C, CS, CT, CWTF,
CRT, CRTF Series
Including
DV, MV, APS/TC/TS,
Single CW & Twins
Supercedes Service Manual: 41711.0000
SERVICE & REPAIR MANUAL
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
41711.0001A+ 02/10 ©2009 Bunn-O-Matic Corporation
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) All equipment other than as specified below: 2 years parts and 1 year labor.
2) Electronic circuit and/or control boards: parts and labor for 3 years.
3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.
4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis:
parts and labor for 3 years or 30,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by
it will be commercially free of defects in material and workmanship existing at the time of manufacture and
appearing within the applicable warranty period. This warranty does not apply to any equipment, component or
part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect,
alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is
conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone
at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by
BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior
authorization from BUNN that the defective equipment is under warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR
ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN
are not authorized to make modifications to this warranty or to make additional warranties that are binding on
BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and
should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its
exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts
and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective
components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace
the equipment or refund the purchase price for the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF
THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S
SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales,
loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute
equipment, facilities or services, or any other special, incidental or consequential damages.
AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress,
BUNN Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, BUNNlink,
Bunn-OMatic, Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr.
Brew stylized Dr. design, Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High
Intensity, iMIX, Infusion Series, Intellisteam, My Café, PowerLogic, Quality Beverage Equipment Worldwide,
Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE,
Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh, 392, Beverage Bar
Creator, Beverage Profit Calculator, BUNNSource, Coffee At Its Best, Digital Brewer Control, Nothing Brews Like
a BUNN, Pouring Profits, Respect Earth, Respect Earth with the stylized leaf and coffee cherry design, Signature
Series, Tea At Its Best, The Horizontal Red Line, Titan, Ultra are either trademarks or registered trademarks of
Bunn-O-Matic Corporation.
Page 2
41711.1 110909
Contents
Trouble Shooting.............................................................................................................. 4
Component Access ........................................................................................................ 10
Control Thermostat ........................................................................................................ 10
Electronic Thermostat .................................................................................................... 11
ON/OFF Switch ............................................................................................................... 12
Start Switch (Brew)........................................................................................................ 13
Solenoid (Inlet) .............................................................................................................. 14
Tank Heater .................................................................................................................... 16
Fill Basin ........................................................................................................................ 16
Tank Heater Switch ........................................................................................................ 18
Thermal Cut-Off ............................................................................................................. 20
Coil/Faucet ..................................................................................................................... 21
Limit Thermostat............................................................................................................ 22
Recovery Booster........................................................................................................... 23
Timer (Early Model) ....................................................................................................... 24
Freshness Timer (Early Models)..................................................................................... 25
Digital Brew Timer (Late Model) .................................................................................... 26
Warmer Elements........................................................................................................... 28
Schematic Wiring Diagrams.......................................................................................... 29
Page 3
41711.1 052009
TROUBLESHOOTING
A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems
encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic
Technical Service Department.
•
•
•
•
•
•
•
Inspection, testing, and repair of electrical equipment should be performed only by qualified service personnel.
All electronic components have 120 volt ac and low voltage dc potential on their terminals. Shorting of
terminals or the application of external voltages may result in board failure.
Intermittent operation of electronic circuit boards is unlikely. Board failure will normally be permanent. If
an intermittent condition is encountered, the cause will likely be a switch contact or a loose connection at a
terminal or crimp.
Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are
energized for more than ten minutes without a supply of water.
The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened. This will
help to avoid twists and kinks in the tubing.
Make certain that all plumbing connections are sealed and electrical connections tight and isolated.
This brewer is heated at all times. Keep away from combustibles.
WARNING – •
•
•
•
Exercise extreme caution when servicing electrical equipment.
Unplug the brewer when servicing, except when electrical tests are specified.
Follow recommended service procedures
Replace all protective shields or safety notices
PROBLEM
PROBABLE CAUSE
REMEDY
Brew cycle will not start
1. No water
Water lines and valves to the
brewer must be open.
2. No power or incorrect voltage
to the brewer
(A1) Check the terminal block for
120 volts across the black and
white terminals on two wire 120
volt brewers.
(A2) Check the terminal block
for 120 volts across the red and
white terminals and the black
and white terminal on three wire
120/240 volt brewers.
(A3) Check the terminal block for
200 volts on "B Series" brewers
or 240 volts on "A Series" brewers across the red and black
terminals.
(B) Check circuit breakers or
fuses.
Page 4
41711.1 052009
TROUBLESHOOTING (cont.)
PROBLEM
PROBABLE CAUSE
REMEDY
Brew cycle will not start (cont.)
3. ON/OFF Switch
Refer to Service - ON/OFF
Switch for testing.
4. Start Switch
Refer to Service - Start Switch
for testing procedures.
5. Timer
Refer to Service - Timer for testing procedures.
6. Solenoid Valve
Refer to Service - Solenoid Valve
for testing procedures.
7. Water strainer/flow control
(.222 GPM) Early models
(A) Direction of flow arrow must
be pointing towards brewer.
(B) Remove the strainer/flow
control and check for obstructions. Clear or replace.
Water is not hot
1. Tank Heater Switch
Refer to Service - Tank Heater
Switch for testing procedures.
2. (A) Limit Thermostat
(B) Thermal Cut-Off (Brewers
with Faucet)
CAUTION - Do not eliminate
or bypass limit thermostat or
thermal cut-off. Use only BOM
replacement parts.
Refer to Service - Limit Thermostat for testing procedures.
Thermal Cut-Off for testing
procedures.
3. Control Thermostat
Refer to Service - Control Thermostat for testing procedures.
4. Tank Heater
Refer to Service - Tank Heater
for testing procedures.
Page 5
41711.1 052009
TROUBLESHOOTING (cont.)
PROBLEM
PROBABLE CAUSE
REMEDY
Inconsistent beverage level in
dispenser
1. Strainer /flow control (.222
GPM) Early models.
(A) Direction of flow arrow must
be pointing towards the brewer.
(B) Remove the strainer/flow
control and check for obstruction. Clear or replace.
Consistently low beverage level
in the dispenser
2. Syphon System
The brewer must be level or
slightly lower in front to syphon
properly.
3. Lime Build-up
CAUTION - Tank and tank
components should be delimed
regularly depending on local water conditions. Excessive mineral build-up on stainless steel
surfaces can initiate corrosive
reactions resulting in serious
leaks.
Inspect the tank assembly for
excessive lime deposits. Delime
as required.
4. Water Pressure
The water pressure to the
brewer must be at least 20 psi
(138 kPa).
1. Timer
Timer must be set for at least
two minutes and fifteen seconds.
2. Strainer/flow Control (.222
GPM)
(A) Direction of flow arrow must
be pointing towards brewer.
(B) Remove the strainer/flow
control and check for obstructions. Clear or replace.
Spitting or excessive steaming
1. Lime Build-up
CAUTION - Tank and tank
components should be delimed
regularly depending on local water conditions. Excessive mineral build-up on stainless steel
surfaces can initiate corrosive
reactions resulting in serious
leaks.
Page 6
Inspect tank assembly for excessive lime deposits. Delime as
required.
41711.1 052009
TROUBLESHOOTING (cont.)
PROBLEM
PROBABLE CAUSE
REMEDY
Spitting or excessive steaming
(cont.)
2. Control Thermostat
Refer to Service - Control Thermostat for testing procedures.
Dripping from sprayhead
1. Syphon System
The brewer must be level or
slightly lower in front to syphon
properly.
2. Lime Build-up
CAUTION - Tank and tank components should be delimed
regularly depending on local
water conditions. Excessive mineral build-up on stainless steel
surfaces can initiate corrosive
reactions resulting in serious
leaks.
Inspect the tank assembly for
excessive lime deposits. Delime
as required.
3. Solenoid Valve
Remove the solenoid valve and
clear any obstructions. Rebuild
or replace the valve if necessary.
Water flows into tank continuously (ON/OFF Switch "ON")
1. Timer
Refer to Service - Timer for testing procedures.
Water flows into tank continuously (ON/OFF Switch "OFF")
1. Solenoid Valve
Remove the Solenoid Valve and
clean any obstruction. Rebuild
or replace the valve if necessary.
Beverage overflows dispenser
1.Dispenser
The dispenser must be completely empty before starting a
brew cycle.
2. Timer
Refer to Service - Timer for testing procedures.
3. Solenoid Valve
Remove the Solenoid Valve and
clean any obstruction. Rebuild
or replace the valve if necessary.
Page 7
41711.1 052009
TROUBLESHOOTING (cont.)
PROBLEM
PROBABLE CAUSE
REMEDY
Weak beverage
1. Filter Type
BUNN® paper filters must be used
for proper extraction.
2. Coffee Grind
A fine or drip grind must be used
for proper extraction.
3. Sprayhead
A six-hole stainless steel sprayhead must be used for proper
extraction.
4. Funnel Loading
The BUNN® paper filter must be
centered in the funnel and the
bed of ground leveled by gentle
shaking.
5. Water Temperature
Place an empty funnel on an empty
dispenser beneath the sprayhead.
Initiate a brew cycle and check the
water temperature immediately
below the sprayhead with a thermometer. The reading should not
be less than 195°F (76°C). Adjust
the control thermostat to increase
the water temperature. Replace if
necessary.
Dry coffee grounds remain in
the funnel
1. Funnel Loading
The BUNN® paper filter must be
centered in the funnel and the
bed of grounds leveled by gently
shaking.
Brewer is making unusal noises
1. Solenoid
The nut on the solenoid must
be tight or it will vibrate during
operation.
2. Plumbing Lines
Plumbing lines should not resting
on the counter top.
3. Water Supply
(A) The brewer must be connected
to a cold water line.
(B) Water pressure to the brewer
must not exceed 90 psi (620 kPa).
Install a regulator if necessary to
lower the working pressure to approximately 50 psi (345 kPa).
Page 8
41711.1 052009
TROUBLESHOOTING (cont.)
PROBLEM
PROBABLE CAUSE
REMEDY
Brewer is making unusal noises
(cont.)
4. Tank Heater
Remove and clean lime off the
tank heater.
Low beverage serving temperature
1. Warmer
Refer to Service - Warmer element for testing procedures.
2. ON/OFF Switch
Refer to Service - ON/OFF
Switch for testing procedures.
Page 9
41711.1 052009
SERVICE
This section provides procedures for testing and
replacing various major components used in this
brewer should service become necessary. Refer to
Troubleshooting for assistance in determining the
cause of any problem.
WARNING - Inspection, testing, and repair of electrical equipment should be performed only by qualified
service personnel. The brewer should be unplugged
when servicing, except when electrical tests are required and the test procedure specifically states to
plug-in the brewer.
COMPONENT ACCESS
WARNING - Disconnect the brewer from the power
source before the removal of any panel or the replacement of any component.
All components are accessible by the removal of
the top cover, front inspection panel, warmer plate(s)
and rear utility cover (Twins only).
CONTROL THERMOSTAT
3. Gently remove the capillary bulb and grommet
from the tank.
4. Check for continuity across the thermostat terminals. The indication must be:
a) Continuity with knob rotated fully clockwise.
b) No continuity with knob rotated fully counterclockwise. NOTE: First style does not have the ON/
OFF feature, simply check continuity.
If continuity is not present as described, replace control
thermostat.
If continuity is present as described, refer to the wiring
diagrams and check the brewer wiring harness.
