Automatic Technology Australia GDO-2 SecuraLift Troubleshooting guide

GDO-11v1 SecuraLift®
Overhead Garage Door Opener
Featuring TrioCode™ Technology
Part # 13246 (Manual v1.02)
WARNING: It is vital for the safety of persons to follow
all instructions. Failure to comply with the installation
instructions and the safety warnings may result in serious
personal injury and/or property damage.
Please save these instructions for future reference.
Automatic Technology (Australia) Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all
conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of an
Automatic Technology (Australia) Pty Ltd Garage Door Opener. Automatic Technology (Australia) Pty Ltd hereby further
expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person
as a result whether directly or indirectly from failure to install the Automatic Technology (Australia) Pty Ltd Garage Door
Opener in accordance with these installation instructions.
2
GDO-11v1 SecuraLift® Owner Installation Instructions
GDO-11v1 SecuraLift®
Overhead Garage Door Opener
Important Safety Instructions
4
Features
6
Operating Controls
8
Kit Contents
10
Installation
11
Knockdown C-Rail Assembly
11
C-Rail Attachment
13
Determine Door Type
14
Mounting - Track Type Door
15
Photo Electric Beam Installation
25
Mounting - Spring Loaded Door
16
Key switch
25
Mounting Door Bracket & Arms
17
Auxiliary output
25
18
Battery Back Up installation
26
SmartSolar™ Installation
27
Programming the Opener
Setting Travel Limits - Control Panel 18
Setting Travel Limits - Transmitter
Safety Obstruction Forces
Safety Obstruction Force Test
19
Final Set Up
25
28
20
Pet Mode Door Height
28
20
Wall Mounted Transmitters
28
Re-Initialising
28
Default Settings & Specifications
29
Adjusting Safety Obstruction Forces 21
Coding Transmitters
Accessories
22
Parameters
30
Door
22
Vacation Mode
22
Door Status Indicators
30
Auxiliary Out Put
22
Button functions
30
Pet Mode
23
Troubleshooting Guide
31
Courtesy Light
23
Maintenance Record
32
Remotely Coding Transmitters
24
Parts Listing
33
Erasing Transmitter Codes
24
Warranty
34
Owner Installation Instructions GDO-11v1 SecuraLift®
3
Important Safety Instructions
WARNING: It is vital for the safety of persons to follow
all instructions. Failure to comply with the following
Safety Rules may result in serious personal injury and/or
property damage.
CAUTION: If your garage has no pedestrian entrance door, an emergency access device should be installed.
This accessory allows manual operation of the garage door from outside in case of power failure.
For ADDITIONAL ENTRAPMENT protection we STRONGLY recommend the fitting of a Photo Electric
(P.E.) Beam. In most countries P.E. Beams are mandatory on all garage doors fitted with automatic
openers. For a small additional outlay Automatic Technology recommends that Photo Electric Beams
be installed with the automatic opener ensuring additional safety and peace of mind.
DO NOT operate the opener unless the garage door is in full view and free from objects such
as cars and children/people. Make sure that the door has finished moving before entering or
leaving the garage.
DO NOT operate the opener when children/persons are near the door. Children must be
supervised at all times when the SecuraLift® is in use. Serious personal injury and/or
property damage can result from failure to follow this warning.
DO NOT allow children to operate the SecuraLift®. Serious personal injury and/or
property damage can result from failure to follow this warning.
Regularly check to make sure that the safety obstruction force is working
correctly, and is tested and set as per page 20 of this manual. Failure to
follow these instructions could result in serious personal injury and/or
property damage. This test must be repeated at regular intervals and the
necessary adjustments made as required.
Doors requiring over 400N of force to move must have P.E. Beams
installed.
DO NOT disengage the door opener to manual operation with
children/persons or any other objects including motor vehicles
within the doorway.
The door opener is not intended for use by young children
or infirm persons without adequate supervision. Children
should be supervised to ensure that they do not play
with the remote transmitters or the opener.
Keep hands and loose clothing clear of the door
and door opener at all times.
4
GDO-11v1 SecuraLift® Owner Installation Instructions
Important Safety Instructions
The unit should be installed so that it is protected from the elements. It should not be exposed to water or rain.
It is not to be immersed in water or sprayed directly by a hose or other device.
The garage door must be well balanced. Sticking or binding doors must be repaired by a qualified garage
door installer prior to installation of the opener.
Frequently examine the installation, in particular cables, springs and mountings for signs of wear, damage
or imbalance. DO NOT use if repair or adjustment is needed since a fault in the installation or an
incorrectly balanced door may cause injury. DO NOT attempt to repair the door yourself as hardware
is under extreme tension.
Remove or disengage all garage door locks and mechanisms prior to installation of the opener.
Connect the opener to a properly earthed general purpose 240V mains power outlet installed
by a qualified electrical contractor.
Disconnect the power cord from mains power before making any repairs or removing
covers. Only experienced service personnel should remove covers from the opener.
In order for the SecuraLift® to sense an object obstructing the door way, some force
must be exerted on the object. As a result the object, door and/or person may
suffer damage or injury.
If the power supply cord is damaged, it must be replaced by an Automatic
Technology service agent or suitably qualified person.
Make sure that the door is fully open before driving in or out of the garage
and fully closed before leaving the driveway.
Make sure that remote controls are kept out of reach of children.
Install the (optional) wall switch or (optional) wall mounted
transmitter in a location where the garage door is visible, but
out of the reach of children at a height of at least 1.8 meters
from the floor.
Owner Installation Instructions GDO-11v1 SecuraLift®
5
Features
Thank you for purchasing the Automatic Technology
GDO-11v1 SecuraLift® Overhead Garage Door
Opener. Designed to suit sectional overhead and one
piece tilt up doors, the components and materials
used ensure this opener will provide years of
smart, simple and secure operation. Listed
below are some of the many features:
Operation
To open or close the door simply press a button on a TrioCode™ handheld
transmitter, or optional wall switch for two seconds. During open and close cycles
the door can be stopped by pressing the button again. The next actuation will
move the door in reverse direction.
TrioCode™ Code Hopping Technology
Every time a TrioCode™ transmitter is used a new security code is randomly
generated from over 4.29 billion possibilities. This greatly enhances the security
of the system and makes “code grabbing” a thing of the past
These transmitters also overcome interference issues by simultaneously sending a
signal over three different frequencies. Even if two of the three signals are jammed,
the system will still work.
S-ALPS (Semi Automatic Limits Positioning System)
The S-ALPS system does away with manual adjustment of the door’s limits position
using mechanical parts, such as cams and microswitches. During installation the
handheld transmitter can be programmed to set the limits positions.
ISS (intelligent safety obstruction system)
While the door is performing a close cycle, should it hit an obstacle or be restricted in some
manner, it will automatically reverse. The amount of force the door should encounter before
reversing is automatically adjusted by the doors control system during the initial installation of the
automatic door opener. The door will also stop if restricted whilst opening. The Safety Obstruction
Force should be checked monthly.
