White Rodgers P200 Operating instructions

Blue Universal Thermostat with
Automatic Heat/Cool Changeover Option
Single Stage, Multi-Stage or Heat Pump
Installation and Operating Instructions for Model:
Save these instructions for future use!
Model
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS
CAREFULLY BEFORE INSTALLING OR OPERATING
THIS CONTROL COULD CAUSE PERSONAL INJURY
AND/OR PROPERTY DAMAGE.
Programming Choices
1F85CA-0471
5/1/1 Day
5/2 Day
Non-Programmable
1F85-0471
5/1/1 Day
5/2 Day
Non-Programmable
1F83-0471
Non-Programmable
APPLICATIONS
THERMOSTAT APPLICATION GUIDE
1F85CA-0471 Thermostat
Description
Heat Pump (No Aux. or Emergency Heat)
Yes
Heat Pump (with Aux. or Emergency Heat)
Yes
Systems with up to 2 Stages Heat, 2 Stages Cool
Yes
Heat Only Systems (with optional fan switch)
Yes
Millivolt Heat Only Systems – Floor or Wall Furnaces
Yes
Cool Only Systems
Yes
Gas or Oil Heat
Yes
Electric Furnace
Yes
Hydronic (Hot Water) Zone Heat – 2 Wires
Yes
Hydronic (Hot Water) Zone Heat – 3 Wires
Yes
Compressor with Comfort Alert II Module (1F85CA only)
Yes
SPECIFICATIONS
Electrical Rating:
Battery Power ....................................................
Input-Hardwire ...................................................
Terminal Load ...........................................................
Setpoint Range .........................................................
Differential (Single Stage) .........................................
Differential (Heat Pump) ...........................................
Operating Ambient ....................................................
Operating Humidity ...................................................
Shipping Temperature Range ...................................
Dimensions Thermostat ............................................
! CAUTION
To prevent electrical shock and/or equipment damage,
disconnect electric power to system at main fuse or
circuit breaker box until installation is complete.
Index
Installation
Wiring Connections
Wiring Diagrams
Thermostat Quick Reference
Installer Configuration Menu
Operating Your Thermostat
Programming
Troubleshooting
Page
2
2
3
4
5
7
7
9
mV to 30 VAC, NEC Class II, 50/60 Hz or DC
20 to 30 VAC
1.5 A per terminal, 2.5A maximum all terminals combined
45° to 90°F (7° to 32°C)
Heat 0.6°F; Cool 1.2°F (adjustable)
Heat 1.2°F; Cool 1.2°F (adjustable)
32° to +105°F (0° to +41°C)
90% non-condensing max.
-40° to +150°F (-20° to +65°C)
4.0”H x 5.11”W x 1.3”D
ATTENTION: MERCURY NOTICE
This product does not contain mercury. However, this product
may replace a product that contains mercury.
Mercury and products containing mercury must not be
discarded in household trash. Do not touch any spilled
mercury. Wearing non-absorbent gloves, clean up any spilled
mercury and place in a sealed container. For proper disposal
of a product containing mercury or a sealed container. Refer
to www.white-rodgers.com for location to send product
containing mercury.
PART NO. 37-6920B
www.white-rodgers.com
Replaces 37-6920A
1
0905
INSTALLATION
!
Figure 1 – Battery door shown open
WARNING
Thermostat installation and all components of the
control system shall conform to Class II circuits per
the NEC code.
“AA” Alkaline Batteries
Remove Old Thermostat
A standard heat/cool thermostat consists of three basic parts:
1. The cover, which may be either a snap-on or hinge type.
2. The base, which is removed by loosening all captive
screws.
3. The switching subbase, which is removed by unscrewing
the mounting screws that hold it on the wall or adapter
plate. Before removing wires from old thermostat,
label each wire with the terminal designation from
which it was attached. Disconnect the wires from the
old thermostat one at a time. Do not let wires fall back
into the wall.
Installing New Thermostat
1.
2.
3.
4.
5.
6.
7.
Pull the thermostat body off the thermostat base. Forcing
or prying on the thermostat will cause damage to the unit.
Place base over hole in wall and mark mounting hole
locations on wall using base as a template.
Move base out of the way. Drill mounting holes. If you
are using existing mounting holes and the holes drilled
are too large and do not allow you to tighten base snugly, use plastic screw anchors to secure the base.
Fasten base snugly to wall using mounting holes shown
in Figure 2 and two mounting screws. Leveling is for
appearance only and will not affect thermostat operation.
Connect wires to terminal block on base.
Push excess wire into wall and plug hole with a fire resistant material (such as fiberglass insulation) to prevent
drafts from affecting thermostat operation.
Carefully line the thermostat up with the base and snap
into place.
Thermostat can be powered by system AC power or Battery.