Removal and Replacement:
1. Disconnect the control thermostat wires.
2. Remove the thermostat capillary bulb by firmly
pulling up on the capillary at the tank lid. This will
disengage the grommet from the tank lid.
3. Remove the one #8-32 screw securing the control
thermostat to the component bracket inside the
trunk.
4. Slide the grommet to the line 4.5" above the bulb
on the new capillary tube.
5. Insert the capillary bulb through the hole in the
tank lid and press the grommet firmly and evenly
so that the groove in the grommet fits into the tank
lid.
6. Carefully bend the capillary tube so that the tube
and bulb inside the tank are in the vertical position.
NOTE - The capillary tube must be clear of any electrical termination and not kinked.
7. Using #8-32 screw(s), secure the control thermostat to the component bracket inside the trunk.
8. For first type thermostat, refer to Wiring Diagrams
when reconnecting thermostat wires.
9. Adjust the control thermostat as required.
FIG. 10-1 CONTROL THERMOSTAT
Location:
The control thermostat is located inside the trunk
on the upper left side of the component bracket.
Test Procedures:
1. Disconnect the brewer from the power source.
2. Disconnect the leads from control thermostat.
NOTE: First type will only turn approximately one
turn. Clockwise to the stopper is approximately
180° F, maximum counterclockwise to stopper is
approximately 200° F.
Later types will be approximately 200° F when
turned maximum clockwise. Turning it counterclockwise until it clicks will turn off (open contacts).
Page 10
41711.1 052009
SERVICE (cont.)
OPTIONAL ELECTRONIC THERMOSTAT (ERT):
The ERT is located inside the trunk on the upper left
side of the component bracket.
Test Procedures:
1. Disconnect the brewer from the power source.
2. Gently remove the temperature sensor and grommet from the tank.
3. Check voltage across the blue wire from limit
thermostat and the white wire at the terminal
block. Connect the brewer to the power source.
The indication must be: 120Vac.
If voltage is not present as described, refer to the wiring
diagrams and check the brewer wiring harness
If voltage is present as described, proceed to #4.
First Type
Second Type
4. Disconnect the brewer from the power source.
5. With the temperature sensor and grommet still out
of the tank, check voltage across the black wire
to the heater and the white wire at the terminal
block. Connect the brewer to the power source.
The indication must be: 120Vac.
If voltage is not present as described, replace ERT.
If voltage is present as described, the ERT is functioning properly.
Removal and Replacement:
1. Disconnect the control thermostat wires.
2. Remove the temperature sensor by firmly pullingup on the metal sheath at the tank lid. This will
disengage the grommet from the tank lid.
3. Remove the one #8-32 screw securing the ERT to
the component bracket inside the trunk.
4. Slide the grommet to the top of the sheath.
5. Insert the temperature sensor through the hole
in the tank lid and press the grommet firmly and
evenly so that the groove in the grommet fits into
the tank lid.
6. Using the #8-32 screw, secure the ERT to the
component bracket inside the trunk.
7. For first type thermostat, refer to Wiring Diagrams
when reconnecting ERT wires.
8. Adjust the ERT as required.
Third Type
ERT
FIG 11-1 THERMOSTAT TERMINALS
NOTE: The ERT has a range of 170° - 210°F. Use care
not to set it too high or boiling could occur.
Page 11
41711.1 052009
SERVICE (cont.)
ON/OFF WARMER SWITCH
Removal and Replacement:
1. Remove the wires from the switch terminals.
2. Compress the clips inside the hood and gently
push the switch through the opening.
3. Push the new switch into the opening and spread
the clips to hold switch in the hood.
4. Refer to Fig.7 when reconnecting the wires.
FIG. 12-1 ON/OFF WARMER SWITCHES
Location:
The ON/OFF switch(s) are located on the front of
the hood.
(3) WHI to Neutral or RED to L2
(2) BLK to L1
Test Procedure:
1. Disconnect the brewer from the power source.
2. Viewing the switch from the back remove the white
or red wire from the upper terminal and the black
wire from the center terminal.
3. Check the voltage across the white wire or red wire
and the black wire with a voltmeter. Connect the
brewer to the power source. The indication must
be:
a) 120 volts ac for two wire 120 volt models and
three wire 120/240 volt models.
b) 200 to 240 volts ac for two wire 200 or 240 volt
models.
4. Disconnect the brewer from the power source.
(1) To Warmer
WARMER SWITCH
(1) LOAD (WARMER)
(2) LINE (L1)
(3) NEUTRAL (L2)
FIG. 12-2 WARMER SWITCH TERMINALS
If voltage is present as described, reconnect the white
or red wire and proceed to #5.
If voltage is not present as described, refer to the Wiring
Diagrams and check the brewer wiring harness.
5. With the black wire removed, remove the wire from
the lower terminal.
6. Check for continuity across the center and lower
terminal with the switch in the "ON" position.
Continuity must not be present when the switch
is in the "OFF" position.
If continuity is present as described, reconnect the
black wire to the center terminal and the remaining
wire to the lower terminal.
If continuity is not present as described, replace the
switch.
Page 12
41711.1 052009
SERVICE (cont.)
START SWITCHES
Test Procedure:
1. Disconnect the brewer from the power supply.
2. Disconnect the blue wire and the white/red wire
from the switch terminals.
3. Check for continuity across the two terminals on
the switch when it is held in the "pressed-in" position. Continuity must not be present across these
terminals in the released position.
CT SERIES
CRT/CRTF
If continuity is present as described, reconnect the blue
wire and the white/red to the switch terminals.
If continuity is not present as described, replace the
switch.
Removal and Replacement:
1. Remove the blue wire and white/red from the start
switch.
2. Remove round retaining nut from the front of
the switch and remove switch and internal tooth
lockwasher from the inside of the hood.
3. Push new switch with internal tooth lockwasher
through the hole in the hood and secure with round
retaining nut.
4. Refer to Fig. 11 when reconnecting the wires.
CRT/CRTF
FIG. 13-1 START SWITCH
WHI/RED to
Timer P3
BLU to Timer P1
Location: CRT/CRTF
On brewers w/out fresh light, the start switch is
located in the right front of the hood.
On brewers w/fresh light, the start switch is located
on the right side of the hood.
Location: CT/CWT/CWTF/TWINS
On most "CT" series brewers, the start switch is
located in the front of the hood.
On some "convertible" or "CS" brewers, the start
switch is located on either the right or left side of the
hood.
NOTE: Optional on the left and right side warmer
housings on 0/6 TWINS, connected in parallel to front
mounted start switches.
Page 13
CT/CWT/CWTF/TWINS
(3) WHI to Neutral or RED to L2
(2) BLK to L1
START SWITCH
FIG. 13-2 START SWITCH TERMINALS
41711.1 052009
SERVICE (cont.)
SOLENOID VALVES
6. Check the solenoid valve for coil action. Connect
the brewer to the power source. With "ON/OFF"
switch in the "ON' upper position press start switch
and listen carefully in the vicinity of the solenoid
valve for a" clicking" sound as the coil magnet
attracts.
7. Disconnect the brewer from the power source.
If the sound is heard as described and water will not
pass through the solenoid valve, there may be a blockage in the water line before the solenoid valve or, the
solenoid valve may require inspection for wear, and
removal of waterborne particles.
If the sound is not heard as described, replace the
solenoid valve.
EARLY MODELS
LATE MODELS
FIG. 14-1 SOLENOID VALVE
Location:
The solenoid valve is located inside the trunk on
the lower center part of the component bracket.
Test Procedures:
1. Disconnect the brewer from the power source.
2. Disconnect the white and black wires from the
solenoid valve. With the "ON/OFF" switch in the
"ON" upper position press the start switch.
3. Check the voltage across the white and black wires
with a voltmeter. Connect the brewer to the power
source. The indication must be:
a) 120 volts ac for two wire 120 volt models and
three wire 120/240 volt models.
b) 200 to 240 volts ac for two wire 200 or 240 volt
models.
4. Disconnect the brewer from the power source,
Removal and Replacement:
1. Remove the white and black from the solenoid
valve.
2. Turn off the water supply to the brewer.
3. Disconnect the water lines to and from the solenoid
valve.
4. Remove the two #8-32 screws securing the solenoid mounting bracket to the component bracket.
Remove solenoid bracket and solenoid valve as an
assembly.
5. Remove the two #10-32 screws and lockwashers securing the solenoid valve to the solenoid
bracket.
6. Using two #10-32 screws and lockwashers install new solenoid valve on solenoid mounting
bracket.
7. Using two #8-32 screws install solenoid valve and
bracket to the component bracket.
8. Securely fasten the water lines to and from the
solenoid valve.
9. Refer to Fig. 9 when reconnecting the wires.
If voltage is present as described, proceed to #5
If voltage is not present as described, refer to Wiring
Diagrams and check brewer wiring harness.
5. Check for resistance across the solenoid valve coil
terminals.
If resistance is present as described, reconnect the
white and black wire from the timer.
If resistance is not present as described, replace the
solenoid valve.
Page 14
WHI from Timer
BLK from Timer
FIG. 14-2 SOLENOID VALVE TERMINALS
41711.1 052009
SERVICE (cont.)
SOLENOID VALVES
Disassembly:
1. Use of the basin wrench 01060.0000 is recommended for disassembly of early style valves as
illustrated below.
2. Disconnect from power source and turn off the
water supply to the brewer.
3. Disconnect the water lines to and from the solenoid
valve.
4. Remove the two #8-32 screws securing the solenoid mounting bracket to the component bracket.
Remove solenoid bracket and solenoid valve as an
assembly.
5. Remove the two #10-32 screws and lock washers securing the solenoid valve to the solenoid
bracket.
6. Disassemble the valve according to the illustrations
that correspond to the particular valve you have.
7. On early style valves, leave the fittings installed
in the base to use as leverage. DO NOT CLAMP
THE BASE WITH LOCKING PLIERS AS THIS CAN
CAUSE DAMAGE!
8. Refer to Illustrated Parts Catalogs for replacement
solenoids and repair/rebuild kits.
120VAC - 334
FIG. 15-2 SECOND STYLE
120VAC - 247
240VAC - 757
120VAC - 1.18K
240VAC - 3.76K
FIG. 15-1 FIRST STYLE
FIG. 15-2 THIRD STYLE
Page 15
41711.1 052009
SERVICE (cont.)
FILL BASIN
TANK HEATER
FIG. 16-1 TANK HEATER
FIG. 16-2 TANK HEATER
Disassembly:
1. Use of the basin wrench 01060.0000 is recommended for removal of the fill basin.
2. Disconnect from power source and turn off the
water supply to the brewer.
3. Remove top cover.
4. Use the basin wrench (as shown above) turning
counterclockwise to remove inlet fitting.
5. Lift basin off of the tank inlet.
6. Use new inlet gasket when reinstalling.
Location:
The tank heater is located inside the tank and
secured to the tank lid.
Test Procedures:
1. Disconnect the brewer from the power supply.
2. Check the voltage across the black and white wires
on 120 volt models or the black and red wires for
120/240 volt models, 200 volt models and 240
volt models with a voltmeter. Connect the brewer
to the power source. The indication must be:
a) 120 volts ac for two wire 120 volt 20 amp
models .
b) 240 volts ac for three wire 120/240 volt models.
c) 200 to 240 volts ac for two wire 200 or 240 volt
models.
3. Disconnect the brewer from the power source.
If voltage is present as described, proceed to #4
If voltage is not present as described, refer to the Wiring Diagrams and check wiring harness.
