KD7A
Socket 462 System Board
User’s Manual
4200-0385-02
Rev. 1.00
Copyright and Warranty Notice
The information in this document is subject to change without notice and does not
represent a commitment on part of the vendor, who assumes no liability or
responsibility for any errors that may appear in this manual.
No warranty or representation, either expressed or implied, is made with respect to the
quality, accuracy or fitness for any particular part of this document. In no event shall
the manufacturer be liable for direct, indirect, special, incidental or consequential
damages arising from any defect or error in this manual or product.
Product names appearing in this manual are for identification purpose only and
trademarks and product names or brand names appearing in this document are the
property of their respective owners.
This document contains materials protected under International Copyright Laws. All
rights reserved. No part of this manual may be reproduced, transmitted or transcribed
without the expressed written permission of the manufacturer and authors of this
manual.
If you do not properly set the motherboard settings, causing the motherboard to
malfunction or fail, we cannot guarantee any responsibility.
KD7A
Table Of Contents
KD7A 快速安裝指引 ................................................................................ 2
KD7A のクイックインストールガイド ................................................ 4
KD7A Schnellinstallationsanleitung ....................................................... 6
KD7A Guide d’Installation Rapide ........................................................ 8
Краткое руководство по установке KD7A ....................................... 10
Guida all’installazione veloce Scheda madre KD7A........................... 12
Chapter 1.
1-1.
1-2.
Chapter 2.
2-1.
2-2.
2-3.
2-4.
Hardware Setup.................................................................... 2-1
Install The Motherboard...........................................................................2-1
Install CPU and Heatsink.........................................................................2-1
Install System Memory ............................................................................2-3
Connectors, Headers and Switches ..........................................................2-4
(1). ATX Power Input Connectors........................................................2-4
(2). FAN Connectors.............................................................................2-5
(3). CMOS Memory Clearing Header ..................................................2-6
(4). S2K Mode Select Header...............................................................2-6
(5). Wake-up Header.............................................................................2-7
(6). Front Panel Switches & Indicators Headers ..................................2-8
(7). Additional USB Port Headers........................................................2-9
(8). Front Panel Audio Connection Header ........................................2-10
(9). Internal Audio Connectors ...........................................................2-11
(10). Accelerated Graphics Port Slot ....................................................2-11
(11). Floppy Disk Drive Connector ......................................................2-12
(12). IDE Connectors............................................................................2-13
(13). Back Panel Connectors ................................................................2-14
Chapter 3.
3-1.
3-2.
3-3.
Introduction .......................................................................... 1-1
Features & Specifications ........................................................................1-1
Layout Diagram .......................................................................................1-2
BIOS Setup............................................................................ 3-1
SoftMenu Setup........................................................................................3-2
Standard CMOS Features.........................................................................3-4
Advanced BIOS Features.........................................................................3-7
User’s Manual
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
3-10.
3-11.
3-12.
3-13.
Advanced Chipset Features....................................................................3-10
Integrated Peripherals ............................................................................3-15
Power Management Setup .....................................................................3-19
PnP/PCI Configurations.........................................................................3-23
PC Health Status ....................................................................................3-25
Load Fail-Safe Defaults .........................................................................3-26
Load Optimized Defaults .......................................................................3-26
Set Password ..........................................................................................3-26
Save & Exit Setup ..................................................................................3-26
Exit Without Saving...............................................................................3-26
Appendix A.
Install VIA 4-in-1 Driver ................................................................. A-1
Appendix B.
Install Audio Driver ......................................................................... B-1
Appendix C.
Install LAN Driver ........................................................................... C-1
Appendix D.
Install VIA USB 2.0 Driver .............................................................D-1
Appendix E.
BIOS Update Guide ......................................................................... E-1
Appendix F.
Hardware Monitoring (The Winbond Hardware Doctor Utility) .. F-1
Appendix G.
Troubleshooting (Need Assistance?)...............................................G-1
Appendix H.
How to Get Technical Support ........................................................H-1
KD7A
1
User’s Manual
KD7A 快速安裝指引
2
KD7A 快速安裝指引
如您要瞭解此主機板更詳細的資訊,請參閱我們的完整版使用手冊,裡面會有詳盡的說明。此快速
安裝手冊是給有經驗的系統組裝者使用,如果這是您第一次嘗試來組裝您的電腦系統,我們建議您
先去閱讀完整版的使用手冊,或是詢問技術人員來幫助您組裝您的電腦系統。(完整版的使用手冊
已包覆在隨本主機板所附的驅動程式與應用光碟之中。)
處理器的安裝
本主機板提供零出力(Zero Insertion Force, ZIF)
式 Socket 462,以方便安裝 AMD Socket A。您所
購買的 CPU 應已配備一組散熱套件及散熱片,如
果沒有,請另行購買專為 Socket A 設計的散熱套
件及散熱片。
請參考這裡所表示的圖來安裝 CPU 中央處理器和
散熱器。(僅供參考。您的散熱器與風扇組合可
能不見得與這一個完全相同。)
1.
請找出這塊主機板的 Socket 462 位置。將 CPU
插座桿拉出至插座旁,然後將插座桿以 90 度
角向上拉。
2.
將 CPU 的缺角對準 CPU 插座的缺角,CPU
插腳的一端向下置 CPU 插座。因為只能朝著
一個固定的方向插入 CPU,如果遇到阻礙
時,切勿勉強用力。最後壓住 CPU,拴上插
座桿。
3.
請將散熱器底面的自黏膠模移除,散熱器底
部凹角一端面向 CPU 插座標示 “Socket 462”
的一方,散熱器面向下蓋住 CPU,直到完全
蓋住 CPU 為止。
4.
先將固定夾具短的一邊壓下扣住 CPU 插座底
端的中間鎖扣。
5.
再以螺絲起子插入固定夾具長的一邊的凹
槽,壓下扣住 CPU 插座底端的中間鎖扣。現
在散熱器與風扇組合已互相緊扣在 CPU 插座
上。
6.
將散熱器與風扇組合的風扇電源端子與主機
板上面的風扇電源端子連接。
注意:請不要忘記去設定處理器正確的匯流排頻
率和倍頻的數值。
KD7A
KD7A 快速安裝指引
3
將主機板安裝到機殼上
當您將處理器安裝到主機板上之後,您便可以開始將主機板固定到電腦機殼裡去。首先;請您先將
主機板固定到電腦機殼。大多數的電腦機殼底座都有許多的固定孔位,請將主機板上的固定孔位與
機殼底座上的固定孔位對準。如果孔能對準並且有螺絲孔,就表示可使用銅柱來固定主機板。另外;
您可以使用塑膠墊片來讓螺絲與主機板的 PCB 表層隔離(絕緣)。
安裝記憶體模組
1.
找出您主機板上 DIMM 插槽的位置。
2.
請您小心地抓住 DIMM 模組的兩側,請勿碰觸
其接點。
3.
請將記憶體模組上的榫子與 DIMM 插槽上的卡
榫對準。
4.
穩固地施壓來將記憶體模組向下插入 DIMM 插
槽,直到 DIMM 插槽兩側的模組固定夾自動地
扣入記憶體模組的固定夾缺口為止。切勿太過施力地來將 DIMM 模組插入插槽,因為您只能
以一個固定的方向來插入 DIMM 模組。
5.
要取出 DIMM 模組,請您向外側同時地壓下 DIMM 插槽兩側的模組固定夾,即可將 DIMM 模
組抽取出來。
注意:靜電會造成電腦或是附加卡上電子元件的損壞,在您要進行這些程序之前,請確認您已經藉
由暫時地接觸已接地的金屬物體來放掉您身上所帶有的靜電。
連接器、連接頭以及附加卡的安裝
在任何一部電腦機殼的裡面,都必需連接一些纜線與插頭。這些纜線與插頭通常都是一對一的連接
至主機板的連接埠上,您必需注意任何一條纜線的連接方向。如果可能的話,請一併注意連接埠第
一根針腳的位置。您將會安裝一些特殊功能的附加卡到主機板上面,像是 SCSI 卡或是 AGP 顯示
卡等等。當您將它們安裝到主機板上適當的插槽之後,請以螺絲將這些附加卡與機殼背板牢牢地固
定好,避免有鬆動的情況發生。
如您想要瞭解相關且更為詳細的資訊,請參閱我們的完整版使用手冊,裡面會有詳盡的說明。
將電源供應器的電源線連接頭與主機板上的 ATX12V 電源接頭連接起來
請將電源供應器的 ATX 電源接頭確實地壓入主機板上的 ATX12V 電源接頭,並確定連接妥當。
BIOS 的設定
當您將所有的硬體安裝完畢以後,就可以開啟電腦的電源並進入 BIOS 的選項。如您想要瞭解相關
且更為詳細的資訊,請參閱我們的完整版使用手冊,裡面會有詳盡的說明。
User’s Manual
4
KD7A のクイックインストールガイド
KD7A のクイックインストールガイド
このマザーボードの詳細については、ユーザーズマニュアルの完全版を参照してください。この
クイックインストールガイドは、経験あるシステム構築者向けに書かれました。今回始めてコン
ピュータシステムをセットアップする方は、まず完全版のマニュアルをお読みになるか、専門技
術者に連絡してコンピュータシステムのセットアップを行うようお勧めします。(完全なユーザ
ーズマニュアルはこのマザーボードに付属するドライバとユーティリティ CD を検索して入手
できます。)
プロセッサの取り付け
このマザーボードは ZIF(ゼロインサーションフォー
ス)Socket 462 を提供して AMD Socket A CPU をイン
ストールします。お買い上げになった CPU には、ヒ
ートシンクと冷却ファンのキットが付属しています。
付属していない場合、Socket A 向けに特別に設計され
たキットをお求めください。
ここに示した図を参照して、CPU とヒートシンクを
取り付けます(この図は参照専用です。お使いのヒー
トシンクとファンアセンブリはこの図と異なってい
ることがあります)。
1. このマザーボードの Socket 462 を探します。CPU
のリリースレバーを横に引っ張って掛け金を外
し、上まで引き上げます。
2. CPU のノッチを CPU のソケットのノッチに合わ
せます。そのピンの横側を下にして CPU のソケ
ットに差し込みます。CPU に差し込むときに無理
な力を入れないでください。ピンは一方向にだけ
フィットするようになっています。CPU のリリー
スレバーを閉じます。
3. ヒートシンクのプラスチックフィルム接着剤を
はがします。ヒートシンクの段のある部分 が
“Socket 462”の文字のある側を向いていることを
確認してください。ヒートシンクの面を下にして、
プロセッサを完全に覆うまで降ろします。
4. まず支持クリップの短い方の端を押し下げて、ソ
ケット下部のセンターラグに固定します。
5. ネジ回しを使用して、支持クリップの長い方の端
のスロットに差し込みます。クリップを押し下げ
て、ソケット上部のセンターラグに固定します。
これで、ヒートシンクとファンアセンブリが CPU
のソケットにしっかり取り付けられました。
6. ヒートシンクとファンアセンブリのファンコネ
クタを、マザーボードのファンコネクタに取り付
けます。
KD7A
KD7A のクイックインストールガイド
5
注意:正しいバス周波数と倍数をプロセッサ用に設定するのを忘れないでください。
マザーボードをシャーシに取り付ける
マザーボードにプロセッサを取り付けた後、シャーシにマザーボードを固定することができるよ
うになります。まず、シャーシにマザーボードを固定する必要があります。ほとんどのコンピュ
ータシャーシには、多くの取り付け穴の付いた台が付属しており、それを使用することでマザー
ボードをしっかり取り付けたり、同時にショートを避けることができます。シャーシに付属する
飾りボタンかスペーサーを使用してマザーボードを固定します。
RAM モジュールの取り付け
1.
ボードの DIMM スロットを探します。
2.
DIMM モジュールの 2 つのエッジがそのコネクタ
に触れないように、注意して持ちます。
3.
モジュールのノッチキーをスロットのリブに合
わせます。
4.
モジュールをスロットにしっかり押し込むと、ス
ロットの両側にあるイジェクタタブが取り付け
ノッチにかちっと音を立てて自動的にはめ込ま
れます。DIMM モジュールに余分な力をかけないでください。DIMM モジュールは一方向に
しかフィットしません。
5.