If
is displayed, the thermostat is battery powered. If
is not displayed, thermostat is system powered with optional
battery back-up. When battery power remaining is approximately half, the
will be displayed. When “Change
”
is displayed, install fresh “AA” alkaline batteries immediately.
For best results, replace all batteries with new premium brand
alkaline batteries such as Duracell® or Energizer®. We recommend replacing batteries every 2 years. If the home is going
to be unoccupied for an extended period (over 3 months) and
is displayed, the batteries should be replaced before
leaving. When less than two months of battery life remain, the
setpoint temperature will offset by 10 degrees (10 degrees
cooler in Heat mode / 10 degrees warmer in Cool mode). If
offset occurs, the normal setpoint can be manually reset with
or
. Another offset will occur within two days if batteries are not replaced.
Figure 2 – Thermostat base and rear view of thermostat
Mounting
Hole
Place Level
across
Mounting Tabs
(for appearance only)
Mounting
Hole
Place Level
across
Mounting Tabs
(for appearance only)
Batteries
2 “AA” alkaline batteries are included with the thermostat.
To install the batteries, pull the battery door as shown by the
arrow and lift open. Using the polarity indicated inside the battery door, insert the batteries. To close the battery door, swing
the door down while pulling in the direction of arrow. Once
fully down, snap the door back into position. To replace the
batteries, set system to OFF.
WIRING CONNECTIONS
Refer to equipment manufacturers’ instructions for specific
system wiring information. After wiring, see CONFIGURATION
section for proper thermostat configuration.
Refer to figure 3 through 6 for wiring diagram specifications.
TERMINAL DESIGNATION DESCRIPTIONS
Terminal
Designation
Description
L .............. Heat pump malfunction indicator for systems
with malfunction connection or Comfort Alert signal
O.............. Changeover valve for heat pump energized
constantly in cooling
B .............. Changeover valve for heat pump energized
constantly in heating
Y .............. Compressor Relay
Y2 ............. 2nd Stage Compressor
2
Terminal
Designation
Description
W/E ............Heat Relay/Emergency Heat Relay (Stage 1)
W2 .............2nd Stage Heat (3rd Stage Heat in HP 2)
G ..............Fan Relay
RH .............Power for Heating
RC .............Power for Cooling
C ..............Common wire from secondary side of cooling system
transformer or heat only system transformer
6...............3 Wire Zone Valve – Energized when no call for Heat
WIRING DIAGRAMS
Heat Pump Connections
If you do not have a heat pump system, refer to figures 4-6.
Refer to equipment manufacturers’ instructions for specific
system wiring information.
You can configure the thermostat for use with the following
heat pump systems.
Figure 3 – Heat Pump Systems
HEAT PUMP TYPE 1 (HP 1). Single stage compressor
system; gas or electric backup.
HEAT PUMP TYPE 2 (HP 2). Multi-stage compressor or two
compressor system with gas or electric backup.
After wiring, see INSTALLER CONFIGURATION section for
proper thermostat configuration.
Jumper
L
Y
O/B
Y2
Jumper
W2
W/E
NOTE: If your system does
not provide an E connection,
jumper W2 to W/E to use
the Auxiliary Heat in the
Emergency Mode.
C
RC
RH
G
System
Heat Pump 1
(HP1)
Heat Pump 2
(HP2)
Heat Mode
Blower/
2nd Stage.
Circulator
Emergency
Mode 2nd Fan Energized
Optional*
Heat and
Emergency
on Call for 24 Volt 24 Volt
Stage
24 Volt
Cool Mode
Mode
Heat or Cool. (Hot) (Hot)
(Com1st Stage
Heat Mode Set Elect/Gas Heat
1st
Stage
Cool
2nd
mon)
(Compressor)
3rd Stage.
Option for
Stage
Emergency Emergency
(ComMode 2nd
Mode
pressor)
Stage
O
Fault Indicator
or System
Malfunction
Switch
No
Output
Energized in
Cool Mode
B
Energized in
Heat, Off,
Emergency
Mode
Comfort Alert II Module
or Similar System
Malfunction Module
* Common connection
required for fault or
malfunction indication.
NEUTRAL
120VAC
24VAC
HOT
CLASS II
TRANSFORMER
Single Stage and Multi-Stage Connections
SINGLE STAGE (SS 1) gas, oil or electric.
Refer to equipment manufacturers’ instructions for specific
MULTI-STAGE (MS 2) gas, oil or electric.
system wiring information.
After wiring, see INSTALLER CONFIGURATION section for
This thermostat is designed to operate a single-transformer
proper thermostat configuration.
or two-transformer system.