4. Disconnect the wires from the tank heater terminals.
5. Check resistance value across tank heater terminals
and compare to chart.
Page 16
41711.1 052009
SERVICE (cont.)
TANK HEATER (Cont.)
HEATER
1800W-120V
1850W-220V
3500W-200V
3500W-240V
RESISTANCE
7.40 - 8.70
24.40 -28.40
10.70
15.36
-12.36
-17.90
TERMINAL TO SHEATH - INFINITE (OPEN)
FIG. 17-1 TANK HEATER RESISTANCE
If resistance is present as described, reconnect the
wires, the tank heater is ok.
If resistance is not present as described, replace the
tank heater.
NOTE- If any resistance is read between sheath and
either terminal, remove and inspect heater for cracks
in the sheath.
11. Install tank lid with limit thermostat, sprayhead
tube, tank heater, coil assembly (brewers with
faucet) and control thermostat with bracket (early
brewers only) using eight #8-32 hex nut.
12. Reconnect the inlet and outlet water lines to the
faucet coil assembly.
13. Secure sprayhead tube to hood using a hex nut.
14. Install sprayhead.
15. Reconnect the wires to the limit thermostat, tank
heater and control thermostat. See limit thermostat
and control thermostat sections in this manual
when reconnecting wires.
16. Install fill basin, secure with tank inlet fitting and
gasket. Insert water supply line through grommet
in fill basin.
17. Refer to Fig.13 when reconnecting the tank heater
wires.
Removal and Replacement:
1. Disconnect the water supply tube from the fill
BLK to Control Therbasin.
WHI to Terminal Block
mostat (Brewers W/
(White Insert on 230V
2. Remove the tank inlet fitting securing the fill basin
Out Faucet)
Two Wire Models)
Thermal Cut-Off to BLK
to the tank lid, remove fill basin and tank inlet
RED to Terminal Block
from Control Thergasket. Set all three parts aside for reassembly.
(Red Insert on 120/240V
mostat (Brewers W/
3. On brewers with faucet, shut-off water supply
Three Wire Models or
Faucet)
to the brewer and disconnect the inlet and outlet
200V and 240V Two
Wire Models
water lines to the faucet coil assembly.
4. Disconnect the black wire on the limit thermostat
from the tank heater switch. On late model brewers also disconnect the blue wire from the limit
thermostat to the control thermostat.
5. Disconnect the black wire and the white or red
wire from the tank heater terminals.
6. Remove sprayhead and the hex nut securing the
sprayhead tube to the hood. Set aside for reassembly.
FIG. 17-2 TANK HEATER TERMINALS
7. Remove the eight #8-32 nuts securing the tank lid
to the tank.
8. Remove the tank lid with limit thermostat, sprayhead tube, tank heater, coil assembly and control
thermostat w/bracket (early models only).
9 Remove the two hex nuts securing the tank heater
to the tank lid. Remove tank heater with gaskets
and discard.
10. Install new tank heater with gaskets on the tank
lid and secure with two hex nuts.
41711.1 052009
Page 17
SERVICE (cont.)
TANK HEATER SWITCH
5. With the tank heater switch in the "ON" upper position, check for continuity between the black wire
removed from the limit thermostat and the black
insert on the terminal block. Continuity should
not be present in the "OFF" lower position.
If continuity is present as described, the tank heater
switch is operating properly.
If continuity is not present as described, replace the
tank heater switch.
FIG 18-1 TANK HEATER SWITCH
Location:
The tank heater switch is located on the rear of
the brewer on the upper left side of the trunk.
Test Procedure:
1. Disconnect the brewer from the power source.
2. Disconnect the black wire from the limit thermostat.
3. With the tank heater switch in the "ON" position
and with a voltmeter, check the voltage between
the black wire removed from the limit thermostat
and the white wire or red wire on the tank heater.
Connect the brewer to the power source. The
indication must be:
a) 120 volts ac on two wire 120 volt models.
b) 240 volts ac on three wire 120/240 volt models.
c) 200 to 240 volts ac on 200 volt or 240 volt
models.
4. Disconnect the brewer from the power source.
If voltage is not present as described, proceed to
#5.
If voltage is present as described, the switch is working properly.
Removal and Replacement:
1. Shut off and disconnect the incoming water supply
to the brewer.
2. On automatic brewers gently remove the fill tube
from back of fill basin.
3. Remove the tank inlet fitting securing fill basin the
tank lid. Remove fill basin and gasket. Set all three
parts aside for reassembly.
4. On brewers with faucets, disconnect the water
supply to coil assembly and remove the tube from
the tank to the faucet.
5. Remove sprayhead and hex nut securing sprayhead
tube to the hood. Set aside for reassembly.
6. Disconnect the wires on the limit thermostat and
the tank heater and the control thermostat (early
models).
7. Gently pull the thermostat sensor and grommet
from the tank lid.
8. Insert a tube to the bottom of the tank and syphon
ALL of the water out.
9. Remove the two #8-32 screws securing the tank
assembly to the hood.
10. Lift tank and components out as an assembly and
set aside for reassembly.
11. Disconnect the two black wires from the tank heater
switch.
12. Remove the plastic facenut, hex facenut and the
switch indicator/guard bracket that secures tank
heater switch to the rear of the brewer. Remove
switch and discard.
13. Insert new tank heater switch through the hole in
the upper left rear of the trunk and secure with
switch indicator/guard bracket, hex facenut and
plastic facenut.
14. Reconnect the two black wires to the tank heater
switch terminals.
Page 18
41711.1 052009
SERVICE (cont.)
TANK HEATER SWITCH (cont.)
15. Set tank assembly inside the hood on mounting
brackets and secure with two #8-32 screws.
16. Reconnect the wires to the limit thermostat, tank
heater and the control thermostat. Refer to limit
thermostat, tank heater and control thermostat sections in this manual when reconnecting wires.
17. Brewers with faucet reinstall the faucet tube and
reconnect the water supply tube to the coil assembly.
18. Secure the sprayhead tube to the hood using hex
nut.
19. Install sprayhead.
20. Install fill basin, inlet gasket and secure to tank lid
with tank inlet fitting.
21. Carefully install water fill tube into the back of
the fill basin.
22. Reconnect and turn on the incoming water supply.
23. Refer to Fig. 15 when reconnecting the wires.
BLK to Limit Thermostat
BLK to Terminal Block
(Black Insert)
FIG. 19-1 TANK HEATER SWITCH TERMINALS
Page 19
41711.1 052009
SERVICE (cont.)
THERMAL CUT-OFF (Brewers W/Faucet)
Removal and Replacement:
1. Disconnect both ends of the TCO.
2. Install new thermal cut-off.
3. Refer to Fig. 17 when reconnecting wires.
Thermal Cut-Off from Tank
Heater to BLK Lead from
Control Thermostat
WHI or RED to
Terminal Block
Fig. 20-1 THERMAL CUT-OFF
Location:
The thermal cut-off (TCO) is a thermal fuse located
above the tank lid, connected to the tank heater.
NOTE: Installed only on tanks with coil faucet.
CE models have an additional TCO connected to the
other heater terminal.
Test Procedures:
1. Disconnect the brewer from the power source.
2. Disconnect both ends of the TCO.
3. Check for continuity across TCO with an ohmmeter.
120V, 120/240V
FIG. 20-3 TCO TERMINALS
RED to
Heater Switch
If continuity is present as described, the TCO is operating properly.
If continuity is not present as described, replace the
TCO.
Thermal Cut-Off from Tank
Heater to BLK Lead from
Control Thermostat
230V CE
FIG. 20-4 TCO TERMINALS
FIG. 20-2 TESTING TCO
Page 20
41711.1 052009
SERVICE (cont.)
COIL/FAUCET
Location:
The coil for the faucet is located in the tank.
Operation:
Water inside the coil is separate from the brewing water
and is always under line pressure. Brewing water in
the tank heats the submerged coil. Use of a coil faucet
during a brew cycle will not cause short potting, but is
limited to 8-10 ounces of hot water before the cooler
water is passed through coil.
Removal and Replacement:
1. Disconnect the brewer from the power and water
sources.
2. Turn and remove aerator assembly from bottom of
faucet. Clean parts of any mineral buildup. Install
new gasket when reassembling.
3. Remove the bonnet nut and remove handle assembly.
4. Remove the seat cup. Clean inside the faucet body
and install new seat cup.
BONNET NUT
SEAT CUP
FAUCET BODY
AERATOR
Fig. 21-1 COIL/FAUCET
Page 21
41711.1 052009
SERVICE (cont.)
LIMIT THERMOSTAT
If continuity is present as described, the limit thermostat
is operating properly.
If continuity is not present as described, replace the
limit thermostat.
Removal and Replacement:
1. Remove all wires from limit thermostat terminals.
2. Carefully slide the limit thermostat out from under
the retaining clip and remove limit thermostat.
3. Carefully slide the new limit thermostat into the
retaining clip.
4. Refer to the Fig. 5 when reconnecting the wires.
to Tank
Heater Switch
Lead from
Control Thermostat
FIG. 22-1 LIMIT THERMOSTAT
Location:
The limit thermostat is located inside the rear of
the hood on the tank lid.
Test Procedures:
1. Disconnect the brewer from the power source.
2. Disconnect the blue and black wires from the limit
thermostat.
3. Check for continuity across the limit thermostat
terminals with a ohmmeter.
Page 22
FIG. 22-2 LIMIT THERMOSTAT TERMINALS
41711.1 052009
contact terminals. Connect the brewer to the power
source. With the "ON/OFF" switch in the "ON" position and the start switch pressed and released,
check for continuity across relay terminals.
7. Disconnect the brewer from the power source.
RECOVERY BOOSTER RELAY (OPTIONAL)
If continuity is present as described, reconnect the blue
and black wires to the relay contact terminals.
If continuity is not present as described replace the
relay.
B = COIL to TIMER
6-9 = N.O. spare
A = COIL to TIMER
4-7 = N.O. to THERMOSTAT
4
7
Location
The recovery booster(s) are located inside the trunk
on the center of the component brackets just above
the solenoid valve. The coil is activated by the timer/
solenoid circuit. The contacts then close, bypassing
the mechanical thermostat, thereby allowing faster
heating of the incoming water in the tank.
A
FIG. 23-1 RECOVERY BOOSTER RELAY
Removal and Replacement:
1. Remove all wires from the relay.
2. Remove the two #8-32 screws securing the relay
mounting bracket to the component bracket. Remove relay bracket and relay as an assembly.
3. Remove the screw securing the relay to the relay
mounting bracket.
4. Install new relay to the component bracket.
5. Refer to Fig. 9 when reconnecting the wires.
EARLY MODELS
6
9
B
Test Procedures
1. Disconnect the brewer from the power source.
2. Disconnect the white and black wires from the coil
of the recovery booster relay.
3. With a voltmeter, check the voltage across the
white and the black wires. Connect the brewer
to the power source and initate a brew cycle. The
indication must be 120 volts ac.
4. Disconnect the brewer from the power source.
LATER MODELS
If voltage is present as described, proceed to #5.
If voltage is not present as described, refer to Wiring
Diagrams and check the brewer wiring harness.
1 = COIL to TIMER
8
5. Check the resistance across the coil's terminals.
If resistance is present as described in FIG 9, reconnect
the white and black wires to the coil.
If resistance is not present as described, replace the
relay.
