Cybex Eagle® Calf
Owner’s Manual
Strength Systems
Part Number 11120-999-4 A
www.cybexinternational.com
Cybex Eagle® Calf
Owner’s Manual
Strength Systems
Part Number 11120-999-4 A
Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.
Eagle® and its mark are registered trademarks of Cybex International, Inc.
DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual. We reserve the right to
revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such
revisions or changes.
© Copyright 2010, Cybex International, Inc. All rights reserved.
Printed in the United States of America.
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • techhelp@cybexintl.com • 11120-999-4 A
Table of Contents
1 Safety
Safety. . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Guidelines and Practices . . . . .
Warning/Caution Decals . . . . . . . . . . .
Regular Maintenance Activities . . . . . .
Using Proper Form . . . . . . . . . . . . . . .
1-1
1-2
1-3
1-5
1-5
2 Exercises
Intended Use . . . . . . . . . . . . . . . . . . . . 2-1
Instructions. . . . . . . . . . . . . . . . . . . . . . 2-1
3 Customer Service
Contacting Service. . . . . . . . . . . . . . . .
Ordering parts . . . . . . . . . . . . . . . . . . .
Return Material Authorization (RMA). .
Damaged Parts . . . . . . . . . . . . . . . . . .
3-1
3-1
3-1
3-2
4 Assembly
Assembly . . . . . . . . . . . . . . . . . . . . . . . 4-1
5 Maintenance
Daily Procedures . . . . . . . . . . . . . . . . .
Weekly Procedures . . . . . . . . . . . . . . .
Yearly Procedures . . . . . . . . . . . . . . . .
Environment. . . . . . . . . . . . . . . . . . . . .
Storage . . . . . . . . . . . . . . . . . . . . . . . .
Page i
5-1
5-4
5-6
5-7
5-7
Cybex Eagle 11120 Standing Calf Owner’s Manual
1 - Safety
Safety
Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
It is the responsibility of the facility owner and/or owner of the equipment to instruct users on proper operation of the
equipment and review all labels.
WARNING: Serious injury could occur if these safety precautions are not observed:
User Safety Precautions
•
Obtain a medical exam prior to beginning an exercise program.
•
Read and understand warning labels and user manual prior to exercising. Obtain instruction
prior to use.
•
Keep body and clothing free from and clear of all moving parts.
•
Inspect machine prior to use. DO NOT use if it appears damaged or inoperable.
•
DO NOT attempt to fix a broken or jammed machine. Notify floor staff.
•
Use the machine only for the intended use. DO NOT modify the machine.
•
Be sure that the weight pin is completely inserted. Use only the pin provided by the manufacturer.
If unsure seek assistance.
•
Never pin the weights in an elevated position. DO NOT use the machine if found in this condition.
See assistance from floor staff.
•
Children must not be allowed near these machines. Teenagers must be supervised.
•
DO NOT use if guards are missing or damaged.
•
DO NOT use dumbbells or other incremental weights, except those provided by the manufacturer.
•
Inspect all cables and belts and connections prior to use. DO NOT use if any components are worn, frayed or
damaged.
•
DO NOT remove any labeling from equipment. Replace any damaged labels.
•
Stop exercising if you feel faint, dizzy or experience pain at any time while exercising and consult your
physician.
Facility Safety Precautions
•
Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
•
Securely anchor each machine to the floor using the anchor holes provided in each machine.
NOTE: Cybex is not responsible for the actual anchoring of equipment. Consult with a professional
contractor.
NOTE: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8” grade 2 bolts or better).
NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any
leg or frame not in contact with surface using flat washers.
Safety
Page 1-1
Cybex Eagle 11120 Standing Calf Owner’s Manual
•
Make sure that each machine is set up and operated on a solid level surface. Do not install equipment on an
uneven surface.
•
Make sure that all users are properly trained on how to use the equipment.
•
Make sure there is enough room for safe access and operation of the equipment.
•
Perform regular maintenance checks on the equipment. Also pay close attention to all areas most susceptible to wear,
including (but not limited to) cables, pulleys, belts and grips.
•
Immediately replace worn or damaged components. If unable to immediately replace worn or damaged components
then remove from service until the repair is made.
•
Use only Cybex supplied components to maintain/repair the equipment.
