User guide and terms of guarantee
Bicycle manufacturer
Development
b’Twin designs and develops product ranges for all purposes. Our multidisciplinary team is driven by a
passion for bikes coupled with technical expertise. B’Twin products are created by our engineers, athletes
and designers.
Innovation
As a leading European manufacturer, we have established an innovative partnership with the B’Twin
research centre so that you can enjoy your passion to the full.
Design
Our design office ensures that our products satisfy your desires, just like B’Twin.
They pay particular attention to ensuring that the technical features, comfort and look of our bicycles are
perfectly suited to their practical use. Modernity, simplicity and passion guide our imagination.
Fatigue test
Just like b'Twin, we are unswerving in testing our prototypes b’Twin :
– more than 250 components tested to select 74.
– more than 50 prototypes tested during test assignments.
– more than 3000 hours of machine tests in our workshops.
2
COMPLIES WITH SAFETY REQUIREMENTS
Thank you for purchasing a B’Twin bicycle
You have just bought a B’Twin bicycle, and to ensure your continuing happiness with it, please read this user guide:
it provides all the information needed to correctly use, adjust and maintain your B’Twin bicycle.
It is important that you keep this guide.
This general guide and manufacturer's guides for each component (derailer, brakes, fork, etc...) can be viewed on www.btwin.com
CONTENTS
CONTENTS............................................................................................................................................................................................................................................................... 3
General warning............................................................................................................................................................................................................................................... 4 Mini bicycle glossary........................................................................................................................................................................................................................ 4
A BICYCLE FOR EVERY PURPOSE, AND ITS LIMITS..................................................................................................................................................... 5 General usage restrictions.......................................................................................................................................................................................................... 5 Storage conditions............................................................................................................................................................................................................................. 5 Types of bicycle and their uses ............................................................................................................................................................................................. 5
RECOMMENDATIONS FOR CYCLING IN COMPLETE SAFETY........................................................................................................................... 6
HOW TO ADJUST YOUR POSITION ON THE BICYCLE................................................................................................................................................ 8
SAFETY CHECKS BEFORE USE................................................................................................................................................................................................................. 9
ADJUSTMENTS AFTER SEVERAL HOURS' USE......................................................................................................................................................................... 10
MAINTAINING YOUR BIKE............................................................................................................................................................................................................................ 10 A - REGULAR MAINTENANCE AND CHECKS............................................................................................................................................................... 11 B - NECESSARY TOOLS..................................................................................................................................................................................................................... 12 C - CLEANING .......................................................................................................................................................................................................................................... 12 D - LUBRICATION................................................................................................................................................................................................................................... 12 E - TIGHTENING TORQUES........................................................................................................................................................................................................... 13 F - REMOVING – REPLACING A WHEEL............................................................................................................................................................................ 13 G - USING QUICK-RELEASE.......................................................................................................................................................................................................... 15 H - MOUNTING THE PEDALS...................................................................................................................................................................................................... 15
I - BRAKING SYSTEM.......................................................................................................................................................................................................................... 16
1 - Using the brakes.................................................................................................................................................................................................................... 16
2 - Checking the brakes........................................................................................................................................................................................................... 16
3 - How should the brakes be adjusted?................................................................................................................................................................ 16 J - USING THE GEAR SYSTEM..................................................................................................................................................................................................... 18 K - ADJUSTING THE DERAILER GEAR SYSTEM.......................................................................................................................................................... 19
1 - Adjusting rear derailer travel..................................................................................................................................................................................... 19 2 - Adjusting front derailer movement.................................................................................................................................................................... 19 3 - Adjusting derailer tension............................................................................................................................................................................................ 19
L - ADJUSTING IN-HUB GEARS ............................................................................................................................................................................................... 20
M- ADJUSTING SINGLE SPEED GEARS.............................................................................................................................................................................. 20
N - ADJUSTING SUSPENSION.................................................................................................................................................................................................... 20
ASSEMBLING ACCESSORIES................................................................................................................................................................................................................ 20
GUARANTEE CHARTER.............................................................................................................................................................................................................................. 22
3
general warning
Like any sport, cycling can cause injury and damage. By using this bicycle, you accept responsibility for this risk. b’Twin cannot accept any
liability if the product is modified by the user. You should know and practice the rules of the Highway Code. Caring for and using your bicycle
correctly are your responsibility and reduce the risk of accidents. Caring for your bicycle correctly will preserve its original usage and safety
features. Cycling, in whatever form, is not without risk. Always wear a correctly fitted and adjusted helmet.
Supplement to the user’s guide:
If your bicycle is equipped with specific components (for example: adjustable suspension fork, hydraulic brakes, frame shock absorbers, ),
your retailer will also give you the individual instructions for them.
Maintenance, adjustment and repair:
To ensure that your bicycle is maintained properly and safely, we recommend that you have it serviced and repaired by an
authorised B’Twin after-sales service provider.
Your b’Twin retailer:
Other than this guide, your main source of information and assistance is your B’Twin store. Your retailer is your first contact for
enquiries relating to your bicycle’s maintenance, adjustment, use and guarantee.
Guarantee:
This guide also contains your bicycle’s guarantee conditions.
NB:
Bicycles and bicycle components change all the time, so it is impossible to produce an exhaustive guide. We recommend that you
consult a b 'Twin technician or retailer should you need further information.
Mini bicycle glossary:
Handlebars
Stem
Saddle
Frame
Seatpost
Seatpost clamp
Brake
Fork
Cogs
Disc brake
Front derailer
Crank
Crankset
Rear derailer
chain
Chain rings
Pedal
Rim
Tyre
The safety parts (front fork, handlebars and handlebar stem, seat post, brake pads, brake shoes and disk brake pads, brake cable outer casing,
hydraulic brake line, calipers, brake disks, brake levers, chain, pedals and cranks, bottom bracket axle and wheel rims) must be replaced with
original parts. Tyres and inner tubes must be replaced with compatible parts.
WARNING: Like any mechanical component, a bicycle is subject to significant stresses and strains. The different materials and components
can react differently to use or to fatigue. If a component's expected life span is exceeded, it may break suddenly, thus risking injury to the
cyclist. Cracks, chips and discolouring in areas subject to great stresses show that the component has exceeded its lifespan and should be
replaced.
4
A BIKE FOR EVERY PURPOSE, AND ITS LIMITS
A mini guide to help you choose correctly! Define your discipline precisely.
General usage restrictions:
Storage conditions
Your bicycle is not designed to be used:
• in sand. • in the water (the hubs and bottom bracket should not
be submerged).
• in a salty environment (e.g.: on the beach).