6. Disconnect the blue and black wires from the relay
Page 23
1
6
6-8 = N.O. not used
4
2
0
2-4 = N.O. to THERMOSTAT
0 = COIL to TIMER
FIG. 23-2 BOOSTER RELAY TERMINALS
41711.1 052009
SERVICE (cont.)
TIMER (Early Models)
To Main Wiring Harness
To Solenoid Valve
EARLY STYLE
FIG. 24-1 TIMER TERMINALS
Location:
The timer is located inside the front of the trunk
on the upper right side of component bracket.
Test Procedure.
1. Disconnect the brewer from the power source.
2. Disconnect the polarized, three pin connector from
the brewer wiring harness.
3. With a voltmeter, check the voltage across sockets
P2 & P3 (white and white/red wires) of the female
connector when the "ON/OFF" switch is in the "ON"
position (upper). Connect the brewer to the power
source. The indication must be:
a) 120 volts ac for two wire 120 volt models and
three wire 120/240 volt models.
b) 200 to 240 volts ac on two wire 200 volt or 240
volt models.
4. Disconnect the brewer from the power source.
If voltage is present as described, proceed to #5.
If voltage is not present as described, refer to the
Wiring Diagrams and check the brewer wiring harness.
Connect the brewer to the power source. The
indication must be:
a) 120 volts ac for two wire 120 volt models and
three wire 120/240 volt models.
b) 200 to 240 volts ac for two wire 200 volt or 240
volt models.
6. Disconnect the brewer from the power source.
7. Reconnect the three pin connector from main
wiring harness to the timer.
If voltage is present as described, proceed to #8
If voltage is not present as described, refer to Wiring
Diagrams and check the start switch and brewer wiring harness.
8. With a voltmeter, check the voltage across the
black and white wires when the "ON/OFF" switch
is in the "ON" position (upper) and the "START"
switch is pressed to the "START" position and
released. Connect the brewer to the power source.
The indication must be:
a) 120 volts ac for approximately 20 seconds for
two wire 120 volt models and three wire 120/240
volt models.
b) 200 to 240 volts ac for approximately 20 seconds
for two wire 200 volt or 240 volt models.
If voltage is present as described, the brew timer is
operating properly. Reconnect the polarized, three
pin connector.
If voltage is not present as described, replace the
timer.
Removal and Replacement:
1. Separate all connectors between the brewer wiring
harness and the timer.
2. Remove the one #8-32 screw securing timer to
component bracket.
3 Install new timer circuit board as described in Late
Model Timer section on the following pages.
4. Refer to Fig. 21 when reconnecting the wires.
5. Install the Timer Setting decal provided with the
replacement timer kit, below the schematic on the
inside of the front access panel.
6. Adjust the timer as required. Refer to Late Model
Timer section on the following pages.
5. Check the voltage across the sockets P1 & P2
(blue and white wires) of the female connector
with a voltmeter when the "ON/OFF" switch is in the
"ON" position (upper) and start switch pressed.
Page 24
41711.1 052009
SERVICE (cont.)
FRESHNESS TIMER (Early Models)
If voltage is present as described, proceed to #4.
If voltage is not present as described, refer to the
Wiring Diagrams and check the brewer wiring harness.
4. Check the voltage across the T3 and T4 (white/
orange and white/blue wires) of the fresh timer
with a voltmeter when the "ON/OFF" switch is in
the "ON" position (upper) and start switch pressed.
Connect the brewer to the power source. The
indication must be: (when solenoid is activated)
a) 120 volts ac for two wire 120 volt models and
three wire 120/240 volt models.
b) 200 to 240 volts ac for two wire 200 volt or 240
volt models.
5. Disconnect the brewer from the power source.
6. Reconnect the three pin connector from main
wiring harness to the timer.
FIG. 25-1 TIMER TERMINALS
Location:
The freshness timer is located inside the front of
the trunk on the component bracket.
If voltage is present as described, proceed to #7
If voltage is not present as described, refer to Wiring
Diagrams and check the start switch and brewer wiring harness.
7. With a voltmeter, check the voltage across connector P1 after the delay period (JP1 set to "STEADY",
and JP2 set to "ON"). The indication must be:
3-5 volts dc (when solenoid is activated).
Operation:
The freshness timer activates an LED on the
control panel after a predetermined amount of time
(after the brew cycle) to indicate carafe on warmer
too long.
Settings: Default settings underlined
JP1: Choose between flashing LED or steady.
JP2: Choose whether the LED stays ON, then
turns off; or is off, then turns on at the end of delay.
R4: Delay time adjustment, 20-60 minutes.
Test Procedure.
1. Disconnect the brewer from the power source.
2. With a voltmeter, check the voltage across T1 & T2
(black & white wires) of the fresh timer. Connect
the brewer to the power source. The indication
must be:
a) 120 volts ac for two wire 120 volt models and
three wire 120/240 volt models.
b) 200 to 240 volts ac on two wire 200 volt or 240
volt models.
3. Disconnect the brewer from the power source.
If voltage is present as described, the fresh timer
is operating properly. If voltage is not present as
described, replace the timer. NOTE: The freshness
timer is no longer available.
Removal and Replacement:
1. Disconnect the brewer from the power source.
2. Disconnect all four connectors from the timer.
2. Remove the two #8-32 screws securing timer to
component bracket.
6. Adjust the timer as required. Refer to Late Model
Timer section on the following pages.
Page 25
41711.1 052009
SERVICE (cont.)
DIGITAL BREW TIMER (Late Models)
4. With a voltmeter, check the output voltage across
terminals TL2 and TL4 when the "ON/OFF" switch
is in the "ON" position. Connect the brewer to the
power source and press the "START" switch. The
indication must be as follows:
a) 120 volts ac for two wire 120 volt models and
three wire 120/240 volt models.
b) 200 to 240 volts ac for two wire 200 volt or 240
volt models.
If voltage is present as described, the timer is operating properly. Reset the timer as required, to obtain the
desired brew volume.
If voltage is not present as described, proceed to
#6.
FIG. 26-1 DIGITAL BREW TIMER
Location:
The timer is located inside the front of the trunk
on the upper right side of component bracket.
Test Procedure
NOTE: Do not remove or install wires while timer board
is installed. Pressure applied to one side may cause
damage to the board.
1. Disconnect the brewer from the power source and
remove the front access panel.
2. With a voltmeter, check the supply voltage across
terminals TL1 and TL2 when the "ON/OFF" switch
is in the "ON" position. Connect the brewer to the
power source. The indication must be:
a) 120 volts ac for two wire 120 volt models and
three wire 120/240 volt models.
b) 200 to 240 volts ac on two wire 200 volt or
240 volt models.
3. Disconnect the brewer from the power source.
If voltage is present as described, proceed to #4.
If voltage is not present as described, refer to the Wiring Diagrams and check the wiring harness.
6. With a voltmeter, check the input start voltage
across terminals TL2 and TL5 when the "ON/OFF"
switch is in the "ON" position. Connect the brewer
to the power source and press the "START" switch.
The indication must be as follows:
a) 120 volts ac for two wire 120 volt models and
three wire 120/240 volt models.
b) 200 to 240 volts ac on two wire 200 volt or
240 volt models.
If voltage is not present as described, refer to the
Wiring Diagrams and check the wiring harness to the
start switch.
If voltage is present as described, disconnect the brewer
from the power source and replace the timer.
Removal and Replacement:
1. Remove the two #8-32 screws securing circuit
board to the mounting bracket.
2. Remove circuit board and spacers (as required).
3. Remove all wires from the timer.
4. Attach all wires to the replacement timer board
prior to installation to the component mounting
bracket. Refer to FIG. 21 when reconnecting the
wires.
5. Install new circuit board with spacers (as required)
to the component mounting bracket.
6. Adjust the timer as described in the next section.
Page 26
41711.1 052009
SERVICE (cont.)
DIGITAL BREW TIMER (Late Models)(cont.)
Timer Setting:
NOTE: Prior to setting or modifying volumes, check
that the brewer is connected to water supply, the
tank is properly filled, and a funnel and server are in
place.
NOTE: All volume settings must be done with the
sprayhead installed.
1. Modifying brew volumes. To modify a brew volume, first check that the SET/LOCK switch is in the
“SET” position on the circuit board.
To increase a brew volume, place the ON/OFF
switch in the “ON” position, press and hold the START
switch until three clicks are heard. Release the switch
and press it again one or more times. (Failure to release the switch within two seconds after the third click
causes the volume setting to be aborted and previous
volume setting will remain in memory) Each time the
switch is pressed, two seconds are added to the brew
time period. Allow the brew cycle to finish in order to
verify that the desired volume has been achieved.
NOTE: Several ounces of water will continue to syphon from the tank after turning the switch “OFF”.
The brewer remembers this volume and will continue
to brew batches of this size until the volume setting
procedure is repeated.
NOTE: When brewing coffee, volume will decrease
due to absorption by the coffee grounds.
3. Setting programming disable feature. If it becomes necessary to prevent anyone from changing
brew time once programmed, you can set the SET/
LOCK switch to the “LOCK” position. This will prevent
any further programming until switch is once again
put into the “SET” position.
To decrease a brew volume, place the ON/OFF
switch in the “ON” position, press and release the
START switch once for every two-second interval to
be removed from the total brew time period; then immediately press and hold down the START switch until
three clicks are heard. Release the switch. (Failure to
release the switch within two seconds after the third
click causes the volume setting to be aborted and
previous volume setting will remain in memory). Allow the brew cycle to finish in order to verify that the
desired volume has been achieved.
2. Setting brew volumes. To set a brew volume,
first check that the SET/LOCK switch is in the “SET”
position on the circuit board. Place the ON/OFF switch
in the “ON” position, press and hold the START switch
until three distinct clicks are heard and then release
the switch. (Failure to release the switch within two
seconds after the third click causes the volume setting
to be aborted and previous volume setting will remain
in memory.
View the level of the liquid being dispensed. When
the desired level is reached, turn the ON/OFF switch
to “OFF”.
Page 27
BLU wire to TL5 from start switch
WHI/GRN wire to TL4 from solenoid
WHI/BLU wire to TL3 from solenoid
WHI wire to TL2 from N/L2
WHI/RED wire to TL1 from on/off switch
FIG. 27-1 DIGITAL TIMER WIRING
41711.1 052009
SERVICE (cont.)
WARMER ELEMENT(S)
4. Check the resistance across the two terminals on
the warmer element. NOTE: There should be no
resistance reading between the heater sheath and
either terminal. Refer to the following chart.
If resistance is to specification, reconnect the two
wires to the warmer element.
If resistance is not to specification, replace the warmer
element.
FIG. 28-1 WARMER ELEMENTS
Location:
The warmer element(s) is located under the warmer
plate.
Test Procedures:
1. Disconnect the brewer from the power source.
2. With a voltmeter, check voltage across the two
wires at the warmer element with the "ON/OFF"
switch in the "ON" position. Connect the brewer
to the power source. The indication must be 120
volts ac for two wire 120 volt models and three
wire 120/208 and 120/240 volt models, or 230
volts ac for two wire 230 volt models.
3. Disconnect the brewer from the power source.
Removal and Replacement:
1. Remove the three #4-40 screws securing the
warmer assembly to the brewer.
2. Lift the warmer assembly from the brewer.
3. Disconnect the two wires from the warmer element
terminals.
4. Remove the two #8-32 nuts securing the warmer
element to the warmer plate.