DIMM モジュールは、
スロットの 2 つのイジェクタタブを外側に同時に引っ張ると外れます。
注意:静電気はコンピュータやオプションのボードの電気コンポーネントを損傷させることがあ
ります。これらの手順を開始する前に、アースされた金属物体に軽く触れて静電気を必ず放電し
てください。
コネクタ、ヘッダ、スイッチおよびアダプタ
コンピュータのケース内部には、複数のケーブルやプラグを接続できます。これらのケーブルや
プラグは、通常マザーボードにあるコネクタに 1 つずつ接続されます。ケーブルの接続方向には
十分な注意を払い、また必要に応じ、コネクタの第 1 ピンの位置にも注目する必要があります。
SCSI アダプタ、AGP アダプタのような特殊なニーズ向けには、それに対応したアダプタを取り
付けてください。アダプタをマザーボードのスロットに取り付けたら、ネジでシャーシの背面パ
ネルに固定してください。
詳細については、ユーザーズマニュアルの完全版を参照してください。
電源コネクタを ATX12V 電源コネクタに差し込む
電源装置から出ている電源ブロックコネクタをこの ATX12V 電源に接続します。コネクタが十
分奥まで装着されていることをご確認ください。
BIOS のセットアップ
ハードウェアの取り付けが完了したら、コンピュータの電源をオンにし、BIOS Setup アイテム
に移動して、プロセッサのパラメータをセットアップします。詳細については、ユーザーズマニ
ュアルの完全版を参照してください。
User’s Manual
6
KD7A Schnellinstallationsanleitung
KD7A Schnellinstallationsanleitung
Beziehen Sie sich bitte für detaillierte Informationen über diese Hauptplatine auf die vollständige Version
des Benutzerbuchs. Diese Schnellinstallationsanleitung ist für erfahrene Systemaufbauer gedacht. Ist es
Ihr erster Versuch ein Computersystem aufzubauen, dann empfehlen wir Ihnen zuerst das vollständige
Benutzerhandbuch zu lesen oder einen Techniker zum Aufbauen des Systems zu Hilfe zu holen. (Ein
komplettes Handbuch finden Sie auf der CD mit den Treibern und Hilfsprogrammen, die diesem
Motherboard beiliegt.)
Installieren des Prozessors
Dieses Motherboard verfügt über einen ZIF (Zero
Insertion Force) Sockel 462 zur Installation eines AMD
Socket A CPU. Ihre CPU sollte über ein Kühlblech und
einen Lüfter verfügen. Wenn dies nicht der Fall ist, kaufen
Sie bitte diese Teile speziell für den Sockel A.
Bitte schauen Sie sich zur Installation von CPU und
Kühlblech diese Abbildung an. (Nur zur Referenz - Ihr
Kühlblech & Lüftergefüge könnten sich von dieser
Abbildung unterscheiden.)
1.
Finden Sie Sockel 462 auf diesem Motherboard.
Ziehen Sie den CPU-Haltehebel zur Seite, um ihn zu
entriegeln und ziehen ihn dann ganz hoch.
2.
Richten Sie die CPU-Kerbe mit der Sockelkerbe der
CPU aus. Stecken Sie den Prozessor mit den Pins
nach unten in den CPU-Sockel. Wenden Sie keine
Gewalt beim Einsetzend der CPU an; sie paßt nur in
eine Richtung hinein. Schließen Sie den
CPU-Haltehebel.
3.
Entfernen Sie den Plastikfilm vom Kühlblech. Stellen
Sie sicher, daß der abgestufte Teil des Kühlblechs in
Richtung des Sockelendes zeigt, auf dem “Socket
462” steht. Setzen Sie das Kühlblech mit dem Gesicht
nach unten auf den Prozessor, bis es den Prozessor
komplett abdeckt.
4.
Drücken Sie das kurze Ende des Halteclips zuerst an,
um es mit der Mittellasche unten am Sockel zu
verriegeln.
5.
Setzen Sie es mit einem Schraubenzieher in den
Schlitz am langen Ende des Halteclips. Drücken Sie
den Clip nach unten, um ihn mit der Mittellasche oben
am Sockel zu verriegeln. Nun sind Kühlblech &
Lüftergefüge fest mit dem CPU-Sockel verbunden.
6.
Verbinden Sie den Lüfteranschluß von Kühlblech &
Lüftergefüge
mit
dem
Lüfteranschluß
am
Motherboard.
KD7A
KD7A Schnellinstallationsanleitung
7
Achtung: Vergessen Sie nicht, die korrekte Busfrequenz und -Multiplikator für Ihren Prozessor
einzustellen.
Installieren der Hauptplatine im Gehäuse
Nach der Installation des Prozessors können Sie anfangen die Hauptplatine im Computergehäuse zu
befestigen. Die meisten Gehäuse haben eine Bodenplatte, auf der sich eine Reihe von Befestigungslöcher
befinden, mit deren Hilfe Sie die Hauptplatine sicher verankern können und zugleich Kurzschlüsse
verhindern. Verwenden Sie entweder die Dübeln oder die Abstandhalter, um die Hauptplatine auf der
Bodenplatte des Gehäuses zu befestigen.
Installation der RAM-Module
1.
Finden Sie den DIMM-Steckplatz auf dem Board.
2.
Halten Sie ie beiden Ränder des DIMM-Moduls
vorsichtig fest, wobei Sie darauf achten, nicht die
Anschlüsse zu berühren.
3.
Richten Sie die Nut am Modul mit der Erhöhung am
Steckplatz aus.
4.
Drücken Sie das Modul fest in die Steckplätze, bis die
Auswurflaschen zu beiden Seiten des Steckplatzes
automatisch in die Befestigungskerbe einschnappen. Wenden Sie keine Gewalt beim Einsetzen des
DIMM-Moduls an; es paßt nur in eine Richtung hinein.
5.
Zum Ausbau der Module drücken Sie die beiden Auswurflaschen auf dem Steckplatz nach außen
zusammen und ziehen das Modul heraus.
Anschlüsse, Sockel, Schalter und Adapter
Im Inneren des Gehäuses findet man in jedem Computer viele Kabel und Stecker, die angeschlossen
werden müssen. Diese Kabel und Stecker werden normalerweise einzeln mit den Anschlüssen auf der
Hauptplatine verbunden. Sie müssen genau auf die Anschlussorientierung der Kabel achten und, wenn
vorhanden, sich die Position des ersten Pols des Anschlusses merken. Wenn Sie Adapter wie z.B.
SCSI-Adapter, AGP-Adapter usw. installieren, befestigen Sie bitte die Adapter immer mit Hilfe der
Schrauben auf die Rückseite des Computergehäuses.
Für detaillierte Informationen beziehen Sie sich bitte auf das vollständige Benutzerhandbuch.
Verbinden der Netzstecker mit dem ATX12V-Anschluss
Denken Sie daran, den Anschluss des ATX-Netzteils fest in das Ende mit dem ATX12V-Anschluss zu
drücken, um eine feste Verbindung zu garantieren.
BIOS-Setup
Schalten Sie nach der vervollständigten Hardwareinstallation den Computer ein und gehen zur Option im
BIOS, um die Prozessorparameter einzustellen. Für detaillierte Informationen beziehen Sie sich bitte auf
das vollständige Benutzerhandbuch.
User’s Manual
8
KD7A Guide d’Installation Rapide
KD7A Guide d’Installation Rapide
Pour des informations relatives à cette carte mère plus détaillées, veuillez vous référer à notre version
complète du manuel utilisateur. Ce guide d’installation rapide est créé pour les assembleurs système
expérimentés. S’il s’agit de votre premier essai pour installer un ordinateur, nous vous suggérons de lire
d’abord le manuel en version complète ou de demander l’aide d’un technicien pour vous aider à
configurer le système ordinateur. (Un manuel de l'utilisateur complet est disponible en naviguant dans le
CD des pilotes et utilitaires fournis avec la carte mère.)
Installer le Processeur
Cette carte mère fournit un support ZIF (Zero Insertion
Force)
Socket
462
permettant
d'installer
le
Microprocesseur AMD Socket A. Le microprocesseur que
vous achetez doit être muni d'un système de
refroidissement avec dissipateur thermique et ventilateur.
Dans le cas contraire, veuillez en acheter un, conçu
spécialement pour les microprocesseurs Socket A.
Veuillez vous référer à la figure illustrée ci-contre pour
installer le processeur et le dissipateur thermique.
(Démonstration donnée à titre indicatif uniquement.
L’assemblage de votre dissipateur thermique et de votre
ventilateur peut ne pas être tout à fait identique à celui-ci.)
1.
Repérez le support Socket 462 situé sur cette carte
mère. Tirez le levier de maintien du processeur vers
l'extérieur pour le libérer puis soulevez-le
complètement vers le haut.
2.
Alignez l’encoche du processeur avec celle du support
pour processeur. Installez le processeur avec sa broche
faisant face au support pour processeur. Ne forcez pas
en insérant le processeur; il ne peut s’insérer que dans
une seule direction. Rabattez le levier de maintien du
processeur.
3.
Retirez le film adhésif du dissipateur thermique.
Assurez-vous que la partie surélevée du dissipateur
thermique fait face à l’extrémité du support marquée
“Socket 462”. Installez le dissipateur thermique pour
qu'il fasse face au processeur et jusqu’à ce qu’il
couvre complètement le processeur.
4.
Tout d'abord, poussez vers le bas l'extrémité courte de
la bride de fixation pour verrouiller sur le crochet
central situé en bas du support.
5.
Utilisez un tournevis pour insérer dans la fente la
longue extrémité de la bride de fixation. Poussez la
bride de fixation vers l'avant pour verrouiller sur le
crochet central situé en haut du support. L'assemblage
du dissipateur Thermique et du ventilateur est
maintenant solidement fixé sur le support du CPU.
6.
Fixez le connecteur du ventilateur du dissipateur thermique & du ventilateur sur le connecteur
correspondant de la carte mère.
KD7A
KD7A Guide d’Installation Rapide
9
Attention: N’oubliez pas de programmer la fréquence de bus correcte et le multiple pour votre
processeur.
Installer la Carte Mre dans le Châssis
Une fois que vous aurez installé le processeur sur la carte mère, vous pourrez commencer à fixer la carte
mère sur le châssis. Tout d’abord, vous avez besoin de fixer la carte mère sur le châssis. La plupart des
châssis d’ordinateur possèdent une base sur laquelle il y a nombreux trous de montage permettant à la
carte mère d’être fixée fermement, et en même temps d’éviter les court-circuits. Utilisez les talons ou les
entretoises fixés sur le châssis pour fixer la carte mère.
Installer des Modules RAM
1.
Localisez le socle DIMM sur la carte.
2.
Maintenez les deux bords du module DIMM avec
précaution, en évitant de toucher ses connecteurs.
3.
Alignez la touche du cran avec la ligne sur le socle.
4.
Pressez fermement le module dans les socles jusqu’à
ce que les languettes d’éjection sur les deux côtés du
socle aillent automatiquement dans le cran de
montage. Ne forcez pas à l’excès sur le module
DIMM car celui-ci ne peut aller que selon une seule
orientation.
5.
Pour enlever des modules DIMM, pressez simultanément les deux languettes d’éjection sur le socle,
puis sortez le module DIMM.
Attention: L’électricité statique risque d’endommager les composants électroniques de l’ordinateur ou
des cartes optionnelles. Avant de commencer ces procédures, assurez-vous de bien décharger toute
l’électricité statique en touchant rapidement un objet métallique relié au sol.
Connecteurs, Socles de connexion, Interrupteurs et Adaptateurs
A l’intérieur du boîtier de n’importe quel ordinateur il y a plusieurs câbles et prises qui doivent être
connectés. Ces câbles et prises sont habituellement connectés les uns après les autres aux connecteurs
situés sur la carte mère. Vous avez besoin de faire attention au sens de connexion des câbles et, s’il y a
lieu, remarquez la position de la première broche du connecteur. Vous installerez certains adaptateurs
pour des besoins spéciaux, tels adaptateurs SCSI, adaptateurs AGP, etc. Lorsque vous les installez dans
les emplacements situés sur la carte mère, veuillez les fixer sur le panneau arrière du châssis à l'aide des
vis.
Pour les informations détaillées, veuillez vous référer au manuel utilisateur en version complète.
Brancher les connecteurs d'alimentation dans les connecteurs ATX12V
Souvenez-vous que vous devez pousser le connecteur de votre alimentation fermement dans le connecteur
ATX12V pour assurer une bonne connexion.
Configuration du BIOS
Une fois le matériel installé complètement, démarrez l'ordinateur et allez sur l'item dans le BIOS pour
configurer les paramètres du processeur. Pour les informations détaillées, veuillez vous référer à la
version complète du manuel utilisateur.
User’s Manual
10
Краткое руководство по установке KD7A
Краткое руководство по установке KD7A
Более подробные сведения о материнской плате приведены в руководстве пользователя. Краткое
руководство по установке предназначено для опытных специалистов. Если вы собираете
компьютер впервые, ознакомьтесь сперва с руководством пользователя или попросите техника
помочь в настройке компьютерной системы.
Установка процессора
На этой системной плате используется гнездо ZIP (с
нулевым усилием установки) типа 'Socket 462' для
процессора
AMD
Socket
A.
