Yamakawa DVD-MP12i Instruction manual

SC ALAMSERVICE 96 SRL
MS-MBN2
www.alarmservice.ro
SC ALAMSERVICE 96 SRL
Contents:
Contents ...................................................................................................................................... 2
Safety instructions ...................................................................................................................... 3
Service / communication ............................................................................................................ 4
Shipment..................................................................................................................................... 4
Product description ..................................................................................................................... 5
Installation of cable kit MS-MBN2 with MULTI10 ............................................................... 5-7
Function and controls (Mercedes) .............................................................................................. 8
Installation of cable kit MS-MBN2 with MULTI15 ............................................................. 9-10
Function and controls (Range Rover) ................................................................................. 10-11
Installation of cable kit MS-MBN2 with MULTI20 ........................................................... 12-13
Function and controls (Porsche) .......................................................................................... 13-14
Device-specific codes and button assignment for NTG1 / NTG2 / PCM 2.1 ..................... 14-16
www.alarmservice.ro
SC ALAMSERVICE 96 SRL
Safety instructions:
1. Read through mounting guidelines:
Please read through all safety instructions and handling directions intently before installation
and start up of the device.
2. Keep mounting guidelines:
Keep the instruction manual and safety instructions for potential further reference.
3. Caution advises:
Please follow all caution advises contained in the mounting guidelines.
4. Water and humidity:
The device should not be operated near water or near a humidity source.
5. Warmness / heat:
The device should not be set up in direct proximity of heat sources (e. g. power amplifier).
6. Electric power supply:
The device should only be operated at a +12 volt vehicle electrical system.
7. Connection / electric power supply:
Use the device only at a +12 volt vehicle electrical system. Make sure to have a proper
ground.
8. Intrusion of objects or liquids:
Please make sure that no objects or liquids can intrude the interior of the device! (Danger of
short circuit!)
9. Repairs:
You should call on qualified personnel, if:
a plug or a connector have been damaged
cables are damaged
objects have fallen into the device or liquids have intruded it
the product has been exposed to humidity
the device doesn't function normally or if
significant changes in the operating performance can be observed
the product/casing has been damaged.
10. Operation:
Start no operation that is likely to distract you for a prolonged time from road traffic or traffic
related events – RISK OF ACCIDENT!!!
11. Warranty:
The warranty will cease in case that:
you open the device or the casing
you carry out repairs single handed
you use the device improperly
the device shows damages caused by external forces or mischievous destructions.
We assume no liability for damages to the vehicle or to people.
www.alarmservice.ro
SC ALAMSERVICE 96 SRL
Product description:
Article:
Function:
MS-MBN2
Cable kit for Multimedia Interface “MULTI10” / “MULTI15” /
“MULTI20” for use in conjunction with the
following systems:
Mercedes NTG1:
E-Class W211, CLS W219 (with video-fakra plug)
Mercedes NTG2:
A-Class W169, B-Class W245
C-Class W203 up to 4/2004
R-Class W251, M-Class W164
CLK W209 , GLX164
Range Rover:
Vogue , Sports , Discovery from model 2006
Porsche:
Cayenne PCM 2.1
Connection assignment of the cable kit:
Cable color/Connector:
● Red:
● Black:
3,5mm Jack Socket:
Fakra-Green:
Connector/Assignment:
+12V DC
GND
Control
Video-Line
Installation of cable kit with MULTI10:
Instructions for Mercedes W169, W245, W203, W209, W251, W164
with NTG2 System:
Warning: Do not install interface while ignition is turned on.
1. Remove all covers around the COMAND.
2. Remove the 4 screws attaching the COMAND to the center
console and remove it carefully.
www.alarmservice.ro
SC ALAMSERVICE 96 SRL
3. Disconnect the original Quadlock-connector from the device.
Connect the green Fakra-plug (Video-Line) to the COMAND.
Remove one of the two optical cables from the original
Quadlock-connector and connect it to the enclosed
LWL-connector.
Connect the second optical cable to the original
Quadlock-connector. Pay attention to the directional arrows
as shown in the picture on the right.