You can configure the thermostat for use with the following
fossil fuel systems:
Figure 4 – Single Stage or Multi-Stage System (No Heat Pump) with Single Transformer
Jumper
L
Y
O/B
W/E
Y2
G
W2
RH
RC
C
System
Single
Stage 1
(SS1)
MultiStage 2
(MS2)
Blower/
O
No
Circulator
No Output
Energized Constantly
Fault
Output
Fan Energized
in Cool Mode
Indicator
Heat
on Call for
or
Cool Mode
Mode
Cool (and
System
1st Stage
B
Heat if
Cool 1st Stage Heat Mode
Malfunction
Energized Constantly
configured
Mode
2nd Stage
Switch
in Heat, Off,
for Electric
2nd
Emergency
Heat)
Stage
Mode
24 Volt 24 Volt
(Hot)
(Hot)
Cool
Heat
* Common connection
required for fault or
malfunction indication.
Optional*
24 Volt
(Common)
Comfort Alert II Module
or Similar System
Malfunction Module
NEUTRAL
120VAC
24VAC
HOT
CLASS II
TRANSFORMER
Figure 5 – Single Stage or Multi-Stage System (No Heat Pump) with Two Transformers
Remove Jumper Wire
between RH & RC
Jumper
L
Y2
Y
O/B
W/E
G
W2
RH
RC
C
System
Single
Stage 1
(SS1)
MultiStage 2
(MS2)
O
Fault
Indicator
(NOT
USED)
No
Output
Energized Constantly
in Cool Mode
B
Energized Constantly
in Heat, Off,
Emergency
Mode
Cool Mode
1st Stage
Cool
Mode
2nd
Stage
Blower/
Circulator
Fan Energized
Optional
24 Volt 24 Volt 24 Volt
on Call for
(Hot) (Hot) (ComCool (and
Heat Cool
Heat if
mon)
configured
Heat Mode
for Electric
2nd Stage
Heat)
No Output
Heat
Mode
1st Stage
NEUTRAL
120VAC
120VAC
24VAC
NEUTRAL
HOT
24VAC
COOLING
HOT
CLASS II
TRANSFORMER
HEATING
CLASS II
TRANSFORMER
Figure 6 – 3-Wire (SPDT) Heat Only Zone Valve Wiring
Jumper
6
Y
W
G
Opens
Valve
(4)
Blower/Circulator
Fan Energized
RH
RC
C
System
Single Stage
3-wire
Zone Valve
application
Closes
Valve
(6)
24 Volt
24 Volt
(Hot)
(Hot)
Heat
Cool
(5)
Constant
24 Volt
(Common)
NEUTRAL
120VAC
24VAC
HOT
CLASS II
TRANSFORMER
3
THERMOSTAT QUICK REFERENCE
Home Screen Description
Figure 7 – Home Screen Display
Room
Temperature
Displays the power level of
the 2 “AA” batteries:
indicates good power level
indicates batteries at about
half power. “Change
” indicates
batteries are low and should be
replaced with 2 new premium brand
“AA” Alkaline batteries.
(See page 2 for more details)
P
System
Indicator
1 “System On” indicates when heating or cooling stage
is energized. “System On +2” indicates when a second
stage is energized.
5 Displays System Mode (Heat, Emer, Auto, Cool, Off)
or “Time” in Menu Mode.
Menu
Fan
Indicator
Figure 8 – Programming & Configuration Items
Programming and Configuration Items
3 Displays “Change Filter” when the system has run for 3
the programmed filter time period as a reminder to
1
change or clean your filter.
4 Displays “Set” for setpoint when in Run Program mode. 9
Set
FAN
Auto
SYSTEM
Heat
2 The word “Hold” is displayed when the thermostat is in
the Hold mode. “Temp Hold” is displayed when
the thermostat is in a Temporary Hold mode.
Mo
Setting
Temperature
2
12
4
Mo Tu We Th Fr Sa Su
P Date Set
Temp Hold
Save
Month Call For Service
Year
Change
Hold
Filter
System On 2
Auto Sched
Cool Savings
Heat Pump
SYSTEM
Heat Emer Auto
Cool Off Time
FAN
On Auto
Run Sched
5
6
8
Run
Schedule
Menu
6 Displays Fan Mode (On, Auto) or “Run Sched” in
Menu Mode.
7 Displays “Run Schedule”, “Schedule”, or “Menu”.
TM
8 Displays “Save” when Cool Savings is working.
Displays “Heat Pump” when system is configured
9
as Heat Pump thermostat.
10 Displays “Hold” in programmable mode. When not in
Hold mode, displays (light bulb) in non-programmable
mode.
4
7
11 Initially displays “Auto Sched”. If Auto Schedule had
been used or disabled, then it displays “Cool Savings”
when in the Cool Mode if Cool Savings has been enabled in the menu.
12 “Call For Service” indicates a fault in the heating/
cooling system, it does not indicate a fault in the
thermostat.