В
комплект
приобретаемого процессора должны входить радиатор
и вентилятор. В противном случае следует приобрести
радиатор
и вентилятор, предназначенные для
процессора AMD с разъемом 'Socket A'.
Для установки процессора и радиатора, посмотрите
пожалуйста на рисунок, показанный на этой странице.
(Только для справочной работы. Ваш радиатор и
комплект вентилятора может быть не точно такой же
как показанный рисунок здесь.)
1.
Найтите на этой плате гнездо “Socket 462”.
Вытяните рычаг гнезда процессора в сторону от
гнезда, затем поднимите его.
2.
Расположите зарубку процессора и зарубку гнезда
для процессора по одной линии. Положите
процессор со стороной контактов в гнездо
процессора.
Устанавливая
процессор,
не
прикладывайте чрезмерных усилий. Его установка
возможна только в одном положении. Опустите
рычаг гнезда процессора.
3.
Уберите ту пластическую оболочку, находящуюсь
на радиаторе. Ступенчатная часть радиатора
должна находиться лицом к стороне гнезда, где
показано слово “Socket 462”. Поместите радиатор
плоской стороной на процессор так, чтобы
процессор был полностью закрыт.
4.
Сначала, прижмите вниз короткую сторону
фиксирующего зажима до его фиксации в
центральной проушине на нижней части гнезда.
5.
Вставьте отвёрку в паз, находящийся на длинной
стороне фиксирующего зажима. Прижмите зажим
вниз до его фиксации в центральной проушине на
верхней части гнезда. Радиатор и комплект
вентилятора должны быть надежно скреплены к
гнезду процессора.
6.
Подключите разъём раздиатора и комплекта вентилятора к разъёму вентилятора на
материнской плате.
KD7A
Краткое руководство по установке KD7A
11
Внимание: Установите соответствующие частоту и кратность шины процессора.
Установка материнской платы в корпус
После установки процессора на материнскую плату можно начинать установку материнской
платы в корпус. Большая часть корпусов оборудована основанием, в котором проделаны
монтажные отверстия, которые позволяют надежно закрепить материнскую плату и предотвратить
короткие замыкания. Для крепления материнской платы к основанию используются винты и
прокладки.
Установка модулей памяти
1.
Найдите на системной плате разъем для модулей
памяти DIMM.
2.
Аккуратно, за два конца, возьмите модуль памяти,
не касаясь контактов.
3.
Совместите выемку в модуле памяти с выступом в
разъеме.
4.
Нажмите на модуль так, чтобы лепестки
выталкивателя
с
обеих
сторон
разъема
автоматически защелкнулись и вошли в пазы. Не применяйте при установке излишнюю силу.
Модуль входит в разъем только в одном положении.
5.
Для извлечения модулей памяти DIMM одновременно нажмите на лепестки выталкивателя и
вытащите модуль.
Внимание: Статическое электричество может стать причиной выхода из строя электронных
компонентов компьютера. Перед началом данной процедуры снимите с себя статический заряд,
коснувшись заземленного металлического предмета.
Разъемы, переключатели и адаптеры
Внутри корпуса компьютера необходимо расположены несколько кабелей и вилок, которые
необходимо подключить. Обычно эти кабели подключаются к разъемам, расположенным на
материнской плате. При подключении любого кабеля необходимо обращать внимание на
расположение первого контакта разъема. Для особых целей могут потребоваться специальные
адаптеры, например, адаптер SCSI, адаптер AGP и т.п.. При установке адаптеров в гнезда
материнской платы закрепите их на задней панели с помощью винтов.
За более подробной информацией обращайтесь к полному руководству пользователя.
Подключение кабелей питания к разъемам ATX12V
Обратите внимание, разъем блока питания ATX необходимо вставить в разъем ATX12V до упора,
чтобы обеспечить надежное соединение.
Настройка BIOS
По окончании установки аппаратуры включите питание и перейдите в меню BIOS Setup, чтобы
настроить параметры процессора. За более подробной информацией обращайтесь к руководству
пользователя.
User’s Manual
12
Guida all’installazione veloce Scheda madre KD7A
Guida all’installazione veloce Scheda madre KD7A
Per maggiori e dettagliate informazioni su questa scheda madre si prega di fare riferimento alla versione
integrale del Manuale utente. Questa guida all’installazione veloce è intesa per costruttori esperi di
sistemi. Se questa è la prima volta che si cerca di installare un sistema, si consiglia di leggere, innanzi
tutto, la versione integrale del manuale oppure di chiedere aiuto ad un tecnico per l’installazione.
Installazione del processore
Questa scheda madre fornisce una presa “Socket 462” ZIF
(Zero Insertion Force – forza d’inserimento zero) per
installare il processore AMD Socket A. Il processore
acquistato dovrebbe essere fornito di dispersore di calore e
ventolina per il raffreddamento. In caso contrario
acquistare un dispersore di calore specifico per la presa
Socket A.
Per il montaggio della CPU e del termodispersore,
consultare la figura accanto. Si noti che il gruppo
termodispersore-ventola illustrati possono non essere
identici a quelli effettivamente da montare.
1.
Individuare il socket 462 sulla scheda madre. Tirare
lateralmente la leva di sblocco della CPU e sollevare
la CPU completamente.
2.
Allineare la tacca della CPU con quella del socket
CPU. Appoggiare il processore con il lato di
connessione verso il basso nel socket, senza forzare.
La CPU può essere montata in una sola direzione.
Chiudere la leva di sblocco della CPU.
3.
Staccare la pellicola adesiva dal termodispersore.
the plastic film adhesive on the heatsink. Accertarsi
che la superficie del termodispersore provvista di
gradino sia rivolta verso l'estremità del socket indicato
come "Socket 462". Applicare il termodispersore con
il lato inferiore verso il basso sul processore fino a
coprirlo completamente.
4.
Tirare verso il basso il lato corto del clip di ritegno
fino ad impegno con la linguetta centrale sul lato
inferiore del socket.
5.
Con l’aiuto di un cacciavite, inserire la linguetta nella
fessura sul lato lungo del clip di ritegno. Spingere il
clip verso il basso fino ad impegno con la linguetta
centrale della parte superiore del socket. A questo
punto, il gruppo termodispersore-ventola è saldamente
fissato al socket CPU.
6.
Fissare il connettore ventola del gruppo
termodispersore-ventola al connettore ventola della scheda madre .
Attenzione: Non dimenticare di impostare la corretta frequenza multipla e BUS per il processore.
KD7A
Guida all’installazione veloce Scheda madre KD7A
13
Installazione della scheda madre sul telaio
Dopo avere installato il processore sulla scheda madre si può iniziare a fissare la scheda madre sul telaio.
Innanzi tutto è necessario fissare la scheda madre al telaio. La maggior parte dei telai ha una base sulla
quale sono presenti diversi fori di montaggio che permettono di fissare in modo accurato la scheda madre
e, allo stesso tempo, di prevenire corto circuiti. Impiegare le borchie o gli spaziatori attaccati al telaio per
fissare la scheda madre.
Installare i moduli RAM
1.
Ubicare gli alloggiamenti DIMM sulla scheda.
2.
Tenere con delicatezza i lati del modulo DIMM senza
toccare i connettori.
3.
Allineare la tacca sul modulo con la nervatura
dell’alloggiamento.
4.
Premere con fermezza il modulo nell’alloggiamento
finché le linguette d’espulsione su entrambi i lati
dell’alloggiamento scattano sulla tacca di montaggio.
Non forzare eccessivamente il modulo DIMM perché quest’ultimo si adatta solamente in una
direzione.
5.
Per rimuovere i moduli DIMM spingere contemporaneamente le due linguette d’espulsione
sull’alloggiamento, poi estrarre il modulo DIMM.
Attenzione: L’elettricità statica può danneggiare i componenti elettronici del computer o delle schede.
Prima di iniziare queste procedure, assicurarsi di avere scaricato completamente l’elettricità statica
toccando brevemente un oggetto metallico con massa a terra.
Connettori, collettori, interruttori ed adattatori
All’interno della copertura di ogni computer ci sono diversi cavi e prese che devo essere collegati. Questi
cavi e prese sono solitamente collegati uno ad uno ai connettori situati sulla scheda madre. E’ necessario
prestare particolare attenzione a qualunque orientamento del collegamento che possono avere i cavi e, se
necessario, notare la posizione del primo pin del connettore. Si installeranno alcuni adattatori per
particolari necessità quali l’adattatore SCSI, AGP, eccetera. Quando si installano gli adattatori sugli slot
della scheda madre, si ricorda di fissarli con le viti anche sul pannello posteriore del telaio.
Per informazioni dettagliate si prega di fare riferimento alla versione integrale del Manuale utente.
Collegamento dei connettori d’alimentazione ai connettori ATX12V
Ricordarsi che è necessario spingere con fermezza fino in fondo il connettore della sorgente
d’alimentazione ATX al connettore ATX12V, assicurando così un buon collegamento.
Impostazione BIOS
Quando l’hardware è stato installato completamente, accendere il computer ed andare alla voce BIOS per
impostare i parametri del processore. Per informazioni dettagliate si prega di fare riferimento alla versione
integrale del Manuale utente.
User’s Manual
14
KD7A
Introduction
1-1
Chapter 1. Introduction
1-1. Features & Specifications
1. CPU
•
Supports AMD-K7 Athlon/AthlonXP/Barton Socket A 200/266/333MHz FSB Processors
2. Chipset (VIA KT400A and VT8235CE)
•
•
•
Supports Hi-Speed Universal Serial Bus (USB 2.0)
Supports Advanced Configuration and Power Management Interface (ACPI)
Accelerated Graphics Port connector supports AGP 8X/4X Interface (0.8V/1.5V)
3. Memory
•
•
•
3x 184-pin DIMM sockets
Supports 2 DIMM Un-buffered DDR 333/400 (Max. 2GB)
Supports 3 DIMM Un-buffered DDR 200/266 (Max. 3GB)
4. LAN
•
Onboard 10/100M PCI Fast Ethernet Controller
5. Audio
•
•
Onboard 6-Channel AC 97 CODEC
Professional digital audio interface supports 24-bit S/PDIF Out
6. Internal I/O Connectors
•
•
•
•
•
•
1x AGP slot
5x PCI slots
1x floppy port supports up to 2.88MB
2x Ultra ATA 133/100/66/33 connectors
1x USB header
1x CD-IN, 1x AUX-IN header
7. Back Panel I/O
•
•
•
•
1x PS/2 keyboard, 1x PS/2 mouse
1x Serial port connector, 1x Parallel port connector
1x AUDIO connector (Rear-Left / Rear-Right, Center/Subwoofer, S/PDIF Output, Mic-In,
Line-In, Front-Left/Front-Right)
4x USB, 1x RJ-45 LAN Connector
8. Miscellaneous
•
•
ATX form factor
Hardware Monitoring – Including Fan speed, Voltages, CPU and System temperature
Supports Wake On LAN, Modem, but your ATX power supply 5V standby power must be
able to provide at least a 720mA current capacity. Otherwise, the functions may not work
normally.
Specifications and information contained herein are subject to change without notice.
User’s Manual
1-2
1-2. Layout Diagram
KD7A
Chapter 1
Hardware Setup
2-1
Chapter 2. Hardware Setup
Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or
disconnect the power cord before installing or unplugging any connectors or add-on cards. Failing to do
so may cause the motherboard components or add-on cards to malfunction or damaged.
2-1. Install The Motherboard
Most computer chassis have a base with many mounting holes to allow motherboard to be securely
attached on and at the same time, prevented from short circuits. There are two ways to attach the
motherboard to the chassis base:
1. use with studs
2. or use with spacers
In principle, the best way to attach the board is to
use with studs. Only if you are unable to do this
should you attach the board with spacers. Line up
the holes on the board with the mounting holes on
the chassis. If the holes line up and there are
screw holes, you can attach the board with studs.
If the holes line up and there are only slots, you
can only attach with spacers. Take the tip of the
spacers and insert them into the slots. After doing
this to all the slots, you can slide the board into
position aligned with slots. After the board has been positioned, check to make sure everything is OK
before putting the chassis back on.
ATTENTION: To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they
are already fastened on the chassis base and are without mounting-holes on the motherboard to align with.
2-2. Install CPU and Heatsink
Note
•
Installing a heatsink and cooling fan is necessary for heat to dissipate from your processor.
Failing to install these items may result in overheating and processor damage.
•
The AMD Socket A processor will produce a lot of heat while operating, so you need to use a
large heat sink that is especially designed for the AMD socket A processor. Otherwise, it may
result in overheating and processor damage.
•
If your processor fan and its power cable are not installed properly, never plug the ATX power
cable into the motherboard. This can prevent possible processor damage.
•
Please refer to your processor installation manual or other documentation with your processor for
detailed installation instructions.