•
Keep a repair log of all maintenance activities.
•
Inspect all cables and belts and connections prior to use. DO NOT use if any components are worn, frayed or
damaged.
NOTE: It is the sole responsibility of the user/owner or facility operator to ensure that regular maintenance is performed.
Safety Guidelines And Practices
Cybex recommends that all fitness equipment be used in a supervised area. It is recommended that the equipment be
located in an access controlled area. Control is the responsibility of the owner. The extent of control is at the discretion of
the owner.
It is the responsibility of the purchaser/user of Cybex products to read and understand the owner’s manual, and warning
labels; as well as instruct all individuals, whether end users or supervising personnel, on proper usage of the equipment.
PROPER USAGE:
Use machine only as described in the manual. Failing to follow proper instructions may result in injury.
Do Not Lean Against or Pull On the framework, weight stack, or any component, whether machine is at rest or in use.
Inappropriate or improper use may result in injury to users or third parties (bystanders).
Do not use machine if it is not located on a solid level surface or is improperly installed.
Provide an adequate safety perimeter between the machine, walls and other equipment to ensure that the facility has the
proper clearance for usage and training.
SECURING EQUIPMENT:
The machine has holes in the feet, which allow for ease in anchoring to the floor. Cybex strongly recommends that,
to eliminate rocking, tipping or falling over due to incorrect usage and misuse, equipment be secured to a solid, level
surface.
1. The solid, level surface should not deviate more than 1/8” over a 10’ distance or as defined and required by local
building and architectural codes.
2. Anchoring of equipment must be completed by a qualified licensed contractor.
Safety
Page 1-2
Cybex Eagle 11120 Standing Calf Owner’s Manual
3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when anchoring the
equipment to the floor.
4. Due to the wide variation of flooring on which machines may be anchored or installed, verify anchoring method and
anchoring fasteners with a qualified and licensed contractor.
5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position..
6. Do not use machine until it is properly anchored.
MAINTENANCE:
Preventative maintenance allows proper equipment operation and reduces the risk of injury. Perform the maintenance
requirements as specified in the manual.
STANDARD COMPLIANCE:
Cybex products meet or exceed applicable ASTM and EN Standards.
Warning/Caution Decals
Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
Caution decals indicate a potentially hazardous situation, which, if not avoided, could result in minor or moderate injury.
The warning and caution decals are shown on the following page. The diagrams following the decals show where each
decal is located.
Safety
Page 1-3
Cybex Eagle 11120 Standing Calf Owner’s Manual
A
B
CAUTION
Personal injury may occur.
Keep away from moving
parts to avoid injury.
4000Y316-4 A
Safety
Page 1-4
Cybex Eagle 11120 Standing Calf Owner’s Manual
Standing Calf - 11120
A
B
B
B
DESCRIPTION
PART NO.
A. Warning Label ................. 4605-381-4
B. Caution Decal ................. 4000Y316-4
Safety
Page 1-5
Cybex Eagle 11120 Standing Calf Owner’s Manual
Regular Maintenance Activities
Preventative maintenance activities must be performed to maintain normal operation of your equipment. Keeping a
log sheet of all maintenance actions will assist you in staying current with all preventative maintenance activities. The
preventative maintenance actions are described in detail in Chapter 5.
Briefly, they include:
Daily
1. Clean upholstery.
Weekly
1. Inspect all nuts and bolts for looseness. Tighten as required.
2. Inspect all cables and belts for damage or wear (see Chapter 5). If a cable or belt is worn or damaged,
immediately discontinue use until cable or belt has been replaced.
3. Check for worn handles, worn snap links, and worn warning labeling. Replace all worn parts immediately.
4. Inspect for loose or worn grips. Replace all loose or worn grips immediately.
5
Inspect weight stacks for proper alignment and operation. Correct all improper alignment and operation issues
immediately.
6. Lubricate guide rods using automotive engine oil only.
Yearly
1. Replace all cables and belts at least annually.
Using Proper Form
Before working out, read and understand the exercises located on the placard and in Chapter 2.
Safety
Page 1-6
Cybex Eagle 11120 Standing Calf Owner’s Manual
2 - Exercise
Intended Use
MUSCLES USED
The intended use of this equipment is to aid or
improve general physical fitness and exercise.
