DC C640 Digital Camera
User Manual
Welcome
Downloaded From camera-usermanual.com BenQ Manuals
Copyright
Copyright 2007 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of this company.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose.
Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time
in the contents hereof without obligation of this company to notify any person of such revision or changes.
Taking care of your camera
• Do not use your camera in the following environmental range: temperature below 0°C or above 40°C.
• Do not use or store your camera in the environments listed below:
– Direct sunlight
– High and dusty places
– Next to an air conditioner, electric heater or other heat sources
– In a closed car that is in direct sunlight
– Unstable locations
• If your camera becomes wet, wipe it with a dry cloth as soon as possible.
• Salt or seawater may cause severe camera damage.
• Do not use solvents, such as alcohol, to clean your camera.
• If the lens is dirty, use a lens brush or soft cloth to clean the lens. Do not touch the lens with your fingers.
• To prevent electric shock, do not attempt to disassemble or repair your camera by yourself.
• Water may cause a fire or electric shock. Therefore, store your camera in a dry place.
• Do not use your camera outdoors when it is raining or snowing.
• Do not use your camera in or near water.
• If a foreign substance or water gets in your camera, please turn the power off immediately and remove the
batteries. Remove the foreign substance or water, and send it to the maintenance center.
• Transfer the data to the computer as soon as possible to avoid losing your images and / or video clips.
Disposal of Waste Electrical and Electronic Equipment by users in private households in the European Union.
This symbol on the product or on the packaging indicates that this can not be disposed of as
household waste. You must dispose of your waste equipment by handing it over to the
applicable take-back scheme for the recycling of electrical and electronic equipment. For more
information about recycling of this equipment, please contact your city office, the shop where
you purchased the equipment or your household waste disposal service. The recycling of
materials will help to conserve natural resources and ensure that it is recycled in a manner that
protects human health and environment.
CE Regulatory Notice
Hereby, BenQ Corp. declares under our responsibility that the product is in conformity with the requirements
set out in the Council Directive on the Approximation of the Laws of the Member States relating,
Electromagnetic Compatibility Directives (89/336/EEC, 92/31/EEC) and Low Voltage Directive (73/23/EEC).
A "Declaration of Conformity" in accordance with the above Directives has been made and is available from
BenQ Corp. upon request.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
Downloaded From camera-usermanual.com BenQ Manuals
turning the equipment o. and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Downloaded From camera-usermanual.com BenQ Manuals
<Memo>
Downloaded From camera-usermanual.com BenQ Manuals
1.1 Checking the package contents ............................................. 1
1.2 Camera components .......................................................... 1
1.2.1 Front view ........................................................... 1
1.2.2 Rear view ............................................................. 2
1.2.3 LED indicators ..................................................... 2
2. Preparing Your Camera for Use ............................................... 3
2.1 Installing the batteries......................................................... 3
2.2 Inserting and removing an SD memory card........................... 3
3. Using the Camera .................................................................... 4
3.1 Navigator ......................................................................... 4
3.2 LCD monitor information (REC mode) ................................ 4
3.3 Getting started................................................................... 5
3.3.1 Turning the power on / off ..................................... 5
3.3.2 Choosing the screen language ................................. 5
3.3.3 Setting the date and time ........................................ 5
3.3.4 Snapshot mode ..................................................... 5
3.3.4.1 Getting started with capturing images ................ 5
3.3.5 Using the flash ...................................................... 6
3.3.6 Using the self-timer and burst ................................. 6
3.3.7 Using the zoom function ........................................ 7
3.4 Menu options.................................................................... 7
3.4.1 Changing the mode ............................................... 7
3.4.1.1 Switching between REC mode and PLAY mode ... 7
3.4.1.2 Selecting the Scene mode ................................. 8
3.4.2 Using the menus ................................................... 9
3.4.2.1 REC menu list (still image) .............................. 9
3.4.2.2 REC menu list (movie) .................................... 9
3.4.3 Setup menu ....................................................... 10
3.4.3.1 Setup menu list ............................................ 10
3.5 Recording movie clips ...................................................... 12
3.6 Recording audio clips ....................................................... 12
3.7 Other recording functions ................................................. 12
3.7.1 Setting the quality ............................................... 12
Table of Contents
Downloaded From camera-usermanual.com BenQ Manuals
i
English
Table of Contents
1. Touring Your Camera.............................................................. 1
English
3.7.2 Setting the metering ............................................ 13
3.7.3 Setting the white balance ...................................... 13
3.7.4 Setting the ISO ................................................... 13
3.7.5 Setting the Exposure ............................................ 14
3.7.6 Setting the AEB .................................................. 14
3.7.7 Setting the highlight ............................................ 14
3.7.8 Setting the sharpness ........................................... 14
3.7.9 Setting the photo effect ........................................ 14
3.7.10 Setting the date stamp .......................................... 15
3.7.11 Setting Stabilizer ................................................. 15
3.7.12 Setting Face tracking............................................ 15
3.7.13 Setting Photo Frame ............................................ 15
3.7.14 Setting Av/Tv/M ................................................. 15
3.8 Playback ......................................................................... 15
3.8.1 Playing back images............................................. 15
3.8.2 Playing back movie clips ...................................... 16
3.8.3 Magnifying & trimming still images ....................... 16
3.8.4 Viewing in thumbnail .......................................... 16
3.8.5 Playing a slide show ............................................. 16
3.8.6 Deleting a single file or all files .............................. 17
3.8.7 Deleting multiple files .......................................... 17
3.8.8 Setting the DPOF for printing ............................... 18
3.8.9 Other playback functions ..................................... 18
4. PC Dependent Features ......................................................... 19
4.1 Bundled software ............................................................. 19
4.2 Transferring files to your computer..................................... 19
4.2.1 Step 1: Connect the digital camera to your computer 20
4.2.2 Step 2: Download images or video clips .................. 20
5. Troubleshooting .................................................................... 21
6. Specifications ........................................................................ 23
7. Service Information ............................................................... 24
ii
Table of Contents
Downloaded From camera-usermanual.com BenQ Manuals
Touring Your Camera
1.1
Checking the package contents
Carefully unpack your kit box and ensure that you have the following items.