User’s Manual
2-2
Chapter 2
This motherboard provides a ZIF (Zero Insertion
Force) Socket 462 to install AMD Socket A CPU.
The CPU you bought should have a kit of
heatsink and cooling fan along with. If that’s not
the case, buy one specially designed for Socket A.
Please refer to the figure shown here to install
CPU and heatsink. (For reference only. Your
Heatsink & Fan Assembly may not be exactly the
same as this one.)
1.
Locate the Socket 462 on this motherboard.
Pull the CPU release lever sideways to
unlatch and then raise it all the way up.
2.
Align the CPU notch to the socket notch for
CPU. Drop the processor with its pin side
down into the CPU socket. Do not use extra
force to insert CPU; it only fit in one
direction. Close the CPU release lever.
3.
Remove the plastic film adhesive on the
heatsink. Make sure the stepped portion of
the heatsink is facing toward the end of the
socket that reads “Socket 462”. Put the
heatsink faces down onto the processor until
it covers the processor completely.
4.
Push down the short end of the retaining clip
first to lock up with the center lug at the
bottom of the socket.
5.
Use a screwdriver to insert into the slot at the
long end of the retaining clip. Push the clip
downward to lock up with the center lug at
the top of the socket. The heatsink & fan
assembly is now firmly attached on the CPU
socket.
6.
Attach the fan connector of Heatsink & Fan
Assembly with the fan connector on the
motherboard.
ATTENTION: Do not forget to set the correct
bus frequency and multiple for your processor.
KD7A
Hardware Setup
2-3
2-3. Install System Memory
This motherboard provides 3 184-pin DDR DIMM sites for memory expansion available from minimum
128MB to maximum 3GB.
Table 2-1. Valid Memory Configurations
Bank
Memory Module
Total Memory
Bank 0, 1 (DIMM1)
128, 256, 512MB, 1GB
128MB ~ 1GB
Bank 2, 3 (DIMM2)
128, 256, 512MB, 1GB
128MB ~ 1GB
Bank 4, 5 (DIMM3)
128, 256, 512MB, 1GB
128MB ~ 1GB
Total System Memory for Un-buffered DDR 200/266 DIMM
128MB ~ 3GB
Total System Memory for Un-buffered DDR 333/400 DIMM
128MB ~ 2GB
NOTE: It is necessary to install one DIMM module at least from memory slot DIMM1.
Power off the computer and unplug the AC power cord before installing or removing memory modules.
1.
Locate the DIMM slot on the board.
2.
Hold two edges of the DIMM module
carefully, keep away of touching its
connectors.
3.
Align the notch key on the module with the
rib on the slot.
4.
Firmly press the module into the slots until
the ejector tabs at both sides of the slot
automatically snaps into the mounting notch.
Do not force the DIMM module in with extra
force as the DIMM module only fit in one direction.
5.
To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and
then pull out the DIMM module.
ATTENTION: Static electricity can damage the electronic components of the computer or optional
boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a
grounded metal object briefly.
User’s Manual
2-4
Chapter 2
2-4. Connectors, Headers and Switches
Here we will show you all of the connectors, headers and switches, and how to connect them. Please read
the entire section for necessary information before attempting to finish all the hardware installation inside
the computer chassis. A complete enlarged layout diagram is shown in Chapter 1 for all the position of
connectors and headers on the board that you may refer to.
WARNING: Always power off the computer and unplug the AC power cord before adding or removing
any peripheral or component. Failing to so may cause severe damage to your motherboard and/or
peripherals. Plug in the AC power cord only after you have carefully checked everything.
(1).
ATX Power Input Connectors
This motherboard provides two power connectors to connect to an ATX12V power supply with 300W,
20A +5VDC, and 720mA +5VSB capacity at least.
KD7A
Hardware Setup
(2).
2-5
FAN Connectors
These 3-pin connectors each provide power to the cooling fans installed in your system.
The CPU must be kept cool by using a powerful fan with heatsink. The system is capable of monitoring
the speed of the CPU fan.
•
CPUFAN1: CPU Fan
•
NBFAN1: Chipset Fan
•
SYSFAN1: System Fan
•
AUXFAN1, AUXFAN2: Auxiliary Fan
WARNING: These fan connectors are not jumpers. DO NOT place jumper caps on these connectors.
User’s Manual
2-6
(3).
Chapter 2
CMOS Memory Clearing Header
This header uses a jumper cap to clear
the CMOS memory.
•
Pin 1-2 shorted (default):
Normal operation.
•
Pin 2-3 shorted: Clear CMOS
memory.
WARNING: Turn the power off first
(including the +5V standby power)
before clearing the CMOS memory.
Failing to do so may cause your
system to work abnormally or
malfunction.
(4).
S2K Mode Select Header
This header uses a jumper to select the S2K mode.
Short pin-2 and pin-3 for “Strapping from Hardware” to allow the CPU hardware controls the timing of
S2K bus for a better system flexibility.
The default setting is pin-1 and pin-2 shorted for “Strapping from boot ROM” to allow the internal boot
ROM controls the timing of S2K bus.
KD7A
Hardware Setup
(5).
2-7
Wake-up Header
These headers use a jumper cap to enable/disable the wake-up function.
•
PS2-PWR1:
Pin 1-2 shorted (default): Disable wake-up function support at Keyboard/Mouse port.
Pin 2-3 shorted: Enable wake-up function support at Keyboard/Mouse port
•
USB-PWR1:
Pin 1-2 shorted (default): Disable wake-up function support at USB1 port.
Pin 2-3 shorted: Enable wake-up function support at USB1 port.
•
USB-PWR2:
Pin 1-2 shorted (default): Disable wake-up function support at USB2 port.
Pin 2-3 shorted: Enable wake-up function support at USB2 port
User’s Manual
2-8
(6).
Chapter 2
Front Panel Switches & Indicators Headers
This header is used for connecting switches and LED indicators on the chassis front panel.
Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below
stands for positive polarity for the LED connection. Please pay attention to connect these headers. A
wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could
cause system malfunction.
•
HLED (Pin 1, 3):
Connects to the HDD LED cable of chassis front panel.
•
RST (Pin 5, 7):
Connects to the Reset Switch cable of chassis front panel.
•
SPK (Pin 15, 17, 19, 21):
Connects to the System Speaker cable of chassis.
•
SLED (Pin 2, 4):
Connects to the Suspend LED cable (if there is one) of chassis front panel.
•
PWR-ON (Pin 6, 8):
Connects to the Power Switch cable of chassis front panel.
•
PLED (Pin 16, 18, 20):
Connects to the Power LED cable of chassis front panel.
KD7A
Hardware Setup
(7).
2-9
Additional USB Port Headers
This header provides 2 additional USB 2.0 ports connection through an USB cable designed for USB 2.0
specifications.
Pin
Pin Assignment
Pin
Pin Assignment
1
VCC
2
VCC
3
Data0 -
4
Data1 -
5
Data0 +
6
Data1 +
7
Ground
8
Ground
9
NC
10
NC
User’s Manual
2-10
(8).
Chapter 2
Front Panel Audio Connection Header
This header provides the connection to audio connector at front panel.
•
To use the audio connector at front panel, remove all the jumpers on this header, and then connect
to front panel by the extenson cable provided with the chassis.
•
To use the audio connector at rear panel, disconnect the extension cable, attach the jumpers back at
pin 5-6, and pin 9-10 (default setting).
Pin
1
3
5
7
9
11
13
KD7A
Pin Assignment
Audio Mic.
Audio Mic. Bias
Speaker Out Right
Channel
X
Speaker Out Left
Channel
Ground
VCC
Pin
2
4
6
8
10
12
14
Pin Assignment
Ground
VCC
Speaker Out Right
Channel Return
NC
Speaker Out Left
Channel Return
S/PDIF In
S/PDIF Out
Hardware Setup
(9).
2-11
Internal Audio Connectors
These connectors connect to the audio output of internal CD-ROM drive or add-on card.
(10). Accelerated Graphics Port Slot
This slot supports an optional AGP graphics card up to AGP 8X mode. Please refer to our Web site for
more information on graphics cards.
ATTENTION: This motherboard does not support 3.3V AGP cards. Use only 1.5V or 0.8V AGP cards.
User’s Manual
2-12
Chapter 2
(11). Floppy Disk Drive Connector
This connector supports two standard floppy disk drives via a 34-pin 34-conductor ribbon cable.
Connecting the Floppy Disk Drive Cable:
1.
Install one end of the ribbon cable into the FDC1 connector. The colored edge of the ribbon cable
should be aligned with pin-1 of FDC1 connector.
2.
Install the other end(s) of ribbon cable into the disk drive connector(s). The colored edge of the
ribbon cable should be also aligned with pin-1 of disk drive connector. The endmost connector
should be attached to the drive designated as Drive A.
KD7A
Hardware Setup
2-13
(12). IDE Connectors
This motherboard provides two IDE ports to connect up to four IDE drives at Ultra ATA/100 mode by
Ultra ATA/66 ribbon cables. Each cable has 40-pin 80-conductor and three connectors, providing two
hard drives connection with motherboard. Connect the single end (blue connector) at the longer length of
ribbon cable to the IDE port on motherboard, and the other two ends (gray and black connector) at the
shorter length of the ribbon cable to the connectors on hard drives.
If you want to connect two hard drives together through one IDE channel, you must configure the second
drive to Slave mode after the first Master drive. Please refer to the drives’ documentation for jumper
settings. The first drive connected to IDE1 is usually referred to as “Primary Master”, and the second
drive as “Primary Slave”. The first drive connected to IDE2 is referred to as “Secondary Master” and the
second drive as “Secondary Slave”.
Keep away from connecting one legacy slow speed drive, like CD-ROM, together with another hard drive
on the same IDE channel; this will drop your integral system performance.
User’s Manual
2-14
Chapter 2
(13). Back Panel Connectors
•
Mouse: Connects to PS/2 mouse.
•
Keyboard: Connects to PS/2 keyboard.
•
LPT1: Connects to printer or other devices that support this communication protocol.
•
COM1: Connects to external modem, mouse or other devices that support this communication
protocol.
•
AUDIO1:
R.L./R.R. (Rear Left / Rear Right): Connects to the rear left and rear right channel in the 5.1
channel audio system.
Cen./Sub. (Center / Subwoofer): Connects to the center and subwoofer channel in the 5.1 channel
audio system.
S/PDIF Out: This connector provides an S/PDIF out connection through optical fiber to digital
multimedia devices.
Mic In: Connects to the plug from external microphone.
Line In: Connects to the line out from external audio sources.
F.L./F.R. (Front Left / Front Right): Connects to the front left and front right channel in the
5.1-channel or regular 2-channel audio system.
•
LAN: Connects to Local Area Network.
•
USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse,
keyboard, hub, digital camera, joystick etc.
KD7A
BIOS Setup
3-1
Chapter 3. BIOS Setup
This motherboard provides a programmable EEPROM that you can update the BIOS utility. The BIOS
(Basic Input/Output System) is a program that deals with the basic level of communication between
processor and peripherals. Use the BIOS Setup program only when installing motherboard, reconfiguring
system, or prompted to “Run Setup”. This chapter explains the Setup Utility of BIOS utility.
After powering up the system, the BIOS message appears on the screen, the memory count begins, and
then the following message appears on the screen:
PRESS DEL TO ENTER SETUP
If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt> + <Del>
keys, or by pressing the Reset button on computer chassis. Only when it failed by these two methods can
you restart the system by powering it off and then back on.
After pressing <Del> key, the main menu screen appears.
NOTE: In order to increase system stability and performance, our engineering staffs are constantly
improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for
your reference only, may not completely match what you see on your screen.
User’s Manual
3-2
Chapter 3
3-1. SoftMenu Setup
The SoftMenu utility is ABIT’s exclusive and ultimate solution in programming the CPU operating speed.
All the parameters regarding CPU FSB speed, multiplier factor, the AGP & PCI clock, and even the CPU
core voltage are all available at your fingertips.
CPU Name Is:
This item displays the CPU model name, for example: AMD Athlon(tm) XP.
CPU Operating Speed:
This item displays the CPU operating speed according to the type and speed of your CPU. You can also
select the [User Define] option to enter the manual option.
User Define:
WARNING: The wrong settings of the multiplier and external clock in certain circumstances may cause
CPU damage. Setting the working frequency higher than the PCI chipset or processor specs, may cause
abnormal memory module functioning, system hangs, hard disk drive data lose, abnormal functioning of
the VGA card, or abnormal functioning with other add-on cards. Using non-specification settings for your
CPU is not the intention of this explanation. These should be used for engineering testing, not for normal
applications.
There will be no guaranty for the settings beyond specification, any damage of any component on this
motherboard or peripherals result therein is not our responsibility.