For Commercial use.
Instructions
Read and understand all instructions and warnings
prior to using this machine. See Chapter 1, Safety in
the Eagle Owner’s Manual or consult with floor staff.
Gastrocnemius, Soleus
FINISH
START
NOTE: Motion Developed: Plantar Flexion
NOTE: All adjustment points on the machine have yellow handles or knobs.
NOTE: See next page for “Set Up” and “Movement”.
NOTE: Do not turn knob when weight stack is elevated
Exercise
Page 2-1
Cybex Eagle 11120 Standing Calf Owner’s Manual
Set Up
1. Adjust seat for a slight bend at the knee with feet shoulder width apart.
2. Grasp handles.
Movement
1. Press ball of foot forward into the foot bar..
Exercise
Page 2-2
Cybex Eagle 11120 Standing Calf Owner’s Manual
3 - Customer Service
Contacting Service
Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m Eastern Standard Time.
For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239.
For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax 508-533-5183.
Find information on the web at www.cybexintl.com or e-mail at techhelp@cybexintl.com.
Ordering Parts
NOTE: All inspections
and repairs must be
performed by trained
service personnel only.
Fax orders to 508-533-5183. To speak with a customer service
representative, call 888-462-9239 (for customers living within
the USA) or 508-533-4300 (for customers outside the USA).
You may also contact us through e-mail at
techhelp@cybexintl.com.
Having the following information ready when calling, will assist our
Cybex representatives in serving you.
•
Unit Serial Number
•
Product Name
Cybex will void warranty if
non-Cybex replacement parts
are used.
The unit serial number and product name can be found on the serial number decal.
•
Part Description
•
Part Number
Part descriptions and part numbers are located on the web at www.cybexintl.com.
•
Shipping Address
•
Contact Name
In addition to your shipping address and contact name, your account number is helpful but not required.
Return Material Authorization (RMA)
The Return Material Authorization (RMA) system outlines the procedures to follow when returning
material for placement, repair or credit. The system assures that returned materials are properly handled and analyzed. Follow the
following procedures carefully.
Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will request a RMA from Cybex, if
applicable. Under no circumstances will defective parts or equipment be accepted by Cybex without proper RMA and an Automated
Return Service (ARS) label.
Customer
Service
Page 3-1
Cybex Eagle 11120 Standing Calf Owner’s Manual
1. Call the Customer Service Hot Line listed above for the return of any item that is defective.
2. Provide the technician with a detailed description of the problem you are having or the defect in the item you wish
to return.
3. Provide the model and serial number of your Cybex equipment.
4. At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for evaluation and
repair or replacement. The technician will assign you a RMA number and will send you an ARS label. The ARS
label and the RMA numbers must be clearly displayed on the outside of the package that contains the item(s) to be
returned. Include the description of the problem, the serial number of the equipment and the name and address of
the owner in the package along with the part(s).
5. Forward the package through UPS to Cybex.
Attn: Customer Service Department
Cybex International, Inc.
1975 24th Ave SW
Owatonna, MN 55060
NOTE: Merchandise returned without an RMA number on the outside of the package or shipments sent COD will not be
accepted by the Cybex receiving department.
Damaged Parts
Materials damaged in shipment should not be returned for credit. Shipping damages are the responsibility of the carrier (UPS, Federal
Express, trucking companies, etc.)
Apparent Damage - Upon receipt of your shipment, check all items carefully. Any damage seen with a visual check must be noted
on the freight bill and signed by the carrier’s agent. Failure to do so will result in the carriers refusal to honor your damage claim. The
carrier will provide you with the required forms for filing such claims.
Concealed Damage - Damage not seen with a visual check upon receipt of a shipment but notices later must be reported to the carrier
as soon as possible. Upon discovery of the damage, a written or phone request to the carrier asking them to perform an inspection
of the materials must be made within ten days of the delivery date. Keep all shipping containers and packing materials as they will be
needed in the inspection process. The carrier will provide you with an inspection report and the necessary forms for filing a concealed
damage claim. Concealed damage claim is the carrier’s responsibility.Cybex, if applicable. Under no circumstances will defective parts
or equipment be accepted by Cybex without proper RMA and an Automated Return Service (ARS) label.