5. Securely install new warmer element.
6. Reconnect the two wires to warmer element terminals.
7. Securely install warmer assembly on the brewer.
WHI/RED to ON/OFF Switch (Center Warmer)
YEL to ON/OFF Switch (Left Front Warmer)
WHI/VIO to ON/OFF Switch (Left Rear Warmer)
BRN/BLk to ON/OFF Switch (Right Front Warmer)
VIO to ON/OFF Switch (Right Rear Warmer)
WHI to Terminal Block (120V or
120/240V Brewers)
RED to Terminal Block (200V or
240V Brewers
If voltage is present as described, proceed to #4.
If voltage is not present as described, refer to Wiring
Diagrams and check wiring harness.
FIG. 28-3 WARMER ELEMENT TERMINALS
WARMER
100W-120V
100W-220V
100W-200V
RESISTANCE
132 - 152
450 - 532
372 - 432
TERMINAL TO SHEATH - INFINITE (OPEN)
FIG. 28-2 WARMER ELEMENTS
Page 28
41711.1 052009
SCHEMATIC WIRING DIAGRAM
CRT5, & CRTF5
L1
HEATER
SWITCH
BLK
LIMIT
THERMOSTAT
BLK
BLU
SWITCH AND
THERMOSTAT
N
GREEN
(FAUCET OPTION
ONLY)
THERMAL
CUT-OFF
TANK HEATER
BLK
L2
WHI (MODEL 20)
RED (MODEL 35)
WHI
WHI
"KEEP WARM" HEATER
ON/OFF SWITCH
WHI
WHI
WHI/RED
BLK
LOWER CENTER WARMER
START SWITCH
WHI/RED
BLU
SOL
WHI/RED
WHI/BLU
T1 T5 T3
BREW
TIMER
ON/OFF SWITCH
BLK
T4
T2
WHI/GRN
WHI
WHI
YEL
LEFT FRONT
WARMER
ON/OFF SWITCH
WHI
WHI
WHI/VIO
BLK
LEFT REAR
WARMER
ON/OFF SWITCH
WHI
BRN/BLK
BLK
RIGHT FRONT
WARMER
ON/OFF SWITCH
BLK
WHI
WHI
VIO
RIGHT REAR
WARMER
120/240 VOLTS AC 3 WIRE
120 VOLTS AC 2 WIRE
SINGLE PHASE
10476.0000G 07/03 © 1990 BUNN-O-MATIC CORPORATION
Page 29
41711.1 052009
SCHEMATIC WIRING DIAGRAM
CRT5A, & CRTF5A
L1
L2
GRN/YEL
HEATER
SWITCH
BLK
LIMIT
THERMOSTAT
BLU
BLK
(MODEL CRTF5A ONLY)
THERMAL
CUT-OFF
BLK
SWITCH AND
THERMOSTAT
TANK HEATER
WHI
RED
WHI
"KEEP WARM" HEATER
ON/OFF SWITCH
RED
WHI/RED
BLK
RED
LOWER CENTER WARMER
START SWITCH
SOL
WHI/RED
BLU
WHI/RED
WHI/BLU
T1 T5 T3
T4
BREW T2
TIMER
ON/OFF SWITCH
BLK
WHI/GRN
RED
RED
YEL
LEFT FRONT
WARMER
ON/OFF SWITCH
RED
RED
WHI/VIO
BLK
LEFT REAR
WARMER
ON/OFF SWITCH
BLK
RED
BRN/BLK
RIGHT FRONT
WARMER
ON/OFF SWITCH
BLK
RED
RED
VIO
RIGHT REAR
WARMER
240 VOLTS AC 2 WIRE
SINGLE PHASE
10477.0000H 07/03 © 1990 BUNN-O-MATIC CORPORATION
Page 30
41711.1 052009
SCHEMATIC WIRING DIAGRAM
CRT5B, & CRTF5B
L1
L2
GREEN
HEATER
SWITCH
BLK
LIMIT
THERMOSTAT
BLU
BLK
(MODEL CRTF5B ONLY)
THERMAL
CUT-OFF
BLK
SWITCH AND
THERMOSTAT
TANK HEATER
ON/OFF SWITCH
BLK
WHI
WHI
WHI/RED
WHI
LOWER CENTER WARMER
START SWITCH
SOL
WHI/RED
BLU
WHI/RED
WHI/BLU
T1 T5 T3 T4
BREW
T2
TIMER
ON/OFF SWITCH
WHI/GRN
WHI
WHI
YEL
BLK
LEFT FRONT
WARMER
ON/OFF SWITCH
BLK
WHI
WHI
WHI/VIO
LEFT REAR
WARMER
ON/OFF SWITCH
WHI
BRN/BLK
BLK
RIGHT FRONT
WARMER
ON/OFF SWITCH
BLK
WHI
WHI
VIO
RIGHT REAR
WARMER
200 VOLTS AC 2 WIRE
SINGLE PHASE
10477.0001H 07/03 © 1993 BUNN-O-MATIC CORPORATION
Page 31
41711.1 052009
RED Model 35
WHI Model 20
WHI Model 15 & 35
MAIN ON/OFF SWITCH
(Late 20 & 35
Models only)
BLK Model 20 & 35
READY INDICATOR
BLU
BLK
HEATER
SWITCH
LIMIT
THERMOSTAT
BLK
BLK
SW. & THERMOSTAT
(FAUCET OPTION ONLY)
THERMAL
FUSE
BLK
BLK
N
L2
WHI Model 20
BLK Model 15
GREEN
BLK-14
BLK
BLK
L1
SCHEMATIC WIRING DIAGRAM
CW/CWT/CWTF - APS/TS/TSR/TC
WHI-14 Model 20
RED-14 Model 35
TANK HEATER
WHI Model 15
WHI
WHI
"KEEP WARM" HEATER
OPTIONAL AUTOMATIC BREW CIRCUIT
ON/OFF
SWITCH
WHI
START SWITCH
WHI/BLU
BLK
BLU
WHI/RED
SOL
WHI/RED
T1 T5 T3
BREW
TIMER
120/240 VOLTS AC 3 WIRE
120 VOLTS AC 2 WIRE
SINGLE PHASE
T4 WHI/GRN
T2
WHI
10693.0000G 02/07 © 1993 BUNN-O-MATIC CORPORATION
Page 32
41711.1 052009
SCHEMATIC WIRING DIAGRAM CW-TS & CW-APS ERT
THERMOSTAT
SWITCH
GRN
TAN
L1
E.R.T
ASSY.
HEATER
SWITCH
BLK
WHI
LIMIT
THERMOSTAT
BLK
(FAUCET OPTION ONLY)
THERMAL FUSE
BLU
N L2
TAN
BLU
BLK
TANK HEATER
RED (3-WIRE MODELS)
WHI (2-WIRE MODELS)
READY INDICATOR
BLU
BLK
50W
WHI
WHI
"KEEP WARM" HEATER
AUXILIARY OUTLET
BLK
WHI
(200 WATT MAXIMUM)
OPTIONAL AUTOMATIC BREW CIRCUIT
ON/OFF
SWITCH
WHI
START SWITCH
BLK
P1 BLU
BLU
WHI/RED
WHI/RED
P3
P1, P2, & P3 ARE PINS OF A
POLARIZED THREE-PIN
CONNECTOR.
120/240 VOLTS AC 3 WIRE
120 VOLTS AC 2 WIRE
SINGLE PHASE
BLK
BLK
BREW
TIMER
SOL
WHI
WHI P2
WHI
10693.0001C 9/96 © 1996 BUNN-O-MATIC CORPORATION
Page 33
41711.1 052009
SCHEMATIC WIRING DIAGRAM FOR CWT-APS MV,
CWTF-APS MV, CWTF-TS MV, CWTF-TSR MV
Page 34
41711.1 052009
Page 35
41711.1 052009
Page 36
41711.1 052009
Page 37
41711.1 052009
BLK
Page 38
41711.1 052009
Page 39
41711.1 052009
GRN
LT. READY INDICATOR
BLK
BLK
BLU
LT. SW. & THERMOSTAT
BLU
LT.LIMIT
THERMOSTAT
SW1
MAIN ON/OFF SWITCH
(Late Models only)
BLK
(FAUCET)
THERMAL
SAFETY FUSE
BLK
RED
BLK
LEFT TANK HEATER
BLK
RED
WHI
WHI
LEFT "KEEP WARM" HEATER
RT. READY INDICATOR
RED
BLK
BLK
BLU
BLK
BLK
RT. SW. & THERMOSTAT
BLU
RT. LIMIT
THERMOSTAT
SW2
RIGHT TANK HEATER
BLK
RED
WHI
WHI
RIGHT "KEEP WARM" HEATER
RED
SW3
RED
WHI
WHI/RED
WHI/RED
LEFT LOWER WARMER
WHI
WHI
WHI
P1-1
P1-2
SW4
BLK
N
L2
WHI
BLK
L1
RED
SCHEMATIC WIRING DIAGRAM
CWT/CWTF TWIN 0/2, 2/2, 4/2 & CWT TWIN-APS
WHI
WHI/GRN
WHI/GRN
RIGHT LOWER WARMER
WHI
P1-3
SW5
BLU
WHI/RED
WHI/BLU
WHI/RED
SW6
BLU
WHI/GRN
WHI/BLU
BLK
RT
SOL
T1 T5 T3 T4
LEFT T2
LT
SOL
WHI/GRN
WHI
BREW TIMER
T1 T5 T3 T4 WHI/GRN
RIGHT T2
MODELS 2/2 & 4/2 ONLY
(NOT AVAILABLE ON CWT TWIN-APS)
WHI
BREW TIMER
RED
SW7
RED
WHI
YEL
P4-2
YEL
WHI
WHI
LEFT TOP FRONT
WARMER
SW8
WHI/YEL P4-3
BLK
WHI P4-1
WHI/YEL
WHI
WHI
RIGHT TOP FRONT WARMER
MODEL 4/2 ONLY
RED
SW9
RED
WHI
WHI/VIO
WHI
WHI P5-1
WHI
LEFT TOP REAR WARMER
SW10
BLK
P5-3 WHI/VIO
WHI
WHI/BRN P5-2 WHI/BRN
WHI
RIGHT TOP REAR WARMER
120/240 VOLTS AC
3 WIRE + GND
SINGLE PHASE
10736.0000L 03/07 © 1993 BUNN-O-MATIC CORPORATION
Page 40
41711.1 052009
GRN
LT. READY INDICATOR
BLK
BLK
BLU
LT. SW. & THERMOSTAT
BLU
LT.LIMIT
THERMOSTAT
SW1
MAIN ON/OFF SWITCH
(Late Models only)
BLK
(FAUCET)
THERMAL
SAFETY FUSE
BLK
RED
BLK
LEFT TANK HEATER
BLK
RED
WHI
WHI
LEFT "KEEP WARM" HEATER
RT. READY INDICATOR
BLK
BLK
BLU
RT. SW. & THERMOSTAT
BLU
RT. LIMIT
THERMOSTAT
BLK
BLK
RED
SW2
