Guide
53-1002174-10
Input line
frequency
47 - 63 Hz
(range)
Maximum
input current
Input line
protection
Maximum
inrush
current
2.5 A
Line & Neutral
Fused
50 A peak @
240 VAC for
<10 ms, 10 ms
- 150 ms, <15
A peak
51
Brocade 6510 Switch Technical Specifications
Power supply Maximum
model
output power
rating (DC)
Input voltage
XBR-6510-000 150 W
1
100 - 240 VAC 50/60 Hz
(nominal)
(nominal)
XBR-6510DC0002
150 W
Input line
frequency
85 - 264 VAC
(range)
47 - 63 Hz
(range)
48 VDC
(nominal)
N/A
Maximum
input current
Input line
protection
Maximum
inrush
current
2.5 A
Line & Neutral
Fused
50 A peak @
240 VAC for
<10 ms, 10 ms
- 150 ms,
<15A peak
4.5 A
-Ve & +Ve
40 A peak for
<10 ms
40 VDC- 60
VDC (range)
Power consumption (typical configuration)
NOTE
A 200 VAC power supply is not supported on the Brocade 6510 switch.
52
Model name
@100 VAC input @200 VAC input @-48 VDC input Minimum
number of
power supplies
Notes
Brocade 6510
switch
110 W
Fully configure
all ports with
approved 16
Gbps SW optic
sources and
loopback.
Operate tests at
maximum 16
Gbps port speed
and fans at
nominal speed.
375.44 BTU/hr
N/A
112 W
382.26 BTU/hr
1
Brocade 6510 Hardware Installation Guide
53-1002174-10
Brocade 6510 Switch Technical Specifications
Power consumption (maximum configuration)
Model name
@100 VAC input @200 VAC input @-48 VDC input
Minimum
number of
power supplies
Notes
Brocade 6510
switch
123 W
1
Fully configure all
ports with MSA
optic maximum
wattage rating.
Fans at high
speed.
N/A
123 W
419.81 BTU/hr
419.81 BTU/hr
Power consumption (idle configuration)
NOTE
A 200 VAC power supply is not supported on the Brocade 6510 switch.
Model name
@100 VAC input @200 VAC input @-48 VDC input
Minimum
number of
power supplies
Notes
Brocade 6510
switch
72 W
1
No optics or
connections to
ports installed
and system
booted up. Fans
at nominal
speed.
N/A
53 W
245.74 BTU/hr
180.89 BTU/hr
Data port specifications (Fibre Channel)
Name
Number
Description
Brocade 6510
switch
48
F_Ports: 0-39
N_Ports: 40-47
Fibre Channel data transmission ranges
Port speed (Gbps)
Cable size
(microns)
Short wavelength
(SWL)
Long wavelength
(LWL)
Extended long
wavelength (ELWL)
2
50
300 m (984 ft) (OM2)
N/A
N/A
500 m (1,640 ft)
(OM3)
Brocade 6510 Hardware Installation Guide
53-1002174-10
53
Brocade 6510 Switch Technical Specifications
Port speed (Gbps)
4
Cable size
(microns)
Short wavelength
(SWL)
Long wavelength
(LWL)
Extended long
wavelength (ELWL)
62.5
150 m (492 ft)
N/A
N/A
9
N/A
30 km (18.6 miles)
N/A
50
150 m (492 ft) (OM2)
N/A
N/A
380 m (1,264 ft)
(OM3)
400 m (1,312 ft)
(OM4)
8
62.5
70 m (229 ft)
N/A
N/A
9
N/A
30 km (18.6 miles)
N/A
50
50 m (164 ft) (OM2)
N/A
N/A
150 m (492 ft) (OM3)
150 m (492 ft) (OM4)
10
62.5
21 m (68 ft)
N/A
N/A
9
N/A
10 km (6.2 miles)
N/A
50
82 m (269 ft) (OM2)
N/A
N/A
300 m (984 ft) (OM3)
550 m (1,804 ft)
(OM4)
16
62.5
33 m (108 ft)
N/A
N/A
9
N/A
10 km (6.2 miles)
N/A
50
35 m (115 ft) (OM2)
N/A
N/A
100 m (328 ft) (OM3)
125 m (410 ft) (OM4)
54
62.5
15 m (49 ft)
N/A
N/A
9
N/A
10 km (6.2 miles)
N/A
Brocade 6510 Hardware Installation Guide
53-1002174-10
Brocade 6510 Switch Technical Specifications
Serial port specifications (pinout RJ-45)
Pin
Signal
Description
1
Not supported
N/A
2
Not supported
N/A
3
UART1_TXD
Transmit data
4
GND
Logic ground
5
GND
Logic ground
6
UART1_RXD
Receive data
7
Not supported
N/A
8
Not supported
N/A
Serial port specifications (protocol)
Parameter
Value
Baud
9600
Data bits
8
Parity
None
Flow control
None
Stop bits
1
Memory specifications
Memory
Type
Size
Main Memory
DDR2 SDRAM
1 GB, 64-bit with 8-bit ECC
Boot Flash
-
4 MB
Compact Flash
-
1 GB
Brocade 6510 Hardware Installation Guide
53-1002174-10
55
Brocade 6510 Switch Technical Specifications
Regulatory compliance (EMC)
•
•
•
•
•
•
•
•
•
FCC Part 15, Subpart B (Class A)
EN 55022 (CE mark) (Class A)
EN 55024 (CE mark) (Immunity) for Information Technology Equipment
ICES-003 (Canada) (Class A)
AS/NZ 55022 (Australia) (Class A)
VCCI (Japan) (Class A)
EN 61000-3-2
EN 61000-3-3
EN 61000-6-1
Regulatory compliance (safety)
• CAN/CSA-C22.2 No. 60950-1-07/UL60950-1 - Safety of Information Technology Equipment