10
11
INSTALLER/CONFIGURATION MENU
With thermostat in Heat, Cool or Auto, in normal operation, press the Menu button for at least 5 seconds. The display will show
item #1 in the table below. Press Menu button to advance to the next menu item. Press
or
to change an item option.
Shaded items not available on 1F83 model.
INSTALLER/CONFIGURATION MENU
DISPLAYED
MENU
Press
or
to
PRESS
REF. HP SS BUTTON (FACTORY DEFAULT) select from listed options
1
1
1
MENU
(MS 2)
HP 1, HP 2, SS 1
ELE
1, 2, 3, 4, 5, 6
2
2
2
MENU
3
3
3
MENU
4
4
4
MENU
(GAS) for SS or MS
(ELE) for HP
CS (0)
(Disabled)
E (On)
5
–
5
MENU
CR Heat (ME)
SL, FA
6
5
–
MENU
SL, FA
7
6
6
MENU
CR Heat Pump
(ME)
CR Cool (ME)
or
CR Emer (FA)
8
9
7
8
7
8
MENU
MENU
10
11
9
9
10 10
MENU
MENU
12
13
11 11
12 12
MENU
MENU
14
13 13
MENU
15
14 14
MENU
16
15 15
MENU
17
16 16
MENU
18
17
–
MENU
19
18
–
MENU
20
19 17
MENU
21
20 18
MENU
22
21 19
MENU
MENU
23
22 20
MENU
24
23 21
RUN
SCHED
CL (OFF)
Heat Auto
Cool Off
OFF
SL, FA
SL
COMMENTS
Selects Multi-Stage (MS 2 No Heat Pump),
Heat Pump 1 (HP 1, 1 compressor),
or Single Stage (SS 1), Heat Pump 2 (HP 2, 2
compressor or 2 speed compressor)
GAS setting: furnace controls the blower
ELE setting: thermostat controls the blower
Selects Cool Savings
Value 1 (low) to 6 (high), Value 0 Disables Feature
Selects Energy Management Recovery (EMR)
On or OFF. NA 1F83.
Adjustable Anticipation:
Selects heating cycle rate for MS or SS
Adjustable Anticipation (Heat Pump) (only
when heat pump selected in #1)
Adjustable Anticipation: Selects the cycle rate for
cooling (only when MS 2 or SS 1 is selected in
item 1.) or Selects the cycle rate for Emergency
mode and Auxiliary stage if Heat Pump is
selected in item 1.
Compressor Lockout Time
System Mode Configuration
with Automatic Changeover capability
CL On
Heat Cool Off,
Heat Off with Fan icon,
Heat Off without Fan icon
Cool Off, Auto Off
dL (On)
dL OFF
Selects Display Light On or OFF
0
1 HI, 2 HI, 3 HI, 4 HI,
Adjustable Ambient Temperature Display
(current temperature) 1 LO, 2 LO, 3 LO, 4 LO
Selects Fahrenheit/Celsius Temperature Display
°F
°C
L Heat
L 62 to L 89
Selects Limited HEAT Range
(90)
L Cool
L 46 to L 82
Selects Limited COOL Range
(45)
P3
P0, P2
Defaults for 5-1-1 programming (P3) but nonprogrammable (PO) or 5-2 programming (P2)
is available on most models. NA 1F83.
Heat AS (On)
OFF
Automatic Schedule for heat mode. NA 1F83.
NA to Cool only system.
Cool AS (On)
OFF
Automatic Schedule for cool mode. NA 1F83.
NA to Heat only system.
Heat FA (On)
OFF
Fast Heat option may be disabled by
selecting OFF. NA to SS config.
NA to Cool only system.
Cool FA (On)
OFF
Fast Cool option may be disabled by
selecting OFF. NA to SS config.
NA to Heat only system.
CA (OFF)
On
Selects active Comfort Alert On or OFF.
Requires CA II Module. (1F85CA only)
dS (On)
OFF
Selects Automatic daylight Savings Time option
On or OFF. NA 1F83.
Change Filter (OFF)
On
Selects Filter Change-out Indicator On or OFF.
Change Filter (200 h)
25-1975 h
Change Filter time in 25 hour increments. This
menu only appears if On is selected in above.
Cool On (o)
Heat On (b)
Selects operation of the reversing valve terminal
(O/B) output as an O or B terminal.
Returns to Normal Operation
5
INSTALLER/CONFIGURATION MENU
1)
This control can be configured for:
MS 2 – Multi-Stage System (no heat pump)
HP 1 – Heat Pump with one stage of compressor
HP 2 – Heat Pump with two stage compressor or two
compressor system, Gas or Electric backup
SS 1 – Single Stage System
2) GAS or Electric (ELE) fan operation. If the heating system requires the thermostat to energize the fan, select
ELE. Select GAS if the heating system energizes the fan
on a call for heat.