1.
2.
3.
4.
5.
6.
7.
8.
•
•
•
1.2
User Manual
Digital camera
USB cable
AA batteries
Hand strap
Software CD-ROM
Pouch
AV cable
Available accessories may vary depending on sales region.
If any of the items are missing or appear to be damaged, contact your dealer. Save the
packaging in case you need to ship your camera for service.
All electronic accessories (such as USB, AV cable, adapter, charger, and battery) are
designed to work with this BenQ Digital Camera only. Do not use them with other
Digital Camera to avoid possible damage
Camera components
1.2.1 Front view
1.
2.
3.
4.
5.
6.
7.
8.
Shutter button
Built-in flash
Power button
Speaker
PC (USB) / AV Out terminal
Lens
Microphone
Self-timer LED
Touring Your Camera
Downloaded From camera-usermanual.com BenQ Manuals
1
English
1
•
English
If your BenQ camera's lens remains extended after an involuntary shutdown, simply
replace the batteries with new ones and restart your camera.
Never forces the lens inwards since this action will damage the camera and void the
BenQ Warranty.
1.2.2 Rear view
1.
2.
LCD monitor
W
Zoom-out or thumbnail
3. T
Zoom-in
4. Strap eyelet
5. REC or PLAY mode
6. Menu
7. Status LED
8. Navigator -- four-way
control and OK
9. Scene mode
10. Av/Tv/M Aperture priority,
Shutter priority, or Manual)
in the REC mode, or Delete
image/video in the PLAY
mode
8
1.2.3 LED indicators
Indicator
Status LED
State
Description
No light
The digital camera is powering off.
Solid green
The digital camera is ready to capture images.
Blinking
green
The digital camera is powering on, cannot focus, record
video clips, or is in the power-saving mode.
Blinking red The camera/flash is charging, or the USB
communication/transfer is in progress.
Self-timer LED
Blinking red The self-timer function is activated.
• It is normal for the camera to become warm during operation, because camera casing
can conduct heat.
• The LCD display on this camera is manufactured with sophisticated technology, and
more than 99.99% of the pixels on the LCD display meet standard specifications. Yet, it is
possible that less than 0.01% of the pixels on the LCD display may have some light spots
or show unusual colors. This is normal and does not indicate display malfunction, nor
will this affect the pictures you take with the camera.
2
Touring Your Camera
Downloaded From camera-usermanual.com BenQ Manuals
Preparing Your Camera for Use
2.1
Installing the batteries
You can use two AA batteries to power up the camera.
Make sure that the power of the digital camera is off
before inserting or removing the batteries.
To insert the batteries:
1. Make sure the camera is turned off.
2. Open the battery cover.
3. Insert the batteries in the correct orientation as
shown in the illustration.
4. Close the battery cover.
To remove the batteries:
1. Make sure the camera is turned off.
2. Hold the camera with the battery cover facing upward, and then open the battery cover.
3. Remove the batteries.
2.2
Inserting and removing an SD memory card
The camera is equipped with internal memory, allowing
you to record video clips and capture images. You can also
expand the memory capacity by using an optional SD
(Secure Digital) memory card to store more files.
1. Always make sure the camera is turned off before
inserting or removing a memory card.
2. Insert an SD memory card in the correct orientation as
shown in the illustration.
3. Close the battery / SD memory card cover.
To remove the SD memory card, make sure the camera is turned off. Press lightly on the
edge of the memory card and it will eject.
• Be sure to format the SD memory card with this
camera before the initial use.