Your bicycle is not designed to be stored outdoors for
prolonged periods outside. It should be stored in a dry
and heated area (away from frost), away from corrosive
products: sea air (ex: deck of a boat), weedkiller, acids,
solvents, batteries...
Types of bicycle and their uses
MOUNTAIN BIKES
TRAIL BIKES
(BTWIN, TRIBAN TRAIL)
MOUNTAIN BIKES: These are sporty, versatile bicycles, suitable for going off-road and exploring nature. Full
suspension Leisure MTBs are ideal for forest or city riding on good roads. Full suspension Leisure MTBs provide extra
comfort. Sport and Competition MTBs are designed for all terrains. The difference lies in the weight, the quality of the
drive train and the suspension. Full suspension MTBs will allow you to ride for longer with less tiredness and more
control. They are ideal for descents, but are also comfortable on technical climbs. This bicycle, and particularly its
braking system, is designed for a maximum load of 100kg. For example, for a bicycle and accessories weighing 13 kg
with 5 kg luggage, the maximum user weight is 100 - 13 - 5 = 82 kg.
TRAIL BIKES: This is the ideal compromise between the town bike and the mountain bike. It is comfortable and
well-equipped, and is ideal for riding alone, as a family or with friends, on small country roads or off-road trails. The
wheels are narrower than an MTB's wheels and may be of a greater diameter ; so it is more comfortable on tarmac
roads. It is ideal for bike rides. This bicycle, and particularly its braking system, is designed for a maximum load of
100 kg. For example, for a bicycle and accessories weighing 13 kg with 5 kg of luggage, the maximum user weight
is 100 - 13 - 5 = 82 kg.
CITY BIKES:
ELOPS OR CITY: Fully equipped and comfortable, it is ideal for getting around in total safety on town and city roads,
in the middle of traffic. You stay clean thanks to its mudguards and chain guard. It is the supreme city bike.
TRIBAN ROAD: A bike designed for urban and peri-urban road sports. Positioned between the racing bike and the
traditional town bike, this responsive bike is designed for regular sporting middle distance rides on the road. This
bicycle, and particularly its braking system, is designed for a maximum load of 100kg. For example, for a bicycle and
accessories weighing 13 kg with 5 kg of luggage, the maximum user weight is 100 - 13 - 5 = 82 kg.
CITY BIKES
(ELOPS, CITY, TRIBAN road)
FOLDABLE BIKES: Specifically designed to cope with storage problems, the foldable bike is the ideal bike for getting
around town. It is a sturdy, multi-purpose and well-equipped bicycle. Easy to store: the foldable bike will take you
where you want to go, "door to door ". Its compact size makes it easy to store at home or at the office reducing any
risk of theft. You'll forget it's there. Multiple transport modes: the foldable bike is designed to help you getting around
town over long distances as a complementary mode of transport to the car, train, public transport allowing you to
reduce any breaks in your route and save time. " the problem with public transport is that it never takes you exactly
where you want to go ". Journey: the foldable bike will follow you everywhere: caravan, boat, boot of a car. Stored in
a small area, it's the ideal companion for your itinerant leisure activities.
FOLDABLE BIKES
ROAD BIKES: This is a light bike for fitness or competition use. The frame geometry is suited to each purpose:
fitness objective: stay in shape by using a light bicycle and gears adapted to your power, and sport target: discover
cycling alone or in groups on hilly rides. This bicycle’s frame geometry and components will give you a good ride,
competition target: take your training to a new level to work on your physique, and take part in competitions using
equipment approved at the highest level of competition. This bicycle, and particularly its braking system, is designed
for a maximum load of 100kg). For example, for a bicycle and accessories weighing 13 kg with 5 kg of luggage, the
maximum user weight is 100 - 13 - 5 = 82 kg.
Road bike
The BMX/SUBSIN: specifically designed for acrobatic use. “Street” for stunts in town or a skate park. “Dirt” for stunt
jumps on dirt tracks. “Flat” for stunts on the ground. “Race course” for off-road circuits with bumps. We recommend
that you carefully identify your discipline before taking the plunge! This bicycle, and particularly its braking system,
is designed for a maximum load of 100kg. For example, for a bicycle and accessories weighing 13 kg with 5 kg of
luggage, the maximum user weight is 100 - 13 - 5 = 82 kg.
BMX/SUBSIN
child's bike
(14’’, 16" to 24“)
The 14" CHILDREN'S BIKE“ : A bicycle designed to allow children to pedal in complete safety. Easy to use,
hardwearing and fun, this upgradeable bike is designed for children aged 3 to 5 (90-105 cm), and for a maximum
user weight of 33 kg. For example, a bicycle weighs 8kg, the maximum user weight is 33-8 = 25kg. Because it is a
child's bike without any lighting, this product should not be used on the road.
CHILDREN’S BICYCLE (16” To 24“): Designed for children’s very specific needs. Whether your child is just learning
how to pedal or is already very comfortable on a bicycle, this bike is for all uses, by age group. It is a solid, easy to use,
fun and well-equipped bicycle. It is the ideal partner for learning and having fun in complete safety. These bicycles,
and particularly their braking systems, are designed for a maximum weight of 45kg for the 16", 55kg for the 20"
and 70 kg for the 24". For example, for a 16” bicycle and accessories weighing 10 kg carrying 1 kg of luggage, the
maximum user weight is 45 - 10 - 1 = 34 kg.
5
RECOMMENDATIONS
FOR CYCLING IN COMPLETE SAFETY
Here are a few rules for responsible trail riding:
• Avoid leaving visible tracks
• Do not frighten animals
• Keep control of your bicycle
• Look in front of you
• Always let others pass
• Take all your rubbish with you
•Always carry out a thorough check before riding. Read the
" safety checks before use section ».
•Always wear a helmet when you ride to protect your head in
the event of a fall.
•Ride with both hands on the handlebars.
•Ride in the direction of the traffic, never against it.
•Never hold on to a car or any other vehicle.
•Control your speed, avoid moving from side to side.
•Carrying baggage may reduce your visibility or control of the
bicycle and cause you to fall.
•Respect the local Highway Code, particularly with regard to
lights and bicycle bells and horns.
WARNING! when riding with children
•b’Twin recommends that helmets are worn and strongly
advises that child seats and all frame accessories are fitted
by qualified, experienced technicians. If you intend to fit
a child seat yourself, we recommend that you check with
our retailers that baggage racks and child seats are safely
compatible.
•Be careful when riding with a child seat, as it adds weight
to the rear and raises the bicycle’s centre of gravity, making
balance and turning more difficult.
