LV-667
Mini-ITX Motherboard
User’s Manual
Edition 1.2
2010/01/07
LV-667 User’s Manual
Copyright
Copyright 2004 - 2005. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to make
improvements to the products.
This document contains proprietary information and protected by copyright. No part of this
document may be reproduced, copied, or translated in any form or any means without prior
written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of their
respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from
the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including without
limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications of
the product described within it at any time without notice and without obligation to notify any
person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at http://www.commell.com.tw
TU
2
UT
LV-667 User’s Manual
Packing List
Please check the package before you starting setup the system
Hardware:
LV-667 series motherboard x 1
Cable Kit:
40-pin ATA100 IDE flat cable x 1
26-pin slim type floppy cable x 1
Serial ATA ribbon cable x 1
I/O Shield x 1
SDTV cable (LV-667T only)
DVI output cable kit (LV-667D only)
Other Accessories:
YPrPb component cable (LV-667T only)
Divers CD (including User’s Manual) x 1
3
LV-667 User’s Manual
Index
Chapter 1 <Introduction> ..................................................................................... 7
1.1 <Product Overview>................................................................................. 7
1.2 <Product Specification> ........................................................................... 8
1.3 <Mechanical Drawing>........................................................................... 11
1.4 <Block Diagram>.................................................................................... 12
Chapter 2 <Hardware Setup>............................................................................. 13
2.1 <Connector Location>............................................................................ 13
2.2 <Jumper Reference> ............................................................................. 14
2.3 <Connector Reference>......................................................................... 15
2.3.1 <Internal Connector>.................................................................. 15
2.3.2 <External Connector>................................................................. 15
2.4 <CPU and Memory Setup> .................................................................... 16
2.4.1< CPU>........................................................................................ 16
2.4.2 <Memory> .................................................................................. 16
2.5 <CMOS Setup> ...................................................................................... 17
2.6 <Enhanced IDE & CF Interface>............................................................ 18
2.7 <Serial ATA Interface>........................................................................... 19
2.8 <Floppy Port>......................................................................................... 20
2.9 <LAN Interface> ..................................................................................... 21
2.10 <Onboard Display Interface> ............................................................... 22
2.10.1 <Analog VGA Interface> .......................................................... 22
2.10.2 <DVI Interface (LV-667D only)> ............................................... 23
2.10.3<TV-out Interface (LV-667T only)>............................................ 24
2.11 <Onboard Audio Interface>.................................................................. 26
2.12 <USB2.0 & IEEE1394 Interface> ......................................................... 28
2.13 <GPIO Interface> ................................................................................. 30
2.14 <Serial Port> ........................................................................................ 31
4
LV-667 User’s Manual
2.15 <Power and Fan Connector> ............................................................... 32
2.15.1 <Power Input> .......................................................................... 32
2.15.2 <Fan Connector>...................................................................... 32
2.16 <Indicator and Switch>......................................................................... 33
Chapter 3 <System Configuration>................................................................... 35
3.1 <SATA RAID Configuration>.................................................................. 35
3.2 <Audio Configuration> ........................................................................... 37
3.3 <Display Configuration>......................................................................... 38
Chapter 4 <BIOS Setup> .................................................................................... 41
Appendix A <I/O Port Pin Assignment> ........................................................... 43
A.1 <IDE Port> ............................................................................................. 43
A.2 <Floppy Port> ........................................................................................ 45
A.3 <IrDA Port> ............................................................................................ 45
A.4 < VGA Port >.......................................................................................... 46
A.5 <Serial ATA Port>................................................................................... 46
A.6 <Serial Port> .......................................................................................... 46
A.8 <LAN Port> ............................................................................................ 47
A.9 <PS/2 Keyboard & Mouse Port>............................................................ 47
Appendix B <Flash BIOS>.................................................................................. 49
B.1
BIOS Auto Flash Tool ...................................................................... 49
B.2
Flash Method................................................................................... 49
Appendix C <System Resources> .................................................................... 51
C.1 <I/O Port Address Map>........................................................................ 51
C.2 <Memory Address Map> ....................................................................... 53
C.3 <System IRQ & DMA Resource> .......................................................... 54
C.3.1 <IRQ> ........................................................................................ 54
C.3.2 <DMA>....................................................................................... 55
Appendix D <Power Consumption Test> ......................................................... 57
Contact Information ............................................................................................ 58
5
LV-667 User’s Manual
(The Page is Left For Blank)
6
LV-667 User’s Manual
Introduction
Chapter 1 <Introduction>
1.1 <Product Overview>
LV-667 is the Mini-ITX motherboard based on VIA chipset. It integrates the last VIA
embedded chipset for CN400 with VT8237, DDR266/333/400 SDRAM, and serial ATA with
RAID to provide the economical embedded platform.
VIA CN400 & VT8237 Chipset
The board comes with the VIA last embedded chipset of CN400, supports DDR266/333/400
SDRAM, integrated the S3 Graphics UniChrome Pro IGP graphics core, hardware MPEG-2
and MPEG-4 acceleration and HDTV interface.
The VT8237 provides the board to support Ultra V-Link (1GB/s) with CN400, two serial ATA
ports with RAID array function, 6 x USB2.0 ports and 5.1 channel AC97 audio.
Multimedia solution
Based on VIA CN400 chipset, the board provides optional 18/24-bit LVDS, HDTV and DVI
interface, which supports dual independent display with CRT. The board also has an
optional mini-AGP interface to work with AGP 8x graphic card.
Onboard AC97 codec provides the high quality of sound including 20-bit, stereo ADC and
6-channel stereo DACs.
Dual LAN Interface
LV-667 also comes with dual 10/100Mbps LAN interface, support boot-on-LAN and
wake-on-LAN function.
High Speed Hot-plug Interface
Based on VIA VT8237, the board provides 6 USB2.0 interfaces with up to 480Mbps of
transferring rate, 3 IEEE1394a interfaces with up to 400Mbps of transferring rate.