• To prevent valuable data from being accidentally
erased from an SD memory card, you can slide the
write-protect tab (on the side of the SD memory card)
to “LOCK”.
To save, edit, or erase data on an SD memory card, you must unlock the card.
•
• SD memory card in the following sizes are supported: 64 MB, 128 MB, 256 MB, 512 MB, 1
GB, 2GB and 4GB SDHC. The camera is compatible with SD memory cards manufactured
by Panasonic, Toshiba, and Sandisk. Please contact your local dealer for purchase
information.
Preparing Your Camera for Use
Downloaded From camera-usermanual.com BenQ Manuals
3
English
2
English
3
Using the Camera
3.1
Navigator
You can use the Navigator with four-way control and one OK button to access numerous
controls of your camera.
1.
2.
3.
4.
5.
3.2
Up
or Play (video playback only)
Focus mode or left
Down
Flash mode or right
OK
LCD monitor information (REC mode)
P
6M
EV
-1.0
1. Scene mode
2. Flash
3. Macro
4. Self-timer/Burst
5. Resolution
6. Quality
7. Shots remaining
4
9999
ISO
A 100
8. ISO
9. White balance
10. Metering
11. EV compensation
12. Focus Area
13. Hisogram
14. Battery
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
Getting started
3.3.1 Turning the power on / off
•
Press the [
] button until the digital camera turns on. Or, you can press the [
button when the camera is off to turn on the camera.
•
To turn the power off, press the [
]
] button again.
3.3.2 Choosing the screen language
1. Press MENU, and then press [
]/[
] to move to the Setup menu.
2. Press [ ] or [ ] to move to Language, and then press [
language you want.
3. Press OK.
] or OK to select the
3.3.3 Setting the date and time
1. Press MENU, and then press [
]/[
] to move to the Setup menu.
2. Press [
] or [
] to move to Date & Time, and then press [
3. Press [
] or [
] to select Year, Month, Day, Time, and Format fields.
•
To increase a value, press [
] or OK.
].
• To decrease a value, press [ ].
• The time is displayed in 24 hour format.
4. Press OK.
3.3.4 Snapshot mode
3.3.4.1
Getting started with capturing images
1 Press down halfway
1. Press the [
] button for more than one second to
turn on the camera.
2. Compose your image in the LCD monitor under
Snapshot Mode.
3. Press the shutter button down halfway (1), and then
press it down fully (2).
• Pressing the shutter button down halfway
automatically focuses and adjusts the exposure.
• The focus area frame turns green when the
2 Press down fully
camera is focused and the exposure is
determined.
• When the focus or exposure is not suitable, the frame of the focus area turns red.
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
5
English
3.3
English
• To review the last captured image, press the
button. Press the
button to return
to Snapshot mode.
• The LCD monitor darkens in strong sunlight or bright light. This is not a malfunction.
• To prevent your images from being blurred while pressing the shutter button, always hold
the camera steady. This is especially important when you are shooting under low lighting
conditions, under which your camera may reduce the shutter speed to ensure your
images are properly exposed.
3.3.5 Using the flash
The flash is not only for taking pictures when there is insufficient light, but also when the
subject is in shade or in backlight conditions. Pressing the flash button cycles your camera
through the various flash modes. The flash will not activate when continuous shooting or
movie recording.
1. Turn the power on, and set the camera to the REC mode.
2. Pressing the flash button changes the flash mode. Each time the flash button is pressed,
the flash icon changes.
3. Press the shutter button to take a picture.
Icon
Flash mode
Description
Auto flash
Flash fires automatically when shooting conditions require extra
lighting.
Red-eye
reduction
Flash strobes to let the subject eyes adjust to the flash, then fires
again to take the actual image. Your camera will detect the
subject brightness and use the flash only when required.
Force on
Flash fires every time you take a photo, regardless of lighting
conditions.
Slow sync
Flash fires with a slow shutter speed.
Force off
The flash never fires even in dark situation.
3.3.6 Using the self-timer and burst
Use the self-timer to set a delay from the time the shutter button is pressed to the time the
image is shot. Use the burst to record continuous still images shooting.
1. Turn the power on, and set the camera to the REC mode.
2. Press the MENU, and then press the [
3. Press [ ] / [
the submenu.
]/[
] to select the REC menu.
] to select Driver mode and then press [
] or the OK button to launch
4. Press [ ] / [ ] to select an option and press the OK button to apply the setting. Press
the MENU button to close the menu and the shutter button to take pictures.
6
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
-
Flash mode
Description
Off
Record a single image.
2 sec.
The shutter release will be delayed for 2 seconds.
10 sec.
The shutter release will be delayed for 10 seconds.
Double
Record two images in a shot after pressing the shutter release
button 10 and 12 seconds.
Burst
Keep pressing the shutter button fully to take a continuous
shooting. Release the shutter button to stop shooting.