4. Connect the black wire of the cable kit to ground and the
red wire to 12V plus.
Connect the corresponding control cable (e.g. „STK-AL25“
for DVD Alpine devices) to the jack socket. Additionally, the
available Y-adapter „CABLE-415“ (sold separately) may be
used to enable the connection of the IR-remote receiver of a
video source parallel to the interface itself.
Furthermore, a second Y-adapter may be used for parallel
control of an additional video source if the adapter is
connected between the jack socket of the cable kit and the
corresponding control cable.
5. Connect the three Cinch sockets of the interface to the video
source using a Video / Audio Cinch cable (not included).
Reconnect the original Quadlock- connector to the COMAND.
6. Re-attach system to center console.
www.alarmservice.ro
SC ALAMSERVICE 96 SRL
Instructions for Mercedes W211, W219 with NTG1 system:
Warning: Do not install interface while ignition is turned on.
1. Remove all covers below the COMAND.
2. Loosen the two screws attaching the COMAND to the center
console and carefully extract it.
3. Disconnect the original Quadlock-connector from the device.
Connect the green Fakra-plug (Video-Line) to the COMAND.
Remove one of the two optical cables from the original
Quadlock-connector and connect it to the enclosed
LWL-connector.
Connect the second optical cable to the original
Quadlock-connector. Pay attention to the directional arrows
as shown in the picture on the right.
4. Connect the black wire of the cable kit to ground and the
red wire to 12V plus.
Connect the corresponding control cable (e.g. „STK-AL25“
for DVD Alpine devices) to the jack socket. Additionally, the
available Y-adapter „CABLE-415“ (sold separately) may be
used to enable the connection of the IR-remote receiver of a
video source parallel to the interface itself.
Furthermore, a second Y-adapter may be used for parallel
control of an additional video source, provided that the adapter
is connected between the jack socket of the cable kit and the
corresponding control cable.
5. Connect the three Cinch sockets of the interface to the video
source using a Video / Audio Cinch cable (not included).
Reconnect the original Quadlock- connector to the COMAND.
6. Re-attach system to center console.
www.alarmservice.ro
SC ALAMSERVICE 96 SRL
Function and controls (Mercedes):
Pushing the “Video“ button activates the
AV-input of the COMAND.
Prolonged pushing (2 Sec.) the “1“ and then
the “*” button activates the device channel
input.
Input now device-specific control selection
requires entering a two-digit number (e.g.
“01“ denotes controls for the DVD USB
Player) followed by pushing the “OK“ button.
Pushing the “5” button for a prolonged time
switches between device controls.
For a detailed button assignment see page 16/17.
Device RC Codes:
Model
DVD USB, MP410, MP412, AD212U, DVP-1000M, DVP900HD
DVBT2007, Dietz 1491/V
AMPIRE DVB-T100
DVB2008, TRT400
DVDC CKO DVC10
DVD-Changer CKO- DVC 6M , Yamakawa DVD-Changer
DVBT NL, SENERGY, C-KO DVBT-1080, Axion DVBT 500
DVD ADJQ-DVDRD, PYLE PLTD24, Veba,
Carmedien CM06
DVD 1/2 DIN (NO NAME)
DVD Alpine RUE - 4201
DVD Alpine RUE - 4158;TUE-T150DV
DVBT Eastern SE863-T
iPod® Vlink
DVBT ZENEC ZE-DVBT25
V-HUB VPA-B222R Alpine Radio
V-HUB VPA-B222R Alpine DVD
DVD Necvox DVA-3206
Analog-TV Alpine TUE-T112P
Analog-TV TRT-003
BOA-DVD 85700 /AIV, C-KO 412
DVD Visteon VXM2200
DVBT Quantum QTM10
DVD Elite ELT-900XU Novosonic
DVDC CkO MPC6
DVD-TIXXON (No Name)
Model
RC Code:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
HD-Player 3,5“ MVIX MV-5000U
DVD Axion VDV-402
DVD Bullit CDVD12
DVD ZENEC ZE-080
DVBT Ampire DVBT200
DVBT&DVD USB Digitaldynamic Multiplayer
iPod Alpine KCE-425I
A-TV TVT-765
Emperor Mini DVBT
DVBT Carmedien DVB423
DVBT M-DTV-201-0
DVDC Pioneer XDV-P6 (Reserviert)
RC Code:
DVD Phonocar VM 015 (USB/SD)
Hirschmann DVBT / Visteon DVBT
HD Microlab - Pocket X Div 25 (2,5 Zoll HD P. Tixxon)
DVB-T D80
DAS / Dietz 1492 DVB-T
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
DVBT Ampire DVBT50
NavNGo
TRI1100 DVB-T (USBHDMI)
DVD500UX
HD DVB-T MPEG-4 VCAN (HDMI, USB)
DVD Phonocar VM 015 (USB/SD) – Klon
ZEMEX DVBT D90 (DVB600)
Alpine KCE-635 (USB Player)
DVB 288 CS (MPG4 DVB-T)
DVBT Carmedien DVB423 (2 Generation)
43
44
45
46
47
48
49
50
51
52
www.alarmservice.ro
SC ALAMSERVICE 96 SRL
Installation of cable kit with MULTI15:
Instructions for Ranger Rover Vogue, Sports, Dicovery 3:
Warning: Do not install interface while ignition is turned on.