Expanded UCR for remote Operating SETUP Bios Feature
Expanded Universal Console Redirection (UCR) is a feature for monitoring POST
messages and running Setup and an operation system from a remote serial terminal.
Product Overview
7
LV-667 User’s Manual
Introduction
1.2 <Product Specification>
General Specification
Form Factor
CPU
Memory
Chipset
BIOS
Green Function
Watchdog Timer
Real Time Clock
Enhanced IDE
Serial ATA
Mini-ITX motherboard
Embedded VIA C3/Eden processor
Ratio: 1.0GHz/800MHz
L1/L2 Cache: 128/64KB
Front side bus: 133MHz
Fanless with Eden 800MHz processor
Optional up to 1.2GHz with 200MHz FSB
1 x 184-pin DDR 266/333/400 SDRAM up to 1GB
Unbufferred, none-ECC memory supported only
VIA CN400 and VT8237
Phoenix-Award v6.00PG 4Mb PnP flash BIOS
Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
System reset programmable watchdog timer with 1 ~ 255
sec./min. of timeout value
VIA VT8237 built-in RTC with lithium battery
Enhanced IDE interface supports dual channels and up to 4
ATAPI devices at Ultra DMA133
One 40-pin and one 44-pin IDE port onboard
VIA VT8237 integrates 2 Serial ATA interface
RAID 0, 1 array Technology supported
Multi-I/O Port
Chipset
Serial Port
USB Port
Parallel Port
Floppy Port
IrDA Port
K/B & Mouse
GPIO
Hardware
Monitor
VIA VT8237 with Winbond W83697UF controller
Two external & two internal RS-232 serial ports
Six Hi-Speed USB 2.0 ports with 480Mbps of transfer rate
None
One slim type Floppy port
One IrDA compliant Infrared interface supports SIR
External PS/2 keyboard and mouse ports on rear I/O panel
One 12-pin Digital I/O connector with 8-bit programmable I/O
interface
Fan speed, CPU temperature and voltage monitoring
VGA Display Interface
Chipset
Core Frequency
Memory
Display Type
Connector
8
VIA CN400 built-in S3 Graphics UniChrome Pro IGP graphics core
200MHz
BIOS selectable 16/32/64MB shard with system memory
CRT, LCD monitor with analog display
External DB15 female connector on rear I/O panel
Product Specification
LV-667 User’s Manual
Introduction
Optional SDTV/HDTV Interface
Codec
TV system
Output Interface
Output Format
VIA VT1625
NTSC (M and J) or PAL (B, D, G, H, I, M, N and Nc) TV system
Composite, S-Video, Component (YPbPr) and D terminal
SDTV output mode for 525p or 625p
HDTV support for 1080i (D3) and 720p (D4)
NTSC - 525i(480i) , 525p(480p) , PAL - 625i(576i) , 625p(576p) ,
HDTV - 1080i , 720p
Resolution
Optional DVI Interface
Codec
Standard
Input Clock
Resolution
Output Interface
VIA VT1632
Compliant with DVI 1.0
25 ~ 165MHz
Up to 1600 x 1200
DVI-D
Ethernet Interface
Chipset
Type
Connector
VIA VT6103 PHY & REALTEK 8100B
10Base-T / 100Base-TX
auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Dual External RJ45 connectors with LED on rear I/O panel
Audio Interface
Chipset
Interface
Connector
VIA VT1616
5.1 channel 3D audio with Line-in, Line-out and MIC-in
External Audio phone jack for Line-out/Front, Line-in/Rear and
MIC(stereo)-in/Center
Onboard audio connector with pin header
Onboard CD-IN connector
Onboard 5-pin S/PDIF interface (optional output kit required)
Expansive Interface
Mini-AGP
PCI
IEEE1394
1 x AGP 8x interface supported (Optional)
1 x PCI slot supports up to two PCI devices through riser card
VIA VT6306 controller integrated
IEEE1394a supported
Up to 400Mb/s of transferring rate
Power and Environment
Power
Requirement
Dimension
Temperature
Standard ATX 20-pin power supply
170 (L) x 170 (H) mm
Operating within 0 ~ 60oC (32 ~ 140oF)
Storage within -20 ~ 85oC (-4 ~ 185oF)
Product Specification
P
P
P
P
P
P
P
P
9
LV-667 User’s Manual
Introduction
Software support
Operation
System
Windows 98SE/ME, Windows 2000, Windows XP
Windows CE 4.0 or later, Windows XP Embedded
Linux (Fedora Core 1, Mandrake 9.2 and Red Hat 9.0)
Ordering Code
LV-667
VIA CN400 with Embedded C3 1.0GHz, VGA, SATA, 5.1CH
Audio, CF, PCI, 4 x RS232, Dual LAN, Mini-AGP
LV-667D
VIA CN400 with Embedded C3 1.0GHz, VGA, SATA, 5.1CH
Audio, CF, PCI, 4 x RS232, Dual LAN, DVI
LV-667T
VIA CN400 with Embedded C3 1.0GHz, VGA, SATA, 5.1CH
Audio, CF, PCI, 4 x RS232, Dual LAN, HDTV
LV-667E8
VIA CN400 with Embedded Eden ESP8000 processor, VGA,
(Fanless)
SATA, 5.1CH Audio, CF, PCI, 4 x RS232, Dual LAN, Mini-AGP
LV-667E8D
VIA CN400 with Embedded Eden ESP8000 processor, VGA,
(Fanless)
SATA, 5.1CH Audio, CF, PCI, 4 x RS232, Dual LAN, DVI
LV-667E8T
VIA CN400 with Embedded Eden ESP8000 processor, VGA,
(Fanless)