English
Icon
2
10
3.3.7 Using the zoom function
Your camera has a combination of optical and digital zoom functions that allows you to
zoom in on far away subjects or zoom out for a wide angle shot.
The optical zoom is achieved by mechanically adjusting the lens of the camera. The digital
zoom enlarges or shrinks the image using a software process.
1. Make the zoom setting, and point the camera at the subject.
2. Press the zoom button (W/T) to compose the image.
[W]: zoom out for a wide-angle shot.
[T]: zoom in for a telephoto shot.
• When the zoom button is pressed, the zoom bar appears on the LCD monitor.
• When the optical zoom factor is at maximum, zooming stops temporarily. Press the
[T] again, the camera switches to the digital zoom automatically and zooming
continues.
• You can use optical zoom in movie recording.
3. Press the shutter button to take a picture.
3.4
Menu options
3.4.1 Changing the mode
You can record images and voices in the REC mode. And using the PLAY mode to replay,
delete, or edit images on the LCD monitor.
3.4.1.1
•
•
Switching between REC mode and PLAY mode
In REC mode, press the PLAY button to switch to the PLAY mode.
In PLAY mode, press the PLAY or the MODE button to switch to the REC mode.
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
7
3.4.1.2
Selecting the Scene mode
English
1. Set the camera to the REC mode.
2. Press the MODE button to show the scene mode palette.
3. Use the four-way control to select a desired mode and press OK to confirm the setting.
Icon
Mode
Description
Program
The camera makes settings suitable for the shooting conditions.
Movie
For recording movie clips.
Voice REC
For recording audio.
Sunset
Enhance the red hue for recording sunset images.
Backlight
Shooting the image of backlight object by changing metering.
Shake-Free
Reduce blur caused by camera vibration.
Landscape
Used for the wide scenic views.
High ISO
Portrait
Use a higher ISO value to make people stand out with the
background out-of-focus even in a dark environment.
Snow
Used for the beach or snow scenes.
Fireworks
Slow shutter speed to take fireworks exploding.
Night Scene
Shooting the subject while keeping the background night
scenery.
Kids
Take a still image to capture moving kids.
Food
Higher saturation makes food more appetizing.
Building
Enhance the edges of the subject.
Text
Enhance the black & white contrast.
• The higher the ISO value, the grainer you may see in the image.
8
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
3.4.2 Using the menus
2. Press the MENU and then press the [
3. Press [ ] / [
the submenu.
]/[
English
When a menu is displayed, the four-way control and the OK button are used to make the
desired settings.
1. Turn the power on, and set the camera to the REC mode.
] to select the REC menu.
] or the OK button to launch
] to select a menu item and then press [
4. Press [ ] / [ ] to select an option and press the OK button to apply the setting.
5. Press the MENU button to close the menu.
3.4.2.1
REC menu list (still image)
Menu item
Available settings
Resolution
/
Quality
/
/
/
/
/
/
/
/
/
/
/
Metering
White Balance
/
ISO
/
/
Exposure
/
/
/
/
/
-2.0 EV ~ +2.0 EV
Drive Mode
AEB
Off /
2 /
10 /
/
Off / On
Highlight
Off /
Sharpness
/
/
/
/
Effect
Normal / B&W / Sepia / Negative / Red / Green / Blue
Date Stamp
Off / Date / Date & Time
Stabilizer
Off / On
Face Tracking
Off / On
Photo Frame
Off / 1-10 frames
Digital Zoom
Off / On
3.4.2.2
Menu item
Movie Size
REC menu list (movie)
Available settings
/
/
/
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
9
Menu item
Available settings
English
Metering
/
White Balance
/
/
/
/
/
/
/
3.4.3 Setup menu
1. Turn the power on, and set the camera to the REC or PLAY mode.
2. Press the MENU, and then press the [
3. Press [ ] / [
the submenu.
]/[
] to select the Setup menu.
] to select a menu item and then press [
] or the OK button to launch
4. Press [ ] / [ ] to select an option and press the OK button to apply the setting.
5. Press the MENU button to close the menu.
3.4.3.1
Setup menu list
Menu item
Sounds
Auto Review
Power Save
Functions
[Shutter]
Sets the shutter sound on and off.
[Start-up]
Sets a type of the start-up sound.
[Beep]
Sets the operation sound on and off.
[Volume]
Adjusts the volume of the shutter sound, startup sound, beep and playback sound.
[Off]
The captured image will not automatically
display after shooting.
[3 sec.]
The captured image will display for 3 seconds
after shooting.
[5 sec.]
The captured image will display for 5 seconds
after shooting.
[1 min.]
For power consumption, the camera is turned
off automatically for a period of time.
[3 min.]
[5 min.]
10
Date & Time
Sets the date & time.
Language
Select a language for display menus and other information.
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
Functions
File No.
Use this function if the camera experiences a "Folder cannot be
created" error or if you want to restart numbering, for example,
after erasing all files.