Customer
Service
Page 3-2
Cybex Eagle 11120 Standing Calf Owner’s Manual
4 - Assembly
TOOLS REQUIRED
•
•
•
•
•
•
•
•
7/32” Allen wrench
3/4” Allen wrench
9/16” Wrench
3/4” Socket or wrench
External snap ring pliers
Phillips screwdriver
Medium weight automotive engine oil
Torque Wrench
ITEM
1
2
3
4
QTY
PART NO.
DESCRIPTION
6
1
1
19
11090-392
12000-560
12000-561
4000C101
FOOT PAD
DECAL, WEIGHT PLATE (30- 290)
DECAL, WEIGHT PLATE (310-490)
WEIGHT STACK PLATE
30
2
1
NOTE: Two people will be required for this procedure.
50
13.5
22.5
70
31.5
90
40.5
110
49.5
130
58.5
150
67.5
170
4
76.5
190
85.5
210
94.5
230
3
103.5
250
112.5
270
121.5
290
130.5
NOTE: It is the responsibility of the facility owner/owner of the
equipment to ensure that there is appropriate clearance
around each machine to allow for safe use and passage.
1. Read and understand all instructions thoroughly before starting any of the
procedures listed on this instruction sheet.
2. Verify you have received the appropriate configuration.
A. Verify that you received the correct color machine that you ordered.
B. Verify you received weight plates and weight plate decals.
C. Verify you received the Cybex Eagle Calf Raise Owner’s Manual.
D. Verify you received the warranty sheet.
3. Move to desired location.
A. Note the diminsions of the machine:
idle 58 L x 41 W x 58 H inches
147.32 L x 104.14 W x 147.32 H cm
in use - 66 L x 41 W x 58 H inches
167.64 L x 104.14 W x 147.32 H cm
Machine Weight (with weight stack) - 740 lbs. (335.66 kg)
B. Determine if you can move your machine through the required doorway(s).
C. If the machine fits through the doorway(s), move machine to desired location and skip to step 5.
D. If weight stacks need to be installed proceed to step 6.
E. If the machine does not fit through the door-way(s) then see step 4.
4. Doorway Instructions.
NOTE: If your machine fits through the doorway then skip step 4.
If your machine does not fit through the doorway then perform step 4.
A. Carefully remove each (standard) cone-shaped shipping support using a 3/4” socket or wrench.
Assembly
Page 4-1
Cybex Eagle 11120 Standing Calf Owner’s Manual
B. With an assistant, carefully remove the nine Button Head
Socket Cap Screws (BHSCS) securing the two halves of
the frame. See Figure 1.
Locknut (3)
Locknut (3)
BHSCS (2)
C. Carefully move each half through the door-way to the
desired location.
BHSCS (3)
D. With an assistant, carefully attach each half together
using the nine BHSCS removed in step 4B. See Figure 1.
Locknut (2)
E. Continue on with step 5B.
5. Remove shipping feet and remove the back shrouds.
A. Carefully remove each (standard) cone-shaped
shipping support (using a 3/4” socket or wrench).
Locknut (1)
BHSCS (3)
BHSCS (1)
Figure 1
B. Carefully place rubber feet (supplied with machine)
on each foot of the frame.
C. Cut shipping tie securing top weight.
D. Lift top weight and turn the Increment Weight Adjusting
Knob to select all 15 lbs.(three increment weights each
side).
E. Remove the three Phillips head screws securing the
top (back) shroud and carefully remove the shroud.
See Figure 2.
Phillips Head
Screw (3)
Figure 2
F. Loosen bottom two screws shown in Figure 3.
NOTE: Do not remove the bottom two screws.
G. Remove the top two screws securing the back shroud
assembly. See Figure 4.
Screw
H. Carefully slide rear shroud assembly upward and remove.
Figure 3
6. Install the weight stack.
A. Note how the increment weights are installed.
B. With an assistant holding the increment weights, move
the adjusting knob to 0 lbs. and remove all six increment
weights (three each side).
C. Using an external snap ring pliers, remove the upper
snap ring from one of the guide rods and carefully
lower the guide rod. See Figure 5.