SATA, 5.1CH Audio, CF, PCI, 4 x RS232, Dual LAN, HDTV
MA-ATI
AGP 8x graphic card with ATI M10 GPU, 64MB DDR VRAM for
Mini-AGP
MA-1631X
18/24-bit LVDS add-on card for Mini-AGP
1. Please do not order other Mini-AGP modules excluded in the list for this board.
2. The specifications may be different as the actual production.
For further product information please visit the website at http://www.commell.com.tw
TU
10
UT
Product Specification
LV-667 User’s Manual
Introduction
1.3 <Mechanical Drawing>
(Measured by Inches)
(Measured by Mini-meter)
Product Specification
11
LV-667 User’s Manual
Introduction
1.4 <Block Diagram>
Embedded VIA C3 1.0GHz processor
CRT/LCD Monitor
Optional HDTV
Optional DVI
1 x 184-pin
Optional LVDS
DDR266/333/400
Up to 1GB
Optional AGP8x
CN400
Ultra V-Link
1GB/s
6 x USB2.0 Ports
2 x SATA
PCI
VT6103 PHY
VT8237
3 x IEEE1394a
AC97 5.1CH Codec
VT6306
LAN2
8100B
4 x Serial ports
W83782D
BIOS
1 x Floppy ports
8-bit GPIO
Hardware Monitor
IrDA
12
Product Specification
LV-667 User’s Manual
Hardware Setup
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
CN_1394
CN_WOL
CN_AUDIO
CN_VGA CDIN
DIMM
CN_IR
SPDIF
PCI
CN_DVI
ATXPWR
CN_HDTV
CPUFAN
CN_DIO
CN_SDTV
FDD
CN_USB
CN_COM3
MINI_AGP
JFRNT
CN_COM4
IDE1
IDE2
COM2
PS2
VGA
COM1
SPEAKER
Connector Location
CN_SATA1 CN_SATA2 CF
USB_RJ45_2
USB_RJ45_1
LINE_IN
SYSFAN
1394_1
1394_2
MIC_IN
13
LV-667 User’s Manual
Hardware Setup
2.2 <Jumper Reference>
Jumper
JRTC
JDOM
JLAN
JCFSEL
JC1/JC2/JC3/JC4
Function
CMOS Operating/Clear Setting
IDE1 Pin-20 voltage setting
LAN2 Enable/Disable setting
Compact Flash address mode setting
Serial port output voltage setting
JLAN
JRTC
14
JDOM
JCFSEL
JC4/JC3/JC2/JC1
Jumper Reference
LV-667 User’s Manual
Hardware Setup
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector
DIMM
IDE1
IDE2
FDD
CN_SATA1/2
ATXPWR
CN_AUDIO
CDIN
SPDIF
CN_DIO
CN_USB
CN_1394
CPUFAN
SYSFAN
CN_COM3
CN_COM4
CN_IR
CN_WOL
CF
MINI_AGP
CN_DVI
CN_HDTV
CN_SDTV
JFRNT
Function
184-pin DDR SDRAM DIMM
40-pin primary IDE connector
44-pin secondary IDE connector
26-pin slim type floppy connector
7-pin Serial ATA connector
20-pin power supply connector
5 x 2-pin audio connector
4-pin CD-ROM audio input connector
Digital audio optical interface
6 x 2-pin digital I/O connector
5 x 2-pin USB connector
4 x 2-pin IEEE1394 connector
3-pin CPU cooler fan connector
3-pin system cooler fan connector
5 x 2-pin RS232 serial port
5 x 2-pin RS232 serial port
5-pin IrDA connector
3-pin wake on LAN connector
Compact Flash Type II socket
AGP 8x interface
13 x 2-pin DVI interface
5 x 2-pin HDTV interface
4 x 2-pin SDTV interface
14-pin switch/indicator connector
Remark
Standard
Standard
Standard
Standard
Standard
Standard
Standard
LV-667 series
Standard
Standard
Standard
Standard
LV-667 series
Standard
Standard
Standard
Standard
Standard
Standard
LV-667/LV-667E8
LV-667D/LV-667E8D
LV-667T/LV-667E8T
LV-667T/LV-667E8T
Standard
2.3.2 <External Connector>
Connector
VGA
USB_RJ45_1/2
COM1/2
PS2
SPEAKER
LINE_IN
MIC_IN
1394_1/2
Function
DB15 VGA connector
Dual USB and RJ45 LAN connector
Serial port connector
PS/2 Keyboard/Mouse connector
Audio Line-out port
Audio Line-in port
Audio Microphone input port
IEEE1394 port
Connector Reference
Remark
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
15
LV-667 User’s Manual
Hardware Setup
2.4 <CPU and Memory Setup>
2.4.1< CPU>
The board supports Embedded VIA C3/Eden processor, default ratio is C3 1.0GHz with
CPU cooler fan, Eden ESP8000 (800MHz) with heatsink only.
2.4.2 <Memory>
The board supports one 184-pin DDR266/333/400 SDRAM and up to 1GB of capacity, only
non-ECC, unbuffered memory is supported.
DIMM
104-pin
80-pin
Please check the pin number to match the socket side well
before installing memory module.
16
CPU and Memory Setup
LV-667 User’s Manual
Hardware Setup
2.5 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC
1-2
2-3
Mode
Clear CMOS
Normal Operation
Default setting
JRTC
1
CMOS Setup
3
17
LV-667 User’s Manual
Hardware Setup
2.6 <Enhanced IDE & CF Interface>
The board supports two enhanced IDE interface, dual channel for 4 ATAPI devices with
ATA133. Based on embedded application, the board has one 40-pin IDE connector with
jumper selectable for pin-20 +5V supported, and one 44-pin IDE connector. The jumper
JDOM is two-pin type for pin-20 supplied with +5V to apply the DOM (Disk on Module).
The board also provides a Compact Flash Type II socket with jumper (JCFSEL) selectable
slave/Master mode on secondary IDE channel.