CPU FSB Clock (MHz):
This item sets the CPU Front Side Bus speed from 100 to 250. Due to the specification limit of the CPU
you installed, the speed you set over its standard bus speed is supported, but not guaranteed.
Ratio (FSB:AGP:PCI):
This item sets the ratio among the clock of FSB, AGP, and PCI. Take the 4:2:1ratio for instance, if the
FSB clock is 133MHz (133 x 4/4), the AGP clock will be 66MHz (133 x 2/4), and the PCI clock will be
33MHz (133 x 1/4).
KD7A
BIOS Setup
3-3
Multiplier Factor:
This item sets the multiplier factor for the CPU you installed.
NOTE: Some processors might have this multiplier factor locked, so there is no way to choose a higher
multiplier factor.
Power Supply:
This option allows you to switch between CPU default and user-defined voltages. Leave this setting to
default unless the current CPU type and voltage setting cannot be detected or is not correct. The option
“User Define” enables you to select the Core Voltage manually.
CPU Core Voltage:
This item selects the CPU core voltage.
ATTENTION: A wrong voltage setting may cause the system unstable or even damage the CPU. Please
leave it to default settings unless you are fully aware of its consequences.
AGP Voltage:
This item selects the voltage for AGP slot.
DDR Voltage:
This item selects the voltage for DRAM slot.
NB Core Voltage:
This item selects the NB core voltage.
CPU Fast Command Decode:
Two options are available: at Normal to Fast or at Fast to Normal. This will depends which state
you choose. If you set this item from “at Fast” to “to Normal”, when you reboot the system and finish
the POST process, the state will change to your new setting (Here’s to Normal). After that, if you go to
view the BIOS menu again, you will see this item shows “at Normal”, if you press the <Enter> key,
you’ll see the two options: at Normal to Fast, and the default setting is at Normal. If you set this item
from “at Normal” to “to Fast”, and go through the same process we mentioned before, you will see this
item shows “at Fast”, if you press the <Enter> key, you’ll see the two options: at Fast to Normal, and
the default setting is at Fast. You can select item if you want CPU decode address is faster or normal
speed. We suggest you choose to Normal for greatest stability. Should you want increased performance
then you can select to Fast. You have to set the jumper on the motherboard called “CROM” pin 1 and pin
2 short, then you can see this item appear in this menu.
User’s Manual
3-4
Chapter 3
3-2. Standard CMOS Features
This section contains the basic configuration parameters of the BIOS. These parameters include date,
hour, VGA card, FDD and HDD settings.
Date (mm:dd:yy):
This item sets the date you specify (usually the current date) in the format of [Month], [Date], and [Year].
Time (hh:mm:ss):
This item sets the time you specify (usually the current time) in the format of [Hour], [Minute], and
[Second].
IDE Primary Master / Slave and IDE Secondary Master / Slave:
Click <Enter> key to enter its submenu:
IDE HDD Auto-Detection:
This item allows you to detect the parameters of IDE drives by pressing <Enter> key. The parameters will
be shown on the screen automatically.
KD7A
BIOS Setup
3-5
IDE Primary Master / Slave and IDE Secondary Master / Slave:
When set to [Auto], the BIOS will automatically check what kind of IDE drive you are using. If you want
to define your own drive by yourself, set it to [Manual] and make sure you fully understand the meaning
of the parameters. Please refer to the instruction manual provided by the device’s manufacturer to get the
setting right.
Access Mode:
This item selects the mode to access your IDE devices. Leave this item to its default [Auto] setting to
detect the access mode of your HDD automatically.
Capacity:
This item displays the approximate capacity of the disk drive. Usually the size is slightly greater than the
size of a formatted disk given by a disk-checking program.
Cylinder:
This item configures the numbers of cylinders.
Head:
This item configures the numbers of read/write heads.
Precomp:
This item displays the number of cylinders at which to change the write timing.
Landing Zone:
This item displays the number of cylinders specified as the landing zone for the read/write heads.
Sector:
This item configures the numbers of sectors per track.
Back to Standard CMOS Features Setup Menu:
Drive A & Drive B:
This item sets the type of floppy drives (usually only Drive A) installed.
Floppy 3 Mode Support:
This item allows you to use “3 Mode Floppy Drive” in Japanese computer system by selecting drive A, B,
or both. Leave this item to its default [Disabled] setting if you are not using this Japanese standard floppy
drive.
Video:
This item selects the type of video adapter used for the primary system monitor.
User’s Manual
3-6
Chapter 3
[EGA/VGA]: (Enhanced Graphics Adapter/Video Graphics Array) For EGA, VGA, SVGA and PGA
monitor adapters.
[CGA 40]: (Color Graphics Adapter) Power up in 40-column mode.
[CGA 80]: (Color Graphics Adapter) Power up in 80-column mode.
[Mono]: (Monochrome adapter) Includes high-resolution monochrome adapters.
Halt On:
This item determines whether the system stops if an error is detected during system boot-up.
[All Errors]: The system-boot will stop whenever the BIOS detect a non-fatal error.
[No Errors]: The system-boot will not stop for any error detected.
[All, But Keyboard]: The system-boot will stop for all errors except a keyboard error.
[All, But Diskette]: The system-boot will stop for all errors except a diskette error.
[All, But Disk/Key]: The system-boot will stop for all errors except a diskette or keyboard error.
Base Memory:
This item displays the amount of base memory installed in the system. The value of the base memory is
typically 640K for system with 640K or more memory size installed on the motherboard.
Extended Memory:
This item displays the amount of extended memory detected during system boot-up.
Total Memory:
This item displays the total memory available in the system.
KD7A
BIOS Setup
3-7
3-3. Advanced BIOS Features
Hard Disk Boot Priority:
This item selects the hard disks booting priority. By pressing <Enter> key, you can enter its submenu
where the hard disks detected can be selected for the booting sequence to boot up system.
This item functions only when there is the option of [Hard Disk] in any one of the First/Second/Third
Boot Device items.
Virus Warning:
When set to [Enabled], the BIOS will monitor the boot sector and partition table of the hard disk drive. If
there is any attempt of writing to the boot sector or partition table of the hard disk drive, the BIOS will
halt the system and an error message will appear.
USB Flash Disk Type:
This item selects the type for your USB flash disk.
First Boot Device / Second Boot Device / Third Boot Device / Boot Other Device:
Select the drive to boot first, second and third in the [First Boot Device], [Second Boot Device], and
[Third Boot Device] items respectively. The BIOS will boot the operating system according to the
sequence of the drive selected. Set [Boot Other Device] to [Enabled] if you wish to boot from another
device other than these three items.
Swap Floppy Drive:
When set to [Enabled], and the system is booting from the floppy drive, the system will boot from drive B
instead of the regular drive A. There must be two floppy drives connected in the system to use this
function.
Boot Up Floppy Seek:
When set to [Enabled], the BIOS will check whether the floppy disk drive is installed or not.
User’s Manual
3-8
Chapter 3
Boot Up NumLock Status:
This item determines the default state of the numeric keypad at system booting up.
[On]: The numeric keypad functions as number keys.
[Off]: The numeric keypad functions as arrow keys.
Typematic Rate Setting:
This item allows you to adjust the keystroke repeat rate. When set to Enabled, you can set the two
keyboard typematic controls that follow (Typematic Rate and Typematic Rate Delay). If this item is set to
Disabled, the BIOS will use the default setting. The default setting is Enabled.
Typematic Rate (Chars/Sec):
When you press a key continuously, the keyboard will repeat the keystroke according to the rate you have
set (Unit: characters/second). Eight options are available: 6 8 10 12 15 20 24 30 Back to 6. The default setting is 30.
Typematic Delay (Msec):
When you press a key continuously, if you exceed the delay you have set here, the keyboard will
automatically repeat the keystroke according to a certain rate (Unit: milliseconds). Four options are
available: 250 500 750 1000 Back to 250. The default setting is 250.
Security Option:
This item determines when the system will prompt for password - every time the system boots or only
when enters the BIOS setup.
[Setup]: The password is required only when accessing the BIOS Setup.
[System]: The password is required each time the computer boots up.
NOTE: Don’t forget your password. If you forget the password, you will have to open the computer case
and clear all information in the CMOS before you can start up the system. But by doing this, you will
have to reset all previously set options.
APIC Mode:
Leave this item to its default setting.
MPS Version Ctrl For OS:
This item specifies which version of MPS (Multi-Processor Specification) this motherboard will use. The
options are 1.1 and 1.4. The default setting is 1.4. If you use an older OS for dual processor executing,
please set this option to 1.1.
OS Select For DRAM > 64MB:
This item allows you to access the memory that is over 64MB in OS/2. Leave this item to its default
[Non-OS2] setting for operating system other than OS/2.
KD7A
BIOS Setup
3-9
Report No FDD For OS:
When set to [Enabled], this item allows you to run some older operating system without floppy disk drive.
Leave this item to its default setting.
Delay IDE Initial (Secs):
This item allows the BIOS to support some old or special IDE devices by prolonging this delay time. A
larger value will give more delay time to the device for which to initialize and to prepare for activation.
Disable Unuse DIMM/PCI Clk:
This option disables the clock of DIMM/PCI slot that is not in use.
[Yes]: The system automatically detect the unused DIMM and PCI slots, and stop sending clock signal to
these unused PCI slots.
[No]: The system always send clock signal to all PCI slots.
NOTE: Set this option to [No] setting if there are adapters that cannot be automatically detected by the
system and will cause malfunction.
User’s Manual
3-10
Chapter 3
3-4. Advanced Chipset Features
DRAM Clock/Drive Control:
Click <Enter> key to enter its submenu:
Current FSB Frequency:
This item will show you the current system front side bus speed.
Current DRAM Frequency:
This item will show you the current DRAM bus speed.
DRAM Clock:
This item sets the DRAM clock of your DRAM module. The system may be unstable or unable to boot up
if your DRAM module does not support the clock you set.
When set to [By SPD], the BIOS will read the DRAM module SPD data and automatically set the DRAM
clock by the value stored in it.
NOTE: This item will be unchangeable at 333MHz FSB.
KD7A
BIOS Setup
3-11
DRAM Timing Selectable:
Four options are available: Manual By SPD Turbo Ultra. The default setting is By SPD. When
set to “By SPD”, the BIOS will read the DRAM module SPD data and automatically set to the values
stored in it. If you set to “Manual”, the following five items will be available to let you make
adjustments.
CAS Latency Time:
Four options are available: 1.5 2 2.5 3. The default setting is 2.5. You can select SDRAM CAS
(Column Address Strobe) latency time according your SDRAM specification.
Bank Interleave:
Three options are available: Disabled 2 Way 4 Way. The default setting is Disabled. Depending on
your SDRAM module structure, the 4-Way setting can offer the best performance. If you choose the
wrong setting, the computer system will not run in a stable manner. For detailed information on your
SDRAM module, please ask your SDRAM module manufacturer.
Precharge to Active (Trp):
Trip timing value (Precharge time – time from precharge command to when back can be activated).
Active to Precharge (Tras):
Tras timing value = Minimum bank active time from activate to precharge of same bank.
Active to CMD (Trcd):
Trcd timing value = RAS to CAS latency + rd/wr command delay
DRAM Burst Length
DDR SDRAM modules provide a Burst mode that means an auto precharge function for programmable
READ or WRITE burst lengths of 4 or 8 locations.
This means that if we set burst length to 8, the address bus will acesss 8 bytes each cycle to precharge,
etc.
DRAM Command Rate:
Two options are available: 2T Command or 1T Command. The default setting is 2T Command. When the
host (northbridge) locates the desired memory address, it then processes the wait state of commands. Set
it to 2T Command for system compatibility or to 1T Command for system performance.
Write Recovery Time:
Two options are available: 2T or 3T. The default setting is 3T. This is the period between two write times.
DDR400 tWTR timing control
Two options are available: 1T or 2T. The default setting is 2T. This is the Internal WRITE to READ
command delay time period.
User’s Manual
3-12
Chapter 3
DDR DQS Input Delay:
Two options are available: Auto or Manual. The default setting is Auto. If you set to Manual, then the
next item will be available.
Input Delay Value:
This item allows you to adjust the data input strobe delay time of memory. You can key in the HEX
number into this section.
DDR DQS Output Delay:
Two options are available: Auto or Manual. The default setting is Auto. If you set to Manual, then the
next item will be available.
Output Delay Value:
This item allows you to adjust the data output strobe delay time of memory. You can key in the HEX
number into this section.
Back to Advanced Chipset Features Setup Menu:
AGP & P2P Bridge Control:
Click <Enter> key to enter its submenu:
CPU to AGP Post Write:
Leave this item to its default setting.