3) Select Cool Savings™ value – Selects the amount
of adjustment for the Cool Savings™ feature in Cool
mode with 1 (1°) being the least amount of adjustment
and 6 (6°) being the most amount of adjustment. Default
value is 0 which disables this feature. Selecting a value
greater than 0 will display Cool Savings on the screen
and enable the key for Cool Savings feature. Cool Savings is an optional energy saving feature that can reduce
your cooling costs. It is based on the principal that lower
indoor humidity makes a slightly higher temperature
feel more comfortable. Cool Savings operates during
periods of high demand which normally occur on the
hottest summer days when a cooling system may run
for hours to reach the thermostat setting. Long cooling
run times also lower the indoor humidity. Cool Savings,
very slowly, adjusts the setpoint temperature to make the
setpoint closer to the displayed room temperature, to a
maximum of the number of degrees you select. Adjusting the setpoint temperature over a long cooling run time
allows the system to reach your set temperature and turn
off. The room temperature will actually be higher than
the thermostat displays but the reduction in humidity will
allow comfort at the slightly higher temperature.
To turn this feature on in the Cool mode press Cool
Savings. The display will show “Save” next to the
setpoint temperature. When Cool Savings is making adjustments to the room temperature display “Save” will be
flashing and the displayed room temperature may vary
within the adjustment range you selected.
If “Save” is not displayed and this feature is OFF, no
change will occur when the cooling system is continuously running during periods of high demand.
4) Energy Management Recovery: (this step is skipped if
configured to be non-programmable). Energy Management Recovery (E) On enables the thermostat to start
heating or cooling early to make the building temperature
reach the program setpoint at the time you specify. Heating will start 5 minutes early for every 1° of temperature
required to reach setpoint.
Example: E On is selected and your heating is programmed to 65° at night and 70° at 7 AM. If the building temperature is 65°, the difference between 65° and
70° is 5°. Allowing 5 minutes per degree, the thermostat
setpoint will change to 70° at 6:35 AM. Cooling allows
more time per degree, because it takes longer to reach
set temperature.
5, 6 & 7) Cycle Rate Selection – The factory default setting
for Heat and Cool modes, SS1, MS2, is medium cycle
(ME). For Heat Pump, HP1, HP2, the default setting is
medium (ME). For Emer (Aux) the default setting is fast
or
cycle (FA). To change cycle rate, press the
key.
Cycle rate differentials for different settings are:
Fast
Medium Slow
MODE
FA
ME
SL
Heat (SS1, MS2)
0.4°F
0.6°F
1.7°F
Cool (SS1, MS2)
0.9°F
1.2°F
1.7°F
Heat Pump (HP1, HP2)
0.9°F
1.2°F
1.7°F
Emer (HP1, HP2)
0.6°F
1.7°F
6
8)
Select Compressor Lockout CL OFF or ON – Selecting CL ON will cause the thermostat to wait 5 minutes
between cooling cycles. This is intended to help protect
the compressor from short cycling. Some newer compressors already have a time delay built in and do not
require this feature. Your compressor manufacturer can
tell you if the lockout feature is already present in their
system. When the thermostat compressor time delay occurs, it will flash the setpoint for up to five minutes.
9) System Mode Configuration – This thermostat is
configured for Heat and Cool (SYSTEM switch with Cool,
Off, Heat) default. It can also be configured for Heat and
Cool with Auto changeover (Heat, Auto, Cool, Off), Heat
only with fan (Off, Heat), Heat only without fan, Auto only
(Auto, Off), and Cool only (Cool, Off).
10) Select Backlight Display – The display backlight improves display contrast in low lighting conditions. When
the “C” terminal is powered, selecting backlight CdL ON
will keep the light on continuously. Select backlight OFF
will turn the light on momentarily after any key is pressed.
When the “C” terminal is not powered, the light will be on
momentarily after any key is pressed no matter whether
the backlight is selected ON or OFF.
11) Select Temperature Display Adjustment 4 LO to 4 HI
– Allows you to adjust the room temperature display up
to 4° higher or lower. Your thermostat was accurately calibrated at the factory, but you have the option to change
the display temperature to match your previous thermostat. The current or adjusted room temperature will be
displayed.
12) Select F° or C° Readout – Changes the display readout
to Celsius or Fahrenheit as required.
13 & 14) Temperature Limit Range Heat or Cool – This
selection sets the maximum HEAT (13) or minimum
COOL (14) temperature for the setpoint range. Select the
or
keys. In the Run
limit temperature using the
Schedule mode, the setpoint temperature will not adjust
past the limit temperature selected. When the limit temperature is reached, trying to raise or lower the setpoint
past the limit will cause “L” to be displayed in the times
digits for about 6 seconds. This feature not available on
earlier models.