• EN 60825-1 Safety of Laser Products - Part 1: Equipment Classification, Requirements and User's
Guide
• EN 60825-2 Safety of Laser Products - Part 2: Safety of Optical Fibre Communications Systems
• EN 60950-1, IEC 60950-1 Safety of Information Technology Equipment
Regulatory compliance (environmental)
• 2011/65/EU - Restriction of the use of certain hazardous substance in electrical and electronic
equipment (EU RoHS)
• 2012/19/EU - Waste electrical and electronic equipment (EU WEEE)
• 94/62/EC - packaging and packaging waste (EU)
• 2006/66/EC - batteries and accumulators and waste batteries and accumulators (EU battery
directive)
• 1907/2006 of the European Parliament and of the Council of 18 December 2006 concerning the
Registration, Evaluation, Authorisation and Restriction of Chemicals (EU REACH)
• Section 1502 of the Dodd-Frank Wall Street Reform and Consumer Protection Act of 2010 - U.S.
Conflict Minerals
• 30/2011/TT-BCT - Vietnam circular.
• SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in EIPs
(China)
• SJ/T 11364-2006 Marking for the Control of Pollution Caused by EIPs (China)
• NEBS-compliant
56
Brocade 6510 Hardware Installation Guide
53-1002174-10
Regulatory Statements
● BSMI statement (Taiwan)................................................................................................57
● Canadian requirements...................................................................................................57
● CE Statement..................................................................................................................57
● China CC statement........................................................................................................58
● China ROHS................................................................................................................... 59
● FCC warning (US only)................................................................................................... 59
● Germany......................................................................................................................... 59
● KCC statement (Republic of Korea)................................................................................59
● VCCI statement...............................................................................................................59
BSMI statement (Taiwan)
Warning:
This is Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Canadian requirements
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations, ICES-003 Class A.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
CE Statement
ATTENTION
This is a Class A product. In a domestic environment, this product might cause radio interference, and
the user might be required to take corrective measures.
The standards compliance label on this device contains the CE mark which indicates that this system
conforms to the provisions of the following European Council directives, laws, and standards:
Brocade 6510 Hardware Installation Guide
53-1002174-10
57
China CC statement
• Electromagnetic Compatibility (EMC) Directive 2004/108/EEC
• Low Voltage Directive (LVD) 2006/95/EC
• EN50082-2/EN55024:1998 (European Immunity Requirements)
‐
‐
EN61000-3-2/JEIDA (European and Japanese Harmonics Spec)
EN61000-3-3
China CC statement
58
Brocade 6510 Hardware Installation Guide
53-1002174-10
China ROHS
China ROHS
Refer to the latest revision of the China ROHS document (P/N 53‐1000428‐xx) which ships with the
product.
FCC warning (US only)
This equipment has been tested and complies with the limits for a Class A computing device pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used
in accordance with the instruction manual, might cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case
the user will be required to correct the interference at the user’s own expense.
Germany
Machine noise information regulation - 3. GPSGV, the highest sound pressure level value is 70.0 dB(A)
in accordance with EN ISO 7779.
Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste Schalldruckpegel beträgt 70.0 dB(A)
gemäss EN ISO 7779.