Jumper: JDOM
Type: onboard 3-pin header
JDOM
Mode
ON
IDE1 pin-20 5V power supply enable
OFF
No 5V power supply on IDE1 pin-20
Default setting
Jumper: JCFSEL
Type: onboard 3-pin header
JCFSEL
Mode
1-2
Master
2-3
Slave
Default setting
CF
JCFSEL
3
JDOM
IDE1
40
IDE2
44
1
1
1
18
Enhanced IDE & CF Interface
LV-667 User’s Manual
Hardware Setup
2.7 <Serial ATA Interface>
Based on VIA VT8237 Southbridge, the board supports two Serial ATA interfaces with
RAID 0 and 1 array function. The following is the list of the specification of the Serial ATA.
1.
Complies with Serial ATA Specification Revision 1.0
2.
Dual Channel master mode PCI
3.
On-chip two-channel Serial ATA (S-ATA) PHY for support of up to two S-ATA devices
directly.
4.
S-ATA drive transfer rate is capable of up to 150 MB/s per channel (serial speed of 1.5
Gbit/s).
For more information please visit VIA website (www.via.com.tw)
CN_SATA1
CN_SATA2
Serial ATA Interface
19
LV-667 User’s Manual
Hardware Setup
2.8 <Floppy Port>
The board provides a slim type floppy port; please use the 26-pin ribbon cable in the
package to connect the floppy device.
FDD
Floppy rear side
1.
20
4.
Lift up this plastic bar
5.
Slot the cable in (Blue paste for outside)
6.
Press back the plastic bar
Lift up the brown plastic bar
2.
Slot the cable in (Blue paste for
3.
brown bar side)
Press back the plastic bar
Floppy Port
LV-667 User’s Manual
Hardware Setup
2.9 <LAN Interface>
The board provides two 10/100Mbps LAN interfaces with VIA VT6103 PHY and REALTEK
8100B PCI controller, and compliant with standard IEEE 802.3 Ethernet interface for
100BASE-TX. The jumper of JLAN can let you enable/disable LAN2 with REALTEK 8100B.
The CN_WOL is the interface for your PCI LAN card to wake the system up.
Jumper: JLAN
Type: Onboard 3-pin jumper
JLAN
1-2
2-3
Mode
Enable
Disable
Default setting
Connector: CN_WOL
Type: onboard 3-pin (1 x 3) wafer connector
Pin
1
2
Description
+5V Standby
Ground
3
WOL-Ctrl
CN_WOL
1
3
JLAN
3
1
LAN Interface
21
LV-667 User’s Manual
Hardware Setup
2.10 <Onboard Display Interface>
Based on VIA CN400, the board supports integrated S3 Graphics UniChrome Pro IGP
graphics, with BIOS selectable 16/32/64MB shared with system memory for frame buffer.
2.10.1 <Analog VGA Interface>
The board provides a DB15 VGA connector on the rear I/O panel, and one CN_VGA
connector which enable you to connect the VGA interface with MA-ATI (Mini-AGP graphic
card), thus you can have the same display output while applying a graphic card without
additional output connector on chassis.
Connector: CN_VGA
Type: 16-pin (2 x 8) pin header (pitch = 2.0mm)
Pin
Description
Pin
Description
1
Red
2
Green
3
Blue
4
N/C
5
Ground
6
Ground
7
Ground
8
Ground
9
N/C
10
Ground
11
N/C
12
Data
13
HSYNC
14
VSYNC
15
Clock
16
EXCRT
CN_VGA
16
1
22
Onboard Display Interface
LV-667 User’s Manual
Hardware Setup
2.10.2 <DVI Interface (LV-667D only)>
The board provides optional DVI-D interface with VIA VT1632, compliant with DVI 1.0
standard, and supports dual display (clone or extended desktop) function with CRT.
Connector: CN_DVI
Connector type: 26-pin header connector (pitch = 2.54mm)
Pin Number
1
3
5
7
9
11
13
15
17
19
21
23
25
Assignment
TX1+
Ground
TXC+
Ground
N/C
TX2+
Ground
TX0+
N/C
DDCDATA
GND
N/C
N/C
Pin Number
2
4
6
8
10
12
14
16
18
20
22
24
26
Assignment
TX1Ground
TXCPVDD
N/C
TX2Ground
TX0HPDET
DDCCLK
N/C
N/C
N/C
26
1
CN_DVI
Please use attached cable kit to connect
DVI monitors
Onboard Display Interface
23
LV-667 User’s Manual
Hardware Setup
2.10.3<TV-out Interface (LV-667T only)>
The board provides an HDTV and SDTV interface with VIA VT1625, supports PAL and
NTSC of TV system, and dual display (clone or extended desktop) function with CRT.
Connector: CN_SDTV
Connector type: 8-pin header SDTV connector (pitch = 2.54mm)
Pin Number
1
3
5
7
Assignment
GND
C
GND
CVBS
Pin Number
2
4
6
8
Assignment
Y
GND
GND
GND
Connector: CN_HDTV
Connector type: 10-pin header HDTV connector (pitch = 2.54mm)
Pin Number
1
3
5
7
9
Assignment
GND
DACB2
GND
DACB3
LINE2
Pin Number
2
4
6
8
10
Assignment
DACB1
LINE1
GND
LINE3
+5V
CN HDTV
10
1
8
CN SDTV
1
24
Onboard Display Interface
LV-667 User’s Manual
Hardware Setup
To connect the TV set, please follow the diagram below to setup your system:
YPrPb Component Cable
(For HDTV)
S-Video & Composite Cable
(For SDTV)
Onboard Display Interface
25
LV-667 User’s Manual
Hardware Setup
2.11 <Onboard Audio Interface>
The board provides the onboard AC97 5.1-channel audio interface with VIA VT1616, with
three phone jacks on rear I/O panel for Line-out, Line-in, MIC(stereo)-in as 2-channel sound
system, and Front, Rear, Center as 5.1-channel sound system. It also has one 10-pin
header for additional audio output and 4-pin S/PDIF interface for optical/coaxial output.