Auto courtesy light
The courtesy light comes on automatically for three minutes whenever the door is activated. The light can also
be operated independently of the door by coding a dedicated button on a transmitter.
6
GDO-11v1 SecuraLift® Owner Installation Instructions
SmartSolar™ and Battery Back Up Compatibility (optional)
The opener can be fitted with a SmartSolar™ or Battery Back Up kit for operation in the
event of a power outage, or where mains power access is not available.
NOTE: If the door is the only entrance to the garage, and a battery back up kit is
not fitted, a keyed cable release should be fitted external to the garage.
Vacation mode
A hand held transmitter can be programmed to lock and unlock all other
transmitters that have been programmed into the openers’ memory. The vacation
mode can be used when the door is left idle for long periods of time.
Pet/Pedestrian mode
The transmitter can be programmed to open the door to an adjustable partial
height so that the family pet can enter and exit the garage at any time. You may also
wish to open the door to a height suitable only for pedestrian access.
Photo Electric (P.E.) Beam (optional)
The opener has an input to connect a P.E. Beam for extra safety.
Manual operation
The opener is equipped with a unique manual disengaging device. If the power to the opener
is disrupted the door can be put into manual mode by pulling down on the string handle on an
angle towards the door. This allows for manual operation of the door. To re-engage the opener pull
the string handle away from the door.
Owner Installation Instructions GDO-11v1 SecuraLift®
7
Operating controls
01
Terminal Block.
»
»
»
»
»
»
02
CODING LED (red) light flashes when a code is being stored or when a transmitter button is pressed.
03
DOOR CODE BUTTON is used for storing or erasing transmitter buttons for door operation
04
DOOR STATUS LED (Yellow)
05
SET button (Orange) is used during the installation phase together with the Open and MINUS (-) buttons
to set the door limit positions. The Set button is also used to re-initialize the Opener.
06
OPERATE button (Yellow) is used during installation to test the open, stop and close cycles for the
07
08
09
10
opener. The opener has to be initialised by the set button to make the OPERATE button operable.
FORCE MARGIN SET Button: The obstruction force margin is set automatically during installation. The
margin can be adjusted manually using the Force Margin Set button (White). Holding the Force Margin Set
button and pressing PLUS (+) or MINUS (-) buttons will increase or decrease the amount of force. The Force
Margin Set should only be used if environmental factors (wind, etc.) affect the door’s operation.
OPEN LIMIT LED (green) the LED is very helpful during installation. It illuminates and flashes when the
door is opening and remains steady on when the open limit position has been reached.
PLUS (+) button (green) is used during installation to help set the open limit position. Pressing and holding
this button will move the door in the open direction, releasing stops the door.
NOTE: The safety obstruction detection is inoperable when the PLUS (+) button is used to move door.
CLOSE LIMIT LED (red) the LED is very helpful during installation. It illuminates and flashes when the
door is closing and remains steady on when the close limit position has been reached.
11
MINUS (-) button (red) is used during installation to help set the close limit position. Pressing and holding
12
DATUM ADJUST SCREW is used during limits set up to indicate the mid point of the door’s travel.
13
10A FUSE
14
8
24V PWR is used to power photo electric beam.
PE (Input) for photo electric beam for safety.
PE (0v) is used to supply 0 volts to photo electric beam.
GND is used with OSC input or AUX out put
O/S/C INPUT is used for the connection of a wired switch (momentary contact). This switch
can then be used to open, stop or close the door. Install the wall switch in a location where
the switch is out of reach of children and the garage door is visible.
AUX (output) can be used to control alarm system .
this button will move the door in the close direction. Movement stops when the button is released.
NOTE: The safety obstruction detection is inoperable when the CLOSE button is used to move door..
PROG INPUT is used to connect the Automatic Technology Handheld Programmer “PG-3” for editing
control and receiver functions, accessing diagnostic tools, and activating special features and operating
modes.
15
JP1 SOLAR CONNECTOR onto this the shunt must be fitted for solar operation.
16
COURTESY LIGHT 15 watts 24 volts feston type globe is used for courtesy light
GDO-11v1 SecuraLift® Owner Installation Instructions
12
fig 01
02
01
03
04
05
06
07
08
09
10
11
16
15
14
13
Owner Installation Instructions GDO-11v1 SecuraLift®
9
Kit contents
GDO-11v1 Multipiece C Rail And Accessory
1 x GDO-11v1 SecuraLift® Ero drive unit (Fig. 02)
1 x TrioCode™ Transmitter pack (Fig. 02)
(Pack includes 1x four button keyring transmitter and
1x two button keyring transmitter with batteries)
2 x Door attachment arms (Fig. 02)
1 x Accessory and hardware pack (Fig. 02)
1 x Chain (Fig. 02)
1 x C rail track pack (Fig. 02)
(Pack includes three C rail sleeves and four C rail tracks)
1 x Shuttle assembly (Fig. 02)
1 x Installation Manual
fig 02
OR
Power Head And Accessory pack
1 x GDO-11v1 SecuraLift® Ero drive unit (Fig. 03)
1 x TrioCode™ Transmitter pack (Fig. 03)
(Pack includes 1x four button keyring transmitter and
1x two button keyring transmitter with batteries)
2 x Door attachment arms (Fig. 03)
1 x Accessory and hardware pack (Fig. 03)
1 x Chain (Fig. 03)
1 x Shuttle assembly (Fig. 03)
1 x Installation Manual
fig 03
PLUS
Pre-Assembled Single Piece C-Rail
Note: The chain or belt in the single piece rail has been
tensioned by the factory.
fig 04
10
IMPORTANT NOTE: If modification to the track length
is required, adjustment must be made to the drive end
side only.
GDO-11v1 SecuraLift® Owner Installation Instructions
Knockdown C-Rail Assembly
Step 1 - Knockdown C-Rail Assembly
Note: If your opener came with a one piece track,
proceed to Assembly step 2, page 13.
a.
b.
c.
d.
e.
f.
Tr
ac
k
Place track pieces on flat surface for assembly. All
the track sections are interchangeable.
Slide sleeve onto the track section (Fig. 05). Connect
track by sliding sleeve onto next track section. Tap
track assembly on piece of wood until track sections
are flush. Repeat with remaining track sections.
Remove chain from package and lay chain out on
floor (do not allow chain to twist).
Loop the chain onto the pulley of tension chain
assembly. Slide the tension chain assembly with
chain into the track (Fig. 06).
Slide shuttle assembly into (opener end) the track
assembly, be sure to insert shuttle assembly with
hole side toward the door as shown with arrow in
(Fig. 07). Push the sprocket support into (opener
end) of the track.