•Children must always wear a helmet when riding in a child
seat or in a trailer. Please note that wearing a helmet is a legal
requirement in many countries.
•Wheels attract children's attention and present a serious
risk to young children's fingers! If children place their
fingers between the spokes or between the chain and the
chain rings, they risk trapping their fingers and/or injuring
themselves. With children’s bicycles, responsible adults must
ensure that the child knows how to use the bike, especially
the brakes.
WARNING! Two people should never ride on a bicycle
(except tandems)
• Never ride at night or in bad weather without lights. You
must be visible to motorists and motorcyclists :
- Wear light, reflective clothing, and turn your front and rear
lights on.
- You must have a light and a reflector at the rear of your
bicycle.
- You must also have a light and a reflector at the front of your
bicycle.
- Side reflectors must be placed on the wheels.
•When cycling in the rain or on wet roads, be careful
because braking distances can increase and grip decreases
significantly.
•Wear protective equipment and clothing, such as gloves and
glasses.
•Do not wear loose clothing which may get caught in the
wheels.
Maintaining and controlling your bicycle.
The frame, the forks and all the components must be regularly
checked by our b 'Twin After-Sales Service team to detect the
signs of wear and/or potential deterioration (cracks, corrosion,
damage...).
These are important safety checks which help avoid accidents
and physical injury and ensure the lasting condition of your
bicycle.
NB: All our bicycles are sold with front and rear lights, as well
as rear reflectors and side reflectors fitted to the wheels).
Riding on paths: responsible behaviour and code of good
conduct.
Do not take access to paths for granted. The way you behave
when you next ride your bicycle will influence how accessible
paths will be are in the years to come:
- Stay on the roads.
- Be respectful to pedestrians and horse-riders.
- Keep skidding to a minimum.
- Respect flora and fauna.
- Avoid muddy areas.
6
STOP
Warning:
- MTB descents should be practiced safely.
- Ensure that the bicycle is suitable for the purpose (Descents, Cross-country, extreme Freeriding, etc).
- Ensure that the bicycle is in a perfect state of repair.
- To minimise the risk of accidents: wear a helmet, wear suitable protection, control your bicycle and… be careful!
Fitting lights: (does not apply to dynamo-type lights)
Compatible with
upright handlebars.
Diameter:
19 mm to 32 mm.
Compatible with seat
posts or seat stays.
Diameter:
19 mm to 32 mm.
Front light
Rear light
A-B-C: Assembly
Assembly
For best fitting, try to use the first hole in the strap.
- The first hole is for fitting to the seat post.
- The second hole is for fitting to seat stays.
D: Removal
Press the reflector (1) to push the light forwards (2).
Position the rear light horizontally using the
adjustment wheel.
Replacing the batteries:
Replacing the bulbs
When the red wear indicator lights up, change the batteries.
Batteries required: Two 1.5 Volt LR14 alkaline batteries.
To open, press on one of the chrome-plated strips (1)
and open by turning the light (2). Battery direction
is shown on the bulb holder and on the inner contact.
Bulb required: 2.4 Volt 0.5A Krypton.
Some products may be equipped with different
but similar lighting.
7
Fitting dynamo-type lights
Hub dynamo: Before removing the front wheel, disconnect the
dynamo’s electric cable.
Replacing the bulbs:
Bulbs required:
• 6 Volt / 2.4 Watt Krypton type bulb for Elops 3 and Elops 5.
6 Volt / 2.4 Watt halogen bulb for the b’Twin Pack and Elops 7.
HOW TO ADJUST YOUR POSITION ON THE BIKE
Measure your height
Adjust your bicycle
Refer to your settings charts
for my bike
16“
S (cm) Hs (cm) Hg (cm)
105-109
48.5
110-114 37.5
49
115-120
49.5
A
B
Elops
S (cm) Hs (cm) Hg (cm)
155-159 55.5
160-164
58
165-169
60
170-174 62.5
+12
175-179 64.5
180-184
67
185-190 69.5
C
For more precise
adjustment of your
bike, go to the b'Twin.
com website
Directions for use:
Refer to the charts appended to the end of these instructions p 23.
Adjusting the seat:
The minimum seat height is the height when the seat is moved down as far as it will go and once
the clamp is locked.
Practical information Depending on the terrain you are travelling on, seat height
can be modified:
- On flat ground or when climbing, the seat should be in a high position for greater efficiency.
- When travelling downhill, the seat should be slightly lowered to improve bicycle control and to
make it easier to get over obstacles.
PLEASE NOTE INSERTION LIMIT!
For your safety, the seat should not be set further than the following warning on the
seat post: minimum insertion.
8
Adjusting handlebar height:
max
Quill stem:
Please note the quill stem insertion limit: For your safety, the stem
should not be set further than the following warning on the stem: " min.
insertion ».
min. insertion
Headset stem:
All MTBs fitted with aheadset stems are sold with setting rings. The
handlebar height suggested in the shop is the highest. If you would prefer to raise the handlebar position, you will need to
choose a higher stem.
Adjusting aheadset stems on your bicycle:
To reduce the height you need to use appropriate tools (T-bars 5 or 6 depending on the model - see tools chapter).
- Completely unscrew screw A, then the two B screws in the stem.
- Remove the stem.
- Take 1 or more setting rings.
- Replace the stem.
- Replace the setting rings above the stem.
- Tighten up screw A and tighten the B screws.
Checking that aheadset stems are properly fitted to your bicycle:
To check the adjustment of your stem, close the front brake and rock forwards and backwards on
your bicycle.
If you feel any movement in the steering system, tighten up screw A.
Second check: lift the front of the bicycle off the ground and turn the handlebars from side to
side.
If it's hard to turn the handlebars, unscrew the screw A.
If this procedure seems too complex, please ask the staff in the workshop at your nearest shop.
Checking that the handlebars are properly mounted in the stem.
On Elops (1, 3, 5 and 7), b’Twin Pack and BMX bicycles, the handlebars are set at a significant angle. The angular position of the
handlebars should not be modified by more than 10° compared with the assembly position (see pictures below).
SAFETY CHECKS BEFORE USE
•Adjusting the seat post and seat: check that the whole bicycle is solidly assembled and that the seat is solidly clamped in the frame, respecting the
minimum insertion point indicated on the tube.
•Tightening the stem: before each use, check that the stem is properly adjusted using appropriate tools (see tools chapter) and tighten to the torque
indicated. Check the value in the stem/steering system torque table.
•Tyre inflation, dimensions and mounting direction: inflate your tyres to the correct pressure, referring to the pressure range indicated on the side of
the tyre by the manufacturer; your tyre’s resistance to wear depends on it. Mount the tyre in the direction indicated on the side (the arrows indicating
the rotation direction).