AGP Aperture Size:
This option specifies the amount of system memory that can be used by the AGP device. The aperture is a
portion of the PCI memory address range dedicated for graphics memory address space.
AGP Data Transfer Rate:
This item selects the data transfer rate of AGP device. A higher rate delivers faster and better graphics to
your system. Make sure your graphics card supports the mode you select.
KD7A
BIOS Setup
3-13
AGP Fast Write:
Two options are available: Disabled Enabled. The default setting is Disabled. If your AGP adapter can
support this function, then you can choose Enabled. Otherwise, choose Disabled.
AGP Master 1 WS Write:
Two options are available: Disabled Enabled. The default setting is Disabled. This implements a
single delay when writing to the AGP Bus. When you set it to Enabled, two-wait states are used by the
system, allowing for greater stability.
AGP Master 1 WS Read:
Two options are available: Disabled Enabled. The default setting is Disabled. This implements a
single delay when reading to the AGP Bus. When you set it to Enabled, two-wait states are used by the
system, allowing for greater stability.
AGP 3.0 Calibration cycle:
Leave this item to its default setting.
AGP Driving Control:
Leave this item to its default setting.
AGP Driving Value:
Leave this item to its default setting.
AGP Pad Drive Delay:
Leave this item to its default setting.
AGP Strob Drive Strength:
Leave this item to its default setting.
Back to Advanced Chipset Features Setup Menu:
CPU & PCI Bus Control:
Click <Enter> key to enter its submenu:
User’s Manual
3-14
Chapter 3
PCI Master 0 WS Write:
Two options are available: Enabled or Disabled. The default setting is Enabled. When Enabled, writes to
the PCI bus are executed with zero wait state (immediately) when PCI bus is ready to receive data. If it is
set to Disabled, the system will wait one state before data is written to the PCI bus.
PCI Master 0 WS Read:
Two options are available: Enabled or Disabled. The default setting is Enabled. When Enabled, reads to
the PCI bus are executed with zero wait state (immediately) when PCI bus is ready to receive data. If it is
set to Disabled, the system will wait one state before data is written to the PCI bus.
CPU to PCI Post Write
Two options are available: Enabled or Disabled. The default is Enabled, When Enable, data transmission
from CPU to PCI bus are buffered and compensate for the different speed between CPU and PCI bus. If it
is set to Disabled, data transmissions are not buffered and CPU must wait until the data transmission is
complete and then start another transmission cycle.
Vlink 8X Support:
Two options are available: Disabled or Enabled. The default setting is Enabled. This item can let you
enable the Vlink bus data transfer between northbridge and southbridge.
PCI Delay Transaction:
Two options are available: Disabled or Enabled. The default setting is Enabled. The chipset has an
embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support
compliance with PCI specification version 2.2.
KD7A
BIOS Setup
3-15
3-5. Integrated Peripherals
OnChip IDE Device:
Click <Enter> key to enter its submenu:
IDE Prefetch Mode:
Two options are available: Disabled or Enabled. The default setting is Enabled. The onboard IDE drive
interfaces supports IDE prefetching for faster drive accesses. If you install a primary and/or secondary
add-in IDE interface, set this field to Disabled if the interface does not support prefetching.
OnChip IDE-1 Controller:
This item allows you to enable or disable the primary and secondary IDE controller. Select [Disabled] if
you want to add a different hard drive controller.
Master/Slave Drive PIO Mode
The PIO (Programmed Input/Output) mode allows the BIOS to tell the controller what it wants and then
let the controller and the CPU perform the complete task, rather than having the BIOS issue a series of
commands to affect a transfer to or from the disk drive.
[Auto]: The BIOS will select the best available mode after checking your disk drive.
User’s Manual
3-16
Chapter 3
[Mode 0-4]: You can select a mode that matches your disk drive’s timing. Do not use the wrong setting
or you will have drive errors.
Master/Slave Drive Ultra DMA
This item allows you to set the Ultra DMA in use.
[Auto]: The BIOS will select the best available option after checking your hard drive or CD-ROM.
[Disabled]: The BIOS will not detect these categories. If problem arises in using Ultra DMA devices, try
disabling this item.
OnChip IDE-2 Controller:
The description is same as the OnChip IDE-1 Controller.
Back to Integrated Peripherals Setup Menu:
OnChip PCI Device:
Click <Enter> key to enter its submenu:
OnChip Audio Controller:
This option enables or disables the audio controller.
OnChip LAN Controller:
This option enables or disables the LAN controller.
OnChip LAN Boot ROM:
This item enables or disables the Boot ROM on LAN controller.
OnChip USB Controller:
This option enables or disables the USB controller.
USB Keyboard Support Via:
This item allows you to select [BIOS] for using USB keyboard in DOS environment, or [OS] in OS
environment.
KD7A
BIOS Setup
3-17
USB Mouse Support Via:
This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS
environment.
USB 2.0 Controller:
This option enables or disables the USB 2.0 controller.
Back to Integrated Peripherals Setup Menu:
SuperIO Device:
Click <Enter> key to enter its submenu:
Onboard Serial Port 1:
This is used to specify the I/O address and IRQ of Serial Port 1. Six options are available: Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 AUTO. The default setting is 3F8/IRQ4.
Onboard Parallel Port:
Sets the I/O address and IRQ of the onboard parallel port. Four options are available: Disable 378/IRQ7 278/IRQ5 3BC/IRQ7. Default setting is 378/IRQ7.
Parallel Port Mode: Four options are available: SPP EPP ECP ECP+EPP. The default setting
is ECP+EPP mode.
EPP Mode Select: Two options are available: EPP1.7 EPP1.9. The default setting is EPP 1.7. When
the mode selected for the parallel port mode is EPP, the two EPP version options are available.
ECP Mode Use DMA: Two options are available: 1 3. The default setting is 3. When the mode
selected for the parallel port mode is ECP, the DMA channel selected can be Channel 1 or Channel 3.
Back to Integrated Peripherals Setup Menu:
Init Display First:
This item selects to initialize AGP or PCI Slot first when the system boots.
[AGP]: When the system boots, it will first initialize AGP.
User’s Manual
3-18
Chapter 3
[PCI Slot]: When the system boots, it will first initialize PCI.
Onboard FDD Controller:
Two options are available: Enabled and Disabled. The default setting is Enabled. You can enable or
disable the onboard FDD controller.
KD7A
BIOS Setup
3-19
3-6. Power Management Setup
ACPI Suspend Type:
This item selects the type of Suspend mode.
[S1(PowerOn Suspend)]: Enables the Power On Suspend function.
[S3(Suspend To RAM)]: Enables the Suspend to RAM function.
MODEM Use IRQ:
You can specify the IRQ for modem use. Eight options are available: NA 3 4 5 7 9 10
11. The default setting is NA.
Power Button Function:
This item selects the method of powering off your system:
[Delay 4 Sec.]: Pushing the power button for more than 4 seconds will power off the system. This will
prevent the system from powering off in case you accidentally hit or pushed the power button.
[Instant-Off]: Pressing and then releasing the power button at once will immediately power off the
system.
Run VGABIOS if S3 Resume:
Three options are available: Auto Yes No. The default setting is Auto. This item can let you choose
when S3 resume active, the VGA BIOS need to be initiative or not.
Restore On AC Power Loss:
This item selects the system action after an AC power failure.
[Power Off]: When power returns after an AC power failure, the system’s power remains off. You must
press the Power button to power-on the system.
[Power On]: When power returns after an AC power failure, the system’s power will be powered on
automatically.
User’s Manual
3-20
Chapter 3
[Last State]: When power returns after an AC power failure, the system will return to the state where you
left off before power failure occurs. If the system’s power is off when AC power failure occurs, it will
remain off when power returns. If the system’s power is on when AC power failure occurs, the system
will power-on when power returns.
IRQ/Event Activity Detect:
Click <Enter> key to enter its submenu:
Power On Function:
Four options are available: Hot Key Password Mouse Button Only. The default setting is Button
Only. This iten allow you to choose the computer power turn on method you like. Some item you choose,
some of the following items will be available to let you making further setting. For instance, when you set
this item to Password, the item of “KB Power On Password” will allow you to enter password. When
you set this item to Hot Key, the item of “Hot Key Power On” will allow you to choose the hot key you
want. If you choose Mouse, you can press any key on mouse to turn on the computer power.
NOTE: To enable this “Power On” function, the wake-up header of [PS2-PWR1], [USB-PWR1],
[USB-PWR2] must be set to [Enabled] position. Please refer to the configuration of “Wake-up Header”
[PS2-PWR1], [USB-PWR1], and [USB-PWR2] in section 2-4, chapter 2.
The mouse wake up function can only be used with the PS/2 mouse, not with the COM port or USB type.
Some PS/2 mice cannot wake up the system because of compatible problems. If the specs of your
keyboard are too old, it may fail to power on.
KB Power On Password:
When you perss the <Enter> key, then you can enter the password you want. When set be done, you need
to saving and leave the BIOS setting menu to reboot your computer system. Next time when you
shutdown your computer, you can’t use the power button to turn on the computer power anymore.
You need to press the password to turn on your computer power.
Hot Key Power On:
Fifteen options are available: Ctrl+F1 ~ Ctrl+F12, Power, Wake and Any Key. The default setting is
Ctrl+F1. You can choose the hot key that you want it to turn on your computer power.
PS2MS Wakeup:
This item controls the PS2 mouse to wake up the system that has been powered down.
KD7A
BIOS Setup
3-21
Resume by OnChip USB:
Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled,
any event affecting from onchip USB will awaken a system that has powered down.
VGA:
Two items available: OFF or ON. The default setting is OFF. When set to ON, any event occurring at a
VGA port will awaken a system that has powered down.
LPT & COM:
Four items are available: NONE LPT COM LPT/COM. The default setting is LPT/COM. When
set to LPT/COM, any event occurring at a LPT (printer) or COM (serial) port will awaken a system that
has powered down.
HDD & FDD:
Two items are available: OFF or ON. The default setting is ON. When set to ON, any event affecting a
hard disk drive or floppy drive port will awaken a system that has powered down.
PCI Master:
Two items are available: OFF or ON. The default setting is OFF. When set to ON, any event affecting the
PCI Master signal will awaken a system that has powered down.
Wakeup by PME# of PCI:
Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled,
any event affecting from PCI card (PME) will awaken a system that has powered down.
Resume by Ring:
Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled,
any event affecting from Modem Ring will awaken a system that has powered down.
Wakeup by Alarm:
Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled,
you can set the date and time at which the RTC (real-time clock) alarm awakens the system from Suspend
mode.
Date (of Month) / Resume Time (hh:mm:ss):
You can set the Date (month) Alarm and Time Alarm (hh:mm:ss). Any event occurring will awaken a
system that has powered down.
User’s Manual
3-22
Chapter 3
IRQ Activity Monitroing:
Click <Enter> key to enter its submenu:
All Interrupt Event:
Two items available: Off or Manual. The default setting is Manual. When you set this item to Manual, the
following IRQ events will be available for adjustment.
When set to Disabled, activity will neither prevent the system from going into a power management mode
nor awaken it. Each item has two options: Enabled Disabled.
KD7A
BIOS Setup
3-23
3-7. PnP/PCI Configurations
Force Update ESCD:
If you want to clear ESCD data next time you boot up, and ask the BIOS to reset the settings for the Plug
& Play ISA Card and the PCI Card, select Enabled. But the next time you boot up, this option will
automatically be set as Disabled.
NOTE: The ESCD (Extended System Configuration Data) contains the IRQ, DMA, I/O port, memory
information of the system. This is a specification and a feature specific to the Plug & Play BIOS.
Resources Controlled By:
This item configures all of the boot and Plug-and-Play compatible devices.
[Auto(ESCD)]: The system will automatically detect the settings.
[Manual]: Choose the specific IRQ resources in the “IRQ Resources” menu.
IRQ Resources:
Click <Enter> key to enter its submenu:
This item sets each system interrupt to either [PCI Device] or [Reserved].
User’s Manual
3-24
Chapter 3
Back to PnP/PCI Configurations Setup Menu:
PCI/VGA Palette Snoop:
This item determines whether the MPEG ISA/VESA VGA cards can work with PCI/VGA or not.
[Enabled]: MPEG ISA/VESA VGA cards work with PCI/VGA.
[Disabled]: MPEG ISA/VESA VGA cards do not work with PCI/VGA.
Allocate IRQ To Video:
This item assigns an IRQ for the VGA card installed.
[Enabled]: Automatically assign an IRQ for the VGA card installed.
[Disabled]: The IRQ that was previously occupied by the VGA card will be available for new device.
Allocate IRQ To USB:
This item assigns an IRQ for the USB device connected.
[Enabled]: Automatically assign an IRQ for the USB device connected.
[Disabled]: The IRQ that was previously occupied by the USB device connected will be available for
new device.