Feed the chain through the shuttle assembly then
through the sprocket support and loop around
the sprocket then feed back through the sprocket
support and shuttle assembly. Join to chain index
with chain links ( supplied ) (Fig. 07).
fig 05
Sle
ev
e
Te
ns
ion
as
se
mb
ly
Do
or
en
d
Op
en
er
en
d
fig 06
Ch
ain
Idler pulley
Shuttle with hole side toward the door
fig 07
Ho
le
Owner Installation Instructions GDO-11v1 SecuraLift®
11
Knockdown C-Rail Assembly
Do
or
en
d
Note: Use the 12 teeth sprocket with Gdo-11v1 opener.
Op
en
er
h.
en
d
i.
fig 08
12
te
et
hs
pr
oc
ke
t
j.
k.
9 teeth sprocket
fig 09
Tension hex bolt
Do
or
en
d
Op
en
er
en
d
fig 10
Centre of the track
12
GDO-11v1 SecuraLift® Owner Installation Instructions
Engage the shuttle with the chain index and move
shuttle assembly to the centre of track. Make sure
the chain is engaged into the sprocket and also
wrapped around the centre of the pulley.
Use a spring scale to measure required force to pull
the shuttle, adjust 1/2” tension hex bolt (Fig. 09) to
tension the chain.
Move the shuttle back to the centre of the track to
re-test the force with spring scale (Fig. 10).
Continue to adjust adjust the tension hex bolt until a
force of 8kg to 8.5 Kg is achieved.
C-Rail Attachment
Step 2 - Secure C-Rail to Drive Unit
a.
b.
Shaft
Locate and insert the shaft of drive unit into the CRail’s sprocket (Fig. 11).
Fix the two track brackets with four screws supplied
in accessory pack (Fig. 12).
fig 11
Locate shaft into sprocket
Mushroom Head Screw Taptite ‘S’ M4 x 8
Track bracket (x2)
fig 12
Owner Installation Instructions GDO-11v1 SecuraLift®
13
Determine the Door Type
Step 3 - Determine Door Type
Determine which type of garage door you have as
illustrated below. (Fig. 13 to 15).
For a sectional (panel) door on tracks (Fig. 13)
proceed with the installation from Step 4.
Track
fig 13
Door
Sectional door with track
For a one-piece door on tracks (Fig. 14)
proceed with the installation from Step 4.
fig 14
One piece door with
track
For a one-piece door without tracks (on springs) (Fig. 15)
proceed with the installation from Step 8.
Door
fig 15
One piece door
without track
14
GDO-11v1 SecuraLift® Owner Installation Instructions
Mounting on a Track Type Door
WARNING: The opener must be securely
fastened to structural supports, otherwise opener
failure may ensue causing serious personal injury
and/or property damage.
Level
Level
Track
fig 16
Step 4 - Determine Bracket Position
a.
b.
c.
Open the door and find the highest point of travel of
the top door panel.
Using a level, transfer this height to the wall above
the door (Fig. 16) and mark a line 60mm above it.
Determine the centre point on the wall above and on
top of the door. Draw two lines extending 21.5mm
from each side of the centre point. (Fig. 17)
Door
Step 5 - Mounting the Wall Bracket
a.
b.
c.
Centre the bracket over the intersection of these two
lines. Mark centres for at least two holes (Fig. 17).
•
Ensure this is into a solid mounting point
Drill holes into the wall with an appropriate bit.
Secure to the wall using:
IF CONCRETE OR BRICK - 8mm (5/6”) loxins/dynabolts.
IF TIMBER - wood screw #20 or similar (min. 50mm).
3
4 .5
1
52
21.
fig 17
WARNING: Make sure concrete, brick wall or
timber lintels are solid and sound so as to form a
secure mounting platform.
Drilled holes
Step 6 - Attach the Rail to the Wall Bracket
a.
b.
Attach the C-Rail assembly to the wall bracket
with the 90mm long clevis pin and secure with the
supplied snap pin (Fig. 18)
Leave the powerhead in its packing box for protection
during installation.
fig 18
Step 7 - Secure the Powerhead to the Ceiling
a.
b.
c.
d.
e.
Raise the powerhead from the packing box and
support it in the horizontal position with a step
ladder or with a similar rigid object.
Open the garage door. Rest the opener on the open
door and use a scrap piece of wood to bring it to
horizontal level.
Line up the track perpendicular to the wall.
Secure the perforated angle (not supplied) to
the ceiling above where powerhead’s mounting
holes will be once fully installed. A representative
mounting is shown (Fig. 19)
Connect the powerhead to the ceiling mounted
perforated angle with M8x20mm screws and nuts.
Strips should not extend more than 18mm below
centre of powerhead mounting holes.
Structural member
fig 19
Go to Step 12 on page 17.
Owner Installation Instructions GDO-11v1 SecuraLift®
15
Mounting on a non-Track Type Door
WARNING: The opener must be securely fastened to
structural supports, otherwise opener failure may ensue
causing serious personal injury and/or property damage.
Centre of Door
Step 8 - Determine the Door’s Centre
a.
fig 20
b.
Find the centre of the door and mark this location
both above the door and on top of the door.
Draw two lines 21.5mm either side of this (Fig. 20).
Step 9 - Prepositioning the Opener
a.
b.
c.
Raise the door to open position.
Rest the opener on the top edge of the door with
end of the rail against the wall (Fig. 21).
Support the powerhead level with the lowest point
of the open door (Fig. 21).
NOTE: Do not slide rail along the face of the door.
Step 10 - Mounting the C-Rail
a.
fig 21
Step
ladder
b.
c.
d.
e.
C rail
f.
g.
fig 22
Highest point
of door travel
Door
Step
ladder
h.
Close the door slowly. The rail will be elevated by
the top edge of the door as it moves.
Stop the door when it is at its highest point of travel.
Allow 25mm additional height for clearance between
the door and the track (Fig. 22).
Support the Rail in this position and close the door
The height determined in Step 10 (b) will be the
height at which to mount the wall bracket.
Centre the bracket along the line determined in Step
8
Using the bracket as a template, mark a minimum of
two holes and drill with appropriate size bit. For a
more secure fitting, the wall bracket can be anchored
using more than two holes.
Secure the bracket to the wall using:
IF CONCRETE OR BRICK - 8mm (5/6”) loxins/dynabolts.
IF TIMBER - wood screw #20 or similar (min. 50mm)
Attach the bracket and C-Rail with supplied pins (Fig. 18).
WARNING: Make sure concrete, brick wall or
timber lintels are solid and sound so as to form a
secure mounting platform.
Step 11 - Secure the Powerhead to the Ceiling
Drill hole at centre of
track (recommended
bolt size M6 or M8)
a.
b.
fig 23
Ceiling
Steel Rail
Shuttle Assembly
16
GDO-11v1 SecuraLift® Owner Installation Instructions
Secure the perforated angle (not supplied) to the
ceiling above where powerhead’s mounting holes
will be. See (Fig.19) for a representative mounting.