•The assembly and tightening screws should be tightening according to the recommended torque settings. A screw or nut that is too tight may
elongate and lose its shape. A screw or nut that is not tight enough may move and wear out through fatigue. In both cases, this may cause the screw
or nut to break suddenly, resulting in a loss of control and the user falling.
•WARNING: Insufficient tightening of the screws between the stem and the fork, the handlebar tightening screws or the screws fastening the
handlebar extensions, may compromise the steering and lead to a loss of control and the user falling. Put the wheel between your legs and your
hands on the grips. Try to twist the entire handlebar/stem assembly around the axis of the fork. If this handlebar/stem assembly moves while the
wheel remains stationary or if the handlebar extensions turn around the handlebars, the fastening screws are not sufficiently tightened.
9
STOP
Before every ride you must check that
there is no movement between any of
the different assembled parts!
Rotation direction
Note that 14.5 PSI = 1 BAR and 1 BAR = 1kg/cm2 = 100,000 Pa
• Fitting the wheels: Read the section on using quick connectors.
• How front and back brakes work: Refer to the chapter on the braking system entitled “checking the brakes”.
• Fitting the pedals: Refer to the chapter entitled “mounting the pedals”
• How the lights work:
The lighting system is part of your bicycle’s safety system and must be fitted to your bicycle. Check that your
lighting systems are working and that the batteries are sufficiently charged before setting off. Empty batteries
contain metals that are harmful to the environment (Hg: mercury, Cd: Cadmium, Pb: lead) : they are collected in our
stores to be treated appropriately, do not dispose with household waste. Batteries should be collected separately.
The "crossed-out bin" symbol means that this product and the batteries it contains should not be disposed of
in household waste. They must be separated and recycled specially. Take the batteries and unusable electronic
product to an authorised collection area for recycling. Recycling your electronic waste will protect the environment
and your health.
STOP
STOP
STOP
Warning about automatic pedals:
Automatic pedals are tricky to use and require a period of familiarisation to avoid falling off: engage and disengage your
shoes in the pedals before setting off. The interface between the cleat and the pedal can be affected by a number of
factors including dust, mud, lubrication, spring tension and general wear. When engaging and disengaging, check how
the mechanism works and familiarise yourself with how the pedals feel.
Warning about the frame and fork suspensions:
Refer to the instructions supplied with this manual. At every ride you must check that there is no movement between any
of the different assembled parts. If there is, only consult qualified
personnel and/or your nearest shop, so that they can carry out the
necessary adjustments.
Warning about fork direction (position, brake, etc…):
ADJUSTMENTS AFTER
SEVERAL HOURS OF RIDING
Some parts of your bicycle will require slight modification after 2 to 3 hours’ use, mainly in order to make final adjustments to the
components. Derailer cable tension is to be set: the housings will settle down, requiring new derailer and brake tensions. (See
chapter on adjusting derailer tension). With single-speed bikes, pedaling may seem difficult at first. This is completely normal,
and after a few hours’ use pedaling will become easier: the chain loosens naturally. After your first use of a bike with a 6-piece
bottom bracket, you will need to tighten up the bottom bracket. To do this, please consult a qualified person and/or our technical
workshops.
taking good care of your bicycle
Your bicycle needs a minimum amount of maintenance and regular services. How often it needs to be serviced depends on
bicycle type (city, racing, mountain), how often you use it, and how you use it. Your bicycle’s maintenance depends on the use
you make of it:
•City and recreational bikes, racers and BMX require regular maintenance: Oil the chain regularly, brush the cogs and chain rings,
periodically place a few drops of oil in the brake and derailer cable housings and remove dust from the brake pads.
•MTBs should be cleaned after riding on muddy or dusty terrain: frame, wheels, chain, chain rings and cogs; then lubricate the
chain using the oil specifically designed for bike drive trains. Should you detect any damage to parts of your bicycle, please
replace the parts concerned.
•Regularly check the tyres and make a note of wear, cuts, cracks, pinching. Replace the tyre if necessary. Check the rims and make
sure there is no excessive wear, loss of shape, knocks, cracks. Consult your retailer if the rim is damaged.
10
A
REGULAR MAINTENANCE AND SERVICING
Here is an idea of the type of maintenance to carry out on your bicycle, beginning at the date of purchase: how often you perform
the maintenance may significantly increase if you use your bicycle intensively in hostile environments (mud, sand, water, etc).
3 months
• Full tightening-up of the bicycle.
• Tightening and/or alignment of wheels.
• Drive train adjustment (if necessary).
CHILDREN
6 months
years
MTB
FOLDING BIKE
ROAD
• Change drive train (chain rings, chain and
freewheel).
• Change tyres and inner tubes.
Bikes with suspension: Maintaining forks and shock absorbers, consult the
Decathlon Workshop.
• Lubrication.
• Change brake pads or disk brake pads.
CHILDREN
2
CITY
ROAD
• Change bottom bracket.
• Change cables and brake and derailer housings.
MTB
1 year
HYBRID BIKE
• Lubrication.
• Change brake pads or disk brake pads.
MTB
1 year
BMX/SUBSIN
BMX/SUBSIN
HYBRID BIKE
• Change bottom bracket.
• Change cables and brake and derailer housings.
CHILDREN
BMX/SUBSIN
Hybrid bike
CITY
FOLDING BIKE
• Change drive train (chain rings, chain and
freewheel).
• Change tyres and inner tubes.
CITY
FOLDING BIKE
Warning: Intensive use and/or use in extreme conditions (water, mud, etc) may greatly reduce the lifespan of
components subject to wear and tear (ball bearings, chain, etc) thus requiring more frequent maintenance.
11
B
TOOLS REQUIRED
08
09
10
13
14
In order to assemble, adjust and repair your bicycle correctly, you will need to have some basic tools:
15, 14, 13, 10, 9 and 8mm spanners
4mm Torx
Flat
Phillips
Set of Allen
key
screwdriver screwdriver
keys
Oilcan
These tools are essential for carrying out the different stages of bicycle assembly. You will find them useful for making all the
adjustments described in this manual.
Advice:
When riding and trekking by bike, we recommend you have at least the following equipment:
• a chain breaker and a master link adapted to the bike's original chain.
• an inner tube compatible with your tyres and wheel rims.
• a tyre removal kit.
• a multifunctional tool featuring at least the tools listed above.
• a bicycle pump.
C
CLEANING
Your bicycle can very easily be cleaned with a sponge, a hose or soapy water. The gear system components can be cleaned with a
small brush.
BE CAREFUL with high pressure cleaning systems!