RIGHT TANK HEATER
BLK
RED
WHI
WHI
Models after 2/210
RIGHT "KEEP WARM" HEATER
SW3
BLK
WHI
WHI/RED
WHI/RED
LEFT LOWER WARMER
WHI
WHI
WHI
P1-1
P1-2
SW4
BLK
N
L2
WHI
BLK
L1
RED
SCHEMATIC WIRING DIAGRAM
CWT/CWTF TWIN 0/2, 2/2, 4/2 & CWT TWIN-APS
WHI
WHI/GRN
WHI/GRN
RIGHT LOWER WARMER
WHI
P1-3
SW5
BLU
WHI/RED
WHI/BLU
WHI/RED
SW6
BLU
WHI/GRN
WHI/BLU
BLK
RT
SOL
T1 T5 T3 T4
LEFT T2
LT
SOL
WHI/GRN
WHI
BREW TIMER
T1 T5 T3 T4 WHI/GRN
RIGHT T2
MODELS 2/2 & 4/2 ONLY
(NOT AVAILABLE ON CWT TWIN-APS)
WHI
BREW TIMER
RED
SW7
RED
WHI
YEL
P4-2
YEL
WHI
WHI
LEFT TOP FRONT
WARMER
SW8
WHI/YEL P4-3
BLK
WHI P4-1
WHI/YEL
WHI
WHI
RIGHT TOP FRONT WARMER
MODEL 4/2 ONLY
RED
SW9
RED
WHI
WHI/VIO
WHI
WHI P5-1
WHI
LEFT TOP REAR WARMER
SW10
BLK
P5-3 WHI/VIO
WHI
WHI/BRN P5-2 WHI/BRN
WHI
RIGHT TOP REAR WARMER
120/240 VOLTS AC
3 WIRE + GND
SINGLE PHASE
10736.0000M 01/10 © 1993 BUNN-O-MATIC CORPORATION
Page 41
41711.1 020410
SCHEMATIC WIRING DIAGRAM CWTFA
TWIN 2/2 & 4/2
L1
LEFT TANK HEATER
BLK
L3
RED
LT. SW. & THERMOSTAT
BLU
(FAUCET)
THERMAL
SAFETY FUSE
BLK
BLK
L2
GRN/YEL
LT. READY INDICATOR
LT. LIMIT
THERMOSTAT
BLU
SW1
BLU
BLU
RED
WHI
WHI
LEFT "KEEP WARM" HEATER
RT. READY INDICATOR
BLK
BLK
BLK
RIGHT TANK HEATER
RED
RT. SW. & THERMOSTAT
BLU
BLK
BLK
RT. LIMIT
THERMOSTAT
BLU
WHI
WHI
RED
RED P1-1
RED
WHI/GRN P1-3 WHI/GRN
RED
SW5
RIGHT LOWER WARMER
BLU P2-1BLU/BLK
WHI/RED
P2-3 BLK
WHI/RED
SW6
BLU P3-1BLU/BLK
WHI/GRN
P3-3 BLK
WHI/GRN
WHI/BLU
WHI/BLU
YEL
P4-2
YEL
P3-2
RED P4-1
LEFT TOP FRONT
WARMER
WHI/YEL P4-3
WHI/YEL
BLK
RED
RED
RED
SW9
RED
WHI/VIO
SW10
RED
RIGHT TOP FRONT WARMER
MODEL 4/2 ONLY
BLK
RED
RED
RED
SW8
P2-2
BREW TIMER
BREW TIMER
SW7
LT
SOL
T1 T5 T3 T4 WHI/GRN
WHI
LEFT T2
RT
SOL
T1 T5 T3 T4 WHI/GRN
RIGHT T2 WHI
BLK
RED
LEFT LOWER WARMER
SW4
BLK
RED
RED
WHI/RED P1-2 WHI/RED
BLK
BLU
RIGHT "KEEP WARM" HEATER
SW3
BLK
SW2
BLU
P5-3 WHI/VIO
RED
LEFT TOP REAR WARMER
RED P5-1
RED
RED
WHI/BRN P5-2 WHI/BRN
RED
RIGHT TOP REAR WARMER
230 VOLTS AC 3 WIRE
THREE PHASE
10736.0001G 12/00 © 1993 BUNN-O-MATIC CORPORATION
Page 42
41711.1 052009
SCHEMATIC WIRING DIAGRAM
CWTFA & CWTFB TWIN 2/2 & 4/2
L1
L2
LT. READY INDICATOR
RED
BLK
BLK
(FAUCET)
THERMAL
FUSE
BLK
LT. SW. & THERMOSTAT
BLU
LT.LIMIT
THERMOSTAT
SW1
GRN/YEL
BLK
BLU
BLK
LEFT TANK HEATER
RED
RIGHT TANK HEATER
RED
RT. READY INDICATOR
RED
BLK
BLK
BLK
RT. SW. & THERMOSTAT
BLU
RT. LIMIT
THERMOSTAT
SW2
BLK
BLU
BLK
SW3
RED
WHI/RED P1-2 WHI/RED
BLK
RED
RED
LEFT LOWER WARMER
SW4
RED
WHI/GRN P1-3 WHI/GRN
BLK
RED P1-1
RED
SW5
RIGHT LOWER WARMER
SW6
P2-1
WHI/RED
BLU
WHI/RED
P2-3
BLU P3-1BLU/BLK
WHI/GRN
P3-3
WHI/GRN
BLK
BLU/BLK
BLK
WHI/BLU
T1 T5 T3
WHI/BLU
RT
SOL
LT
SOL
WHI/GRN
T4
WHI
T2
P2-2
RED
LEFT
BREW TIMER
T1 T5 T3 T4 WHI/GRN
RIGHT T2 WHI
P3-2
RED
BREW TIMER
SW7
BLK
RED
YEL
P4-2
YEL
RED P4-1
RED
WHI/YEL P4-3
WHI/YEL
RED
RIGHT TOP FRONT WARMER
MODEL 4/2 ONLY
SW9
BLK
RED
WHI/VIO
P5-3
WHI/VIO
RED
RED P5-1
RED
LEFT TOP REAR WARMER
SW10
BLK
RED
LEFT TOP FRONT WARMER
SW8
BLK
RED
RED
WHI/BRN P5-2 WHI/BRN
RED
RIGHT TOP REAR WARMER
200 OR 240 VOLTS AC 2 WIRE
SINGLE PHASE
10736.0002J 12/00 © 1993 BUNN-O-MATIC CORPORATION
Page 43
41711.1 052009
SCHEMATIC WIRING DIAGRAM
CWTFA 2/2 TWIN, CWTFA 4/2 TWIN & CWTFA TWIN-APS
GRN/YEL
LT. READY INDICATOR
BLK
SW1
BLK
BLK
BLK
BLU
LT. LIMIT
THERMOSTAT
L2
BLK
LT. SW. & THERMOSTAT
LEFT TANK HEATER
BLK
BLU
LEFT "KEEP WARM" HEATER
WHI
(FAUCET)
THERMAL
SAFETY FUSE
BLK
L1
RED
WHI
RT. READY INDICATOR
RIGHT TANK HEATER
BLK
BLK
RT. SW. & THERMOSTAT
BLU
BLK
BLK
BLK
RT. LIMIT
THERMOSTAT
SW2
BLU
RIGHT "KEEP WARM" HEATER
WHI
BLK
RED
RED
WHI
SW3
RED
NOT APPLICABLE TO APS MODELS
WHI/RED P1-2 WHI/RED
BLK
RED
LEFT LOWER WARMER
SW4
RED
WHI/GRN P1-3 WHI/GRN
BLK
RED P1-1
RED
RED
RIGHT LOWER WARMER
SW5
P3-3
WHI/GRN
BLK
T1 T5 T3
WHI/BLU
T1 T5 T3
YEL
P4-2
T4 WHI/GRN
WHI/YEL
P4-3
LT
SOL
WHI/GRN
T4
WHI
T2
P2-2 RED
LEFT
BREW TIMER
P3-2
RED
RED
YEL
RED
RED P4-1
LEFT TOP FRONT WARMER
SW8
BLK
RT
SOL
RIGHT T2 WHI
BREW TIMER
NOT APPLICABLE TO APS MODELS
SW7
WHI/BLU
BLK
BLU P3-1 BLU/BLK
WHI/GRN
BLK
BLU/BLK
P2-3
WHI/RED
SW6
P2-1
BLU
WHI/RED
WHI/YEL
RED
RED
RED
RIGHT TOP FRONT WARMER
MODEL 4/2 ONLY
SW9
BLK
RED
WHI/VIO
P5-3
RED
RED P5-1
LEFT TOP REAR WARMER
SW10
BLK
WHI/VIO
WHI/BRN
P5-2
WHI/BRN
RED
RED
RED
RIGHT TOP REAR WARMER
230 VOLTS AC 2 WIRE
SINGLE PHASE
10736.0004A 02/06 © 2006 BUNN-O-MATIC CORPORATION
Page 44
41711.1 052009
SCHEMATIC WIRING DIAGRAM
CWTFA TWIN-APS CE
L1
LT. READY INDICATOR
BLK
LT. SW. & THERMOSTAT
SW1
BLK
BLU
NC
BLK
BLU
RED
L2
GRN/YEL
LT. TANK HEATER
BLK
LT. LIMIT
THERMOSTAT
RED
RED
NC
BLK
WHI
LEFT "KEEP WARM" HEATER
WHI
LT. READY INDICATOR
BLK
LT. SW. & THERMOSTAT
SW2
BLK
BLU
NC
BLK
BLU
RED
RT. TANK HEATER
BLK
RT. LIMIT
THERMOSTAT
RED
RED
NC
BLK
WHI
RIGHT "KEEP WARM" HEATER
WHI
SW3
RED
SW5
BLK
WHI/RED
BLU
WHI/RED
WHI/BLU
WHI/RED
LT
SOL
T1 T5 T3 T4 WHI/GRN
LEFT
T2
RED
BREW TIMER
SW4
RED
SW6
BLK
WHI/RED
WHI/RED
BLU
WHI/BLU
WHI/RED
RT
SOL
T1 T5 T3 T4 WHI/GRN
RIGHT T2
RED
BREW TIMER
230 VOLTS AC
2 WIRE + GND
SINGLE PHASE
10736.0005B 08/07 © 2007 BUNN-O-MATIC CORPORATION
Page 45
41711.1 052009
L1
LT. READY INDICATOR
BLU
BLK
BLK
MAIN ON/OFF SWITCH
(Late Models only)
BLK
(FAUCET)
THERMAL
SAFETY FUSE
LT. SW. & THERMOSTAT
LT.LIMIT
THERMOSTAT
SW1
BLU
BLK
BLK
LEFT TANK HEATER
BLK
WHI
RED
BLK
WHI
LEFT "KEEP WARM" HEATER
BLK
RT. SW. & THERMOSTAT
RT. LIMIT
THERMOSTAT
BLK
RED
WHI
RT. READY INDICATOR
SW2
RED
BLK
GRN
N
L2
WHI
SCHEMATIC WIRING DIAGRAM CWTF TWIN 0/6
BLU
RIGHT TANK HEATER
BLK
WHI
RED
WHI
WHI
RIGHT "KEEP WARM" HEATER
RED
RED
SW3
WHI
P1-2 WHI/RED
WHI/RED
WHI/RED
SW4
WHI
P1-1
WHI
WHI
LEFT BREW WARMER
WHI
SW5
WHI/GRN P1-3 WHI/GRN
BLK
WHI
RIGHT BREW WARMER
SW7
BLK
SW6
WHI/ORA
P2-1
BLU
WHI/RED
SW8
P2-3 BLK
WHI/RED
BLU P3-1BLU/BLK
WHI/GRN
P3-3 BLK
WHI/GRN
BLU/BLK
WHI/BLU
WHI/ORA
WHI/BLU
LT
SOL
WHI
WHI/GRN
T1 T5 T3 T4
T2 WHI
LEFT
BREW TIMER
RT
SOL
P2-2
WHI/ORA
WHI/GRN
GRY
T1 T5 T3 T4
WHI
RIGHT T2
BREW TIMER
GRY
L.E.D.