Connect the powerhead to the ceiling mounted
perforated angle with M8x20mm screws and nuts.
Strips should not extend more than 18mm below
centre of powerhead mounting holes (Fig. 19).
Step 11.1 - Alternative Mounting Option
The opener can be fastened to the roof by driving a bolt
through the C-Rail into a structural timber support. The
bolt head’s height must not exceed 6mm (Fig. 23).
Mounting Door Bracket & Arms
Step 12 - Mounting Door Bracket
The door bracket comes in two parts. The bottom plate
with two mounting holes is used on its own for one piece
doors. For sectional doors, the top plate is placed over
the bottom plate and is fixed with four (4) screws (Fig.
24).
a.
b.
fig 24
Mount the door bracket, or bracket assembly,
on the door’s centre line one-third down the top
panel (Fig. 24) using M6 or equivalent screws (not
supplied),
STEEL DOORS ONLY: Bracket can be welded in
place.
NOTE: If in doubt about the door’s strength,
reinforcement may be added to the door’s frame
where necessary. Door damage may occur if the
bracket is installed on a panel with insufficient
strength. The opener’s warranty does not cover
damage caused to the door and/or door panels.
Straight arm
connected to the
shuttle
fig 25
Step 13 - Attaching the Arms
FOR SECTIONAL AND ONE PIECE DOORS WITH
TRACK:
the
bent
arm(connecting
to
a. Assemble
the door) to the right side of the straight
arm (connecting to the shuttle) with bolts
and nuts supplied in the accessory pack (Fig. 25).
Always use both bent and straight arms.
b. Connect the assembled arm to the bracket and the
disengaged trolley with clevis and snap pins. The
angle “A” must be more than 10° (Fig. 26).
WARNING: Connecting the bent arm other way
around may damage the door. The straight arm
should not protrude beyond heal of bent arm
Bent arm onnected
to the door
Centre of the door
0
10
A
fig 26
FOR ONE PIECE DOORS WITHOUT TRACK
a. Assemble the bent and straight arms as shown
in (Fig. 27) with bolts and nuts supplied in the
accessory pack. Always use both the bent and
straight arms.
b. Connect the assembled arm to the bracket and the
disengaged trolley with clevis and snap pins.
c. If installing on a door with a bad wave action,
lengthening the arm will assist in reducing this
effect.
IMPORTANT NOTE: Adjust the length of the
cord so that its toggle is no more than 1.8m from
the ground.
fig 27
Owner Installation Instructions GDO-11v1 SecuraLift®
17
Setting Limits
NOTE: If P.E. Beams are to be used they must be
installed before setting the travel limits.
Step 14.1 - Remove Controls Cover
a.
Swing open the controls cover to gain the access to
the controls panel (Fig. 28) and swing back into its
position when setup is completed.
fig 28
Step 14.2 - Connect Power to the Powerhead
Plug the power cord into a mains point and switch power
on. The red CLOSE LIMIT LED will be flashing.
WARNING: The safety obstruction detection
system is inoperable while MINUS (-) and PLUS (+)
drive buttons are being used and travel limits are
not set.
Step 14.3 - Set the Datum Position
a.
b.
fig 29
Press and hold the MINUS (-) or PLUS (+) buttons to
move the door to the halfway position. Ensure that
the door, shuttle and chain index are engaged.
Using a small screwdriver, turn the DATUM ADJUST
screw until the STATUS LED comes on (Fig 29).
» If the STATUS LED is already illuminated when
the door is halfway up, turn the DATUM ADJUST
screw until the light goes off, then turn back one
notch to illuminate again.
Step 14.4 - Set the Limits Positions
a.
b.
c.
Press and hold the MINUS (-) button until the door
reaches the desired close limit position. Single
presses will inch the door closed (Fig 30)..
Press the LIMIT SET button to store the close position
into memory (Fig. 30)
Press and hold the PLUS (+) button until the door
reaches the desired open limit position. Single
presses will the inch the door open (Fig. 30).
IMPORTANT
WARNING: The door will
automatically close, open and close again once
Step 14.4(d) is performed. Ensure that no persons
or objects are in the door’s path.
a.
d.
Press the SET button to store the close position into
memory (Fig. 30).
The door will now automatically close and open to
calculate the safety obstruction settings. After this, the
opener can be operated with the OPERATE button.
fig 30
Step 14.5 - Resetting the Door Limit Positions
Limit positions can be deleted by the following steps:
a. Press and hold the MINUS (-) button for six (6)
seconds until you hear three beeps and the CLOSE
LIMIT LED starts to flash.
b. Release the CLOSE button.
c. Repeat Steps 14.1 to 14.4 to set new travel limit
positions..
18
GDO-11v1 SecuraLift® Owner Installation Instructions
Setting Limits: via Transmitter
The GDO-11v1 has the unique ability to set travel
limits using the transmitter, allowing the installer to
move around the garage and door to better assess the
desired close and open limit positions.
Step 15.1 - Power Up and Set the Datum
a.
Follow Steps 14.1 to 14.3 as outlined overleaf.
Observe all warnings!
fig 31
Step 15.2 - Code a Transmitter for Limit Setting
a.
b.
c.
Press and hold the DOOR CODE button (Fig. 31).
Press Button 1 on the transmitter for two seconds
(Fig. 32). Release and pause for two seconds. Press
the same button again on the transmitter for two
seconds.
Release the DOOR CODE button.
Step 15.3 - Setting Limits via Transmitter
a.
b.
c.
d.
e.
Press and hold Button 4 on the transmitter to close
the door. When the door is approx. 2 cm from the
ground, release button 4.
A brief press of Button 4 will allow you to “inch” the
door closed. Keep doing this until the door reaches
the desired close limit position.
»
If the door is closed too far, press Button 1
to “inch” the door towards open
When happy with the close limit position, press
Button 2 to store this in memory.
Press Button 1 to open the door. When approx. 2
cm from the desired open position, release button
1.
A brief press of Button 1 will allow you to “inch” the
door open. Keep doing this until the door reaches
the desired open limit position.
»
If the door is opened too far, press Button
4 to “inch” the door towards close.
Button 1
(Inch Open)
Button 4
(Inch Close)
Button 2
(Set)
fig 32
IMPORTANT
WARNING: The door will
automatically close, open and close again once
Step 15.3 (f) is performed. Ensure that no persons
or objects are in the door’s path.
f.
g.
When happy with the open limit position, press
Button 2 on the transmitter to store into memory.
The door will now automatically close ,open and close
to calculate the safety obstruction settings. After
this, the opener can be operated with the OPERATE
button.
Step 15.4 - Resetting the Door Limit Positions
Limit positions can be deleted by the following steps:
a. Follow Steps 14.5 (a) and (b), as outlined overleaf.
b. Repeat Steps 15.1 and 15.3 to set new travel limit
positions.
»
There is no need to re-code the transmitter
(Step 15.2) upon resetting travel limits. The
transmitter will still be stored in memory.