KCC statement (Republic of Korea)
Class A device (Broadcasting Communication Device for Office Use): This device obtained EMC
registration for office use (Class A), and may be used in places other than home. Sellers and/or users
need to take note of this.
VCCI statement
Brocade 6510 Hardware Installation Guide
53-1002174-10
59
Regulatory Statements
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio
disturbance might arise. When such trouble occurs, the user might be required to take corrective
actions.
60
Brocade 6510 Hardware Installation Guide
53-1002174-10
Caution and Danger Notices
● Cautions.......................................................................................................................... 61
● Danger Notices............................................................................................................... 64
Cautions
A caution calls your attention to a possible hazard that can damage equipment.
"Vorsicht" weist auf die Gefahr einer möglichen Beschädigung des Gerätes hin.
Une mise en garde attire votre attention sur un risque possible d'endommagement de l'équipement. Cidessous, vous trouverez les mises en garde utilisées dans ce manuel.
Un mensaje de precaución le advierte sobre un posible peligro que pueda dañar el equipo. Las
siguientes son precauciones utilizadas en este manual.
General cautions
CAUTION
Do not install the device in an environment where the operating ambient temperature might
exceed 40°C (104°F).
VORSICHT
Das Gerät darf nicht in einer Umgebung mit einer Umgebungsbetriebstemperatur von über
40°C (104°F) installiert werden.
MISE EN
GARDE
N'installez pas le dispositif dans un environnement où la température d'exploitation ambiante
risque de dépasser 40°C (104°F).
PRECAUCIÓN
No instale el instrumento en un entorno en el que la temperatura ambiente de operación pueda
exceder los 40°C (104°F).
CAUTION
Make sure the airflow around the front, sides, and back of the device is not restricted.
VORSICHT
Stellen Sie sicher, dass an der Vorderseite, den Seiten und an der Rückseite der Luftstrom
nicht behindert wird.
MISE EN
GARDE
Vérifiez que rien ne restreint la circulation d'air devant, derrière et sur les côtés du dispositif et
qu'elle peut se faire librement.
PRECAUCIÓN
Asegúrese de que el flujo de aire en las inmediaciones de las partes anterior, laterales y
posterior del instrumento no esté restringido.
Brocade 6510 Hardware Installation Guide
53-1002174-10
61
Caution and Danger Notices
CAUTION
Ensure that the airflow direction of the power supply unit matches that of the installed fan tray.
The power supplies and fan trays are clearly labeled with either a green arrow with an "E", or
an orange arrow with an "I."
VORSICHT
Vergewissern Sie sich bei den ICX 6610-Geräten, dass die Luftstromrichtung des Netzteils der
der eingebauten Lüftereinheit entspricht. Die Netzteile und Lüftereinheiten sind eindeutig mit
einem grünen Pfeil und dem Buchstaben "E" oder einem orangefarbenen Pfeil mit dem
Buchstaben "I" gekennzeichnet.
MISE EN
GARDE
Pour les équipements de type ICX 6610, veillez à ce que le sens de circulation de l'air du bloc
d'alimentation corresponde à celui du tiroir de ventilation installé. Les blocs d'alimentation et
les tiroirs de ventilation sont étiquetés d'une flèche verte avec un "E " ou d'une flèche orange
avec un " I ".
PRECAUCIÓN
En el caso de dispositivos ICX 6610, asegúrese de que la dirección del flujo de aire de la
unidad de alimentación se corresponda con la de la bandeja del ventilador instalada. Los
dispositivos de alimentación y las bandejas del ventilador están etiquetadas claramente con
una flecha verde y una "E" o con una flecha naranja y una "I".
CAUTION
Changes or modifications made to this device that are not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
VORSICHT
Falls dieses Gerät verändert oder modifiziert wird, ohne die ausdrückliche Genehmigung der
für die Einhaltung der Anforderungen verantwortlichen Partei einzuholen, kann dem Benutzer
der weitere Betrieb des Gerätes untersagt werden.
MISE EN
GARDE
Les éventuelles modifications apportées à cet équipement sans avoir été expressément
approuvées par la partie responsable d'en évaluer la conformité sont susceptibles d'annuler le
droit de l'utilisateur à utiliser cet équipement.
PRECAUCIÓN
Si se realizan cambios o modificaciones en este dispositivo sin la autorización expresa de la
parte responsable del cumplimiento de las normas, la licencia del usuario para operar este
equipo puede quedar anulada.
Electrical cautions
CAUTION
Before plugging a cable into to any port, be sure to discharge the voltage stored on the cable
by touching the electrical contacts to ground surface.