L.E.D.
PIN
GRY
PIN PIN
WHI
P3-2
OPTIONAL INDICATOR
TIMER
WHI/ORA
WHI
WHI
BLK
SW9
SW10
BLK
WHI
WHI
BRN/BLK P5-3 BRN/BLK
BLK
WHI
P5-1
P4-1
RIGHT FRONT WARMER
P5-2
VIO
WHI
SW11
RED
YEL
WHI
WHI/VIO P4-3 WHI/VIO
WHI
SW12
RED
LEFT REAR WARMER
RIGHT REAR WARMER
120/240 VOLTS AC
3 WIRE + GND
SINGLE PHASE
YEL P4-2
WHI
LEFT FRONT WARMER
WHI
VIO
WHI
10741.0000H 01/07 © 1993 BUNN-O-MATIC CORPORATION
Page 46
41711.1 052009
MAIN ON/OFF SWITCH
(Late 20 & 35
Models only)
BLK-14
HEATER
SWITCH
BLK
LIMIT
THERMOSTAT
BLK
BLU
SW. & THERMOSTAT
(FAUCET OPTION ONLY)
THERMAL
FUSE
BLK
BLK
WHI Model 20
BLK Model 20 & 35
READY INDICATOR
BLU
BLK
N
L2
RED Model 35
WHI Model 20
WHI Model 15 & 35
GREEN
SCHEMATIC WIRING DIAGRAM C, CT & CWT
BLK Model 15
BLK
L1
WHI-14 Model 20
RED-14 Model 35
TANK HEATER
WHI Model 15
WHI
WHI
ON/OFF
SWITCH
"KEEP WARM" HEATER
WHI
3
BLK 2
1 WHI/RED
WHI/RED
WHI
LOWER WARMER
WHI/ORA
WHI/BLU
OPTIONAL AUTOMATIC BREW CIRCUIT
START SWITCH
OPTIONAL FRESH LIGHT SYSTEM (EARLY MODELS)
GRY
L.E.D.
PNK
4
INDICATOR 3
TIMER 2
1
WHI/RED
BLU
P3
WHI/RED
P1
L1
BLK
P1, P2, & P3 ARE PINS OF A
POLARIZED THREE-PIN
CONNECTOR.
N
SOL
BLU/BLK
WHI/BLU
T1 T5 T3
BREW T4
TIMER T2
WHI/GRN
WHI
P2
WHI
WHI
OPTIONAL DUAL WARMER ASSY (TOP OR SIDE)
WHI
3
1 BRN/BLK P2 BRN/BLK
BLK 2
FRONT
WHI P1 WHI
WHI
3
BLK 2
1
VIO
P3
VIO
REAR
OPTIONAL SINGLE TOP WARMER ASSY
120/240 VOLTS AC 3 WIRE
120 VOLTS AC 2 WIRE
SINGLE PHASE
WHI
3
BLK 2
1
VIO
P3
VIO
WHI
P1
WHI
REAR
10836.0000H 05/09 ©1995 BUNN-O-MATIC CORPORATION
Page 47
41711.1 052009
SCHEMATIC WIRING DIAGRAM CWTB
L1
BLU
HEATER
SWITCH
BLK
LIMIT
THERMOSTAT
BLK
L2
GRN/YEL
READY
BLK
SW. & THERMOSTAT
(FAUCET
OPTION ONLY)
THERMAL
FUSE
BLK
BLU
BLK
TANK HEATER
RED
ON/OFF SWITCH
RED
3
BLK 2
1 WHI/RED
WHI/RED
RED
LOWER WARMER
OPTIONAL AUTOMATIC BREW CIRCUIT
START SWITCH
BLU
WHI/RED
P1
BLU/BLK
P3
WHI/RED
BLK
P1, P2, & P3 ARE PINS OF A
POLARIZED THREE-PIN
CONNECTOR.
SOL
WHI/BLU
T1 T5 T3
BREW T4
TIMER T2
WHI/GRN
WHI
P2
RED
OPTIONAL DUAL WARMER ASSY (TOP OR SIDE)
RED
3
BLK 2
1 BRN/BLK P2 BRN/BLK
FRONT
RED P1 RED
RED
3
BLK 2
1
VIO
P3
VIO
REAR
OPTIONAL SINGLE TOP WARMER ASSY
RED
3
200 VOLTS AC 2 WIRE
SINGLE PHASE
BLK 2
1
VIO
P3
VIO
RED
P1
RED
REAR
10836.0002E 07/00 ©1995 BUNN-O-MATIC CORPORATION
Page 48
41711.1 052009
SCHEMATIC WIRING DIAGRAM CWTA
L1
BLU
HEATER
SWITCH
BLK
LIMIT
THERMOSTAT
ON/OFF
SWITCH
(FAUCET
OPTION ONLY)
THERMAL
FUSE
BLK
SW. & THERMOSTAT
BLK
BLU
BLK
L2
GRN/YEL
READY
TANK HEATER
BLK
RED
WHI
WHI
"KEEP WARM"
RED
3
BLK 2
1 WHI/RED
WHI/RED
RED
LOWER WARMER
OPTIONAL AUTOMATIC BREW CIRCUIT
START SWITCH
BLU
WHI/RED
P1
P3
WHI/RED
SOL
BLU/BLK
BLK
P1, P2, & P3 ARE PINS OF A
POLARIZED THREE-PIN
CONNECTOR.
WHI/BLU
T1 T5 T3
BREW T4
TIMER T2
WHI/GRN
WHI
P2
RED
OPTIONAL DUAL WARMER ASSY (TOP OR SIDE)
RED
3
BLK 2
1 BRN/BLK P2 BRN/BLK
FRONT
RED P1 RED
RED
3
BLK 2
1
VIO
P3
VIO
REAR
OPTIONAL SINGLE TOP WARMER ASSY
220-240 VOLTS AC
2 WIRE
SINGLE PHASE
RED
3
BLK 2
1
VIO
P3
VIO
RED
P1
RED
REAR
10836.0003E 07/00 ©1995 BUNN-O-MATIC CORPORATION
Page 49
41711.1 052009
SCHEMATIC WIRING DIAGRAM CWTA - CE
READY INDICATOR
BLU
BLK
L1
HEATER
SWITCH
LIMIT
THERMOSTAT
BLK
SW. & THERMOSTAT
GRN/YEL
L2
THERMAL
FUSE
BLK
BLK
BLU
THERMAL
FUSE
RED
RED
TANK HEATER
BLK
RED
"KEEP WARM" HEATER
WHI
WHI
BLK
RED
BLK
ON/OFF
SWITCH
LOWER WARMER
WHI/RED
WHI/RED
RED
SOL
OPTIONAL GRINDER INTERFACE
BATCH
SELECTION
SWITCH
1
2
3
BREW 4
TIMER 5
P1, P2, & P3 ARE PINS OF A
POLARIZED THREE-PIN
CONNECTOR.
WHI/RED
RED
WHI/ORN
WHI/GRN
WHI/YEL
START
SWITCH
OPTIONAL DUAL WARMER ASSY (TOP OR SIDE)
RED
4
GRY
3 GRINDER
INTERFACE
PNK
2 CONNECTOR
1
BLK
BRN/BLK
P2 BRN/BLK
FRONT WARMER
BLK
VIO
P3
RED P1
RED
RED
VIO
REAR WARMER
OPTIONAL SINGLE TOP WARMER ASSY
RED
230 VOLTS AC
2 WIRE
SINGLE PHASE
BLK
VIO
P3
VIO
RED
P1
RED
REAR WARMER
10836.0004H 10/02 ©1997 BUNN-O-MATIC CORPORATION
Page 50
41711.1 052009
20
AMP
T1
Page 51
T5 T3
T4
T2
41711.1 052009
GREEN
BLK Model 15
SCHEMATIC WIRING DIAGRAM
CWTF, CWTFB NO WARMER
MAIN ON/OFF SWITCH
(Late 20 & 35
Models only)
BLK-14
N
L2
RED Model 35
WHI Model 20
WHI Model 15 & 35
BLK
L1
BLK Model 20 & 35
BLU
HEATER
SWITCH
LIMIT
THERMOSTAT
BLK
BLK
BLK (FAUCET OPTION ONLY)
THERMAL
FUSE
SW. & THERMOSTAT
BLU
BLK
TANK HEATER
BLK
WHI-14 Model 20
RED-14 Model 35
WHI Model 15
WHI
WHI
ON/OFF
SWITCH
WHI Model 20
READY INDICATOR
"KEEP WARM" HEATER
WHI
WHI/RED
BLK
WHI/ORA
OPTIONAL FRESH LIGHT SYSTEM
OPTIONAL AUTOMATIC BREW CIRCUIT
START SWITCH
GRY
L.E.D.
PNK
4
INDICATOR 3
2
TIMER
BLK
120/240 VOLTS AC 3 WIRE
100-120 VOLTS AC 2 WIRE
SINGLE PHASE
1
WHI/RED
WHI/RED
BLU P1 BLU
P3
P1, P2, & P3 ARE PINS OF A
POLARIZED THREE-PIN
CONNECTOR.
BLK
BLK
BREW
TIMER
SOL
WHI
WHI
P2
WHI
WHI
10836.0006M 02/07 ©1995 BUNN-O-MATIC CORPORATION
Page 52
41711.1 052009
SCHEMATIC WIRING DIAGRAM
CWTFA NO WARMER
L1
READY INDICATOR
BLU
BLK
LIMIT
THERMOSTAT
BLK
BLU
HEATER
SWITCH
THERMAL
FUSE
BLK
BLK
SW. & THERMOSTAT
L2
GRN
TANK HEATER
THERMAL
FUSE
RED
RED
BLK
RED
BLK
WHI
WHI
ON/OFF
SWITCH
BLK
"KEEP WARM" HEATER
RED
WHI/RED
WHI/ORA
OPTIONAL AUTOMATIC BREW CIRCUIT
START SWITCH
OPTIONAL FRESH LIGHT SYSTEM
GRY
L.E.D.
PNK
BLK
4
WHI/RED
INDICATOR 3
2
TIMER
WHI/RED
BLU
P3
P1 BLU
BLK
BLK
SOL
1
P1, P2, & P3 ARE PINS OF A
POLARIZED THREE-PIN
CONNECTOR.