Owner Installation Instructions GDO-11v1 SecuraLift®
19
Safety Obstruction Force Test
WARNING! Take care when testing or adjusting
the Safety Obstruction Force. Excessive force
may cause SERIOUS PERSONAL INJURY and/or
PROPERTY DAMAGE
WARNING! FOR ADDITIONAL ENTRAPMENT
protection we STRONGLY recommend the
fitting of a Photo Electric (P.E.) Beam. In most
countries P.E. Beams are mandatory on all
garage doors fitted with automatic openers. For
a small additional outlay Automatic Technology
recommends that Photo Electric Beams be
installed with the automatic opener ensuring
additional safety and peace of mind.
fig 33
WARNING: Photo electric beams must be
installed if the closing force at the bottom edge of
the door exceeds 400N (40kgf)
Step 16.1 - Testing Close Cycle
a.
b.
fig 34
c.
Press the OPERATE button to open the door (Fig.
33).
Place a piece of timber approximately 40mm high
on the floor directly under the door (Fig. 34).
Press the OPERATE button to close door. The door
should strike the object and start to re-open.
Step 16.2 - Testing Open Cycle
a.
b.
c.
Press the OPERATE button to close the door (Fig.
33).
Press again to open the door. When the door
reaches the half open point, grab the bottom rail of
the door firmly and the door should stop.
If the door does not reverse readily when closing,
or stop when opening, the force may be excessive
and need adjusting, refer below.
DANGER! If the door fails these tests, put the
opener into manual mode, only operate the door
by hand and call for service.
20
GDO-11v1 SecuraLift® Owner Installation Instructions
Adjusting Safety Obstruction Forces
Adjusting Safety Obstruction Force
The Safety Obstruction Force is calculated automatically
during setup. Adjusting this is normally only necessitated
by environmental conditions such as windy or dusty areas,
and areas with extreme temperature changes.
WARNING: Photo electric beams must be
installed if the closing force at the bottom edge of
the door exceeds 400N (40kgf)
fig 35
Step 17.1 - To Increase Force Pressure
a.
b.
c.
d.
Hold down FORCE MARGIN SET button (Fig. 35)
While holding the FORCE MARGIN SET button,
press the PLUS (+) button. Each press increases the
force margin (Fig. 35).
The OPEN LIMIT LED will flash each time the PLUS
(+) button is pressed to indicate a force increase
»
If the OPEN LIMIT LED on continuously
when pressing the PLUS (+) button this
indicates that the maximum setting has
been reached.
Test the force again as per Steps 16.1 and 16.2
Step 17.2 - To Decrease Force Pressure
a.
b.
c.
d.
Hold down FORCE MARGIN SET button (Fig. 35)
While holding the FORCE MARGIN SET button,
press the MINUS (-) button. Each press decreases
the force margin (Fig. 35).
The CLOSE LIMIT LED will flash each time the MINUS
(-) button is pressed to indicate a force decrease
»
If the CLOSE LIMIT LED on continuously
when pressing the MINUS (-) button this
indicates that the minimum setting has
been reached.
Test the force again as per Steps 16.1 and 16.2
fig 36
Step 17.3 - To Recall Factory Set Force
a.
b.
While holding down the FORCE MARGIN SET
button, press the SET button for two (2) seconds.
(Fig. 36)
Release both buttons. The default setting should
now be recalled.
Step 17.4 - To Recalculate Force Margins
a.
b.
c.
d.
Press and hold the SET Button for two (2) seconds,
the beeper will sound once (Fig. 37).
The door will start to move and re-calculate force
margins. The door can move between the open and
close limit positions up to four (4) times (depending
on the position of the door and the power up
condition).
A single beep will be heard once the process is
complete.
Test the force again as per Steps 16.1 and 16.2.
fig 37
Owner Installation Instructions GDO-11v1 SecuraLift®
21
Coding Transmitters
Step 18.1 - Code a Transmitter Button for
Door Operation
a.
b.
fig 38
c.
d.
Press and hold the DOOR CODE button (Fig. 38).
Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
Release the DOOR CODE BUTTON.
Press the transmitter button to test.
Step 18.2 - Code a Transmitter Button to
Enable Vacation mode
The opener can be programmed into a “Vacation
Mode” where the opener will not respond to any
transmitter except the button of the transmitter the one
programmed for vacation mode.
a.
b.
c.
d.
e.
fig 39
Briefly press the DOOR CODE button once, then
press it again and hold (will beep two times on
second press (Fig. 39)).
Press one of the four (4) buttons on the transmitter
for two (2) seconds, pause for two (2) seconds,
then press the same button again for two (2)
seconds.
Release DOOR CODE button.
Press and hold the transmitter button for six (6)
seconds to set Vacation Mode. the door code led
will stay lit while vacation mode is active.
To reset Vacation Mode press the same button
for two seconds.
Step 18.3 - Code a Transmitter Button to
Enable AUX OUTPUT
a.
b.
c.
d.
fig 40
22
GDO-11v1 SecuraLift® Owner Installation Instructions
Briefly press the DOOR CODE button two (2)
times, then press it again and hold (will beep
three times on third press (Fig. 40)).
Press one of the four buttons on the transmitter
for two (2) seconds, pause for two (2) seconds,
then press the same button again for two (2)
second.
Release the DOOR CODE button.
Press the transmitter button to test.
Coding Transmitters
Step 18.4 - Code a Transmitter Button for Pet
(Pedestrian) Mode
a.
b.
c.
d.
e.
Briefly press the DOOR CODE button three times,
then press it again and hold (will beep four times on
fourth press (Fig. 41)).
Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
Release the DOOR CODE button.
Press the transmitter button to test.
To change the default pet (pedestrian) door opening
position, refer Step 2.
fig 41
Step 18.5 - Coding a Transmitter Button to
the Courtesy Light
The transmitter can be programmed to operate the
courtesy light on the opener independently of the door
moving.
a. Briefly press the DOOR CODE button four times,
then press it again and hold (will beep five times on
fifth press (Fig. 42)).
b. Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
c. Release the DOOR CODE button.
d. Press the transmitter button to test the courtesy
light.
fig 42
Owner Installation Instructions GDO-11v1 SecuraLift®
23
Remote Coding & Deleting
Transmitters
Step 19 - Remotely Coding Transmitters
Using this method transmitters can be coded without
access to the opener’s control panel as long as a precoded transmitter is available.
IMPORTANT NOTE: The door or courtesy light
must activate when the steps below are performed.
This indicates that the pre-coded transmitter is in
range of the opener, and the correct button has
been pressed.
fig 43
a.
b.
c.
d.
e.
Take any pre-coded transmitter. Press the button
for the function to be duplicated and release.
Using a small needle, press and hold firmly for
two seconds through the Coding Hole (Fig. 43).