TV Out
[Series]
Store the latest used file number no matter
deleting files or inserting a new memory card.
[Reset]
Reset file numbering each time the memory
card is changed. Resetting the file number is
useful for avoiding the file name duplication
when images are downloaded to a computer.
English
Menu item
You can review images on a television with a supplied AV cable.
TV Out should be set to either NTSC or PAL depending on your
region.
[NTSC]
America, Japan, Taiwan and others
[PAL]
Europe, Oceania and others
TV Out should be set to either NTSC or PAL depending on
your region. For details about which system should be used, check
with your local authorities.
USB
[Computer]
[Printer]
Sets the USB mode to connect the camera with
a printer or computer.
Start-up Image
Sets a recorded image as the start-up image.
Format
To erase all data stored in the memory card if you are using a card,
or all data stored in the internal memory if there is no card
inserted.
A “Busy...please wait” message displays and the memory card is
starting format.
A “Completed” message displays when finish formatting.
All data will be deleted including protected files. Be sure to
download important files to your computer before formatting.
Battery Type
To ensure the camera displays battery level correctly, set the type
to match the batteries used.
Reset All
[Alkaline]
When use alkaline batteries.
[NiMH]
When use NiMH batteries.
Resets the entire menu and button operation settings to initial
default.
The following settings do not change after Reset All:
Date & Time setting
Language setting
TV out setting
Battery Type
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
11
3.5
Recording movie clips
English
1. Turn the power on, and set the camera to the Movie mode.
2. Compose the subject on the monitor.
• Aim the focus area to the subject that you want to take.
• The LCD monitor displays the available recording time
3. Start recording.
• Press the shutter button to start recording.
• Using the zoom button to adjust the image size.
• The White Balance is set and locked to the settings of the first frame.
• Sound cannot be recorded while pressing the zoom button.
• You can use optical zoom in movie recording.
4. Finish recording.
• Press the shutter again to end recording.
• The camera will stop recording automatically when the memory capacity has been
reached.
3.6
Recording audio clips
1. Turn the power on, and set the camera to the Voice REC mode.
2. Press the shutter button to start recording.
• The voices are recorded from the microphone of the camera. Be careful to avoid
touching the microphone while recording.
3. Press the shutter button again to end recording.
• The camera will stop recording automatically when the memory capacity has been
reached.
3.7
Other recording functions
3.7.1 Setting the quality
Compression
12
Purpose
Super Fine
Shoot higher quality images.
Fine
Shoot normal quality images.
Normal
Shoot for more images.
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
There are 3 different light metering options available on your camera.
Icon
Mode
Description
Center
Light is measured from the entire shooting screen, but gives more
importance to the values near the center.
Multi
Selects an exposure based on readings from multiple points in the
subject area
Spot
Selects an exposure based on a single reading taken from the center
of your picture.
3.7.3 Setting the white balance
Adjust the white balance to match different light sources such as sunlight, incandescent
(tungsten) lighting or, fluorescent lighting.
Icon
Mode
Description
Auto
Automatically corrects white balance. Ideal for general photography.
Daylight
Adjusts for bright sun conditions, or natural light conditions.
Cloudy
Adjusts for cloudy days or twilight conditions.
Tungsten
Adjusts for normal indoor lighting conditions. Corrects the orange
hue of household light bulbs. Ideal for indoor photos under
tungsten or halogen lighting without a flash.
Fluor_H
Fluor_L
Adjusts for fluorescent lighting. Corrects the green hue of
fluorescent lighting. Ideal for indoor photos under fluorescent
lighting without a flash.
SH1
(Custom)
For more accurate adjustment or when the light source cannot be
specified. When this option is highlighted, press the shutter button
to enter the [Custom WB] mode. Then, point the camera at
something white (for example, white paper) as the reference white
color and press the shutter button again. Next, press OK to confirm
the custom setting.
3.7.4 Setting the ISO
With the initial settings, the ISO sensitivity is automatically set according to the brightness of
the subject.
• A higher ISO value increases the image noise. To take clean images, use an ISO value as
low as possible.
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
13
English
3.7.2 Setting the metering
3.7.5 Setting the Exposure
English
Set the exposure value manually to compensate for unusual lighting conditions such as
indirect indoor lighting, dark backgrounds, and strong backlighting.
3.7.6 Setting the AEB
Sets the auto exposure bracketing (AEB) to shoot 3 continuous images, each with a different
exposure setting: correctly exposed, underexposed, and overexposed.
3.7.7 Setting the highlight
Make the subject stand out from its surroundings. The subject will be in focus in three
different ranges:
/
/
3.7.8 Setting the sharpness
You can select whether you want the image to have sharp or soft outlines.
Icon
Mode
Description
Hard
The edges of the image are emphasized. The edges will become sharp, but
noise may occur in the recording image.
Normal The edges of the image are sharp. This is suitable for printing.
