Siemens SCD 1297 Operating instructions

High Resolution 31 cm/12" LCD-Monitor SCD 1297
Operating Instructions
SCD 1297-C/CT (1) (Chassis)
6GF6240-3MA (-3MB with Touch)
SCD 1297-E/ET/ETH/ETC/ETB (1) (Mountable)
6GF6240-4MA (-4MB with Touch)
6GF6244-4MB/ 6GF6240-4MC/6GF6242-4MB
SCD 1297-R/RT (1)(Rack 19")
6AV8100-0CA00.0AA1/6AV8100-0CB00-0AA1)
6GF6240-6MA01 (-6MB01 with Touch)
 Copyright Siemens AG
LCD-Monitor SCD1297
Page 1 / 19
DOC-No.: B3 0071D1.DOC
No part of this document may be
reproduced or transmitted without express
permission.
Violations will result in prosecution. All
rights reserved.
2001 All rights reserved
이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기 바라며 가정 외의 지역에서 사용하는 것을 목적으로 합니다.
LCD-Monitor SCD1297
Page 2 / 19
DOC-No.: B3 0071D1.DOC
Contents
1
Overview ..................................................................................................................................... 4
1.1
Layout of this Handbook ...................................................................................................... 5
1.2
Warnings and Safety Notes ................................................................................................. 6
1.2.1
Instructions for Handling Assemblies Susceptible to Electrostatic Shock ..................... 7
2
General Installation ..................................................................................................................... 7
2.1
Removing the Packaging and Checking Individual Parts ..................................................... 7
2.2
Installing the LCD-Monitor ................................................................................................... 8
2.2.1
Installation of the AC/DC-power supply unit or 24V-DC/DC-Converter....................... 10
2.3
Cable Connections and Pin Assignments .......................................................................... 10
2.4
Electrical Installation .......................................................................................................... 12
2.5
Touch-screen version SCD 1297xx/T ................................................................................ 12
3
Operation and Alignment........................................................................................................... 13
3.1
Location of the Operation and Alignment Controls............................................................. 13
3.2
Using and Adjusting the Converter .................................................................................... 14
3.2.1
OSD-Menu................................................................................................................. 14
3.2.2.
Quick-OSD-Menu-Functions ...................................................................................... 15
3.2.3.
OSD-Menu-Function .................................................................................................. 16
4
Technical Data .......................................................................................................................... 18
4.1
Display Module .................................................................................................................. 18
4.2
Power Supply .................................................................................................................... 18
4.3
Operating Conditions ......................................................................................................... 18
4.4
Protection .......................................................................................................................... 18
4.5
Enclosure .......................................................................................................................... 19
4.6
Input Signals...................................................................................................................... 19
4.7
EU Declaration of Conformity on EMC............................................................................... 19
Figures
Figure 1: Dimensions of the SCD 1297-C/CT...................................................................................... 8
Figure 2: Dimensions of the SCD 1297-E/ET ...................................................................................... 9
Figure 3: Dimensions of the SCD 1297-R/RT...................................................................................... 9
Figure 4: VGA Interface..................................................................................................................... 11
Figure 5: Location of the operation and alignment controls ............................................................... 13
LCD-Monitor SCD1297
Page 3 / 19
DOC-No.: B3 0071D1.DOC
1 Overview
The LCD monitor SCD 1297 has been developed and constructed especially for industrial
applications. This monitor can be used in applications where a standard CRT-device would be
unsuitable, due to space or environmental restrictions. Its compact enclosure opens up a wide
spectrum of possible application areas for the SCD 1297, ranging from air-conditioned computer
rooms behind a switching cabinet door, to the immediate vicinity of machinery in a special protective
enclosure. As is the case for all industrial systems, the monitor has been designed to withstand the
particular demands placed upon such equipment, e.g., it is immune to electromagnetic radiation and
can withstand a large temperature range.
The trend-setting LCD technology in this monitor has relegated picture geometry distortion and colour
patches to the past. Even at the low refresh rate of 50 Hz. the screen remains flicker-free. The SCD
1297 thus fulfils even the strictest ergonomic requirements. Pictures of lower resolution are expanded
to fill the screen.
The SCD 1297 can simultaneously display up to 262144 colours enabling realistic colour images and
videos to be displayed. The LCD-monitor contains special hardware to convert a standard analogue
VGA video signal for the display controller. Compatibility with conventional CRT monitors is, thus,
guaranteed.
It is very easy to adjust the monitor settings using the clearly designed OSD (On Screen Display). The
“Automatic Alignment” function does away with the need to carry out tedious adjustments such as
picture position and phase. At the press of a button, the monitor performs these alignments
automatically.