WITHIN 10 SECONDS take the additional
transmitter you wish to code. Decide which
button that you want to activate the function to
be duplicated (e.g. activate the door, or turn on
the courtesy light)
Hold the new transmitter’s button for two
seconds, pause for two seconds, hold again for
two seconds and then release.
Wait for 10 seconds and then press the new
transmitter’s button to test.
Step 19.1 - Deleting a Stored Transmitter
Code
fig 44
a.
b.
c.
d.
Select the transmitter you want to delete.
Press and hold the DOOR CODE BUTTON (Fig.
44).
Press the transmitter button you would like to
delete for two seconds, pause for two seconds,
press again for two seconds and then release.
Release the DOOR CODE BUTTON. The code
should now be deleted. Confirm this by pressing
the transmitter button - the function (e.g. door
opening) should not respond.
Step 19.2 - Deleting All Transmitter Codes
a.
b.
c.
fig 45
24
d.
GDO-11v1 SecuraLift® Owner Installation Instructions
Turn off power to the opener.
While switched off, press and hold the DOOR
CODE BUTTON (Fig. 45). Turn on power to the
opener while holding this button.
The OPEN LIMIT, CLOSE LIMIT and DOOR
STATUS LEDs will illuminate for about five
seconds. These LED’s will turn off and the
CODING LED will illuminate.
Release the DOOR CODE BUTTON. All stored
codes will now be deleted. Confirm this pressing
buttons on any previously coded transmitters the opener should not respond.
P.E. Beams
Step 20 - Fitting the P.E. Beams (optional)
b.
c.
WARNING: When using P.E. Beams, the doorway
must be clear of all obstructions and persons at all
times. The location of the beams and manner in
which it is installed might not give safety protection
at all times. Check to make sure that the height of
the beam and type used give maximum protection
possible.
Receiver
Transmitter
Model PE-2
RED
RED
RED
RESISTOR = 2K2
0.25 WATT
+ -
+ -
fig 46
BLACK
BLACK
BLACK
BLACK
YELLOW
RED
RED
RED
YELLOW
PWR
PE
PE(0V )
GND
OSC
AUX OUT
Affix the P.E. Beams in a strategic location within
the doorway. We recommend 150mm above the
floor level and as close as possible to the door
opening, inside the garage.
Connect the wires from the P.E.Beams wiring
harness to terminal block (Fig. 46). The wiring
diagram is for Model PE-2 (Order Code 90214).
Make sure that you are using the correct resistor
i.e. 2k2 ohms (Red Red Red gold) and connecting
to number 2 (two) and 4 (four) terminal on the PE-2
receiver. Make sure to align the beams correctly.
Follow the manual supplied with the P.E. Beams.
GOLD
a.
WARNING: Install the P.E.Beams as per diagram in
(Fig. 46). Tampering with P.E.Beams could result
in serious personal injury and/or property damage
and will void the warranty.
Step 21 - key switch connection
fig 47
Gdo-11v1 Has The Input To Connect Bell Switch
Or Key Switch To Open Or Close The Door.
Connect The Key/bell Switch As Per Diagram (Fig.
47).
30V PWR
PE
PE (0V)
GND
OSC
AUX OUT
Step 22 - Auxiliary out put
The auxiliary output can be used to control alarm or
another garage door opener. A valid transmission
from the pre-coded transmitter will cause the
auxiliary out put to pulse for approximately 1
(one) second. The maximum DC voltage must not
exceed 35 volts DC. Maximum current must not
exceed 80 ma.(Fig. 48).
External
device
Alarm, Door
opener etc.
PWR
PE
PE(0V )
GND
OSC
AUX OUT
Owner Installation Instructions GDO-11v1 SecuraLift®
fig 48
25
Battery Back Up Installation
fig 49
Step 23.1 - Connect the Battery Back Up Kit
a.
b.
c.
d.
e.
f.
g.
h.
Disconnect power to the opener.
Swing open the light diffuser and controls cover.
Remove screws marked “S” above in fig and lift up
the main cover. (Fig 49).
Feed the SBY-3 charger harness through the
grommet on the metal plate and connect to SBY-3
as shown in wiring diagram.
Mount the brackets RA (item no 9) to battery pack
with item 7 and 8
Secure the battery pack to gdo-11 with 2 screws
item no 5.
Feed the SBY-3 battery harness (item no 3 ) through
the grommet on the metal chassis and connect to
SBY-3 as per diagram.
Mount the pcb support (item no 10) with two screws
( item no 5). Secure the SBY-3 charger board on to
pcb support with 3 screws (item no 6).
Feed charger harness from SBY-3 to the control
board and plug into the 4 pin connector marked
“SBY-3” onto the control board.
i
j
Connect battery harnesses item 3 and 4
together
(Fig 49).
Reconnect power.
Step 23.2 - Testing Battery Back Up
a.
b.
Press either the OPERATE button or transmitter
to test the opener.
Whilst door is in motion disconnect mains
power the door should continue to operate as
normal.
NOTE: Wait for the door to complete its travel.
c.
d.
Press the OPERATE button or transmitter to
activate the door.
Whilst door is in motion re-connect power. The
door should complete the cycle as normal.
Step 23.3 - Troubleshooting
WARNING: After Step 23.1 (i) the opener may
become active (even when power is off). This is a
result of a residual charge in the batteries.
26
GDO-11v1 SecuraLift® Owner Installation Instructions
If door stops or moves very slowly under battery
power, the batteries may be weak or have no
charge. Connect mains power and allow the
batteries to charge. This may take 24 - 48 hours to
reach maximum charge capacity.
SmartSolar™ Installation
WARNING: Do not connect batteries until Step
24.3
Step 24.1 - Mount the Charger Board
a.
b.
c.
d.
e.
f.
g.
Disconnect power to the opener.
Swing open the light diffuser and controls cover.
Remove screws marked “S” above in fig and lift up
the main cover. (Fig 50).
Remove the transformer and mains power cable.
Mount the pcb support with two screws .Secure
the SBY-3 charger board on to pcb support with 3
screws. (Fig. 51).
Plug the solar charger Board’s three wire harness
(red/yellow/black) into the control board’s “SBY-3”
connector on the control board.
Plug the Charger Board’s white one wire harness
into the control board’s “24vac in” connector.
Plug the solar shunt (supplied) onto the control
board’s “JP1” solar connector.
S
S
Fig 50
IMPORTANT WARNING: Do not connect battery
or solar panel polarity incorrectly - this will result in
serious damage to components.
Fig 51
Step 24.2 - Connect the Solar Panel
a.
b.
c.
Mount the solar panel as outlined in the SmartSolar™
Installation Manual.
Feed the Solar Panel’s cable through black grommet
located on the top of the metal plate.
Connect the red wire to the Charger Board’s
“SOLAR+” connector, and the black wire to the
“–SOLAR” connector (Fig. 52).
WARNING: During Step 24.3 the opener will
become active.
