Crestron C2N-IIF-SPMK
Intercom Interface Mounting Kit
Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2004 Crestron Electronics, Inc.
Crestron C2N-IIF-SPMK
Intercom Interface Mounting Kit
Contents
Intercom Interface Mounting Kit: C2N-IIF-SPMK
1
Introduction......................................................................................1
Features and Functions ..........................................................1
Physical Description ..............................................................1
Assembly..........................................................................................4
Further Inquiries...............................................................................8
Future Updates .................................................................................8
Return and Warranty Policies ..........................................................9
Merchandise Returns / Repair Service ..................................9
CRESTRON Limited Warranty ............................................9
Installation Guide - DOC. 6265
Contents • i
Crestron C2N-IIF-SPMK
Intercom Interface Mounting Kit
Intercom Interface Mounting Kit:
C2N-IIF-SPMK
Introduction
Features and Functions
The Crestron® Intercom Interface Mounting Kit (C2N-IIF-SPMK) is used
to install a C2N-IIF Intercom Interface into select door station products
from Holovision®. The kit includes a speaker, microphone, and mounting
hardware for attaching the C2N-IIF to door station plates from
Holovision (sold separately).
Functional Summary
• Complete kit includes mounting plate, speaker and microphone
assemblies, and mounting hardware
• Compatible with a variety of Holovision door station plates
Physical Description
The C2N-IIF-SPMK can be used with Holovision’s gate entry boxes and
door station plates as shown in the following diagrams.
C2N-IIF Mounted on Gate Entry Plate(L) and on Door Station Plate (R)
Installation Guide - DOC. 6265
Intercom Interface Mounting Kit: C2N-IIF-SPMK • 1
Intercom Interface Mounting Kit
Crestron C2N-IIF-SPMK
Dimensions for the C2N-IIF-SPMK are shown in the following diagram.
C2N-IIF-SPMK Physical Views
2 • Intercom Interface Mounting Kit: C2N-IIF-SPMK
Installation Guide - DOC. 6265
Crestron C2N-IIF-SPMK
Intercom Interface Mounting Kit
The C2N-IIF-SPMK includes all of the parts required for mounting a
C2N-IIF to a Holovision door station plate. The following table lists all
of the parts included with the C2N-IIF-SPMK.
Supplied Components
DESCRIPTION
PART
NUMBER
QUANTITY
Mounting Plate
2010173
1
Screw, 08-32, 1/4” L, pan phillips
2007264
2
Screw, 06-32, 1 3/4” L, flat phillips
2010428
4
Spacer, 06, 1 7/16” L, round, 1/4” OD
2010427
4
Speaker Assembly
4005371
1
Microphone Assembly
4005461
1
Screw, 04-40, 3/4” L, pan phillips
2007184
2
Spacer, 04, 3/8” L, round, 1/4” OD
2007088
2
Washer, flat
2007658
2
The C2N-IIF-SPMK is compatible with the following Holovision door
station models:
• Basic Model 100
• Camera Models 200 and 201
• Keyless Model 101
• Gate Entry Models: 300, 301, 302, and 303
NOTE: When ordering a Holovision plate, specify that the plate is to be
used with a Crestron C2N-IIF. Older Holovision plates may not have the
appropriate mounting provisions for the C2N-IIF-SPMK.
NOTE: If the C2N-IIF-SPMK is being used with a camera-capable door
station plate, the camera is not included with the C2N-II-SPMK.
NOTE: The C2N-IIF-SPMK cannot be used with Holovision plates that
use a camera hidden behind the speaker grate.
Installation Guide - DOC. 6265
Intercom Interface Mounting Kit: C2N-IIF-SPMK • 3
Intercom Interface Mounting Kit
Crestron C2N-IIF-SPMK
Assembly
Tools Required
• #2 Phillips tip screwdriver
• Tin Snips (for installation with a rough-in box)
Complete the following procedure in the order provided.
NOTE: When installing the C2N-IIF-SPMK with Holovision’s keypadequipped plates, refer to Diagram A. For all other compatible Holovision
plates, refer to Diagram B.
NOTE: Observe the orientation of all components in the assembly
diagrams to ensure proper fit.
1. Using the supplied 3/4” screws, washers, and 3/8” spacers,
mount the microphone to the indicated location on the door
station plate as shown in the following diagram. Tighten the
screws ¾ turn after making contact with the washers. Do not
overtighten.
Securing the Microphone
4 • Intercom Interface Mounting Kit: C2N-IIF-SPMK
Installation Guide - DOC. 6265
Crestron C2N-IIF-SPMK
Intercom Interface Mounting Kit
2. As shown in the following diagram, position the speaker over
the mounting holes in the door station plate.
Positioning the Speaker
3. Position the supplied 1 7/16” spacers over the speaker mounting
holes as shown in the following diagram. Using the supplied
1 3/4” screws, secure the door station plate, speaker, and
spacers to the appropriate holes on the mounting plate.
NOTE: Use a toothpick or small dowel to line up the parts during
assembly.