Discovery 3
Vogue
1. Extract the touch screen monitor from the center console.
2. Connect the green Fakra connector (Video-Line) of the
cable kit MS-MBN2 directly to the monitor.
3. Remove one of the two optical cables from the original
connector (please pay attention to the directional arrows)
and insert it into the supplied LWL-connector.
Connect the second optical cable to the original
connector.
4. Connect the black wire of the cable kit to ground and the
red wire 12V permanent plus.
Connect the corresponding control cable (e.g.“ STK-AL25“
for DVD Alpine devices) to the jack socket.
The optionally available Y-adapter ”CABLE-415“ (sold
separately) may be used to enable the connection of the
IR-remote receiver of a video source parallel to the
interface itself. Furthermore, a second Y-adapter may be
used for parallel control of an additional video source,
provided that the adapter is connected between the jack
socket of the cable kit and the corresponding control cable.
www.alarmservice.ro
Sports
SC ALAMSERVICE 96 SRL
5. Use a Video / Audio Cinch cable (sold separately) to
connect the video source to the three Cinch sockets of the
interface.
6. Re-attach the system to the center console.
Function and controls (Range Rover):
Pushing the “TV“ field in the main menu displays
the TV system layer.
Once a TV system was selected, exit the current layer
by pushing the“ “ symbol
Pushing the “Auto“ field switches to the control
selection layer.
It allows parallel access of up to two devices.
Return to the main menu by pushing the“
symbol.
“
The numeric array together with two arrow fields
displayed in the main menu are used to remotely
control the video source(s).
For detailed controls refer to the chart below.
www.alarmservice.ro
SC ALAMSERVICE 96 SRL
Button Assignment
●─● RANGE ROVER VOGUE, SPORTS, DISCOVERY 3 ●─●
Model
DVD / DVDC
PLAYER
DVB-T TUNER
1
2
3
4
5
6
7
8
SOURCE
UP
MENU/PBC
LEFT
ENTER/OK
RIGHT
STOP
DOWN
AV / DVB
UP
MENU
LEFT
OK
RIGHT
FAV
DOWN
ANALOG TUNER
MODE
VOL +
POWER
CH -
ADJUST
CH +
FM
VOL -
COMBI DVD/DVB-T
SOURCE
UP
MENU/PBC
LEFT
ENTER
RIGHT
STOP
DOWN
9
PLAY/
PAUSE
EXIT
DISPLAY
PLAY/
PAUSE
|<
>|
TRACK -
TRACK +
CH -
CH +
CH -
CH +
TRACK -
TRACK +
<<
ANGLE
/ DISC
EPG
>>
SCAN
AUTO
SCAN
-
Please note, that the |< and >| buttons on the multi function steering wheel are only supported
in the Range Rover Vogue
Note: Depending on the type of the video source to be connected, the interface needs to be
pre-configured by its manufacurer to enable video control functions.
www.alarmservice.ro
-
-
SC ALAMSERVICE 96 SRL
Installation of cable kit with MULTI20:
Instructions for Porsche Cayenne PCM 2.1 system:
Warning: Do not install interface while ignition is turned on.