Screw
Figure 4
D. Remove lower snap ring and wave washer from the
guide rod. Repeat steps 6C and 6D to remove both
snap rings from other guide rod.
Upper snap ring
Frame
E. If possible, lean guide rods outward, away from machine
in order to provide the most room for installing weight
plates.
Wave washer
Lower snap ring
F. Slide top weight up and out of machine and carefully
set it aside.
Assembly
Page 4-2
Guide rod
Figure 5
Cybex Eagle 11120 Standing Calf Owner’s Manual
G. Wipe guide rods clean over entire length. Lubricate with light coating of medium weight automotive engine oil.
H. Carefully install each weight plate one at a time. NOTE: When installing weight plates, position plates so wide
edges of bushing face upward and narrow edges of bushing face downward. See Figures 6A and 6B.
T
C
E
RR
CO
WIDE bushing
edge faces
upward
Figure 6A
I.
G
N
RO
W
NARROW
bushing edge
NOTE: The narrow bushing
edge must face downward.
Figure 6B
Slide top weight onto guide rods.
J. Place lower snap ring and wave washer onto guide rod (about 3” from the top end of guide rod).
K. Raise guide rod up through mounting hole and install the upper snap ring.
L. Lower guide rod and secure lower snap ring. Repeat steps 6J - 6L for the other guide rod.
7. Belt Routing.
Belt
A. Verify belt is routed through top of pulley bracket
and then route end of belt down to the top weight.
B. Verify the belt clamp on the top weight is positioned
properly with the top pulley. NOTE: The belt must
have a straight path from the pulley to the belt clamp.
See Figure 7. NOTE: Figure 7 shows the top view,
looking from the top pulley down to the top plate.
Set Screw
Top Pulley
Increment
Weight
Adjusting
Knob
Insert
C. Slide belt through slot in belt clamp.
Figure 7
D. Verify belt and insert are installed properly,
as shown in Figure 8A. NOTE: Do not install
the insert backwards as shown in Figure 8B.
Correct belt routing
Wrong belt routing
Insert
Insert
Belt
Belt
Stem
Figure 8A
Stem
Figure 8B
Assembly
Page 4-3
Cybex Eagle 11120 Standing Calf Owner’s Manual
E. Pull belt tight and secure belt to clamp with the two
set screws. NOTE: Torque set screws 300-350 in./lbs.
See Figure 9.
Belt clamp
insert
Belt
F. Place weight stack pin in each plate to verify proper installation.
G. Without selecting any resistance, lift top weight up and down
(simulating normal operation).
Belt clamp
Set screw
H. Have an assistant verify that the belt is moving smoothly and is
routed straight from the top pulley bracket to the
top weight belt clamp.
I.
Reinstall the six increment weights that were removed
in step 6B. See Figure 10.
J. Turn the Increment Weight Adjusting Kob to select all
15 lbs.
Figure 9
Increment
Weights
8. Install back shrouds.
NG
O
WR
CT
RE
R
CO
A. Carefully place shroud assembly back into position
on the two bottom screws. See Figure 11.
B. Install the top two screws securing the back shroud
assembly. See Figure 12.
C. Install the three Phillips head screws securing the
top (back) shroud. See Figure 13.
Figure 10
Screw
Figure 11
Screw
Figure 12
Phillips
Head
Screw (3)
Assembly
Page 4-4
Figure 13
Cybex Eagle 11120 Standing Calf Owner’s Manual
9. Install weight plate decals.
Front
NOTE: You have the option to use pounds, kilograms or both.
A. Slowly and carefully peel off back side of decal. See
Figure 14. NOTE: When peeling off back cover, make
sure that the decals remain attached to the front sticker.
B. Align holes in decal with appropriate holes in weight
stack. NOTE: Do not allow the adhesive to touch
weight stack at this time.
C. Insert a guide pin through each hole of the template.
NOTE: A guide pin can be anything that fits through the
weight stack hole, such as a weight stack selector pin.
Back
Figure 14
Guide Rod
D. Carefully align decal and rub it onto weight plates.
E. Carefully remove front side, leaving decals adhering to
weight plates. See Figure 15.