Most importantly, do not use a steam jet: grease may liquefy inside mechanical components, your bicycle will be immobilised
indefinitely, and ball bearings and the gear system will completely seize up. Also avoid overly powerful jets, which may damage the
paintwork on your frame : do not point the jet at any mechanical parts. To avoid corrosion of the components, dry any remaining
water and re-lubricate moving parts (derailers, chain, brake and derailer cables).
D
LUBRICATION
It is necessary to lubricate components to maximise your bicycle's performance and lifespan, and to avoid component corrosion.
Use vaseline-type oil for gear cables and gear system components. For the chain, it is better to use a special oil. Immediately after
washing: dry and oil gear system components (derailer, shifter), suspension parts, brake levers, caliper and brake mounts and
the chain. Check the chain and replace it if necessary (see the section entitled “maintenance checks "). For good waterproofing,
sufficiently grease the seat post, the quill stem and the headset. Cartridge-style bottom bracket shells do not need maintenance:
they are sufficiently watertight to keep them greased for the entire lifespan of the bracket. However, to avoid noises it may be
necessary to grease the points where the frame and the bracket meet.
Advice:
We recommend that you use OUR SELECTION: Degreasing kit and Teflon oil, grease.
STOP
Warning: All these operations should be undertaken regularly if you use your bicycle in a salty environment and before
prolonged storage.
12
E
TIGHTENING TORQUES
Type of bicycle
Stem/
Handlebar
Stem/fork
Saddle/
seat post
Seat post/
frame
Front wheel/
frame
Back wheel/
frame
Pedals/ cranks
CHILDREN
(14“, 16“)
NO
APPLICABLE
18
NO
APPLICABLE
Quick-release or
10/12
22/30
22/30
30/45
1 18mm screw 2
12mm screws
24
Quick-release
or 8 +/- 1 Nm
22/30
or quick-release
22/30
or quick-release
30/45
20
16 pivot system
Quick-release
or 8/10
35/40
35/40
30/45
16 b’Twin 3: 24
Quick-release
Quick-release
22/30
or quick-release
30/45
24
Quick-release
or 8/10
28
22/30
or quick-release
30/45
16mm screw 2
JUNIOR (20”, 24“) 112mm
screws
BMX/SUBSIN
10
12
CITY AND
COUNTRY **
1 16mm screw
2 12mm screws
4 7mm screws
16
1 18mm screw
2 12mm screws
13
22
LEISURE MTB
7
7
17 RR 5.1: 24
Quick-release
or 8/10
Quick-release
Quick-release
or 22/30 nut
30/45
SPORT MTB
6
7
17/24
Quick-release or
8/10
Quick-release
Quick-release
30/45
COMPETITION
MTB
5
7
8
Quick release
or 8/10
5/7 carbon frame
Quick-release
Quick-release
30/45
FITNESS AND
SPORTS ROAD
BIKE
6
6
15
6/8 aluminium
frame
Quick-release
Quick-release
5mm allen screw: 14 Nm
8mm allen screw: 40 Nm
10mm allen screw: 45 Nm
COMPETITION
ROAD BIKE
5/6
6/7
15
5/7 carbon frame
Quick-release
Quick-release
5mm allen screw: 14 Nm
8mm allen screw: 50 Nm
FOLDING BIKE
6/9
20
20
Quick-release
25/35
25/35
35/40
18
24
13
35
35
30/45
(b’Twin, Triban Trail)
3
URBAN Elops 5
7
B’COOOL
F
18
17
Quick-release
REMOVING – REPLACING
1 - Quick-release wheels
Removal
• Open the caliper (see the brakes section).
• Open the quick-release lever (see the following section on using quick-release).
• For the front wheel: unscrew the adjusting nut then remove the safety washer.
• Remove the wheel.
CLOSED position
Re-assembly
•P
lace the wheel in a central position between the frame
dropouts and the fork.
• If necessary, replace the safety washer.
• Tighten the adjusting nut.
• Close the quick-release system.
• Close the caliper (see the brakes section).
Force adjustment
Open position
13
(*) For assemblies using quick-release, please see chapter entitled “Use of quick-release”.
(**) Tightening torque of the handlebar stem incline screw = 18 Nm
• Tightening torques for the assembly of the following components (in Nm) (*):
2 - Traditional (non quick-release) wheels
Removal
CLOSED
• Open the caliper (see the brakes section).
• Undo the wheel nuts using a suitable spanner.
• For the front wheel: where applicable, remove the safety washer.
• Remove the wheel.
Re-assembly
• Place the wheel in a central position between the frame dropouts and the fork.
• If necessary, replace the safety washer.
• Tighten the nuts to the appropriate torque.
• Close the caliper (see the brakes section).
OPEN
Comment on the rear gear wheel: Position the chain on the smallest cog to
make it easier to replace the wheel.
3 - Wheels with a hub brake
Removing and replacing this type of wheel is difficult, so we recommend that you
consult one of our technical workshops. Nevertheless, you may follow the procedure
below at your own responsibility:
Removal
• Disconnect the brake as in the diagram.
• Undo the wheel nuts using a suitable spanner.
• Remove the wheel.
Re-assembly
• Place the wheel in a central position between the frame dropouts and the fork.
• Tighten up the nuts.
• Reconnect the brake as in the diagram.
4 - Wheels with a backpedal brake
Removing this type of wheel is difficult, so we recommend that you contact one of
technical workshops. Nevertheless, you may follow the procedure below at your own
responsibility:
Removal
•Disconnect the frame dropout (1) by unscrewing the nut (2) using a suitable
spanner.
•Then follow the instructions for "Non quick-release WHEELS”.
Re-assembly
•Reconnect the frame dropout (1) by unscrewing the nut (2) using a suitable
spanner to a torque between 6 and 9 Nm (inclusive.
•Then follow the instructions for "Non quick-release wheels”.
Wheels with an internal gear hub
Removing this type of wheel is difficult, so we recommend that you contact one of
technical workshops. You can, however, find fitting and removal information on the
website btwin.com.
IMPORTANT: Before using your bicycle, ensure that the wheel is correctly mounted.
14
Safety washers HUB
Nut
G
USING QUICK-RELEASE
Blocking them maintains the wheels in position inside the frame and fork. In order to prevent it coming loose, it is necessary
to turn the adjusting nut (1) such that the closing force of the release lever (2) is at least 12 daN (about 12 Kg). To increase the
closing force: turn the adjusting nut clockwise (anticlockwise to reduce the force).
Please note: in case of doubt, consult one of our in-shop technicians.