Soft
The edges of the image are softened. This is suitable for editing images on
PC.
3.7.9 Setting the photo effect
You can add special effects to your images in REC or PLAY mode.
14
Icon
Description
Normal
No effect is added to the image.
B&W
Convert image to black & white.
Sepia
Recorded image will be stored in a sepia tone.
Negative
Opposite what they were in the original image.
Red
The image becomes reddish.
Green
The image becomes greenish.
Blue
The image becomes bluish.
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
The Date Stamp function can be used to add a date to your pictures as you take them.
3.7.11 Setting Stabilizer
With more sensibility and faster shutter speed to bright up the pictures, effectively prevent
blur image caused by hand shack or target movement, one can take good pictures with little
effort.
3.7.12 Setting Face tracking
After initializing face tracking function, the lens will lock the main character in the picture
and follow the movements. Also use auto digital zoom technology to retract and extract
zoom lens that allows you to become the focus of lens.
3.7.13 Setting Photo Frame
You can add 10 kinds of frames to still images, making them more interesting.
3.7.14 Setting Av/Tv/M
Pressing the Tv/Av/M button
toggles among Aperture priority, Shutter priority, and
Manual when determining the exposure value.
• Aperture priority: You can choose an aperture value, while the shutter speed is
automatically determined by the lighting condition of the subject. Aperture priority is
often used when shooting static subjects or emphasizing the depth of field. In general,
use a smaller aperture if a greater depth of field is needed.
• Shutter priority: You can choose a shutter speed, while the aperture value is
automatically determined by the lighting condition of the subject. Shutter priority is
often used when shooting moving subjects. In general, use a shorter shutter speed to
catch a fast-moving object.
• Manual: You can set both the shutter speed and the aperture value.
3.8
Playback
3.8.1 Playing back images
1. Turn the power on, and set the camera to the PLAY mode.
• The latest recorded image appears on the LCD monitor.
• If there are no images stored, a message [No image] appears.
2. Press the four-way control.
•
[
] displays the previous image.
•
[
] displays the next image.
• Holding down [
] or [
] scrolls images in a high speed.
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
15
English
3.7.10 Setting the date stamp
3.8.2 Playing back movie clips
English
1. Turn the power on, and set the camera to the PLAY mode.
2. Press [ ] or [ ] to select a movie clip that you want to playback.
3. Start playing back.
•
Press [
•
Press [
] to start playing the movie clip.
] to stop the movie clip, or press [
press [
] again to resume.
] to pause it. When the movie paused,
• During movie playing back, press [ ] to fast forward or press [ ] to rewind it.
• Press the shutter to capture the still image from the movie clip while it had paused.
3.8.3 Magnifying & trimming still images
1. Turn the power on, and set the camera to the PLAY mode.
2. Select an image.
• Press [ ] or [ ] to select the image that you want to magnify or trimming.
• Only still images can be magnified and trimmed.
3. Magnify the image.
• Press [T] to magnify the image, and the central portion of the image is displayed. You
can use the arrow button to view different parts of the magnified image.
• Press the MENU button to return to the normal size.
4. Trim the image.
• Press the OK button to set the image trimming.
5. Save the image.
• Press the OK button again to trim the selected image and save it as a new one.
3.8.4 Viewing in thumbnail
1. Turn the power on, and set the camera to the
PLAY mode.
2. Press the zoom button [W], a thumbnail screen is
displayed.
3. Use the four-way control to select the desired
image, and press [T] or the OK button to show the
selected image in full screen.
3.8.5 Playing a slide show
1. Turn the power on, and set the camera to the
PLAY mode.
2. Enter the slide show.
•
16
Press the MENU button and use the [
or the OK button.
]/[
] to select Slide Show and press [
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
]
Protect...
Start
Delete...
Interval:
Slideshow...
Music:
DPOF...
Transition:
Copy to Card...
OK
Set
English
3. Change the slide show settings.
• Use the four-way control to set the slideshow
interval, music, transiton and repeat.
• You can set the interval between 1~10
seconds.
4. Playing the slide show.
• Press the OK button to start the slideshow.
• During the slide show, press the OK button to
pause the slideshow and press the OK button
again to resume.
10s
1
MENU
Back
3.8.6 Deleting a single file or all files
1. Turn the power on, and set the camera to the PLAY mode.
2. Press [ ] or [ ] to select the image you want to delete.
3. Open the menu.
•
Press the MENU button, then use the [
•
Press the [
4. Press [
] or [
]/[
]/[
] to select PLAY mode.
] to select Delete and press the [
] to select [Single], and press the [
]or OK button.
] or OK button.
• To delete all images, select [All] and press the [ ] or OK button.
5. Select [Yes] and press OK button to delete the image.
• To quickly delete the current display image:
1. Select the image you want to delete.
2. Press the Delete button to show a confirmation.
3. Press the OK button to delete the current display image.
• Protected images cannot be deleted with this function.