9.0
Weight Stack
20
NOTE: It is important that you perform regular inspection and
maintenance activities on your equipment. See the
Cybex Eagle Owner’s Manual for inspection and
maintenance activities. If you do not have a Cybex
Eagle Owner’s Manual or if you have any questions
or concerns, call Cybex Customer Relations at
888-462-9239.
80
100
120
140
160
180
200
220
240
260
280
Pounds
300
320
340
360
380
400
10. Verify proper operation
18.0
40
60
36.0
45.0
54.0
63.0
72.0
81.0
90.0
99.0
108.0
117.0
126.0
135.0
144.0
153.0
162.0
Kilograms
171.0
180.0
Figure 15
11. Anchor machine to the floor.
A. Securely anchor machine to the floor using the anchor holes provided in each machine.
NOTE: Cybex is not responsible for the actual anchoring of equipment.Consult with a professional contractor.
NOTE: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8” grade 2 bolts or better).
NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any leg or frame not
in contact with surface using flat washers.
Assembly
Page 4-5
Cybex Eagle 11120 Standing Calf Owner’s Manual
This page intentionally left blank.
Assembly
Page 4-6
Cybex Eagle 11120 Standing Calf Owner’s Manual
Chapter 5 - Maintenance
All preventive maintenance activities must be performed on a regular basis. Performing
routine preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex
Strength Systems equipment.
NOTE:
Cybex is not responsible for performing regular inspection and maintenance actions
for your machines. Instruct all personnel in equipment inspection and maintenance
actions and also in accident reporting/recording. Cybex phone representatives are
available to answer any questions or concerns that you may have.
NOTE: All inspections and
repairs must be
performed by trained
service personnel only.
Cybex will void warranty if
non-Cybex replacement parts
are used.
Daily Procedures
1. Upholstery - Wipe down all upholstery as per the recommendations listed below for light
soiling and more difficult stains.
Light Soiling
• A solution of 10% household liquid dish soap with warm water applied with a soft damp
cloth.
• If necessary, a solution of liquid cleanser and water applied with a soft bristle brush.
Wipe away the residue with a water dampened cloth.
Maintenance
Page 5-1
Cybex Eagle 11120 Standing Calf Owner’s Manual
More Difficult Stains
• Dampen a soft white cloth with a solution of 10% household bleach (sodium hypochlorite), 90%
water. Rub gently. Rinse with a water dampened cloth to remove bleach concentration.
• The same procedure can be used with full strength household bleach, if necessary.
• Allow bleach to puddle on the affected area or apply with a soaked cloth for approximately 30 minutes.
Rinse with a water dampened cloth to remove any remaining bleach concentration.
Alternative Method for Difficult Stains
• Dampen a soft white cloth with rubbing alcohol and rub gently. Rinse with a water dampened cloth to
remove any remaining rubbing alcohol concentration.
NOTE: To restore luster, a light coat of spray furniture wax can be used. Apply for 30 seconds and
follow with a light buffing using a clean white cloth.
Please Review Carefully
When using strong cleaning agents such as rubbing alcohol or bleach, it is advisable to first test in an
inconspicuous area. Other cleaning agents may contain harsh or unknown solvents and are subject to
formula changes by the product manufacturer without notice. Should you desire to use other cleaning
agents, carefully try them in an inconspicuous area to determine potential damage to the material.
Never use harsh solvents or cleaners which are intended for industrial applications. To clean stained or
soiled areas, a soft white cloth is recommended. Avoid use of paper towels.
Cleaning products may be harmful/irritating to your skin, eyes, etc. Use protective gloves and eye
protection. Do not inhale or swallow any cleaning product. Protect surrounding area/clothing from
exposure. Use in a well ventilated area. Follow all product manufacturer’s warnings. CYBEX and its
vendors cannot be held responsible for damage or injuries resulting from the use or misuse of cleaning
products.
2. Frames - Wipe down all frames using a mild solution of warm water and car wash soap. Be sure to dry
thoroughly. AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these
could scratch or damage the equipment.
3. Chrome - Clean chrome tubes, first using chrome polish and then using a car wax seal. Neutral
cleaners with a pH between 5.5 and 8.5 are recommended. Be sure to dry thoroughly. AVOID acid or
chlorine based cleaners and also cleaners containing abrasives as these could scratch or damage the
equipment.