CLOSED
CLOSED
OPEN
OPEN
Adjustment screw
1/ Set the adjusting nut
H
STOP
2/ Activate the quick-release
lever (strain 12kg)
3/ It’s finished!
ASSEMBLING PEDALS
Warning: Refrain from trying to tighten the pedals by hand, use a suitable spanner.
1/ Identify your pedal: Check the letter on the pedal: " L " or " R ".
2/ The pedal marked “R” is the right-hand pedal. Turn it clockwise to attach it to the crank.
3/ The pedal marked “L” is the left-hand pedal. Turn it anticlockwise to attach it to the crank.
4/ Adjusting shoe and pedal clamping systems: Please see your manufacturer's instructions.
Minimum distance D
D>89 mm for road and children’s bicycles
D>100 mm for mountain, City and trekking bikes
Please note: when replacing your pedals, wheels, tyres, mudguards or cranks, the minimum clearance between the edge of the
wheel or mudguard and the pedal spindle must be greater than the distances indicated above.
15
I
BRAKING SYSTEM
1 - Using the brakes
To slow the bicycle down or stop it: use the back brake first and then lightly and gradually use the front brake. An overly rapid and
excessive braking movement may cause the front wheel to jam and cause a dangerous fall.
Using disk brakes:
After braking, the disks and calipers may become very hot and cause burns in the event of contact. After braking, wait 30 minutes
before touching the brake or caliper.
Please note: Braking distance increases in wet weather.
2 - Checking the brakes
Before using the bicycle, check that the brakes are working correctly: • When fully pressed, the brake levers must not touch the
handlebars. • Brake cables and housings must not be damaged. • When adjusting the cable, the tightening torque to use is
between 5 and 7 Nm. (cable to caliper assembly).
NB: if one of these conditions is not fulfilled, contact one of our technicians, who will return the system to normal.
STOP
Warning
The rims, disks and pads must never be treated with a lubricant or another greasy substance. If necessary, clean using an antistatic polish. You are advised not to use solvents (which may damage the markings and the paintwork).
For disk brakes and road bike brakes, consult the instructions in the manufacturer’s guide for any modification or " contact your
nearest workshop ".
For the following types of brake:
V-Brakes, the metal pipe of the brake
cable should be completely inserted into
its housing on the caliper.
Cantilevers, the bridge cable with
quick-disconnect fastener must be
correctly mounted.
Calipers,the brake lever spacer must
be in the closed position.
Mechanical or hydraulic disc:
You should be careful when using this type of brake, which requires a bedding-in period of around 30-50 km (depending
on type) to reach their optimum level of performance.
3 - How should the brakes be adjusted?
Brake pads
1/Check the pad is aligned with the edge of the rim.
2/ Check the distance of the pads from the rim (1 to 3mm for optimum braking).
3/ Always distance the rear of the pads slightly from the rim.
16
STOP
Warning
4/ Check that the V-Brake or Cantilever calipers are symmetrical.
Check that the “left and right” caliper return springs are balanced as illustrated below:
ALUMINIUM TUBE
SCREWDRIVER LESS
TENSION
TENSION
SPRING
ADJUSTMENT SCREW
MORE TENSION
SYMMETRICAL SPACE
CANTILEVER
SIDE PULL
HANGER BOLT
HANGER
CABLE
SAFETY HOOK
POSITION
CABLE
PINCH BOLT
Nut
PULL THE CABLE
PULL THE CABLE
rim
Adjusting cable tension
The case of V-Brake or Cantilever or Roller Brake type brakes
Brake maintenance
In order to maintain your bicycle’s braking performance, it is important
to perform maintenance on the braking system at the intervals
described in the chapter entitled “regular maintenance and checks”:
•Replacing worn disk brakes or pads: the surface markings are no
longer visible or the metal structure is under 2mm from the rim or
from the disk.
•The position of mechanical disk brakes must be adjusted regularly as
they wear.
•Replacing brake cables and housings.
•Cleaning hydraulic brake circuits.
Brake lever:
Back brake
Front brake
WARNING: Brakes
are reversed in certain
countries (India, China,
UK).
Back brake
Front brake
Caliper brakes
(U-type)
Maintaining Roller Brake brakes
The greasing of " Roller brake " type brakes should be checked every
year by a specialist. The type and quantity of grease affect braking
power.
The wear of " Roller brakes " is measured by a tool not sold with the bike
and available in store.
17
IMPORTANT: This safety procedure is difficult, so it is better to contact one of our technical workshops to
carry out this type of procedure. Nevertheless, here are a few pointers for users who wish to carry out the
procedure themselves.
Maintaining disk brakes
There should be no grease or oil on disk break pads, it may seriously reduce the efficiency of braking. Before and after each ride,
check that there are no leaks in the hydraulic circuit and the wear on brake pads. Entrust maintenance of the hydraulic circuit to
the Decathlon Workshop. Refer to manufacturer's guides, available on www.btwin.com, to replace brake pads.
Replacing brake pads.
1/ Open the calipers.
2/ Remove the pad using a suitable spanner (Allen key or spanner depending on the model).
3/ Replace the pad, being careful to follow the assembly sequence of washers and spacers carefully.
4/ Tighten up the pad using a suitable spanner, using a tightening torque of between 6 and 9 Nm.
NB: some pads have a mounting direction: the arrow should face the wheel’s rotation direction when the bicycle is moving
forwards.
Replacing disk brake pads:
Replace the worn parts with the correct replacement parts obtained from qualified sources.
Replacing hub brakes:
Replace the worn parts with the correct replacement parts obtained from qualified sources.
Rim wear:
EA
R
EC T TO W
BJ
SU
B
C T TO W
JE
R
EA
Warning to users:
Bicycles with brakes which connect the surface of the rim to the braking system are subject
to wear of the rim wall at the braking surface, as a result of the braking forces and the friction
suffered by the rim at this surface.
We recommend that users pay particular attention to this wear, because a reduction in the
thickness of the rim wall can cause tyre maintenance defects and injury.
Regularly check that the internal or external surfaces of the rims show no signs of cracking or
wear.
Do not use wheels showing signs of advanced wear of the rim's braking surface.
SU
Can be found on this type
of rim.
J
USING THE GEAR SYSTEM
Changing gear: continue to pedal but not too hard, and move the gear shifter (lever or rotating shifter) until the chain is in place
on the selected chain ring or cog.
Each position of the shifter corresponds to a chain position on the cogs.
• If the chain does not move up onto the cog easily: you can try "overshifting" by pushing the lever slightly beyond position
without moving it into the next position.
=> If this does not work: you will need to adjust the cable tension (cf. chapter " adjusting the gear system »).