VORSICHT
62
Bevor Sie ein Kabel in einen Anschluss einstecken, entladen Sie jegliche im Kabel
vorhandene elektrische Spannung, indem Sie mit den elektrischen Kontakten eine geerdete
Oberfläche berühren.
Brocade 6510 Hardware Installation Guide
53-1002174-10
Caution and Danger Notices
MISE EN
GARDE
Avant de brancher un câble à un port, assurez-vous de décharger la tension du câble en
reliant les contacts électriques à la terre.
PRECAUCIÓN
Antes de conectar un cable en cualquier puerto, asegúrese de descargar la tensión
acumulada en el cable tocando la superficie de conexión a tierra con los contactos eléctricos.
CAUTION
Static electricity can damage the chassis and other electronic devices. To avoid damage, keep
static-sensitive devices in their static-protective packages until you are ready to install them.
VORSICHT
Statische Elektrizität kann das System und andere elektronische Geräte beschädigen. Um
Schäden zu vermeiden, entnehmen Sie elektrostatisch empfindliche Geräte erst aus deren
antistatischer Schutzhülle, wenn Sie bereit für den Einbau sind.
MISE EN
GARDE
L'électricité statique peut endommager le châssis et les autres appareils électroniques. Pour
éviter tout dommage, conservez les appareils sensibles à l'électricité statique dans leur
emballage protecteur tant qu'ils n'ont pas été installés.
PRECAUCIÓN
La electricidad estática puede dañar el chasis y otros dispositivos electrónicos. A fin de impedir
que se produzcan daños, conserve los dispositivos susceptibles de dañarse con la electricidad
estática dentro de los paquetes protectores hasta que esté listo para instalarlos.
CAUTION
If you do not install a module or a power supply in a slot, you must keep the slot filler panel in
place. If you run the chassis with an uncovered slot, the system will overheat.
VORSICHT
Falls kein Modul oder Netzteil im Steckplatz installiert wird, muss die Steckplatztafel angebracht
werden. Wenn ein Steckplatz nicht abgedeckt wird, läuft das System heiß.
MISE EN
GARDE
Si vous n’installez pas de module ou de bloc d'alimentation dans un slot, vous devez laisser le
panneau du slot en place. Si vous faites fonctionner le châssis avec un slot découvert, le
système surchauffera.
PRECAUCIÓN
Si no instala un módulo o un fuente de alimentación en la ranura, deberá mantener el panel de
ranuras en su lugar. Si pone en funcionamiento el chasis con una ranura descubierta, el
sistema sufrirá sobrecalentamiento.
CAUTION
Carefully follow the mechanical guides on each side of the power supply slot and make sure the
power supply is properly inserted in the guides. Never insert the power supply upside down.
VORSICHT
Brocade 6510 Hardware Installation Guide
53-1002174-10
Beachten Sie mechanischen Führungen an jeder Seite des Netzteils, das ordnungegemäß in
die Führungen gesteckt werden muss. Das Netzteil darf niemals umgedreht eingesteckt
werden.
63
Danger Notices
MISE EN
GARDE
Suivez attentivement les repères mécaniques de chaque côté du slot du bloc d'alimentation et
assurez-vous que le bloc d'alimentation est bien inséré dans les repères. N'insérez jamais le
bloc d'alimentation à l'envers.
PRECAUCIÓN
Siga cuidadosamente las guías mecánicas de cada lado de la ranura del suministro de energía
y verifique que el suministro de energía está insertado correctamente en las guías. No inserte
nunca el suministro de energía de manera invertida.
CAUTION
The power supply switch must be in the off position when you insert the power supply into the
chassis. Damage to the switch can result if a live power supply is installed.
VORSICHT
Der Schalter des Netzteils muss in der Stellung „Aus“ stehen, wenn das Netzteil in das
Gehäuse eingesetzt wird. Wenn ein spannungsführendes Netzteil (Schalterstellung "Ein")
eingebaut wird, kann dies zu Beschädigungen am Switch führen.
MISE EN
GARDE
Le commutateur d'alimentation doit être en position d'arrêt lorsque vous insérez la source
d'alimentation dans le châssis. Si une source d'alimentation sous tension est installée, des
dommages peuvent être causés.
PRECAUCIÓN
El interruptor de la fuente de alimentación debe estar en la posición de apagado en el
momento de introducirla en el chasis. El conmutador puede resultar dañado si se instala una
fuente de alimentación activa.
Danger Notices
A danger notification calls your attention to a possible hazard that can cause injury or death. The
following are the warnings used in this manual.