15) Program Options: Not available on 1F83, configured for
5/1/1 day or 5/2 day programming or non-programmable mode. The default setting is P3, indicating 5/1/1 day
programming. The programs per week can be changed
or
keys. A selection
to P2 or P0 by pressing the
of 0 Days for non-programmable will eliminate the need
for EMR, and that step in the menu will be skipped.
16 & 17) Select Automatic Schedule – Not available on
1F83, with just one touch of the Auto Schedule button
this feature allows you to program a desired comfort temperature into all the program periods along with a 6° set
back for night periods of both Heat and Cool programs.
Factory default is “On” for both. When Heat AS On and
Cool AS On are activated while in Heat or Cool mode,
select desired setpoint temperature and press Auto
Schedule. This value will be copied into all the morning,
day and evening program periods. The night program
periods will have a 6°F set back.
18 & 19) Select Fast Second Stage ON or OFF – Heat
pump or Multi-stage only, in the run mode, with the fast
Heat feature enabled (FA Heat On), if the Heat setpoint
temperature is manually raised by 3°F (2°C) or more
the second
above the actual temperature using
stage will energize immediately. With FA OFF, second
stage will not energize until the setpoint temperature is
1°F or more above actual temperature for more than ten
minutes. The Fast Cool feature (FA Cool) provides the
same controls when the setpoint temperature is lowered.
INSTALLER/CONFIGURATION MENU
20) Comfort Alert with Active Protection – Turn this
feature ON to enable active protection. This allows the
thermostat to identify fault codes sent by the Comfort
Alert module when compressor damage is possible and
react to those codes by turning the compressor off. Fault
codes from the Comfort Alert module will flash on the
thermostat. (Refer to Comfort Alert Yellow Alert Codes
in Troubleshooting section.) If a Comfort Alert module is
not connected, or to disable active protection, turn this
feature OFF. If a Comfort Alert module is connected and
this feature is turned OFF, the thermostat will still receive
and flash the fault codes from the Comfort Alert module,
but the active protection will not be enabled to protect the
compressor.
21) Select Daylight Saving Time Calculation – Not available on 1F83, this feature will allow the thermostat to
calculate the DST automatically and apply it to the Real
or
buttons
Time Clock display. Default On. Use
to select the feature OFF.
22) Select Filter Replacement Reminder and Set Run
Time – Select the “Change Filter” reminder On or
OFF. If selected On, press MENU to select the time
period from 25 to 1975 hours in 25 hours increments.
In a typical system, 200 hours (default) of run time is
approximately 30 days. After the selected time of blower
operation, the thermostat will display “Change Filter”
as a reminder to change or clean your air filter. When
“Change Filter” is displayed, press MENU or RUN
SCHED button to clear the display and restart the time to
the next filter change.
23) Select Reversing Valve Output – The O/B option is
factory set at “O” position. This will accommodate the
majority of heat pump applications, which require the
changeover relay to be energized in COOL. If the
thermostat you are replacing or the heat pump being
installed with this thermostat requires a “B” terminal, to
energize the changeover relay in HEAT, the O/B option
should be set at “B” position.
IMPORTANT!
OPERATING YOUR THERMOSTAT
Choose the Fan Setting (Auto or On)
Press the FAN button to Auto or On.
Fan Auto is the most commonly selected setting and runs the
fan only when the heating or cooling system is on.
Fan On runs the fan continuously for increased air circulation
or to allow additional air cleaning.
Choose the System Setting
(Heat, Off, Cool, Auto, Emer)
Press the SYSTEM button to select:
Heat: Thermostat controls only the heating system.
Off: Heating and Cooling systems are off.
Cool: Thermostat controls only the cooling system.
Auto: Auto Changeover is used in areas where both heating
and cooling may be required on the same day. AUTO allows
the thermostat to automatically select heating or cooling
depending on the indoor temperature and the selected heat
and cool temperatures. When using AUTO, be sure to set the
Cooling temperatures more than 1° Fahrenheit higher than
the heating temperature.
Emer: (Heat Pump models) Thermostat controls only backup
heating system.
Manual Operation for Non-Programmable
Mode
Press the SYSTEM button to select Heat or Cool and use
the
or
buttons to adjust the temperature to your
desired setting. After selecting your desired settings you can
also press the SYSTEM button to select AUTO to allow the
thermostat to automatically change between Heat and Cool.
Manual Operation (Bypassing the Program)
Programmable Thermostats
Press
or
and then the HOLD button and adjust the
temperature wherever you like. This will override the program.
The HOLD feature bypasses the program and allows you
to adjust the temperature manually, as needed. Whatever
temperature you set in HOLD will be maintained 24 hours
a day, until you manually change the temperature or press
Run Sched to cancel HOLD and resume the programmed
schedule.