• If the chain does not move down quickly, see the chapter entitled “ adjusting the gear system ". The chain should move smoothly
between cogs.
Chain ring
STOP
Warning:
In order that the gear system functions correctly
and not to shorten the lifespan of its parts (chain,
freewheel, pedals):
•Avoid heavy, aggressive gear changes.
•Avoid crossing the chain (by using the large cog and
the large chain ring or the small cog and the small
chain wheel).
•If the chain is crossed (Diagram 2), it may be in
contact with the front derailer.
Cog
18
K
ADJUSTMENT OF TENSION AT DERAILER
These procedures are also difficult: we recommend you
consult one of our qualified technicians.
Frame bolt
NB: Problems when changing gear are very often linked to
the derailer cable tension; adjusting the derailer travel is
much less common.
Derailer end
stop
H stop screw
1 - Adjusting rear derailer travel
To prevent the chain jumping off the cogs (in the wheel
spokes or between the rear dropout and the cogs), it is
important to adjust the derailer travel using the H and L
stops:
•Screw H enables the lower stop to be adjusted (small
cogwheel) : untightening this screw enables the chain to
position itself to the outside of the small cogwheel.
•Screw L enables the lower stop to be adjusted (large
cogwheel): untightening this screw enables the chain to
position itself to the outside of the large cogwheel.
L stop screw
Cable bolt
washer
Frame bolt
2 - Adjusting front derailer movement
Adjusting the outer stop
By turning the inner screw of the front derailer in direction A,
the derailer range moves away from the smallest chain ring;
by turning it in direction B, it moves towards the large chain
ring. Then adjust so that the clearance between the chain
guide outer plate and the chain is 0 to 0.5mm.
Adjusting the inner stop
By turning the outer screw of the front derailer in direction
A, the derailer range moves towards to the smallest chain
ring; by turning it in direction B, it moves away from the
large chain ring. Then adjust so that the clearance between
the chain guide inner plate and the chain is between 0 and
0.5 mm.
INNER STOP ADJUSTING
SCREW
OUTER STOP ADJUSTING
SCREW
Chain guide outer
plate
Chain guide inner
plate
Chain
Chain
3 - Adjusting derailer tension
Adjusting the cable tension creates a link between a position on the gear lever and a position in the gear system. Unscrew or
tighten the cable tension screw at the lever or at the rear of the derailer so that each lever position corresponds to a cog:
=> If the chain does not move down every time you shift the lever:
• loosen the cable by turning the cable tension adjusting screw clockwise.
=> If the chain does not move up every time you shift the lever.
• tighten the cable up by turning the cable tension adjusting screw anticlockwise.
19
L
ADJUSTING IN-HUB GEAR SHIFTERS
(NEXUS SHIMANO-type)
Refer to the component guide available on www.btwin.com, for the adjustment of in-hub gear systems.
M
SETTINGS SINGLE SPEED GEARS
(SPECTRO SRAM-type)
For single-speed bikes or bikes with integral gear shifters, you will need to have the chain tension checked (it loosens over time).
Excessive tension can impair performance and reduce its lifespan (hard pedaling).
Insufficient tension can cause the chain to come off frequently. Read the section on single-speed bikes carefully.
A correctly adjusted chain has a maximum vertical travel of 1cm. You adjust the tension by moving the rear wheel forwards or
backwards in the frame dropouts.
1 cm
N
ADJUSTING SUSPENSIONS
Refer to fork and suspension adjustment settings recommended by the supplier, for the NEUF system, refer to the specific guide
for the NEUF system attached to this guide and available in the Menu, or on www.btwin.com. For other models, consult the
supplier guide for components on www.btwin.com
ASSEMBLING ACCESSORIES
We recommend that you follow the specific assembly instructions supplied with the accessory.
STOP
Warning
•Check with a b’Twin retailer that accessories to be fitted to your bicycle are compatible with it b’Twin.
•Check that all the elements of your bicycle work correctly when the accessory is fitted. The bicycle may respond differently when
accessories are fitted.
•Be particularly vigilant with accessories which may hinder wheel rotation, interact with a suspension frame in full travel or
change the shape of the frame using tightening devices.
•Non-suspended MTBs with a disk brake system: - are only compatible with child seats that attach to the frame's vertical tube,
-are not compatible with luggage racks.
•The child seat may significantly affect your bicycle's stability. It is not permitted to attach a child seat directly to the bike's seat
post.
Check that under no circumstances will any part of the child's body or clothing (laces, safety
belts, etc.) come into contact with any of the bicycle’s moving parts as this may cause injury to
the child or an accident. It is recommended that child seats are fitted to bicycles with protective
mud guards so that the child's feet or hands do not get trapped between the spokes of the wheel.
Similarly, it is best to use a seat cover or a seat with internal springs so that children do not trap
their fingers in the springs.
20
•A kickstand is designed to support a non-loaded bicycle: never leave a child on a bicycle supported on a kickstand.
•There are holes on your frame for attaching a bottle-carrier. If there aren’t, use add-on attachments, fitted using an elastomer
strip available in our range of detachable parts.
•For rotors and pegs, see the assembly instructions supplied.
•You must not add bar-ends, unless the bicycle is sold with them already mounted.
•The use of aerodynamic add-ons on your handlebars can increase braking distances and a loss of stability on bends.
•The maximum authorised weight of baggage and accessories (child seat, panniers, etc) depends on the weight of the user
and the maximum authorised weight of the bike. Baggage weight should in no circumstances be greater than the maximum
indicated in your accessory’s instructions.
•To mount and set the tightening torques for aerodynamic add-ons (such as triathlon handlebars), see specific instructions.
•When adding stabilisers, see the manufacturer's instructions for mounting and adjustment guidance.
Compatibility of b’Twin accessories with b'Twin bikes:
Baggage (saddlebags, panniers, luggage
racks...)
Child seat
Bicycle name
Front
Rear
Front
Rear
24 -> all)
NOT ALLOWED
NOT ALLOWED
AUTHORISED
AUTHORISED
24’’ FS
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
b’coool
NOT ALLOWED
NOT ALLOWED
AUTHORISED*
AUTHORISED**
BMX (all)
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
b’Twin (all)
AUTHORISED
AUTHORISED
AUTHORISED
AUTHORISED
b’Twin 7
AUTHORISED
NOT ALLOWED
AUTHORISED
AUTHORISED
Elops 3, Elops 5
AUTHORISED
AUTHORISED
AUTHORISED
AUTHORISED
Elops city, Riverside
NOT ALLOWED
NOT ALLOWED
AUTHORISED
AUTHORISED
Road bike
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
Full suspension MTB
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
Leisure MTB / Sports nonsuspended
NOT ALLOWED
AUTHORISED
AUTHORISED
AUTHORISED
MTB Rigid Comp
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
* Only a specially designed basket.