CN_AUDIO
10
1
4
1
SPDIF
4
1
CDIN
Line-out
Front
26
Line-in
Rear
MIC-in (system setup with 2-channel)
Center (system setup with 5.1-channel)
Onboard Audio Interface
LV-667 User’s Manual
Connector: CN_AUDIO
Type: 10-pin (2 x 5) header (pitch = 2.00mm)
Pin
Description
Pin
1
Line – Left
2
3
Line – Right
4
5
MIC2
6
7
N/C
8
9
Line Out – Right
10
Hardware Setup
Description
Ground
MIC1
Ground
Line Out – Left
Ground
Connector: CDIN (LV-667E8 series do not have this connector)
Type: 4-pin header (pitch = 2.54mm)
Pin
Description
1
CD – Left
2
Ground
3
Ground
4
CD – Right
Connector: SPDIF
Type: 4-pin header (pitch = 2.54mm)
Pin
Description
1
+5V
2
N/C
3
SPDIFOUT
4
GND
Onboard Audio Interface
27
LV-667 User’s Manual
Hardware Setup
2.12 <USB2.0 & IEEE1394 Interface>
Based on VIA VT8237, the board provides 6 USB2.0 ports, and 3 IEEE1394a with VIA
VT6306. The USB2.0 interface provides up to 480Mbps of transferring rate, the IEEE1394a
provides up to 400Mbps of transferring rate.
Interface
IEEE1394a
USB2.0
Controller
VIA VT6306
VIA VT8237
Transfer Rate
100/200/400Mb/s
Up to 480Mb/s
Output Voltage
12V
500mA
1394_1 1394_2
USB1/2/3/4
8
1
CN_1394
10
1
CN_USB
28
USB2.0 & IEEE1394 Interface
LV-667 User’s Manual
Connector: CN_1394
Type: 8-pin header (pitch = 2.00mm)
Pin
Description
1
CPWR
3
TPB25
TPA27
GND
Hardware Setup
Pin
2
4
6
8
Description
GND
TPB2+
TPA2+
GND
Connector: CN_USB
Type: 10-pin (5 x 2) header for USB5/6 Ports
Pin
Description
Pin
1
VCC
2
3
Data04
5
Data0+
6
7
Ground
8
9
Ground
10
Description
VCC
Data1Data1+
Ground
N/C
PS: The USB2.0 will be only active when you connecting with the USB2.0 devices, if you
insert an USB1.1 device, the port will be changed to USB1.1 protocol automatically. The
transferring rate of USB2.0 as 480Mbps is depending on device capacity, exact transferring
rate may not be up to 480Mbps.
USB2.0 & IEEE1394 Interface
29
LV-667 User’s Manual
Hardware Setup
2.13 <GPIO Interface>
The board provides a programmable 8-bit digital I/O interface; you can use this general
purpose I/O port for system control like POS or KIOSK.
Connector: CN_DIO
Type: onboard 2 x 6-pin header, pitch=2.0mm
Pin
1
3
5
7
9
11
Description
Ground
GP0
GP1
GP2
GP3
VCC
Pin
2
4
6
8
10
12
Description
Ground
GP4
GP5
GP6
GP7
+12V
CN_DIO
12
1
30
GPIO Interface
LV-667 User’s Manual
Hardware Setup
2.14 <Serial Port>
The board provides four RS232 serial ports, with jumper selectable +5V/+12V output for
COM3 and COM.
Connector: CN_COM3/4
Type: 10-pin (5 x 2) header for COM3/4
Pin
Description
1
DCD/+5
3
SO
5
GND
7
RTS
9
RI/+12V
Pin
2
4
6
8
10
Description
SIN
DTR
DSR
CTS
N/C
Jumper: JC1/3
Type: Onboard 3-pin jumper
JC1/3
Mode
1-2
COM3/4 pin-1 for +5V output
2-3
RIN1
Default setting
Jumper: JC2/4
Type: Onboard 3-pin jumper
JC2/4
Mode
1-2
COM3/4 pin-9 for +12V output
2-3
-XRI
Default setting
JC4/3/2/1
3
1
10
CN_COM3
CN_COM4
Serial Port
1
31
LV-667 User’s Manual
Hardware Setup
2.15 <Power and Fan Connector>
2.15.1 <Power Input>
Connector: ATXPWR
Type: 20-pin ATX power connector
PIN assignment
1
12V
2
5VSB
3
PWOK
4
GND
5
5V
6
GND
7
5V
8
GND
9
3.3V
10
3.3V
11
12
13
14
15
16
17
18
19
20
5V
5V
-5V
GND
GND
GND
PSON
GND
-12
3.3V
2.15.2 <Fan Connector>
Connector: CPUFAN (LV-667E8 series do not have this connector), SYSFAN
Type: 3-pin fan wafer connector
Pin Description
Pin
Description
Pin
Description
1
Ground
2
+12V
3
Fan Control
ATXPWR
1
20
CPUFAN
1 3
SYSFAN
1
3
32
Power and Fan Connector
LV-667 User’s Manual
Hardware Setup
2.16 <Indicator and Switch>
The JFRNT provides front control panel of the board, such as power button, reset and
beeper, etc. Please check well before you connecting the cables on the chassis.
Connector: JFRNT
Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function
Signal
PIN
Signal
VCC
1
2
VCC
Active
3
4
N/C
Reset
5
6
GND
GND
7
8
VCC
N/C
9
10
N/C
Power
PWRBT
11
12
N/C
Button
GND
13
14
SPKIN
IDE LED
Function
Power
LED
Reset
Speaker
JFRNT
14
1
Indicator and Switch
33
LV-667 User’s Manual
(This Page is Left For Blank)
34
LV-667 User’s Manual
System Configuration
Chapter 3 <System Configuration>
3.1 <SATA RAID Configuration>
The board supports two Serial ATA ports onboard, and supports RAID 0, 1 and JBOD disk
array, the RAID 0, 1 and JBOD are specified below:
RAID 0 (Stripping): Two hard drives operating as one drive for optimized data R/W
performance. It needs two unused drives to build this operation.