Securing the Mounting Plate
Installation Guide - DOC. 6265
Intercom Interface Mounting Kit: C2N-IIF-SPMK • 5
Intercom Interface Mounting Kit
Crestron C2N-IIF-SPMK
NOTE: The nuts that are built in to the mounting plate should face the
door station plate.
NOTE: Diagram A and Diagram B use different holes on the mounting
plate to mount to the door station plate.
4. Using the supplied 1/4” screws, secure the C2N-IIF to the
mounting plate as shown in the following diagram.
Attaching the C2N-IIF to the Mounting Plate
NOTE: The C2N-IIF must be placed on the mounting plate with the
orientation shown in the diagrams.
6 • Intercom Interface Mounting Kit: C2N-IIF-SPMK
Installation Guide - DOC. 6265
Crestron C2N-IIF-SPMK
Intercom Interface Mounting Kit
5. Connect all wires to the C2N-IIF as described in the C2N-IIF
Operation & Installation Guide (Doc. 6235) which can be
downloaded from Downloads | Product Manuals section of the
Crestron website (www.crestron.com).
NOTE: The red wire from the microphone is connected to the “MIC”
terminal on the C2N-IIF. The black wire and shield wire are connected to
the “GND” terminal located next to the “MIC” terminal.
6. Install the assembly per the instructions provided with the
Holovision door plate.
To install into a Holovision rough-in box, tilt the assembly so
the bottom can be placed in the box first and then shift the top
of the assembly to the right, so the rest of the assembly can be
placed in the box.
Installation Guide - DOC. 6265
Intercom Interface Mounting Kit: C2N-IIF-SPMK • 7
Intercom Interface Mounting Kit
Crestron C2N-IIF-SPMK
Further Inquiries
If you cannot locate specific information or have questions after
reviewing this guide, please take advantage of Crestron's award winning
customer service team by calling the Crestron corporate headquarters at
1-888-CRESTRON [1-888-273-7876]. For assistance in your local time
zone, refer to the Crestron website (www.crestron.com) for a listing of
Crestron worldwide offices.
You can also log onto the online help section of the Crestron website to
ask questions about Crestron products. First-time users will need to
establish a user account to fully benefit from all available features.
Future Updates
As Crestron adds improvements to the C2N-IIF-SPMK, additional
information may be made available as manual updates. These updates are
solely electronic and serve as intermediary supplements prior to the
release of a complete technical documentation revision.
Check the Crestron website (www.crestron.com) periodically for manual
update availability and its relevance. Updates are available from the
Download | Product Manuals section and are identified as an
“Addendum” in the Download column.
8 • Intercom Interface Mounting Kit: C2N-IIF-SPMK
Installation Guide - DOC. 6265
Crestron C2N-IIF-SPMK
Intercom Interface Mounting Kit
Return and Warranty Policies
Merchandise Returns / Repair Service
1.
No merchandise may be returned for credit, exchange, or service without prior
authorization from CRESTRON. To obtain warranty service for CRESTRON
products, contact the factory and request an RMA (Return Merchandise
Authorization) number. Enclose a note specifying the nature of the problem, name
and phone number of contact person, RMA number, and return address.
2.
Products may be returned for credit, exchange, or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped
freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J., or its authorized
subsidiaries, with RMA number clearly marked on the outside of all cartons.
Shipments arriving freight collect or without an RMA number shall be subject to
refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a
15% restocking fee, plus shipping costs, on any products returned with an RMA.
3.
Return freight charges following repair of items under warranty shall be paid by
CRESTRON, shipping by standard ground carrier. In the event repairs are found to
be non-warranty, return freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in
materials and workmanship under normal use for a period of three (3) years from the date of
purchase from CRESTRON, with the following exceptions: disk drives and any other moving or
rotating mechanical parts, pan/tilt heads and power supplies are covered for a period of one (1)
year; touchscreen display and overlay components are covered for 90 days; batteries and
incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized
CRESTRON dealer. Purchasers should inquire of the dealer regarding the nature and extent of the
dealer's warranty, if any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in
any application other than that for which it was intended, or if it has been subjected to misuse,
accidental damage, modification, or improper installation procedures. Furthermore, this warranty
does not cover any product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic
damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for
any claim made by a third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for
parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be
covered only by the unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed
or implied, nor authorizes any other party to offer any warranty, including any implied warranties
of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed
by law are limited to the terms of this limited warranty. This warranty statement supercedes all
previous warranties.
Trademark Information
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered
trademark of Microsoft Corporation. Windows95/98/Me and WindowsNT/2000 are trademarks of Microsoft Corporation.
Installation Guide - DOC. 6265
Intercom Interface Mounting Kit: C2N-IIF-SPMK • 9
Intercom Interface Mounting Kit
Crestron C2N-IIF-SPMK
This page intentionally left blank.
10 • Intercom Interface Mounting Kit: C2N-IIF-SPMK
Installation Guide - DOC. 6265
Crestron C2N-IIF-SPMK
Intercom Interface Mounting Kit
This page intentionally left blank.
Installation Guide - DOC. 6265
Intercom Interface Mounting Kit: C2N-IIF-SPMK • 11
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Installation Guide - DOC. 6265
05.04
Specifications subject to
change without notice.