The SCD 1297 is equipped with an active 12.1” TFT display module with a maximum resolution of
800x600 pixels. The integrated power management system VESA DPMS, allows a significant
reduction in power consumption when the synchronisation signal from the computer has been
switched off, compared with that under “normal” operation.
Three versions of the monitor are available:
stand-alone chassis
mountable with front plate
19“ rack 6 HE
LCD-Monitor SCD1297
SCD1297-C(CT with Touch)
SCD1297-E (ET with Touch)
SCD1297-R(RT with Touch)
Page 4 / 19
DOC-No.: B3 0071D1.DOC
1.1 Layout of this Handbook
This handbook should be kept within reach while installing and operating the LCD-monitor. It has
been laid out so that even inexperienced users can find the information they require. Chapters are
clearly arranged according to subject.
In detail, the chapters are arranged as follows:
• Chapter 1
Introduction
This chapter provides a brief description of the SCD 1297, including its
properties, application areas and special features.
• Chapter 2
Installation
This chapter is mainly concerned with preparing the LCD-monitor for
use, its installation and cabling.
• Chapter 3
Operation
All operations and adjustment possibilities for the SCD 1297 are
described here
• Chapter 4
Technical Data
This chapter contains technical details such as dimensions, power
supply, environmental considerations and EMC data.
Important:
The manufacturer has gone to great lengths to match the quality of the documentation
to the high standard of this product. In achieving this, we are reliant on the support of our customers.
If anything in this handbook is not clearly understandable or if there are any errors, then please
submit a short note to that effect. The same applies for any suggestions for improvement. We are
grateful for all such assistance.
LCD-Monitor SCD1297
Page 5 / 19
DOC-No.: B3 0071D1.DOC
1.2 Warnings and Safety Notes
Transport
The LCD-monitor should only be transported in its original packaging to ensure it will be protected
against shocks and rough handling.
Setting up
When installing the monitor, it should be noted whether any moisture (condensation) has entered the
unit during transport or storage. Additional important installation information can be found in the
“Technical Data” chapter.
EMC
This is a Class A piece of equipment (industrial use). In domestic situations, it may cause
interference. Under such circumstances, the operator can be required to undertake appropriate
measures to minimise problems
.
This LCD-monitor is a component designed for building into industrial systems. The operator of the
entire plant is responsible for maintaining electromagnetic compatibility according to EMC-law.
Repairs
Before the unit is opened, the supply voltage must be switched off. Only authorised persons may
open the unit.
Additions or changes to the unit may damage the system or affect its EMC behaviour.
Cleaning
The unit must be isolated from the power supply before cleaning. If heavily soiled, the LCD-monitor
can be cleaned with a damp cloth and mild detergent. Care must be taken to ensure that no moisture
enters the unit during cleaning.
Scouring powders and solvents must never be allowed to come in contact with the unit. The inside of
the unit is to be cleaned by qualified service technicians only.
LCD-Monitor SCD1297
Page 6 / 19
DOC-No.: B3 0071D1.DOC
1.2.1 Instructions for Handling
Electrostatic Shock
Assemblies
Susceptible
to
Most of the assemblies within the SCD 1297 LCD-monitor contain components which can be
destroyed by electrostatic voltages. It is also possible for the assemblies to be damaged in such a
way that total failure does not occur.
If you (as an authorised service technician) are handling such assemblies then the following
precautions should be observed:
When such assemblies are being handled, a means of electrostatic discharge must be available. This
can be, for example, an earthed object, which can be touched to discharge electrostatic voltages.
This applies to all tools used (insulated). They must also be discharged at an earthed object.
When assemblies are removed or added to the system, the unit must always be switched off and the
power supply cable disconnected.
Vulnerable assemblies should always be held by their edge. Avoid touching tracks and contact pins.
2 General Installation
Preparation for installing the LCD-monitor include the following points:
Removal of all packaging
Checking of components for damage
Comparison of components received with those on the delivery note
Connection to the computer system and power supply
Building into your system, bearing in mind technical and ergonomic aspects
2.1 Removing the Packaging and Checking Individual Parts
After unpacking all the delivered components, they should be checked for completeness and for
possible transport damage (visual inspection). If any deficiencies are found then please contact the
service department given on the delivery note. Have the delivery note number, serial number and a
description of the deficiency to hand.
The original packaging should be kept for future transportation.