3.8.7 Deleting multiple files
1. Turn the power on, and set the camera to the
thumbnail screen.
2. Open the menu.
•
Press the MENU button, then press [
[ ] to select to select Delete
the OK button.
] or
and press
3. Press [ ] or [ ] to select [Select], and then
press the OK button.
• The frame of the selected image turns green.
4. Select multiple images.
• Use the four-way control to select the image.
•
Press the OK button toggles the
De lete
Se lec t
Al l
Ba ck
Protect
Delete
on and off. Repeat this step until all images that
you want to delete are displayed with an icon
.
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
17
English
5. Delete images.
• Press the MENU button, then select [Yes] and press the OK button. All selected images
will be deleted.
• To cancel delete, press the MENU button in this step.
3.8.8 Setting the DPOF for printing
The Digital Print Order Format (DPOF) setting allows you to select images on the memory
card for printing and specify the number of print copies in advance using the camera. This is
extremely convenient for sending the images to a photo developing service or for printing on
a direct print function compatible printer.
1. Turn the power on, and set the camera to the PLAY mode.
2. Open the menu.
• Press the MENU button, then use the [ ] / [ ] to select PLAY mode.
•
Press the [
]/ [
] or OK button.
] ] to select DPOF and press the [
3. Press [ ] or [ ] to select [Single], then press the OK button.
• To set the DPOF setting for all images in a time, select [All] in this step.
• To reset all DPOF settings to initial default, select [Reset] in this step.
4. Press [ ] or [ ] to select the image you want to print out, then press the OK button.
5. Set the number of copies.
•
•
•
Press [ ] or [ ] to specify the number of copies.
The number of copies can be set from 0 to 30.
To cancel this image DPOF setting, set the number of copies to 0.
6. Print the date stamp
•
•
out.
Press [ ] and then press [ ] or [ ] to set or cancel the date stamp of current
image.
Repeat step 4~6 to other images for printing.
7. Press [ ] and then press the OK button to apply the setting or press the MENU button to
cancel.
8. After you finished all image settings, select[Back]and press the OK button to apply it.
3.8.9 Other playback functions
You can also protect (lock) images from being deleted, edit images, copy files, or enter setup
for more options. To do so, press the MENU button in the PLAY mode, and select a function.
Photo Frame...
Protect...
Delete...
Slideshow...
DPOF...
Copy to Card...
OK
18
Enter
MENU
Back
OK
Enter
MENU
Using the Camera
Downloaded From camera-usermanual.com BenQ Manuals
Back
PC Dependent Features
4.1
English
4
Bundled software
The camera is supplied with the following software. To install the software, refer to the
information supplied with respective CDs.
ArcSoft
PhotoImpression 5
Combine l'édition de photos avec des outils d'amélioration créative
et de partage d'outils qui maximise votre expérience média
numérique.
ArcSoft
VideoImpression 2
Crée des présentations multimédia en combinant des photos et des
clips vidéo avec de l'audio, du texte et des transitions entre les
scènes.
4.2
Transferring files to your computer
After using USB cable to establish a USB connection between the camera and your computer,
you can use your computer to share captured images or recorded video clips with your family
or friends via e-mail or post them on the Web. Note that before you begin, you need to check
your system according to the table as shown below.
System Requirements (Windows)
CPU
Pentium III 600 MHz processor or higher
Operating System Windows Me / 2000 / XP / Vista
RAM
64 MB
Hard Disk Space
128 MB hard disk space
Required Devices
A CD-ROM drive
An available USB port
Display
Color Monitor (800 x 600, 24-bit or higher recommended)
PC Dependent Features
Downloaded From camera-usermanual.com BenQ Manuals
19
4.2.1 Step 1: Connect the digital camera to your computer
English
1. Connect the supplied USB cable to the computer USB port and turn on the camera.
2. The LCD screen turns off when the connection to the computer has been successfully
completed.
4.2.2 Step 2: Download images or video clips
When the digital camera is turned on and connected to your computer, it is considered to be
a disk drive, just like a floppy disk or CD. You can download (transfer) images by copying
them from the “Removable Disk” to your computer hard drive.
Windows
Open the “Removable Disk” and double-click on the DCIM folder to open it to find more
folders. Your images are inside these folder(s). Select the desired still images or video clips,
and then choose “Copy” from the “Edit” menu. Open the destination location (folder) and
choose “Paste” from the “Edit” menu. You may also drag and drop image files from the digital
camera to a desired location.
• Memory card users may prefer to use a memory card reader (highly recommended).
• Video playback application is not included with the package. Make sure that video playback application has been installed in your computer.
20
PC Dependent Features
Downloaded From camera-usermanual.com BenQ Manuals
Troubleshooting
Refer to the symptoms and solutions listed below before shipping your camera for service. If
the problem persists, contact your local reseller or service center.