1. Carefully remove the decorational cover surrounding the
navigation system using appropriate tools.
Loosen the 4 TORX-screws as marked in the picture on
the right and extract the device from the center console.
2. Disconnect all plugs from the device.
Connect the green Fakra-plug (Video-Line) to the PCM 2.1
system. Remove one of the two optical cables from the
original connector and connect it to the enclosed LWLconnector. Connect the second optical cable to the original
connector. Pay attention to the directional arrows as shown
in the picture on the right.
4. Connect the black wire of the cable kit to ground and the
red wire to 12V plus.
Connect the corresponding control cable (e.g. „STK-AL25“
for DVD Alpine devices) to the jack socket. Additionally, the
available Y-adapter „CABLE-415“ (sold separately) may be
used to enable the connection of the IR-remote receiver of a
video source parallel to the interface itself.
Furthermore, a second Y-adapter may be used for parallel
control of an additional video source, provided that the adapter
is connected between the jack socket of the cable kit and the
corresponding control cable.
.
www.alarmservice.ro
SC ALAMSERVICE 96 SRL
5. Connect the three Cinch sockets of the interface to the video
source using a Video / Audio Cinch cable (not included).
Reconnect the original Quadlock- connector to the PCM 2.1
system.
6. Re-attach system to center console.
Function and controls (Porsche):
To be able to use the controls, station buttons 0-9 of
the PCM 2.1 system need to be assigned the
corresponding control channels.
Pushing the “AV“ button activates TV input.
Pushing the right knob accesses the TV menu and
enables the selection of the memory layers (AS, A
or B): Layer “A“ needs to be selected.
Station buttons 0-9 are assigned to channel
numbers at the „chanel input“ level:
1. Use the right knob to select the channel number (Ch 1)
2. Push the right knob briefly
3. Push the „back arrow“ button to retun to previous menu
4. Push station button „1“ for 2 secound (confirmend
by a sound)
- Repeat this procedure until all stations buttons
have been assigned to channels numbers
Assign station buttons as indicated:
Station Btn.:
Channel Nr.:
1
01
2
02
3
03
4
04
5
05
6
06
7
07
8
08
9
09
0
10
www.alarmservice.ro
SC ALAMSERVICE 96 SRL
Device Assignment:
Access the menu level “INFO“ → “VIDEOTEXT“ in
order to select controls for a specific device.
Enter the three digit device RC Code using the keypad
(e.g. for DVP-900HD ”101”) in order to store RC code.
Device RC Codes:
Model
RC Code:
DVD USB, MP410, MP412, AD212U, DVP-1000M, DVP-900HD
101
DVBT2007, Dietz 1491/V
AMPIRE DVB-T100
DVB2008, TRT400
102
103
104
DVDC CKO DVC10
DVD-Changer CKO- DVC 6M , Yamakawa DVD-Changer
DVBT NL, SENERGY, C-KO DVBT-1080, Axion DVBT 500