** For models with a seatpost strap.
Advice
For the safety of our customers, we recommend installation is only carried out by one of our approved technicians.
21
GUARANTEE CHARTER
The guarantee covers:
The guarantee does not cover:
•Any equipment or manufacturing defect observed by a
B'Twin workshop team, the replacement of defective parts
with compliant parts for the same use, and labour.
•All " b’Twin " branded products are guaranteed for 2 years
unless otherwise indicated and in normal and recommended
conditions of use.
•This B’Twin guarantee presents no obstacle to the
application of the legal guarantee against latent defects.
•Damage engaging the liability of a third party or resulting
from an intentional fault.
•Damage resulting from maintenance and use not in
accordance with the manufacturer's recommendations or
negligence.
•Wear parts (bulbs, cables and cable casings, brake pads,
chainrings, chains, rims, cod wheels, tyres, inner tubes, inside
guards, etc) and labour hours for replacing parts.
•Where the product is the subject of modifications performed
outside our workshops. Original parts replaced with
unauthorised parts.
•Damage resulting from fire, lightening, storm, vandalism or
unsecured transport.
Application of the guarantee:
•No impacts: the product must show no signs of damage due
to abnormal conditions of use.
•The product must be used in accordance with its
operating instructions and regularly serviced by our
workshops.
•Original parts have not been replaced by unauthorised
parts.
Duration of the guarantee:
•5 years for the frame.
•2 years for parts and labour.
SAFETY: 10 BIKE CONTROL POINTS
9/TYRES
•Check tyre pressure
•Check the appearance
of the tyres (not
deformed, tyre
correctly inserted
in rim, fitted in the
correct way).
10/BRAKES
•Check left and right calipers
are centred
•Check contact between the
rim and brake pads
•Check brake pad tightness
•Check adjustment and
settings of brake levers
1/SADDLE
•Check it is centred, horizontal
and tightened
•Seatpost
•Check it is tight
2/STEERING
•Check the handlebars and stem are
centred and tightened
•Check the headset
•Check the suspension is working
3/HOUSINGS
•Check the cable
housings are correctly
positioned in the cable
stops
8/ACCESSORIES
•Check that the
following are
present and
functioning:
- the bell
- reflector
- lighting and other*
7/DERAILERS
•Check the
adjustment of the
derailer stops
•Check that the
gear shifters are
functioning and
performing well
5/CRANKS
•Tighten the pedals
•Check that the crank
screws are tightened
•Check the position of
your automatic pedal
cleats*
6/CHAIN
•Check chain
flexibility
•Check the
detachable
chain link
4/WHEELS
•Check that the wheels are
centred and tightened
•Check that the wheels are not
buckled
* depending on model (rear shock absorber, mudguard, luggage rack...)
22
23
City and country
The following chart enables the optimal position of the rider to be determined, S(cm) being the rider's height.
Elops
S (cm)
Hs (cm)
155-159
Original
h (cm)
S (cm)
Hs (cm)
h (cm)
55.5
160-164
62
160-164
58
165-169
64.5
165-169
60
170-174
66.5
170-174
62.5
175-179
69
175-179
64.5
180-185
72
180-184
67
-
-
-
185-190
69.5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
+7
+12
24
+6.5
Route
Sports-Cycling
Sports-Cycle tourism
S(cm)
Hs (cm)
h (cm)
S(cm)
Hs (cm)
h (cm)
150-154
59
-2.5
150-154
59.5
-4.5
155-159
61.5
-3
155-159
62
-5
160-164
64
-3.5
160-164
64.5
-5.5
165-169
66.5
-4
165-169
67
-6
170-174
69
-4.5
170-174
69.5
-7
175-179
71.5
-5
175-179
72
-7.5
180-184
74
-5.5
180-184
74.5
-8
185-189
76.5
-6
185-189
77
-8.5
190-194
79
-6.5
190-194
79.5
-9
195-200
82
-7.5
195-200
82
-10
Competition-Performance
S(cm)
Hs (cm)
h (cm)
150-154
60
-7
155-159
62.5
-7.5
160-164
65
-8
165-169
67.5
-9
170-174
70
-9.5
175-179
72,5
-10
180-184
75
-11
185-189
77.5
-11.5
190-194
80
-12
195-200
82.5
-13
25
MTB
Recreational off-road
S(cm)
Hs (cm)
150-154
58
Off-road sports
h (cm)
S(cm)
Hs (cm)
h (cm)
150-154
59
-2.5
155-159
61.5
-3
160-164
64
-3.5
+1.5
155-159
60.5
160-164
63
+1
165-169
65.5
165-169
66.5
170-174
68
170-174
69
175-179
70.5
175-179
71.5
-4.5
180-184
73
180-184
74
-5
185-189
76.5
-5.5
-4
+0.5
0
185-189
75.5
190-194
78
-0.5
190-194
79
195-200
80.5
-1
195-200
81.5
-6
Competition-Performance
S(cm)
Hs (cm)
h (cm)
150-154
59,5
-6.5
155-159
62
-7.5
160-164
64.5
-8
165-169
67
-8.5
170-174
69.5
-9
175-179
72
180-184
75
185-189
77.5
-10
190-194
80
-10.5
195-200
82.5
-11.5
-9.5
26
20"
14"
S(cm)
Hs (cm)
90-94
95-99
32
100-105
others
h (cm)
48
S(cm)
49
120-124
50
125-129
16"
105-109
110-114
115-120
h (cm)
51
42
130-135
51.5
52
FS
48.5
37.5
Hs (cm)
49
120-124
49
125-129
130-135
27
58
45
59
60
24"
Boys series
S(cm)
Hs (cm)
h (cm)
135-139
61
140-144
54
145-155
62
Girls series
135-139
140-144
57
54
145-155
57.5
58
28
Importado para Brasil por IGUASPORT Ltda.
CNPJ : 02.314.041/0001-88
TURKSPORT Spor Urünleri Sanayi ve Ticaret Ltd.Şti
Mega Center C 36 Blok D: 374 Bayrampaşa
34235 Istanbul - Turkey
Импортер: ООО «Октоблу», 141031, Россия, Московская область,
Мытищинский район, МКАД 84-й км.,
ТПЗ «Алтуфьево», владение 3, строение 3
16” : GB 14746 - ≥ 20” : GB 3565
Réf. Pack : 1213.138
OXYLANE
4, boulevard de Mons - BP 299
59665 Villeneuve d’Ascq cedex
France