Symptom
Cause
The camera cannot be There is no battery or the battery is
powered up.
not inserted correctly.
The battery has no power.
The battery power is
draining quickly.
Solution
Insert the battery correctly.
Recharge your batteries or replace
with new batteries.
The external temperature is
extremely low.
—
Many shots are being captured in
dark places, requiring a flash.
—
Fully charge the battery and
The battery was not fully charged.
The battery has not been used for an discharge it for at least one complete
extended period of time after being cycle before use.
charged.
The battery or camera The camera or flash was used
is warm.
continuously over a long period of
time.
The flash does not
fire.
The flash does not
recharge.
The camera flash is turned off.
—
Set the flash to Auto Flash.
The light source is sufficient.
—
The flash is not available in some
modes.
—
Even though the flash The distance to the subject is greater Get closer to the subject and shoot.
fired, the image is
than the flash’s effective range.
dark.
The image is too
bright or too dark.
The exposure is excessive or
inadequate.
Reset exposure compensation.
I cannot format a
memory card.
The memory card is writeprotected.
Remove the write protection.
End of the memory card life.
Insert a new memory card.
Troubleshooting
Downloaded From camera-usermanual.com BenQ Manuals
21
English
5
English
Symptom
Cause
Solution
I cannot download
images.
The free space on the hard disk of
your computer is insufficient.
Ensure that the hard disk has enough
space for running Windows and that
the drive for loading image files has
free space equal to or greater than the
memory card in the camera.
There is no power being supplied to Recharge your batteries or replace
the camera.
with new batteries if necessary.
The camera does not
shoot even when
pressing the shutter
button.
The battery is running low.
Recharge your batteries or replace
with new batteries.
The camera is not in Shooting
Mode.
Switch to Shooting Mode.
The shutter button was not pressed
all the way down.
Press the shutter button all the way
down.
The internal memory or memory
card does not have any free space.
Load a new card or delete unwanted
files.
The flash is recharging.
Wait until the flash mode icon,
indicated on the screen, stops
flashing.
The camera does not recognize the
memory card.
Format the memory card before the
initial use or before using with
another camera.
Colors of the images
taken are not shown
properly.
White Balance was not set properly
when these images were taken.
Select a suitable White Balance
setting before taking each picture.
After connecting the
camera to a
computer, an error
message “Device not
ready” or “Camera
not ready” appears.
The computer runs on Windows 98
or earlier.
—
When connecting the The memory card inside the camera Format the memory card to the
camera to a
may not be formatted.
FAT16 format using a card reader in
computer, the
Windows.
computer freezes.
A memory error
occurs.
22
The memory card may not be
formatted correctly.
Re-format the memory card to the
FAT16 format using a card reader in
Windows.
Troubleshooting
Downloaded From camera-usermanual.com BenQ Manuals
Specifications
Image Sensor
1/2.5-inch CCD
Effective Pixels: 6.0 Mega pixels
LCD Display
2.5" LTPS TFT LCD
Lens
Focal Length: f = 6.2 -18.6 mm (35 mm film equivalent: 37.5-112.5 mm)
F No.:F2.8/F5.2
Focusing
TTL Auto Focus
Shutter
Mechanical shutter: Up to 1/2000 sec.
Range: Macro: 15 cm, Normal: 40 cm ~ infinity
Flash
Modes: Auto/Forced flash/Red-eye reduction/Flash off/Slow Sync
Range: 0.5 ~ 2.0m
Self-timer
2 sec. /10 sec.
Exposure
Compensation: ±2 EV (1/3 EV/step)
ISO
Auto/50/100/200/400/800
White Balance
Auto/Sunny/Cloudy/Tungsten/Fluorescent H/Fluorescent L/MWB
File Format
Still Image: JPEG format (EXIF2.2), DCF Image Size: 2816 x
2112(6M),2816 x 1584(16:9),2784 x 1856(3:2),2304 x 1728(4M), 1600 x
1200(2M),640 x 480(VGA) pixels
Movie Clips: AVI (Motion JPEG) format with Continuous recording. Movie
Size: 848 x 480,640 x 480, 320 x 240,160 x 120 pixels (30fps)
Storage
Built-in memory: 6MB/SD memory card compatible.
Image Play
Single image/AVI play/Thumbnails/Slide show
Interface
Digital output: USB 2.0 high-speed compatible Audio/Video output
(NTSC/PAL)
Power Source
2 x AA batteries( Alkaline or NiMH)
Dimensions
(W x H x D)
91.5x61.5x26 mm
Weight
Approx. 140 (w/o battery, SD memory card)
6* Design and specifications are subject to change without notice.
Specifications
Downloaded From camera-usermanual.com BenQ Manuals
23
English
6
English
7
Service Information
Technical Support
For free driver updates, product information and news releases, visit the following web site:
http://www.BenQ.com
24
Service Information
Downloaded From camera-usermanual.com BenQ Manuals