PIRQ_0 Use IRQ No. ~ PIRQ_3 Use IRQ No.:
This item specifies the IRQ number manually or automatically for the devices installed on PCI slots.
For the relations between the hardware layout of PIRQ (the signals from the VIA VT8235 chipset), INT#
(means PCI slot IRQ signals) and devices, please refer to the table below:
Signals
PIRQ_0 Assignment
PIRQ_1 Assignment
PIRQ_2 Assignment
PIRQ_3 Assignment
AGP
LAN PCI-1
INT A INT A INT A
INT B
INT B
INT C
INT D
PCI-2
INT D
INT A
INT B
INT C
PCI-3
INT C
INT D
INT A
INT B
PCI-4
INT B
INT C
INT D
INT A
PCI-5
INT D
INT C
INT B
INT A
NOTE:
•
PCI slot 1 shares IRQ signals with AGP slot, and LAN.
•
PCI slot 4 shares IRQ signals with PCI slot 5.
•
If you want to install two PCI cards into those PCI slots that share IRQ with one another at the same
time, you must make sure that your OS and PCI devices’ driver supports the IRQ sharing function.
KD7A
BIOS Setup
3-25
3-8. PC Health Status
CPU Shutdown Temperature:
This item sets the temperature that would shutdown the system automatically in order to prevent system
overheats.
CPU Warning Temperature:
This item selects the CPU’s warning temperature limit. Once the system has detected that the CPU’s
temperature exceeded the limit, warning beeps will sound.
NOTE: The onboard hardware monitor function is capable of detecting these system health conditions. If
you want a warning message to pop-up or a warning alarm to sound when an abnormal condition occurs,
you must install the “Hardware Doctor” utility. This utility is included in the “Driver & Utility CD” that
came packed with this motherboard.
FAN Fail Alarm Selectable:
This item selects the fan that will be monitored for malfunction.
Shutdown When CPU Fan Fail:
When set to [Enabled], the system will be shut down if the CPU fan is not running.
CPU FanEQ Speed Control:
This item allows you to control the CPU fan speed down to a specific percentage.
When set to a specific percentage, the CPU fan speed will run at the percentage you set in this item if the
temperature limit set in the item “Active Temperature” is not exceeded.
The CPU fan speed will run at 100% regardless of what the percentage you set in this item if the
temperature limit set in the item “Active Temperature” is exceeded.
Active Temperature:
This item sets the temperature limit that would activate the function of “CPU FanEQ Speed Control”
option.
User’s Manual
3-26
Chapter 3
All Voltages, Fans Speed and Thermal Monitoring:
These unchangeable items list the current status of the CPU and environment temperatures, fan speeds,
and system power voltage.
NOTE: The hardware monitoring features for temperatures, fans and voltages will occupy the I/O
address from 294H to 297H. If you have a network adapter, sound card or other add-on cards that might
use those I/O addresses, please adjust your add-on card I/O address to avoid using these addresses.
3-9. Load Fail-Safe Defaults
This option loads the BIOS default values for the most stable, minimal-performance system operations.
3-10. Load Optimized Defaults
This option loads the BIOS default values that are factory settings for optimal-performance system
operations.
3-11. Set Password
This option protects the BIOS configuration or restricts access to the computer itself.
3-12. Save & Exit Setup
This option saves your selections and exits the BIOS setup menu.
3-13. Exit Without Saving
This option exits the BIOS setup menu without saving any change.
KD7A
Install VIA 4-in-1 Driver
A-1
Appendix A. Install VIA 4-in-1 Driver
NOTE: Please install this VIA 4-in-1 driver first after having installed the Windows operating system.
The installation procedures and screen shots in
this section are based on Windows 2000
operating system. For those of other OS, please
follow its on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Driver] tab. Click [VIA 4in1 Driver].
The following screen appears.
3.
Click [Next].
1.
Click [Next].
4.
Click [Next].
2.
Click [Yes].
5.
Click [Next].
User’s Manual
A-2
6.
Appendix A
Click [Next].
7. Choose [Yes, I want to restart my computer
now.], and click [OK] to complete setup.
KD7A
Install Audio Driver
B-1
Appendix B. Install Audio Driver
The installation procedures and screen shots in
this section are based on Windows 2000
operating system. For those of other OS, please
follow its on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Driver] tab. Click [Audio Driver]. The
following screen appears.
1.
Click [Next].
2.
Click [Next].
3.
Click [Yes].
4. Choose [Yes, I want to restart my computer
now.], and click [Finish] to complete setup.
User’s Manual
B-2
KD7A
Appendix B
Install LAN Driver
C-1
Appendix C. Install LAN Driver
The installation procedures and screen shots in
this section are based on Windows 2000
operating system. For those of other OS, please
follow its on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Driver] tab. Click [LAN Driver]. The
following screen appears.
1.
Click [OK] to exit the installation.
User’s Manual
C-2
KD7A
Appendix C
Install VIA USB 2.0 Driver
D-1
Appendix D. Install VIA USB 2.0 Driver
NOTE: There is no need to install VIA USB 2.0 driver for the Windows XP operating system with
Service Pack 1 already installed. Please run the Windows update for the latest Service Pack.
The installation procedures and screen shots in
this section are based on Windows 2000
operating system. For those of other OS, please
follow its on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Driver] tab. Click [VIA USB 2.0
Driver]. The following screen appears.
1.
2.
3.
Click [Next].
4.
Click [Yes].
5.
Click [Yes].
Click [Next].
Click [Yes].
User’s Manual
D-2
Appendix D
6.
Click [Yes].
7.
Click [OK].
8.
Click [Print to File].
9.
Click [OK].
KD7A
BIOS Update Guide
E-1
Appendix E. BIOS Update Guide
The procedure illustrated here is based on the model SE6 as an example; all other models follow the same
process.
1.
First, find out the model name and version number of this motherboard. You can find a bar-code
sticker typed with model name and version number on motherboard PCB.
2.
Find out the current BIOS ID. For example, in this case, the current BIOS ID is [00]. If you already
have the latest BIOS, no any update action is necessary. If your BIOS is not the latest BIOS, go on to
the next step.
3.
Download the correct BIOS file from our Web site.
4.
Double click the downloaded file, it will self-extract
to [awdflash.exe] and [*.bin] files.
5.
Make a bootable floppy disk and copy the necessary
files onto it. You may make a floppy disk bootable
either in Explorer or in the DOS prompt mode.
[c:\]format a: /s
After formatting and transferring the system to the
floppy disk, copy two files into it. One is the BIOS
flash utility [awdflash.exe] and the other is the
decompressed BIOS binary [*.bin] file.
User’s Manual
E-2
Appendix E
6.
Please set the first boot sequence as “Floppy” in BIOS and boot off the floppy disk.
7.
Flash the BIOS in pure DOS mode.
A:\>awdflash se6_sw.bin /cc /cd /cp /py /sn /cks /r_
Note
•
We strongly recommend you use the above parameters following ‘awdflash’ to flash your BIOS.
DO NOT just type “awdflash se6_sw.bin” without the above parameters following the “.bin”
file.
•
The Award flash utility cannot be completed under the Windows environment. It must be done in
a pure DOS environment.
•
You should check which BIOS file is to be used with your motherboard, don’ flash with the
wrong BIOS file. Otherwise, it may cause system malfunctions.
•
Please do not use the Award flash memory writer version earlier than Version 7.52C to flash the
BIOS. Otherwise, it may cause flash fail or un-anticipated problems.
•
During the updating, the progress will be measured by white blocks. The last four blue blocks of
the flash update process represent the “BIOS boot block”. The BIOS boot block is used to prevent
the BIOS from becoming corrupt during programming. It should not be programmed every time.
If this “BIOS boot block” remains intact when the BIOS becomes corrupt during programming,
then you can boot from a bootable floppy next time you boot your computer. This allows you to
flash your BIOS again without the need for technical support from the dealer.
KD7A
Hardware Monitoring (The Winbond Hardware Doctor Utility)
F-1
Appendix F. Hardware Monitoring (The Winbond
Hardware Doctor Utility)
The Winbond Hardware Doctor is a self-diagnostic system for PCs used with Winbond W83627HF
chipset. It protects PC hardware by monitoring several critical items including power supply voltages,
CPU & system fan speeds and CPU and system temperatures. These items are important for the system
operation. Errors may result in permanent damage to the PC. Once any item is out of its normal range, a
warning message pops up reminding you to take proper measures.
The installation procedures and screen shots in
this section are based on Windows 2000
operating system. For those of other OS, please
follow its on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Hardware Doctor] tab. Click
[Hardware Doctor]. The following screen
appears.
1.
2.
3.
Click [Next].
4.
Click [Next].
Click [Next].
Click [Next].
5. Choose [Yes, I want to restart my computer
now.] and click [Finish] to complete setup.
User’s Manual
F-2
Appendix F
Ignore: You can ignore the warning message of
the item, but it will pop up again when an error
of the same item reoccurs.
Disable: The chosen item will be no longer
monitored thereafter, unless you activate it in
the “Configuration” page.
Shutdown: Choosing this button will shutdown
the computer.
Help: You can read more information and
self-diagnose simple problems.
6. Execute the Hardware Doctor by entering
the Windows Menu [Start] [Programs] [Winbond] [Hardware Doctor].
If the warning message pops up due to the
wrong warning limit, you can adjust it in the
“Configuration” option. For example, if you
set the temperature high limit to 40°C, you will
easily exceed the “proper” temperature.
Pay attention to two things when you want to
make any change to the “Configuration” option.
Firstly, you have to make sure your new setting
is in the proper range. Secondly, after you
finished the configuration, you have to save it.
Otherwise, the program will start with the
default value next time.
If you encounter any problem or have any
question about the software settings and
adjustments, please use the Winbond hardware
doctor on-line help. It should give you enough
information to answer your questions.
7. This screen appears. Hardware Doctor
shows you the status of Voltage, Fan Speed, and
Temperature readings as well. If any reading is
critical or over its limitation, the reading turns
red. Also, a pop-up window appears warning
you the system has a problem!
8.
This is the warning message window:
KD7A
Troubleshooting (Need Assistance?)
G-1
Appendix G. Troubleshooting (Need Assistance?)
Q & A:
Q: Do I need to clear the CMOS before I use a new motherboard to assemble my new computer
system?
A: Yes, we highly recommend that you clear the CMOS before installing a new motherboard. Please
move the CMOS jumper from its default 1-2 position to 2-3 for a few seconds, and then back. When
you boot up your system for the first time, follow the instructions in the user's manual to load the
optimized defaults.
Q: If my systems hang when I update the BIOS or set the wrong CPU parameters, what should I
do?
A: Whenever you update the BIOS or if the system hangs due to wrong CPU parameters setting, always
clear CMOS jumper before booting up again.
Q: Why the system failed to boot up and nothing was displayed on the screen after I did some
over-clocking or non-standard settings inside the BIOS? Is the motherboard dead? Do I need to
return it to where I bought from or go through an RMA process?
A: It should not cause hardware or permanent damage to motherboard when BIOS settings were
changed from default to over-clocking or non-standard status.
We suggest the following three troubleshooting methods to discharge CMOS data, recover the
hardware default status, and then make the motherboard working again. No need to bother returning
the motherboard to where you bought from or go through an RMA process.
Step 1. Switch off the power supply unit and then switch it on again after one minute. If there is no
power switch on the power supply unit, disconnect its power cord for one minute and then
connect it back.
Press and hold the <Insert> key on the keyboard, press the power-on button to boot up
system. If it works, loose the <Insert> key and hit <Del> key to enter the BIOS setup page to
do the correct settings.
If the situation remains the same, repeat the procedures in Step 1 for three times, or try Step
2.
Step 2. Switch off the power supply unit or disconnect the power cord. Open the chassis cover.
Locate the CCMOS jumper near the button battery. Change the jumper position from default
1-2 to 2-3 for one minute to discharge the CMOS data, and then put it back to default 1-2
position.
Close the chassis and switch on the power supply unit or plug in the power cord. Press the
power-on button to boot up system. If it works, hit <Del> key to enter the BIOS setup page
to do the correct settings.
If the situation remains the same, try Step 3.
Step 3. The same procedure as Step 2, but in the meantime of discharging the CMOS data, pull out
ATX power connectors from motherboard and remove the button battery during CMOS
discharging.
User’s Manual
G-2
Appendix G
Q: How can I get a quick response to my request for technical support?
A: Be sure to follow the guidelines as stated in the “Technical Support Form” section of this manual.