LCD-Monitor SCD1297
Page 7 / 19
DOC-No.: B3 0071D1.DOC
2.2 Installing the LCD-Monitor
Two fixing brackets can be used to mount the SCD 1297-C(CT) behind a front plate.
The SCD 1297-E(ET) is delivered together with a front plate. It has a sealing band all the way round.
When mounting the front plate, care must be taken to ensure that the O-ring remains in its groove
otherwise the seal may not be tight.
The SCD1297-R(RT) is designed for mounting in a standard 19“ rack system. Supporting rails are not
necessary.
329
307
40
5x20
ACTIVE AREA 246x184.5
41
111
147
229
A
76
154.5
Figure 1: Dimensions of the SCD 1297-C/CT
LCD-Monitor SCD1297
319
Page 8 / 19
DOC-No.: B3 0071D1.DOC
40
M3x10
A
76
4
Figure 2: Dimensions of the SCD 1297-E/ET
483
465
40
SIEMENS
A
ACTIVE AREA 246x184.5
+
-
265.9
190.4
ON
76
4
Figure 3: Dimensions of the SCD 1297-R/RT
LCD-Monitor SCD1297
Page 9 / 19
DOC-No.: B3 0071D1.DOC
Thermal Problems
In order that the LCD-monitor maintains an optimum operating temperature while in use, air must be
allowed to circulate freely around the SCD 1297 enclosure. It is particularly important that the rear of
the system is kept free.
Please bear in mind that increased temperatures can lead to defects and to a significant reduction in
the lifetime of the monitor.
EMC Problems
This LCD-monitor is a piece of equipment designed for building into an industrial system. The
operator of the entire plant is responsible for maintaining electromagnetic compatibility according to
EMC laws.
Safety Problems
All voltage and signal connections must adhere to appropriate legal requirements.
Ergonomics
The screen should be easily viewable from all sides and without reflections.
2.2.1 Installation of the AC/DC-power supply unit or 24V-DC/DCConverter
Either an AC/DC power supply unit or a DC/DC converter can be used to supply the control panel with
24DC. If an AC/DC power supply unit is used, it is attached to the enclosure using the bracket
indicated in Fig. 1 on page 10.
If the DC/DC converter, which is delivered with the unit, is to be used then it should be inserted below
the AC/DC power supply unit shown in Fig. 1, so that the 24V connector is accessible. The DC/DC
converter should then be screwed to the enclosure using to the two holes provided for the bracket.
The cable from the AC/DC power
supply unit (12VDC) or from the
DC/DC convertr is plugged directly
into the socket (power) on the SCD
1297-K. It should be secured using
a pul-relief.
Einschieben des DC/DC-Wandlers
unter den Deckel
Befestigungslöcher für DC/DC-Wandler
2.3 Cable Connections and Pin Assignments
The LCD-monitor has been tested and set-up in the factory. Before use, the power supply and the
VGA signals should be connected to the sockets provided. Connections to the monitor should adhere
to EMC regulations.
LCD-Monitor SCD1297
Page 10 / 19
DOC-No.: B3 0071D1.DOC
A high-quality 75-ohm coaxial cable must be used for the VGA-signals. Low quality cables can result
in interference and shadowing on the display.
VGA-Interface
The VGA interface is a standard 15-pin male HD-D-type connector.
Figure 4: VGA Interface
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
Video input RED
Video input GREEN
Video input BLUE
Not used
Not used
GND (RED)
GND (GREEN)
GND (BLUE)
Not used
GND
Not used
Not used
H-Sync.
V-Sync.
Not used
LCD-Monitor SCD1297
Page 11 / 19
DOC-No.: B3 0071D1.DOC
Power Supply
Power is supplied to the SCD 1297 via a standard power connector on the rear of the unit.
Pin
O
Name
GND
+12V
Description
Power supply ground GND
Power supply +12VDC
2.4 Electrical Installation
Before connecting the SCD 1297 to the power supply, a check should be carried out as to whether
the VGA connector is plugged in properly and that the screws are tightened. There is a compartment
on the rear of the unit to hold the standard power supply unit delivered with the display.
The monitor can, however, also be powered by a 12 V supply (observe polarity of the power supply
connections).
If a video signal is connected, the image will appear immediately on the screen.
There are many possible reasons why an image might fail to appear on the display after it has been
switched on:
- no VGA signal connected
- no synchronisation signal connected
-
horizontal and vertical synchronisation signals are connected the wrong way round
2.5 Touch-screen version SCD 1297xx/T
The installation of the necessary touch screen driver software is described in the manufacturers
original touch-screen manual which is enclosed.