Program Override (Temporary Override)
Press
or
buttons to adjust the temperature. This
will override the temperature setting for two hours minimum
or until the next programmed time. To cancel the temporary
setting at any time and return to the program, press Run
Sched. If the SYSTEM button is pressed to select AUTO
the thermostat will change to Heat or Cool, whichever ran
last. If it switches to heat but you want cool, or it changes
to cool but you want heat, press both
and
buttons
simultaneously to change to the other mode.
PROGRAMMING (For Programmable Model Only)
Set Current Time and Date
1) Press Menu and then Time button once. The display
will show the hour only.
2) Press and hold either the
or
button until you
reach the correct hour and AM/PM designation (AM
begins at midnight, PM begins at noon).
3) Press Time once again. The display window will show
the minutes only.
4) Press and hold either the
or
button until you
reach the correct minutes.
5)
6)
Additional presses of Time will advance the display to
show the year, month and date of month. Press the
or
button to change the display to the correct setting for each.
Press Run Sched to exit the Time mode.
7
PROGRAMMING (For Programmable Model Only)
9)
Enter the Heating Program
1)
2)
3)
4)
5)
6)
7)
8)
Press SYSTEM button to select “Heat” in the system
switch area indicating the active mode being programmed.
Press the Menu button and then press Schedule.
The top of the display will show the day(s) being programmed. The time and temperature (flashing) are also
displayed. “1” will also be displayed to indicate the period.
Press
or
button to change the temperature to
your selected temperature for the 1st heating period.
Press Time button, time will flash.
Press
or
button to adjust the start time for the
1st period.
The time will change in 15 minute increments.
After you have set the time and the temperature for
the period to begin, press Schedule to advance to the
next program period.
Repeat steps 2 through 8 until all of the program times
and temperatures are set for all program periods on
that day.
10) Press Schedule to the next day and repeat steps 2
through 9.
11) When programming is complete and all of the times and
temperatures match your desired heating schedule, press
Run Schedule. The thermostat will now run your program.
Enter the Cooling Program
1)
2)
Press SYSTEM button to select “Cool” in the system
switch area indicating the active mode being programmed.
Follow Enter Heating Program instructions for entering
cooling times and temperatures.
Energy Saving ENERGY STAR® Factory Pre-Program
The programmable thermostats are programmed with the
energy saving settings shown in the table below for all days
of the week. If this program suits your needs, simply set the
Wake Up
(Period 1)
Heating
Program
Cooling
Program
thermostat clock and press the RUN Sched button.
The table below shows the factory set heating and cooling
schedule for all days of the week.
Leave For Work
(Period 2)
Return Home
(Period 3)
Go To Bed
(Period 4)
6:00 AM
70°F
8:00 AM
62°F
5:00 PM
70°F
10:00 PM
62°F
6:00 AM
75°F
8:00 AM
83°F
5:00 PM
75°F
10:00 PM
78°F
Planning Your Program – Important
The Heating and Cooling Program schedules below allow you
to pencil in your own program times and temperatures.
The programmable comes configured for 5/1/1 day programming and can also be configured for 5/2 day programming
(see configuration section).
Factory settings are listed on Monday through Friday, Saturday and Sunday. If you are re-programming a 5/2 day schedule, pencil in your own times and temperatures directly below
the factory times and temperatures.
If you are re-programming a 5+1+1 fill in all lines with the
times and temperatures you want.
Keep the following guidelines in mind when planning your
program.
• In Heating, lower temperatures will save energy.
• In Cooling, higher temperatures will save energy.
• If you plan on using Auto Changeover, do not program
the heating higher than the cooling.
Worksheet for Re-Programming 5/2 Day and 5+1+1 Day Program
Heating
Program
Wake Up
(Period 1)
6:00 AM 70°F
Leave For Work
(Period 2)
8:00 AM 62°F
Return Home
(Period 3)
5:00 PM 70°F
Go To Bed
(Period 4)
10:00 PM 62°F
Sat-Sun
or Sat
6:00 AM
70°F
8:00 AM
62°F
5:00 PM
70°F
10:00 PM
62°F
Sun
5+1+1 only
6:00 AM
70°F
8:00 AM
62°F
5:00 PM
70°F
10:00 PM
62°F
Mo-Fri
Cooling
Program
Wake Up
(Period 1)
6:00 AM 75°F
Leave For Work Return Home
(Period 2)
(Period 3)
8:00 AM 83°F 5:00 PM 75°F
Go To Bed
(Period 4)
10:00 PM 78°F
Sat-Sun
or Sat
6:00 AM
75°F
8:00 AM
83°F
5:00 PM
75°F
10:00 PM
78°F
Sun
5+1+1 only
6:00 AM
75°F
8:00 AM
83°F
5:00 PM
75°F
10:00 PM
78°F
Mo-Fri
8
TROUBLESHOOTING
Reset Operation
Note: When thermostat is reset, installer configuration menu
settings and programming will reset to factory settings.