RAID 1 (Mirroring): Copies the data from first drive to second drive for data security, and if
one drive fails, the system would access the applications to the workable drive. It needs two
unused drives or one used and one unused drive to build this operation. The second drive
must be the same or lager size than first one.
JBOD (Span): As different as RAID 0, the JBOD combines two disks as one without any
fault tolerance and I/O performance enhancement.
To build Serial ATA disk array, please press <TAB> while booting up the system before
entering OS, and follow the instructions to edit the RAID function.
(Selectable Functions)
(Option Instruction)
(Disk Statement)
SATA RAID Configuration
35
LV-667 User’s Manual
System Configuration
You also can edit disk array under OS, please install the VIA RAID Utility in the driver CD.
(To getting start, please click here to learn more information)
(Click here to build RAID 0)
(Click here to build RAID JBOD)
(Click here to build RAID 0)
36
SATA RAID Configuration
LV-667 User’s Manual
System Configuration
3.2 <Audio Configuration>
The board provides 5.1 channel audio interface with driver installed, please install the VIA
audio driver in the CD before getting start to enjoy the 5.1 channel sound system.
(To enable 5.1-channel sound mode)
Enable S/PDIF
output, required
optional S/PDIF cable
kit for this function
Audio Configuration
37
LV-667 User’s Manual
System Configuration
3.3 <Display Configuration>
The board provides onboard analog VGA interface, and optional digital display interface
with HDTV, LVDS and DVI, please install the VIA video driver before enjoy the vivid display.
Based on the VIA CN400 with S3 UniChrome Pro graphic, the board provides dual display
function for clone or extended desktop modes with secondary display device attached.
After installing video driver, please launch the desktop display properties.
Please select each device to
configure the resolution and
color bit.
For secondary display device, you have two options selectable.
For more display properties setting, please click “Advanced” button.
38
Display Configuration
LV-667 User’s Manual
System Configuration
Please select S3Display for advanced device setting.
Connected Devices
Click check box to
enable/disable device
Specified display setup
When you set dual display clone mode, you’ll see the same screen display on two devices.
When you set the dual display for extended desktop mode, you can have the independent
desktop on the second device.
Display Configuration
39
LV-667 User’s Manual
(This Page is Left for Blank)
40
LV-667 User’s Manual
BIOS Setup
Chapter 4 <BIOS Setup>
The motherboard uses the Award BIOS for the system configuration. The Award
BIOS in the single board computer is a customized version of the industrial standard
BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU
architecture based processors and computers. The BIOS provides critical low-level
support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the
basic configuration setting. The settings are stored in a dedicated battery-backed
memory, NVRAM, retains the information when the power is turned off. If the battery
runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided here
for reference purpose only. The settings and configurations of the BIOS are current at
the time of print, and therefore they may not be exactly the same as that displayed on
your screen.
To activate CMOS Setup program, press <DEL> key immediately after you turn on
the system. The following message “Press DEL to enter SETUP” should appear in the
lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main
Menu will be displayed as Figure 4-1. You can use arrow keys to select your function,
press <Enter> key to accept the selection and enter the sub-menu.
Figure 4-1 CMOS Setup Utility Main Screen
BIOS Setup
41
LV-667 User’s Manual
(This Page is Left for Blank)
42
LV-667 User’s Manual
I/O Port Pin Assignment
Appendix A <I/O Port Pin Assignment>
A.1 <IDE Port>
Connector: IDE1
Type: 40-pin (20 x 2) box header
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
IDE Port
Description
Reset
D7
D6
D5
D4
D3
D2
D1
D0
Ground
REQ
IOW-/STOP
IOR-/HDMARDY
IORDY/DDMARDY
DACKIRQ
A1
A0
CS0 (MASTER CS)
LED ACT-
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
39
1
40
2
Description
Ground
D8
D9
D10
D11
D12
D13
D14
D15
VCC
Ground
Ground
Ground
IDESEL
Ground
N/C
CBLID
A2
CS1 (SLAVE CS)
Ground
43
LV-667 User’s Manual
Connector: IDE2
2
44
1
43
Type: 44-pin (22 x 2) box header
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
44
Description
Reset
D7
D6
D5
D4
D3
D2
D1
D0
Ground
REQ
IOW-/STOP
IOR-/HDMARDY
IORDY/DDMARDY
DACKIRQ
A1
A0
CS1
ASP1
Vcc
Ground
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
Description
Ground
D8
D9
D10
D11
D12
D13
D14
D15
N/C
Ground
Ground
Ground