Black
Yellow
Red
e
Whit
f.
Red (From Ba
ttery)
e.
ttery)
d.
Fig 52
Black (From Ba
c.
Mount the Battery Box close to the opener.
Feed the 2-core 18awg gauge cable (supplied)
through the Battery Box’s grommet.
Connect the red wire to the Battery Box’s “+” terminal,
and the black wire to the “–” terminal (Fig. 53).
Feed the other end of the battery cable through the
drive unit’s black grommet located on the metal
plate.
Connect the red wire to the Charger Board’s
“BAT+” connector, and the black wire to the “–
BAT” connector (Fig. 52).
Refit the light diffuser and main cover.
Red (From Solar P
anel)
a.
b.
olar Panel)
Black (From S
Step 24.3 - Mount & Connect the Battery
ire
W
ck
ire
a
l
B
dW
e
R
Fig 53
Step 24.4 - Re-setup and Test the Opener
a.
b.
Setup travel limits and code transmitters as per the
GDO-11v1 instruction manual.
Press either the OPERATE button or use a transmitter
to operate the opener.
Owner Installation Instructions GDO-11v1 SecuraLift®
27
Final Set Up
Step 25 - Setting the Pet Mode position
The default Pet Mode height can be changed as follows:
a. Make sure the door is closed, then press and hold
the PLUS(+) button for six (6) seconds (Fig. 54),
until you hear three beeps and the OPEN and
CLOSE LEDs flash rapidly.
b. Press the OPEN or CLOSE button to move the
door to the desired pet mode open position.
c. Press the SET button to record the new position.
fig 54
When activated, Pet Mode drives the door to the preset
position from either above or below. Pet Mode’s active
status is indicated by both the OPEN and CLOSE LIMIT
LEDs being illuminated. If a Pet Mode button is pressed
while the door is moving the door will stop. If a Pet
Mode button is pressed when the door is in the Pet
position, then the door will close.
Step 26 - Installing the Wall Mounted
Transmitter (Optional)
a.
b.
c.
d.
fig 55
Remove the faceplate from the transmitter.
Affix the baseplate in a convenient wall location
(Fig 55) that is the door is visible from this
location. but out of the reach of children at a
height of at least 1.8 meters from the floor.
Replace the faceplate.
To code the transmitter, see Steps 10.1 through
10.4 on page 19.
Step 27 - Reset all Factory Defaults
a.
b.
c.
fig 56
28
GDO-11v1 SecuraLift® Owner Installation Instructions
Turn power to opener off.
Press and hold the SET Button (Fig 56).
Turn power on while holding the SET button.
Continue to hold until all LEDs are off.
»
This will not erase transmitter codes
stored in memory.
Default Settings & Specifications
Factory default settings
Default
Step
Maximum
Maximum motor run time
60 Secs.
-
-
Courtesy light time
3 Mins.
10 Sec in battery back
up mode
Obstruction force margin
0.5 Amp
0.1
2 Amp
Technical specifications
Power supply
230V - 240V AC 50Hz
Transformer rating
72 VA
Standby power
2.2 Watts
Motor power
90 Watts
Motor type
24V DC permanent magnet
Shuttle travel distance in the C-Rail
3.1m approx (standard)
Maximum shuttle travel distance in the C-Rail
4m (with extended C-Rail)
Maximum door opening:
(With 3160mm Standard track)
5500mm (12m2)
2150mm
80 kg
Width:
Height:
Weight:
Minimum Clearance
(Bottom of C-Rail to highest point of door travel)
25mm
Short term peak force
650N (65kg)
Lift force
400N (40kg)
Nominal force
150N (15kg)
Receiver type
Multi-frequency FM Receiver
Receiver code storage capacity
8 x 4 button transmitter codes
Transmitter frequency
~= to 433.92 MHz
Coding type
TrioCode™
Number of code combinations
Over 4.29 billion random codes
Code generation
Non-linear encryption algorithm
Transmitter battery
CR 2032
Courtesy light
Festoon style lamp 24 volts 15 watts
Controller fuse
10A slow blow
NOTE: Intermittent operations may occur in areas which experience very strong winds. The strong wind
puts extra pressure on the door and tracks which may in turn trigger the safety obstruction detection system
intermittently.
P.E Beams should be fitted as added safety in case of entrapment.
Owner Installation Instructions GDO-11v1 SecuraLift®
29
Parameters
Door Status Indicators
Door Opener State
OPEN LED (Green)
Open
On
Close
Opening
CLOSE LED (Red)
Beeper
On
Flashing
Closing
Flashing
Door travel stopped
Flashing
Door obstructed when opening
Flashing
Door obstructed when closing
Flashing
Flashing
Opener overloaded
Alternating flashes
Alternating flashes
Pet Mode Engaged
On
On
Mains power interrupted
Rapid flashes
Beeps as door moves
Button Functions
30
Buttons
Function
OPERATE
Opens/Stops/Closes the door
DOOR CODE
Codes a transmitter button for operate function,
Vacation function, Auxilary function, Pet mode and
Light function
FORCE MARGIN SET & OPEN
Increases the obstruction force margin setting
FORCE MARGIN SET & CLOSE
Decreases the obstruction force margin setting
FORCE MARGIN SET (then) SET
Resets the factory default force margin settings
CLOSE (for 6 secs.)
Clears the door limits set positions. Limits then
need to be reset
PLUS(+) (for 6 secs.)
Enters pet (pedestrian) position mode
SET (then power on) & hold until all LEDs are off
Deletes control parameters excluding transmitter
storage memory
DOOR CODE (then power on) & hold until all LEDs
are off
Deletes all transmitter storage memory
SET & DOOR CODE (the power on) and hold until all
LEDs are off
Deletes all control parameters and transmitter
storage memory.
SET
Re-initialises the Opener to re-calculate force
margin
GDO-11v1 SecuraLift® Owner Installation Instructions
Troubleshooting guide
Symptom
Door will not operate
Door starts to close but
automatically reverses to
open position
Possible cause
Remedy
Mains power not switched on
Switch on mains power
Door is obstructed
Remove obstruction
Door is locked or motor jammed
Unlock door or remove jam
Door tracks/hardware damaged
Door requires service/repair by
qualified technician
Adverse weather conditions (wind
or cold) causing door to stiffen and
become tight in the tracks
Increase force margin setting.