Maintenance
Page 5-2
Cybex Eagle 11120 Standing Calf Owner’s Manual
4. Guidelines for cleaning front panel:
•
Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing.
•
Follow up the application with warm water rinse.
•
Don’t use abrasives or high alkaline cleaners.
•
Don’t leave cleaners on for long periods, wash immediately.
•
Don’t apply cleaners in direct sunlight or at elevated temperatures.
•
Don’t use scrapers, squeegees or razors.
•
Don’t clean with gasoline.
Compatible Cleaners and Detergents:
•
Formula 409
•
Top Job
•
Joy
•
Palmolive
•
Windex with Ammonia D
To Minimize Fine or Hairline Scratches:
Mild automotive polish applied and removed with a soft, clean cloth will help fill scratches.
Suggested Polishes:
•
Johnson Paste Wax
•
Mirror Glaze #10 Plastic Polish (by Mirror Bright Polish Co.)
•
Novus Plastics Polish #1, #2 (by Novus Inc.)
Maintenance
Page 5-3
Cybex Eagle 11120 Standing Calf Owner’s Manual
Weekly Procedures
1. Check all nuts and bolts for looseness. Tighten as required.
2. Inspect all belts (entire length) for any non-uniformity and wear.
Immediately replace belt if any of the following conditions are present:
Maintenance
Page 5-4
Cybex Eagle 11120 Standing Calf Owner’s Manual
3. Some machines use cables in addition to belts. Inspect all cables for wear or damage and proper
tension. When inspecting cables, run your fingers on the cable, paying particular attention to bends
in the cable and attachment points.
Replace all worn cables immediately. The following conditions may indicate a worn
cable:
•
A tear or crack in the cable sheath that exposes the cable. See Figure 1.
Figure 1
•
A kink in the cable. See Figure 2.
Figure 2
•
A curled sheath. See Figure 3.
Figure 3
•
“Necking”, a stretched cable sheath. See Figure 4.
Figure 4
Maintenance
Page 5-5
Cybex Eagle 11120 Standing Calf Owner’s Manual
4. Inspect bars and handles for wear, paying particular attention to tab area connecting
points.
Replace all worn handles immediately.
5. Inspect snap links for proper latching (indicates wear).
Replace all worn snap links immediately.
6. Inspect for loose or worn grips.
Replace all loose or worn grips immediately.
7. Inspect all labeling for readability. This includes instructional placards, warning and caution decals.
Replace all worn labeling immediately.
8. Inspect all weight stacks for proper alignment and operation.
Correct all improper alignment and operation issues immediately.
9. Wipe Weight Stack Guide Rods clean over entire length. Lubricate with a light coat of medium
weight automotive engine oil.
Yearly Procedures
1. Replace all belts and cables at least annually.
Maintenance
Page 5-6
Cybex Eagle 11120 Standing Calf Owner’s Manual
Environment
Static Electricity - Depending upon where you live, you may experience dry air, causing a common experience of
static electricity. This may be especially true in the winter time. You may notice a static build-up just by walking across a
carpet and then touching a metal object. The same can hold true while working out on your unit. You may experience a
shock due to the build-up of static electricity on your body and the discharge path of the unit. If you experience this type
of situation, you may want to increase the humidity to a comfortable level through the use of a humidifier.
Humidity - The unit is designed to function normally in an environment with a relative humidity range of 30% to 75%.
NOTE: Do not install or use the unit in an area of high humidity, such as in the vicinity of a steam room, sauna, indoor
pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the electronics as
well as other parts of the machine.
Temperature - The unit is designed to function normally in an environment with an ambient
o
o
o
o
temperature range of 50 F (10 C) to 104 F (40 C) degrees.
Storage
Humidity - The unit can be shipped and stored in an environment with a relative humidity range of 10% to 90%.
NOTE: Do not store the unit in an area of high humidity, such as in the vicinity of a steam room, sauna, indoor pool or
outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the electronics as
well as other parts of the machine.
o
o
Temperature - The unit can be shipped and stored in an environment with an ambient temperature range of 32 F (0 C)
o
o
and 140 F (60 C) degrees.
Maintenance
Page 5-7
Cybex Eagle 11120 Standing Calf Owner’s Manual
Maintenance
Page 5-8
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • techhelp@cybexintl.com