"Gefahr" weist auf eine mögliche Gefährdung hin, die zu Verletzungen oder Tod führen können. Sie
finden die folgenden Warnhinweise in diesem Handbuch.
Un danger attire votre attention sur un risque possible de blessure ou de décès. Ci-dessous, vous
trouverez les avertissements utilisés dans ce manuel.
Una señal de peligro le llama la atención sobre cualquier posible peligro que pueda ocasionar daños
personales o la muerte. A continuación se dan las advertencias utilizadas en este manual.
Electrical dangers
DANGER
For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.
GEFAHR
64
Aus Sicherheitsgründen sollte ein EGB-Armband zum Schutz von elektronischen gefährdeten
Bauelementen mit einem 1 Megaohm-Reihenwiderstand ausgestattet sein.
Brocade 6510 Hardware Installation Guide
53-1002174-10
Caution and Danger Notices
DANGER
Pour des raisons de sécurité, la dragonne ESD doit contenir une résistance de série 1 méga
ohm.
PELIGRO
Por razones de seguridad, la correa de muñeca ESD deberá contener un resistor en serie de
1 mega ohmio.
DANGER
Make sure that the power source circuits are properly grounded, then use the power cord
supplied with the device to connect it to the power source.
GEFAHR
Stellen Sie sicher, dass die Stromkreise ordnungsgemäß geerdet sind. Benutzen Sie dann das
mit dem Gerät gelieferte Stromkabel, um es an die Srromquelle anzuschließen.
DANGER
Vérifiez que les circuits de sources d'alimentation sont bien mis à la terre, puis utilisez lecordon
d'alimentation fourni avec le dispositif pour le connecter à la source d'alimentation.
PELIGRO
Verifique que circuitos de la fuente de corriente están conectados a tierra correctamente; luego
use el cordón de potencia suministrado con el instrumento para conectarlo a la fuente de
corriente
DANGER
Remove both power cords before servicing.
GEFAHR
Trennen Sie beide Netzkabel, bevor Sie Wartungsarbeiten durchführen.
DANGER
Retirez les deux cordons d'alimentation avant toute maintenance.
PELIGRO
Desconecte ambos cables de alimentación antes de realizar reparaciones.
DANGER
Disconnect the power cord from all power sources to completely remove power from the device.
GEFAHR
Ziehen Sie das Stromkabel aus allen Stromquellen, um sicherzustellen, dass dem Gerät kein
Strom zugeführt wird.
DANGER
Débranchez le cordon d'alimentation de toutes les sources d'alimentation pour couper
complètement l'alimentation du dispositif.
PELIGRO
Para desconectar completamente la corriente del instrumento, desconecte el cordón de
corriente de todas las fuentes de corriente.
DANGER
To avoid high voltage shock, do not open the device while the power is on.
Brocade 6510 Hardware Installation Guide
53-1002174-10
65
Caution and Danger Notices
GEFAHR
Das eingeschaltete Gerät darf nicht geöffnet werden, da andernfalls das Risiko eines
Stromschlags mit Hochspannung besteht.
DANGER
Afin d'éviter tout choc électrique, n'ouvrez pas l'appareil lorsqu'il est sous tension.
PELIGRO
Para evitar una descarga de alto voltaje, no abra el dispositivo mientras esté encendido.
DANGER
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
GEFAHR
Es besteht Explosionsgefahr, wenn ein unzulässiger Batterietyp eingesetzt wird.
Verbrauchte Batterien sind entsprechend den geltenden Vorschriften zu entsorgen.
DANGER
Risque d'explosion en cas de remplacement de la pile par un modèle incorrect.
Débarrassez-vous des piles usagées conformément aux instructions.
PELIGRO
Riesgo de explosión si se sustituye la batería por una de tipo incorrecto.
Deshágase de las baterías usadas de acuerdo con las instrucciones.
Dangers related to equipment weight
DANGER
Make sure the rack or cabinet housing the device is adequately secured to prevent it from
becoming unstable or falling over.
66
GEFAHR
Stellen Sie sicher, dass das Gestell oder der Schrank für die Unterbringung des Geräts auf
angemessene Weise gesichert ist, so dass das Gestell oder der Schrank nicht wackeln oder
umfallen kann.
DANGER
Vérifiez que le bâti ou le support abritant le dispositif est bien fixé afin qu'il ne devienne pas
instable ou qu'il ne risque pas de tomber.
PELIGRO
Verifique que el bastidor o armario que alberga el instrumento está asegurado correctamente
para evitar que pueda hacerse inestable o que caiga.
Brocade 6510 Hardware Installation Guide
53-1002174-10