Ground
Ground
N/C
SD
A2
CS3
Ground
Vcc
Ground
IDE Port
LV-667 User’s Manual
I/O Port Pin Assignment
A.2 <Floppy Port>
Connector: FDD
Type: 26-pin connector
Pin
Description
1
VCC
3
VCC
5
VCC
7
DRV1
9
MTR1
11
RPM
13
N/C
15
Ground
17
Ground
19
N/C
21
N/C
23
Ground
25
Ground
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
Description
INDEX
DRV0
DSKCHG
N/C
MTR0
DIR
STEP
WRITE DATA
WRITE GATE
TRACK 0
WRPTR
RDATASEL
A.3 <IrDA Port>
Connector: CN_IR
Type: 5-pin header for SIR Ports
Pin
Description
1
Vcc
2
N/C
3
IRRX
4
Ground
5
IRTX
Floppy Port
5
1
45
LV-667 User’s Manual
6
A.4 < VGA Port >
Connector: VGA
Type: 15-pin D-sub female connector on bracket
Pin
Description
Pin
Description
1
RED
6
Ground
2
GREEN
7
Ground
3
BLUE
8
Ground
4
N/C
9
LVGA5V
5
Ground
10
Ground
A.5 <Serial ATA Port>
1
1
2
3
4
5
11
12
13
14
15
10
Pin
11
12
13
14
15
Description
N/C
5VCDA
HSYNC
VSYNC
5VCLK
7
Connector: CN_SATA1/2
Type: 7-pin wafer connector
1
2
3
4
5
6
7
GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXN1 RSATA_RXP1 GND
A.6 <Serial Port>
Connector: COM1/2
Type: 9-pin D-sub male connector on bracket
Pin
Description
Pin
1
DCD
6
2
SIN
7
3
SO
8
4
DTR
9
5
Ground
46
1
2
3
4
5
6
7
8
9
Description
DSR
RTS
CTS
RI
VGA Port
LV-667 User’s Manual
I/O Port Pin Assignment
A.8 <LAN Port>
1
Connector: RJ45_1/2
Type: RJ45 connector with LED on bracket
Pin
Description
1
TX+
2
TX-
3
RX+
4
N/C
8
5
N/C
6
RX-
7
N/C
8
N/C
A.9 <PS/2 Keyboard & Mouse Port>
1
Connector: Keyboard
Type: 6-pin Mini-DIN connector on bracket
Pin
Description
1
N/C
2
KB_CK
3
BVCC
4
5
4
IOGND
6
5
N/C
6
KB_DT
1
Connector: Mouse
Type: 6-pin Mini-DIN connector on bracket
LAN Port
1
N/C
2
MS_CK
3
BVCC
2
3
4
5
Pin
Description
2
3
4
IOGND
5
N/C
6
6
MS_DT
47
LV-667 User’s Manual
(This Page is Left for Blank)
48
LV-667 User’s Manual
I/O Port Pin Assignment
Appendix B <Flash BIOS>
B.1 BIOS Auto Flash Tool
The board is based on Award BIOS and can be updated easily by the BIOS auto flash
tool. You can download the tool online at the address below:
http://www.award.com
http://www.commell.com.tw/support/support.htm
TU
UT
TU
UT
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS
flash ship and update the BIOS.
B.2 Flash Method
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the
web-site at below:
http://www.commell.com.tw/support/support.htm
LAN Port
49
LV-667 User’s Manual
(This Page is Left for Blank)
50
LV-667 User’s Manual
System Resources
Appendix C <System Resources>
C.1 <I/O Port Address Map>
Address Range
Devices
x0000 - x000F
Direct memory access controller
x0010 - x001F
Motherboard resources
x0020 - x0021
Programmable interrupt controller
x0022 - x003F
Motherboard resources
x0040 - x0043
System timer
x0044 - x005F
Motherboard resources
x0060 - x0060
Standard 101/102-Key or Microsoft Natural Keyboard
x0061 - x0061
System speaker
x0062 - x0063
Motherboard resources
x0064 - x0064
Standard 101/102-Key or Microsoft Natural Keyboard
x0065 - x006F
Motherboard resources
x0070 - x0073
System CMOS/real time clock
x0074 - x007F
Motherboard resources
x0080 - x0090
Direct memory access controller
x0091 - x0093
Motherboard resources
x0094 - x009F
Direct memory access controller
x00A0 - x00A1
Programmable interrupt controller
x00A2 - x00BF
Motherboard resources
x00C0 - x00DF
Direct memory access controller
x00E0 - x00EF
Motherboard resources
x00F0 - x00FF
Numeric data processor
x0170 - x0177
VIA Bus Master PCI IDE Controller
x0170 - x0177
Secondary IDE controller (dual fifo)
x01F0 - x01F7
VIA Bus Master PCI IDE Controller
x01F0 - x01F7
Primary IDE controller (dual fifo)
x0200 - x0200
Gameport Joystick
x0201 - x0207
Gameport Joystick
x0294 - x0297
Motherboard resources
x02E8 - x02EF
Communications Port (COM4)
x02F8 - x02FF
Communications Port (COM2)
x0330 - x0331
MPU-401 Compatible
x0376 - x0376
VIA Bus Master PCI IDE Controller
x0376 - x0376
Secondary IDE controller (dual fifo)
x03B0 - x03BB
VIA/S3G UniChrome Pro IGP
x03C0 - x03DF
VIA/S3G UniChrome Pro IGP
x03E8 - x03EF
Communications Port (COM3)
x03F2 - x03F5
Standard Floppy Disk Controller
x03F6 - x03F6
VIA Bus Master PCI IDE Controller
I/O Port Address Map
51
LV-667 User’s Manual
Address Range
Devices
System Resources
x03F6 - x03F6
Primary IDE controller (dual fifo)
x03F7 - x03F7
Standard Floppy Disk Controller
x03F8 - x03FF
Communications Port (COM1)
x0400 - x047F
Motherboard resources
x04D0 - x04D1
Motherboard resources
x0500 - x050F
Motherboard resources
x0CF8 - x0CFF
PCI bus
xD000 - xD0FF
Realtek RTL8139/810x Family Fast Ethernet NIC
xD400 - xD4FF
VIA SATA RAID Controller
xD800 - xD8FF
Vinyl AC'97 Codec Combo Driver (WDM)
xDC00 - xDCFF
VIA Rhine II Fast Ethernet Adapter
xE000 - xE007
VIA SATA RAID Controller
xE100 - xE103
VIA SATA RAID Controller
xE200 - xE20F
VIA SATA RAID Controller
xE300 - xE37F
PCI OHCI Compliant IEEE 1394 Host Controller