If you have a problem during operation, in order to help our technical support personnel quickly
determine the problem with your motherboard and give you the answers you need, before filling in
the technical support form, eliminate any peripheral that is not related to the problem, and indicate it
on the form. Fax this form to your dealer or to the company where you bought the hardware in order
to benefit from our technical support. (You can refer to the examples given below)
Example 1:
With a system including: motherboard (with CPU, DRAM, COAST...) HDD, CD-ROM, FDD, VGA
CARD, MPEG CARD, SCSI CARD, SOUND CARD, etc. After the system is assembled, if you
cannot boot up, check the key components of the system using the procedure described below. First
remove all interface cards except the VGA card and try to reboot.
If you still cannot boot up: Try installing another brand/model VGA card and see if the system will
start. If it still does not start, note the VGA card model, motherboard model, Bios identification
number, CPU on the technical support form (refer to main instructions), and describe the problem in
the problem description space provided.
If you can boot up: Insert the interface cards you have removed back into the system, one by one
and try to start the system each time you insert a card, until the system will not start. Keep the VGA
card and the interface card that caused the problem inserted on the motherboard, remove any other
cards or peripheral, and start again. If you still cannot start, note the information related to both cards
in the add-on Card space provided, and don’t forget to indicate the motherboard model, version,
BIOS identification number, CPU (refer to main instructions), and give a description of the problem.
Example 2:
With a system including the motherboard (with CPU, DRAM, COAST...) HDD, CD-ROM, FDD,
VGA CARD, LAN CARD, MPEG CARD, SCSI CARD, SOUND CARD, after assembly and after
having installed the Sound Card Driver, when you restart the system, when it runs the Sound Card
Driver, it resets automatically. This problem may be due to the Sound Card Driver. During the
Starting DOS… procedure, press SHIFT (BY-PASS) key, to skip CONFIG.SYS and
AUTOEXEC.BAT; edit CONFIG.SYS with a text editor, and in function the line that loads the
Sound Card Driver, add a remark REM, in order to disable the Sound Card Driver. See the example
below.
CONFIG.SYS:
DEVICE=C:\DOS\HIMEM.SYS
DEVICE=C:\DOS\EMM386.EXE HIGHSCAN
DOS=HIGH, UMB
FILES=40
BUFFERS=36
REM DEVICEHIGH=C:\PLUGPLAY\DWCFGMG.SYS
LASTDRIVE=Z
Restart the system. If the system starts and does not reset, you can be sure that the problem is due to
the Sound Card Driver. Write down the Sound Card model, motherboard model, BIOS identification
number on the technical support file (refer to main instructions), and describe the problem in the
space provided.
We will show you how to fill the “Technical Support Form”.
KD7A
Troubleshooting (Need Assistance?)
G-3
Main instructions:
To fill in this “Technical Support Form”, refer to the step-by-step instructions given below:
1*. MODEL: Note the model number given in your user’s manual.
Example: KD7A
*
2 . Motherboard model number (REV): Note the motherboard model number labeled on the
motherboard as “REV:*.**”.
Example: REV: 1.01
*
3 . BIOS ID and Part Number: See the on screen message.
4.
DRIVER REV: Note the driver
version number indicated on the
DEVICE DRIVER disk (if any) as
“Release *.**”. For example:
5*. OS/APPLICATION: Indicate the
operating system and applications
you are running on the system.
Example: MS-DOS® 6.22,
Windows® 98 SE, Windows® 2000, etc....
6*. CPU: Indicate the brand and the speed (MHz) of your CPU.
Example:(A) In the “Brand” space, write “Intel”; in the “Specifications” space, write “Pentium® 4
1.9GHz”.
7.
HDD: Indicate the brand and specifications of your HDD(s); specify if the HDD is using IDE1 or
IDE2. If you know the disk capacity, indicate it and check (“”) “ ”; in case you give no
indication, we will consider that your HDD is “IDE1” Master.
Example: In the “HDD” space, check the box; in the Brand space, write “Seagate”; in the
Specifications space, write “ST31621A (1.6GB)”.
8.
CD-ROM Drive: Indicate the brand and specifications of your CD-ROM drive. Specify if it uses IDE1 or IDE2, and check (“”) “ ”; in case you give no indication, we will consider that your
CD-ROM is “IDE2” Master.
Example: In the “CD-ROM drive” space, check the box, in the Brand space, write “Mitsumi”, in the
Specifications space, write “FX-400D”.
9.
System Memory (DDR SDRAM): Indicate the brand and specifications (DDR DIMM) of your
system memory. Such as Density, Description, Module Components, Module Part Number, CAS
Latency, and Speed (MHz).
For example: In the Brand space, write “Micron”; in the Specifications space, write: Density:
128MB, Description: SS 16 Megx72 2.5V ECC Gold, Module Components: (9) 16 Megx 8,
Module Part Number: MT9VDDT1672AG, CAS Latency: 2, Speed (MHz): 200 MHz.
Please give us the detailed information of your DDR SDRAM module; it will help us to simulate the
problems you met.
10. ADD-ON CARD: Indicate which add-on cards you are absolutely sure are related to the problem.
If you cannot identify the problem’s origin, indicate all the add-on cards inserted into your system.
NOTE: Items between the “*” are absolutely necessary.
User’s Manual
G-4
Appendix G
Technical Support Form
Company Name:
Phone Number:
Contact Person:
Fax Number:
E-mail Address:
Model
*
Motherboard Model No.
DRIVER REV
OS/Application
*
Hardware Name
Brand
CPU
HDD
CD-ROM-Drive
System Memory
ADD-ON CARD
Problem Description:
KD7A
*
IDE1
IDE2
IDE1
IDE2
BIOS ID #
Specifications
*
How to Get Technical Support
H-1
Appendix H. How to Get Technical Support
(From our website) http://www.abit.com.tw
(In North America) http://www.abit-usa.com
(In Europe) http://www.abit.nl
Thank you for choosing ABIT products. ABIT sells all our products through distributors,
resellers and system integrators; we have no direct sales to end-users. Before sending email
for tech support please check with your resellers or integrators if you need any services, they
are the ones who sold you your system and they should know best as to what can be done,
how they serve you is a good reference for future purchases.
We appreciate every customer and would like to provide the best service to you. Providing
fast service to our customers is our top priority. However we receive many phone calls and a
huge amount of email from all over the world. At the present time it is impossible for us to
respond to every single inquiry. Therefore it is quite possible that if you send an email to us
that you may not receive a response.
We have done many compatibility tests and reliability tests to make sure our products have
the best quality and compatibility. In case you need service or technical support, please
understand the constraint we have and always check with the reseller who sold the product
to you first.
To expedite service, we recommend that you follow the procedures outlined below before
contacting us. With your help, we can meet our commitment to provide the best service to the
greatest number of ABIT customers:
1. Check the Manual. It sounds simple but we have taken a lot of care in making a
well-written and thorough manual. It is full of information that doesn't only pertain to
motherboards. The CD-ROM included with your board will have the manual as well as
drivers. If you don't have either one, go to our Program Download Area of the Website or
FTP server.
2. Download latest BIOS, software or drivers. Please go to our Program Download area
on our Website to check to see if you have the latest BIOS. They are developed over
periods of time to fixes bugs or incompatibilities. Also please make sure you have the
latest drivers from your peripheral cards makers!
3. Check the ABIT Technical Terms Guide and FAQ on our Website. We are trying to
expand and make the FAQs more helpful and information rich. Let us know if you have
any suggestions. For hot topics check out our HOT FAQ!
User’s Manual
H-2
Appendix H
4. Internet Newsgroups. They are a great source of information and many people there can
offer help. ABIT's Internet News group, alt.comp.periphs.mainboard.abit, is an ideal
forum for the public to exchange information and discuss experiences they have had with
ABIT products. Many times you will see that your question has already been asked before.
This is a public Internet news group and it is reserved for free discussions. Here is a list of
some of the more popular ones:
alt.comp.periphs.mainboard.abit
comp.sys.ibm.pc.hardware.chips
alt.comp.hardware.overclocking
alt.comp.hardware.homebuilt
alt.comp.hardware.pc-homebuilt
5. Ask your reseller. Your ABIT authorized distributor should be able to provide the fastest
solution to your technical problem. We sell our products through distributors who sell to
resellers and stores. Your reseller should be very familiar with your system configuration
and should be able to solve your problem much more efficiently than we could. After all,
your reseller regards you as an important customer who may purchase more products and
who can urge your friends to buy from him or her as well. They integrated and sold the
system to you. They should know best what your system configuration is and your
problem. They should have reasonable return or refund policies. How they serve you is
also a good reference for your next purchase.
6. Contacting ABIT. If you feel that you need to contact ABIT directly you can send email
to the ABIT technical support department. First, please contact the support team for the
branch office closest to you. They will be more familiar with local conditions and
problems and will have better insight as to which resellers offer what products and
services. Due to the huge number of emails coming in every day and other reasons, such
as the time required for problem reproduction, we will not be able to reply to every email.
Please understand that we are selling through distribution channels and don't have the
resources to serve every end-user. However, we will try to do our best to help every
customer. Please also remember that for many of our technical support team English is a
second language, you will have a better chance of getting a helpful answer if your
question can be understood in the first place. Be sure to use very, simple, concise
language that clearly states the problem, avoid rambling or flowery language and always
list your system components. Here is the contact information for our branch offices:
KD7A
How to Get Technical Support
H-3
North America and South America:
Japan:
ABIT Computer (U.S.A.) Corporation
45531 Northport Loop West,
Fremont, California 94538, U.S.A.
Tel: 1-510-623-0500
Fax: 1-510-623-1092
sales@abit-usa.com
technical@abit-usa.com
http://www.abit-usa.com
ABIT Computer (Japan) Co. Ltd.
Fax: 81-3-5396-5110
http://www.abit4u.jp
U.K. and Ireland:
ABIT Computer (U.K.) Corporation
Ltd.
Unit 3, 24-26 Boulton Road,
Stevenage, Herts SG1 4QX, U.K.
Tel: 44-1438-228888
Fax: 44-1438-226333
sales@abitcomputer.co.uk
technical@abitcomputer.co.uk
Germany, Benelux (Belgium,
Netherlands, Luxembourg), Denmark,
Norway, Sweden, Finland, and
Switzerland:
AMOR Computer B.V. (ABIT’s
European Office)
Van Coehoornstraat 7,
5916 PH Venlo, The Netherlands
Tel: 31-77-3204428
Fax: 31-77-3204420
sales@abit.nl
technical@abit.nl
http://www.abit.nl
Austria, Czech, Romania, Bulgaria,
Yugoslavia, Slovakia, Slovenia, Croatia,
Bosnia, Serbia, and Macedonia:
Asguard Computer Ges.m.b.H
Schmalbachstrasse 5,
A-2201 Gerasdorf/Wien, Austria
Tel: 43-1-7346709
Fax: 43-1-7346713
asguard@asguard.at
Shanghai:
ABIT Computer (Shanghai) Co. Ltd.
Tel: 86-21-6235-1829
Fax: 86-21-6235-1832
http://www.abit.com.cn
Russia:
ABIT Computer (Russia) Co. Ltd.
Fax: 7-095-937-2837
techrussia@abit.com.tw
http://www.abit.ru
France, Italy, Spain, Portugal, and
Greece:
ABIT Computer France SARL
Tel: 33-1-5858-0043
Fax: 33-1-5858-0047
http://www.abit.fr
All other territories not covered above
please contact Taiwan Head Office:
When contacting our headquarters please
Note we are located in Taiwan and we are
8+ GMT time. In addition, we have
holidays that may be different from those
in your country.
ABIT Computer Corporation
No.323, Yang Guang St., Neihu, Taipei,
114, Taiwan
Tel: 886-2-8751-8888
Fax: 886-2-8751-3382
sales@abit.com.tw
market@abit.com.tw
technical@abit.com.tw
http://www.abit.com.tw
User’s Manual
H-4
Appendix H
7. RMA Service. If your system has been working but it just stopped, but you have not
installed any new software or hardware recently, it is likely that you have a defective
component. Please contact the reseller from whom you bought the product. You should be
able to get RMA service there.
8. Reporting Compatibility Problems to ABIT. Because of tremendous number of email
messages we receive every day, we are forced to give greater weight to certain types of
messages than to others. For this reason, any compatibility problem that is reported to us,
giving detailed system configuration information and error symptoms will receive the
highest priority. For the other questions, we regret that we may not be able to reply
directly. But your questions may be posted to the Internet news group in order that a
larger number of users can have the benefit of the information. Please check the news
group from time to time.
9. The information listed below are some chipset vendors’ WEB site addresses for your
reference:
HighPoint Technology Inc.’s WEB site: http://www.highpoint-tech.com/
Intel’s WEB site: http://www.intel.com/
Silicon Image’s WEB site: http://www.siimage.com/
SiS’ WEB site: http://www.sis.com.tw/
VIA’s WEB site: http://www.via.com.tw/
Thank You
ABIT Computer Corporation
http://www.abit.com.tw
KD7A