DVD ADJQ-DVDRD, PYLE PLTD24, Veba, Carmedien CM06
DVD 1/2 DIN (NO NAME)
DVD Alpine RUE - 4201
DVD Alpine RUE - 4158;TUE-T150DV
DVBT Eastern SE863-T
iPod® Vlink
DVBT ZENEC ZE-DVBT25, TRT500
V-HUB VPA-B222R Alpine Radio
V-HUB VPA-B222R Alpine DVD
DVD Necvox DVA-3206
Analog-TV Alpine TUE-T112P
Analog-TV TRT-003
BOA-DVD 85700 /AIV, C-KO 412
DVD Visteon VXM2200
DVBT Quantum QTM10
DVD Elite ELT-900XU Novosonic
DVDC CkO MPC6
DVD-TIXXON (No Name)
HD-Player 3,5“ MVIX MV-5000U
DVD Axion VDV-402
DVD Bullit CDVD12
DVD ZENEC ZE-080
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
Model
DVBT Ampire DVBT200
DVBT&DVD USB Digitaldynamic Multiplayer
iPod Alpine KCE-425I
A-TV TVT-765
DVBT Emperor DTR-1203
DVBT Carmedien DVB423
DVBT M-DTV-201-0
DVD 600 (1/2 DIN USB/SD)
RC Code:
DVD Phonocar VM 015 (USB/SD)
Hirschmann DVBT / Visteon DVBT
HD Microlab - Pocket X Div 25 (2,5 Zoll HD P. Tixxon)
DVB-T D80
DAS / Dietz 1492 DVB-T
DVBT Ampire DVBT50
NavNGo
TRI1100 DVB-T (USBHDMI)
DVD500UX
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
HD DVB-T MPEG-4 VCAN (HDMI, USB)
DVD Phonocar VM 015 (USB/SD) – Klon
ZEMEX DVBT D90 (DVB600)
Alpine KCE-635 (USB Player)
DVB 288 CS (MPG4 DVB-T)
DVBT Carmedien DVB423 (2 Generation)
147
148
149
150
151
152
www.alarmservice.ro
SC ALAMSERVICE 96 SRL
Button Assignments for PCM2.1:
●─● PCM2.1 ●─●
Modell
1
2
3
4
5
6
7
8
9
0
|<<
>>|
DVD PLAYER
PLAY
↑
STOP
←
ENTER
→
PBC
↓
SETUP
AV
TRACK-
TRACK+
DVD CHANGER
PLAY
↑
STOP
←
ENTER
→
DISC
↓
SETUP
AV
TRACK-
TRACK+
DVB-T TUNER
SCAN
PLAY/
PAUSE
SCAN
↑
EPG
←
OK
→
EXIT
↓
MENU
AV
CH-
CH+
↑
POWER
←
ENTER
→
SHUFFLE
↓
LIGHT
EJECT
TRACK-
TRACK+
VOL+
FM
CH-
MODE
CH+
MUTE
VOL-
MODE
DISPLAY
CH-
CH+
I-POD® CONTROL
ANALOG TUNER
Button Assignments for NTG1 / NTG2:
●─● COMAND NTG 1/2 short press ●─●
Modell
1
2
3
4
5
6
7
8
9
0
*
|<<
>>|
DVD PLAYER
PLAY
↑
STOP
←
ENTER
→
PBC
↓
SETUP
AV
RC CODE
TRACK-
TRACK+
DVD CHANGER
PLAY
↑
STOP
←
ENTER
→
DISC
↓
SETUP
AV
RC CODE
TRACK-
TRACK+
DVB-T TUNER
SCAN
PLAY/
PAUSE
SCAN
↑
EPG
←
OK
→
EXIT
↓
MENU
AV
RC CODE
CH-
CH+
↑
POWER
←
ENTER
→
SHUFFLE
↓
LIGHT
EJECT
RC CODE
TRACK-
TRACK+
VOL+
FM
CH-
MODE
CH+
MUTE
VOL-
MODE
DISPLAY
RC CODE
CH-
CH+
I-POD® CONTROL
ANALOG TUNER
●─● COMAND NTG 1/2 long press ●─●
Modell
1
2
3
4
5
6
7
8
9
0
DVD PLAYER
Set RC1
Set RC2
-----
DISPLAY
SWITCH AV1/AV2
-----
-----
POWER
Set RC1
Set RC2
-----
DISPLAY
SWITCH AV1/AV2
AUDIO
AUDIO
SUB
DVD CHANGER
SUB
-----
-----
POWER
DVB-T TUNER
Set RC1
Set RC2
-----
SIGNAL
SWITCH AV1/AV2
AUDIO
LANG
-----
-----
POWER
-----
-----
-----
POWER
MUTE
-----
-----
POWER
I-POD® CONTROL
Set RC1
Set RC2
-----
-----
SWITCH AV1/AV2
MUTE
ANALOG TUNER
Set RC1
Set RC2
-----
DISPLAY
SWITCH AV1/AV2
FM
We wish you a lot of fun with your new device and thank you for deciding in favor of our product.
www.alarmservice.ro