If a voltage spike or static discharge blanks out the display
or causes erratic thermostat operation, you can reset the
thermostat by removing the wires from terminals R and C
(do not short them together) and removing batteries for 2
minutes. After resetting the thermostat, replace the wires and
batteries. If the thermostat has been reset and still does not
function correctly contact your heating/cooling service person
or place of purchase.
Note: Be sure to review the installer configuration menu
settings.
To reset the programming, clock and configuration settings,
press
and
and the FAN button simultaneously. The
thermostat should go blank and then all segments will be
displayed momentarily.
Symptom
Possible Cause
Correction Action
No Heat/No Cool/No Fan
(common problems)
1. Blown fuse or tripped circuit breaker.
2. Furnace power switch to OFF.
3. Furnace blower compartment door or
panel loose or not properly installed.
4. Loose connection to thermostat or
system.
Replace fuse or reset breaker.
Turn switch to ON.
Replace door panel in proper position to engage safety
interlock or door switch.
Tighten connections.
No Heat
1. Pilot light not lit.
2. Furnace Lock-Out Condition. Heat
may also be intermittent.
Re-light pilot.
Many furnaces have safety devices that shut down when
a lock-out condition occurs. If the heat works intermittently
contact the furnace manufacturer or local HVAC service
person for assistance.
Diagnostic: Set SYSTEM Switch to HEAT and raise the
setpoint above room temperature. Within a few seconds
the thermostat should make a soft click sound. This sound
usually indicates the thermostat is operating properly. If
the thermostat does not click, try the reset operation listed
above. If the thermostat does not click after being reset
contact your heating and cooling service person or place
of purchase for a replacement. If the thermostat clicks,
contact the furnace manufacturer or a HVAC service
person to verify the heating is operating correctly.
3. Heating system requires service or
thermostat requires replacement.
No Cool
1. Cooling system requires service or
thermostat requires replacement.
Same as diagnostic for No Heat condition except set the
thermostat to COOL and lower the setpoint below the room
temperature. There may be up to a five minute delay before
the thermostat clicks in Cooling.
1. Possible short in wiring.
2. Possible short in thermostat.
3. Possible short in heat/cool/fan system.
4. FAN Switch set to Fan ON.
Check each wire connection to verify they are not shorted
or touching together. No bare wire should stick out from
under terminal block. Try resetting the thermostat as
described above. If the condition persists the manufacturer
of your system or service person can instruct you on how
to test the Heat/Cool system for correct operation. If the
system operates correctly, replace the thermostat.
Thermostat Setting &
Thermostat Thermometer
Disagree
1. Thermostat thermometer setting
requires adjustment.
The thermometer can be adjusted +/- 4 degrees. See
Temperature Display Adjustment in the Configuration Menu
section.
Furnace (Air Conditioner)
Cycles Too Fast or Too
Slow (narrow or wide
temperature swing)
1. The location of the thermostat and/or
the size of the Heating System may
be influencing the cycle rate.
Digital thermostats provide precise control and cycle faster
than older mechanical models. The system turns on and off
more frequently but runs for a shorter time so there is no
increase in energy use. If you would like an increased cycle
time, choose SL for slow cycle in the Configuration menu,
step 6 (heat), 7 (cool) or 8 (heat pump). If an acceptable
cycle rate is not achieved, contact a local HVAC service
person for additional suggestions.
Heat, Cool or Fan
Runs Constantly
9
TROUBLESHOOTING
Comfort Alert Codes
The Comfort Alert diagnostics product monitors the air conditioning outdoor systems with single phase Copeland Scroll
compressors. Abnormal system and electrical conditions are
indicated by flashing ALERT codes on the yellow LED on the
Comfort Alert module. The flash codes are transmitted to the
thermostat by the Comfort Alert Thermostat interface module.
The Comfort Alert compatible thermostat displays “Call For
Service” that flashes at the same rate as the yellow LED on
the Comfort Alert module.
10
Comfort Alert Yellow Alert Codes
1 Flash
Long run time
2 Flashs
System pressure trip
3 Flashs
Short cycling
4 Flashs
Locked rotor
5 Flashs
Open circuit
6 Flashs
Open start circuit
7 Flashs
Open run circuit
8 Flashs
Welded Contactor
9 Flashs
Low voltage
NOTES
11
HOMEOWNER HELP LINE: 1-800-284-2925
White-Rodgers is a division
of Emerson Electric Co.
The Emerson logo is a
trademark and service mark
of Emerson Electric Co.
www.white-rodgers.com