xE400 - xE407
Primary IDE controller (dual fifo)
xE400 - xE40F
VIA Bus Master PCI IDE Controller
xE408 - xE40F
Secondary IDE controller (dual fifo)
xE500 - xE51F
VIA Tech 3038 PCI to USB Universal Host Controller
xE600 - xE61F
VIA Tech 3038 PCI to USB Universal Host Controller
xE700 - xE71F
VIA Tech 3038 PCI to USB Universal Host Controller
xE800 - xE81F
VIA Tech 3038 PCI to USB Universal Host Controller
xE900 - xE907
VIA SATA RAID Controller
xEA00 - xEA03
VIA SATA RAID Controller
52
I/O Port Address Map
LV-667 User’s Manual
System Resources
C.2 <Memory Address Map>
Range
Devices
x00000000 - x0009FFFF
System board extension for ACPI BIOS
x000A0000 - x000AFFFF
VIA/S3G UniChrome Pro IGP
x000B0000 - x000BFFFF
VIA/S3G UniChrome Pro IGP
x000C0000 - x000CEFFF
VIA/S3G UniChrome Pro IGP
x000CF000 - x000CFFFF
System board extension for ACPI BIOS
x000F0000 - x000F7FFF
System board extension for ACPI BIOS
x000F8000 - x000FBFFF
System board extension for ACPI BIOS
x000FC000 - x000FFFFF
System board extension for ACPI BIOS
x00100000 - x1BDEFFFF
System board extension for ACPI BIOS
x1BDF0000 - x1BDFFFFF
System board extension for ACPI BIOS
xE8000000 - xEFFFFFFF
VIA Standard Host Bridge
xF0000000 - xF3FFFFFF
VIA CPU to AGP2.0/AGP3.0 Controller
xF0000000 - xF3FFFFFF
VIA/S3G UniChrome Pro IGP
xF4000000 - xF4FFFFFF
VIA/S3G UniChrome Pro IGP
xF4000000 - xF5FFFFFF
VIA CPU to AGP2.0/AGP3.0 Controller
xF5000000 - xF500FFFF
VIA/S3G UniChrome Pro IGP
xF6000000 - xF60000FF
Realtek RTL8139/810x Family Fast Ethernet NIC
xF6001000 - xF60017FF
PCI OHCI Compliant IEEE 1394 Host Controller
xF6002000 - xF60020FF
VIA PCI to USB Enhanced Host Controller
xF6003000 - xF60030FF
VIA Rhine II Fast Ethernet Adapter
xFEC00000 - xFEC00FFF
System board extension for ACPI BIOS
xFEE00000 - xFEE00FFF
System board extension for ACPI BIOS
xFFF80000 - xFFFEFFFF
System board extension for ACPI BIOS
xFFFF0000 - xFFFFFFFF
System board extension for ACPI BIOS
Memory Address Map
53
LV-667 User’s Manual
System Resources
C.3 <System IRQ & DMA Resource>
C.3.1 <IRQ>
IRQ Number
Devices
0
System timer
1
Standard 101/102-Key or Microsoft Natural Keyboard
2
Programmable interrupt controller
3
Communications Port (COM2)
4
Communications Port (COM4)
4
Communications Port (COM3)
4
Communications Port (COM1)
5
VIA Rhine II Fast Ethernet Adapter
5
VIA Tech 3038 PCI to USB Universal Host Controller
5
VIA Tech 3038 PCI to USB Universal Host Controller
5
VIA/S3G UniChrome Pro IGP
5
ACPI IRQ Holder for PCI IRQ Steering
6
Standard Floppy Disk Controller
7
Vinyl AC'97 Codec Combo Driver (WDM)
7
VIA PCI to USB Enhanced Host Controller
7
Realtek RTL8139/810x Family Fast Ethernet NIC
7
ACPI IRQ Holder for PCI IRQ Steering
8
System CMOS/real time clock
9
SCI IRQ used by ACPI bus
10
MPU-401 Compatible
11
VIA Tech 3038 PCI to USB Universal Host Controller
11
VIA Tech 3038 PCI to USB Universal Host Controller
11
VIA SATA RAID Controller
11
PCI OHCI Compliant IEEE 1394 Host Controller
11
ACPI IRQ Holder for PCI IRQ Steering
11
ACPI IRQ Holder for PCI IRQ Steering
54
IRQ & DMA Resource
LV-667 User’s Manual
IRQ Number
Devices
12
PS/2 Compatible Mouse Port
13
Numeric data processor
14
Primary IDE controller (dual fifo)
14
VIA Bus Master PCI IDE Controller
15
Secondary IDE controller (dual fifo)
15
VIA Bus Master PCI IDE Controller
System Resources
C.3.2 <DMA>
Channel
Device
2
Standard Floppy Disk Controller
4
Direct memory access controller
0
(free)
1
(free)
3
(free)
5
(free)
6
(free)
7
(free)
IRQ & DMA Resource
55
LV-667 User’s Manual
(This Page is Left for Blank)
56
LV-667 User’s Manual
Power Consumption Test
Appendix D <Power Consumption Test>
Hardware
CPU
Memory
HDD
CDROM
Power Supply
Embedded VIA C3 1.0GHz
HYNIX DDR400 1GB
Seagate ST340014A
SONY DDU1621 DVD-ROM
AOPEN FSP300-60ATV
(not counted)
(not counted)
Software
OS
Application
Windows XP SP1 English Version
3DMARK 2001
Test Result
3.3V
5V
12V
0.3A
3.5A
0.2A
0.99W
17.5W
2.4W
Embedded VIA C3 1.0GHz
HYNIX DDR400 1GB
Seagate ST340014A
SONY DDU1621 DVD-ROM
AOPEN FSP300-60ATV
MA-ATI
(not counted)
(not counted)
Hardware
CPU
Memory
HDD
CDROM
Power Supply
Mini-AGP
Software
OS
Application
Windows XP SP1 English Version
3DMARK 2003
Test Result
3.3V
5V
12V
Power Consumption Test
1.2A
4.3A
0.3A
3.96W
21.5W
3.6W
57
LV-667 User’s Manual
Contact Information
Any advice or comment about our products and service, or anything
we can help you please don’t hesitate to contact with us. We will do
our best to support you for your pr
Taiwan Commate Computer Inc.
Address
8F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih
Taipei Hsien, Taiwan
TEL
+886-2-26963909
FAX
+886-2-26963911
Website
http://www.commell.com.tw
TU
UT
info@commell.com.tw (General Information)
E-Mail
TU
UT
tech@commell.com.tw (Technical Support)
TU
UT
Commell is our trademark of industrial PC division
58