LCD-Monitor SCD1297
Page 12 / 19
DOC-No.: B3 0071D1.DOC
3 Operation and Alignment
This chapter contains a description of all the operating and alignment functions.
3.1 Location of the Operation and Alignment Controls
All the controls are accessible from the rear of the unit. Their exact position in shown in Figure 1 on
page 32. These controls are used for navigating in the OSD menu and for selecting and altering
parameters.
S1
S2
S3
S4
Power supply
VGA-interface
Touchscreen (option)
and service connector
Figure 5: Location of the operation and alignment controls
S1
S2
S3
S4
LCD-Monitor SCD1297
+
Menu
Set
Page 13 / 19
DOC-No.: B3 0071D1.DOC
3.2 Using and Adjusting the Converter
Since there are no standards for video output signals from VGA cards, the first time the unit is
switched on it will automatically adjust itself to the graphic card currently being used.
3.2.1 OSD-Menu
The „On Screen Display“ OSD is a menu system, which is shown on the display. With the
help of OSD and the described controls elements, all adjustments of the monitor are
executable. There are just 4 keys S1 to S4 to control the OSD.
OSD-Menu / Quick-OSD-Menu
In addition to the OSD menu there are more possibilities to adjust important functions like
brightness, contrast and automatic adjustment directly via a Quick-OSD-menu.
Function(s) of the control keys:
<+>
Increase value, menu navigation (go to sub menu / go to right)
Invoke Quick-OSD-menu: To execute an automatic adjustment
<->
Decrease value, menu navigation (go to left)
MENU
Invoke OSD
Menu navigation (switching between main- and sub-menu)
SET
Menu navigation (go down)
Invoke Quick-OSD-menu: Brightness and contrast adjustment
LCD-Monitor SCD1297
Page 14 / 19
DOC-No.: B3 0071D1.DOC
3.2.2.
Quick-OSD-Menu-Functions
Following adjustments can do via the Quick-OSD-menu:
Brightnes
Contrast
Auto adjust
Invoke via key <SET>
Function
Contrast
Brightness
Adjustment/value
Range: 0 to 100
via key <+>/<->
Range: 0 to 100
via key <+>/<->
Description
Contrast adjustment
Brightness adjustment
Invoke via key <+>
Function
Adjustment/value
Description
Automatic
image
adjustment
Press key <+> to start the
adjustment
Perform an automatic image
adjustment. Adjustment of frequency,
phase and image position.
LCD-Monitor SCD1297
Page 15 / 19
DOC-No.: B3 0071D1.DOC
3.2.3.
OSD-Menu-Function
Invoke via key <MENUE>
Main menu
Function
Adjust function / value / range
Description
Picture 1
Brightness
setting range:
0 to 100 through key (+/-)
adjust brightness
Contrast
setting range:
0 to 100 through key (+/-)
adjust contrast
change contrast between dark and light colors
H Position
setting range:
0 to 100 through key (+/-)
move picture in horizontal direction
V-Position
setting range :
0 to 100 through key (+/-)
move picture in vertical direction
Phase
setting range :
0 to 31 through key (+/-)
adjust phase of input signal
Frequency
setting range :
950 to 1050 (dependent to picture)
through key (+/-)
adjust frequency of input signal
Sharpness
1, 2, 3, 4, 5
adjust sharpness of the picture by using no. 1 to 5
1=sharp, 5= soft
Gamma
Linear or CRT
correction of gamma curve
value of colors will be forwarded to the display
Color temperature
5000 - 6500 – 9300 - VAR
color temperature / adjust color
three defined and one adjustable color temperatures are for
selection
activate „VAR“ - for RGB shows up a adjustment beam.
0 to
100 % (50% correspond to factor 1)
Picture 2
Option 1
OSD
select between nine defined OSD positions f
define position OSD
OSD H-Position
setting range :
0 to 100 through key (+/-)
move OSD-menu in horizontal position
OSD V-Position
setting range :
0 to 100 through key (+/-)
move OSD-menu in vertical position
OSD timeout
5 ... 60 seconds
adjust time after the OSD menu is automatically fade out
the adjustment ensures between 5 to 60 s in steps of5 s.
OSD background
Opaque – Transparent
select background color of the OSD menu
you have the choice between transparent and colored
background.
Backlight
setting range :
0 to 100 through key (+/-)
adjust brightness ob backlight display
herewith you can match the brightness of the picture with the
brightness of the room.
Noise suppression
ON - OFF
Standard adjustment OFF.
By ON: Activate the function noise suppression. This function
suppresses interference at the sync signal lines to avoid
A new auto adjustment during short interference.