See Step 17 on page 21
Possible obstruction in
the doorway
Door operates from drive unit
(operate) button but not from
transmitter.*
Transmitter code not stored
in memory
Flat battery
*See note
Remove obstruction
Code transmitter into opener’s
memory. Refer Step 18.1 on page
22
Replace battery
Door will not close fully
Door limits position need to
be reset
Reset limits positions. Refer Step
15.4 on page 19
Door will not open fully
Door limits position need to
be reset
Reset limits positions. Refer Step
15.4 on page 19
Courtesy light not working
Faulty light
Replace lamp
PE Beam click but door does not
reverse open when PE Beam is
obstructed during close cycle
Wrong value of resistor is used
2k2 ohms resistor must be used on
the receiver of PE Beam
PE Beam or wiring faulty
PE Beam not aligned correctly
PE Beam is obstructed
Remove obstruction
See Step 20 on page 25
PLEASE NOTE:
Some areas may be prone to excessive radio interference brought on by devices such as cordless telephones,
wireless stereo headphones and baby monitors. It is possible that these devices could cause a degree of
interference such as to greatly reduce the range of the transmitter. In such an instance please contact your ATA
dealer for an alternative frequency replacement kit. As this is not a warrantable situation but an environmental
issue charges may apply for the changeover.
Owner Installation Instructions GDO-11v1 SecuraLift®
31
Maintenance
Maintenance
Yearly
Whilst your opener does not require any periodic
maintenance, the door that it is fitted to does.
Your garage door is a large, heavy, moving object
and should be tested regularly to ensure it is in
good condition. A poorly maintained door could
cause fatal or serious injuries or serious damage to
property.
Automatic Technology suggests you contact your
installer to perform an annual door service.
To ensure a long and trouble free life for your opener
the following is recommended:
Monthly
•
•
Disengage the opener and manually operate
the door: The door must be smooth to operate
by hand. An operating force on the bottom rail
should not exceed 150N (15kg) force.
Each month check that the opener reverses
when the door contacts a 40mm high object
placed on the floor (AS3350).
CAUTION: Frequently examine door, particularly
cables, springs and mountings for signs of wear,
damage or imbalance. Do not use if repair
or adjustment is needed since a fault in the
installation or an incorrectly balanced door may
cause injury. (AS3350)
Adjustments should only be carried out by
experienced persons, as this function can
be dangerous if not performed under strict safety
procedures.
WARNING! Failure to maintain your garage
door may void the warranty on your garage door
opener.
•
NOTE: If the door does not operate smoothly, call
your installer.
Service Record
Record any maintenance in the following table to assist in any warranty service.
Date
32
Service by
Signature
GDO-11v1 SecuraLift® Owner Installation Instructions
Invoice No.
Amount
Parts Listing
Owner Installation Instructions GDO-11v1 SecuraLift®
33
Warranty and Exclusion of Liability
1. This warranty is an addition to any non-excludable conditions or warranties that are implied into this contract
by relevant statute, including the Trade Practices Act 1974 (Cwth).
2. Subject to all of the matters set out below, Automatic Technology Australia Pty Ltd (“ATA”) warrants:
(a) overhead door opener drive units for twelve (12) months or 2500 cycles, whichever occurs first; and
(b) all components and accessories for twelve (12) months, from the date of purchase (specified in the sales
docket receipt) as free of any defects in material and workmanship.
3. This warranty applies only where the purchaser:
(a) immediately notifies ATA or the retailer of the alleged defect;
(b) returns the product to the retailer; and
(c) presents the relevant sales docket and this warranty document to the retailer to confirm the date
of purchase.
4. Except for this warranty, ATA gives no warranties of any kind whatsoever (whether express or implied),
in relation to the product, and all warranties of whatsoever kind relating to the product are, to the extent
permissible by statute, hereby excluded.
5. To the extent permissible by statute, ATA disclaims any liability of whatsoever nature in respect of any claim
or demand for loss or damage which arises out of:
(a) accidental damage to or normal wear and tear to the product or to the product’s components;
(b) any cost relating to damage resulting from wear and tear;
(c) blown fuses, loss or damage caused by electrical surges, power surges or power spikes;
(d) loss or damage due to theft, fire, flood, rain, water, lightning, storms or any other acts of God;
(e) maximum continuous operating time exceeding one (1) minute in ten (10);
(f) maximum operating force exceeding *15kg (150N) when moving the door manually to the open or
closed position;
(g) door surface area and/or weight exceeding 12m2 and 80kg respectively;
(h) door not in safe and correct working order and condition;
(i) evidence of unauthorised repairs;
(j) any cost relating to damage caused by misuse, negligence or failure to maintain the equipment in a
proper working order as per clauses (d) through (h);
(k) installation, adjustment or use which is not in accordance with the instructions set out in installation
instruction manual
(l) attempted or complete modification or repairs to the product carried out by a person who is not
authorised or has not been trained by ATA to carry out such modification or repairs;
(m) faulty or unsuitable wiring of structure to which the product is fixed or connected;
(n) radio (including citizen band transmission) or any electrical interference;
(o) damage caused by insects;
(p) loss or damage to any property whatsoever or any loss or expense whatsoever resulting or arising there
from or any consequential loss;
(q) any cost or expense arising due to manufacturer recall of any product;
(r) any cost or expense due to negligence of the approved service provider;
(s) installation of a residential garage door opener in a commercial or industrial situation or a non-single
residential dwelling.
6. ATA’s liability under this warranty is limited, at ATA’s absolute option, to replacing or repairing the product
which ATA, in its unfettered opinion, considers to be defective either in material and/or workmanship or to
credit the dealer with the price at which the product was purchased by the dealer.
7. This warranty does not extend to cover labour for installation.
8. This warranty is limited to Return-to-Base (RTB) repair and does not cover labour for on-site attendance.
9. This warranty is void if the Product is not returned to the manufacturer in original or suitably secure packaging.
10. This warranty is only applicable for repairs to the product carried out within Australia.
11. This warranty does not cover consumable items including globes, batteries and fuses.
12. This warranty is not transferable.
13. Where the Product is retailed by any person other than ATA, except for the warranty set out above, such
person has no authority from ATA to give any warranty or guarantee on ATA’s behalf in addition to the
warranty set out above.
NOTES:
1. One (1) cycle = one (1) open and one (1) close action of the door or gate.
2. This warranty is to be read in conjunction with the owner’s copy of the installation instruction manual.
3 *The door should be balanced in such a way that the user manually is able to open or close the door without using
force not greater than 150N (15kg ) although a greater force may be required for the start of the movement.
34
GDO-11v1 SecuraLift® Owner Installation Instructions
Owner Installation Instructions GDO-11v1 SecuraLift®
35
© August 2008 Automatic Technology (Australia) Pty Ltd. All rights reserved. TrioCode™ and SecuraLift ® are trademarks
of Automatic Technology (Australia) Pty Ltd. No part of this document may be reproduced without prior permission. In an
ongoing commitment to product quality we reserve the right to change specification without notice. E&OE.
Automatic Technololgy (Australia) Pty Ltd
ABN 11 007 125 368
6-8 Fiveways Boulevard
Keysborough, Victoria, 3173, Australia
P 1300 133 944
+61 2 9722 5666 (International Enquiries Only)
E sales@ata-aust.com.au
www.ata-aust.com.au
GARAGE DOOR OPENERS | GATE OPENERS | REMOTE CONTROL ACCESS SOLUTIONS