BREW
TIMER
WHI
WHI
P2 WHI
WHI
230 VOLTS AC
2 WIRE
SINGLE PHASE
10836.0008A 12/99 ©1999 BUNN-O-MATIC CORPORATION
Page 53
41711.1 052009
WHI
GRN
N
L2
RED
SCHEMATIC WIRING DIAGRAM
CT-DV, CTF-DV, CWT-DV & CWTF-DV
BLK
L1
MAIN ON/OFF SWITCH
(Late Models only)
BLK
READY INDICATOR
BLU
HEATER
SWITCH
LIMIT
THERMOSTAT
BLK
BLK
BLK
SW. & THERMOSTAT
(FAUCET OPTION ONLY)
THERMAL
SAFETY FUSE
BLK-14
BLU
BLK-14
SELECTOR
SWITCH
TANK HEATER
BLU-14
WHI-14
WHI
1320 W
WHI
"KEEP WARM" HEATER
ON/OFF
SWITCH
BLK
WHI/VIO-14
TANK HEATER
RED-14
1800 W
WHI
WHI/RED
WHI/RED
WHI
LOWER WARMER
OPTIONAL AUTOMATIC BREW CIRCUIT
START SWITCH
BLU
WHI/RED
WHI/BLU
WHI/RED
P1, P2, & P3 ARE PINS OF A
POLARIZED THREE PIN
CONNECTOR
T5 T3
T1 BREW
TIMER
T4
T2
SOL
WHI/GRN
WHI
OPTIONAL DUAL WARMER ASSY (TOP OR SIDE)
WHI
BLK
BRN/BLK
P2
BRN/BLK
FRONT WARMER
WHI
P1
WHI
WHI
VIO
BLK
P3
VIO
REAR WARMER
120V AC 2 WIRE
120/208V AC 3 WIRE
120/240V AC 3 WIRE
SINGLE PHASE
OPTIONAL SINGLE TOP WARMER ASSY
WHI
VIO
BLK
P3
VIO
WHI
P1
WHI
REAR WARMER
10836.0009C 02/07 ©2003 BUNN-O-MATIC CORPORATION
Page 54
41711.1 052009
WHI
GRN
SCHEMATIC WIRING DIAGRAM
CWT, CWTF - APS, TS, TC DV
N
L2
RED
BLK
L1
MAIN ON/OFF SWITCH
(Late Models only)
BLK
READY INDICATOR
BLU
HEATER
SWITCH
BLK
LIMIT
THERMOSTAT
BLK
BLK
SW. & THERMOSTAT
BLU
THERMAL
SAFETY FUSE
(Faucet models only)
BLK-14
BLK-14
SELECTOR
SWITCH
TANK HEATER
WHI/VIO-14
ON/OFF
SWITCH
WHI-14
BLU-14
TANK HEATER
RED-14
WHI
WHI
"KEEP WARM" HEATER
WHI
START SWITCH
BLK
WHI/RED
WHI/RED
WHI/RED
120V AC 2 WIRE
120/208V AC 3 WIRE
120/240V AC 3 WIRE
SINGLE PHASE
BLU
WHI/BLU
T5 T3
T1 BREW
TIMER
T4
T2
SOL
WHI/GRN
WHI
10836.0010B 02/07 ©2001 BUNN-O-MATIC CORPORATION
Page 55
41711.1 052009
SCHEMATIC WIRING DIAGRAM
SINGLE CW
L1
READY
HEATER
SWITCH
BLK
LIMIT
THERMOSTAT
BLK
(FAUCET
OPTION ONLY)
THERMAL
FUSE
BLK
BLK
N
GRN
SW. & THERMOSTAT
BLK
BLU
BLK
WHI (MODELS 15 & 20)
TANK HEATER
RED (MODEL 35)
WHI
WHI
ON/OFF
SWITCH
L2
"KEEP WARM" HEATER
WHI
3
BLK 2
1 WHI/RED
WHI/RED
WHI
LOWER WARMER
START SWITCH
SOL
BLU
WHI/RED
WHI/RED
WHI/BLU
PNK
TAN
T1 T5 T3
BREW T4
TIMER T2
WHI/GRN
WHI
HALF/FULL
SWITCH
WHI
3
BLK 2
120/240 VOLTS AC 3 WIRE
120 VOLTS AC 2 WIRE
SINGLE PHASE
1 BRN/BLK
P2
3
BLK 2
1
P1, P2, &
P3 ARE
PINS OF A
POLARIZED
THREE-PIN
CONNECTOR.
WHI
VIO
P3
P1
WHI
NO CONNECTION THIS APPLICATION
10836.0011B 01/03 ©2003 BUNN-O-MATIC CORPORATION
Page 56
41711.1 052009
L1
BLK
GRN
GRN
RIGHT
N
L2
RED
N
WHI
SCHEMATIC WIRING DIAGRAM
CWTF TWIN 4/2 & 0/6 TWO-CIRCUIT
WHI
RED
BLK
LEFT
L1 L2
READY INDICATOR
TANK HEATER
BLK
BLK
BLU
WHI
WHI
"KEEP WARM" HEATER
RED
READY INDICATOR
RED
SW. & THERMOSTAT
LIMIT
THERMOSTAT
SW1-R
BLK
BLU
BLK
TANK HEATER
BLK
"KEEP WARM" HEATER
WHI
RED
WHI
WHI
BLK
WHI
SW3-L
SW2-L
WHI/BLU
P1-3L BLK
WHI/RED
BLK
P1-1L BLU/BLK
BLU
WHI/RED
SOL
LEFT BREW WARMER
WHI/RED
WHI/GRN
T1 T5 T3
T4
T2 WHI
BREW TIMER
SW2-R
P1-2L
WHI
SW3-R
P1-1R BLU/BLK
BLU
WHI/RED
P1-3R
WHI/RED
BLK
WHI/BLU
WHI/RED RIGHT BREW WARMER
SOL
WHI/GRN
T4
T2 WHI
BREW TIMER
T1 T5 T3
P1-2R
WHI
BLK
WHI
SW4-L
WHI
BLK
SW4-R
WHI
WHI
WHI
P2-1L
P2-2L
BLK
SW5-L
BLK
LEFT FRONT WARMER
WHI
VIO
BLK
BRN/BLK
P2-3L
VIO
BRN/BLK
SW5-R
WHI
BLK
BLK
BLK
MAIN ON/OFF SWITCH
(Late Models only)
(FAUCET SIDE)
THERMAL
SAFETY FUSE
SW. & THERMOSTAT
LIMIT
THERMOSTAT
SW1-L
BLK
BLK
RED
MAIN ON/OFF SWITCH
(Late Models only)
BLK
P2-2R
P2-1R
BRN/BLK
WHI
VIO
WHI
RIGHT FRONT WARMER
P2-3R
VIO
WHI
RIGHT REAR WARMER
LEFT REAR WARMER
TWO INDIVIDUAL BRANCH
CIRCUITS REQUIRED
EACH RATED
120/240 VOLTS AC
3 WIRE + GND
SINGLE PHASE
10847.0000D 01/07 ©1994 BUNN-O-MATIC CORPORATION
Page 57
41711.1 052009
GRN
BLK
BLK
BLU
BLU
K1 N.O.
RT. SW. & THERMOSTAT
RT. LIMIT
THERMOSTAT
BLK
RED
BLK
WHI
SW2
BLK
LEFT TANK HEATER
BLK
BLU
MAIN ON/OFF SWITCH
(Late Models only)
(FAUCET)
THERMAL
FUSE
LT. SW. & THERMOSTAT
LT. LIMIT
THERMOSTAT
SW1
BLK
BLU
WHI
LEFT "KEEP WARM" HEATER
BLU
BLK
BLU
N
L2
WHI
BLK
L1
RED
SCHEMATIC WIRING DIAGRAM CWT TWIN 2/2 & 4/2
W/RECOVERY BOOSTER
BLK
RIGHT TANK HEATER
RED
BLK
K2 N.O.
WHI
WHI
RIGHT "KEEP WARM" HEATER
RED
SW3
WHI
WHI/RED P1-2 WHI/RED
RED
WHI P1-1
WHI
WHI
LEFT LOWER WARMER
SW4
WHI
WHI/GRN P1-3 WHI/GRN
BLK
WHI
RIGHT LOWER WARMER
SW5
BLK
P2-1
BLU
WHI/RED
P2-3
WHI/RED
SW6
BLK
K2
P3-1
WHI/GRN
BLU
WHI/GRN
P3-3
WHI
BLU/BLK
BLK
BLK
RT
SOL
WHI
WHI/BLU
T1 T5 T3 T4 WHI/GRN
WHI
RIGHT T2
K1
WHI
BLU/BLK
BLK
BLK
LT
SOL
WHI/BLU
T1 T5 T3
WHI/GRN
T4
WHI
LEFT T2
WHI
P2-2
WHI
BREW TIMER
P3-2
WHI
BREW TIMER
MODELS 2/2 & 4/2 ONLY
RED
SW7
WHI
RED
YEL
P4-2
YEL
SW8
WHI P4-1
WHI
WHI
WHI/YEL P4-3
BLK
WHI
LEFT TOP WARMER
WHI
WHI/YEL
RIGHT TOP WARMER
MODELS 4/2 ONLY
RED
SW9
WHI
WHI/VIO P5-3 WHI/VIO
RED
WHI P5-1
WHI
LEFT TOP WARMER
SW10
BLK
WHI
WHI
WHI/BRN P5-2 WHI/BRN
WHI
RIGHT TOP WARMER
120/240 VOLTS AC
3 WIRE + GND
SINGLE PHASE
10867.0000F 01/07 © 1995 BUNN-O-MATIC CORPORATION
Page 58
41711.1 052009
SCHEMATIC WIRING DIAGRAM CWTF TWIN 0/6 WITH
RECOVERY BOOSTER
L1
BLK
BLK
BLU
LT. SW. & THERMOSTAT
BLU
BLK
BLU
WHI
L2
BLK
BLK
BLU
LT.LIMIT
THERMOSTAT
SW1
N
GREEN
LT. READY INDICATOR
RED
(FAUCET)
THERMAL
SAFETY FUSE
BLK
BLK LEFT TANK HEATER
RED
BLK
K.1. N.O.
WHI
BLK
RT. LIMIT
THERMOSTAT
BLK
BLU
BLU
SW2
RT. SW. & THERMOSTAT
BLK
RT. READY INDICATOR
LEFT "KEEP WARM" HEATER
RED
BLK
BLU
BLK
BLU
RIGHT TANK HEATER
BLK
RED
BLK
K.2. N.O.
WHI
WHI
RIGHT "KEEP WARM" HEATER
RED
SW3
WHI
RED
P1-2 WHI/RED
WHI/RED
WHI/RED
SW4
WHI
WHI
LEFT BREW WARMER
P1-1
WHI
WHI
SW5
WHI/GRN
BLK
P1-3 WHI/GRN
SW7
WHI
RIGHT BREW WARMER
BLK
SW8
WHI/GRN
P3-1
BLU BLU/BLK
WHI/GRN
P3-3 BLK
GRY
GRY
BLK
SW6
K2
WHI
P2-1
BLU BLU/BLK
BLK
BLK
WHI/RED
WHI/RED
P2-3
WHI/ORA
RT
WHI
SOL
WHI/BLU WHI/GRN
T1 T5 T3
T4
RIGHT
T2 WHI
BREW TIMER
BLK
K1
WHI
BLK
WHI/ORA
LT WHI
SOL
WHI/BLU
WHI/GRN
T1 T5 T3
T4
LEFT
T2 WHI
BREW TIMER
PNK GRY
PNK
PNK
P2-2 WHI
WHI/ORA
WHI
P3-2
4
L.E.D.
L.E.D.
WHI
WHI/ORA
WHI
OPTIONAL 3
INDICATOR 2
TIMER
1
WHI
BLK
SW9
BLK
BRN/BLK
SW10
BLK
WHI
WHI
P5-2 BRN/BLK
WHI
P5-1
P4-1
WHI
RIGHT FRONT WARMER
YEL
YEL
LEFT FRONT WARMER
WHI
VIO
P4-2
WHI
P5-3
VIO
120/240 VOLTS AC 3 WIRE
SINGLE PHASE
WHI
RIGHT REAR WARMER
WHI
SW11
WHI/VIO P4-3 WHI/VIO
LEFT REAR WARMER
RED
SW12
RED
27693.0000D 07/03 © 1996 BUNN-O-MATIC CORPORATION
Page 59
41711.1 052009