LCD-Monitor SCD1297
Page 16 / 19
DOC-No.: B3 0071D1.DOC
Main menu
Function
Adjust function / value / range
Description
Option 2
DPMS
ON – OFF
Display Power Management System (DPMS) on or off
If DMPS activated, the monitor is turn off (backlight) when a
synch signal is left. The screen is dark.
Source scan
OFF – ON – Standard
Standard: ON
Note: To scan new video source is not relevant because the
monitor has one RGB input source only.
Blank color
red – reen – blue – black
Choose the background color of the screen when no input signal
is present.
Display
–
Display resolution (not from the input source)
Info signal source
ON – OFF
Input source icon on or off
The icon is shown when input signal are changed. The icon
shows the following information’s:
signal source (e.g. RGB analog)
Mode number (internal mode number of the timing list)
Image resolution of the input signal
H- and V-frequency
Language
Englisch – German
Calibration
<+> press
OSD language
Adjustment of the internal A/D converter
(following the menu instruction)
Factory reset
<+> press
Reset of values like brightness, contrast,.. to default values
Installation RGBMode
<+> press
Enter a new timing which is not in the internal timing table. This
function should used, when the shown image resolution is not
the resolution are expect.
When press <+> the sub menu expect 9 timing parameter.
–
Show the H- and V-Frequency of the present input signal.
H/V-total, H/V-start
–
Show the used timing parameter of the present input signal
Option
Var. RGB-Mode inactive, Mode1, Mode2,
Mode3
Inaktiv: used the internal timing table only
Mode1: use the timing parameter and perform a complete auto
adjustment. (usually used)
Mode2: use the timing parameter and perform an auto
adjustment without an automatic image position adjustment.
Mode3: use the timing parameter and perform an auto
adjustment without an automatic frequency adjustment.
H-resolution
100 to 2000 through key (+/-)
Horizontal image resolution (important parameter)
V-resolution
100 to 2000 through key (+/-)
Vertical image resolution (important parameter)
H-total
100 to 2500 through key (+/-)
Whole pixel per line (important parameter)
H-Start
0 to 750 through key (+/-)
Number of Pixels from H-sync start to image start
V-Start
0 to 500 through key (+/-)
Number of lines from V-sync start to image start
Install
Utilities
When <+>,
H- and VFrequency
Info
<+> press
Activate the feed timing parameter
test pattern
<+> press
Show a test image
Firmware,
Resolution, Timing
–
Show the firmware version and timing data of the present input
signal
LCD-Monitor SCD1297
Page 17 / 19
DOC-No.: B3 0071D1.DOC
4 Technical Data
4.1 Display Module
Type
Diagonal
Display area (WxH)
Resolution
Pitch
Colours
Backlight
Brightness (typical)
Colour active TFT-LCD
30.8 cm (12.1")
246 x 184.5 mm²
800 x 600 pixels
0.33 x 0.33 mm²
262144
2xCCFT (Cold Cathode
Fluorescent Tube)
approx. 250 cd/m²
4.2 Power Supply
Input voltage
Power consumption (normal operation)
Power consumption (StandBy)
11.4 – 12.6 VDC
approx. 18 W
approx. 5 W
4.3 Operating Conditions
Operating temperature
Storage temperature
Humidity
+5 to +45°C
-20 to +60°C
max. 95% (non condensing)
4.4 Protection
Protection Class
Front screen in E(ET) and R(RT)
LCD-Monitor SCD1297
IP20
IP65
Page 18 / 19
DOC-No.: B3 0071D1.DOC
4.5 Enclosure
Weight
Enclosure material
Enclosure colour
approx. 3.2 kg
steel
light basic
4.6 Input Signals
Level (Video)
Bandwidth
Impedance
Synchronisation
0.7Vss RGB analogue at 75Ω
140Mhz (-3dB)
75Ω
Sep. Sync. (TTL)
Sync on green
Composite Sync
30 to 97 kHz
50 to 100 Hz**
H-Frequency
V-Frequency
4.7 EU Declaration of Conformity on EMC
Product
LCD-Monitor SCD 1297
Test foundations
EU framework guidelines
Harmonised
used
standards EN 55022
+A1/EN55022/A1
EN 50082-2
EN 60950
LCD-Monitor SCD1297
No. 89/336/EWG
No. 92/031/EWG
No. 73/23/EWG
No. 93/68/EWG
Edition 05/1995
Edition 08/1994
Edition 02/1996
Interference emissions
Edition 11/1997
Safety
Page 19 / 19
Interference resistance
DOC-No.: B3 0071D1.DOC