Midmark 6230 (Non-Powered Phlebotomy Cart) Installation manual

Add to my manuals
2 Pages

advertisement

Midmark 6230 (Non-Powered Phlebotomy Cart) Installation manual | Manualzz

MASTER CODE COMMANDS

CHANGE THE MASTER CODE

#Master Code

65

New Master Code

New Master Code

••

Example: #55443322

65

12345678

12345678

••

Result

Master Code has been changed to 12345678

SET OR CHANGE THE USER CODE

#Master Code

60

Example: #55443322

User Code

60

9999

••

Result

New User Code 9999 now operative

DELETE USER CODE

#Master Code

64

Example: #55443322

Result

User Code deleted

••

64

••

SET OR CHANGE THE SUB-MASTER CODE

#Master Code

69

Example: #55443322

Sub-Master Code

69

87654321

Sub-Master Code

87654321

••

••

Result

Sub-Master Code 87654321 now operative

DELETE SUB-MASTER CODE

#Master Code

63

Example: #55443322

63

••

63

Result

Sub-Master Code deleted

63

••

SUB-MASTER CODE COMMANDS

CHANGE THE SUB-MASTER CODE

#Sub-Master Code

68

New Sub-Master Code

New Sub-Master Code

Example: #87654321

68

10101010

10101010

••

Result Sub-Master Code has been changed to 10101010

SET OR CHANGE THE USER CODE

#Sub-Master Code

Example: #87654321

62

62

User Code

6666

••

••

Result New User Code 6666 now operative

DELETE USER CODE

#Sub-Master Code

Example: #87654321

67

••

67

••

Result User Code deleted

USER CODE COMMANDS

CHANGE THE USER CODE

#User Code

New User Code

Example: #0099

6688

6688

Result User Code now 6688

New User Code

••

••

SPECIAL MASTER CODE COMMANDS

SET REPEATED USE MODE A)

#Master Code

08

••

Example: #55443322

08

••

Result The lock will revert back to default function A) repeated use.

Factory set User Code 0099 will now work repeatedly until reprogrammed.

SET SINGLE USE MODE B) (LOCKER MODE)

#Master Code

09

••

Example: #55443322 09

Step 1 – Enter 4 digit code

••

Result The lock will now remain open until the next single use code is entered into the lock as follows: •

Confirm 4 digit code

Close the locker which will now be locked.

Step 2 – Enter the same 4 digit code

••

Note:

•• the lock will now open and

When locked in this mode

LED will flash every 5 seconds to indicate the locker is locked.

SET TECHNICIAN CODE

#Master Code

11

Example: #55443322

Technician Code

11

555555

Technician Code

555555

••

••

Result The lock is automatically set into function B) single use Locker Mode

AND allows the programmed Technician Code to open the lock WITHOUT the entered single use code being erased.

Note: If lock is opened with a Master Code the User Code will be erased.

CODELOCKS LTD UK

Tel: +44 (0) 1635 239645

Fax: +44 (0) 1635 239644 [email protected]

Helpline, service & spares

FREEPHONE 0800 393 405

CODELOCKS INC US

Tel: +1 714 979 2900

Fax: +1 714 979 2902 [email protected]

Help: 1.877.CODELOCK

www.codelocks.com

PROGRAMMING

OPERATING

INSTRUCTIONS

FOR RIGHT HAND

HORIZONTAL

KITLOCK1000

WWW.KITLOCK.COM

CODES - THE BASICS

• The KitLock has four

code levels available:

i) Master Code

ii) Sub-Master Code

iii) User Code

iv) Technician Code

• The KitLock is supplied

with two factory set codes:

Master Code: 55 44 33 22

User Code: 00 99

• When fitted immediately

change the Master Code

and User Code.

• All Master Codes and Sub-

Master Codes are 8 digits long.

• All User Codes are 4 digits long.

• The lock ‘open’ time is set

at 4 seconds.

B) SINGLE USE (Locker Mode)

The user enters a Single Use Code twice; the second time to confirm the correct code.

This locks the lock. The same code is entered once only to open the lock before being erased.

This function is used for short term, multi occupancy applications, e.g. a locker in a leisure centre.

FUNCTIONS

Before programming, select the most appropriate function for the application: A) or B) - See special Master Code set up

commands.

A) REPEATED USE

Important Note: This is the default function and is already pre-programmed in new locks.

This is the most common function and is used where the same code will be

repeatedly used.

OPERATING INSTRUCTIONS

Note: The KitLock has a 10 button keypad and a # button. The # button is hidden beneath the handle when in the locked position.

The lock has the following code levels:

Master Code can:

Open the lock

Change the Master Code

Set / Change / Delete the Sub-Master and User Code

Select between repeated use and single use codes

Activate/deactivate technician mode

Sub-Master Code can:

Open the lock

Change the Sub-Master

Set / Change / Delete / the User Code

User Code can:

Open the lock

Change the User Code

Technician Code can:

Open the lock

A code cannot be programmed into more than one level

Lost Code Procedure

Note: The procedure requires the door to be open

• Remove the rear-fixing bolt and swing the lock over the edge of the door to reveal the battery compartment.

• Remove one battery.

• Press and hold the 5 button, replace the battery, the blue LED will flash twice, release the 5 button. Within three seconds press the

5 button three times. The blue LED will flash twice and the lock will have reverted to the factory master code 55 44 33 22 and all other stored settings will be erased.

Penalty time

• Entering three incorrect codes will cause the lock into shutdown for 10 seconds.

Battery Power

The KitLock should provide well in excess of 15,000 openings, of 4 seconds each, from 2 x AAA 1.5v cells.

Low Battery

When the battery power is low the Red LED will flash 3 times before the Blue LED flashes to signal acceptance of the code. Batteries should be changed as soon as this happens.

The lock will operate for 100 times with low battery.

Code rejected

Code accepted

Battery failure override

The KitLock has been designed so an external PP3 battery can be placed against the contact points surrounding the Blue and

Red LED’s so the lock can be opened to replace the batteries should they fail.

The procedure is as follows:

• Place the contact points of the PP3 battery against the contact points surrounding the Blue and Red LED’s.

• The positive + PP3 terminal against the

Red LED contact point and the negative –

PP3 terminal against the Blue LED.

• Enter the Master Code.

• The motor will withdraw the locking pin allowing the lock to be opened.

• Fit new batteries by removing the upper fixing bolt and swinging the lock down over the edge of the door. Refit the lock.

PROGRAMMING

To program – the lock must be in the open position with the # button visible. Every program command must commence by pressing the

# button, followed by either the Master Code, Sub-Master Code or

User Code.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement